AAAAD 19QUALITY QUALITY THE TRADE DESIGNATION OF THE GRADE AS RELATED TO THE DEGREE OF EXCELLENCE. SELECT REPLY CODE 10AA00 AAABD 01COLOR COLOR COLOR IS A PHENOMENON OF LIGHT /AS RED,BROWN,YELLOW,GRAY/ OR VISUAL PERCEPTION THAT ENABLES ONE TO DIFFERENTIATE OTHERWISE IDENTICAL OBJECTS. COLOR OF GLASS REFERS TO THE MATERIAL ONLY FOR ALL GLASS OTHER THAN SPANDREL GLASS AND TO THE FIRE FUSED COLOR ON THE SURFACE OF SPANDREL GLASS. SELECT REPLY CODE 10AD06 AAACD 19TRANSPARENCY TRANSPARENCY TRANSPARENCY OF GLASS PERTAINS TO THE MATERIAL AND ANY SURFACE TREATMENT /AS ETCHING,SANDBLASTING,OR THE LIKE/ OR FIRE FUSED COLOR /WITH OR WITHOUT BACKING/. IT IS THE MEASURE OF ABILITY TO TRANSMIT LIGHT AND ALLOW VISUAL PERCEPTION THROUGH THE GLASS. SELECT REPLY CODE 10AD56 AAADD 19PATTERN PATTERN THE PATTERN IS THE ARTISTIC OR MECHANICAL DESIGN OF THE GLASS. SELECT REPLY CODE 10AA02 AAAED 17SURFACE TREATMENT,SIDE ONE SIDE ONE SURFACE TREATMENT SURFACE TREATMENT IS THE PROCESS USED TO IMPROVE OR ALTER THE SURFACE. IN REFERENCE TO GLASS,TREATMENT IS THE GRINDING,POLISHING,ETCHING,FIRE FUSED COLOR,OR THE LIKE,AS APPLIED TO THE SURFACE. SELECT REPLY CODE 10AA03 AAAFD 17SURFACE TREATMENT,SIDE TWO SIDE TWO SURFACE TREATMENT SURFACE TREATMENT IS THE PROCESS USED TO IMPROVE OR ALTER THE SURFACE. IN REFERENCE TO GLASS,TREATMENT IS THE GRINDING,POLISHING,ETCHING,FIRE FUSED COLOR,OR THE LIKE,AS APPLIED TO THE SURFACE. SELECT REPLY CODE 10AA03 AAAGD 19FINISH,EDGE,THICKNESS THICKNESS EDGE FINISH THICKNESS EDGE FINISH IS THE FINISH OF THE BOUNDARY SURFACE JOINING THE TWO FACE SURFACES. SELECT REPLY CODE 10AA04 AAAHD /D/ 19PATTERN,MESH,WIRE GLASS WIRE GLASS MESH PATTERN WIRED GLASS MESH PATTERN IS THE DEFINITE PATTERN OF TWISTED OR WELDED WIRE,COMPLETELY IMBEDDED WITHIN THE GLASS. SELECT REPLY CODE 10AD07 AAAJJ 04LENGTH,MESH,WIRED GLASS WIRED GLASS MESH LENGTH THE LONGEST MEASUREMENT BETWEEN OPPOSITE CORNERS OF A DIAMOND OR HEXAGON WIRE MESH PATTERN,OR THE LONGER SIDE OF A RECTANGULAR WIRE MESH PATTERN. INCLUDES UNIT OF MEASURE DESIGNATION. 1D AND 1B MODE REPLY11AA05 AAAKJ 04WIDTH,MESH,WIRED GLASS WIRED GLASS MESH WIDTH THE SHORTEST MEASUREMENT BETWEEN OPPOSITE CORNERS OF A DIAMOND OR HEXAGON WIRE MESH PATTERN,OR THE SHORTER SIDE OF A RECTANGULAR WIRE MESH PATTERN. INCLUDES UNIT OF MEASURE DESIGNATION. 1D AND 1B MODE REPLY11AA05 AAALD 18TYPE,HOLE,TONGUE TONGUE HOLE TYPE INDICATES THE TYPE OF HOLE/S/ IN THE TONGUE. SELECT REPLY CODE 10AB68 AAAMD /D/ 19CONFIGURATION,PLANE PLANE CONFIGURATION THE GEOMETRIC FIGURE AS VIEWED FROM A POINT PERPENDICULAR TO THE LARGEST SURFACE. SELECT REPLY CODE 10AD07 AAANJ A18TYPE AND QUANTITY,NUT,INTEGRAL INTEGRAL NUT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF INTEGRAL NUT(S) PROVIDED. 1D AND 1A MODE REPLY12AH33 AAAPD 19PROTECTION,ENVIRONMENTAL,CUSHIONING CUSHIONING ENVIRONMENTAL PROTECTION THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT THE CUSHIONING IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY. SELECT REPLY CODE 10AA65 AAAQJ 04LENGTH,OVERALL,CLAMP CLAMP OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS OF THE CLAMP,WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 AAARJ 04SIZE ACCOMMODATED,PIPE,NOMINAL NOMINAL PIPE SIZE ACCOMMODATED A MEASUREMENT OF THE PIPE SIZE THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 AAASD 19CHARACTERISTIC,ABSORBING,HEAT HEAT ABSORBING CHARACTERISTIC THE ABILITY OF GLASS TO INTERCEPT APPRECIABLE PORTIONS OF RADIANT ENERGY /ESPECIALLY SOLAR ENERGY/ BY VIRTUE OF ITS LIGHT TRANSMISSION CHARACTERISTICS. SELECT REPLY CODE 10AA06 AAATD /D/ 07CHARACTERISTIC,REDUCING,LIGHT LIGHT REDUCING CHARACTERISTIC AN INDICATION OF WHETHER OR NOT AN OBJECT IS INTENDED FOR REDUCING THE AMOUNT OF VISIBLE LIGHT TRANSMISSION FOR THE PURPOSE OF REDUCING GLARE. SELECT REPLY CODE 10AA07 AAAUD /D/ 07CHARACTERISTIC,RETARDING,FIRE FIRE RETARDING CHARACTERISTIC AN INDICATION OF WHETHER OR NOT AN OBJECT WILL REMAIN SUBSTANTIALLY UNCHANGED WHEN SUBJECTED TO EXTREMELY HIGH TEMPERATURES. SELECT REPLY CODE 10AA08 AAAVD /D/ 19CHARACTERISTIC,TEMPER TEMPER CHARACTERISTIC TEMPERED GLASS IS GLASS SUBJECTED TO A PROCESS OF HEAT TREATMENT AND RAPID COOLING WHICH CREATES A HIGHLY COMPRESSED ZONE ON THE OUTER SURFACE. PLEASE USE MRC BDPZ IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA09 AAAWA /D/ 12QUANTITY PER SET/N/,BRUSH BRUSH QUANTITY PER SET/N/ THE NUMBER OF BRUSHES COMPRISING A BRUSH SET. 1A MODE REPLY 0 AAAXJ /D/X19NUMBER,CODE AND PART,MANUFACTURER MANUFACTURER CODE AND PART NUMBER THE MANUFACTURERS CODE AND PART NUMBER FOR EACH TYPE OF BRUSH COMPRISING A BRUSH SET. 1D AND 1A MODE REPLY15AA10 AAAYD /D/ 18TYPE,BRUSH BRUSH TYPE THE BASIC STYLE OR DESIGN TO WHICH THE BRUSH CONFORMS. SELECT REPLY CODE 10AA11 AAAZA /D/ 12QUANTITY,WAFER WAFER QUANTITY THE NUMBER OF INDIVIDUAL PIECES (WAFER) WHICH MAKE UP AN ITEM. 1A MODE REPLY 0 AABAJ /D/ 04THICKNESS,WAFER WAFER THICKNESS THE THICKNESS OF EACH SECTION, OR WAFER, WHICH COMPRISES AN ITEM. 1D AND 1B MODE REPLY11AA05 AABBA 12QUANTITY PER MULTIPLE BRUSH,COMPONENT BRUSH COMPONENT BRUSH QUANTITY PER MULTIPLE BRUSH THE NUMBER OF COMPONENT BRUSHES WHICH MAKE UP A MULTIPLE OR PRESSURE SPRING MULTIPLE BRUSH. 1A MODE REPLY 0 AABCD 19MEDIA FOR WHICH GASKET IS DESIGNED MEDIA FOR WHICH GASKET IS DESIGNED THE TYPE OF SERVICE WITH WHICH THE ITEM IS DESIGNED TO BE USED. SELECT REPLY CODE 10AB75 AABDD /D/ 19SURFACE FOR WHICH DESIGNED,CONTACT CONTACT SURFACE FOR WHICH DESIGNED THE TYPE OF CONTACT SURFACE ON WHICH THE ITEM IS DESIGNED TO OPERATE. SELECT REPLY CODE 10AA12 AABED /D/ 09MATERIAL,BRUSH OR CARBON STOCK BRUSH OR CARBON STOCK MATERIAL THE COMPOSITION USED TO MANUFACTURE THE BRUSH OR CARBON STOCK. SELECT REPLY CODE 10AD09 AABFD /D/ 19COATING,BRUSH BRUSH COATING ANY COATING APPLIED TO THE SURFACE OF THE BRUSH. SELECT REPLY CODE 10AA13 AABGD /D/ 09MATERIAL,COATING,BRUSH BRUSH COATING MATERIAL THE MATERIAL USED TO COAT THE BRUSH. SELECT REPLY CODE 10AD09 AABHD /D/ 14SHAPE,FACE,CONTACT,BRUSH BRUSH CONTACT FACE SHAPE THE PHYSICAL CONFIGURATION OF THE END OF THE BRUSH WHICH MAKES CONTACT WITH THE CONDUCTING SURFACE. SELECT REPLY CODE 10AD07 AABJD /D/ 14SHAPE,TOP,BRUSH BRUSH TOP SHAPE THE PHYSICAL CONFIGURATION OF THE TOP PORTION OF THE BRUSH. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. SELECT REPLY CODE 10AD07 AABKD /D/ 08LOCATION,SHOULDER SHOULDER LOCATION INDICATES THE LOCATION OF THE SHOULDER/S/ ON THE ITEM. SELECT REPLY CODE 10AE46 AABLD /D/ 08LOCATION,CORNER,BEVELED BEVELED CORNER LOCATION INDICATES THE LOCATION OF THE BEVELED CORNER/S/ ON THE ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. SELECT REPLY CODE 10AE46 AABMD /D/ 08LOCATION,EDGE,BEVELED BEVELED EDGE LOCATION INDICATES THE LOCATION OF THE BEVELED EDGE/S/ ON THE ITEM. SELECT REPLY CODE 10AE46 AABND /D/ 19SLOPE,BEVEL,TOP TOP BEVEL SLOPE INDICATES WHETHER THE TOP BEVEL SLOPES TO THE FRONT OR TO THE BACK OF THE ITEM. SELECT REPLY CODE 10AA14 AABPD /D/ 19FEATURES,BODY BODY FEATURES ANY BODY FEATURES, SUCH AS HOLES, GROOVES, NOTCHES, OR SLOTS CUT OR DRILLED INTO OR THROUGH THE ITEM. SELECT REPLY CODE 10AA15 AABQD /D/ 19MARKING,LINE,WEAR WEAR LINE MARKING ANY SPECIAL MARKING ON THE ITEM WHICH SHOWS THE PERCENTAGE OF WEAR. SELECT REPLY CODE 10AA16 AABRD /D/ 18TYPE,CLIP,BRUSH BRUSH CLIP TYPE INDICATES THE TYPE OF METAL CLIP ATTACHED TO THE BRUSH. SELECT REPLY CODE 10AA47 AABSA /D/ 12QUANTITY,SHUNT SHUNT QUANTITY THE NUMBER OF SHUNTS OR OTHER FLEXIBLE CONDUCTORS ATTACHED TO THE ITEM.A SHUNT MAY CONSIST OF MORE THAN ONE CABLE PROVIDED THE CABLES ARE ATTACHED TO THE ITEM IN THE SAME SHUNT POSITION. 1A MODE REPLY 0 AABTD /D/ 18TYPE,CONNECTION,SHUNT SHUNT CONNECTION TYPE INDICATES THE TYPE OF SHUNT CONNECTION USED IN ATTACHING THE SHUNT/S/ TO THE ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. SELECT REPLY CODE 10AA18 AABUA 03DESIGNATOR,POSITION,SHUNT SHUNT POSITION DESIGNATOR STANDARD LOCATION BY POSITION NUMBER FOR SHUNT/S/. 1A MODE REPLY 0 AABVA /D/ 12QUANTITY PER SHUNT POSITION,CABLE CABLE QUANTITY PER SHUNT POSITION THE NUMBER OF SEPARATE CABLES ATTACHED TO THE ITEM IN EACH SHUNT POSITION. 1A MODE REPLY 0 AABWA /D/ 12QUANTITY PER SHUNT CABLE,STRAND STRAND QUANTITY PER SHUNT CABLE THE NUMBER OF STRANDS, CONSISTING OF A NUMBER OF WIRES GROUPED TOGETHER, WHICH MAKE UP THE OVERALL SHUNT CABLE WHEN BRAIDED OR TWISTED TOGETHER. 1A MODE REPLY 0 AABXA /D/ 12QUANTITY PER CABLE STRAND,WIRE WIRE QUANTITY PER CABLE STRAND THE NUMBER OF INDIVIDUAL WIRES CONTAINED IN EACH CABLE STRAND. 1A MODE REPLY 0 AABYD /D/ 14SHAPE,CROSS-SECTIONAL,CABLE,SHUNT SHUNT CABLE CROSS-SECTIONAL SHAPE THE PHYSICAL CONFIGURATION OF THE SHUNT CABLE WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 AABZJ /D/ 04WIDTH,CABLE,SHUNT SHUNT CABLE WIDTH THE LARGEST CROSS-SECTIONAL DIMENSION OF THE FLAT SHAPED SHUNT CABLE MEASURED AT RIGHT ANGLES TO THE LENGTH OF THE CABLE. 1D AND 1B MODE REPLY11AA05 AACAJ /D/ 04THICKNESS,CABLE,SHUNT SHUNT CABLE THICKNESS THE SMALLEST CROSS-SECTIONAL DIMENSION OF THE FLAT SHAPED SHUNT CABLE MEASURED AT RIGHT ANGLES TO THE LENGTH OF THE CABLE. 1D AND 1B MODE REPLY11AA05 AACBA /D/ 04SIZE,AWG,CABLE,SHUNT SHUNT CABLE AWG SIZE THE NEAREST AMERICAN WIRE GAGE SIZE OF THE ROUND SHUNT CABLE. 1A MODE REPLY 0 AACCD /D/ 09MATERIAL,WIRE,SHUNT SHUNT WIRE MATERIAL THE MATERIAL OF THE WIRES WHICH MAKE UP THE SHUNT CABLE. SELECT REPLY CODE 10AD09 AACDD /D/ 19FINISH,WIRE,SHUNT SHUNT WIRE FINISH THE COATING, DIP, OR PLATING APPLIED FOR ENVIRONMENTAL PROTECTION TO THE WIRES THAT MAKE UP THE SHUNT. SELECT REPLY CODE 10AD09 AACEJ /D/ 04LENGTH,SHUNT SHUNT LENGTH THE SHUNT LENGTH IS THE DISTANCE FROM THE EXTREME TOP OF THE ITEM TO THE CENTER OF THE HOLE OR SLOT IN THE TERMINAL, OR THE CENTER OF THE INSERTED PORTION OF A PLUG TERMINAL, OR THE END OF THE SHUNT FOR A CAP TYPE TERMINAL, OR IF THERE IS NO TERMINAL, TO THE END OF THE SHUNT, OR BETWEEN ITEMS FOR PAIRED-SINGLE PHASE ITEMS. 1D AND 1B MODE REPLY11AA05 AACFD /D/ 09MATERIAL,INSULATION,SHUNT SHUNT INSULATION MATERIAL THE COVERING OR SLEEVING APPLIED OVER THE SHUNT TO INSULATE IT ELECTRICALLY. SELECT REPLY CODE 10AD09 AACGD /D/ 11METHOD,TERMINATION,SHUNT SHUNT TERMINATION METHOD THE MEANS USED TO TERMINATE THE END OF THE SHUNT/S/. SELECT REPLY CODE 10AA19 AACHA /D/ 12QUANTITY,TERMINAL,SHUNT SHUNT TERMINAL QUANTITY THE NUMBER OF TERMINALS ATTACHED TO THE SHUNT/S/. 1A MODE REPLY 0 AACJD /D/ 18TYPE,TERMINAL,SHUNT SHUNT TERMINAL TYPE INDICATES THE TYPE OF TERMINAL ATTACHED TO THE SHUNT/S/. SELECT REPLY CODE 10AA20 AACKA /D/ 13THREADS PER INCH,TERMINAL TERMINAL THREADS PER INCH THE NUMBER OF SINGLE SCREW THREADS PER INCH OF THE THREADED PLUG TERMINAL. 1A MODE REPLY 0 AACLD /D/ 18TYPE,SPRING,PRESSURE PRESSURE SPRING TYPE INDICATES THE TYPE OF PRESSURE SPRING/S/ PROVIDED FOR USE WITH THE ITEM. SELECT REPLY CODE 10AA21 AACMA /D/ 12QUANTITY,SPRING,PRESSURE PRESSURE SPRING QUANTITY THE NUMBER OF PRESSURE SPRINGS PROVIDED WITH THE ITEM. 1A MODE REPLY 0 AACND /D/ 09MATERIAL,SPRING,PRESSURE,BRUSH BRUSH PRESSURE SPRING MATERIAL THE MATERIAL OF WHICH THE SPRING/S/ IS MADE. SELECT REPLY CODE 10AD09 AACPD /D/ 19FINISH,MATERIAL,SPRING,PRESSURE PRESSURE SPRING MATERIAL FINISH THE PROTECTIVE SURFACE COATING APPLIED TO THE MATERIAL OF WHICH THE SPRING/S/ IS MADE. SELECT REPLY CODE 10AD09 AACQJ A10SPEED,PERIPHERAL PERIPHERAL SPEED THE SPEED OF THE COMMUTATOR OR SLIP-RING FOR WHICH THE ITEM IS DESIGNED. 1D AND 1A MODE REPLY11AA22 AACRD 03DESIGNATION,USE,PRIMARY PRIMARY USE DESIGNATION AN INDICATION OF WHETHER THE ITEM/S/ ARE PRIMARILY DESIGNED FOR USE ON GROUND EQUIPMENT OR FOR USE ON OTHER THAN GROUND EQUIPMENT. SELECT REPLY CODE 10AA23 AACSD /D/ 19POSITION,BRUSH BRUSH POSITION THE POSITION OF THE BRUSH IN RELATION TO THE DIRECTION OF ROTATION OF THE COMMUTATOR OR SLIP-RING, WHEN THE BRUSH IS IN THE OPERATING POSITION. SELECT REPLY CODE 10AA24 AACTD 19CURRENT FOR WHICH DESIGNED,CIRCUIT CIRCUIT CURRENT FOR WHICH DESIGNED THE TYPE OF ELECTRICAL CIRCUIT IN WHICH THE ITEM IS DESIGNED TO BE USED. SELECT REPLY CODE 10AB62 AACUJ 04THICKNESS,MAJOR MAJOR THICKNESS THE MAJOR MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM, IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 AACVJ /D/ 04THICKNESS,MINOR MINOR THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 AACWB /D/ 04ANGEL,BEVEL,FACE,CONTACT CONTACT FACE BEVEL ANGEL NONE. 1B MODE REPLY 0 AACXJ /D/ 04WIDTH,TOE,BOTTOM BOTTOM TOE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BOTTOM TOE, IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AACYJ /D/ 04RADIUS,FACE,CONTACT CONTACT FACE RADIUS NONE. 1D AND 1B MODE REPLY11AA05 AACZJ /D/ 04DEPTH FROM SIDE OF BRUSH,BEVEL BEVEL DEPTH FROM SIDE OF BRUSH NONE. 1D AND 1B MODE REPLY11AA05 AADAJ /D/ 04DEPTH FROM TOP OF BRUSH,BEVEL BEVEL DEPTH FROM TOP OF BRUSH NONE. 1D AND 1B MODE REPLY11AA05 AADBJ /D/ 04HEIGHT,SHOULDER SHOULDER HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 AADCJ /D/ 04WIDTH,SHOULDER SHOULDER WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AADDB /D/ 04ANGLE,BEVEL,TOP TOP BEVEL ANGLE NONE. 1B MODE REPLY 0 AADEJ /D/ 04WIDTH,BEVEL,TOP,PARTIAL PARTIAL TOP BEVEL WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AADFJ /D/ 04WIDTH,TOE,TOP TOP TOE WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AADGJ /D/ 04DISTANCE FROM EDGE OF BRUSH TO EDGE OF SLOT DISTANCE FROM EDGE OF BRUSH TO EDGE OF SLOT NONE. 1D AND 1B MODE REPLY11AA05 AADHJ 04WIDTH,SLOT SLOT WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AADJJ 04DEPTH,SLOT SLOT DEPTH THE MEASUREMENT BETWEEN SPECIFIED POINTS OF THE SLOT,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 AADKJ /D/ 04DISTANCE FROM SIDE OF BRUSH TO CENTER OF NOTCH DISTANCE FROM SIDE OF BRUSH TO CENTER OF NOTCH NONE. 1D AND 1B MODE REPLY11AA05 AADLB /D/ 04ANGLE,NOTCH NOTCH ANGLE NONE. 1B MODE REPLY 0 AADMJ /D/ 04DEPTH,NOTCH NOTCH DEPTH NONE. 1D AND 1B MODE REPLY11AA05 AADNJ /D/ 04RADIUS,TOP,CONVEX CONVEX TOP RADIUS NONE. 1D AND 1B MODE REPLY11AA05 AADPJ /D/ 04DISTANCE OF CENTER OF CURVATURE FROM LONG SIDE OF BRUSH DISTANCE OF CENTER OF CURVATURE FROM LONG SIDE OF BRUSH NONE. 1D AND 1B MODE REPLY11AA05 AADQJ /D/ 04DIAMETER,HEAD HEAD DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AADRJ /D/ 04DIAMETER,MAJOR,HEAD HEAD MAJOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AADSJ /D/ 04DIAMETER,MINOR,HEAD HEAD MINOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AADTJ /D/ 04HEIGHT,HEAD HEAD HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 AADUJ /D/ 04LENGTH,NECK NECK LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AADVJ /D/ 04DIAMETER,NECK NECK DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AADWB /D/ 04ANGLE,BEVEL,SLOT SLOT BEVEL ANGLE NONE. 1B MODE REPLY 0 AADXB /D/ 04ANGLE,HEAD HEAD ANGLE NONE. 1B MODE REPLY 0 AADYJ /D/ 04DISTANCE FROM EDGE OF BRUSH TO EDGE OF SLOT DISTANCE FROM EDGE OF BRUSH TO EDGE OF SLOT NONE. 1D AND 1B MODE REPLY11AA05 AADZJ /D/ 04WIDTH,SLOT SLOT WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AAEAJ /D/ 04LENGTH,SLOT SLOT LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AAEBJ /D/ 04DISTANCE FROM TOP OF BRUSH TO TOP OF SLOT DISTANCE FROM TOP OF BRUSH TO TOP OF SLOT NONE. 1D AND 1B MODE REPLY11AA05 AAECJ /D/ 04DEPTH,GROOVE GROOVE DEPTH NONE. 1D AND 1B MODE REPLY11AA05 AAEDJ /D/ 04SIZE,HOLE HOLE SIZE NONE. 1D AND 1B MODE REPLY11AA05 AAEEA 12QUANTITY,SPROCKETS SPROCKETS QUANTITY THE NUMBER OF SPROCKETS INCLUDED ON THE ITEM. 1A MODE REPLY 0 AAEFJ /D/ 04DISTANCE FROM EDGE OF BRUSH TO CENTER OF HOLE DISTANCE FROM EDGE OF BRUSH TO CENTER OF HOLE NONE. 1D AND 1B MODE REPLY11AA05 AAEGJ /D/ 04DISTANCE FROM CENTER OF FIRST HOLE TO CENTER OF SECOND HOLE DISTANCE FROM CENTER OF FIRST HOLE TO CENTER OF SECOND HOLE NONE. 1D AND 1B MODE REPLY11AA05 AAEHJ /D/ 04DISTANCE FROM TOP OF BRUSH TO CENTERLINE OF HOLES DISTANCE FROM TOP OF BRUSH TO CENTERLINE OF HOLES NONE. 1D AND 1B MODE REPLY11AA05 AAEJJ /D/ 04DISTANCE FROM EDGE OF BRUSH TO EDGE OF GROOVE DISTANCE FROM EDGE OF BRUSH TO EDGE OF GROOVE NONE. 1D AND 1B MODE REPLY11AA05 AAEKJ /D/ 04WIDTH,GROOVE GROOVE WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AAELA 13THREADS PER INCH THREADS PER INCH THE NUMBER OF SINGLE SCREW THREADS PER INCH OF THE THREADED PORTION. 1A MODE REPLY 0 AAEMJ /D/ 04WIDTH,CLIP CLIP WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AAENJ /D/ 04LENGTH,OVERHANG,CLIP CLIP OVERHANG LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AAEPB /D/ 04ANGLE,BEVEL,CLIP CLIP BEVEL ANGLE NONE. 1B MODE REPLY 0 AAEQJ /D/ 04HEIGHT,INSIDE,OPENING,CLIP CLIP OPENING INSIDE HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 AAERJ /D/ 04WIDTH,INSIDE,OPENING,CLIP CLIP OPENING INSIDE WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AAESJ /D/ 04DISTANCE FROM TOP OF BRUSH TO TOP OF CLIP DISTANCE FROM TOP OF BRUSH TO TOP OF CLIP NONE. 1D AND 1B MODE REPLY11AA05 AAETJ /D/ 04DISTANCE FROM SHORT SIDE OF BRUSH TO SAIL DISTANCE FROM SHORT SIDE OF BRUSH TO SAIL NONE. 1D AND 1B MODE REPLY11AA05 AAEUJ /D/ 04DIAMETER,HOLE,TERMINAL TERMINAL HOLE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AAEVJ /D/ 04WIDTH,SLOT,TERMINAL TERMINAL SLOT WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AAEWJ 04WIDTH,TERMINAL TERMINAL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TERMINAL,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AAEXJ /D/ 04LENGTH,SLOT,TERMINAL TERMINAL SLOT LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AAEYJ 04LENGTH,TERMINAL TERMINAL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TERMINAL,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AAEZJ /D/ 04DIAMETER,MAJOR,TERMINAL TERMINAL MAJOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AAFAJ /D/ 04DIAMETER,MINOR,TERMINAL TERMINAL MINOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AAFBJ 04DIAMETER,TERMINAL TERMINAL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A TERMINAL,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AAFCJ 04THICKNESS,TERMINAL TERMINAL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE TERMINAL,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 AAFDJ /D/ 04THICKNESS,REDUCED PORTION OF TERMINAL REDUCED PORTION OF TERMINAL THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 AAFEJ /D/ 04WIDTH,MAJOR,TERMINAL TERMINAL MAJOR WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AAFFJ /D/ 04WIDTH,MINOR,TERMINAL TERMINAL MINOR WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AAFGJ /D/ 04LENGTH,EAR EAR LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AAFHJ /D/ 04WIDTH,EAR EAR WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AAFJJ 04DIAMETER,TERMINAL,TYPE,PLUG,UNTHREADED UNTHREADED PLUG TYPE TERMINAL DIAMETER NONE. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 1D AND 1B MODE REPLY11AA05 AAFKJ /D/ 04LENGTH,TERMINAL,TYPE,PLUG PLUG TYPE TERMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AAFLJ /D/ 04DIAMETER,TERMINAL,TYPE,PLUG,THREADED THREADED PLUG TYPE TERMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AAFMJ /D/ 04DIAMETER,WIRE,SPRING SPRING WIRE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AAFNJ /D/ 04DIAMETER AT TERMINAL END,OUTSIDE,SPRING SPRING OUTSIDE DIAMETER AT TERMINAL END NONE. 1D AND 1B MODE REPLY11AA05 AAFPJ /D/ 04DIAMETER AT BRUSH END,OUTSIDE,SPRING SPRING OUTSIDE DIAMETER AT BRUSH END NONE. 1D AND 1B MODE REPLY11AA05 AAFQJ /D/ 04LENGTH,FREE,SPRING SPRING FREE LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AAFRJ /D/ 04LENGTH,COMPRESSED,SPRING SPRING COMPRESSED LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AAFSD 02DESIGN,APPLICATION APPLICATION DESIGN THE PRIMARY APPLICATION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AA25 AAFTD /D/ 02DESIGN,BASE BASE DESIGN THE DESIGN TYPE OF THE BASE MOUNTING FACILITY OF A SOLID RUBBER TIRE. SELECT REPLY CODE 10AA26 AAFUD 03DESIGNATION,SIZE SIZE DESIGNATION THE SIZE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND DESIGNATED. SELECT REPLY CODE 10AA27 AAFVA 10PLY RATING PLY RATING THE NUMERIC TERM PLY RATING IS USED AS AN INDEX OF STRENGTH AND DOES NOT NECESSARILY REPRESENT THE ACTUAL NUMBER OF CORD PLIES IN THE TIRE. 1A MODE REPLY 0 AAFWA 12QUANTITY,PLY PLY QUANTITY THE ACTUAL NUMBER OF FULL LAYERS OF MATERIAL. 1A MODE REPLY 0 AAFXD /D/ 19ARRANGEMENT,PLY PLY ARRANGEMENT THE ANGLE WHICH THE PLIES ARE LAID IN RELATIONSHIP TO THE CIRCUMFERENTIAL CENTERLINE OF THE TIRE. SELECT REPLY CODE 10AA28 AAFYD /D/ 09MATERIAL,CORD CORD MATERIAL THE MATERIAL OF THE CORD USED TO FORTIFY THE TIRE CONSTRUCTION. SELECT REPLY CODE 10AD09 AAFZD /D/ 09MATERIAL,BODY BODY MATERIAL THE BASIC MATERIAL OF WHICH THE BODY IS FABRICATED. PLEASE USE MATT AND ISACTHE BODY REPLY IN PLACE OF THIS DISCONTINUED MRC SELECT REPLY CODE 10AD09 AAGAD 10RESISTANCE,OZONE OZONE RESISTANCE THE PRESENCE OF A TREATMENT COMPOUNDED INTO,OR APPLIED TO,AN ITEM TO PREVENT CHECKING OR CRACKING OF THE SURFACE DUE TO OZONE PRESENCE. SELECT REPLY CODE 10AA29 AAGBF /D/T10RANGE IN DEG CELSIUS,TEMP,OPERATING OPERATING TEMP RANGE IN DEG CELSIUS THE MINIMUM AND MAXIMUM OPERATING TEMPERATURES AT WHICH THE ITEM IS RATED,EXPRESSED IN DEGREES CELSIUS. 1F MODE REPLY 0 AAGCD 19PATTERN,TREAD TREAD PATTERN THE DESIGN MOLDED INTO THE TIRE TREAD RUBBER TO PROVIDE TRACTION. SELECT REPLY CODE 10AA30 AAGDD /D/ 18TYPE,GRIP,ICE ICE GRIP TYPE INDICATES THE TYPE OF FEATURES BUILT INTO THE TIRE TREAD TO INCREASE TRACTION ON ICY SURFACES. SELECT REPLY CODE 10AA39 AAGED /D/ 11METHOD,RETENTION,AIR AIR RETENTION METHOD THE MEANS USED TO RETAIN AIR INSIDE THE ITEM. SELECT REPLY CODE 10AA32 AAGFD /D/ 11METHOD,MOUNTING MOUNTING METHOD THE MEANS USED TO MOUNT SOLID RUBBER TIRES ON A RIM. SELECT REPLY CODE 10AA33 AAGGA 12QUANTITY,LUG LUG QUANTITY THE NUMBER OF LUGS REQUIRED. 1A MODE REPLY 0 AAGHJ /D/ 04HEIGHT,LUG LUG HEIGHT THE VERTICAL MEASUREMENT OF EACH LUG. 1D AND 1B MODE REPLY11AA05 AAGJJ /D/ 04SPACING,LUG LUG SPACING THE CENTER TO CENTER DISTANCE FROM ONE LUG TO ANOTHER MEASURED CIRCUMFERENTIALLY. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 1D AND 1B MODE REPLY11AA05 AAGKJ 10SPEED,RATED RATED SPEED THE RATED SPEED FOR WHICH THE ITEM HAS BEEN TESTED FOR PERFORMANCE. 1D AND 1B MODE REPLY11AA34 AAGLJ 10PRESSURE,INFLATION,MAXIMUM MAXIMUM INFLATION PRESSURE THE MAXIMUM INFLATION PRESSURE FOR WHICH THE ITEM HAS BEEN RATED. 1D AND 1B MODE REPLY11AB18 AAGMJ /D/ 10RATING,LOAD,STATIC,MAXIMUM MAXIMUM STATIC LOAD RATING THE MAXIMUM RATED LOAD APPLIED TO AN ITEM AT MAXIMUM INFLATION PRESSURE. 1D AND 1B MODE REPLY12AB16 AAGNJ 04SIZE DESIGNATION,PIPE,NOMINAL NOMINAL PIPE SIZE DESIGNATION THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE DIAMETER OF PIPE. 1D AND 1B MODE REPLY11AA05 AAGPD 03DESIGNATION,THICKNESS,WALL WALL THICKNESS DESIGNATION THE TERM USED TO DEFINE THE WALL THICKNESS CROSS-SECTIONAL DIMENSIONS OF PIPE OF VARIOUS MATERIAL AS REPRESENTED BY A SCHEDULE,THICKNESS CLASS,CLASS,STRENGTH,OR WEIGHT DESIGNATION. SELECT REPLY CODE 10AA35 AAGQJ /D/ 11METHOD AND LENGTH,MEASURING MEASURING METHOD AND LENGTH THE MEANS USED AND THE MEASUREMENT OF THE LONGEST DIMENSION WHICH ESTABLISHES THE ACCEPTABLE LENGTH OF THE ITEM. 3D AND 1B MODE REPLY31AC241AA051AC20 AAGRL 16STYLE,SHAPE,CROSS-SECTIONAL CROSS-SECTIONAL SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE CROSS-SECTIONAL SHAPE OF THE ITEM. 1L MODE REPLY 0 AAGSD /D/ 07INDICATOR,PROCESSED FOR REFRIGERATION SERVICE PROCESSED FOR REFRIGERATION SERVICE INDICATOR THE TERMINOLOGY WHICH INDICATES THAT THE ITEM HAS BEEN CLEANED AND THE ENDS ARE SEALED TO PREVENT THE ENTRANCE OF CONTAMINANTS DURING SHIPPING, STORAGE, AND HANDLING. SELECT REPLY CODE 10AA36 AAGTJ 04THICKNESS,WALL WALL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE WALL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AAGUJ /D/ 04DEPTH,LIP LIP DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAGVJ /D/ 04DEPTH,FLUTE FLUTE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAGWJ 04WIDTH ACROSS FLATS WIDTH ACROSS FLATS THE SHORTEST STRAIGHT LINE BETWEEN THE FLATS OF A HEXAGONAL OR OCTAGONAL CROSS-SECTIONAL PLANE WHICH IS PERPENDICULAR TO THE HEIGHT. 1D AND 1B MODE REPLY11AA05 AAGXJ 04WIDTH,END,LARGEST LARGEST END WIDTH THE LARGEST END MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AAGYJ 04WIDTH,END,SMALLEST SMALLEST END WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SMALLEST END,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AAGZL 16STYLE,END,FIRST FIRST END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FIRST END. 1L MODE REPLY 0 AAHAJ 04DIAMETER,INSIDE,FIRST END FIRST END INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHBJ 04DIAMETER,OUTSIDE,FIRST END FIRST END OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHCJ 04LENGTH,TELESCOPING,FIRST END FIRST END TELESCOPING LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHDJ 04DIAMETER,OUTSIDE,FIRST END BEAD FIRST END BEAD OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHEJ 04LENGTH,FLARE,FIRST END FIRST END FLARE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHFJ 04DIAMETER,OUTSIDE,FIRST END FLANGE FIRST END FLANGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHGJ 04WIDTH,GROOVE,FIRST END FIRST END GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHHJ 04DIAMETER,GROOVE,FIRST END FIRST END GROOVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHJJ 04LENGTH FROM GROOVE TO END,FIRST END FIRST END LENGTH FROM GROOVE TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHKJ 04WIDTH,BEAD,FIRST END FIRST END BEAD WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHLJ 04LENGTH,UNDERCUT,FIRST END FIRST END UNDERCUT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHMJ /D/ 04LENGTH FROM BEAD CENTER TO END,FIRST END FIRST END LENGTH FROM BEAD CENTER TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHND 19SIMILARITY,END END SIMILARITY A TERM USED TO IDENTIFY THE ENDS AS IDENTICAL OR NOT IDENTICAL. SELECT REPLY CODE 10AA37 AAHPL 16STYLE,END,SECOND SECOND END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SECOND END. 1L MODE REPLY 0 AAHQJ 04DIAMETER,INSIDE,SECOND END SECOND END INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHRJ 04DIAMETER,OUTSIDE,SECOND END SECOND END OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHSJ 04LENGTH,TELESCOPING,SECOND END SECOND END TELESCOPING LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHTJ 04DIAMETER,OUTSIDE,SECOND END BEAD SECOND END BEAD OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHUJ 04LENGTH,FLARE,SECOND END SECOND END FLARE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHVJ 04DIAMETER,OUTSIDE,SECOND END FLANGE SECOND END FLANGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHWJ 04WIDTH,GROOVE,SECOND END SECOND END GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHXJ 04DIAMETER,GROOVE,SECOND END SECOND END GROOVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHYJ 04LENGTH FROM GROOVE TO END,SECOND END SECOND END LENGTH FROM GROOVE TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AAHZJ 04WIDTH,BEAD,SECOND END SECOND END BEAD WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAJAJ 04LENGTH,UNDERCUT,SECOND END SECOND END UNDERCUT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAJBJ 04LENGTH FROM BEAD CENTER TO END,SECOND END SECOND END LENGTH FROM BEAD CENTER TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AAJCJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. PLEASE USE MRC THDS IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1A MODE REPLY12AC21 AAJDA 13THREAD CLASS THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD. 1A MODE REPLY 0 AAJEJ T04THREAD PITCH DIAMETERS THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 AAJFD 13THREAD DIRECTION THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 AAJGD /D/ 19CONSTRUCTION CONSTRUCTION THE FORMATION IDENTIFYING THE STRUCTURAL CHARACTERISTIC OF THE ITEM. PLEASE USE MRC CQCF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA39 AAJHD /D/ 11METHOD,WELDING WELDING METHOD THE MEANS BY WHICH THE SEAM IS WELDED. SELECT REPLY CODE 10AA40 AAJJJ /D/ 10PRESSURE,OPERATING,MAXIMUM MAXIMUM OPERATING PRESSURE THE MAXIMUM PRESSURE AT WHICH AN ITEM IS DESIGNED TO OPERATE. PLEASE USE MRC CQQF IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1B MODE REPLY11AB18 AAJKB 10TEMP IN DEG CELSIUS,OPERATING,MAXIMUM MAXIMUM OPERATING TEMP IN DEG CELSIUS THE MAXIMUM OPERATING TEMPERATURE AT WHICH THE ITEM IS RATED,EXPRESSED IN DEGREES CELSIUS. 1B MODE REPLY 0 AAJLD /D/ 14SHAPE,WIRE,ACCOMMODATED CONDUCTOR ACCOMMODATED CONDUCTOR WIRE SHAPE THE PHYSICAL CONFIGURATION OF THE CONDUCTOR WIRE THE ITEM IS DESIGNED TO ACCOMMODATE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. SELECT REPLY CODE 10AD07 AAJMD /D/ 19FINISH,SURFACE,INSIDE INSIDE SURFACE FINISH AN ADDITIONAL FINISHING PROCESS BY WHICH THE INSIDE SURFACE OF AN ITEM IS ALTERED IN RESPECT TO POLISHING, GRINDING AND THE LIKE. SELECT REPLY CODE 10AA41 AAJND /D/ 19FINISH,SURFACE,OUTSIDE OUTSIDE SURFACE FINISH AN ADDITIONAL FINISHING PROCESS BY WHICH THE OUTSIDE SURFACE OF AN ITEM IS ALTERED IN RESPECT TO POLISHING,GRINDING,AND THE LIKE. PLEASE USE MRC AGYE IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA41 AAJPD /D/ 17SURFACE TREATMENT,OUTSIDE OUTSIDE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE OUTSIDE SURFACE. PLEASE USE MRC SFTT WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AAJQD /D/ 17SURFACE TREATMENT,INSIDE INSIDE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE INSIDE SURFACE. SELECT REPLY CODE 10AD09 AAJRD /D/ 19DEVICES,PROTECTIVE,THREAD THREAD PROTECTIVE DEVICES AN ITEM APPLIED TO THE THREADED END OF AN ITEM TO GUARD AGAINST DAMAGE DURING SHIPPING,STORAGE,AND HANDLING. SELECT REPLY CODE 10AA42 AAJSD 19CONFIGURATION,DESIGN DESIGN CONFIGURATION THE BASIC SHAPE,APPLICATION AND SURFACE FEATURES,AND THE LIKE,OF THE ITEM. SELECT REPLY CODE 10AA43 AAJTJ 04HEIGHT,OVERALL OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM. 1D AND 1B MODE REPLY11AA05 AAJUJ 04LENGTH,OVERALL OVERALL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AAJVJ 04WIDTH,OVERALL OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AAJWJ 04DIAMETER,OVERALL OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE. 1D AND 1B MODE REPLY11AA05 AAJXJ 04THICKNESS,MATERIAL MATERIAL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE MATERIAL STOCK FOR STAMPED OR FORMED ITEMS,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 AAJYJ /D/ 04DIAMETER,CAP CAP DIAMETER THE DISTANCE ACROSS THE CIRCULAR PORTION OF THE CAP. 1D AND 1B MODE REPLY11AA05 AAJZJ 04DISTANCE BETWEEN FIRST AND SECOND POSTS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FIRST AND SECOND POSTS NONE. 1D AND 1B MODE REPLY11AA05 AAKAJ 04HEIGHT ABOVE MOUNTING SURFACE,MAXIMUM MAXIMUM HEIGHT ABOVE MOUNTING SURFACE DISTANCE FROM SURFACE PLANE OF MOUNTING TO TOP OF ITEM. 1D AND 1B MODE REPLY11AA05 AAKBJ 04DIAMETER,THRU-HOLE THRU-HOLE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AAKCJ /D/ 04LENGTH,INSULATOR INSULATOR LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AAKDB 04TAPER PER INCH IN INCHES TAPER PER INCH IN INCHES THE DIMINISHING MEASUREMENT OF THE DIAMETER ALONG THE MAJOR AXIS OF THE ITEM,EXPRESSED IN INCHES PER INCH. 1B MODE REPLY 0 AAKEJ 04DIAMETER,MINOR,TAPER TAPER MINOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST CIRCULAR CROSS SECTION OF THE TAPERED PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AAKFJ 04LENGTH,TAPER TAPER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TAPERED PORTION OF AN ITEM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AAKGL 16STYLE,DISCONNECT,QUICK QUICK DISCONNECT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE QUICK DISCONNECT. 1L MODE REPLY 0 AAKHJ 04WIDTH,TAB TAB WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AAKJJ 04WIDTH OF TAB ACCOMMODATED WIDTH OF TAB ACCOMMODATED NONE. 1D AND 1B MODE REPLY11AA05 AAKKJ 04DIAMETER,PLUG,MAJOR MAJOR PLUG DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AAKLJ 04DIAMETER ACCOMMODATED,PLUG,MAJOR MAJOR PLUG DIAMETER ACCOMMODATED NONE. 1D AND 1B MODE REPLY11AA05 AAKMJ 04DIAMETER,BALL BALL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BALL,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AAKNJ /D/ 04DIAMETER ACCOMMODATED,BALL BALL DIAMETER ACCOMMODATED NONE. 1D AND 1B MODE REPLY11AA05 AAKPJ 04DIAMETER,PLUG,MINOR MINOR PLUG DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AAKQB /D/ 04TAPER PER METER IN METERS TAPER PER METER IN METERS THE DIMINISHING MEASUREMENT OF THE DIAMETER ALONG THE MAJOR AXIS OF THE ITEM, EXPRESSED IN METERS PER METER. 1B MODE REPLY 0 AAKRL /D/ 16STYLE,POSITION,CONDUCTOR CONDUCTOR POSITION STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE CONDUCTOR POSITION. 1L MODE REPLY 0 AAKSB /D/ 04ANGLE BETWEEN CONDUCTOR ACCOMMODATIONS IN DEG ANGLE BETWEEN CONDUCTOR ACCOMMODATIONS IN DEG NONE. 1B MODE REPLY 0 AAKTA /D/ 16STYLE,ACCOMMODATION,CONDUCTOR CONDUCTOR ACCOMMODATION STYLE THE TYPE OF CONNECTOR OR CONDUCTOR ACCOMMODATION FURNISHED FOR THE PURPOSE OF ATTACHING A WIRE OR CABLE TO AN ITEM. 1A MODE REPLY 0 AAKUA /D/ 12QUANTITY OF WIRES ACCOMMODATED QUANTITY OF WIRES ACCOMMODATED THE NUMBER OF SEPARATE WIRE/S/ AN ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 AAKVJ A04SIZE ACCOMMODATED,CONDUCTOR,MAXIMUM MAXIMUM CONDUCTOR SIZE ACCOMMODATED THE MAXIMUM SIZE OF THE CONDUCTOR THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1A MODE REPLY11AA44 AAKWD 19CONSTRUCTION,WIRE,ACCOMMODATED CONDUCTOR ACCOMMODATED CONDUCTOR WIRE CONSTRUCTION THE CONSTRUCTION OF THE CONDUCTOR WIRE THE ITEM IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AA45 AAKXD /D/ 18TYPE,WIRE,CONDUCTOR,ACCOMMODATED ACCOMMODATED CONDUCTOR WIRE TYPE INDICATES THE TYPE OF CONDUCTOR WIRE THE ITEM IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AA46 AAKYD /D/ 09MATERIAL,CONDUCTOR ACCOMMODATION CONDUCTOR ACCOMMODATION MATERIAL THE COMPOSITION OF WHICH THE CONDUCTOR ACCOMMODATION IS MANUFACTURED. SELECT REPLY CODE 10AD09 AAKZD /D/ 17SURFACE TREATMENT,CONDUCTOR ACCOMMODATION CONDUCTOR ACCOMMODATION SURFACE TREATMENT THE COATING, DIP, OR PLATING APPLIED TO THE CONDUCTOR ACCOMMODATION FOR ENVIRONMENTAL PROTECTION OR INCREASED ELECTRICAL CONDUCTIVITY. SELECT REPLY CODE 10AD09 AALAJ 04DIAMETER,LARGEST LARGEST DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE LARGEST CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AALBJ 04WIDTH,LARGEST LARGEST WIDTH THE LARGEST MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ITEM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AALCJ 04LENGTH,BOLT BOLT LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AALDJ 04DIAMETER,MINOR,TURRET TURRET MINOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AALEJ /D/ 04DISTANCE BETWEEN MOUNTING AND FIRST TURRET DISTANCE BETWEEN MOUNTING AND FIRST TURRET NONE. 1D AND 1B MODE REPLY11AA05 AALFJ /D/ 04DISTANCE BETWEEN FIRST AND SECOND TURRET DISTANCE BETWEEN FIRST AND SECOND TURRET NONE. 1D AND 1B MODE REPLY11AA05 AALGJ /D/ 04DISTANCE BETWEEN SECOND AND THIRD TURRET DISTANCE BETWEEN SECOND AND THIRD TURRET NONE. 1D AND 1B MODE REPLY11AA05 AALHJ /D/ 04DISTANCE BETWEEN THIRD AND FOURTH TURRET DISTANCE BETWEEN THIRD AND FOURTH TURRET NONE. 1D AND 1B MODE REPLY11AA05 AALJJ 04DISTANCE BETWEEN TURRETS DISTANCE BETWEEN TURRETS NONE. 1D AND 1B MODE REPLY11AA05 AALKJ /D/ 13THREAD LENGTH,TERMINAL TERMINAL THREAD LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AALLJ 04DIAMETER,HOLE,WIRE WIRE HOLE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AALMJ /D/ 04WIDTH,HOLE,WIRE WIRE HOLE WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AALNJ /D/ 04WIDTH ACROSS FLATS OF ADJUSTING NUT WIDTH ACROSS FLATS OF ADJUSTING NUT NONE. 1D AND 1B MODE REPLY11AA05 AALPA /D/ 13THREAD DIAMETER NUMERIC DESIGNATOR,TERMINAL TERMINAL THREAD DIAMETER NUMERIC DESIGNATOR NONE. 1A MODE REPLY 0 AALQJ /D/ 13THREAD SIZE,TERMINAL TERMINAL THREAD SIZE NONE. 1D AND 1B MODE REPLY11AA05 AALRD /D/ 13THREAD SERIES,TERMINAL TERMINAL THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A THREADED TERMINAL. SELECT REPLY CODE 10AC21 AALSB /D/ 04TAPER PER INCH IN INCHES,RECESS RECESS TAPER PER INCH IN INCHES NONE. 1B MODE REPLY 0 AALTB /D/ 04TAPER PER METER IN METERS,RECESS RECESS TAPER PER METER IN METERS NONE. 1B MODE REPLY 0 AALUB /D/ 04ANGLE IN DEG,CONDUCTOR ACCOMMODATION CONDUCTOR ACCOMMODATION ANGLE IN DEG NONE. 1B MODE REPLY 0 AALVD 19FEATURE,INSULATION,ELECTRICAL ELECTRICAL INSULATION FEATURE THE FEATURE CONSISTING OF SLEEVES,COVERING,CAPS,MOUNTING BUSHINGS AND THE LIKE,USED TO ELECTRICALLY INSULATE AN ITEM. SELECT REPLY CODE 10AA47 AALWD /D/ 09MATERIAL,INSULATION INSULATION MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INSULATION IS FABRICATED. SELECT REPLY CODE 10AD09 AALXL 16STYLE,METHOD,MOUNTING MOUNTING METHOD STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE MOUNTING METHOD OF THE ITEM. 1L MODE REPLY 0 AALYD /D/ 09MATERIAL,MOUNTING MOUNTING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MOUNTING IS FABRICATED. PLEASE USE MRC MATT WITH ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AALZD /D/ 17SURFACE TREATMENT,MOUNTING MOUNTING SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE MOUNTING SURFACE. PLEASE USE MRC SFTTIN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AAMAJ 04DIAMETER,HOLE,MOUNTING MOUNTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AAMBJ 04WIDTH,HOLE,MOUNTING MOUNTING HOLE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING HOLE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AAMCJ 04WIDTH,TONGUE,MOUNTING MOUNTING TONGUE WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AAMDJ /D/ 04DISTANCE FROM CENTER OF MOUNTING HOLE TO END OF MOUNTING DISTANCE FROM CENTER OF MOUNTING HOLE TO END OF MOUNTING NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 1D AND 1B MODE REPLY11AA05 AAMEJ /D/ 04DEPTH,SLOT,MOUNTING MOUNTING SLOT DEPTH NONE. 1D AND 1B MODE REPLY11AA05 AAMFJ /D/ 13THREAD LENGTH,MOUNTING MOUNTING THREAD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE THREADED PORTION OF THE MOUNTING FACILITY, IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AAMGJ /D/ 04DISTANCE BETWEEN MOUNTING HOLE CENTERS DISTANCE BETWEEN MOUNTING HOLE CENTERS A MEASUREMENT OF THE DISTANCE BETWEEN THE MOUNTING HOLE CENTERLINES. 2D AND 1B MODE REPLY21AA051AC20 AAMHJ /D/ 04DISTANCE BETWEEN MOUNTING HOLE CENTERS,LATERAL LATERAL DISTANCE BETWEEN MOUNTING HOLE CENTERS NONE. 1D AND 1B MODE REPLY11AA05 AAMJJ /D/ 04DISTANCE BETWEEN MOUNTING STUD CENTERS DISTANCE BETWEEN MOUNTING STUD CENTERS NONE. 1D AND 1B MODE REPLY11AA05 AAMKJ 04THICKNESS,FACILITY,MOUNTING MOUNTING FACILITY THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE MOUNTING FACILITY,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 AAMLJ 04DIAMETER,MAJOR,TAPERED MOUNTING TAPERED MOUNTING MAJOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AAMMJ 04DIAMETER,MINOR,TAPERED MOUNTING TAPERED MOUNTING MINOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AAMNA /D/ 13THREAD DIAMETER NUMERIC DISIGNATOR,MOUNTING MOUNTING THREAD DIAMETER NUMERIC DISIGNATOR NONE. 1A MODE REPLY 0 AAMPJ 13THREAD DIAMETER,MOUNTING MOUNTING THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED MOUNTING,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AAMQA 13THREADS PER INCH,MOUNTING MOUNTING THREADS PER INCH THE NUMBER OF THREADS PER INCH ON THE MOUNTING. 1A MODE REPLY 0 AAMRD /D/ 13THREAD SERIES,MOUNTING MOUNTING THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A THREADED MOUNTING. SELECT REPLY CODE 10AC21 AAMSJ 04DIAMETER,BUSHING,MINOR MINOR BUSHING DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AAMTJ 04DIAMETER,BUSHING,MAJOR MAJOR BUSHING DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AAMUJ 04LENGTH,BUSHING,MINOR MINOR BUSHING LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AAMVJ 04LENGTH,BUSHING,MAJOR MAJOR BUSHING LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AAMWJ 04DIAMETER,FLANGE FLANGE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FLANGE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AAMXJ 04DEPTH,SWAGE SWAGE DEPTH NONE. 1D AND 1B MODE REPLY11AA05 AAMYJ /D/ 04DIAMETER,INSIDE,SWAGE SWAGE INSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AAMZJ 04DIAMETER,OUTSIDE,SWAGE SWAGE OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AANAJ 04WIDTH ACROSS FLATS,BUSHING,THREADED THREADED BUSHING WIDTH ACROSS FLATS NONE. 1D AND 1B MODE REPLY11AA05 AANBB /D/ 04ANGLE IN DEG,SWAGE SWAGE ANGLE IN DEG NONE. 1B MODE REPLY 0 AANCL /D/ 16STYLE,FEATURE,NONTURN NONTURN FEATURE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE NONTURN FEATURE ON THE ITEM. 1L MODE REPLY 0 AANDJ /D/ 04WIDTH ACROSS FLATTED PORTION WIDTH ACROSS FLATTED PORTION A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FLATTED PORTION, IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AANEJ /D/ 04DIAMETER,PIN OR HOLE,DOWEL DOWEL PIN OR HOLE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AANFJ /D/ 04DISTANCE BETWEEN DOWEL PIN OR HOLE AND MOUNTING FACILITY CENTERS DISTANCE BETWEEN DOWEL PIN OR HOLE AND MOUNTING FACILITY CENTERS NONE. 1D AND 1B MODE REPLY11AA05 AANGJ /D/ 04DISTANCE BETWEEN CENTER OF MOUNTING FACILITY AND END OF KEY DISTANCE BETWEEN CENTER OF MOUNTING FACILITY AND END OF KEY NONE. 1D AND 1B MODE REPLY11AA05 AANHJ /D/ 04WIDTH,LIP LIP WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AANJJ /D/ 04THICKNESS,LIP LIP THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 AANKD /D/ 11METHOD,SUPPORT,INSULATION INSULATION SUPPORT METHOD THE MEANS PROVIDED WITH THE CONDUCTOR ACCOMMODATION FACILITY FOR SUPPORTING THE WIRE INSULATION. SELECT REPLY CODE 10AA48 AANLJ 04DIAMETER ACCOMMODATED,INSULATION,MAXIMUM MAXIMUM INSULATION DIAMETER ACCOMMODATED THE MAXIMUM DIAMETER OF INSULATION ACCOMMODATED. 1D AND 1B MODE REPLY11AA05 AANMD /D/ 19CONDUCTOR ACCOMMODATION,FILLED,COMPOUND COMPOUND FILLED CONDUCTOR ACCOMMODATION INDICATES WHETHER OR NOT THE CONDUCTOR ACCOMMODATION PORTION IS PREFILLED WITH A SPECIAL ABRASIVE MIXTURE DESIGNED TO INCREASE JUNCTION ELECTRICAL RELIABILITY. SELECT REPLY CODE 10AA89 AANND /D/ 19PLUG,INSPECTION,CONDUCTOR ACCOMMODATION CONDUCTOR ACCOMMODATION INSPECTION PLUG INDICATES WHETHER OR NOT AN INSPECTION PLUG IS INCLUDED. SELECT REPLY CODE 10AN33 AANPD /D/ 07DEVICE,PIERCING,INSULATION INSULATION PIERCING DEVICE INDICATES WHETHER OR NOT THE ITEM IS PROVIDED WITH A SPECIAL DEVICE TO PIERCE THE INSULATION OF THE WIRE/CABLE THE ITEM ACCOMMODATES AND THUS ELIMINATES THE NECESSITY OF STRIPPING THE INSULATION. SELECT REPLY CODE 10AB22 AANQD /D/ 07FEATURE,ACTION,SWIVEL,CONDUCTOR ACCOMMODATION CONDUCTOR ACCOMMODATION SWIVEL ACTION FEATURE INDICATES WHETHER OR NOT THE CONDUCTOR ACCOMMODATION FEATURES A SPECIAL SWIVELING ACTION TO FACILITATE CONDUCTOR ACCEPTANCE FROM ONE OF SEVERAL DIRECTIONS. SELECT REPLY CODE 10AA49 AANRD /D/ 05DIRECTION,ANGULAR,CONDUCTOR ACCOMMODATION CONDUCTOR ACCOMMODATION ANGULAR DIRECTION THE ANGULAR DIRECTION OF THE CONDUCTOR ACCOMMODATION IN RELATION TO THE MOUNTING FACILITY. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. SELECT REPLY CODE 10AA50 AANSD /D/ 05DIRECTION,OFFSET,CONDUCTOR ACCOMMODATION CONDUCTOR ACCOMMODATION OFFSET DIRECTION THE DIRECTION THAT THE CONDUCTOR ACCOMMODATION IS OFFSET WITH RESPECT TO ITS PARALLEL MOUNTING FACILITY. SELECT REPLY CODE 10AA51 AANTB /D/ 04ANGLE BETWEEN MOUNTING FACILITY AND CONDUCTOR ACCOMMODATION CENTERLINES IN DEGREES ANGLE BETWEEN MOUNTING FACILITY AND CONDUCTOR ACCOMMODATION CENTERLINES IN DEGREES NONE. 1B MODE REPLY 0 AANUJ /D/ 04DISTANCE BETWEEN BOTTOM OF MOUNTING FACILITY AND CENTERLINE OF CONDUCTOR ACCOMMODATION,OFFSET OFFSET DISTANCE BETWEEN BOTTOM OF MOUNTING FACILITY AND CENTERLINE OF CONDUCTOR ACCOMMODATION NONE. 1D AND 1B MODE REPLY11AA05 AANVD /D/ 19CONDITION,SURFACE SURFACE CONDITION THE SURFACE CONDITION OF A BINDING POST CAP WITH RESPECT TO THE TEXTURE OF THE GRIPPING SURFACE. SELECT REPLY CODE 10AB32 AANWD /D/ 07REMOVABILITY,CAP CAP REMOVABILITY AN INDICATION OF WHETHER OR NOT THE CAP IS REMOVABLE. SELECT REPLY CODE 10AC29 AANXD /D/ 11METHOD,ACTION,CAP CAP ACTION METHOD INDICATES WHETHER THE TYPE OF CAP ACTION IS SCREW TYPE OR SPRING TYPE. SELECT REPLY CODE 10AA52 AANYD /D/ 18TYPE,JACK,TIP TIP JACK TYPE INDICATES THE TYPE OF TIP JACK PROVIDED ON THE ITEM. SELECT REPLY CODE 10AA53 AANZD /D/ 19FEATURE,TERMINAL,ADDITIONAL ADDITIONAL TERMINAL FEATURE AN INDICATION OF ANY ADDITIONAL FEATURE INCLUDED WITH THE TERMINAL. SELECT REPLY CODE 10AA54 AAPAB 10VOLTAGE RATING IN VOLTS,FLASHOVER,DRY DRY FLASHOVER VOLTAGE RATING IN VOLTS THE ELECTRICAL POTENTIAL WHICH WILL CAUSE A DISRUPTIVE DISCHARGE OVER A DRY INSULATOR,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AAPBB 10VOLTAGE IN VOLTS,WITHSTANDING,DIELECTRIC DIELECTRIC WITHSTANDING VOLTAGE IN VOLTS THE MAXIMUM VOLTAGE THE INSULATING MATERIALS OF THE ITEM WILL WITHSTAND WITHOUT RESULTING IN DISRUPTIVE DISCHARGE OR DETERIORATION,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AAPCD 01COLOR,IDENTIFICATION CODE IDENTIFICATION CODE COLOR THE APPLICATION OF COLOR OR A SERIES OF COLORS FOR THE EXPRESSED PURPOSE OF IDENTIFYING THE SPECIFIC FUNCTIONAL DESIGN AND/OR THE SYSTEM APPLICATION OF AN ITEM. SELECT REPLY CODE 10AD06 AAPDD /D/ 07SEAL,HERMETIC,ELECTRODE ELECTRODE HERMETIC SEAL AN INDICATION OF WHETHER OR NOT THE INSULATION HERMETICALLY SEALS THE ELECTRODE. SELECT REPLY CODE 10AB22 AAPEF T10COEFFICIENT OF RESISTANCE IN PPM PER DEG CELSIUS,TEMP TEMP COEFFICIENT OF RESISTANCE IN PPM PER DEG CELSIUS A CONSTANT THAT REPRESENTS THE PROPORTIONATE CHANGE IN RESISTANCE CAUSED BY A CHANGE IN TEMPERATURE,EXPRESSED IN PARTS PER MILLION CHANGE PER DEGREE CELSIUS. 1F MODE REPLY 0 AAPFD /D/ 07HARDWARE,MOUNTING MOUNTING HARDWARE AN INDICATION OF WHETHER OR NOT MOUNTING HARDWARE IS FURNISHED. SELECT REPLY CODE 10AA55 AAPGB /D/ 10RATING IN AMPS,CURRENT,RISE,TEMP TEMP RISE CURRENT RATING IN AMPS THE RATED ELECTRICAL CURRENT THE ITEM IS DESIGNED TO CARRY WITH A TEMPERATURE RISE OF NOT MORE THAN 5 DEGREES CELSIUS ABOVE THAT OF THE CABLES TO WHICH THEY ARE CONNECTED, EXPRESSED IN AMPERES. 1B MODE REPLY 0 AAPHD /D/ 07FEATURE,WATER-SEAL,CABLE CABLE WATER-SEAL FEATURE INDICATES WHETHER OR NOT THE CABLE IS SEALED TO PREVENT THE ESCAPE OF WATER THROUGH THE CABLE INSULATION WHEN THE ITEM IS PROPERLY INSTALLED, AND THUS MAINTAINS THE INTEGRITY OF WATER-TIGHT COMPARTMENTS. SELECT REPLY CODE 10AB22 AAPJB /D/ 10VOLTAGE DROP IN MILLIVOLTS,MINIMUM MINIMUM VOLTAGE DROP IN MILLIVOLTS THE MINIMUM VOLTAGE DROP OF AN ITEM, EXPRESSED IN MILLIVOLTS. 1B MODE REPLY 0 AAPKB 10RESISTANCE IN MEGOHMS,INSULATION INSULATION RESISTANCE IN MEGOHMS THE OPPOSITION TO THE FLOW OF CURRENT THROUGH AND OVER A NONCONDUCTIVE MATERIAL,EXPRESSED IN MEGOHMS. 1B MODE REPLY 0 AAPLJ 10LOAD RATING,TORQUE TORQUE LOAD RATING THE ABILITY OF AN ITEM TO WITHSTAND A SPECIFIED TORQUE LOAD WITHOUT FRACTURE. 1D AND 1B MODE REPLY11AA56 AAPMB 10STRENGTH IN POUNDS,TENSILE TENSILE STRENGTH IN POUNDS THE GREATEST LONGITUDINAL STRESS AN ITEM CAN BEAR WITHOUT TEARING APART,EXPRESSED IN POUNDS. 1B MODE REPLY 0 AAPNA 12QUANTITY,SECTION SECTION QUANTITY THE NUMBER OF INDIVIDUAL ELEMENTS. 1A MODE REPLY 0 AAPPJ 10RESISTANCE,ELECTRICAL ELECTRICAL RESISTANCE A MEASURE OF THE OPPOSITION TO THE FLOW OF ELECTRICAL CURRENT. 1D AND 1B MODE REPLY11AA57 AAPQF T10TOLERANCE IN PERCENT,RESISTANCE RESISTANCE TOLERANCE IN PERCENT THE LIMITS OF PERMISSIBLE VARIATION IN THE ELECTRICAL RESISTANCE VALUE OF AN ITEM FROM ITS RATED VALUE,EXPRESSED IN PERCENT. 1F MODE REPLY 0 AAPRA 12QUANTITY,TAP,FIXED FIXED TAP QUANTITY THE NUMBER OF FIXED TERMINALS AT POINTS BETWEEN THE END TERMINALS THAT PROVIDE CONNECTION TO INTERMEDIATE VALUES OF THE TOTAL VALUE. 1A MODE REPLY 0 AAPSD /D/ 16STYLE,TERMINAL,TAP,FIXED FIXED TAP TERMINAL STYLE THE SPECIFIC STYLE OF FIXED TERMINALS AT POINTS BETWEEN THE END TERMINALS THAT PROVIDE CONNECTION TO INTERMEDIATE VALUES OF THE TOTAL VALUE. SELECT REPLY CODE 10AA58 AAPTJ /D/ 10RESISTANCE,SEGMENT SEGMENT RESISTANCE THE OPPOSITION OF THE FLOW OF ELECTRIC CURRENT THROUGH EACH SEGMENT. 1D AND 1B MODE REPLY11AA57 AAPUF /D/T10TOLERANCE IN PERCENT,RESISTANCE,SEGMENT SEGMENT RESISTANCE TOLERANCE IN PERCENT THE LIMITS OF PERMISSIBLE VARIATION IN THE ELECTRICAL RESISTANCE VALUE FROM THE RATED VALUE OF THE SEGMENT, EXPRESSED IN PERCENT. 1F MODE REPLY 0 AAPVA /D/ 12QUANTITY,TAP,ADJUSTABLE ADJUSTABLE TAP QUANTITY THE NUMBER OF MANUALLY POSITIONED TERMINALS (BANDS, CLAMPS, LUGS, AND THE LIKE), INCLUDING SLIDES, POSITIONED AT POINTS BETWEEN THE END TERMINALS TO PROVIDE CONNECTION TO INTERMEDIATE VALUES OF THE TOTAL VALUE. 1A MODE REPLY 0 AAPWD /D/ 16STYLE,TERMINAL,TAP,ADJUSTABLE ADJUSTABLE TAP TERMINAL STYLE THE SPECIFIC STYLES OF MANUALLY POSITIONED TERMINALS (BANDS, CLAMPS, LUGS, AND THE LIKE), INCLUDING SLIDES, POSITIONED AT POINTS BETWEEN THE END TERMINALS TO PROVIDE CONNECTION TO INTERMEDIATE VALUES OF THE TOTAL VALUE. SELECT REPLY CODE 10AA58 AAPXB /D/ 10DISSIPATION IN WATTS,POWER,AIR,FREE FREE AIR POWER DISSIPATION IN WATTS THE MINIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY AN ITEM WITHOUT BEING MOUNTED ON A CHASSIS, METAL PLATE, OR OTHER HEAT SINK, EXPRESSED IN WATTS. 1B MODE REPLY 0 AAPYB /D/ 10DISSIPATION RATING IN WATTS ON HEAT SINK,POWER POWER DISSIPATION RATING IN WATTS ON HEAT SINK THE MAXIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY AN ITEM WHEN MOUNTED ON A CHASSIS, METAL PLATE, OR OTHER HEAT SINK, EXPRESSED IN WATTS. 1B MODE REPLY 0 AAPZD /D/ 09MATERIAL,SINK,HEAT HEAT SINK MATERIAL THE SUBSTANCE OF WHICH THE HEAT SINK IS COMPOSED. USE MRC MATT WITH ISAC CODING 2AA FROM ISAC TABLE 0013. SELECT REPLY CODE 10AD09 AAQAJ 04LENGTH,HEAT SINK HEAT SINK LENGTH THE LARGEST DIMENSION OF A FLAT RECTANGULAR/ELLIPTICAL,OR A CHASSIS TYPE OF HEAT SINK. 1D AND 1B MODE REPLY11AA05 AAQBJ 04WIDTH,HEAT SINK HEAT SINK WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A FLAT RECTANGULAR/ELLIPTICAL,OR CHASSIS TYPE HEAT SINK,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AAQCJ 04DIAMETER,HEAT SINK HEAT SINK DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FLAT DISK TYPE HEAT SINK,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AAQDJ 04HEIGHT,HEAT SINK HEAT SINK HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A CHASSIS TYPE HEAT SINK,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 AAQEJ 04THICKNESS,HEAT SINK HEAT SINK THICKNESS A MEASUREMENT OF THE SMALLEST PHYSICAL DIMENSION OF A HEAT SINK,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 AAQFB /D/ 10TEMP IN DEG CELSIUS AT FULL RATED POWER,AMBIENT AMBIENT TEMP IN DEG CELSIUS AT FULL RATED POWER THE AMBIENT TEMPERATURE OF THE MEDIUM SURROUNDING AN ITEM AT WHICH IT CAN BE OPERATED CONTINUOUSLY AT FULL RATED POWER,EXPRESSED IN DEGREES CELSIUS.PLEASE USE MRC AEHY IN PLACE OF THIS DISCONTINUED MRC. 1B MODE REPLY 0 AAQGB 10TEMP IN DEG CELSIUS AT ZERO PERCENT RATED POWER,AMBIENT AMBIENT TEMP IN DEG CELSIUS AT ZERO PERCENT RATED POWER THE AMBIENT TEMPERATURE AT WHICH THE POWER DISSIPATION OF AN ITEM IS OPERATED TO ZERO PERCENT OF THE FULL RATED POWER,EXPRESSED IN DEGREES CELSIUS. 1B MODE REPLY 0 AAQHF T10RANGE OF TEMP COEFFICIENT IN DEG CELSIUS,TEMP TEMP RANGE OF TEMP COEFFICIENT IN DEG CELSIUS THE MAXIMUM AND MINIMUM TEMPERATURES TO WHICH THE TEMPERATURE COEFFICIENT APPLIES,EXPRESSED IN DEGREES CELSIUS. 1F MODE REPLY 0 AAQJJ /D/ 04DISTANCE BETWEEN SECOND AND THIRD POSTS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SECOND AND THIRD POSTS NONE. 1D AND 1B MODE REPLY11AA05 AAQKA /D/ 19CODE,CHARACTERISTIC,TEMP,RESISTANCE RESISTANCE TEMP CHARACTERISTIC CODE AN ALPHABETIC LETTER WHICH REPRESENTS THE PERMISSIBLE RANGE OF CHANGES IN RESISTANCE AT SPECIFIED EXTREMES OF TEMPERATURE FROM THE STANDARD RESISTANCE AT THE SPECIFIED STANDARD TEMPERATURE. 1A MODE REPLY 0 AAQLL 16STYLE,BODY BODY STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BODY. 1L MODE REPLY 0 AAQMJ /D/ 04LENGTH,BODY BODY LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AAQNJ /D/ 04DIAMETER,OUTSIDE,BODY BODY OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AAQPJ /D/ 04DIAMETER,INSIDE,BODY BODY INSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AAQQJ /D/ 04WIDTH,BODY BODY WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AAQRJ 04THICKNESS,BODY BODY THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A BODY, IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 AAQSD /D/ 19REMOVABILITY,FACILITIES,MOUNTING MOUNTING FACILITIES REMOVABILITY AN INDICATION OF WHETHER OR NOT THE ITEM HAS A REMOVABLE OR NONREMOVABLE MEANS OF BEING ATTACHED TO A CHASSIS, PANEL, OR ANOTHER ITEM. SELECT REPLY CODE 10AC29 AAQTJ /D/ 04LENGTH,BUSHING,MOUNTING MOUNTING BUSHING LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AAQUJ /D/ 04DISTANCE BETWEEN MOUNTING FACILITY CENTERS DISTANCE BETWEEN MOUNTING FACILITY CENTERS NONE. 1D AND 1B MODE REPLY11AA05 AAQVJ /D/ 04DIAMETER,BUSHING BUSHING DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AAQWJ 04LENGTH,SLOT,MOUNTING MOUNTING SLOT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A MOUNTING SLOT,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AAQXJ 04WIDTH,SLOT,MOUNTING MOUNTING SLOT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A MOUNTING SLOT,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AAQYD /D/ 07INDICATOR,INSULATION,ELECTRICAL ELECTRICAL INSULATION INDICATOR INDICATES WHETHER OR NOT AN ITEM INCLUDES A MATERIAL HAVING A HIGH RESISTANCE, SO PLACED WITH RESPECT TO A CONDUCTOR OR A BODY TO PREVENT EITHER LEAKAGE OF CURRENT OR ADVERSE EXTERNAL ELECTRICAL EFFECTS. SELECT REPLY CODE 10AA89 AAQZD /D/ 11METHOD,INCLOSURE INCLOSURE METHOD THE MEANS PROVIDED TO COAT,COVER,OR PROTECT THE ITEM. PLEASE USE MRC AKNA IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA59 AARAA 12QUANTITY,TERMINAL TERMINAL QUANTITY THE NUMBER OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. 1A MODE REPLY 0 AARBD /D/ 18TYPE,TERMINAL TERMINAL TYPE INDICATES THE TYPE OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. PLEASE USE MRC CSCF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA58 AARCJ /D/ 04HEIGHT FROM BODY,TERMINAL TERMINAL HEIGHT FROM BODY NONE. 1D AND 1B MODE REPLY11AA05 AARDA 12QUANTITY,TERMINAL,DUMMY DUMMY TERMINAL QUANTITY THE NUMBER OF TERMINALS THAT DO NOT PROVIDE ELECTRICAL CONNECTION TO THE ITEM. 1A MODE REPLY 0 AARED 19CHARACTERISTIC,REACTANCE REACTANCE CHARACTERISTIC THE INDUCTIVE OR NONINDUCTIVE CONDITION RESULTING FROM THE METHOD USED IN PLACING /WINDING/ WIRE ON A FORM IN THE CONSTRUCTION OF ELECTRICAL COMPONENTS. SELECT REPLY CODE 10AA60 AARFA 03DESIGNATOR,TYPE,WIRE LEAD,MIL-STD-1276 MIL-STD-1276 WIRE LEAD TYPE DESIGNATOR INDICATES THE TYPE DESIGNATOR,PER MIL-STD-1276,OF THE DETAIL REQUIREMENTS OF LEADS USED ON ELECTRONIC COMPONENTS. 1A MODE REPLY 0 AARGD 07INDICATOR,RELIABILITY RELIABILITY INDICATOR AN INDICATION THAT THE LEVEL OF PROBABILITY THAT AN ITEM WILL OPERATE WITHOUT FAILURE,AT A SPECIFIED RATED CAPABILITY,AT A SPECIFIED TEMPERATURE,AND FOR A SPECIFIED PERIOD OF TIME,HAS BEEN ESTABLISHED BY TESTING RANDOM SAMPLES OF PRODUCTION LOT. SELECT REPLY CODE 10AA61 AARHB 10FAILURE RATE LEVEL IN PERCENT,RELIABILITY RELIABILITY FAILURE RATE LEVEL IN PERCENT THE RATE OF FAILURE DETERMINED UNDER SPECIFIED CONDITIONS TO ESTABLISH THE RELIABILITY OF AN ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 AARJB /D/ 10TIME FACTOR IN HOURS,RELIABILITY RELIABILITY TIME FACTOR IN HOURS THE PERIOD OF TIME INVOLVED IN THE MEASUREMENT OF THE RELIABILITY OF AN ITEM, EXPRESSED IN HOURS. 1B MODE REPLY 0 AARKB /D/ 10FACTOR IN DEG CELSIUS,TEMP,RELIABILITY RELIABILITY TEMP FACTOR IN DEG CELSIUS THE TEMPERATURE SPECIFIED IN THE MEASUREMENT OF THE RELIABILITY OF AN ITEM,EXPRESSED IN DEGREES CELSIUS. 1B MODE REPLY 0 AARLB /D/ 10LEVEL IN PERCENT,CONFIDENCE,RELIABILITY RELIABILITY CONFIDENCE LEVEL IN PERCENT THE DEGREE OF CONFIDENCE THAT CAN BE PLACED IN THE FAILURE RATE LEVEL OF AN ITEM HAVING ESTABLISHED RELIABILITY, EXPRESSED IN PERCENT. 1B MODE REPLY 0 AARMA /D/ 12QUANTITY,LAYER LAYER QUANTITY THE NUMBER OF INDIVIDUAL THICKNESSES LAID OR LYING OVER OR UNDER ONE ANOTHER,REGARDLESS OF THE NUMBER OF PLIES IN EACH LAYER. 1A MODE REPLY 0 AARND 11METHOD,FABRICATION FABRICATION METHOD THE PROCESS USED IN MANUFACTURING THE ITEM. SELECT REPLY CODE 10AA62 AARPJ 10DENSITY,MATERIAL MATERIAL DENSITY A RATING OF THE DENSENESS OR COMPACTNESS OF THE MATERIAL AFTER FABRICATION. 2D AND 1B MODE REPLY21AA631AC20 AARQD 10FLAMMABILITY RATING FLAMMABILITY RATING THE EXTENT TO WHICH THE MATERIAL WILL SUPPORT COMBUSTION /EXCLUDES ALL OUTER COVERINGS/. SELECT REPLY CODE 10AA64 AARRD 09MATERIAL,JACKET JACKET MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE JACKET IS FABRICATED. SELECT REPLY CODE 10AD09 AARSD /D/ 19PROTECTION,ENVIRONMENTAL,OUTER COVERING OUTER COVERING ENVIRONMENTAL PROTECTION THE TYPE OF PROTECTION THE SURFACE TREATMENT OR JACKET PROVIDES. SELECT REPLY CODE 10AA65 AARTJ /D/ 10RATING IN DEG CELSIUS,TEMP TEMP RATING IN DEG CELSIUS THE MINIMUM AND/OR MAXIMUM TEMPERATURE FOR WHICH THE INSULATION IS DESIGNED TO INSULATE SATISFACTORILY, EXPRESSED IN DEGREES CELSIUS. 1D AND 1B MODE REPLY11AC20 AARUJ 04THICKNESS,INSULATION INSULATION THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION FROM THE INNER WALL TO THE OUTER WALL OF THE INSULATION,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AARVD 18TYPE,MEDIUM,ENVELOPE ENVELOPE MEDIUM TYPE INDICATES THE TYPE OF MEDIUM USED TO PRESSURIZE THE ENVELOPE. SELECT REPLY CODE 10AN91 AARWD 18TYPE ACCOMMODATED,FITTING FITTING TYPE ACCOMMODATED INDICATES THE TYPE OF FITTING THE ITEM WILL ACCOMMODATE. SELECT REPLY CODE 10AA66 AARXJ 04DIAMETER,INSIDE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AARYD 02DESIGN ACCOMMODATED,FITTING,END CONNECTION END CONNECTION FITTING DESIGN ACCOMMODATED THE TYPE OF END CONNECTION FOR WHICH THE FITTING TO BE INSULATED IS DESIGNED TO BE ACCOMMODATED. SELECT REPLY CODE 10AA67 AARZD /D/ 19FORM,DESIGN DESIGN FORM THE PHYSICAL CONFIGURATION OF THE ITEM. SELECT REPLY CODE 10AA68 AASAJ 04THREAD LENGTH THREAD LENGTH A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS. 2D AND 1B MODE REPLY21AA051AC20 AASBJ 04LENGTH,FASTENER FASTENER LENGTH THE DIMENSION,MEASURED ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS,FROM THE LARGEST BEARING SURFACE OF THE FASTENER HEAD TO THE EXTREME OPPOSITE END,OR AS SPECIFICALLY DESIGNATED FOR OTHER TYPE FASTENERS. 2D AND 1B MODE REPLY21AA051AC20 AASCD 19ITEMS,FURNISHED,INSTALLATION INSTALLATION FURNISHED ITEMS ITEMS FURNISHED TO AID IN THE INSTALLATION OF THERMAL INSULATION. SELECT REPLY CODE 10AA69 AASDD /D/ 08LOCATION,TREATMENT,SURFACE SURFACE TREATMENT LOCATION INDICATES THE LOCATION ON AN ITEM TO WHICH A SURFACE TREATMENT IS APPLIED. SELECT REPLY CODE 10AE46 AASEH /D/ 10HARDNESS RATING,METALLIC METALLIC HARDNESS RATING A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF A METALLIC ITEM WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE. 2D MODE REPLY 21AC204AC27 AASFJ 10HARDNESS RATING,NONMETALLIC NONMETALLIC HARDNESS RATING A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF A NONMETALLIC ITEM WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE. 2D AND 1B MODE REPLY21AC202AC26 AASGD 07INDICATOR,CASEHARDENING CASEHARDENING INDICATOR INDICATES WHETHER OR NOT A FERROUS ALLOY OBJECT HAS BEEN SUBJECTED TO A PROCESS WHEREBY THE OUTER PORTION IS MADE SUBSTANTIALLY HARDER THAN THE INNER PORTION OR CORE. SELECT REPLY CODE 10AA70 AASHJ A10STRENGTH,TENSILE,MINIMUM MINIMUM TENSILE STRENGTH THE MAXIMUM LOAD IN TENSION APPLIED IN A LONGITUDINAL DIRECTION,PER UNIT OF CROSS-SECTIONAL AREA,THAT THE MATERIAL CAN WITHSTAND WITHOUT RUPTURE. 1D AND 1A MODE REPLY11AB18 AASJJ /D/A10STRENGTH,YIELD,MINIMUM MINIMUM YIELD STRENGTH THE MAXIMUM LOAD IN TENSION THAT CAN BE APPLIED IN LONGITUDINAL DIRECTION PER CROSS-SECTIONAL UNIT WITHOUT PERMANENT DEFORMATION OF THE MATERIAL. 1D AND 1A MODE REPLY11AB18 AASKL 16STYLE,HEAD HEAD STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HEAD. 1L MODE REPLY 0 AASLJ 04DIAMETER,HEAD HEAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR HEAD,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AASMJ 04DIAMETER,COUNTERSINK,BOTTOM BOTTOM COUNTERSINK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AASNJ 04LENGTH,HANDLE HANDLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE HANDLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AASPJ 04WIDTH,HANDLE HANDLE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE HANDLE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AASQJ 04DIAMETER,HANDLE HANDLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR HANDLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AASRJ 04DIAMETER,INSIDE,HEAD HEAD INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AASSD 18TYPE,DESIGN,COLUMN,STEERING STEERING COLUMN DESIGN TYPE INDICATES THE DESIGN TYPE OF THE STEERING COLUMN. SELECT REPLY CODE 10AK54 AASTJ 04LENGTH,KEY KEY LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A KEY,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AASUJ 04HEIGHT,HEAD HEAD HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE HEAD,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AASVJ 04LENGTH,HEAD HEAD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A HEAD,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AASWJ 04LENGTH,PROJECTION,KEY KEY PROJECTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AASXJ 04DIAMETER,HEAD,CYLINDRICAL,TEE BOLT TEE BOLT CYLINDRICAL HEAD DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AASYJ 04DISTANCE FROM CENTERLINE TO FLAT DISTANCE FROM CENTERLINE TO FLAT NONE. 2D AND 1B MODE REPLY21AA051AC20 AASZJ 04THICKNESS,FLANGE,TEE HEAD TEE HEAD FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AATAB 04ANGLE IN DEG,COUNTERSINK COUNTERSINK ANGLE IN DEG THE INCLUDED ANGLE OF THE COUNTERSINK,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AATBJ 04WIDTH BETWEEN FLATS WIDTH BETWEEN FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 AATCJ 04DIAMETER,WASHER,EXTENDED EXTENDED WASHER DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AATDJ 04THICKNESS,WASHER,EXTENDED EXTENDED WASHER THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AATEB 04ANGLE IN DEG,CHAMFER CHAMFER ANGLE IN DEG THE MEASUREMENT OF THE CHAMFER ANGLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AATFJ 04DISTANCE FROM CENTER OF HEAD TO CENTER OF SHANK DISTANCE FROM CENTER OF HEAD TO CENTER OF SHANK THE DISTANCE,MEASURED ALONG A LINE PERPENDICULAR TO THE LONGITUDINAL AXIS,FROM THE CENTER OF THE HEAD TO THE CENTER OF THE SHANK. 2D AND 1B MODE REPLY21AA051AC20 AATGJ /D/A16STYLE DESIGNATOR,BOLT BOLT STYLE DESIGNATOR THE PARTICULAR PREFORMED SHAPE OF THE FASTENER. 1D AND 1B MODE REPLY11AA71 AATHJ /D/ 19BREADTH,EYE EYE BREADTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AATJJ /D/ 04LENGTH FROM THREAD END TO FURTHEST POINT INSIDE EYE LENGTH FROM THREAD END TO FURTHEST POINT INSIDE EYE NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 2D AND 1B MODE REPLY21AA051AC20 AATKJ 04DIAMETER,INSIDE,EYE EYE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE EYE AND TERMINATES AT THE INNER PERIPHERY. 2D AND 1B MODE REPLY21AA051AC20 AATLJ 04DISTANCE BETWEEN EYES DISTANCE BETWEEN EYES NONE. 2D AND 1B MODE REPLY21AA051AC20 AATMJ /D/ 04DISTANCE,OPENING,EYE EYE OPENING DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AATNJ 04DIAMETER,SHOULDER SHOULDER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SHOULDER AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AATPJ 04THICKNESS,SHOULDER SHOULDER THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AATQJ 04LENGTH,GRIP GRIP LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AATRJ 04LENGTH,SHANK SHANK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SHANK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AATSJ /D/ 04LENGTH,OVERALL OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AATTJ 10OFFSET,EYE EYE OFFSET NONE. 2D AND 1B MODE REPLY21AA051AC20 AATUJ 04LENGTH,EYE EYE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AATVJ 04WIDTH,EYE EYE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AATWJ 04DISTANCE FROM SHOULDER TO THREAD END DISTANCE FROM SHOULDER TO THREAD END NONE. 2D AND 1B MODE REPLY21AA051AC20 AATXJ 04LENGTH,SHOULDER SHOULDER LENGTH THE LENGTH OF THE ENLARGED PORTION OF THE SHANK ON THE ITEM,IN DISTINCTION FROM WIDTH OR DIAMETER. 2D AND 1B MODE REPLY21AA051AC20 AATYJ 04DISTANCE FROM SHOULDER TO EYE CENTER DISTANCE FROM SHOULDER TO EYE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AATZJ 04DIAMETER,STOCK,EYE EYE STOCK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAUAJ 04THICKNESS,STOCK,EYE EYE STOCK THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AAUBJ 04DIAMETER,HOLE HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AAUCJ /D/ 04LENGTH FROM INSIDE CENTER OF BEND TO THREAD END LENGTH FROM INSIDE CENTER OF BEND TO THREAD END NONE. 2D AND 1B MODE REPLY21AA051AC20 AAUDJ 04WIDTH,INSIDE,HOOK HOOK INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAUEJ 04DISTANCE FROM INSIDE CENTER OF BEND TO HOOK END DISTANCE FROM INSIDE CENTER OF BEND TO HOOK END NONE. 2D AND 1B MODE REPLY21AA051AC20 AAUFJ 04WIDTH,OPENING,HOOK HOOK OPENING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAUGJ 04LENGTH,SHANK SHANK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SHANK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AAUHJ 04DIAMETER,MINOR,SPLINE SPLINE MINOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST CROSS SECTION OF A SPLINE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AAUJJ 04DIAMETER,MAJOR,SPLINE SPLINE MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CROSS SECTION OF A SPLINE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AAUKJ 04WIDTH,SPLINE SPLINE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAULJ /D/ 04WIDTH BETWEEN FLATS WIDTH BETWEEN FLATS PLEASE USE MRC AATB IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 AAUMD 19FEATURE,LOCKING LOCKING FEATURE AN ELEMENT INSERTED INTO THE FASTENER,OR A DESIGN FEATURE,THAT ENABLES THE FASTENER TO EFFECTIVELY RESIST VIBRATION AND ROTATION. SELECT REPLY CODE 10AA72 AAUNB /D/ 04ANGLE IN DEG,HEAD,ASKEWED ASKEWED HEAD ANGLE IN DEG THE ANGLE OF THE HEAD BEARING SURFACE IN RELATION TO THE LONGITUDINAL AXIS OF THE FASTENER,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AAUPD /D/ 07INDICATOR,FINISH,HEAD HEAD FINISH INDICATOR AN INDICATION OF WHETHER OR NOT A FASTENING DEVICE IS FABRICATED TO PROVIDE MACHINED BEARING SURFACE IN TERMS OF A WASHER FACE OR CHAMFERED EDGE,OR OTHERWISE MACHINED TO FORM A BEARING SURFACE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. SELECT REPLY CODE 10AA73 AAUQJ /D/ 04LENGTH,GRIP GRIP LENGTH THE DISTANCE MEASURED ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS,WHICH DETERMINES THE MAXIMUM AND MINIMUM OF THE PLATES,STRUCTURES,PARTS,AND THE LIKE,TO BE JOINED. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 2D AND 1B MODE REPLY21AA051AC20 AAURJ 04DIAMETER,GRIP GRIP DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GRIP,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AAUSJ /D/A10MICROINCH FINISH AND LOCATION MICROINCH FINISH AND LOCATION DESIGNATES THE SPECIFIC MICROINCH FINISH AND ITS LOCATION ON AN ITEM. 1D AND 1A MODE REPLY12AE46 AAUTJ /D/A13THREAD SIZE,HOLE,CONCENTRIC CONCENTRIC HOLE THREAD SIZE THE THREAD SERIES, THREAD MAJOR/MAXIMUM DIAMETERS, AND THE NUMBER OF THREADS PER MEASUREMENT SCALE OF THE CONCENTRIC HOLE. 1D AND 1A MODE REPLY12AC21 AAUUA /D/ 13THREAD CLASS,HOLE,CONCENTRIC CONCENTRIC HOLE THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH-DIAMETER TOLERANCE OF A CONCENTRIC HOLE THREAD. 1A MODE REPLY 0 AAUVJ /D/T13THREAD PITCH DIAMETERS,HOLE,CONCENTRIC CONCENTRIC HOLE THREAD PITCH DIAMETERS A MEASUREMENT OF THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A CONCENTRIC HOLE THREAD. 1D AND 1F MODE REPLY11AA05 AAUWD /D/ 19CONFIGURATION,CONTROL,BRAKE BRAKE CONTROL CONFIGURATION THE ARRANGEMENT OF WHEELS AFFECTED BY CONTROL UNIT PRESSURE ADJUSTMENTS RESULTING FROM AN IMPENDING SKID CONDITION DETECTED AT A SINGLE WHEEL. SELECT REPLY CODE 10AB28 AAUXD 11METHOD,SIGNAL,APPLY,BRAKE BRAKE APPLY SIGNAL METHOD THE MEANS BY WHICH PILOT BRAKING COMMANDS ARE DIRECTED TO THE CONTROL UNIT. SELECT REPLY CODE 10AK88 AAUYJ 04LENGTH,POINT POINT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE POINT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AAUZB /D/ 04ANGLE IN DEG,CHAMFER,POINT POINT CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AAVAJ 04DIAMETER,POINT POINT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR POINT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AAVBB /D/ 04ANGLE IN DEG,INCLUDED,SWIVEL,POINT POINT SWIVEL INCLUDED ANGLE IN DEG NONE. 1B MODE REPLY 0 AAVCJ /D/ 04LENGTH,NECK,BOLT BOLT NECK LENGTH THE DISTANCE FROM THE LARGEST BEARING SURFACE OF THE HEAD TO THE BOTTOM OF THE OVAL OR SQUARE. 2D AND 1B MODE REPLY21AA051AC20 AAVDJ /D/ 04WIDTH,NECK,BOLT BOLT NECK WIDTH THE WIDTH OF THE SQUARE DIRECTLY BENEATH THE HEAD. 2D AND 1B MODE REPLY21AA051AC20 AAVEJ /D/ 04DIAMETER,LARGEST,NECK,BOLT BOLT NECK LARGEST DIAMETER THE LARGEST DIAMETER OF THE BOLT NECK DIRECTLY BENEATH THE HEAD. 2D AND 1B MODE REPLY21AA051AC20 AAVFJ /D/ 10SPEED,DEACTIVATION,ANTISKID ANTISKID DEACTIVATION SPEED THE APPROXIMATE AIRCRAFT SPEED AT WHICH ANTISKID FUNCTION IS RENDERED INACTIVE BY DESIGN. 2D AND 1B MODE REPLY21AA221AC20 AAVGD /D/ 14SHAPE,SHOULDER SHOULDER SHAPE THE PHYSICAL CONFIGURATION OF THE UNTHREADED PORTION OF A BODY ADJACENT TO THE HEAD WHICH IS LARGER THAN THE DIAMETER OF THE SHANK. SELECT REPLY CODE 10AD07 AAVHJ 04DIAMETER,SHOULDER SHOULDER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHOULDER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AAVJJ 04WIDTH ACROSS FLATS,SHOULDER SHOULDER WIDTH ACROSS FLATS THE SHORTEST DISTANCE FROM ONE FLATTED SURFACE OF THE SHOULDER TO THE OPPOSITE FLATTED SURFACE. 2D AND 1B MODE REPLY21AA051AC20 AAVKJ 04LENGTH,SHOULDER SHOULDER LENGTH THE LENGTH OF THE ENLARGED PORTION/S/ LOCATED ON THE SHANK OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 AAVLJ 04DIAMETER,PILOT PILOT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THAT PORTION USED TO GUIDE THE ITEM AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AAVMJ 04LENGTH,PILOT PILOT LENGTH THE LENGTH OF THE PILOT,WHICH IS THE UNTHREADED PORTION BEYOND THE THREAD USED TO GUIDE THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 AAVNA 12QUANTITY,FIN FIN QUANTITY THE NUMBER OF FINS INCLUDED ON THE ITEM. 1A MODE REPLY 0 AAVPJ 04DIAMETER,MAJOR,RIB RIB MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE RIB,AND TERMINATES AT THE OUTERMOST SURFACE OF THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AAVQJ 04LENGTH,RIB RIB LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A RIB ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS. 2D AND 1B MODE REPLY21AA051AC20 AAVRJ 04DISTANCE FROM LARGEST DIAMETER OF BEARING SURFACE OF HEAD TO RIBS DISTANCE FROM LARGEST DIAMETER OF BEARING SURFACE OF HEAD TO RIBS THE MEASUREMENT FROM THE LARGEST DIAMETER OF THE BEARING SURFACE OF THE HEAD TO THE RIBS. 2D AND 1B MODE REPLY21AA051AC20 AAVSB /D/ 04ANGLE IN DEG,INCLUDED,RIBS RIBS INCLUDED ANGLE IN DEG THE INCLUDED ANGLE BETWEEN THE RIBS, EXPRESSED IN DEGREES. 1B MODE REPLY 0 AAVTJ 04DIAMETER,MINOR,RIB RIB MINOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE RIB,AND TERMINATES AT THE INNERMOST SURFACE OF THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AAVUA 12QUANTITY,RIB RIB QUANTITY THE NUMBER OF RIBS INCLUDED ON THE ITEM. 1A MODE REPLY 0 AAVVL 16STYLE,WASHER WASHER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE WASHER. 1L MODE REPLY 0 AAVWA 12QUANTITY,WASHER WASHER QUANTITY THE NUMBER OF WASHERS INCLUDED ON THE ITEM. 1A MODE REPLY 0 AAVXJ 04DIAMETER,OUTSIDE,WASHER WASHER OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAVYJ 04THICKNESS,MATERIAL MATERIAL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AAVZJ 04DIAMETER,GROOVE GROOVE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GROOVE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AAWAJ /D/ 04DISTANCE FROM LARGEST BEARING SURFACE OF HEAD OR MACHINE SCREW END TO THE CENTER OF HOLE IN SHANK DISTANCE FROM LARGEST BEARING SURFACE OF HEAD OR MACHINE SCREW END TO THE CENTER OF HOLE IN SHANK THE DISTANCE FROM THE CENTER OF THE HOLE IN THE SHANK TO THE LARGEST BEARING SURFACE OF THE HEAD OR THE NEAREST MACHINE SCREW END. 2D AND 1B MODE REPLY21AA051AC20 AAWBJ 04DIAMETER,HOLE,UNTHREADED,SHANK SHANK UNTHREADED HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SHANK UNTHREADED HOLE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AAWCJ 04DIAMETER FROM HEAD,FIRST FIRST DIAMETER FROM HEAD NONE. 2D AND 1B MODE REPLY21AA051AC20 AAWDJ 04DIAMETER FROM HEAD,SECOND SECOND DIAMETER FROM HEAD NONE. 2D AND 1B MODE REPLY21AA051AC20 AAWEJ 04DIAMETER FROM HEAD,THIRD THIRD DIAMETER FROM HEAD NONE. 2D AND 1B MODE REPLY21AA051AC20 AAWFJ 04DIAMETER FROM HEAD,FOURTH FOURTH DIAMETER FROM HEAD NONE. 2D AND 1B MODE REPLY21AA051AC20 AAWGJ 04DIAMETER FROM HEAD,FIFTH FIFTH DIAMETER FROM HEAD NONE. 2D AND 1B MODE REPLY21AA051AC20 AAWHJ 04DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF THE FIRST DIAMETER DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF FIRST DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAWJJ 04DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF SECOND DIAMETER DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF SECOND DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAWKJ 04DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF THIRD DIAMETER DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF THIRD DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAWLJ 04DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF FOURTH DIAMETER DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF FOURTH DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAWMJ 04DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF FIFTH DIAMETER DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF FIFTH DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAWND 14SHAPE,CROSS-SECTIONAL,BODY BODY CROSS-SECTIONAL SHAPE THE PHYSICAL CONFIGURATION OF THE BODY WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 AAWPJ /D/ 04DISTANCE FROM UNDERSIDE OF HEAD TO BEGINNING OF UNDERCUT DISTANCE FROM UNDERSIDE OF HEAD TO BEGINNING OF UNDERCUT THE DISTANCE BETWEEN TWO THREADED PORTIONS OF THE FASTENER WHOSE OUTSIDE DIAMETER IS LESS THAN THE NOMINAL SIZE OF THE THREADED PORTION. 2D AND 1B MODE REPLY21AA051AC20 AAWQJ 04DIAMETER,STOCK,RING RING STOCK DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE RING STOCK,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AAWRJ 04DIAMETER,INSIDE,RING RING INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE RING,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AAWSA 12QUANTITY,PROJECTION,WELDING WELDING PROJECTION QUANTITY THE NUMBER OF WELDING PROJECTIONS INCLUDED ON THE ITEM. 1A MODE REPLY 0 AAWTD /D/ 08LOCATION,PROJECTION,WELDING WELDING PROJECTION LOCATION INDICATES THE LOCATION OF WELDING PROJECTIONS ON THE ITEM. SELECT REPLY CODE 10AE46 AAWUJ A10STRENGTH,SHEAR,SINGLE SINGLE SHEAR STRENGTH THE MINIMUM LOAD,APPLIED PERPENDICULARLY TO THE LONGITUDINAL AXIS OF AN ITEM,AT WHICH POINT THE ITEM WILL FRACTURE WHEN SUBJECTED TO THE STANDARD SINGLE SHEAR TEST METHOD. 1D AND 1A MODE REPLY11AB18 AAWVJ 04DISTANCE FROM INSIDE CENTER OF BEND TO BOLT END DISTANCE FROM INSIDE CENTER OF BEND TO BOLT END NONE. 2D AND 1B MODE REPLY21AA051AC20 AAWWJ 04DISTANCE BETWEEN SHANKS,INSIDE INSIDE DISTANCE BETWEEN SHANKS NONE. 2D AND 1B MODE REPLY21AA051AC20 AAWXJ 04DEPTH,HOLE,CONCENTRIC CONCENTRIC HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAWYJ 04DIAMETER,COUNTERBORE COUNTERBORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COUNTERBORED PORTION OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AAWZJ 04DEPTH,COUNTERBORE COUNTERBORE DEPTH THE DEPTH OF THE PROCESS USED TO ENLARGE PART OF A HOLE. 2D AND 1B MODE REPLY21AA051AC20 AAXAJ /D/ 13THREAD DEPTH,INTERNAL INTERNAL THREAD DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAXBJ 04DIAMETER,SHOULDER SHOULDER DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAXCJ 04DIAMETER,HOLE,CONCENTRIC CONCENTRIC HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAXDJ /D/ 04LENGTH,SHOULDER SHOULDER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAXEJ 04LENGTH LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AAXFJ 04WIDTH,SPREAD,WING WING SPREAD WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAXGA /D/ 12QUANTITY,COMPRESSOR COMPRESSOR QUANTITY THE NUMBER OF COMPRESSORS INCORPORATED IN THE UNIT. 1A MODE REPLY 0 AAXHA 12QUANTITY,PRIME MOVER PRIME MOVER QUANTITY THE NUMBER OF PRIME MOVERS INCORPORATED IN THE UNIT. 1A MODE REPLY 0 AAXJA 10CYCLE IN PERCENT,DUTY DUTY CYCLE IN PERCENT THE PERCENTAGE OF TIME FOR WHICH THE ITEM IS DESIGNED TO GENERATE WITHOUT DEGRADATION OF RATED CAPACITY AND DISCHARGE PRESSURE. 1A MODE REPLY 0 AAXKD 19GAS FOR WHICH DESIGNED GAS FOR WHICH DESIGNED THE MEDIA THE MACHINE IS DESIGNED TO COMPRESS. SELECT REPLY CODE 10AB75 AAXLJ 10FLOW RATE,DISCHARGE DISCHARGE FLOW RATE THE RATED CAPACITY OF GAS DELIVERED BY THE LAST STAGE OF COMPRESSION. 1D AND 1B MODE REPLY11AC64 AAXMJ 10PRESSURE,DISCHARGE DISCHARGE PRESSURE THE GAGE PRESSURE OF GAS DELIVERED BY THE LAST STAGE OF COMPRESSION. REFERRED TO AS CONDENSING PRESSURE FOR REFRIGERATION COMPRESSORS. 1D AND 1B MODE REPLY11AA95 AAXNB /D/ 10TEMP IN DEG CELSIUS,DISCHARGE DISCHARGE TEMP IN DEG CELSIUS THE DISCHARGE TEMPERATURE OF THE REFRIGERANT GAS MEASURED JUST UPSTREAM OF THE COMPRESSOR DISCHARGE CONNECTION ON THE HIGH SIDE OF THE SYSTEM, EXPRESSED IN DEGREES CELSIUS. 1B MODE REPLY 0 AAXPD 02DESIGN,SYSTEM,COOLING COOLING SYSTEM DESIGN THE DESIGN OF THE SYSTEM NECESSARY TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF AN ITEM AND DISCHARGE TEMPERATURE OF THE COMPRESSED GASES. SELECT REPLY CODE 10AA74 AAXQD /D/ 19MEDIUM,COOLING,COMPRESSED GAS COMPRESSED GAS COOLING MEDIUM THE COOLING MEDIUM USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE COMPRESSED GASES. USE MRC ACZV AND ISAC TO TABLE 0094 SELECT REPLY CODE 10AB75 AAXRD /D/ 19MEDIUM,COOLING,COMPRESSOR COMPRESSOR COOLING MEDIUM THE COOLING MEDIUM USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE COMPRESSOR. USE MRC ACZV AND ISAC TO TABLE 0094 SELECT REPLY CODE 10AB75 AAXSD /D/ 19MEDIUM,COOLING,PRIME MOVER PRIME MOVER COOLING MEDIUM THE COOLING MEDIUM USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE PRIME MOVER. USE MRC ACZV AND ISAC TO TABLE 0094 SELECT REPLY CODE 10AB75 AAXTJ 10FLOW RATE,COOLANT,COOLING SYSTEM COOLING SYSTEM COOLANT FLOW RATE THE AMOUNT OF COOLANT NECESSARY TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE ITEM. 1D AND 1B MODE REPLY11AC64 AAXUD 18TYPE,EQUIPMENT,GAS COOLING GAS COOLING EQUIPMENT TYPE THE POSITION OF THE GAS COOLING EQUIPMENT WHETHER BETWEEN STAGES /INTERCOOLER/,AFTER THE LAST STAGE /AFTERCOOLER/,OR BOTH. SELECT REPLY CODE 10AA76 AAXVD /D/ 18TYPE,UNLOADER UNLOADER TYPE THE METHOD BY WHICH A NO LOAD CONDITION IS OBTAINED FOR STARTING THE ITEM. SELECT REPLY CODE 10AA77 AAXWB /D/ 10HORSEPOWER REQUIRED,BRAKE BRAKE HORSEPOWER REQUIRED THE POWER REQUIRED TO START AND OPERATE THE ITEM AT THE ACTUAL RATED CAPACITY,INCLUDING ALL ACCESSORIES. 1B MODE REPLY 0 AAXXD 18TYPE,MOUNTING MOUNTING TYPE INDICATES THE TYPE OF MOUNT UTILIZED TO SUPPORT THE ITEM. SELECT REPLY CODE 10AA78 AAXYD 02DESIGN,COMPRESSOR,RECIPROCATING RECIPROCATING COMPRESSOR DESIGN THE RECIPROCATING COMPRESSOR DESIGN AS DETERMINED BY THE MECHANICAL ACTION BY WHICH COMPRESSION TAKES PLACE IN THE CYLINDER/S/ OF THE COMPRESSOR. SELECT REPLY CODE 10AA79 AAXZA 12QUANTITY,CYLINDER CYLINDER QUANTITY THE NUMBER OF CYLINDERS INCORPORATED IN THE ITEM. 1A MODE REPLY 0 AAYAL 16STYLE,ARRANGEMENT,CYLINDER CYLINDER ARRANGEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ANGULAR ARRANGEMENT OF THE CYLINDERS. 1L MODE REPLY 0 AAYBD 02DESIGN,COMPRESSOR,ROTARY ROTARY COMPRESSOR DESIGN THE MECHANICAL ACTION BY WHICH COMPRESSION TAKES PLACE. SELECT REPLY CODE 10AA81 AAYCD 02DESIGN,COMPRESSOR,CENTRIFUGAL CENTRIFUGAL COMPRESSOR DESIGN THE DESIGN OF A NONPOSITIVE DISPLACEMENT CENTRIFUGAL COMPRESSOR AS DETERMINED BY THE DIRECTION OF FLOW,WITH RESPECT TO THE AXIS,OF THE COMPRESSED GAS. SELECT REPLY CODE 10AA80 AAYDA 12QUANTITY,STAGE STAGE QUANTITY THE NUMBER OF STAGES INCORPORATED IN THE ITEM. 1A MODE REPLY 0 AAYEB 10FLOW RATE IN TONS PER HOUR,REFRIGERATION REFRIGERATION FLOW RATE IN TONS PER HOUR THE REFRIGERATION CAPACITY OF THE ITEM AS RATED BY INDUSTRY,EXPRESSED IN TONS PER HOUR. 1B MODE REPLY 0 AAYFJ 10PRESSURE,SUCTION SUCTION PRESSURE THE PRESSURE OF THE GAS AFTER IT HAS PASSED THROUGH THE EVAPORATOR AND PRIOR TO ITS COMPRESSION WITHIN THE ITEM. 1D AND 1B MODE REPLY11AB18 AAYGB /D/ 10TEMP IN DEG CELSIUS,SUCTION SUCTION TEMP IN DEG CELSIUS THE TEMPERATURE OF THE GAS MEASURED JUST DOWNSTREAM OF THE COMPRESSOR SUCTION CONNECTION IN THE LOW SIDE OF THE SYSTEM, EXPRESSED IN DEGREES CELSIUS. 1B MODE REPLY 0 AAYHD /D/ 18TYPE,MOVER,PRIME PRIME MOVER TYPE INDICATES THE TYPE OF PRIME MOVER INCLUDED WITH THE UNIT. SELECT REPLY CODE 10AA82 AAYJJ 10FLOW RATE,FLUID,HYDRAULIC HYDRAULIC FLUID FLOW RATE THE AMOUNT OF HYDRAULIC FLUID REQUIRED TO OPERATE THE ITEM. 1D AND 1B MODE REPLY11AC64 AAYKJ 10PRESSURE,HYDRAULIC HYDRAULIC PRESSURE THE GAGE PRESSURE REQUIRED TO OPERATE THE ITEM. 1D AND 1B MODE REPLY11AA95 AAYLJ 10PRESSURE,OPERATING,STEAM STEAM OPERATING PRESSURE THE STEAM PRESSURE REQUIRED TO MOTIVATE THE STEAM ENGINE OR TURBINE USED AS THE PRIME MOVER. 1D AND 1B MODE REPLY11AA95 AAYMJ /D/A16STYLE AND LOCATION,DRIVE,INTERNAL INTERNAL DRIVE STYLE AND LOCATION DESIGNATES THE STYLE OF INTERNAL DRIVE AND ITS LOCATION ON THE FASTENING DEVICE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 1D AND 1A MODE REPLY13AE46 AAYNB /D/ 10TEMP IN DEG CELSIUS,STEAM STEAM TEMP IN DEG CELSIUS THE TEMPERATURE OF THE STEAM REQUIRED TO OPERATE A COMPRESSOR AT FULL CAPACITY, EXPRESSED IN DEGREES CELSIUS. 1B MODE REPLY 0 AAYPJ 10PRESSURE,EXHAUST EXHAUST PRESSURE THE GAGE PRESSURE OF THE EXPANDED STEAM AFTER DRIVING THE PRIME MOVER. 1D AND 1B MODE REPLY11AA95 AAYQB /D/ 10RATE IN POUNDS PER HORSEPOWER HOUR,CONSUMPTION,STEAM STEAM CONSUMPTION RATE IN POUNDS PER HORSEPOWER HOUR THE RATE AT WHICH STEAM IS CONSUMED BY THE PRIME MOVER WHEN OPERATING AT FULL CAPACITY. 1B MODE REPLY 0 AAYRJ /D/ 10CAPACITY,TANK,RECEIVER RECEIVER TANK CAPACITY THE VOLUME OF THE AIR STORAGE CONTAINER/S/,INCLUDING OIL STORAGE FOR ROTARY DESIGNS WHEN APPLICABLE. 1D AND 1B MODE REPLY11AB10 AAYSB 10SPEED AT RATED CAPACITY IN RPM,COMPRESSOR COMPRESSOR SPEED AT RATED CAPACITY IN RPM THE SPEED OF THE COMPRESSOR REQUIRED TO PRODUCE ITS RATED CAPACITY,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 AAYTA 12QUANTITY,CONNECTION,INTAKE INTAKE CONNECTION QUANTITY THE NUMBER OF INTAKE CONNECTIONS INCLUDED ON THE ITEM. 1A MODE REPLY 0 AAYUD 18TYPE,CONNECTION,INTAKE INTAKE CONNECTION TYPE INDICATES THE TYPE OF INTAKE CONNECTION INCLUDED ON THE ITEM. SELECT REPLY CODE 10AA84 AAYVA 12QUANTITY,CONNECTION,DISCHARGE DISCHARGE CONNECTION QUANTITY THE NUMBER OF DISCHARGE CONNECTIONS INCLUDED ON THE ITEM. 1A MODE REPLY 0 AAYWD 18TYPE,CONNECTION,DISCHARGE DISCHARGE CONNECTION TYPE INDICATES THE TYPE OF DISCHARGE CONNECTION INCLUDED ON THE ITEM. SELECT REPLY CODE 10AA84 AAYXD 18TYPE,CONNECTION,DRIVE DRIVE CONNECTION TYPE INDICATES THE TYPE OF CONNECTION BETWEEN THE PRIME MOVER AND THE SHAFT. SELECT REPLY CODE 10AA85 AAYYD /D/ 18TYPE,DEVICE,SAFETY SAFETY DEVICE TYPE INDICATES THE TYPE OF SAFETY DEVICE(S) PROVIDED. SELECT REPLY CODE 10AA86 AAYZD 18TYPE,DEVICE,CONTROL CONTROL DEVICE TYPE INDICATES THE TYPE OF CONTROL DEVICE PROVIDED. SELECT REPLY CODE 10AA87 AAZAD 18TYPE,SILENCER SILENCER TYPE INDICATES A DEVICE USED TO ELIMINATE THE NOISE OF THE INTAKE OR DISCHARGE OF THE ITEM. SELECT REPLY CODE 10AA88 AAZBD /D/ 07EQUIPMENT,HEATING HEATING EQUIPMENT HEATING EQUIPMENT WHICH MAY BE INSTALLED ON THE ITEM TO FACILITATE EXTREME COLD WEATHER OPERATION. SELECT REPLY CODE 10AN33 AAZCB /D/ 10TEMP IN DEG CELSIUS,OPERATING,MINIMUM MINIMUM OPERATING TEMP IN DEG CELSIUS THE MINIMUM OPERATING TEMPERATURE AT WHICH THE ITEM IS RATED,EXPRESSED IN DEGREES CELSIUS. 1B MODE REPLY 0 AAZDD /D/ 07TREATMENT,RESISTANT,FUNGUS FUNGUS RESISTANT TREATMENT A TREATMENT WHICH MAY BE APPLIED TO PRODUCE A FUNGUS RESISTANT CONDITION. SELECT REPLY CODE 10AA89 AAZEJ 04DIAMETER,SHANK SHANK DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY OF THE SHANK AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AAZFL 16STYLE,SHANK SHANK STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SHANK. 1L MODE REPLY 0 AAZGJ 04DIAMETER,MAJOR,HEAD HEAD MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAZHJ 04DIAMETER,MINOR,HEAD HEAD MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAZJJ 04HEIGHT,COUNTERSINK COUNTERSINK HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AAZKJ 04WIDTH ACROSS FLATS WIDTH ACROSS FLATS THE SHORTEST STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT OF THE WRENCHING SURFACE. 2D AND 1B MODE REPLY21AA051AC20 AAZLJ 04DIAMETER,MINOR,TAPERED HOLE TAPERED HOLE MINOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST END OF A TAPERED HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AAZMJ /D/ 04DIAMETER,HOLE,SHANK END SHANK END HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAZNJ /D/ 04WIDTH,SLOT,MINOR MINOR SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAZPJ 04LENGTH,CHAMFER CHAMFER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CHAMFER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AAZQJ 04DEPTH,HOLE HOLE DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE HOLE,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AAZRJ 04DIAMETER,MAJOR MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST DIAMETER OF THE ITEM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AAZSJ /D/ 04WIDTH,SLOT,MAJOR MAJOR SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAZTJ 04DEPTH,SLOT SLOT DEPTH THE MEASUREMENT BETWEEN SPECIFIED POINTS OF THE SLOT,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AAZUJ 04DIAMETER,TIP TIP DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR TIP,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AAZVJ /D/ 04RADIUS,TIP TIP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AAZWJ 04DIAMETER,SHOULDER,SECOND SECOND SHOULDER DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AAZXJ 04LENGTH,SHOULDER,SECOND SECOND SHOULDER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AAZYA /D/ 16STYLE,COLLAR COLLAR STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE COLLAR. 1A MODE REPLY 0 AAZZA /D/ 16STYLE,CAP CAP STYLE THE PHYSICAL CONFIGURATION OF THE CAP. 1A MODE REPLY 0 ABAAJ 04DIAMETER,OUTSIDE,COLLAR COLLAR OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABABJ 04HEIGHT,OVERALL,COLLAR COLLAR OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ABACJ 04DIAMETER,INSIDE,CAP CAP INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABADJ 04DIAMETER,OUTSIDE,CAP CAP OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABAEJ 04HEIGHT,OVERALL,CAP CAP OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ABAFD 19DEVICE,EXPANSION EXPANSION DEVICE THE DEVICE BY WHICH THE ITEM IS EXPANDED AND SET. SELECT REPLY CODE 10AA90 ABAGD /D/ 18TYPE,SEAL,FLUID TIGHT FLUID TIGHT SEAL TYPE INDICATES THE TYPE OF SEALING ELEMENT DESIGNED TO PREVENT FLUID PASSAGE. SELECT REPLY CODE 10AA91 ABAHD /D/ 09MATERIAL,SEAL SEAL MATERIAL THE ELEMENT, COMPOUND,OR MIXTURE FROM WHICH THE SEAL IS FABRICATED. SELECT REPLY CODE 10AD09 ABAJD 19LUBRICATION LUBRICATION A SUBSTANCE DESIGNED TO PROVIDE A REDUCTION OF FRICTION BETWEEN THE TWO SURFACES IN CONTACT. SELECT REPLY CODE 10AA92 ABAKB 10DELIVERY RATE IN BTU PER HOUR,HEAT HEAT DELIVERY RATE IN BTU PER HOUR THE MAXIMUM OUTPUT OF THE UNIT,EXPRESSED IN BRITISH THERMAL UNITS PER HOUR. 1B MODE REPLY 0 ABALD /D/ 18TYPE,ELEMENT,HEATING HEATING ELEMENT TYPE INDICATES THE TYPE OF HEATING UNIT WHICH IMPARTS HEAT. SELECT REPLY CODE 10AA93 ABAMD /D/ 18TYPE,MEDIUM,HEAT HEAT MEDIUM TYPE INDICATES THE HEAT MEDIUM TYPE FOR WHICH THE UNIT IS DESIGNED. SELECT REPLY CODE 10AA94 ABANJ 10LIMIT,PRESSURE,MAXIMUM MAXIMUM PRESSURE LIMIT INDICATES THE LIMIT OF THE MAXIMUM PRESSURE FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AA95 ABAPD /D/ 18TYPE,FEED,FUEL FUEL FEED TYPE THE METHOD BY WHICH THE FUEL IS SUPPLIED FROM THE TANK OR OTHER CONTAINER TO THE BURNER. SELECT REPLY CODE 10AA96 ABAQD 19POSITION,OUTLET OUTLET POSITION THE POSITION OF THE OUTLET(S) ON THE ITEM. SELECT REPLY CODE 10AA97 ABARJ /D/ 10CAPACITY,TANK,FUEL,INTEGRAL INTEGRAL FUEL TANK CAPACITY THE QUANTITY OF LIQUID FUEL THAT THE TANK WILL HOLD. PLEASE USE MRC CRJT IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1B MODE REPLY11AB10 ABASD /D/ 11METHOD,IGNITION IGNITION METHOD THE MEANS BY WHICH THE FUEL IS IGNITED. SELECT REPLY CODE 10AA98 ABATJ 04HEIGHT,DUCT DUCT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE DUCT,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 ABAUJ 04WIDTH,DUCT DUCT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE DUCT,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 ABAVJ /D/ 04DIAMETER,DUCT DUCT DIAMETER THE DIAMETER OF A CYLINDRICAL SHAPED DUCT FOR WHICH A DUCT TYPE HEATER IS DESIGNED TO FIT. 1D AND 1B MODE REPLY11AA05 ABAWA 12QUANTITY,OUTLET,HEAT HEAT OUTLET QUANTITY THE NUMBER OF HEAT OUTLETS INCLUDED ON THE ITEM. 1A MODE REPLY 0 ABAXD 05DIRECTION,DELIVERY,HEAT HEAT DELIVERY DIRECTION THE DIRECTION IN WHICH THE HEAT IS DISCHARGED FROM THE ITEM. SELECT REPLY CODE 10AA99 ABAYD 18TYPE,OUTLET,HEAT DISCHARGE HEAT DISCHARGE OUTLET TYPE INDICATES THE TYPE OF OUTLET(S) PROVIDED FOR THE DISCHARGE OF HEAT. SELECT REPLY CODE 10AB00 ABAZD 19DEVICE,DIRECTING,HEAT HEAT DIRECTING DEVICE INDICATES THE DEVICE/S/ PROVIDED FOR THE PURPOSE OF DIRECTING THE FLOW OF HEAT. SELECT REPLY CODE 10AB01 ABBAD 19DEVICE,CIRCULATION,AIR AIR CIRCULATION DEVICE THE MECHANISM USED FOR AIR CIRCULATION. SELECT REPLY CODE 10AB02 ABBBD 10ADJUSTMENTS,SPEED SPEED ADJUSTMENTS THE DIFFERENT SPEEDS AT WHICH THE ITEM MAY BE OPERATED. SELECT REPLY CODE 10AB03 ABBCJ /D/A19CONFIGURATION,HOLE,HEAD HEAD HOLE CONFIGURATION CONSISTS OF THE CONFIGURATION,NUMBER OF HOLES,AND EITHER THE DIAMETER OF DRILLED HOLES OR THE SIZE DESIGNATION OF TAPPED HOLES /SCREW SIZE NUMBER AND NUMBER OF THREADS PER INCH/. 1D AND 1A MODE REPLY12AC34 ABBDJ 10FLOW RATE,AIR,MAXIMUM MAXIMUM AIR FLOW RATE THE MAXIMUM RATED CAPACITY OF AIR FLOW MOVED THROUGH THE ITEM. 1D AND 1B MODE REPLY11AC64 ABBED 18TYPE,AIR,CIRCULATED CIRCULATED AIR TYPE INDICATES THE TYPE OF AIR THE ITEM IS DESIGNED TO CIRCULATE. SELECT REPLY CODE 10AB05 ABBFD 18TYPE,FILTER,AIR AIR FILTER TYPE INDICATES THE TYPE OF AIR FILTER INCLUDED ON THE ITEM. SELECT REPLY CODE 10AB06 ABBGD /D/ 18TYPE,DAMPER,VENTILATION VENTILATION DAMPER TYPE INDICATES THE TYPE OF DAMPER PROVIDED TO CONTROL VENTILATION. SELECT REPLY CODE 10AA77 ABBHD /D/ 09MATERIAL,INCLOSURE INCLOSURE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INCLOSURE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC CQSJ IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 ABBJD /D/ 18TYPE,CONTROL,OPERATING OPERATING CONTROL TYPE INDICATES THE TYPE OF DEVICE WHICH CONTROLS THE OPERATION OF THE ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. SELECT REPLY CODE 10AB09 ABBKD /D/ 18TYPE,CONTROL,HUMIDITY HUMIDITY CONTROL TYPE INDICATES THE TYPE OF CONTROL DESIGNED TO REGULATE THE MOISTURE IN THE AIR. SELECT REPLY CODE 10AA77 ABBLJ 04LENGTH,HANDLE HANDLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE HANDLE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 ABBMJ /D/ 10RATE PER HOUR,CONSUMPTION,FUEL FUEL CONSUMPTION RATE PER HOUR FUEL REQUIRED PER HOUR TO OPERATE THE UNIT AT RATED CAPACITY. 1D AND 1B MODE REPLY11AB10 ABBNJ 04LENGTH,OVERALL,SECTION SECTION OVERALL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ABBPJ 04DIAMETER,SECTION SECTION DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ABBQD /D/ 11METHOD,COUPLING,END END COUPLING METHOD THE FACILITY PROVIDED ON THE END/S/ FOR ATTACHING ADDITIONAL SECTIONS. SELECT REPLY CODE 10AB11 ABBRD 19ACCOMMODATION,WIRE,GROUND GROUND WIRE ACCOMMODATION THE FACILITY PROVIDED FOR ATTACHING A GROUND WIRE TO THE ITEM. SELECT REPLY CODE 10AB12 ABBSA 18TYPE,DEVICE,INFLATION INFLATION DEVICE TYPE INDICATES THE TYPE OF VALVE OR SPUD PROVIDED TO FACILITATE INFLATION OF THE ITEM. 1A MODE REPLY 0 ABBTD 19POSITION,DEVICE,INFLATION INFLATION DEVICE POSITION AN INDICATION OF THE RELATIVE POSITION OF AN INFLATION VALVE OR SPUD IN RELATION TO THE INNER TUBE CENTERLINE. SELECT REPLY CODE 10AB13 ABBUD /D/ 11METHOD,REGULATION,PRESSURE,BRAKE,ANTISKID ANTISKID BRAKE PRESSURE REGULATION METHOD THE MEANS OF HYDRAULIC BRAKING PRESSURE CONTROL APPLIED TO PREVENT A LOCKED WHEEL CONDITION. SELECT REPLY CODE 10AD63 ABBVD /D/ 07FEATURE,SEALING,PUNCTURE PUNCTURE SEALING FEATURE AN INDICATION OF WHETHER OR NOT A PUNCTURE SEALING FEATURE IS INCLUDED. SELECT REPLY CODE 10AN33 ABBWD 19CONSTRUCTION CONSTRUCTION A FEATURE BUILT INTO THE ITEM WHICH APPLIES TO ITS ABILITY TO RETAIN AIR IF PUNCTURED. SELECT REPLY CODE 10AB14 ABBXD 19CONSTRUCTION,BASE BASE CONSTRUCTION THE CONSTRUCTION OF THAT PORTION OF THE ITEM WHICH IS IN CONTACT WITH THE TIRE FLAP OR RIM WHEN INSTALLED IN A PNEUMATIC TIRE. SELECT REPLY CODE 10AB15 ABBYJ A10STRENGTH,TENSILE,MINIMUM RATED,SPLICE SPLICE MINIMUM RATED TENSILE STRENGTH THE MAXIMUM LOAD IN TENSION APPLIED,TO A SPLICE,IN A LONGITUDINAL DIRECTION PER UNIT OF CROSS-SECTIONAL AREA THAT THE MATERIAL CAN WITHSTAND WITHOUT RUPTURE. 1D AND 1A MODE REPLY11AB18 ABBZA 03DESIGNATION,SIZE,AWG CONDUCTOR WIRE,MAXIMUM MAXIMUM AWG CONDUCTOR WIRE SIZE DESIGNATION THE LARGEST AMERICAN WIRE GAGE SIZE DESIGNATION OF WIRE THE FACILITY FOR ATTACHING A CONDUCTOR WIRE WILL ACCOMMODATE. 1A MODE REPLY 0 ABCAA 03DESIGNATION,SIZE,AWG CONDUCTOR WIRE,MINIMUM MINIMUM AWG CONDUCTOR WIRE SIZE DESIGNATION THE SMALLEST AMERICAN WIRE GAGE SIZE DESIGNATION OF WIRE THE FACILITY FOR ATTACHING A CONDUCTOR WIRE WILL ACCOMMODATE. 1A MODE REPLY 0 ABCBJ 04LENGTH,WIRE,GROUND GROUND WIRE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE GROUND WIRE PROVIDED WITH OR AS A PART OF THE ITEM. 1D AND 1B MODE REPLY11AA05 ABCCD 18TYPE,TERMINATION,WIRE WIRE TERMINATION TYPE INDICATES THE TYPE OF TERMINATION PROVIDED ON THE WIRE. SELECT REPLY CODE 10AB17 ABCDJ 04DISTANCE,MINIMUM,JAW OPENING,ELECTRICAL CLIP ELECTRICAL CLIP JAW OPENING MINIMUM DISTANCE THE MINIMUM ACCEPTABLE JAW OPENING WITH THE JAW FULLY OPENED. 1D AND 1B MODE REPLY11AA05 ABCEJ 04WIDTH,MINIMUM,TERMINAL LUG SLOT TERMINAL LUG SLOT MINIMUM WIDTH THE SMALLEST ACCEPTABLE WIDTH OF THE TERMINAL LUG SLOT PROVIDED. 1D AND 1B MODE REPLY11AA05 ABCFJ /D/A10STRENGTH,SHEAR,DOUBLE DOUBLE SHEAR STRENGTH THE MINIMUM LOAD,APPLIED PERPENDICULARLY TO THE LONGITUDINAL AXIS OF AN ITEM,AT WHICH POINT THE ITEM WILL FRACTURE WHEN SUBJECTED TO THE STANDARD DOUBLE SHEAR TEST METHOD. 1D AND 1A MODE REPLY11AB18 ABCGJ 04DIAMETER,MINIMUM,TERMINAL LUG HOLE TERMINAL LUG HOLE MINIMUM DIAMETER THE MINIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A TERMINAL LUG HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ABCHD 14SHAPE,POINT POINT SHAPE THE PHYSICAL CONFIGURATION OF THE POINT. SELECT REPLY CODE 10AD07 ABCJJ 04DIAMETER,INSIDE,COLLAR COLLAR INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABCKD /D/ 18TYPE,ASSEMBLY ASSEMBLY TYPE INDICATES THE TYPE OR KIND OF ASSEMBLY WHICH THE ASSEMBLED BOARDS MAKE INTO ONE COMPOSITE. SELECT REPLY CODE 10AB19 ABCLA 12QUANTITY PER ASSEMBLY,BOARD,TERMINAL TERMINAL BOARD QUANTITY PER ASSEMBLY THE NUMBER OF TERMINAL BOARDS COMPRISING A TERMINAL BOARD ASSEMBLY. 1A MODE REPLY 0 ABCMJ X19CODE AND PART NUMBER,MANUFACTURER,TERMINAL BOARD TERMINAL BOARD MANUFACTURER CODE AND PART NUMBER THE MANUFACTURER'S CODE AND PART NUMBER FOR EACH DIFFERENT TYPE OF TERMINAL BOARD COMPRISING A TERMINAL BOARD ASSEMBLY. 1D AND 1A MODE REPLY15AA10 ABCNJ 04LENGTH,OVERALL,ASSEMBLY ASSEMBLY OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT EXTREME ENDS OF AN ASSEMBLY. 1D AND 1B MODE REPLY11AA05 ABCPJ 04WIDTH,OVERALL,ASSEMBLY ASSEMBLY OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ASSEMBLY,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 ABCQJ 04HEIGHT,OVERALL,ASSEMBLY ASSEMBLY OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ASSEMBLY. 1D AND 1B MODE REPLY11AA05 ABCRL /D/ 16STYLE,PATTERN,TERMINAL TERMINAL PATTERN STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OR POSITION OF THE TERMINALS. 1L MODE REPLY 0 ABCSA 12QUANTITY,ROW,TERMINAL TERMINAL ROW QUANTITY THE NUMBER OF TERMINAL ROWS OR TERMINAL PROVISIONS INCLUDED ON THE ITEM. 1A MODE REPLY 0 ABCTJ 04DISTANCE BETWEEN TERMINALS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN TERMINALS THE CENTER TO CENTER DISTANCE BETWEEN TERMINALS. 1D AND 1B MODE REPLY11AA05 ABCUJ 04DISTANCE BETWEEN TERMINAL ROW CENTERS DISTANCE BETWEEN TERMINAL ROW CENTERS THE DISTANCE BETWEEN THE TERMINAL ROW CENTERS. 1D AND 1B MODE REPLY11AA05 ABCVD /D/ 09MATERIAL,BOARD BOARD MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BOARD IS FABRICATED. PLEASE USE MRC MATT IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 ABCWD /D/ 17TREATMENT,SURFACE,BOARD BOARD SURFACE TREATMENT ANY ADDITION, TREATMENT, OR ALTERNATION OF THE BOARD MATERIAL FOR THE PURPOSE OF ENVIRONMENTAL PROTECTION, DECORATION, OR INCREASED ELECTRICAL CONDUCTIVITY. SELECT REPLY CODE 10AD09 ABCXD 19CONSTRUCTION,BOARD BOARD CONSTRUCTION THE STRUCTURAL CHARACTERISTIC(S) OF THE BOARD. SELECT REPLY CODE 10AB20 ABCYA /D/ 12QUANTITY,SECTION SECTION QUANTITY THE NUMBER OF SECTIONS WHICH COMPRISE A SCORED TERMINAL BOARD. 1A MODE REPLY 0 ABCZA 12QUANTITY PER SECTION,FACILITY,TERMINAL TERMINAL FACILITY QUANTITY PER SECTION THE NUMBER OF TERMINAL FACILITIES PROVIDED IN EACH SECTION OF A SCORED TERMINAL BOARD WITHOUT TERMINALS. 1A MODE REPLY 0 ABDAA 12QUANTITY PER SECTION,TERMINAL TERMINAL QUANTITY PER SECTION THE NUMBER OF TERMINALS FURNISHED IN EACH SECTION OF A SCORED TERMINAL BOARD. 1A MODE REPLY 0 ABDBA 12QUANTITY,FACILITY,TERMINAL TERMINAL FACILITY QUANTITY THE NUMBER OF FACILITIES PROVIDED ON THE ITEM FOR THE INSTALLATION OF TERMINALS. 1A MODE REPLY 0 ABDCA /D/ 12QUANTITY,TERMINAL,NONFEEDTHRU NONFEEDTHRU TERMINAL QUANTITY THE NUMBER OF NONFEEDTHRU TERMINAL(S) FURNISHED WITH THE ITEM. 1A MODE REPLY 0 ABDDA /D/ 16STYLE,TERMINAL,NONFEEDTHRU NONFEEDTHRU TERMINAL STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE NONFEEDTHRU TERMINALS. 1A MODE REPLY 0 ABDEA /D/ 12QUANTITY,TERMINAL,FEEDTHRU FEEDTHRU TERMINAL QUANTITY THE NUMBER OF FEEDTHRU TERMINAL(S) FURNISHED WITH THE ITEM. 1A MODE REPLY 0 ABDFA /D/ 16STYLE,END,CONNECTION,FEEDTHRU,FIRST FIRST FEEDTHRU CONNECTION END STYLE THE STYLE OF WIRE, OR OTHER CONDUCTOR, CONNECTION FACILITY FURNISHED ON A FEEDTHRU TERMINAL ON THE END OPPOSITE THE FEEDTHRU CONNECTION END. 1A MODE REPLY 0 ABDGA /D/ 16STYLE,END,CONNECTION,FEEDTHRU,SECOND SECOND FEEDTHRU CONNECTION END STYLE (A)THE END OF THE FEEDTHRU TERMINAL WHICH PASSES THROUGH THE HORIZONTAL PLANE OF THE TERMINAL BOARD OPPOSITE THE BARRIERS, OR (B)THAT END OF THE FEEDTHRU TERMINAL WHICH PASSES THROUGH THE HORIZONTAL PLANE OF THE TERMINAL BOARD ADJACENT TO THE STANDOFFS, OR (C)IF THE BOARD CAN BE MOUNTED IN ANY POSITION WITHOUT REGARD TO BARRIERS OR STANDOFFS, THE END OF THE FEEDTHRU TERMINAL WHICH CORRESPONDS TO THE HIGHER STYLE NUMBER FROM THE REFERENCE DRAWING. 1A MODE REPLY 0 ABDHA 12QUANTITY,RECEPTACLE,SINGLE FEEDTHRU SINGLE FEEDTHRU RECEPTACLE QUANTITY THE NUMBER OF SINGLE/UNCONNECTED/TAPER PIN FEEDTHRU RECEPTACLES PROVIDED IN THE TERMINAL BOARD. 1A MODE REPLY 0 ABDJA /D/ 12QUANTITY,SETS,RECEPTACLE,FEEDTHRU,COMMON COMMON FEEDTHRU RECEPTACLE SETS QUANTITY THE NUMBER OF SETS OF COMMON (CONNECTED) TAPER PIN FEEDTHRU RECEPTACLES PROVIDED IN THE TERMINAL BOARD. 1A MODE REPLY 0 ABDKA /D/ 12QUANTITY PER SET,RECEPTACLE,FEEDTHRU,COMMON COMMON FEEDTHRU RECEPTACLE QUANTITY PER SET THE NUMBER OF TAPER PIN RECEPTACLES WHICH COMPRISES A SET OF COMMON (CONNECTED) FEEDTHRU RECEPTACLES IN A TERMINAL BOARD. 1A MODE REPLY 0 ABDLA /D/ 16STYLE,DESIGN,STRIP,TERMINAL TERMINAL STRIP DESIGN STYLE THE SHAPE AND ARRANGEMENT OF THE TERMINAL(S) AND MOUNTING FOOT (FEET) HOLE(S). 1A MODE REPLY 0 ABDMD /D/ 09MATERIAL,TERMINAL TERMINAL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TERMINAL IS FABRICATED. SELECT REPLY CODE 10AD09 ABDND /D/ 17SURFACE TREATMENT,TERMINAL TERMINAL SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A TERMINAL SURFACE. SELECT REPLY CODE 10AD09 ABDPA /D/ 12QUANTITY,LINKS,CONNECTING,TERMINAL TERMINAL CONNECTING LINKS QUANTITY THE NUMBER OF TERMINAL CONNECTING LINKS FURNISHED WITH THE ITEM. 1A MODE REPLY 0 ABDQL /D/ 16STYLE,LINK,CONNECTING,TERMINAL TERMINAL CONNECTING LINK STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TERMINAL CONNECTING LINK. 1A MODE REPLY 0 ABDRD /D/ 19PROVISION,MOUNTING MOUNTING PROVISION THE PROVISION/S/ FOR MOUNTING THE ITEM. PLEASE USE MRC BHMS IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB21 ABDSA 12QUANTITY,PROVISION,MOUNTING MOUNTING PROVISION QUANTITY THE NUMBER OF MOUNTING PROVISIONS PROVIDED. 1A MODE REPLY 0 ABDTJ /D/A13THREAD SIZE,FACILITY,MOUNTING MOUNTING FACILITY THREAD SIZE THE THREAD SERIES,THREAD MAJOR/MAXIMUM DIAMETER,AND THE NUMBER OF THREADS PER MEASUREMENT SCALE ON THE MOUNTING FACILITY. 1D AND 1A MODE REPLY12AC21 ABDUJ 04DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO LENGTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ABDVJ 04DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ABDWJ 04DISTANCE FROM BOTTOM EDGE OF TERMINAL BOARD TO CENTER OF MOUNTING HOLE DISTANCE FROM BOTTOM EDGE OF TERMINAL BOARD TO CENTER OF MOUNTING HOLE NONE. 1D AND 1B MODE REPLY11AA05 ABDXJ 04DISTANCE FROM LEFT EDGE OF TERMINAL BOARD TO CENTER OF FIRST MOUNTING FACILITY DISTANCE FROM LEFT EDGE OF TERMINAL BOARD TO CENTER OF FIRST MOUNTING FACILITY NONE. 1D AND 1B MODE REPLY11AA05 ABDYJ 04DISTANCE FROM BOTTOM EDGE OF TERMINAL BOARD TO BOTTOM EDGE OF MOUNTING FOOT DISTANCE FROM BOTTOM EDGE OF TERMINAL BOARD TO BOTTOM EDGE OF MOUNTING FOOT NONE. 1D AND 1B MODE REPLY11AA05 ABDZB /D/ 10RATING IN KILOVOLTS,VOLTAGE,WITHSTANDING,DIELECTRIC DIELECTRIC WITHSTANDING VOLTAGE RATING IN KILOVOLTS THE MAXIMUM VOLTAGE, IN KILOVOLTS, WHICH THE INSULATING MATERIAL OF THE ITEM WILL WITHSTAND WITHOUT RESULTING IN DISRUPTIVE DISCHARGE OR DETERIORATION. 1B MODE REPLY 0 ABEAD /D/ 07HOLES,FANNING FANNING HOLES HOLES PROVIDED IN THE BASE OF THE ITEM FOR THE PURPOSE OF SEPARATING OR FANNING INCOMING WIRES/CABLES. SELECT REPLY CODE 10AB22 ABEBD /D/ 07SHIELDING,INTERFERENCE,RADIO RADIO INTERFERENCE SHIELDING SPECIAL SHIELDING OF THE ITEM AGAINST RADIO INTERFERENCE. SELECT REPLY CODE 10AB22 ABECD /D/ 18TYPE,STRIP,MARKER MARKER STRIP TYPE INDICATES THE TYPE OF MARKER STRIP FURNISHED WITH THE ITEM TO IDENTIFY THE TERMINALS; IT MAY BE PREMARKED WITH NUMERALS OR LETTERS, OR IT MAY BE BLANK SO THAT THE END USER MAY DESIGNATE THE TERMINALS AS REQUIRED. SELECT REPLY CODE 10AB23 ABEDA 12QUANTITY,DIAPHRAGM DIAPHRAGM QUANTITY THE NUMBER OF DIAPHRAGMS INCLUDED IN THE ITEM. 1A MODE REPLY 0 ABEEJ /D/ 04DIAMETER,OUTSIDE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AH03 ABEFJ /D/ 04DIAMETER,INSIDE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AH03 ABEGJ /D/ 04DISTANCE ACROSS POINTS OF HEXAGONAL SHOULDERS DISTANCE ACROSS POINTS OF HEXAGONAL SHOULDERS NONE. 2D AND 1B MODE REPLY21AA051AH03 ABEHJ /D/ 04DIAMETER AT SEAT END,INSIDE INSIDE DIAMETER AT SEAT END NONE. 2D AND 1B MODE REPLY21AA051AH03 ABEJJ /D/ 04DISTANCE FROM END OF LEG TO PLANE OF BEND DISTANCE FROM END OF LEG TO PLANE OF BEND NONE. 2D AND 1B MODE REPLY21AA051AH03 ABEKJ /D/ 04DIAMETER ACCOMMODATED,CABLE/WIRE CABLE/WIRE DIAMETER ACCOMMODATED NONE. 2D AND 1B MODE REPLY21AA051AH03 ABELJ /D/ 04LENGTH,LEG LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AH03 ABEMD /D/ 17SURFACE TREATMENT,BODY BODY SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A BODY SURFACE. PLEASE USE MRC SFTT AND ISAC THE BODY REPLY IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 ABENH /D/ 03DESIGNATION AND LOCATION,END,THREADED THREADED END DESIGNATION AND LOCATION AN INDICATION OF WHETHER THE ENDS ARE INTERNALLY OR EXTERNALLY THREADED.INCLUDES THE FITTING END DESIGNATOR. 2D MODE REPLY 21AH031AC22 ABEPD /D/ 09MATERIAL,STEM STEM MATERIAL THE ELEMENT, COMPOUND,OR MIXTURE OF WHICH THE STEM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC CYBN OR MATT AND USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 ABEQJ /D/ 13THREAD SIZE AND SERIES/TYPE DESIGNATOR THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE SCREW THREAD DIAMETER, THREAD SERIES/TYPE, AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE.INCLUDES THE FITTING END DESIGNATOR. 2D AND 1B MODE REPLY22AC211AH03 ABERJ /D/A13THREAD CLASS AND END DESIGNATOR THREAD CLASS AND END DESIGNATOR A DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD. 1D AND 1A MODE REPLY11AH03 ABESJ /D/T13THREAD PITCH DIAMETERS AND END DESIGNATOR THREAD PITCH DIAMETERS AND END DESIGNATOR THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.INCLUDES THE END DESIGNATOR. 2D AND 1F MODE REPLY21AA051AH03 ABETJ 13THREAD LENGTH THREAD LENGTH A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS. 1D AND 1B MODE REPLY11AA05 ABEUJ /D/ 13THREAD LENGTH AND END DESIGNATOR THREAD LENGTH AND END DESIGNATOR A MEASURE OF THE EXTENT OF COMPLETE (FULL) THREADS MEASURED ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS.INCLUDES THE END DESIGNATOR. 2D AND 1B MODE REPLY21AA051AH03 ABEVH /D/ 18TYPE,CONDUIT ACCOMMODATED CONDUIT ACCOMMODATED TYPE INDICATES THE TYPE OF CONDUIT ACCOMMODATED BY THE END CONFIGURATION.INCLUDES THE FITTING END DESIGNATOR. 2D MODE REPLY 21AC231AH03 ABEWJ /D/A16STYLE AND END DESIGNATOR,END END STYLE AND END DESIGNATOR A NUMERIC DESIGNATION APPLIED TO THE GENERAL PHYSICAL CONFIGURATION OF THE ITEM.INCLUDES THE FITTING END DESIGNATOR. 1D AND 1A MODE REPLY11AH03 ABEXJ 04ANGLE,DEFLECTION DEFLECTION ANGLE THE DEGREE OF DEFLECTION BETWEEN TWO STRAIGHT LINES OF A CIRCLE. 1D AND 1B MODE REPLY11AP38 ABEYD /D/ 14SHAPE,GRIPPING ACCOMMODATION GRIPPING ACCOMMODATION SHAPE THE PHYSICAL CONFIGURATION OF THAT PORTION OF AN ITEM USED AS A GRIPPING AID IN THE APPLICATION OF TORQUE. SELECT REPLY CODE 10AD07 ABEZD /D/ 18TYPE,ACCOMMODATION,GRIPPING GRIPPING ACCOMMODATION TYPE INDICATES THE TYPE OF GRIPPING ACCOMMODATION USED AS AN AID IN THE APPLICATION OF TORQUE. SELECT REPLY CODE 10AB24 ABFAD 11METHOD,CONNECTION,FERRULE FERRULE CONNECTION METHOD THE MEANS BY WHICH THE FERRULE IS CONNECTED. SELECT REPLY CODE 10AB25 ABFBD /D/ 14SHAPE,SURFACE,FERRULE CONTACT FERRULE CONTACT SURFACE SHAPE THE PHYSICAL CONFIGURATION OF THE CONTACT SURFACE OF THE FERRULE. SELECT REPLY CODE 10AD07 ABFCD 18TYPE,OPENING,FILLER HEAD FILLER HEAD OPENING TYPE INDICATES THE TYPE OF OPENING PROVIDED ON THE FILLER HEAD. SELECT REPLY CODE 10AB26 ABFDJ 10EXPANSION,LINEAR,MAXIMUM MAXIMUM LINEAR EXPANSION THE MAXIMUM AMOUNT OF LINEAR EXPANSION PROVIDED IN THE DESIGN OF THE ITEM. 1D AND 1B MODE REPLY11AA05 ABFED 19PROTECTION,HAZARDOUS LOCATIONS/ENVIRONMENTAL HAZARDOUS LOCATIONS/ENVIRONMENTAL PROTECTION THE SPECIFIC COMMERCIAL RATING WHICH CLASSES THE ITEM AS TO WHAT DEGREE THE ITEM WILL WITHSTAND ENVIRONMENTAL ELEMENTS AND/OR HAZARDOUS LOCATIONS. SELECT REPLY CODE 10AB27 ABFFD 19ITEMS,FURNISHED FURNISHED ITEMS ITEMS FURNISHED AS ACCESSORIES WHICH ARE NOT SPECIFIED ELSEWHERE. SELECT REPLY CODE 10AB28 ABFGD /D/ 18TYPE,SUPPRESSION,RADIO INTERFERENCE RADIO INTERFERENCE SUPPRESSION TYPE INDICATES THE TYPE OF DEVICE(S) INSTALLED ON OR AROUND THE EQUIPMENT WHICH ELIMINATES UNDESIRABLE RADIO INTERFERENCE WAVES. SELECT REPLY CODE 10AB29 ABFHG 08LOCATION,CONNECTION,FLUE FLUE CONNECTION LOCATION INDICATES THE LOCATION OF THE FLUE CONNECTION. FULL TEXT WRITE-IN 0 ABFJG /D/ 08LOCATION,CONNECTION DUCT CONNECTION DUCT LOCATION INDICATES THE LOCATION OF THE DUCT CONNECTION IN RELATIONSHIP TO THE OUTER BOUNDARIES OF THE DUCT TYPE HEATER. FULL TEXT WRITE-IN 0 ABFKJ 10EFFECTIVE AREA,DIAPHRAGM,SERVICE SERVICE DIAPHRAGM EFFECTIVE AREA A MEASUREMENT OF THE EFFECTIVE AREA OF THE SERVICE DIAPHRAGM. 1D AND 1B MODE REPLY12AG67 ABFLJ 10EFFECTIVE AREA,DIAPHRAGM,EMERGENCY EMERGENCY DIAPHRAGM EFFECTIVE AREA A MEASUREMENT OF THE EFFECTIVE AREA OF THE EMERGENCY DIAPHRAGM. 1D AND 1B MODE REPLY12AG67 ABFMJ A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,PUSH ROD PUSH ROD THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE PUSH ROD. 1D AND 1A MODE REPLY12AH06 ABFNH 19MARKING AND SURFACE FINISH,SCALE SCALE MARKING AND SURFACE FINISH AN INDICATION OF THE MARKING/S/ ON THE SCALE AND THE SURFACE FINISH. 2D MODE REPLY 23AJ653AB54 ABFPB /D/ 12QUANTITY PER MINUTE,LOAF,RATED RATED LOAF QUANTITY PER MINUTE THE RATED NUMBER OF LOAVES SLICED PER MINUTE. 1B MODE REPLY 0 ABFQJ 04LENGTH ACCOMMODATION,LOAF LOAF LENGTH ACCOMMODATION THE LONGEST LENGTH OF A LOAF THE ITEM WILL HANDLE. 2D AND 1B MODE REPLY21AA051AC20 ABFRA 12QUANTITY,HOLE,SETSCREW SETSCREW HOLE QUANTITY THE NUMBER OF SETSCREW HOLES INCLUDED ON THE ITEM. 1A MODE REPLY 0 ABFSJ /D/A13THREAD SIZE,HOLE,SCREW SCREW HOLE THREAD SIZE THE SCREW THREAD SERIES,SCREW THREAD MAJOR/MAXIMUM DIAMETER,AND THE NUMBER OF THREADS PER MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AC21 ABFTA /D/ 16STYLE,DRIVE,INTERNAL,SCREW SCREW INTERNAL DRIVE STYLE THE METHOD USED FOR DRIVING THE FASTENER INTO PLACE. 1A MODE REPLY 0 ABFUJ 04DISTANCE FROM HOLE CENTER TO KNOB/SKIRT BASE DISTANCE FROM HOLE CENTER TO KNOB/SKIRT BASE THE DISTANCE FROM THE CENTER OF THE HOLE TO THE BASE OF THE KNOB OR BASE OF SKIRT IF WITH INTEGRALLY MOLDED SKIRT. 2D AND 1B MODE REPLY21AA051AC20 ABFVJ /D/A13THREAD SIZE,RECEPTACLE RECEPTACLE THREAD SIZE THE SCREW THREAD SERIES, SCREW THREAD MAJOR/MAXIMUM DIAMETER, AND THE NUMBER OF THREADS PER MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AC21 ABFWJ /D/A13THREAD SIZE,STUD STUD THREAD SIZE THE SCREW THREAD SERIES, SCREW THREAD MAJOR/MAXIMUM DIAMETER, AND THE NUMBER OF THREADS PER MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AC21 ABFXL 16STYLE,STUD,UNTHREADED UNTHREADED STUD STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE UNTHREADED STUD. 1L MODE REPLY 0 ABFYJ 04DEPTH,OVERALL OVERALL DEPTH AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF AN ITEM,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 ABFZJ 04LENGTH,GROOVE GROOVE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE GROOVE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ABGAJ 04DEPTH,GROOVE GROOVE DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF A GROOVE,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 ABGBJ 04WIDTH ACROSS CORNERS WIDTH ACROSS CORNERS A MEASUREMENT OF THE DISTANCE DIAGONALLY FROM ONE CORNER TO THE OPPOSITE CORNER. 2D AND 1B MODE REPLY21AA051AC20 ABGCJ 04WIDTH,SLOT SLOT WIDTH THE DISTANCE,MEASURED ALONG A STRAIGHT LINE PERPENDICULAR TO THE LONGITUDINAL AXIS OF THE SLOT,FROM ONE EDGE TO THE OTHER. 2D AND 1B MODE REPLY21AA051AC20 ABGDJ 04LENGTH,SLOT SLOT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SLOT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ABGEJ 04DIAMETER,MINOR,TAPERED END TAPERED END MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABGFJ 04WIDTH,GROOVE GROOVE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A GROOVE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ABGGJ 04RADIUS RADIUS THE DISTANCE FROM THE CENTERLINE TO THE AXIS OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ABGHJ 04DIAMETER,STEP STEP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABGJJ 04LENGTH,STEP STEP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE STEP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ABGKB 04ANGLE IN DEG,TAPER TAPER ANGLE IN DEG NONE. 1B MODE REPLY 0 ABGLJ 04WIDTH WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ABGMB /D/ 04ANGLE IN DEG,SECTOR SECTOR ANGLE IN DEG NONE. 1B MODE REPLY 0 ABGNJ 04LENGTH,OVERALL,BOARD BOARD OVERALL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ABGPJ 04WIDTH,OVERALL,BOARD BOARD OVERALL WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ABGQJ 04HEIGHT,OVERALL,BOARD BOARD OVERALL HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 ABGRJ 04HEIGHT EXCLUDING TERMINALS,BOARD BOARD HEIGHT EXCLUDING TERMINALS NONE. 1D AND 1B MODE REPLY11AA05 ABGSJ 04THICKNESS,BASE BASE THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 ABGTJ 04THICKNESS,BOARD BOARD THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 ABGUD 18TYPE,ACCOMMODATION,PIN PIN ACCOMMODATION TYPE THE PARTICULAR SHAPE OF THE PIN ACCOMMODATION AND WHETHER OR NOT THE PIN IS INCLUDED. SELECT REPLY CODE 10AB30 ABGVJ 04DIAMETER,HOLE,STRAIGHT PIN STRAIGHT PIN HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A STRAIGHT PIN HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABGWD 19SIZE ACCOMMODATED,PIN,TAPERED TAPERED PIN SIZE ACCOMMODATED THE SIZE DESIGNATION OF THE TAPERED PIN THAT AN ITEM IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AB31 ABGXA 04SIZE,SCREW,WOOD WOOD SCREW SIZE DESIGNATES THE SIZE BY WHICH THE WOOD SCREW IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1A MODE REPLY 0 ABGYJ /D/ 04LENGTH,SCREW,WOOD WOOD SCREW LENGTH A MEASUREMENT OF THE LONGEST DIMENSION FROM THE BOTTOM OF THE KNOB TO THE SCREW POINT. 2D AND 1B MODE REPLY21AA051AC20 ABGZA /D/ 16STYLE,KNOB KNOB STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE KNOB. 1A MODE REPLY 0 ABHAA 12QUANTITY,FOIL,FLUTED FLUTED FOIL QUANTITY THE NUMBER OF CURVED INDENTATIONS SEPARATED BY GROOVES. 1A MODE REPLY 0 ABHBJ /D/ 04LENGTH,OVERALL OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ABHCJ /D/ 04WIDTH,OVERALL OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS. PLEASE USE MRC ABMK IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 ABHDJ /D/ 04THICKNESS,OVERALL OVERALL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABHEJ 04DIAMETER,OUTSIDE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABHFJ 04WIDTH ACROSS FLATS WIDTH ACROSS FLATS THE SHORTEST STRAIGHT LINE BETWEEN FLATS, PERPENDICULAR TO THE HEIGHT OF THE WRENCHING SURFACE. 2D AND 1B MODE REPLY21AA051AC20 ABHGD 19CONDITION,SURFACE,GRIPPING GRIPPING SURFACE CONDITION THE TEXTURE OF THAT PORTION OF THE ITEM WHICH IS DESIGNED TO BE GRASPED. SELECT REPLY CODE 10AB32 ABHHL 16STYLE,ACCOMMODATION,SHAFT SHAFT ACCOMMODATION STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SHAFT ACCOMMODATION. 1L MODE REPLY 0 ABHJJ 04DIAMETER,CIRCLE,CUTTING CUTTING CIRCLE DIAMETER THE DIAMETER OF THE CIRCLE THAT THE ITEM IS CAPABLE OF CUTTING. 2D AND 1B MODE REPLY21AA051AC20 ABHKB 04SIZE,TRADE TRADE SIZE THE STANDARD NOMINAL SIZE DESIGNATION THAT INDICATES A MORE SPECIFIC ACTUAL INSIDE DIAMETER OF THE ITEM. 1B MODE REPLY 0 ABHLD /D/ 18TYPE,CONDUIT CONDUIT TYPE INDICATES THE TYPE OF CONDUIT INCLUDED. SELECT REPLY CODE 10AB33 ABHMD /D/ 18TYPE,BEND BEND TYPE THE TERMINOLOGY USED TO DESIGNATE A PARTICULAR TYPE OF BEND IN AN ITEM. SELECT REPLY CODE 10AB34 ABHNJ /D/ 04DISTANCE,BEND,OFFSET OFFSET BEND DISTANCE NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 1D AND 1B MODE REPLY11AA05 ABHPJ 04LENGTH,OVERALL OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ABHQJ /D/ 04LENGTH LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ABHRJ /D/ 04DIAMETER,OUTSIDE OUTSIDE DIAMETER NONE. PLEASE USE MRC ABHE IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 ABHSJ 04LENGTH,HEATING,EFFECTIVE EFFECTIVE HEATING LENGTH THE LENGTH OF THAT PORTION OF THE HEATING ELEMENT THAT IMPARTS HEAT. 2D AND 1B MODE REPLY21AA051AC20 ABHTJ 04HEIGHT,RISER RISER HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ABHUJ 04DISTANCE,CLEARANCE,MINIMUM MINIMUM CLEARANCE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 ABHVJ 04DISTANCE FROM TERMINAL BOX DISTANCE FROM TERMINAL BOX NONE. 2D AND 1B MODE REPLY21AA051AC20 ABHWJ /D/ 04LENGTH LEG,VERTICAL VERTICAL LENGTH LEG NONE. 2D AND 1B MODE REPLY21AA051AC20 ABHXJ /D/ 04LENGTH LEG,HORIZONTAL HORIZONTAL LENGTH LEG NONE. 2D AND 1B MODE REPLY21AA051AC20 ABHYA 12QUANTITY,TURN TURN QUANTITY THE NUMBER OF TURNS OF CONDUCTIVE MATERIAL FORMING THE WINDING. 1A MODE REPLY 0 ABHZJ /D/ 04SIZE ACCOMMODATED,TRADE,CONDUIT CONDUIT TRADE SIZE ACCOMMODATED THE STANDARD NOMINAL SIZE DESIGNATION THAT INDICATES THE SPECIFIC ACTUAL INSIDE DIAMETER OF THE CONDUIT ACCOMMODATION, INCLUDING THE FITTING END DESIGNATOR. 2D AND 1B MODE REPLY21AA051AH03 ABJAD 19SPECTRUM,RADIATION,ELEMENT ELEMENT RADIATION SPECTRUM AN INDICATION OF THE RADIATION SPECTRUM OF THE ELEMENT. SELECT REPLY CODE 10AB35 ABJBD /D/ 09MATERIAL,WIRE,RESISTANCE RESISTANCE WIRE MATERIAL THE SUBSTANCE FROM WHICH THE RESISTANCE WIRE IS MANUFACTURED. SELECT REPLY CODE 10AD09 ABJCD /D/ 09MATERIAL,INSULATION,EMBEDDING/SUPPORT,WIRE,RESISTANCE RESISTANCE WIRE EMBEDDING/SUPPORT INSULATION MATERIAL THE SUBSTANCE FROM WHICH THE INSULATING MATERIAL IS MANUFACTURED, IN WHICH THE RESISTANCE WIRE IS EMBEDDED OR AFFIXED UPON FOR SUPPORT. SELECT REPLY CODE 10AD09 ABJDD /D/ 09MATERIAL,SHEATH SHEATH MATERIAL THE SUBSTANCE FROM WHICH THE SHEATH IS MANUFACTURED. THE SHEATH IS THE OUTER COVERING OF THE ELEMENT AND CONTAINS THE RESISTANCE WIRE AND EMBEDDING SUBSTANCE. SELECT REPLY CODE 10AD09 ABJED 07ATTACHMENTS,FURNISHED FURNISHED ATTACHMENTS THE ATTACHMENTS THAT ARE FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AB28 ABJFD 18TYPE,IMPURITIES,FEEDWATER FEEDWATER IMPURITIES TYPE INDICATES THE TYPE OF FEEDWATER IMPURITIES REMOVED BY THE UNIT. SELECT REPLY CODE 10AN91 ABJGJ /D/ 04SIZE FOR WHICH DESIGNED,HEADER,NOMINAL NOMINAL HEADER SIZE FOR WHICH DESIGNED THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL SIZE OF THE HEADER FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AA05 ABJHJ 10TEMP RATING TEMP RATING A VALUE WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AS APPLIED TO THE OPERATION,OR LIMITATION OF OPERATION,OF AN ITEM. 1D AND 1B MODE REPLY11AB36 ABJJA /D/ 12QUANTITY,DRAWER,HEATED HEATED DRAWER QUANTITY THE NUMBER OF DRAWERS THAT ARE ELECTRICALLY HEATED. 1A MODE REPLY 0 ABJKJ A18TYPE AND QUANTITY,DISPENSER DISPENSER TYPE AND QUANTITY INDICATES THE TYPE OF DISPENSER AND HOW MANY. 1D AND 1A MODE REPLY12AH83 ABJLB 10WATTAGE RATING IN WATTS WATTAGE RATING IN WATTS THE RATED POWER THAT AN ITEM CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS. 1B MODE REPLY 0 ABJMD 18TYPE,CONTROL,HEAT HEAT CONTROL TYPE INDICATES THE TYPE OF HEAT CONTROL INCLUDED ON THE ITEM. SELECT REPLY CODE 10AB37 ABJNJ T10RANGE,THERMOSTAT THERMOSTAT RANGE THE MINIMUM AND MAXIMUM TEMPERATURE RATINGS THROUGH WHICH THE THERMOSTAT WILL OPERATE. 1D AND 1F MODE REPLY11AB36 ABJPJ 04LENGTH,CABLE,POWER POWER CABLE LENGTH THE LENGTH MEASURED FROM THE ELEMENT TO THE EXTREME END OF THE POWER CABLE. 2D AND 1B MODE REPLY21AA051AC20 ABJQJ /D/ 04LENGTH,TUBE,FLEXIBLE FLEXIBLE TUBE LENGTH THE LENGTH MEASURED FROM THE ELECTRICAL ELEMENT TO THE EXTREME END OF THE TUBE 2D AND 1B MODE REPLY21AA051AC20 ABJRA /D/ 12QUANTITY,ELEMENT ELEMENT QUANTITY THE NUMBER OF ELECTRICAL HEATING ELEMENT(S) ON A COMMON MOUNTING. 1A MODE REPLY 0 ABJSL 16STYLE,CONNECTION,ELEMENT ELEMENT CONNECTION STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ELEMENT CONNECTION. 1L MODE REPLY 0 ABJTJ 04LENGTH,TERMINAL TERMINAL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A TERMINAL,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ABJUJ 04LENGTH,SHIELDING SHIELDING LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABJVL 16STYLE,ARRANGEMENT,TERMINAL TERMINAL ARRANGEMENT STYLE A NUMERIC DESIGNATION APPLIED TO THE LOCATION OF THE ELECTRICAL TERMINALS. 1L MODE REPLY 0 ABJWJ A18TYPE AND SIZE,CONTAINER CONTAINER TYPE AND SIZE INDICATES THE TYPE OF CONTAINER AND THE CAPACITY. 2D AND 1A MODE REPLY22AF722AG67 ABJXD 09MATERIAL,WHEEL WHEEL MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE WHEEL IS FABRICATED. SELECT REPLY CODE 10MA01 ABJYJ 04WIDTH,BASE,A-FRAME A-FRAME BASE WIDTH A MEASUREMENT OF THE WIDTH AT THE BASE OF THE A-FRAME. 2D AND 1B MODE REPLY21AA051AC20 ABJZJ 04THICKNESS,MOLDBOARD MOLDBOARD THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE WALL,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 ABKAJ A18TYPE AND QUANTITY,DRIVE DRIVE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF DRIVES PROVIDED. 1D AND 1A MODE REPLY13AK54 ABKBJ 19CAPABILITY,STORAGE,DRIVE DRIVE STORAGE CAPABILITY THE TOTAL STORAGE CAPABILITY OF THE DRIVE WITH ITS DESIGNATED DRIVE TYPE. 2D AND 1B MODE REPLY23AK542AG67 ABKCA 19NUMBER,IDENTIFYING,CYLINDER,TRANSPORTATION,DEPARTMENT OF DEPARTMENT OF TRANSPORTATION CYLINDER IDENTIFYING NUMBER A NUMBER ASSIGNED TO THE ITEM BY THE DEPARTMENT OF TRANSPORTATION TO IDENTIFY THE DESIGN SPECIFICATION AND SERVICE PRESSURE OF THE CYLINDER. 1A MODE REPLY 0 ABKDD 11METHOD,CONTROL CONTROL METHOD THE MEANS USED TO CONTROL THE OPERATION. SELECT REPLY CODE 10AC58 ABKEJ 10FORCE,COMPACTION COMPACTION FORCE THE OPERATION FORCE AT WHICH THE ITEM IS RATED FOR COMPACTION OF MATERIAL WITHIN THE DRUM. 1D AND 1B MODE REPLY11AN71 ABKFD 19PROTECTION,ENVIRONMENTAL,TERMINAL BOX TERMINAL BOX ENVIRONMENTAL PROTECTION THE ENVIRONMENTAL ELEMENTS WHICH A TERMINAL BOX IS DESIGNED TO WITHSTAND SATISFACTORILY. SELECT REPLY CODE 10AB38 ABKGJ 04DIAMETER,CIRCLE,BOLT BOLT CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABKHJ 04DIAMETER,BUSHING BUSHING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BUSHING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABKJJ 04DIAMETER,CASE CASE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CASE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABKKJ 04DIAMETER,FLANGE FLANGE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FLANGE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABKLJ /D/ 04DIAMETER,STAND-OFF STAND-OFF DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABKMJ 04DIAMETER,INSIDE,CLAMP CLAMP INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABKNJ 04HEIGHT,FACILITY,MOUNTING MOUNTING FACILITY HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ABKPJ 04LENGTH,FACILITY,MOUNTING MOUNTING FACILITY LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A MOUNTING FACILITY,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ABKQJ 04DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO LENGTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO LENGTH THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE LENGTH. 2D AND 1B MODE REPLY21AA051AC20 ABKRJ 04DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO WIDTH THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ABKSJ 04WIDTH,FACILITY,MOUNTING MOUNTING FACILITY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING FACILITY,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ABKTA /D/ 12QUANTITY,HOLE OR SLOT HOLE OR SLOT QUANTITY THE NUMBER OF HOLES OR SLOTS INCLUDED. 1A MODE REPLY 0 ABKUJ 04THICKNESS,FLANGE FLANGE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A FLANGE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ABKVJ 04DIAMETER,OUTSIDE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABKWJ 04HEIGHT,OVERALL OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 ABKXJ 04LENGTH,KEY,STRAIGHT,EXTERNAL EXTERNAL STRAIGHT KEY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABKYJ 04LENGTH,KEY,PREBENT,EXTERNAL EXTERNAL PREBENT KEY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABKZJ 04LENGTH,KEYWAY,EXTERNAL EXTERNAL KEYWAY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABLAJ 04LENGTH,KEY,PEENING PEENING KEY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABLBJ 04LENGTH,KEY,PREBENT,INTERNAL INTERNAL PREBENT KEY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABLCJ 04WIDTH,KEY,EXTERNAL STRAIGHT EXTERNAL STRAIGHT KEY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABLDJ 04WIDTH,KEY,EXTERNAL TAPERED EXTERNAL TAPERED KEY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABLEJ 04DIAMETER,CYLINDER,NOMINAL NOMINAL CYLINDER DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CYLINDER, AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ABLFJ 04WIDTH,KEY,EXTERNAL PREBENT EXTERNAL PREBENT KEY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABLGJ 04WIDTH,MINOR,TAPERED KEY TAPERED KEY MINOR WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABLHJ 04WIDTH,MAJOR,TAPERED KEY TAPERED KEY MAJOR WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABLJJ 04WIDTH,KEY,INTERNAL STRAIGHT INTERNAL STRAIGHT KEY WIDTH THE MEASUREMENT FROM ONE FLAT SURFACE OF THE KEY TO THE OPPOSITE FLAT SURFACE. 2D AND 1B MODE REPLY21AA051AC20 ABLKJ 04WIDTH,KEY,INTERNAL PREBENT INTERNAL PREBENT KEY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABLLJ 04WIDTH,KEYWAY,EXTERNAL EXTERNAL KEYWAY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN EXTERNAL KEYWAY,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ABLMJ 04WIDTH,KEYWAY,INTERNAL INTERNAL KEYWAY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN INTERNAL KEYWAY,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ABLNJ 04DISTANCE FROM OUTSIDE OF WASHER TO OFF-CENTER KEY,MINOR MINOR DISTANCE FROM OUTSIDE OF WASHER TO OFF-CENTER KEY NONE. 2D AND 1B MODE REPLY21AA051AC20 ABLPJ 04DISTANCE FROM OUTSIDE OF WASHER TO OFF-CENTER KEY,MAJOR MAJOR DISTANCE FROM OUTSIDE OF WASHER TO OFF-CENTER KEY NONE. 2D AND 1B MODE REPLY21AA051AC20 ABLQJ 04DISTANCE FROM CENTERLINE TO TOP OF INTERNAL KEY DISTANCE FROM CENTERLINE TO TOP OF INTERNAL KEY NONE. 2D AND 1B MODE REPLY21AA051AC20 ABLRJ 04DISTANCE FROM CENTERLINE TO BOTTOM OF INTERNAL KEYWAY DISTANCE FROM CENTERLINE TO BOTTOM OF INTERNAL KEYWAY NONE. 2D AND 1B MODE REPLY21AA051AC20 ABLSJ 04DISTANCE FROM CENTERLINE TO INSIDE OF PREBENT KEY DISTANCE FROM CENTERLINE TO INSIDE OF PREBENT KEY NONE. 2D AND 1B MODE REPLY21AA051AC20 ABLTB /D/ 04ANGLE BETWEEN EXTERNAL KEYS IN DEG ANGLE BETWEEN EXTERNAL KEYS IN DEG NONE. 1B MODE REPLY 0 ABLUB /D/ 04ANGLE IN DEG,KEY,EXTERNAL PREBENT EXTERNAL PREBENT KEY ANGLE IN DEG NONE. 1B MODE REPLY 0 ABLVB /D/ 04ANGLE IN DEG,PREBENT,INTERNAL INTERNAL PREBENT ANGLE IN DEG NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 1B MODE REPLY 0 ABLWJ 04DIAMETER,CIRCLE,KEY BASE KEY BASE CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABLXJ 04DISTANCE INCLUDING KEYS,OVERALL OVERALL DISTANCE INCLUDING KEYS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABLYJ 10CAPACITY,RESERVOIR,OIL OIL RESERVOIR CAPACITY THE AMOUNT OF FLUID THE RESERVOIR IS DESIGNED TO HOLD. 1D AND 1B MODE REPLY12AG67 ABLZJ 04DISTANCE BETWEEN THICK AND THIN EDGES,FLAT SIDE FLAT SIDE DISTANCE BETWEEN THICK AND THIN EDGES NONE. 2D AND 1B MODE REPLY21AA051AC20 ABMAJ /D/ 04WIDTH AT THICK EDGE WIDTH AT THICK EDGE NONE. 2D AND 1B MODE REPLY21AA051AC20 ABMBJ 04THICKNESS,MINOR MINOR THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABMCJ 04THICKNESS,MAJOR MAJOR THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABMDJ 04DIAMETER,RECESS RECESS DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE RECESS,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABMEB 04ANGLE IN DEG,RECESS RECESS ANGLE IN DEG NONE. 1B MODE REPLY 0 ABMFJ 04DISTANCE ACROSS SPLIT OPENING DISTANCE ACROSS SPLIT OPENING NONE. 2D AND 1B MODE REPLY21AA051AC20 ABMGJ 04HEIGHT,SHOULDER SHOULDER HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ABMHJ 04DEPTH,RECESS RECESS DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE RECESS,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 ABMJJ 04LENGTH ACROSS FLATS LENGTH ACROSS FLATS A MEASUREMENT OF THE LONGEST DIMENSION FROM ONE FLAT TO THE OPPOSITE FLAT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ABMKJ 04WIDTH,OVERALL OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ABMLJ /D/ 04DIAMETER,HOLE,THIRD THIRD HOLE DIAMETER PLEASE USE MRC AGML IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 ABMMJ 04LENGTH,KEY,SPLIT SPLIT KEY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABMNJ 04WIDTH,KEY,SMALL EXTERNAL PREBENT SMALL EXTERNAL PREBENT KEY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABMPJ 04THICKNESS AT BOLT HOLE THICKNESS AT BOLT HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 ABMQA 12QUANTITY,KEY,EXTERNAL EXTERNAL KEY QUANTITY NONE. 1A MODE REPLY 0 ABMRA 12QUANTITY,KEY,INTERNAL INTERNAL KEY QUANTITY THE NUMBER OF INTERNAL KEYS INCLUDED. 1A MODE REPLY 0 ABMSJ 04RADIUS AT SMALL END RADIUS AT SMALL END NONE. 2D AND 1B MODE REPLY21AA051AC20 ABMTJ 04RADIUS AT LARGE END RADIUS AT LARGE END NONE. 2D AND 1B MODE REPLY21AA051AC20 ABMUA 12QUANTITY,KEYWAY,EXTERNAL EXTERNAL KEYWAY QUANTITY NONE. 1A MODE REPLY 0 ABMVA 12QUANTITY,KEYWAY,INTERNAL INTERNAL KEYWAY QUANTITY THE NUMBER OF INTERNAL KEYWAYS INCLUDED. 1A MODE REPLY 0 ABMWL 16STYLE,SHAPE,PERIPHERAL PERIPHERAL SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE PERIPHERAL SHAPE OF THE ITEM. 1L MODE REPLY 0 ABMXL 16STYLE,SHAPE,CENTER HOLE CENTER HOLE SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE CENTER HOLE. 1L MODE REPLY 0 ABMYJ /D/A10MICROINCH FINISH AND SURFACE LOCATION DESIGNATOR MICROINCH FINISH AND SURFACE LOCATION DESIGNATOR DESIGNATES THE SPECIFIC MICROINCH FINISH AND A SURFACE LOCATION DESIGNATOR. 1D AND 1A MODE REPLY11AD10 ABMZJ 04DIAMETER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABNAJ 04LENGTH,UNDERLOOP UNDERLOOP LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABNBJ 04LENGTH,FLAT,FIRST FIRST FLAT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABNCJ 04HEIGHT,FLAT FLAT HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ABNDJ 04LENGTH,TAPER TAPER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TAPERED PORTION OF AN ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ABNEJ 04LENGTH,FLAT,SECOND SECOND FLAT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABNFJ 04LENGTH,END,ROUND ROUND END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABNGJ 04HEIGHT,TAPER TAPER HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE TAPERED PORTION OF AN ITEM,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 ABNHJ 04WIDTH,MINOR MINOR WIDTH THE SMALLEST MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ABNJB 04TAPER PER FOOT IN INCHES TAPER PER FOOT IN INCHES THE DIMINISHING MEASUREMENT OF THE DIAMETER ALONG THE MAJOR AXIS OF THE ITEM,EXPRESSED PER FOOT IN INCHES. 1B MODE REPLY 0 ABNKJ 04WIDTH,SHOULDER SHOULDER WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABNLJ 04DIAMETER,CIRCLE CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABNMJ 04THICKNESS THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ABNNJ /D/ 04HEIGHT,TYPE,ROUND BOTTOM ROUND BOTTOM TYPE HEIGHT NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 2D AND 1B MODE REPLY21AA051AC20 ABNPJ /D/ 04HEIGHT,TYPE,BOTTOM,FLAT FLAT BOTTOM TYPE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ABNQD 08LOCATION,SENSOR,POSITION,NOSEWHEEL NOSEWHEEL POSITION SENSOR LOCATION THE LOCATION OF THE NOSEWHEEL POSITION FEEDBACK SENSOR RELATIVE TO THE STEERING UNIT. SELECT REPLY CODE 10AK54 ABNRA 12QUANTITY,HEAT HEAT QUANTITY THE NUMBER OF HEATS AT WHICH THE ITEM WILL OPERATE. 1A MODE REPLY 0 ABNSJ /D/ 10DENSITY RATING,WATT WATT DENSITY RATING THE HEAT OUTPUT OF THE HEATED PORTION OF THE SURFACE AREA OF THE HEATING ELEMENT. 1D AND 1B MODE REPLY11AB39 ABNTJ 10SIZE,OPENING,CONDUIT CONDUIT OPENING SIZE NONE. 2D AND 1B MODE REPLY21AA051AC20 ABNUJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,STUD STUD THREAD SIZE AND SERIES/TYPE DESIGNATOR NONE. 1D AND 1A MODE REPLY12AC21 ABNVJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,SCREW SCREW THREAD SIZE AND SERIES/TYPE DESIGNATOR NONE. 1D AND 1A MODE REPLY12AC21 ABNWJ 04DISTANCE BETWEEN GEOMETRIC CENTER OF HEAD AND CENTERLINE OF SHANK/SHOULDER,OFFSET OFFSET DISTANCE BETWEEN GEOMETRIC CENTER OF HEAD AND CENTERLINE OF SHANK/SHOULDER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABNXJ 04DIAMETER,RELIEF UNDER HEAD RELIEF UNDER HEAD DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABNYJ 04LENGTH,RELIEF UNDER HEAD RELIEF UNDER HEAD LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABNZJ 04LENGTH,EFFECTIVE EFFECTIVE LENGTH A MEASUREMENT OF THE LONGEST EFFECTIVE DIMENSION OF AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 ABPAJ 04DIAMETER,UNDERCUT UNDERCUT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABPBJ 04LENGTH,UNDER HEAD UNDER HEAD LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABPCJ 04WIDTH,UNDERCUT UNDERCUT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABPDJ 04WIDTH,UNDERCUT,SECOND SECOND UNDERCUT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABPEJ 04RADIUS,UNDERCUT UNDERCUT RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABPFJ 04DIAMETER,UNDERCUT,SECOND SECOND UNDERCUT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABPGJ 04RADIUS,UNDERCUT,SECOND SECOND UNDERCUT RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABPHJ 04DIAMETER,END,SMALL SMALL END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALL END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABPJJ 04DIAMETER,END,LARGE LARGE END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGE END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABPKJ 04DIAMETER,INTERMEDIATE INTERMEDIATE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABPLJ /D/ 04LENGTH,GROOVE,LONGITUDINAL LONGITUDINAL GROOVE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABPMJ 04DIAMETER,BODY BODY DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABPNJ 04DIAMETER,STOCK,WIRE WIRE STOCK DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WIRE STOCK,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABPPJ 04WIDTH,OPENING OPENING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN OPENING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ABPQJ 04LENGTH,PRONG PRONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABPRJ 04DIAMETER,STEP,FIRST FIRST STEP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABPSJ 04LENGTH,STEP,FIRST FIRST STEP LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABPTJ 04DIAMETER,STEP,SECOND SECOND STEP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABPUJ 04LENGTH,STEP,SECOND SECOND STEP LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABPVJ 04DIAMETER,STEP,THIRD THIRD STEP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABPWJ 04LENGTH,STEP,THIRD THIRD STEP LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABPXJ 04THICKNESS,MATERIAL MATERIAL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE MATERIAL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ABPYJ 04DIAMETER,EXPANDED EXPANDED DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ITEM IN ITS EXPANDED POSITION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABPZJ 04RADIUS,END END RADIUS A MEASUREMENT OF A STRAIGHT LINE EXTENDING FROM THE CENTER OF A CIRCLE TO THE END. 2D AND 1B MODE REPLY21AA051AC20 ABQAJ 04DIAMETER,MINOR,TAPER TAPER MINOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST CIRCULAR CROSS SECTION OF THE TAPERED PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABQBJ 04DIAMETER,MAJOR,TAPER TAPER MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CIRCULAR CROSS SECTION OF THE TAPERED PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABQCJ 04DIAMETER,HANDLE,RING RING HANDLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABQDJ 04LENGTH UNDER WASHER,SHANK SHANK LENGTH UNDER WASHER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABQEJ /D/ 04LENGTH FROM DETENTS TO TAPERED END LENGTH FROM DETENTS TO TAPERED END NONE. 2D AND 1B MODE REPLY21AA051AC20 ABQFJ /D/ 04LENGTH FROM SHOULDER TO HEAD END LENGTH FROM SHOULDER TO HEAD END NONE. 2D AND 1B MODE REPLY21AA051AC20 ABQGJ 04DIAMETER,HANDLE,BUTTON BUTTON HANDLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABQHJ /D/ 04LENGTH FROM CENTER OF PIN TO END OF HANDLE LENGTH FROM CENTER OF PIN TO END OF HANDLE NONE. 2D AND 1B MODE REPLY21AA051AC20 ABQJL 16STYLE,POINT POINT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE POINT. 1L MODE REPLY 0 ABQKL 16STYLE,END END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END. 1L MODE REPLY 0 ABQLJ 04LENGTH,CHAMFER,END END CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 2D AND 1B MODE REPLY21AA051AC20 ABQMB 04ANGLE IN DEG,CHAMFER,END END CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 ABQNJ 04RADIUS,END,OVAL OVAL END RADIUS A MEASUREMENT OF A STRAIGHT LINE EXTENDING FROM THE CENTER OF A CIRCLE TO THE OVAL END. 2D AND 1B MODE REPLY21AA051AC20 ABQPJ /D/ 04RADIUS,END,RADIUS RADIUS END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABQQJ /D/ 04RADIUS,END,ROUND ROUND END RADIUS A MEASUREMENT OF A STRAIGHT LINE EXTENDING FROM THE CENTER OF A CIRCLE TO THE ROUND END. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 2D AND 1B MODE REPLY21AA051AC20 ABQRJ 04DIAMETER,MAJOR,COUNTERSINK COUNTERSINK MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MAJOR PORTION OF THE HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABQSB 04ANGLE IN DEG,HOLE,COUNTERSUNK COUNTERSUNK HOLE ANGLE IN DEG THE ANGLE OF THE CONICAL RECESS OF THE HOLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ABQTD /D/ 08LOCATION,STYLE,END END STYLE LOCATION INDICATES THE LOCATION OF THE END STYLE FEATURE OF AN ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. SELECT REPLY CODE 10AE46 ABQUJ 04DEPTH,DRIVE POINT DRIVE POINT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABQVD 18TYPE,STRUT,SHOCK SHOCK STRUT TYPE INDICATES THE TYPE OF SHOCK STRUT INSTALLATION FOR WHICH THE PISTON IS DESIGNED. SELECT REPLY CODE 10AK54 ABQWJ 04LENGTH,HEAD HEAD LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABQXJ 04WIDTH,HEAD HEAD WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A HEAD,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ABQYB /D/ 04ANGLE IN DEG,CHAMFER,PIN PIN CHAMFER ANGLE IN DEG NONE. PLEASE USE MRC AATE WITH ISAC 0368 IN PLACE OF THIS DISCONTINUED MRC 01/12/2024. 1B MODE REPLY 0 ABQZL 16STYLE,DRIVE,INTERNAL INTERNAL DRIVE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE INTERNAL DRIVE. 1L MODE REPLY 0 ABRAJ A10CAPACITY OF THE WORKING MEMORY,REQUIRED REQUIRED CAPACITY OF THE WORKING MEMORY THE AMOUNT OF MEMORY WHICH MUST BE AVAILABLE IN ORDER FOR THE PROGRAM TO FUNCTION. 1D AND 1A MODE REPLY12AG67 ABRBL 16STYLE,ARRANGEMENT,HOLE HOLE ARRANGEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE HOLES. 1L MODE REPLY 0 ABRCJ 04DIAMETER,HOLE,FIRST FIRST HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABRDJ 04DIAMETER,HOLE,SECOND SECOND HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABREJ 04DISTANCE FROM CENTERLINE OF HOLE TO END OF PIN DISTANCE FROM CENTERLINE OF HOLE TO END OF PIN NONE. 2D AND 1B MODE REPLY21AA051AC20 ABRFJ 04DISTANCE BETWEEN HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN HOLES THE CENTER TO CENTER DISTANCE BETWEEN HOLES ON THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ABRGB /D/ 04ANGLE BETWEEN CENTERLINES OF HOLES IN DEG ANGLE BETWEEN CENTERLINES OF HOLES IN DEG NONE. 1B MODE REPLY 0 ABRHD /D/ 08LOCATION,HOLE HOLE LOCATION INDICATES THE LOCATION OF THE HOLES IN RESPECT TO THE ENDS OF THE ITEM. SELECT REPLY CODE 10AE46 ABRJD /D/ 18TYPE,ACTUATION ACTUATION TYPE INDICATES THE TYPE OF METHOD UTILIZED TO MECHANICALLY ACTIVATE A QUICK RELEASE PIN. SELECT REPLY CODE 10AB40 ABRKD /D/ 19MECHANISM,RELEASE RELEASE MECHANISM A BUTTON PROTRUDING FROM THE HANDLE OR HEAD,OR LOCATED BELOW THE SURFACE OF THE HEAD AND ACTIVATED BY A CAM-LEVER HANDLE.IT ACTIVATES THE SPINDLE WHICH PERMITS THE DETENTS TO RETRACT ALLOWING THE PIN TO BE INSERTED OR WITHDRAWN. SELECT REPLY CODE 10AB41 ABRLD /D/ 19FEATURE,DRIVE OUT DRIVE OUT FEATURE THE DESIGN FEATURE THAT ALLOWS THE LOCKING DETENTS TO RETRACT INTO THE SHANK OF THE PIN WHEN THE SPINDLE RECEIVES A SHARP BLOW. SELECT REPLY CODE 10AB42 ABRMA 12QUANTITY,DETENT DETENT QUANTITY THE NUMBER OF DETENTS INCLUDED IN THE ITEM. 1A MODE REPLY 0 ABRNJ 04HEIGHT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN OBJECT,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 ABRPJ /D/ 04DEPTH,OVERALL OVERALL DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABRQJ /D/ 04LENGTH,GROOVE GROOVE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABRRJ 04WIDTH,KEYWAY KEYWAY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A KEYWAY,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ABRSJ 04WIDTH ACROSS FLATS WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABRTJ /D/ 04WIDTH ACROSS CORNERS WIDTH ACROSS CORNERS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABRUJ 04WIDTH,SLOT SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABRVJ 04DEPTH,KEYWAY KEYWAY DEPTH A MEASUREMENT FROM THE TOP SURFACE TO THE BOTTOM OF THE KEYWAY GROOVE. 2D AND 1B MODE REPLY21AA051AC20 ABRWJ /D/ 04LENGTH,SLOT SLOT LENGTH NONE. PLEASE USE MRC ABGD IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 ABRXJ /D/ 04DIAMETER,MINOR,END,TAPERED TAPERED END MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABRYJ 04LENGTH LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF ANY OBJECT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ABRZJ /D/ 04WIDTH,GROOVE GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABSAA 12QUANTITY,SPLINE SPLINE QUANTITY THE NUMBER OF SPLINES ON OR IN THE ITEM. 1A MODE REPLY 0 ABSBJ /D/ 04WIDTH,SPLINE SPLINE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABSCJ /D/ 04DIAMETER,MINOR,SPLINE SPLINE MINOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST CROSS SECTION OF A SPLINE,AND TERMINATES AT THE CIRCUMFERENCE. PLEASE USE MRC AAUH IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 ABSDJ 04RADIUS RADIUS A STRAIGHT LINE EXTENDING FROM THE CENTER OF A CIRCLE TO THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABSEB /D/ 04ANGLE IN DEG,TAPER TAPER ANGLE IN DEG NONE. 1B MODE REPLY 0 ABSFJ 04WIDTH,KEY KEY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A KEY,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ABSGJ 04WIDTH WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABSHB /D/ 04ANGLE IN DEG,SECTOR SECTOR ANGLE IN DEG NONE. 1B MODE REPLY 0 ABSJJ 04DEPTH,KEY KEY DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE KEY,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 ABSKD /D/ 18TYPE,SKIRT SKIRT TYPE INDICATES THE TYPE OF SKIRT THAT IS PART OF THE KNOB,INTEGRALLY MOLDED OR MECHANICALLY ATTACHED,AND IS UTILIZED FOR COVERING OR PARTIALLY COVERING PROTRUDING MOUNTING HARDWARE,BUSHINGS,AND THE LIKE. SELECT REPLY CODE 10AB43 ABSLL 16STYLE,SKIRT SKIRT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SKIRT. 1L MODE REPLY 0 ABSMA /D/ 16STYLE,SHANK SHANK STYLE THE MECHANICALLY ATTACHED OR INTEGRALLY MOLDED PORTION OF THE KNOB LOCATED BELOW THE BASIC KNOB SHAPE. IT MAY CONTAIN THE SKIRT RECESS. IT IS NOT A GRIPPING SURFACE. 1A MODE REPLY 0 ABSNJ 04RADIUS,SHANK SHANK RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABSPD 19MARKING,REFERENCE REFERENCE MARKING A VISIBLE TRACING OR IMPRESSION,AND THE LIKE,OF ALPHA AND/OR NUMERIC CHARACTERS,SYMBOLS,AND THE LIKE. SELECT REPLY CODE 10AB44 ABSQD /D/ 18TYPE,POINTER POINTER TYPE INDICATES THE TYPE OF KNOB PART USED TO DIRECT ATTENTION TO A PARTICULAR POSITION. SELECT REPLY CODE 10AB45 ABSRJ 04LENGTH,OVERALL,POINTER POINTER OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE POINTER. 2D AND 1B MODE REPLY21AA051AC20 ABSSJ 04DISTANCE TO POINTER END DISTANCE TO POINTER END THE DISTANCE FROM CENTERLINE OF THE SHAFT OR SHAFT HOLE TO THE END OF THE POINTER. 2D AND 1B MODE REPLY21AA051AC20 ABSTD /D/ 08LOCATION,COLOR COLOR LOCATION INDICATES THE LOCATION OF AN ITEM TO WHICH THE COLOR IS APPLIED. SELECT REPLY CODE 10AE46 ABSUD /D/ 18TYPE,INSERT INSERT TYPE INDICATES THE TYPE OF ELEMENT INSERTED IN THE KNOB THAT ENABLES THE KNOB TO RETAIN THE SHAFT. SELECT REPLY CODE 10AC29 ABSVD /D/ 08LOCATION,MATERIAL MATERIAL LOCATION THE DESIGNATION OF THAT PORTION OF AN ITEM TO WHICH A SPECIFIC MATERIAL IS APPLICABLE. SELECT REPLY CODE 10AE46 ABSWD 19LUSTER,SURFACE SURFACE LUSTER THE APPEARANCE OF THE SURFACE OF AN ITEM AS TO ITS REFLECTING QUALITIES. SELECT REPLY CODE 10AB46 ABSXD 11METHOD,ATTACHMENT ATTACHMENT METHOD THE MEANS USED TO ATTACH THE ITEM. SELECT REPLY CODE 10AB47 ABSYJ /D/ 04DIAMETER,INSIDE,NOMINAL,CONDUIT CONDUIT NOMINAL INSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ABSZJ /D/ 04DIAMETER,OVERALL OVERALL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABTAJ /D/ 04THICKNESS,OVERALL OVERALL THICKNESS NONE. PLEASE USE MRC ADUM IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 ABTBJ 04DIAMETER,HOLE,MOUNTING MOUNTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABTCJ 04DIAMETER,MOUNTING FEATURE MOUNTING FEATURE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING FEATURE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABTDJ 04WIDTH,SLOT,MOUNTING MOUNTING SLOT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING SLOT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ABTEJ /D/ 04DIAMETER,OVERALL OVERALL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABTFJ /D/ 04HEIGHT,OVERALL OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ABTGJ /D/ 04RADIUS,EDGE,OUTSIDE OUTSIDE EDGE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABTHJ 04DISTANCE BETWEEN MOUNTING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES THE CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES. 2D AND 1B MODE REPLY21AA051AC20 ABTJA 12QUANTITY,HOLE,MOUNTING MOUNTING HOLE QUANTITY THE NUMBER OF MOUNTING HOLES PROVIDED. 1A MODE REPLY 0 ABTKJ /D/ 04WIDTH WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABTLJ 04LENGTH LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABTMJ /D/ 04RADIUS,WINDOW WINDOW RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABTNJ /D/ 04DIAMETER,HOLE,MOUNTING MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABTPJ /D/ 04RADIUS OF MOUNTING HOLE CENTERS RADIUS OF MOUNTING HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABTQA /D/ 12QUANTITY,HOLE,MOUNTING MOUNTING HOLE QUANTITY NONE. 1A MODE REPLY 0 ABTRJ /D/ 04DIAMETER,HOLE,MOUNTING MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABTSJ /D/ 04DISTANCE BETWEEN MOUNTING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 ABTTJ /D/ 04DIAMETER,OVERALL OVERALL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABTUJ /D/ 04HEIGHT,OVERALL OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ABTVJ 04DIAMETER,PORTION,KNOB KNOB PORTION DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABTWJ 04HEIGHT,PORTION,KNOB KNOB PORTION HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ABTXJ 04HEIGHT,DRUM DRUM HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ABTYJ /D/ 04DIAMETER,OVERALL OVERALL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABTZJ 04LENGTH,OVERALL OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABUAJ /D/ 04WIDTH,OVERALL OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABUBJ /D/ 04HEIGHT,OVERALL OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ABUCJ 04DIAMETER,HOLE,MOUNTING MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABUDA /D/ 12QUANTITY,HOLE,MOUNTING MOUNTING HOLE QUANTITY NONE. 1A MODE REPLY 0 ABUEJ /D/ 04DISTANCE BETWEEN MOUNTING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 ABUFB /D/ 04ANGLE OF MOUNTING HOLE IN DEG ANGLE OF MOUNTING HOLE IN DEG NONE. PLEASE USE MRC CSXS IN PLACE OF THIS DISCONTINUED MRC. 1B MODE REPLY 0 ABUGJ /D/ 04RADIUS RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABUHJ 04RADIUS,CIRCLE,MOUNTING HOLE MOUNTING HOLE CIRCLE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABUJA 13THREAD SIZE THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1A MODE REPLY 0 ABUKJ /D/ 04DIAMETER,OVERALL OVERALL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABULJ /D/ 04LENGTH,OVERALL OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABUMJ /D/ 04THICKNESS,MATERIAL MATERIAL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABUNJ /D/ 04RADIUS,CIRCLE,HOLE,MOUNTING MOUNTING HOLE CIRCLE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABUPJ /D/ 04HEIGHT,OVERALL OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ABUQJ 04DISTANCE BETWEEN MOUNTING HOLES,CENTER TO CENTER,FIRST FIRST CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 ABURJ 04DISTANCE BETWEEN MOUNTING HOLES,CENTER TO CENTER,SECOND SECOND CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 ABUSJ 10POWER RATING POWER RATING AN INDICATION OF THE RATED POWER OF THE ITEM. 1D AND 1B MODE REPLY11AC33 ABUTJ 10POWER REQUIRED POWER REQUIRED THE POWER REQUIRED TO OPERATE THE ITEM. 1D AND 1B MODE REPLY11AC33 ABUUJ /D/ 04DIAMETER,HOLE,MOUNTING MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABUVA /D/ 12QUANTITY,HOLE,MOUNTING MOUNTING HOLE QUANTITY NONE. 1A MODE REPLY 0 ABUWJ /D/ 04LENGTH,OVERALL OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABUXJ /D/ 04DIAMETER,OVERALL OVERALL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABUYJ 04DISTANCE FROM MOUNTING HOLE CENTER TO END OF POINTER DISTANCE FROM MOUNTING HOLE CENTER TO END OF POINTER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABUZJ /D/ 04WIDTH,OVERALL OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABVAJ 04LENGTH,PORTION,UNTHREADED UNTHREADED PORTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABVBA /D/ 12QUANTITY,HOLE,MOUNTING MOUNTING HOLE QUANTITY NONE. 1A MODE REPLY 0 ABVCJ /D/ 04DIAMETER,HOLE,MOUNTING MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABVDJ /D/ 04DISTANCE BETWEEN MOUNTING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 ABVEJ /D/ 04RADIUS RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABVFB /D/ 04ANGLE IN DEG,POINTER POINTER ANGLE IN DEG NONE. 1B MODE REPLY 0 ABVGJ 04LENGTH,SLOT,MOUNTING MOUNTING SLOT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING SLOT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ABVHJ /D/ 04WIDTH,SLOT,MOUNTING MOUNTING SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABVJB 04ANGLE BETWEEN CENTERLINES OF MOUNTING HOLES IN DEG ANGLE BETWEEN CENTERLINES OF MOUNTING HOLES IN DEG A MEASUREMENT OF THE AMOUNT OF TURNING NECESSARY TO BRING ONE HALF INTO COINCIDENCE WITH ANOTHER,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ABVKA 13THREAD SIZE DESIGNATOR THREAD SIZE DESIGNATOR DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1A MODE REPLY 0 ABVLJ 04DIAMETER,APERTURE APERTURE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN APERTURE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABVMJ 04DIAMETER,SHAFT,ACCOMMODATED ACCOMMODATED SHAFT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE SHAFT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABVNJ /D/ 04WIDTH,OVERALL OVERALL WIDTH PLEASE USE MRC ABMK IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 ABVPJ /D/ 04DIAMETER,OVERALL OVERALL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABVQJ /D/ 04RADIUS RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABVRJ /D/ 04THICKNESS,MATERIAL MATERIAL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABVSJ /D/ 04LENGTH,OVERALL OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABVTJ 04DIAMETER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ITEM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABVUJ /D/ 04WIDTH WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABVVJ 04DIAMETER,PIN PIN DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PIN,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABVWJ /D/ 04DIAMETER,OVERALL OVERALL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABVXJ /D/ 04THICKNESS,MATERIAL MATERIAL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABVYJ /D/ 04WIDTH,OVERALL OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABVZJ /D/ 04LENGTH, OVERALL OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABWAJ /D/ 04RADIUS RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABWBD /D/ 18TYPE,DIAL DIAL TYPE THE TERMINOLOGY USED TO IDENTIFY THE PARTICULAR RELATIONSHIP OF A SCALE OR POINTER TO A KNOB. SELECT REPLY CODE 10AB48 ABWCD 19INSCRIPTION,UNIT OF MEASURE,SCALE SCALE UNIT OF MEASURE INSCRIPTION THE STANDARD OF VALUATION AS REPRESENTED BY THE INSCRIPTION. SELECT REPLY CODE 10AB49 ABWDJ /D/A05DIRECTION AND RANGE,SCALE SCALE DIRECTION AND RANGE THE ORDER OF THE NUMERIC SCALE MARKINGS OF THE DIAL. 1D AND 1A MODE REPLY11AB50 ABWEJ /D/ 04DISTANCE AND TYPE,SCALE SCALE DISTANCE AND TYPE THE DISTANCE AND TYPE COVERED BY THE SCALE INSCRIPTION RANGE. 2D AND 1B MODE REPLY21AA051AC25 ABWFD 10LINEARITY,SCALE SCALE LINEARITY EQUAL OR UNEQUAL DISTANCES BETWEEN GRADUATIONS REPRESENTING VALUES OF MEASUREMENT ON A SCALE. SELECT REPLY CODE 10AB51 ABWGA 12QUANTITY,DIVISION,SCALE SCALE DIVISION QUANTITY THE NUMBER OF SCALE DIVISIONS. 1A MODE REPLY 0 ABWHD /D/ 19FACILITY,SELF-ILLUMINATION SELF-ILLUMINATION FACILITY THE MEANS PROVIDED TO ILLUMINATE THE DIAL WITHIN THE ITEM. SELECT REPLY CODE 10AB52 ABWJJ 04DIAMETER,MAXIMUM,ITEM ACCOMMODATED ITEM ACCOMMODATED MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED ITEM,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ABWKJ 04THICKNESS,MAXIMUM,ITEM ACCOMMODATED ITEM ACCOMMODATED MAXIMUM THICKNESS THE MAXIMUM MEASUREMENT OF THE SMALLEST DIMENSION OF THE ACCOMMODATED ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 ABWLD 18TYPE,ADJUSTMENT,LOCKING LOCKING ADJUSTMENT TYPE INDICATES THE TYPE OF TIGHTENING DEVICE FOR LOCKING THE ITEM. SELECT REPLY CODE 10AB53 ABWMA 12QUANTITY,SLOT,DIAL OBSERVATION DIAL OBSERVATION SLOT QUANTITY THE NUMBER OF SLOTS FOR OBSERVATION OF THE DIAL. 1A MODE REPLY 0 ABWND /D/ 19TRANSPARENCY,MATERIAL MATERIAL TRANSPARENCY THE ABILITY OF THE MATERIAL TO TRANSMIT LIGHT AND ALLOW VISUAL PERCEPTION. SELECT REPLY CODE 10AD56 ABWPD /D/ 07FRAME FRAME AN INDICATION OF WHETHER OR NOT A FRAME IS INCLUDED.PLEASE USE MRC CBBL IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 ABWQD /D/ 18TYPE,MARKING,LUMINOUS LUMINOUS MARKING TYPE INDICATES THE TYPE OF LUMINOUS MARKING(S) ON THE ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. SELECT REPLY CODE 10AB54 ABWRD /D/ 18TYPE,DRIVE DRIVE TYPE INDICATES THE TYPE OF DRIVE FOR TURNING,ROTATING,OR POSITIONING THE MECHANISM. SELECT REPLY CODE 10AB55 ABWSJ 10RATIO,DRIVE DRIVE RATIO THE NUMBER OF TURNS OF THE DIAL IN RELATION TO ONE TURN OF THE KNOB OR OTHER ACTUATING MECHANISM. 1D AND 1B MODE REPLY11AB56 ABWTJ 04LENGTH,OVERALL,BUSHING BUSHING OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABWUJ 04WIDTH ACROSS BUSHING FLATS WIDTH ACROSS BUSHING FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 ABWVJ 04DIAMETER,SHAFT SHAFT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHAFT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABWWJ 04LENGTH,EXTENSION,REAR SHAFT REAR SHAFT EXTENSION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABWXJ /D/ 04WIDTH,FLAT,FIRST SHAFT FIRST SHAFT FLAT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABWYJ /D/ 04WIDTH,FLAT,SECOND SHAFT SECOND SHAFT FLAT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABWZJ /D/ 04LENGTH,FLAT,FIRST SHAFT FIRST SHAFT FLAT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABXAJ /D/ 04LENGTH,FLAT,SECOND SHAFT SECOND SHAFT FLAT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABXBJ 04LENGTH,OVERALL,SHAFT SHAFT OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE SHAFT. 2D AND 1B MODE REPLY21AA051AC20 ABXCA /D/ 13THREAD SIZE DESIGNATOR,BUSHING BUSHING THREAD SIZE DESIGNATOR NONE. 1A MODE REPLY 0 ABXDJ 04LENGTH,BUSHING BUSHING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A BUSHING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ABXEJ /D/ 04DIAMETER,SHAFT SHAFT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABXFJ 04LENGTH,SHAFT SHAFT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SHAFT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ABXGJ /D/ 04LENGTH,OVERALL OVERALL LENGTH PLEASE USE MRC ABHP IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 ABXHJ /D/ 04DIAMETER,OVERALL OVERALL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABXJJ /D/ 04DIAMETER,OVERALL OVERALL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABXKJ /D/ 04LENGTH,OVERALL OVERALL LENGTH NONE. PLEASE USE MRC ABHP IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 ABXLJ 04DISTANCE FROM FLAT TO FLAT DISTANCE FROM FLAT TO FLAT A MEASUREMENT OF THE FLAT TO FLAT DISTANCE ALONG THE WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ABXMJ 04DIAMETER,END,SHAFT SHAFT END DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ABXNJ 04DEPTH,SOCKET SOCKET DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE SOCKET,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 ABXPJ 04DIAMETER,SOCKET SOCKET DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SOCKET,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABXQJ 04LENGTH,PORTION,FLATTED FLATTED PORTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABXRA 13THREAD SIZE DESIGNATOR,INTERNAL INTERNAL THREAD SIZE DESIGNATOR DESIGNATES THE THREAD DIAMETER AND NUMBER OF INTERNAL THREADS PER MEASUREMENT SCALE. 1A MODE REPLY 0 ABXSA 13THREAD SIZE DESIGNATOR,EXTERNAL EXTERNAL THREAD SIZE DESIGNATOR DESIGNATES THE THREAD DIAMETER AND NUMBER OF EXTERNAL THREADS PER MEASUREMENT SCALE. 1A MODE REPLY 0 ABXTJ 04THREAD LENGTH,INTERNAL INTERNAL THREAD LENGTH A MEASUREMENT OF THE EXTENT OF INTERNAL THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS. 2D AND 1B MODE REPLY21AA051AC20 ABXUJ 04THREAD LENGTH,EXTERNAL EXTERNAL THREAD LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ABXVJ 04DIAMETER,BORE BORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR BORE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ABXWD /D/ 18TYPE,END END TYPE THE TERMINOLOGY USED TO INDICATE THE TYPE OF CONNECTING TERMINALS OF THE ITEM. SELECT REPLY CODE 10AB57 ABXXJ /D/A13THREAD SIZE,BUSHING BUSHING THREAD SIZE THE THREAD SERIES, THREAD MAJOR/MAXIMUM DIAMETER, AND THE NUMBER OF THREADS PER MEASUREMENT SCALE OF A BUSHING. 1D AND 1A MODE REPLY12AC21 ABXYD /D/ 18TYPE,LOCK,SHAFT SHAFT LOCK TYPE INDICATES THE TYPE OF DEVICE USED TO SECURE THE SHAFT IN A FIXED POSITION. SELECT REPLY CODE 10AB58 ABXZJ 10VOLTAGE RATING,WITHSTANDING,DIELECTRIC DIELECTRIC WITHSTANDING VOLTAGE RATING THE MAXIMUM VOLTAGE IN VOLTS,MULTIPLES OR SUBMULTIPLES OF VOLTS,WHICH THE INSULATING MATERIALS OF THE ITEM WILL WITHSTAND WITHOUT RESULTING IN DISRUPTIVE DISCHARGE OR DETERIORATION. 1D AND 1B MODE REPLY11AB63 ABYAD /D/ 18TYPE,DEVICE,ATTACHMENT ATTACHMENT DEVICE TYPE INDICATES THE TYPE OF DEVICE USED FOR FASTENING AND/OR POSITIONING THE ITEM.PLEASE USE MRC BYGL IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB59 ABYBA 12QUANTITY,DEVICE,ATTACHMENT ATTACHMENT DEVICE QUANTITY THE NUMBER OF ATTACHMENT DEVICES PROVIDED. 1A MODE REPLY 0 ABYCD 02DESIGN,END,SHAFT SHAFT END DESIGN THE DESIGN OF THE SHAFT END. SELECT REPLY CODE 10AB60 ABYDD 19CONFIGURATION,END,SHAFT SHAFT END CONFIGURATION THE GEOMETRIC CONFIGURATION OF THE SHAFT ENDS. SELECT REPLY CODE 10AD07 ABYEJ 10POWER RATING,MOTOR,ELECTRIC ELECTRIC MOTOR POWER RATING THE RATED POWER OF THE ELECTRIC MOTOR. 1D AND 1B MODE REPLY11AC33 ABYFJ /D/ 04DIAMETER,OUTSIDE,CONDUIT CONDUIT OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ABYGD /D/ 19CONFIGURATION,END END CONFIGURATION THE GEOMETRIC CONFIGURATION OF THE ENDS WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AB61 ABYHD /D/ 09MATERIAL,SHIELD SHIELD MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHIELD IS FABRICATED. SELECT REPLY CODE 10AD09 ABYJJ 04DIAMETER,TOP TOP DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TOP,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ABYKJ /D/ 04RADIUS,END,FIRST FIRST END RADIUS NONE. 1D AND 1B MODE REPLY11AA05 ABYLJ /D/ 04LENGTH,SIDE SIDE LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ABYMJ /D/ 04RADIUS,SIDE,FIRST FIRST SIDE RADIUS NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 1D AND 1B MODE REPLY11AA05 ABYNJ /D/ 04RADIUS,END,SECOND SECOND END RADIUS NONE. 1D AND 1B MODE REPLY11AA05 ABYPJ /D/ 04RADIUS,CORNER,FIRST FIRST CORNER RADIUS NONE. 1D AND 1B MODE REPLY11AA05 ABYQJ /D/ 04DIAMETER,HOLE,TOP TOP HOLE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ABYRJ /D/ 04DIAMETER,INSIDE,BASE BASE INSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ABYSJ /D/ 04THICKNESS,TOP TOP THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 ABYTJ /D/ 04DEPTH,SHOULDER SHOULDER DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ABYUJ /D/ 04DIAMETER,OUTSIDE,SHOULDER SHOULDER OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ABYVJ /D/ 04DEPTH,CHAMFER CHAMFER DEPTH NONE. REPLACED BY MRC AGHG WITH ISAC 0368. 1D AND 1B MODE REPLY11AA05 ABYWJ /D/ 04DIAMETER,BOWL BOWL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ABYXJ /D/ 04THICKNESS,FLANGE FLANGE THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 ABYYJ 04DIAMETER,CIRCLE,MOUNTING BOLT MOUNTING BOLT CIRCLE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ABYZB 04ANGLE IN DEG,GROOVE GROOVE ANGLE IN DEG NONE. 1B MODE REPLY 0 ABZAJ /D/ 04DEPTH,GROOVE GROOVE DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ABZBJ /D/ 04DIAMETER,GROOVE,MAJOR MAJOR GROOVE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ABZCJ /D/ 04DIAMETER,GROOVE,MINOR MINOR GROOVE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ABZDJ /D/ 04SPACING,HOLE,MOUNTING,FIRST FIRST MOUNTING HOLE SPACING NONE. 1D AND 1B MODE REPLY11AA05 ABZEJ /D/ 04SPACING,HOLE,MOUNTING,SECOND SECOND MOUNTING HOLE SPACING NONE. 1D AND 1B MODE REPLY11AA05 ABZFJ /D/ 04SPACING,HOLE,MOUNTING,THIRD THIRD MOUNTING HOLE SPACING NONE. 1D AND 1B MODE REPLY11AA05 ABZGJ /D/ 04SPACING,HOLE,MOUNTING,FOURTH FOURTH MOUNTING HOLE SPACING NONE. 1D AND 1B MODE REPLY11AA05 ABZHJ /D/ 04SPACING,HOLE,MOUNTING,FIFTH FIFTH MOUNTING HOLE SPACING NONE. 1D AND 1B MODE REPLY11AA05 ABZJJ /D/ 04SPACING,HOLE,MOUNTING,SIXTH SIXTH MOUNTING HOLE SPACING NONE. 1D AND 1B MODE REPLY11AA05 ABZKJ /D/ 04SPACING,HOLE,MOUNTING,SEVENTH SEVENTH MOUNTING HOLE SPACING NONE. 1D AND 1B MODE REPLY11AA05 ABZLJ /D/ 04DISTANCE BETWEEN DOME HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN DOME HOLES NONE. 1D AND 1B MODE REPLY11AA05 ABZMJ /D/ 04DISTANCE FROM CENTER OF DOME HOLE TO DESIGNATED POINT DISTANCE FROM CENTER OF DOME HOLE TO DESIGNATED POINT NONE. 1D AND 1B MODE REPLY11AA05 ABZNJ /D/ 04WIDTH,NOTCH,SHOULDER SHOULDER NOTCH WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ABZPB 04ANGLE IN DEG,FLAT,SHOULDER SHOULDER FLAT ANGLE IN DEG NONE. 1B MODE REPLY 0 ABZQJ /D/ 04LENGTH,HOLE,CENTER CENTER HOLE LENGTH NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 1D AND 1B MODE REPLY11AA05 ABZRJ /D/ 04WIDTH,HOLE,CENTER CENTER HOLE WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ABZSJ /D/ 04DEPTH,COUNTERBORE,FIRST FIRST COUNTERBORE DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ABZTJ /D/ 04DIAMETER,COUNTERBORE,FIRST FIRST COUNTERBORE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ABZUJ /D/ 04WIDTH,CLAMP,MOUNTING MOUNTING CLAMP WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ABZVJ /D/ 04LENGTH,FLAT,CLAMP,MOUNTING MOUNTING CLAMP FLAT LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ABZWJ /D/ 04LENGTH,TONGUE,CLAMP,MOUNTING MOUNTING CLAMP TONGUE LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ABZXJ /D/ 04HEIGHT,STEP,CLAMP,MOUNTING MOUNTING CLAMP STEP HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 ABZYJ /D/ 13THREAD DIAMETER,STUD,CENTER CENTER STUD THREAD DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ABZZA /D/ 13THREADS PER INCH,STUD,CENTER CENTER STUD THREADS PER INCH NONE. 1A MODE REPLY 0 ACAAD /D/ 13THREAD SERIES,STUD,CENTER CENTER STUD THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A THREADED CENTER STUD. SELECT REPLY CODE 10AC21 ACABA /D/ 13THREAD CLASS,STUD,CENTER CENTER STUD THREAD CLASS NONE. 1A MODE REPLY 0 ACACJ /D/ 13THREAD LENGTH,STUD,CENTER CENTER STUD THREAD LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACADJ /D/ 04LENGTH,STUD,CENTER CENTER STUD LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACAEJ /D/ 04DIAMETER,HOLE,STUD,CENTER CENTER STUD HOLE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACAFJ /D/ 04DEPTH,HOLE,STUD,CENTER CENTER STUD HOLE DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ACAGJ 04DIAMETER,HOLE,TERMINAL WIRE TERMINAL WIRE HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A TERMINAL WIRE ROPE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ACAHJ /D/ 04DEPTH,HOLE,WIRE,TERMINAL TERMINAL WIRE HOLE DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ACAJJ /D/ 04DIAMETER,SHIELD SHIELD DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACAKJ /D/ 04HEIGHT,SHIELD SHIELD HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 ACALJ /D/ 04LENGTH,SLOT,RELIEF,FIRST FIRST RELIEF SLOT LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACAMJ /D/ 04DEPTH,SLOT,RELIEF,FIRST FIRST RELIEF SLOT DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ACANJ /D/ 04THICKNESS,GASKET GASKET THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 ACAPJ /D/ 04HEIGHT ABOVE MOUNTING SURFACE HEIGHT ABOVE MOUNTING SURFACE NONE. 1D AND 1B MODE REPLY11AA05 ACAQA /D/ 13THREAD CLASS,MOUNTING MOUNTING THREAD CLASS NONE. 1A MODE REPLY 0 ACARJ /D/ 13THREAD ENGAGEMENT LENGTH,MOUNTING MOUNTING THREAD ENGAGEMENT LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACASJ /D/ 04DISTANCE FROM FLANGE TO EDGE OF WIRE GROOVE DISTANCE FROM FLANGE TO EDGE OF WIRE GROOVE NONE. 1D AND 1B MODE REPLY11AA05 ACATJ /D/ 04WIDTH ACROSS CORNERS WIDTH ACROSS CORNERS NONE. 1D AND 1B MODE REPLY11AA05 ACAUJ /D/ 04DIAMETER,MAJOR,COUNTERSINK COUNTERSINK MAJOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACAVJ 13THREAD DIAMETER,SHANK SHANK THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A THREADED SHANK,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ACAWA /D/ 13THREADS PER INCH,SHANK SHANK THREADS PER INCH NONE. 1A MODE REPLY 0 ACAXD /D/ 13THREAD SERIES,SHANK SHANK THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A THREADED SHANK. SELECT REPLY CODE 10AC21 ACAYA /D/ 13THREAD CLASS,SHANK SHANK THREAD CLASS NONE. 1A MODE REPLY 0 ACAZJ /D/ 04DEPTH,COUNTERBORE,SECOND SECOND COUNTERBORE DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ACBAJ /D/ 04DIAMETER,COUNTERBORE,SECOND SECOND COUNTERBORE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACBBJ /D/ 13THREAD DIAMETER,COUNTERBORE,FIRST FIRST COUNTERBORE THREAD DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACBCA /D/ 13THREADS PER INCH,COUNTERBORE,FIRST FIRST COUNTERBORE THREADS PER INCH NONE. 1A MODE REPLY 0 ACBDD /D/ 13THREAD SERIES,COUNTERBORE,FIRST FIRST COUNTERBORE THREAD SERIES A DESINGATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A THREADED FIRST COUNTERBORE. SELECT REPLY CODE 10AC21 ACBEA /D/ 13THREAD CLASS,COUNTERBORE,FIRST FIRST COUNTERBORE THREAD CLASS NONE. 1A MODE REPLY 0 ACBFJ /D/ 13THREAD DIAMETER,COUNTERBORE,SECOND SECOND COUNTERBORE THREAD DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACBGA /D/ 13THREADS PER INCH,COUNTERBORE,SECOND SECOND COUNTERBORE THREADS PER INCH NONE. 1A MODE REPLY 0 ACBHD /D/ 13THREAD SERIES,COUNTERBORE,SECOND SECOND COUNTERBORE THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A THREADED SECOND COUNTERBORE. SELECT REPLY CODE 10AC21 ACBJA /D/ 13THREAD CLASS,COUNTERBORE,SECOND SECOND COUNTERBORE THREAD CLASS NONE. 1A MODE REPLY 0 ACBKJ /D/ 04WIDTH,SLOT,RELIEF,FIRST FIRST RELIEF SLOT WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ACBLJ /D/ 04LENGTH,SLOT,RELIEF,SECOND SECOND RELIEF SLOT LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACBMJ /D/ 04WIDTH,SLOT,RELIEF,SECOND SECOND RELIEF SLOT WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ACBNJ /D/ 04DEPTH,SLOT,RELIEF,SECOND SECOND RELIEF SLOT DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ACBPJ /D/ 04WIDTH,SLOT,FIRST FIRST SLOT WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ACBQJ /D/ 04DEPTH,SLOT,FIRST FIRST SLOT DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ACBRJ /D/ 04LENGTH,SHOULDER SHOULDER LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACBSJ /D/ 04LENGTH,PORTION,FLATTED FLATTED PORTION LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACBTJ /D/ 04DIAMETER,OUTSIDE,SHANK SHANK OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACBUJ /D/ 04THICKNESS,WALL WALL THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 ACBVJ /D/ 04HEIGHT,SHANK SHANK HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 ACBWJ 04LENGTH,SHANK SHANK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SHANK,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 ACBXJ /D/ 04WIDTH,SHANK SHANK WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ACBYJ /D/ 04WIDTH,KEY,FIRST FIRST KEY WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ACBZJ /D/ 04THICKNESS,KEY,FIRST FIRST KEY THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 ACCAJ /D/ 04DEPTH,KEY,FIRST FIRST KEY DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ACCBJ /D/ 04WIDTH,KEY,SECOND SECOND KEY WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ACCCJ /D/ 04THICKNESS,KEY,SECOND SECOND KEY THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 ACCDJ /D/ 04DEPTH,KEY,SECOND SECOND KEY DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ACCEJ /D/ 04DIAMETER,HOLE,FIRST FIRST HOLE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACCFJ /D/ 04DIAMETER,HOLE,SECOND SECOND HOLE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACCGJ /D/ 04SPACING,HOLE,FIRST FIRST HOLE SPACING NONE. 1D AND 1B MODE REPLY11AA05 ACCHJ /D/ 04SPACING,HOLE,SECOND SECOND HOLE SPACING NONE. 1D AND 1B MODE REPLY11AA05 ACCJJ /D/ 04DISTANCE FROM OUTSIDE FLATTED PORTION TO OPPOSITE SURFACE DISTANCE FROM OUTSIDE FLATTED PORTION TO OPPOSITE SURFACE NONE. 1D AND 1B MODE REPLY11AA05 ACCKJ /D/ 04DISTANCE FROM INSIDE FLATTED PORTION TO OPPOSITE SURFACE DISTANCE FROM INSIDE FLATTED PORTION TO OPPOSITE SURFACE NONE. 1D AND 1B MODE REPLY11AA05 ACCLJ /D/ 04DIAMETER,STEP,FIRST FIRST STEP DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACCMJ /D/ 04HEIGHT,STEP,FIRST FIRST STEP HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 ACCNJ /D/ 04DIAMETER,STEP,SECOND SECOND STEP DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACCPJ /D/ 04HEIGHT,STEP,SECOND SECOND STEP HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 ACCQJ /D/ 04DISTANCE FROM CENTERLINE TO FLAT DISTANCE FROM CENTERLINE TO FLAT NONE. 1D AND 1B MODE REPLY11AA05 ACCRJ /D/ 04RADIUS,CORNER,SECOND SECOND CORNER RADIUS NONE. 1D AND 1B MODE REPLY11AA05 ACCSJ /D/ 04DISTANCE FROM CONDUCTOR SLOT TO OPPOSITE SURFACE,FIRST FIRST DISTANCE FROM CONDUCTOR SLOT TO OPPOSITE SURFACE NONE. 1D AND 1B MODE REPLY11AA05 ACCTA 19MODEL NUMBER FOR WHICH DESIGNED,AUGER AUGER MODEL NUMBER FOR WHICH DESIGNED THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE AUGER FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 ACCUJ /D/ 04DISTANCE FROM CONDUCTOR SLOT TO OPPOSITE SURFACE,SECOND SECOND DISTANCE FROM CONDUCTOR SLOT TO OPPOSITE SURFACE NONE. 1D AND 1B MODE REPLY11AA05 ACCVJ /D/ 04DISTANCE BETWEEN CONDUCTOR GROOVE AND MOUNTING HOLE DISTANCE BETWEEN CONDUCTOR GROOVE AND MOUNTING HOLE NONE. 1D AND 1B MODE REPLY11AA05 ACCWJ /D/ 04DISTANCE BETWEEN CONDUCTOR GROOVES,FIRST FIRST DISTANCE BETWEEN CONDUCTOR GROOVES NONE. 1D AND 1B MODE REPLY11AA05 ACCXJ /D/ 04DISTANCE BETWEEN CONDUCTOR GROOVES,SECOND SECOND DISTANCE BETWEEN CONDUCTOR GROOVES NONE. 1D AND 1B MODE REPLY11AA05 ACCYJ /D/ 04DISTANCE,SEPARATION,CONDUCTOR CONDUCTOR SEPARATION DISTANCE NONE. 1D AND 1B MODE REPLY11AA05 ACCZJ /D/ 04DISTANCE FROM CONDUCTOR GROOVE TO END OF INSULATOR,FIRST FIRST DISTANCE FROM CONDUCTOR GROOVE TO END OF INSULATOR NONE. 1D AND 1B MODE REPLY11AA05 ACDAJ /D/ 04DIAMETER,HOLE,THIRD THIRD HOLE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACDBJ /D/ 04DIAMETER,HOLE,FOURTH FOURTH HOLE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACDCD 18TYPE,CURRENT CURRENT TYPE INDICATES THE TYPE OF CURRENT WHETHER ALTERNATING,DIRECT,OR BOTH. SELECT REPLY CODE 10AB62 ACDDJ /D/ 04SPACING,HOLE,THIRD THIRD HOLE SPACING NONE. 1D AND 1B MODE REPLY11AA05 ACDEJ /D/ 04SPACING,HOLE,FOURTH FOURTH HOLE SPACING NONE. 1D AND 1B MODE REPLY11AA05 ACDFJ /D/ 04SPACING,HOLE,FIFTH FIFTH HOLE SPACING NONE. 1D AND 1B MODE REPLY11AA05 ACDGJ /D/ 04SPACING,HOLE,SIXTH SIXTH HOLE SPACING NONE. 1D AND 1B MODE REPLY11AA05 ACDHJ /D/ 04SPACING,HOLE,SEVENTH SEVENTH HOLE SPACING NONE. 1D AND 1B MODE REPLY11AA05 ACDJJ /D/ 04SPACING,HOLE,EIGHTH EIGHTH HOLE SPACING NONE. 1D AND 1B MODE REPLY11AA05 ACDKB 04SPACING IN DEG,ANGULAR,FIRST FIRST ANGULAR SPACING IN DEG NONE. 1B MODE REPLY 0 ACDLB 04SPACING IN DEG,ANGULAR,SECOND SECOND ANGULAR SPACING IN DEG NONE. 1B MODE REPLY 0 ACDMB 04SPACING IN DEG,ANGULAR,THIRD THIRD ANGULAR SPACING IN DEG NONE. 1B MODE REPLY 0 ACDNJ 04DIAMETER,BOTTOM BOTTOM DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOTTOM OF THE ITEM,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ACDPJ /D/ 04DISTANCE FROM CENTERLINE OF HOLE TO END OF STUD DISTANCE FROM CENTERLINE OF HOLE TO END OF STUD NONE. 1D AND 1B MODE REPLY11AA05 ACDQJ /D/ 04DIAMETER,MAJOR,TURRET TURRET MAJOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACDRJ /D/ 04THICKNESS,TURRET TURRET THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 ACDSA /D/ 13THREAD CLASS,TERMINATION TERMINATION THREAD CLASS NONE. 1A MODE REPLY 0 ACDTJ /D/ 13THREAD DEPTH,INTERNAL,TERMINATION TERMINATION INTERNAL THREAD DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ACDUJ /D/ 04DIAMETER,NOMINAL,HOLE,PIN PIN HOLE NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACDVJ /D/ 04DEPTH,HOLE,PIN PIN HOLE DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ACDWJ /D/ 04RADIUS,GROOVE,WIRE,TOP TOP WIRE GROOVE RADIUS NONE. 1D AND 1B MODE REPLY11AA05 ACDXJ /D/ 04RADIUS,GROOVE,RADIAL RADIAL GROOVE RADIUS NONE. 1D AND 1B MODE REPLY11AA05 ACDYJ /D/ 04DIAMETER,GROOVE,RADIAL RADIAL GROOVE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACDZJ /D/ 04LENGTH,SKIRT SKIRT LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACEAJ /D/ 04WIDTH,GROOVE,RADIAL,FIRST FIRST RADIAL GROOVE WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ACEBJ /D/ 04WIDTH,GROOVE,RADIAL,SECOND SECOND RADIAL GROOVE WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ACECJ /D/ 13THREAD DIAMETER,TERMINATION TERMINATION THREAD DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACEDA 13THREADS PER INCH,TERMINATION TERMINATION THREADS PER INCH THE NUMBER OF THREADS PER INCH OF A THREADED TERMINATION. 1A MODE REPLY 0 ACEEJ /D/ 04SPACING,HOLE,NINTH NINTH HOLE SPACING NONE. 1D AND 1B MODE REPLY11AA05 ACEFD /D/ 13THREAD SERIES,TERMINATION TERMINATION THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A THREADED TERMINATION. SELECT REPLY CODE 10AC21 ACEGJ /D/ 04SPACING,HOLE,TENTH TENTH HOLE SPACING NONE. 1D AND 1B MODE REPLY11AA05 ACEHJ /D/ 04LENGTH,CUT,CORNER CORNER CUT LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACEJJ /D/ 04WIDTH,CUT,CORNER CORNER CUT WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ACEKJ /D/ 04DISTANCE,CENTER,FIRST FIRST CENTER DISTANCE NONE. 1D AND 1B MODE REPLY11AA05 ACELJ /D/ 04DISTANCE,CENTER,SECOND SECOND CENTER DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 ACEMJ /D/ 04WIDTH,LEG,FIRST FIRST LEG WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ACENJ /D/ 04WIDTH,LEG,SECOND SECOND LEG WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ACEPJ /D/ 04DISTANCE BETWEEN LEGS DISTANCE BETWEEN LEGS NONE. 1D AND 1B MODE REPLY11AA05 ACEQJ /D/ 04WIDTH,HOLE,FIRST FIRST HOLE WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ACERJ /D/ 04LENGTH,HOLE,FIRST FIRST HOLE LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACESJ /D/ 04WIDTH,HOLE,SECOND SECOND HOLE WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ACETJ /D/ 04LENGTH,HOLE,SECOND SECOND HOLE LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACEUJ /D/ 04RADIUS,SIDE,SECOND SECOND SIDE RADIUS NONE. 1D AND 1B MODE REPLY11AA05 ACEVB 04ANGLE IN DEG,PLATE PLATE ANGLE IN DEG NONE. 1B MODE REPLY 0 ACEWJ /D/ 04THICKNESS,WASHER WASHER THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 ACEXJ /D/ 04LENGTH,STEP,FIRST FIRST STEP LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACEYJ /D/ 04LENGTH,STEP,SECOND SECOND STEP LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACEZJ /D/ 04HEIGHT,STEP,THIRD THIRD STEP HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 ACFAJ /D/ 04WIDTH,SLOT,SECOND SECOND SLOT WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ACFBJ /D/ 04DEPTH,SLOT,SECOND SECOND SLOT DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ACFCJ /D/ 04DISTANCE FROM CONDUCTOR HOLE TO END OF INSULATOR,FIRST FIRST DISTANCE FROM CONDUCTOR HOLE TO END OF INSULATOR NONE. 1D AND 1B MODE REPLY11AA05 ACFDJ /D/ 04DISTANCE FROM CONDUCTOR HOLE TO END OF INSULATOR,SECOND SECOND DISTANCE FROM CONDUCTOR HOLE TO END OF INSULATOR NONE. 1D AND 1B MODE REPLY11AA05 ACFEJ /D/ 04DIAMETER,BOLT,LAG LAG BOLT DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACFFJ /D/ 04DEPTH,BOWL BOWL DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ACFGJ /D/ 04THICKNESS,FLANGE,INSERT INSERT FLANGE THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 ACFHJ /D/ 04DEPTH,HOLE,FEATURE,NONTURN NONTURN FEATURE HOLE DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ACFJJ /D/ 04DIAMETER,HOLE,WIRE,SECOND SECOND WIRE HOLE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACFKJ /D/ 04HEIGHT,CAP,FIRST FIRST CAP HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 ACFLJ /D/ 04HEIGHT,CAP,SECOND SECOND CAP HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 ACFMJ /D/ 13THREAD DIAMETER,CAP CAP THREAD DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACFNA /D/ 13THREADS PER INCH,CAP CAP THREADS PER INCH NONE. 1A MODE REPLY 0 ACFPD /D/ 13THREAD SERIES,CAP CAP THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A THREADED CAP. SELECT REPLY CODE 10AC21 ACFQA /D/ 13THREAD CLASS,CAP CAP THREAD CLASS NONE. 1A MODE REPLY 0 ACFRJ /D/ 13THREAD DEPTH,INTERNAL,CAP CAP INTERNAL THREAD DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ACFSJ /D/ 13THREAD DIAMETER,BASE BASE THREAD DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACFTA /D/ 13THREADS PER INCH,BASE BASE THREADS PER INCH NONE. 1A MODE REPLY 0 ACFUD /D/ 13THREAD SERIES,BASE BASE THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A THREADED BASE. SELECT REPLY CODE 10AC21 ACFVA /D/ 13THREAD CLASS,BASE BASE THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREADED BASE. 1A MODE REPLY 0 ACFWJ /D/ 13THREAD DEPTH,INTERNAL,BASE BASE INTERNAL THREAD DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ACFXJ /D/ 04HEIGHT,BASE BASE HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 ACFYJ /D/ 04DEPTH,HOLE,TOP TOP HOLE DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ACFZJ /D/ 04LENGTH,SHACKLE SHACKLE LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACGAJ /D/ 04LENGTH,HOLE,WIRE WIRE HOLE LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACGBJ /D/ 04THICKNESS,TONGUE,FIRST FIRST TONGUE THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 ACGCJ 04DIAMETER,ACCOMMODATED,WIRE ROPE WIRE ROPE ACCOMMODATED DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR WHICH THE WIRE ROPE IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ACGDJ /D/ 04LENGTH,TONGUE,FIRST FIRST TONGUE LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACGEJ /D/ 04LENGTH,TONGUE,SECOND SECOND TONGUE LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACGFJ /D/ 04THICKNESS,TONGUE,SECOND SECOND TONGUE THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 ACGGJ /D/ 04DIAMETER,MAJOR,HOLE,TAPERED TAPERED HOLE MAJOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACGHJ /D/ 04DEPTH,HOLE,TAPERED TAPERED HOLE DEPTH NONE. 1D AND 1B MODE REPLY11AA05 ACGJJ /D/ 04WIDTH,SHACKLE SHACKLE WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ACGKJ /D/ 04THICKNESS,SHACKLE SHACKLE THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 ACGLJ /D/ 04DISTANCE FROM INSIDE OF MOUNTING HOLE TO OUTSIDE SURFACE DISTANCE FROM INSIDE OF MOUNTING HOLE TO OUTSIDE SURFACE NONE. 2D AND 1B MODE REPLY21AA051AC20 ACGMJ /D/ 04DIAMETER,PIN,CLEVIS CLEVIS PIN DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACGNJ /D/A10VOLTAGE RATING,FLASHOVER,DRY DRY FLASHOVER VOLTAGE RATING THE ELECTRICAL POTENTIAL IN VOLTS,MULTIPLES OR SUBMULTIPLES OF VOLTS,WHICH WILL CAUSE A DISRUPTIVE DISCHARGE OVER A DRY INSULATOR. 1D AND 1A MODE REPLY11AB63 ACGPJ /D/A10VOLTAGE RATING,FLASHOVER,WET WET FLASHOVER VOLTAGE RATING THE ELECTRICAL POTENTIAL IN VOLTS,MULTIPLES OR SUBMULTIPLES OF VOLTS,WHICH WILL CAUSE A DISRUPTIVE DISCHARGE OVER A WET INSULATOR. 1D AND 1A MODE REPLY11AB63 ACGQJ /D/A10STRENGTH,CANTILEVER CANTILEVER STRENGTH THE MAXIMUM BENDING LOAD AN ITEM CAN WITHSTAND WITHOUT BREAKING. 1D AND 1A MODE REPLY12AB16 ACGRJ 10STRENGTH,COMPRESSION COMPRESSION STRENGTH THE MAXIMUM SQUEEZING LOAD AN ITEM CAN WITHSTAND WITHOUT BREAKING. 1D AND 1B MODE REPLY12AB16 ACGSJ /D/ 10STRENGTH,TORSIONAL TORSIONAL STRENGTH THE MAXIMUM TWISTING STRESS AN ITEM CAN WITHSTAND WITHOUT BREAKING. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 1D AND 1B MODE REPLY12AB16 ACGTJ /D/ 10STRENGTH,TRANSVERSE TRANSVERSE STRENGTH THE MAXIMUM LATERAL STRESS AN ITEM CAN WITHSTAND WITHOUT BREAKING. 1D AND 1B MODE REPLY12AB16 ACGUJ /D/ 10STRENGTH,MECHANICAL AND ELECTRICAL,COMBINED COMBINED MECHANICAL AND ELECTRICAL STRENGTH THE LOAD AT WHICH ANY PART OF THE ITEM FAILS TO PERFORM ITS FUNCTION, EITHER ELECTRICALLY OR MECHANICALLY, WHEN VOLTAGE AND MECHANICAL STRESS ARE APPLIED SIMULTANEOUSLY. 1D AND 1B MODE REPLY12AB16 ACGVB /D/ 10RATING AT 1 MEGAHERTZ IN MICROVOLTS,VOLTAGE,INFLUENCE,RADIO RADIO INFLUENCE VOLTAGE RATING AT 1 MEGAHERTZ IN MICROVOLTS THE AMOUNT OF GENERATED RADIO NOISE VOLTAGE MEASURED AT A SPECIFIED FREQUENCY. 1B MODE REPLY 0 ACGWD /D/ 19PROCESS,MANUFACTURING,MATERIAL,INSULATOR INSULATOR MATERIAL MANUFACTURING PROCESS THE OPERATION USED TO PRODUCE THE INSULATING MATERIAL. SELECT REPLY CODE 10AD57 ACGXD /D/ 17SURFACE THREATMENT,CERAMIC,EXTERIOR EXTERIOR CERAMIC SURFACE THREATMENT A HARD, SMOOTH, HIGH GLOSS SILICATE GLASS EXTERIOR SURFACE COATING, OR LACK OF COATING, ON THE CERAMIC INSULATOR. SELECT REPLY CODE 10AD09 ACGYB 10VOLTAGE RATING PER MIL THICKNESS IN VOLTS,DIELECTRIC MATERIAL DIELECTRIC MATERIAL VOLTAGE RATING PER MIL THICKNESS IN VOLTS THE MAXIMUM POTENTIAL GRADIENT THAT THE INSULATING MATERIAL CAN WITHSTAND PER MIL /0.001 INCH/ THICKNESS WITHOUT RUPTURE. 1B MODE REPLY 0 ACGZJ /D/ 10HARDNESS RATING,NONMETALLIC NONMETALLIC HARDNESS RATING A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF A NONMETALLIC ITEM WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE. 1D AND 1B MODE REPLY12AC26 ACHAJ /D/ 10VOLTAGE,CORONA CORONA VOLTAGE THE CRITICAL VOLTAGE IN VOLTS, MULTIPLES OR SUBMULTIPLES OF VOLTS, THAT STARTS THE LUMINOUS DISCHARGE DUE TO IONIZATION OF THE SURROUNDING AIR AND IS THE START OF DETERIORATION OF THE MATERIAL. 1D AND 1B MODE REPLY11AB63 ACHBD /D/ 09MATERIAL,BASE,MOUNTING MOUNTING BASE MATERIAL THE COMPOSITION FROM WHICH THE MOUNTING BASE IS FABRICATED. SELECT REPLY CODE 10AD09 ACHCD /D/ 17SURFACE TREATMENT,BASE,MOUNTING MOUNTING BASE SURFACE TREATMENT THE COATING, DIP, OR PLATING APPLIED TO THE MOUNTING BASE SURFACE FOR ENVIRONMENTAL PROTECTION OR TO INCREASE FUNCTIONAL EFFICIENCY. SELECT REPLY CODE 10AD09 ACHDA /D/ 12QUANTITY,CONDUCTYOR,MECHANICAL ACCOMMODATION MECHANICAL ACCOMMODATION CONDUCTYOR QUANTITY THE NUMBER OF CONDUCTORS THE ITEM ACCOMMODATES FOR THE PURPOSE OF SPACING AND/OR SUPPORTING THE CONDUCTOR(S).EXCLUDES ELECTRICAL TERMINATIONS WHICH PROVIDE ELECTRICAL CONNECTION AND TERMINAL LUGS. 1A MODE REPLY 0 ACHEJ 04DIAMETER,AUGER AUGER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN AUGER, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACHFA 12QUANTITY,TERMINATION,ELECTRICAL ELECTRICAL TERMINATION QUANTITY THE NUMBER OF TERMINATIONS WHICH FACILITATE ELECTRICAL CONNECTION,SUCH AS TERMINAL LUG/S/,STUD/S/,CAP/S/,AND THE LIKE. EXCLUDES SPACERS OR SUPPORTS. 1A MODE REPLY 0 ACHGD /D/ 09MATERIAL,TERMINATION,ELECTRICAL ELECTRICAL TERMINATION MATERIAL THE COMPOSITION OF THE METALLIC TERMINAL LUG(S), STUD(S), INSERT(S), CAP(S), OR THE LIKE, WHICH FACILITATES ELECTRICAL CONNECTION. SELECT REPLY CODE 10AD09 ACHHD /D/ 17SURFACE TREATMENT,TERMINATION,ELECTRICAL ELECTRICAL TERMINATION SURFACE TREATMENT THE COATING,DIP,OR PLATING APPLIED TO THE ELECTRICAL TERMINATION FOR ENVIRONMENTAL PROTECTION OR TO INCREASE FUNCTIONAL EFFICIENCY. SELECT REPLY CODE 10AD09 ACHJD /D/ 09MATERIAL,GASKET,MOUNTING MOUNTING GASKET MATERIAL THE COMPOSITION FROM WHICH THE MOUNTING GASKET IS MANUFACTURED. SELECT REPLY CODE 10AD09 ACHKA /D/ 12QUANTITY,NUT NUT QUANTITY THE NUMBER OF NUTS FURNISHED FOR MOUNTING AND/OR CONDUCTOR ATTACHING PURPOSES. 1A MODE REPLY 0 ACHLA /D/ 12QUANTITY,WASHER,FLAT FLAT WASHER QUANTITY THE NUMBER OF NONLOCKING TYPE WASHERS FOR MOUNTING AND/OR CONDUCTOR ATTACHING PURPOSES. 1A MODE REPLY 0 ACHMA /D/ 12QUANTITY,WASHER,LOCK LOCK WASHER QUANTITY THE NUMBER OF LOCK WASHERS FURNISHED. 1A MODE REPLY 0 ACHNA /D/ 12QUANTITY,LUG,TERMINAL TERMINAL LUG QUANTITY THE NUMBER OF TERMINAL LUGS FURNISHED. 1A MODE REPLY 0 ACHPG 19HARDWARE,FURNISHED FURNISHED HARDWARE HARDWARE FURNISHED WITH THE ITEM. FULL TEXT WRITE-IN 0 ACHQD /D/ 19FEATURE,LOCK LOCK FEATURE THE DESIGN FEATURE WHICH INCORPORATES A LOCKING FEATURE BY USE OF A PULL RING OR OTHER MEANS TO LOCK THE PLUNGER OPEN PERMITTING DETENTS TO REMAIN IN RETRACTED POSITION. SELECT REPLY CODE 10AB65 ACHRD /D/ 18TYPE,ATTACHMENT ATTACHMENT TYPE THOSE COMPONENTS ATTACHED TO THE ITEM TO KEEP IT EASILY ACCESSIBLE FOR USE WHEN IT IS REMOVED FROM ITS APPLIED POSITION. SELECT REPLY CODE 10AB66 ACHSJ 04LENGTH,LANYARD LANYARD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A LANYARD. 2D AND 1B MODE REPLY21AA051AC20 ACHTJ 04LENGTH,OVERALL,PIN PIN OVERALL LENGTH THE OVERALL DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS,WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE PIN. 2D AND 1B MODE REPLY21AA051AC20 ACHUJ 04DIAMETER,OVERALL,PIN PIN OVERALL DIAMETER THE OVERALL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PIN,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACHVD 03DESIGNATION,SIZE,PIN PIN SIZE DESIGNATION A STANDARD OR MEASUREMENT,EXPRESSED AS A NUMERIC VALUE,FOR DESIGNATING THE SIZE OF THE PIN. SELECT REPLY CODE 10AB31 ACHWA 03DESIGNATION OF STEP ECCENTRIC TO HEAD,NUMERIC NUMERIC DESIGNATION OF STEP ECCENTRIC TO HEAD THE NUMBER THAT DESIGNATES THE ENLARGED PORTION OF THE SHANK WHOSE CENTERLINE IS NOT COLLINEAR WITH THE CENTERLINE OF THE HEAD OF AN ITEM. 1A MODE REPLY 0 ACHXD /D/ 09MATERIAL FOR WHICH DESIGNED MATERIAL FOR WHICH DESIGNED THE MATERIAL FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AD09 ACHYD 18TYPE,HOLE,MOUNTING MOUNTING HOLE TYPE INDICATES THE TYPE OF HOLES PROVIDED IN THE ITEM TO FACILITATE MOUNTING TO ANOTHER ITEM. SELECT REPLY CODE 10AB68 ACHZJ 04DIAMETER,HOLE,PIN MOUNTING PIN MOUNTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PIN MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACJAJ /D/A13THREAD SIZE,HOLE,MOUNTING MOUNTING HOLE THREAD SIZE THE THREAD SERIES,THREAD MAJOR/MAXIMUM DIAMETER,AND THE NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AC21 ACJBA 13THREAD CLASS,HOLE,MOUNTING MOUNTING HOLE THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREADED MOUNTING HOLE. 1A MODE REPLY 0 ACJCD /D/ 13THREAD DIRECTION,HOLE,MOUNTING MOUNTING HOLE THREAD DIRECTION THE DIRECTION OF THE MOUNTING HOLE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ACJDJ 04DEPTH,HOLE,MOUNTING MOUNTING HOLE DEPTH A MEASUREMENT FROM THE BOTTOM OF THE MOUNTING HOLE TO THE SURFACE OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ACJED /D/ 18TYPE,EDGE EDGE TYPE INDICATES THE TYPE OF EDGE CONFIGURATION OF THE ITEM. SELECT REPLY CODE 10AB69 ACJFJ 04LENGTH,CHAMFER,KEY KEY CHAMFER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BEVELED EDGE OF THE KEY,IN DISTINCTION FROM WIDTH. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 ACJGB /D/ 04ANGLE IN DEG,CHAMFER,KEY KEY CHAMFER ANGLE IN DEG THE ANGLE OF THE BEVELED EDGE OR CORNERS OF THE KEY,EXPRESSED IN DEGREES. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 ACJHJ 04RADIUS,EDGE,STARTING STARTING EDGE RADIUS THE CURVED EDGE DIMENSION OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ACJJD 03DESIGNATION,SIZE,KEY KEY SIZE DESIGNATION A NUMBER OR LETTER REPRESENTING THE SIZE OF A KEY. SELECT REPLY CODE 10AB70 ACJKJ /D/ 08LOCATION,HOLE,MOUNTING MOUNTING HOLE LOCATION INDICATES THE LOCATION OF THE MOUNTING HOLE(S) IN RELATION TO THE DISTANCE FROM THE CENTER OF THE MOUNTING HOLE(S) ALONG A STRAIGHT LINE PARALLEL TO THE LONGITUDINAL AXIS TO THE END(S) OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ACJLB 04ANGLE IN DEG,BEND BEND ANGLE IN DEG THE ANGULAR MEASUREMENT BY WHICH ONE PART/SECTION OF A RIGID ITEM DEVIATES FROM A STRAIGHT LINE PROJECTION OF AN ADJACENT PART/SECTION,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ACJMJ /D/ 04RADIUS,BEND BEND RADIUS NONE. 1D AND 1B MODE REPLY11AA05 ACJNJ 04DISTANCE,OFFSET OFFSET DISTANCE NONE. 1D AND 1B MODE REPLY11AA05 ACJPJ /D/ 04LENGTH,TANGENT TANGENT LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACJQJ 04DIAMETER,INSIDE,NOMINAL NOMINAL INSIDE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO SURFACES OF AN ITEM,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ACJRJ /D/ 04LENGTH,CONDUIT CONDUIT LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACJSJ /D/ 04LENGTH,ASSEMBLY,CONDUIT CONDUIT ASSEMBLY LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACJTJ /D/ 04LENGTH,SECTION,FLEXIBLE OR RIGID FLEXIBLE OR RIGID SECTION LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACJUD /D/ 07PROVISION,COUPLING COUPLING PROVISION INDICATES WHETHER A COUPLING IS OR IS NOT FURNISHED. SELECT REPLY CODE 10AA55 ACJVD /D/ 09MATERIAL,TREATMENT,NONMETALLIC CONDUIT NONMETALLIC CONDUIT TREATMENT MATERIAL THE PENETRATIVE TYPE SOLUTION WITH WHICH THE MATERIAL IS IMPREGNATED. SELECT REPLY CODE 10AD09 ACJWD /D/ 18TYPE,END,CONDUIT TERMINAL CONDUIT TERMINAL END TYPE INDICATES THE TYPE OF TERMINATING PART(S) ATTACHED TO THE ENDS OF THE CONDUIT. SELECT REPLY CODE 10AB71 ACJXB /D/ 04ANGLE IN DEG,END,CONDUIT TERMINAL CONDUIT TERMINAL END ANGLE IN DEG THE ANGLE BETWEEN THE FACE OF THE ATTACHED END AND THE FACE OF THE CONNECTING END,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ACJYB /D/ 04ANGLE IN DEG,TWIST TWIST ANGLE IN DEG THE ANGLE BETWEEN ANGULAR TERMINAL ENDS WHEN USING THE CONDUIT PORTION OF THE ASSEMBLY AS AN AXIS,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ACJZD /D/ 14SHAPE,ACCOMMODATION,GRIPPING,COUPLING NUT COUPLING NUT GRIPPING ACCOMMODATION SHAPE THE PHYSICAL CONFIGURATION OF THE COUPLING NUT USED AS A GRIPPING AID IN THE APPLICATION OF TORQUE. SELECT REPLY CODE 10AD07 ACKAD /D/ 18TYPE,ACCOMMODATION,GRIPPING,COUPLING NUT COUPLING NUT GRIPPING ACCOMMODATION TYPE INDICATES THE TYPE OF COUPLING NUT GRIPPING ACCOMMODATION USED AS AN AID IN THE APPLICATION OF TORQUE. SELECT REPLY CODE 10AB24 ACKBD /D/ 09MATERIAL,END,TERMINAL TERMINAL END MATERIAL THE COMPOSITION FROM WHICH THE TERMINAL END/S/ IS MADE. SELECT REPLY CODE 10AD09 ACKCD /D/ 17SURFACE TREATMENT,END,TERMINAL TERMINAL END SURFACE TREATMENT THE COATING,DIP,OR PLATING APPLIED TO THE TERMINAL END FOR ENVIRONMENTAL PROTECTION OR TO INCREASE FUNCTIONAL EFFICIENCY. SELECT REPLY CODE 10AD09 ACKDD /D/ 09MATERIAL,PACKING,FLEXIBLE JOINT FLEXIBLE JOINT PACKING MATERIAL THE MATERIAL USED FOR PACKING BETWEEN THE FLEXIBLE JOINTS OF THE ITEM. SELECT REPLY CODE 10AD09 ACKED 18TYPE,SHIELD,BRAIDED METALLIC BRAIDED METALLIC SHIELD TYPE INDICATES THE TYPE OF THE MATERIAL,FORM,AND/OR FINISH OF WOVEN METAL BRAID APPLIED OVER THE INNER CORE FOR PROTECTION AND SUPPRESSION OF ELECTRICAL INTERFERENCE. SELECT REPLY CODE 10AB73 ACKFD /D/ 18TYPE PROVIDED,COVERING COVERING TYPE PROVIDED INDICATES THE TYPE OF AN OUTER COVERING OR CHAFING SLEEVE PROVIDED FOR ADDITIONAL MECHANICAL PROTECTION AND RESISTANCE TO FLUIDS AND OTHER CORROSIVE ELEMENTS. SELECT REPLY CODE 10AB74 ACKGD /D/ 09MATERIAL,COVERING COVERING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE COVERING IS FABRICATED. SELECT REPLY CODE 10AD09 ACKHJ 04RADIUS,BENDING,MINIMUM INSIDE MINIMUM INSIDE BENDING RADIUS THE MINIMUM INSIDE BENDING RADIUS FORMED WITHOUT STRESSING OR DEFORMATION OF A FLEXIBLE ITEM. 1D AND 1B MODE REPLY11AA05 ACKJB /D/ 10FINISH IN MICROINCHES,RMS,INSIDE SURFACE INSIDE SURFACE RMS FINISH IN MICROINCHES THE SPECIFIC ROOT MEAN SQUARE FINISH ON THE INSIDE SURFACE OF AN ITEM,EXPRESSED IN MICROINCHES. 1B MODE REPLY 0 ACKKB /D/ 10FINISH IN MICROINCHES,RMS,OUTSIDE SURFACE OUTSIDE SURFACE RMS FINISH IN MICROINCHES THE SPECIFIC ROOT MEAN SQUARE FINISH ON THE OUTSIDE SURFACE OF AN ITEM,EXPRESSED IN MICROINCHES. 1B MODE REPLY 0 ACKLD /D/ 19MEDIA FOR WHICH DESIGNED MEDIA FOR WHICH DESIGNED THE TYPE OF SERVICE WITH WHICH THE ITEM IS DESIGNED TO BE USED. PLEASE USE MRC MEDA IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB75 ACKMD 18TYPE,CONNECTION,FIRST END FIRST END CONNECTION TYPE A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION. SELECT REPLY CODE 10AB76 ACKNL 16STYLE DESIGNATOR,END,FIRST FIRST END STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END. 1L MODE REPLY 0 ACKPJ 04HEIGHT,FACE,RAISED,FIRST END FIRST END RAISED FACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ACKQJ 04DIAMETER,FACE,RAISED,FIRST END FIRST END RAISED FACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACKRJ 04DIAMETER,RECESS,FIRST END FIRST END RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACKSJ 04DEPTH,RECESS,FIRST END FIRST END RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACKTL 16STYLE,SHAPE,FIRST END FLANGE FIRST END FLANGE SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE END FLANGE. 1L MODE REPLY 0 ACKUJ 04THICKNESS,FLANGE,FIRST END FIRST END FLANGE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE FIRST END FLANGE, IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ACKVJ 04LENGTH,FLANGE,FIRST END FIRST END FLANGE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FIRST END FLANGE, IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ACKWJ 04WIDTH,FLANGE,FIRST END FIRST END FLANGE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FIRST END FLANGE, IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ACKXJ 04RADIUS,END,FIRST END FLANGE FIRST END FLANGE END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ACKYJ 04WIDTH ACROSS FLATS,END,FIRST FIRST END WIDTH ACROSS FLATS THE DISTANCE FROM ONE FLAT TO THE OPPOSITE FLAT OF THE FIRST END. 2D AND 1B MODE REPLY21AA051AC20 ACKZA 12QUANTITY,HOLE,BOLT,FIRST END FIRST END BOLT HOLE QUANTITY THE NUMBER OF BOLT HOLES PROVIDED ON THE ITEM. 1A MODE REPLY 0 ACLAJ 04DIAMETER,HOLE,BOLT,FIRST END FIRST END BOLT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACLBJ 04DIAMETER,CIRCLE,BOLT,FIRST END FIRST END BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACLCJ /D/ 04DISTANCE BETWEEN BOLT HOLES ALONG LENGTH,FIRST END FIRST END DISTANCE BETWEEN BOLT HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACLDJ /D/ 04DISTANCE BETWEEN BOLT HOLES ALONG WIDTH,FIRST END FIRST END DISTANCE BETWEEN BOLT HOLES ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACLEJ 04DIAMETER HOSE ACCOMMODATED,INSIDE,FIRST END FIRST END INSIDE DIAMETER HOSE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACLFJ 04DIAMETER HOSE ACCOMMODATED,OUTSIDE,FIRST END FIRST END OUTSIDE DIAMETER HOSE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACLGJ 04SIZE ACCOMMODATED,PIPE,NOMINAL,FIRST END FIRST END NOMINAL PIPE SIZE ACCOMMODATED THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE END WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 ACLHJ 04DIAMETER TUBE ACCOMMODATED,OUTSIDE,FIRST END FIRST END OUTSIDE DIAMETER TUBE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACLJJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,END,FIRST FIRST END THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AC21 ACLKA 13THREAD CLASS,END,FIRST FIRST END THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD. 1A MODE REPLY 0 ACLLD 13THREAD DIRECTION,END,FIRST FIRST END THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ACLMJ /D/ 04LENGTH,LEG,FIRST END FIRST END LEG LENGTH THE DISTANCE FROM THE CENTERLINE OF THE BODY TO THE END OF THE LEG. 2D AND 1B MODE REPLY21AA051AC20 ACLNJ 04DIAMETER,INSIDE,REDUCED PASSAGE,FIRST END FIRST END REDUCED PASSAGE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FIRST END REDUCED PASSAGE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACLPD /D/ 03DESIGNATION FOR WHICH DESIGNED,THICKNESS,PIPE WALL,FIRST END FIRST END PIPE WALL THICKNESS DESIGNATION FOR WHICH DESIGNED THE TERM USED TO DEFINE THE WALL THICKNESS CROSS-SECTIONAL DIMENSION OF PIPE OF VARIOUS MATERIAL AS REPRESENTED BY A SCHEDULE,THICKNESS CLASS,CLASS STRENGTH,OR WEIGHT DESIGNATION. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. SELECT REPLY CODE 10AA35 ACLQJ /D/ 04THICKNESS FOR WHICH DESIGNED,WALL,FIRST END TUBING FIRST END TUBING WALL THICKNESS FOR WHICH DESIGNED THE THICKNESS OF THE TUBING AS TAKEN FROM THE INSIDE SURFACE TO THE NEAREST OUTER SURFACE FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 ACLRD /D/ 19RELATIONSHIP WITH FIRST END,SECOND END SECOND END RELATIONSHIP WITH FIRST END INDICATES WHETHER OR NOT THE SECOND END IS IDENTICAL TO THE FIRST END. PLEASE USE MRC CQBB IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB78 ACLSD 18TYPE,CONNECTION,SECOND END SECOND END CONNECTION TYPE A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION. SELECT REPLY CODE 10AB76 ACLTL 16STYLE DESIGNATOR,END,SECOND SECOND END STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END. 1L MODE REPLY 0 ACLUJ 04HEIGHT,FACE,RAISED,SECOND END SECOND END RAISED FACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ACLVJ 04DIAMETER,FACE,RAISED,SECOND END SECOND END RAISED FACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACLWJ 04DIAMETER,RECESS,SECOND END SECOND END RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACLXJ 04DEPTH,RECESS,SECOND END SECOND END RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACLYL 16STYLE,SHAPE,SECOND END FLANGE SECOND END FLANGE SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE END FLANGE. 1L MODE REPLY 0 ACLZJ 04THICKNESS,FLANGE,SECOND END SECOND END FLANGE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE SECOND END FLANGE, IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ACMAJ 04LENGTH,FLANGE,SECOND END SECOND END FLANGE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SECOND END FLANGE, IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ACMBJ 04WIDTH,FLANGE,SECOND END SECOND END FLANGE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SECOND END FLANGE, IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ACMCJ /D/ 04RADIUS,END,SECOND END FLANGE SECOND END FLANGE END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ACMDJ 04WIDTH ACROSS FLATS,END,SECOND SECOND END WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 ACMEJ /D/ 04DIAMETER,BASKET BASKET DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BASKET,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACMFA 12QUANTITY,HOLE,BOLT,SECOND END SECOND END BOLT HOLE QUANTITY THE NUMBER OF BOLT HOLES PROVIDED ON THE ITEM. 1A MODE REPLY 0 ACMGJ 04DIAMETER,HOLE,BOLT,SECOND END SECOND END BOLT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACMHJ 04DIAMETER,CIRCLE,BOLT,SECOND END SECOND END BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACMJJ /D/ 04DISTANCE BETWEEN BOLT HOLES ALONG LENGTH,SECOND END SECOND END DISTANCE BETWEEN BOLT HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACMKJ /D/ 04DISTANCE BETWEEN BOLT HOLES ALONG WIDTH,SECOND END SECOND END DISTANCE BETWEEN BOLT HOLES ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACMLJ 04DIAMETER HOSE ACCOMMODATED,INSIDE,SECOND END SECOND END INSIDE DIAMETER HOSE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACMMJ 04DIAMETER HOSE ACCOMMODATED,OUTSIDE,SECOND END SECOND END OUTSIDE DIAMETER HOSE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACMNJ 04SIZE ACCOMMODATED,PIPE,NOMINAL,SECOND END SECOND END NOMINAL PIPE SIZE ACCOMMODATED THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE END WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 ACMPJ 04DIAMETER TUBE ACCOMMODATED,OUTSIDE,SECOND END SECOND END OUTSIDE DIAMETER TUBE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACMQJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,END,SECOND SECOND END THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AC21 ACMRA 13THREAD CLASS,END,SECOND SECOND END THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD. 1A MODE REPLY 0 ACMSD 13THREAD DIRECTION,END,SECOND SECOND END THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ACMTJ /D/ 04LENGTH,LEG,SECOND END SECOND END LEG LENGTH THE DISTANCE FROM THE CENTERLINE OF THE BODY TO THE END OF THE LEG. 2D AND 1B MODE REPLY21AA051AC20 ACMUJ 04DIAMETER,INSIDE,REDUCED PASSAGE,SECOND END SECOND END REDUCED PASSAGE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SECOND END REDUCED PASSAGE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACMVD /D/ 03DESIGNATION FOR WHICH DESIGNED,THICKNESS,PIPE WALL,SECOND END SECOND END PIPE WALL THICKNESS DESIGNATION FOR WHICH DESIGNED THE TERM USED TO DEFINE THE WALL THICKNESS CROSS-SECTIONAL DIMENSION OF PIPE OF VARIOUS MATERIAL AS REPRESENTED BY A SCHEDULE,THICKNESS CLASS,CLASS STRENGTH,OR WEIGHT DESIGNATION. SELECT REPLY CODE 10AA35 ACMWJ /D/ 04THICKNESS FOR WHICH DESIGNED,WALL,SECOND END TUBING SECOND END TUBING WALL THICKNESS FOR WHICH DESIGNED THE THICKNESS OF THE TUBING AS TAKEN FROM THE INSIDE SURFACE TO THE NEAREST OUTER SURFACE FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 ACMXD 19RELATIONSHIP WITH PRECEDING ENDS,THIRD END THIRD END RELATIONSHIP WITH PRECEDING ENDS INDICATES WHETHER OR NOT THE THIRD END IS IDENTICAL WITH FIRST OR SECOND END. SELECT REPLY CODE 10AB78 ACMYD 18TYPE,CONNECTION,THIRD END THIRD END CONNECTION TYPE A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION. SELECT REPLY CODE 10AB76 ACMZL 16STYLE DESIGNATOR,END,THIRD THIRD END STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END. 1L MODE REPLY 0 ACNAJ /D/ 04HEIGHT,FACE,RAISED,THIRD END THIRD END RAISED FACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ACNBJ /D/ 04DIAMETER,FACE,RAISED,THIRD END THIRD END RAISED FACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACNCJ /D/ 04DIAMETER,RECESS,THIRD END THIRD END RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACNDJ /D/ 04DEPTH,RECESS,THIRD END THIRD END RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACNED /D/ 18TYPE FOR WHICH DESIGNED,BEAM BEAM TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF BEAM FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AA78 ACNFL 16STYLE,SHAPE,THIRD END FLANGE THIRD END FLANGE SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE END FLANGE. 1L MODE REPLY 0 ACNGJ 04DIAMETER,OUTSIDE,THIRD END FLANGE THIRD END FLANGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACNHJ 04THICKNESS,FLANGE,THIRD END THIRD END FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ACNJJ /D/ 04LENGTH,FLANGE,THIRD END THIRD END FLANGE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACNKJ 04WIDTH,FLANGE,THIRD END THIRD END FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACNLJ /D/ 04RADIUS,END,THIRD END FLANGE THIRD END FLANGE END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ACNMJ /D/ 04WIDTH ACROSS FLATS,END,THIRD THIRD END WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 ACNNA 12QUANTITY,HOLE,BOLT,THIRD END THIRD END BOLT HOLE QUANTITY THE NUMBER OF BOLT HOLES PROVIDED ON THE ITEM. 1A MODE REPLY 0 ACNPJ 04DIAMETER,HOLE,BOLT,THIRD END THIRD END BOLT HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACNQJ 04DIAMETER,CIRCLE,BOLT,THIRD END THIRD END BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACNRJ /D/ 04DISTANCE BETWEEN BOLT HOLES ALONG LENGTH,THIRD END THIRD END DISTANCE BETWEEN BOLT HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACNSJ /D/ 04DISTANCE BETWEEN BOLT HOLES ALONG WIDTH,THIRD END THIRD END DISTANCE BETWEEN BOLT HOLES ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACNTJ /D/ 04DIAMETER HOSE ACCOMMODATED,INSIDE,THIRD END THIRD END INSIDE DIAMETER HOSE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACNUJ 04DIAMETER HOSE ACCOMMODATED,OUTSIDE,THIRD END THIRD END OUTSIDE DIAMETER HOSE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACNVJ 04SIZE ACCOMMODATED,PIPE,NOMINAL,THIRD END THIRD END NOMINAL PIPE SIZE ACCOMMODATED THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE END WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 ACNWJ 04DIAMETER TUBE ACCOMMODATED,OUTSIDE,THIRD END THIRD END OUTSIDE DIAMETER TUBE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACNXJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,END,THIRD THIRD END THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AC21 ACNYA 13THREAD CLASS,END,THIRD THIRD END THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD. 1A MODE REPLY 0 ACNZD /D/ 13THREAD DIRECTION,END,THIRD THIRD END THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. PLEASE USE MRC AAJF WITH ISAC TABLE 0036 IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA38 ACPAJ /D/ 04LENGTH,LEG,THIRD END THIRD END LEG LENGTH THE DISTANCE FROM THE CENTERLINE OF THE BODY TO THE END OF THE LEG. 2D AND 1B MODE REPLY21AA051AC20 ACPBJ /D/ 04DIAMETER,INSIDE,THIRD END REDUCED PASSAGE THIRD END REDUCED PASSAGE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE REDUCED PASSAGE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACPCD /D/ 03DESIGNATION FOR WHICH DESIGNED,THICKNESS,PIPE WALL,THIRD END THIRD END PIPE WALL THICKNESS DESIGNATION FOR WHICH DESIGNED THE TERM USED TO DEFINE THE WALL THICKNESS CROSS-SECTIONAL DIMENSION OF PIPE OF VARIOUS MATERIAL AS REPRESENTED BY A SCHEDULE,THICKNESS CLASS,CLASS STRENGTH,OR WEIGHT DESIGNATION. SELECT REPLY CODE 10AA35 ACPDJ /D/ 04THICKNESS FOR WHICH DESIGNED,WALL,THIRD END TUBING THIRD END TUBING WALL THICKNESS FOR WHICH DESIGNED A MEASUREMENT OF THE SMALLEST DIMENSION OF THE TUBING FROM THE INSIDE SURFACE TO THE NEAREST OUTER SURFACE FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ACPED 19RELATIONSHIP WITH PRECEDING ENDS,FOURTH END FOURTH END RELATIONSHIP WITH PRECEDING ENDS INDICATES WHETHER OR NOT THE FOURTH END IS IDENTICAL WITH THE FIRST,SECOND,OR THIRD END. SELECT REPLY CODE 10AB78 ACPFD 18TYPE,CONNECTION,FOURTH END FOURTH END CONNECTION TYPE A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION. SELECT REPLY CODE 10AB76 ACPGL 16STYLE DESIGNATOR,END,FOURTH FOURTH END STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END. 1L MODE REPLY 0 ACPHJ /D/ 04HEIGHT,FACE,RAISED,FOURTH END FOURTH END RAISED FACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ACPJJ /D/ 04DIAMETER,FACE,RAISED,FOURTH END FOURTH END RAISED FACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACPKJ /D/ 04DIAMETER,RECESS,FOURTH END FOURTH END RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACPLJ /D/ 04DEPTH,RECESS,FOURTH END FOURTH END RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACPML 16STYLE,SHAPE,FOURTH END FLANGE FOURTH END FLANGE SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE END FLANGE. 1L MODE REPLY 0 ACPNJ /D/ 04DIAMETER,OUTSIDE,FOURTH END FLANGE FOURTH END FLANGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACPPJ /D/ 04THICKNESS,FLANGE,FOURTH END FOURTH END FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ACPQJ /D/ 04WIDTH,FLANGE,FOURTH END FOURTH END FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACPRJ /D/ 04LENGTH,FLANGE,FOURTH END FOURTH END FLANGE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACPSJ /D/ 04RADIUS,END,FOURTH END FLANGE FOURTH END FLANGE END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ACPTJ /D/ 04WIDTH ACROSS FLATS,END,FOURTH FOURTH END WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 ACPUA 12QUANTITY,HOLE,BOLT,FOURTH END FOURTH END BOLT HOLE QUANTITY THE NUMBER OF BOLT HOLES PROVIDED ON THE ITEM. 1A MODE REPLY 0 ACPVJ 04DIAMETER,HOLE,BOLT,FOURTH END FOURTH END BOLT HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACPWJ /D/ 04DIAMETER,CIRCLE,BOLT,FOURTH END FOURTH END BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACPXJ /D/ 04DISTANCE BETWEEN BOLT HOLES ALONG LENGTH,FOURTH END FOURTH END DISTANCE BETWEEN BOLT HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACPYJ /D/ 04DISTANCE BETWEEN BOLT HOLES ALONG WIDTH,FOURTH END FOURTH END DISTANCE BETWEEN BOLT HOLES ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACPZJ /D/ 04DIAMETER HOSE ACCOMMODATED,INSIDE,FOURTH END FOURTH END INSIDE DIAMETER HOSE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACQAJ 04DIAMETER HOSE ACCOMMODATED,OUTSIDE,FOURTH END FOURTH END OUTSIDE DIAMETER HOSE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACQBJ 04SIZE ACCOMMODATED,PIPE,NOMINAL,FOURTH END FOURTH END NOMINAL PIPE SIZE ACCOMMODATED THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE END WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 ACQCJ 04DIAMETER TUBE ACCOMMODATED,OUTSIDE,FOURTH END FOURTH END OUTSIDE DIAMETER TUBE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACQDJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,END,FOURTH FOURTH END THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AC21 ACQEA 13THREAD CLASS,END,FOURTH FOURTH END THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD. 1A MODE REPLY 0 ACQFD /D/ 13THREAD DIRECTION,END,FOURTH FOURTH END THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. PLEASE USE MRC AAJF WITH ISAC TABLE 0036 IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA38 ACQGJ /D/ 04LENGTH,LEG,FOURTH END FOURTH END LEG LENGTH THE DISTANCE FROM THE CENTERLINE OF THE BODY TO THE END OF THE LEG. 2D AND 1B MODE REPLY21AA051AC20 ACQHJ /D/ 04DIAMETER,INSIDE,REDUCED PASSAGE,FOURTH END FOURTH END REDUCED PASSAGE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FOURTH END REDUCED PASSAGE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACQJD /D/ 03DESIGNATION FOR WHICH DESIGNED,THICKNESS,PIPE WALL,FOURTH END FOURTH END PIPE WALL THICKNESS DESIGNATION FOR WHICH DESIGNED THE TERM USED TO DEFINE THE WALL THICKNESS CROSS-SECTIONAL DIMENSION OF PIPE OF VARIOUS MATERIAL AS REPRESENTED BY A SCHEDULE,THICKNESS CLASS,CLASS STRENGTH,OR WEIGHT DESIGNATION. SELECT REPLY CODE 10AA35 ACQKJ /D/ 04THICKNESS FOR WHICH DESIGNED,WALL,FOURTH END TUBING FOURTH END TUBING WALL THICKNESS FOR WHICH DESIGNED THE THICKNESS OF THE TUBING AS TAKEN FROM THE INSIDE SURFACE TO THE NEAREST OUTER SURFACE FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 ACQLD /D/ 08LOCATION,JOINT,UNION UNION JOINT LOCATION INDICATES THE LOCATION OF THE UNION JOINT. SELECT REPLY CODE 10AE46 ACQMD /D/ 13THREAD LOCATION,BULKHEAD BULKHEAD THREAD LOCATION INDICATES THE LOCATION OF THE BULKHEAD THREAD. SELECT REPLY CODE 10AE46 ACQNJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,BULKHEAD BULKHEAD THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE BULKHEAD THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AC21 ACQPA /D/ 13THREAD CLASS,BULKHEAD BULKHEAD THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE,AND AN EXTERNAL OR INTERNAL BULKHEAD THREAD. 1A MODE REPLY 0 ACQQD /D/ 13THREAD DIRECTION,BULKHEAD BULKHEAD THREAD DIRECTION THE DIRECTION OF THE BULKHEAD THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION,WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ACQRJ /D/ 13THREAD LENGTH,BULKHEAD BULKHEAD THREAD LENGTH A MEASUREMENT OF THE EXTENT OF BULKHEAD THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS. 2D AND 1B MODE REPLY21AA051AC20 ACQSB /D/ 04ANGLE IN DEG,FLOW FLOW ANGLE IN DEG THE ANGLE THE FLOW IS TURNED FROM THE STRAIGHT FLOW,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ACQTJ /D/ 04DISTANCE CENTER TO CENTER,BEND BEND DISTANCE CENTER TO CENTER THE DISTANCE FROM THE CENTERLINE OF OPENING OF ONE END TO THE CENTERLINE OF OPENING OF OPPOSITE END. 2D AND 1B MODE REPLY21AA051AC20 ACQUA /D/ 12QUANTITY,INLET INLET QUANTITY THE NUMBER OF ADDITIONAL OPENINGS,EXCLUDING THE ENDS,WHICH ALLOWS THE FLOW OF SUBSTANCE INTO THE NORMAL FLOW. 1A MODE REPLY 0 ACQVD /D/ 08LOCATION,INLET INLET LOCATION INDICATES THE LOCATION OF THE INLET ON THE ITEM. SELECT REPLY CODE 10AE46 ACQWD 18TYPE,CONNECTION,INLET INLET CONNECTION TYPE A NARRATIVE DESCRIPTION OF THE TYPE OF INLET CONNECTION. SELECT REPLY CODE 10AB76 ACQXL /D/ 16STYLE DESIGNATOR,INLET INLET STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END. 1L MODE REPLY 0 ACQYJ /D/ 04HEIGHT,FACE,RAISED,INLET INLET RAISED FACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ACQZJ /D/ 04DIAMETER,FACE,RAISED,INLET INLET RAISED FACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACRAJ /D/ 04DIAMETER,RECESS,INLET INLET RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACRBJ /D/ 04DEPTH,RECESS,INLET INLET RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACRCA /D/ 16STYLE,SHAPE,INLET FLANGE INLET FLANGE SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE INLET FLANGE. 1A MODE REPLY 0 ACRDJ 04DIAMETER,OUTSIDE,INLET FLANGE INLET FLANGE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INLET FLANGE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACREA 18TYPE,FILTER FILTER TYPE INDICATES THE TYPE OF FILTER PROVIDED. 1A MODE REPLY 0 ACRFJ 04THICKNESS,FLANGE,INLET INLET FLANGE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF AN INLET FLANGE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ACRGJ 04LENGTH,FLANGE,INLET INLET FLANGE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE INLET FLANGE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ACRHJ 04WIDTH,FLANGE,INLET INLET FLANGE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE INLET FLANGE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ACRJJ /D/ 04RADIUS,END,INLET FLANGE INLET FLANGE END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ACRKJ /D/ 04WIDTH ACROSS FLATS,INLET INLET WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 ACRLA 12QUANTITY,HOLE,BOLT,INLET INLET BOLT HOLE QUANTITY THE NUMBER OF INLET BOLT HOLES ON THE ITEM. 1A MODE REPLY 0 ACRMJ 04DIAMETER,HOLE,INLET BOLT INLET BOLT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN INLET BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACRNJ 04DIAMETER,CIRCLE,INLET BOLT INLET BOLT CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN INLET BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACRPJ /D/ 04DISTANCE BETWEEN BOLT HOLES ALONG LENGTH,INLET INLET DISTANCE BETWEEN BOLT HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACRQJ /D/ 04DISTANCE BETWEEN BOLT HOLES ALONG WIDTH,INLET INLET DISTANCE BETWEEN BOLT HOLES ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACRRJ /D/ 04DIAMETER HOSE ACCOMMODATED,INSIDE,INLET INLET INSIDE DIAMETER HOSE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACRSJ /D/ 04DIAMETER HOSE ACCOMMODATED,OUTSIDE,INLET INLET OUTSIDE DIAMETER HOSE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACRTJ 04SIZE ACCOMMODATED,PIPE,NOMINAL,INLET INLET NOMINAL PIPE SIZE ACCOMMODATED THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE INLET WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 ACRUJ /D/ 04DIAMETER TUBE ACCOMMODATED,OUTSIDE,INLET INLET OUTSIDE DIAMETER TUBE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACRVJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,INLET INLET THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE INLET THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AC21 ACRWA 13THREAD CLASS,INLET INLET THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD. 1A MODE REPLY 0 ACRXD /D/ 13THREAD DIRECTION,INLET INLET THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ACRYJ /D/ 04LENGTH,LEG,INLET INLET LEG LENGTH THE DISTANCE FROM THE CENTERLINE OF THE BODY TO THE END OF THE LEG. 2D AND 1B MODE REPLY21AA051AC20 ACRZJ /D/ 04DIAMETER,INSIDE,REDUCED PASSAGE,INLET INLET REDUCED PASSAGE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INLET REDUCED PASSAGE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACSAD /D/ 03DESIGNATION FOR WHICH DESIGNED,THICKNESS,PIPE WALL,INLET INLET PIPE WALL THICKNESS DESIGNATION FOR WHICH DESIGNED THE TERM USED TO DEFINE THE WALL THICKNESS CROSS-SECTIONAL DIMENSION OF PIPE OF VARIOUS MATERIAL AS REPRESENTED BY A SCHEDULE,THICKNESS CLASS,CLASS STRENGTH,OR WEIGHT DESIGNATION. SELECT REPLY CODE 10AA35 ACSBJ /D/ 04THICKNESS FOR WHICH DESIGNED,WALL,INLET TUBING INLET TUBING WALL THICKNESS FOR WHICH DESIGNED THE THICKNESS OF THE INLET TUBING AS TAKEN FROM THE INSIDE SURFACE TO THE NEAREST OUTER SURFACE FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 ACSCA /D/ 12QUANTITY,CLEANOUT CLEANOUT QUANTITY THE NUMBER OF CLEANOUTS IN THE ITEM. 1A MODE REPLY 0 ACSDD /D/ 08LOCATION,CLEANOUT CLEANOUT LOCATION INDICATES THE LOCATION OF THE CLEANOUT IN THE BODY OF THE ITEM. SELECT REPLY CODE 10AE46 ACSEA /D/ 12QUANTITY,VENT VENT QUANTITY THE NUMBER OF VENTS IN THE ITEM. 1A MODE REPLY 0 ACSFD 18TYPE,SWEEP SWEEP TYPE INDICATES THE TYPE OF SWEEP WHICH REFERS TO THE TURN THE BRANCH MAKES FROM THE RUN. SELECT REPLY CODE 10AB79 ACSGD /D/ 18TYPE,SEAT SEAT TYPE INDICATES THE TYPE OF SEAT IN THE ITEM. PLEASE USE MRC BYJF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB80 ACSHD /D/ 09MATERIAL,SEAT SEAT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SEATING SURFACES ARE FABRICATED. PLEASE USE MRC CYBM OR MATT AND USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 ACSJD /D/ 14SHAPE,FLANGE,COUPLING COUPLING FLANGE SHAPE THE OUTSIDE CONFIGURATION OF THE FLANGE. SELECT REPLY CODE 10AD07 ACSKD /D/ 18TYPE,BEARING BEARING TYPE INDICATES THE TYPE OF BEARINGS FURNISHED. PLEASE USE MRC BYDT IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB81 ACSLD 14SHAPE,FACILITY,WRENCHING WRENCHING FACILITY SHAPE THE PHYSICAL CONFIGURATION OF THE FACILITY UTILIZED TO ASSEMBLE OR DISASSEMBLE THE ITEM. SELECT REPLY CODE 10AD07 ACSMD /D/ 18TYPE,FACILITY,WRENCHING WRENCHING FACILITY TYPE INDICATES THE TYPE OF FACILITY UTILIZED TO ASSEMBLE OR DISASSEMBLE THE ITEM. SELECT REPLY CODE 10AB82 ACSND /D/ 07REMOVABILITY,BEARING BEARING REMOVABILITY AN INDICATION OF WHETHER OR NOT THE BEARING/S/ IS REMOVABLE. SELECT REPLY CODE 10AC29 ACSPD 18TYPE,REDUCER REDUCER TYPE REFERS TO THE LOCATION OF THE ENDS WHETHER ON THE SAME CENTERLINE (CONCENTRIC) OR ON DIFFERENT CENTERLINES (ECCENTRIC). SELECT REPLY CODE 10AB83 ACSQD /D/ 18TYPE,FITTING,DRAINAGE DRAINAGE FITTING TYPE INDICATES WHETHER THE ITEM IS DESIGNED TO BE USED AS A CLOSET (SANITARY) TYPE OR PLAIN DRAINAGE FITTING. SELECT REPLY CODE 10AB84 ACSRD /D/ 18TYPE,SEAL SEAL TYPE INDICATES THE TYPE OF SEAL UTILIZED WHEN THE STEM AND SPUD ARE JOINED TOGETHER IN THE ASSEMBLED COUPLING. SELECT REPLY CODE 10AB85 ACSSD /D/ 07DEFLATOR,RELEASE,AIR AIR RELEASE DEFLATOR INDICATES WHETHER OR NOT THE ITEM HAS AN INTERNAL DEVICE /DEFLATOR/ WHICH ALLOWS THE AIR TO BE RELEASED. SELECT REPLY CODE 10AA49 ACSTD 18TYPE,END,MOUNTING MOUNTING END TYPE INDICATES THE TYPE OF END WHICH IS USED TO MOUNT THE ITEM. SELECT REPLY CODE 10AB86 ACSUJ 04SIZE FOR WHICH DESIGNED,PIPE,NOMINAL NOMINAL PIPE SIZE FOR WHICH DESIGNED THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF PIPE FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AA05 ACSVJ 04DIAMETER FOR WHICH DESIGNED,OUTSIDE,TUBE TUBE OUTSIDE DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBE FOR WHICH DESIGNED,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACSWD /D/ 07FACILITY,STOP,INTERNAL PIPE INTERNAL PIPE STOP FACILITY AN INDICATION OF WHETHER OR NOT A SLIP JOINT TYPE COUPLING HAS AN INTERNAL FACILITY THAT STOPS THE PIPE AT A PREDETERMINED DISTANCE. SELECT REPLY CODE 10AA49 ACSXJ 04DISTANCE,OFFSET OFFSET DISTANCE THE DISTANCE OF OFFSET IN THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ACSYJ /D/A19ITEMS AND QUANTITY,FURNISHED FURNISHED ITEMS AND QUANTITY THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE. PLEASE USE MRC TMQY IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1A MODE REPLY12AB87 ACSZJ 04DIAMETER ACCOMMODATED,MEMBER,MATING MATING MEMBER DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF ACCOMMODATION FOR THE MATING MEMBER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACTAL 16STYLE,NUT NUT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE NUT. 1L MODE REPLY 0 ACTBB /D/ 04ANGLE IN DEG,SEAT,CONE CONE SEAT ANGLE IN DEG NONE. 1B MODE REPLY 0 ACTCJ 04RADIUS,SEAT,BALL BALL SEAT RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ACTDJ 04DIAMETER,NUT NUT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACTEB /D/ 04ANGLE IN DEG,SEAT,FIRST END FIRST END SEAT ANGLE IN DEG THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. PLEASE USE MRC CQRB WITH ISAC TABLE 0036 IN PLACE OF THIS DISCONTINUED MRC. 1B MODE REPLY 0 ACTFB /D/ 04ANGLE IN DEG,SEAT,SECOND END SECOND END SEAT ANGLE IN DEG THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. PLEASE USE MRC CRCN OR CQRB WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. 1B MODE REPLY 0 ACTGB /D/ 04ANGLE IN DEG,SEAT,THIRD END THIRD END SEAT ANGLE IN DEG THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. PLEASE USE MRC CQRB WITH ISAC TABLE 0036 IN PLACE OF THIS DISCONTINUED MRC. 1B MODE REPLY 0 ACTHB /D/ 04ANGLE IN DEG,SEAT,FOURTH END FOURTH END SEAT ANGLE IN DEG THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. PLEASE USE MRC CQRB WITH ISAC TABLE 0036 IN PLACE OF THIS DISCONTINUED MRC. 1B MODE REPLY 0 ACTJB /D/ 04ANGLE IN DEG,SEAT,INLET INLET SEAT ANGLE IN DEG THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ACTKJ 04RADIUS,SEAT,FIRST END FIRST END SEAT RADIUS THE RADIUS OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS. 2D AND 1B MODE REPLY21AA051AC20 ACTLJ 04RADIUS,SEAT,SECOND END SECOND END SEAT RADIUS THE RADIUS OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS. 2D AND 1B MODE REPLY21AA051AC20 ACTMJ /D/ 04RADIUS,SEAT,THIRD END THIRD END SEAT RADIUS THE RADIUS OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS. 2D AND 1B MODE REPLY21AA051AC20 ACTNJ /D/ 04RADIUS,SEAT,FOURTH END FOURTH END SEAT RADIUS THE RADIUS OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS. 2D AND 1B MODE REPLY21AA051AC20 ACTPJ /D/ 04RADIUS,SEAT,INLET INLET SEAT RADIUS THE RADIUS OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS. 2D AND 1B MODE REPLY21AA051AC20 ACTQD /D/ 18TYPE,PATTERN,PIPE FITTING PIPE FITTING PATTERN TYPE THE PHYSICAL CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE GENERAL APPEARANCE OF THE PIPE FITTING AS RELATED TO A REFERENCE DRAWING. SELECT REPLY CODE 10AB88 ACTRJ /D/ 04DIAMETER,INSIDE,OPENING OPENING INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO SURFACES OF A CIRCULAR OPENING,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ACTSD /D/ 18TYPE FOR WHICH DESIGNED,SUSPENSION SUSPENSION TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF SUSPENSION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 ACTTJ /D/ 04HEIGHT,BODY BODY HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BODY,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 ACTUJ 04LENGTH,OVERALL,BASE BASE OVERALL LENGTH THE OVERALL DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BASE. 1D AND 1B MODE REPLY11AA05 ACTVJ 04WIDTH,BASE BASE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BASE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 ACTWJ 04HEIGHT,DOME DOME HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ACTXJ /D/ 04WIDTH,HOLE,ACCOMMODATION ACCOMMODATION HOLE WIDTH NONE. 1D AND 1B MODE REPLY11AA05 ACTYJ /D/ 04DIAMETER,INSIDE,ACCOMMODATION HOLE ACCOMMODATION HOLE INSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACTZJ /D/ 04DISTANCE FROM MOUNTING HOLE CENTER TO BASE EDGE,FIRST FIRST DISTANCE FROM MOUNTING HOLE CENTER TO BASE EDGE NONE. 1D AND 1B MODE REPLY11AA05 ACUAJ /D/ 04RADIUS RADIUS NONE. 1D AND 1B MODE REPLY11AA05 ACUBJ /D/ 04DISTANCE TO BASE EDGE,OPENING,INSIDE INSIDE OPENING DISTANCE TO BASE EDGE NONE. 1D AND 1B MODE REPLY11AA05 ACUCJ /D/ 04DIAMETER,OUTSIDE,BASE END BASE END OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 ACUDJ /D/ 04DISTANCE FROM MOUNTING HOLE CENTER TO BASE EDGE,SECOND SECOND DISTANCE FROM MOUNTING HOLE CENTER TO BASE EDGE NONE. 1D AND 1B MODE REPLY11AA05 ACUEJ 04LENGTH,EXTENDED EXTENDED LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ITEM WHEN EXTENDED. 1D AND 1B MODE REPLY11AA05 ACUFJ /D/ 04LENGTH,COMPRESSED COMPRESSED LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACUGJ /D/ 04LENGTH,EFFECTIVE EFFECTIVE LENGTH NONE. 1D AND 1B MODE REPLY11AA05 ACUHJ /D/ 04DISTANCE BETWEEN MOUNTING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES NONE. 1D AND 1B MODE REPLY11AA05 ACUJJ /D/ 04DIAMETER,GRIP GRIP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ACUKJ 04WIDTH,TOP TOP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TOP,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 ACULJ /D/ 04LENGTH,TONGUE TONGUE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TONGUE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 ACUMJ 04WIDTH,STRAP STRAP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A STRAP,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 ACUND /D/ 11METHOD,MOUNTING MOUNTING METHOD THE MEANS OF ATTACHING THE ITEM. THIS MRC IS BEING DISCONTINUED. PLEASE USE MRC AXGY IF AVAILABLE. SELECT REPLY CODE 10AB89 ACUPA 12QUANTITY,DEVICE,MOUNTING MOUNTING DEVICE QUANTITY THE NUMBER OF MOUNTING DEVICES USED AS A MEANS OF ATTACHING THE ITEM. 1A MODE REPLY 0 ACUQB 10VOLTAGE RATING IN VOLTS,CURRENT,ALTERNATING ALTERNATING CURRENT VOLTAGE RATING IN VOLTS THE ALTERNATING CURRENT VOLTAGE FOR WHICH THE ITEM IS RATED,EXPRESSED IN VOLTS. 1B MODE REPLY 0 ACURB 10VOLTAGE RATING IN VOLTS,CURRENT,DIRECT DIRECT CURRENT VOLTAGE RATING IN VOLTS THE DIRECT CURRENT VOLTAGE FOR WHICH THE ITEM IS RATED,EXPRESSED IN VOLTS. 1B MODE REPLY 0 ACUSB 10CURRENT RATING IN AMPS,ALTERNATING ALTERNATING CURRENT RATING IN AMPS THE ALTERNATING CURRENT RATING FOR WHICH THE ITEM IS RATED,EXPRESSED IN AMPERES. 1B MODE REPLY 0 ACUTB 10CURRENT RATING IN AMPS,DIRECT DIRECT CURRENT RATING IN AMPS THE DIRECT CURRENT RATING FOR WHICH THE ITEM IS RATED,EXPRESSED IN AMPERES. 1B MODE REPLY 0 ACUUJ 04WIDTH,BASE BASE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BASE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ACUVJ 04SIZE ACCOMMODATED,TRADE,CONDUIT CONDUIT TRADE SIZE ACCOMMODATED THE STANDARD NOMINAL SIZE DESIGNATION THAT INDICATES THE SPECIFIC ACTUAL INSIDE DIAMETER OF THE CONDUIT. 1D AND 1B MODE REPLY11AA05 ACUWD 11METHOD,SEALING SEALING METHOD THE MEANS BY WHICH THE ITEM IS SEALED. SELECT REPLY CODE 10AB90 ACUXD /D/ 18TYPE ACCOMMODATED,CABLE/CONDUIT CABLE/CONDUIT TYPE ACCOMMODATED INDICATES THE TYPE OF CABLE OR CONDUIT ACCOMMODATED. SELECT REPLY CODE 10AB91 ACUYD /D/ 09MATERIAL,INSULATOR INSULATOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INSULATOR IS FABRICATED. SELECT REPLY CODE 10AD09 ACUZD /D/ 13THREAD LOCATION,BASE BASE THREAD LOCATION AN INDICATION OF WHETHER THE BASE IS INTERNALLY AND/OR EXTERNALLY THREADED. SELECT REPLY CODE 10AE46 ACVAJ /D/ 13THREAD SIZE,BASE BASE THREAD SIZE DESIGNATES THE BASE THREAD DIAMETER AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1B MODE REPLY12AC21 ACVBJ /D/ 13THREAD LENGTH,BASE BASE THREAD LENGTH A MEASUREMENT OF THE EXTENT OF BASE THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS. 1D AND 1B MODE REPLY11AA05 ACVCD /D/ 13THREAD DIRECTION,BASE BASE THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION,WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ACVDD /D/ 07FEATURE,LOADED,SPRING SPRING LOADED FEATURE AN INDICATION OF WHETHER OR NOT A SPRING LOADED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ACVED /D/ 02DESIGN,USAGE USAGE DESIGN INDICATES THE DESIGNED USE OF THE ITEM. PLEASE USE MRC ALBY IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB92 ACVFD 18TYPE,LID,INSULATOR INSULATOR LID TYPE INDICATES THE TYPE OF INSULATOR LID FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AB93 ACVGA 12QUANTITY,ACCOMMODATION,INSULATOR INSULATOR ACCOMMODATION QUANTITY THE NUMBER OF INSULATOR ACCOMMODATIONS PROVIDED ON THE ITEM. 1A MODE REPLY 0 ACVHD /D/ 18TYPE,LUG,AERIAL AERIAL LUG TYPE INDICATES THE TYPE OF AERIAL LUG FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AB94 ACVJD /D/ 18TYPE,FITTING,ENTRANCE ENTRANCE FITTING TYPE INDICATES THE TYPE OF ENTRANCE FITTING FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AB95 ACVKD /D/ 07SWITCH,COMPONENT COMPONENT SWITCH AN INDICATION OF WHETHER OR NOT A COMPONENT SWITCH IS INCLUDED. SELECT REPLY CODE 10AA49 ACVLJ A04SIZE,CONDUCTOR CONDUCTOR SIZE THE WIRE GAGE DESIGNATION AND THE GAGE NUMBER USED TO DESCRIBE THE CONDUCTOR SIZE. 1D AND 1A MODE REPLY11AB96 ACVMD /D/ 18TYPE,BASE BASE TYPE INDICATES THE TYPE OF BASE FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AB97 ACVNJ 04LENGTH,NUT NUT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE NUT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ACVPD /D/ 09MATERIAL,FILLING FILLING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FILLING IS FABRICATED. SELECT REPLY CODE 10AD09 ACVQD /D/ 07STERILIZED STERILIZED INDICATES THAT THE ITEM HAS OR HAS NOT BEEN PROCESSED FOR AN ASEPTIC CONDITION. SELECT REPLY CODE 10AA89 ACVRJ 04WIDTH,SHANK SHANK WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SHANK,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ACVSJ 04THICKNESS,SHANK SHANK THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE SHANK,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ACVTJ 04DISTANCE BETWEEN PRONGS,INSIDE INSIDE DISTANCE BETWEEN PRONGS NONE. 2D AND 1B MODE REPLY21AA051AC20 ACVUJ 04DIAMETER,STOCK STOCK DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE STOCK,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACVVJ 04WIDTH,STOCK STOCK WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE STOCK,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ACVWJ 04THICKNESS,STOCK STOCK THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE STOCK,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ACVXA 19MARKING,HEAD HEAD MARKING NUMBERS AND/OR LETTERS ON THE HEAD OF AN ITEM. 1A MODE REPLY 0 ACVYD /D/ 07HEAD,DECORATIVE DECORATIVE HEAD INDICATES WHETHER OR NOT THE HEAD OF AN ITEM HAS BEEN EMBELLISHED FOR EXPOSED APPLICATIONS. SELECT REPLY CODE 10AA89 ACVZD /D/ 09MATERIAL,CAP CAP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CAP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 ACWAD 01COLOR,HEAD HEAD COLOR THE HUE OR TINT OF THE HEAD INCLUDING ANY PLATING OR COATING. SELECT REPLY CODE 10AD06 ACWBD /D/ 14SHAPE,STOCK STOCK SHAPE THE SHAPE OF THE MATERIAL UTILIZED IN THE FABRICATION OF THE ITEM. SELECT REPLY CODE 10AD07 ACWCJ 04DIAMETER,INSIDE,COMPLETELY CLOSED STAPLE COMPLETELY CLOSED STAPLE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CLOSED STAPLE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACWDJ /D/ 11METHOD AND LENGTH,MEASURING MEASURING METHOD AND LENGTH THE METHOD USED AND THE DIMENSION MEASURED PARALLEL TO THE LONGITUDINAL AXIS WHICH ESTABLISHES THE ACCEPTABLE LENGTH OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC24 ACWEJ /D/ 04HEIGHT,OVERALL,BODY BODY OVERALL HEIGHT THE VERTICAL MEASUREMENT OF THE BODY FROM THE TOP TO BOTTOM. EXCLUDES PLUG HEAD. 1D AND 1B MODE REPLY11AA05 ACWFD /D/ 18TYPE,INLET,SIDE SIDE INLET TYPE INDICATES THE TYPE OF SIDE INLET. SELECT REPLY CODE 10AB98 ACWGD /D/ 08LOCATION,INLET,SIDE SIDE INLET LOCATION INDICATES THE LOCATION OF THE SIDE INLET,RELATIVE TO THE HUB,SPIGOT,AND/OR BRANCH. SELECT REPLY CODE 10AA38 ACWHJ 04SIZE ACCOMMODATED,PIPE,NOMINAL,SIDE INLET SIDE INLET NOMINAL PIPE SIZE ACCOMMODATED THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE SIDE INLET WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 ACWJJ /D/ 13THREAD SIZE AND SERIES/TYPE DESIGNATOR,INLET,SIDE SIDE INLET THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE SIDE INLET THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1B MODE REPLY12AC21 ACWKD /D/ 13THREAD DIRECTION,INLET,SIDE SIDE INLET THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ACWLD /D/ 18TYPE,INLET,HEEL HEEL INLET TYPE INDICATES THE TYPE OF HEEL INLET. SELECT REPLY CODE 10AB98 ACWMD /D/ 08LOCATION,INLET,HEEL HEEL INLET LOCATION INDICATES THE LOCATION OF THE HEEL INLET,RELATIVE TO THE HUB,SPIGOT,AND/OR BRANCH. SELECT REPLY CODE 10AE46 ACWNJ 04SIZE ACCOMMODATED,PIPE,NOMINAL,HEEL INLET HEEL INLET NOMINAL PIPE SIZE ACCOMMODATED THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE HEEL INLET WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 ACWPJ /D/ 13THREAD SIZE AND SERIES/TYPE DESIGNATOR,INLET,HEEL HEEL INLET THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE HEEL INLET THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1B MODE REPLY12AC21 ACWQD /D/ 13THREAD DIRECTION,INLET,HEEL HEEL INLET THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION,WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ACWRD /D/ 18TYPE,OUTLET,VENT VENT OUTLET TYPE INDICATES THE TYPE OF VENT OUTLET. SELECT REPLY CODE 10AB98 ACWSJ 04SIZE ACCOMMODATED,PIPE,NOMINAL,VENT VENT NOMINAL PIPE SIZE ACCOMMODATED THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE VENT WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 ACWTJ /D/ 13THREAD SIZE AND SERIES/TYPE DESIGNATOR,VENT VENT THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE VENT THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1B MODE REPLY12AC21 ACWUD /D/ 13THREAD DIRECTION,VENT VENT THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION,WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ACWVJ /D/ 04SIZE ACCOMMODATED,PIPE,NOMINAL,CLEANOUT CLEANOUT NOMINAL PIPE SIZE ACCOMMODATED THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE DIAMETER OF THE PIPE. 1D AND 1B MODE REPLY11AA05 ACWWJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CLEANOUT CLEANOUT THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE CLEANOUT THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AC21 ACWXD /D/ 13THREAD DIRECTION,CLEANOUT CLEANOUT THREAD DIRECTION THE DRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ACWYD /D/ 09MATERIAL,PLUG,SCREW SCREW PLUG MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SCREW PLUG IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ACWZJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,PLUG,SCREW SCREW PLUG THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE SCREW PLUG THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AC21 ACXAD /D/ 08LOCATION,DRIVE,SCREW PLUG SCREW PLUG DRIVE LOCATION INDICATES WHETHER THE SCREW PLUG DRIVE IS INTERNALLY OR EXTERNALLY LOCATED. SELECT REPLY CODE 10AE46 ACXBD /D/ 14SHAPE,DRIVE,SCREW PLUG SCREW PLUG DRIVE SHAPE THE PHYSICAL CONFIGURATION OF THE WRENCHING FACILITY TO ALLOW INSERTION OR REMOVAL OF THE ITEM. SELECT REPLY CODE 10AD07 ACXCJ 03DESIGNATION,SIZE,INDUSTRIAL PIPE FITTING INDUSTRIAL PIPE FITTING SIZE DESIGNATION THE NOMINAL SIZE DESIGNATION USED BY INDUSTRY TO SPECIFY SIZES OF PIPE FITTING PATTERNS OF VARIOUS CONFIGURATIONS. 1D AND 1B MODE REPLY11AA05 ACXDL 16STYLE,RING RING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE RING. 1L MODE REPLY 0 ACXED /D/ 19CENTRICITY,RING RING CENTRICITY STATE OF BEING ECCENTRIC /INSIDE AND OUTSIDE DIAMETER NOT HAVING THE SAME CENTER/ OR CONCENTRIC /INSIDE AND OUTSIDE DIAMETER HAVING THE SAME CENTER/. SELECT REPLY CODE 10AB83 ACXFJ 04THICKNESS,WALL,RADIAL RADIAL WALL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ACXGJ 04THICKNESS,WALL,LARGEST RADIAL LARGEST RADIAL WALL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ACXHJ 04THICKNESS,WALL,SMALLEST RADIAL SMALLEST RADIAL WALL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ACXJJ /D/ 04WIDTH,OVERALL OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACXKJ 04THICKNESS,EDGE,OUTER OUTER EDGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ACXLL 16STYLE,HOLE,PIN PIN HOLE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PIN HOLE. 1L MODE REPLY 0 ACXMD 18TYPE,PASSAGE,OIL OIL PASSAGE TYPE INDICATES THE TYPE OF OIL PASSAGE INCLUDED ON THE ITEM. SELECT REPLY CODE 10AB99 ACXNA /D/ 12QUANTITY,PASSAGE,OIL OIL PASSAGE QUANTITY THE NUMBER OF OIL PASSAGES LOCATED IN THE ITEM. 1A MODE REPLY 0 ACXPD /D/ 08LOCATION,PASSAGE,OIL OIL PASSAGE LOCATION INDICATES THE LOCATION OF THE OIL PASSAGE IN THE ITEM. SELECT REPLY CODE 10AE46 ACXQJ 04LENGTH,SLOT,PIN HOLE PIN HOLE SLOT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACXRJ 04DEPTH,PIN HOLE,RING WIDTH RING WIDTH PIN HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACXSJ 04DISTANCE FROM PIN HOLE CENTERLINE TO RING JOINT CENTERLINE DISTANCE FROM PIN HOLE CENTERLINE TO RING JOINT CENTERLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 ACXTJ 04RADIUS,CORNER,PIN HOLE PIN HOLE CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ACXUJ 04DIAMETER,PINHOLE PINHOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PINHOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ACXVJ 04DEPTH,PIN HOLE,RING WALL THICKNESS RING WALL THICKNESS PIN HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACXWJ 04ANGLE,HOLE,PIN PIN HOLE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 ACXXJ /D/ 04WIDTH,SLOT,PIN PIN SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ACXYD 18TYPE,CHIP,PROCESSOR PROCESSOR CHIP TYPE INDICATES THE TYPE OF PROCESSING CHIP INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA01 ACXZJ 04DIAMETER,BORE,STANDARD STANDARD BORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CYLINDER /ENGINE,COMPRESSOR,OR THE LIKE/,AND TERMINATES AT THE INSIDE DIAMETER. 1D AND 1B MODE REPLY11AA05 ACYAJ 10OVERSIZE,DIAMETER,BORE BORE DIAMETER OVERSIZE THE MEASURED AMOUNT THAT THE OVERSIZE BORE EXCEEDS THE STANDARD BORE DIAMETER. 1D AND 1B MODE REPLY11AA05 ACYBJ 04THICKNESS,BASE BASE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A BASE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ACYCJ 19SPEED,CLOCK,PROCESSOR PROCESSOR CLOCK SPEED THE CLOCK SPEED AT WHICH THE ITEM PROCESSES INFORMATION. 1D AND 1B MODE REPLY13AK09 ACYDJ 13THREAD PITCH IN MILLIMETERS AND LOCATION THREAD PITCH IN MILLIMETERS AND LOCATION THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS, EXPRESSED IN MILLIMETERS, AND THE THREAD LOCATION. 1D AND 1B MODE REPLY13AN73 ACYED 19FUNCTION,TRANSFORMER TRANSFORMER FUNCTION A DESIGNATION OF THE TYPE OF CIRCUIT OPERATIONAL PERFORMANCE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AC00 ACYFD 18TYPE,INDUCTANCE INDUCTANCE TYPE INDICATES THE TYPE OF INDUCTANCE INCLUDED ON THE ITEM. SELECT REPLY CODE 10AC01 ACYGB /D/ 19NUMBER,GAUGE,METRIC METRIC GAUGE NUMBER A NUMBER INDICATING THE SIZE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1B MODE REPLY 0 ACYHH /D/ 18TYPE PER FUNCTION,WINDING WINDING TYPE PER FUNCTION THE SPECIFIC ARRANGEMENT IN WHICH WIRE IS WOUND ON A FORM OR IS FORMED BY WINDING,PER FUNCTION. 2D MODE REPLY 22AC022AH19 ACYJJ /D/A12QUANTITY PER FUNCTION,PI PI QUANTITY PER FUNCTION THE NUMBER OF INDIVIDUAL WASHER-SHAPED COILS PER FUNCTION WOUND WITH A CONTINUOUS CONDUCTOR ON A SINGLE FORM. 1D AND 1A MODE REPLY12AH19 ACYKA 12QUANTITY,ORIFICE ORIFICE QUANTITY THE NUMBER OF ORIFICES PROVIDED. 1A MODE REPLY 0 ACYLD /D/ 18TYPE,WINDING,PRIMARY PRIMARY WINDING TYPE THE DESCRIPTIVE DESIGNATION OF THE PRIMARY WINDING. SELECT REPLY CODE 10AC04 ACYMH /D/ 19TAPS PER FUNCTION,WINDING WINDING TAPS PER FUNCTION THE POINTS BETWEEN THE END TERMINALS PER FUNCTION OF A WINDING THAT PROVIDE ELECTRICAL CONNECTION TO INTERMEDIATE VALUES OF THE TOTAL WINDING. 2D MODE REPLY 21AC052AH19 ACYNJ 10RATING,VOLTAGE,AC AC VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,OF ROOT MEAN SQUARE POTENTIAL FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY21AB631AC20 ACYPF /D/T10TOLERANCE IN PERCENT,VOLTAGE,AC AC VOLTAGE TOLERANCE IN PERCENT THE LIMITS OF PERMISSIBLE VARIATION IN ROOT MEAN SQUARE POTENTIAL VALUE OF AN ITEM FROM ITS RATED VALUE,EXPRESSED IN PERCENT. 1F MODE REPLY 0 ACYQJ /D/ 10VOLTAGE RATING PER FUNCTION,PEAK PEAK VOLTAGE RATING PER FUNCTION THE MAXIMUM INSTANTANEOUS VOLTAGE PER FUNCTION FOR WHICH AN ITEM IS RATED. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 2D AND 1B MODE REPLY21AB632AH19 ACYRJ 10RATING,VOLTAGE,DC DC VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,OF DIRECT CURRENT POTENTIAL FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY21AB631AC20 ACYSJ /D/ 10CURRENT RATING CURRENT RATING THE AMOUNT OF CURRENT FOR WHICH THE ITEM IS RATED. 3D AND 1B MODE REPLY31AC301AB621AC20 ACYTJ 10CURRENT RATING,PEAK PEAK CURRENT RATING THE MAXIMUM INSTANTANEOUS CURRENT WHICH FLOWS IN AN ITEM DURING A COMPLETE CYCLE. 1D AND 1B MODE REPLY11AC30 ACYUB /D/ 10RESISTANCE RATING IN OHMS,DC DC RESISTANCE RATING IN OHMS THE MAXIMUM OPPOSITION TO THE FLOW OF DIRECT CURRENT OFFERED BY AN ITEM,EXPRESSED IN OHMS. 1B MODE REPLY 0 ACYVJ 10INDUCTANCE RATING INDUCTANCE RATING THE VALUE(S) OF INDUCTANCE INHERENT IN THE ITEM. 2D AND 1B MODE REPLY21AC311AC20 ACYWJ 10IMPEDANCE RATING IN OHMS IMPEDANCE RATING IN OHMS THE TOTAL OPPOSITION /RESISTIVE AND REACTIVE/ WHICH THE ITEM OFFERS TO THE FLOW OF AN ALTERNATING CURRENT,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 ACYXJ /D/ 10CAPACITY,OIL,WASTE WASTE OIL CAPACITY THE RATED CAPACITY OF THE WASTE OIL. 1D AND 1B MODE REPLY12AG67 ACZAH /D/ 19DEVICE PER FUNCTION,PROTECTION,OVERLOAD OVERLOAD PROTECTION DEVICE PER FUNCTION THE MEANS PROVIDED PER FUNCTION TO PREVENT OVERLOAD DAMAGE TO THE WINDINGS OF AN ITEM. 2D MODE REPLY 21AC082AH19 ACZBJ 10FREQUENCY RATING FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH AN ITEM IS RATED. 2D AND 1B MODE REPLY21AC321AC20 ACZCD 19RELATIONSHIP,PHASE,INPUT-OUTPUT INPUT-OUTPUT PHASE RELATIONSHIP THE RELATIONSHIP OF THE PHASE INPUT TO THE PHASE OUTPUT OF AN ALTERNATING CURRENT. SELECT REPLY CODE 10AE07 ACZDD 18TYPE,CONNECTION,TRANSFORMER WINDING TRANSFORMER WINDING CONNECTION TYPE INDICATES THE TYPE OF CONNECTING WINDINGS IN A TRANSFORMER TO BE POWERED BY TWO OR THREE PHASE CURRENTS. SELECT REPLY CODE 10AE08 ACZEA /D/ 12QUANTITY,LINE,SERVICE,PRIMARY WINDING PRIMARY WINDING SERVICE LINE QUANTITY THE NUMBER OF SERVICE LINES PROVIDED FOR ELECTRICAL CONNECTIONS TO THE PRIMARY/INPUT/WINDINGS. 1A MODE REPLY 0 ACZFJ 10POWER RATING,TRANSFORMER,MAXIMUM MAXIMUM TRANSFORMER POWER RATING THE MAXIMUM AMOUNT OF POWER FOR WHICH THE TRANSFORMER IS RATED. 1D AND 1B MODE REPLY11AC33 ACZGB /D/ 10FACTOR IN PERCENT,POWER POWER FACTOR IN PERCENT THE RATIO OF THE ACTUAL MEASURED POWER OF A PRIMARY WINDING TO THE APPARENT POWER IN THE SECONDARY WINDING AT A SPECIFIED LOAD,EXPRESSED IN PERCENT. 1B MODE REPLY 0 ACZHA 10RATIO,TURN,PRIMARY TO SECONDARY PRIMARY TO SECONDARY TURN RATIO THE RATIO OF THE NUMBER OF TURNS IN A PRIMARY WINDING TO THE NUMBER OF TURNS IN THE SECONDARY WINDING OF A TRANSFORMER. 1A MODE REPLY 0 ACZJJ /D/ 10AMPLITUDE,PULSE,PEAK PEAK PULSE AMPLITUDE THE MAXIMUM ABSOLUTE PEAK VALUE OF THE PULSE,EXCLUDING UNWANTED PORTIONS SUCH AS SPIKES. 1D AND 1B MODE REPLY11AB63 ACZKB /D/ 10DURATION IN MICROSECONDS,PULSE PULSE DURATION IN MICROSECONDS THE TIME INTERVAL BETWEEN THE 50 PERCENT AMPLITUDE POINTS IN RELATIONSHIP TO THE PEAK PULSE AMPLITUDE,EXPRESSED IN MICROSECONDS. 1B MODE REPLY 0 ACZLB /D/ 10TIME IN MICROSECONDS,RISE,PULSE PULSE RISE TIME IN MICROSECONDS THE LENGTH OF TIME IT TAKES THE LEADING EDGE OF THE PULSE TO RISE FROM 10 PERCENT TO 90 PERCENT OF ITS PEAK PULSE AMPLITUDE,EXPRESSED IN MICROSECONDS. 1B MODE REPLY 0 ACZMB /D/ 10TIME IN MICROSECONDS,DECAY,PULSE PULSE DECAY TIME IN MICROSECONDS THE LENGTH OF TIME IT TAKES THE TRAILING EDGE OF THE PULSE TO FALL FROM 90 PERCENT TO 10 PERCENT OF ITS PEAK PULSE AMPLITUDE,EXPRESSED IN MICROSECONDS. 1B MODE REPLY 0 ACZNJ 10REPETITION RATE,PULSE PULSE REPETITION RATE THE AVERAGE RATE AT WHICH THE PULSES RECUR WITHIN A SPECIFIED TIME INTERVAL. 1D AND 1B MODE REPLY11AC32 ACZPD 18TYPE,FORM,COIL COIL FORM TYPE INDICATES THE TYPE OF SUPPORT ON WHICH THE COIL IS WOUND. SELECT REPLY CODE 10AC12 ACZQB 10DISSIPATION RATING IN WATTS,POWER,RESISTOR RESISTOR POWER DISSIPATION RATING IN WATTS THE MAXIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY A RESISTOR,EXPRESSED IN WATTS. 1B MODE REPLY 0 ACZRD 19CONSTRUCTION,CORE CORE CONSTRUCTION THE DESIGNATION DESCRIBING THE METHOD USED IN FORMING THE CORE. SELECT REPLY CODE 10AC13 ACZSD /D/ 11METHOD,DEVICE,ADJUSTMENT ADJUSTMENT DEVICE METHOD THE INTEGRAL MEANS PROVIDED TO ADJUST AN ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. SELECT REPLY CODE 10AC14 ACZTA 12QUANTITY,DEVICE,ADJUSTMENT ADJUSTMENT DEVICE QUANTITY THE NUMBER OF FIXED OR ADJUSTABLE FACILITIES PROVIDED TO ADJUST AN ITEM. 1A MODE REPLY 0 ACZUD 18TYPE,DRIVE,DEVICE,ADJUSTMENT ADJUSTMENT DEVICE DRIVE TYPE INDICATES THE TYPE OF DRIVE PROVIDED FOR THE ADJUSTMENT DEVICE. SELECT REPLY CODE 10AE10 ACZVD 19MEDIUM,COOLING COOLING MEDIUM THE COOLING MEDIUM USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE ITEM. SELECT REPLY CODE 10AB75 ACZWD /D/ 18TYPE,COOLING COOLING TYPE INDICATES THE TYPE OF FEATURE INCORPORATED ON THE ITEM TO PROVIDE AMPLE RADIATING SURFACE FOR THE DISSIPATION OF HEAT. SELECT REPLY CODE 10AC17 ACZXD 11METHOD,SHIELDING,WINDING WINDING SHIELDING METHOD THE MEANS BY WHICH A PROTECTIVE METAL SCREEN,PLATE,OR INCLOSURE IS PLACED AROUND OR BETWEEN THE WINDINGS OF AN ITEM TO PREVENT ELECTROSTATIC OR MAGNETIC COUPLING. SELECT REPLY CODE 10AC18 ACZYD /D/ 18TYPE,TERMINAL,DUMMY DUMMY TERMINAL TYPE INDICATES THE TYPE OF DUMMY TERMINAL INCLUDED ON THE ITEM. SELECT REPLY CODE 10AA58 ADABD /D/ 09MATERIAL,DEVICE,ADJUSTMENT ADJUSTMENT DEVICE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ADJUSTMENT DEVICE IS FABRICATED. SELECT REPLY CODE 10AD09 ADACA /D/ 19CODE,AMMUNITION,DEPARTMENT,ARMY ARMY DEPARTMENT AMMUNITION CODE A SEVEN(7) OR EIGHT(8) CHARACTER SIGNIFICANT NUMBER DIVIDED INTO TWO PARTS BY A HYPHEN ASSIGNED TO ITEMS OF SUPPLY IN NSG(FSG) 13 AND 14 WHICH HAVE AN EXPLOSIVE CONTENT. 1A MODE REPLY 0 ADADG /D/ 19SPEC/STD,SURFACE TREATMENT SURFACE TREATMENT SPEC/STD THE DOCUMENT CONTROLLING THE COMPOSITION AND/OR PERFORMANCE CAPABILITIES OF A SURFACE TREATMENT. FULL TEXT WRITE-IN 0 ADAEA /D/ 12QUANTITY,HOLE/STUD,MOUNTING MOUNTING HOLE/STUD QUANTITY THE NUMBER OF HOLES/SLOTS OR STUDS PROVIDED FOR ATTACHING THE ITEM TO A SURFACE. 1A MODE REPLY 0 ADAFJ A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,HOLE/STUD,MOUNTING MOUNTING HOLE/STUD THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE MOUNTING HOLE OR STUD THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AC21 ADAGJ 04LENGTH,STUD,MOUNTING MOUNTING STUD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING STUD,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADAHJ /D/ 04DISTANCE BETWEEN MOUNTING HOLES/STUDS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES/STUDS THE MEASURED DISTANCE BETWEEN THE MOUNTING HOLE AND/OR STUD CENTERS. 2D AND 1B MODE REPLY21AA051AC20 ADAJJ 04LENGTH,ACCOMMODATION,BODY MOUNTING HOLE BODY MOUNTING HOLE ACCOMMODATION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADAKJ 04WIDTH,ACCOMMODATION,BODY MOUNTING HOLE BODY MOUNTING HOLE ACCOMMODATION WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADALJ 04DIAMETER,ACCOMMODATION,BODY MOUNTING HOLE BODY MOUNTING HOLE ACCOMMODATION DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADAMA 12QUANTITY,SPOUT,FILLER FILLER SPOUT QUANTITY THE NUMBER OF FILLER SPOUTS FURNISHED. 1A MODE REPLY 0 ADAND 18TYPE,SPRAY,LUBRICATION LUBRICATION SPRAY TYPE INDICATES THE TYPE OF OIL SPRAY EMITTED BY THE LUBRICATING DEVICE INTO A COMPRESSED AIR SYSTEM. SELECT REPLY CODE 10AL82 ADAPJ 04LENGTH,BUSHING,MOUNTING MOUNTING BUSHING LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADAQJ 04LENGTH,BODY BODY LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BODY,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADARJ 04DIAMETER,OUTSIDE,BODY BODY OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADASJ 04DIAMETER,INSIDE,BODY BODY INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BODY,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADATJ 04WIDTH,BODY BODY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BODY,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ADAUJ 04HEIGHT,BODY BODY HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BODY,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 ADAVJ 04DIAMETER,OVERALL OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE. 2D AND 1B MODE REPLY21AA051AC20 ADAWD /D/ 07DEVICE,SHORT CIRCUITING,SECONDARY WINDING SECONDARY WINDING SHORT CIRCUITING DEVICE AN INDICATION OF WHETHER OR NOT A DEVICE IS INCLUDED FOR SHORT CIRCUITING THE SECONDARY WINDING. SELECT REPLY CODE 10AA49 ADAXD /D/ 11METHOD,CONTROL,VOLTAGE VOLTAGE CONTROL METHOD THE METHOD OF DRIVE PROVIDED FOR CONTROLLING THE VOLTAGE. SELECT REPLY CODE 10AE13 ADAYA 12ACCOMMODATED,QUANTITY,WHEEL WHEEL QUANTITY ACCOMMODATED THE NUMBER OF WHEELS WHICH THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 ADAZJ 04DIAMETER,THRU-HOLE THRU-HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A THRU-HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADBAJ 04HEIGHT,BARREL BARREL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ADBBJ 04DISTANCE FROM CENTERLINE OF THREADED HOLE TO END OF NUT DISTANCE FROM CENTERLINE OF THREADED HOLE TO END OF NUT NONE. 2D AND 1B MODE REPLY21AA051AC20 ADBCJ /D/ 04THICKNESS,PORTION,FLATTED FLATTED PORTION THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADBDJ 04DEPTH,COUNTERSINK COUNTERSINK DEPTH THE MEASUREMENT OF THE PROCESS USED TO ENLARGE PART OF A HOLE,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 ADBEJ 04WIDTH,PILOT PILOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADBFJ /D/ 04DISTANCE FROM CENTER,FLOATING FLOATING DISTANCE FROM CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADBGJ 04THICKNESS,NUT NUT THICKNESS A MEASUREMENT BETWEEN THE OPPOSITE FLAT SURFACES OF THE NUT,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADBHJ 04WIDTH,POINT,DRIVE DRIVE POINT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADBJJ 04THICKNESS,UNDERCUT UNDERCUT THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADBKJ 04WIDTH,KNURL KNURL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADBLJ 04LENGTH,END,SMALL SMALL END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADBMA 12QUANTITY,POINT,DRIVE DRIVE POINT QUANTITY NONE. 1A MODE REPLY 0 ADBNJ 04DIAMETER,BOSS BOSS DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOSS,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADBPJ 04THICKNESS,BOSS BOSS THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADBQJ 04DIAMETER,OUTSIDE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ADBRJ 04DISTANCE FROM BASE TO CENTER OF APERTURE DISTANCE FROM BASE TO CENTER OF APERTURE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADBSJ 04DIAMETER,INSIDE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ITEM,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ADBTD 11METHOD,LANDING SHOCK ABSORPTION AND DISSIPATION LANDING SHOCK ABSORPTION AND DISSIPATION METHOD THE MEANS BY WHICH THE ITEM CUSHIONS THE IMPACT UPON LANDING. SELECT REPLY CODE 10AM39 ADBUD 11METHOD,GEAR EXTENSION AND RETRACTION GEAR EXTENSION AND RETRACTION METHOD THE MEANS BY WHICH THE ITEM IS RAISED OR LOWERED. SELECT REPLY CODE 10AC58 ADBVD 18TYPE FOR WHICH DESIGNED,PUMP PUMP TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF PUMP FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK95 ADBWA /D/ 19ACTIVITY,CONTROL,DESIGN,GOVERNOR GOVERNOR DESIGN CONTROL ACTIVITY THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE GOVERNMENT AGENCY,INDUSTRIAL ORGANIZATION,OR OTHER ENTITY,WHICH CONTROLS THE DESIGN OF THE GOVERNOR. 1A MODE REPLY 0 ADBXA /D/ 19MODEL NUMBER FOR WHICH DESIGNED,GOVERNOR GOVERNOR MODEL NUMBER FOR WHICH DESIGNED THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE GOVERNOR FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 ADBYL 16STYLE,END,CONNECTING,ROD,LINK LINK ROD CONNECTING END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LINK ROD CONNECTING END. 1L MODE REPLY 0 ADBZL 16STYLE,END,SOCKET,PISTON PISTON SOCKET END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PISTON SOCKET END. 1L MODE REPLY 0 ADCAD 18TYPE ACCOMMODATED,FITTING,VALVE VALVE FITTING TYPE ACCOMMODATED INDICATES THE TYPE OF FITTING THE VALVE WILL ACCOMMODATE. SELECT REPLY CODE 10AK84 ADCBD 18TYPE,NOZZLE NOZZLE TYPE INDICATES THE DESIGN TYPE OF THE NOZZLE. SELECT REPLY CODE 10AK54 ADCCD /D/ 19MEDIA FOR WHICH NOZZLE SPOUT IS DESIGNED MEDIA FOR WHICH NOZZLE SPOUT IS DESIGNED THE TYPE OF SERVICE FOR WHICH THE NOZZLE SPOUT IS DESIGNED TO BE USED. SELECT REPLY CODE 10AN91 ADCDJ 04SIZE,PORT,DRAIN DRAIN PORT SIZE DESIGNATES THE SIZE OF THE DRAIN PORT. 1D AND 1B MODE REPLY11AA05 ADCEJ 04LENGTH,DEVELOPED,NOMINAL NOMINAL DEVELOPED LENGTH A NOMINAL DEVELOPED MEASUREMENT OF THE LONGEST DIMENSION OF THE ITEM INCLUDING ANY BENDS AND ANGLES, IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 ADCFJ /D/ 04LENGTH,BEND BEND LENGTH A MEASUREMENT OF THE DEVELOPED LENGTH OF THE TUBE WITH STRETCH DEDUCTED AT BEND ARCS. BEND LENGTH IS ALSO MINIMUM ORDERED LENGTH. 1D AND 1B MODE REPLY11AA05 ADCGJ /D/ 04LENGTH,PLATE,ANGLE ANGLE PLATE LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CONVERGENCE OF THE FIRST AND SECOND SURFACES OF THEANGLE PLATE. 2D AND 1B MODE REPLY21AA051AC20 ADCHJ /D/ 04WIDTH,PLATE,ANGLE ANGLE PLATE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH ALONG THE FIRST SURFACE OF THE ANGLE PLATE, IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ADCJJ /D/ 04HEIGHT,PLATE,ANGLE ANGLE PLATE HEIGHT A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH ALONG THE SECOND SURFACE OF THE ANGLE PLATE, IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 ADCKJ /D/ 04THICKNESS,PLATE,ANGLE ANGLE PLATE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE ANGLE PLATE, IN DISTINCTION FROM THE LENGTH, WIDTH OR HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 ADCLJ 04DIAMETER,NECK NECK DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A NECK,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADCMJ 04DISTANCE FROM SPHERICAL HEAD CENTERLINE TO HEAD END DISTANCE FROM SPHERICAL HEAD CENTERLINE TO HEAD END NONE. 2D AND 1B MODE REPLY21AA051AC20 ADCNJ /D/ 04DISTANCE FROM FLAT OF HEAD TO HEAD END DISTANCE FROM FLAT OF HEAD TO HEAD END NONE. 2D AND 1B MODE REPLY21AA051AC20 ADCPJ /D/ 04DEPTH,HOLE,PLAIN PLAIN HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADCQJ 04DIAMETER,HOLE,PLAIN PLAIN HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PLAIN HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADCRJ 04LENGTH,SHANK,PLAIN PLAIN SHANK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADCSJ 04DIAMETER,SHANK,PLAIN PLAIN SHANK DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SHANK,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADCTJ 04DISTANCE FROM SERRATED PORTION TO NUT END DISTANCE FROM SERRATED PORTION TO NUT END NONE. 2D AND 1B MODE REPLY21AA051AC20 ADCUJ 04DISTANCE FROM SERRATED PORTION TO STUD END DISTANCE FROM SERRATED PORTION TO STUD END NONE. 2D AND 1B MODE REPLY21AA051AC20 ADCVJ 04DISTANCE FROM SHOULDER PORTION TO NUT END DISTANCE FROM SHOULDER PORTION TO NUT END NONE. 2D AND 1B MODE REPLY21AA051AC20 ADCWJ /D/ 04LENGTH FROM SHOULDER PORTION TO STUD END LENGTH FROM SHOULDER PORTION TO STUD END NONE. 2D AND 1B MODE REPLY21AA051AC20 ADCXJ 04DISTANCE FROM SERRATED PORTION TO END OF STUD THREAD DISTANCE FROM SERRATED PORTION TO END OF STUD THREAD NONE. 2D AND 1B MODE REPLY21AA051AC20 ADCYJ 04LENGTH FROM SERRATED PORTION THROUGH SHOULDER LENGTH FROM SERRATED PORTION THROUGH SHOULDER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADCZJ 04LENGTH OF RECESSED PORTION OF SHANK LENGTH OF RECESSED PORTION OF SHANK NONE. 2D AND 1B MODE REPLY21AA051AC20 ADDAJ 04DIAMETER OF RECESSED PORTION OF SHANK DIAMETER OF RECESSED PORTION OF SHANK NONE. 2D AND 1B MODE REPLY21AA051AC20 ADDBJ 04LENGTH,SHANK,NUT END NUT END SHANK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADDCJ 04LENGTH EXCLUDING WRENCHING PORTION,SHANK SHANK LENGTH EXCLUDING WRENCHING PORTION NONE. 2D AND 1B MODE REPLY21AA051AC20 ADDDJ 04DIAMETER,END,UNTHREADED UNTHREADED END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE UNTHREADED END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADDEJ 04LENGTH,END,UNTHREADED UNTHREADED END LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE UNTHREADED END. 2D AND 1B MODE REPLY21AA051AC20 ADDFJ 04LENGTH EXCLUDING FLUXED WELDING TIP LENGTH EXCLUDING FLUXED WELDING TIP NONE. 2D AND 1B MODE REPLY21AA051AC20 ADDGJ 04LENGTH,LEG,WELD WELD LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADDHJ 04DISTANCE FROM SHOULDER TO PERIPHERY OF WELD LEG DISTANCE FROM SHOULDER TO PERIPHERY OF WELD LEG NONE. 2D AND 1B MODE REPLY21AA051AC20 ADDJJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,END,NUT NUT END THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE FOR A NUT END. 1D AND 1A MODE REPLY12AC21 ADDKA /D/ 13THREAD CLASS,END,NUT NUT END THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREADED NUT END. 1A MODE REPLY 0 ADDLJ /D/T13THREAD PITCH DIAMETERS,END,NUT NUT END THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 ADDMD /D/ 13THREAD DIRECTION,END,NUT NUT END THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ADDNJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,END,STUD STUD END THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE FOR THE STUD END. 1D AND 1A MODE REPLY12AC21 ADDPA /D/ 13THREAD CLASS,END,STUD STUD END THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD ON THE STUD END. 1A MODE REPLY 0 ADDQJ /D/T13THREAD PITCH DIAMETERS,END,STUD STUD END THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD ON THE STUD END. 1D AND 1F MODE REPLY11AA05 ADDRD /D/ 13THREAD DIRECTION,END,STUD STUD END THREAD DIRECTION THE DIRECTION OF THE STUD END THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ADDSJ /D/ 13THREAD LENGTH,END,NUT NUT END THREAD LENGTH A MEASUREMENT OF THE EXTENT OF THE NUT END THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS. 2D AND 1B MODE REPLY21AA051AC20 ADDTJ /D/ 13THREAD LENGTH,END,STUD STUD END THREAD LENGTH A MEASUREMENT OF THE EXTENT OF COMPLETE /FULL/ THREADS ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS ON THE STUD END. 2D AND 1B MODE REPLY21AA051AC20 ADDUJ 04DISTANCE FROM COTTER PIN HOLE CENTERLINE TO NUT END DISTANCE FROM COTTER PIN HOLE CENTERLINE TO NUT END THE DISTANCE,MEASURED ALONG A STRAIGHT LINE PARALLEL TO THE LONGITUDINAL AXIS,FROM THE CENTER OF THE COTTER PIN HOLE TO THE NUT END OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ADDVJ 04DIAMETER,HOLE,COTTER PIN COTTER PIN HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COTTER PIN HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADDWA 12QUANTITY,SERRATION SERRATION QUANTITY THE NUMBER OF SERRATIONS ON THE ITEM. 1A MODE REPLY 0 ADDXB 04ANGLE IN DEG,INCLUDED,SERRATION SERRATION INCLUDED ANGLE IN DEG THE DIFFERENCE IN DIRECTION BETWEEN THE TWO SIDES OF ADJOINING SERRATIONS,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ADDYD /D/ 07HEAT SHIELD FEATURE HEAT SHIELD FEATURE AN INDICATION AS TO WHETHER OR NOT A HEAT SHIELD IS INCLUDED ON THE ITEM FOR PROTECTION FROM THE HEAT OF THE WELDING ARC. SELECT REPLY CODE 10AA49 ADDZD /D/ 07FEATURE,FLUX FLUX FEATURE AN INDICATION OF WHETHER OR NOT A SURFACE COATING IS INCLUDED ON THE ITEM TO FACILITATE WELDING BY PREVENTING OXIDATION IN THE PROCESS. SELECT REPLY CODE 10AA49 ADEAJ 04HEIGHT,NUT NUT HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ADEBJ 04THICKNESS,PLATE PLATE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A PLATE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADECJ 04WIDTH,PLATE PLATE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A PLATE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ADEDJ 04WIDTH,NUT NUT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADEEJ 04THICKNESS,PANEL PANEL THICKNESS AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF A PANEL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADEFJ 04DISTANCE FROM CENTER OF APERATURE TO END DISTANCE FROM CENTER OF APERATURE TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 ADEGJ 04DISTANCE,CENTER TO CENTER,APERTURE APERTURE CENTER TO CENTER DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADEHA 12QUANTITY,NOTCH,GRIPPING GRIPPING NOTCH QUANTITY NONE. 1A MODE REPLY 0 ADEJA /D/ 12QUANTITY,SLIT SLIT QUANTITY THE NUMBER OF SLITS PROVIDED. 1A MODE REPLY 0 ADEKJ 04DISTANCE,CUTOFF EDGE TO CENTER CUTOFF EDGE TO CENTER DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADELJ 04HEIGHT,WING WING HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A WING,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 ADEMJ 04THICKNESS,WASHER WASHER THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADENJ 04THICKNESS,BODY,EYE EYE BODY THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADEPJ 04WIDTH,HOLE HOLE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A HOLE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ADEQJ 04HEIGHT,HOLE HOLE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ADERL 16STYLE,MOUNTING MOUNTING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE MOUNTING. 1L MODE REPLY 0 ADESB /D/ 04SPACING IN DEG,ANGULAR,MOUNTING HOLE MOUNTING HOLE ANGULAR SPACING IN DEG NONE. 1B MODE REPLY 0 ADETB /D/ 04SPACING IN DEG,ANGULAR,NUT NUT ANGULAR SPACING IN DEG NONE. 1B MODE REPLY 0 ADEUJ /D/ 04DISTANCE,NUT CENTER TO MOUNTING HOLE CENTER NUT CENTER TO MOUNTING HOLE CENTER DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADEVJ 04DIAMETER,OUTSIDE,RING RING OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE RING,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADEWJ 10SPACING,NUT,CENTER TO CENTER CENTER TO CENTER NUT SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 ADEXJ 04SPACING ALONG LENGTH,NUT,CENTER TO CENTER CENTER TO CENTER NUT SPACING ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADEYJ /D/T10RANGE,GRIP,NUT NUT GRIP RANGE THE AREA BETWEEN THE MAXIMUM AND MINIMUM THICKNESS OF MATERIAL IN WHICH A SPECIFIC BLIND RIVET NUT CAN BE PROPERLY INSTALLED. 1D AND 1F MODE REPLY11AA05 ADEZJ /D/ 04DISTANCE BETWEEN MOUNTING HOLES ALONG LENGTH,CENTER TO CENTER,FIRST SURFACE FIRST SURFACE CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES ALONG LENGTH THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING HOLE AND THE CENTER OF THE ADJACENT MOUNTING HOLE ALONG THE LENGTH OF THE FIRST SURFACE. 2D AND 1B MODE REPLY21AA051AC20 ADFAD /D/ 18TYPE,SURFACE,BEARING BEARING SURFACE TYPE INDICATES THE TYPE OF BEARING SURFACE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. SELECT REPLY CODE 10AC35 ADFBB /D/ 10FINISH IN MICROINCHES,SURFACE,BEARING BEARING SURFACE FINISH IN MICROINCHES THE FINISH PRODUCED ON THE BEARING SURFACE BY MACHINING,GRINDING,OR POLISHING,EXPRESSED IN MICROINCHES. 1B MODE REPLY 0 ADFCD /D/ 07FEATURE,REMOVABILITY,NUT NUT REMOVABILITY FEATURE INDICATES WHETHER OR NOT THE DESIGN FEATURE PERMITTING REPLACEMENT OF INDIVIDUAL NUTS IS INCLUDED. SELECT REPLY CODE 10AA49 ADFDA 19CODE,MANUFACTURER,REMOVABLE NUT REMOVABLE NUT MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE REMOVABLE NUT. 1A MODE REPLY 0 ADFEL 16STYLE,CHANNEL CHANNEL STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CHANNEL. 1L MODE REPLY 0 ADFFJ 04HEIGHT,OVERALL,ASSEMBLY ASSEMBLY OVERALL HEIGHT THE OVERALL DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE ASSEMBLY. 2D AND 1B MODE REPLY21AA051AC20 ADFGJ 04HEIGHT,CHANNEL CHANNEL HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE CHANNEL,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 ADFHJ 10SPACING,NUT NUT SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 ADFJD /D/ 02DESIGN,FLOATING FLOATING DESIGN THE TYPE OF DESIGN WHICH PERMITS THE ITEM TO MOVE IN EITHER A LINEAR OR ANGULAR DIRECTION OR BOTH. SELECT REPLY CODE 10AA89 ADFKJ 04DEPTH,COUNTERBORE,NUT NUT COUNTERBORE DEPTH THE MEASUREMENT OF THE ENLARGED PORTION ADJACENT TO THE THREADED PORTION OF A NUT,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 ADFLJ 04DIAMETER,PILOT,HEAD HEAD PILOT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADFMB /D/ 04ANGLE IN DEG,COUNTERSINK,HEAD HEAD COUNTERSINK ANGLE IN DEG NONE. 1B MODE REPLY 0 ADFND 18TYPE,END,SHANK SHANK END TYPE INDICATES THE TYPE OF END INCLUDED ON THE SHANK. SELECT REPLY CODE 10AC59 ADFPD 19PROVISION,MOUNTING,NUT NUT MOUNTING PROVISION THE MEANS BY WHICH THE NUT IS MOUNTED. SELECT REPLY CODE 10AC37 ADFQB 04ANGLE IN DEG,HOLE,MOUNTING,COUNTERSUNK COUNTERSUNK MOUNTING HOLE ANGLE IN DEG THE INCLUDED ANGLE OF THE MOUNTING HOLE COUNTERSINK,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ADFRD /D/ 08LOCATION,PROVISION,MOUNTING MOUNTING PROVISION LOCATION THE SIDE OF THE PLATE THAT THE COUNTERSINK OR WELDING PROJECTIONS ARE LOCATED. SELECT REPLY CODE 10AE46 ADFSA 12QUANTITY,PRONG,GRIPPING GRIPPING PRONG QUANTITY THE NUMBER OF GRIPPING PRONGS INCLUDED ON THE ITEM. 1A MODE REPLY 0 ADFTJ 04LENGTH,PRONG,GRIPPING GRIPPING PRONG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION FROM THE END OF THE GRIPPING PRONG TO THE BASE OF THE NUT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADFUL 16STYLE,ARRANGEMENT,MOUNTING HOLE MOUNTING HOLE ARRANGEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE MOUNTING HOLE(S). 1L MODE REPLY 0 ADFVJ 04DISTANCE FROM MOUNTING HOLE CENTER TO BASE DISTANCE FROM MOUNTING HOLE CENTER TO BASE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADFWJ 04DISTANCE FROM APERTURE CENTER TO MOUNTING HOLE CENTER DISTANCE FROM APERTURE CENTER TO MOUNTING HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADFXJ 04DISTANCE BETWEEN MOUNTING HOLES ALONG WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES ALONG WIDTH A MEASUREMENT OF THE CENTER TO CENTER DISTANCE BETWEEN THE MOUNTING HOLES ALONG THE WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADFYJ 04DISTANCE BETWEEN MOUNTING HOLES ALONG LENGTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES ALONG LENGTH A MEASUREMENT OF THE CENTER TO CENTER DISTANCE BETWEEN THE MOUNTING HOLES ALONG THE LENGTH. 2D AND 1B MODE REPLY21AA051AC20 ADFZD /D/ 07COLLAR,REMOVABLE REMOVABLE COLLAR INDICATES WHETHER OR NOT THE REMOVABLE COLLAR BETWEEN THE BALL OR CONE SEAT AND DRIVE IS INCLUDED. SELECT REPLY CODE 10AA49 ADGAJ 04DIAMETER,OUTSIDE,OVERALL OVERALL OUTSIDE DIAMETER THE OVERALL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADGBJ 04DIAMETER,COUNTERBORE COUNTERBORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COUNTERBORE PORTION OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ADGCJ 04DEPTH,COUNTERBORE COUNTERBORE DEPTH THE DEPTH OF THE COUNTERBORE PORTION OF A HOLE. 1D AND 1B MODE REPLY11AA05 ADGDJ /D/ 04DIAMETER,BORE BORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BORE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ADGEJ 04LENGTH,BORE BORE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A BORE. 2D AND 1B MODE REPLY21AA051AC20 ADGFJ 04LENGTH,RECESS,OUTSIDE OUTSIDE RECESS LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADGGJ 04WIDTH,RECESS,OUTSIDE OUTSIDE RECESS WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADGHJ /D/ 04DISTANCE BETWEEN MOUNTING HOLES ALONG LENGTH,CENTER TO CENTER,SECOND SURFACE SECOND SURFACE CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES ALONG LENGTH THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING HOLE AND THE CENTER OF THE ADJACENT MOUNTING HOLE ALONG THE LENGTH OF THE SECOND SURFACE. 2D AND 1B MODE REPLY21AA051AC20 ADGJB /D/ 04ANGLE IN DEG,SLOT,FIRST FIRST SLOT ANGLE IN DEG NONE. 1B MODE REPLY 0 ADGKJ /D/ 04LENGTH,CHAMFER,FIRST PACKING CHAMBER FIRST PACKING CHAMBER CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 ADGLJ /D/ 04DEPTH,CHAMFER,PACKING CHAMBER,FIRST FIRST PACKING CHAMBER CHAMFER DEPTH NONE. REPLACED BY MRC AGHG WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 ADGMB /D/ 04ANGLE IN DEG,CHAMFER,FIRST PACKING CHAMBER FIRST PACKING CHAMBER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 ADGNJ 04LENGTH,CHAMFER,FIRST END FIRST END CHAMFER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CHAMFER AT THE FIRST END. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 ADGPJ 04DEPTH,CHAMFER,FIRST END FIRST END CHAMFER DEPTH A MEASUREMENT FROM THE TOP TO THE BOTTOM OF THE BEVEL ON THE FIRST END. REPLACED BY MRC AGHG WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 ADGQB /D/ 04ANGLE IN DEG,CHAMFER,FIRST END FIRST END CHAMFER ANGLE IN DEG THE ANGLE OF THE BEVEL ON THE FIRST END,EXPRESSED IN DEGREES. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 ADGRJ 04LENGTH,CHAMFER,SECOND END SECOND END CHAMFER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CHAMFER AT THE SECOND END. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 ADGSJ 04DEPTH,CHAMFER,SECOND END SECOND END CHAMFER DEPTH A MEASUREMENT FROM THE TOP TO THE BOTTOM OF THE BEVEL ON THE SECOND END. REPLACED BY MRC AGHG WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 ADGTB /D/ 04ANGLE IN DEG,CHAMFER,SECOND END SECOND END CHAMFER ANGLE IN DEG THE ANGLE OF THE BEVEL ON THE SECOND END,EXPRESSED IN DEGREES. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 ADGUJ /D/ 04DIAMETER,OUTSIDE,TAPER TAPER OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADGVJ 04THREAD RELIEF LENGTH THREAD RELIEF LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADGWJ 04THREAD RELIEF DEPTH THREAD RELIEF DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADGXB /D/ 04SPACING IN DEG,ANGULAR,AIR RELIEF HOLE AIR RELIEF HOLE ANGULAR SPACING IN DEG NONE. 1B MODE REPLY 0 ADGYJ /D/ 04DIAMETER,HOLE,AIR RELIEF AIR RELIEF HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADGZJ 04DISTANCE FROM CENTER OF HOLE TO OUTSIDE EDGE DISTANCE FROM CENTER OF HOLE TO OUTSIDE EDGE THE DISTANCE FROM THE CENTER OF THE HOLE TO THE OUTSIDE EDGE OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ADHAJ /D/ 04WIDTH,MAXIMUM,SAW CUT SAW CUT MAXIMUM WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADHBJ /D/ 04DISTANCE BETWEEN SAFETY WIRE HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SAFETY WIRE HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 ADHCJ /D/ 04DIAMETER,HOLE,SAFETY WIRE SAFETY WIRE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADHDB /D/ 04SPACING IN DEG,ANGULAR,SAFETY WIRE HOLE SAFETY WIRE HOLE ANGULAR SPACING IN DEG NONE. 1B MODE REPLY 0 ADHEJ 04LENGTH,END,MOUNTING MOUNTING END LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADHFJ 04LENGTH,RECESS,INSIDE INSIDE RECESS LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADHGJ 04WIDTH,RECESS,INSIDE INSIDE RECESS WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADHHJ 04LENGTH,HEAD HEAD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A HEAD,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 ADHJJ /D/ 04DISTANCE FROM CENTER OF MOUNTING HOLE TO OUTSIDE EDGE DISTANCE FROM CENTER OF MOUNTING HOLE TO OUTSIDE EDGE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADHKB /D/ 04ANGLE IN DEG,TAPER,OUTSIDE OUTSIDE TAPER ANGLE IN DEG NONE. 1B MODE REPLY 0 ADHLJ 04THICKNESS,DISK DISK THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADHMJ 04DIAMETER,INSIDE,FIRST PACKING CHAMBER FIRST PACKING CHAMBER INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADHNJ 04DIAMETER,INSIDE,SECOND PACKING CHAMBER SECOND PACKING CHAMBER INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADHPJ 04LENGTH,CHAMBER,FIRST PACKING FIRST PACKING CHAMBER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADHQJ 04LENGTH,CHAMBER,SECOND PACKING SECOND PACKING CHAMBER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADHRB 04ANGLE IN DEG,TAPER,COUNTERBORE COUNTERBORE TAPER ANGLE IN DEG NONE. 1B MODE REPLY 0 ADHSJ /D/ 04LENGTH,CHAMFER,SECOND PACKING CHAMBER SECOND PACKING CHAMBER CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 ADHTJ /D/ 04DEPTH,CHAMFER,PACKING CHAMBER,SECOND SECOND PACKING CHAMBER CHAMFER DEPTH NONE. REPLACED BY MRC AGHG WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 ADHUB /D/ 04ANGLE IN DEG,CHAMFER,SECOND PACKING CHAMBER SECOND PACKING CHAMBER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 ADHVJ 04DISTANCE BETWEEN MOUNTING HOLES ALONG LENGTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES ALONG LENGTH A MEASUREMENT OF THE CENTER TO CENTER DISTANCE BETWEEN THE MOUNTING HOLES ALONG THE LENGTH. 1D AND 1B MODE REPLY11AA05 ADHWJ 04DISTANCE BETWEEN MOUNTING HOLES ALONG WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES ALONG WIDTH A MEASUREMENT OF THE CENTER TO CENTER DISTANCE BETWEEN THE MOUNTING HOLES ALONG THE WIDTH. 1D AND 1B MODE REPLY11AA05 ADHXJ 04DISTANCE FROM MOUNTING HOLE CENTER TO BASE EDGE ALONG LENGTH DISTANCE FROM MOUNTING HOLE CENTER TO BASE EDGE ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADHYJ 04DISTANCE FROM MOUNTING HOLE CENTER TO BASE EDGE ALONG WIDTH DISTANCE FROM MOUNTING HOLE CENTER TO BASE EDGE ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADHZJ 04DIAMETER,OUTSIDE,MOUNTING MOUNTING OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MOUNTING,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADJAJ 04DISTANCE FROM CENTER OF PACKING CHAMBER END TO EDGE OF MOUNTING END DISTANCE FROM CENTER OF PACKING CHAMBER END TO EDGE OF MOUNTING END NONE. 2D AND 1B MODE REPLY21AA051AC20 ADJBJ 04DISTANCE FROM CENTER OF MOUNTING END TO EDGE OF PACKING CHAMBER END DISTANCE FROM CENTER OF MOUNTING END TO EDGE OF PACKING CHAMBER END NONE. 2D AND 1B MODE REPLY21AA051AC20 ADJCJ 04DISTANCE FROM OUTSIDE EDGE OF FIRST PACKING CHAMBER TO EDGE OF MOUNTING FLANGE DISTANCE FROM OUTSIDE EDGE OF FIRST PACKING CHAMBER TO EDGE OF MOUNTING FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADJDJ 04DISTANCE FROM OUTSIDE EDGE OF SECOND PACKING CHAMBER TO EDGE OF MOUNTING FLANGE DISTANCE FROM OUTSIDE EDGE OF SECOND PACKING CHAMBER TO EDGE OF MOUNTING FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADJEA 03DESIGNATION,SIZE,TUBE TUBE SIZE DESIGNATION THE ALPHA AND/OR NUMERIC SIZE DESIGNATION BY WHICH THE TUBE IS IDENTIFIED. 1A MODE REPLY 0 ADJFJ /D/ 04SIZE,PIPE,NOMINAL,FIRST END FIRST END NOMINAL PIPE SIZE THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE. 1D AND 1B MODE REPLY11AA05 ADJGA 12QUANTITY,CHAMBER,PACKING PACKING CHAMBER QUANTITY THE NUMBER OF PACKING CHAMBERS CONTAINED IN THE ITEM. 1A MODE REPLY 0 ADJHD /D/ 11METHOD,MOUNTING MOUNTING METHOD THE MEANS OF ATTACHING THE ITEM. PLEASE USE MRC AXGY IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB89 ADJJA /D/ 12QUANTITY,HOLE,AIR RELIEF AIR RELIEF HOLE QUANTITY THE NUMBER OF AIR RELIEF HOLES PROVIDED. 1A MODE REPLY 0 ADJKA /D/ 12QUANTITY,HOLE,SAFETY WIRE SAFETY WIRE HOLE QUANTITY THE NUMBER OF SAFETY WIRE HOLES PROVIDED ON THE ITEM. 1A MODE REPLY 0 ADJLL 16STYLE,TUBE,CONVEYING,INNER INNER CONVEYING TUBE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE INNER CONVEYING TUBE. 1L MODE REPLY 0 ADJMD /D/ 09MATERIAL,TUBE,INNER CONVEYING INNER CONVEYING TUBE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INNER CONVEYING TUBE IS FABRICATED. SELECT REPLY CODE 10AD09 ADJND /D/ 19CONDITION,SURFACE,INSIDE INSIDE SURFACE CONDITION THE CONDITION OF THE ITEM WITH RESPECT TO THE TEXTURE OF THE INNER SURFACE. SELECT REPLY CODE 10AC67 ADJPD /D/ 19COMPOSITION,LAYER,REINFORCEMENT REINFORCEMENT LAYER COMPOSITION THE MATERIAL AND FORMATION IDENTIFYING THE STRUCTURAL CHARACTERISTIC/S/ OF THE ITEM. SELECT REPLY CODE 10AD14 ADJQJ /D/ 04DIAMETER,OUTSIDE,FIRST END TUBE FIRST END TUBE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADJRD /D/ 02DESIGN,COVER,OUTER OUTER COVER DESIGN THE DESIGN OF THE OUTER COVER. SELECT REPLY CODE 10AC39 ADJSD 01COLOR,EXTERIOR EXTERIOR COLOR THE HUE OR TINT OF THE EXTERIOR OF THE ITEM. SELECT REPLY CODE 10AD06 ADJTJ 04WIDTH,INSIDE INSIDE WIDTH AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ADJUJ 04LENGTH,INSIDE INSIDE LENGTH A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADJVJ 04WIDTH,OUTSIDE OUTSIDE WIDTH AN OUTSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ADJWJ 04LENGTH,OUTSIDE OUTSIDE LENGTH A MEASUREMENT OF THE LONGEST OUTSIDE DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADJXD /D/ 19CONSTRUCTION,FLANGE,FIRST END FIRST END FLANGE CONSTRUCTION THE DESIGN USED IN CONSTRUCTING THE RETAINING PORTION OF THE FLANGE. SELECT REPLY CODE 10AC40 ADJYD /D/ 19CONSTRUCTION,FLANGE,SECOND END SECOND END FLANGE CONSTRUCTION THE DESIGN USED IN CONSTRUCTING THE RETAINING PORTION OF THE FLANGE. SELECT REPLY CODE 10AC40 ADJZJ /D/ 04DIAMETER,OUTSIDE,CLAMP,FIRST END FIRST END CLAMP OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADKAJ /D/ 04DIAMETER,OUTSIDE,CLAMP,SECOND END SECOND END CLAMP OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADKBJ /D/ 04WIDTH,CLAMP,FIRST END FIRST END CLAMP WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADKCJ /D/ 04WIDTH,CLAMP,SECOND END SECOND END CLAMP WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADKDD /D/ 02DESIGN,CONNECTION,FIRST END FIRST END CONNECTION DESIGN THE PHYSICAL CONFIGURATION OF THE OUTSIDE OF THE PRINCIPAL PART OF THE END CONNECTION. SELECT REPLY CODE 10AC41 ADKED /D/ 02DESIGN,CONNECTION,SECOND END SECOND END CONNECTION DESIGN THE PHYSICAL CONFIGURATION OF THE OUTSIDE OF THE PRINCIPAL PART OF THE END CONNECTION. SELECT REPLY CODE 10AC41 ADKFB /D/ 04ANGLE IN DEG,FLOW,FIRST END FIRST END FLOW ANGLE IN DEG THE ANGLE THAT THE END FLOW IS TURNED FROM THE STRAIGHT FLOW,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ADKGB /D/ 04ANGLE IN DEG,FLOW,SECOND END SECOND END FLOW ANGLE IN DEG THE ANGLE THAT THE END FLOW IS TURNED FROM THE STRAIGHT FLOW,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ADKHD /D/ 07CAPABILITY,ACTION,FIRST END SWIVEL FIRST END SWIVEL ACTION CAPABILITY INDICATES WHETHER OR NOT AN ITEM HAS THE CAPABILITY TO ROTATE AND ALSO MAINTAIN ITS INTENDED FUNCTION. SELECT REPLY CODE 10AA89 ADKJD /D/ 07CAPABILITY,ACTION,SECOND END SWIVEL SECOND END SWIVEL ACTION CAPABILITY INDICATES WHETHER OR NOT AN ITEM HAS THE CAPABILITY TO ROTATE AND ALSO MAINTAIN ITS INTENDED FUNCTION. SELECT REPLY CODE 10AA89 ADKKD /D/ 18TYPE,FITTING/COMPONENT,FIRST END FIRST END FITTING/COMPONENT TYPE THE COMPLETE FITTING OR COMPONENT PART/S/ USED TO MAKE UP THE COMPLETE FITTING. SELECT REPLY CODE 10AC42 ADKLD /D/ 09MATERIAL,FITTING/COMPONENT,FIRST END FIRST END FITTING/COMPONENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ITEM IS FABRICATED. SELECT REPLY CODE 10AD09 ADKMD /D/ 17SURFACE TREATMENT,FITTING/COMPONENT,FIRST END FIRST END FITTING/COMPONENT SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A SURFACE. SELECT REPLY CODE 10AD09 ADKND /D/ 18TYPE,FITTING/COMPONENT,SECOND END SECOND END FITTING/COMPONENT TYPE THE COMPLETE FITTING OR COMPONENT PART/S/ USED TO MAKE UP THE COMPLETE FITTING. SELECT REPLY CODE 10AC42 ADKPD /D/ 09MATERIAL,FITTING/COMPONENT,SECOND END SECOND END FITTING/COMPONENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ITEM IS FABRICATED. SELECT REPLY CODE 10AD09 ADKQD /D/ 17SURFACE TREATMENT,FITTING/COMPONENT,SECOND END SECOND END FITTING/COMPONENT SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A SURFACE. SELECT REPLY CODE 10AD09 ADKRJ 04SIZE,PIPE,NOMINAL,SECOND END SECOND END NOMINAL PIPE SIZE THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE. 1D AND 1B MODE REPLY11AA05 ADKSJ /D/ 04DIAMETER,OUTSIDE,SECOND END TUBE SECOND END TUBE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADKTJ /D/ 10RESISTANCE AT 25 DEG CELSIUS,POWER,ZERO ZERO POWER RESISTANCE AT 25 DEG CELSIUS THE DIRECT CURRENT RESISTANCE VALUE MEASURED AT 25 DEGREE CELSIUS WITH A POWER DISSIPATION LOW ENOUGH THAT ANY FURTHER DECREASE IN POWER WILL RESULT IN NOT MORE THAN 0.1 PERCENT CHANGE IN RESISTANCE. 1D AND 1B MODE REPLY11AA57 ADKUF /D/T10TOLERANCE IN PERCENT AT 25 DEG CELSIUS,RESISTANCE,ZERO POWER ZERO POWER RESISTANCE TOLERANCE IN PERCENT AT 25 DEG CELSIUS THE LIMITS OF PERMISSIBLE VARIATION IN THE ELECTRICAL RESISTANCE VALUE OF AN ITEM FROM ITS RATED ZERO POWER RESISTANCE,EXPRESSED IN PERCENT AT 25 DEGREES CELSIUS. 1F MODE REPLY 0 ADKVJ /D/ 04SIZE,NOMINAL,QUICK DISCONNECT,FIRST END FIRST END QUICK DISCONNECT NOMINAL SIZE THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL SIZE OF THE QUICK DISCONNECT. 1D AND 1B MODE REPLY11AA05 ADKWJ 04SIZE,NOMINAL,QUICK DISCONNECT,SECOND END SECOND END QUICK DISCONNECT NOMINAL SIZE THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL SIZE OF THE QUICK DISCONNECT. 1D AND 1B MODE REPLY11AA05 ADKXB 04ANGLE BETWEEN RIGID ELBOW FITTINGS IN DEG ANGLE BETWEEN RIGID ELBOW FITTINGS IN DEG THE AMOUNT OF ROTATION IN A COUNTERCLOCKWISE DIRECTION NEEDED TO BRING THE CENTERLINE OF ONE RIGID ELBOW INTO COINCIDENCE WITH THE CENTERLINE OF THE RIGID ELBOW ON THE OPPOSITE END,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ADKYD /D/ 07CAPABILITY,DISCHARGE,ELECTROSTATIC ELECTROSTATIC DISCHARGE CAPABILITY INDICATES WHETHER OR NOT AN ITEM HAS THE ABILITY TO CONDUCT AN ELECTROSTATIC CHARGE FOR THE PURPOSE OF DISCHARGING THROUGH THE END FITTINGS,TO ELIMINATE THE POSSIBILITY OF HOSE FAILURE BECAUSE OF ELECTROSTATIC ARCING THROUGH THE WALL OF THE INNERCORE. SELECT REPLY CODE 10AA89 ADKZJ 10PRESSURE,TEST,HYDROSTATIC HYDROSTATIC TEST PRESSURE A STEADY,UNIFORM,INTERNAL STATIC PRESSURE THAT THE ITEM MUST WITHSTAND WITHOUT LEAKAGE,ABNORMAL DISTORTION,OR DAMAGE. 1D AND 1B MODE REPLY11AB18 ADLAJ 10PRESSURE,TEST,BURST BURST TEST PRESSURE THE MINIMUM INTERNAL PRESSURE,AS DETERMINED BY DESTRUCTION TESTS,AT WHICH THE ITEM CAN BE EXPECTED TO RUPTURE. 1D AND 1B MODE REPLY11AB18 ADLBD /D/ 07FEATURE,SELF-SEALING SELF-SEALING FEATURE AN INDICATION OF WHETHER OR NOT A SELF-SEALING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ADLCD /D/ 07SUPPORT FEATURE,INTERNAL INTERNAL SUPPORT FEATURE INDICATES WHETHER OR NOT AN INTERNAL SUPPORT IS INCLUDED FOR REINFORCEMENT PURPOSES. SELECT REPLY CODE 10AA49 ADLDD /D/ 08LOCATION,SUPPORT,EXTERNAL EXTERNAL SUPPORT LOCATION INDICATES THE LOCATION OF THE EXTERNAL SUPPORT OF AN ITEM. SELECT REPLY CODE 10AE46 ADLEJ 10VACUUM RATING VACUUM RATING THE ULTIMATE MAXIMUM VACUUM,EXPRESSED IN TERMS OF ABSOLUTE PRESSURE,THAT MAY BE PRODUCED BY OR APPLIED TO AN ITEM. 1D AND 1B MODE REPLY11AC43 ADLFJ /D/A19DATA,SPEC/STD,HOSE OR TUBING HOSE OR TUBING SPEC/STD DATA THE SPECIFICATION OR STANDARD /INDUSTRIAL OR GOVERNMENTAL/ THAT SPECIFICALLY COVERS THE CONSTRUCTION OF THE HOSE OR TUBING,EXCLUDING THE END FITTINGS. 1D AND 1A MODE REPLY11AC28 ADLGJ /D/A19SPEC/STD DATA,FITTING,FIRST END FIRST END FITTING SPEC/STD DATA THE SPECIFICATION OR STANDARD /INDUSTRIAL OR GOVERNMENTAL/ THAT SPECIFICALLY COVERS ONE COMPLETE END FITTING. 1D AND 1A MODE REPLY11AC28 ADLHJ /D/A19SPEC/STD DATA,FITTING,SECOND END SECOND END FITTING SPEC/STD DATA THE SPECIFICATION OR STANDARD /INDUSTRIAL OR GOVERNMENTAL/ THAT SPECIFICALLY COVERS ONE COMPLETE END FITTING. 1D AND 1A MODE REPLY11AC28 ADLJJ 04LENGTH,LEG LEG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE LEG,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 ADLKJ 04LENGTH,LEG,FIRST FIRST LEG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FIRST LEG, IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADLLJ 04LENGTH,LEG,SECOND SECOND LEG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SECOND LEG, IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADLMJ /D/ 04LENGTH,LEG,THIRD THIRD LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADLND 11METHOD,DISCONNECT,QUICK QUICK DISCONNECT METHOD THE MEANS BY WHICH MECHANICAL ACTION COMPLETELY ENGAGES OR DISENGAGES A MATING QUICK DISCONNECT PART. SELECT REPLY CODE 10AC44 ADLPJ 04SIZE,NOMINAL,QUICK DISCONNECT QUICK DISCONNECT NOMINAL SIZE THE INDUSTRIAL DESIGNATION OR TERM FOR THE SIZE OF THE QUICK DISCONNECT INTERNAL OR EXTERNAL END. 1D AND 1B MODE REPLY11AA05 ADLQD /D/ 08LOCATION,DISCONNECT,QUICK QUICK DISCONNECT LOCATION INDICATES THE LOCATION OF THE ITEM TO WHICH THE QUICK DISCONNECT END IS ATTACHED. SELECT REPLY CODE 10AE46 ADLRD /D/ 07FEATURE,LOCKING,SAFETY,QUICK DISCONNECT QUICK DISCONNECT SAFETY LOCKING FEATURE INDICATES WHETHER OR NOT A DEVICE DESIGNED TO LOCK THE COUPLING AGAINST ACCIDENTAL DISCONNECT IS INCLUDED. SELECT REPLY CODE 10AA49 ADLSD /D/ 18TYPE,SELF-SEALING SELF-SEALING TYPE THE INTEGRAL FEATURE DESIGNED TO PREVENT THE LOSS OF MEDIA UPON SEPARATION OF THE COUPLING HALVES. SELECT REPLY CODE 10AC45 ADLTG /D/ 19IDENTIFICATION,END,MATING MATING END IDENTIFICATION THE SPECIFIC MATING COUPLING HALF WITH WHICH THE ITEM MUST CONNECT. FULL TEXT WRITE-IN 0 ADLUD 18TYPE,CONNECTION,FIRST FLUID END FIRST FLUID END CONNECTION TYPE A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION. SELECT REPLY CODE 10AB76 ADLVJ /D/ 04LENGTH,THRU-HOLE,BOLT,FIRST END FIRST END BOLT THRU-HOLE LENGTH A MEASUREMENT THROUGH THE HOLE WITH TERMINATED POINTS ON THE TWO BEARING SURFACES. 2D AND 1B MODE REPLY21AA051AC20 ADLWJ /D/ 04LENGTH,THRU-HOLE,BOLT,SECOND END SECOND END BOLT THRU-HOLE LENGTH A MEASUREMENT THROUGH THE HOLE WITH TERMINATED POINTS ON THE TWO BEARING SURFACES. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 2D AND 1B MODE REPLY21AA051AC20 ADLXJ /D/ 04DIAMETER,THRU-HOLE,FIRST END BOLT FIRST END BOLT THRU-HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOLT THRU-HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADLYJ /D/ 04DIAMETER,THRU-HOLE,SECOND END BOLT SECOND END BOLT THRU-HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOLT THRU-HOLE,AND TERMINATES AT THE CIRCUMFERENCE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 2D AND 1B MODE REPLY21AA051AC20 ADLZD /D/ 08LOCATION,END,FLUID,FIRST END FIRST END FLUID END LOCATION INDICATES THE LOCATION OF THE SPECIFIC LEG(S) TO WHICH A FLUID END CONNECTION IS ATTACHED. SELECT REPLY CODE 10AE46 ADMAD /D/ 08LOCATION,END,FLUID,SECOND END SECOND END FLUID END LOCATION INDICATES THE LOCATION OF THE SPECIFIC LEG(S) TO WHICH A FLUID END CONNECTION IS ATTACHED. SELECT REPLY CODE 10AE46 ADMBD /D/ 18TYPE,CONNECTION,SECOND FLUID END SECOND FLUID END CONNECTION TYPE A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION. SELECT REPLY CODE 10AB76 ADMCD /D/ 08LOCATION,FLANGE,MOUNTING MOUNTING FLANGE LOCATION INDICATES THE LOCATION OF THE MOUNTING FLANGE ON THE ITEM. SELECT REPLY CODE 10AE46 ADMDL 16STYLE,SHAPE,MOUNTING FLANGE MOUNTING FLANGE SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE MOUNTING FLANGE. 1L MODE REPLY 0 ADMEJ 04DIAMETER,OUTSIDE,MOUNTING FLANGE MOUNTING FLANGE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING FLANGE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADMFJ 04THICKNESS,FLANGE,MOUNTING MOUNTING FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADMGJ 04LENGTH,FLANGE,MOUNTING MOUNTING FLANGE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A MOUNTING FLANGE, IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADMHJ 04WIDTH,FLANGE,MOUNTING MOUNTING FLANGE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A MOUNTING FLANGE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ADMJJ /D/ 04RADIUS,END,MOUNTING FLANGE MOUNTING FLANGE END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADMKJ /D/ 04WIDTH ACROSS FLATS,FLANGE,MOUNTING MOUNTING FLANGE WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADMLA 12QUANTITY,HOLE,BOLT,MOUNTING FLANGE MOUNTING FLANGE BOLT HOLE QUANTITY THE NUMBER OF BOLT HOLES IN THE MOUNTING FLANGE. 1A MODE REPLY 0 ADMMJ 04DIAMETER,HOLE,BOLT,MOUNTING FLANGE MOUNTING FLANGE BOLT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING FLANGE BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADMNJ 04DIAMETER,CIRCLE,BOLT,MOUNTING FLANGE MOUNTING FLANGE BOLT CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING FLANGE BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADMPJ /D/ 04DISTANCE BETWEEN BOLT HOLES ALONG LENGTH,MOUNTING FLANGE MOUNTING FLANGE DISTANCE BETWEEN BOLT HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADMQJ /D/ 04DISTANCE BETWEEN BOLT HOLES ALONG WIDTH,FLANGE,MOUNTING MOUNTING FLANGE DISTANCE BETWEEN BOLT HOLES ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADMRD /D/ 08LOCATION,FACILITY,WRENCHING WRENCHING FACILITY LOCATION INDICATES THE LOCATION OF THE WRENCHING FACILITY ON THE ITEM. SELECT REPLY CODE 10AE46 ADMSJ 04DIAMETER,OUTSIDE,WRENCHING FACILITY WRENCHING FACILITY OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WRENCHING FACILITY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADMTJ 04DIAMETER,MAJOR,TAPERED HOLE TAPERED HOLE MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST END OF A TAPERED HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADMUD /D/ 02DESIGN,BODY BODY DESIGN THE CONFIGURATION OF THE PRINCIPAL PART REPRESENTING THE OUTSIDE SHAPE AND/OR THE INTERNAL FLOW PATTERN. SELECT REPLY CODE 10AC46 ADMVJ /D/ 04LENGTH FROM FLUID END TO FLOW ANGLE CENTERLINE LENGTH FROM FLUID END TO FLOW ANGLE CENTERLINE THE MEASURED DISTANCE OF A STRAIGHT LINE,FROM THE EXTREME OUTSIDE END SURFACE OF THE FLUID END CONNECTION TO AN INTERSECTION WITH THE CENTERLINE OF THE QUICK DISCONNECT OR SELF-SEALING END CONNECTION. 2D AND 1B MODE REPLY21AA051AC20 ADMWB 04ANGLE IN DEG,BODY BODY ANGLE IN DEG THE ANGLE THE END/S/ OR LEGS DEVIATE FROM THE CENTERLINE OF THE INLET END,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ADMXD /D/ 18TYPE,CONNECTION,END,QUICK DISCONNECT QUICK DISCONNECT END CONNECTION TYPE INDICATES WHETHER THE END CONNECTION IS EXTERNAL OR INTERNAL. SELECT REPLY CODE 10AE46 ADMYJ 04DISTANCE FROM MOUNTING FLANGE TO FLUID END DISTANCE FROM MOUNTING FLANGE TO FLUID END THE DISTANCE FROM THE BEARING SURFACE OF THE FLANGE TO THE END OF THE LEG PORTION OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ADMZJ 04DIAMETER,OUTSIDE,MAJOR MAJOR OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST END OF AN ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADNAJ 04DIAMETER,MINOR,OUTSIDE MINOR OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADNBJ 04LENGTH,SPOOL SPOOL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADNCA 19NUMBER,PART,REMOVABLE NUT MANUFACTURER REMOVABLE NUT MANUFACTURER PART NUMBER THE IDENTIFYING PART NUMBER ASSIGNED TO THE REMOVABLE NUT BY THE MANUFACTURER. 1A MODE REPLY 0 ADNDJ /D/T13THREAD PITCH DIAMETERS,MOUNTING MOUNTING THREAD PITCH DIAMETERS NONE. 1D AND 1F MODE REPLY11AA05 ADNED 13DIRECTION,THREAD,MOUNTING MOUNTING THREAD DIRECTION THE DIRECTION OF THE MOUNTING THREAD WHEN VIEWED AXIALLY.A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ADNFD /D/ 09MATERIAL,FILTERING FILTERING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FILTERING MATERIAL IS COMPOSED.PLEASE USE MRC BYTX IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 ADNGD 02DESIGN,MATERIAL,FILTERING FILTERING MATERIAL DESIGN THE DESIGN OF THE FABRICATED FILTERING MATERIAL. SELECT REPLY CODE 10AC48 ADNHJ 10FILTRATION RATING IN MICRONS FILTRATION RATING IN MICRONS THE SIZE OF THE SMALLEST PARTICLE WHICH THE ELEMENT IS CAPABLE OF REMOVING FROM THE FLUID WHICH PASSES THROUGH THE FILTERING MATERIAL. 1D AND 1B MODE REPLY11AC20 ADNJD /D/ 07FEATURE,REUSABILITY REUSABILITY FEATURE THE DESIGN CAPABILITY WHICH ALLOWS AN ITEM TO BE CLEANED AND REUSED. SELECT REPLY CODE 10AC49 ADNKD 05DIRECTION,FLOW FLOW DIRECTION THE DIRECTION IN WHICH THE FLUID IS PASSED THROUGH THE ITEM. SELECT REPLY CODE 10AC50 ADNLJ 10AREA,SURFACE,FILTERING FILTERING SURFACE AREA THE AMOUNT OF SURFACE AREA OF THE FILTERING MATERIAL THROUGH WHICH THE FLUID FLOWS. 1D AND 1B MODE REPLY11AC51 ADNMD /D/ 09MATERIAL,FRAME FRAME MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FRAME IS FABRICATED. PLEASE USE MRC CYAR OR MATT IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 ADNND /D/ 09MATERIAL,CONTAINER CONTAINER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CONTAINER IS FABRICATED. PLEASE USE MRC MATT WITH ISAC CODING IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 ADNPJ 10PRESSURE,DROP DROP PRESSURE THE AMOUNT OF PRESSURE LOSS IN THE SYSTEM,DUE TO THE RESISTANCE OF FLOW THROUGH THE ITEM. 1D AND 1B MODE REPLY11AB18 ADNQJ 10PRESSURE,DIFFERENTIAL DIFFERENTIAL PRESSURE THE DIFFERENCE IN OPPOSING PRESSURE WHICH AN ITEM IS CAPABLE OF WITHSTANDING WITHOUT EVIDENCE OF DEFORMATION OR OTHER DAMAGE. 1D AND 1B MODE REPLY11AB18 ADNRD /D/ 19MEDIA FOR WHICH DESIGNED,FILTERED FILTERED MEDIA FOR WHICH DESIGNED THE TYPE OF SERVICE WITH WHICH THE ITEM IS DESIGNED TO BE USED. SELECT REPLY CODE 10AB75 ADNSJ 10VELOCITY,FACE FACE VELOCITY THE MEASURED RATE OF AIR FLOW AT WHICH THE FILTER CAPACITY IS ESTABLISHED. 1D AND 1B MODE REPLY11AA22 ADNTJ T10RANGE,SETTING,BYPASS RELIEF VALVE BYPASS RELIEF VALVE SETTING RANGE THE PRESSURE RANGE AT WHICH THE BYPASS RELIEF VALVE FUNCTIONS. 1D AND 1F MODE REPLY11AB18 ADNUJ 04RADIUS,CORNER CORNER RADIUS A MEASUREMENT OF A STRAIGHT LINE FROM THE MIDPOINT OF A ROUNDED CORNER TO ITS PERIPHERY. 2D AND 1B MODE REPLY21AA051AC20 ADNVA 12QUANTITY ALONG LENGTH,HOLE HOLE QUANTITY ALONG LENGTH NONE. 1A MODE REPLY 0 ADNWA 12QUANTITY ALONG WIDTH,HOLE HOLE QUANTITY ALONG WIDTH NONE. 1A MODE REPLY 0 ADNXJ 04RADIUS,BODY BODY RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADNYJ 04DISTANCE BETWEEN HOLES ALONG LENGTH DISTANCE BETWEEN HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADNZJ 04DISTANCE BETWEEN HOLES ALONG WIDTH DISTANCE BETWEEN HOLES ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADPAJ 04DISTANCE BETWEEN HOLE CENTERLINE AND FIRST HOLE ALONG LENGTH DISTANCE BETWEEN HOLE CENTERLINE AND FIRST HOLE ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADPBJ 04DISTANCE BETWEEN HOLE CENTERLINE AND FIRST HOLE ALONG WIDTH DISTANCE BETWEEN HOLE CENTERLINE AND FIRST HOLE ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADPCJ 04DISTANCE FROM FIRST HOLE CENTERLINE TO END ALONG LENGTH DISTANCE FROM FIRST HOLE CENTERLINE TO END ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADPDJ 04DISTANCE FROM FIRST HOLE CENTERLINE TO END ALONG WIDTH DISTANCE FROM FIRST HOLE CENTERLINE TO END ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADPEJ 04LENGTH,BEVEL,CORNER CORNER BEVEL LENGTH THE LENGTH OF A LINEAR BREAK AT AN ANGLE TO THE SURFACES FORMING THE EDGE. 2D AND 1B MODE REPLY21AA051AC20 ADPFJ 04RADIUS,INVERTED INVERTED RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADPGJ 04RADIUS,EAR EAR RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADPHA 12QUANTITY,EAR EAR QUANTITY NONE. 1A MODE REPLY 0 ADPJA 12QUANTITY,CORNER CORNER QUANTITY NONE. 1A MODE REPLY 0 ADPKJ 04RADIUS,CENTERLINE,CORNER HOLE CORNER HOLE CENTERLINE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADPLJ /D/ 04DISTANCE FROM BODY CENTERLINE,OFFSET,EAR EAR OFFSET DISTANCE FROM BODY CENTERLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADPMA 12QUANTITY,HOLE,BOLT CIRCLE BOLT CIRCLE HOLE QUANTITY THE NUMBER OF HOLES IN A BOLT CIRCLE. 1A MODE REPLY 0 ADPNJ 04HEIGHT,INSIDE,FIRST RECESS FIRST RECESS INSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ADPPJ 04HEIGHT,INSIDE,SECOND RECESS SECOND RECESS INSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ADPQJ 04RADIUS,CORNER,INSIDE INSIDE CORNER RADIUS A MEASUREMENT OF THE LINE SEGMENT EXTENDING FROM THE CENTER OF A CIRCLE OR SPHERE TO THE CURVE OF AN INSIDE CORNER. 2D AND 1B MODE REPLY21AA051AC20 ADPRJ 04THICKNESS,BODY BODY THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A BODY,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADPSB 04ANGLE IN DEG,INSIDE INSIDE ANGLE IN DEG NONE. 1B MODE REPLY 0 ADPTJ 04DIAMETER,RECESS,FIRST FIRST RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADPUJ 04DIAMETER,RECESS,SECOND SECOND RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADPVJ 04RADIUS,SPHERICAL,BODY BODY SPHERICAL RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADPWJ 04RADIUS,CORNER,OUTSIDE OUTSIDE CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADPXJ 04RADIUS,OUTSIDE,BODY BODY OUTSIDE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADPYJ 04HEIGHT,PILOT PILOT HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ADPZJ /D/ 04DISTANCE,CENTER TO CENTER,SMALLEST SMALLEST CENTER TO CENTER DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADQAJ /D/ 04DISTANCE,CENTER TO CENTER,LARGEST LARGEST CENTER TO CENTER DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADQBD 18TYPE,DEVICE,SECURING SECURING DEVICE TYPE INDICATES THE TYPE OF DEVICE USED TO FASTEN THE ITEM. SELECT REPLY CODE 10AC52 ADQCD 18TYPE,DESIGN,VENTILATION VENTILATION DESIGN TYPE INDICATES THE TYPE OF DESIGN PROVIDED FOR VENTILATION OF THE ITEM. SELECT REPLY CODE 10AC53 ADQDD /D/ 19CAPABILITY,SEALING SEALING CAPABILITY THE ABILITY OF AN ITEM TO RESIST LEAKAGE AND PHYSICAL DEFORMITY WHEN AIR OR LIQUID IS APPLIED UNDER SPECIFIC CONDITIONS. SELECT REPLY CODE 10AC54 ADQED /D/ 07FACILITY,OBSERVATION OBSERVATION FACILITY INDICATES WHETHER OR NOT AN OBSERVATION FACILITY,SUCH AS A WINDOW OR THE LIKE,IS INCLUDED ON THE ITEM. SELECT REPLY CODE 10AA49 ADQFD 18TYPE,HANDLE HANDLE TYPE INDICATES THE TYPE OF HANDLE DESIGNED TO BE ATTACHED TO OR THROUGH AN ITEM FOR THE PURPOSE OF OPENING,LIFTING,CLOSING,OR THE LIKE. SELECT REPLY CODE 10AC55 ADQGJ /D/ 04DIAMETER,INSIDE,NOMINAL,DUCT ACCOMMODATED DUCT ACCOMMODATED NOMINAL INSIDE DIAMETER THE NOMINAL DIMENSION SPECIFIED FOR THE INSIDE DIAMETER OF THE AIR DUCT ACCOMMODATED BY THE ITEM. 1D AND 1B MODE REPLY11AA05 ADQHD /D/ 18TYPE,FEATURE,SELF-CLOSING SELF-CLOSING FEATURE TYPE INDICATES THE TYPE OF INTEGRAL DEVICE THAT AUTOMATICALLY RETURNS THE ITEM TO ITS CLOSED POSITION. SELECT REPLY CODE 10AC56 ADQJD /D/ 09MATERIAL,REINFORCEMENT,SEAL SEAL REINFORCEMENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SEAL REINFORCEMENT IS FABRICATED. SELECT REPLY CODE 10AD09 ADQKL 16STYLE,SHAPE,MOUNTING OPENING MOUNTING OPENING SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE MOUNTING OPENING. 1L MODE REPLY 0 ADQLJ 04DISTANCE,FACE TO FACE FACE TO FACE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADQMJ 04DISTANCE,FACE TO CENTERLINE,FIRST CONNECTION FIRST CONNECTION FACE TO CENTERLINE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADQNJ 04DISTANCE,FACE TO CENTERLINE,SECOND CONNECTION SECOND CONNECTION FACE TO CENTERLINE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADQPJ 04DISTANCE,FACE TO CENTERLINE,THIRD CONNECTION THIRD CONNECTION FACE TO CENTERLINE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADQQJ 04DISTANCE,CONNECTION FACE TO CENTERLINE,FOURTH FOURTH CONNECTION FACE TO CENTERLINE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADQRJ 04DISTANCE,CENTER TO CENTER CENTER TO CENTER DISTANCE THE CENTER TO CENTER DISTANCE. 2D AND 1B MODE REPLY21AA051AC20 ADQSL 16STYLE,FLOW FLOW STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FLOW. 1L MODE REPLY 0 ADQTD /D/ 09MATERIAL,PACKING PACKING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PACKING IS FABRICATED. SELECT REPLY CODE 10AD09 ADQUD 19DEVICE,CONTROL,FLOW FLOW CONTROL DEVICE THE PART THAT CONTROLS THE FLOW THROUGH THE ITEM. SELECT REPLY CODE 10AC57 ADQVD /D/ 09MATERIAL,DEVICE,FLOW CONTROL FLOW CONTROL DEVICE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FLOW CONTROL DEVICE IS FABRICATED. PLEASE USE MRC MATT WITH ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 ADQWD /D/ 11METHOD,OPERATION,VALVE VALVE OPERATION METHOD THE MEANS USED TO CHANGE THE VALVE OPENING TO CONTROL THE FLOW OF FLUIDS OR GASES. PLEASE USE MRC AQLR IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AC58 ADQXJ /D/ 10PRESSURE,OPERATING,POWER DRIVE POWER DRIVE OPERATING PRESSURE THE PRESSURE REQUIRED TO ACTUATE THE POWER DRIVEN UNIT. PLEASE USE MRC CQCN IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1B MODE REPLY11AB18 ADQYB /D/ 10TIME IN SECONDS,OPERATING OPERATING TIME IN SECONDS THE PERIOD OF ELAPSED TIME BETWEEN THE OPENING AND CLOSING OF THE ITEM,EXPRESSED IN SECONDS. 1B MODE REPLY 0 ADQZA 12QUANTITY,CONNECTION,END END CONNECTION QUANTITY THE NUMBER OF END CONNECTIONS INCLUDED IN THE ITEM. 1A MODE REPLY 0 ADRAA /D/ 16STYLE DESIGNATOR,END,FIFTH FIFTH END STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE DESIGNED CONNECTION TYPE. 1A MODE REPLY 0 ADRBJ /D/ 04HEIGHT,FACE,RAISED,FIFTH END FIFTH END RAISED FACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ADRCJ /D/ 04DIAMETER,FACE,RAISED,FIFTH END FIFTH END RAISED FACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADRDJ /D/ 04DIAMETER,RECESS,FIFTH END FIFTH END RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADREJ /D/ 04DEPTH,RECESS,FIFTH END FIFTH END RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADRFA /D/ 16STYLE,SHAPE,FIFTH END FLANGE FIFTH END FLANGE SHAPE STYLE THE OUTSIDE CONFIGURATION OF THE FLANGE AS RELATED TO A REFERENCE DRAWING. 1A MODE REPLY 0 ADRGJ /D/ 04DIAMETER HOSE ACCOMMODATED,INSIDE,FIFTH END FIFTH END INSIDE DIAMETER HOSE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOSE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADRHJ /D/ 04DIAMETER HOSE ACCOMMODATED,OUTSIDE,FIFTH END FIFTH END OUTSIDE DIAMETER HOSE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOSE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADRJJ /D/ 04SIZE ACCOMMODATED,PIPE,NOMINAL,FIFTH END FIFTH END NOMINAL PIPE SIZE ACCOMMODATED THE INDUSTRAIL DESIGNATION OR TERM USED TO DEFINE THE DIAMETER OF THE PIPE. 1D AND 1B MODE REPLY11AA05 ADRKJ /D/ 04DIAMETER TUBE ACCOMMODATED,OUTSIDE,FIFTH END FIFTH END OUTSIDE DIAMETER TUBE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADRLJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,END,FIFTH FIFTH END THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AC21 ADRMA /D/ 13THREAD CLASS,END,FIFTH FIFTH END THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD. 1A MODE REPLY 0 ADRNJ T13THREAD PITCH DIAMETERS,END,FIRST FIRST END THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 ADRPJ T13THREAD PITCH DIAMETERS,END,SECOND SECOND END THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 ADRQJ T13THREAD PITCH DIAMETERS,END,THIRD THIRD END THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 ADRRJ /D/T13THREAD PITCH DIAMETERS,END,FOURTH FOURTH END THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 ADRSJ /D/T13THREAD PITCH DIAMETERS,END,FIFTH FIFTH END THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 ADRTD /D/ 13THREAD DIRECTION,END,FIFTH FIFTH END THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ADRUB /D/ 04ANGLE IN DEG,SEAT,FIFTH END FIFTH END SEAT ANGLE IN DEG THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ADRVJ /D/ 04RADIUS,SEAT,FIFTH END FIFTH END SEAT RADIUS THE RADIUS OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS. 2D AND 1B MODE REPLY21AA051AC20 ADRWD /D/ 19RELATIONSHIP WITH PRECEDING ENDS,FIFTH END FIFTH END RELATIONSHIP WITH PRECEDING ENDS INDICATES WHETHER OR NOT THE FIFTH END IS IDENTICAL WITH THE FIRST,SECOND,THIRD,OR FOURTH END. SELECT REPLY CODE 10AB78 ADRXD /D/ 18TYPE,CONNECTION,FIFTH END FIFTH END CONNECTION TYPE A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION. SELECT REPLY CODE 10AB76 ADRYJ /D/ 04DIAMETER,OUTSIDE,FLANGE,FIFTH END FIFTH END FLANGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADRZJ /D/ 04THICKNESS,FLANGE,FIFTH END FIFTH END FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADSAJ /D/ 04LENGTH,FLANGE,FIFTH END FIFTH END FLANGE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADSBJ /D/ 04WIDTH,FLANGE,FIFTH END FIFTH END FLANGE WIDTH NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 2D AND 1B MODE REPLY21AA051AC20 ADSCJ /D/ 04RADIUS,END,FLANGE,FIFTH END FIFTH END FLANGE END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADSDJ /D/ 04WIDTH ACROSS FLATS,FIFTH END FIFTH END WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADSEA /D/ 12QUANTITY,HOLE,BOLT,FIFTH END FIFTH END BOLT HOLE QUANTITY THE NUMBER OF BOLT HOLES PROVIDED ON THE ITEM. 1A MODE REPLY 0 ADSFJ /D/ 04DIAMETER,HOLE,BOLT,FIFTH END FIFTH END BOLT HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADSGJ /D/ 04DIAMETER,CIRCLE,BOLT,FIFTH END FIFTH END BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADSHJ /D/ 04DISTANCE BETWEEN BOLT HOLES ALONG LENGTH,FIFTH END FIFTH END DISTANCE BETWEEN BOLT HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADSJJ /D/ 04DISTANCE BETWEEN BOLT HOLES ALONG WIDTH,FIFTH END FIFTH END DISTANCE BETWEEN BOLT HOLES ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADSKD 19POSITION,OPERATING,NORMAL,FLOW CONTROL DEVICE FLOW CONTROL DEVICE NORMAL OPERATION POSITION THE POSITION OF THE MOVING MEMBER/S/ CONTROLLING FLOW THROUGH THE VALVE WITH THE SOLENOID IN THE DE-ENERGIZED POSITION. SELECT REPLY CODE 10AC59 ADSLJ /D/ 10DIFFERENTIAL,PRESSURE,OPERATING,INLET AND OUTLET INLET AND OUTLET OPERATING PRESSURE DIFFERENTIAL THE DIFFERENCE AT THE RATED TEMPERATURE BETWEEN THE INLET AND OUTLET PRESSURE FOR POSITIVE OPERATION. 2D AND 1B MODE REPLY21AB181AC20 ADSMD /D/ 19POSITION,MOUNTING MOUNTING POSITION THE INSTALLED POSITION FOR WHICH THE ITEM IS DESIGNED. PLEASE USE MRC BBJX IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AC60 ADSND /D/ 07PRESSURE DETERMINATION WITH WEIGHTS,OPERATING OPERATING PRESSURE DETERMINATION WITH WEIGHTS INDICATES WHETHER OR NOT THE MAXIMUM OPERATING PRESSURE WAS TAKEN WITH WEIGHTS. SELECT REPLY CODE 10AA89 ADSPD /D/ 07SHIELD,LOCK,VALVE STEM VALVE STEM LOCK SHIELD INDICATES WHETHER OR NOT A DEVICE DESIGNED TO PREVENT TAMPERING OR ACCIDENTAL MOVEMENT OF THE VALVE STEM IS INCLUDED. SELECT REPLY CODE 10AA49 ADSQD 19ACTION,STEM STEM ACTION THE DIRECTION OR MOVEMENT OF THE STEM. SELECT REPLY CODE 10AC61 ADSRD 18TYPE,BONNET BONNET TYPE INDICATES THE TYPE OF HOUSING ON THE ITEM THAT ACCOMMODATES THE STEM PACKING OR SPRING. SELECT REPLY CODE 10AC62 ADSSD /D/ 07PACKING,BONNET BONNET PACKING INDICATES WHETHER OR NOT BONNET PACKING IS INCLUDED. SELECT REPLY CODE 10AA49 ADSTD 11METHOD,ATTACHMENT,BONNET BONNET ATTACHMENT METHOD THE MEANS BY WHICH THE BONNET IS ATTACHED TO THE ITEM. SELECT REPLY CODE 10AB47 ADSUD 11METHOD,LOADING,DISK DISK LOADING METHOD THE MEANS OF CLOSING THE ITEM WHEN INLET PRESSURE DECREASES. SELECT REPLY CODE 10AC63 ADSVJ /D/ 10SETTING,PRESSURE,OPENING OPENING PRESSURE SETTING THE PREDETERMINED PRESSURE AT WHICH THE ITEM IS CALIBRATED TO OPEN. 1D AND 1B MODE REPLY11AB18 ADSWJ /D/T10RANGE,PRESSURE,ADJUSTABLE ADJUSTABLE PRESSURE RANGE THE MINIMUM TO MAXIMUM PRESSURES AT WHICH THE ITEM MAY BE ADJUSTED. 1D AND 1F MODE REPLY11AB18 ADSXD /D/ 07SIDE,OUTLET,PRESSURE TIGHT PRESSURE TIGHT OUTLET SIDE A VALVE OF WHICH THE CASING IS PRESSURE TIGHT ABOVE THE VALVE SEAT. SELECT REPLY CODE 10AA89 ADSYJ 10FLOW RATE,DISCHARGE,VALVE VALVE DISCHARGE FLOW RATE THE RATED VALVE DISCHARGE CAPACITY PER UNIT OF TIME. 1D AND 1B MODE REPLY11AC64 ADSZD /D/ 18TYPE,STOP,ROTATION ROTATION STOP TYPE INDICATES THE TYPE OF FEATURE INCORPORATED IN THE ITEM WHICH LIMITS THE DEGREE OF PLUG TURN. SELECT REPLY CODE 10AC06 ADTAD /D/ 07POCKET,CLEANOUT CLEANOUT POCKET INDICATES WHETHER OR NOT A DESIGN FEATURE IN THE ITEM IS INCLUDED TO FACILITATE THE REMOVAL OF FOREIGN MATTER. SELECT REPLY CODE 10AA49 ADTBD /D/ 09MATERIAL,LINING,BODY BODY LINING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE WITH WHICH THE BODY OF THE ITEM IS LINED. SELECT REPLY CODE 10AD09 ADTCD /D/ 09MATERIAL,SEPARATOR SEPARATOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SEPARATOR IS FABRICATED. SELECT REPLY CODE 10AD09 ADTDJ 10PRESSURE RATING,NOMINAL NOMINAL PRESSURE RATING THE NOMINAL RATED PRESSURE THAT AN ITEM CAN BE EXPECTED TO WITHSTAND WITHOUT RUPTURE. 1D AND 1B MODE REPLY11AB18 ADTEL 16STYLE,JOINT JOINT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE JOINT. 1L MODE REPLY 0 ADTFA 12QUANTITY,JOINT JOINT QUANTITY THE NUMBER OF JOINTS IN THE ITEM. 1A MODE REPLY 0 ADTGA /D/ 16STYLE,CUT CUT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CUT. 1A MODE REPLY 0 ADTHA 12QUANTITY,RING,INTERMEDIATE INTERMEDIATE RING QUANTITY THE NUMBER OF RINGS BETWEEN THE TOP AND BOTTOM RINGS. 1A MODE REPLY 0 ADTJJ 04THICKNESS,RETAINER RETAINER THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE RETAINER,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADTKJ 04DIAMETER,CROSS-SECTIONAL,PACKING RING PACKING RING CROSS-SECTIONAL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PACKING RING IN CROSS SECTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADTLA 12QUANTITY,FEATURE,ATTACHMENT ATTACHMENT FEATURE QUANTITY THE NUMBER OF ATTACHMENT FEATURES INCLUDED. 1A MODE REPLY 0 ADTMJ 04DIAMETER,HOLE,ATTACHMENT ATTACHMENT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ATTACHMENT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADTNJ 04LENGTH,FEATURE,ATTACHMENT ATTACHMENT FEATURE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ATTACHMENT FEATURE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADTPJ 04WIDTH,FEATURE,ATTACHMENT ATTACHMENT FEATURE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ATTACHMENT FEATURE. 2D AND 1B MODE REPLY21AA051AC20 ADTQJ 04DIAMETER,CIRCLE,ATTACHMENT FEATURE ATTACHMENT FEATURE CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CIRCLE ON WHICH THE ATTACHMENT FEATURES ARE ALIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADTRJ /D/ 04DISTANCE,CENTER TO CENTER,ATTACHMENT FEATURE ATTACHMENT FEATURE CENTER TO CENTER DISTANCE THE DISTANCE BETWEEN THE CENTER OF ONE ATTACHMENT FEATURE AND THE CENTER OF THE ADJACENT ATTACHMENT FEATURE. 2D AND 1B MODE REPLY21AA051AC20 ADTSD 18TYPE,CONSTRUCTION CONSTRUCTION TYPE INDICATES THE TYPE OF CONSTRUCTION. SELECT REPLY CODE 10AC66 ADTTA 12QUANTITY,SEPARATOR SEPARATOR QUANTITY THE NUMBER OF SEPARATORS INCLUDED IN THE ITEM. 1A MODE REPLY 0 ADTUA 12QUANTITY,RING,LANTERN LANTERN RING QUANTITY THE NUMBER OF LANTERN RINGS IN THE ASSEMBLY. 1A MODE REPLY 0 ADTVD /D/ 09MATERIAL,CASE CASE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CASE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH ISAC CODING IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 ADTWD /D/ 09MATERIAL,ELEMENT,SEALING SEALING ELEMENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SEALING ELEMENT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ADTXD /D/ 19CONDITION,SURFACE SURFACE CONDITION THE CONDITION OF THE ITEM WITH RESPECT TO THE TEXTURE OF THE SURFACE. PLEASE USE MRC SFC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AC67 ADTYD /D/ 17SURFACE TREATMENT,CASE CASE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE CASE. PLEASE USE MRC CWKC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 ADTZD 18TYPE,CONSTRUCTION,SEAL SEAL CONSTRUCTION TYPE INDICATES THE TYPE OF DESIGN USED IN CONSTRUCTING THE SEAL. SELECT REPLY CODE 10AC68 ADUAA /D/ 16STYLE,CASE CASE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CASE. 1A MODE REPLY 0 ADUBA /D/ 16STYLE,ELEMENT,SEALING SEALING ELEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SEALING ELEMENT. 1A MODE REPLY 0 ADUCJ 04WIDTH,SEAL SEAL WIDTH A MEASUREMENT TAKEN BETWEEN THE FLAT SURFACES /FRONT AND BACK/ OF THE SEAL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ADUDJ /D/ 04DIAMETER,BORE,HOUSING HOUSING BORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOUSING BORE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADUEJ 04WIDTH,APERTURE APERTURE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN APERTURE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ADUFJ 04LENGTH,APERTURE APERTURE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN APERTURE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADUGJ 04LENGTH,BEVEL,OUTSIDE CORNER OUTSIDE CORNER BEVEL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADUHJ 04LENGTH,BEVEL,INSIDE CORNER INSIDE CORNER BEVEL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADUJB 04ANGLE IN DEG,CUT,END END CUT ANGLE IN DEG THE ANGLE OF THE END CUT,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ADUKJ 04LENGTH,CUT,END END CUT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADULJ 04DEPTH,CUT,END END CUT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADUMJ 04THICKNESS,OVERALL OVERALL THICKNESS AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADUNJ 04LENGTH,SMALLEST,END CUT END CUT SMALLEST LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADUPJ 04LENGTH ALONG WIDTH,BEVEL,OUTSIDE CORNER OUTSIDE CORNER BEVEL LENGTH ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADUQJ 04LENGTH ALONG LENGTH,BEVEL,OUTSIDE CORNER OUTSIDE CORNER BEVEL LENGTH ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADURJ 04LENGTH ALONG WIDTH,BEVEL,INSIDE CORNER INSIDE CORNER BEVEL LENGTH ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADUSJ 04LENGTH ALONG LENGTH,BEVEL,INSIDE CORNER INSIDE CORNER BEVEL LENGTH ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADUTJ 04RADIUS,INVERTED,INSIDE CORNER INSIDE CORNER INVERTED RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADUUJ 04RADIUS,INVERTED,OUTSIDE CORNER OUTSIDE CORNER INVERTED RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADUVJ 04WIDTH,SURFACE,BEARING BEARING SURFACE WIDTH A MEASUREMENT TAKEN ACROSS THE BEARING SURFACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ADUWJ 04LENGTH,HOLE,CENTER CENTER HOLE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADUXJ 04WIDTH,HOLE,CENTER CENTER HOLE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADUYJ 04DISTANCE BETWEEN BOLT HOLES ALONG WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG WIDTH A MEASUREMENT OF THE CENTER TO CENTER DISTANCE BETWEEN THE BOLT HOLES ALONG THE WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADUZJ 04DISTANCE BETWEEN BOLT HOLES ALONG LENGTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG LENGTH A MEASUREMENT OF THE CENTER TO CENTER DISTANCE BETWEEN THE BOLT HOLES ALONG THE LENGTH. 2D AND 1B MODE REPLY21AA051AC20 ADVAJ 04DIAMETER,OUTSIDE,GAGE RING GAGE RING OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADVBJ 04RADIUS FROM BOLT CIRCLE,SIDE SIDE RADIUS FROM BOLT CIRCLE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADVCJ 04RADIUS FROM GASKET CENTER,SIDE SIDE RADIUS FROM GASKET CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADVDJ 04DISTANCE ALONG WIDTH,OUTSIDE EDGE TO BOLT HOLE CENTER OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADVEJ 04DISTANCE ALONG LENGTH,OUTSIDE EDGE TO BOLT HOLE CENTER OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADVFA 12QUANTITY,FLAT,PERIPHERAL PERIPHERAL FLAT QUANTITY NONE. 1A MODE REPLY 0 ADVGJ 04DISTANCE,GASKET CENTER TO FLAT GASKET CENTER TO FLAT DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADVHJ 04DISTANCE,GASKET CENTER TO SECOND FLAT GASKET CENTER TO SECOND FLAT DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADVJJ 04DISTANCE,BOLT HOLE CENTERLINE TO NEAREST EDGE BOLT HOLE CENTERLINE TO NEAREST EDGE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADVKJ 04DIAMETER,INSIDE,CROSS SECTION CROSS SECTION INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CROSS SECTION,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADVLJ 04DIAMETER,OUTSIDE,CROSS SECTION CROSS SECTION OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CROSS SECTION,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADVMJ 04THICKNESS,CROSS-SECTIONAL CROSS-SECTIONAL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A CROSS SECTION,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADVNJ 04HEIGHT,CROSS-SECTIONAL CROSS-SECTIONAL HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A CROSS SECTION,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 ADVPJ 04DEPTH,GROOVE,OUTER OUTER GROOVE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADVQJ 04WIDTH,GROOVE,OUTER OUTER GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADVRB /D/ 04ANGLE IN DEG ANGLE IN DEG THE ANGLE FORMED BY THE ANGULAR PORTION OF THE ITEM,EXPRESSED IN DEGREES. PLEASE USE MRC CSXS IN PLACE OF THIS DISCONTINUED MRC. 1B MODE REPLY 0 ADVSJ 04DIAMETER,INSIDE,LIP LIP INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADVTJ 04DIAMETER,OUTSIDE,FLANGED BODY FLANGED BODY OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADVUB /D/ 04ANGLE IN DEG,EXTRUSION EXTRUSION ANGLE IN DEG NONE. 1B MODE REPLY 0 ADVVJ 04DIAMETER,RECESS,BODY BODY RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADVWJ 04DEPTH,RECESS,BODY BODY RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADVXJ 04WIDTH,SURFACE,RIM RIM SURFACE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADVYJ 04DEPTH,GROOVE,INNER INNER GROOVE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADVZJ 04WIDTH,SMALLEST,OUTER GROOVE OUTER GROOVE SMALLEST WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADWAJ 04WIDTH,GROOVE,INNER INNER GROOVE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE INNER GROOVE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ADWBJ 04DISTANCE BETWEEN ENDS DISTANCE BETWEEN ENDS THE DISTANCE BETWEEN THE ENDS OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ADWCJ 04LENGTH,RECESS RECESS LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A RECESS,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADWDJ 04LENGTH,CROSS-SECTIONAL CROSS-SECTIONAL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CROSS SECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADWEJ 04LENGTH,DIAMETER,RAISED RAISED DIAMETER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADWFJ 04THICKNESS,RING,GAGE GAGE RING THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADWGJ 04THICKNESS,GAGE GAGE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE GAGE, IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ADWHJ 04WIDTH,CROSS-SECTIONAL CROSS-SECTIONAL WIDTH A MEASUREMENT OF THE CROSS SECTION TAKEN AT RIGHT ANGLES TO THE LENGTH,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ADWJJ 04HEIGHT,ANGLE ANGLE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ADWKJ 04HEIGHT,MINOR MINOR HEIGHT A MINOR MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN OBJECT,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 ADWLJ /D/ 04HEIGHT,OFFSET,TOP TOP OFFSET HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ADWMJ /D/ 04HEIGHT,OFFSET,BOTTOM BOTTOM OFFSET HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ADWNJ /D/ 04WIDTH,OFFSET,TOP TOP OFFSET WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADWPJ /D/ 04WIDTH,OFFSET,BOTTOM BOTTOM OFFSET WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADWQB /D/ 04ANGLE IN DEG,PROTUBERANCE PROTUBERANCE ANGLE IN DEG NONE. 1B MODE REPLY 0 ADWRJ 04WIDTH,PROTUBERANCE PROTUBERANCE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADWSJ /D/ 04HEIGHT,FLANGE,RIGHT/BASE RIGHT/BASE FLANGE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ADWTJ 04HEIGHT,FLANGE,LEFT LEFT FLANGE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ADWUJ 04THICKNESS AT TOE,FLANGE,LEFT LEFT FLANGE THICKNESS AT TOE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADWVJ 04THICKNESS AT TOE,FLANGE,RIGHT/BASE RIGHT/BASE FLANGE THICKNESS AT TOE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADWWJ 04THICKNESS AT HEEL,FLANGE,RIGHT/BASE RIGHT/BASE FLANGE THICKNESS AT HEEL NONE. 2D AND 1B MODE REPLY21AA051AC20 ADWXJ 04THICKNESS AT HEEL,FLANGE,LEFT LEFT FLANGE THICKNESS AT HEEL NONE. 2D AND 1B MODE REPLY21AA051AC20 ADWYJ 04RADIUS WHERE FLANGES JOIN,INNER INNER RADIUS WHERE FLANGES JOIN NONE. 2D AND 1B MODE REPLY21AA051AC20 ADWZJ 04RADIUS WHERE FLANGES JOIN,OUTER OUTER RADIUS WHERE FLANGES JOIN NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXAJ 04DISTANCE,OUTER HEEL,FLANGE TO FLANGE FLANGE TO FLANGE OUTER HEEL DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXBJ /D/ 04RADIUS AT TOE,OUTER SIDE,LEFT FLANGE LEFT FLANGE OUTER SIDE RADIUS AT TOE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXCJ /D/ 04RADIUS AT TOE,INNER SIDE,LEFT FLANGE LEFT FLANGE INNER SIDE RADIUS AT TOE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXDJ /D/ 04RADIUS,FILLET,LEFT SIDE FLANGE LEFT SIDE FLANGE FILLET RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXEJ 04RADIUS AT TOE,INNER SIDE,RIGHT FLANGE RIGHT FLANGE INNER SIDE RADIUS AT TOE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXFJ 04RADIUS AT TOE,OUTER SIDE,RIGHT FLANGE RIGHT FLANGE OUTER SIDE RADIUS AT TOE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXGJ /D/ 04RADIUS,FILLET,RIGHT SIDE FLANGE RIGHT SIDE FLANGE FILLET RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXHJ 04WIDTH,WEB WEB WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXJJ 04HEIGHT,FLANGE,LEFT SIDE LEFT SIDE FLANGE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXKJ 04HEIGHT,FLANGE,RIGHT SIDE RIGHT SIDE FLANGE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXLJ 04THICKNESS,FLANGE,LEFT SIDE LEFT SIDE FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXMJ 04THICKNESS,FLANGE,RIGHT SIDE RIGHT SIDE FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXNJ 04THICKNESS,WEB WEB THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXPJ 04THICKNESS AT WEB,FLANGE,LEFT SIDE LEFT SIDE FLANGE THICKNESS AT WEB NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXQJ 04THICKNESS AT WEB,FLANGE,RIGHT SIDE RIGHT SIDE FLANGE THICKNESS AT WEB NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXRJ 04THICKNESS,FLANGE,LEFT SIDE TOP LEFT SIDE TOP FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXSJ 04THICKNESS,FLANGE,RIGHT SIDE TOP RIGHT SIDE TOP FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXTJ /D/ 04HEIGHT,END,LEFT SIDE FLANGE LEFT SIDE FLANGE END HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXUJ /D/ 04HEIGHT,END,RIGHT SIDE FLANGE RIGHT SIDE FLANGE END HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXVJ 04RADIUS AT WEB,FILLET,LEFT FLANGE LEFT FLANGE FILLET RADIUS AT WEB NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXWJ 04RADIUS AT WEB,OUTER,LEFT FLANGE LEFT FLANGE OUTER RADIUS AT WEB NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXXJ 04RADIUS AT WEB,FILLET,RIGHT FLANGE RIGHT FLANGE FILLET RADIUS AT WEB NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXYJ 04RADIUS AT WEB,OUTER,RIGHT FLANGE RIGHT FLANGE OUTER RADIUS AT WEB NONE. 2D AND 1B MODE REPLY21AA051AC20 ADXZB 04ANGLE IN DEG,INSIDE,LEFT LEFT INSIDE ANGLE IN DEG NONE. 1B MODE REPLY 0 ADYAB 04ANGLE IN DEG,INSIDE,RIGHT RIGHT INSIDE ANGLE IN DEG NONE. 1B MODE REPLY 0 ADYBB 04ANGLE IN DEG,OUTSIDE,LEFT LEFT OUTSIDE ANGLE IN DEG NONE. 1B MODE REPLY 0 ADYCB 04ANGLE IN DEG,OUTSIDE,RIGHT RIGHT OUTSIDE ANGLE IN DEG NONE. 1B MODE REPLY 0 ADYDJ /D/ 04DIAMETER,INSIDE,LEFT SIDE FLANGE TOP LEFT SIDE FLANGE TOP INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADYEJ /D/ 04DIAMETER,INSIDE,RIGHT SIDE FLANGE TOP RIGHT SIDE FLANGE TOP INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADYFJ 04RADIUS,OUTER,LEFT SIDE FLANGE TOP LEFT SIDE FLANGE TOP OUTER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADYGJ 04RADIUS,INNER,LEFT SIDE FLANGE TOP LEFT SIDE FLANGE TOP INNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADYHJ 04RADIUS,INNER,RIGHT SIDE FLANGE TOP RIGHT SIDE FLANGE TOP INNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADYJJ 04RADIUS,OUTER,RIGHT SIDE FLANGE TOP RIGHT SIDE FLANGE TOP OUTER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADYKJ /D/ 04RADIUS,FILLET,LEFT SIDE FLANGE LEFT SIDE FLANGE FILLET RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADYLJ /D/ 04RADIUS,FILLET,RIGHT SIDE FLANGE RIGHT SIDE FLANGE FILLET RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ADYMJ 04WIDTH,FLANGE,LEFT SIDE TOP LEFT SIDE TOP FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADYNJ 04WIDTH,FLANGE,RIGHT SIDE TOP RIGHT SIDE TOP FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ADYPJ 04RADIUS WHERE LEFT FLANGE JOINS TOP FLANGE,OUTER OUTER RADIUS WHERE LEFT FLANGE JOINS TOP FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADYQJ 04RADIUS WHERE LEFT FLANGE JOINS TOP FLANGE,FILLET FILLET RADIUS WHERE LEFT FLANGE JOINS TOP FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADYRJ 04RADIUS WHERE RIGHT FLANGE JOINS TOP FLANGE,OUTER OUTER RADIUS WHERE RIGHT FLANGE JOINS TOP FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADYSJ 04RADIUS WHERE RIGHT FLANGE JOINS TOP FLANGE,FILLET FILLET RADIUS WHERE RIGHT FLANGE JOINS TOP FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 ADYTJ 04DIAMETER,HOLE,CENTER CENTER HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CENTER HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ADYUJ 04DIAMETER,PERIPHERAL PERIPHERAL DIAMETER A MEASUREMENT OF A STRAIGHT LINE FROM THE CENTER OF THE ITEM TO THE PERIPHERY OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ADYVD 08LOCATION,SURFACE,SMOOTH FINISH SMOOTH FINISH SURFACE LOCATION INDICATES THE LOCATION OF THE SURFACE THAT HAS BEEN MADE FREE OF IRREGULARITIES AND PROJECTIONS. SELECT REPLY CODE 10AE46 ADYWD /D/ 09MATERIAL,BINDER BINDER MATERIAL A SUBSTANCE OR COMBINATION OF SUBSTANCES USED TO UNITE AND GIVE SOLIDITY TO THE ITEM. SELECT REPLY CODE 10AD09 ADYXD /D/ 09MATERIAL,COVERING,PROTECTIVE PROTECTIVE COVERING MATERIAL THE BACKING OR COATING THAT IS APPLIED TO THE SURFACE FOR PROTECTION OF THE BASIC MATERIAL. IT IS INTENDED TO BE STRIPPED OFF PRIOR TO APPLICATION OF THE FABRICATED ITEM,AND IS NOT INTENDED TO BECOME PART OF THE SEALING SURFACE. EXCLUDES SURFACE TREATMENTS,ADHESIVE COATINGS,AND LUBRICANTS. SELECT REPLY CODE 10AD09 ADYYD /D/ 09MATERIAL,COATING COATING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE WITH WHICH THE ITEM IS COATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ADYZD /D/ 08LOCATION,MATERIAL,COATING COATING MATERIAL LOCATION INDICATES THE LOCATION OF THE ITEM TO WHICH A COATING HAS BEEN APPLIED. PLEASE USE MRC AQDY IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AE46 ADZAD /D/ 09MATERIAL,FEATURE,STRENGTHENING STRENGTHENING FEATURE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE STRENGTHENING FEATURE IS FABRICATED. PLEASE USE MRC ADZK AND RELATIONSHIP WITH MRC MATT. SELECT REPLY CODE 10AD09 ADZBJ A10STRENGTH,FLEXURAL FLEXURAL STRENGTH THE MAXIMUM LOAD WHICH CAN BE APPLIED NORMALLY TO THE PLANE OF THE MATERIAL,PER UNIT OF CROSS-SECTIONAL AREA,THAT AN ITEM CAN WITHSTAND WITHOUT FRACTURE. 1D AND 1A MODE REPLY11AB18 ADZCD 19PROTECTION,ENVIRONMENTAL ENVIRONMENTAL PROTECTION THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT AN ITEM IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY. SELECT REPLY CODE 10AA65 ADZDD /D/ 09MATERIAL,PRIMARY,ADHESIVE COMPOUND ADHESIVE COMPOUND PRIMARY MATERIAL THE GENERIC NAME OF THE PRIMARY COMPONENT OF THE ADHESIVE COMPOUND. SELECT REPLY CODE 10AD09 ADZEJ /D/ 04DISTANCE BETWEEN MOUNTING HOLES ALONG HEIGHT,CENTER TO CENTER,SECOND SURFACE SECOND SURFACE CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES ALONG HEIGHT THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING HOLE AND THE CENTER OF THE ADJACENT MOUNTING HOLE ALONG THE HEIGHT OF THE SECOND SURFACE. 2D AND 1B MODE REPLY21AA051AC20 ADZFD /D/ 09MATERIAL,TREATMENT,FRICTION FRICTION TREATMENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE WITH WHICH THE ITEM IS TREATED TO INDUCE FRICTION. SELECT REPLY CODE 10AD09 ADZGD /D/ 09MATERIAL,LUBRICATION LUBRICATION MATERIAL THE ELEMENT COMPOUND OR MIXTURE WITH WHICH THE ITEM IS LUBRICATED. PLEASE USE MRC LBMA AS A REPLACEMENT FOR CANCELED MRC. SELECT REPLY CODE 10AD09 ADZHD 18TYPE,RING,SEAT,RENEWABLE RENEWABLE SEAT RING TYPE INDICATES THE TYPE OF RENEWABLE SEATING RING IN THE ITEM. SELECT REPLY CODE 10AC69 ADZJD /D/ 19FACILITY,MOUNTING MOUNTING FACILITY THE MEANS OTHER THAN THE END CONNECTION/S/ BY WHICH THE ITEM MAY BE MOUNTED. SELECT REPLY CODE 10AC70 ADZKD 19FEATURE,STRENGTHENING STRENGTHENING FEATURE AN INTEGRAL FEATURE OF THE ITEM WHICH STRENGTHENS AND/OR STIFFENS THE BASIC MATERIAL. SELECT REPLY CODE 10AC71 ADZLD /D/ 08LOCATION,FEATURE,STRENGTHENING,EXTERNAL EXTERNAL STRENGTHENING FEATURE LOCATION INDICATES THE LOCATION(S) OF THE EXTERNAL STRENGTHENING FEATURE ON THE ITEM.PLEASE USE MRC ADZK WITH ISAC CODING TO IDENTIFY THE LOCATION. SELECT REPLY CODE 10AE46 ADZMA 12QUANTITY,INSERT INSERT QUANTITY THE NUMBER OF INSERTS/INTERLINERS CONTAINED IN THE ITEM. 1A MODE REPLY 0 ADZND /D/ 08LOCATION,CONDITION,SURFACE SURFACE CONDITION LOCATION INDICATES THE LOCATION OF AN ITEM TO WHICH A SURFACE CONDITION IS APPLICABLE. SELECT REPLY CODE 10AE46 ADZPD 05DIRECTION,CORRUGATION CORRUGATION DIRECTION THE DIRECTION OF THE CORRUGATIONS IN RELATION TO THE SHAPE OF THE ITEM. SELECT REPLY CODE 10AC72 ADZQJ 04DISTANCE BETWEEN CORRUGATIONS,CENTER TO CENTER,NOMINAL NOMINAL CENTER TO CENTER DISTANCE BETWEEN CORRUGATIONS THE DISTANCE FROM THE CREST OF ONE CORRUGATION TO THE CREST OF AN ADJACENT CORRUGATION. 1D AND 1B MODE REPLY11AA05 ADZRJ 04DEPTH,CORRUGATION,NOMINAL NOMINAL CORRUGATION DEPTH THE VERTICAL DISTANCE BETWEEN THE PLANE OF THE CREST AND THE BOTTOM OF THE VALLEY. 1D AND 1B MODE REPLY11AA05 ADZSD 18TYPE,FIBER FIBER TYPE INDICATES THE TYPE OF FIBER CONTAINED IN THE ITEM. SELECT REPLY CODE 10AC73 ADZTA /D/ 16STYLE,SHANK SHANK STYLE THE PHYSICAL CONFIGURATION OF THAT PORTION OF THE ROD OR ACCESSORY THAT IS INSERTED INTO THE CHUCK OF THE ROCK DRILL ON PAVING BREAKER FOR THE PURPOSE OF RETAINING THE ROD OR ACCESSORY,AS RELATED TO REFERENCE DRAWINGS. 1A MODE REPLY 0 ADZUJ /D/ 04DIAMETER,SPLINE SPLINE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ADZVJ 04SIZE,NOMINAL,ROD ROD NOMINAL SIZE THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL SIZE OF THE ROD. 1D AND 1B MODE REPLY11AA05 ADZWA /D/ 12QUANTITY,EDGE,CUTTING CUTTING EDGE QUANTITY THE NUMBER OF INDIVIDUAL CUTTING SURFACES CONTAINED ON THE CUTTING END OF THE ITEM. 1A MODE REPLY 0 ADZXD /D/ 07INSERTS,TUNGSTEN CARBIDE TUNGSTEN CARBIDE INSERTS INDICATES WHETHER OR NOT THE CUTTING EDGES OF THE ITEM INCLUDE PERMANENTLY BONDED INSERTS CONSTRUCTED OF TUNGSTEN CARBIDE. SELECT REPLY CODE 10AA49 ADZYJ 04SIZE FOR WHICH DESIGNED,ROD,NOMINAL NOMINAL ROD SIZE FOR WHICH DESIGNED THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL SIZE OF THE ROD FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AA05 ADZZL 16STYLE,BLADE BLADE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BLADE. 1L MODE REPLY 0 AEAAJ /D/ 04THICKNESS FOR WHICH DESIGNED,SHEETING SHEETING THICKNESS FOR WHICH DESIGNED THE DIMENSION REPRESENTING THE SHEETING THICKNESS THE ITEM IS DESIGNED TO DRIVE,OR THICKNESSES IF THE DRIVER IS ADJUSTABLE TO VARIOUS SIZES OF SHEETING. 1D AND 1B MODE REPLY11AA05 AEABD /D/ 14SHAPE,PAD PAD SHAPE THE PHYSICAL CONFIGURATION OF THE FLAT SURFACE OF THE PAD. SELECT REPLY CODE 10AD07 AEACJ 04DIAMETER,PAD PAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PAD,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AEADJ /D/ 04WIDTH ACROSS FLATS,PAD PAD WIDTH ACROSS FLATS THE DIMENSION MEASURED FROM ONE FLAT SURFACE TO THE OPPOSITE FLAT SURFACE OF THE PAD. 2D AND 1B MODE REPLY21AA051AC20 AEAEJ 04LENGTH,BLADE BLADE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BLADE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AEAFJ 04WIDTH,BLADE BLADE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BLADE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AEAGD 03DESIGNATION,DESIGN,THREAD,MANUFACTURER MANUFACTURER THREAD DESIGN DESIGNATION THE NAME OF THE MANUFACTURER,SUPPLIER,ASSOCIATION,OR INDUSTRIAL OR GOVERNMENTAL AGENCY WHICH CONTROLS THE THREAD DESIGN,AND THE ENTITY IDENTIFYING NUMBER. SELECT REPLY CODE 10AC74 AEAHD 11METHOD,LUBRICATION LUBRICATION METHOD THE MEANS BY WHICH THE ITEM IS LUBRICATED. SELECT REPLY CODE 10AC75 AEAJD /D/ 08LOCATION,LUBRICATION LUBRICATION LOCATION INDICATES THE LOCATION OF THE LUBRICANT ON THE ITEM. SELECT REPLY CODE 10AE46 AEAKD /D/ 07BOX,TERMINAL TERMINAL BOX INDICATES WHETHER OR NOT A TERMINAL BOX WITH COVER IS INCLUDED WITH AND CONNECTED TO THE ITEM. SELECT REPLY CODE 10AA49 AEALD /D/ 08LOCATION,HOLE,CLEANING CLEANING HOLE LOCATION INDICATES THE LOCATION OF HOLES IN THE ITEM WHICH ALLOW THE INJECTION OF AIR OR WATER TO REMOVE THE PULVERIZED DEBRIS. SELECT REPLY CODE 10AE46 AEAMA /D/ 12QUANTITY,HOLE,CLEANING CLEANING HOLE QUANTITY THE NUMBER OF CLEANING HOLES LOCATED IN THE ITEM. 1A MODE REPLY 0 AEAND /D/ 11METHOD,ATTACHMENT,BIT BIT ATTACHMENT METHOD THE MEANS BY WHICH THE BIT IS JOINED TO THE DRILL ROD AND THEREBY PROVIDES A MEANS OF TRANSMITTING MOTION FROM THE DRILL ROD TO THE BIT. SELECT REPLY CODE 10AB47 AEAPJ 04DIAMETER,HOLE,DRILLED DRILLED HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DRILLED HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AEAQD 03DESIGNATION,END END DESIGNATION THE END OF THE ITEM BEING USED AS A REFERENCE. SELECT REPLY CODE 10AC76 AEARJ /D/ 04LENGTH,PLATE,TOP TOP PLATE LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE TOP PLATE. 2D AND 1B MODE REPLY21AA051AC20 AEASG 19COMPONENTS,MAJOR MAJOR COMPONENTS THE PRINCIPAL PARTS THAT ARE INCLUDED IN AN ASSEMBLED UNIT. FULL TEXT WRITE-IN 0 AEATJ A10SPEED,RATED,MAXIMUM,ACCOMMODATED SHAFT ACCOMMODATED SHAFT MAXIMUM RATED SPEED THE MAXIMUM RATED SPEED OF THE ACCOMMODATED ROTATING SHAFT. 1D AND 1A MODE REPLY11AA22 AEAUJ 10VALUE,CAPACITANCE CAPACITANCE VALUE THE RELATIVE LEVEL OF THE NUMBER OF ELECTRIC CHARGE AT A GIVEN POTENTIAL WHICH THE CAPACITOR IS CAPABLE OF RECEIVING AND STORING. 1D AND 1B MODE REPLY11AC77 AEAVJ T10TOLERANCE,CAPACITANCE CAPACITANCE TOLERANCE THE LIMITS OF PERMISSIBLE RANGE IN CAPACITANCE VALUE OF AN ITEM FROM ITS RATED VALUE, 1D AND 1F MODE REPLY11AC77 AEAWF T10TOLERANCE IN PERCENT,CAPACITANCE CAPACITANCE TOLERANCE IN PERCENT THE LIMITS OF PERMISSIBLE PERCENT DEVIATION OF CAPACITANCE VALUE OF AN ITEM FROM ITS RATED VALUE. 1F MODE REPLY 0 AEAXH /D/ 19CURRENT FOR WHICH DESIGNED,CIRCUIT CIRCUIT CURRENT FOR WHICH DESIGNED THE TYPE OF ELECRICAL CIRCUIT IN WHICH THE ITEM IS DESIGNED TO BE USED. 2D MODE REPLY 21AB621AC81 AEAYB /D/ 10VOLTAGE RATING IN VOLTS,CONTINUOUS,NONDERATED NONDERATED CONTINUOUS VOLTAGE RATING IN VOLTS THE HIGHEST POTENTIAL THAT MAY BE CONTINUOUSLY APPLIED TO THE ITEM,AT THE HIGHEST TEMPERATURE WITHOUT VOLTAGE DERATING. 1B MODE REPLY 0 AEAZB /D/ 10VOLTAGE RATING IN VOLTS,CONTINUOUS,DERATED DERATED CONTINUOUS VOLTAGE RATING IN VOLTS THE HIGHEST POTENTIAL THAT MAY BE CONTINUOUSLY APPLIED TO THE ITEM,AT ITS MAXIMUM OPERATING TEMPERATURE. 1B MODE REPLY 0 AEBAB /D/ 10VOLTAGE RATING IN DC VOLTS,SURGE,NONDERATED NONDERATED SURGE VOLTAGE RATING IN DC VOLTS THE HIGHEST PERMISSIBLE LEVEL OF A SPORADIC OR INTERMITTENT DIRECT CURRENT POTENTIAL TO WHICH THE ITEM MAY BE SUBJECTED WITHOUT DAMAGE OR LOSS OF FUNCTION,AT THE HIGHEST TEMPERATURE WITHOUT VOLTAGE DERATING. 1B MODE REPLY 0 AEBBB /D/ 10VOLTAGE RATING IN DC VOLTS,SURGE,DERATED DERATED SURGE VOLTAGE RATING IN DC VOLTS THE HIGHEST PERMISSIBLE LEVEL OF A SPORADIC OR INTERMITTENT DIRECT CURRENT POTENTIAL TO WHICH THE ITEM MAY BE SUBJECTED WITHOUT DAMAGE OR LOSS OF FUNCTION AT ITS MAXIMUM OPERATING TEMPERATURE. 1B MODE REPLY 0 AEBCB 10COEFFICIENT OF CAPACITANCE IN PPM PER DEG CELSIUS,TEMP TEMP COEFFICIENT OF CAPACITANCE IN PPM PER DEG CELSIUS A CONSTANT THAT REPRESENTS THE PROPORTIONATE CHANGE IN CAPACITANCE CAUSED BY A CHANGE IN TEMPERATURE,EXPRESSED IN PARTS PER MILLION PER DEGREE CELSIUS. 1B MODE REPLY 0 AEBDF T10TOLERANCE OF TEMP COEFFICIENT IN PPM PER DEG CELSIUS TOLERANCE OF TEMP COEFFICIENT IN PPM PER DEG CELSIUS THE LIMITS OF PERMISSIBLE DEVIATION OF THE TEMPERATURE COEFFICIENT FROM THE RATED VALUE,EXPRESSED IN PARTS PER MILLION PER DEGREE CELSIUS. 1F MODE REPLY 0 AEBEJ /D/T10LIMITS IN PERCENT CAPACITANCE CHANGE,TEMP,VOLTAGE VOLTAGE TEMP LIMITS IN PERCENT CAPACITANCE CHANGE THE MAXIMUM PERMISSIBLE CAPACITANCE CHANGE WITH TEMPERATURE OVER THE OPERATING TEMPERATURE RANGE,MEASURED EITHER WITH OR WITHOUT RATED VOLTAGE APPLIED. 1D AND 1F MODE REPLY11AC78 AEBFF T10COEFFICIENT OF CAPACITANCE RANGE IN PPM PER DEG CELSIUS,TEMP TEMP COEFFICIENT OF CAPACITANCE RANGE IN PPM PER DEG CELSIUS THE MINIMUM AND MAXIMUM VALUES OF THE PERMISSIBLE CHANGE IN CAPACITANCE CAUSED BY A CHANGE IN TEMPERATURE,IN PARTS PER MILLION PER DEGREE CELSIUS. 1F MODE REPLY 0 AEBGJ /D/ 10TEMP,OPERATING,NONDERATED NONDERATED OPERATING TEMP THE LIMITS OF TEMPERATURE WITHIN WHICH THE ITEM MAY BE OPERATED WITHOUT VOLTAGE DERATING. 1D AND 1B MODE REPLY11AB36 AEBHJ /D/ 10TEMP AT WHICH DERATED VOLTAGE RATINGS APPLY,MAXIMUM MAXIMUM TEMP AT WHICH DERATED VOLTAGE RATINGS APPLY THE HIGHEST TEMPERATURE AT WHICH THE ITEM MAY BE OPERATED AT REDUCED VOLTAGE RATING. 1D AND 1B MODE REPLY11AB36 AEBJB 10CURRENT RATING IN AMPS,CONTINUOUS CONTINUOUS CURRENT RATING IN AMPS THE MAXIMUM DIRECT CURRENT,OR ROOT MEAN SQUARE CURRENT AT RATED FREQUENCY,THAT AN ITEM WILL CARRY CONTINUOUSLY. 1B MODE REPLY 0 AEBKB 10CURRENT RATING AT HIGHEST FREQUENCY IN RMS AMPS,RF,MAXIMUM MAXIMUM RF CURRENT RATING AT HIGHEST RATED FREQUENCY IN RMS AMPS THE MAXIMUM ALTERNATING CURRENT THAT MAY FLOW THROUGH THE ITEM AT THE HIGHEST FREQUENCY ABOVE THREE KILOHERTZ. 1B MODE REPLY 0 AEBLB 10FREQUENCY AT WHICH RF CURRENT RATING APPLIES IN KILOHERTZ,HIGHEST HIGHEST FREQUENCY AT WHICH RF CURRENT RATING APPLIES IN KILOHERTZ THE MAXIMUM FREQUENCY,HIGHER THAN THREE KILOHERTZ,AT WHICH A MAXIMUM ALTERNATING CURRENT RATING HAS BEEN ESTABLISHED. 1B MODE REPLY 0 AEBMB 10CURRENT RATING AT LOWEST RATED FREQUENCY IN RMS AMPS,RF,MAXIMUM MAXIMUM RF CURRENT RATING AT LOWEST RATED FREQUENCY IN RMS AMPS THE MAXIMUM ALTERNATING CURRENT THAT MAY FLOW THROUGH THE ITEM AT THE LOWEST FREQUENCY ABOVE THREE KILOHERTZ. 1B MODE REPLY 0 AEBNB 10FREQUENCY AT WHICH RF CURRENT RATING APPLIES IN KILOHERTZ,LOWEST LOWEST FREQUENCY AT WHICH RF CURRENT RATING APPLIES IN KILOHERTZ THE MINIMUM FREQUENCY,HIGHER THAN THREE KILOHERTZ,AT WHICH A MAXIMUM ALTERNATING CURRENT RATING HAS BEEN ESTABLISHED. 1B MODE REPLY 0 AEBPJ 04DISTANCE BETWEEN TERMINALS PARALLEL TO LENGTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO LENGTH THE CENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO THE LENGTH OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 AEBQJ 04DISTANCE BETWEEN TERMINALS PARALLEL TO WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO WIDTH THE CENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO THE WIDTH OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 AEBRJ 04DISTANCE BETWEEN TERMINALS PARALLEL TO HEIGHT,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO HEIGHT THE CENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO THE HEIGHT OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 AEBSJ 04DISTANCE BETWEEN TERMINALS PARALLEL TO DIAMETER,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO DIAMETER THE CENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO THE DIAMETER OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 AEBTJ 04DIAMETER,TERMINAL TERMINAL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A TERMINAL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AEBUJ 04HEIGHT FROM BODY,TERMINAL TERMINAL HEIGHT FROM BODY THE DISTANCE FROM THE END OF THE TERMINAL TO THE BODY OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 AEBVJ 04DIAMETER,HOLE,MOUNTING,UNTHREADED UNTHREADED MOUNTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AEBWJ 04DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO HEIGHT,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO HEIGHT THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AEBXJ 04DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO DIAMETER,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO DIAMETER THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE DIAMETER. 2D AND 1B MODE REPLY21AA051AC20 AEBYJ 04DISTANCE BETWEEN CENTERLINES OF MOUNTING FACILITIES PARALLEL TO BODY LENGTH DISTANCE BETWEEN CENTERLINES OF MOUNTING FACILITIES PARALLEL TO BODY LENGTH THE DISTANCE BETWEEN CENTERLINES OF MOUNTING FACILITIES PARALLEL TO THE LENGTH OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 AEBZL 03DESIGNATOR,DIAGRAM,SCHEMATIC SCHEMATIC DIAGRAM DESIGNATOR A DESIGNATOR INDICATING A GRAPHIC REPRESENTATION,IN STANDARD AND ACCEPTED SYMBOLS,OF ESSENTIAL ELECTRICAL-ELECTRONIC ELEMENTS AND RELATED CONNECTIONS ON THE ITEM. 1L MODE REPLY 0 AECAD /D/ 09MATERIAL,INSULATION,CASE CASE INSULATION MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CASE INSULATION IS FABRICATED. SELECT REPLY CODE 10AD09 AECBD /D/ 07SEALED,HERMETICALLY HERMETICALLY SEALED AN INDICATION OF WHETHER OR NOT THE ITEM HAS A SEAL,ACCOMPLISHED BY MATERIAL FUSION,WELDING,BRAZING,OR SOLDERING,OF CERAMIC,GLASS,METAL,OR COMBINATIONS THEREOF,TO PREVENT THE PASSAGE OF MOISTURE OR GASES THROUGH THE SEAL. SELECT REPLY CODE 10AA89 AECCD /D/ 07CASE,MAGNETIC MAGNETIC CASE AN INDICATION OF WHETHER OR NOT THE MATERIAL OF THE CASE HAS THE CAPABILITY OF BEING MAGNETIZED. SELECT REPLY CODE 10AA89 AECDD /D/ 09MATERIAL,ELECTRODE,CAPACITIVE CAPACITIVE ELECTRODE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CAPACITIVE ELECTRODE IS FABRICATED. SELECT REPLY CODE 10AD09 AECED 18TYPE,ANODE ANODE TYPE THE GENERAL CONSTRUCTION AND/OR FORM OF THE ANODE MATERIAL. SELECT REPLY CODE 10AC79 AECFB /D/ 10RESISTANCE AT 25 DEG CELSIUS IN OHMS,SERIES,EQUIVALENT EQUIVALENT SERIES RESISTANCE AT 25 DEG CELSIUS IN OHMS ALL INTERNAL SERIES RESISTANCES CONCENTRATED OR LUMPED AT ONE POINT IN THE CIRCUIT AND TREATED AS ONE RESISTANCE,EXPRESSED AT 25 DEGREES CELSIUS. 1B MODE REPLY 0 AECGJ /D/ 10RESISTANCE AT 25 DEG CELSIUS,INSULATION INSULATION RESISTANCE AT 25 DEG CELSIUS THE DIRECT CURRENT RESISTANCE BETWEEN TWO CONDUCTORS THAT ARE SEPARATED BY AN INSULATING MATERIAL,EXPRESSED AT 25 DEGREES CELSIUS. 2D AND 1B MODE REPLY21AA571AC77 AECHJ /D/ 10RESISTANCE AT MAX OPERATING TEMP,INSULATION INSULATION RESISTANCE AT MAX OPERATING TEMP DIRECT CURRENT RESISTANCE BETWEEN TWO CONDUCTORS THAT ARE SEPARATED BY AN INSULATING MATERIAL,MEASURED AT THE MAXIMUM OPERATING TEMPERATURE OF THE ITEM. 2D AND 1B MODE REPLY21AA571AC77 AECJB 10FACTOR AT 25 DEG CELSIUS,QUALITY QUALITY FACTOR AT 25 DEG CELSIUS THE RATIO OF CAPACITIVE REACTANCE TO RESISTANCE,EXPRESSED AT 25 DEGREES CELSIUS. 1B MODE REPLY 0 AECKB 10FACTOR AT 25 DEG CELSIUS IN PERCENT,DISSIPATION DISSIPATION FACTOR AT 25 DEG CELSIUS IN PERCENT THE RATIO OF THE RESISTANCE TO CAPACITIVE REACTANCE,EXPRESSED AT 25 DEGREES CELSIUS IN PERCENT. 1B MODE REPLY 0 AECLJ /D/ 10LEAKAGE AT 25 DEG CELSIUS,CURRENT,DIRECT DIRECT CURRENT LEAKAGE AT 25 DEG CELSIUS STRAY DIRECT CURRENT OF RELATIVELY SMALL VALUE WHICH FLOWS THROUGH THE CAPACITOR WHEN VOLTAGE IS IMPRESSED ACROSS IT,EXPRESSED AT 25 DEGREES CELSIUS. 1D AND 1B MODE REPLY11AC30 AECMJ /D/ 10LEAKAGE AT MAX OPERATING TEMP,CURRENT,DIRECT DIRECT CURRENT LEAKAGE AT MAX OPERATING TEMP STRAY DIRECT CURRENT OF RELATIVELY SMALL VALUE WHICH FLOWS THROUGH THE CAPACITOR WHEN VOLTAGE IS IMPRESSED ACROSS IT,EXPRESSED AT THE MAXIMUM OPERATING TEMPERATURE. 1D AND 1B MODE REPLY11AC30 AECNB 10IMPEDANCE AT MINIMUM OPERATING TEMP IN OHMS IMPEDANCE AT MINIMUM OPERATING TEMP IN OHMS THE TOTAL OPPOSITION OFFERED TO THE FLOW OF AN ALTERNATING OR PULSATING CURRENT,EXPRESSED AT MINIMUM OPERATING TEMPERATURE IN OHMS. 1B MODE REPLY 0 AECPB /D/ 10FACTOR AT 25 DEG CELSIUS IN PERCENT,POWER POWER FACTOR AT 25 DEG CELSIUS IN PERCENT THE RATIO OF RESISTANCE TO IMPEDANCE,EXPRESSED AT 25 DEGREES CELSIUS IN PERCENT. 1B MODE REPLY 0 AECQD 10POLARIZATION,ELECTRICAL ELECTRICAL POLARIZATION AN INDICATION OF WHETHER OR NOT THE ITEM NORMALLY WILL ACCEPT FLOW OF CURRENT IN ONE DIRECTION ONLY. SELECT REPLY CODE 10AC80 AECRF T10RANGE IN HERTZ,RESISTANCE,VIBRATION VIBRATION RESISTANCE RANGE IN HERTZ THE LOW AND HIGH FREQUENCIES OF VIBRATORY MOTION AND MECHANICAL STRESSES BETWEEN WHICH THE ITEM IS TESTED,OR OPERATED,WITHOUT DELETERIOUS EFFECT ON ITS ELECTRICAL OR MECHANICAL CHARACTERISTICS,EXPRESSED IN HERTZ. 1F MODE REPLY 0 AECSA 12QUANTITY,HOLE,BOLT BOLT HOLE QUANTITY THE NUMBER OF BOLT HOLES PROVIDED ON THE ITEM. 1A MODE REPLY 0 AECTJ 04THREAD DEPTH THREAD DEPTH A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING IMCOMPLETE THREADS,ALONG A LINE PERPENDICULAR TO THE DIAMETER OF AN INTERNAL THREAD. 2D AND 1B MODE REPLY21AA051AC20 AECUJ /D/ 04WIDTH,PLATE,TOP TOP PLATE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH ALONG THE TOP PLATE, IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AECVB /D/ 10VARIATION BETWEEN RESISTOR SECTIONS IN DEG,PHASING PHASING VARIATION BETWEEN RESISTOR SECTIONS IN DEG THE PERMISSIBLE VARIATION BETWEEN RELATIVE ALIGNMENTS OF THE SECTIONS OF A MULTISECTION RESISTOR WITH RESPECT TO THE POSITION OF THE WIPERS ON THEIR RESPECTIVE ELECTRICAL ELEMENTS,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AECWJ 04DIAMETER,BODY BODY DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR BODY,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AECXJ /D/ 04DIAMETER,PILOT PILOT DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AECYJ /D/ 04LENGTH,PILOT PILOT LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AECZJ 04DIAMETER,LIP,MOUNTING MOUNTING LIP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AEDAJ 04DEPTH,LIP,MOUNTING MOUNTING LIP DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEDBJ /D/ 04DIAMETER,UNDERCUT UNDERCUT DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AEDCJ 04WIDTH,UNDERCUT,SHAFT SHAFT UNDERCUT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEDDJ /D/ 04LENGTH,STUD,MOUNTING MOUNTING STUD LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AEDEJ /D/ 04DIAMETER,CIRCLE,HOLE/STUD,MOUNTING MOUNTING HOLE/STUD CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AEDFJ /D/ 04WIDTH,UNDERCUT,SECOND SECOND UNDERCUT WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AEDGJ 04WIDTH,CHANNEL CHANNEL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CHANNEL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AEDHJ 04LENGTH,CHANNEL CHANNEL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEDJJ /D/ 04LENGTH,SHAFT SHAFT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SHAFT,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AEDKJ /D/ 04DIAMETER,SHAFT SHAFT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHAFT,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AEDLJ /D/ 04LENGTH,FLAT,FIRST FIRST FLAT LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AEDMJ /D/ 04HEIGHT,FLAT FLAT HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 AEDNJ 04LENGTH,TIP TIP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TIP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AEDPJ /D/ 04LENGTH,FLAT,SECOND SECOND FLAT LENGTH NONE. 1D AND 1B MODE REPLY11AA05 AEDQJ /D/ 04DIAMETER,UNDERCUT UNDERCUT DIAMETER NONE. PLEASE USE MRC ABPA IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 AEDRJ 04WIDTH,UNDERCUT UNDERCUT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN UNDERCUT,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AEDSJ 04WIDTH,SHAFT,SQUARE SQUARE SHAFT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEDTJ /D/ 04DIAMETER,UNDERCUT,SECOND SECOND UNDERCUT DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AEDUJ /D/ 04THICKNESS,MINOR,TAPER TAPER MINOR THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AEDVJ /D/ 04THICKNESS,MAJOR,TAPER TAPER MAJOR THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AEDWJ /D/ 04DEPTH,CHANNEL CHANNEL DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEDXL 16STYLE,SHAFT SHAFT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SHAFT. 1L MODE REPLY 0 AEDYD /D/ 07MATERIAL,SHAFT,METALLIC METALLIC SHAFT MATERIAL INDICATES WHETHER OR NOT THE SHAFT IS COMPOSED OF METAL. SELECT REPLY CODE 10AA89 AEDZD /D/ 18TYPE,BEARING,SHAFT SHAFT BEARING TYPE INDICATES THE TYPE OF SHAFT BEARING/S/ FURNISHED. SELECT REPLY CODE 10AB81 AEEAD 18TYPE,SWITCH SWITCH TYPE INDICATES THE TYPE OF SWITCH INCLUDED IN THE ITEM. SELECT REPLY CODE 10AC82 AEEBB /D/ 10CURRENT RATING IN AMPS,SWITCH SWITCH CURRENT RATING IN AMPS THE ELECTRICAL CURRENT CAPACITY OF THE SWITCH,SPECIFIED FOR NORMAL OPERATION,EXPRESSED IN AMPERES. 1B MODE REPLY 0 AEECD 18TYPE,CURRENT,SWITCH SWITCH CURRENT TYPE INDICATES THE TYPE OF ELECTRICAL CURRENT FOR WHICH THE SWITCH IS DESIGNED TO OPERATE. SELECT REPLY CODE 10AB62 AEEDB 10VOLTAGE RATING IN VOLTS,SWITCH SWITCH VOLTAGE RATING IN VOLTS THE VOLTAGE FOR WHICH THE SWITCH IS RATED FOR NORMAL OPERATION,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AEEEA 19CODE,MANUFACTURER,CONNECTOR CONNECTOR MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE ELECTRICAL CONNECTOR RECEPTACLE. 1A MODE REPLY 0 AEEFA 19NUMBER,PART,CONNECTOR MANUFACTURER CONNECTOR MANUFACTURER PART NUMBER THE IDENTIFYING PART NUMBER ASSIGNED TO THE ELECTRICAL CONNECTOR RECEPTACLE. 1A MODE REPLY 0 AEEGD /D/ 08LOCATION,TERMINAL TERMINAL LOCATION INDICATES THE LOCATION OF THE TERMINAL(S) FOR MAKING CONNECTION TO AN ITEM. PLEASE USE MRC CQTM IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AE46 AEEHD /D/ 11METHOD,INCLOSURE,RESISTIVE ELEMENT RESISTIVE ELEMENT INCLOSURE METHOD THE MEANS PROVIDED TO COAT,COVER,OR PROTECT THE RESISTIVE ELEMENT. SELECT REPLY CODE 10AF90 AEEJA /D/ 10LIFE IN CYCLES,ROTATIONAL,DESIGNED DESIGNED ROTATIONAL LIFE IN CYCLES THE NUMBER OF CYCLES THROUGH WHICH THE ACTUATING DEVICE OF AN ITEM IS DESIGNED TO OPERATE WITHOUT DETERIORATION. 1A MODE REPLY 0 AEEKB /D/ 10RESISTANCE IN OHMS,NOISE,EQUIVALENT EQUIVALENT NOISE RESISTANCE IN OHMS THE TRANSIENT RESISTANCE APPEARING BETWEEN THE CONTACT AND THE RESISTANCE ELEMENT WHEN THE SHAFT IS ROTATED OR TRANSLATED,EXPRESSED IN OHMS. 1B MODE REPLY 0 AEELB /D/ 10VARIATION BETWEEN RESISTOR SECTIONS IN OHMS,PHASING PHASING VARIATION BETWEEN RESISTOR SECTIONS IN OHMS THE PERMISSIBLE VARIATION BETWEEN RELATIVE ALIGNMENTS OF THE SECTIONS OF A MULTISECTION RESISTOR WITH RESPECT TO THE POSITION OF THE WIPERS ON THEIR RESPECTIVE ELECTRICAL ELEMENTS,EXPRESSED IN OHMS. 1B MODE REPLY 0 AEEMB /D/ 10RESISTANCE IN OHMS,MINIMUM MINIMUM RESISTANCE IN OHMS THE RESISTANCE MEASURED BETWEEN THE WIPER TERMINAL AND ANY TERMINAL WITH THE SHAFT POSITIONED TO GIVE A MINIMUM VALUE,EXPRESSED IN OHMS. 1B MODE REPLY 0 AEENB /D/ 10RESISTANCE IN OHMS,END END RESISTANCE IN OHMS THE RESISTANCE MEASURED BETWEEN THE WIPER TERMINAL AND AN END TERMINAL WITH THE SHAFT POSITIONED AT THE CORRESPONDING END POINT,EXPRESSED IN OHMS. 1B MODE REPLY 0 AEEPB /D/ 10VOLTAGE IN PERCENT OF TOTAL APPLIED VOLTAGE,MINIMUM MINIMUM VOLTAGE IN PERCENT OF TOTAL APPLIED VOLTAGE THE LOWEST VOLTAGE BETWEEN THE WIPER TERMINAL AND AN END TERMINAL WHEN THE SHAFT IS POSITIONED NEAR THE CORRESPONDING END OF ELECTRICAL CONTINUITY TRAVEL. 1B MODE REPLY 0 AEEQB /D/ 10VOLTAGE IN PERCENT OF TOTAL APPLIED VOLTAGE,END END VOLTAGE IN PERCENT OF TOTAL APPLIED VOLTAGE THE VOLTAGE BETWEEN THE WIPER TERMINAL AND AN END TERMINAL WHEN THE SHAFT IS POSITIONED AT THE CORRESPONDING END POINT FOR WIRE WOUND ITEMS AND AT THE THEORETICAL END POINT FOR NONWIRE WOUND ITEMS ONLY. 1B MODE REPLY 0 AEERF /D/T10COEFFICIENT OF RESISTANCE WIRE IN PPM PER DEG CELSIUS,TEMP TEMP COEFFICIENT OF RESISTANCE WIRE IN PPM PER DEG CELSIUS A CONSTANT THAT REPRESENTS THE PROPORTIONATE CHANGE IN RESISTANCE OF THE WIRE OF WHICH THE RESISTANCE ELEMENT OF A RESISTOR IS WOUND,EXPRESSED IN PARTS PER MILLION PER DEG CELSIUS. 1F MODE REPLY 0 AEESA /D/ 10CURVE,TAPER,STANDARD STANDARD TAPER CURVE THE RATE OF CHANGE AND DISTRIBUTION OF RESISTANCE,IN RELATION TO THE ROTATION OF THE CONTROL SHAFT,WHICH ESTABLISHES A STANDARD TAPER CURVE DESIGNATED BY AN ALPHABETIC CHARACTER AND IS ACCEPTED FOR COMMON USAGE. 1A MODE REPLY 0 AEETJ /D/ 10CURVE AT SPECIFIC PERCENT RESISTANCE CHANGE,TAPER,NONSTANDARD NONSTANDARD TAPER CURVE AT SPECIFIC PERCENT RESISTANCE CHANGE THE RATE OF CHANGE AND DISTRIBUTION OF RESISTANCE,IN RELATION TO THE ROTATION OF THE CONTROL SHAFT OF A VARIABLE RESISTOR,THAT ESTABLISHES A CURVE THAT CANNOT BE IDENTIFIED TO A STANDARD TAPER CURVE. 2D AND 1B MODE REPLY21AC831AC84 AEEUJ /D/ 04THICKNESS,PLATE,TOP TOP PLATE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE TOP PLATE,IN DISTINCTION F ROM THE LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AEEVA /D/ 12QUANTITY,HOLE,MOUNTING,FIRST SURFACE FIRST SURFACE MOUNTING HOLE QUANTITY THE NUMBER OF MOUNTING HOLES PROVIDED IN THE FIRST SURFACE. 1A MODE REPLY 0 AEEWD /D/ 19CHARACTERISTIC,FUNCTION FUNCTION CHARACTERISTIC THE SPECIFIED MATHEMATICAL RELATION BETWEEN THE TERMINAL RESISTANCE,OR OUTPUT RATIO,AND THE ROTATION OF THE ACTUATOR. SELECT REPLY CODE 10AC85 AEEXF /D/T10TOLERANCE,CONFORMITY,FUNCTION FUNCTION CONFORMITY TOLERANCE THE PERMISSIBLE RANGE BY WHICH THE ACTUAL VALUE OF RESISTANCE OF VOLTAGE AT ANY SPECIFIED POINT MAY DEVIATE FROM THE THEORETICAL VALUE FOR THE LINEAR OR NONLINEAR FUNCTION,EXPRESSED AS A MINUS AND PLUS PERCENT. 1F MODE REPLY 0 AEEYD /D/ 19CONFORMITY,FUNCTION,LINEAR LINEAR FUNCTION CONFORMITY THE FIDELITY OF THE RELATIONSHIP BETWEEN THE ACTUAL FUNCTION CHARACTERISTIC AND THE THEORETICAL FUNCTION. SELECT REPLY CODE 10AC86 AEEZD 19POSITION,OFF,CONTACT ARM ELECTRICAL CONTACT ARM ELECTRICAL OFF POSITION THE LOCATION OF THE CONTACT ARM WHEN THERE IS NO ELECTRICAL CONTINUITY BETWEEN THE MOVING CONTACT AND THE RESISTIVE ELEMENT. SELECT REPLY CODE 10AC87 AEFAD /D/ 19STATUS,ELECTRICAL,CONTACT ARM CONTACT ARM ELECTRICAL STATUS AN INDICATION THAT EITHER THE MOVING CONTACT IS INSULATED FROM THE OPERATING SHAFT,THE MOUNTING FACILITY,FRAME,OR CASE,OR IS GROUNDED TO THE SHAFT,MOUNTING FACILITY,FRAME,OR CASE. SELECT REPLY CODE 10AC88 AEFBJ 10DISSIPATION RATING IN WATTS,POWER POWER DISSIPATION RATING IN WATTS THE MAXIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY AN ITEM,EXPRESSED IN WATTS. 1D AND 1B MODE REPLY11AC89 AEFCJ /D/T10TEMP CHARACTERISTIC RANGE IN PERCENT,RESISTANCE RESISTANCE TEMP CHARACTERISTIC RANGE IN PERCENT THE CHANGE IN TOTAL RESISTANCE OVER A SPECIFIED TEMPERATURE RANGE,EXPRESSED AS A PERCENT OF THE TOTAL RESISTANCE AT A SPECIFIED REFERENCE TEMPERATURE. 1D AND 1F MODE REPLY12AC90 AEFDD 18TYPE,ACTUATOR ACTUATOR TYPE INDICATES THE TYPE OF FACILITY OR ARRANGEMENT PROVIDED FOR MOVING THE VARIABLE CONTACT(S). SELECT REPLY CODE 10AC91 AEFED /D/ 18TYPE,COUPLING COUPLING TYPE THE SHAFT FEATURE OF THE ITEM WHICH AFFORDS A DRIVE CONNECTION TO THE ADJACENT SECTION OF A MULTISECTION ITEM. SELECT REPLY CODE 10AC92 AEFFJ /D/ 10TRAVEL IN ANGULAR DEG,ACTUATOR,ROTARY ROTARY ACTUATOR TRAVEL IN ANGULAR DEG THE MEASUREMENT OF THE ROTARY MECHANICAL MOTION OF THE ACTUATING SHAFT OF AN ITEM,EXPRESSED IN ANGULAR DEGREES. 2D AND 1B MODE REPLY21AC931AC20 AEFGJ /D/ 04DIAMETER,HOLE,MOUNTING,FIRST SURFACE FIRST SURFACE MOUNTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE ON THE FIRST SURFACE, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AEFHJ 10ROTATION IN DEG ANGULAR ROTATION,ELECTRICAL,EFFECTIVE EFFECTIVE ELECTRICAL ROTATION IN DEG ANGULAR ROTATION THAT PART OF THE TOTAL ROTATIONAL TRAVEL OF THE ACTUATOR THAT PRODUCES A CHANGE IN OUTPUT,EXPRESSED IN DEGREE ANGULAR ROTATION. 1D AND 1B MODE REPLY11AC20 AEFJJ /D/ 10OVERTRAVEL IN DEG ANGULAR ROTATION,ELECTRICAL,ROTARY ACTUATION ROTARY ACTUATION ELECTRICAL OVERTRAVEL IN DEG ANGULAR ROTATION THE MEASURE OF ROTARY TRAVEL AT THE START AND/OR END OF THE RESISTIVE ELEMENT,DURING WHICH ELECTRICAL CONTINUITY BETWEEN THE WIPER TERMINAL AND THE RESISTIVE ELEMENT IS MAINTAINED WITH NO CHANGE IN OUTPUT,EXPRESSED IN DEGREE ANGULAR ROTATION. 1D AND 1B MODE REPLY11AC94 AEFKJ 10TORQUE,STARTING,MAXIMUM MAXIMUM STARTING TORQUE THE MAXIMUM AMOUNT OF TURNING FORCE REQUIRED TO INITIATE THE ACTUATOR MOVEMENT. 1D AND 1B MODE REPLY11AA56 AEFLJ 10TORQUE,RUNNING,MAXIMUM MAXIMUM RUNNING TORQUE THE MAXIMUM AMOUNT OF FORCE REQURED TO MAINTAIN ACTUATOR MOVEMENT. 1D AND 1B MODE REPLY11AA56 AEFMJ 10TORQUE,STOP,MAXIMUM MAXIMUM STOP TORQUE THE MAXIMUM AMOUNT OF TURNING FORCE THAT CAN BE APPLIED THROUGH THE OPERATING SHAFT WITH0UT DAMAGE TO THE STOPS. 1D AND 1B MODE REPLY11AA56 AEFND /D/ 08LOCATION,DEVICE,NONTURN NONTURN DEVICE LOCATION INDICATES THE LOCATION OF A MECHANICAL DEVICE WHICH PREVENTS THE TURNING OF THE ITEM ON ITS MOUNTED SURFACE,EXPRESSED BY THE TWELVE HOUR CLOCK DESIGNATION. PLEASE USE MRC CQPH WITH ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AC95 AEFPJ 04RADIUS,DEVICE,NONTURN NONTURN DEVICE RADIUS THE LINEAR MEASUREMENT OF THE DISTANCE FROM THE ACTUATOR CENTERLINE TO THE CENTERLINE OF THE NONTURN DEVICE. 2D AND 1B MODE REPLY21AA051AC20 AEFQJ 04LENGTH,DEVICE,NONTURN NONTURN DEVICE LENGTH THE MEASUREMENT OF THE DISTANCE THAT THE NONTURN DEVICE PROTRUDES ABOVE THE MOUNTING SURFACE. 2D AND 1B MODE REPLY21AA051AC20 AEFRJ 04WIDTH,DEVICE,NONTURN NONTURN DEVICE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A NONTURN DEVICE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AEFSJ 04DIAMETER,DEVICE,NONTURN NONTURN DEVICE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A NONTURN DEVICE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AEFTJ 10TRAVEL,ACTUATOR,LONGITUDINAL LONGITUDINAL ACTUATOR TRAVEL THE MEASUREMENT OF THE LINEAR MECHANICAL MOTION OF THE ACUTATING SHAFT OF AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 AEFUJ /D/ 10FORCE,OPERATING,MAXIMUM,LONGITUDINAL ACTUATOR LONGITUDINAL ACTUATOR MAXIMUM OPERATING FORCE THE MAXIMUM AMOUNT OF FORCE REQUIRED TO INITIATE MOVEMENT OF A LONGITUDINAL TYPE ACTUATOR. 1D AND 1B MODE REPLY11AC96 AEFVJ /D/ 10FORCE,STOP,MAXIMUM,LONGITUDINAL ACTUATOR LONGITUDINAL ACTUATOR MAXIMUM STOP FORCE THE MAXIMUM AMOUNT OF FORCE THAT CAN BE APPLIED THROUGH THE OPERATING SHAFT WITHOUT DAMAGE TO THE STOPS. 1D AND 1B MODE REPLY11AB18 AEFWJ 04LENGTH,STROKE,EFFECTIVE ELECTRICAL,LONGITUDINAL ACTUATOR LONGITUDINAL ACTUATOR EFFECTIVE ELECTRICAL STROKE LENGTH THE PART OF THE TOTAL LONGITUDINAL TRAVEL OF THE ACTUATOR THAT PRODUCES A CHANGE IN OUTPUT. 2D AND 1B MODE REPLY21AA051AC20 AEFXJ /D/ 10OVERTRAVEL,ELECTRICAL,LONGITUDINAL ACTUATOR LONGITUDINAL ACTUATOR ELECTRICAL OVERTRAVEL THE MEASURE OF LONGITUDINAL TRAVEL AT THE START AND/OR END OF THE RESISTIVE ELEMENT,DURING WHICH ELECTRICAL CONTINUITY BETWEEN THE WIPER TERMINAL AND THE RESISTIVE ELEMENT IS MAINTAINED WITH NO CHANGE IN OUTPUT. 2D AND 1B MODE REPLY21AA053AE46 AEFYJ 10PLAY,END,SHAFT SHAFT END PLAY THE TOTAL AXIAL EXCURSION OF THE SHAFT MEASURED AT THE END OF THE SHAFT WITH A SPECIFIED AXIAL LOAD APPLIED ALTERNATELY IN THE OPPOSITE DIRECTIONS. 1D AND 1B MODE REPLY11AA05 AEFZJ 10RUNOUT,SHAFT SHAFT RUNOUT THE ECCENTRICITY OF THE SHAFT DIAMETER WITH RESPECT TO THE ROTATIONAL AXIS OF THE SHAFT,MEASURED AT A SPECIFIED DISTANCE FROM THE END OF THE SHAFT,WHEN THE BODY OF THE ITEM IS HELD FIXED AND THE SHAFT IS ROTATED WITH A SPECIFIED LOAD APPLIED RADIALLY TO THE SHAFT. 1D AND 1B MODE REPLY11AA05 AEGAJ 10RUNOUT,LATERAL LATERAL RUNOUT THE PERPENDICULARITY OF THE MOUNTING SURFACE,WITH RESPECT TO THE ROTATIONAL AXIS OF THE SHAFT,AND MEASURED ON THE MOUNTING SURFACE AT A SPECIFIED DISTANCE FROM THE OUTSIDE EDGE OF THE MOUNTING SURFACE,WHEN THE SHAFT IS HELD FIXED AND THE BODY OF THE ITEM IS ROTATED WITH SPECIFIED LOADS APPLIED RADIALLY AND AXIALLY TO THE BODY OF THE ITEM. 1D AND 1B MODE REPLY11AA05 AEGBJ 10RUNOUT,DIAMETER,PILOT PILOT DIAMETER RUNOUT THE ECCENTRICITY OF THE PILOT DIAMETER WITH RESPECT TO THE ROTATIONAL AXIS OF THE SHAFT AND MEASURED ON THE PILOT DIAMETER WHEN THE SHAFT IS HELD AND THE BODY OF THE ITEM IS ROTATED WHILE A SPECIFIED LOAD IS APPLIED RADIALLY TO THE BODY. 1D AND 1B MODE REPLY11AA05 AEGCJ 10PLAY,RADIAL,SHAFT SHAFT RADIAL PLAY THE TOTAL RADIAL EXCURSION OF THE SHAFT MEASURED AT A SPECIFIED DISTANCE FROM THE FRONT SURFACE OF THE UNIT WITH A SPECIFIED RADIAL LOAD APPLIED ALTERNATELY IN OPPOSITE DIRECTIONS AT A SPECIFIED POINT. 1D AND 1B MODE REPLY11AA05 AEGDB 10BACKLASH IN DEG ANGULAR ROTATION,MECHANICAL MECHANICAL BACKLASH IN DEG ANGULAR ROTATION THE MAXIMUM DIFFERENCE OF SHAFT POSITION THAT OCCURS WHEN THE SHAFT IS MOVED TO THE SAME ACTUAL OUTPUT RATIO POINT FROM OPPOSITE DIRECTIONS,EXPRESSED IN DEGREE ANGULAR ROTATION. 1B MODE REPLY 0 AEGEA /D/ 12QUANTITY,HOLE,MOUNTING,SECOND SURFACE SECOND SURFACE MOUNTING HOLE QUANTITY THE NUMBER OF MOUNTING HOLES PROVIDED IN THE SECOND SURFACE. 1A MODE REPLY 0 AEGFJ /D/ 04DIAMETER,HOLE,MOUNTING,SECOND SURFACE SECOND SURFACE MOUNTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE ON THE SECOND SURFACE, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AEGGA 03DESIGNATOR,IDENTIFICATION,NEXT HIGHER ASSEMBLY NEXT HIGHER ASSEMBLY IDENTIFICATION DESIGNATOR THE NAME OR COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH IDENTIFY THE SPECIFIC NEXT HIGHER ASSEMBLY. 1A MODE REPLY 0 AEGHD /D/ 19POSITION,OPERATING,SWITCH SWITCH OPERATING POSITION THE DEFINITIVE POSITIONAL POINT AT WHICH THE SWITCH OPERATES /STARTING WITH THE ACTUATOR IN EXTREME COUNTERCLOCKWISE POSITION AND MOVING CLOCKWISE FOR ROTARY ACTUATED RESISTORS;STARTING WITH ACTUATOR FULL RETRACTED /PUSHED IN/ FOR LONGITUDINALLY ACTUATED RESISTORS/. PLEASE USE MRC ARNH IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AC97 AEGJD 19ARRANGEMENT,CONTACT,SWITCH SWITCH CONTACT ARRANGEMENT A DESIGNATION THAT DESCRIBES THE BASIC ELECTRICAL CONFIGURATION OF A SWITCH. SELECT REPLY CODE 10AD85 AEGKD /D/ 18TYPE,LOAD,SWITCH SWITCH LOAD TYPE INDICATES THE TYPE OF LOAD CURRENT FOR WHICH THE ITEM IS DESIGNED FOR OPERATION. SELECT REPLY CODE 10AA60 AEGLJ /D/A12QUANTITY,TERMINAL,RESISTOR/SWITCH RESISTOR/SWITCH TERMINAL QUANTITY THE NUMBER OF TERMINALS PROVIDED FOR EXTERNAL CONNECTIONS AND WHETHER THEY ARE FOR THE SWITCH OR FOR THE RESISTOR. 1D AND 1A MODE REPLY11AC99 AEGMB /D/ 10LOCATION IN OHMS,TAP TAP LOCATION IN OHMS THE RATED RESISTANCE VALUE BETWEEN THE COUNTERCLOCKWISE END TERMINAL OF A RESISTOR AND A TAP TERMINAL AT A POINT THAT PROVIDES CONNECTION TO AN INTERMEDIATE VALUE OF THE TOTAL RESISTANCE VALUE,EXPRESSED IN OHMS. 1B MODE REPLY 0 AEGNB /D/ 10LOCATION IN DEG OF EFFECTIVE ELECTRICAL ROTATION,TAP TAP LOCATION IN DEG OF EFFECTIVE ELECTRICAL ROTATION THE LOCATION BETWEEN THE COUNTERCLOCKWISE END TERMINAL OF A RESISTOR AND A TAP TERMINAL AT A POINT THAT PROVIDES CONNECTION TO AN INTERMEDIATE VALUE OF THE TOTAL RESISTANCE VALUE,EXPRESSED IN DEGREES OF EFFECTIVE ELECTRICAL ROTATION. 1B MODE REPLY 0 AEGPB /D/ 10LOCATION IN PERCENT OF TOTAL APPLIED VOLTAGE,TAP TAP LOCATION IN PERCENT OF TOTAL APPLIED VOLTAGE THE LOCATION BETWEEN THE END TERMINAL OF A RESISTOR AND A TAP TERMINAL AT A POINT THAT PROVIDES CONNECTION TO AN INTERMEDIATE VALUE OF THE TOTAL RESISTANCE VALUE,EXPRESSED IN PERCENT OF TOTAL APPLIED VOLTAGE. 1B MODE REPLY 0 AEGQJ /D/T10TOLERANCE,LOCATION,TAP TAP LOCATION TOLERANCE THE LIMITS OF PERMISSIBLE VARIATION FROM THE RATED VALUE OF THE LOCATION OF A TAP. 1D AND 1F MODE REPLY11AD00 AEGRB /D/ 10WIDTH IN DEG,TAP,EFFECTIVE EFFECTIVE TAP WIDTH IN DEG THE TRAVEL OF THE SHAFT DURING WHICH THE VOLTAGES AT THE WIPER TERMINAL AND AT THE TAP TERMINAL ARE ESSENTIALLY THE SAME AS THE WIPER IS MOVED PAST THE TAP IN ONE DIRECTION,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AEGSB /D/ 10RESOLUTION IN PERCENT RESOLUTION IN PERCENT THE RECIPROCAL OF THE NUMBER OF TURNS OF WIRE IN THE RESISTANCE WINDING IN THE ACTUAL ELECTRICAL TRAVEL. 1B MODE REPLY 0 AEGTB /D/ 10RESOLUTION IN PERCENT OF TOTAL TRAVEL,TRAVEL TRAVEL RESOLUTION IN PERCENT OF TOTAL TRAVEL THE MAXIMUM VALUE OF SHAFT TRAVEL IN ONE DIRECTION PER INCREMENTAL VOLTAGE STEP,IN ANY SPECIFIED PORTION OF THE RESISTIVE ELEMENT,EXPRESSED IN PERCENT OF TOTAL TRAVEL. 1B MODE REPLY 0 AEGUB /D/ 10RESOLUTION IN PERCENT OF TOTAL APPLIED VOLTAGE,VOLTAGE VOLTAGE RESOLUTION IN PERCENT OF TOTAL APPLIED VOLTAGE THE MAXIMUM INCREMENTAL CHANGE IN THE OUTPUT RATIO WITH SHAFT TRAVEL IN ONE DIRECTION,IN ANY SPECIFIED PORTION IN THE RESISTIVE ELEMENT,EXPRESSED IN PERCENT OF TOTAL APPLIED VOLTAGE. 1B MODE REPLY 0 AEGVB /D/ 10SMOOTHNESS IN PERCENT,OUTPUT OUTPUT SMOOTHNESS IN PERCENT A MEASUREMENT OF ANY SPURIOUS VARIATION IN THE ELECTRICAL OUTPUT NOT PRESENT IN THE INPUT,EXPRESSED AS A PRECENT OF THE TOTAL APPLIED VOLTAGE,AND MEASURED FOR SPECIFIED TRAVEL INCREMENTS OVER THE THEORETICAL ELECTRICAL TRAVEL,INCLUDES THE EFFECTS OF CONTACT RESISTANCE VARIATIONS,RESOLUTION,AND OTHER MICRO-NONLINEARITIES IN THE OUTPUT. 1B MODE REPLY 0 AEGWB /D/ 10VOLTAGE IN MILLIVOLTS PER VOLT QUADRATURE VOLTAGE IN MILLIVOLTS PER VOLT QUADRATURE THE MAXIMUM VALUE OF THAT PORTION OF THE OUTPUT VOLTAGE THAT IS PLUS OR MINUS 90 DEGREES OUT OF TIME PHASE WITH THE INPUT VOLTAGE,EXPRESSED IN MILLIVOLTS PER VOLT APPLIED,MEASURED AT A SPECIFIED INPUT VOLTAGE AND FREQUENCY. 1B MODE REPLY 0 AEGXJ /D/ 04DISTANCE BETWEEN OUTSIDE TERMINALS ON LENGTH SIDE DISTANCE BETWEEN OUTSIDE TERMINALS ON LENGTH SIDE NONE. 2D AND 1B MODE REPLY21AA051AC20 AEGYJ /D/ 04DISTANCE BETWEEN INSIDE TERMINALS ON LENGTH SIDE DISTANCE BETWEEN INSIDE TERMINALS ON LENGTH SIDE NONE. 2D AND 1B MODE REPLY21AA051AC20 AEGZJ /D/ 04DISTANCE BETWEEN TERMINALS ON WIDTH SIDE DISTANCE BETWEEN TERMINALS ON WIDTH SIDE NONE. 2D AND 1B MODE REPLY21AA051AC20 AEHAJ 04DISTANCE BETWEEN CENTERLINES OF MOUNTING FACILITIES PARALLEL TO BODY WIDTH DISTANCE BETWEEN CENTERLINES OF MOUNTING FACILITIES PARALLEL TO BODY WIDTH THE DISTANCE BETWEEN CENTERLINES OF MOUNTING FACILITIES PARALLEL TO THE WIDTH OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 AEHBJ /D/ 04DISTANCE BETWEEN LOWER MOUNTING FACILITIES PARALLEL TO BODY LENGTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN LOWER MOUNTING FACILITIES PARALLEL TO BODY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEHCD 19MODE OF OSCILLATION MODE OF OSCILLATION THE MODE OF FREQUENCY AT WHICH THE DEVICE IS DESIGNED TO OPERATE. SELECT REPLY CODE 10AD12 AEHDD 19RESONANCE,CIRCUIT CIRCUIT RESONANCE THE CONDITION EXISTING WHEN THE FREQUENCY OR VIBRATION EQUALS THE NATURAL FREQUENCY. SELECT REPLY CODE 10AD13 AEHEJ 10CAPACITANCE IN PICOFARADS,LOAD LOAD CAPACITANCE IN PICOFARADS THE AMOUNT OF ELECTRICAL CAPACITANCE UNDER A LOAD CONDITION,REQUIRED FOR NORMAL OPERATION IN A CIRCUIT,EXPRESSED IN PICOFARADS. 1D AND 1B MODE REPLY11AC20 AEHFJ 10CAPACITANCE IN PICOFARADS,SHUNT SHUNT CAPACITANCE IN PICOFARADS THE TOTAL STATIC CAPACITANCE OF THE ITEM WHEN MEASURED ACROSS THE TERMINALS,EXPRESSED IN PICOFARADS. 1D AND 1B MODE REPLY11AC20 AEHGJ 10FREQUENCY,SPECIFIED SPECIFIED FREQUENCY THE FREQUENCY AT WHICH THE ITEM IS DESIGNED TO OPERATE UNDER SPECIFIED CONDITIONS. 1D AND 1B MODE REPLY11AC32 AEHHF /D/T10TOLERANCE FOR OPERATING TEMP RANGE IN PERCENT,FREQUENCY FREQUENCY TOLERANCE FOR OPERATING TEMP RANGE IN PERCENT THE PERMISSIBLE DEVIATION FROM THE SPECIFIED FREQUENCY WITHIN THE OPERATING TEMPERATURE RANGE,EXPRESSED IN PERCENT. 1F MODE REPLY 0 AEHJD /D/ 07CONTROLLED,TEMPERATURE TEMPERATURE CONTROLLED INDICATES WHETHER OR NOT THE ITEM IS HEAT CONTROLLED. SELECT REPLY CODE 10AA89 AEHKF T10TOLERANCE AT REFERENCE TEMP IN PERCENT,FREQUENCY FREQUENCY TOLERANCE AT REFERENCE TEMP IN PERCENT THE PERMISSIBLE FREQUENCY DEVIATION WHEN OPERATING AT THE REFERENCE TEMPERATURE,EXPRESSED IN PERCENT. 1F MODE REPLY 0 AEHLF T10STABILITY IN PERCENT,FREQUENCY FREQUENCY STABILITY IN PERCENT THE ALLOWABLE FREQUENCY DEVIATION FROM THE FREQUENCY MEASURED AT THE REFERENCE TEMPERATURE,EXPRESSED IN PERCENT. 1F MODE REPLY 0 AEHMJ 10TEMP,REFERENCE,CONTROLLED CONTROLLED REFERENCE TEMP THE TEMPERATURE AT THE MIDPOINT OF THE CONTROLLED OPERATING TEMPERATURE RANGE. 1D AND 1B MODE REPLY11AB36 AEHNJ T10RANGE,TEMP,OPERABLE OPERABLE TEMP RANGE THE TEMPERATURE RANGE OVER WHICH UNITS,DESIGNED FOR CONTROLLED TEMPERATURE CONDITIONS,WILL OSCILLATE. 1D AND 1F MODE REPLY11AB36 AEHPB /D/ 10VALUE IN OHMS,RESISTANCE,EQUIVALENT EQUIVALENT RESISTANCE VALUE IN OHMS THE MAXIMUM EQUIVALENT (EFFECTIVE) RESISTANCE FOR WHICH THE ITEM IS RATED,EXPRESSED IN OHMS. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 1B MODE REPLY 0 AEHQJ /D/ 10POWER RATING IN MILLIWATTS,LEVEL,DRIVE DRIVE LEVEL POWER RATING IN MILLIWATTS THE POWER DISSIPATION LEVEL AT WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN MILLIWATTS. 1D AND 1B MODE REPLY11AC20 AEHRJ /D/ 10CURRENT RATING IN MICROAMPS,LEVEL,DRIVE DRIVE LEVEL CURRENT RATING IN MICROAMPS THE OPERATING CURRENT LEVEL AT WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN MICROAMPERES. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 1D AND 1B MODE REPLY11AC20 AEHSD /D/ 09MATERIAL,COVER,HOLDER HOLDER COVER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HOLDER COVER IS FABRICATED. SELECT REPLY CODE 10AD09 AEHTJ 04DISTANCE BETWEEN TERMINALS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN TERMINALS THE CENTER TO CENTER DISTANCE BETWEEN TERMINALS. 2D AND 1B MODE REPLY21AA051AC20 AEHUJ /D/ 04DISTANCE BETWEEN TERMINALS CENTER TO CENTER,SECOND SECOND DISTANCE BETWEEN TERMINALS CENTER TO CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AEHVJ 04DISTANCE BETWEEN CENTER TERMINAL AND OUTSIDE TERMINAL CENTERS DISTANCE BETWEEN CENTER TERMINAL AND OUTSIDE TERMINAL CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AEHWJ /D/ 04LENGTH SEAL-OFF TIP LENGTH SEAL-OFF TIP NONE. 2D AND 1B MODE REPLY21AA051AC20 AEHXJ 10DISSIPATION RATING,POWER,MAXIMUM MAXIMUM POWER DISSIPATION RATING THE MAXIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY AN ITEM. 1D AND 1B MODE REPLY11AC33 AEHYJ 10TEMP AT FULL RATED POWER,AMBIENT AMBIENT TEMP AT FULL RATED POWER THE TEMPERATURE OF THE MEDIUM SURROUNDING AN ITEM AT WHICH IT CAN BE OPERATED CONTINUOUSLY AT FULL RATED POWER. 1D AND 1B MODE REPLY11AB36 AEHZJ 10TEMP,OPERATING,MAXIMUM MAXIMUM OPERATING TEMP THE MAXIMUM TEMPERATURE AT WHICH THE ITEM IS RATED TO OPERATE FOR AN EXTENDED PERIOD OF TIME. 1D AND 1B MODE REPLY11AB36 AEJAB 10CONSTANT IN SECONDS,TIME,THERMAL THERMAL TIME CONSTANT IN SECONDS THE TIME REQUIRED FOR THE TEMPERATURE OF AN ITEM TO CHANGE 63.2 PERCENT OF THE DIFFERENCE BETWEEN ITS INITIAL AND FINAL BODY TEMPERATURE WHEN SUBJECTED TO A TEMPERATURE CHANGE UNDER ZERO POWER CONDITIONS,EXPRESSED IN SECONDS. 1B MODE REPLY 0 AEJBB 10CONSTANT IN MILLIWATTS PER DEG CELSIUS,DISSIPATION,POWER POWER DISSIPATION CONSTANT IN MILLIWATTS PER DEG CELSIUS THE RATIO,AT A SPECIFIED AMBIENT TEMPERATURE,OF A CHANGE IN POWER DISSIPATION IN AN ITEM TO THE RESULTANT BODY TEMPERATURE CHANGE,EXPRESSED IN MILLIWATTS PER DEGREE CELSIUS. 1B MODE REPLY 0 AEJCB 10COEFFICIENT OF RESISTANCE IN PERCENT PER DEG CELSIUS,TEMP,ZERO POWER ZERO POWER TEMP COEFFICIENT OF RESISTANCE IN PERCENT PER DEG CELSIUS THE RATIO OF THE RATE OF CHANGE OF RESISTANCE WITH TEMPERATURE TO THE RESISTANCE OF THE ITEM AT A SPECIFIED TEMPERATURE,EXPRESSED IN PERCENT PER DEGREE CELSIUS. 1B MODE REPLY 0 AEJDJ 10POINTS FOR RESISTANCE READINGS AT ZERO POWER,TEMP TEMP POINTS FOR RESISTANCE READINGS AT ZERO POWER THE TEMPERATURE LEVELS AT WHICH RESISTANCE RATINGS HAVE BEEN ESTABLISHED,UNDER ZERO POWER CONDITION. 1D AND 1B MODE REPLY11AB36 AEJEJ 10RESISTANCE AT SPECIFIED TEMP,ZERO POWER ZERO POWER RESISTANCE AT SPECIFIED TEMP THE RESISTANCE AT A SELECTED TEMPERATURE,UNDER ZERO POWER CONDITION. 1D AND 1B MODE REPLY11AA57 AEJFF T10TOLERANCE AT A SPECIFIED TEMP IN PERCENT,RESISTANCE RESISTANCE TOLERANCE AT A SPECIFIED TEMP IN PERCENT THE LIMITS OF PERMISSIBLE VARIATION IN THE ELECTRICAL RESISTANCE VALUE OF AN ITEM AT A SELECTED TEMPERATURE IN PERCENT. 1F MODE REPLY 0 AEJGJ 04LENGTH,PROBE PROBE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE PROBE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AEJHJ 04DIAMETER,PROBE PROBE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AEJJJ 04RADIUS,INSIDE INSIDE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AEJKJ /D/ 04RADIUS AT SMALL END,HOLE HOLE RADIUS AT SMALL END NONE. 2D AND 1B MODE REPLY21AA051AC20 AEJLJ /D/ 04RADIUS AT LARGE END,HOLE HOLE RADIUS AT LARGE END NONE. 2D AND 1B MODE REPLY21AA051AC20 AEJMJ 04LENGTH,THRU-HOLE THRU-HOLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE THRU-HOLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AEJNJ 04DISTANCE BETWEEN MOUNTING FACILITY CENTERS DISTANCE BETWEEN MOUNTING FACILITY CENTERS THE DISTANCE BETWEEN MOUNTING FACILITY CENTERS. 2D AND 1B MODE REPLY21AA051AC20 AEJPD /D/ 02DESIGN,INSTALLATION INSTALLATION DESIGN THE TYPE OF INSTALLATION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AD18 AEJQD /D/ 09MATERIAL,EXTERIOR EXTERIOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE EXTERIOR SURFACES ARE FABRICATED. SELECT REPLY CODE 10AD09 AEJRD /D/ 07MATERIAL,CONSTRUCTION,NONMAGNETIC NONMAGNETIC CONSTRUCTION MATERIAL AN INDICATION OF WHETHER OR NOT THE ITEM IS CONSTRUCTED OF NONMAGNETIC MATERIAL. SELECT REPLY CODE 10AA89 AEJSD /D/ 07CANOPY CANOPY AN INDICATION OF WHETHER OR NOT A ROOFLIKE COVERING OR OVERHANG IS INCLUDED. SELECT REPLY CODE 10AA49 AEJTD /D/ 07SHELF,BACK BACK SHELF AN INDICATION OF WHETHER OR NOT A HORIZONTAL SURFACE ATTACHED TO THE BACK OF AN ITEM TO PROVIDE SUPPORT AND/OR STORAGE IS INCLUDED. SELECT REPLY CODE 10AA49 AEJUD /D/ 07TIMER,INTERVAL INTERVAL TIMER AN INDICATION OF WHETHER OR NOT A DEVICE DESIGNED TO MEASURE AND SIGNAL THE END OF A PREDETERMINED PERIOD OF TIME IS INCLUDED. SELECT REPLY CODE 10AA49 AEJVD /D/ 07OUTLET,APPLIANCE APPLIANCE OUTLET AN INDICATION OF WHETHER OR NOT A RECEPTACLE/S/ TO ACCOMMODATE PLUGS FOR STANDARD ELECTRICAL APPLIANCES IS INCLUDED. SELECT REPLY CODE 10AA49 AEJWD /D/ 07OUTLET,APPLIANCE,TIME CONTROLLED TIME CONTROLLED APPLIANCE OUTLET AN INDICATION OF WHETHER OR NOT A RECEPTACLE(S) WHICH IS CONTROLLED BY A DEVICE THAT ACTUATES AND DEACTUATES THE ELECTRICAL CIRCUIT TO WHICH THE OUTLET(S) IS CONNECTED IN ACCORDANCE WITH A PREDETERMINED PERIOD OF TIME IS INCLUDED. SELECT REPLY CODE 10AA49 AEJXD /D/ 07RAIL,GUARD GUARD RAIL AN INDICATION OF WHETHER OR NOT A BAR PLACED HORIZONTALLY ACROSS THE FRONT TO SERVE AS A GUARD OR SUPPORT IS INCLUDED. SELECT REPLY CODE 10AA49 AEJYD /D/ 07RACKS,SEA SEA RACKS AN INDICATION OF WHETHER OR NOT BARS OR RAILS DESIGNED TO HOLD UTENSILS ON THE COOKING SURFACE ARE INCLUDED. SELECT REPLY CODE 10AA49 AEJZJ 04DEPTH DEPTH A LINEAR MEASUREMENT FROM THE SURFACE TO A SPECIFIED INNER POINT ON AN ITEM,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AEKAJ 04HEIGHT,TOP,COOKING COOKING TOP HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE COOKING TOP, IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AEKBJ 04HEIGHT,OVEN OVEN HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE OVEN, IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AEKCJ 04WIDTH,OVEN OVEN WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE OVEN, IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AEKDJ 04DEPTH,OVEN OVEN DEPTH A LINEAR MEASUREMENT FROM THE SURFACE TO A SPECIFIED INNER POINT OF THE OVEN, IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AEKED /D/ 07OPERATION,AC AND DC,SIMULTANEOUS SIMULTANEOUS AC AND DC OPERATION AN INDICATION OF WHETHER OR NOT THE ITEM IS DESIGNED FOR SIMULTANEOUS AC AND DC OPERATION FROM SEPARATE ALTERNATING AND DIRECT CURRENT PRIMARY SOURCES. SELECT REPLY CODE 10AA89 AEKFA 12QUANTITY,OVEN OVEN QUANTITY THE NUMBER OF OVENS PROVIDED. 1A MODE REPLY 0 AEKGB /D/ 10DISSIPATION RATING IN WATTS,POWER,OVEN HEATING ELEMENT OVEN HEATING ELEMENT POWER DISSIPATION RATING IN WATTS THE MAXIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY AN OVEN HEATING ELEMENT,EXPRESSED IN WATTS. 1B MODE REPLY 0 AEKHD /D/ 07CONTROL,TEMP,OVEN OVEN TEMP CONTROL AN INDICATION OF WHETHER OR NOT A DEVICE DESIGNED TO AUTOMATICALLY CONTROL THE OVEN HEAT IS INCLUDED. SELECT REPLY CODE 10AA49 AEKJD /D/ 07CONTROL,TEMP,KEEP WARM OVEN KEEP WARM OVEN TEMP CONTROL AN INDICATION OF WHETHER OR NOT A DEVICE WITH A LOW HEAT SETTING BELOW THE COOKING TEMPERATURE RANGE OF THE OVEN IS INCLUDED. SELECT REPLY CODE 10AA49 AEKKD /D/ 07OVEN,CONTROLLED,TIME TIME CONTROLLED OVEN AN INDICATION OF WHETHER OR NOT AN OVEN/S/ CONTROLLED BY A DEVICE DESIGNED TO AUTOMATICALLY ACTUATE AND DEACTUATE THE HEATING ELEMENTS/S/ IN ACCORDANCE WITH A PREDETERMINED PERIOD OF TIME IS INCLUDED. SELECT REPLY CODE 10AA49 AEKLD 18TYPE,UNIT,HEATING,SURFACE SURFACE HEATING UNIT TYPE INDICATES THE TYPE OF HEATING UNIT(S) PROVIDED ON THE SURFACE. SELECT REPLY CODE 10AB04 AEKMA 12QUANTITY,UNIT,HEATING,SURFACE SURFACE HEATING UNIT QUANTITY THE NUMBER OF SURFACE HEATING UNITS PROVIDED. 1A MODE REPLY 0 AEKNB /D/ 10DISSIPATION RATING IN WATTS,POWER,SURFACE HEATING UNIT SURFACE HEATING UNIT POWER DISSIPATION RATING IN WATTS THE MAXIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY THE SURFACE HEATING ELEMENT/S/,EXPRESSED IN WATTS. 1B MODE REPLY 0 AEKPD /D/ 07CONTROL,TEMP,THERMOSTATIC,SURFACE HEATING UNIT SURFACE HEATING UNIT THERMOSTATIC TEMP CONTROL AN INDICATION OF WHETHER OR NOT A THERMOSTATIC DEVICE DESIGNED TO AUTOMATICALLY CONTROL THE SURFACE UNIT HEAT IS INCLUDED. SELECT REPLY CODE 10AA49 AEKQD /D/ 07SPACE,STORAGE STORAGE SPACE AN INDICATION OF WHETHER OR NOT COMPARTMENT/S/,SLIDING DRAWER/S/,AND THE LIKE,FOR STORING ARE INCLUDED. SELECT REPLY CODE 10AA49 AEKRD /D/ 07OVEN,WARMING WARMING OVEN AN INDICATION OF WHETHER OR NOT A COMPARTMENT FOR MAINTAINING FOOD AT A TEMPERATURE SUITABLE FOR SERVING IS INCLUDED. SELECT REPLY CODE 10AA49 AEKSB /D/ 10DISSIPATION RATING IN WATTS,POWER,HEATING ELEMENT,WARMING OVEN WARMING OVEN HEATING ELEMENT POWER DISSIPATION RATING IN WATTS THE MAXIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY THE WARMING OVEN HEATING ELEMENT,EXPRESSED IN WATTS. 1B MODE REPLY 0 AEKTD /D/ 07CONTROL,TEMP,WARMING OVEN WARMING OVEN TEMP CONTROL AN INDICATION OF WHETHER OR NOT A DEVICE DESIGNED TO AUTOMATICALLY CONTROL THE WARMING OVEN HEAT IS INCLUDED. SELECT REPLY CODE 10AA49 AEKUD 18TYPE,BROILER BROILER TYPE THE BASIC DESIGN OF THE BROILER/S/. SELECT REPLY CODE 10AD15 AEKVA 12QUANTITY,BROILER BROILER QUANTITY THE NUMBER OF BROILERS PROVIDED. 1A MODE REPLY 0 AEKWD 11METHOD,CONTROL,BROILER TEMP BROILER TEMP CONTROL METHOD THE MEANS EMPLOYED TO CONTROL THE TEMPERATURE OF THE BROILER HEATING ELEMENT. SELECT REPLY CODE 10AD16 AEKXB /D/ 10DISSIPATION RATING IN WATTS,POWER,HEATING ELEMENT,BROILER BROILER HEATING ELEMENT POWER DISSIPATION RATING IN WATTS THE MAXIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY THE BROILER HEATING ELEMENT,EXPRESSED IN WATTS. 1B MODE REPLY 0 AEKYD /D/ 08LOCATION,BOX,FIRE FIRE BOX LOCATION INDICATES THE LOCATION OF THE FIRE BOX. SELECT REPLY CODE 10AE46 AEKZD /D/ 07UNIT,BLOWER,MOTOR DRIVEN MOTOR DRIVEN BLOWER UNIT AN INDICATION OF WHETHER OR NOT A MOTOR DRIVEN BLOWER UNIT IS INCLUDED. SELECT REPLY CODE 10AA49 AELAD 18TYPE,CURRENT,BLOWER UNIT MOTOR BLOWER UNIT MOTOR CURRENT TYPE INDICATES THE TYPE OF CURRENT FOR WHICH THE BLOWER UNIT MOTOR IS DESIGNED. SELECT REPLY CODE 10AB62 AELBB 10VOLTAGE RATING IN VOLTS,MOTOR,BLOWER UNIT BLOWER UNIT MOTOR VOLTAGE RATING IN VOLTS THE ELECTRICAL VOLTAGE VALUE FOR WHICH THE BLOWER UNIT MOTOR IS RATED,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AELCB 10FREQUENCY IN HERTZ,MOTOR,BLOWER UNIT BLOWER UNIT MOTOR FREQUENCY IN HERTZ THE CYCLES PER SECOND /HERTZ/ OF THE BLOWER UNIT MOTOR ALTERNATING CURRENT. 1B MODE REPLY 0 AELDD 19PHASE,INPUT,BLOWER UNIT MOTOR BLOWER UNIT MOTOR INPUT PHASE THE NUMBER OF ALTERNATING CURRENT PHASES OF THE BLOWER UNIT MOTOR INPUT. SELECT REPLY CODE 10AD02 AELED /D/ 07REGULATOR,PRESSURE,GAS GAS PRESSURE REGULATOR AN INDICATION OF WHETHER OR NOT A DEVICE DESIGNED TO REGULATE PRESSURE ON THE GAS SUPPLY IS INCLUDED. SELECT REPLY CODE 10AA49 AELFJ 04DEPTH,OVERALL OVERALL DEPTH AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF AN ITEM,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 AELGJ 04LENGTH,OPENING,COVER COVER OPENING LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AELHJ 04WIDTH,OPENING,COVER COVER OPENING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AELJJ 04DIAMETER,OPENING,COVER COVER OPENING DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AELKJ /D/ 04DIAMETER,OPENING,RECEPTACLE RECEPTACLE OPENING DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AELLJ /D/ 04DEPTH,DOME DOME DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AELMJ /D/ 04DIAMETER,OUTLET,WIRE,FIRST COVER FIRST COVER WIRE OUTLET DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AELNJ /D/ 04DIAMETER,OUTLET,WIRE,SECOND COVER SECOND COVER WIRE OUTLET DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AELPJ /D/ 04DIAMETER,OUTLET,WIRE,THIRD COVER THIRD COVER WIRE OUTLET DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AELQJ /D/ 04DIAMETER,OUTLET,WIRE,FOURTH COVER FOURTH COVER WIRE OUTLET DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AELRD 18TYPE,ENTRANCE,CONDUIT CONDUIT ENTRANCE TYPE INDICATES THE TYPE OF ENTRANCE(S) PROVIDED TO ACCOMMODATE THE CONDUIT. SELECT REPLY CODE 10AD17 AELSD 18TYPE ACCOMMODATED,CONDUIT CONDUIT TYPE ACCOMMODATED INDICATES THE TYPE OF CONDUIT WHICH THE ITEM IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AC23 AELTD /D/ 14SHAPE,COVER COVER SHAPE THE PHYSICAL CONFIGURATION OF THE COVER ON A PLANE THAT IS PARALLEL TO THE MOUNTING SURFACE. SELECT REPLY CODE 10AD07 AELUA 03DESIGNATION,TRADE TRADE DESIGNATION THE DESIGNATION BY WHICH THE ITEM IS IDENTIFIED THROUGHOUT INDUSTRY. 1A MODE REPLY 0 AELVD /D/ 11METHOD,MOUNTING,COVER COVER MOUNTING METHOD THE MEANS BY WHICH THE COVER IS ATTACHED. SELECT REPLY CODE 10AB89 AELWA 12QUANTITY,HOLE,COVER MOUNTING COVER MOUNTING HOLE QUANTITY THE NUMBER OF HOLES PROVIDED TO ATTACH THE COVER. 1A MODE REPLY 0 AELXJ /D/ 04DIAMETER,HOLE,MOUNTING,COVER COVER MOUNTING HOLE DIAMETER THE DIAMETER OF A THREADLESS ROUND MOUNTING HOLE/S/ PROVIDED TO ATTACH THE COVER. 1D AND 1B MODE REPLY11AA05 AELYL 16STYLE,ARRANGEMENT,COVER MOUNTING HOLE COVER MOUNTING HOLE ARRANGEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE COVER MOUNTING HOLES. 1L MODE REPLY 0 AELZJ /D/ 04SPACING,HOLE,FIRST HORIZONTAL MOUNTING FIRST HORIZONTAL MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 AEMAJ /D/ 04SPACING,HOLE,SECOND HORIZONTAL MOUNTING SECOND HORIZONTAL MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 AEMBJ /D/ 04SPACING,HOLE,THIRD HORIZONTAL MOUNTING THIRD HORIZONTAL MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 AEMCJ /D/ 04SPACING,HOLE,FOURTH HORIZONTAL MOUNTING FOURTH HORIZONTAL MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 AEMDJ /D/ 04SPACING,HOLE,FIFTH HORIZONTAL MOUNTING FIFTH HORIZONTAL MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 AEMEJ /D/ 04SPACING,HOLE,SIXTH HORIZONTAL MOUNTING SIXTH HORIZONTAL MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 AEMFJ /D/ 04SPACING,HOLE,SEVENTH HORIZONTAL MOUNTING SEVENTH HORIZONTAL MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 AEMGJ /D/ 04SPACING,HOLE,EIGHTH HORIZONTAL MOUNTING EIGHTH HORIZONTAL MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 AEMHJ /D/ 04SPACING,HOLE,NINTH HORIZONTAL MOUNTING NINTH HORIZONTAL MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 AEMJJ /D/ 04SPACING,HOLE,TENTH HORIZONTAL MOUNTING TENTH HORIZONTAL MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 AEMKJ /D/ 04SPACING,HOLE,ELEVENTH HORIZONTAL MOUNTING ELEVENTH HORIZONTAL MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 AEMLJ /D/ 04SPACING,HOLE,FIRST VERTICAL MOUNTING FIRST VERTICAL MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 AEMMJ /D/ 04SPACING,HOLE,SECOND VERTICAL MOUNTING SECOND VERTICAL MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 AEMNJ /D/ 04SPACING,HOLE,THIRD VERTICAL MOUNTING THIRD VERTICAL MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 AEMPJ /D/ 04SPACING,HOLE,FOURTH VERTICAL MOUNTING FOURTH VERTICAL MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 AEMQJ /D/ 04SPACING,HOLE,FIFTH VERTICAL MOUNTING FIFTH VERTICAL MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 AEMRA 12QUANTITY,GANG,WIRING DEVICE WIRING DEVICE GANG QUANTITY THE NUMBER OF STANDARD SIZED WIRING DEVICES ACCOMMODATED. 1A MODE REPLY 0 AEMSD 11METHOD,PARTITIONING,MULTIGANG OUTLET MULTIGANG OUTLET PARTITIONING METHOD THE MEANS BY WHICH THE MULTIGANG OUTLETS ARE SEPARATED. SELECT REPLY CODE 10AD19 AEMTD 18TYPE,SURFACE,COVER MOUNTING COVER MOUNTING SURFACE TYPE INDICATES THE TYPE OF MOUNTING SURFACE ON THE COVER. SELECT REPLY CODE 10AD20 AEMUD 18TYPE,GASKET,MOUNTING,COVER COVER MOUNTING GASKET TYPE INDICATES THE TYPE OF MOUNTING GASKET PROVIDED FOR THE COVER. SELECT REPLY CODE 10AA83 AEMVD /D/ 09MATERIAL,GASKET,MOUNTING,COVER COVER MOUNTING GASKET MATERIAL THE COMPOSITION OF THE COVER MOUNTING GASKET. SELECT REPLY CODE 10AD09 AEMWA 12QUANTITY,COVER COVER QUANTITY THE NUMBER OF COVERS FURNISHED WITH THE ITEM. 1A MODE REPLY 0 AEMXL 16STYLE,COVER,FUNCTIONAL FUNCTIONAL COVER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FUNCTIONAL COVER. 1L MODE REPLY 0 AEMYD /D/ 01COLOR,LENS,INDICATOR LIGHT INDICATOR LIGHT LENS COLOR THE HUE OR TINT OF THE LENS IN THE COVER WHICH INDICATES A CONDITION OR FUNCTION. SELECT REPLY CODE 10AD06 AEMZD /D/ 07ACCOMMODATION,COVER,REMOVABLE SIDE PLATE REMOVABLE SIDE PLATE COVER ACCOMMODATION AN INDICATION OF WHETHER OR NOT A REMOVABLE SIDE PLATE COVER/S/ ACCOMMODATION IS INCLUDED. SELECT REPLY CODE 10AA49 AENAD /D/ 11METHOD,MOUNTING,CONDUIT OUTLET CONDUIT OUTLET MOUNTING METHOD THE MEANS PROVIDED TO FACILITATE MOUNTING THE CONDUIT OUTLET. SELECT REPLY CODE 10AB89 AENBD 19INSCRIPTION,LEGEND LEGEND INSCRIPTION THE INSCRIPTION AFFIXED TO OR STAMPED ON THE ITEM,EXCLUDING THE PART NUMBER. SELECT REPLY CODE 10AD21 AENCA 12QUANTITY,PUMP PUMP QUANTITY THE NUMBER OF PUMPS INCORPORATED IN THE ITEM. 1A MODE REPLY 0 AENDA 19ACTIVITY,CONTROL,DESIGN,NEXT HIGHER ASSEMBLY NEXT HIGHER ASSEMBLY DESIGN CONTROL ACTIVITY THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE GOVERNMENT AGENCY,INDUSTRIAL ORGANIZATION,OR OTHER ENTITY,WHICH CONTROLS THE DESIGN OF THE NEXT HIGHER ASSEMBLY. 1A MODE REPLY 0 AENED /D/ 09MATERIAL,BODY,PUMP PUMP BODY MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PUMP BODY IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AENFD /D/ 19GAS FOR WHICH DESIGNED,SPECIFIC SPECIFIC GAS FOR WHICH DESIGNED THE SPECIFIC GAS WITH WHICH THE ITEM IS DESIGNED TO BE USED. PLEASE USE MRC AAXK IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB75 AENGD 18TYPE,ELEMENT,PUMPING PUMPING ELEMENT TYPE INDICATES THE TYPE OF PUMPING ELEMENT INCLUDED ON THE ITEM. SELECT REPLY CODE 10AD04 AENHA 12QUANTITY,CYLINDER,PUMP PUMP CYLINDER QUANTITY THE NUMBER OF CYLINDERS INCLUDED IN THE PUMP. 1A MODE REPLY 0 AENJD 18TYPE,FLUID,PUMPING PUMPING FLUID TYPE INDICATES THE TYPE OF PUMPING FLUID USED IN THE ITEM. SELECT REPLY CODE 10AD22 AENKD /D/ 11METHOD,COOLING COOLING METHOD THE MEANS OF COOLING USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE ITEM. PLEASE USE MRC BFMF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AC16 AENLJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CONNECTION,INTAKE INTAKE CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE INTAKE CONNECTION THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AC21 AENMJ 04DIAMETER,OUTSIDE,INTAKE CONNECTION INTAKE CONNECTION OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INTAKE CONNECTION,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AENNJ 04DIAMETER,INSIDE,INTAKE CONNECTION INTAKE CONNECTION INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INTAKE CONNECTION,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AENPA /D/ 16STYLE,FACE,FLANGE,INTAKE CONNECTION INTAKE CONNECTION FLANGE FACE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE INTAKE CONNECTION FLANGE FACE. 1A MODE REPLY 0 AENQL 16STYLE,SHAPE,INTAKE CONNECTION FLANGE INTAKE CONNECTION FLANGE SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE INTAKE CONNECTION FLANGE. 1L MODE REPLY 0 AENRJ /D/ 04HEIGHT,FACE,RAISED,INTAKE CONNECTION INTAKE CONNECTION RAISED FACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AENSJ /D/ 04DIAMETER,FACE,RAISED,INTAKE CONNECTION INTAKE CONNECTION RAISED FACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AENTJ /D/ 04DIAMETER,RECESS,INTAKE CONNECTION INTAKE CONNECTION RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AENUJ /D/ 04DEPTH,RECESS,INTAKE CONNECTION INTAKE CONNECTION RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AENVJ 04DIAMETER,OUTSIDE,INTAKE CONNECTION FLANGE INTAKE CONNECTION FLANGE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INTAKE CONNECTION FLANGE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AENWJ 04THICKNESS,FLANGE,INTAKE CONNECTION INTAKE CONNECTION FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AENXJ /D/ 04LENGTH,FLANGE,INTAKE CONNECTION INTAKE CONNECTION FLANGE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AENYJ /D/ 04WIDTH,FLANGE,INTAKE CONNECTION INTAKE CONNECTION FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AENZJ /D/ 04RADIUS,END,INTAKE CONNECTION FLANGE INTAKE CONNECTION FLANGE END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AEPAJ /D/ 04WIDTH ACROSS FLATS,CONNECTION,INTAKE INTAKE CONNECTION WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 AEPBA 12QUANTITY,HOLE,BOLT,INTAKE CONNECTION INTAKE CONNECTION BOLT HOLE QUANTITY NONE. 1A MODE REPLY 0 AEPCJ 04DIAMETER,HOLE,BOLT,INTAKE CONNECTION INTAKE CONNECTION BOLT HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AEPDJ 04DIAMETER,CIRCLE,BOLT,INTAKE CONNECTION INTAKE CONNECTION BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AEPEJ /D/ 04DISTANCE BETWEEN BOLT HOLE CENTERS ALONG LENGTH,CONNECTION,INTAKE INTAKE CONNECTION DISTANCE BETWEEN BOLT HOLE CENTERS ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEPFJ /D/ 04DISTANCE BETWEEN BOLT HOLE CENTERS ALONG WIDTH,CONNECTION,INTAKE INTAKE CONNECTION DISTANCE BETWEEN BOLT HOLE CENTERS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEPGJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CONNECTION,DISCHARGE DISCHARGE CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE DISCHARGE CONNECTION THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AC21 AEPHJ 04DIAMETER,OUTSIDE,DISCHARGE CONNECTION DISCHARGE CONNECTION OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DISCHARGE CONNECTION,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AEPJJ 04DIAMETER,INSIDE,DISCHARGE CONNECTION DISCHARGE CONNECTION INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE PASSING THROUGH THE CENTER OF THE DISCHARGE CONNECTION,WITH TERMINATED POINTS ON THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AEPKA /D/ 16STYLE,FACE,DISCHARGE CONNECTION FLANGE DISCHARGE CONNECTION FLANGE FACE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE DISCHARGE CONNECTION FLANGE FACE. 1A MODE REPLY 0 AEPLJ /D/ 04HEIGHT,FACE,RAISED,DISCHARGE CONNECTION DISCHARGE CONNECTION RAISED FACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AEPMJ /D/ 04DIAMETER,FACE,RAISED,DISCHARGE CONNECTION DISCHARGE CONNECTION RAISED FACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AEPNJ /D/ 04DIAMETER,RECESS,DISCHARGE CONNECTION DISCHARGE CONNECTION RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AEPPJ /D/ 04DEPTH,RECESS,DISCHARGE CONNECTION DISCHARGE CONNECTION RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEPQL 16STYLE,SHAPE,DISCHARGE CONNECTION FLANGE DISCHARGE CONNECTION FLANGE SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE DISCHARGE CONNECTION FLANGE. 1L MODE REPLY 0 AEPRJ 04DIAMETER,OUTSIDE,FLANGE FLANGE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FLANGE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AEPSJ 04THICKNESS,FLANGE,DISCHARGE CONNECTION DISCHARGE CONNECTION FLANGE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE DISCHARGE CONNECTION FLANGE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AEPTJ /D/ 04LENGTH,FLANGE,DISCHARGE CONNECTION DISCHARGE CONNECTION FLANGE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEPUJ /D/ 04WIDTH,FLANGE,DISCHARGE CONNECTION DISCHARGE CONNECTION FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEPVJ /D/ 04RADIUS,END,DISCHARGE CONNECTION FLANGE DISCHARGE CONNECTION FLANGE END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AEPWJ /D/ 04WIDTH ACROSS FLATS,CONNECTION,DISCHARGE DISCHARGE CONNECTION WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 AEPXA 12QUANTITY,HOLE,BOLT,DISCHARGE CONNECTION DISCHARGE CONNECTION BOLT HOLE QUANTITY NONE. 1A MODE REPLY 0 AEPYJ 04DIAMETER,HOLE,BOLT,DISCHARGE CONNECTION DISCHARGE CONNECTION BOLT HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AEPZJ 04DIAMETER,CIRCLE,BOLT,DISCHARGE CONNECTION DISCHARGE CONNECTION BOLT CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DISCHARGE CONNECTION BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AEQAJ /D/ 04DISTANCE BETWEEN BOLT HOLE CENTERS ALONG LENGTH,CONNECTION,DISCHARGE DISCHARGE CONNECTION DISTANCE BETWEEN BOLT HOLE CENTERS ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEQBJ /D/ 04DISTANCE BETWEEN BOLT HOLE CENTERS ALONG WIDTH,CONNECTION,DISCHARGE DISCHARGE CONNECTION DISTANCE BETWEEN BOLT HOLE CENTERS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEQCB 10SPEED AT RATED CAPACITY IN RPM,OPERATING OPERATING SPEED AT RATED CAPACITY IN RPM THE SPEED OF THE DRIVE SHAFT REQUIRED TO PRODUCE THE RATED CAPACITY OF AN ITEM,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 AEQDD /D/ 07TANK,SEPARATOR SEPARATOR TANK AN INDICATION OF WHETHER OR NOT A SEPARATOR TANK IS INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA49 AEQEJ /D/ 10CAPACITY,TANK,STORAGE,VACUUM VACUUM STORAGE TANK CAPACITY THE VOLUME OF THE VACUUM STORAGE CONTAINER/S/. 1D AND 1B MODE REPLY11AB10 AEQFJ /D/ 10FOREPRESSURE,OPERATING OPERATING FOREPRESSURE THE REDUCED PRESSURE REQUIRED FOR OPERATING THE ITEM. 1D AND 1B MODE REPLY11AC43 AEQGD 19DEVICE,PREVENTATIVE,VAPOR CONDENSATION VAPOR CONDENSATION PREVENTATIVE DEVICE THE DEVICE WHICH PREVENTS OR REDUCES THE AMOUNT OF CONDENSABLE VAPORS FROM ENTERING AND CONTAMINATING THE ITEM. SELECT REPLY CODE 10AD24 AEQHJ 10DISPLACEMENT RATE,AIR AIR DISPLACEMENT RATE THE VOLUME OF AIR PASSED PER UNIT OF TIME THROUGH AN ITEM. 2D AND 1B MODE REPLY21AC641AD25 AEQJJ 10TEMP,OPERATING,MINIMUM MINIMUM OPERATING TEMP THE MINIMUM TEMPERATURE AT WHICH THE ITEM IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY11AB36 AEQKJ 04HEIGHT,SPACE,PANEL PANEL SPACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AEQLB 04ANGLE IN DEG,SLOPE,PANEL PANEL SLOPE ANGLE IN DEG NONE. 1B MODE REPLY 0 AEQMJ 04WIDTH,INSIDE,DRAWER DRAWER INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEQNJ 04DEPTH,INSIDE,DRAWER DRAWER INSIDE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEQPJ 10SPACING,CROSS-MEMBER CROSS-MEMBER SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 AEQQJ 04THICKNESS,STRINGER STRINGER THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AEQRJ 04WIDTH,STRINGER STRINGER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE STRINGER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AEQSJ 04WIDTH,CLEARANCE CLEARANCE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEQTJ 04THICKNESS,RAIL,PANEL PANEL RAIL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AEQUJ /D/ 04HEIGHT,SPACE,UPPER PANEL UPPER PANEL SPACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AEQVJ /D/ 04HEIGHT,SPACE,LOWER PANEL LOWER PANEL SPACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AEQWJ /D/ 04HEIGHT,SPACE,LEFT PANEL LEFT PANEL SPACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AEQXJ /D/ 04HEIGHT,SPACE,RIGHT PANEL RIGHT PANEL SPACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AEQYJ 04WIDTH,SHELF SHELF WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A SHELF,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AEQZJ 04DEPTH,SHELF SHELF DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AERAD /D/ 07PREWIRING PREWIRING AN INDICATION OF WHETHER OR NOT WIRING TO ACCOMMODATE THE ELECTRICAL AND/OR ELECTRONIC EQUIPMENT,FOR WHICH THE ITEM IS DESIGNED,IS INCLUDED. SELECT REPLY CODE 10AA49 AERBD /D/ 07ADJUSTABILITY,FEET,MOUNTING MOUNTING FEET ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE MOUNTING FEET PROVIDED ARE ADJUSTABLE. SELECT REPLY CODE 10AC06 AERCL 16STYLE,DESIGN,PANEL MOUNTING RAIL PANEL MOUNTING RAIL DESIGN STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE DESIGN OF THE PANEL MOUNTING RAIL. 1L MODE REPLY 0 AERDL 16STYLE,ARRANGEMENT,HOLE,PANEL MOUNTING RAIL PANEL MOUNTING RAIL HOLE ARRANGEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE HOLE ARRANGEMENT OF THE PANEL MOUNTING RAIL. 1L MODE REPLY 0 AERED /D/ 07CAPABILITY,DISASSEMBLY DISASSEMBLY CAPABILITY AN INDICATION OF WHETHER OR NOT THE ITEM IS CAPABLE OF BEING DISASSEMBLED. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. SELECT REPLY CODE 10AA89 AERFD 18TYPE,MECHANISM,SLIDE SLIDE MECHANISM TYPE INDICATES THE TYPE OF MECHANISM PROVIDED FOR MOVING THE ITEM. SELECT REPLY CODE 10AD23 AERGD /D/ 05DIRECTION,ACTION,TILT MECHANISM TILT MECHANISM ACTION DIRECTION THE DIRECTION OF MOVEMENT PERMITTED BY THE TILT MECHANISM. SELECT REPLY CODE 10AC65 AERHJ /D/T10RANGE,ADJUSTABILITY,BRACKET BRACKET ADJUSTABILITY RANGE THE LIMITS OF THE ADJUSTABLE BRACKET WHICH SUPPORTS THE SLIDE ASSEMBLY OF THE DRAWER OR SHELF,IN ORDER TO ACCOMMODATE RACKS OF VARYING DEPTHS. 1D AND 1F MODE REPLY11AA05 AERJJ /D/ 04DISTANCE,TRAVEL TRAVEL DISTANCE THE DISTANCE THE ITEM IS DESIGNED TO TRAVEL FROM ITS FULLY CLOSED TO ITS FULLY OPEN POSITION. 1D AND 1B MODE REPLY11AA05 AERKD /D/ 07PROVISION,GROUNDING GROUNDING PROVISION AN INDICATION OF WHETHER OR NOT A METAL STRAP,CABLE,WIRE,OR THE LIKE,IS INCLUDED TO PROVIDE A CURRENT PATH TO GROUND TO ASSURE THAT THE ITEM WILL NOT BE ELECTRICALLY CHARGED. SELECT REPLY CODE 10AA49 AERLJ /D/ 10CAPACITY,WEIGHT,MAXIMUM MAXIMUM WEIGHT CAPACITY THE MAXIMUM WEIGHT THAT THE ITEM IS DESIGNED TO SUPPORT. REPLACED BY MRC CSMX. PLEASE USE MRC CSMX IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1B MODE REPLY11AB10 AERMD /D/ 07MECHANISM,EJECTION,EQUIPMENT EQUIPMENT EJECTION MECHANISM AN INDICATION OF WHETHER OR NOT A MECHANICAL DEVICE TO ASSIST IN REMOVAL OF ENCASED EQUIPMENT FROM A MOUNTING BASE IN INCLUDED. SELECT REPLY CODE 10AA49 AERNJ /D/T10RANGE,RATING,LOAD,VIBRATION MOUNT VIBRATION MOUNT LOAD RATING RANGE THE RATED LOAD RANGE THE ITEM IS DESIGNED TO SUPPORT WHILE RETAINING ITS RATED VIRBRATION AND SHOCK ISOLATION CHARACTERISTICS. 1D AND 1F MODE REPLY11AB10 AERPD 02DESIGN,SYSTEM SYSTEM DESIGN AN INDICATION OF THE SYSTEM FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AD26 AERQD 18TYPE,DOOR DOOR TYPE INDICATES THE TYPE OF DOOR FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AD27 AERRD /D/ 09MATERIAL,TOP,SHELF SHELF TOP MATERIAL THE MATERIAL OF WHICH THE TOP OR WORK PORTION OF THE SHELF IS FABRICATED. SELECT REPLY CODE 10AD09 AERSD /D/ 19PROVISIONS,MOUNTING,OPERATING COMPONENT OPERATING COMPONENT MOUNTING PROVISIONS THE PROVISIONS FURNISHED FOR MOUNTING OPERATING COMPONENTS IN OR ON THE ITEM. SELECT REPLY CODE 10AB21 AERTA /D/ 12QUANTITY,FACILITIES,MOUNTING,OPERATING COMPONENT OPERATING COMPONENT MOUNTING FACILITIES QUANTITY THE NUMBER OF FACILITIES PROVIDED FOR MOUNTING THE OPERATING COMPONENTS. 1A MODE REPLY 0 AERUD 18TYPE,FACILITY,HANDLING HANDLING FACILITY TYPE INDICATES THE TYPE OF PROVISIONS FURNISHED WHICH AID IN PUSHING,PULLING,OR TRANSPORTING THE ITEM. SELECT REPLY CODE 10AD28 AERVD 07FEATURE,ADD-ON ADD-ON FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM IS DESIGNED TO BE COMBINED WITH A LIKE ITEM,OR ITEMS THROUGH SHARED OR JOINED STRUCTURE,OR SPECIAL TRIM. SELECT REPLY CODE 10AA89 AERWJ 04THICKNESS,OVERALL OVERALL THICKNESS A MEASUREMENT OF THE SMALLEST OVERALL DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 AERXJ /D/ 04WIDTH,SLOT,SECOND MOUNTING SECOND MOUNTING SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AERYJ /D/ 04DEPTH,SLOT,SECOND MOUNTING SECOND MOUNTING SLOT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AERZJ 04WIDTH,FLANGE FLANGE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A FLANGE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AESAJ 04LENGTH,EAR,MOUNTING MOUNTING EAR LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AESBJ 04WIDTH,EAR,MOUNTING MOUNTING EAR WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AESCJ 04DIAMETER,MAJOR,TAPER TAPER MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CIRCULAR CROSS SECTION OF THE TAPERED PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AESDJ 04DIAMETER,END,MOUNTING MOUNTING END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MOUNTING END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AESED /D/ 09MATERIAL,FILTER FILTER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FILTER IS FABRICATED. SELECT REPLY CODE 10AD09 AESFD /D/ 09MATERIAL,HOLDER HOLDER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HOLDER IS FABRICATED. SELECT REPLY CODE 10AD09 AESGD /D/ 09MATERIAL,LENS LENS MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LENS IS FABRICATED. SELECT REPLY CODE 10AD09 AESHD /D/ 09MATERIAL,BASE BASE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BASE IS FABRICATED. PLEASE USE MRC MATT WITH ISAC OF BASE IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AESJJ 10PRESSURE DROP,MAXIMUM MAXIMUM PRESSURE DROP THE MAXIMUM PRESSURE LOSS BETWEEN THE INLET SIDE AND THE OUTLET SIDE OF AN ITEM. 1D AND 1B MODE REPLY11AB18 AESKD /D/ 18TYPE,DEVICE,LOCKING LOCKING DEVICE TYPE INDICATES THE TYPE OF DEVICE USED TO LOCK THE ITEM. SELECT REPLY CODE 10AD29 AESLL 03DESIGNATOR,PATTERN,STANDARD MOUNTING STANDARD MOUNTING PATTERN DESIGNATOR A DESIGNATION OF THE STANDARD MOUNTING FACILITY ARRANGEMENT PROVIDED. 1L MODE REPLY 0 AESMD /D/ 07ADJUSTABILITY,RAILS,MOUNTING,FRONT PANEL FRONT PANEL MOUNTING RAILS ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE FRONT PANEL MOUNTING RAILS ARE ADJUSTABLE. SELECT REPLY CODE 10AC06 AESND /D/ 07ADJUSTABILITY,RAILS,MOUNTING,BACK PANEL BACK PANEL MOUNTING RAILS ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE BACK PANEL MOUNTING RAILS ARE ADJUSTABLE. SELECT REPLY CODE 10AC06 AESPJ 04WIDTH ACCOMMODATED,PANEL PANEL WIDTH ACCOMMODATED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PANEL THAT THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AESQD /D/ 18TYPE,HOLE,FRONT PANEL MOUNTING RAIL FRONT PANEL MOUNTING RAIL HOLE TYPE INDICATES THE TYPE OF HOLES PROVIDED FOR MOUNTING FRONT PANELS TO THE MOUNTING RAILS. SELECT REPLY CODE 10AB68 AESRD /D/ 18TYPE,HOLE,BACK PANEL MOUNTING RAIL BACK PANEL MOUNTING RAIL HOLE TYPE INDICATES THE TYPE OF HOLES PROVIDED FOR MOUNTING BACK PANELS TO THE MOUNTING RAILS. SELECT REPLY CODE 10AB68 AESSJ /D/A13THREAD SIZE,HOLE,FRONT PANEL MOUNTING RAIL FRONT PANEL MOUNTING RAIL HOLE THREAD SIZE THE FRONT PANEL MOUNTING RAIL HOLE THREAD SERIES,THREAD MAJOR/MAXIMUM DIAMETER,AND NUMBER OF THREADS PER MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AC21 AESTJ /D/A13THREAD SIZE,HOLE,BACK PANEL MOUNTING RAIL BACK PANEL MOUNTING RAIL HOLE THREAD SIZE THE THREAD SERIES,THREAD MAJOR/MAXIMUM DIAMETER,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE BACK PANEL MOUNTING RAIL HOLE. 1D AND 1A MODE REPLY12AC21 AESUJ /D/ 04DIAMETER,HOLE,MOUNTING,FRONT PANEL MOUNTING RAIL FRONT PANEL MOUNTING RAIL MOUNTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FRONT PANEL MOUNTING RAIL,AND TERMINATES AT THE THREADLESS MOUNTING HOLE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AESVJ /D/ 04DIAMETER,HOLE,MOUNTING,BACK PANEL MOUNTING RAIL BACK PANEL MOUNTING RAIL MOUNTING HOLE DIAMETER THE DIAMETER OF A THREADLESS,ROUND MOUNTING HOLE. 2D AND 1B MODE REPLY21AA051AC20 AESWD 18TYPE,MOUNT,VIBRATION VIBRATION MOUNT TYPE INDICATES THE TYPE OF MOUNT PROVIDED TO ISOLATE THE ITEM FROM SHOCK AND VIBRATION. SELECT REPLY CODE 10AD31 AESXD /D/ 02DESIGN,FILTER,LIGHT TRANSMISSION LIGHT TRANSMISSION FILTER DESIGN THE FILTER DESIGN CHARACTERISTIC WHICH CONTROLS THE EMERGENCE OF LIGHT QUANTITY TRANSMITTED THROUGH A GIVEN FILTER. SELECT REPLY CODE 10AD56 AESYD /D/ 02DESIGN,LENS,LIGHT TRANSMISSION LIGHT TRANSMISSION LENS DESIGN THE LENS DESIGN CHARACTERISTIC WHICH CONTROLS THE EMERGENCE OF LIGHT QUANTITY TRANSMITTED THROUGH A GIVEN LENS. SELECT REPLY CODE 10AD56 AESZD /D/ 02DESIGN,BASE,LIGHT TRANSMISSION LIGHT TRANSMISSION BASE DESIGN THE BASE DESIGN CHARACTERISTIC WHICH CONTROLS THE EMERGENCE OF LIGHT QUANTITY TRANSMITTED THROUGH A GIVEN BASE. SELECT REPLY CODE 10AD56 AETAD /D/ 07HOLDER HOLDER AN INDICATION OF WHETHER OR NOT A HOLDER IS INCLUDED. SELECT REPLY CODE 10AA49 AETBD /D/ 09MATERIAL,EXPANDER EXPANDER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE EXPANDER IS FABRICATED, EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AETCJ 10HARDNESS RATING,METALLIC METALLIC HARDNESS RATING A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF A METALLIC ITEM WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE. 2D AND 1B MODE REPLY21AC202AC26 AETDA 12QUANTITY,ACCOMMODATION,PISTON PISTON ACCOMMODATION QUANTITY THE NUMBER OF PISTONS THAT CAN BE ACCOMMODATED BY THE ITEM. 1A MODE REPLY 0 AETEG /D/ 19PARTS,COMPONENT,RING SET RING SET COMPONENT PARTS A LISTING OF THE INDIVIDUAL COMPONENTS THAT ARE INCLUDED IN A RING SET. FULL TEXT WRITE-IN 0 AETFD 01COLOR,BASE BASE COLOR THE HUE OR TINT OF THE BASE. SELECT REPLY CODE 10AD06 AETGD 01COLOR,HOLDER HOLDER COLOR THE HUE OR TINT OF THE HOLDER. SELECT REPLY CODE 10AD06 AETHD /D/ 17SURFACE TREATMENT,HOLDER HOLDER SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A HOLDER SURFACE. SELECT REPLY CODE 10AD09 AETJD /D/ 07FEATURE,PRESS TO TEST PRESS TO TEST FEATURE AN INDICATION OF WHETHER OR NOT A PRESS TO TEST FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AETKD 18TYPE,DEVICE,DIMMING DIMMING DEVICE TYPE INDICATES THE TYPE OF DEVICE WHICH PERMITS MANUAL CONTROL OF THE AMOUNT OF LIGHT TRANSMITTED THROUGH THE LENS. SELECT REPLY CODE 10AD32 AETLD /D/ 19DEGREE OF BLACKOUT DEGREE OF BLACKOUT AN INDICATION OF WHETHER THE DIMMING DEVICE IS FOR A COMPLETE OR PARTIAL BLACKOUT. SELECT REPLY CODE 10AD33 AETMD 01COLOR,FILTER FILTER COLOR THE HUE OR TINT OF THE FILTER. SELECT REPLY CODE 10AD06 AETNA 19INSCRIPTION,LENS LENS INSCRIPTION THE INSCRIPTION AFFIXED TO OR STAMPED ON THE LENS,EXCLUDING THE PART NUMBER. 1A MODE REPLY 0 AETPA /D/ 19INSCRIPTION,INSERT INSERT INSCRIPTION THE INSCRIPTION AFFIXED TO OR STAMPED ON THE INSERT,EXCLUDING THE PART NUMBER. 1A MODE REPLY 0 AETQA /D/ 19INSCRIPTION,HOLDER HOLDER INSCRIPTION THE INSCRIPTION AFFIXED TO OR STAMPED ON THE HOLDER,EXCLUDING THE PART NUMBER. 1A MODE REPLY 0 AETRD /D/ 07FEATURE,INSCRIPTION,REVERSE REVERSE INSCRIPTION FEATURE AN INDICATION OF WHETHER OR NOT AN ITEM IS INSCRIBED IN THE REVERSE MANNER. SELECT REPLY CODE 10AA89 AETSD 01COLOR,INSCRIPTION INSCRIPTION COLOR THE HUE OR TINT OF THE INSCRIPTION ON THE ITEM. SELECT REPLY CODE 10AD06 AETTD 01COLOR,BACKGROUND,INSCRIPTION INSCRIPTION BACKGROUND COLOR THE HUE OR TINT OF THE LIGHT EMITTED FROM THAT PORTION OF THE ITEM WHICH SURROUNDS THE INSCRIPTION ON THE ITEM. SELECT REPLY CODE 10AD06 AETUD /D/ 08LOCATION,INSCRIPTION INSCRIPTION LOCATION INDICATES THE LOCATION OF THE INSCRIPTION ON THE ITEM. SELECT REPLY CODE 10AE46 AETVD /D/ 07CAPABILITY,ALIGNMENT,ROTATABLE ROTATABLE ALIGNMENT CAPABILITY AN INDICATION OF WHETHER OR NOT THE ITEM IS CAPABLE OF BEING ROTATED FOR ALIGNMENT OF LEGEND. SELECT REPLY CODE 10AA89 AETWJ 04LENGTH,PLATEAU PLATEAU LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AETXJ 04WIDTH,PLATEAU PLATEAU WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AETYJ 04HEIGHT,PLATEAU PLATEAU HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AETZJ 04DIAMETER,EFFECTIVE EFFECTIVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AEUAJ 04WIDTH,EFFECTIVE EFFECTIVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEUBJ 04DISTANCE BETWEEN MOUNTING HOLES,CENTER TO CENTER,MAJOR MAJOR CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AEUCJ 04DISTANCE BETWEEN MOUNTING HOLES,CENTER TO CENTER,MINOR MINOR CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AEUDJ 04DISTANCE BETWEEN MOUNTING SLOTS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING SLOTS A MEASUREMENT OF THE CENTER TO CENTER DISTANCE BETWEEN MOUNTING SLOTS. 2D AND 1B MODE REPLY21AA051AC20 AEUED /D/ 19FEATURE,SURFACE,FACE FACE SURFACE FEATURE THE SPECIFIC SURFACE PROPERTY WHICH DIRECTLY AFFECTS THE LIGHT TRANSMISSION OF THE LENS FACE. SELECT REPLY CODE 10AD35 AEUFD /D/ 19FEATURE,SURFACE,BACK BACK SURFACE FEATURE THE SPECIFIC SURFACE PROPERTY WHICH DIRECTLY AFFECTS THE LIGHT TRANSMISSION OF THE LENS BACK. SELECT REPLY CODE 10AD35 AEUGD /D/ 09MATERIAL,SHELL SHELL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHELL IS FABRICATED. PLEASE USE MRC CSPT OR MATT WITH ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AEUHA 12QUANTITY,ACCOMMODATION,LAMP LAMP ACCOMMODATION QUANTITY THE NUMBER OF LAMPS THAT CAN BE ACCOMMODATED BY THE ITEM. 1A MODE REPLY 0 AEUJD 18TYPE ACCOMMODATED,BASE,LAMP LAMP BASE TYPE ACCOMMODATED INDICATES THE TYPE OF LAMP BASE THE ITEM WILL ACCOMMODATE. SELECT REPLY CODE 10AD36 AEUKD /D/ 07SHELL SHELL AN INDICATION OF WHETHER OR NOT AN OUTER PORTION DESIGNED TO ENCLOSE OR PARTIALLY ENCLOSE THE BODY OF THE ITEM IS INCLUDED. SELECT REPLY CODE 10AA49 AEULD /D/ 07CAP,MOUNTING MOUNTING CAP AN INDICATION OF WHETHER OR NOT A MOUNTING CAP IS INCLUDED. SELECT REPLY CODE 10AA49 AEUMD /D/ 02DESIGN,CAP CAP DESIGN THE PARTICULAR PREFORMED SHAPE OF THE CAP. SELECT REPLY CODE 10AC46 AEUND /D/ 11METHOD,MOUNTING,CAP CAP MOUNTING METHOD THE MEANS OF ATTACHING THE CAP. SELECT REPLY CODE 10AB89 AEUPD /D/ 19POSITION,BRACKET,MOUNTING MOUNTING BRACKET POSITION THE POSITION OF THE BRACKET MOUNTING SURFACE IN RELATIONSHIP TO THE ITEM WHEN THE ITEM IS IN A VERTICAL POSITION. SELECT REPLY CODE 10AC60 AEUQA /D/ 16STYLE,CLIP,MOUNTING MOUNTING CLIP STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE MOUNTING CLIP. 1A MODE REPLY 0 AEURJ 04HEIGHT,CLIP CLIP HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AEUSJ 04LENGTH,CLIP CLIP LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEUTD /D/ 07SOCKET,STARTER STARTER SOCKET AN INDICATION OF WHETHER OR NOT A STARTER SOCKET IS INCLUDED. SELECT REPLY CODE 10AA49 AEUUD 19PROVISION,MOUNTING,ACCESSORY ACCESSORY MOUNTING PROVISION THE PROVISIONS FURNISHED FOR MOUNTING ACCESSORIES IN OR ON THE ITEM. SELECT REPLY CODE 10AD37 AEUVD /D/ 07STRIP,MOUNTING MOUNTING STRIP AN INDICATION OF WHETHER OR NOT A STRIP TO BE USED AS A MEANS OF ATTACHING THE ITEM IS INCLUDED. PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AEUWA /D/ 16STYLE,BRACKET,MOUNTING MOUNTING BRACKET STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE MOUNTING BRACKET. 1A MODE REPLY 0 AEUXD /D/ 18TYPE,CAP CAP TYPE INDICATES THE TYPE OF CAP FURNISHED WITH THE ITEM. PLEASE USE MRC BRWN IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD39 AEUYJ 04DISTANCE FROM BORE CENTERLINE TO END DISTANCE FROM BORE CENTERLINE TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AEUZJ 04LENGTH,DIAMETER,LARGEST LARGEST DIAMETER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEVAJ T10RANGE,PRESSURE,OUTLET OUTLET PRESSURE RANGE THE MINIMUM TO MAXIMUM LIMITS OF OUTLET PRESSURE OF THE ITEM. 1D AND 1F MODE REPLY11AB18 AEVBL 16STYLE,HOLE,MOUNTING MOUNTING HOLE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE MOUNTING HOLE(S). 1L MODE REPLY 0 AEVCA 12QUANTITY,KEY KEY QUANTITY THE NUMBER OF KEYS CONTAINED IN OR ON THE ITEM. 1A MODE REPLY 0 AEVDJ 04DISTANCE FROM CENTER OF BORE TO TOP OF KEY DISTANCE FROM CENTER OF BORE TO TOP OF KEY THE DISTANCE FROM THE CENTER OF THE BORE TO THE TOP OF THE KEY/S/. 2D AND 1B MODE REPLY21AA051AC20 AEVEA 12QUANTITY,KEYWAY KEYWAY QUANTITY THE NUMBER OF KEYWAYS CONTAINED IN OR ON THE ITEM. 1A MODE REPLY 0 AEVFJ 04DISTANCE FROM CENTER OF BORE TO BOTTOM OF KEYWAY DISTANCE FROM CENTER OF BORE TO BOTTOM OF KEYWAY THE DISTANCE FROM THE CENTER OF THE BORE TO THE BOTTOM OF THE KEYWAY(S). 2D AND 1B MODE REPLY21AA051AC20 AEVGB 04SPACING IN DEG,KEY KEY SPACING IN DEG A MEASUREMENT OF THE AMOUNT OF TURNING NECESSARY TO BRING ONE KEY INTO COINCIDENCE WITH ANOTHER,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AEVHD 18TYPE,BALANCE BALANCE TYPE INDICATES THE TYPE OF BALANCE THAT HAS BEEN APPLIED TO THE ITEM. SELECT REPLY CODE 10AG83 AEVJB 04SPACING IN DEG,KEYWAY KEYWAY SPACING IN DEG A MEASUREMENT OF THE AMOUNT OF TURNING NECESSARY TO BRING ONE KEYWAY INTO COINCIDENCE WITH ANOTHER,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AEVKJ /D/ 10PRESSURE RATING PRESSURE RATING THE PRESSURE AT WHICH AN ITEM IS DESIGNED TO OPERATE. 2D AND 1B MODE REPLY21AB181AC20 AEVLD /D/ 11METHOD,ACTUATING,VALVE VALVE ACTUATING METHOD THE MEANS USED TO CONTROL A VALVE OPENING. SELECT REPLY CODE 10AD49 AEVMD 19ACTION,VALVE,TWO-WAY TWO-WAY VALVE ACTION AN INDICATION OF THE ACTION OF A TWO-WAY VALVE. SELECT REPLY CODE 10AD44 AEVND 18TYPE,REGULATION REGULATION TYPE INDICATES THE BASIC DESIGN TYPE USED FOR REGULATING THE ITEM. SELECT REPLY CODE 10AD45 AEVPD /D/ 11METHOD,CONTROL,MANUAL MANUAL CONTROL METHOD THE MEANS USED TO MANUALLY ADJUST THE ITEM. SELECT REPLY CODE 10AC58 AEVQD 02DESIGN,STEM,VALVE VALVE STEM DESIGN THE SEAT DESIGN OF THE VALVE STEM. SELECT REPLY CODE 10AD46 AEVRD 11METHOD,LOADING,VALVE VALVE LOADING METHOD THE MEANS OF PROVIDING RESISTANCE TO THE MEDIA PASSING THROUGH A VALVE,WHEREBY THE VALVE IS ACTUATED TO REGULATE THE FLOW. SELECT REPLY CODE 10AC63 AEVSD 11METHOD,ACTUATION,REMOTE REMOTE ACTUATION METHOD THE MEANS WHEREBY A VALVE IS ACTUATED OTHER THAN BY THE MEDIA PASSING THROUGH IT. SELECT REPLY CODE 10AD04 AEVTJ 04LENGTH,TUBE,CAPILLARY CAPILLARY TUBE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CAPILLARY TUBE. 2D AND 1B MODE REPLY21AA051AC20 AEVUJ 04LENGTH,BULB BULB LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A BULB. 2D AND 1B MODE REPLY21AA051AC20 AEVVJ 04DIAMETER,BULB BULB DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BULB,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AEVWD /D/ 09MATERIAL,BULB BULB MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BULB IS FABRICATED. SELECT REPLY CODE 10AD09 AEVXD 07ADJUSTABILITY,TEMP TEMP ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE TEMPERATURE IS ADJUSTABLE. SELECT REPLY CODE 10AC06 AEVYJ /D/ 10TEMP RATING,ELEMENT ELEMENT TEMP RATING A VALUE WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AS APPLIED TO THE OPERATION,OR LIMITATION OF OPERATION,OF AN ITEM. 1D AND 1B MODE REPLY11AB36 AEVZJ 10PRESSURE RATING,INLET,MAXIMUM MAXIMUM INLET PRESSURE RATING THE MAXIMUM PRESSURE OF THE MEDIA ON THE INLET SIDE AT WHICH AN ITEM IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY11AB18 AEWAJ 10SETTING,PRESSURE,OUTLET OUTLET PRESSURE SETTING THE SET /NONADJUSTABLE/ PRESSURE OF THE MEDIA ON THE OUTLET SIDE. 1D AND 1B MODE REPLY11AB18 AEWBJ 10ACCURACY RATING,PRESSURE,OUTLET OUTLET PRESSURE ACCURACY RATING THE RATED VARIANCE OF THE OUTLET PRESSURE FROM THE SET PRESSURE. 1D AND 1B MODE REPLY11AB18 AEWCD /D/ 07BY-PASS BY-PASS AN INDICATION OF WHETHER OR NOT A BY-PASS FOR THE ITEM IS INCLUDED. SELECT REPLY CODE 10AA49 AEWDJ 10FLOW RATE,BYPASS BYPASS FLOW RATE THE RATED BYPASS DISCHARGE CAPACITY PER UNIT OF TIME. 1D AND 1B MODE REPLY11AC64 AEWEJ 10PRESSURE RATING,INLET,BYPASS BYPASS INLET PRESSURE RATING THE RATED PRESSURE OF THE MEDIA ON THE INLET SIDE OF THE BYPASS. 2D AND 1B MODE REPLY21AB181AC20 AEWFD /D/ 07FILTER FILTER AN INDICATION OF WHETHER OR NOT A FILTER IS INCLUDED. SELECT REPLY CODE 10AA49 AEWGJ 04DIAMETER,OUTSIDE,DIAL DIAL OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DIAL,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AEWHF T10RANGE,DIAL DIAL RANGE THE MINIMUM AND MAXIMUM LIMITS OF VARIATION IN CAPACITY THAT A DIAL WILL MEASURE. 1F MODE REPLY 0 AEWJD 19ELEMENT,THERMOSTATIC THERMOSTATIC ELEMENT THE BASIC DESIGN TYPE OF THE THERMOSTATIC ELEMENT USED IN TRANSMITTING THE TEMPERATURE OF A LIQUID OR GAS. SELECT REPLY CODE 10AD47 AEWKJ 10CURRENT RATING,MAXIMUM MAXIMUM CURRENT RATING THE MAXIMUM CONTINUOUS CURRENT WHICH MUST NOT BE EXCEEDED IN ORDER TO AVOID DAMAGE TO THE ITEM. 1D AND 1B MODE REPLY11AC30 AEWLD /D/ 19MEDIUM,COOLING,ENVIRONMENTAL ENVIRONMENTAL COOLING MEDIUM THE ENVIRONMENTAL COOLING MEDIUM IN WHICH THE THERMAL TIME CONSTANT AND DISSIPATION CONSTANT OF THE ITEM ARE DETERMINED. SELECT REPLY CODE 10AB75 AEWMJ 10RESISTANCE,HEATER HEATER RESISTANCE THE OHMIC VALUE OF THE RESISTANCE OF THE HEATER ELEMENT TO THE FLOW OF DIRECT CURRENT. 1D AND 1B MODE REPLY11AA57 AEWNF T10TOLERANCE IN PERCENT,RESISTANCE,HEATER HEATER RESISTANCE TOLERANCE IN PERCENT THE LIMITS OF PERMISSIBLE VARIATION IN THE ELECTRICAL RESISTANCE VALUE FROM THE RATED VALUE OF THE HEATER ELEMENT,EXPRESSED IN PERCENT. 1F MODE REPLY 0 AEWPD /D/ 19SOURCE,POWER,ILLUMINATION ILLUMINATION POWER SOURCE THE MEDIUM FURNISHING THE ENERGY FROM WHICH ILLUMINATION IS OBTAINED. SELECT REPLY CODE 10AE16 AEWQD /D/ 07LAMP LAMP AN INDICATION OF WHETHER OR NOT A LAMP IS INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA49 AEWRA 12QUANTITY,LAMP LAMP QUANTITY THE NUMBER OF LAMPS INCLUDED WITH THE ITEM. 1A MODE REPLY 0 AEWSB 10WATTAGE RATING IN WATTS,LAMP LAMP WATTAGE RATING IN WATTS THE RATED POWER THAT A LAMP CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS. 1B MODE REPLY 0 AEWTL 16STYLE,SHAPE,LAMB BULB LAMP BULB SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE LAMP BULB. 1L MODE REPLY 0 AEWUA 03DESIGNATOR,SIZE,LAMP BULB LAMP BULB SIZE DESIGNATOR THE DESIGNATION THAT DESCRIBES THE SIZE AND CONFIGURATION OF A LAMP BULB. 1A MODE REPLY 0 AEWVL 16STYLE,BASE,LAMP LAMP BASE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE BASE OF THE LAMP. 1L MODE REPLY 0 AEWWB 10CANDLEPOWER RATING IN FOOTCANDLES,LAMP LAMP CANDLEPOWER RATING IN FOOTCANDLES THE CANDLEPOWER,OR MEASUREMENT OF LUMINOUS INTENSITY FOR WHICH THE LAMP IS RATED,EXPRESSED IN FOOTCANDLES. 1B MODE REPLY 0 AEWXB 10VOLTAGE RATING IN VOLTS,LAMP LAMP VOLTAGE RATING IN VOLTS THE VOLTAGE FOR WHICH THE LAMP IS RATED FOR NORMAL OPERATION,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AEWYD 18TYPE,LAMP LAMP TYPE INDICATES THE FORM,CONSTRUCTION,OR TYPE OF LAMP WHICH DISTINGUISHES IT FROM OTHER LIKE ITEMS. SELECT REPLY CODE 10AD48 AEWZD 19TRANSPARENCY,LAMP LAMP TRANSPARENCY THE ABILITY OF THE LAMP OR PORTION OF THE LAMP TO TRANSMIT LIGHT AND ALLOW VISUAL PERCEPTION. SELECT REPLY CODE 10AF93 AEXAD /D/ 18TYPE,UNIT,LAMP LAMP UNIT TYPE INDICATES THE TYPE OF LAMP UNIT USED. SELECT REPLY CODE 10AD50 AEXBD /D/ 07LENS LENS AN INDICATION OF WHETHER OR NOT A TRANSPARENT OR TRANSLUCENT ITEM IS INCLUDED. SELECT REPLY CODE 10AA49 AEXCA 12QUANTITY,LENS LENS QUANTITY THE NUMBER OF LENSES INCLUDED WITH THE ITEM. 1A MODE REPLY 0 AEXDD 01COLOR,LENS LENS COLOR THE HUE OR TINT OF THE LENS. SELECT REPLY CODE 10AD06 AEXEL 16STYLE,LENS LENS STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LENS. 1L MODE REPLY 0 AEXFJ /D/ 04DIAMETER,OVERALL,LENS LENS OVERALL DIAMETER THE LONGEST STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PLANE OF A LENS,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AEXGJ /D/ 04HEIGHT,OVERALL,LENS LENS OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AEXHJ /D/ 04LENGTH,OVERALL,LENS LENS OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEXJJ /D/ 04WIDTH,OVERALL,LENS LENS OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AEXKD 19TRANSPARENCY,LENS LENS TRANSPARENCY THE ABILITY OF THE LENS TO TRANSMIT LIGHT AND ALLOW VISUAL PERCEPTION. SELECT REPLY CODE 10AF93 AEXLA /D/ 12QUANTITY OF BOW POSTS ACCOMMODATED QUANTITY OF BOW POSTS ACCOMMODATED THE NUMBER OF BOW POSTS WHICH THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 AEXMJ 10FORCE,HOLDING HOLDING FORCE THE AMOUNT OF HOLDING POWER APPLIED TO THE DOOR WHEN MAGNETICALLY ACTIVATED. 2D AND 1B MODE REPLY22AG671AC20 AEXND /D/ 07LENS,REFLECTIVE REFLECTIVE LENS AN INDICATION OF WHETHER OR NOT THE LENS IS REFLECTIVE. SELECT REPLY CODE 10AA89 AEXPD /D/ 11METHOD,MOUNTING,LENS HOLDER LENS HOLDER MOUNTING METHOD THE MEANS OF ATTACHING THE LENS HOLDER TO ITS MOUNTED POSITION. SELECT REPLY CODE 10AB89 AEXQD /D/ 07BATTERY BATTERY AN INDICATION OF WHETHER OR NOT A BATTERY/IES/ IS INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA49 AEXRA 12QUANTITY,BATTERY BATTERY QUANTITY THE NUMBER OF BATTERIES REQUIRED FOR OPERATION. 1A MODE REPLY 0 AEXSD 18TYPE,BATTERY BATTERY TYPE INDICATES THE TYPE OF BATTERY(IES) USED. SELECT REPLY CODE 10AD57 AEXTD 19ELECTROLYTE,BATTERY BATTERY ELECTROLYTE THE COMPOSITION OF THE ELECTROLYTE USED IN THE BATTERY. SELECT REPLY CODE 10AD52 AEXUD /D/ 07BATTERY,RECHARGEABLE RECHARGEABLE BATTERY AN INDICATION OF WHETHER OR NOT THE BATTERY IS RECHARGEABLE. SELECT REPLY CODE 10AA89 AEXVJ 04LENGTH,BASE,MOUNTING MOUNTING BASE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING BASE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AEXWJ 04WIDTH,BASE,MOUNTING MOUNTING BASE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING BASE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AEXXJ 04HEIGHT,BASE,MOUNTING MOUNTING BASE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE MOUNTING BASE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AEXYJ 04DIAMETER,BASE,MOUNTING MOUNTING BASE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MOUNTING BASE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AEXZJ 04DIAMETER,HOLE,PANEL ACCOMMODATION PANEL ACCOMMODATION HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE PANEL OPENING FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AEYAJ /D/ 04THICKNESS,MAXIMUM,PANEL ACCOMMODATION PANEL ACCOMMODATION MAXIMUM THICKNESS THE MAXIMUM MEASUREMENT OF THE SMALLEST DIMENSION OF THE ACCOMMODATION FOR THE PANEL FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 AEYBD 11METHOD,PROVISION,WIRING WIRING PROVISION METHOD THE MEANS PROVIDED FOR ELECTRICAL CONNECTION OF THE ITEM TO A POWER SOURCE. SELECT REPLY CODE 10AD53 AEYCA 12QUANTITY,FILTER FILTER QUANTITY THE NUMBER OF FILTERS INCLUDED WITH THE ITEM. 1A MODE REPLY 0 AEYDA /D/ 12QUANTITY,APERTURE,FILTER FILTER APERTURE QUANTITY THE NUMBER OF FILTER APERTURES PROVIDED. 1A MODE REPLY 0 AEYED /D/ 14SHAPE,APERTURE,FILTER FILTER APERTURE SHAPE THE PHYSICAL CONFIGURATION OF THE FILTER APERTURE. SELECT REPLY CODE 10AD07 AEYFJ 04LENGTH,APERTURE,FILTER FILTER APERTURE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A FILTER APERTURE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AEYGJ 04WIDTH,APERTURE,FILTER FILTER APERTURE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FILTER APERTURE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AEYHJ 04DIAMETER,APERTURE,FILTER FILTER APERTURE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FILTER ORIFICE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AEYJD 18TYPE,DEVICE,ILLUMINATION DIRECTING ILLUMINATION DIRECTING DEVICE TYPE INDICATES THE TYPE OF DEVICE OTHER THAN THE LENS USED TO DIRECT ILLUMINATION. SELECT REPLY CODE 10AD54 AEYKD /D/ 09MATERIAL,DEVICE,ILLUMINATION DIRECTING ILLUMINATION DIRECTING DEVICE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ILLUMINATION DIRECTING DEVICE IS FABRICATED. SELECT REPLY CODE 10AD09 AEYLD /D/ 17SURFACE TREATMENT,DEVICE,ILLUMINATION DIRECTING ILLUMINATION DIRECTING DEVICE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE ILLUMINATION DIRECTING DEVICE SURFACE. SELECT REPLY CODE 10AD09 AEYMD 19MOTION,BEAM,LIGHT LIGHT BEAM MOTION THE PATTERN OF MOTION OF THE LIGHT BEAM WHEN IN OPERATION. SELECT REPLY CODE 10AD55 AEYND /D/ 07FILTER,LIGHT LIGHT FILTER AN INDICATION OF WHETHER OR NOT A DEVICE THAT PARTIALLY OR COMPLETELY ABSORBS CERTAIN LIGHT RAYS IS INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA49 AEYPD /D/ 19SPREAD,BEAM,LIGHT LIGHT BEAM SPREAD AN INDICATION OF WHETHER OR NOT THE ILLUMINATED AREA CAN BE VARIED. SELECT REPLY CODE 10AD30 AEYQD /D/ 07ADJUSTMENT,LIGHT LIGHT ADJUSTMENT AN INDICATION OF WHETHER OR NOT THE LIGHT MAY BE PHYSICALLY ADJUSTED WITHOUT CHANGING THE MOUNTING. SELECT REPLY CODE 10AA89 AEYRD 11METHOD,ADJUSTMENT,LIGHT LIGHT ADJUSTMENT METHOD THE MEANS OF CHANGING THE DIRECTION OF THE ILLUMINATING SOURCE WITHOUT CHANGING THE MOUNTING. SELECT REPLY CODE 10AD58 AEYSD /D/ 08LOCATION,ADJUSTMENT,LIGHT LIGHT ADJUSTMENT LOCATION INDICATES THE LOCATION(S) FOR ADJUSTING THE LIGHT. SELECT REPLY CODE 10AE46 AEYTJ 10LIMITS,ADJUSTMENT,LIGHT LIGHT ADJUSTMENT LIMITS THE DIMENSIONAL LIMITS TO WHICH THE LIGHT WILL ADJUST. 2D AND 1B MODE REPLY21AA051AC20 AEYUB /D/ 10LIMIT IN DEG,ADJUSTMENT,LIGHT LIGHT ADJUSTMENT LIMIT IN DEG THE LIMIT TO WHICH THE LIGHT WILL ADJUST,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AEYVD /D/ 07DEVICE,LOCKING,LIGHT ADJUSTMENT LIGHT ADJUSTMENT LOCKING DEVICE AN INDICATION OF WHETHER OR NOT A LIGHT ADJUSTMENT LOCKING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 AEYWD /D/ 14SHAPE,REFLECTOR REFLECTOR SHAPE THE PHYSICAL CONFIGURATION OF THE REFLECTOR. SELECT REPLY CODE 10AD07 AEYXD /D/ 09MATERIAL,REFLECTOR REFLECTOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE REFLECTOR IS FABRICATED. SELECT REPLY CODE 10AD09 AEYYD /D/ 17SURFACE TREATMENT,REFLECTOR REFLECTOR SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE REFLECTOR SURFACE. SELECT REPLY CODE 10AD09 AEYZD /D/ 19DEVICE,PROTECTION,LAMP/LENS LAMP/LENS PROTECTION DEVICE THE MEANS PROVIDED TO PROTECT THE LAMP AND/OR LENS FROM DAMAGE. SELECT REPLY CODE 10AD60 AEZAD /D/ 11METHOD,BLACKOUT BLACKOUT METHOD THE DEVICE PROVIDED FOR RESTRICTING ILLUMINATION. SELECT REPLY CODE 10AD61 AEZBD /D/ 01COLOR,OPENING,BLACKOUT BLACKOUT OPENING COLOR THE HUE OR TINT OF THE ILLUMINATION EMITTED THROUGH THE BLACKOUT OPENING. SELECT REPLY CODE 10AD06 AEZCA /D/ 12QUANTITY,OPENING,BLACKOUT BLACKOUT OPENING QUANTITY THE NUMBER OF OPENINGS IN THE BLACKOUT DEVICE. 1A MODE REPLY 0 AEZDD /D/ 07SWITCH SWITCH AN INDICATION OF WHETHER OR NOT A DEVICE USED TO OPEN OR CLOSE AN ELECTRICAL CIRCUIT IS INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA49 AEZED /D/ 07CHANGER,LAMP,AUTOMATIC AUTOMATIC LAMP CHANGER AN INDICATION OF WHETHER OR NOT AN AUTOMATIC LAMP CHANGER IS INCLUDED. SELECT REPLY CODE 10AA49 AEZFD 18TYPE,CIRCUIT CIRCUIT TYPE INDICATES THE TYPE OF PATH OVER WHICH AN ELECTRIC CURRENT CAN FLOW. SELECT REPLY CODE 10AD62 AEZGD /D/ 07LIGHT,RETRACTABLE RETRACTABLE LIGHT AN INDICATION OF WHETHER OR NOT THE LIGHT IS RETRACTABLE. SELECT REPLY CODE 10AA89 AEZHJ /D/ 04ANGLE IN DEG,ARC,VISIBILITY VISIBILITY ARC ANGLE IN DEG THE NUMBER OF DEGREES OF ARC THE EMITTED LIGHT IS VISIBLE. 1D AND 1B MODE REPLY13AC60 AEZJD /D/ 07CIRCUIT,REGULATOR,CURRENT CURRENT REGULATOR CIRCUIT AN INDICATION OF WHETHER OR NOT A MEANS FOR REGULATING THE FLOW OF CURRENT IS INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA49 AEZKD /D/ 18TYPE,SIGNAL,BEAM BEAM SIGNAL TYPE INDICATES THE TYPE OF BEAM SIGNAL (BLINKING,CODING,OR FLASHING) THE ITEM PROVIDES IN ITS FUNCTION. SELECT REPLY CODE 10AD63 AEZLD 11METHOD,SIGNAL,BEAM BEAM SIGNAL METHOD THE MEANS USED TO INTERRUPT THE BEAM. SELECT REPLY CODE 10AD64 AEZMD 08LOCATION,CONTROL,BEAM SIGNAL BEAM SIGNAL CONTROL LOCATION INDICATES THE LOCATION OF CONTROL OF THE BEAM SIGNAL. SELECT REPLY CODE 10AD65 AEZND /D/ 18TYPE,ARC,CARBON CARBON ARC TYPE INDICATES THE TYPE OF CARBON ARC PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AD66 AEZPD /D/ 07PROVISION,RESISTOR RESISTOR PROVISION AN INDICATION OF WHETHER OR NOT ELECTRICAL IMPEDANCE IN THE FORM OF A RESISTOR IS INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA49 AEZQD /D/ 08LOCATION,PROVISION,RESISTOR RESISTOR PROVISION LOCATION AN INDICATION OF WHETHER THE LOCATION OF THE RESISTOR PROVISION IS INTERNAL OR EXTERNAL. SELECT REPLY CODE 10AE46 AEZRA 12QUANTITY,RESISTOR RESISTOR QUANTITY THE NUMBER OF RESISTORS INCLUDED WITH THE ITEM. 1A MODE REPLY 0 AEZSD 18TYPE,CIRCUIT,MULTILAMP MULTILAMP CIRCUIT TYPE INDICATES THE TYPE OF CIRCUIT USED IN THE INTERNAL WIRING OF A LIGHT WITHIN A MULTIPLE LAMP DISPLAY. SELECT REPLY CODE 10AD67 AEZTA /D/ 12QUANTITY,TRANSISTOR TRANSISTOR QUANTITY THE NUMBER OF TRANSISTORS INCLUDED WITH THE ITEM. 1A MODE REPLY 0 AEZUD /D/ 19MEMBER ACCOMMODATED,MATING,ELECTRICAL CONNENTOR RECEPTACLE ELECTRICAL CONNENTOR RECEPTACLE MATING MEMBER ACCOMMODATED THE MATING MEMBER ACCOMMODATED BY THE ELECTRICAL CONNECTOR RECEPTACLE /CONVENIENCE OUTLET/ PROVIDED ON THE ITEM. SELECT REPLY CODE 10AA58 AEZVD /D/ 07OPERATION,RELAY,AUTOMATIC SWITCHING AUTOMATIC SWITCHING RELAY OPERATION AN INDICATION OF WHETHER OR NOT AN AUTOMATIC SWITCHING RELAY OPERATION IS INCLUDED. SELECT REPLY CODE 10AA49 AEZWD 18TYPE,SIGNAL,TRAFFIC TRAFFIC SIGNAL TYPE INDICATES THE TYPE OF TRAFFIC THE SIGNAL IS DESIGNED TO CONTROL. SELECT REPLY CODE 10AD69 AEZXD /D/ 07TRANSFORMER TRANSFORMER AN INDICATION OF WHETHER OR NOT A TRANSFORMER IS PROVIDED. SELECT REPLY CODE 10AB22 AEZYJ /D/ 04DIAMETER,APERTURE APERTURE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ORIFICE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AEZZD 11METHOD,COUNTERBALANCE,SUSPENSION LIGHT LIGHT SUSPENSION COUNTERBALANCE METHOD THE MEANS PROVIDED FOR SUSPENDING AND BALANCING AN ITEM. SELECT REPLY CODE 10AD70 AFAAD /D/ 14SHAPE,ELEMENT,BAR BAR ELEMENT SHAPE THE PHYSICAL CONFIGURATION OF THE HEAT ELEMENT. SELECT REPLY CODE 10AD07 AFABJ /D/ 04LENGTH,ELEMENT,BAR BAR ELEMENT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A BAR ELEMENT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AFACJ /D/ 04WIDTH,ELEMENT,BAR BAR ELEMENT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BAR ELEMENT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AFADJ /D/ 04HEIGHT,ELEMENT,BAR BAR ELEMENT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A BAR ELEMENT,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AFAEJ /D/ 04DIAMETER,ELEMENT,BAR BAR ELEMENT DIAMETER A MEASUREMENT OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BAR ELEMENT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AFAFA /D/ 16STYLE ACCOMMODATED,BASE,ELEMENT BAR ELEMENT BAR BASE STYLE ACCOMMODATED THE BAR ELEMENT BASE STYLE FOR WHICH THE ITEM IS ACCOMMODATED. 1A MODE REPLY 0 AFAGD /D/ 07SUPPLY,POWER,EMERGENCY EMERGENCY POWER SUPPLY AN INDICATION OF WHETHER OR NOT AN EMERGENCY POWER SUPPLY IS INCLUDED. SELECT REPLY CODE 10AA49 AFAHD /D/ 09MATERIAL,HEADBAND HEADBAND MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HEADBAND IS FABRICATED. SELECT REPLY CODE 10AD09 AFAJD /D/ 11METHOD,ATTACHMENT,LAMP HOUSING LIGHT CONDUCTOR LAMP HOUSING LIGHT CONDUCTOR ATTACHMENT METHOD THE MEANS OF ATTACHING A LIGHT CONDUCTOR/S/ TO A /FLASHLIGHT/ LAMP HOUSING. SELECT REPLY CODE 10AB89 AFAKD /D/ 18TYPE,EYEPIECE,MICROSCOPE MICROSCOPE EYEPIECE TYPE INDICATES THE TYPE OF MAGNIFIER EYEPIECE PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AD71 AFALD /D/ 07NOSEPIECE,MICROSCOPE,ADJUSTABLE ADJUSTABLE MICROSCOPE NOSEPIECE AN INDICATION OF WHETHER OR NOT THE MICROSCOPE NOSEPIECE IS ADJUSTABLE. SELECT REPLY CODE 10AA89 AFAMA /D/ 10MAGNIFICATION,MICROSCOPE MICROSCOPE MAGNIFICATION THE TOTAL NUMBER OF TIMES THE IMAGE OR FIELD IS MAGNIFIED. 1A MODE REPLY 0 AFAND /D/ 18TYPE,PEDESTAL,MICROSCOPE MICROSCOPE PEDESTAL TYPE INDICATES THE TYPE OF MOUNTING PEDESTAL PROVIDED FOR THE MICROSCOPE. SELECT REPLY CODE 10AD55 AFAPD /D/ 07SLIT,ADJUSTABLE ADJUSTABLE SLIT AN INDICATION OF WHETHER OR NOT THE SLIT /VIEWING APERTURE/ IS ADJUSTABLE. SELECT REPLY CODE 10AA89 AFAQJ /D/ 04LENGTH,SLIT SLIT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SLIT /VIEWING APERTURE/,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AFARD /D/ 09MATERIAL,FASTENER FASTENER MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE FASTENER IS FABRICATED. SELECT REPLY CODE 10MA01 AFASD /D/ 07TOP WITH SHIELD,REMOVABLE REMOVABLE TOP WITH SHIELD AN INDICATION OF WHETHER OR NOT A REMOVABLE TOP WITH SHIELD IS INCLUDED. SELECT REPLY CODE 10AA49 AFATD /D/ 07HOLDER,STANDARD,COLOR,REVOLVING DISK REVOLVING DISK COLOR STANDARD HOLDER AN INDICATION OF WHETHER OR NOT A REVOLVING DISK USED TO POSITION THE COLOR STANDARDS IS INCLUDED. SELECT REPLY CODE 10AA49 AFAUD /D/ 07FEATURE,ILLUMINATION,X-RAY FILM X-RAY FILM ILLUMINATION FEATURE AN INDICATION OF WHETHER OR NOT AN ILLUMINATION FEATURE FOR VIEWING X-RAY FILM IS INCLUDED. SELECT REPLY CODE 10AA49 AFAVD /D/ 07REEL,RETRACTABLE RETRACTABLE REEL AN INDICATION OF WHETHER OR NOT A RETRACTABLE REEL IS INCLUDED. SELECT REPLY CODE 10AA49 AFAWD /D/ 07ACCOMMODATION INCLUDED,LAMP LAMP ACCOMMODATION INCLUDED AN INDICATION OF WHETHER OR NOT PROVISIONS FOR A LAMP/S/ IS INCLUDED ON THE ITEM. SELECT REPLY CODE 10AA89 AFAXA 19NUMBER,INDUSTRY,LAMP LAMP INDUSTRY NUMBER THE MEANS ESTABLISHED TO IDENTIFY THE LAMP BY AN INDUSTRY STANDARD NUMBER. 1A MODE REPLY 0 AFAYD /D/ 07ACCOMMODATION INCLUDED,LENS LENS ACCOMMODATION INCLUDED AN INDICATION OF WHETHER OR NOT PROVISIONS FOR A LENS IS INCLUDED ON THE ITEM. SELECT REPLY CODE 10AA89 AFAZD /D/ 07ACCOMMODATION INCLUDED,BATTERY BATTERY ACCOMMODATION INCLUDED AN INDICATION OF WHETHER OR NOT PROVISIONS FOR A BATTERY/IES/ IS INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA89 AFBAD /D/ 07BATTERY,REPLACEABLE REPLACEABLE BATTERY AN INDICATION OF WHETHER OR NOT THE BATTERY IS REPLACEABLE. SELECT REPLY CODE 10AA89 AFBBA /D/ 19SIZE,BATTERY,AMERICAN STANDARDS ASSOCIATION AMERICAN STANDARDS ASSOCIATION BATTERY SIZE THE BATTERY SIZE DESIGNATION AS DETERMINED BY THE AMERICAN STANDARDS ASSOCIATION. 1A MODE REPLY 0 AFBCD /D/ 07ACCOMMODATION INCLUDED,FILTER,LIGHT LIGHT FILTER ACCOMMODATION INCLUDED AN INDICATION OF WHETHER OR NOT PROVISIONS FOR A LIGHT FILTER ARE INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA89 AFBDD /D/ 07FILTER,LIGHT,REMOVABLE REMOVABLE LIGHT FILTER AN INDICATION OF WHETHER OR NOT THE LIGHT FILTER IS REMOVABLE. SELECT REPLY CODE 10AA89 AFBED /D/ 18TYPE,HOLDER,FILTER FILTER HOLDER TYPE INDICATES THE TYPE OF FILTER HOLDER PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AD74 AFBFJ /D/T10RANGE,DIAL,TEMP TEMP DIAL RANGE THE LIMITS OF VARIATION IN TEMPERATURE THAT A DIAL WILL MEASURE. 1D AND 1F MODE REPLY11AB36 AFBGJ /D/ 10BAND,TRANSMISSION,FILTER FILTER TRANSMISSION BAND THE VALUE OF THE WAVELENGTH OF LIGHT TRANSMISSION ALLOWED TO PASS THROUGH AN ITEM. 2D AND 1B MODE REPLY21AD751AC20 AFBHA 12QUANTITY,SECTION,INDIVIDUAL INDIVIDUAL SECTION QUANTITY THE NUMBER OF INDIVIDUAL SECTIONS INCLUDED IN THE ITEM. 1A MODE REPLY 0 AFBJD /D/ 07SIMILARITY,SECTION SECTION SIMILARITY AN INDICATION OF WHETHER OR NOT ALL SECTIONS OF AN ITEM ARE IDENTICAL. SELECT REPLY CODE 10AA37 AFBKH /D/ 08LOCATION PER SECTION,SWITCH,CAM ACTUATED CAM ACTUATED SWITCH LOCATION PER SECTION THE PHYSICAL LOCATION/S/ OF THE SWITCH/ES/ OF A CAM ACTUATED TYPE ITEM. 2D MODE REPLY 22AD761AD77 AFBLJ /D/A12QUANTITY PER SECTION,SWITCH,CAM ACTUATED CAM ACTUATED SWITCH QUANTITY PER SECTION THE NUMBER OF INDIVIDUAL SWITCHES THAT ARE USED IN CONJUNCTION WITH A ROTATING CAM TO ACCOMPLISH THE SWITCHING FUNCTION OF THE ITEM. 2D AND 1A MODE REPLY22AD761AD77 AFBMH /D/ 19SWITCH PER SECTION,ACTUATED,CAM CAM ACTUATED SWITCH PER SECTION AN INDICATION OF WHETHER OR NOT ALL OF THE CAM ACTUATED SWITCHES ARE IDENTICAL IN PHYSICAL AND ELECTRICAL CONFIGURATION. 3D MODE REPLY 32AD761AD771AA37 AFBNH /D/ 19ACTION PER SECTION,SWITCHING,CAM CAM SWITCHING ACTION PER SECTION AN INDICATION OF WHETHER THE LOBE OF THE ROTATING CAM IS DESIGNED TO ACTUATE /MAKE/ A SWITCH BEFORE OR AFTER THE PRECEDING SWITCH DEACTUATES /BREAKS/. 3D MODE REPLY 32AD761AD771AD78 AFBPH /D/ 02DESIGN PER SECTION,BASIC,CONTACT CONTACT BASIC DESIGN PER SECTION THE GENERAL CONFIGURATION OF THE CONTACT/S/ OF A SWITCH THAT DESCRIBES ITS BASIC SWITCHING STRUCTURE. 3D MODE REPLY 31AD792AD761AD77 AFBQH /D/ 08LOCATION PER SECTION,CONTACT CONTACT LOCATION PER SECTION INDICATES THE PHYSICAL LOCATION OF THE CONTACT/S/. 2D MODE REPLY 22AD761AD77 AFBRH /D/ 19ROTOR THROUGH CONNECTION PER SECTION ROTOR THROUGH CONNECTION PER SECTION THE LOCATION,BY SEGMENT NUMBER,OF THE ROTOR SEGMENT ON THE FRONT SURFACE OF A SECTION THAT IS CONNECTED TO A ROTOR SEGMENT ON THE REAR SURFACE. 6D MODE REPLY 62AD761AD772AD801AD811AD772AD80 AFBSH /D/ 19RELATIONSHIP PER SECTION,POSITION,FRONT TO REAR CONTACT FRONT TO REAR CONTACT POSITION RELATIONSHIP PER SECTION AN INDICATION OF WHETHER OR NOT THE STATIONARY (FIXED) CONTACT POSITIONS ON THE FRONT SURFACE OF THE SECTIONS ARE OFFSET (DISPLACED) FROM THE STATIONARY (FIXED) CONTACT POSITIONS ON THE REAR SURFACE. 2D MODE REPLY 22AD761AB34 AFBTD /D/ 07CASTERS CASTERS AN INDICATION OF WHETHER OR NOT CASTERS ARE INCLUDED WITH THE ITEM. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AFBUA /D/ 12QUANTITY,MATS MATS QUANTITY THE NUMBER OF MATS THE RACK WILL ACCOMMODATE. 1A MODE REPLY 0 AFBVH /D/ 19POSITION PER SECTION,CONTACT,INSULATED STATIONARY INSULATED STATIONARY CONTACT POSITION PER SECTION THE LOCATION,BY CONTACT POSITION NUMBER,OF THE STATIONARY CONTACT ON ONE SURFACE OF THE SECTION THAT IS ELECTRICALLY INSULATED FROM THE CORRESPONDING STATIONARY CONTACT ON THE OPPOSITE SURFACE. 2D MODE REPLY 22AD762AD83 AFBWH /D/ 19ARRANGEMENT,CONTACT,NONSYMMETRICAL NONSYMMETRICAL CONTACT ARRANGEMENT THE CONTACT CONFIGURATION AT EACH CONTACT POSITION OF A SECTION THAT COLLECTIVELY DESCRIBES A NONSYMMETRICAL CONTACT ARRANGEMENT AND ITS SWITCHING ACTION. 4D MODE REPLY 42AD761AD772AD832AE05 AFBXJ /D/A19ARRANGEMENT PER SECTION,FORM,PILE-UP CONTACT PILE-UP CONTACT FORM ARRANGEMENT PER SECTION THE BASIC CONTACT FORMS,IN ORDER OF ASSEMBLAGE,THAT COLLECTIVELY DESCRIBE THE SWITCHING STRUCTURE OF THE PILE-UP CONTACTS. 3D AND 1A MODE REPLY32AD841AD772AD76 AFBYJ /D/A19ARRANGEMENT PER SECTION,CONTACT,CAM ACTUATED SWITCH CAM ACTUATED SWITCH CONTACT ARRANGEMENT PER SECTION THE DESIGNATION THAT IDENTIFIES THE SCHEMATIC DIAGRAM OF THE ELECTRICAL CONFIGURATION OF A SWITCH INCLUDING THE NUMBER OF SWITCHING POLES OR FORMS. 4D AND 1A MODE REPLY42AG282AD841AD772AD76 AFBZJ /D/A12QUANTITY PER SECTION,POLE POLE QUANTITY PER SECTION THE NUMBER OF SWITCHING POLES INCLUDED IN THE CONTACT ARRANGEMENT OF THE ITEM. 2D AND 1A MODE REPLY22AD761AD77 AFCAJ /D/A12QUANTITY PER SECTION,THROW THROW QUANTITY PER SECTION THE NUMBER OF POSITIONS TO WHICH THE SWITCHING POLE/S/ OF THE ITEM MAY BE ACTUATED TO ENERGIZE ELECTRICAL CIRCUITS. 2D AND 1A MODE REPLY22AD761AD77 AFCBH /D/ 19ACTION PER SECTION,SWITCHING,CONTACT CONTACT SWITCHING ACTION PER SECTION AN INDICATION OF WHETHER THE CONTACTS OF THE ITEM ARE DESIGNED TO MAKE BEFORE BREAK/SHORTING/OR BREAK BEFORE MAKE/NONSHORTING/. 3D MODE REPLY 32AD761AD771AD78 AFCDH /D/ 19POSITION PER SECTION,CONTACT,JUMPERED JUMPERED CONTACT POSITION PER SECTION THE LOCATION,BY SECTION NUMBER AND POSITION NUMBER,OF THE CONTACT OF A SWITCH THAT IS ELECTRICALLY INTERCONNECTED BY WIRE LEADS,METALLIC STRIPS/BUSSES/,OR OTHER MEANS. 5D MODE REPLY 52AD762AD831AD822AD762AD83 AFCEH /D/ 19CHARACTERISTIC PER SECTION,SWITCHING,CAM ACTUATED SWITCH CAM ACTUATED SWITCH SWITCHING CHARACTERISTIC PER SECTION THE SWITCHING SEQUENCE OF THE SWITCHES OF A CAM ACTUATED SWITCH,DESIGNATED BY THE POSITION NUMBER OF THE SWITCH/ES/ THAT ACTUATES AT EACH ACTUATOR POSITION OF ROTATION. 4D MODE REPLY 42AD912AD842AD761AD77 AFCFJ /D/ 10VOLTAGE RATING IN VOLTS,CONTACT CONTACT VOLTAGE RATING IN VOLTS THE VOLTAGE FOR WHICH THE CONTACT/S/ IS RATED AT SEA LEVEL OR AT A SPECIFIC ALTITUDE,EXPRESSED IN VOLTS. 3D AND 1B MODE REPLY31AB621AD862AD88 AFCGA 12QUANTITY,ACTUATOR,SWITCH SWITCH ACTUATOR QUANTITY THE NUMBER OF ACTUATORS PROVIDED IN THE ITEM FOR SELECTION OF SWITCHING POSITIONS. 1A MODE REPLY 0 AFCHH /D/ 19SECTION ACTUATED,SWITCH SWITCH SECTION ACTUATED THE SECTION OF THE SWITCH THAT IS ACTUATED BY EACH SHAFT OF MULTIPLE ACTUATORS. 2D MODE REPLY 22AD872AD76 AFCJJ /D/A12QUANTITY,POSITION,SWITCH ACTUATOR INDEXING SWITCH ACTUATOR INDEXING POSITION QUANTITY THE TOTAL NUMBER OF POSITIONS TO WHICH THE SWITCH ACTUATOR MAY BE INDEXED. 1D AND 1A MODE REPLY12AD87 AFCKH /D/ 19POSITION,MOMENTARY,SWITCH ACTUATOR SWITCH ACTUATOR MOMENTARY POSITION THE POSITION OF THE ACTUATOR,WITH RELATION TO THE EXTREMITY OF ROTATION,THAT IS MOMENTARY/SPRING LOADED/. 2D MODE REPLY 22AD871AC84 AFCLJ /D/ 10POSITIONING INCREMENT IN DEG,ACTUATOR,SWITCH SWITCH ACTUATOR POSITIONING INCREMENT IN DEG THE INCREMENTS OF ANGULAR ROTATION THAT THE SWITCH ACTUATOR MOVES BETWEEN ADJACENT INDEX POSITIONS,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY12AD87 AFCMH /D/ 18TYPE,DEVICE,SWITCH ACTUATOR STOP SWITCH ACTUATOR STOP DEVICE TYPE INDICATES THE TYPE OF DEVICE PROVIDED IN THE ITEM TO LIMIT THE ANGULAR ROTATION OF ITS ACTUATOR. 2D MODE REPLY 22AD871AD89 AFCNH /D/ 11METHOD,LOCKING,SWITCH ACTUATOR SWITCH ACTUATOR LOCKING METHOD THE MEANS USED FOR LOCKING THE ACTUATOR. 2D MODE REPLY 22AD871AD90 AFCPH /D/ 19POSITION,LOCKING,SWITCH ACTUATOR SWITCH ACTUATOR LOCKING POSITION THE POSITION OF THE SWITCH ACTUATOR AT WHICH THE LOCKING METHOD IS EFFECTIVE. 2D MODE REPLY 22AD872AD91 AFCQA 19CODE,MANUFACTURER,KNOB KNOB MANUFACTURER CODE THE IDENTIFYING CODE OF THE ORGINATOR THAT CONTROLS OR MANUFACTURERS THE KNOB. 1A MODE REPLY 0 AFCRJ /D/ 10ALTITUDE,VOLTAGE RATING VOLTAGE RATING ALTITUDE THE ALTITUDE AT WHICH THE VOLTAGE RATINGS APPLY. 1D AND 1B MODE REPLY11AA05 AFCSJ /D/ 10CURRENT RATING,LOAD,CONTACT CONTACT LOAD CURRENT RATING THE AMOUNT OF CURRENT THAT THE CONTACTS ARE RATED TO MAKE OR BREAK WITH A SPECIFIED LOAD. 5D AND 1B MODE REPLY51AC301AB621AD921AD862AD88 AFCTJ /D/ 10CURRENT RATING,CONTINUOUS,CONTACT CONTACT CONTINUOUS CURRENT RATING THE AMOUNT OF CURRENT THAT THE CONTACTS ARE RATED TO CARRY IN CONTINUOUS NONMAKE/NONBREAK OPERATION. 3D AND 1B MODE REPLY31AC301AB621AD86 AFCUD 09MATERIAL,PLATE,COOKING COOKING PLATE MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE COOKING PLATE IS FABRICATED. SELECT REPLY CODE 10MA01 AFCVA /D/ 12QUANTITY,SWITCH,AUXILIARY AUXILIARY SWITCH QUANTITY THE NUMBER OF SWITCHES INCLUDED IN THE ITEM TO CONTROL AUXILIARY ELECTRICAL CIRCUITS. 1A MODE REPLY 0 AFCWJ /D/A19ARRANGEMENT,CONTACT,AUXILIARY SWITCH AUXILIARY SWITCH CONTACT ARRANGEMENT THE ELECTRICAL CONFIGURATION OF AN AUXILIARY SWITCH,INCLUDING THE NUMBER OF SWITCHING POLES OR FORMS. 1D AND 1A MODE REPLY12AG28 AFCXD /D/ 07REPLACEABILITY,KNOB KNOB REPLACEABILITY AN INDICATION OF WHETHER OR NOT THE KNOB OF THE ACTUATOR IS REPLACEABLE. SELECT REPLY CODE 10AG84 AFCYA 19NUMBER,PART,KNOB MANUFACTURER KNOB MANUFACTURER PART NUMBER THE IDENTIFYING PART NUMBER ASSIGNED TO THE KNOB. 1A MODE REPLY 0 AFCZG 19MARKINGS,SPECIAL,KNOB KNOB SPECIAL MARKINGS MARKINGS INCLUDED ON THE KNOB FOR THE PURPOSE OF OFFERING INSTRUCTIONS OR WARNINGS OR TO INDICATE THE PURPOSE,FUNCTION,OR APPLICATION OF THE ITEM. EXCLUDES MANUFACTURERS PART NUMBER,SYMBOLS,OR THE LIKE. FULL TEXT WRITE-IN 0 AFDAJ /D/ 08LOCATION IN DEG,ANGULAR,SHAFT FLAT/SLOT SHAFT FLAT/SLOT ANGULAR LOCATION IN DEG THE ANGULAR DISTANCE OF THE SHAFT FLAT OR SLOT FROM THE POINT OF REFERENCE,EXPRESSED IN DEGREES. 2D AND 1B MODE REPLY22AD871AD94 AFDBJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,HOLE,SHAFT SHAFT HOLE THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE THREADED HOLE OF A SHAFT. 2D AND 1A MODE REPLY22AC212AD87 AFDCD 18TYPE,DEVICE,NONTURN NONTURN DEVICE TYPE INDICATES THE TYPE OF DEVICE USED TO PREVENT PHYSICAL MOVEMENT OF THE ITEM ON ITS MOUNTING SURFACE. SELECT REPLY CODE 10AD95 AFDDA /D/ 12QUANTITY,DEVICE,NONTURN NONTURN DEVICE QUANTITY THE NUMBER OF NONTURN DEVICES INCLUDED WITH THE ITEM. 1A MODE REPLY 0 AFDEJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,BUSHING,MOUNTING MOUNTING BUSHING THREAD SIZE AND SERIES TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A MOUNTING BUSHING. 1D AND 1A MODE REPLY12AC21 AFDFJ /D/ 13THREAD LENGTH,BUSHING,MOUNTING MOUNTING BUSHING THREAD LENGTH A MEASUREMENT OF THE DISTANCE THAT THE THREADED MOUNTING BUSHING PROTRUDES FROM THE MOUNTING SURFACE. 2D AND 1B MODE REPLY21AA051AC20 AFDGD /D/ 19PATTERN,MOUNTING MOUNTING PATTERN THE GENERAL CONFIGURATION AND RELATIVE POSITION OF THE HOLES PROVIDED FOR MOUNTING THE ITEM. SELECT REPLY CODE 10AD96 AFDHJ /D/ 13THREAD SIZE AND SERIES/TYPE DESIGNATOR,HOLE,MOUNTING MOUNTING HOLE THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED MOUNTING HOLE. 1D AND 1B MODE REPLY12AC21 AFDJJ /D/ 10VOLTAGE RATING IN KILOVOLTS,WITHSTANDING,DIELECTRIC DIELECTRIC WITHSTANDING VOLTAGE RATING IN KILOVOLTS THE MAXIMUM VOLTAGE THAT THE INSULATING MATERIAL OF THE ITEM WILL WITHSTAND AT SPECIFIED ATMOSPHERIC PRESSURE /ALTITUDE/ LEVELS WITHOUT ARCING,FLASHOVER,BREAKDOWN OF INSULATION,OR OTHER PHYSICAL DAMAGE,EXPRESSED IN KILOVOLTS. 2D AND 1B MODE REPLY21AB621AD86 AFDKJ /D/ 10ALTITUDE,VOLTAGE RATING,DIELECTRIC WITHSTANDING DIELECTRIC WITHSTANDING VOLTAGE RATING ALTITUDE THE ALTITUDE AT WHICH THE DIELECTRIC WITHSTANDING VOLTAGE RATING APPLIES. 1D AND 1B MODE REPLY11AA05 AFDLJ 10FREQUENCY RATING,RADIO,MAXIMUM MAXIMUM RADIO FREQUENCY RATING THE MAXIMUM FREQUENCY AT WHICH THE ITEM IS RATED FOR OPERATION WHEN USED IN RADIO FREQUENCY CIRCUITS. 1D AND 1B MODE REPLY11AC32 AFDMB 10RESISTANCE IN OHMS,CONTACT CONTACT RESISTANCE IN OHMS THE OPPOSITION TO THE FLOW OF CURRENT THROUGH MATING CONTACTS OF AN ITEM,EXPRESSED IN OHMS. 1B MODE REPLY 0 AFDNJ 10AMPLITUDE,RESISTANCE,VIBRATION VIBRATION RESISTANCE AMPLITUDE THE AMPLITUDE OF VIBRATION FOR WHICH THE VIBRATION RESISTANCE FREQUENCY RANGE APPLIES. 1D AND 1B MODE REPLY11AD97 AFDPB 10RESISTANCE RATING IN GRAVITATIONAL UNITS,SHOCK SHOCK RESISTANCE RATING IN GRAVITATIONAL UNITS THE MAXIMUM FORCE AT IMPACT THAT THE ITEM IS RATED TO WITHSTAND,WITHOUT RESULTING IN ANY PERMANENT CHANGE IN PHYSICAL OR ELECTRICAL CHARACTERISTICS,EXPRESSED IN GRAVITATIONAL UNITS /G'S/. 1B MODE REPLY 0 AFDQB /D/ 10TIME IN MILLISECONDS,DURATION,SHOCK PULSE SHOCK PULSE DURATION TIME IN MILLISECONDS THE LENGTH OF TIME,AFTER IMPACT,THAT ESTABLISHES THE CONDITION AT WHICH THE SHOCK RESISTANCE RATING APPLIES,EXPRESSED IN MILLISECONDS. 1B MODE REPLY 0 AFDRJ /D/ 10TORQUE,ROTATIONAL,MINIMUM DETENT MINIMUM DETENT ROTATIONAL TORQUE THE MINIMUM AMOUNT OF TURNING FORCE REQUIRED TO ROTATE A SHAFT THROUGH THE DETENT POSITIONS. 2D AND 1B MODE REPLY21AA562AD87 AFDSJ 04DISTANCE BETWEEN MOUNTING CENTERS,HORIZONTAL,LONGEST LONGEST HORIZONTAL DISTANCE BETWEEN MOUNTING CENTERS THE LONGEST DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE HORIZONTAL PLANE. 2D AND 1B MODE REPLY21AA051AC20 AFDTJ 04DISTANCE BETWEEN MOUNTING CENTERS,HORIZONTAL,SHORTEST SHORTEST HORIZONTAL DISTANCE BETWEEN MOUNTING CENTERS THE SHORTEST DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE HORIZONTAL PLANE. 2D AND 1B MODE REPLY21AA051AC20 AFDUJ 04DISTANCE BETWEEN MOUNTING CENTERS,HORIZONTAL,INTERMEDIATE INTERMEDIATE HORIZONTAL DISTANCE BETWEEN MOUNTING CENTERS THE INTERMEDIATE DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE HORIZONTAL PLANE. 2D AND 1B MODE REPLY21AA051AC20 AFDVJ 04DISTANCE BETWEEN MOUNTING CENTERS,VERTICAL,LONGEST LONGEST VERTICAL DISTANCE BETWEEN MOUNTING CENTERS THE LONGEST DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE VERTICAL PLANE. 2D AND 1B MODE REPLY21AA051AC20 AFDWJ 04DISTANCE BETWEEN MOUNTING CENTERS,VERTICAL,SHORTEST SHORTEST VERTICAL DISTANCE BETWEEN MOUNTING CENTERS THE SHORTEST DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE VERTICAL PLANE. 2D AND 1B MODE REPLY21AA051AC20 AFDXJ /D/ 04DISTANCE BETWEEN MOUNTING CENTERS,VERTICAL,INTERMEDIATE INTERMEDIATE VERTICAL DISTANCE BETWEEN MOUNTING CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AFDYJ /D/ 04DISTANCE BETWEEN SHAFT AND MOUNTING HOLE CENTERLINE,HORIZONTAL HORIZONTAL DISTANCE BETWEEN SHAFT AND MOUNTING HOLE CENTERLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 AFDZJ /D/ 04DISTANCE BETWEEN SHAFT AND MOUNTING HOLE CENTERLINE,VERTICAL VERTICAL DISTANCE BETWEEN SHAFT AND MOUNTING HOLE CENTERLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 AFEAA 12QUANTITY PER ASSEMBLY,BOX BOX QUANTITY PER ASSEMBLY THE NUMBER OF BOXES WHICH COMPRISE A GIVEN ASSEMBLY. 1A MODE REPLY 0 AFEBJ 04DIAMETER,CIRCLE,COVER MOUNTING HOLE COVER MOUNTING HOLE CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFECJ 04DISTANCE FROM CENTER OF MOUNTING HOLE TO EDGE ALONG THE WIDTH DISTANCE FROM CENTER OF MOUNTING HOLE TO EDGE ALONG THE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFEDJ 04DISTANCE FROM CENTER OF MOUNTING HOLE TO EDGE ALONG THE LENGTH DISTANCE FROM CENTER OF MOUNTING HOLE TO EDGE ALONG THE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFEEJ /D/ 04DISTANCE ACROSS FLATS DISTANCE ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 AFEFJ 04DEPTH,INSIDE INSIDE DEPTH AN INSIDE MEASUREMENT BETWEEN SPECIFIED POINTS OF AN ITEM,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AFEGJ /D/ 04LENGTH,LIP,OVERHANG OVERHANG LIP LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFEHJ 04DIAMETER,CIRCLE,BODY MOUNTING HOLE BODY MOUNTING HOLE CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFEJJ 04LENGTH,FEET,MOUNTING MOUNTING FEET LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFEKJ 04THICKNESS,FEET,MOUNTING MOUNTING FEET THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AFELJ 04DISTANCE BETWEEN MOUNTING HOLES,CENTER TO CENTER,THIRD THIRD CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AFEMJ /D/ 04DISTANCE BETWEEN MOUNTING HOLES,CENTER TO CENTER,FOURTH FOURTH CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AFEND /D/ 08LOCATION,ENTRANCE ENTRANCE LOCATION INDICATES THE LOCATION OF THE ENTRANCE/S/ ON THE ITEM. SELECT REPLY CODE 10AE46 AFEPD 03DESIGNATION,NUMERIC,ENTRANCE DIAMETER ENTRANCE DIAMETER NUMERIC DESIGNATOR A NUMERIC DESIGNATION WHICH IDENTIFIES THE NOMINAL DIAMETER OF THE ENTRANCE/S/ PROVIDED ON THE ITEM. SELECT REPLY CODE 10AD98 AFEQA 12QUANTITY,ENTRANCE ENTRANCE QUANTITY THE NUMBER OF ENTRANCES PROVIDED ON THE ITEM. 1A MODE REPLY 0 AFERD 18TYPE,COVER COVER TYPE INDICATES THE TYPE OF COVER AS DISTINGUISHED BY ITS PARTICULAR DESIGN. SELECT REPLY CODE 10AD99 AFESD /D/ 14SHAPE,OPENING,COVER COVER OPENING SHAPE THE PHYSICAL CONFIGURATION OF THE OPENING/S/ PROVIDED IN THE COVER. SELECT REPLY CODE 10AD07 AFETD /D/ 07LENS,COVER COVER LENS AN INDICATION OF WHETHER OR NOT A LENS IS INCLUDED WITH THE COVER. SELECT REPLY CODE 10AA49 AFEUA /D/ 12QUANTITY,OPENING,COVER COVER OPENING QUANTITY THE NUMBER OF OPENINGS PROVIDED ON THE COVER. 1A MODE REPLY 0 AFEVA 12QUANTITY,DEVICE,STANDARD WIRING STANDARD WIRING DEVICE QUANTITY THE NUMBER OF STANDARD WIRING DEVICES,OR THEIR EQUIVALENTS,THE ITEM IS DESIGNED TO MOUNT AND/OR ACCOMMODATE. 1A MODE REPLY 0 AFEWD 07PROVISION,THREAD THREAD PROVISION AN INDICATION OF WHETHER A PORTION/S/ OF THE ITEM IS THREADED OR UNTHREADED. SELECT REPLY CODE 10AE00 AFEXD /D/ 07SIDES,REMOVABLE REMOVABLE SIDES AN INDICATION OF WHETHER OR NOT THE SIDES OF THE ITEM ARE REMOVABLE. SELECT REPLY CODE 10AA89 AFEYD /D/ 07BRACKET,MOUNTING,DETACHABLE DETACHABLE MOUNTING BRACKET AN INDICATION OF WHETHER OR NOT THE MOUNTING BRACKET IS DETACHABLE. SELECT REPLY CODE 10AA89 AFEZD /D/ 07BRACKETS,EAR,PLASTER PLASTER EAR BRACKETS AN INDICATION OF WHETHER OR NOT PREFORMED SHEET METAL BRACKETS FOR WALL PLASTER APPLICATION ARE INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA49 AFFAD /D/ 09MATERIAL,COVER COVER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE COVER IS FABRICATED. PLEASE USE MRC MATT WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AFFBD /D/ 17SURFACE TREATMENT,COVER COVER SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE COVER SURFACE. SELECT REPLY CODE 10AD09 AFFCD /D/ 18TYPE,ACCOMMODATION,RECEPTACLE RECEPTACLE ACCOMMODATION TYPE INDICATES THE TYPE OF ACCOMMODATION INCLUDED TO FACILITATE OR MATE WITH A SPECIFIC RECEPTACLE. SELECT REPLY CODE 10AE01 AFFDD /D/ 07GRIP,CABLE CABLE GRIP AN INDICATION OF WHETHER OR NOT A CABLE GRIP IS INCLUDED. SELECT REPLY CODE 10AA49 AFFEJ /D/ 04DISTANCE BETWEEN OPENINGS,CENTER TO CENTER,VERTICAL VERTICAL CENTER TO CENTER DISTANCE BETWEEN OPENINGS THE DISTANCE MEASURED FROM THE CENTER OF ONE OPENING TO THE CENTER OF ANOTHER OPENING ON THE VERTICAL PLANE. 1D AND 1B MODE REPLY11AA05 AFFFJ /D/ 04DISTANCE BETWEEN OPENINGS,CENTER TO CENTER,HORIZONTAL HORIZONTAL CENTER TO CENTER DISTANCE BETWEEN OPENINGS THE DISTANCE MEASURED FROM THE CENTER OF ONE OPENING TO THE CENTER OF ANOTHER OPENING ON THE HORIZONTAL PLANE. 1D AND 1B MODE REPLY11AA05 AFFGD 11METHOD,ATTACHMENT,COVER COVER ATTACHMENT METHOD THE MEANS PROVIDED FOR ATTACHING THE COVER. SELECT REPLY CODE 10AB47 AFFHD /D/ 13THREAD LOCATION THREAD LOCATION THE PORTION/S/ OF AN ITEM ON WHICH THE THREAD IS LOCATED. SELECT REPLY CODE 10AE46 AFFJJ /D/A16STYLE,SHAFT SHAFT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SHAFT. 1D AND 1A MODE REPLY12AD87 AFFKJ 04LENGTH,SEAM,SIDE SIDE SEAM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SIDE SEAM, IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AFFLJ 04DIAMETER,CIRCLE,BOLT,MOUNTING MOUNTING BOLT CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AFFMA /D/ 16STYLE,JOINT,BOTTOM RING BOTTOM RING JOINT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BOTTOM RING JOINT. 1A MODE REPLY 0 AFFNA /D/ 16STYLE,JOINT,INTERMEDIATE RING INTERMEDIATE RING JOINT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE INTERMEDIATE RING JOINT. 1A MODE REPLY 0 AFFPA /D/ 16STYLE,JOINT,TOP RING TOP RING JOINT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TOP RING JOINT. 1A MODE REPLY 0 AFFQA /D/ 16STYLE,CUT,BOTTOM RING BOTTOM RING CUT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BOTTOM RING CUT. 1A MODE REPLY 0 AFFRA /D/ 16STYLE,CUT,INTERMEDIATE RING INTERMEDIATE RING CUT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARNACE OF THE INTERMEDIATE RING CUT. 1A MODE REPLY 0 AFFSA /D/ 16STYLE,CUT,TOP RING TOP RING CUT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TOP RING CUT. 1A MODE REPLY 0 AFFTA /D/ 16STYLE,SHAPE,CROSS-SECTIONAL,BOTTOM RING BOTTOM RING CROSS-SECTIONAL SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE CROSS-SECTIONAL SHAPE OF THE BOTTOM RING. 1A MODE REPLY 0 AFFUA /D/ 16STYLE,SHAPE,CROSS-SECTIONAL,INTERMEDIATE RING INTERMEDIATE RING CROSS-SECTIONAL SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE CROSS-SECTIONAL SHAPE OF THE INTERMEDIATE RING. 1A MODE REPLY 0 AFFVA /D/ 16STYLE,SHAPE,CROSS-SECTIONAL,TOP RING TOP RING CROSS-SECTIONAL SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE CROSS-SECTIONAL SHAPE OF THE TOP RING. 1A MODE REPLY 0 AFFWJ 04DIAMETER,INSIDE,RETAINER RETAINER INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A RETAINER,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AFFXJ 04DIAMETER,INSIDE,PACKING PACKING INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PACKING,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AFFYD /D/ 08LOCATION,MATERIAL,SEALING ELEMENT SEALING ELEMENT MATERIAL LOCATION INDICATES THE LOCATION OF THE SEALING ELEMENT TO WHICH A SPECIFIC MATERIAL IS APPLICABLE. SELECT REPLY CODE 10AE46 AFFZD /D/ 07KNOB,ACTUATOR ACTUATOR KNOB AN INDICATION OF WHETHER OR NOT AN ACTUATOR KNOB IS INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA49 AFGAJ T10RANGE,TEMP,OPERATING OPERATING TEMP RANGE THE MINIMUM AND MAXIMUM LIMITS OF TEMPERATURE AT WHICH THE ITEM IS RATED FOR OPERATION. 1D AND 1F MODE REPLY11AB36 AFGBJ /D/ 10TORQUE,ROTATIONAL,MAXIMUM DETENT MAXIMUM DETENT ROTATIONAL TORQUE THE MAXIMUM AMOUNT OF TURNING FORCE REQUIRED TO ROTATE A SHAFT THROUGH THE DETENT POSITIONS. 2D AND 1B MODE REPLY21AA562AD87 AFGCD /D/ 14SHAPE,CROSS-SECTIONAL,FLANGE FLANGE CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE FLANGE WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 AFGDD /D/ 14SHAPE,CROSS-SECTIONAL,NUT NUT CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGUARTION OF THE NUT WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 AFGED /D/ 14SHAPE,CROSS-SECTIONAL,BOSS BOSS CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE BOSS WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 AFGFJ 04DIAMETER,POINT,DRIVE DRIVE POINT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFGGJ 04WIDTH ACROSS FLATS,FLANGE FLANGE WIDTH ACROSS FLATS THE SHORTEST STRAIGHT LINE BETWEEN FLATS, PERPENDICULIAR TO THE HEIGHT OF THE FLANGE. 2D AND 1B MODE REPLY21AA051AC20 AFGHJ 04WIDTH ACROSS FLATS,NUT NUT WIDTH ACROSS FLATS A MEASUREMENT OF THE WIDTH ACROSS THE FLATS OF A NUT. 2D AND 1B MODE REPLY21AA051AC20 AFGJJ 04WIDTH ACROSS FLATS,BOSS BOSS WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 AFGKJ 04LENGTH,ACTUATOR ACTUATOR LENGTH THE MEASUREMENT OF THE DISTANCE THAT THE ACTUATOR PROTRUDES FROM THE BODY. 2D AND 1B MODE REPLY21AA051AC20 AFGLJ /D/A19FACTOR PER FUNCTION,QUALITY QUALITY FACTOR PER FUNCTION A MEASURE OF THE QUALITY FACTOR PER FUNCTION OF AN ITEM WITH RESPECT TO A SPECIFIED FREQUENCY FOR THE RATED INDUCTANCE. 2D AND 1A MODE REPLY21AC202AH19 AFGMJ /D/ 10FREQUENCY AT WHICH INDUCTANCE AND QUALITY FACTOR APPLIES PER FUNCTION FREQUENCY AT WHICH INDUCTANCE AND QUALITY FACTOR APPLIES PER FUNCTION THE SPECIFIED FREQUENCY AT WHICH THE INDUCTANCE AND QUALITY OF AN ITEM IS MEASURED,PER FUNCTION. 2D AND 1B MODE REPLY21AC322AH19 AFGNJ 10FREQUENCY AT WHICH IMPEDANCE RATING APPLIES FREQUENCY AT WHICH IMPEDANCE RATING APPLIES THE NUMBER OF PULSES OR THE FREQUENCY AT WHICH THE IMPEDANCE OF AN ITEM IS MEASURED. 1D AND 1B MODE REPLY11AE06 AFGPJ /D/ 10POWER RATING PER FUNCTION,WINDING WINDING POWER RATING PER FUNCTION THE MAXIMUM POWER FOR WHICH THE WINDING PER FUNCTION OF THE ITEM IS RATED. 2D AND 1B MODE REPLY21AC332AH19 AFGQJ T10RANGE RATING,FREQUENCY FREQUENCY RANGE RATING THE RANGE OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH AN ITEM IS RATED. 1D AND 1F MODE REPLY11AC32 AFGRF T10TOLERANCE IN DECIBELS,RESPONSE,FREQUENCY FREQUENCY RESPONSE TOLERANCE IN DECIBELS THE LIMITS OF PERMISSIBLE DEVIATION OVER THE SPECIFIED FREQUENCY RANGE,EXPRESSED IN DECIBELS. 1F MODE REPLY 0 AFGSJ 10FREQUENCY,SELF-RESONANT,MINIMUM MINIMUM SELF-RESONANT FREQUENCY THE MINIMUM FREQUENCY AT WHICH AN ITEM WILL RESONATE WITH COMPLETE ABSENCE OF EXTERNAL CAPACITANCE OR INDUCTANCE. 1D AND 1B MODE REPLY11AC32 AFGTJ /D/ 04GIRTH,HIP HIP GIRTH DESIGNATES THE SIZE OF THE HIP GIRTH. 2D AND 1B MODE REPLY21AA051AC20 AFGUA 19CODE,DESIGNATION,IDENTIFICATION,PACKAGING,STANDARD,UNITED NATIONS UNITED NATIONS STANDARD PACKAGING IDENTIFICATION DESIGNATION CODE A SERIES OF NUMBERS AND LETTERS DESIGNED TO DEFINE THE LEVEL OF PACKAGING REQUIREMENTS UNDER UNITED NATIONS PERFORMANCE-ORIENTED PACKAGING REQUIREMENTS STANDARDS. 1A MODE REPLY 0 AFGVB 10ACCURACY IN PERCENT,LOAD,VOLT-AMPERE VOLT-AMPERE LOAD ACCURACY IN PERCENT THE DEGREE OF VOLT-AMPERE LOAD ACCURACY WHICH THE OUTPUT OF AN ITEM IS DESIGNED TO MAINTAIN,EXPRESSED IN PERCENT. 1B MODE REPLY 0 AFGWJ 19CIRCUMFERENCE,PORTION OF PORTION OF CIRCUMFERENCE A MEASUREMENT OF THE PORTION OF THE CIRCUMFERENCE AS OPPOSED TO A FULL CIRCLE. 1D AND 1B MODE REPLY11AP38 AFGXJ /D/ 04HEIGHT,TERMINAL TERMINAL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AFGYJ /D/ 04LENGTH,LEAD,TERMINAL TERMINAL LEAD LENGTH NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 2D AND 1B MODE REPLY21AA051AC20 AFGZA 19CODE AND PART/MODEL NUMBER,MANUFACTURER,SYSTEM SYSTEM MANUFACTURER CODE AND PART/MODEL NUMBER THE MANUFACTURER'S 5-DIGIT CAGE DESIGNATION AND THE PART/MODEL NUMBER. 1A MODE REPLY 0 AFHAJ /D/ 04DIAMETER,HOLE,CORE ACCOMMODATION CORE ACCOMMODATION HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOLE THAT WILL ACCOMMODATE A CORE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AFHBJ /D/ 04LENGTH,HOLE,CORE ACCOMMODATION CORE ACCOMMODATION HOLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CORE ACCOMMODATION HOLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AFHCJ /D/ 04WIDTH,HOLE,CORE ACCOMMODATION CORE ACCOMMODATION HOLE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CORE ACCOMMODATION HOLE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AFHDJ /D/ 04DIAMETER,OPENING,PRIMARY WINDING PRIMARY WINDING OPENING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PRIMARY WINDING OPENING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AFHEJ /D/ 04WIDTH,OPENING,PRIMARY WINDING PRIMARY WINDING OPENING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A PRIMARY WINDING OPENING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AFHFJ /D/ 04HEIGHT,OPENING,PRIMARY WINDING PRIMARY WINDING OPENING HEIGHT A MEASUREMENT TAKEN FROM THE BOTTOM TO THE TOP OF THE PRIMARY WINDING OPENING,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AFHGD 18TYPE,FACILITY,MOUNTING MOUNTING FACILITY TYPE INDICATES THE TYPE OF FACILITY PROVIDED PERMITTING ATTACHMENT OF THE ITEM TO A SURFACE OR TO ANOTHER ITEM. SELECT REPLY CODE 10AE11 AFHHB 10LIFE RATING,AVERAGE AVERAGE LIFE RATING THE NUMERIC VALUE OF THE LIFE EXPECTANCY OF THE ITEM. 1B MODE REPLY 0 AFHJJ /D/ 04DIAMETER,INSIDE,MOUNTING BUSHING/SLEEVE MOUNTING BUSHING/SLEEVE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFHKJ /D/ 04LENGTH,BUSHING/SLEEVE,MOUNTING MOUNTING BUSHING/SLEEVE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFHLJ /D/ 04DIAMETER,CLIP,MOUNTING MOUNTING CLIP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFHMJ 04WIDTH,TAB,MOUNTING MOUNTING TAB WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A MOUNTING TAB,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AFHNH 19INSTALLATION FOR WHICH DESIGNED INSTALLATION FOR WHICH DESIGNED THE TYPE OF INSTALLATION FOR WHICH THE ITEM IS DESIGNED. 2D MODE REPLY 23AH212AJ17 AFHPJ 04LENGTH OF LONGEST MAST SEGMENT,NOMINAL NOMINAL LENGTH OF LONGEST MAST SEGMENT A MEASUREMENT OF THE NOMINAL DIMENSION OF THE LONGEST OF TWO OR MORE SEGMENTS OF A MAST, IN DISTINCTION FROM WIDTH OR CROSS SECTION, AND PARALLEL TO ITS LONGITUDINAL AXIS. 1D AND 1B MODE REPLY11AA05 AFHQJ /D/ 19INERTIA,ROTOR ROTOR INERTIA THE AMOUNT OF FORCE REQUIRED TO START, STOP OR CHANGE ROTOR DIRECTION. 1D AND 1B MODE REPLY12AG20 AFHRD 19COMPONENTS,ACCESSORY ACCESSORY COMPONENTS THE ADDITIONAL PARTS SUPPLIED WITH THE ITEM WHICH MAY BE REQUIRED FOR APPLICATION. SELECT REPLY CODE 10AE15 AFHSA 12QUANTITY,COMPONENT,ACCESSORY ACCESSORY COMPONENT QUANTITY THE NUMBER OF PARTS SUPPLIED WITH THE ITEM WHICH MAY BE REQUIRED FOR APPLICATION. 1A MODE REPLY 0 AFHTA /D/ 12QUANTITY,STRAND,LITZ WIRE LITZ WIRE STRAND QUANTITY THE NUMBER OF FINE,SEPARATELY INSULATED STRANDS OF WIRE WOVEN TOGETHER FORMING A SINGLE CONDUCTOR. 1A MODE REPLY 0 AFHUJ /D/A04SIZE,CONDUCTOR,WINDING WINDING CONDUCTOR SIZE THE WIRE GAGE DESIGNATION USED TO DESCRIBE A COIL WIRE OR TRANSFORMER WIRE WINDING SIZE. 1D AND 1A MODE REPLY11AB96 AFHVJ 10WEIGHT,UNIT,UNPACKAGED UNPACKAGED UNIT WEIGHT THE MEASURED WEIGHT OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING MATERIAL. PLEASE USE MRC CTJS IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1B MODE REPLY12AB16 AFHWD 18TYPE,CONNECTION,ELECTRICAL,INTERNAL INTERNAL ELECTRICAL CONNECTION TYPE INDICATES THE TYPE OF INTERNAL ELECTRICAL CONNECTION UTILIZED. SELECT REPLY CODE 10AD01 AFHXD /D/ 09MATERIAL,DIELECTRIC DIELECTRIC MATERIAL THE KIND OF INSULATING MEDIUM USED TO SEPARATE THE CAPACITOR ELECTRODES. SELECT REPLY CODE 10AD09 AFHYG /D/ 19RELATIONSHIP,SECTION TO TERMINAL SECTION TO TERMINAL RELATIONSHIP THE RELATIONSHIP BETWEEN THE INDIVIDUAL SECTIONS OF THE ITEM AND THE CORRESPONDING TERMINAL IDENTIFIERS. FULL TEXT WRITE-IN 0 AFHZB /D/ 04ANGLE IN DEG,POINT,INDEX INDEX POINT ANGLE IN DEG A POINT OF REFERENCE FIXING THE RELATIONSHIP BETWEEN A SPECIFIED SHAFT POSITION AND THE OUTPUT RATIO,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AFJAB /D/ 04ANGLE IN DEG,POINT,PHASING PHASING POINT ANGLE IN DEG A REFERENCE POINT ON A CUP OF A GANG,USUALLY AN OUTPUT RATIO,AN END POINT OR AN INTERMEDIATE TAP,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AFJBB /D/ 10RATIO IN PERCENT,OUTPUT OUTPUT RATIO IN PERCENT THE RATIO OF THE OUTPUT VOLTAGE TO THE DESIGNATED INPUT REFERENCE VOLTAGE,EXPRESSED IN PERCENT. UNLESS OTHERWISE SPECIFIED,THE REFERENCE VOLTAGE IS THE TOTAL APPLIED VOLTAGE. 1B MODE REPLY 0 AFJCD /D/ 07PHASING REQUIRED,CONFORMITY,SIMULTANEOUS SIMULTANEOUS CONFORMITY PHASING REQUIRED AN INDICATION THAT THE RELATIVE ALIGNMENT OF THE CUPS OF A GANG POTENTIOMETER,FROM A COMMON INDEX POINT IS REQUIRED SO THAT THE OUTPUT RATIOS OF ALL CUPS FALL WITHIN THEIR RESPECTIVE CONFORMITY LIMITS OVER THE THEORETICAL ELECTRICAL TRAVEL. SELECT REPLY CODE 10AA89 AFJDA 19CODE,WEAVE WEAVE CODE THE IDENTIFICATION OF A BASIC WEAVE AND/OR ITS SIMPLE VARIATIONS IN ACCORDANCE WITH THE INTERNATIONAL ORGANIZATION FOR STANDARDIZATION (ISO) 9354. 1A MODE REPLY 0 AFJEG 19EQUIPMENT ACCOMMODATED,SPECIFIC SPECIFIC EQUIPMENT ACCOMMODATED THE NAME OF THE EQUIPMENT THE ITEM IS SPECIFICALLY DESIGNED TO ACCOMMODATE. FULL TEXT WRITE-IN 0 AFJFD 19USE,SPECIFIC SPECIFIC USE THE REQUIRED PURPOSE OR APPLICATION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AD34 AFJGB /D/ 10FACTOR,ATTENUATION,TRANSMISSION MEDIUM TRANSMISSION MEDIUM ATTENUATION FACTOR THE RATIO OF THE LIGHT IMPRESSED TO THE LIGHT TRANSMITTED THROUGH A LENS,WHERE THE LIGHT IMPRESSED IS EXPRESSED AS UNITY. 1B MODE REPLY 0 AFJHG 19ITEMS,FURNISHED FURNISHED ITEMS ITEMS FURNISHED AS ACCESSORIES WHICH ARE NOT SPECIFIED ELSEWHERE. FULL TEXT WRITE-IN 0 AFJJD /D/ 18TYPE,STORAGE STORAGE TYPE INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS. PLEASE USE MRC BBRG IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD41 AFJKJ 10MEASURE,CUBIC CUBIC MEASURE A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS. 1D AND 1B MODE REPLY11AD42 AFJLD 07FUMIGATION FUMIGATION AN INDICATION OF WHETHER OR NOT AN ITEM IN STORAGE REQUIRES EXPOSURE TO THE ACTION OF FUMES FOR THE PURPOSE OF DISINFECTION. SELECT REPLY CODE 10AE40 AFJMD /D/ 19FREQUENCY,INSPECTION INSPECTION FREQUENCY THE SPECIFIED TIME INTERVAL NECESSARY TO DETECT MATERIAL DETERIORATION THAT WILL AFFECT STOCK READINESS. SELECT REPLY CODE 10AD38 AFJND 19FACTOR,FRAGILITY FRAGILITY FACTOR THE MEASURE OF SENSITIVITY OF THE ITEM TO BE PACKAGED. A FACTOR USED BY PACKAGING ENGINEERS IN DEVISING PROPER CUSHIONING IN A PACKAGE. SELECT REPLY CODE 10AD40 AFJPD /D/ 19FEATURE,HANDLING,SPECIAL SPECIAL HANDLING FEATURE THAT UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING. SELECT REPLY CODE 10AD43 AFJQJ T10RANGE,TEMP,STORAGE STORAGE TEMP RANGE THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH AN ITEM CAN BE STORED WITHOUT DETRIMENTAL EFFECT. 1D AND 1F MODE REPLY11AB36 AFJRD /D/ 19PLANE,SURFACE,MOUNTING MOUNTING SURFACE PLANE AN INDICATION OF THE SURFACE PLANE ON WHICH AN ITEM IS DESIGNED TO BE MOUNTED. SELECT REPLY CODE 10AC60 AFJSD 11METHOD,PORTABILITY PORTABILITY METHOD THE MEANS,OTHER THAN A CARRYING CASE,PROVIDED FOR MOVEMENT OF THE ITEM. SELECT REPLY CODE 10AD28 AFJTD 19FUNCTION,LIGHT LIGHT FUNCTION THE FUNCTION OF A LIGHT DESIGNED TO INDICATE THE POSITION,MOTION,HAZARDS,AND THE LIKE,OR TO DRAW ATTENTION. SELECT REPLY CODE 10AD72 AFJUD /D/ 07CASE,CARRYING CARRYING CASE AN INDICATION OF WHETHER OR NOT A CONTAINER FROM WHICH THE ITEM IS COMPLETELY REMOVABLE IN NORMAL OPERABLE CONDITION IS PROVIDED. PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB22 AFJVJ 10CAPACITY,CONTAINER,FUEL FUEL CONTAINER CAPACITY THE MAXIMUM QUANTITY OF FUEL THE CONTAINER WILL HOLD. 1D AND 1B MODE REPLY11AD73 AFJWD /D/ 09MATERIAL,RING,BOTTOM BOTTOM RING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BOTTOM RING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AFJXD /D/ 09MATERIAL,RING,INTERMEDIATE INTERMEDIATE RING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INTERMEDIATE RING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AFJYD /D/ 09MATERIAL,RING,TOP TOP RING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TOP RING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AFJZD /D/ 09MATERIAL,RETAINER RETAINER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE RETAINER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AFKAJ /D/ 04LENGTH,PROVISION,WIRING WIRING PROVISION LENGTH THE MEASUREMENT OF EACH WIRING PROVISION OF AN ITEM TAKEN FROM THE BODY TO THE ENDS OF THE WIRING PROVISION,INCLUDING ANY TERMINATIONS. 3D AND 1B MODE REPLY31AA051AC201AE17 AFKBD /D/ 07SPREAD,BEAM,ADJUSTABLE LIGHT ADJUSTABLE LIGHT BEAM SPREAD AN INDICATION OF WHETHER OR NOT THE LIGHT BEAM SPREAD IS ADJUSTABLE. SELECT REPLY CODE 10AA89 AFKCD /D/ 11METHOD,FOCUSING FOCUSING METHOD THE MEANS BY WHICH THE LIGHT RAYS ARE CAUSED TO COME TOGETHER OR SPREAD. SELECT REPLY CODE 10AE18 AFKDD /D/ 05DIRECTION,ADJUSTMENT,LIGHT LIGHT ADJUSTMENT DIRECTION THE DIRECTION IN WHICH THE LIGHT IS ADJUSTABLE. SELECT REPLY CODE 10AC60 AFKED 18TYPE,INCLOSURE,REFLECTOR REFLECTOR INCLOSURE TYPE INDICATES THE TYPE OF INCLOSURE THAT ACCOMMODATES THE REFLECTOR. SELECT REPLY CODE 10AE19 AFKFD /D/ 07TRANSFORMER TRANSFORMER AN INDICATION OF WHETHER OR NOT A TRANSFORMER IS INCLUDED. SELECT REPLY CODE 10AA49 AFKGH /D/ 19DATA,FOOTCANDLE FOOTCANDLE DATA THE INTENSITY OF LIGHT MEASURED AT A GIVEN DISTANCE FROM THE LAMP AND THE FIELD OF LIGHT PROJECTION. 3D MODE REPLY 31AE211AE201AE22 AFKHJ /D/ 10OUTPUT IN MICROWATTS PER SQUARE CENTIMETER,LIGHT LIGHT OUTPUT IN MICROWATTS PER SQUARE CENTIMETER THE AMOUNT OF LIGHT OUTPUT AT A GIVEN DISTANCE FROM THE LIGHT SOURCE,MEASURED IN MICROWATTS PER SQUARE CENTIMETER. 1D AND 1B MODE REPLY11AE23 AFKJB 04ANGLE FROM INLET IN DEG,OPERATING MECHANISM OPERATING MECHANISM ANGLE FROM INLET IN DEG THE ANGLE BETWEEN THE OPERATING MECHANISM AND THE INLET,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AFKKD /D/ 18TYPE,CONTROL,VALVE EXPANSION VALVE EXPANSION CONTROL TYPE INDICATES THE TYPE OF CONTROL BY WHICH THE VALVE IS EXPANDED. SELECT REPLY CODE 10AB09 AFKLD 03DESIGNATION,TEMP RANGE,VALVE EVAPORATOR VALVE EVAPORATOR TEMP RANGE DESIGNATION A DESIGNATION OF THE EVAPORATOR TEMPERATURE RANGE AT WHICH THE VALVE IS DESIGNED TO OPERATE. SELECT REPLY CODE 10AE25 AFKMD /D/ 07DEVICE,LIMITING,VALVE PRESSURE VALVE PRESSURE LIMITING DEVICE AN INDICATION OF WHETHER OR NOT A DEVICE IS INCLUDED THAT THROTTLES OR STOPS THE FLOW OF LIQUID,GAS,AND THE LIKE,THROUGH THE VALVE WHEN EVAPORATOR SUCTION PRESSURE REACHES THE MAXIMUM PRESSURE SETTING. SELECT REPLY CODE 10AA49 AFKNJ 10SETTING,DEVICE,LIMITING,VALVE PRESSURE VALVE PRESSURE LIMITING DEVICE SETTING THE SETTING AT WHICH THE VALVE PRESSURE LIMITING DEVICE IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY11AB18 AFKPJ T10RANGE,DEVICE,LIMITING,VALVE PRESSURE VALVE PRESSURE LIMITING DEVICE RANGE THE MINIMUM TO MAXIMUM LIMITS IN WHICH THE VALVE PRESSURE LIMITING DEVICE IS DESIGNED TO OPERATE. 1D AND 1F MODE REPLY11AB18 AFKQD /D/ 18TYPE,MEDIA,BULB BULB MEDIA TYPE INDICATES THE TYPE OF TRANSFER AGENT CONTAINED IN THE THERMOSTATIC BULB WHICH REACTS TO TEMPERATURE CHANGE. SELECT REPLY CODE 10AB75 AFKRD /D/ 11METHOD,MOUNTING,BULB BULB MOUNTING METHOD THE MEANS UTILIZED TO HOLD THE BULB IN POSITION. SELECT REPLY CODE 10AB89 AFKSD 03DESIGNATION,SIZE,COMMERCIAL BATTERY COMMERCIAL BATTERY SIZE DESIGNATION THE COMMERCIAL DESIGNATION OF THE BATTERY SIZE. SELECT REPLY CODE 10AD57 AFKTD 09MATERIAL,CONDUIT,FLEXIBLE FLEXIBLE CONDUIT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FLEXIBLE CONDUIT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10MA01 AFKUD /D/ 08LOCATION,EQUALIZER,VALVE VALVE EQUALIZER LOCATION INDICATES WHETHER THE EQUALIZER LOCATION IS INTERNAL,EXTERNAL,OR BOTH. SELECT REPLY CODE 10AE46 AFKVD 18TYPE,CONNECTION,VALVE EQUALIZER VALVE EQUALIZER CONNECTION TYPE INDICATES THE TYPE OF CONNECTION IN THE VALVE BODY FOR CONNECTING THE EQUALIZER LINE. SELECT REPLY CODE 10AA84 AFKWJ 04DIAMETER,CONNECTION,VALVE EQUALIZER VALVE EQUALIZER CONNECTION DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE VALVE EQUALIZER CONNECTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AFKXD /D/ 18TYPE,DEVICE,CONTROL,TEMP TEMP CONTROL DEVICE TYPE INDICATES THE TYPE OF TEMPERATURE CONTROL DEVICE THAT ACTUATES THE ITEM. SELECT REPLY CODE 10AB09 AFKYD 19SYSTEM FOR WHICH DESIGNED,SPRINKLER SPRINKLER SYSTEM FOR WHICH DESIGNED INDICATES THE TYPE OF SPRINKLER SYSTEM IN WHICH THE ITEM IS DESIGNED TO BE USED. SELECT REPLY CODE 10AE26 AFKZD 18TYPE FOR WHICH DESIGNED,TANK TANK TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF TANK FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AE25 AFLAD /D/ 19PROTECTION,ENVIRONMENTAL,CORE CORE ENVIRONMENTAL PROTECTION THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT THE CORE IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY. SELECT REPLY CODE 10AA65 AFLBD 03DESIGNATOR,COMMERCIAL,CORE LENGTH COMMERCIAL CORE LENGTH DESIGNATOR THE COMMERCIAL DESIGNATION OF THE CORE LENGTH. SELECT REPLY CODE 10AB79 AFLCD /D/ 09MATERIAL,SPRING SPRING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SPRING IS FABRICATED. SELECT REPLY CODE 10AD09 AFLDD 10TENSION RATING,SPRING,COMMERCIAL COMMERCIAL SPRING TENSION RATING A COMMERCIAL RATING OF THE PRESSURE REQUIRED TO COMPRESS THE SPRING. SELECT REPLY CODE 10AE25 AFLED 18TYPE,DESIGN,VALVE VENTING VALVE VENTING DESIGN TYPE INDICATES THE TYPE OF VALVE VENTING DESIGN,WHETHER FOR USE IN A CLOSED SYSTEM OR FOR VENTING TO THE ATMOSPHERE. SELECT REPLY CODE 10AE29 AFLFD 18TYPE,DESIGN,VALVE RELIEF VALVE RELIEF DESIGN TYPE INDICATES THE TYPE OF VALVE RELIEF DESIGN,WHETHER FOR PRESSURE OR VACUUM RELIEF OR FOR BOTH PRESSURE AND VACUUM RELIEF. SELECT REPLY CODE 10AE30 AFLGB 10SETTING,PRESSURE,ABSOLUTE ABSOLUTE PRESSURE SETTING THE PRESSURE ABSOLUTE /VACUUM/ AT WHICH THE ITEM IS SET TO OPEN. 1B MODE REPLY 0 AFLHF T10RANGE,PRESSURE,ABSOLUTE ABSOLUTE PRESSURE RANGE THE MINIMUM TO MAXIMUM PRESSURES ABSOLUTE /VACUUM/ AT WHICH THE ITEM MAY BE SET TO OPEN. 1F MODE REPLY 0 AFLJD /D/ 07APPLICATION,UNDERWATER UNDERWATER APPLICATION AN INDICATION OF WHETHER OR NOT THE ITEM IS SUITABLE FOR UNDERWATER USE. SELECT REPLY CODE 10AA89 AFLKD /D/ 08LOCATION,SPRING,VALVE LOADING VALVE LOADING SPRING LOCATION INDICATES THE LOCATION OF THE VALVE LOADING SPRING AS RELATED TO THE VALVE BODY. SELECT REPLY CODE 10AE46 AFLLD /D/ 08LOCATION,SEAT,VALVE VALVE SEAT LOCATION INDICATES THE LOCATION OF THE VALVE SEAT AS RELATED TO THE VALVE BODY. SELECT REPLY CODE 10AE46 AFLMD /D/ 18TYPE,FLUSH FLUSH TYPE INDICATES THE DESIGN FEATURE OF THE ITEM THAT CONTROLS THE FLOW. SELECT REPLY CODE 10AE31 AFLNJ 04DISTANCE BETWEEN HOLES ALONG LENGTH,CENTER TO CENTER,FIRST END FIRST END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFLPJ 04DISTANCE BETWEEN HOLES ALONG LENGTH,CENTER TO CENTER,SECOND END SECOND END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFLQJ 04DISTANCE BETWEEN HOLES ALONG LENGTH,CENTER TO CENTER,THIRD END THIRD END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFLRJ 04DISTANCE BETWEEN HOLES ALONG LENGTH,CENTER TO CENTER,FOURTH END FOURTH END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFLSJ 04DISTANCE BETWEEN HOLES ALONG WIDTH,CENTER TO CENTER,FIRST END FIRST END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFLTJ 04DISTANCE BETWEEN HOLES ALONG WIDTH,CENTER TO CENTER,SECOND END SECOND END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFLUJ 04DISTANCE BETWEEN HOLES ALONG WIDTH,CENTER TO CENTER,THIRD END THIRD END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFLVJ 04DISTANCE BETWEEN HOLES ALONG WIDTH,CENTER TO CENTER,FOURTH END FOURTH END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFLWD 11METHOD,ACTUATION ACTUATION METHOD THE MEANS BY WHICH THE ITEM IS ACTUATED. SELECT REPLY CODE 10AC58 AFLXD /D/ 11METHOD,DEACTUATION DEACTUATION METHOD THE MEANS BY WHICH AN ITEM IS DEACTUATED. SELECT REPLY CODE 10AC58 AFLYD /D/ 11METHOD,SIGNAL,FUNCTIONING FUNCTIONING SIGNAL METHOD THE MEANS /AUDIBLE,VISUAL,AND THE LIKE/ USED TO SIGNIFY THAT THE ITEM IS FUNCTIONING. SELECT REPLY CODE 10AD51 AFLZD /D/ 07ACCOMMODATION,BATTERY,INTERNAL INTERNAL BATTERY ACCOMMODATION AN INDICATION OF WHETHER OR NOT A FACILITY/IES/ TO ACCOMMODATE A BATTERY/IES/ IS INCLUDED. SELECT REPLY CODE 10AA89 AFMAD /D/ 18TYPE,SIGNAL SIGNAL TYPE INDICATES THE TYPE OF SIGNALLING FUNCTION THE ITEM WILL PERFORM. SELECT REPLY CODE 10AE27 AFMBD /D/ 07FLASHER UNIT FLASHER UNIT AN INDICATION OF WHETHER OR NOT A FLASHER UNIT IS INCLUDED. SELECT REPLY CODE 10AA89 AFMCD 18TYPE,ACCOMMODATION,FLASHER UNIT FLASHER UNIT ACCOMMODATION TYPE INDICATES THE TYPE OF ACCOMMODATION INCLUDED FOR THE FLASHER UNIT. SELECT REPLY CODE 10AD15 AFMDD /D/ 19ARRANGEMENT,CONTACT,CONTROL CONTROL CONTACT ARRANGEMENT A DESIGNATION THAT DESCRIBES THE BASIC ELECTRICAL CONFIGURATION OF A CONTROL CONTACT ARRANGEMENT BY WHICH AN ELECTRICAL CIRCUIT IS COMPLETED OR INTERRUPTED. SELECT REPLY CODE 10AC98 AFMED /D/ 07WIRING PROVISION WIRING PROVISION AN INDICATION OF WHETHER OR NOT WIRING PROVISIONS ARE INCLUDED FOR CONNECTING THE ITEM ELECTRICALLY TO ANOTHER ITEM OR TO THE NEXT HIGHER ASSEMBLY. SELECT REPLY CODE 10AA89 AFMFD /D/ 07ACTUATION CONTROL,ADJUSTABLE LIGHT INTENSITY ADJUSTABLE LIGHT INTENSITY ACTUATION CONTROL AN INDICATION OF WHETHER OR NOT THE LEVEL OF ACTUATION OF THE LIGHT INTENSITY ACTUATION CONTROL IS ADJUSTABLE. SELECT REPLY CODE 10AA89 AFMGJ /D/ 10ACTUATION SETTING,LIGHT INTENSITY LIGHT INTENSITY ACTUATION SETTING THE PREDETERMINED LIGHT INTENSITY /UNITS OF ILLUMINATION/ AT WHICH THE ITEM IS DESIGNED TO ACTUATE. 1D AND 1B MODE REPLY11AE28 AFMHJ /D/ 10DEACTUATION SETTING,LIGHT INTENSITY LIGHT INTENSITY DEACTUATION SETTING THE PREDETERMINED LIGHT INTENSITY /UNIT/S/ OF ILLUMINATION/ AT WHICH THE ITEM IS DESIGNED TO DEACTUATE. 1D AND 1B MODE REPLY11AE28 AFMJJ /D/T10ACTUATION RANGE,LIGHT INTENSITY LIGHT INTENSITY ACTUATION RANGE THE PREDETERMINED RANGE OF LIGHT INTENSITY /UNIT/S/ OF ILLUMINATION/ AT WHICH THE ITEM IS DESIGNED TO ACTUATE. 1D AND 1F MODE REPLY11AE28 AFMKJ /D/T10DEACTUATION RANGE,LIGHT INTENSITY LIGHT INTENSITY DEACTUATION RANGE THE PREDETERMINED RANGE OF LIGHT INTENSITY /UNIT/S/ OF ILLUMINATION/ AT WHICH THE ITEM IS DESIGNED TO DEACTUATE. 1D AND 1F MODE REPLY11AE28 AFMLD /D/ 18TYPE,DEVICE,ROTATION CONTROL ROTATION CONTROL DEVICE TYPE INDICATES THE TYPE OF DEVICE USED IN THE ITEM TO EFFECT ROTATION OF THE CONTROLLED ITEM. SELECT REPLY CODE 10AE34 AFMMD /D/ 05DIRECTION,ROTATION,AZIMUTHAL AZIMUTHAL ROTATION DIRECTION THE DIRECTION OF ROTATION OF THE CONTROLLED ITEM IN THE HORIZONTAL PLANE,ESTABLISHED BY THE DESIGN OF THE CONTROL. SELECT REPLY CODE 10AE32 AFMNB /D/ 10ROTATION IN DEG,AZIMUTH,MAXIMUM MAXIMUM AZIMUTH ROTATION IN DEG THE LIMIT OF THE ROTATION OF THE CONTROLLED ITEM IN THE HORIZONTAL PLANE,ESTABLISHED BY THE DESIGN OF THE CONTROL,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AFMPF /D/T10TILT LIMITS FROM THE HORIZONTAL PLANE IN DEG,VERTICAL VERTICAL TILT LIMITS FROM THE HORIZONTAL PLANE IN DEG THE VERTICAL TILT LIMITS FROM THE HORIZONTAL PLANE,ESTABLISHED BY DESIGN OF THE CONTROL,EXPRESSED IN DEGREES. 1F MODE REPLY 0 AFMQJ 04HEIGHT,INSIDE INSIDE HEIGHT AN INSIDE MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN ITEM,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AFMRJ 04DEPTH,COVER COVER DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFMSJ 04LENGTH,FLAP,DUST DUST FLAP LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFMTJ 04LENGTH,TUCK TUCK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFMUJ 04LENGTH,FLAP,INNER INNER FLAP LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFMVJ 04WIDTH ACROSS FLATS,INSIDE INSIDE WIDTH ACROSS FLATS A MEASUREMENT OF THE INSIDE DISTANCE FROM ONE FLAT TO THE OPPOSITE FLAT. 2D AND 1B MODE REPLY21AA051AC20 AFMWJ 04HEIGHT,OUTSIDE OUTSIDE HEIGHT AN OUTSIDE MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN ITEM,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AFMXJ 04LENGTH,INSIDE,TOP TOP INSIDE LENGTH AN INSIDE MEASUREMENT OF THE LONGEST DIMENSION OF THE TOP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AFMYJ 04WIDTH,INSIDE,TOP TOP INSIDE WIDTH AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TOP,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AFMZJ 04LENGTH,INSIDE,BOTTOM BOTTOM INSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNAJ 04WIDTH,INSIDE,BOTTOM BOTTOM INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNBJ 04LENGTH,OUTSIDE,FIRST BOX FIRST BOX OUTSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNCJ 04WIDTH,OUTSIDE,FIRST BOX FIRST BOX OUTSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNDJ 04HEIGHT,OUTSIDE,FIRST BOX FIRST BOX OUTSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNEJ /D/ 04DIAMETER,OUTSIDE,FIRST BOX FIRST BOX OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNFJ 04LENGTH,OVERALL,FIRST BOX FIRST BOX OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNGJ 04WIDTH,OVERALL,FIRST BOX FIRST BOX OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNHJ 04HEIGHT,OVERALL,FIRST BOX FIRST BOX OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNJJ 04LENGTH,OUTSIDE,SECOND BOX SECOND BOX OUTSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNKJ 04WIDTH,OUTSIDE,SECOND BOX SECOND BOX OUTSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNLJ 04HEIGHT,OUTSIDE,SECOND BOX SECOND BOX OUTSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNMJ /D/ 04DIAMETER,OUTSIDE,SECOND BOX SECOND BOX OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNNJ 04LENGTH,OVERALL,SECOND BOX SECOND BOX OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNPJ 04WIDTH,OVERALL,SECOND BOX SECOND BOX OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNQJ 04HEIGHT,OVERALL,SECOND BOX SECOND BOX OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNRJ 04LENGTH,OUTSIDE,THIRD BOX THIRD BOX OUTSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNSJ 04WIDTH,OUTSIDE,THIRD BOX THIRD BOX OUTSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNTJ 04HEIGHT,OUTSIDE,THIRD BOX THIRD BOX OUTSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNUJ /D/ 04DIAMETER,OUTSIDE,THIRD BOX THIRD BOX OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNVJ 04LENGTH,OVERALL,THIRD BOX THIRD BOX OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNWJ 04WIDTH,OVERALL,THIRD BOX THIRD BOX OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNXJ 04HEIGHT,OVERALL,THIRD BOX THIRD BOX OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNYJ /D/ 04LENGTH,OUTSIDE,FOURTH BOX FOURTH BOX OUTSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFNZJ /D/ 04WIDTH,OUTSIDE,FOURTH BOX FOURTH BOX OUTSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFPAJ /D/ 04HEIGHT,OUTSIDE,FOURTH BOX FOURTH BOX OUTSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AFPBJ /D/ 04DIAMETER,OUTSIDE,FOURTH BOX FOURTH BOX OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFPCJ /D/ 04LENGTH,OVERALL,FOURTH BOX FOURTH BOX OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFPDJ /D/ 04WIDTH,OVERALL,FOURTH BOX FOURTH BOX OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFPEJ 04HEIGHT,OVERALL,FOURTH BOX FOURTH BOX OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AFPFJ /D/ 04DISTANCE BETWEEN MOUNTING HOLES ALONG LENGTH,CENTER TO CENTER,FIRST FIRST CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFPGJ /D/ 04DISTANCE BETWEEN MOUNTING HOLES ALONG LENGTH,CENTER TO CENTER,SECOND SECOND CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFPHJ 10STRENGTH,BURSTING,MATERIAL MATERIAL BURSTING STRENGTH THE MINIMUM FORCE REQUIRED TO RUPTURE THE MATERIAL,EXPRESSED IN SPECIFIED UNITS OF MEASURE PER UNIT OF AREA. 1D AND 1B MODE REPLY11AB18 AFPJD /D/ 09MATERIAL,COVERING,EXTERIOR EXTERIOR COVERING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE EXTERIOR COVERING IS FABRICATED. SELECT REPLY CODE 10AD09 AFPKD /D/ 09MATERIAL,COVERING,INTERIOR INTERIOR COVERING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INTERIOR COVERING IS FABRICATED. SELECT REPLY CODE 10AD09 AFPLD 01COLOR,INTERIOR INTERIOR COLOR THE HUE OR TINT OF THE INTERIOR OF THE ITEM. SELECT REPLY CODE 10AD06 AFPMD /D/ 19FORM,ASSEMBLY ASSEMBLY FORM THE FORM OF ASSEMBLY IN WHICH THE ITEM IS SUPPLIED,WHETHER COMPLETELY ASSEMBLED OR SPECIFYING A DEGREE OF ASSEMBLY WHICH INHERENTLY DESCRIBES THE PRESENCE OF A SPACE SAVING FEATURE. SELECT REPLY CODE 10AE33 AFPND 11METHOD,ASSEMBLY ASSEMBLY METHOD THE MEANS BY WHICH THE BODY PARTS ARE DESIGNED TO BE FASTENED TOGETHER. SELECT REPLY CODE 10AB47 AFPPD 11METHOD,CLOSURE CLOSURE METHOD THE MEANS PROVIDED TO CLOSE THE OPENING OF THE ITEM. SELECT REPLY CODE 10AE35 AFPQD 18TYPE,FASTENING,CLOSURE CLOSURE FASTENING TYPE INDICATES THE TYPE OF DEVICE(S) USED TO SECURE THE CLOSURE OF THE ITEM. SELECT REPLY CODE 10AE36 AFPRD 11METHOD,FACILITY,LOADING LOADING FACILITY METHOD THE MEANS PROVIDED TO FACILITATE LOADING AND UNLOADING THE ITEM. SELECT REPLY CODE 10AE35 AFPSB 10RATIO,EFFICIENCY,ENERGY ENERGY EFFICIENCY RATIO A RATING COMPUTED BY DIVIDING COOLING CAPACITY (BTUS)BY THE WATTS OF POWER USED TO HELP DETERMINE THE OPERATING COST. 1B MODE REPLY 0 AFPTJ 04LENGTH,COMPARTMENT COMPARTMENT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A COMPARTMENT,AT THE OPENING,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AFPUJ 04WIDTH,COMPARTMENT COMPARTMENT WIDTH A MEASUREMENT OF THE SHORTEST DIMENSION OF A COMPARTMENT,AT THE OPENING,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AFPVA 12QUANTITY,COMPARTMENT COMPARTMENT QUANTITY THE NUMBER OF COMPARTMENTS FORMED BY PARTITIONS. 1A MODE REPLY 0 AFPWD 11METHOD,REINFORCEMENT REINFORCEMENT METHOD THE MEANS PROVIDED TO ADD STRENGTH AND/OR PROTECTION TO THE ITEM. SELECT REPLY CODE 10AE37 AFPXD /D/ 07FEATURE,DESIGN,HUMIDITY CONTROL HUMIDITY CONTROL DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A DESIGN FEATURE IS PROVIDED FOR CONTROLLING THE HUMIDITY WITHIN THE ITEM. SELECT REPLY CODE 10AA89 AFPYJ 10CAPACITY,CUBIC CUBIC CAPACITY A MEASUREMENT OF THE INTERNAL CAPACITY OF AN ITEM TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE DEPTH AND RENDERED IN CUBIC UNITS. 1D AND 1B MODE REPLY11AD42 AFPZD 03DESIGNATION,HAZARD,CONTAINER LOAD CONTAINER LOAD HAZARD DESIGNATION A DESIGNATION OF THE MOST DIFFICULT TYPE OF LOAD FOR WHICH A CONTAINER IS DESIGNED WITH RESPECT TO THE HAZARDS IMPOSED BY THE ACTIONS OF INTERNAL AND EXTERNAL FORCES. SELECT REPLY CODE 10AE38 AFQAD /D/ 07FEATURE,STACKING STACKING FEATURE AN INDICATION OF WHETHER OR NOT A DESIGN FEATURE IS EMPLOYED THAT PROVIDES FOR SAFE AND LEVEL STACKING OF ONE ITEM UPON ANOTHER. SELECT REPLY CODE 10AA89 AFQBD /D/ 07FEATURE,NESTING NESTING FEATURE AN INDICATION OF WHETHER OR NOT A DESIGN FEATURE IS EMPLOYED,SUCH AS SLOPING SIDEWALLS,WHICH PERMITS THE NESTING OF ITEMS TO CONSERVE SPACE. SELECT REPLY CODE 10AA89 AFQCA 12QUANTITY PER SET,ITEMS,MATCHED MATCHED ITEMS QUANTITY PER SET THE NUMBER OF MATCHED ITEMS REQUIRED TO COMPLETE A SET. 1A MODE REPLY 0 AFQDD /D/ 19POSITION,TAPE TAPE POSITION THE POSITION OF THE TAPE WHEN INSTALLED IN THE INSTRUMENT. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. SELECT REPLY CODE 10AA38 AFQEA 12QUANTITY,COMPARTMENT,COIN COIN COMPARTMENT QUANTITY THE NUMBER OF COMPARTMENTS DESIGNED TO ACCOMMODATE COINS. 1A MODE REPLY 0 AFQFA 12QUANTITY,COMPARTMENT,CURRENCY CURRENCY COMPARTMENT QUANTITY THE NUMBER OF COMPARTMENTS DESIGNED TO ACCOMMODATE CURRENCY. 1A MODE REPLY 0 AFQGD 19CERTIFICATE,MANUFACTURER,BOX BOX MANUFACTURER CERTIFICATE THE CERTIFICATE REQUIRED ON FIBERBOARD SHIPPING CONTAINERS SHOWING THE NAME AND ADDRESS OF THE MANUFACTURER,TOGETHER WITH CERTIFICATION DATA THAT THE CONTAINER HAS BEEN MANUFACTURED AND TESTED IN ACCORDANCE WITH THE REGULATIONS OF THE COMMON CARRIER THAT GOVERNS THE SHIPMENT. SELECT REPLY CODE 10AE40 AFQHJ /D/ 04RADIUS,LOBE LOBE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AFQJJ 04DIAMETER,ENTRANCE,CABLE CABLE ENTRANCE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CABLE ENTRANCE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AFQKJ 04DISTANCE FROM MOUNTING SHOULDER TO FRONT FACE DISTANCE FROM MOUNTING SHOULDER TO FRONT FACE NONE. 2D AND 1B MODE REPLY21AA051AC20 AFQLJ 04DISTANCE FROM MOUNTING SHOULDER TO REAR FACE DISTANCE FROM MOUNTING SHOULDER TO REAR FACE NONE. 2D AND 1B MODE REPLY21AA051AC20 AFQMJ 04DISTANCE BETWEEN MOUNTING HOLE CENTERS DISTANCE BETWEEN MOUNTING HOLE CENTERS THE DISTANCE BETWEEN THE CENTERLINE OF THE MOUNTING HOLES. 2D AND 1B MODE REPLY21AA051AC20 AFQNJ 04LENGTH,FLANGE FLANGE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A FLANGE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AFQPJ 04LENGTH,ACCOMMODATED,BOARD BOARD ACCOMMODATED LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFQQJ 04THICKNESS,FACILITY,MOUNTING MOUNTING FACILITY THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AFQRD 18TYPE,DEVICE,THREADED THREADED DEVICE TYPE INDICATES THE TYPE OF THREADED DEVICE INCLUDED ON THE ITEM. SELECT REPLY CODE 10AE49 AFQUD 18TYPE,COMPUTER SYSTEM COMPUTER SYSTEM TYPE INDICATES THE TYPE OF COMPUTER SYSTEM WITH WHICH THE ITEM WILL COMMUNICATE. SELECT REPLY CODE 10AA01 AFQVJ 04WIDTH,ACCOMMODATED,BOARD BOARD ACCOMMODATED WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFQWA 12QUANTITY,END,MATING MATING END QUANTITY THE NUMBER OF MATING ENDS PROVIDED WITH THE ITEM WHICH ARE DESIGNED TO ACCOMMODATE ANOTHER CONNECTOR. 1A MODE REPLY 0 AFQXL 16STYLE,ARRANGEMENT,CONTACT POSITION CONTACT POSITION ARRANGEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE CONTACT POSITION/S/. 1L MODE REPLY 0 AFQYD /D/ 07CONTACT INCLUSION CONTACT INCLUSION AN INDICATION OF WHETHER OR NOT A CONTACT/S/ IS INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA89 AFQZD 07REMOVABILITY,CONTACT CONTACT REMOVABILITY AN INDICATION OF WHETHER OR NOT THE CONTACT(S) IS REMOVABLE. SELECT REPLY CODE 10AC29 AFRAA 12QUANTITY,CONTACT CONTACT QUANTITY THE NUMBER OF CONTACTS WHICH PROVIDE ELECTRICAL CONNECTION. 1A MODE REPLY 0 AFRBL 16STYLE,CONTACT CONTACT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CONTACT. 1L MODE REPLY 0 AFRCB 10CURRENT RATING IN AMPS,MAXIMUM,CONTACT CONTACT MAXIMUM CURRENT RATING IN AMPS THE MAXIMUM CURRENT WHICH THE CONTACT MAY CONTINUOUSLY CARRY WITHOUT DEGRADATION OR DESTRUCTION,EXPRESSED IN AMPERES. 1B MODE REPLY 0 AFRDB 10VOLTAGE RATING IN VOLTS,AC,MAXIMUM,CONTACT CONTACT MAXIMUM AC VOLTAGE RATING IN VOLTS THE MAXIMUM ALTERNATING CURRENT POTENTIAL THAT MAY BE APPLIED CONTINUOUSLY TO THE CONTACT WITHOUT DAMAGE,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AFREB 10VOLTAGE RATING IN VOLTS,DC,MAXIMUM,CONTACT CONTACT MAXIMUM DC VOLTAGE RATING IN VOLTS THE MAXIMUM DIRECT CURRENT POTENTIAL THAT MAY BE APPLIED CONTINUOUSLY TO THE CONTACT WITHOUT DAMAGE,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AFRFJ 10FREQUENCY RATING,MAXIMUM,CONTACT CONTACT MAXIMUM FREQUENCY RATING THE MAXIMUM FREQUENCY AT WHICH THE CONTACT IS RATED. 1D AND 1B MODE REPLY11AC32 AFRGD /D/ 09MATERIAL,CONTACT CONTACT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CONTACT/S/ IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC CQTZ IN PLACE OF THIS DISCONTINUEDMRC. SELECT REPLY CODE 10AD09 AFRHD /D/ 17SURFACE TREATMENT,CONTACT CONTACT SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE CONTACT SURFACE. SELECT REPLY CODE 10AD09 AFRJA /D/ 19POSITION,CONTACT,THERMOCOUPLE THERMOCOUPLE CONTACT POSITION A DESIGNATION WHICH SERVES TO IDENTIFY THE POSITION OF THE THERMOCOUPLE CONTACT/S/. 1A MODE REPLY 0 AFRKA /D/ 16STYLE,CONTACT,ACCOMMODATED ACCOMMODATED CONTACT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CONTACT/S/ ACCOMMODATED BY THE ITEM. 1A MODE REPLY 0 AFRLA 12QUANTITY,CONTACT,ACCOMMODATED ACCOMMODATED CONTACT QUANTITY THE NUMBER OF CONTACTS ACCOMMODATED BY THE ITEM. 1A MODE REPLY 0 AFRMD /D/ 07CONTACT INCLUSION,ACCOMMODATED ACCOMMODATED CONTACT INCLUSION AN INDICATION OF WHETHER OR NOT THE CONTACT/S/ WHICH AN ITEM IS DESIGNED TO ACCOMMODATE IS INCLUDED. SELECT REPLY CODE 10AA89 AFRND 11METHOD,POLARIZATION POLARIZATION METHOD THE MEANS USED TO PREVENT MISMATING OR CROSS PLUGGING OF CONTACTS. SELECT REPLY CODE 10AE41 AFRPB 10POSITION IN DEG,INSERT INSERT POSITION IN DEG THE AMOUNT OF CLOCKWISE DISPLACEMENT OF THE INDEXING RADIUS OF THE INSERT FROM NORMAL POSITION,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AFRQD /D/ 09MATERIAL,INSERT INSERT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INSERT IS FABRICATED. SELECT REPLY CODE 10AD09 AFRRD 19FRAGRANCE FRAGRANCE A SWEET OR PLEASANT ODOR, SCENT. SELECT REPLY CODE 10AC09 AFRSD 11METHOD,INCLOSURE,INSERT INSERT INCLOSURE METHOD THE MEANS PROVIDED TO COAT,COVER,PROTECT,OR ENCASE THE INSERT. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. SELECT REPLY CODE 10AG85 AFRTD 18TYPE,SHELL SHELL TYPE INDICATES THE TYPE OF SHELL INCLUDED ON THE ITEM. SELECT REPLY CODE 10AE48 AFRUD /D/ 17SURFACE TREATMENT,SHELL SHELL SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SHELL SURFACE. PLEASE USE MRC SFTT WITH ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AFRVD 11METHOD,LOCKING,CONNECTOR CONNECTOR LOCKING METHOD THE MEANS USED TO SECURE A CONNECTOR TO ITS MATING COUNTERPART. SELECT REPLY CODE 10AE44 AFRWD 11METHOD,RELIEF,CONNECTOR CABLE STRAIN CONNECTOR CABLE STRAIN RELIEF METHOD THE MEANS BY WHICH THE CONNECTOR CABLE IS RELIEVED OF STRESS AND STRAIN. SELECT REPLY CODE 10AE45 AFRXD /D/ 14SHAPE,HOLE,BUSHING ACCOMMODATION BUSHING ACCOMMODATION HOLE SHAPE THE PHYSICAL CONFIGURATION OF THE HOLE DESIGNED TO ACCOMMODATE A BUSHING. SELECT REPLY CODE 10AD07 AFRYB 10IMPEDANCE IN OHMS,CHARACTERISTIC,RADIO FREQUENCY TYPE CONTACT RADIO FREQUENCY TYPE CONTACT CHARACTERISTIC IMPEDANCE IN OHMS THE IMPEDANCE FOR WHICH THE ITEM IS DESIGNED FOR MAXIMUM POWER TRANSFER,EXPRESSED IN OHMS. 1B MODE REPLY 0 AFRZD /D/ 19CONNECTION,GROUNDING,CONTACT CONTACT GROUNDING CONNECTION INDICATES THE GROUNDING CONNECTION OF THE CONTACT. SELECT REPLY CODE 10AE47 AFSAL 16STYLE,CARTRIDGE CARTRIDGE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CARTRIDGE. 1L MODE REPLY 0 AFSBL 16STYLE,FLASHTUBE FLASHTUBE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FLASHTUBE. 1L MODE REPLY 0 AFSCJ 04LENGTH,LEAD,WIRE WIRE LEAD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A WIRE LEAD. 2D AND 1B MODE REPLY21AA051AC20 AFSDJ 04LENGTH,OVERALL,CARTRIDGE CARTRIDGE OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFSEJ 04DIAMETER,OVERALL,CARTRIDGE CARTRIDGE OVERALL DIAMETER THE OVERALL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CARTRIDGE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AFSFJ 04LENGTH,OVERALL,FLASHTUBE FLASHTUBE OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFSGJ /D/ 10WAVELENGTH RATING IN ANGSTROMS,LIGHT LIGHT WAVELENGTH RATING IN ANGSTROMS THE VALUE OF THE LIGHT WAVELENGTH FOR WHICH THE ITEM IS RATED,EXPRESSED IN ANGSTROMS. 1D AND 1B MODE REPLY11AC20 AFSHD 18TYPE,LAMP,PRIMARY PRIMARY LAMP TYPE INDICATES THE TYPE OF LAMP WHICH IS AN INTEGRAL PART OF THE LAMP CARTRIDGE. SELECT REPLY CODE 10AD48 AFSJD /D/ 18TYPE,GAS,LAMP LAMP GAS TYPE INDICATES THE TYPE OF GAS WITH WHICH THE LAMP IS FILLED. SELECT REPLY CODE 10AE50 AFSKJ /D/ 10VOLTAGE RATING IN VOLTS,GAS STRIKING,LAMP,AC AC LAMP GAS STRIKING VOLTAGE RATING IN VOLTS THE RATED ALTERNATING CURRENT ELECTROMOTIVE FORCE WHICH WILL CAUSE THE GAS WITHIN THE LAMP TO IONIZE AND BECOME ELECTRICALLY CHARGED,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 AFSLJ /D/ 10VOLTAGE RATING IN VOLTS,GAS STRIKING,LAMP,DC DC LAMP GAS STRIKING VOLTAGE RATING IN VOLTS THE RATED DIRECT CURRENT ELECTROMOTIVE FORCE WHICH WILL CAUSE THE GAS WITHIN THE LAMP TO IONIZE AND BECOME ELECTRICALLY CHARGED,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 AFSMD 19LEVEL,INTENSITY,LIGHT LIGHT INTENSITY LEVEL THE LEVEL OF BRIGHTNESS OF THE LIGHT FLUX PRODUCED BY THE ITEM. SELECT REPLY CODE 10AE25 AFSND /D/ 09MATERIAL,FILAMENT FILAMENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FILAMENT/S/ IS FABRICATED. SELECT REPLY CODE 10AD09 AFSPA 03DESIGNATION,FILAMENT FILAMENT DESIGNATION A DESIGNATION OF THE FORM OF THE FILAMENT WIRE OR RIBBON AND THE ARRANGEMENT ON THE SUPPORTS. 1A MODE REPLY 0 AFSQJ 10VOLTAGE RATING IN VOLTS,CIRCUIT CIRCUIT VOLTAGE RATING IN VOLTS THE TOTAL ELECTRICAL VOLTAGE OF THE CIRCUIT IN WHICH THE ITEM IS DESIGNED TO BE USED,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 AFSRB /D/ 10VOLTAGE RATING IN VOLTS,DESIGN,LAMP LAMP DESIGN VOLTAGE RATING IN VOLTS THE ELECTRICAL VOLTAGE FOR WHICH THE LAMP IS DESIGNED FOR RATED AMPERE,CANDLEPOWER,AND LABORATORY-LIFE CHARACTERISTICS,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AFSSJ 10CURRENT RATING IN AMPS,DESIGN DESIGN CURRENT RATING IN AMPS THE VALUE OF THE CURRENT FLOWING THROUGH THE ITEM WHEN OPERATED AT ITS DESIGNED VOLTAGE,EXPRESSED IN AMPERES. 1D AND 1B MODE REPLY11AC20 AFSTJ 10OUTPUT RATING,LIGHT LIGHT OUTPUT RATING THE VALUE OF OUTPUT BRIGHTNESS FOR WHICH AN ITEM IS RATED. 2D AND 1B MODE REPLY21AE511AC20 AFSUD 19MEASUREMENT,LIFE,AVERAGE AVERAGE LIFE MEASUREMENT A TERM USED TO DENOTE THE SPECIFIC MEASUREMENT OF DURATION USED TO INDICATE THE AVERAGE LIFE OF THE ITEM. SELECT REPLY CODE 10AE52 AFSVB 10LIFE RATING IN HOURS,AVERAGE AVERAGE LIFE RATING IN HOURS THE NUMERIC VALUE INDICATING THE AVERAGE LIFE EXPECTANCY FOR WHICH THE ITEM IS RATED,EXPRESSED IN HOURS. 1B MODE REPLY 0 AFSWD /D/ 19POSITION,BURNING,LAMP LAMP BURNING POSITION THE PHYSICAL POSITION IN WHICH THE LAMP IS DESIGNED TO OPERATE. SELECT REPLY CODE 10AE53 AFSXD 19SERVICE RATING,DUTY,HEAVY,FILAMENT FILAMENT HEAVY DUTY SERVICE RATING AN INDICATION OF THE PECULIAR TYPE OF HEAVY DUTY PERFORMANCE FOR WHICH THE FILAMENT IS RATED. SELECT REPLY CODE 10AE54 AFSYD 18TYPE,BEAM,LIGHT LIGHT BEAM TYPE THE ILLUMINATION PATTERN OF THE LIGHT BEAM PRODUCED BY THE ILLUMINATING SOURCE IN SURROUNDING SPACE. SELECT REPLY CODE 10AE55 AFSZD /D/ 19FEATURE,SURFACE,LAMP COVER LAMP COVER SURFACE FEATURE ANY SPECIFIC ALTERATION OR ARRANGEMENT OF THE LAMP COVER SURFACE WHEREBY THE TEXTURAL CONDITION,THE ILLUMINATION TYPE,AND/OR THE DEGREE OF TRANSPARENCY ARE VARIED TO PRODUCE A CERTAIN EFFECT. SELECT REPLY CODE 10AD35 AFTAD /D/ 07GLASS,RESISTANT,HEAT HEAT RESISTANT GLASS AN INDICATION OF WHETHER OR NOT A LOW EXPANSION GLASS THAT IS RESISTANT TO THERMAL CHANGE IS INCLUDED. SELECT REPLY CODE 10AA89 AFTBD /D/ 09MATERIAL,SLEEVE SLEEVE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SLEEVE IS FABRICATED. PLEASE USE MRC MATT WITH USE OF ISAC TBL 0094 IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AFTCB 10INPUT RATING IN WATT-SECONDS INPUT RATING IN WATT-SECONDS THE UNIT/S/ MEASURE OF THE INPUT RATING OF THE ITEM,WHEREIN A UNIT OF ELECTRICAL ENERGY IS EQUAL TO ONE WATT ACTING FOR ONE SECOND,EXPRESSED IN WATT-SECONDS /JOULES/. 1B MODE REPLY 0 AFTDA 10FLASHING RATE PER SECOND,MAXIMUM MAXIMUM FLASHING RATE PER SECOND THE MAXIMUM NUMBER OF FLASHES /PULSES/ PER SECOND AT WHICH THE ITEM IS DESIGNED TO OPERATE. 1A MODE REPLY 0 AFTED /D/ 11METHOD,STARTING,FLUORESCENT LAMP FLUORESCENT LAMP STARTING METHOD THE PRINCIPAL MEANS UTILIZED IN STARTING A FLUORESCENT LAMP. SELECT REPLY CODE 10AE56 AFTFA /D/ 16STYLE,SHAPE,ELECTRODE ELECTRODE SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ELECTRODE SHAPE. 1A MODE REPLY 0 AFTGD /D/ 19FLASH RATING,LAMP,PHOTOFLASH PHOTOFLASH LAMP FLASH RATING THE RATED FLASH CHARACTERISTIC OF A PHOTOFLASH LAMP AS DETERMINED BY HOW RAPIDLY THE LAMP REACHES ITS PEAK LIGHT INTENSITY,HOW MUCH LIGHT THE LAMP PRODUCES,AND HOW LONG THE BULB REMAINS AT OR NEAR ITS PEAK. SELECT REPLY CODE 10AE57 AFTHB 10TIME IN SECONDS,LIGHT,FLASH TO PEAK FLASH TO PEAK LIGHT TIME IN SECONDS THE NUMERIC VALUE INDICATING THE TIME INTERVAL REQUIRED,FROM THE TIME OF FLASH,FOR THE LIGHT TO REACH PEAK INTENSITY,EXPRESSED IN SECONDS. 1B MODE REPLY 0 AFTJB 10TEMP IN DEG KELVIN,COLOR COLOR TEMP IN DEG KELVIN THE NUMERIC VALUE INDICATING THE MEASUREMENT FOR THE COLOR TEMPERATURE OF THE LIGHT,EXPRESSED IN DEGREES KELVIN. 1B MODE REPLY 0 AFTKD /D/ 07LAMP,PREAGED PREAGED LAMP AN INDICATION OF WHETHER OR NOT THE LAMP HAS BEEN TESTED UNDER SPECIFIED OPERATING CONDITIONS FOR A PREDETERMINED PERIOD OF TIME. SELECT REPLY CODE 10AA89 AFTLA 19ARRANGEMENT,FORM,CONTACT CONTACT FORM ARRANGEMENT THE QUANTITY AND COMBINATION/S/ OF THE BASIC CONTACT FORMS,IN THE ORDER OF ASSEMBLAGE,WHICH MAKE UP THE SWITCHING STRUCTURE OF THE ITEM. 1A MODE REPLY 0 AFTMA 12QUANTITY,POSITION,SWITCH SWITCH POSITION QUANTITY THE NUMBER OF INDEXED POSITIONS TO WHICH THE SWITCH ACTUATOR MAY BE MOVED. 1A MODE REPLY 0 AFTND /D/ 19POSITIONS,FUNCTIONAL,SWITCH SWITCH FUNCTIONAL POSITIONS AN INDICATION OF THE VARIOUS FUNCTIONAL SWITCHING POSITIONS INCLUDED. SELECT REPLY CODE 10AE58 AFTPB 10VOLTAGE RATING IN VOLTS,AC,MAXIMUM MAXIMUM AC VOLTAGE RATING IN VOLTS THE HIGHEST ALTERNATING CURRENT VOLTAGE AT WHICH THE ITEM IS RATED FOR NORMAL OPERATION,EXPRESSED IN VOLTS. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 1B MODE REPLY 0 AFTQJ /D/ 10CURRENT RATING AT MAXIMUM AC VOLTAGE RATING,RESISTIVE LOAD,CONTACT CONTACT RESISTIVE LOAD CURRENT RATING AT MAXIMUM AC VOLTAGE RATING THE STATED VALUE OF CURRENT AT WHICH THE CONTACT/S/ IS RATED TO MAKE OR BREAK WITH A RESISTIVE LOAD,WHEN OPERATED AT THE RATED MAXIMUM ALTERNATING CURRENT VOLTAGE. 1D AND 1B MODE REPLY11AC30 AFTRJ /D/ 10CURRENT RATING AT MAXIMUM AC VOLTAGE RATING,INDUCTIVE LOAD,CONTACT CONTACT INDUCTIVE LOAD CURRENT RATING AT MAXIMUM AC VOLTAGE RATING THE STATED VALUE OF CURRENT AT WHICH THE CONTACT/S/ IS RATED TO MAKE OR BREAK WITH AN INDUCTIVE LOAD,WHEN OPERATED AT THE RATED MAXIMUM ALTERNATING CURRENT VOLTAGE. 1D AND 1B MODE REPLY11AC30 AFTSJ /D/ 10CURRENT RATING AT MAXIMUM AC VOLTAGE RATING,LAMP LOAD,CONTACT CONTACT LAMP LOAD CURRENT RATING AT MAXIMUM AC VOLTAGE RATING THE STATED VALUE OF CURRENT AT WHICH THE CONTACT/S/ IS RATED TO MAKE OR BREAK WITH A LAMP LOAD,WHEN OPERATED AT THE RATED MAXIMUM ALTERNATING CURRENT VOLTAGE. 1D AND 1B MODE REPLY11AC30 AFTTJ /D/ 10CURRENT RATING AT MAXIMUM AC VOLTAGE RATING,MOTOR LOAD,CONTACT CONTACT MOTOR LOAD CURRENT RATING AT MAXIMUM AC VOLTAGE RATING THE STATED VALUE OF CURRENT AT WHICH THE CONTACT/S/ IS RATED TO MAKE OR BREAK WITH A MOTOR LOAD,WHEN OPERATED AT THE RATED MAXIMUM ALTERNATING CURRENT VOLTAGE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 1D AND 1B MODE REPLY11AC30 AFTUJ 10POWER RATING AT MAXIMUM AC VOLTAGE RATING,ELECTRICAL ELECTRICAL POWER RATING AT MAXIMUM AC VOLTAGE RATING A MEASURE OF THE ALTERNATING CURRENT POWER HANDLING CAPABILITY OF AN ITEM. 1D AND 1B MODE REPLY11AC33 AFTVB 10VOLTAGE RATING IN VOLTS,DC,MAXIMUM MAXIMUM DC VOLTAGE RATING IN VOLTS THE HIGHEST DIRECT CURRENT VOLTAGE AT WHICH THE ITEM IS RATED FOR NORMAL OPERATION,EXPRESSED IN VOLTS.MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 1B MODE REPLY 0 AFTWJ /D/ 10CURRENT RATING AT MAXIMUM DC VOLTAGE RATING,RESISTIVE LOAD,CONTACT CONTACT RESISTIVE LOAD CURRENT RATING AT MAXIMUM DC VOLTAGE RATING THE STATED VALUE OF CURRENT AT WHICH THE CONTACT/S/ IS RATED TO MAKE OR BREAK WITH A RESISTIVE LOAD,WHEN OPERATED AT THE RATED MAXIMUM DIRECT CURRENT VOLTAGE. 1D AND 1B MODE REPLY11AC30 AFTXJ /D/ 10CURRENT RATING AT MAXIMUM DC VOLTAGE RATING,INDUCTIVE LOAD,CONTACT CONTACT INDUCTIVE LOAD CURRENT RATING AT MAXIMUM DC VOLTAGE RATING THE STATED VALUE OF CURRENT AT WHICH THE CONTACT/S/ IS RATED TO MAKE OR BREAK WITH AN INDUCTIVE LOAD,WHEN OPERATED AT THE RATED MAXIMUM DIRECT CURRENT VOLTAGE. 1D AND 1B MODE REPLY11AC30 AFTYJ /D/ 10CURRENT RATING AT MAXIMUM DC VOLTAGE RATING,LAMP LOAD,CONTACT CONTACT LAMP LOAD CURRENT RATING AT MAXIMUM DC VOLTAGE RATING THE STATED VALUE OF CURRENT AT WHICH THE CONTACT/S/ IS RATED TO MAKE OR BREAK WITH A LAMP LOAD,WHEN OPERATED AT THE RATED MAXIMUM DIRECT CURRENT VOLTAGE. 1D AND 1B MODE REPLY11AC30 AFTZJ /D/ 10CURRENT RATING AT MAXIMUM DC VOLTAGE RATING,MOTOR LOAD,CONTACT CONTACT MOTOR LOAD CURRENT RATING AT MAXIMUM DC VOLTAGE RATING THE STATED VALUE OF CURRENT AT WHICH THE CONTACT/S/ IS RATED TO MAKE OR BREAK WITH A MOTOR LOAD,WHEN OPERATED AT THE RATED MAXIMUM DIRECT CURRENT VOLTAGE. 1D AND 1B MODE REPLY11AC30 AFUAJ 10POWER RATING AT MAXIMUM DC VOLTAGE RATING,ELECTRICAL ELECTRICAL POWER RATING AT MAXIMUM DC VOLTAGE RATING A MEASURE OF THE DIRECT CURRENT POWER HANDLING CAPABILITY OF AN ITEM. 1D AND 1B MODE REPLY11AC33 AFUBB /D/ 10VOLTAGE RATING FOR MAXIMUM CURRENT RATING IN VOLTS,AC,CONTACT CONTACT AC VOLTAGE RATING FOR MAXIMUM CURRENT RATING IN VOLTS THE STATED VALUE OF ALTERNATING CURRENT VOLTAGE AT WHICH THE CONTACT/S/ IS RATED FOR ITS MAXIMUM CURRENT RATING,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AFUDJ /D/ 10CURRENT RATING,AC,CONTACT MAXIMUM INDUCTIVE LOAD CONTACT MAXIMUM INDUCTIVE LOAD AC CURRENT RATING THE GREATEST VALUE OF ALTERNATING CURRENT AT WHICH THE CONTACT/S/ IS RATED TO MAKE OR BREAK WITH AN INDUCTIVE LOAD. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 1D AND 1B MODE REPLY11AC30 AFUEJ /D/ 10CURRENT RATING,AC,CONTACT MAXIMUM LAMP LOAD CONTACT MAXIMUM LAMP LOAD AC CURRENT RATING THE GREATEST VALUE OF ALTERNATING CURRENT AT WHICH THE CONTACT/S/ IS RATED TO MAKE OR BREAK WITH A LAMP LOAD. 1D AND 1B MODE REPLY11AC30 AFUFJ /D/ 10CURRENT RATING,AC,CONTACT MAXIMUM MOTOR LOAD CONTACT MAXIMUM MOTOR LOAD AC CURRENT RATING THE GREATEST VALUE OF ALTERNATING CURRENT AT WHICH THE CONTACT/S/ IS RATED TO MAKE OR BREAK WITH A MOTOR LOAD 1D AND 1B MODE REPLY11AC30 AFUGB /D/ 10VOLTAGE RATING FOR MAXIMUM CURRENT RATING IN VOLTS,DC,CONTACT CONTACT DC VOLTAGE RATING FOR MAXIMUM CURRENT RATING IN VOLTS THE STATED VALUE OF DIRECT CURRENT VOLTAGE AT WHICH THE CONTACT/S/ IS RATED FOR ITS MAXIMUM CURRENT RATING,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AFUHJ /D/ 10CURRENT RATING,DC,CONTACT MAXIMUM RESISTIVE LOAD CONTACT MAXIMUM RESISTIVE LOAD DC CURRENT RATING THE GREATEST VALUE OF DIRECT CURRENT AT WHICH THE CONTACT/S/ IS RATED TO MAKE OR BREAK WITH A RESISTIVE LOAD. 1D AND 1B MODE REPLY11AC30 AFUJJ /D/ 10CURRENT RATING,DC,CONTACT MAXIMUM INDUCTIVE LOAD CONTACT MAXIMUM INDUCTIVE LOAD DC CURRENT RATING THE GREATEST VALUE OF DIRECT CURRENT AT WHICH THE CONTACT/S/ IS RATED TO MAKE OR BREAK WITH AN INDUCTIVE LOAD. 1D AND 1B MODE REPLY11AC30 AFULJ /D/ 10CURRENT RATING,DC,CONTACT MAXIMUM MOTOR LOAD CONTACT MAXIMUM MOTOR LOAD DC CURRENT RATING THE GREATEST VALUE OF DIRECT CURRENT AT WHICH THE CONTACT/S/ IS RATED TO MAKE OR BREAK WITH A MOTOR LOAD. 1D AND 1B MODE REPLY11AC30 AFUMJ /D/ 10CURRENT RATING,CONTINUOUS,CONTACT MAXIMUM CONTACT MAXIMUM CONTINUOUS CURRENT RATING THE GREATEST VALUE OF CURRENT THAT THE CONTACT/S/ IS RATED TO CARRY IN CONTINUOUS,NONMAKE/BREAK,OPERATION. 1D AND 1B MODE REPLY11AC30 AFUNJ 04DISTANCE BETWEEN COVER PLATE MOUNTING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN COVER PLATE MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AFUPD /D/ 18TYPE,FEATURE,INTERLOCKING,MULTIPLE ACTUATOR MULTIPLE ACTUATOR INTERLOCKING FEATURE TYPE A DESIGNATION THAT SPECIFIES THE KIND OF MECHANICAL INTERLOCKING FEATURE INCORPORATED IN THE ACTUATING MECHANISM. SELECT REPLY CODE 10AE59 AFUQL 16STYLE,ACTUATOR ACTUATOR STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ACTUATOR. 1L MODE REPLY 0 AFURJ 04DIAMETER,ACTUATOR ACTUATOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACTUATOR,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AFUSJ 04HEIGHT,ACTUATOR ACTUATOR HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AFUTJ 04WIDTH,ACTUATOR ACTUATOR WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ACTUATOR,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AFUUJ 04HEIGHT,POSITION,FREE,ACTUATOR ACTUATOR FREE POSITION HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AFUVJ 04DIAMETER,ROLLER,ACTUATOR ACTUATOR ROLLER DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFUWJ 04WIDTH,ROLLER,ACTUATOR ACTUATOR ROLLER WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFUXH 19RELATIONSHIP,POSITION-ACTION,ACTUATOR ACTUATOR POSITION-ACTION RELATIONSHIP THE RELATIONSHIP BETWEEN THE ACTUATOR POSITION AND THE ACTUATOR ACTION /MAINTAINED OR MOMENTARY/. 2D MODE REPLY 21AE601AE61 AFUYH 19RELATIONSHIP,POSITION-LOCKING,ACTUATOR ACTUATOR POSITION-LOCKING RELATIONSHIP THE RELATIONSHIP BETWEEN THE ACTUATOR POSITION AND THE INTEGRAL FACILITY DESIGNED TO PREVENT ACTUATOR MOVEMENT. 2D MODE REPLY 21AE601AE62 AFUZD 11METHOD,LUMINESCENT,ACTUATOR TIP ACTUATOR TIP LUMINESCENT METHOD THE MEANS BY WHICH THE END OF THE ACTUATOR IS CAUSED TO GLOW IN THE ABSENCE OF VISIBLE LIGHT AND WITHOUT BENEFIT OF ANY APPLIED ELECTRICAL POWER. SELECT REPLY CODE 10AB54 AFVAD 01COLOR,ACTUATOR ACTUATOR COLOR THE HUE OR TINT OF THE ACTUATOR. SELECT REPLY CODE 10AD06 AFVBD 01COLOR,ACTUATOR,ILLUMINATED ILLUMINATED ACTUATOR COLOR THE HUE OR TINT OF THE ACTUATOR WHEN ILLUMINATED BY AN INTEGRAL LIGHT SOURCE. SELECT REPLY CODE 10AD06 AFVCD /D/ 18TYPE ACCOMMODATED,LAMP,ACTUATOR ACTUATOR LAMP TYPE ACCOMMODATED INDICATES THE BASIC TYPE OF LAMP,USED FOR ACTUATOR ILLUMINATION,THAT THE SWITCH IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AD48 AFVEA 19INSCRIPTION,ACTUATOR ACTUATOR INSCRIPTION WORDS,LETTERS,NUMBERS,SYMBOLS,OR ANY COMBINATION THEREOF,PERMANENTLY INSCRIBED ON THE ACTUATOR,EXCLUDING THE PART NUMBER. 1A MODE REPLY 0 AFVFD /D/ 07ACCOMMODATION,WIRE,NEUTRAL,TERMINAL TERMINAL NEUTRAL WIRE ACCOMMODATION AN INDICATION OF WHETHER OR NOT AN ELECTRICALLY CONNECTED TERMINAL/S/ IS PROVIDED FOR THE THROUGH CONNECTION OF A NEUTRAL WIRE. SELECT REPLY CODE 10AB22 AFVGJ /D/ 10ACTUATING POINT IN AMPERE TURNS,SWITCH SWITCH ACTUATING POINT IN AMPERE TURNS THE RATED VALUE OF MAGNETOMOTIVE FORCE REQUIRED TO ACTUATE THE SWITCH. 1D AND 1B MODE REPLY11AC20 AFVHJ /D/ 10RELEASE POINT IN AMPERE TURNS,SWITCH SWITCH RELEASE POINT IN AMPERE TURNS THE RATED VALUE OF MAGNETOMOTIVE FORCE AT WHICH THE CONTACT/S/ WILL RETURN TO ITS UNACTUATED POSITION. 1D AND 1B MODE REPLY11AC20 AFVJJ /D/ 10FORCE,OPERATING,SWITCH ACTUATOR SWITCH ACTUATOR OPERATING FORCE THE AMOUNT OF LINEAR FORCE THAT MUST BE APPLIED TO THE SWITCH ACTUATOR TO CAUSE CONTACT OPERATION. 2D AND 1B MODE REPLY22AB161AC20 AFVKJ /D/ 10FORCE,RELEASE,SWITCH ACTUATOR SWITCH ACTUATOR RELEASE FORCE THE VALUE TO WHICH THE LINEAR FORCE APPLIED TO THE SWITCH ACTUATOR MUST BE REDUCED TO PERMIT THE CONTACT/S/ TO RETURN TO THE UNACTUATED POSITION. 2D AND 1B MODE REPLY22AB161AC20 AFVLJ /D/ 10TORQUE,OPERATING,SWITCH ACTUATOR SWITCH ACTUATOR OPERATING TORQUE THE AMOUNT OF ROTARY FORCE THAT MUST BE APPLIED TO THE SWITCH ACTUATOR TO CAUSE CONTACT OPERATION. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 2D AND 1B MODE REPLY21AA561AC20 AFVMJ /D/ 10TORQUE,RELEASE,SWITCH ACTUATOR SWITCH ACTUATOR RELEASE TORQUE THE VALUE TO WHICH THE ROTARY FORCE ON THE SWITCH ACTUATOR MUST BE REDUCED TO PERMIT THE CONTACT/S/ TO RETURN TO THE UNOPERATED POSITION. 2D AND 1B MODE REPLY21AA561AC20 AFVNJ /D/ 10PRETRAVEL,MOVEMENT,ACTUATOR,SWITCH SWITCH ACTUATOR MOVEMENT PRETRAVEL A MEASUREMENT OF MOVEMENT OF THE SWITCH ACTUATOR FROM ITS INITIAL UNACTUATED POSITION TO THE POINT OF CONTACT OPERATION. 2D AND 1B MODE REPLY21AA051AC20 AFVPJ /D/ 10PRETRAVEL IN DEG,MOVEMENT,SWITCH ACTUATOR SWITCH ACTUATOR MOVEMENT PRETRAVEL IN DEG THE ANGLE THROUGH WHICH THE SWITCH ACTUATOR TRAVELS FROM ITS INITIAL UNACTUATED POSITION TO THE POINT OF CONTACT ACTUATION,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 AFVQJ /D/ 10OVERTRAVEL,MOVEMENT,SWITCH ACTUATOR SWITCH ACTUATOR MOVEMENT OVERTRAVEL A MEASUREMENT OF THE MOVEMENT OF THE SWITCH ACTUATOR FROM THE POINT OF CONTACT OPERATION TO THE EXTREME POSITION TO WHICH THE ACTUATOR MAY BE MOVED. 2D AND 1B MODE REPLY21AA051AC20 AFVRJ /D/ 10OVERTRAVEL IN DEG,MOVEMENT,SWITCH ACTUATOR SWITCH ACTUATOR MOVEMENT OVERTRAVEL IN DEG THE ANGLE THROUGH WHICH THE SWITCH ACTUATOR TRAVELS FROM THE POINT OF CONTACT OPERATION TO THE EXTREME POSITION TO WHICH THE ACTUATOR MAY BE MOVED,EXPRESSED IN DEGREES. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 1D AND 1B MODE REPLY11AC20 AFVSJ 10DIFFERENTIAL,MOVEMENT,SWITCH ACTUATOR SWITCH ACTUATOR MOVEMENT DIFFERENTIAL A MEASUREMENT OF THE MOVEMENT OF THE SWITCH ACTUATOR WHEN RETURNING FROM THE POINT OF CONTACT OPERATION TO THE POINT OF CONTACT RELEASE. MRC DISCONTINUED FOR GERNAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 2D AND 1B MODE REPLY21AA051AC20 AFVTJ /D/ 10DIFFERENTIAL IN DEG,MOVEMENT,ACTUATOR,SWITCH SWITCH ACTUATOR MOVEMENT DIFFERENTIAL IN DEG THE ANGLE THROUGH WHICH THE SWITCH ACTUATOR TRAVELS WHEN RETURNING FROM THE POINT OF CONTACT OPERATION TO THE POINT OF CONTACT RELEASE,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 AFVUJ /D/ 04ANGLE IN DEG,DIFFERENTIAL,ACTUATION,SWITCH SWITCH ACTUATION DIFFERENTIAL ANGLE IN DEG THE AMOUNT OF SWITCH MOVEMENT REQUIRED TO EFFECT THE SWITCHING ACTION,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 AFVVL 16STYLE,ADAPTER,ACTUATOR ACTUATOR ADAPTER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ACTUATOR ADAPTER. 1L MODE REPLY 0 AFVWJ /D/ 04DIAMETER,BUSHING,ADAPTER ADAPTER BUSHING DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFVXJ 04LENGTH,BUSHING,ADAPTER ADAPTER BUSHING LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFVYJ 04DISTANCE BETWEEN ADAPTER MOUNTING FACILITIES PARALLEL TO LENGTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN ADAPTER MOUNTING FACILITIES PARALLEL TO LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFVZJ /D/ 04DIAMETER,HOLE,MOUNTING,ADAPTER ADAPTER MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFWAL /D/ 16STYLE,HOUSING,SENSITIVE SWITCH SENSITIVE SWITCH HOUSING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARNACE OF THE SENSITIVE SWITCH HOUSING. 1L MODE REPLY 0 AFWBJ 04DIAMETER,HOUSING HOUSING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOUSING, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AFWCJ 04HEIGHT,HOUSING HOUSING HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AFWDJ 04LENGTH,HOUSING HOUSING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE HOUSING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AFWEJ 04WIDTH,HOUSING HOUSING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A HOUSING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AFWFJ 04LENGTH,BUSHING,HOUSING HOUSING BUSHING LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFWGJ 04DISTANCE BETWEEN HOUSING MOUNTING FACILITIES PARALLEL TO HEIGHT,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN HOUSING MOUNTING FACILITIES PARALLEL TO HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AFWHJ 04DISTANCE BETWEEN HOUSING MOUNTING FACILITIES PARALLEL TO LENGTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN HOUSING MOUNTING FACILITIES PARALLEL TO LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFWJJ 04DISTANCE BETWEEN HOUSING MOUNTING FACILITIES PARALLEL TO WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN HOUSING MOUNTING FACILITIES PARALLEL TO WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFWKJ /D/ 04DIAMETER,HOLE,MOUNTING,HOUSING HOUSING MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFWLD 18TYPE ACCOMMODATED,FUSE FUSE TYPE ACCOMMODATED INDICATES THE TYPE OF FUSE THE ITEM IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AE67 AFWMB /D/ 10ALTITUDE RATING IN FEET,OPERATING,MAXIMUM,SWITCH SWITCH MAXIMUM OPERATING ALTITUDE RATING IN FEET THE MAXIMUM ALTITUDE AT WHICH A SWITCH IS RATED TO MAKE AND BREAK A SPECIFIED CONTACT CURRENT,EXPRESSED IN FEET. 1B MODE REPLY 0 AFWND /D/ 07SEAL,ACTUATOR ACTUATOR SEAL AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES AN INTERNAL AND INTEGRAL INSERT BONDED TO THE ACTUATOR AND THE CASE TO PREVENT THE ENTRANCE OF FOREIGN MATTER INTO THE ACTUATOR. SELECT REPLY CODE 10AA49 AFWPJ /D/ 04LENGTH,OVERALL,CABLE CABLE OVERALL LENGTH THE OVERALL LENGTH OF THE CABLE PROVIDED FOR ELECTRICAL CONNECTION,INCLUDING ANY TERMINATING CONNECTOR. 2D AND 1B MODE REPLY21AA051AC20 AFWQJ /D/A13THREAD SIZE,COUPLING,ELECTRICAL CONDUIT ELECTRICAL CONDUIT COUPLING THREAD SIZE THE THREAD SERIES,THREAD MAJOR/MAXIMUM DIAMETER,AND THE NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE OF A BUSHING OR OTHER FACILITY PROVIDED TO ACCOMMODATE A CONDUIT COUPLING NUT. 1D AND 1A MODE REPLY12AC21 AFWRA 10LIFE IN CYCLES,OPERATIONAL,ACTUATING DEVICE ACTUATING DEVICE OPERATIONAL LIFE IN CYCLES THE MAXIMUM NUMBER OF COMPLETE CYCLES THAT THE ACTUATING DEVICE OF THE ITEM IS RATED TO WITHSTAND WITHOUT RESULTING IN ANY PERMANENT CHANGES IN ITS MECHANICAL OR ELECTRICAL CHARACTERISTICS. 1A MODE REPLY 0 AFWSJ /D/ 10STRENGTH,TERMINAL TERMINAL STRENGTH THE MAXIMUM FORCE THE TERMINALS ARE TESTED TO WITHSTAND WITHOUT RESULTING IN ANY PERMANENT CHANGES IN THE MECHANICAL OR ELECTRICAL CHARACTERISTICS OF THE ITEM. 1D AND 1B MODE REPLY12AB16 AFWTG 19SEQUENCE,COLOR,ACTUATOR ACTUATOR COLOR SEQUENCE THE ACTUAL ORDER OF ACTUATOR COLORS IN RELATION TO ACTUATOR ORIENTATION OR POSITIONS. FULL TEXT WRITE-IN 0 AFWUG 19SEQUENCE,COLOR,ILLUMINATED ACTUATOR ILLUMINATED ACTUATOR COLOR SEQUENCE THE ACTUAL ORDER OF ILLUMINATED ACTUATOR COLORS IN RELATION TO ACTUATOR ORIENTATION OR POSITIONS. FULL TEXT WRITE-IN 0 AFWWJ 04WIDTH,TERMINAL TERMINAL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TERMINAL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AFWXJ 04DISTANCE BETWEEN INSIDE MOUNTING FACILITIES PARALLEL TO LENGTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN INSIDE MOUNTING FACILITIES PARALLEL TO LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFWYJ 04THICKNESS,TERMINAL TERMINAL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE TERMINAL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AFWZJ /D/ 04DISTANCE BETWEEN SPLIT TERMINALS DISTANCE BETWEEN SPLIT TERMINALS NONE. 2D AND 1B MODE REPLY21AA051AC20 AFXAJ /D/ 04DISTANCE BETWEEN INSIDE MOUNTING FACILITIES PARALLEL TO WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN INSIDE MOUNTING FACILITIES PARALLEL TO WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFXBJ 04WIDTH,TAB TAB WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFXCJ /D/ 04DISTANCE BETWEEN TAB AND END OF FERRULE DISTANCE BETWEEN TAB AND END OF FERRULE NONE. 2D AND 1B MODE REPLY21AA051AC20 AFXDF T10RANGE IN AMPS,CURRENT CURRENT RANGE IN AMPS THE MINIMUM AND MAXIMUM CURRENT RATING FOR WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN AMPERES. 1F MODE REPLY 0 AFXEJ 10VOLTAGE RATING IN VOLTS,MAXIMUM MAXIMUM VOLTAGE RATING IN VOLTS THE MAXIMUM VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE IN AN ALTERNATING CURRENT AND/OR DIRECT CURRENT CIRCUIT,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AE16 AFXFD 18TYPE,INTERRUPTION,OVER-CURRENT,CIRCUIT CIRCUIT OVER-CURRENT INTERRUPTION TYPE INDICATES THE TYPE OF OVER-CURRENT CONDITIONS THAT AN ITEM IS DESIGNED TO WITHSTAND INDICATED BY THE SPEED OF CIRCUIT INTERRUPTION. SELECT REPLY CODE 10AE68 AFXGJ /D/ 10TIME IN SECONDS,DELAY,INTERRUPTION,CIRCUIT OVER-CURRENT CIRCUIT OVER-CURRENT INTERRUPTION DELAY TIME IN SECONDS THE TIME ELAPSING BEFORE CIRCUIT INTERRUPTION OF AN ITEM OPERATED AT A SPECIFIED PERCENT OF ITS NORMAL CURRENT RATING,EXPRESSED IN SECONDS. 1D AND 1B MODE REPLY11AE69 AFXHD 11METHOD,INDICATOR,INTERRUPTION INTERRUPTION INDICATOR METHOD THE MEANS IN WHICH THE ITEM SIGNALS THE INTERRUPTION OF A CIRCUIT. SELECT REPLY CODE 10AE70 AFXJB /D/ 10CAPACITY IN AMPS,INTERRUPTING,MAXIMUM MAXIMUM INTERRUPTING CAPACITY IN AMPS THE MAXIMUM SHORT CIRCUIT CURRENT THAT A PROTECTIVE DEVICE WILL INTERRUPT WITHOUT DETERIORATION OF THE DIELECTRIC MATERIAL AT THE SPECIFIED RATED VOLTAGE,EXPRESSED IN AMPERES. 1B MODE REPLY 0 AFXKB /D/ 10RESISTANCE IN OHMS,ELEMENT,FUSIBLE,MAXIMUM MAXIMUM FUSIBLE ELEMENT RESISTANCE IN OHMS THE MAXIMUM INTERNAL RESISTANCE AS MEASURED AT THE TERMINALS OF THE FUSE WHEN THE RATED CURRENT IS BEING CARRIED,EXPRESSED IN OHMS. 1B MODE REPLY 0 AFXLD /D/ 07ELEMENT,FUSIBLE,RENEWABLE RENEWABLE FUSIBLE ELEMENT AN INDICATION OF WHETHER OR NOT THE ELEMENT IS RENEWABLE. SELECT REPLY CODE 10AA89 AFXMJ 10TEMP,MELTING,ELEMENT ELEMENT MELTING TEMP THE TEMPERATURE AT WHICH THE THERMAL ELEMENT WILL MELT TO INTERRUPT THE CIRCUIT. 1D AND 1B MODE REPLY11AB36 AFXND 18TYPE,FUNCTION,DUMMY FUSE DUMMY FUSE FUNCTION TYPE INDICATES THE TYPE OF CONNECTION OR CIRCUITRY WHICH THE FUSE PROVIDES BETWEEN ITS TERMINALS;I.E.,EITHER A SOLID NONFUSIBLE CONDUCTOR OR NO CONNECTION/OPEN. SELECT REPLY CODE 10AC59 AFXPA 12QUANTITY,FINGER FINGER QUANTITY THE NUMBER OF FINGERS PROVIDED WITH THE ITEM. 1A MODE REPLY 0 AFXQD 18TYPE,FINGER FINGER TYPE INDICATES THE TYPE OF FINGER(S) PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AE71 AFXRA 12QUANTITY,ACCOMMODATION,FINGER FINGER ACCOMMODATION QUANTITY THE NUMBER OF FINGERS ACCOMMODATED BY THE ITEM. 1A MODE REPLY 0 AFXSD 18TYPE,FINGER,ACCOMMODATED ACCOMMODATED FINGER TYPE INDICATES THE TYPE OF FINGER/S/ ACCOMMODATED BY THE ITEM. SELECT REPLY CODE 10AE71 AFXTD /D/ 09MATERIAL,FINGER FINGER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FINGER IS FABRICATED. SELECT REPLY CODE 10AD09 AFXUD /D/ 17SURFACE TREATMENT,FINGER FINGER SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE FINGER SURFACE. SELECT REPLY CODE 10AD09 AFXVD /D/ 17SURFACE TREATMENT,SPRING,CONTACT CONTACT SPRING SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE CONTACT SPRING SURFACE. SELECT REPLY CODE 10AD09 AFXWJ 04LENGTH,FINGER FINGER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFXXJ 04DIAMETER,FINGER FINGER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FINGER, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AFXYJ 04DIAMETER,ACCOMMODATION,FINGER FINGER ACCOMMODATION DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE FINGER, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AFXZJ 04LENGTH,ACCOMMODATION,FINGER FINGER ACCOMMODATION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFYAD /D/ 09MATERIAL,SPRING,CONTACT CONTACT SPRING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CONTACT SPRING IS FABRICATED. SELECT REPLY CODE 10AD09 AFYBJ 04DISTANCE BETWEEN FINGERS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FINGERS THE CENTER TO CENTER DISTANCE BETWEEN THE FINGERS. 2D AND 1B MODE REPLY21AA051AC20 AFYCJ 04DISTANCE BETWEEN FINGER ACCOMMODATIONS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FINGER ACCOMMODATIONS NONE. 2D AND 1B MODE REPLY21AA051AC20 AFYDJ /D/ 04DISTANCE BETWEEN MOUNTING HOLES/SLOTS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES/SLOTS NONE. 2D AND 1B MODE REPLY21AA051AC20 AFYEJ 04DIAMETER,MOUNTING,BUSHING MOUNTING BUSHING DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFYFJ 04LENGTH,LEG,MOUNTING MOUNTING LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFYGD /D/ 07HANDLE HANDLE AN INDICATION OF WHETHER OR NOT THE ITEM IS FURNISHED WITH A HANDLE. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA55 AFYHD /D/ 09MATERIAL,HANDLE HANDLE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HANDLE IS FABRICATED. USE MRC MATT AND ISAC TO TABLE 0060. SELECT REPLY CODE 10AD09 AFYJD /D/ 17SURFACE TREATMENT,HANDLE HANDLE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A HANDLE SURFACE. USE MRC SFTT AND ISAC TO TABLE 0060. SELECT REPLY CODE 10AD09 AFYKA 12QUANTITY,HOLE/SLOT,MOUNTING MOUNTING HOLE/SLOT QUANTITY THE NUMBER OF HOLES/SLOTS PROVIDED FOR ATTACHMENT OF THE ITEM. 1A MODE REPLY 0 AFYLD /D/ 09MATERIAL,BUSHING,MOUNTING MOUNTING BUSHING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MOUNTING BUSHING IS FABRICATED. SELECT REPLY CODE 10AD09 AFYMJ 04DIAMETER,ACCOMMODATION,BUSHING THRU-HOLE BUSHING THRU-HOLE ACCOMMODATION DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFYND /D/ 11METHOD,DISCONNECT,QUICK,REMOTE REMOTE QUICK DISCONNECT METHOD THE MEANS BY WHICH QUICK DISCONNECT IS ACHIEVED THROUGH REMOTE ACTION. SELECT REPLY CODE 10AE72 AFYPJ 04LENGTH,ACCOMMODATION,BUSHING THRU-HOLE BUSHING THRU-HOLE ACCOMMODATION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFYQJ 04WIDTH,ACCOMMODATION,BUSHING THRU-HOLE BUSHING THRU-HOLE ACCOMMODATION WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFYRJ 04DISTANCE BETWEEN BUSHING THRU-HOLE ACCOMMODATIONS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN BUSHING THRU-HOLE ACCOMMODATIONS NONE. 2D AND 1B MODE REPLY21AA051AC20 AFYSJ 04LENGTH,KEYWAY KEYWAY LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A KEYWAY,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AFYTD /D/ 07PROVISION,ATTACHMENT,CABLE CABLE ATTACHMENT PROVISION AN INDICATION OF WHETHER OR NOT A MEANS IS PROVIDED FOR SECURING THE CABLE TO THE ITEM. SELECT REPLY CODE 10AB22 AFYUD 18TYPE,ELEMENT ELEMENT TYPE INDICATES THE TYPE OF ELEMENT/CARTRIDGE AS DETERMINED BY ITS CONSTRUCTION AND METHOD OF OPERATION. SELECT REPLY CODE 10AE76 AFYVJ 10RESISTANCE RATING IN OHMS,DC DC RESISTANCE RATING IN OHMS THE OPPOSITION TO THE FLOW OF DIRECT CURRENT OFFERED BY AN ITEM,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 AFYWF T10RANGE IN HERTZ,RESPONSE,FREQUENCY FREQUENCY RESPONSE RANGE IN HERTZ THE MINIMUM AND MAXIMUM FREQUENCIES TO WHICH THE ITEM WILL RESPOND,EXPRESSED IN HERTZ. 1F MODE REPLY 0 AFYXD 11METHOD,SELECTION,IMPEDANCE IMPEDANCE SELECTION METHOD THE MEANS USED TO SELECT THE OUTPUT IMPEDANCE OF THE ITEM. SELECT REPLY CODE 10AE73 AFYYJ 10IMPEDANCE RATING IMPEDANCE RATING THE TOTAL OPPOSITION /RESISTIVE AND REACTIVE/ TO THE FLOW OF ALTERNATING CURRENT. 2D AND 1B MODE REPLY22AE751AC20 AFZAB 10SENSITIVITY RATING IN DECIBELS,OUTPUT OUTPUT SENSITIVITY RATING IN DECIBELS THE RATING INDICATING THE RATIO OF THE OUTPUT VOLTAGE OR POWER TO THE INPUT VOLTAGE OR POWER AT A SPECIFIED REFERENCE ENERGY LEVEL,EXPRESSED IN DECIBELS. 1B MODE REPLY 0 AFZBD 10REFERENCE,SENSITIVITY RATING,OUTPUT OUTPUT SENSITIVITY RATING REFERENCE THE ELECTRICAL OUTPUT RATING AND SOUND PRESSURE INPUT RATING WHICH ARE USED AS A BASE REFERENCE FOR THE MEASUREMENT OF THE SENSITIVITY OF AN ITEM. SELECT REPLY CODE 10AF28 AFZCD 19FUNCTION FOR WHICH DESIGNED FUNCTION FOR WHICH DESIGNED THE SPECIFIC PURPOSE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AE74 AFZDJ 10VOLTAGE RATING,AC,OUTPUT OUTPUT AC VOLTAGE RATING THE ALTERNATING CURRENT POTENTIAL FOR WHICH THE ITEM IS RATED,REFLECTED AT THE OUTPUT OF THE ITEM. 2D AND 1B MODE REPLY21AB631AC20 AFZEB 10VOLTAGE IN VOLTS,DC,OPERATING OPERATING DC VOLTAGE IN VOLTS THE DIRECT CURRENT POTENTIAL WHICH MUST BE APPLIED TO AN ITEM TO OBTAIN ITS RATED PERFORMANCE,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AFZFJ /D/ 10CIRCUIT LOAD VALUE CIRCUIT LOAD VALUE THE VALUE OF THE LOAD FURNISHED TO A CIRCUIT BY THE SPECIFIC FUNCTIONAL DESIGN USED. 1D AND 1B MODE REPLY12AE75 AFZGD /D/ 07FEATURE,LOCKING,SAFETY SAFETY LOCKING FEATURE AN INDICATION OF WHETHER OR NOT A MECHANICAL MEANS IS USED TO PREVENT ACCIDENTAL DISENGAGEMENT OF THE ITEM FROM ITS MATING COUNTERPART. SELECT REPLY CODE 10AA49 AFZHB 10CAPACITANCE IN PICOFARADS CAPACITANCE IN PICOFARADS THE ELECTRICAL CAPACITANCE AS MEASURED BETWEEN TWO SPECIFIED POINTS OF THE ITEM,EXPRESSED IN PICOFARADS. 1B MODE REPLY 0 AFZJB /D/ 10IMPEDANCE RATING IN OHMS,TYPE,COAXIAL COAXIAL TYPE IMPEDANCE RATING IN OHMS THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) WHICH THE ITEM OFFERS TO THE FLOW OF ALTERNATING CURRENT,EXPRESSED IN OHMS. 1B MODE REPLY 0 AFZKA 03DESIGNATOR,ARRANGEMENT,JACK CONTACT JACK CONTACT ARRANGEMENT DESIGNATOR A DESIGNATION OF THE DESCRIPTION OF THE RELATIVE POSITION OF THE CONTACTS IN RELATIONSHIP TO EACH OTHER AND TO THE BODY. 1A MODE REPLY 0 AFZLJ 04DIAMETER,INSIDE,EXPANDED EXPANDED INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFZMJ 04DIAMETER,INSIDE,RECOVERED RECOVERED INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFZNJ 04THICKNESS,WALL,RECOVERED RECOVERED WALL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AFZPJ 04THICKNESS OF MAIN BODY,WALL,LARGE END LARGE END WALL THICKNESS OF MAIN BODY NONE. 2D AND 1B MODE REPLY21AA051AC20 AFZQJ 04THICKNESS OF MAIN BODY,WALL,SMALL END SMALL END WALL THICKNESS OF MAIN BODY NONE. 2D AND 1B MODE REPLY21AA051AC20 AFZRJ 04DISTANCE FROM INTERSECTING CENTERLINES TO EDGE OF SMALL END DISTANCE FROM INTERSECTING CENTERLINES TO EDGE OF SMALL END NONE. 2D AND 1B MODE REPLY21AA051AC20 AFZSJ 04DISTANCE FROM CENTERLINE OF SMALL END TO EDGE OF LARGE END DISTANCE FROM CENTERLINE OF SMALL END TO EDGE OF LARGE END NONE. 2D AND 1B MODE REPLY21AA051AC20 AFZTJ 04DISTANCE FROM CENTERLINE OF MAIN BODY TO END OF FIRST BRANCH DISTANCE FROM CENTERLINE OF MAIN BODY TO END OF FIRST BRANCH NONE. 2D AND 1B MODE REPLY21AA051AC20 AFZUJ 04DIAMETER,INSIDE,MAIN BODY MAIN BODY INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFZVJ 04DIAMETER,INSIDE,FIRST BRANCH FIRST BRANCH INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFZWJ 04DIAMETER,INSIDE,SECOND BRANCH SECOND BRANCH INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFZXJ 04DIAMETER,INSIDE,THIRD BRANCH THIRD BRANCH INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFZYJ 04DIAMETER,INSIDE,FOURTH BRANCH FOURTH BRANCH INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AFZZJ 04DISTANCE FROM INTERSECTING CENTERLINE OF MAIN BODY TO END OF SECOND BRANCH DISTANCE FROM INTERSECTING CENTERLINE OF MAIN BODY TO END OF SECOND BRANCH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGAAJ 04DISTANCE FROM INTERSECTING CENTERLINE OF MAIN BODY TO END OF FIRST BRANCH DISTANCE FROM INTERSECTING CENTERLINE OF MAIN BODY TO END OF FIRST BRANCH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGABJ 04THICKNESS,WALL,MAIN BODY MAIN BODY WALL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGACJ 04THICKNESS,WALL,FIRST BRANCH FIRST BRANCH WALL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGADJ 04THICKNESS,WALL,SECOND BRANCH SECOND BRANCH WALL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGAEJ 04THICKNESS,WALL,THIRD BRANCH THIRD BRANCH WALL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGAFJ 04THICKNESS,WALL,FOURTH BRANCH FOURTH BRANCH WALL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGAGJ 04DISTANCE FROM EDGE OF MAIN BODY TO INTERSECTING CENTERLINES DISTANCE FROM EDGE OF MAIN BODY TO INTERSECTING CENTERLINES NONE. 2D AND 1B MODE REPLY21AA051AC20 AGAHJ 04LENGTH,OVERALL,MAIN BODY MAIN BODY OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGAJJ 04DIAMETER,INSIDE,SMALL END,MAIN BODY MAIN BODY SMALL END INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGAKJ 04DIAMETER,INSIDE,LARGE END,MAIN BODY MAIN BODY LARGE END INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGALJ 04DISTANCE FROM BOTTOM OF SHOULDER TO LARGE END OF MAIN BODY DISTANCE FROM BOTTOM OF SHOULDER TO LARGE END OF MAIN BODY NONE. 2D AND 1B MODE REPLY21AA051AC20 AGAMJ 04DISTANCE FROM TOP OF SHOULDER TO SMALL END OF MAIN BODY DISTANCE FROM TOP OF SHOULDER TO SMALL END OF MAIN BODY NONE. 2D AND 1B MODE REPLY21AA051AC20 AGANJ /D/ 04DISTANCE FROM CENTERLINE OF MAIN BODY TO EDGE OF SMALL END DISTANCE FROM CENTERLINE OF MAIN BODY TO EDGE OF SMALL END NONE. 2D AND 1B MODE REPLY21AA051AC20 AGAPJ 04ANGLE BETWEEN LARGE END AND SMALL END CENTERLINES IN DEG ANGLE BETWEEN LARGE END AND SMALL END CENTERLINES IN DEG NONE. 1D AND 1B MODE REPLY11AC20 AGAQJ 04ANGLE BETWEEN MAIN BODY AND FIRST BRANCH CENTERLINES IN DEG ANGLE BETWEEN MAIN BODY AND FIRST BRANCH CENTERLINES IN DEG NONE. 1D AND 1B MODE REPLY11AC20 AGARJ 04ANGLE BETWEEN MAIN BODY AND SECOND BRANCH CENTERLINES IN DEG ANGLE BETWEEN MAIN BODY AND SECOND BRANCH CENTERLINES IN DEG NONE. 1D AND 1B MODE REPLY11AC20 AGAUB 10SHRINKAGE RATING IN PERCENT,HEAT HEAT SHRINKAGE RATING IN PERCENT THE PERCENTAGE AN ITEM IS RATED TO REDUCE IN SIZE UPON THE APPLICATION OF HEAT. 1B MODE REPLY 0 AGAVG 19IDENTIFICATION,ITEM,END END ITEM IDENTIFICATION THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART. FULL TEXT WRITE-IN 0 AGAWJ 04DISTANCE BETWEEN MOUNTING SLOTS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING SLOTS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGAXD 07CONNECTION,POLARITY POLARITY CONNECTION AN INDICATION OF WHETHER OR NOT THE ITEM REQUIRES A SPECIFIC POLARITY FOR CONNECTION INTO THE OPERATING CIRCUIT. SELECT REPLY CODE 10AE40 AGAYD 18TYPE,DIRECTIONAL,SOUND PICKUP SOUND PICKUP DIRECTIONAL TYPE INDICATES THE SPECIFIC TYPE OF SOUND PICKUP WHICH DETERMINES THE PERFORMANCE OF THE ITEM. SELECT REPLY CODE 10AE78 AGAZD /D/ 07FEATURE,CANCELING,NOISE NOISE CANCELING FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE IS INCLUDED TO ENABLE THE ITEM TO CANCEL UNDESIRABLE BACKGROUND SOUNDS. SELECT REPLY CODE 10AA49 AGBAD /D/ 07STAND,SUPPORT SUPPORT STAND AN INDICATION OF WHETHER OR NOT A SUPPORT STAND IS INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA49 AGBBJ 04HEIGHT,STAND,SUPPORT SUPPORT STAND HEIGHT THE DIMENSION OF THE STAND FROM ITS BASE TO THE POINT WHERE THE CONNECTION FACILITY IS LOCATED. 2D AND 1B MODE REPLY21AA051AC20 AGBCD /D/ 07MOUNT,SHOCK SHOCK MOUNT AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A SELF-CONTAINED SHOCK MOUNT. SELECT REPLY CODE 10AB22 AGBDD 18TYPE,CONNECTION,ELECTRICAL ELECTRICAL CONNECTION TYPE INDICATES THE TYPE OF ELECTRICAL CONNECTION INCLUDED ON THE ITEM. SELECT REPLY CODE 10AE79 AGBED /D/ 09MATERIAL,IMPREGNATION IMPREGNATION MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE WITH WHICH THE ITEM IS SATURATED. PLEASE USE MRC CXKJ IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AGBFD /D/ 07PROVISION,ENCAPSULATION ENCAPSULATION PROVISION AN INDICATION OF WHETHER OR NOT MATERIAL WHICH MELTS UPON THE APPLICATION OF HEAT TO PROVIDE ENCAPSULATION OF THE INSERTED ITEM IS INCLUDED. SELECT REPLY CODE 10AA89 AGBGA 19IDENTIFICATION,CONNECTOR CONNECTOR IDENTIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURER'S NUMBER OR SYMBOL USED TO IDENTIFY THE CONNECTOR. 1A MODE REPLY 0 AGBHA 19IDENTIFICATION,CABLE CABLE IDENTIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS IDENTIFICATION NUMBER OR SYMBOL USED TO IDENTIFY THE CABLE. 1A MODE REPLY 0 AGBJJ 04LENGTH,CABLE,EXTENDED EXTENDED CABLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CABLE OR CORD WHEN FULLY EXTENDED. 2D AND 1B MODE REPLY21AA051AC20 AGBKJ 04LENGTH,CABLE,RETRACTED RETRACTED CABLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CABLE OR CORD WHEN RETRACTED OR IN NORMAL UNEXTENDED CONDITION. 2D AND 1B MODE REPLY21AA051AC20 AGBLA 12QUANTITY,CONDUCTOR,CABLE CABLE CONDUCTOR QUANTITY THE NUMBER OF CONDUCTORS,SHIELDED AND UNSHIELDED,WHICH MAKE UP THE CABLE. 1A MODE REPLY 0 AGBMA 12QUANTITY,CONDUCTOR,SHIELDED,CABLE CABLE SHIELDED CONDUCTOR QUANTITY THE NUMBER OF INSULATED CONDUCTORS WITHIN THE CABLE THAT ARE INCLOSED IN AN ELECTRICAL SHIELD. 1A MODE REPLY 0 AGBNA 19CODE,MANUFACTURER,CABLE CABLE MANUFACTURER CODE THE IDENTIFYING ALPHA/NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS DESIGN OR MANUFACTURERS THE CABLE. 1A MODE REPLY 0 AGBPJ 04HEIGHT,LIFT,MAXIMUM MAXIMUM LIFT HEIGHT THE MAXIMUM HEIGHT THE ITEM IS CAPABLE OF RAISING AN OBJECT. 1D AND 1B MODE REPLY11AA05 AGBQJ 04WIDTH,PLATFORM,LOAD LOAD PLATFORM WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGBRJ 04LENGTH,PLATFORM,LOAD LOAD PLATFORM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE LOAD PLATFORM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AGBSJ 04LENGTH,FORK FORK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A FORK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AGBTJ 04WIDTH,FORK FORK WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A FORK,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AGBUJ 04DISTANCE BETWEEN STATIONARY FORKS DISTANCE BETWEEN STATIONARY FORKS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGBVJ 04HEIGHT WITH FORKS IN LOWEST POSITION,OVERALL OVERALL HEIGHT WITH FORKS IN LOWEST POSITION NONE. 2D AND 1B MODE REPLY21AA051AC20 AGBWJ 04HEIGHT WITH FORKS IN HIGHEST POSITION,OVERALL OVERALL HEIGHT WITH FORKS IN HIGHEST POSITION NONE. 2D AND 1B MODE REPLY21AA051AC20 AGBXJ 04LENGTH WITHOUT FORKS,OVERALL OVERALL LENGTH WITHOUT FORKS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGBYJ 04LENGTH WITH FORKS RETRACTED,OVERALL OVERALL LENGTH WITH FORKS RETRACTED NONE. 2D AND 1B MODE REPLY21AA051AC20 AGBZJ 04WIDTH WITH FORKS RETRACTED,OVERALL OVERALL WIDTH WITH FORKS RETRACTED NONE. 2D AND 1B MODE REPLY21AA051AC20 AGCAJ 04LENGTH,COMPARTMENT,BATTERY BATTERY COMPARTMENT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BATTERY COMPARTMENT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AGCBJ 04WIDTH,COMPARTMENT,BATTERY BATTERY COMPARTMENT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BATTERY COMPARTMENT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AGCCJ 04DEPTH,COMPARTMENT,BATTERY BATTERY COMPARTMENT DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE BATTERY COMPARTMENT,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AGCDJ /D/ 04LENGTH,PLATFORM,FRONT LOAD FRONT LOAD PLATFORM LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGCEJ /D/ 04LENGTH,PLATFORM,REAR LOAD REAR LOAD PLATFORM LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGCFJ /D/ 04LENGTH BETWEEN PLATFORMS,BAY,LOADER LOADER BAY LENGTH BETWEEN PLATFORMS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGCGJ 04LENGTH,MAXIMUM,REACH REACH MAXIMUM LENGTH A MEASUREMENT OF THE MAXIMUM LENGTH THE ITEM IS CAPABLE OF REACHING. 1D AND 1B MODE REPLY11AA05 AGCHJ 04DEPTH BELOW GRADE LEVEL,REACH,MAXIMUM MAXIMUM REACH DEPTH BELOW GRADE LEVEL A MEASUREMENT OF THE DISTANCE BELOW GRADE LEVEL THE ITEM WILL REACH. 1D AND 1B MODE REPLY11AA05 AGCJB /D/ 04ANGLE IN DEG,TILT,FORWARD BOOM FORWARD BOOM TILT ANGLE IN DEG NONE. 1B MODE REPLY 0 AGCKB /D/ 04ANGLE IN DEG,TILT,BACKWARD BOOM BACKWARD BOOM TILT ANGLE IN DEG NONE. 1B MODE REPLY 0 AGCLB /D/ 04ANGLE IN DEG,TILT,FORWARD FORK FORWARD FORK TILT ANGLE IN DEG NONE. 1B MODE REPLY 0 AGCMB /D/ 04ANGLE IN DEG,TILT,BACKWARD FORK BACKWARD FORK TILT ANGLE IN DEG NONE. 1B MODE REPLY 0 AGCNJ 04HEIGHT WITH PLATFORM IN LOWEST POSITION,OVERALL OVERALL HEIGHT WITH PLATFORM IN LOWEST POSITION NONE. 2D AND 1B MODE REPLY21AA051AC20 AGCPJ 04HEIGHT WITH PLATFORM IN HIGHEST POSITION,OVERALL OVERALL HEIGHT WITH PLATFORM IN HIGHEST POSITION NONE. 2D AND 1B MODE REPLY21AA051AC20 AGCQJ 04RADIUS,TURN,VEHICULAR VEHICULAR TURN RADIUS THE RADIUS OF A CIRCLE FORMED BY THE OUTERMOST PART OF A VEHICLE WHILE EXECUTING THE SHORTEST POSSIBLE TURN. 2D AND 1B MODE REPLY21AA051AC20 AGCRJ 04WIDTH,MINIMUM,STORAGE AISLE STORAGE AISLE MINIMUM WIDTH THE MINIMUM DISTANCE REQUIRED BETWEEN PALLETS,PLATFORMS,AND THE LIKE /STORAGE AISLE WIDTH/,TO PERFORM RIGHT ANGLE STACKING AND/OR TIERING FUNCTIONS. 1D AND 1B MODE REPLY11AA05 AGCSJ /D/ 10LOAD RATING,MAXIMUM MAXIMUM LOAD RATING THE MAXIMUM LOAD FOR WHICH THE ITEM IS RATED. PLEASE USE MRC AYXK IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1B MODE REPLY12AB16 AGCTJ 04DISTANCE,CENTER,FORK LOAD FORK LOAD CENTER DISTANCE A MEASUREMENT OF THE DISTANCE FROM THE FRONT FACE OF THE FORKS TO A SPECIFIED POINT AT WHICH THE RATED LOAD CAPACITY IS DETERMINED. 2D AND 1B MODE REPLY21AA051AC20 AGCUD /D/ 18TYPE,MAST,FORK/PLATFORM FORK/PLATFORM MAST TYPE INDICATES THE TYPE OF MAST (BOOM) ON WHICH THE FORKS OR PLATFORMS ARE OPERATED. SELECT REPLY CODE 10AE80 AGCVD /D/ 07FEATURE,MAST,TELESCOPIC TELESCOPIC MAST FEATURE AN INDICATION OF WHETHER OR NOT THE MAST HAS A TELESCOPIC FEATURE INCLUDED. SELECT REPLY CODE 10AA49 AGCWJ 04DIAMETER,WIRE WIRE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WIRE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGCXJ 04WIDTH,TAPE TAPE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TAPE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AGCYJ 04DIAMETER,HOLE,SPINDLE SPINDLE HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SPINDLE HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGCZJ 04DIAMETER,OUTSIDE,REEL REEL OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A REEL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGDAJ 04WIDTH,REEL REEL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A REEL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AGDBJ 04HEIGHT,FREE LIFT,MAXIMUM,FORK/PLATFORM FORK/PLATFORM MAXIMUM FREE LIFT HEIGHT THE MAXIMUM VERTICAL HEIGHT OR DISTANCE THE CARRYING SURFACE OF THE FORKS,PLATFORM,AND THE LIKE,CAN BE RAISED FROM GROUND LEVEL WITHOUT EXTENDING THE UPRIGHTS BEYOND THE SPECIFIED COLLAPSE MAST HEIGHT. 1D AND 1B MODE REPLY11AA05 AGDCD /D/ 18TYPE,MECHANISM,LIFT LIFT MECHANISM TYPE INDICATES THE TYPE OF LIFT MECHANISM INCLUDED ON THE ITEM. SELECT REPLY CODE 10AD49 AGDDD /D/ 11METHOD,ACTUATION,LIFT LIFT ACTUATION METHOD THE MEANS BY WHICH THE LIFT IS ACTUATED. SELECT REPLY CODE 10AA77 AGDEJ 04HEIGHT,SURFACE,LOAD CARRYING,MINIMUM MINIMUM LOAD CARRYING SURFACE HEIGHT THE DISTANCE MEASURED FROM THE GROUND/FLOOR SURFACE TO THE LOAD CARRYING SURFACE IN THE LOWEST POSITION. 1D AND 1B MODE REPLY11AA05 AGDFJ /D/ 04DISTANCE,MINIMUM,FORK SPREAD FORK SPREAD MINIMUM DISTANCE THE MINIMUM OUTSIDE TO OUTSIDE DISTANCE BETWEEN FORKS. 1D AND 1B MODE REPLY11AA05 AGDGJ /D/ 04DISTANCE,MAXIMUM,FORK SPREAD FORK SPREAD MAXIMUM DISTANCE THE MAXIMUM OUTSIDE TO OUTSIDE DISTANCE BETWEEN FORKS. 1D AND 1B MODE REPLY11AA05 AGDHA 12QUANTITY,WHEEL WHEEL QUANTITY THE NUMBER OF WHEELS INCLUDED ON THE ITEM. 1A MODE REPLY 0 AGDJA 12QUANTITY,WHEEL,DRIVE DRIVE WHEEL QUANTITY THE NUMBER OF DRIVE WHEELS INCLUDED ON THE ITEM. 1A MODE REPLY 0 AGDKJ /D/ 04DISTANCE BETWEEN HOLES ALONG LENGTH,CENTER TO CENTER,END,FIFTH FIFTH END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGDLJ /D/ 04DISTANCE BETWEEN HOLES ALONG WIDTH,CENTER TO CENTER,END,FIFTH FIFTH END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGDMD /D/ 18TYPE,TIRE,DRIVE WHEEL DRIVE WHEEL TIRE TYPE INDICATES THE TYPE OF DRIVE WHEEL TIRES ON THE ITEM. SELECT REPLY CODE 10AE82 AGDNA /D/ 12QUANTITY,WHEEL,LOAD LOAD WHEEL QUANTITY THE NUMBER OF LOAD WHEELS PROVIDED ON THE ITEM. 1A MODE REPLY 0 AGDPD 18TYPE,TIRE,LOAD WHEEL LOAD WHEEL TIRE TYPE INDICATES THE TYPE OF LOAD WHEEL TIRES PROVIDED ON THE ITEM. SELECT REPLY CODE 10AE82 AGDQA 12QUANTITY,WHEEL,STEERABLE STEERABLE WHEEL QUANTITY THE NUMBER OF STEERABLE WHEELS INCLUDED ON THE ITEM. 1A MODE REPLY 0 AGDRD /D/ 18TYPE,TIRE,STEERABLE WHEEL STEERABLE WHEEL TIRE TYPE INDICATES THE TYPE OF STEERABLE WHEEL TIRES PROVIDED ON THE ITEM. SELECT REPLY CODE 10AE82 AGDSD 18TYPE,STEERING STEERING TYPE INDICATES THE TYPE OF STEERING MECHANISM PROVIDED ON THE ITEM. SELECT REPLY CODE 10AE83 AGDTD /D/ 19FEATURE,DIRECTING,LAMP ILLUMINATION LAMP ILLUMINATION DIRECTING FEATURE THE SPECIFIC PORTION OR MEANS USED FOR DIRECTING THE TRANSMITTED LIGHT. SELECT REPLY CODE 10AE84 AGDUD /D/ 07FEATURE,WATERPROOF WATERPROOF FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM IS WATERPROOF. SELECT REPLY CODE 10AA89 AGDVD 19CHARACTERISTIC,LIGHT,EMITTED EMITTED LIGHT CHARACTERISTIC THE CHARACTERISTIC OF THE RADIANT ENERGY GENERATED BY THE LAMP WITHIN OR ADJACENT TO THE VISIBLE SPECTRUM OF LIGHT. SELECT REPLY CODE 10AD06 AGDWJ 04LENGTH,CENTER,LIGHT LIGHT CENTER LENGTH THE DISTANCE FROM THE GEOMETRIC CENTER OF THE LIGHT SOURCE TO A PARTICULAR POINT ON THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 AGDXD /D/ 18TYPE,TRANSMISSION TRANSMISSION TYPE INDICATES THE TYPE OF TRANSMISSION USED TO TRANSFER THE DEVELOPED MECHANICAL ENERGY FROM THE ENGINE (MOTOR/PRIME MOVER) TO THE DRIVE UNIT OR DIFFERENTIAL. SELECT REPLY CODE 10AA77 AGDYD /D/ 07SHIFT,SIDE,FORK FORK SIDE SHIFT AN INDICATION OF WHETHER OR NOT A MECHANISM DESIGNED TO MOVE THE FORKS HORIZONTALLY TO THE RIGHT OR LEFT SIDE OF THE LIFT CARRIAGE IS INCLUDED. SELECT REPLY CODE 10AA49 AGDZD /D/ 07DEVICE,LEVELING,LOAD LOAD LEVELING DEVICE AN INDICATION OF WHETHER OR NOT AN INDEPENDENTLY OPERATED DEVICE DESIGNED TO COMPENSATE FOR IRREGULAR SURFACE CONDITIONS IS INCLUDED. SELECT REPLY CODE 10AA49 AGEAG /D/ 19CODE AND MODEL NUMBER,MANUFACTURER,ENGINE/MOTOR ENGINE/MOTOR MANUFACTURER CODE AND MODEL NUMBER THE FIVE-POSITION CODE WHICH REPRESENTS THE MANUFACTURER OF THE ENGINE/MOTOR (PRIME MOVER) FURNISHED WITH THE ITEM AND THE MODEL NUMBER. PLEASE USE MRC AMWN AND AZYA IN PLACE OF THIS DISCONTINUED MRC. FULL TEXT WRITE-IN 0 AGEBD /D/ 07FEATURE,FORDING FORDING FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE IS INCLUDED FOR THE ITEM TO BE OPERATED IN A SPECIFIED DEPTH OF WATER WITHOUT MALFUNCTION. SELECT REPLY CODE 10AA49 AGECD /D/ 19SIZE,TIRE TIRE SIZE DESIGNATES THE SIZE BY WHICH THE TIRE IS COMMERCIALLY KNOWN AND DESIGNATED. SELECT REPLY CODE 10AA27 AGEDJ /D/ 10WIDTH,PULSE PULSE WIDTH THE DURATION OF THE FORMED PULSE. 2D AND 1B MODE REPLY22AH681AC20 AGEEJ /D/ 10TIME,RISE,PULSE PULSE RISE TIME THE RATE AT WHICH THE PULSE REACHES ITS PEAK. 2D AND 1B MODE REPLY22AH681AC20 AGEFD /D/ 07STEERING,POWER POWER STEERING AN INDICATION OF WHETHER OR NOT A POWER ASSISTED STEERING MECHANISM IS INCLUDED IN THE ITEM. SELECT REPLY CODE 10AA49 AGEGJ /D/ 04DISTANCE W/O LOAD,SURFACE LEVEL TO HORIZONTAL CENTER OF GRAVITY SURFACE LEVEL TO HORIZONTAL CENTER OF GRAVITY DISTANCE W/O LOAD A MEASUREMENT FROM THE SURFACE LEVEL TO THE HORIZONTAL CENTER OF GRAVITY OF THE ITEM WITHOUT LOAD. 2D AND 1B MODE REPLY21AA051AC20 AGEHJ /D/ 04DISTANCE W/O LOAD,FORK FACE TO VERTICAL CENTER OF GRAVITY FORK FACE TO VERTICAL CENTER OF GRAVITY DISTANCE W/O LOAD A MEASUREMENT FROM THE FACE OF THE FORK TO THE VERTICAL CENTER OF GRAVITY OF THE ITEM WITHOUT LOAD. 2D AND 1B MODE REPLY21AA051AC20 AGEJD 19SYSTEM FOR WHICH DESIGNED SYSTEM FOR WHICH DESIGNED INDICATES THE TYPE OF SYSTEM IN WHICH THE ITEM IS DESIGNED TO BE USED. SELECT REPLY CODE 10AE81 AGEKJ 04LENGTH,FREE,SPRING SPRING FREE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGELJ /D/ 04DIAMETER,CIRCLE,CAM INSIDE CAM INSIDE CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGEMJ /D/ 04DIAMETER,CIRCLE,CAM OUTSIDE CAM OUTSIDE CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGENJ 04WIDTH,CAM CAM WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CAM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AGEPJ /D/ 04DIAMETER,OPENING,FREE FREE OPENING DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGEQJ /D/ 04DIAMETER,INSIDE,PILOT BARREL PILOT BARREL INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGERJ /D/ 04DIAMETER,OUTSIDE,PILOT BARREL PILOT BARREL OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGESJ 04HEIGHT,HANDLE HANDLE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AGETJ 04LENGTH,SEALING SEALING LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGEUJ 04DIAMETER,BASE BASE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR BASE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGEVJ /D/ 04LENGTH,BARREL,PILOT PILOT BARREL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGEWJ /D/ 04THICKNESS,CAM CAM THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGEXA 12QUANTITY,CAM CAM QUANTITY THE NUMBER OF CAMS INCLUDED ON THE ITEM. 1A MODE REPLY 0 AGEYD /D/ 11METHOD,ACTUATION,CAP SAFETY VENT CAP SAFETY VENT ACTUATION METHOD THE MEANS USED TO ACTUATE A DEVICE INCORPORATED IN THE CAP TO RELIEVE PRESSURE IN EXCESS OF THE MAXIMUM OPERATING PRESSURE OR TO BLEED OFF ALL INTERNAL PRESSURE PRIOR TO REMOVAL FROM THE FILLER OPENING. SELECT REPLY CODE 10AA77 AGEZD 18TYPE,DEVICE,RETAINING RETAINING DEVICE TYPE INDICATES THE TYPE OF RETAINING DEVICE USED TO SAFEGUARD THE ITEM AGAINST LOSS. SELECT REPLY CODE 10AC52 AGFAJ 04LENGTH,CHAIN CHAIN LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CHAIN. 2D AND 1B MODE REPLY21AA051AC20 AGFBD /D/ 07VENT VENT AN INDICATION OF WHETHER OR NOT A VENT IS INCLUDED. SELECT REPLY CODE 10AA49 AGFCD /D/ 07GASKET GASKET AN INDICATION OF WHETHER OR NOT A GASKET IS INCLUDED. SELECT REPLY CODE 10AA49 AGFDJ /D/T13THREAD PITCH DIAMETERS,HOLE,MOUNTING MOUNTING HOLE THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A MOUNTING HOLE STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 AGFED /D/ 08LOCATION,HARDNESS,METALLIC METALLIC HARDNESS LOCATION INDICATES THE LOCATION OF THE ITEM TO WHICH THE METALLIC HARDNESS IS APPLIED. SELECT REPLY CODE 10AE46 AGFFJ 04WIDTH,FLANGE FLANGE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A FLANGE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AGFGJ /D/ 04DISTANCE,END TO FLANGE END TO FLANGE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AGFHJ 04DIAMETER,HOLE,LEFT INTERNAL FLANGE LEFT INTERNAL FLANGE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGFJJ 04DIAMETER,HOLE,RIGHT INTERNAL FLANGE RIGHT INTERNAL FLANGE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGFKJ 04WIDTH,FLANGE,LEFT INTERNAL LEFT INTERNAL FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGFLJ 04WIDTH,FLANGE,RIGHT INTERNAL RIGHT INTERNAL FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGFMJ 04DISTANCE,END OF ROUNDED EXTENSION TO RIGHT END OF BEARING END OF ROUNDED EXTENSION TO RIGHT END OF BEARING DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AGFNJ 04DISTANCE,END OF ROUNDED EXTENSION OF V GROOVE TO BOTTOM OF V GROOVE END OF ROUNDED EXTENSION OF V GROOVE TO BOTTOM OF V GROOVE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AGFPJ 04RADIUS,EXTENSION,ROUNDED,V GROOVE V GROOVE ROUNDED EXTENSION RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGFQJ 04DIAMETER,OUTSIDE,LEFT FLANGE LEFT FLANGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGFRJ 04DIAMETER,OUTSIDE,RIGHT FLANGE RIGHT FLANGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGFSJ 04WIDTH,FLANGE,LEFT LEFT FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGFTJ 04WIDTH,FLANGE,RIGHT RIGHT FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGFUJ 04DIAMETER,HOLE,INTERIOR FLANGE INTERIOR FLANGE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGFVJ 04DISTANCE,INTERIOR FLANGE LEFT END TO CENTERLINE INTERIOR FLANGE LEFT END TO CENTERLINE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AGFWJ 04WIDTH,FLANGE,INTERIOR INTERIOR FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGFXJ 04DIAMETER,OUTSIDE,EXTENSION EXTENSION OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGFYJ /D/ 04DIAMETER,OUTSIDE,SPHERICAL SPHERICAL OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGFZJ 04DIAMETER,BODY,SPHERICAL SPHERICAL BODY DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGGAD 05DIRECTION,MOVEMENT,STEM STEM MOVEMENT DIRECTION THE DIRECTION IN WHICH THE STEM IS MOVING WHEN OPENING THE VALVE. SELECT REPLY CODE 10AE85 AGGBJ /D/ 04RADIUS,CORNER,KEY KEY CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGGCJ 04RADIUS,KEY KEY RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGGDJ /D/ 04RADIUS,CORNER,FLATS FLATS CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGGEJ /D/ 04RADIUS,CORNER,KEY BOTTOM KEY BOTTOM CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGGFJ 04DIAMETER,OUTSIDE,OUTER MEMBER OUTER MEMBER OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGGGJ 04DISTANCE,BORE CENTER TO SHANK END BORE CENTER TO SHANK END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AGGHJ 04WIDTH,MEMBER,OUTER OUTER MEMBER WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGGJJ 04WIDTH,MEMBER,INNER INNER MEMBER WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGGKJ /D/ 04DIAMETER,FLATS,BALL BALL FLATS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGGLJ 04LENGTH,SHANK END TO SHOULDER SHANK END TO SHOULDER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGGMJ /D/ 04DIAMETER,BEGINNING,TAPER TAPER BEGINNING DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGGNJ 04DIAMETER,END,TAPER TAPER END DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGGPJ 04DIAMETER,HOLE,DRILLED DRILLED HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A DRILLED HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGGQJ 04DEPTH,HOLE,DRILLED DRILLED HOLE DEPTH AN INSIDE MEASUREMENT FROM THE TOP TO THE BOTTOM OF THE DRILLED HOLE,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AGGRJ 04WIDTH,GROOVE,V V GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGGSB 04ANGLE IN DEG,GROOVE,V V GROOVE ANGLE IN DEG THE ANGLE OF THE V GROOVE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AGGTB /D/ 04ANGLE IN DEG,CHAMFER,KEY CORNER KEY CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AGGUJ /D/ 04RADIUS,CORNER,KEYWAY KEYWAY CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGGVB /D/ 04ANGLE IN DEG,CHAMFER,KEYWAY CORNER KEYWAY CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AGGWJ 04RADIUS,KEYWAY KEYWAY RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGGXA /D/ 16STYLE,SHANK,BEARING BEARING SHANK STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BEARING SHANK. 1A MODE REPLY 0 AGGYJ 04THREAD LENGTH,SHANK SHANK THREAD LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGGZJ 04DIAMETER,OUTSIDE,SHANK SHANK OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SHANK,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGHAJ 04DISTANCE,INSPECTION HOLE CENTER TO END INSPECTION HOLE CENTER TO END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AGHBJ 04WIDTH ACROSS WRENCH FLATS,SHANK SHANK WIDTH ACROSS WRENCH FLATS THE SHORTEST STRAIGHT LINE BETWEEN WRENCHING FLATS,PERPENDICULAR TO THE HEIGHT OF THE SHANK. 2D AND 1B MODE REPLY21AA051AC20 AGHCJ 04DIAMETER,INSIDE,SHANK SHANK INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGHDJ 04LENGTH,HOLE,SHANK SHANK HOLE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGHEH /D/ 19CONFIGURATION,CORNER CORNER CONFIGURATION AN INDICATION OF THE PREFORMED SHAPE OF THE EDGE/S/ AND ITS LOCATION ON THE ITEM. 2D MODE REPLY 22AE462AE88 AGHFJ 04DISTANCE BETWEEN MOUNTING HOLES ALONG HEIGHT,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES ALONG HEIGHT NONE. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 2D AND 1B MODE REPLY21AA051AC20 AGHGJ 04DEPTH,CHAMFER CHAMFER DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGHHJ /D/ 04WIDTH,CORNER CORNER WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGHJJ /D/ 04RADIUS,CORNER,OUTSIDE,FIRST FIRST OUTSIDE CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGHKJ /D/ 04RADIUS,CORNER,OUTSIDE,SECOND SECOND OUTSIDE CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGHLJ /D/ 04RADIUS,CORNER,OUTSIDE,THIRD THIRD OUTSIDE CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGHMJ /D/ 04RADIUS,CORNER,OUTSIDE,FOURTH FOURTH OUTSIDE CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGHNJ /D/ 04RADIUS,CORNER,INSIDE,FIRST FIRST INSIDE CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGHPJ /D/ 04RADIUS,CORNER,INSIDE,SECOND SECOND INSIDE CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGHQJ /D/ 04RADIUS,CORNER,INSIDE,THIRD THIRD INSIDE CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGHRJ /D/ 04RADIUS,CORNER,INSIDE,FOURTH FOURTH INSIDE CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGHSJ 04RADIUS,SPHERICAL,OUTSIDE OUTSIDE SPHERICAL RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGHTJ 04RADIUS,SPHERICAL,INSIDE INSIDE SPHERICAL RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGHUJ /D/ 10TIME,FALL,PULSE PULSE FALL TIME THE RATE AT WHICH THE PULSE DECREASES ITS PEAK. 2D AND 1B MODE REPLY22AH681AC20 AGHVJ 04RADIUS,OUTSIDE,CURVATURE CURVATURE OUTSIDE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGHWJ 04RADIUS,INSIDE,CURVATURE CURVATURE INSIDE RADIUS A MEASUREMENT OF A LINE SEGMENT EXTENDING FROM THE CENTER OF A CURVATURE PORTION TO THE INSIDE SURFACE. 2D AND 1B MODE REPLY21AA051AC20 AGHXJ 04DEPTH,SPHERICAL SPHERICAL DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGHYB /D/ 04ANGLE IN DEG,CHAMFER,FIRST OUTSIDE CORNER FIRST OUTSIDE CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AGHZB /D/ 04ANGLE IN DEG,CHAMFER,SECOND OUTSIDE CORNER SECOND OUTSIDE CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AGJAB /D/ 04ANGLE IN DEG,CHAMFER,THIRD OUTSIDE CORNER THIRD OUTSIDE CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AGJBB /D/ 04ANGLE IN DEG,CHAMFER,FOURTH OUTSIDE CORNER FOURTH OUTSIDE CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AGJCB /D/ 04ANGLE IN DEG,CHAMFER,FIRST INSIDE CORNER FIRST INSIDE CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AGJDB /D/ 04ANGLE IN DEG,CHAMFER,SECOND INSIDE CORNER SECOND INSIDE CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AGJEB /D/ 04ANGLE IN DEG,CHAMFER,THIRD INSIDE CORNER THIRD INSIDE CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AGJFB /D/ 04ANGLE IN DEG,CHAMFER,FOURTH INSIDE CORNER FOURTH INSIDE CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AGJGB /D/ 04ANGLE IN DEG,CHAMFER,SPHERICAL,INSIDE INSIDE SPHERICAL CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AGJHJ 04WIDTH ACROSS FLATS,HOLE,CENTER CENTER HOLE WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGJJJ /D/ 04RADIUS,CORNER,CENTER HOLE FLATS CENTER HOLE FLATS CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGJKJ 04WIDTH,KEY,CENTER HOLE CENTER HOLE KEY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGJLJ 04LENGTH,KEY,CENTER HOLE CENTER HOLE KEY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGJMJ 04DEPTH,KEYWAY,CENTER HOLE CENTER HOLE KEYWAY DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGJNJ /D/ 04RADIUS,CORNER,CENTER HOLE KEY CENTER HOLE KEY CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGJPJ 04RADIUS,BOTTOM,CENTER HOLE KEY CENTER HOLE KEY BOTTOM RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGJQJ /D/ 04RADIUS,KEY,CENTER HOLE CENTER HOLE KEY RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGJRJ 04DIAMETER,MINOR MINOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST DIAMETER OF THE ITEM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGJSJ 04DIAMETER,PITCH PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER SPECIFIC MEASUREMENT SCALE OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 AGJTJ 04WIDTH,KEYWAY,CENTER HOLE CENTER HOLE KEYWAY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGJUJ /D/ 04RADIUS,CORNER,CENTER HOLE KEYWAY CENTER HOLE KEYWAY CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGJVB /D/ 04ANGLE IN DEG,CHAMFER,CENTER HOLE KEY CORNER CENTER HOLE KEY CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AGJWB /D/ 04ANGLE IN DEG,CHAMFER,CENTER HOLE KEYWAY CORNER CENTER HOLE KEYWAY CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AGJXJ /D/ 04RADIUS,BOTTOM,CENTER HOLE KEYWAY CENTER HOLE KEYWAY BOTTOM RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGJYJ 04RADIUS,KEYWAY,CENTER HOLE CENTER HOLE KEYWAY RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGJZA 12QUANTITY,KEY,CENTER HOLE CENTER HOLE KEY QUANTITY THE NUMBER OF KEYS CONTAINED IN THE CENTER HOLE OF THE ITEM. 1A MODE REPLY 0 AGKAA 12QUANTITY,KEYWAY,CENTER HOLE CENTER HOLE KEYWAY QUANTITY THE NUMBER OF KEYWAYS CONTAINED IN THE CENTER HOLE OF THE ITEM. 1A MODE REPLY 0 AGKBA /D/ 12QUANTITY,HOLE,ANTIROTATION/LUBRICATION ANTIROTATION/LUBRICATION HOLE QUANTITY THE NUMBER OF HOLES USED AS AN ANTIROTATIONAL DEVICE OR FOR THE INTRODUCTION OF A LUBRICANT. 1A MODE REPLY 0 AGKCA /D/ 12QUANTITY,SLOT,ANTIROTATION/LUBRICATION ANTIROTATION/LUBRICATION SLOT QUANTITY THE NUMBER OF SLOTS USED AS AN ANTIROTATIONAL DEVICE OR FOR THE INTRODUCTION OF A LUBRICANT. 1A MODE REPLY 0 AGKDJ 04DISTANCE FROM CENTERLINE OF OPENING TO LEFT END OF BEARING DISTANCE FROM CENTERLINE OF OPENING TO LEFT END OF BEARING THE DISTANCE,MEASURED ALONG A STRAIGHT LINE PARALLEL TO THE LONGITUDINAL AXIS OF THE BEARING,FROM THE CENTER OF THE APERTURE TO THE LEFT END OF THE BEARING. 2D AND 1B MODE REPLY21AA051AC20 AGKFD /D/ 08LOCATION,KEYWAY KEYWAY LOCATION INDICATES THE LOCATION OF THE KEYWAY IN THE ITEM. SELECT REPLY CODE 10AE46 AGKGJ /D/A19FINISH AND LOCATION,SURFACE SURFACE FINISH AND LOCATION DESIGNATES THE SPECIFIC SURFACE ROUGHNESS RATING REPRESENTING THE ARITHMETIC AVERAGE DEVIATION OF THE SURFACE FROM THE MEANLINE IN A PROFILE /THE ARITHMETIC AVERAGE AMOUNT OF DEVIATION OF PEAKS AND VALLEYS FROM A MEANLINE/ AND ITS LOCATION ON AN ITEM. 2D AND 1A MODE REPLY21AE862AE46 AGKHL 16STYLE,ACCOMMODATION,LUBRICANT LUBRICANT ACCOMMODATION STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE MEANS WHEREBY THE LUBRICANT IS SET INTO THE ITEM. 1L MODE REPLY 0 AGKJA /D/ 12QUANTITY,GROOVE,SURFACE SURFACE GROOVE QUANTITY THE NUMBER OF GROOVES LOCATED ON THE SURFACE OF THE ITEM. 1A MODE REPLY 0 AGKKD /D/ 08LOCATION,GROOVE GROOVE LOCATION INDICATES THE LOCATION OF THE GROOVE(S) ON THE ITEM. SELECT REPLY CODE 10AE46 AGKLD 18TYPE,FITTING,LUBRICATION LUBRICATION FITTING TYPE INDICATES THE TYPE OF FITTING USED TO LUBRICATE THE ITEM. SELECT REPLY CODE 10AE87 AGKMJ /D/ 04DIAMETER,RESERVOIR,LUBRICATION LUBRICATION RESERVOIR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LUBRICATION RESERVOIR,AND TERMINATES AT THE CIRCUMFERENCE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 2D AND 1B MODE REPLY21AA051AC20 AGKND /D/ 07FITTING,CLOSURE,SCREW PLUG SCREW PLUG CLOSURE FITTING AN INDICATION OF WHETHER OR NOT A THREADED PLUG WHICH PREVENTS LEAKAGE OF THE LUBRICANT IS INCLUDED. SELECT REPLY CODE 10AA49 AGKPJ A10LOAD RATING,RADIAL,STATIC STATIC RADIAL LOAD RATING THE LIMITING RADIAL LOAD WHICH THE ITEM CAN CARRY AT REST WITHOUT PERMANENT DEFORMATION OF THE STRESSED SURFACE OR THE DANGER OF FRACTURE. 1D AND 1A MODE REPLY12AB16 AGKQA 12QUANTITY,HOLE,BEARING SURFACE BEARING SURFACE HOLE QUANTITY THE NUMBER OF HOLES IN THE BEARING SURFACE EXCLUDING THE CENTER HOLE. 1A MODE REPLY 0 AGKRJ 04DIAMETER,HOLE,BEARING SURFACE BEARING SURFACE HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BEARING SURFACE HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGKSJ /D/ 04DISTANCE BETWEEN HOLES ALONG BOLT CIRCLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG BOLT CIRCLE THE CENTER TO CENTER DISTANCE BETWEEN HOLES EQUALLY SPACED AROUND A BOLT CIRCLE DIAMETER. 2D AND 1B MODE REPLY21AA051AC20 AGKTJ 04HEIGHT,LUG,LOCKING LOCKING LUG HEIGHT A MEASUREMENT FROM THE OUTER SURFACE OF AN ITEM TO THE OUTERMOST POINT OF THE LOCKING LUG. 2D AND 1B MODE REPLY21AA051AC20 AGKUJ 04LENGTH,LUG,LOCKING LOCKING LUG LENGTH THE DISTANCE,MEASURED ALONG A STRAIGHT LINE PARALLEL TO THE LONGITUDINAL AXIS OF THE LUG,FROM ONE EDGE TO THE OTHER. 2D AND 1B MODE REPLY21AA051AC20 AGKVJ 04WIDTH,LUG,LOCKING LOCKING LUG WIDTH THE DISTANCE,MEASURED ALONG A STRAIGHT LINE,PERPENDICULAR TO THE LONGITUDINAL AXIS OF THE LUG,FROM ONE EDGE TO THE OTHER. 2D AND 1B MODE REPLY21AA051AC20 AGKWJ /D/ 04DISTANCE FROM CENTERLINE OF LUG TO LEFT END OF BEARING DISTANCE FROM CENTERLINE OF LUG TO LEFT END OF BEARING THE DISTANCE,MEASURED ALONG A STRAIGHT LINE PARALLEL TO THE LONGITUDINAL AXIS OF THE BEARING,FROM THE CENTER OF THE LUG TO THE LEFT END OF THE BEARING. 2D AND 1B MODE REPLY21AA051AC20 AGKXG 19ITEM,SUPPLY SUPPLY ITEM A MAJOR COMPONENT WHICH IS COMPRISED OF A NATIONAL STOCK NUMBER AND THE ITEM NAME,STANDARDIZED NAME,OR PART NAME. FULL TEXT WRITE-IN 0 AGKYG 19ITEM,NONSUPPLY NONSUPPLY ITEM A MAJOR COMPONENT,OUTSIDE THE SCOPE OF AN ITEM OF SUPPLY TO BE CATALOGED,AS INDICATED BY THE NAME OF THE MANUFACTURER AND THE NAME AND NUMBER OF THE ITEM AS IDENTIFIED BY THE MANUFACTURER. FULL TEXT WRITE-IN 0 AGKZA /D/ 12QUANTITY,PACKAGE,INTERMEDIATE INTERMEDIATE PACKAGE QUANTITY THE NUMBER OF INTERIOR CONTAINERS,EACH OF WHICH CONTAINS TWO OR MORE UNIT PACKAGES OF IDENTICAL ITEMS. 1A MODE REPLY 0 AGLAA /D/ 10LIFE IN MONTHS,SHELF SHELF LIFE IN MONTHS THE TIME IN WHICH THE ITEM HAS CERTAIN PHYSICAL AND MATERIAL CHARACTERISTICS THAT LIMITS ITS STORAGE OR SHELF LIFE,EXPRESSED IN MONTHS. 1A MODE REPLY 0 AGLBJ /D/ 10WEIGHT,GROSS,UNIT PACKAGE UNIT PACKAGE GROSS WEIGHT THE COMBINED WEIGHT OF THE CONTAINER AND CONTENTS INCLUDING PACKAGING MATERIAL WHICH IS PART OF THE UNIT. 1D AND 1B MODE REPLY11AB18 AGLCB /D/ 04ANGLE IN DEG,SPACING,HOLE HOLE SPACING ANGLE IN DEG THE ANGLE FORMED BY THE CENTERLINE OF TWO HOLES NOT IN THE SAME PLANE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AGLDD 18TYPE,PERFORMANCE PERFORMANCE TYPE INDICATES THE PERFORMANCE CAPABILITY OF THE ITEM OR COMPONENT. SELECT REPLY CODE 10AE89 AGLED 19CONTOUR,PERIPHERAL PERIPHERAL CONTOUR THE GEOMETRIC CONFIGURATION WHICH IS THE PERIPHERAL CONTOUR OF THE ITEM. SELECT REPLY CODE 10AC46 AGLFJ 04RADIUS,CURVE,INTERLOCKING CHAIN INTERLOCKING CHAIN CURVE RADIUS THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE CENTER TO THE PERIPHERY OF THE CIRCLE FORMED BY THE CURVE PASSING THROUGH THE CENTER OF THE CHAIN. 2D AND 1B MODE REPLY21AA051AC20 AGLGD /D/ 07FEATURE,SEALING SEALING FEATURE AN INDICATION OF WHETHER OR NOT A WATER TIGHT AND PRESSURE SEALING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AGLHD /D/ 05DIRECTION,SEPARATION SEPARATION DIRECTION AN INDICATION OF THE DIRECTION OF SEPARATION IN WHICH THE ITEM IS DESIGNED TO OPERATE. SELECT REPLY CODE 10AA38 AGLJD 18TYPE,RELEASE RELEASE TYPE INDICATES THE TYPE OF RELEASE INCORPORATED IN THE ITEM. SELECT REPLY CODE 10AE90 AGLKD 18TYPE,STOP STOP TYPE INDICATES THE TYPE OF STOP INCORPORATED IN THE ITEM. SELECT REPLY CODE 10AE91 AGLLD /D/ 08LOCATION,STOP STOP LOCATION THE DESIGNATION OF THAT PART OF THE ITEM TO WHICH THE STOP IS LOCATED. SELECT REPLY CODE 10AE46 AGLMA 12QUANTITY,SLIDER SLIDER QUANTITY THE NUMBER OF SLIDERS FURNISHED. 1A MODE REPLY 0 AGLND 07REVERSIBILITY,SLIDER SLIDER REVERSIBILITY AN INDICATION OF WHETHER OR NOT THE SLIDER IS REVERSIBLE. SELECT REPLY CODE 10AF62 AGLPA 12QUANTITY,PULL,SLIDER SLIDER PULL QUANTITY THE NUMBER OF SLIDER PULLS ATTACHED TO THE SLIDER. 1A MODE REPLY 0 AGLQD 18TYPE,PULL,SLIDER SLIDER PULL TYPE INDICATES THE TYPE OF SLIDER PULL PROVIDED ON THE ITEM. SELECT REPLY CODE 10AE93 AGLRJ 04LENGTH,EXTENSION,FASTENER TAPE FASTENER TAPE EXTENSION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FASTENER TAPE EXTENDING BEYOND THE SCOOPS OR STOPS. 2D AND 1B MODE REPLY21AA051AC20 AGLSB 10RATE IN HERTZ,REFRESH,IMAGE IMAGE REFRESH RATE IN HERTZ AN INDICATION OF HOW OFTEN THE IMAGE IS REFRESHED PER SECOND. 1B MODE REPLY 0 AGLTD /D/ 19PROTECTION,ENVIRONMENTAL,TAPE TAPE ENVIRONMENTAL PROTECTION THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT THE TAPE IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY. SELECT REPLY CODE 10AA65 AGLUL 16STYLE,BARREL BARREL STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BARREL. 1L MODE REPLY 0 AGLVJ 04DIAMETER,OUTSIDE,BARREL BARREL OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGLWJ 04DIAMETER,OUTSIDE,LARGEST,BARREL BARREL LARGEST OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGLXJ 04LENGTH,BARREL BARREL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BARREL,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AGLYJ 04WIDTH,BARREL BARREL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGLZJ 04HEIGHT,OVERALL,BARREL BARREL OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AGMAJ /D/ 04DIAMETER,OUTSIDE,BARREL FLANGE BARREL FLANGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGMBJ 04LENGTH,LARGEST,BARREL BARREL LARGEST LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGMCJ 04WIDTH,LARGEST,BARREL BARREL LARGEST WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGMDA /D/ 16STYLE,FLANGE FLANGE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FLANGE. 1A MODE REPLY 0 AGMEL 16STYLE,GROMMET GROMMET STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE GROMMET. 1L MODE REPLY 0 AGMFJ 04DIAMETER,OUTSIDE,LARGE FLANGE LARGE FLANGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGMGJ 04DIAMETER,OUTSIDE,SMALL FLANGE SMALL FLANGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGMHJ 04DIAMETER,OUTSIDE,GROOVE GROOVE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGMJB 04ANGLE IN DEG,HOLE HOLE ANGLE IN DEG NONE. 1B MODE REPLY 0 AGMKJ 04LENGTH,HOLE HOLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A HOLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AGMLJ 04DIAMETER,HOLE,THIRD THIRD HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGMMJ 04DIAMETER,HOLE,FOURTH FOURTH HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGMNJ 04RADIUS,FLANGE,LARGE LARGE FLANGE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGMPJ 04RADIUS,FLANGE,SMALL SMALL FLANGE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGMQJ 04DIAMETER,HOLE,LARGE END LARGE END HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGMRJ 04DIAMETER,HOLE,SMALL END SMALL END HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGMSJ 04LENGTH,HOLE CENTER TO FLAT END HOLE CENTER TO FLAT END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGMTJ 04WIDTH BETWEEN TABS WIDTH BETWEEN TABS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGMUD /D/ 18TYPE,CONSTRUCTION,GROMMET GROMMET CONSTRUCTION TYPE INDICATES THE TYPE OF DESIGN USED IN CONSTRUCTING THE GROMMET. SELECT REPLY CODE 10AC40 AGMVL 16STYLE,EYELET EYELET STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE EYELET. 1L MODE REPLY 0 AGMWD /D/ 07FEATURE,RESISTANT,OIL AND COOLANT OIL AND COOLANT RESISTANT FEATURE AN INDICATION OF WHETHER OR NOT AN OIL AND COOLANT RESISTANT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AGMXL 16STYLE,STUD,SNAP FASTENER SNAP FASTENER STUD STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SNAP FASTENER STUD. 1L MODE REPLY 0 AGMYJ 04LENGTH,SHANK,STUD STUD SHANK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGMZJ 04LENGTH,OVERALL,STUD STUD OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE STUD. 2D AND 1B MODE REPLY21AA051AC20 AGNAJ 04DIAMETER,HEAD,STUD STUD HEAD DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGNBJ 04DIAMETER,SHANK,STUD STUD SHANK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGNCJ 04DIAMETER,BASE,STUD STUD BASE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGNDJ 04WIDTH ACROSS FLATS,BASE,STUD STUD BASE WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGNEJ 04LENGTH,PRONG,STUD STUD PRONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGNFJ 04LENGTH,BASE BASE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BASE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AGNGL 16STYLE,SOCKET,SNAP FASTENER SNAP FASTENER SOCKET STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SNAP FASTENER SOCKET. 1L MODE REPLY 0 AGNHJ 04HEIGHT,OVERALL,SOCKET SOCKET OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AGNJJ 04DIAMETER,OPENING OPENING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN OPENING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGNKJ 04LENGTH,PRONG,SOCKET SOCKET PRONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGNLJ 04WIDTH,SOCKET SOCKET WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGNMJ 04LENGTH,SOCKET SOCKET LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGNNL 16STYLE,PLATE,CLINCH,SNAP FASTENER SNAP FASTENER CLINCH PLATE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SNAP FASTENER CLINCH PLATE. 1L MODE REPLY 0 AGNPJ 04LENGTH,PRONG,PLATE PLATE PRONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGNQJ 04LENGTH,PLATE PLATE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A PLATE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AGNRJ 04LENGTH,OVERALL,CAP CAP OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGNSJ 04LENGTH,SHANK,CAP CAP SHANK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGNTJ 04DIAMETER,SHANK,CAP CAP SHANK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGNUJ 04DIAMETER,HEAD,CAP CAP HEAD DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGNVJ /D/ 04WIDTH,OVERALL,HEAD HEAD OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGNWL 16STYLE,POST,SNAP FASTENER SNAP FASTENER POST STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SNAP FASTENER POST. 1L MODE REPLY 0 AGNXJ 04LENGTH,OVERALL,POST POST OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGNYJ 04DIAMETER,HEAD,POST POST HEAD DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGNZJ 04DIAMETER,SHANK,POST POST SHANK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGPAJ 04DIAMETER,BASE,POST POST BASE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGPBJ 04WIDTH ACROSS FLATS,BASE,POST POST BASE WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGPCD 11METHOD,RETENTION,STUD STUD RETENTION METHOD THE MEANS BY WHICH THE STUD IS ASSEMBLED TO THE END ITEM. SELECT REPLY CODE 10AE94 AGPDA 12QUANTITY,ACCOMMODATED,SOCKET SOCKET ACCOMMODATED QUANTITY THE NUMBER OF SOCKETS THAT THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 AGPEL 16STYLE,STUD,TURNBUTTON TURNBUTTON STUD STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TURNBUTTON STUD. 1L MODE REPLY 0 AGPFJ 04WIDTH,BUTTON BUTTON WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGPGJ 04THICKNESS,BUTTON BUTTON THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGPHJ 04DIAMETER,HOLE,STUD STUD HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGPJJ 04DISTANCE BETWEEN STUD HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN STUD HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AGPKL 16STYLE,SOCKET,TURNBUTTON TURNBUTTON SOCKET STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TURNBUTTON SOCKET. 1L MODE REPLY 0 AGPLJ 04WIDTH,OVERALL,SOCKET SOCKET OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGPMJ 04LENGTH,OVERALL,SOCKET SOCKET OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGPNJ 04LENGTH,HOLE,SOCKET SOCKET HOLE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGPPJ 04WIDTH,HOLE,SOCKET SOCKET HOLE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGPQL 16STYLE,PLATE,CLINCH,TURNBUTTON TURNBUTTON CLINCH PLATE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TURNBUTTON CLINCH PLATE. 1L MODE REPLY 0 AGPRL 16STYLE,LATCH LATCH STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LATCH. 1L MODE REPLY 0 AGPSJ 04LENGTH,OVERALL,LATCH LATCH OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGPTJ 04DIAMETER,NOTCH NOTCH DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGPUL 16STYLE,GUIDE,LATCH LATCH GUIDE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LATCH GUIDE. 1L MODE REPLY 0 AGPVL 16STYLE,POST,SNAPSLIDE SNAPSLIDE POST STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SNAPSLIDE POST. 1L MODE REPLY 0 AGPWJ 04DIAMETER,OUTSIDE,HEAD HEAD OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGPXJ 04DIAMETER,OUTSIDE,SHOULDER SHOULDER OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SHOULDER,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGPYJ 04LENGTH,SHOULDER,POST POST SHOULDER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGPZL 16STYLE,STUD,SNAPSLIDE SNAPSLIDE STUD STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SNAPSLIDE STUD. 1L MODE REPLY 0 AGQAJ 04DIAMETER,LARGEST LARGEST DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE LARGEST CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGQBJ 04LENGTH,NECK NECK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE NECK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AGQCL 16STYLE,STUD,PUSH BUTTON PUSH BUTTON STUD STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARNCE OF THE PUSH BUTTON STUD. 1L MODE REPLY 0 AGQDJ 04DIAMETER,OUTSIDE,BASE BASE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BASE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGQEJ /D/ 04WIDTH ACROSS FLATS,BASE BASE WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGQFJ 04DIAMETER,OUTSIDE,BODY FLANGE BODY FLANGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGQGL 16STYLE,SOCKET,PUSH BUTTON PUSH BUTTON SOCKET STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PUSH BUTTON SOCKET. 1L MODE REPLY 0 AGQHL /D/ 16STYLE,PLATE,CLINCH,PUSH BUTTON PUSH BUTTON CLINCH PLATE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PUSH BUTTON CLINCH PLATE. 1L MODE REPLY 0 AGQJL 16STYLE,STUD,HEAD,POSITIVE LOCK POSITIVE LOCK STUD HEAD STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE POSITIVE LOCK STUD HEAD. 1L MODE REPLY 0 AGQKJ 04LENGTH,DIAMETER,MAJOR MAJOR DIAMETER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGQLJ 04LENGTH,UNDERCUT UNDERCUT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGQMJ 04LENGTH,OVERALL,END END OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 AGQNL 16STYLE,SHANK,POSITIVE LOCK STUD POSITIVE LOCK STUD SHANK STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE POSITIVE LOCK STUD SHANK. 1L MODE REPLY 0 AGQPJ 04DIAMETER,MAJOR,SHANK SHANK MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGQQJ 04DIAMETER,MINOR,SHANK SHANK MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGQRJ /D/ 04LENGTH,DIAMETER,MAJOR,STUD STUD MAJOR DIAMETER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGQSL 16STYLE,RECEPTACLE,POSITIVE LOCK POSITIVE LOCK RECEPTACLE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE POSITIVE LOCK RECEPTACLE. 1L MODE REPLY 0 AGQTJ 04DISTANCE BETWEEN MOUNTING HOLES ALONG LENGTH,CENTER TO CENTER,SHORTEST SHORTEST CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGQUJ 04DISTANCE FROM STUD HOLE CENTER TO MOUNTING HOLE CENTER DISTANCE FROM STUD HOLE CENTER TO MOUNTING HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGQVJ 04DISTANCE FROM STUD HOLE CENTER TO MOUNTING HOLE CENTER ALONG LENGTH DISTANCE FROM STUD HOLE CENTER TO MOUNTING HOLE CENTER ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGQWJ /D/ 04DISTANCE FROM STUD HOLE CENTER TO MOUNTING HOLE CENTER ALONG LENGTH,LONGEST LONGEST DISTANCE FROM STUD HOLE CENTER TO MOUNTING HOLE CENTER ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGQXJ /D/ 10LOAD RATING,VERTICAL VERTICAL LOAD RATING THE VERTICAL PULL FOR WHICH THE ITEM IS RATED,PER SPECIFIC MEASUREMENT SCALE. 1D AND 1B MODE REPLY12AB16 AGQYL 16STYLE,SHANK,TURNLOCK STUD TURNLOCK STUD SHANK STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TURNLOCK STUD SHANK. 1L MODE REPLY 0 AGQZD /D/ 09MATERIAL,PRECIOUS PRECIOUS MATERIAL IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM. SELECT REPLY CODE 10AD09 AGRAJ 04LENGTH,DIAMETER,MINOR MINOR DIAMETER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGRBJ 04DEPTH,FLAT FLAT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGRCJ 04LENGTH,EXTENSION EXTENSION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN EXTENSION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AGRDL 16STYLE,HEAD,TURNLOCK STUD TURNLOCK STUD HEAD STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TURNLOCK STUD HEAD. 1L MODE REPLY 0 AGREL 16STYLE,ASSEMBLY,STUD STUD ASSEMBLY STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE STUD ASSEMBLY. 1L MODE REPLY 0 AGRFJ 04DISTANCE FROM ENGAGING MEMBER TO LARGEST BEARING SURFACE OF HEAD DISTANCE FROM ENGAGING MEMBER TO LARGEST BEARING SURFACE OF HEAD NONE. 2D AND 1B MODE REPLY21AA051AC20 AGRGJ 04DISTANCE FROM STUD END TO LARGEST BEARING SURFACE OF EYELET DISTANCE FROM STUD END TO LARGEST BEARING SURFACE OF EYELET NONE. 2D AND 1B MODE REPLY21AA051AC20 AGRHJ 04DIAMETER,OUTSIDE,EYELET EYELET OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGRJJ 04DIAMETER,STUD STUD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A STUD,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGRKJ 04LENGTH,EYELET EYELET LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGRLL 16STYLE,LOCKSPRING LOCKSPRING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LOCKSPRING. 1L MODE REPLY 0 AGRMJ 04DISTANCE BETWEEN EYES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN EYES NONE. 2D AND 1B MODE REPLY21AA051AC20 AGRNJ 04DIAMETER,EYE EYE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE EYE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGRPJ 04DISTANCE,EYE CENTER TO SPRING END EYE CENTER TO SPRING END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AGRQL 16STYLE,EYELET,TURNLOCK TURNLOCK EYELET STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TURNLOCK EYELET. 1L MODE REPLY 0 AGRRJ 04HEIGHT,EYELET EYELET HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AGRSJ 04DISTANCE BETWEEN FLANGES DISTANCE BETWEEN FLANGES NONE. 2D AND 1B MODE REPLY21AA051AC20 AGRTJ 04THICKNESS,FLANGE,LARGE LARGE FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGRUJ 04DIAMETER,INSIDE,LARGEST LARGEST INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGRVJ 04DIAMETER,HOLE,MOUNTING,EYELET EYELET MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGRWB 04ANGLE IN DEG,FLANGE FLANGE ANGLE IN DEG NONE. 1B MODE REPLY 0 AGRXJ /D/ 04HEIGHT,END,SMALL SMALL END HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AGRYL 16STYLE,RECEPTACLE,TURNLOCK TURNLOCK RECEPTACLE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TURNLOCK RECEPTACLE. 1L MODE REPLY 0 AGRZJ 04LENGTH,OVERALL,RECEPTACLE RECEPTACLE OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGSAJ 04HEIGHT,RECEPTACLE RECEPTACLE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AGSBJ 04WIDTH,RECEPTACLE RECEPTACLE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGSCL 16STYLE,SPRING,EJECTOR EJECTOR SPRING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE EJECTOR SPRING. 1L MODE REPLY 0 AGSDJ 04LENGTH,OVERALL,SPRING SPRING OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE SPRING. 2D AND 1B MODE REPLY21AA051AC20 AGSEJ 04HEIGHT,SPRING SPRING HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AGSFJ 04WIDTH,SPRING SPRING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGSGJ 04DIAMETER,HOLE,MOUNTING,SPRING SPRING MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGSHJ 04DISTANCE FROM GROMMET HOLE CENTER TO MOUNTING HOLE CENTER DISTANCE FROM GROMMET HOLE CENTER TO MOUNTING HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGSJJ 04RADIUS,BEND BEND RADIUS A MEASUREMENT OF THE BEND DISTANCE OF THE ITEM FROM THE CENTERLINE TO THE AXIS. 2D AND 1B MODE REPLY21AA051AC20 AGSKD /D/ 07CAP,PROTECTIVE PROTECTIVE CAP AN INDICATION OF WHETHER OR NOT A PROTECTIVE CAP IS INCLUDED. SELECT REPLY CODE 10AA49 AGSLD /D/ 07RING,SEALING SEALING RING AN INDICATION OF WHETHER OR NOT A SEALING RING IS INCLUDED. SELECT REPLY CODE 10AA49 AGSMJ 04THICKNESS,ACCOMMODATED,MATERIAL MATERIAL ACCOMMODATED THICKNESS THE THICKNESS OF THE MATERIAL TO BE ACCOMMODATED. 2D AND 1B MODE REPLY21AA051AC20 AGSNL 16STYLE,FASTENER FASTENER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FASTENER. 1L MODE REPLY 0 AGSPJ 04DIAMETER,PRONG PRONG DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGSQJ 04WIDTH,PRONG,LARGEST LARGEST PRONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGSRJ 04LENGTH FROM HEAD TO SHOULDER LENGTH FROM HEAD TO SHOULDER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGSSJ 04LENGTH FROM HEAD TO LARGEST PRONG WIDTH LENGTH FROM HEAD TO LARGEST PRONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGSTJ 04LENGTH FROM HEAD TO TOOTH GRIP END LENGTH FROM HEAD TO TOOTH GRIP END NONE. 2D AND 1B MODE REPLY21AA051AC20 AGSUJ 04LENGTH,END,TOOTH GRIP TOOTH GRIP END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGSVJ 04LENGTH FROM BODY SHOULDER TO HOLE CENTER LENGTH FROM BODY SHOULDER TO HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGSWJ 04LENGTH FROM BODY HOLE CENTER TO BODY END LENGTH FROM BODY HOLE CENTER TO BODY END NONE. 2D AND 1B MODE REPLY21AA051AC20 AGSXJ /D/ 04LENGTH,OVERALL,FLANGE FLANGE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF A FLANGE. 2D AND 1B MODE REPLY21AA051AC20 AGSYJ 04WIDTH,OVERALL,FLANGE FLANGE OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGSZD /D/ 07GROMMET GROMMET AN INDICATION OF WHETHER OR NOT A GROMMET IS INCLUDED. SELECT REPLY CODE 10AA49 AGTAL 16STYLE,SHAPE,BASIC BASIC SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE BASIC APPEARANCE OF THE ITEM. 1L MODE REPLY 0 AGTBJ 04DISTANCE FROM RETAINER CENTER TO CENTERLINE OF MOUNTING FACILITY DISTANCE FROM RETAINER CENTER TO CENTERLINE OF MOUNTING FACILITY NONE. 2D AND 1B MODE REPLY21AA051AC20 AGTCJ 04DISTANCE FROM RETAINER CENTER TO END OF EXTENDED CLIP DISTANCE FROM RETAINER CENTER TO END OF EXTENDED CLIP NONE. 2D AND 1B MODE REPLY21AA051AC20 AGTDB 04ANGLE BETWEEN MOUNTING FACILITY AND TENSION LOOP CENTERLINES IN DEG ANGLE BETWEEN MOUNTING FACILITY AND TENSION LOOP CENTERLINES IN DEG NONE. 1B MODE REPLY 0 AGTEB 04ANGLE BETWEEN MOUNTING FACILITY AND LOOP HINGE CENTERLINES IN DEG ANGLE BETWEEN MOUNTING FACILITY AND LOOP HINGE CENTERLINES IN DEG NONE. 1B MODE REPLY 0 AGTFB 04ANGLE BETWEEN ADJACENT MOUNTING FACILITIES IN DEG ANGLE BETWEEN ADJACENT MOUNTING FACILITIES IN DEG THE ANGLE BETWEEN ADJACENT MOUNTING FACILITIES,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AGTGJ 04DISTANCE FROM RETAINER CENTER TO MOUNTING FACILITY CENTER AT LOOP TIGHTENING DEVICE DISTANCE FROM RETAINER CENTER TO MOUNTING FACILITY CENTER AT LOOP TIGHTENING DEVICE NONE. 2D AND 1B MODE REPLY21AA051AC20 AGTHJ 04DISTANCE FROM MOUNTING SURFACE TO LOCKING DEVICE DISTANCE FROM MOUNTING SURFACE TO LOCKING DEVICE NONE. 2D AND 1B MODE REPLY21AA051AC20 AGTJJ 04DISTANCE FROM MOUNTING SURFACE TO RETAINING SURFACE DISTANCE FROM MOUNTING SURFACE TO RETAINING SURFACE NONE. 2D AND 1B MODE REPLY21AA051AC20 AGTKJ 04DISTANCE BETWEEN TERMINAL HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN TERMINAL HOLES THE CENTER TO CENTER DISTANCE BETWEEN THE TERMINAL HOLES. 2D AND 1B MODE REPLY21AA051AC20 AGTLJ 04HEIGHT,CLIP,SPRING SPRING CLIP HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AGTMD 18TYPE,DEVICE,SECURING,ACCOMMODATED ITEM ACCOMMODATED ITEM SECURING DEVICE TYPE INDICATES THE TYPE OF DEVICE PROVIDED TO RETAIN OR HOLD THE ITEM ACCOMMODATED. SELECT REPLY CODE 10AC52 AGTNJ 04DISTANCE BETWEEN MOUNTING STUD CENTERS DISTANCE BETWEEN MOUNTING STUD CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGTPJ 04DISTANCE BETWEEN MOUNTING HOLE CENTERS,LATERAL LATERAL DISTANCE BETWEEN MOUNTING HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGTQJ 04DIAMETER,STUD,MOUNTING,UNTHREADED UNTHREADED MOUNTING STUD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE UNTHREADED MOUNTING STUD,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGTRJ T04DIAMETER,ACCOMMODATED,ELECTRON TUBE BASE ELECTRON TUBE BASE ACCOMMODATED DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR AN ELECTRON TUBE BASE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1F MODE REPLY11AA05 AGTSA 19ENVELOPE ACCOMMODATED,TUBE,ELECTRON,EIA EIA ELECTRON TUBE ENVELOPE ACCOMMODATED THE STANDARD ELECTRONIC INDUSTRIES ASSOCIATION DESIGNATION OF THE ENVELOPE ACCOMMODATED BY THE ELECTRON TUBE. 1A MODE REPLY 0 AGTTJ 04HEIGHT,MAXIMUM,TUBE ACCOMMODATED TUBE ACCOMMODATED MAXIMUM HEIGHT A MEASUREMENT OF THE TUBE FROM THE BOTTOM OF THE BASE TO THE TOP OF THE ENVELOPE ACCOMMODATED BY THE ITEM. 1D AND 1B MODE REPLY11AA05 AGTUJ 04DIAMETER,MAXIMUM,TUBE ENVELOPE ACCOMMODATED TUBE ENVELOPE ACCOMMODATED MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE ENVELOPE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AGTVD /D/ 18TYPE,OPENING,SHIELD TOP SHIELD TOP OPENING TYPE INDICATES THE TYPE OF OPENING PROVIDED IN THE SHIELD TOP. SELECT REPLY CODE 10AE95 AGTWJ 04DIAMETER,OPENING,CABLE CABLE OPENING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CABLE OPENING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGTXJ 04LENGTH,OPENING,CABLE CABLE OPENING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CABLE OPENING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AGTYJ 04WIDTH,OPENING,CABLE CABLE OPENING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CABLE OPENING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AGTZD /D/ 07SPURS,HOLDING HOLDING SPURS AN INDICATION OF WHETHER OR NOT HOLDING SPURS ARE PROVIDED ON THE ITEM. SELECT REPLY CODE 10AB22 AGUAD /D/ 07TAB,LOCATING,POST POST LOCATING TAB AN INDICATION OF WHETHER OR NOT A POST LOCATING TAB IS PROVIDED ON THE ITEM. SELECT REPLY CODE 10AB22 AGUBB 10CAPACITY IN BTU PER HOUR,REFRIGERATION REFRIGERATION CAPACITY IN BTU PER HOUR THE CAPACITY OF THE ITEM AS RATED BY INDUSTRY,EXPRESSED IN BRITISH THERMAL UNITS /BTU/ OF REFRIGERATION PER HOUR. 1B MODE REPLY 0 AGUCA 12QUANTITY,UNIT PACKAGE UNIT PACKAGE QUANTITY THE NUMBER OF ITEMS CONTAINED IN THE UNIT PACKAGE. 1A MODE REPLY 0 AGUDD /D/ 18TYPE,PACKAGE,SUPPLY SUPPLY PACKAGE TYPE INDICATES THE TYPE OF PACKAGE IN WHICH THE INTERMEDIATE PACKAGES ARE CONTAINED. PLEASE USE MRC CQCT. SELECT REPLY CODE 10AE96 AGUEA 12QUANTITY,ACCOMMODATION,FUSE FUSE ACCOMMODATION QUANTITY THE NUMBER OF FUSES THE ITEM IS DESIGNED TO ACCOMMODATE /INCLUDING SPARES/. 1A MODE REPLY 0 AGUFA 12QUANTITY,ACCOMMODATION,SPARE FUSE SPARE FUSE ACCOMMODATION QUANTITY THE NUMBER OF SPARE FUSES WHICH MAY BE HELD BY THE FUSEHOLDER AND FOR WHICH NO ELECTRICAL CONNECTIONS ARE PROVIDED. 1A MODE REPLY 0 AGUGB 10CURRENT RATING IN AMPS,SHORT CIRCUIT SHORT CIRCUIT CURRENT RATING IN AMPS THE MAXIMUM VALUE OF CURRENT WHICH THE ITEM WILL CARRY MOMENTARILY WITHOUT WELDING OR STICKING OF CONTACTS,MECHANICAL FAILURE,OR DAMAGE TO THE ITEM,EXPRESSED IN AMPERES. 1B MODE REPLY 0 AGUHD /D/ 18TYPE ACCOMMODATED,TERMINAL,FUSE FUSE TERMINAL TYPE ACCOMMODATED INDICATES THE TYPE OF FUSE TERMINATIONS ACCOMMODATED BY THE FUSEHOLDER. SELECT REPLY CODE 10AA58 AGUJJ 04LENGTH,FUSE,ACCOMMODATED ACCOMMODATED FUSE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A FUSE THE ITEM CAN ACCOMMODATE. 2D AND 1B MODE REPLY21AA051AC20 AGUKJ 04DIAMETER,FERRULE,ACCOMMODATED ACCOMMODATED FERRULE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED FERRULE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGULJ 04WIDTH,FUSE,ACCOMMODATED ACCOMMODATED FUSE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ACCOMMODATED FUSE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AGUMJ 04THICKNESS,FUSE,ACCOMMODATED ACCOMMODATED FUSE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE ACCOMMODATED FUSE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AGUNJ 10RESISTOR RATING RESISTOR RATING THE RATED OHMIC VALUE OF THE RESISTOR/S/ FURNISHED WITH THE ITEM. 1D AND 1B MODE REPLY11AA57 AGUPF T10VOLTAGE RANGE IN VOLTS,LAMP,INDICATING INDICATING LAMP VOLTAGE RANGE IN VOLTS THE MINIMUM TO MAXIMUM VOLTAGE AT WHICH THE INDICATING LAMP CIRCUIT IS DESIGNED TO OPERATE,EXPRESSED IN VOLTS. 1F MODE REPLY 0 AGUQD /D/ 19CONFIGURATION,CIRCUIT,INTERNAL INTERNAL CIRCUIT CONFIGURATION THE PATTERN OF CONDUCTORS AND CONNECTIONS WITHIN THE ITEM WHICH WHEN FUSED PROVIDES ELECTRICAL CONTINUITY TO MAINLINE CIRCUITS OR FROM MAINLINE TO BRANCH CIRCUITS,AS APPLICABLE. SELECT REPLY CODE 10AE97 AGURJ 04DISTANCE BETWEEN FUSE CONTACTS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FUSE CONTACTS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGUSJ /D/ 04HEIGHT,BARRIER BARRIER HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AGUTJ 04LENGTH FROM FRONT PROTRUSION TO MOUNTING SURFACE LENGTH FROM FRONT PROTRUSION TO MOUNTING SURFACE NONE. 2D AND 1B MODE REPLY21AA051AC20 AGUUJ 04THREAD LENGTH,BUSHING BUSHING THREAD LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGUVJ 04DIAMETER,CAP CAP DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CAP,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGUWJ 04HEIGHT,HOLE,MOUNTING MOUNTING HOLE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AGUXJ 04WIDTH,HOLE,MOUNTING MOUNTING HOLE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING HOLE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AGUYJ /D/ 04DISTANCE FROM HOLE CENTERLINE NEAREST LENGTH EDGE TO LENGTH EDGE DISTANCE FROM HOLE CENTERLINE NEAREST LENGTH EDGE TO LENGTH EDGE NONE. 2D AND 1B MODE REPLY21AA051AC20 AGUZJ /D/ 04DISTANCE FROM HOLE CENTERLINE NEAREST WIDTH EDGE TO WIDTH EDGE DISTANCE FROM HOLE CENTERLINE NEAREST WIDTH EDGE TO WIDTH EDGE NONE. 2D AND 1B MODE REPLY21AA051AC20 AGVAJ 04DISTANCE BETWEEN OUTSIDE MOUNTING HOLES ALONG LENGTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN OUTSIDE MOUNTING HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGVBJ 04DISTANCE BETWEEN OUTSIDE MOUNTING HOLES ALONG WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN OUTSIDE MOUNTING HOLES ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGVCJ 04DISTANCE BETWEEN INSIDE MOUNTING HOLES ALONG WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN INSIDE MOUNTING HOLES ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGVDJ 04DISTANCE BETWEEN INSIDE MOUNTING HOLES ALONG LENGTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN INSIDE MOUNTING HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGVEJ 10DC,OPERATING OPERATING DC THE VALUE OF DIRECT CURRENT REQUIRED TO MAINTAIN THE RATED PERFORMANCE OF AN ITEM. 2D AND 1B MODE REPLY21AC301AC20 AGVFJ 04DIAMETER,HOLE,BUSHING BUSHING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BUSHING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGVGJ /D/ 04LENGTH,HOLE AND KEYWAY,BUSHING BUSHING HOLE AND KEYWAY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGVHJ 04LENGTH,HOLE,FLATTED SIDE BUSHING FLATTED SIDE BUSHING HOLE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGVJJ 04DISTANCE BETWEEN BUSHING HOLE AND MOUNTING HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN BUSHING HOLE AND MOUNTING HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 AGVKJ 04DISTANCE BETWEEN BUSHING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN BUSHING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AGVLJ 04DISTANCE BETWEEN BUSHING HOLES,CENTER TO CENTER,SECOND SECOND CENTER TO CENTER DISTANCE BETWEEN BUSHING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AGVMJ 04DISTANCE BETWEEN KEYWAY AND BUSHING HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN KEYWAY AND BUSHING HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 AGVNA /D/ 13THREAD SIZE,SHAFT SHAFT THREAD SIZE DESIGNATES THE SHAFT THREAD DIAMETER AND NUMBER OF THREADS PER INCH. 1A MODE REPLY 0 AGVPA /D/ 16STYLE,CLIP CLIP STYLE THE STYLE DESIGNATION INDICATING A CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE DEVICE THAT CLASPS AND HOLDS TIGHTLY AN ITEM. 1A MODE REPLY 0 AGVQB /D/ 10CURRENT RATING IN AMPS,UL APPROVED UL APPROVED CURRENT RATING IN AMPS THE MAXIMUM CURRENT RATING THE UNDERWRITERS LABORATORIES,INCORPORATED HAS APPROVED FOR A NORMAL SAFE OPERATION,EXPRESSED IN AMPERES. 1B MODE REPLY 0 AGVRA /D/ 16STYLE,ADAPTER ADAPTER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ADAPTER. 1A MODE REPLY 0 AGVSA /D/ 16STYLE,BEARING,BALL BALL BEARING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BALL BEARING. 1A MODE REPLY 0 AGVTJ 04WIDTH,RING,OUTER OUTER RING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGVUJ 04WIDTH,RING,INNER INNER RING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGVVJ 04DIAMETER,OUTSIDE,OUTER RING OUTER RING OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGVWJ /D/ 04DIAMETER,OUTSIDE,BEARING HOUSING BEARING HOUSING OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGVXJ /D/ 04DIAMETER,PITCH,RIVET HOLE RIVET HOLE PITCH DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGVYJ 04DIAMETER,HOLE,RIVET RIVET HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE RIVET HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGVZJ /D/ 04DISTANCE BETWEEN FIRST MOUNTING HOLE ALONG HEIGHT AND MOUNTING HOLE ALONG WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FIRST MOUNTING HOLE ALONG HEIGHT AND MOUNTING HOLE ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGWAJ 04RADIUS,GROOVE GROOVE RADIUS A MEASUREMENT OF A LINE SEGMENT EXTENDING FROM THE CENTER OF A GROOVE TO THE INSIDE SURFACE. 2D AND 1B MODE REPLY21AA051AC20 AGWBJ 04LENGTH,SHAFT,SHORT END SHORT END SHAFT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGWCJ 04LENGTH,SHAFT,LONG END LONG END SHAFT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGWDJ 04DIAMETER,SHAFT,SHORT END SHORT END SHAFT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGWEJ 04DIAMETER,SHAFT,LONG END LONG END SHAFT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGWFB /D/ 04ANGLE IN DEG,TAPER,PIVOT PIVOT TAPER ANGLE IN DEG NONE. 1B MODE REPLY 0 AGWGJ 04RADIUS,CROWN CROWN RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGWHJ 04DIAMETER,ELEMENT,ROLLING ROLLING ELEMENT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ROLLING ELEMENT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGWJJ 04DIAMETER,SMALLEST,BORE BORE SMALLEST DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST DIAMETER OF A BORE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGWKJ 04DIAMETER,BORE,LARGEST LARGEST BORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGWLJ 04DIAMETER,OUTSIDE,SMALLEST SMALLEST OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST DIAMETER OF AN ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGWMJ 04DIAMETER,OUTSIDE,LARGEST LARGEST OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST DIAMETER OF AN ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGWNJ 04DIAMETER,PIVOT,SMALLEST FLANGE SMALLEST FLANGE PIVOT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGWPJ /D/ 04DIAMETER,PIVOT,LARGEST FLANGE LARGEST FLANGE PIVOT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGWQJ /D/ 04HEIGHT INCLUDING SEATING RING HEIGHT INCLUDING SEATING RING NONE. 2D AND 1B MODE REPLY21AA051AC20 AGWRJ 04DIAMETER,OUTSIDE,SEATING RING SEATING RING OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGWSJ /D/ 04WIDTH,BEARING,SINGLE SINGLE BEARING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGWTA /D/ 16STYLE,BEARING,ROLLER ROLLER BEARING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ROLLER BEARING. 1A MODE REPLY 0 AGWUJ 04RADIUS,CORNER,BACKFACE BACKFACE CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGWVJ 04WIDTH,STANDOUT STANDOUT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGWWJ 04RADIUS,CORNER,CONE CONE CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGWXJ 04WIDTH,CONE CONE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGWYJ 04WIDTH,CUP CUP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CUP,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AGWZJ 04DIAMETER,OUTSIDE,CUP CUP OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGXAJ /D/ 04DIAMETER,OUTSIDE,RADIAL UNIT RADIAL UNIT OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGXBJ 04DIAMETER,OUTSIDE,THRUST UNIT THRUST UNIT OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGXCA /D/ 16STYLE,BEARING,NEEDLE NEEDLE BEARING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE NEEDLE BEARING. 1A MODE REPLY 0 AGXDJ 04DIAMETER,OUTSIDE,ROLLER ROLLER OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A ROLLER,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGXEJ 04WIDTH,ROLLER ROLLER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A ROLLER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AGXFJ 04LENGTH,STUD STUD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE STUD,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AGXGA /D/ 16STYLE,BEARING,ROD END ROD END BEARING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ROD END BEARING. 1A MODE REPLY 0 AGXHJ 04LENGTH FROM BORE CENTER TO SHANK END LENGTH FROM BORE CENTER TO SHANK END NONE. 2D AND 1B MODE REPLY21AA051AC20 AGXJJ 04DIAMETER,BORE,SHANK SHANK BORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGXKJ 04DEPTH,BORE,SHANK SHANK BORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AGXLB /D/ 04ANGLE IN DEG,SELF-ALIGNMENT SELF-ALIGNMENT ANGLE IN DEG NONE. 1B MODE REPLY 0 AGXMA /D/ 16STYLE,ELEMENT,ROLLING ROLLING ELEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ROLLING ELEMENT. 1A MODE REPLY 0 AGXNJ 04RADIUS,CONVEX CONVEX RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGXPA /D/ 16STYLE,END,ROLLER ROLLER END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ROLLER END. 1A MODE REPLY 0 AGXQJ /D/ 04RADIUS,CORNER,CUP CUP CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AGXRA /D/ 16STYLE,CONE CONE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CONE. 1A MODE REPLY 0 AGXSA /D/ 16STYLE,CUP CUP STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CUP. 1A MODE REPLY 0 AGXTA /D/ 16STYLE,RETAINER RETAINER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE RETAINER. 1A MODE REPLY 0 AGXUA /D/ 16STYLE,SEAT SEAT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SEAT. 1A MODE REPLY 0 AGXVD 18TYPE,FOOD FOOD TYPE INDICATES THE TYPE OF FOOD. SELECT REPLY CODE 10AE92 AGXWD 19FORM,PHYSICAL PHYSICAL FORM THE RECOGNIZED SHAPE,CONFIGURATION,STRUCTURE,OR MOLD OF A SUBSTANCE,NATURAL OR REFINED,THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM. SELECT REPLY CODE 10AE98 AGXXD 19QUALITY,FOOD FOOD QUALITY THE RECOGNIZED TRADE DESIGNATION INDICATING THE GRADE,OR OTHER RATING TYPE,AS RELATED TO THE DEGREE OF EXCELLENCE OF THE FOOD. SELECT REPLY CODE 10AE99 AGXYJ /D/ 10CURRENT RATING,AC,CONTACT MAXIMUM RESISTIVE LOAD CONTACT MAXIMUM RESISTIVE LOAD AC CURRENT RATING THE GREATEST VALUE OF ALTERNATING CURRENT AT WHICH THE CONTACT/S/ IS RATED TO MAKE OR BREAK WITH A RESISTIVE LOAD. 1D AND 1B MODE REPLY11AC30 AGXZD /D/ 18TYPE,PACKAGE,UNIT UNIT PACKAGE TYPE INDICATES THE TYPE OF CONTAINER IN WHICH THE ITEM OF SUPPLY IS PACKAGED. PLEASE USE MRC ALQG IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AE96 AGYAA 04SIZE,CAN CAN SIZE THE RECOGNIZED TRADE DESIGNATION OR TERM INDICATING THE CAN SIZE. 1A MODE REPLY 0 AGYBD /D/ 03DESIGNATION,TOLERANCE,AFBMA STANDARD AFBMA STANDARD TOLERANCE DESIGNATION THE STANDARD TOLERANCE DESIGNATION INDICATING THE MANUFACTURED LIMITATIONS OF THE ITEM AS ESTABLISHED BY THE ANTI-FRICTION BEARING MANUFACTURERS ASSOCIATION. SELECT REPLY CODE 10AF01 AGYCA 03DESIGNATOR,CALIBRATION CALIBRATION DESIGNATOR THE ALPHA OR ALPHA-NUMERIC SYMBOL REPRESENTING A SPECIFIC CALIBRATION WITHIN A TOLERANCE LIMIT. 1A MODE REPLY 0 AGYDJ /D/ 10WEIGHT,PACKAGE,UNIT UNIT PACKAGE WEIGHT THE MEASURED WEIGHT OF THE UNIT PACKAGE;I.E.,THE ITEM OF SUPPLY AND ITS CONTAINER, 1D AND 1B MODE REPLY12AB16 AGYED 19FINISH,SURFACE SURFACE FINISH AN ADDITIONAL FINISHING PROCESS BY WHICH THE SURFACE OF AN ITEM IS ALTERED IN RESPECT TO POLISHING,GRINDING,AND THE LIKE. SELECT REPLY CODE 10AA41 AGYFD 11METHOD,FABRICATION,RETAINER RETAINER FABRICATION METHOD THE MEANS USED IN MANUFACTURING THE RETAINER. SELECT REPLY CODE 10AA62 AGYGA 12QUANTITY,PIECE,RETAINER RETAINER PIECE QUANTITY THE NUMBER OF COMPONENTS COMPRISING THE RETAINER. 1A MODE REPLY 0 AGYHD 19MECHANISM,FEED,PAPER PAPER FEED MECHANISM INDICATES THE TYPE OF PAPER FEED. SELECT REPLY CODE 10AN47 AGYJA 12QUANTITY,SEAL SEAL QUANTITY THE NUMBER OF SEALS INCLUDED ON THE ITEM. 1A MODE REPLY 0 AGYKA 12QUANTITY,SHIELD SHIELD QUANTITY THE NUMBER OF SHIELDS INCLUDED ON THE ITEM. 1A MODE REPLY 0 AGYLJ /D/A18TYPE AND QUANTITY,CHART,COLOR STANDARD COLOR STANDARD CHART TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF STANDARDIZED TESTS BASED ON THE PRINCIPLES OF COLOR REACTION INDICATOR VALUES FOR THE DETECTION OF URINE BILIRUBIN,KETONE IN URINE,GLUCOSE,AND THE LIKE. 1D AND 1A MODE REPLY12AF03 AGYMJ A19PROGRAMS,ADDITIONAL ADDITIONAL PROGRAMS AN INDICATION OF THE ADDITIONAL PROGRAMS AVAILABLE WITH THE ITEM. 1D AND 1A MODE REPLY13AN47 AGYNB 10FLASH POINT IN DEG FAHRENHEIT,MINIMUM MINIMUM FLASH POINT IN DEG FAHRENHEIT THE NUMERIC VALUE OF THE MINIMUM FLASH POINT AT WHICH THE ITEM WILL IGNITE AND BURN,EXPRESSED IN DEGREES FAHRENHEIT. 1B MODE REPLY 0 AGYPA /D/ 12QUANTITY,STRIP,TEST TEST STRIP QUANTITY THE NUMBER OF TEST STRIPS INCLUDED. 1A MODE REPLY 0 AGYQD /D/ 07AGENT INCLUDED,DESICCANT DESICCANT AGENT INCLUDED AN INDICATION OF WHETHER OR NOT A DESICCANT AGENT TO ABSORB OR DISPEL MOISTURE IS INCLUDED. SELECT REPLY CODE 10AA89 AGYRJ 04DIAMETER,COIL COIL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COIL,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AGYSJ 04DIAMETER,INSIDE,TUBE TUBE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AGYTJ 04LENGTH,TUBE TUBE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TUBE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AGYUJ 10CAPACITY,FLUID,UNIT PACKAGE UNIT PACKAGE FLUID CAPACITY THE AMOUNT OF FLUID THE UNIT PACKAGE WILL HOLD. 1D AND 1B MODE REPLY11AD73 AGYVJ 04THREAD DIAMETER,MOUNTING MOUNTING THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED MOUNTING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AGYWD 18TYPE,SEAL,BEARING BEARING SEAL TYPE INDICATES THE TYPE OF SEAL PROVIDED WITH THE BEARING. SELECT REPLY CODE 10AF04 AGYXA 12QUANTITY,GROOVE,ROLLING ELEMENT ROLLING ELEMENT GROOVE QUANTITY THE NUMBER OF GROOVES IN WHICH THE ROLLING ELEMENT RIDES. 1A MODE REPLY 0 AGYYL 16STYLE,EDGE,ATTACHING ATTACHING EDGE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ATTACHING EDGE. 1L MODE REPLY 0 AGYZD /D/ 18TYPE,ROLLER ROLLER TYPE INDICATES THE TYPE OF ROLLER/S/ PROVIDED. SELECT REPLY CODE 10AC68 AGZAD 18TYPE,ALIGNMENT ALIGNMENT TYPE INDICATES THE TYPE OF ALIGNMENT UTILIZED WHEREBY THE ITEM WILL ADJUST AXIALLY FOR MISALIGNMENT. SELECT REPLY CODE 10AF16 AGZBD /D/ 07RING,ALIGNING ALIGNING RING AN INDICATION OF WHETHER OR NOT AN ALIGNING RING IS INCLUDED. SELECT REPLY CODE 10AA49 AGZCD 05DIRECTION,LOAD LOAD DIRECTION THE DIRECTION OF LOAD WITH RESPECT TO THE SHAFT AXIS. SELECT REPLY CODE 10AA28 AGZDD 14SHAPE,BORE BORE SHAPE THE PHYSICAL CONFIGURATION OF THE BORE. SELECT REPLY CODE 10AD07 AGZED /D/ 11METHOD,MOUNTING,COLLAR COLLAR MOUNTING METHOD THE MEANS USED TO FASTEN THE COLLAR TO AN ADJACENT COMPONENT OR THE ITEM. SELECT REPLY CODE 10AB89 AGZFD 19FEATURE,LOCATING LOCATING FEATURE THE ABILITY OF THE BEARING TO PROVIDE FREEDOM FOR AXIAL MOVEMENT OF THE SHAFT RELATIVE TO THE HOUSING. SELECT REPLY CODE 10AF06 AGZGD /D/ 07FEATURE,SEPARATION SEPARATION FEATURE AN INDICATION OF WHETHER OR NOT A SEPARATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AGZHD 03DESIGNATION,FIT-UP,INTERNAL INTERNAL FIT-UP DESIGNATION THE DESIGNATION SPECIFYING THE TYPE OF FIT AS RECOGNIZED BY INDUSTRIAL AND GOVERNMENTAL AGENCIES. SELECT REPLY CODE 10AF05 AGZJD 03DESIGNATION,PRELOAD,BEARING BEARING PRELOAD DESIGNATION THE DESIGNATION SPECIFYING THE TYPE OF INTERNAL LOADING IN A BEARING WHICH IS INDEPENDENT OF ANY EXTERNAL RADIAL AND/OR AXIAL LOAD. SELECT REPLY CODE 10AF07 AGZKD 05DIRECTION,ANGULAR,INTERNAL FIT-UP CONTACT INTERNAL FIT-UP CONTACT ANGULAR DIRECTION THE DIRECTION OF THE INTERNAL FIT-UP CONTACT ANGLE AT POINT OF CONTACT. SELECT REPLY CODE 10AF08 AGZLJ /D/ 04ANGLE IN DEG,CONTACT CONTACT ANGLE IN DEG THE SIZE OF THE ANGLE FORMED AT THE FORCE POINT OF CONTACT,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 AGZMD /D/ 11METHOD,MOUNTING,EXTERNAL EXTERNAL MOUNTING METHOD THE MEANS USED TO EXTERNALLY POSITION THE ITEM. SELECT REPLY CODE 10AB89 AGZND /D/ 08LOCATION,DEVICE,EXTERNAL MOUNTING EXTERNAL MOUNTING DEVICE LOCATION INDICATES THE LOCATION OF THE EXTERNAL MOUNTING DEVICE ON THE ITEM. SELECT REPLY CODE 10AE46 AGZPG 19ARRANGEMENT,STACK STACK ARRANGEMENT THE ARRANGEMENT OF THE ASSEMBLED ITEM(S). FULL TEXT WRITE-IN 0 AGZQD 03DESIGNATION,CAPABILITY,DIRECTIONAL,THRUST THRUST DIRECTIONAL CAPABILITY DESIGNATION A DESIGNATION OF THE DIRECTIONAL OPERATING CAPABILITY OF THE ITEM. SELECT REPLY CODE 10AF09 AGZRA 12QUANTITY,HOLE,RIVET RIVET HOLE QUANTITY THE NUMBER OF RIVET HOLES INCLUDED ON THE ITEM. 1A MODE REPLY 0 AGZSD /D/ 08LOCATION,SEAL,BEARING BEARING SEAL LOCATION INDICATES THE LOCATION OF THE SEALING ELEMENT IN RESPECT TO THE OUTER RING. SELECT REPLY CODE 10AE46 AGZTA 12QUANTITY,BALL,BEARING BEARING BALL QUANTITY THE NUMBER OF SPHERICAL BODIES WHICH ARE THE ROLLING ELEMENTS OF THE BEARING. 1A MODE REPLY 0 AGZUJ /D/ 04DIAMETER,OUTSIDE,INNER RING INNER RING OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AGZVD 18TYPE,MATERIAL,FATTY FATTY MATERIAL TYPE INDICATES THE TYPE OF FATTY MATERIAL OF WHICH THE ITEM IS COMPOSED. SELECT REPLY CODE 10AF10 AGZWF /D/T10RANGE,PERCENTAGE,FATTY MATERIAL FATTY MATERIAL PERCENTAGE RANGE THE SPECIFIC PERCENTAGE RANGE OF FATTY MATERIAL FOR THE ITEM. 1F MODE REPLY 0 AGZXD 19INGREDIENT,BASIC BASIC INGREDIENT THE PRIMARY INGREDIENT OF WHICH THE ITEM IS MADE. SELECT REPLY CODE 10AF11 AGZYD /D/ 18TYPE,BASE,MATERIAL MATERIAL BASE TYPE INDICATES THE TYPE OF MATERIAL BASE OF WHICH THE ITEM IS COMPOSED. SELECT REPLY CODE 10AF12 AGZZG 10VISCOSITY AT RATED TEMP VISCOSITY AT RATED TEMP THE KINEMATIC UNITS /CENTISTOKES/ OF THE ITEM AT A SPECIFIED TEMPERATURE. FULL TEXT WRITE-IN 0 AHAAG 10VISCOSITY AT RATED TEMP,MAXIMUM MAXIMUM VISCOSITY AT RATED TEMP THE MAXIMUM KINEMATIC UNITS /CENTISTOKES/ OF THE ITEM AT A SPECIFIED TEMPERATURE. FULL TEXT WRITE-IN 0 AHACG 10VISCOSITY AT RATED TEMP,MINIMUM MINIMUM VISCOSITY AT RATED TEMP THE MINIMUM KINEMATIC UNITS /CENTISTOKES/ OF THE ITEM AT A SPECIFIED TEMPERATURE. FULL TEXT WRITE-IN 0 AHADB 10INDEX,VISCOSITY,MINIMUM MINIMUM VISCOSITY INDEX THE NUMERIC VALUE OF THE MINIMUM VISCOSITY INDEX OF THE ITEM. 1B MODE REPLY 0 AHAEB /D/ 10POUR POINT IN DEG FAHRENHEIT POUR POINT IN DEG FAHRENHEIT THE LOWEST TEMPERATURE AT WHICH THE ITEM WILL POUR,EXPRESSED IN DEGREES FAHRENHEIT. 1B MODE REPLY 0 AHAFB /D/ 10PRESSURE IN DEG CENTIGRADE,VAPOR,MAXIMUM MAXIMUM VAPOR PRESSURE IN DEG CENTIGRADE THE MAXIMUM VAPOR PRESSURE FOR WHICH THE ITEM IS RATED,EXPRESSED IN DEGREES CENTIGRADE. 1B MODE REPLY 0 AHAGF /D/T10RANGE IN DEG FAHRENHEIT,TEMP,RATED EFFECTIVE RATED EFFECTIVE TEMP RANGE IN DEG FAHRENHEIT THE NUMERIC VALUE OF THE EFFECTIVE TEMPERATURE RANGE OF THE ITEM,EXPRESSED IN DEGREES FAHRENHEIT. 1F MODE REPLY 0 AHAHF /D/T10RANGE IN DEG FAHRENHEIT,TEMP,RATED EFFECTIVE LIQUID FILM RATED EFFECTIVE LIQUID FILM TEMP RANGE IN DEG FAHRENHEIT THE NUMERIC VALUE OF THE EFFECTIVE LIQUID FILM TEMPERATURE RANGE OF THE ITEM,EXPRESSED IN DEGREES FAHRENHEIT. 1F MODE REPLY 0 AHAJJ 10FREQUENCY PER FUNCTION,REFERENCE REFERENCE FREQUENCY PER FUNCTION THE FREQUENCY AT WHICH THE INSERTION LOSS IS MEASURED PER FUNCTION,AND TO WHICH ALL RELATED ATTENUATION LOSS MEASUREMENTS ARE REFERRED. 2D AND 1B MODE REPLY21AE062AF15 AHAKD 18TYPE,LUBRICANT LUBRICANT TYPE INDICATES THE TYPE OF LUBRICANT FURNISHED. SELECT REPLY CODE 10AF14 AHALJ /D/ 10LOSS AT REFERENCE FREQUENCY IN DECIBELS,INSERTION INSERTION LOSS AT REFERENCE FREQUENCY IN DECIBELS THE RATIO OF POWER DELIVERED TO THE LOAD BEFORE INSERTION OF THE FILTER,TO THE POWER DELIVERED TO THE LOAD AFTER INSERTION OF THE FILTER,EXPRESSED IN DECIBELS. 1D AND 1B MODE REPLY12AF15 AHAMJ /D/ 10WIDTH PER FUNCTION,BAND,FREQUENCY FREQUENCY BAND WIDTH PER FUNCTION THE DIFFERENCE BETWEEN THE LIMITING FREQUENCIES WITH WHICH PERFORMANCE,IN RESPECT TO SOME CHARACTERISTIC,FALLS WITHIN SPECIFIED LIMITS./ASA C42.65 PARAGRAPH 65.02.030/. 3D AND 1B MODE REPLY31AE062AH512AF15 AHANJ /D/ 10FREQUENCIES OF DISCRIMINATION PER FUNCTION,SPECIFIED SPECIFIED FREQUENCIES OF DISCRIMINATION PER FUNCTION THE SPECIFIED FREQUENCIES AT WHICH LOSSES IN SIGNAL STRENGTH ARE,BY DESIGN OR MEASUREMENT,ESTABLISHED IN A FILTER CIRCUIT. 3D AND 1B MODE REPLY31AE061AF132AF15 AHAPJ /D/ 10DISCRIMINATION AT SPECIFIED FREQUENCIES PER FUNCTION IN DECIBELS DISCRIMINATION AT SPECIFIED FREQUENCIES PER FUNCTION IN DECIBELS THE ALGEBRAIC DIFFERENCE BETWEEN THE INSERTION LOSS AT A SPECIFIED FREQUENCY AND THE INSERTION LOSS AT THE REFERENCE FREQUENCY,EXPRESSED IN DECIBELS. 3D AND 1B MODE REPLY31AC201AF132AF15 AHAQJ 10IMPEDANCE RATING PER FUNCTION,SOURCE SOURCE IMPEDANCE RATING PER FUNCTION THE TOTAL OPPOSITION PER FUNCTION,PRESENTED BY A SOURCE OF ENERGY TO THE INPUT TERMINALS OF AN ITEM. 2D AND 1B MODE REPLY21AA572AF15 AHARJ /D/ 10RATIO PER FUNCTION,IMPEDANCE,TRANSFER TRANSFER IMPEDANCE RATIO PER FUNCTION THE RATIO,AT THE REFERENCE FREQUENCY,OF THE SIGNAL VOLTAGE AT THE OUTPUT TERMINALS TO THE INPUT SIGNAL CURRENT. 2D AND 1B MODE REPLY21AA572AF15 AHASJ 10IMPEDANCE PER FUNCTION,LOAD LOAD IMPEDANCE PER FUNCTION THE TOTAL OPPOSITION PER FUNCTION,PRESENTED BY A LOAD TO THE OUTPUT TERMINALS OF AN ITEM. 2D AND 1B MODE REPLY21AA572AF15 AHAUJ 10IMPEDANCE PER FUNCTION W/LOAD,INPUT INPUT IMPEDANCE PER FUNCTION W/LOAD THE TOTAL OPPOSITION PER FUNCTION WITH LOAD (RESISTIVE AND REACTIVE) PRESENTED BY THE DEVICE TO THE SOURCE (ASA C42.65,PARAGRAPH 65.08.399). 2D AND 1B MODE REPLY21AA572AF15 AHAVJ 10IMPEDANCE PER FUNCTION W/SOURCE ACROSS INPUT,OUTPUT OUTPUT IMPEDANCE PER FUNCTION W/SOURCE ACROSS INPUT THE TOTAL OPPOSITION PER FUNCTION WITH SOURCE ACROSS INPUT (RESISTIVE AND REACTIVE) PRESENTED BY THE DEVICE TO THE LOAD (ASA C42.65,PARAGRAPH 65.08.402). 2D AND 1B MODE REPLY21AA572AF15 AHAWD 08LOCATION,SELF-ALIGNMENT SELF-ALIGNMENT LOCATION INDICATES THE LOCATION OF THE SELF-ALIGNMENT FEATURE. SELECT REPLY CODE 10AE46 AHAXD /D/ 19FEATURE,HOLE/GROOVE,SHAFT SHAFT HOLE/GROOVE FEATURE AN INDICATION OF THE PRESENCE OF A HOLE AND/OR GROOVE ON THE SHAFT. SELECT REPLY CODE 10AB99 AHAYJ /D/ 10RATING PER FUNCTION,POWER,PEAK PEAK POWER RATING PER FUNCTION THE GREATEST INSTANTANEOUS AMOUNT OF ELECTRICAL ENERGY FOR WHICH THE ITEM WAS DESIGNED TO PASS OR DISSIPATE. 2D AND 1B MODE REPLY21AC332AF15 AHAZJ /D/ 10FREQUENCY PER FUNCTION,RATING,PEAK POWER PEAK POWER RATING FREQUENCY PER FUNCTION THE FREQUENCY AT WHICH THE PEAK POWER RATING APPLIES. 2D AND 1B MODE REPLY21AE062AF15 AHBAH /D/ 19CURRENT PER FUNCTION FOR WHICH DESIGNED,CIRCUIT CIRCUIT CURRENT PER FUNCTION FOR WHICH DESIGNED THE TYPE OF ELECTRICAL CURRENT FOR WHICH THE ITEM IS DESIGNED. 2D MODE REPLY 21AB622AF15 AHBBJ 10FREQUENCY RATING PER FUNCTION IN HERTZ,LINE,POWER POWER LINE FREQUENCY RATING PER FUNCTION IN HERTZ THE CYCLES PER SECOND /HERTZ/ OF THE POWER LINE ALTERNATING CURRENT. 1D AND 1B MODE REPLY12AF15 AHBCJ 10CURRENT RATING PER FUNCTION IN AMPS,OPERATING OPERATING CURRENT RATING PER FUNCTION IN AMPS THE LEVEL OF ELECTRICAL FLOW,PER FUNCTION,FOR WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN AMPERS. 1D AND 1B MODE REPLY12AF15 AHBDJ /D/ 10VOLTAGE RATING PER FUNCTION,OPERATING OPERATING VOLTAGE RATING PER FUNCTION THE LEVEL OF ELECTRICAL POTENTIAL FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AB632AF15 AHBEJ 10VOLTAGE DROP PER FUNCTION,MAXIMUM MAXIMUM VOLTAGE DROP PER FUNCTION THE GREATEST AMOUNT OF VOLTAGE LOSS PER FUNCTION,RESULTING FROM THE DEVICES INHERENT OPPOSITION TO THE FLOW OF ELECTRICAL CURRENT. 3D AND 1B MODE REPLY31AB631AB622AF15 AHBFJ /D/ 10VOLTAGE AT SEA LEVEL,AC RMS,DIELECTRIC WITHSTANDING,MAXIMUM MAXIMUM DIELECTRIC WITHSTANDING AC RMS VOLTAGE AT SEA LEVEL THE MAXIMUM ALTERNATING CURRENT ROOT MEAN SQUARE VOLTAGE THAT THE INSULATING MATERIAL/S/ OF THE ITEM WILL WITHSTAND WITHOUT RESULTING IN DISRUPTIVE DISCHARGE OR DETERIORATION AT SEA LEVEL /ATMOSPHERIC/. 1D AND 1B MODE REPLY11AB63 AHBGJ /D/ 10VOLTAGE AT ALTITUDE,AC RMS,DIELECTRIC WITHSTANDING,MAXIMUM MAXIMUM DIELECTRIC WITHSTANDING AC RMS VOLTAGE AT ALTITUDE THE MAXIMUM ALTERNATING CURRENT ROOT MEAN SQUARE VOLTAGE THAT THE INSULATING MATERIAL/S/ OF THE ITEM WILL WITHSTAND WITHOUT RESULTING IN DISRUPTIVE DISCHARGE OR DETERIORATION AT ALTITUDE /REDUCED BAROMETRIC PRESSURE/. 1D AND 1B MODE REPLY11AB63 AHBHJ /D/ 10VOLTAGE AT SEA LEVEL,DC,DIELECTRIC WITHSTANDING,MAXIMUM MAXIMUM DIELECTRIC WITHSTANDING DC VOLTAGE AT SEA LEVEL THE MAXIMUM DIRECT CURRENT VOLTAGE THAT THE INSULATING MATERIAL/S/ OF THE ITEM WILL WITHSTAND WITHOUT RESULTING IN DISRUPTIVE DISCHARGE OR DETERIORATION AT SEA LEVEL /ATMOSPHERIC/. 1D AND 1B MODE REPLY11AB63 AHBJJ /D/ 10VOLTAGE AT ALTITUDE,DC,DIELECTRIC WITHSTANDING,MAXIMUM MAXIMUM DIELECTRIC WITHSTANDING DC VOLTAGE AT ALTITUDE THE MAXIMUM DIRECT CURRENT VOLTAGE THAT THE INSULATING MATERIAL/S/ OF THE ITEM WILL WITHSTAND WITHOUT RESULTING IN DISRUPTIVE DISCHARGE OR DETERIORATION AT ALTITUDE /REDUCED BAROMETRIC PRESSURE/. 1D AND 1B MODE REPLY11AB63 AHBKJ /D/ 10CAPACITANCE TO GROUND PER FUNCTION,MINIMUM MINIMUM CAPACITANCE TO GROUND PER FUNCTION THE LOWEST PERMISSIBLE CAPACITANCE VALUE BETWEEN THE ITEMS INPUT TERMINAL(S) AND ITS GROUND TERMINAL(S). 2D AND 1B MODE REPLY22AE752AF15 AHBLH 18TYPE PER FUNCTION,CIRCUITRY,PRINCIPAL PRINCIPAL CIRCUITRY TYPE PER FUNCTION INDICATES THE TYPE OF PRINCIPAL CIRCUITRY PER FUNCTION INTERCONNECTED WITHIN THE ITEM TO PRODUCE THE DESIRED FREQUENCY VERSUS ATTENUATION CHARACTERISTICS. 2D MODE REPLY 22AF172AF15 AHBMD 18TYPE,TERMINAL,INPUT INPUT TERMINAL TYPE INDICATES THE TYPE OF INPUT TERMINAL(S) FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. SELECT REPLY CODE 10AA58 AHBNA 19CODE,MANUFACTURER,INPUT TERMINAL INPUT TERMINAL MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE INPUT TERMINAL. 1A MODE REPLY 0 AHBPA 19IDENTIFICATION,TERMINAL,INPUT INPUT TERMINAL IDENTIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS IDENTIFICATION NUMBER OR SYMBOL USED TO IDENTIFY THE INPUT TERMINAL. 1A MODE REPLY 0 AHBQA /D/ 12QUANTITY,TERMINAL,INPUT INPUT TERMINAL QUANTITY THE NUMBER OF INPUT TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. 1A MODE REPLY 0 AHBRD /D/ 18TYPE,TERMINAL,OUTPUT OUTPUT TERMINAL TYPE INDICATES THE TYPE OF OUTPUT TERMINAL(S) FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. SELECT REPLY CODE 10AA58 AHBSA 19CODE,MANUFACTURER,OUTPUT TERMINAL OUTPUT TERMINAL MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE OUTPUT TERMINAL. 1A MODE REPLY 0 AHBTA 19IDENTIFICATION,TERMINAL,OUTPUT OUTPUT TERMINAL IDENTIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS IDENTIFICATION NUMBER OR SYMBOL USED TO IDENTIFY THE OUTPUT TERMINAL. 1A MODE REPLY 0 AHBUA /D/ 12QUANTITY,TERMINAL,OUTPUT OUTPUT TERMINAL QUANTITY THE NUMBER OF OUTPUT TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. 1A MODE REPLY 0 AHBVD /D/ 18TYPE,TERMINAL,GROUND GROUND TERMINAL TYPE INDICATES THE TYPE OF GROUND TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. SELECT REPLY CODE 10AA58 AHBWA /D/ 12QUANTITY,TERMINAL,GROUND GROUND TERMINAL QUANTITY THE NUMBER OF GROUND TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. 1A MODE REPLY 0 AHBXJ 04DISTANCE BETWEEN MOUNTING SURFACE AND LOWER END DISTANCE BETWEEN MOUNTING SURFACE AND LOWER END NONE. 2D AND 1B MODE REPLY21AA051AC20 AHBYJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,TERMINAL TERMINAL THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE FOR THE TERMINAL. 1D AND 1A MODE REPLY12AH06 AHBZJ 10RATIO PER FUNCTION,WAVE,STANDING,VOLTAGE VOLTAGE STANDING WAVE RATIO PER FUNCTION THE RATIO OF THE MAXIMUM TO THE MINIMUM VOLTAGE OF THE STANDING WAVE PER FUNCTION. THE LARGER RELATIVE PORTION IS GIVEN,THE LOWER VALUE HAVING AN IMPLIED /NOT GIVEN/ VALUE OF ONE /UNITY/. 1D AND 1B MODE REPLY12AF15 AHCAJ /D/ 10RANGE PER FUNCTION,FREQUENCY,VOLTAGE STANDING WAVE RATIO VOLTAGE STANDING WAVE RATIO FREQUENCY RANGE PER FUNCTION THE MINIMUM AND MAXIMUM VALUES OF FREQUENCY BETWEEN WHICH THE VOLTAGE STANDING WAVE RATIO IS SPECIFIED. 3D AND 1B MODE REPLY31AE062AH512AF15 AHCBJ /D/ 10VOLTAGE RATING PER FUNCTION,SIGNAL,NOMINAL NOMINAL SIGNAL VOLTAGE RATING PER FUNCTION THE NOMINAL VALUE OF SIGNAL VOLTAGE WHICH THE ITEM MAY HAVE APPLIED TO ITS INPUT TERMINALS. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 3D AND 1B MODE REPLY31AB631AF652AF15 AHCCJ /D/ 10LIMITS PER FUNCTION,VOLTAGE,SIGNAL INPUT SIGNAL INPUT VOLTAGE LIMITS PER FUNCTION THE LOWER AND UPPER VALUES OF THE NOMINAL SIGNAL VOLTAGE,PER FUNCTION,WHICH THE ITEM MAY HAVE APPLIED TO ITS INPUT TERMINALS. 3D AND 1B MODE REPLY31AB632AH512AF15 AHCDB /D/ 10CAPACITANCE IN PICOFARADS,RESONATING RESONATING CAPACITANCE IN PICOFARADS THE NOMINAL VALUE OF THE TOTAL CAPACITANCE,EXTERNAL TO AN ITEM AT ITS INPUT AND OUTPUT TERMINATIONS,WHICH IS REQUIRED TO RESONATE THE ITEM AT ITS DESIGN FREQUENCY. 1B MODE REPLY 0 AHCEF /D/T10RANGE IN PICOFARADS,CAPACITANCE,RESONATING RESONATING CAPACITANCE RANGE IN PICOFARADS THE LOWER AND UPPER LIMITS,BETWEEN WHICH THE RESONATING CAPACITANCE MAY VARY,EXPRESSED IN PICOFARADS. 1F MODE REPLY 0 AHCFJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,STUD,MOUNTING MOUNTING STUD THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE FOR THE MOUNTING STUD. 1D AND 1A MODE REPLY12AH06 AHCGJ 10RISE,TEMP,MAXIMUM MAXIMUM TEMP RISE THE MAXIMUM PERMISSIBLE TEMPERATURE INCREASE IN THE ITEM AS A RESULT OF ITS OPERATION UNDER NORMAL CONDITIONS. 1D AND 1B MODE REPLY11AB36 AHCHJ 10POWER RATING PER FUNCTION,AVERAGE AVERAGE POWER RATING PER FUNCTION THE VALUE OF THE AVERAGE AMOUNT OF ELECTRICAL ENERGY PER FUNCTION,WHICH THE ITEM MAY PASS OR DISSIPATE IN CONTINUOUS OPERATION WITHOUT DEGRADATION OF PHYSICAL OR ELECTRICAL CHARACTERISTICS. 2D AND 1B MODE REPLY21AC332AF15 AHCJB 10FREQUENCIES IN MEGAHERTZ,LOSS,FULL LOAD INSERTION FULL LOAD INSERTION LOSS FREQUENCIES IN MEGAHERTZ THE SPECIFIED POINTS IN THE FREQUENCY SPECTRUM AT WHICH INSERTION LOSSES (AS A FUNCTION OF FREQUENCY) UNDER FULL LOAD ARE MEASURED,EXPRESSED IN MEGAHERTZ. 1B MODE REPLY 0 AHCKB 10LOSS AT SPECIFIED FREQUENCY IN DECIBELS,INSERTION,MINIMUM,FULL LOAD FULL LOAD MINIMUM INSERTION LOSS AT SPECIFIED FREQUENCY IN DECIBELS THE LEAST PERMISSIBLE VALUES FOR ATTENUATION OF SPURIOUS OR UNWANTED SIGNALS AT DESIGNATED POINTS IN THE FREQUENCY SPECTRUM,EXPRESSED IN DECIBELS. 1B MODE REPLY 0 AHCLJ /D/ 10CURRENT RATING,DC,CONTACT MAXIMUM LAMP LOAD CONTACT MAXIMUM LAMP LOAD DC CURRENT RATING THE GREATEST VALUE OF DIRECT CURRENT AT WHICH THE CONTACT(S) IS RATED TO MAKE OR BREAK WITH A LAMP LOAD. 1D AND 1B MODE REPLY11AC30 AHCMD /D/ 09MATERIAL,ABRASIVE ABRASIVE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ABRASIVE IS FABRICATED,EXCLUDING ANY BACKING MATERIAL,BINDER,MIX,OR LUBRICANT. SELECT REPLY CODE 10AD09 AHCNA 03DESIGNATOR,SIZE,SCREEN GRIT SCREEN GRIT SIZE DESIGNATOR A DESIGNATION INDICATING THE RATED SIZE OF THE INDIVIDUAL PARTICLES,SOMETIMES EXPRESSED AS A MESH SIZE. 1A MODE REPLY 0 AHCPD 18TYPE,DISK,ABRASIVE ABRASIVE DISK TYPE INDICATES THE TYPE OF DISK BY THE SHAPE ARRANGEMENT OF THE COATED ABRASIVE FORMED AS A RESULT OF DIE CUTTING. SELECT REPLY CODE 10AF19 AHCQA 12QUANTITY,SLOT,ABRASIVE DISK ABRASIVE DISK SLOT QUANTITY THE NUMBER OF DIE CUT SLOTS ON THE OUTER CIRCUMFERENCE OF THE ABRASIVE DISK. 1A MODE REPLY 0 AHCRJ 04LENGTH,SLOT,ABRASIVE DISK ABRASIVE DISK SLOT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ABRASIVE DISK SLOT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AHCSA 03DESIGNATOR,STRUCTURE,ABRASIVE GRAIN ABRASIVE GRAIN STRUCTURE DESIGNATOR THE NUMBER OR SYMBOL DESIGNATING THE STRUCTURE OR GRAIN SPACING WHICH IS DETERMINED BY THE PROPORTION AND ARRANGEMENT OF THE ABRASIVE AND BOND. 1A MODE REPLY 0 AHCTD /D/ 03DESIGNATION,CONCENTRATION,ABRASIVE DIAMOND POWDER ABRASIVE DIAMOND POWDER CONCENTRATION DESIGNATION A DESIGNATION OF THE GENERAL RELATIVE WEIGHT OF THE DIAMOND POWDER IN RELATION TO THE TOTAL WEIGHT OF THE COMPOUND. SELECT REPLY CODE 10AF07 AHCUA 03DESIGNATION,SIZE,METALLIC WOOL METALLIC WOOL SIZE DESIGNATION A DESIGNATION OF THE METALLIC WOOL STRAND OR FILAMENT SIZE. 1A MODE REPLY 0 AHCVD /D/ 09MATERIAL,BACKING BACKING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BACKING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH THE USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AHCWA 10WEIGHT IN LB PER REAM,BACKING,PAPER PAPER BACKING WEIGHT IN LB PER REAM THE MEASURED WEIGHT OF THE PAPER BACKING;I.E.,THE WEIGHT IN POUNDS OF 480 SHEETS,EACH MEASURING 24 X 36 INCHES. 1A MODE REPLY 0 AHCXD /D/ 07BACKING,ADHESIVE ADHESIVE BACKING AN INDICATION OF WHETHER OR NOT AN ADHESIVE BACKING IS INCLUDED. SELECT REPLY CODE 10AA49 AHCYD 18TYPE,COATING,ABRASIVE,BACKING BACKING ABRASIVE COATING TYPE INDICATES THE TYPE OF ABRASIVE COATING UTILIZED BY THE SPACING /WITH OR WITHOUT VOIDS/ OF THE MINERAL ABRASIVE GRAINS APPLIED TO THE BACKING MATERIAL. SELECT REPLY CODE 10AE91 AHCZA /D/ 16STYLE,WHEEL WHEEL STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE WHEEL. 1A MODE REPLY 0 AHDAJ 04THICKNESS,HOLE HOLE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHDBJ 04DIAMETER,FLAT,OUTSIDE OUTSIDE FLAT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHDCJ 04DIAMETER,FLAT,INSIDE INSIDE FLAT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHDDJ 04DEPTH,RELIEF RELIEF DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHDEJ 04WIDTH,EDGE EDGE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN EDGE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AHDFJ 04THICKNESS,WALL,GRINDING FACE GRINDING FACE WALL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHDGJ 04THICKNESS,USABLE USABLE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHDHJ 04LENGTH,PROTRUSION,STUD STUD PROTRUSION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE STUD THAT EXTENDS ABOVE THE BASE OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 AHDJJ 04DIAMETER,CIRCLE,BOLT,FIRST FIRST BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHDKJ 04DIAMETER,CIRCLE,BOLT,SECOND SECOND BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHDLJ /D/ 04DIAMETER,CIRCLE,BOLT,THIRD THIRD BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHDMJ /D/ 04DIAMETER,CIRCLE,BOLT,FOURTH FOURTH BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHDNJ /D/ 04DIAMETER,CIRCLE,BOLT,FIFTH FIFTH BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHDPJ 04DIAMETER,HOLE,BOLT CIRCLE BOLT CIRCLE HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT CIRCLE HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AHDQJ 04DIAMETER,SPINDLE SPINDLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SPINDLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AHDRJ 04LENGTH,SPINDLE SPINDLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SPINDLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AHDSJ 04THREAD LENGTH,SPINDLE SPINDLE THREAD LENGTH A MEASUREMENT OF THE EXTENT OF COMPLETE /FULL/ THREADS OF THE SPINDLE ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS. 2D AND 1B MODE REPLY21AA051AC20 AHDTA /D/ 16STYLE,STONE STONE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE STONE. 1A MODE REPLY 0 AHDUA /D/ 16STYLE,BRICK BRICK STYLE THE STYLE DESIGNATION INDICATING THE CONFIGUATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BRICK. 1A MODE REPLY 0 AHDVJ 04THICKNESS,EDGE,THIN THIN EDGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHDWJ 04THICKNESS,END,THIN THIN END THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHDXJ 10DENSITY AND COLOR,PRINTING,RESOLUTION RESOLUTION PRINTING DENSITY AND COLOR INDICATES THE NUMBER OF PRINTED DOTS THE ITEM CAN PRINT ON A RATED AREA AND THE COLOR. 3D AND 1B MODE REPLY32AB491AA992AG38 AHDYD 03DESIGNATION,GRADE,ABRASIVE BOND ABRASIVE BOND GRADE DESIGNATION A DESIGNATION INDICATING THE RELATIVE STRENGTH /HOLDING POWER/ OF THE BOND WHICH HOLDS THE ABRASIVE GRAINS IN PLACE. SELECT REPLY CODE 10AF20 AHDZD /D/ 07FEATURE,IMPREGNATION,OIL OIL IMPREGNATION FEATURE AN INDICATION OF WHETHER OR NOT AN OIL IMPREGNATION FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AHEAD 03DESIGNATION,HARDNESS,NATURAL,MATERIAL MATERIAL NATURAL HARDNESS DESIGNATION A DESIGNATION INDICATING THE NATURAL HARDNESS OF THE MATERIAL. SELECT REPLY CODE 10AF21 AHEBD /D/ 07MOUNTED,CASE CASE MOUNTED AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES A PERMANENT MOUNTING BOX-LIKE CONTAINER. SELECT REPLY CODE 10AA49 AHECD /D/ 07COVER,CASE,REMOVABLE REMOVABLE CASE COVER AN INDICATION OF WHETHER OR NOT A REMOVABLE CASE COVER IS INCLUDED. SELECT REPLY CODE 10AA49 AHEDJ A10WEIGHT,COMPOUND COMPOUND WEIGHT A RELATIVE MEASURE OF THE MASS OF THE COMPOUND TO ITS DENSITY. 1D AND 1A MODE REPLY12AB16 AHEED 11METHOD,APPLICATION APPLICATION METHOD THE MEANS BY WHICH THE ELEMENT,COMPOUND,MIXTURE,OR THE LIKE,IS APPLIED. SELECT REPLY CODE 10AF22 AHEFD /D/ 14SHAPE,END END SHAPE THE PHYSICAL CONFIGURATION OF THE END/S/ OF THE ITEM. SELECT REPLY CODE 10AD07 AHEGJ 04DIAMETER,HOLE,PILOT PILOT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PILOT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AHEHD /D/ 18TYPE,LUBRICANT,ABRASIVE ABRASIVE LUBRICANT TYPE INDICATES THE TYPE OF LUBRICANT USED TO BLEND THE ABRASIVE FOR USE. SELECT REPLY CODE 10AB75 AHEJD /D/ 18TYPE,HEADBAND HEADBAND TYPE INDICATES THE TYPE OF PHYSICAL FEATURE WHICH MECHANICALLY CONNECTS AND POSITIONS EARPHONE(S) OR OTHER SOUND CONDUCTORS OVER OR ADJACENT TO THE EAR(S) OF THE WEARER. SELECT REPLY CODE 10AF23 AHEKD /D/ 09MATERIAL,COVERING,HEADBAND HEADBAND COVERING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HEADBAND COVERING IS FABRICATED. SELECT REPLY CODE 10AD09 AHELD /D/ 09MATERIAL,PADDING,HEADBAND HEADBAND PADDING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HEADBAND PADDING IS FABRICATED. SELECT REPLY CODE 10AD09 AHEMJ 04LENGTH,CORD,HEADSET HEADSET CORD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE HEADSET CORD,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AHEND /D/ 19FACILITY,MOUNTING,MICROPHONE MICROPHONE MOUNTING FACILITY THE MEANS PROVIDED TO MOUNT OR OTHERWISE ACCOMMODATE A MICROPHONE. SELECT REPLY CODE 10AF24 AHEPD 18TYPE,HELMET,ACCOMMODATED ACCOMMODATED HELMET TYPE INDICATES THE TYPE OF HELMET ACCOMMODATED BY THE ITEM. SELECT REPLY CODE 10AF25 AHEQD 18TYPE,ELEMENT,EARPHONE EARPHONE ELEMENT TYPE INDICATES THE TYPE OF EARPHONE ELEMENT AS DETERMINED BY ITS CONSTRUCTION AND METHOD OF OPERATION. SELECT REPLY CODE 10AE76 AHERD 19CAPABILITY,MONITOR,CHANNEL CHANNEL MONITOR CAPABILITY THE DESIGNED ABILITY OF THE ITEM TO MONITOR CHANNELS. SELECT REPLY CODE 10AF26 AHESA 12QUANTITY,EARPHONE EARPHONE QUANTITY THE NUMBER OF EARPHONES PROVIDED ON THE ITEM. 1A MODE REPLY 0 AHETA 12QUANTITY,ACCOMMODATION,EARPHONE EARPHONE ACCOMMODATION QUANTITY THE NUMBER OF EARPHONES ACCOMMODATED BY THE ITEM. 1A MODE REPLY 0 AHEUD /D/ 09MATERIAL,CAP,EARPHONE EARPHONE CAP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE EARPHONE CAP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AHEVD /D/ 09MATERIAL,SHELL,EARPHONE EARPHONE SHELL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE EARPHONE SHELL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC CSPT IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AHEWD /D/ 09MATERIAL,CUSHION,EARPHONE EARPHONE CUSHION MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE EARPHONE CUSHION IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AHEXD 19ARRANGEMENT,INTERCONNECTION,EARPHONE EARPHONE INTERCONNECTION ARRANGEMENT THE DESIGNATION THAT IDENTIFIES THE ELECTRICAL CIRCUIT ARRANGEMENT THROUGH WHICH AN INCOMING SIGNAL IS CONDUCTED TO THE EARPHONE/S/. SELECT REPLY CODE 10AD62 AHEYD /D/ 11METHOD,MOUNTING,EARPHONE EARPHONE MOUNTING METHOD THE MEANS OF ATTACHING THE EARPHONE TO THE ITEM. PLEASE USE MRC BKSY IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB89 AHEZJ 04DEPTH,OVERALL,EARPHONE EARPHONE OVERALL DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHFAJ 04DEPTH,EARPHONE,ELEMENT EARPHONE ELEMENT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHFBJ /D/ 04HEIGHT,EARPHONE,ELEMENT ELEMENT EARPHONE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AHFCJ /D/ 04WIDTH,EARPHONE,ELEMENT ELEMENT EARPHONE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHFDJ 04DIAMETER,OUTSIDE,EARPHONE CUSHION EARPHONE CUSHION OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHFEJ 04DIAMETER,INSIDE,EARPHONE CUSHION EARPHONE CUSHION INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHFFJ 04THICKNESS,CUSHION,EARPHONE EARPHONE CUSHION THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHFGJ 04HEIGHT,OUTSIDE,EARPHONE CUSHION EARPHONE CUSHION OUTSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AHFHJ 04HEIGHT,INSIDE,EARPHONE CUSHION EARPHONE CUSHION INSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AHFJJ 04WIDTH,OUTSIDE,EARPHONE CUSHION EARPHONE CUSHION OUTSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHFKJ 04WIDTH,INSIDE,EARPHONE CUSHION EARPHONE CUSHION INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHFLJ 04HEIGHT,OVERALL,HEADSET HEADSET OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AHFMJ 04WIDTH,OVERALL,HEADSET HEADSET OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHFNJ 04DEPTH,OVERALL,HEADSET HEADSET OVERALL DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHFPD 18TYPE,DEVICE,IMPEDANCE MATCHING IMPEDANCE MATCHING DEVICE TYPE INDICATES THE TYPE OF DEVICE USED TO MATCH THE IMPEDANCE OF THE ITEM TO THE IMPEDANCE OF THE OUTPUT CIRCUIT. SELECT REPLY CODE 10AF27 AHFQD /D/ 08LOCATION,DEVICE,IMPEDANCE MATCHING IMPEDANCE MATCHING DEVICE LOCATION INDICATES THE LOCATION OF THE IMPEDANCE MATCHING DEVICE ON THE ITEM. SELECT REPLY CODE 10AE46 AHFRB 10FREQUENCY IN HERTZ,REFERENCE REFERENCE FREQUENCY IN HERTZ THE POINT IN THE RESPONSE FREQUENCY SPECTRUM WHERE THE MAXIMUM AUDITORY OUTPUT OF A FIXED INPUT SIGNAL OCCURS AND FROM WHICH ATTENUATION,IMPEDANCE,AND RESPONSE BANDWIDTHS ARE DETERMINED,EXPRESSED IN HERTZ. 1B MODE REPLY 0 AHFSD 10RATING,REFERENCE,SENSITIVITY,ACOUSTIC ACOUSTIC SENSITIVITY REFERENCE RATING THE ELECTRICAL INPUT POWER AND SOUND PRESSURE OUTPUT RATINGS WHICH ARE USED AS A BASE REFERENCE FOR THE MEASUREMENT OF THE SENSITIVITY OF AN ITEM. SELECT REPLY CODE 10AF28 AHFTD /D/ 07SHIELDING,MAGNETIC MAGNETIC SHIELDING AN INDICATION OF WHETHER OR NOT A MAGNETIC SHIELD IS INCLUDED. SELECT REPLY CODE 10AA49 AHFUD 08LOCATION,TERMINATION,HEADSET CONNECTING CORD HEADSET CONNECTING CORD TERMINATION LOCATION INDICATES THE LOCATION OF THE INPUT CONNECTION HEADSET WITH RESPECT TO THE WEARER. SELECT REPLY CODE 10AF29 AHFVD /D/ 07SHIELDED,CORD,EXTENSION EXTENSION CORD SHIELDED AN INDICATION OF WHETHER OR NOT THE EXTENSION CORD IS SHIELDED. SELECT REPLY CODE 10AA89 AHFWA /D/ 12QUANTITY,CONDUCTOR,EXTENSION CORD EXTENSION CORD CONDUCTOR QUANTITY THE TOTAL NUMBER OF INSULATED WIRES,SHIELDED OR UNSHIELDED WHICH MAKE UP THE CORD. 1A MODE REPLY 0 AHFXD /D/ 18TYPE,TERMINAL,EXTENSION CORD EXTENSION CORD TERMINAL TYPE INDICATES THE TYPE OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE EXTENSION CORD. SELECT REPLY CODE 10AA58 AHFYJ 04LENGTH,CORD,EXTENSION EXTENSION CORD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE EXTENSION CORD. 1D AND 1B MODE REPLY11AA05 AHFZD /D/ 18TYPE,TERMINAL,SIGNAL INPUT SIGNAL INPUT TERMINAL TYPE INDICATES THE TYPE OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE SIGNAL INPUT. PLEASE USE MRC AHBM IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA58 AHGAA 19IDENTIFICATION,CORD,ELECTRICAL ELECTRICAL CORD IDENTIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS IDENTIFICATION NUMBER OR SYMBOL USED TO IDENTIFY THE ELECTRICAL CORD. 1A MODE REPLY 0 AHGBA 19CODE,MANUFACTURER,ELECTRICAL CORD ELECTRICAL CORD MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE ELECTRICAL CORD. 1A MODE REPLY 0 AHGCJ 10SPEED AND COLOR,PRINT PRINT SPEED AND COLOR DESIGNATES THE PRINTING RATE OF THE ITEM AND THE COLOR. 2D AND 1B MODE REPLY22AG383AB44 AHGDJ 04HEIGHT,FLANGE FLANGE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A FLANGE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AHGEJ 04DEPTH,SLOT,MOUNTING MOUNTING SLOT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHGFA 12QUANTITY,LAMPHOLDER LAMPHOLDER QUANTITY THE NUMBER OF LAMPHOLDERS INCLUDED ON THE ITEM. 1A MODE REPLY 0 AHGGA 19CODE,MANUFACTURER,LAMPHOLDER LAMPHOLDER MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE LAMPHOLDER. 1A MODE REPLY 0 AHGHA 19NUMBER,PART,LAMPHOLDER MANUFACTURER LAMPHOLDER MANUFACTURER PART NUMBER THE IDENTIFYING PART NUMBER ASSIGNED TO THE LAMPHOLDER BY THE MANUFACTURER. 1A MODE REPLY 0 AHGJD 18TYPE,FEATURE,MOUNTING MOUNTING FEATURE TYPE INDICATES THE TYPE OF FEATURE USED TO MOUNT THE ITEM. SELECT REPLY CODE 10AF30 AHGKJ 04WIDTH,CLIP CLIP WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHGLA 19CODE,MANUFACTURER,MOUNTING STRIP MOUNTING STRIP MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE MOUNTING STRIP. 1A MODE REPLY 0 AHGMA 19NUMBER,PART,MOUNTING STRIP MANUFACTURER MOUNTING STRIP MANUFACTURER PART NUMBER THE IDENTIFYING PART NUMBER ASSIGNED TO THE MOUNTING STRIP BY THE MANUFACTURER. 1A MODE REPLY 0 AHGNJ 04HEIGHT,APERTURE APERTURE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AHGPD /D/ 18TYPE,ANCHOR ANCHOR TYPE INDICATES THE TYPE OF ANCHOR PROVIDED. SELECT REPLY CODE 10AF31 AHGQD 18TYPE,CLAMP CLAMP TYPE INDICATES THE TYPE OF CLAMP PROVIDED. SELECT REPLY CODE 10AF32 AHGRD /D/ 07FEATURE,INSULATED INSULATED FEATURE AN INDICATION OF WHETHER OR NOT AN INSULATED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AHGSJ /D/ 04LENGTH FROM EYE CENTER TO FIRST BEAD END LENGTH FROM EYE CENTER TO FIRST BEAD END NONE. 2D AND 1B MODE REPLY21AA051AC20 AHGTD 18TYPE,HOOK HOOK TYPE INDICATES THE TYPE OF HOOK PROVIDED ON THE ITEM. SELECT REPLY CODE 10AF33 AHGUD 18TYPE,PROTECTOR PROTECTOR TYPE INDICATES THE TYPE OF PROTECTOR PROVIDED. SELECT REPLY CODE 10AF34 AHGVD /D/ 18TYPE,EXPANSION EXPANSION TYPE INDICATES THE TYPE OF EXPANSION PROVIDED ON THE ITEM. SELECT REPLY CODE 10AF35 AHGWD 18TYPE,ROD ROD TYPE INDICATES THE TYPE OF ROD PROVIDED. SELECT REPLY CODE 10AD15 AHGXJ /D/ 13THREAD DIAMETER,SHANK SHANK THREAD DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHGYJ /D/ 10MEASURE,SQUARE SQUARE MEASURE A MEASUREMENT OF AREA TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH OF ANY ITEM AND RENDERED IN SQUARE UNITS. 2D AND 1B MODE REPLY21AA051AC20 AHGZL 16STYLE,END,UPPER UPPER END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE UPPER END. 1L MODE REPLY 0 AHHAL 16STYLE,END,LOWER LOWER END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LOWER END. 1L MODE REPLY 0 AHHBJ 04LENGTH,INSIDE,SLEEVE SLEEVE INSIDE LENGTH A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF THE SLEEVE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AHHCJ 04DIAMETER,BOLT,ADJUSTMENT ADJUSTMENT BOLT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ADJUSTMENT BOLT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AHHDJ /D/ 04DIAMETER,END,BALL BALL END DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHHEJ 04WIDTH,TONGUE TONGUE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A TONGUE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AHHFJ 04THICKNESS,TONGUE TONGUE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A TONGUE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AHHGJ 04DISTANCE BETWEEN LEGS DISTANCE BETWEEN LEGS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHHHJ 04LENGTH FROM PINHOLE CENTER TO END LENGTH FROM PINHOLE CENTER TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AHHJJ /D/ 04HEIGHT,OVERALL,LEG LEG OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AHHKJ 04RADIUS,END,FLAT FLAT END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHHLJ 04RADIUS,END,ELEVATED ELEVATED END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHHMJ 04LENGTH,HOLE CENTER TO ELEVATED END HOLE CENTER TO ELEVATED END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHHNJ /D/ 04LENGTH,HOLE,FLAT END FLAT END HOLE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHHPJ /D/ 04WIDTH,HOLE,FLAT END FLAT END HOLE WIDTH NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 2D AND 1B MODE REPLY21AA051AC20 AHHQJ /D/ 04RADIUS,HOLE,FLAT END FLAT END HOLE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHHRD /D/ 07RING,DEE DEE RING AN INDICATION OF WHETHER OR NOT A DEE RING IS INCLUDED. SELECT REPLY CODE 10AA49 AHHSA 12QUANTITY,BOLT BOLT QUANTITY THE NUMBER OF BOLTS PROVIDED. 1A MODE REPLY 0 AHHTD 05DIRECTION,LAY,ACCOMMODATED ACCOMMODATED LAY DIRECTION THE DIRECTION OF LAY WHICH THE ITEM IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AA38 AHHUA 12QUANTITY FOR WHICH DESIGNED,STRAND STRAND QUANTITY FOR WHICH DESIGNED THE NUMBER OF STRANDS FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 AHHVD /D/ 07SURFACE,GROOVED GROOVED SURFACE AN INDICATION OF WHETHER OR NOT A GROOVE IS INCLUDED ON THE SURFACE. SELECT REPLY CODE 10AA49 AHHWD /D/ 07HOLE,RING RING HOLE AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A RING HOLE. SELECT REPLY CODE 10AB22 AHHXJ /D/T05DIRECTION AND RANGE,SCALE SCALE DIRECTION AND RANGE THE ORDER OF THE NUMERIC SCALE MARKINGS OF THE DIAL. 1D AND 1F MODE REPLY11AB50 AHHYJ /D/ 04DISTANCE FROM POINT TO HOOK DISTANCE FROM POINT TO HOOK THE DISTANCE PERPENDICULAR TO THE POINT AXIS FROM THE POINT TIP TO THE HOOK. 2D AND 1B MODE REPLY21AA051AC20 AHHZJ 04LENGTH,PROVISION,WIRING WIRING PROVISION LENGTH THE MEASUREMENT OF EACH WIRING PROVISION OF AN ITEM TAKEN FROM THE BODY TO THE ENDS OF THE WIRING PROVISION,INCLUDING ANY TERMINATIONS. 2D AND 1B MODE REPLY21AA051AC20 AHJAD /D/ 11METHOD,CONSTRUCTION,ANCHOR CHAIN GUARD ANCHOR CHAIN GUARD CONSTRUCTION METHOD THE MEANS BY WHICH THE ANCHOR CHAIN GUARD IS CONSTRUCTED. SELECT REPLY CODE 10AF36 AHJBJ /D/ 04LENGTH,CHAMFER,LEFT CORNER,INSIDE INSIDE LEFT CORNER CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 AHJCB /D/ 04ANGLE IN DEG,CHAMFER,INSIDE LEFT CORNER INSIDE LEFT CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AHJDJ /D/ 04RADIUS,CORNER,LEFT,INSIDE INSIDE LEFT CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHJEJ /D/ 04LENGTH,CHAMFER,RIGHT CORNER,INSIDE INSIDE RIGHT CORNER CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 AHJFB /D/ 04ANGLE IN DEG,CHAMFER,INSIDE RIGHT CORNER INSIDE RIGHT CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AHJGJ /D/ 04RADIUS,CORNER,RIGHT,INSIDE INSIDE RIGHT CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHJHJ /D/ 04LENGTH,CHAMFER,LEFT CORNER,OUTSIDE OUTSIDE LEFT CORNER CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 AHJJB /D/ 04ANGLE IN DEG,CHAMFER,OUTSIDE LEFT CORNER OUTSIDE LEFT CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AHJKJ /D/ 04RADIUS,CORNER,LEFT,OUTSIDE OUTSIDE LEFT CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHJLJ /D/ 04LENGTH,CHAMFER,RIGHT CORNER,OUTSIDE OUTSIDE RIGHT CORNER CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 AHJMB /D/ 04ANGLE IN DEG,CHAMFER,OUTSIDE RIGHT CORNER OUTSIDE RIGHT CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AHJNJ /D/ 04RADIUS,CORNER,RIGHT,OUTSIDE OUTSIDE RIGHT CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHJPJ /D/ 04LENGTH,CHAMFER,OUTSIDE RIGHT CORNER,LEFT FLANGE LEFT FLANGE OUTSIDE RIGHT CORNER CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 AHJQB /D/ 04ANGLE IN DEG,CORNER,RIGHT,LEFT FLANGE OUTSIDE LEFT FLANGE OUTSIDE RIGHT CORNER ANGLE IN DEG NONE. 1B MODE REPLY 0 AHJRJ /D/ 04RADIUS,CORNER,LEFT FLANGE OUTSIDE RIGHT LEFT FLANGE OUTSIDE RIGHT CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHJSJ /D/ 04RADIUS,CORNER,LEFT FLANGE BODY LEFT FLANGE BODY CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHJTJ /D/ 04WIDTH,GROOVE,RELIEF,LEFT FLANGE BODY CORNER LEFT FLANGE BODY CORNER RELIEF GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHJUJ /D/ 04DEPTH,GROOVE,RELIEF,LEFT FLANGE BODY CORNER LEFT FLANGE BODY CORNER RELIEF GROOVE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHJVJ /D/ 04RADIUS,GROOVE,RELIEF,LEFT FLANGE BODY CORNER LEFT FLANGE BODY CORNER RELIEF GROOVE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHJWJ /D/ 04WIDTH,UNDERCUT,LEFT FLANGE BODY CORNER LEFT FLANGE BODY CORNER UNDERCUT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHJXJ /D/ 04DEPTH,UNDERCUT,CORNER,LEFT FLANGE BODY LEFT FLANGE BODY CORNER UNDERCUT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHJYJ /D/ 04RADIUS,UNDERCUT,LEFT FLANGE BODY CORNER LEFT FLANGE BODY CORNER UNDERCUT RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHJZJ /D/ 04LENGTH,CHAMFER,OUTSIDE LEFT CORNER,RIGHT FLANGE RIGHT FLANGE OUTSIDE LEFT CORNER CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 AHKAB /D/ 04ANGLE IN DEG,CHAMFER,LEFT CORNER,RIGHT FLANGE OUTSIDE RIGHT FLANGE OUTSIDE LEFT CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AHKBJ /D/ 04RADIUS,CORNER,RIGHT FLANGE OUTSIDE LEFT RIGHT FLANGE OUTSIDE LEFT CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKCJ /D/ 04RADIUS,CORNER,RIGHT FLANGE BODY RIGHT FLANGE BODY CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKDJ /D/ 04WIDTH,GROOVE,RELIEF,RIGHT FLANGE BODY CORNER RIGHT FLANGE BODY CORNER RELIEF GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKEJ /D/ 04DEPTH,GROOVE,RELIEF,RIGHT FLANGE BODY CORNER RIGHT FLANGE BODY CORNER RELIEF GROOVE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKFJ /D/ 04RADIUS,GROOVE,RELIEF,RIGHT FLANGE BODY CORNER RIGHT FLANGE BODY CORNER RELIEF GROOVE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKGJ /D/ 04WIDTH,UNDERCUT,RIGHT FLANGE BODY CORNER RIGHT FLANGE BODY CORNER UNDERCUT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKHJ /D/ 04DEPTH,UNDERCUT,CORNER,RIGHT FLANGE BODY RIGHT FLANGE BODY CORNER UNDERCUT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKJJ /D/ 04RADIUS,UNDERCUT,RIGHT FLANGE BODY CORNER RIGHT FLANGE BODY CORNER UNDERCUT RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKKJ /D/ 04RADIUS,CORNER,CENTER FLANGE LEFT BODY CENTER FLANGE LEFT BODY CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKLJ /D/ 04WIDTH,GROOVE,RELIEF,LEFT BODY CORNER CENTER FLANGE LEFT BODY CORNER CENTER FLANGE RELIEF GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKMJ /D/ 04DEPTH,GROOVE,RELIEF,CENTER FLANGE LEFT BODY CORNER CENTER FLANGE LEFT BODY CORNER RELIEF GROOVE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKNJ /D/ 04RADIUS,GROOVE,RELIEF,CENTER FLANGE LEFT BODY CORNER CENTER FLANGE LEFT BODY CORNER RELIEF GROOVE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKPJ /D/ 04WIDTH,UNDERCUT,CENTER FLANGE LEFT BODY CORNER CENTER FLANGE LEFT BODY CORNER UNDERCUT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKQJ /D/ 04DEPTH,UNDERCUT,CORNER,CENTER FLANGE LEFT BODY CENTER FLANGE LEFT BODY CORNER UNDERCUT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKRJ /D/ 04RADIUS,UNDERCUT,CENTER FLANGE LEFT BODY CORNER CENTER FLANGE LEFT BODY CORNER UNDERCUT RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKSJ /D/ 04RADIUS,CORNER,CENTER FLANGE RIGHT BODY CENTER FLANGE RIGHT BODY CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKTJ /D/ 04WIDTH,GROOVE,RELIEF,CENTER FLANGE RIGHT BODY CORNER CENTER FLANGE RIGHT BODY CORNER RELIEF GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKUJ /D/ 04DEPTH,GROOVE RELIEF,CENTER FLANGE RIGHT BODY CORNER CENTER FLANGE RIGHT BODY CORNER GROOVE RELIEF DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKVJ /D/ 04RADIUS,GROOVE,RELIEF,CENTER FLANGE RIGHT BODY CORNER CENTER FLANGE RIGHT BODY CORNER RELIEF GROOVE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKWJ /D/ 04WIDTH,UNDERCUT,CENTER FLANGE RIGHT BODY CORNER CENTER FLANGE RIGHT BODY CORNER UNDERCUT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKXJ /D/ 04DEPTH,UNDERCUT,CORNER,CENTER FLANGE RIGHT BODY CENTER FLANGE RIGHT BODY CORNER UNDERCUT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKYJ /D/ 04RADIUS,UNDERCUT,CENTER FLANGE RIGHT BODY CORNER CENTER FLANGE RIGHT BODY CORNER UNDERCUT RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHKZJ /D/ 04LENGTH,CHAMFER,OUTSIDE LEFT CORNER,CENTER FLANGE CENTER FLANGE OUTSIDE LEFT CORNER CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 AHLAB /D/ 04ANGLE IN DEG,CHAMFER,CENTER FLANGE OUTSIDE LEFT CORNER CENTER FLANGE OUTSIDE LEFT CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AHLBJ /D/ 04RADIUS,CORNER,CENTER FLANGE OUTSIDE LEFT CENTER FLANGE OUTSIDE LEFT CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLCJ /D/ 04LENGTH,CHAMFER,OUTSIDE RIGHT CORNER,CENTER FLANGE CENTER FLANGE OUTSIDE RIGHT CORNER CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 AHLDB /D/ 04ANGLE IN DEG,CORNER,RIGHT,CENTER FLANGE OUTSIDE CENTER FLANGE OUTSIDE RIGHT CORNER ANGLE IN DEG NONE. 1B MODE REPLY 0 AHLEJ /D/ 04RADIUS,CORNER,CENTER FLANGE OUTSIDE RIGHT CENTER FLANGE OUTSIDE RIGHT CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLFJ 04WIDTH,LEG,SECOND SECOND LEG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLGJ 04RADIUS,CORNER,SECOND LEG SECOND LEG CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLHJ 04WIDTH,END,SECOND LEG SECOND LEG END WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLJJ 04DIAMETER,LEG,SECOND SECOND LEG DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLKJ 04DIAMETER,HOLE,FIRST LEG FIRST LEG HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLLJ 04LENGTH,SLOT,FIRST LEG FIRST LEG SLOT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLMJ 04WIDTH,SLOT,FIRST LEG FIRST LEG SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLNJ 04DIAMETER,HOLE,SECOND LEG SECOND LEG HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLPJ 04DISTANCE BETWEEN HOLE CENTERS ALONG WIDTH,LEG,SECOND SECOND LEG DISTANCE BETWEEN HOLE CENTERS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLQJ 04DISTANCE BETWEEN UPPER HOLE CENTERS ALONG WIDTH,LEG,SECOND SECOND LEG DISTANCE BETWEEN UPPER HOLE CENTERS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLRJ 04DISTANCE BETWEEN LOWER HOLE CENTERS ALONG WIDTH,LEG,SECOND SECOND LEG DISTANCE BETWEEN LOWER HOLE CENTERS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLSJ 04DISTANCE BETWEEN HOLE CENTERS ALONG LENGTH,LEG,SECOND SECOND LEG DISTANCE BETWEEN HOLE CENTERS ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLTJ 04DISTANCE BETWEEN FIRST AND SECOND HOLE CENTERS ALONG WIDTH,LEG,SECOND SECOND LEG DISTANCE BETWEEN FIRST AND SECOND HOLE CENTERS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLUJ 04DISTANCE BETWEEN SECOND AND THIRD HOLE CENTERS ALONG WIDTH,LEG,SECOND SECOND LEG DISTANCE BETWEEN SECOND AND THIRD HOLE CENTERS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLVJ 04DISTANCE FROM EDGE TO HOLE CENTER ALONG WIDTH,LEG,SECOND SECOND LEG DISTANCE FROM EDGE TO HOLE CENTER ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLWJ 04DISTANCE FROM EDGE TO HOLE CENTER ALONG LENGTH,LEG,SECOND SECOND LEG DISTANCE FROM EDGE TO HOLE CENTER ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLXJ 04DISTANCE BETWEEN FIRST AND SECOND HOLE CENTERS ALONG LENGTH,LEG,SECOND SECOND LEG DISTANCE BETWEEN FIRST AND SECOND HOLE CENTERS ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLYJ 04DISTANCE BETWEEN SECOND AND THIRD HOLE CENTERS ALONG LENGTH,LEG,SECOND SECOND LEG DISTANCE BETWEEN SECOND AND THIRD HOLE CENTERS ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHLZJ 04LENGTH,SLOT,SECOND LEG SECOND LEG SLOT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHMAJ 04WIDTH,SLOT,SECOND LEG SECOND LEG SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHMBJ 04DISTANCE BETWEEN THIRD AND FOURTH HOLE CENTERS ALONG WIDTH,SECOND LEG SECOND LEG DISTANCE BETWEEN THIRD AND FOURTH HOLE CENTERS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHMCJ 04RADIUS,CENTER,SECOND LEG HOLE SECOND LEG HOLE CENTER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHMDB /D/ 04ANGLE BETWEEN EDGE AND FIRST HOLE CENTER IN DEG,LEG,SECOND SECOND LEG ANGLE BETWEEN EDGE AND FIRST HOLE CENTER IN DEG NONE. 1B MODE REPLY 0 AHMEB /D/ 04ANGLE BETWEEN EDGE AND SECOND HOLE CENTER IN DEG,LEG,SECOND SECOND LEG ANGLE BETWEEN EDGE AND SECOND HOLE CENTER IN DEG NONE. 1B MODE REPLY 0 AHMFJ 04DIAMETER,HOLE,HANDLE HANDLE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHMGJ 04DIAMETER,OUTSIDE,LARGE END LARGE END OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGE END,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AHMHJ 04DIAMETER,OUTSIDE,SMALL END SMALL END OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALL END,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AHMJJ 04DIAMETER,OUTSIDE,WRENCHING END WRENCHING END OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHMKJ 04DIAMETER,OUTSIDE,DRIVE END DRIVE END OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHMLJ 04THICKNESS,HEAD HEAD THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE HEAD, IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AHMMJ 04WIDTH,LUG LUG WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE LUG,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AHMNJ 04THICKNESS,LUG LUG THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHMPJ 04LENGTH,ARM,LONG LONG ARM LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHMQJ 10LOAD,STACKING STACKING LOAD THE MAXIMUM LOAD THAT CAN BE POSITIONED ON THE ITEM IN THE FORM OF STACKED ITEMS OF THE SAME TYPE. 1D AND 1B MODE REPLY12AG67 AHMRJ /D/ 04HEIGHT,STACKING STACKING HEIGHT A MEASUREMENT FROM THE BOTTOM OF THE ITEM TO THE SUPPORT POINT OF THE NEXT STACKED ITEM OF THE SAME TYPE, IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AHMSJ 04DIAMETER,INSIDE,UPPER LOOP UPPER LOOP INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHMTJ 04DIAMETER,INSIDE,LOWER LOOP LOWER LOOP INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHMUJ /D/ 04LENGTH,RETURN,UPPER LOOP UPPER LOOP RETURN LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHMVJ /D/ 04LENGTH,RETURN,LOWER LOOP LOWER LOOP RETURN LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHMWJ /D/ 04WIDTH,OPENING,UPPER LOOP UPPER LOOP OPENING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHMXJ /D/ 10AREA,HOLDING,OPEN ANCHOR OPEN ANCHOR HOLDING AREA A MEASUREMENT OF THE HOLDING AREA WHEN THE ANCHOR IS IN AN OPEN POSITION. 2D AND 1B MODE REPLY21AC511AC20 AHMYJ 04DIAMETER,STOCK,MAIN LINK MAIN LINK STOCK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHMZJ 04LENGTH,INSIDE,MAIN LINK MAIN LINK INSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHNAJ 04LENGTH,INSIDE,HINGE LINK HINGE LINK INSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHNBJ /D/ 04DIAMETER,INSIDE,CLOSED HOOK CLOSED HOOK INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHNCL 16STYLE,CONNECTION CONNECTION STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CONNECTION. 1L MODE REPLY 0 AHNDJ 04LENGTH,OPENING,CLEAR CLEAR OPENING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CLEAR OPENING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AHNED 19RELATIONSHIP,CONNECTION TO BODY CONNECTION TO BODY RELATIONSHIP AN INDICATION OF THE RELATIONSHIP OF THE CONNECTION TO THE BODY. SELECT REPLY CODE 10AJ69 AHNFJ A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CONNECTION CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE FOR THE CONNECTION. 1D AND 1A MODE REPLY12AH06 AHNGJ /D/ 13THREAD LENGTH,CONNECTION CONNECTION THREAD LENGTH A MEASUREMENT OF THE EXTENT OF COMPLETE /FULL/ THREADS OF THE CONNECTION ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS. 2D AND 1B MODE REPLY21AA051AC20 AHNHD /D/ 07REMOVABILITY,POINT POINT REMOVABILITY AN INDICATION OF WHETHER OR NOT THE POINT/S/ IS REMOVABLE. SELECT REPLY CODE 10AC29 AHNJD 18TYPE,ATTACHMENT,END END ATTACHMENT TYPE INDICATES THE TYPE OF END ATTACHMENT INCLUDED ON THE ITEM. SELECT REPLY CODE 10AF38 AHNKJ 04DIAMETER,MATERIAL,ACCOMMODATED ACCOMMODATED MATERIAL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED MATERIAL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AHNLD /D/ 05DIRECTION,RELEASE,SAFETY THROAT CLOSURE SAFETY THROAT CLOSURE RELEASE DIRECTION THE DIRECTION THAT THE SAFETY THROAT CLOSURE MOVES TO RELEASE THE ITEM. SELECT REPLY CODE 10AC50 AHNMA 12QUANTITY ACCOMMODATED,LINE LINE QUANTITY ACCOMMODATED THE NUMBER OF LINES THAT THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 AHNNJ 04LENGTH FROM CROSS STUD,INSIDE INSIDE LENGTH FROM CROSS STUD NONE. 2D AND 1B MODE REPLY21AA051AC20 AHNPJ /D/ 04LENGTH,INSIDE,BAIL BAIL INSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHNQJ /D/ 04DIAMETER,INSIDE,BAIL BAIL INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHNRJ /D/ 04DISTANCE FROM BAIL CENTER TO SHACKLE EYE CENTER DISTANCE FROM BAIL CENTER TO SHACKLE EYE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHNSJ 04THICKNESS,END,LEG LEG END THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHNTD /D/ 07PINHOLE,FORELOCK FORELOCK PINHOLE AN INDICATION OF WHETHER OR NOT A FORELOCK PINHOLE IS INCLUDED. SELECT REPLY CODE 10AA49 AHNUD /D/ 07CLOSURE CLOSURE AN INDICATION OF WHETHER OR NOT A CLOSURE IS INCLUDED ON THE ITEM. SELECT REPLY CODE 10AA49 AHNVD 19CONDITION,END END CONDITION AN INDICATION OF THE CONDITION OF THE END. SELECT REPLY CODE 10AB68 AHNWD /D/ 07CHAIN,RETAINING RETAINING CHAIN AN INDICATION OF WHETHER OR NOT A RETAINING CHAIN IS PROVIDED. SELECT REPLY CODE 10AB22 AHNXJ 04DIAMETER,HOLE,BOLT BOLT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AHNYJ 04DIAMETER,BOLT BOLT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AHNZD /D/ 07WEDGE WEDGE AN INDICATION OF WHETHER OR NOT A WEDGE IS PROVIDED ON THE ITEM. SELECT REPLY CODE 10AB22 AHPAJ /D/ 04WIDTH,INSIDE,LINK LINK INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHPBJ /D/ 04LENGTH,INSIDE,JAW JAW INSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHPCJ /D/ 04LENGTH,INSIDE,LINK OPENING LINK OPENING INSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHPDJ /D/ 04DISTANCE BETWEEN UPPER SWIVEL CONNECTIONS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN UPPER SWIVEL CONNECTIONS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHPEJ /D/ 04DISTANCE BETWEEN LOWER SWIVEL CONNECTIONS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN LOWER SWIVEL CONNECTIONS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHPFJ 04RADIUS,INSIDE,EYE NARROW END EYE NARROW END INSIDE RADIUS NONE. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 2D AND 1B MODE REPLY21AA051AC20 AHPGJ 04RADIUS,INSIDE,EYE WIDE END EYE WIDE END INSIDE RADIUS NONE.MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 2D AND 1B MODE REPLY21AA051AC20 AHPHJ 10WEIGHT,HEAD HEAD WEIGHT A RELATIVE MEASURE OF THE MASS OF A HEAD WITH RESPECT TO ITS DENSITY. 2D AND 1B MODE REPLY22AG531AC20 AHPJJ /D/ 04THICKNESS,STOCK,JAW JAW STOCK THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHPKJ /D/ 04DIAMETER,STOCK,ATTACHING LINK ATTACHING LINK STOCK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHPLJ /D/ 04LENGTH,INSIDE,ATTACHING LINK ATTACHING LINK INSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHPMJ 04LENGTH,REACH REACH LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE REACH,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AHPND /D/ 07REMOVABILITY,LINK LINK REMOVABILITY AN INDICATION OF WHETHER OR NOT THE LINK IS REMOVABLE. SELECT REPLY CODE 10AC29 AHPPJ 04RADIUS,OUTER OUTER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHPQJ 04DISTANCE FROM HOLE CENTER TO TAPERED END DISTANCE FROM HOLE CENTER TO TAPERED END NONE. 2D AND 1B MODE REPLY21AA051AC20 AHPRJ 04HEIGHT,END,TAPERED TAPERED END HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AHPSJ 04RADIUS,INNER INNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHPTD /D/ 07HOLE,KNOCKOUT KNOCKOUT HOLE AN INDICATION OF WHETHER OR NOT A KNOCKOUT HOLE/S/ IS PROVIDED ON THE ITEM. SELECT REPLY CODE 10AB22 AHPUD /D/ 11METHOD,HOLDING,GUY GUY HOLDING METHOD THE MEANS UTILIZED TO HOLD THE GUY. SELECT REPLY CODE 10AF39 AHPVB /D/ 04ANGLE IN DEG,LEG,FIRST FIRST LEG ANGLE IN DEG NONE. 1B MODE REPLY 0 AHPWJ 04THICKNESS,LEG,FIRST FIRST LEG THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE FIRST LEG,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AHPXJ 04THICKNESS,LEG,SECOND SECOND LEG THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE SECOND LEG,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AHPYB 04ANGLE IN DEG,LEG,SECOND SECOND LEG ANGLE IN DEG NONE. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 1B MODE REPLY 0 AHPZJ 04HEIGHT,SECTION,CENTER CENTER SECTION HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AHQAJ 04WIDTH,SECTION,CENTER CENTER SECTION WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHQBJ 04THICKNESS,SECTION,CENTER CENTER SECTION THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHQCB /D/ 04ANGLE IN DEG,OFFSET OFFSET ANGLE IN DEG NONE. 1B MODE REPLY 0 AHQDJ 04DISTANCE FROM CORNER TO HINGE PIN DISTANCE FROM CORNER TO HINGE PIN NONE. 2D AND 1B MODE REPLY21AA051AC20 AHQEJ /D/ 04SIZE,SCREW,MOUNTING MOUNTING SCREW SIZE NONE. 2D AND 1B MODE REPLY21AA051AC20 AHQFJ 04LENGTH,PROJECTION PROJECTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A PROJECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AHQGJ /D/ 04DIAMETER,HOLE,WALL MOUNTING WALL MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHQHJ /D/ 04DIAMETER,HOLE,RAIL MOUNTING RAIL MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHQJJ 04DIAMETER,ROD,ACCOMMODATED ACCOMMODATED ROD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED ROD,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AHQKJ /D/ 04HEIGHT,END,LEG LEG END HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AHQLJ 04WIDTH,SECTION,TOP TOP SECTION WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHQMA /D/ 16STYLE,LEG,FIRST FIRST LEG STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FIRST LEG. 1A MODE REPLY 0 AHQNJ 04WIDTH,LEG,FIRST FIRST LEG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHQPJ 04RADIUS,CORNER,FIRST LEG FIRST LEG CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHQQJ 04WIDTH,END,FIRST LEG FIRST LEG END WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHQRJ 04DIAMETER,LEG,FIRST FIRST LEG DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHQSA /D/ 16STYLE,LEG,SECOND SECOND LEG STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SECOND LEG. 1A MODE REPLY 0 AHQTA /D/ 16STYLE,ARRANGEMENT,FIRST LEG HOLE FIRST LEG HOLE ARRANGEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE FIRST LEG HOLES. 1A MODE REPLY 0 AHQUJ 04DISTANCE BETWEEN HOLE CENTERS ALONG WIDTH,LEG,FIRST FIRST LEG DISTANCE BETWEEN HOLE CENTERS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHQVJ 04DISTANCE BETWEEN UPPER HOLE CENTERS ALONG WIDTH,LEG,FIRST FIRST LEG DISTANCE BETWEEN UPPER HOLE CENTERS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHQWJ 04DISTANCE BETWEEN LOWER HOLE CENTERS ALONG WIDTH,LEG,FIRST FIRST LEG DISTANCE BETWEEN LOWER HOLE CENTERS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHQXJ 04DISTANCE BETWEEN HOLE CENTERS ALONG LENGTH,LEG,FIRST FIRST LEG DISTANCE BETWEEN HOLE CENTERS ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHQYJ 04DISTANCE BETWEEN FIRST AND SECOND HOLE CENTERS ALONG WIDTH,LEG,FIRST FIRST LEG DISTANCE BETWEEN FIRST AND SECOND HOLE CENTERS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHQZJ 04DISTANCE BETWEEN SECOND AND THIRD HOLE CENTERS ALONG WIDTH,LEG,FIRST FIRST LEG DISTANCE BETWEEN SECOND AND THIRD HOLE CENTERS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHRAJ 04DISTANCE FROM EDGE TO HOLE CENTER ALONG WIDTH,LEG,FIRST FIRST LEG DISTANCE FROM EDGE TO HOLE CENTER ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHRBJ 04DISTANCE FROM EDGE TO HOLE CENTER ALONG LENGTH,LEG,FIRST FIRST LEG DISTANCE FROM EDGE TO HOLE CENTER ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHRCJ 04DISTANCE BETWEEN FIRST AND SECOND HOLE CENTERS ALONG LENGTH,LEG,FIRST FIRST LEG DISTANCE BETWEEN FIRST AND SECOND HOLE CENTERS ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHRDJ 04DISTANCE BETWEEN SECOND AND THIRD HOLE CENTERS ALONG LENGTH,LEG,FIRST FIRST LEG DISTANCE BETWEEN SECOND AND THIRD HOLE CENTERS ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHREJ 04DISTANCE BETWEEN THIRD AND FOURTH HOLE CENTERS ALONG WIDTH,FIRST LEG FIRST LEG DISTANCE BETWEEN THIRD AND FOURTH HOLE CENTERS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHRFJ 04RADIUS,CENTER,FIRST LEG HOLE FIRST LEG HOLE CENTER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHRGB /D/ 04ANGLE BETWEEN EDGE AND FIRST HOLE CENTER IN DEG,LEG,FIRST FIRST LEG ANGLE BETWEEN EDGE AND FIRST HOLE CENTER IN DEG NONE. 1B MODE REPLY 0 AHRHB /D/ 04ANGLE BETWEEN EDGE AND SECOND HOLE CENTER IN DEG,LEG,FIRST FIRST LEG ANGLE BETWEEN EDGE AND SECOND HOLE CENTER IN DEG NONE. 1B MODE REPLY 0 AHRJA /D/ 16STYLE,ARRANGEMENT,SECOND LEG HOLE SECOND LEG HOLE ARRANGEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE SECOND LEG HOLES. 1A MODE REPLY 0 AHRKD /D/ 08LOCATION,REINFORCEMENT REINFORCEMENT LOCATION INDICATES THE LOCATION OF THE REINFORCEMENT ON THE ITEM. SELECT REPLY CODE 10AE46 AHRLD 05DIRECTION,OPERATIONAL OPERATIONAL DIRECTION THE DIRECTION IN WHICH THE ITEM MOVES FOR OPERATION. SELECT REPLY CODE 10AA38 AHRMA 12QUANTITY,OFFSET OFFSET QUANTITY THE NUMBER OF ABRUPT BENDS IN THE ITEM. 1A MODE REPLY 0 AHRND /D/ 07SLIDE,NOTCHED NOTCHED SLIDE AN INDICATION OF WHETHER OR NOT A NOTCHED SLIDE IS INCLUDED. SELECT REPLY CODE 10AA49 AHRPD /D/ 07LUG,RETAINING RETAINING LUG AN INDICATION OF WHETHER OR NOT RETAINING LUGS ARE INCLUDED. SELECT REPLY CODE 10AA49 AHRQJ /D/ 04WIDTH,RIDGE RIDGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHRRJ 04HEIGHT,RIDGE RIDGE HEIGHT A MEASUREMENT FROM THE BASE TO THE RIDGE,IN DISTICTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AHRSJ /D/ 04DISTANCE BETWEEN RIDGE AND OPPOSITE WALL DISTANCE BETWEEN RIDGE AND OPPOSITE WALL NONE. 2D AND 1B MODE REPLY21AA051AC20 AHRTJ /D/ 04DISTANCE BETWEEN RIDGES DISTANCE BETWEEN RIDGES NONE. 2D AND 1B MODE REPLY21AA051AC20 AHRUJ 10WEIGHT,HEAD HEAD WEIGHT A RELATIVE MEASURE OF THE MASS OF A HEAD WITH RESPECT TO ITS DENSITY. 1D AND 1B MODE REPLY12AG69 AHRVL 16STYLE,CONSTRUCTION,TUBING WALL TUBING WALL CONSTRUCTION STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE CONSTRUCTION OF THE TUBING WALL. 1L MODE REPLY 0 AHRWD 18TYPE,TWIST,TUBING TUBING TWIST TYPE INDICATES THE TYPE OF TWIST AS CHARACTERIZED BY THE METHOD OR MANNER BY WHICH THE ROTATION OF THE CROSS-SECTIONAL AXES OF THE TUBING IS AFFECTED. SELECT REPLY CODE 10AF40 AHRXB 04ANGLE IN DEG,TWIST,TUBING TUBING TWIST ANGLE IN DEG THE ANGLE TO WHICH A RIGID TUBING HAS BEEN INTENTIONALLY ROTATED DURING MANUFACTURE OR THE MAXIMUM ANGLE TO WHICH A TWISTABLE TYPE TUBING MAY BE ROTATED,AS MEASURED IN DEGREES OF ANGULAR DIFFERENCE BETWEEN THE PLANE OF A SPECIFIC TRANSVERSE DIMENSION AT ONE EXTREMITY OF THE TUBING AND THE PLANE OF THE SAME DIMENSION AT THE OTHER EXTREMITY. 1B MODE REPLY 0 AHRYD /D/ 19TUBING,PLANE,BEND BEND PLANE TUBING THE KIND OF BEND,ELBOW,OR CORNER DENOTED BY AN ALPHABETIC CHARACTER,WHICH DISTINGUISHES THE PLANE IN WHICH A RIGID RECTANGULAR TUBINGS LONGITUDINAL AXIS DEVIATES /BY DESIGN/ FROM A STRAIGHT LINE. SELECT REPLY CODE 10AF41 AHRZD 09MATERIAL,FACE FACE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FACE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10MA01 AHSAD /D/ 09MATERIAL,TUBING TUBING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TUBING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AHSBD /D/ 17SURFACE TREATMENT,INSIDE,TUBING TUBING INSIDE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE INSIDE SURFACE OF THE TUBING. SELECT REPLY CODE 10AD09 AHSCD /D/ 17SURFACE TREATMENT,OUTSIDE,TUBING TUBING OUTSIDE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE OUTSIDE SURFACE OF THE TUBING. SELECT REPLY CODE 10AD09 AHSDJ /D/ 04HEIGHT,BEARING BEARING HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AHSEA /D/ 19NUMBER,PART,TUBING MANUFACTURER TUBING MANUFACTURER PART NUMBER THE IDENTIFYING PART NUMBER ASSIGNED TO THE TUBING BY THE MANUFACTURER. 1A MODE REPLY 0 AHSFA 12QUANTITY,FLANGE FLANGE QUANTITY THE NUMBER OF FLANGES PROVIDED WITH THE ITEM. 1A MODE REPLY 0 AHSGD /D/ 07SIMILARITY,FLANGE FLANGE SIMILARITY AN INDICATION OF WHETHER OR NOT THE FLANGES ARE IDENTICAL IN ALL SIGNIFICANT CHARACTERISTICS,SUCH AS TYPE,MATERIAL,DIMENSIONS,AND OTHER ELEMENTS. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. SELECT REPLY CODE 10AA37 AHSHJ /D/ 04DISTANCE,OFFSET,LONGER LONGER OFFSET DISTANCE NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 2D AND 1B MODE REPLY21AA051AC20 AHSJJ 04LENGTH,LEG LEG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE LEG,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AHSKJ /D/ 04LENGTH,LEG,LONGER LONGER LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHSLJ /D/ 04WIDTH,INSIDE,ACCOMMODATED WAVEGUIDE ACCOMMODATED WAVEGUIDE INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHSMJ /D/ 04HEIGHT,INSIDE,ACCOMMODATED WAVEGUIDE ACCOMMODATED WAVEGUIDE INSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AHSNJ /D/ 04WIDTH,OUTSIDE,ACCOMMODATED WAVEGUIDE ACCOMMODATED WAVEGUIDE OUTSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHSPJ /D/ 04HEIGHT,OUTSIDE,ACCOMMODATED WAVEGUIDE ACCOMMODATED WAVEGUIDE OUTSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AHSQJ /D/ 04DIAMETER,INSIDE,ACCOMMODATED WAVEGUIDE ACCOMMODATED WAVEGUIDE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHSRJ /D/ 04DIAMETER,OUTSIDE,ACCOMMODATED WAVEGUIDE ACCOMMODATED WAVEGUIDE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHSSJ 04WIDTH,OUTSIDE,COUPLING COUPLING OUTSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHSTJ 04HEIGHT,OUTSIDE,COUPLING COUPLING OUTSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AHSUJ 04DIAMETER,OUTSIDE,COUPLING COUPLING OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COUPLING,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AHSVJ /D/ 04DEPTH,INSERTION,WAVEGUIDE WAVEGUIDE INSERTION DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHSWJ /D/ 04THICKNESS,SURFACE,CONDUCTING,INTERIOR INTERIOR CONDUCTING SURFACE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHSXJ 04WIDTH,INSIDE,FLANGE FLANGE INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHSYJ 04HEIGHT,INSIDE,FLANGE FLANGE INSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AHSZJ 04WIDTH,OUTSIDE,FLANGE FLANGE OUTSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHTAJ 04HEIGHT,OUTSIDE,FLANGE FLANGE OUTSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AHTBJ 04DIAMETER,INSIDE,FLANGE FLANGE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHTCJ 04DIAMETER,OUTSIDE,FLANGE FLANGE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FLANGE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AHTDJ 04DEPTH,FLANGE FLANGE DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE FLANGE,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AHTEJ /D/ 04WIDTH,RIDGE,FLANGE FLANGE RIDGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHTFJ /D/ 04HEIGHT,RIDGE,FLANGE FLANGE RIDGE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AHTGJ /D/ 04DISTANCE,RIDGE TO RIDGE/WALL RIDGE TO RIDGE/WALL DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AHTHD /D/ 09MATERIAL,FLANGE FLANGE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FLANGE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH USE OF ISAC TBL 0094 IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AHTJD /D/ 17SURFACE TREATMENT,INSIDE,FLANGE FLANGE INSIDE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE INSIDE SURFACE OF THE FLANGE. SELECT REPLY CODE 10AD09 AHTKD /D/ 17SURFACE TREATMENT,OUTSIDE,FLANGE FLANGE OUTSIDE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE OUTSIDE SURFACE OF THE FLANGE. SELECT REPLY CODE 10AD09 AHTLD /D/ 11METHOD,CONNECTION,FLANGE FLANGE CONNECTION METHOD THE MECHANICAL MEANS OF ATTACHING THE FLANGE TO A MATING FLANGE OR TO THE EQUIPMENT SURFACE. SELECT REPLY CODE 10AB89 AHTMA 12QUANTITY,FACILITY,FLANGE CONNECTION FLANGE CONNECTION FACILITY QUANTITY THE NUMBER OF HOLES,STUDS,SCREWS,OR OTHER DEVICES INTEGRAL TO THE FLANGE PROVIDED FOR ATTACHING THE FLANGE TO A MATING SURFACE. 1A MODE REPLY 0 AHTNJ 04DIAMETER,HOLE,CONNECTING,FLANGE FLANGE CONNECTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FLANGE CONNECTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AHTPJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,FACILITY,FLANGE CONNECTING FLANGE CONNECTING FACILITY THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE OF THE FLANGE CONNECTING FACILITY/IES/. 1D AND 1A MODE REPLY12AC21 AHTQD /D/ 07PROVISION,ALIGNMENT,FLANGE MATING FLANGE MATING ALIGNMENT PROVISION AN INDICATION OF WHETHER OR NOT A PROVISION IS INCLUDED TO ALLOW THE FLANGE TO BE PLACED ONLY IN A PREDETERMINED POSITION. SELECT REPLY CODE 10AA49 AHTRA /D/ 19NUMBER,PART,FLANGE MANUFACTURER FLANGE MANUFACTURER PART NUMBER THE IDENTIFYING PART NUMBER ASSIGNED TO THE FLANGE BY THE MANUFACTURER. 1A MODE REPLY 0 AHTSA /D/ 19CODE,MANUFACTURER,COAXIAL CONNECTOR COAXIAL CONNECTOR MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE COAXIAL CONNECTOR. 1A MODE REPLY 0 AHTTA /D/ 19IDENTIFICATION,CONNECTOR,COAXIAL COAXIAL CONNECTOR IDENTIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS IDENTIFICATION NUMBER OR SYMBOL USED TO IDENTIFY THE COAXIAL CONNECTOR. 1A MODE REPLY 0 AHTUA /D/ 19NUMBER,PART,COAXIAL CONNECTOR COAXIAL CONNECTOR PART NUMBER THE IDENTIFYING PART NUMBER ASSIGNED TO THE COAXIAL CONNECTOR. 1A MODE REPLY 0 AHTVD /D/ 07FACILITY,PRESSURIZING PRESSURIZING FACILITY AN INDICATION OF WHETHER OR NOT A PHYSICAL FEATURE WHICH PROVIDES A MEANS FOR APPLYING OR RELIEVING A GASEOUS PRESSURE WITHIN THE ITEM IS INCLUDED. SELECT REPLY CODE 10AA49 AHTWB 10RATIO,WAVE,STANDING,VOLTAGE VOLTAGE STANDING WAVE RATIO THE RATIO OF THE MAXIMUM TO THE MINIMUM AMPLITUDE OF PRESSURE /VOLTAGE/ MEASURED ALONG THE PATH OF THE WAVES. 1B MODE REPLY 0 AHTXB 10LOSS IN DECIBELS,INSERTION INSERTION LOSS IN DECIBELS THE DIFFERENCE IN THE AMOUNT OF ENERGY AVAILABLE BEFORE AND AFTER THE INSERTION OF AN APPARATUS IN A TRANSMISSION SYSTEM,EXPRESSED IN DECIBELS. 1B MODE REPLY 0 AHTYB 10IMPEDANCE RATING IN OHMS,INPUT INPUT IMPEDANCE RATING IN OHMS THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) WHICH THE ITEM OFFERS TO THE ADMITTANCE OF AN ENTERING FLOW OF ALTERNATING CURRENT,EXPRESSED IN OHMS. 1B MODE REPLY 0 AHTZB 10IMPEDANCE RATING IN OHMS,OUTPUT OUTPUT IMPEDANCE RATING IN OHMS THE TOTAL OPPOSITION /RESISTIVE AND REACTIVE/ WHICH THE OUTPUT OF THE ITEM PROVIDES TO MATCH,FOR MAXIMUM TRANSFER OF ENERGY,THE INPUT IMPEDANCE OF ANOTHER ITEM,EXPRESSED IN OHMS. 1B MODE REPLY 0 AHUAB 10RATIO,BANDWIDTH BANDWIDTH RATIO A NUMERIC FACTOR,TO ONE DECIMAL PLACE,BY WHICH THE FREQUENCY BANDS LOWER LIMIT FREQUENCY VALUE IS MULTIPLIED TO OBTAIN THE APPROXIMATE UPPER FREQUENCY VALUE LIMIT OF THE BAND,COMPARED TO ONE /UNITY/ /NOT GIVEN/. 1B MODE REPLY 0 AHUBJ /D/ 04ANGLE IN DEG PER FOOT,BEND,MINIMUM MINIMUM BEND ANGLE IN DEG PER FOOT THE SMALLEST PERMISSIBLE ANGLE,INCLUDED WITHIN THE INTERSECTION OF LINES PARALLEL TO THE MATING FACES OF THE END FLANGES,WHEN A ONE FOOT SECTION OF A FLEXIBLE ASSEMBLY IS BENT IN A UNIFORM ARC IN THE SPECIFIED PLANE TO THE MAXIMUM EXTENT WITHOUT DAMAGE,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AF41 AHUCD 03DESIGNATION,SERIES,COAXIAL CONNECTOR COAXIAL CONNECTOR SERIES DESIGNATION A LETTER OR GROUP OF LETTERS USED TO DESIGNATE THE PARTICULAR COAXIAL CONNECTOR SERIES. SELECT REPLY CODE 10AF42 AHUDD 02DESIGN,END,CONNECTOR CONNECTOR END DESIGN THE DESIGN OF THE CONNECTOR END. SELECT REPLY CODE 10AB60 AHUEA 19NUMBER,MODEL,CARTRIDGE CARTRIDGE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE CARTRIDGE. 1A MODE REPLY 0 AHUFD 18TYPE,DESIGN,CARTRIDGE CARTRIDGE DESIGN TYPE INDICATES THE DESIGN TYPE CHARACTERISTIC OF THE CARTRIDGE. SELECT REPLY CODE 10AF43 AHUGD 18TYPE,GROUPING,CARTRIDGE CARTRIDGE GROUPING TYPE INDICATES THE PARTICULAR TYPE OF GROUPING IN WHICH THE CARTRIDGE IS SUPPLIED. SELECT REPLY CODE 10AF44 AHUHA 12QUANTITY,CARTRIDGE CARTRIDGE QUANTITY THE NUMBER OF CARTRIDGES OF WHICH THE GROUPING IS COMPOSED. 1A MODE REPLY 0 AHUJA 19NUMBER,MODEL,BELT BELT MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE BELT. 1A MODE REPLY 0 AHUKA 19NUMBER,MODEL,CLIP CLIP MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE CLIP. 1A MODE REPLY 0 AHULA 19NUMBER,MODEL,LINK LINK MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE LINK. 1A MODE REPLY 0 AHUMD 18TYPE,FUZE,NOSE NOSE FUZE TYPE INDICATES THE TYPE OF NOSE FUZE INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AF46 AHUNA 19NUMBER,MODEL,END LINK END LINK MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE END LINK. 1A MODE REPLY 0 AHUPA 19SEQUENCE,FUNCTIONAL,CARTRIDGE GROUPING CARTRIDGE GROUPING FUNCTIONAL SEQUENCE AN INDICATION OF THE SEQUENCING OF THE DIFFERENT TYPES OF CARTRIDGES WITHIN THE CARTRIDGE GROUPING. 1A MODE REPLY 0 AHUQJ 04DEPTH FOR WHICH DESIGNED,CHAMBER CHAMBER DEPTH FOR WHICH DESIGNED THE DEPTH OF THE CHAMBER FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 AHURD /D/ 09MATERIAL,CASE,CARTRIDGE CARTRIDGE CASE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CARTRIDGE CASE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AHUSD 18TYPE,FILLER,PROJECTILE PROJECTILE FILLER TYPE INDICATES THE TYPE OF FILLER WHICH IS CONTAINED WITHIN THE PROJECTILE. SELECT REPLY CODE 10AF45 AHUTD /D/ 09MATERIAL,JACKET,PROJECTILE PROJECTILE JACKET MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PROJECTILE COVERING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AHUUJ 10WEIGHT,PROJECTILE PROJECTILE WEIGHT THE WEIGHT OF THE PROJECTILE. 1D AND 1B MODE REPLY12AB16 AHUVD 01COLOR,BURST,PROJECTILE PROJECTILE BURST COLOR THE COLOR OF THE SMOKE CLOUD PRODUCED BY THE PROJECTILE WHEN EXPLODED. SELECT REPLY CODE 10AD06 AHUWA 19NUMBER,MODEL,PROJECTILE PROJECTILE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE PROJECTILE. 1A MODE REPLY 0 AHUXD /D/ 07ELEMENT,TRACER TRACER ELEMENT AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES A TRACER ELEMENT. SELECT REPLY CODE 10AA49 AHUYA 19NUMBER,MODEL,TRACER ELEMENT TRACER ELEMENT MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE TRACER ELEMENT. 1A MODE REPLY 0 AHUZD 18TYPE,FUZE FUZE TYPE INDICATES THE TYPE OF FUZE INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AF46 AHVAJ 10TIME,DELAY,FUZE FUZE DELAY TIME THE PERIOD OF ELAPSED TIME BETWEEN INITIATION OF THE FUZE AND DETONATION OF THE CHARGE. 2D AND 1B MODE REPLY22AH681AC20 AHVBA 19NUMBER,MODEL,FUZE FUZE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE FUZE. 1A MODE REPLY 0 AHVCD /D/ 07FUZE FUZE AN INDICATION OF WHETHER OR NOT A FUZE IS INCLUDED. SELECT REPLY CODE 10AA49 AHVDA 19NUMBER,MODEL,AUXILIARY DETONATING FUZE AUXILIARY DETONATING FUZE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE AUXILIARY DETONATING FUZE. 1A MODE REPLY 0 AHVED /D/ 07BOOSTER INCLUDED BOOSTER INCLUDED AN INDICATION OF WHETHER OR NOT THE ITEM CONTAINS A BOOSTER. SELECT REPLY CODE 10AA89 AHVFA 19NUMBER,MODEL,BOOSTER BOOSTER MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE BOOSTER. 1A MODE REPLY 0 AHVGA 19NUMBER,MODEL,PRIMER PRIMER MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE PRIMER. 1A MODE REPLY 0 AHVHA 19NUMBER,MODEL,IGNITION CARTRIDGE IGNITION CARTRIDGE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE IGNITION CARTRIDGE. 1A MODE REPLY 0 AHVJD /D/ 07CHARGE,SUPPLEMENTARY SUPPLEMENTARY CHARGE AN INDICATION OF WHETHER OR NOT A SUPPLEMENTARY CHARGE IS INCLUDED. PLEASE USE MRC ABFF. SELECT REPLY CODE 10AA49 AHVKJ 10WEIGHT,CHARGE,PROPELLING PROPELLING CHARGE WEIGHT THE WEIGHT OF THE PROPELLING CHARGE. 1D AND 1B MODE REPLY12AB16 AHVLA 19NUMBER,MODEL,PROPELLING CHARGE PROPELLING CHARGE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE PROPELLING CHARGE. 1A MODE REPLY 0 AHVMJ 04SIZE,CARTRIDGE CARTRIDGE SIZE THE DESIGNATED SIZE OF THE CARTRIDGE. 1D AND 1B MODE REPLY11AF47 AHVND 11METHOD,INITIATION,DETONATION DETONATION INITIATION METHOD THE MEANS USED TO INITIATE DETONATION OF THE ITEM. SELECT REPLY CODE 10AF48 AHVPA 12QUANTITY,INCREMENT,PROPELLING CHARGE PROPELLING CHARGE INCREMENT QUANTITY THE NUMBER OF INCREMENTS WHICH COMPOSE THE PROPELLING CHARGE. 1A MODE REPLY 0 AHVQD 19WEAPON FOR WHICH DESIGNED WEAPON FOR WHICH DESIGNED AN INDICATION OF THE WEAPON/S/ FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AF49 AHVRD 03DESIGNATOR,GRADE,CARTRIDGE CARTRIDGE GRADE DESIGNATOR A DESIGNATION INDICATING THE RATED GRADE OF THE CARTRIDGE. SELECT REPLY CODE 10AF50 AHVSD 03DESIGNATOR,SIZE,SHOT LOAD SHOT LOAD SIZE DESIGNATOR A DESIGNATION INDICATING THE RATED SIZE OF THE BUCKSHOT OR SHOT CONTAINED IN THE ITEM. SELECT REPLY CODE 10AF51 AHVTJ 10WEIGHT,SHOT SHOT WEIGHT THE WEIGHT OF THE SHOT. 2D AND 1B MODE REPLY22AB161AC20 AHVUA 12QUANTITY,PELLET,BUCKSHOT BUCKSHOT PELLET QUANTITY THE NUMBER OF PELLETS WHICH COMPOSE THE BUCKSHOT LOAD. 1A MODE REPLY 0 AHVVD 18TYPE,FEATURE,NOSE NOSE FEATURE TYPE INDICATES THE PARTICULAR TYPE OF NOSE FEATURE CONTAINED IN THE ITEM. SELECT REPLY CODE 10AF52 AHVWD /D/ 18TYPE,CHARGE,PYROTECHNIC PYROTECHNIC CHARGE TYPE INDICATES THE PARTICULAR TYPE OF PYROTECHNIC CHARGE UTILIZED IN THE ITEM. SELECT REPLY CODE 10AF53 AHVXD 19STAGE,APPLICATION,SURFACE TREATMENT SURFACE TREATMENT APPLICATION STAGE AN INDICATION OF THE PARTICULAR STAGE OF THE FABRICATION PROCESS AT WHICH THE SURFACE TREATMENT IS APPLIED. SELECT REPLY CODE 10AF54 AHVYA /D/ 16STYLE,SHAPE,MESH MESH SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE MESH. 1A MODE REPLY 0 AHVZA 19SIZE,MESH MESH SIZE THE ALPHA AND/OR NUMERIC SIZE DESIGNATION BY WHICH THE MESH IS IDENTIFIED. 1A MODE REPLY 0 AHWAJ 04HEIGHT,WIRE,CLEAR OPENING CLEAR OPENING WIRE HEIGHT THE MEASURED DISTANCE BETWEEN ADJACENT HORIZONTAL WIRES. 2D AND 1B MODE REPLY21AA051AC20 AHWBA 12QUANTITY,SPACING,HORIZONTAL HORIZONTAL SPACING QUANTITY THE NUMBER OF HORIZONTAL SPACINGS AS RELATED TO EACH DIMENSION FROM BOTTOM TO TOP. 1A MODE REPLY 0 AHWCJ 04WIDTH,WIRE,CLEAR OPENING CLEAR OPENING WIRE WIDTH THE MEASURED DISTANCE BETWEEN ADJACENT PICKET /VERTICAL/ WIRES. 2D AND 1B MODE REPLY21AA051AC20 AHWDD 18TYPE,WEAVE WEAVE TYPE INDICATES THE TYPE OF WEAVE THAT CORRESPONDS TO THE PATTERN IN WHICH THE WARP AND FILL OF THE ITEM ARE INTERWOVEN. SELECT REPLY CODE 10AG70 AHWED 18TYPE,CRIMP,WIRE WIRE CRIMP TYPE INDICATES THE TYPE OF CRIMP USED TO INTERLOCK THE WOVEN WIRES IN A FIXED POSITION. SELECT REPLY CODE 10AG89 AHWFD /D/ 19PROCESS AFTER FABRICATION PROCESS AFTER FABRICATION A PROCESS APPLIED TO THE FINISHED ITEM,BY PRESSING BETWEEN ROLLERS TO PRODUCE A SMOOTH FINISH AND UNIFORM THICKNESS. SELECT REPLY CODE 10AA62 AHWGJ A12QUANTITY,MESH,LONGITUDINAL DIRECTION LONGITUDINAL DIRECTION MESH QUANTITY THE NUMBER OF MESHES,OR INTERVENING OPENINGS,INCLUDED IN THE MEASUREMENT FROM THE CENTER OF A FILAMENT TO A SPECIFIED DISTANCE. 1D AND 1A MODE REPLY11AB39 AHWHJ A12QUANTITY,MESH,TRANSVERSE DIRECTION TRANSVERSE DIRECTION MESH QUANTITY THE NUMBER OF MESHES,OR INTERVENING OPENINGS,INCLUDED IN THE MEASUREMENT FROM THE CENTER OF A FILAMENT TO A SPECIFIED DISTANCE. 1D AND 1A MODE REPLY11AB39 AHWJJ 04WIDTH,MESH MESH WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A RECTANGULAR MESH SPACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AHWKJ 04LENGTH,MESH MESH LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A RECTANGULAR MESH SPACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AHWLD 05DIRECTION,LENGTH TO WARP,MESH MESH LENGTH TO WARP DIRECTION THE RELATIONSHIP OF THE MESH LENGTH TO THE WARP. SELECT REPLY CODE 10AF57 AHWMJ 04SIZE,FILAMENT FILAMENT SIZE DESIGNATES THE LINEAR SIZE OF THE INDIVIDUAL FILAMENT(S). 2D AND 1B MODE REPLY21AA051AC20 AHWND 18TYPE,FEATURE,PROPELLING CHARGE PROPELLING CHARGE FEATURE TYPE INDICATES THE PARTICULAR TYPE OF PROPELLING CHARGE FEATURE INCORPORATED IN THE ITEM. SELECT REPLY CODE 10AF55 AHWPD /D/ 08LOCATION,FILAMENT FILAMENT LOCATION INDICATES THE LOCATION OF THE FILAMENT(S) IN RELATION TO THE ITEM. SELECT REPLY CODE 10AE46 AHWQJ 04WIDTH,OPENING,ELBOW ELBOW OPENING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHWRJ 04LENGTH,OPENING,ELBOW ELBOW OPENING LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHWSJ 10CONSUMPTION RATING,ENERGY ENERGY CONSUMPTION RATING THE ENERGY CONSUMPTION OF THE ITEM AS DETERMINED BY A GOVERNMENT OR INDUSTRY STANDARD. 1D AND 1B MODE REPLY12AD68 AHWUJ /D/ 04WIDTH,TOE,TOP TOP TOE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHWVD 10CAPACITY,DISK DISK CAPACITY THE STORAGE CAPACITY OF THE DISK. SELECT REPLY CODE 10AG67 AHWWJ 04WIDTH,YOKE YOKE WIDTH NONE 2D AND 1B MODE REPLY21AA051AC20 AHWXJ /D/ 04LENGTH,SLOT,BODY BODY SLOT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHWYJ 04HEIGHT,INSULATOR INSULATOR HEIGHT NONE 2D AND 1B MODE REPLY21AA051AC20 AHWZJ /D/ 04DEPTH,GROOVE,BODY BODY GROOVE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHXAJ 04DISTANCE BETWEEN SPOOLS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SPOOLS NONE 2D AND 1B MODE REPLY21AA051AC20 AHXBJ /D/ 04DISTANCE FROM CENTER OF FIRST HOLE TO CENTER OF SECOND HOLE DISTANCE FROM CENTER OF FIRST HOLE TO CENTER OF SECOND HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 AHXCA /D/ 10RATE IN SECONDS,IMAGE DISSOLVE IMAGE DISSOLVE RATE IN SECONDS THE TIME REQUIRED FOR ONE PROJECTED OR DISPLAYED IMAGE TO FADE (DISSOLVE) AND ANOTHER IMAGE TO APPEAR, EXPRESSED IN SECONDS. 1A MODE REPLY 0 AHXDA /D/ 10RATE IN SECONDS,IMAGE FREEZE IMAGE FREEZE RATE IN SECONDS THE TIME A PROJECTED OR DISPLAYED IMAGE APPEARS BEFORE IT IS REPLACED WITH ANOTHER IMAGE, EXPRESSED IN SECONDS. 1A MODE REPLY 0 AHXEJ 04WIDTH,GROOVE,BODY BODY GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHXFA /D/ 12QUANTITY ACCOMMODATED,PROJECTOR PROJECTOR QUANTITY ACCOMMODATED THE NUMBER OF PROJECTORS THE ITEM CAN ACCOMMODATE. 1A MODE REPLY 0 AHXGJ /D/ 04LENGTH,OVERHANG,CLIP CLIP OVERHANG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHXHJ /D/ 04HEIGHT,INSIDE,CLIP OPENING CLIP OPENING INSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AHXJJ /D/ 04WIDTH,INSIDE,CLIP OPENING CLIP OPENING INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHXKJ 04DISTANCE,MEASURED,MAXIMUM MAXIMUM MEASURED DISTANCE THE MAXIMUM DISTANCE THAT CAN BE MEASURED BY THE ITEM WITH ACCURACY 1D AND 1B MODE REPLY11AA05 AHXLJ /D/ 10ANGLE,CUTTING,MAXIMUM MAXIMUM CUTTING ANGLE THE MAXIMUM CUTTING ANGLE OF THE ITEM. 1D AND 1B MODE REPLY11AA05 AHXMJ /D/ 04WIDTH,CABLE,SHUNT SHUNT CABLE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHXNJ /D/ 04THICKNESS,CABLE,SHUNT SHUNT CABLE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AHXPJ 04LENGTH,SHUNT,BRUSH BRUSH SHUNT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BRUSH SHUNT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AHXQJ 04DIAMETER,HOLE,TERMINAL TERMINAL HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHXRJ 04WIDTH,SLOT,TERMINAL TERMINAL SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHXSJ /D/ 04LENGTH,SLOT,TERMINAL TERMINAL SLOT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHXTJ /D/ 04DIAMETER,MAJOR,TERMINAL TERMINAL MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHXUJ /D/ 04DIAMETER,MINOR,TERMINAL TERMINAL MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHXVJ /D/ 10CAPACITY,DIELECTRIC FLUID DIELECTRIC FLUID CAPACITY THE RECOMMENDED AMOUNT OF DIELECTRIC FLUID IN TANK TO OPERATE THE ITEM. 1D AND 1B MODE REPLY12AG67 AHXWJ /D/ 04WIDTH,MAJOR,TERMINAL TERMINAL MAJOR WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHXXJ /D/ 04WIDTH,MINOR,TERMINAL TERMINAL MINOR WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHXYJ /D/ 10SIZE,FILTRATION,MINIMUM PARTICLE MINIMUM PARTICLE FILTRATION SIZE THE SIZE OF THE SMALLEST PARTICLE THAT WILL BE REMOVED BY A FILTER OR FILTERING SYSTEM. 1D AND 1B MODE REPLY12AG67 AHXZJ /D/ 10WEIGHT,FEEDING MECHANISM TOOL,MAXIMUM MAXIMUM FEEDING MECHANISM TOOL WEIGHT THE WEIGHT OF THE HEAVIEST TOOL THAT CAN BE EFFECTIVELY SUPPORTED BY THE FEEDING MECHANISM. 1D AND 1B MODE REPLY12AG67 AHYAJ 04HEIGHT,MAXIMUM,TABLE TO HORN TABLE TO HORN MAXIMUM HEIGHT THE MAXIMUM DISTANCE FROM THE HORN TO THE TABLE. 1D AND 1B MODE REPLY11AA05 AHYBD /D/ 18TYPE,ANVIL ANVIL TYPE THE TYPE OF ANVIL INCLUDED ON THE ITEM. SELECT REPLY CODE 10AK95 AHYCJ /D/ 04LENGTH,COMPRESSED,SPRING SPRING COMPRESSED LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHYDD /D/ 08LOCATION,EDGE EDGE LOCATION INDICATES THE LOCATION OF THE EDGE IN RELATION TO THE ITEM. SELECT REPLY CODE 10AE46 AHYEJ /D/ 04DISTANCE FROM EDGE OF BRUSH TO BODY OF SLOT DISTANCE FROM EDGE OF BRUSH TO BODY OF SLOT NONE. 2D AND 1B MODE REPLY21AA051AC20 AHYFA 12QUANTITY,HOLE,SECURING SECURING HOLE QUANTITY THE NUMBER OF HOLES PROVIDED FOR SECURING THE ITEM IN A FIXED POSITION. 1A MODE REPLY 0 AHYGB 04ANGLE BETWEEN CENTERLINES OF SECURING HOLES IN DEG ANGLE BETWEEN CENTERLINES OF SECURING HOLES IN DEG A MEASUREMENT OF THE AMOUNT OF TURNING NECESSARY TO BRING ONE HOLE INTO COINCIDENCE WITH ANOTHER,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AHYHA /D/ 16STYLE,HOLE,COLLAR SECURING COLLAR SECURING HOLE STYLE THE STYLE DESIGNATION INDICATING A CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE HOLE/S/ PROVIDED FOR SECURING THE ITEM. 1A MODE REPLY 0 AHYJL 16STYLE,HOLE,CLAMP SECURING CLAMP SECURING HOLE STYLE THE STYLE DESIGNATION INDICATING A CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE HOLE/S/ PROVIDED FOR SECURING THE CLAMP. 1L MODE REPLY 0 AHYKJ 04DISTANCE BETWEEN SHAFT HOLE AND BORE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SHAFT HOLE AND BORE NONE. 2D AND 1B MODE REPLY21AA051AC20 AHYLJ 04DEPTH,NOTCH NOTCH DEPTH AN INSIDE MEASUREMENT BETWEEN SPECIFIED POINTS OF A NOTCH,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AHYMJ 04THREAD DIAMETER,NOMINAL NOMINAL THREAD DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AHYNJ /D/ 10CAPACITY,ABRASIVE POWDER ABRASIVE POWDER CAPACITY THE STORAGE CAPACITY OF THE ABRASIVE POWDER FEEDER. 1D AND 1B MODE REPLY12AG67 AHYPB /D/ 04ANGLE IN DEG,HOLE,THREADED COUNTERSUNK THREADED COUNTERSUNK HOLE ANGLE IN DEG NONE. 1B MODE REPLY 0 AHYQJ 04WIDTH,SLOT,BODY BODY SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AHYRJ /D/ 04DIAMETER,MAJOR,THREADED HOLE COUNTERSINK THREADED HOLE COUNTERSINK MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHYSJ /D/ 04DIAMETER,MAJOR,UNTHREADED HOLE COUNTERSINK UNTHREADED HOLE COUNTERSINK MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHYTJ /D/ 04DIAMETER,MINOR,UNTHREADED HOLE COUNTERSINK UNTHREADED HOLE COUNTERSINK MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AHYUB /D/ 04ANGLE IN DEG,HOLE,UNTHREADED COUNTERSUNK UNTHREADED COUNTERSUNK HOLE ANGLE IN DEG NONE. 1B MODE REPLY 0 AHYVJ 10FLOW RATE,DISCHARGE,MAXIMUM MAXIMUM DISCHARGE FLOW RATE THE MAXIMUM RATED CAPACITY DELIVERED BY THE ITEM. 1D AND 1B MODE REPLY11AC64 AHYWJ 10PRESSURE,DISCHARGE DISCHARGE PRESSURE THE PRESSURE OF THE MEDIA DELIVERED BY THE ITEM AT MAXIMUM RATED DISCHARGE CAPACITY. 1D AND 1B MODE REPLY11AB18 AHYXJ 10HEAD,TOTAL TOTAL HEAD THE SUM OF THE TOTAL DISCHARGE HEAD AND THE TOTAL SUCTION LIFT. 1D AND 1B MODE REPLY11AA05 AHYYJ 10LIFT,SUCTION SUCTION LIFT THE VERTICAL DISTANCE FROM THE LEVEL OF SUPPLY TO THE CENTER OF THE PUMP. 1D AND 1B MODE REPLY11AA05 AHYZJ 10SPEED AT RATED CAPACITY,OPERATING OPERATING SPEED AT RATED CAPACITY THE SPEED OF THE ITEM REQUIRED TO PRODUCE ITS RATED CAPACITY. 1D AND 1B MODE REPLY11AA22 AHZAD /D/ 19POSITION,OPERATING,PUMPING ELEMENT PUMPING ELEMENT OPERATING POSITION THE POSITION IN WHICH THE PUMPING ELEMENT/S/ IS DESIGNED TO OPERATE. SELECT REPLY CODE 10AC60 AHZBJ /D/ 04WIDTH,OVERALL,ASSEMBLY ASSEMBLY OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ASSEMBLY,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AHZCJ 04LENGTH,OVERALL,ASSEMBLY ASSEMBLY OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ASSEMBLY. 2D AND 1B MODE REPLY21AA051AC20 AHZDD 05DIRECTION,ROTATION,PUMP PUMP ROTATION DIRECTION THE DIRECTION IN WHICH THE PUMP SHAFT TURNS DURING OPERATION. SELECT REPLY CODE 10AC84 AHZED 02DESIGN,PUMP,CENTRIFUGAL CENTRIFUGAL PUMP DESIGN THE DESIGN OF A CENTRIFUGAL PUMP AS DETERMINED BY THE DIRECTION OF MEDIA FLOW WITH RESPECT TO THE AXIS OF THE SHAFT. SELECT REPLY CODE 10AA80 AHZFA 12QUANTITY,IMPELLER,CENTRIFUGAL PUMP CENTRIFUGAL PUMP IMPELLER QUANTITY THE NUMBER OF IMPELLERS INCORPORATED IN THE CENTRIFUGAL PUMP. 1A MODE REPLY 0 AHZGD 18TYPE,SUCTION,CENTRIFUGAL PUMP IMPELLER CENTRIFUGAL PUMP IMPELLER SUCTION TYPE INDICATES THE TYPE OF SUCTION PRODUCED BY THE IMPELLER OF THE CENTRIFUGAL PUMP. SELECT REPLY CODE 10AF09 AHZHD /D/ 07FEATURE,SELF-PRIMING SELF-PRIMING FEATURE AN INDICATION OF WHETHER OR NOT A SELF-PRIMING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AHZJD 02DESIGN,RECIPROCATING,PUMP PUMP RECIPROCATING DESIGN THE RECIPROCATING DESIGN OF THE PUMP. SELECT REPLY CODE 10AA79 AHZKA /D/ 19NAME,ITEM,END END ITEM NAME THE APPROVED ITEM NAME OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART. 1A MODE REPLY 0 AHZLJ /D/A19DOCUMENT,DATA,TUBING TUBING DATA DOCUMENT THE SPECIFICATION,STANDARD,OR DRAWING WHICH SPECIFICALLY CONTROLS THE FABRICATION OF THE TUBING, INCLUDES THE FEDERAL SUPPLY CODE FOR MANUFACTURERS /FSCM/ OF THE ENTITY CONTROLLING THE INSTRUMENT. 1D AND 1A MODE REPLY11AC28 AHZMJ /D/A19DOCUMENT,DATA,FLANGE FLANGE DATA DOCUMENT THE SPECIFICATION,STANDARD,OR DRAWING WHICH SPECIFICALLY CONTROLS THE FABRICATION OF THE FLANGE. INCLUDES THE FEDERAL SUPPLY CODE FOR MANUFACTURER /FSCM/ OF THE ENTITY CONTROLLING THE INSTRUMENT. 1D AND 1A MODE REPLY11AC28 AHZND 18TYPE,STROKE,RECIPROCATING RECIPROCATING STROKE TYPE INDICATES THE TYPE OF RECIPROCATING MOVEMENT WITHIN THE ITEM. SELECT REPLY CODE 10AC01 AHZPD 18TYPE,CONTROL,VOLUME VOLUME CONTROL TYPE INDICATES THE TYPE OF DEVICE USED TO CONTROL THE OUTPUT OR CAPACITY OF AN ITEM. SELECT REPLY CODE 10AH83 AHZQD /D/ 08LOCATION,CONTROL CONTROL LOCATION INDICATES THE LOCATION OF THE CONTROL ON THE ITEM. SELECT REPLY CODE 10AE46 AHZRD 02DESIGN,PUMP,ROTARY ROTARY PUMP DESIGN THE DESIGN OF A ROTARY PUMP AS DETERMINED BY THE MECHANICAL PRINCIPLE USED TO ACHIEVE MOVEMENT OF THE FLUID. SELECT REPLY CODE 10AA81 AHZSD 02DESIGN,RELATIONSHIP,OPERATION OPERATION RELATIONSHIP DESIGN AN INDICATION OF HOW THE ITEMS ARE DESIGNED TO OPERATE IN RELATION TO EACH OTHER. SELECT REPLY CODE 10AF56 AHZTD /D/ 11METHOD,OPERATION OPERATION METHOD THE MEANS BY WHICH THE ITEM IS OPERATED. PLEASE USE MRC APHE IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA77 AHZUD /D/ 07VALVE,RELIEF,INTEGRAL INTEGRAL RELIEF VALVE AN INDICATION OF WHETHER OR NOT AN INTEGRAL SAFETY DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 AHZVD 07SUBMERSIBILITY SUBMERSIBILITY AN INDICATION OF WHETHER OR NOT AN ITEM IS CAPABLE OF OPERATION WHILE SUBMERGED. SELECT REPLY CODE 10AG86 AHZWD /D/ 07STRAINER,INTEGRAL INTEGRAL STRAINER AN INDICATION OF WHETHER OR NOT A STRAINER IS INCLUDED AS AN INTEGRAL PART OF THE ITEM. SELECT REPLY CODE 10AA49 AHZXB 10HORSEPOWER RATING,MOVER,PRIME PRIME MOVER HORSEPOWER RATING THE RATED HORSEPOWER OF THE PRIME MOVER. 1B MODE REPLY 0 AHZYD 01COLOR,HANDLE HANDLE COLOR THE HUE OR TINT OF THE HANDLE. SELECT REPLY CODE 10AD06 AHZZD /D/ 19PROTECTION,ENVIRONMENTAL,MOTOR MOTOR ENVIRONMENTAL PROTECTION THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT THE MOTOR IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY. SELECT REPLY CODE 10AA65 AJAAJ 10TEMP RATING,STEAM STEAM TEMP RATING THE TEMPERATURE OF THE STEAM REQUIRED TO OPERATE AN ITEM AT FULL CAPACITY. 1D AND 1B MODE REPLY11AB36 AJABD 18TYPE,SHAFT,DRIVE DRIVE SHAFT TYPE INDICATES THE TYPE OF DRIVE SHAFT BY THE PHYSICAL CONFIGURATION,CONDITION,AND THE LIKE OF THE SHAFT END. SELECT REPLY CODE 10AF58 AJACJ 04DIAMETER,END,DRIVE SHAFT DRIVE SHAFT END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DRIVE SHAFT END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJADJ 04LENGTH,SHAFT,DRIVE DRIVE SHAFT LENGTH A MEASUREMENT OF THE DISTANCE THE DRIVE SHAFT EXTENDS FROM THE HOUSING. 2D AND 1B MODE REPLY21AA051AC20 AJAEB /D/ 10WEIGHT IN TROY OUNCES,MATERIAL,PRECIOUS PRECIOUS MATERIAL WEIGHT IN TROY OUNCES THE WEIGHT OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,EXPRESSED IN TROY OUNCES. 1B MODE REPLY 0 AJAFJ 04LENGTH,UNIT,UNPACKAGED UNPACKAGED UNIT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING, IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AJAGJ 04WIDTH,UNIT,UNPACKAGED UNPACKAGED UNIT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AJAHJ 04HEIGHT,UNIT,UNPACKAGED UNPACKAGED UNIT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AJAJG /D/ 09MATERIAL,FURNISHED,GOVERNMENT GOVERNMENT FURNISHED MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE USED IN THE FABRICATION OF THE ITEM,WHICH IS GOVERNMENT FURNISHED. FULL TEXT WRITE-IN 0 AJAKD /D/ 19CLASSIFICATION,MOVER,PRIME PRIME MOVER CLASSIFICATION THE SERVICE TYPE /CLASSIFICATION/ OF THE PRIME MOVER UTILIZED. SELECT REPLY CODE 10AF59 AJALD /D/ 09MATERIAL,BASIC,PUMP PUMP BASIC MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF THE BASIC MATERIAL OF WHICH THE MAJOR PORTION OF THE PUMP IS FABRICATED. SELECT REPLY CODE 10AD09 AJAMD 19CHARACTERISTICS,SERVICE SERVICE CHARACTERISTICS THOSE PROTECTIVE OR RESISTIVE QUALITIES THAT ARE INDICATIVE OF THE INTENDED SERVICE OF THE ITEM. SELECT REPLY CODE 10AF60 AJANJ 04LENGTH,ARM,SHORT SHORT ARM LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJAPJ 04DEPTH,OPENING,END,WRENCHING WRENCHING END OPENING DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJAQJ 04LENGTH,LUG LUG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJARJ /D/ 04ANGLE BETWEEN PINS IN DEG ANGLE BETWEEN PINS IN DEG NONE. 1D AND 1B MODE REPLY11AC20 AJASJ 04ANGLE BETWEEN LUGS IN DEG ANGLE BETWEEN LUGS IN DEG THE ANGLE BETWEEN THE LUGS,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 AJATJ 04HEIGHT,OFFSET OFFSET HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AJAUJ 04THICKNESS,HEAD,LARGE END LARGE END HEAD THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJAVJ 04THICKNESS,HEAD,SMALL END SMALL END HEAD THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJAWJ 04RADIUS,CIRCLE,HOLE HOLE CIRCLE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJAXJ 04LENGTH,BLADE,LARGE END LARGE END BLADE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJAYJ /D/ 04ANGLE IN DEG,OFFSET,WRENCHING END WRENCHING END OFFSET ANGLE IN DEG NONE. 1D AND 1B MODE REPLY11AC20 AJAZJ 04THICKNESS,HOOK HOOK THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJBAJ 04LENGTH,SECTION,SERRATED SERRATED SECTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SERRATED SECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AJBBJ 04DIAMETER,PIN,LARGE END LARGE END PIN DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGE END OF A PIN,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJBCJ 04DIAMETER,PIN,SMALL END SMALL END PIN DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJBDJ 04DISTANCE BETWEEN PINS,CENTER TO CENTER,END,LARGE LARGE END CENTER TO CENTER DISTANCE BETWEEN PINS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJBEJ 04DISTANCE BETWEEN PINS,CENTER TO CENTER,END,SMALL SMALL END CENTER TO CENTER DISTANCE BETWEEN PINS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJBFJ 04DIAMETER,RANGE,CIRCLE CIRCLE RANGE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJBGJ 04THICKNESS,BLADE BLADE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A BLADE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AJBHJ 04RADIUS,CIRCLE,PIN PIN CIRCLE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJBJJ 04DEPTH,BLADE BLADE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJBKJ 04LENGTH,BLADE,SMALL END SMALL END BLADE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJBLJ 04DIAMETER,OPENING,SMALL END SMALL END OPENING DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJBMJ 04DISTANCE BETWEEN LUGS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN LUGS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJBNJ /D/ 04ANGLE BETWEEN HOLES IN DEG ANGLE BETWEEN HOLES IN DEG NONE. 1D AND 1B MODE REPLY11AC20 AJBPD 17SURFACE TREATMENT,BLADE BLADE SURFACE TREATMENT THE METALLIC, NONMETALLIC, AND/OR CHEMICAL PROPERTIES WITH WHICH THE BLADE IS PLATED, DIPPED, AND/OR COATED. THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF. SELECT REPLY CODE 10SF01 AJBQH /D/ 14SHAPE AND LOCATION,SURFACE,WRENCHING WRENCHING SURFACE SHAPE AND LOCATION THE PHYSICAL CONFIGURATION OF THE WRENCHING SURFACE AND ITS LOCATION ON THE ITEM. 2D MODE REPLY 23AD073AJ91 AJBRJ 10SIZE,SURFACE,WRENCHING WRENCHING SURFACE SIZE DESIGNATES THE SIZE OF THE WRENCHING SURFACE. 2D AND 1B MODE REPLY21AA051AC20 AJBSA 13THREAD TOLERANCE CLASS THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE. 1A MODE REPLY 0 AJBTJ /D/ 12QUANTITY PER WRENCHING SURFACE,POINT POINT QUANTITY PER WRENCHING SURFACE THE NUMBER OF POINTS ON THE WRENCHING SURFACE. 1D AND 1B MODE REPLY13AE46 AJBUA 12QUANTITY,FLUTE,WRENCHING SURFACE WRENCHING SURFACE FLUTE QUANTITY THE NUMBER OF /GRIPPING/ FLUTES ON THE WRENCHING SURFACE. 1A MODE REPLY 0 AJBVD /D/ 07WRENCHING FEATURE,REPLACEABLE REPLACEABLE WRENCHING FEATURE AN INDICATION OF WHETHER OR NOT A REPLACEABLE WRENCHING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AJBWD /D/ 18TYPE,GRIPPING,PIPE PIPE GRIPPING TYPE INDICATES THE TYPE OF FEATURE(S) BUILT INTO THE ITEM FOR GRIPPING PIPE AND SIMILAR ITEMS. SELECT REPLY CODE 10AF61 AJBXD /D/ 18TYPE,MATERIAL,STRAP,PIPE GRIPPING PIPE GRIPPING STRAP MATERIAL TYPE INDICATES THE TYPE OF MATERIAL FROM WHICH THE PIPE GRIPPING STRAP IS FABRICATED. SELECT REPLY CODE 10AD93 AJBYJ /D/ 04SIZE AND LOCATION,SURFACE,DRIVE DRIVE SURFACE SIZE AND LOCATION DESIGNATES THE SIZE OF THE DRIVE SURFACE AND ITS LOCATION ON THE ITEM. 3D AND 1B MODE REPLY31AA051AC203AJ91 AJBZH /D/ 14SHAPE AND LOCATION,DRIVE SURFACE DRIVE SURFACE SHAPE AND LOCATION THE PHYSICAL CONFIGURATION OF THE DRIVE SURFACE AND ITS LOCATION ON THE ITEM. 3D MODE REPLY 33AD073AJ912AH46 AJCAL /D/ 16STYLE DESIGNATOR,DRYING CHAMBER DRYING CHAMBER STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE DRYING CHAMBER. 1L MODE REPLY 0 AJCBD /D/ 19FEATURE,PROTECTION,HAZARD HAZARD PROTECTION FEATURE THE FEATURE INHERENT IN OR DESIGNED INTO THE ITEM AS PROTECTION AGAINST RISKS ENCOUNTERED DURING USAGE. SELECT REPLY CODE 10AA65 AJCCD 19MECHANISM,RATCHET RATCHET MECHANISM AN INDICATION OF THE TYPE OF RATCHET MECHANSIM INCLUDED IN AN ITEM. SELECT REPLY CODE 10AF62 AJCDD /D/ 07HANDLE,REMOVABLE REMOVABLE HANDLE AN INDICATION OF WHETHER OR NOT A REMOVABLE HANDLE IS INCLUDED. SELECT REPLY CODE 10AA49 AJCEJ T04SIZE RANGE ACCOMMODATED,TAP TAP SIZE RANGE ACCOMMODATED AN INDICATION OF THE TAP HOLDING CAPACITY OF THE ITEM. 1D AND 1F MODE REPLY11AA05 AJCFD 19MECHANISM,INDICATING,TORQUE TORQUE INDICATING MECHANISM THE MEANS PROVIDED FOR SETTING THE APPLIED TORQUE. SELECT REPLY CODE 10AH83 AJCGJ 10CAPACITY,TORQUE TORQUE CAPACITY AN INDICATION OF THE UNIT OF MEASURE AND THE NUMERIC TORQUE LIMIT FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA561AC20 AJCHJ 10GRADUATION,SCALE,TORQUE TORQUE SCALE GRADUATION THE TORQUE SCALE DIVISIONS ON VISUAL INDICATING ITEMS. 1D AND 1B MODE REPLY11AA56 AJCJJ /D/ 04ANGLE IN DEG,HEAD,LARGE END LARGE END HEAD ANGLE IN DEG NONE. 1D AND 1B MODE REPLY11AC20 AJCKJ /D/ 04ANGLE IN DEG,HEAD,SMALL END SMALL END HEAD ANGLE IN DEG NONE. 1D AND 1B MODE REPLY11AC20 AJCLD /D/ 07DESIGN FEATURE,POWER TOOL POWER TOOL DESIGN FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES A DESIGN FEATURE TO FACILITATE THE USE OF POWER TOOLS. SELECT REPLY CODE 10AA49 AJCMD /D/ 07CUTTING FEATURE,WIRE WIRE CUTTING FEATURE AN INDICATION OF WHETHER OR NOT A MEANS FOR CUTTING WIRE IS INCLUDED. SELECT REPLY CODE 10AA49 AJCND 19FEATURE,STORAGE,PROTECTIVE PROTECTIVE STORAGE FEATURE THE PECULIAR STORAGE FEATURE/S/ REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS. SELECT REPLY CODE 10AA65 AJCPJ /D/ 04ANGLE IN DEG,OFFSET,DRIVE END DRIVE END OFFSET ANGLE IN DEG NONE. 1D AND 1B MODE REPLY11AC20 AJCQJ 04ANGLE IN DEG,HEAD HEAD ANGLE IN DEG THE ANGLE OF THE HEAD,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 AJCRA /D/ 12QUANTITY,ANTENNA ANTENNA QUANTITY THE NUMBER OF SEPARATELY EXCITED ANTENNAS COMPRISING AN ASSEMBLY OR SET. 1A MODE REPLY 0 AJCSJ 10FREQUENCY,RESONANT RESONANT FREQUENCY THE FREQUENCY AT WHICH AN ITEM WILL RESPOND WITH MAXIMUM AMPLITUDE. 1D AND 1B MODE REPLY11AC32 AJCTD 18TYPE,POLARIZATION,ELECTROMAGNETIC ELECTROMAGNETIC POLARIZATION TYPE THE ORIENTATION OF THE ELECTRICAL VECTOR OF ENERGY RADIATED FROM THE ITEM RELATIVE TO THE LINE OF PROPAGATION. SELECT REPLY CODE 10AF63 AJCUD 19PATTERN,RADIATION RADIATION PATTERN THE GRAPHICAL REPRESENTATION OF THE RADIATION PATTERN OF THE DEVICE AS A FUNCTION OF DIRECTION. SELECT REPLY CODE 10AE78 AJCVD 18TYPE,BEAM,UNIDIRECTIONAL UNIDIRECTIONAL BEAM TYPE INDICATES THE TYPE OF BEAM PATTERN OF RECEIVED SIGNALS FROM AN ITEM WITH UNIDIRECTIONAL RADIATION. SELECT REPLY CODE 10AF64 AJCWB /D/ 04ANGLE IN DEG,WIDTH,VERTICAL BEAM VERTICAL BEAM WIDTH ANGLE IN DEG THE ANGLE BETWEEN TWO OPPOSITE HALF-POWER /3 DECIBELS/ POINTS OF THE VERTICAL BEAM,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AJCXB /D/ 04ANGLE IN DEG,WIDTH,HORIZONTAL BEAM HORIZONTAL BEAM WIDTH ANGLE IN DEG THE ANGLE BETWEEN TWO OPPOSITE HALF-POWER /3 DECIBELS/ POINTS OF THE HORIZONTAL BEAM,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AJCYJ /D/ 04DIAMETER,ELEMENT ELEMENT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJCZJ 04HEIGHT,BASE BASE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A BASE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AJDAJ 04LENGTH,ELEMENT ELEMENT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ELEMENT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AJDBJ 10POWER RATING POWER RATING THE AMOUNT OF ELECTRICAL ENERGY THAT CAN BE DISSIPATED. 2D AND 1B MODE REPLY21AC331AF65 AJDCB /D/ 10GAIN IN DECIBELS,POWER,ANTENNA ANTENNA POWER GAIN IN DECIBELS AN EXPRESSION OF THE RATIO OF THE RADIATION INTENSITY OF AN ANTENNA IN A SPECIFIED DIRECTION TO THE POWER RADIATED IN THE SAME DIRECTION BY A STANDARD ANTENNA,EXPRESSED IN DECIBELS. 1B MODE REPLY 0 AJDDB 10IMPEDANCE IN OHMS,CHARACTERISTIC CHARACTERISTIC IMPEDANCE IN OHMS THE REACTANCE-RESISTANCE COMPLEX VALUE WHICH MUST BE MATCHED BY THE TRANSMISSION LINE AND TERMINATION TO ACHIEVE LOWEST STANDING WAVE RATIO,EXPRESSED IN OHMS. 1B MODE REPLY 0 AJDED /D/ 18TYPE,TERMINATION,ANTENNA ANTENNA TERMINATION TYPE INDICATES THE TYPE OF FACILITY PROVIDED ON THE DEVICE FOR ATTACHING CABLES,WAVEGUIDES,OR THE LIKE THAT CARRY THE RADIO FREQUENCY SIGNAL. SELECT REPLY CODE 10AF66 AJDFA 19IDENTIFICATION,TERMINATION TERMINATION IDENTIFICATION THE SPECIFICATION,STANDARD,OR THE NUMBER OR SYMBOL OF THE MANUFACTURER USED TO IDENTIFY THE TERMINATION. 1A MODE REPLY 0 AJDGA 19CODE,MANUFACTURER,TERMINATION TERMINATION MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE TERMINATION. 1A MODE REPLY 0 AJDHD 11METHOD,SCANNING,BEAM BEAM SCANNING METHOD THE MEANS USED TO DIRECT A BEAM/S/ OF ENERGY SUCCESSIVELY OVER A GIVEN REGION. SELECT REPLY CODE 10AD55 AJDJD 18TYPE,DEVICE,POSITIONING POSITIONING DEVICE TYPE INDICATES THE TYPE OF DEVICE USED TO EFFECT POSITIONING OR TO VARY POSITIONS (AS IN SCANNING) OF THE ITEM. SELECT REPLY CODE 10AE34 AJDKB 10ATTENUATION IN DECIBELS,SIGNAL,RF RF SIGNAL ATTENUATION IN DECIBELS THE DECREASE IN THE STRENGTH OF THE RADIO FREQUENCY SIGNALS,EXPRESSED IN DECIBELS. 1B MODE REPLY 0 AJDLB /D/ 10RATIO IN DECIBELS,SIGNAL,FRONT TO BACK FRONT TO BACK SIGNAL RATIO IN DECIBELS THE DIFFERENCE BETWEEN THE INPUT /FRONT/ AND REFLECTED /BACK/ SIGNAL RATIO,EXPRESSED IN DECIBELS. 1B MODE REPLY 0 AJDMB /D/ 10EFFICIENCY IN PERCENT,POWER POWER EFFICIENCY IN PERCENT THE RATIO OF POWER INPUT TO POWER OUTPUT,EXPRESSED IN PERCENT. 1B MODE REPLY 0 AJDNB /D/ 10PHASING IN WAVELENGTHS,ELEMENT ELEMENT PHASING IN WAVELENGTHS THE ELECTRICAL SPACING OF THE ELEMENTS,EXPRESSED IN WAVELENGTHS. 1B MODE REPLY 0 AJDPD /D/ 07PROVISION,ANTI-ICING ANTI-ICING PROVISION AN INDICATION OF WHETHER OR NOT AN ANTI-ICING PROVISION IS INCLUDED. SELECT REPLY CODE 10AA49 AJDQL /D/ 16STYLE DESIGNATOR,DESICCANT DESICCANT STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE DESICCANT. 1L MODE REPLY 0 AJDRD /D/ 11METHOD,SIGNAL,TORQUE TORQUE SIGNAL METHOD THE MEANS /AUDIBLE,VISUAL,AND THE LIKE/ USED TO SIGNIFY THAT THE TORQUE IS FUNCTIONING. SELECT REPLY CODE 10AD51 AJDSJ 04RADIUS,CIRCLE,LUG LUG CIRCLE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJDTJ 10CAPACITY PER HOUR,CHILLING CHILLING CAPACITY PER HOUR THE TOTAL MASS OF A MATERIAL THAT THE ITEM CAN CHILL TO A TARGET TEMPERATURE OF MINUS 120 DEGREES FAHRENHEIT (MINUS 84 DEGREES CELSIUS) IN ONE HOUR. 1D AND 1B MODE REPLY12AN75 AJDUA /D/ 12NUMBER OF ENGINES DISPLAYED,MAXIMUM MAXIMUM NUMBER OF ENGINES DISPLAYED THE MAXIMUM NUMBER OF ENGINES THAT CAN TRANSMIT DATA TO THE INDICATOR. 1A MODE REPLY 0 AJDVJ 04DIAMETER,OPENING,LARGE END LARGE END OPENING DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJDWJ 04DISTANCE BETWEEN PINS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN PINS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJDXJ 04RADIUS,END,FLANGE FLANGE END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJDYJ 04DIAMETER,CIRCLE,BOLT,OUTER OUTER BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJDZJ 04DIAMETER,CIRCLE,BOLT,INNER INNER BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJEAJ 04DIAMETER,HOLE,OUTER BOLT CIRCLE OUTER BOLT CIRCLE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJEBJ 04DIAMETER,HOLE,INNER BOLT CIRCLE INNER BOLT CIRCLE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJECJ 04HEIGHT,BOSS BOSS HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AJEDJ 04HEIGHT,FACE,RAISED RAISED FACE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP SURFACE OF A RAISED FACE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AJEEJ 04DIAMETER,FACE,RAISED RAISED FACE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A RAISED FACE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJEFJ 04DEPTH,BEVEL BEVEL DEPTH AN INSIDE MEASUREMENT BETWEEN SPECIFIED POINTS ON THE BEVEL,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AJEGJ 04HEIGHT,NECK NECK HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AJEHB /D/ 04ANGLE IN DEG,BEVEL,FACE FACE BEVEL ANGLE IN DEG NONE. 1B MODE REPLY 0 AJEJB /D/ 04ANGLE IN DEG,BEVEL,BOSS BOSS BEVEL ANGLE IN DEG NONE. 1B MODE REPLY 0 AJEKJ 04HEIGHT,STEP,FIRST FIRST STEP HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AJELD /D/ 07GUIDE,PINHOLE PINHOLE GUIDE AN INDICATION OF WHETHER OR NOT A PINHOLE USED AS A GUIDE TO POSITION THE ITEM IS INCLUDED. SELECT REPLY CODE 10AA49 AJEML 16STYLE,SECTION,FLANGE FLANGE SECTION STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FLANGE SECTION. 1L MODE REPLY 0 AJENA 12QUANTITY,HOLE,OUTER BOLT CIRCLE OUTER BOLT CIRCLE HOLE QUANTITY THE NUMBER OF HOLES PROVIDED ON THE OUTER BOLT CIRCLE OF THE ITEM. 1A MODE REPLY 0 AJEPA 12QUANTITY,HOLE,INNER BOLT CIRCLE INNER BOLT CIRCLE HOLE QUANTITY THE NUMBER OF HOLES PROVIDED ON THE INNER BOLT CIRCLE OF THE ITEM. 1A MODE REPLY 0 AJEQD 18TYPE,HOLE,REDUCER FLANGE REDUCER FLANGE HOLE TYPE INDICATES THE TYPE OF HOLE PROVIDED IN THE REDUCER FLANGE. SELECT REPLY CODE 10AB83 AJERJ 04DIAMETER FOR WHICH DESIGNED,INSIDE,HOSE HOSE INSIDE DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOSE FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJESJ 04DIAMETER FOR WHICH DESIGNED,OUTSIDE,HOSE HOSE OUTSIDE DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOSE FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJETJ 04THICKNESS,HEAD,WRENCHING END WRENCHING END HEAD THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJEUJ 04THICKNESS,HEAD,DRIVE END DRIVE END HEAD THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJEVD /D/ 19FINISH,SURFACE,SEATING SEATING SURFACE FINISH AN ADDITIONAL FINISHING PROCESS BY WHICH THE SURFACE OF AN ITEM WHICH CONTACTS ANOTHER SURFACE,GASKET,OR THE LIKE,IS ALTERED IN RESPECT TO POLISHING,GRINDING,AND THE LIKE. SELECT REPLY CODE 10AA41 AJEWD /D/ 07SURFACE,SEATING,SERRATED SERRATED SEATING SURFACE AN INDICATION OF WHETHER OR NOT THE SURFACE OF AN ITEM WHICH CONTACTS ANOTHER SURFACE,GASKET,OR THE LIKE,IS SERRATED. SELECT REPLY CODE 10AA89 AJEXD /D/ 14SHAPE,CROSS-SECTIONAL,GROOVE GROOVE CROSS-SECTIONAL SHAPE A GEOMETRIC CONFIGURATION OF THE GROOVE WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 AJEYJ 04DIAMETER,PITCH,GROOVE GROOVE PITCH DIAMETER THE PITCH DIAMETER OF THE GROOVE. 2D AND 1B MODE REPLY21AA051AC20 AJEZJ /D/ 04LENGTH,UNIT,PACKAGED PACKAGED UNIT LENGTH AN OVERALL MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM ENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AJFAJ /D/ 04WIDTH,UNIT,PACKAGED PACKAGED UNIT WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM ENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AJFBJ /D/ 04HEIGHT,UNIT,PACKAGED PACKAGED UNIT HEIGHT AN OVERALL MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN ITEM ENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AJFCJ 04DIAMETER,CORE,BODY BODY CORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY CORE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJFDJ 04DEPTH,CORE CORE DEPTH AN INSIDE MEASUREMENT BETWEEN SPECIFIED POINTS ON A CORE,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AJFEJ 04DIAMETER,FACE,WASHER WASHER FACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJFFJ 04THICKNESS,FACE,WASHER WASHER FACE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJFGJ 04DISTANCE,BLEEDER HOLE CENTER TO THREADED END BLEEDER HOLE CENTER TO THREADED END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AJFHJ 04DIAMETER,HOLE,BLEEDER BLEEDER HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJFJJ 04DIAMETER,CORE,HEAD HEAD CORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HEAD CORE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJFKJ 04HEIGHT,LUG LUG HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AJFLJ 04RADIUS,SPHERICAL SPHERICAL RADIUS A MEASUREMENT OF A LINE SEGMENT EXTENDING THE CURVATURE PORTION OF THE SPHERICAL SURFACE. 2D AND 1B MODE REPLY21AA051AC20 AJFMJ 04DISTANCE,END TO FLANGE END TO FLANGE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AJFNJ 04LENGTH,HOLE,CONCENTRIC CONCENTRIC HOLE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJFPJ 04RADIUS,END,FIRST LEG FIRST LEG END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJFQJ 04RADIUS,END,SECOND LEG SECOND LEG END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJFRJ 04RADIUS,SIDE,FIRST LEG FIRST LEG SIDE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJFSJ 04RADIUS,SIDE,SECOND LEG SECOND LEG SIDE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJFTJ /D/ 04DIAMETER,END,FLATTENED FLATTENED END DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJFUJ 04WIDTH,MAGNET MAGNET WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJFVJ 04LENGTH,PROJECTION,MAGNET MAGNET PROJECTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJFWL 16STYLE,END,DRIVE DRIVE END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE DRIVE END. 1L MODE REPLY 0 AJFXL 16STYLE,CONNECTION,END END CONNECTION STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END CONNECTION. 1L MODE REPLY 0 AJFYB 04ANGLE IN DEG,SEAT SEAT ANGLE IN DEG THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AJFZJ 04RADIUS,SEAT SEAT RADIUS THE RADIUS OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS. 2D AND 1B MODE REPLY21AA051AC20 AJGAD 09MATERIAL,BELLOWS BELLOWS MATERIAL THE ELEMENT, COMPOUND, OR MIXTURE OF WHICH THE BELLOWS ARE FABRICATED, EXCLUDING ANY SURFACE TREATMENT SELECT REPLY CODE 10MA01 AJGBD 09MATERIAL,BUSHING BUSHING MATERIAL THE ELEMENT, COMPOUND, OR MIXTURE OF WHICH THE BUSHING IS FABRICATED, EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10MA01 AJGCJ /D/ 10LIFT RATING,MAGNET MAGNET LIFT RATING THE MAGNET LIFT RATING AS INDICATED BY THE WEIGHT THAT THE MAGNET WILL RETAIN. 1D AND 1B MODE REPLY12AB16 AJGDD 18TYPE,HEAD HEAD TYPE INDICATES THE TYPE OF HEAD PROVIDED. SELECT REPLY CODE 10AE98 AJGED /D/ 18TYPE,BODY BODY TYPE INDICATES THE TYPE OF BODY PROVIDED. SELECT REPLY CODE 10AE98 AJGFD /D/ 03DESIGNATOR,GRADE,SIMPLIFIED,FLINT/EMERY FLINT/EMERY SIMPLIFIED GRADE DESIGNATOR A DESIGNATION INDICATING THE GENERAL CLASSIFICATION SIZE OF THE FLINT/EMERY ABRASIVE PARTICLES. SELECT REPLY CODE 10AF67 AJGGA /D/ 03DESIGNATOR,GRADE,ABRASIVE FINISHING/POLISHING ABRASIVE FINISHING/POLISHING GRADE DESIGNATOR A DESIGNATION INDICATING THE GENERAL SIZE OF THE ABRASIVE FINISHING/POLISHING PARTICLES. 1A MODE REPLY 0 AJGHA 03DESIGNATOR,SIZE,STEEL SHOT STEEL SHOT SIZE DESIGNATOR A DESIGNATION INDICATING THE SIZE OF THE STEEL SHOT SPHERICAL PARTICLES. 1A MODE REPLY 0 AJGJA 03DESIGNATOR,SIZE,SEDIMENTATION GRIT SEDIMENTATION GRIT SIZE DESIGNATOR A DESIGNATION INDICATING THE RATED SIZE OF THE INDIVIDUAL SEDIMENTATION GRIT PARTICLES. 1A MODE REPLY 0 AJGKJ 04RADIUS,TIP,BASE FLANGE BASE FLANGE TIP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJGLJ 04RADIUS WHERE LEFT FLANGE JOINS BASE FLANGE,FILLET FILLET RADIUS WHERE LEFT FLANGE JOINS BASE FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 AJGMJ 04RADIUS WHERE LEFT FLANGE JOINS BASE FLANGE,OUTER OUTER RADIUS WHERE LEFT FLANGE JOINS BASE FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 AJGNJ 04RADIUS,TOP,LEFT SIDE FLANGE LEFT SIDE FLANGE TOP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJGPJ 04THICKNESS,FLANGE,BASE BASE FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJGQJ 04WIDTH,FLANGE,BASE BASE FLANGE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BASE FLANGE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AJGRJ 04DIAMETER,TOP,LEFT SIDE FLANGE LEFT SIDE FLANGE TOP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJGSJ 04DIAMETER,TOP,RIGHT SIDE FLANGE RIGHT SIDE FLANGE TOP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJGTJ /D/ 04DISTANCE,OFFSET CENTER TO END OFFSET CENTER TO END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AJGUJ /D/ 04DEPTH,SLOT/GROOVE,FIRST FIRST SLOT/GROOVE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJGVJ 04HEIGHT,OFFSET,FIRST FIRST OFFSET HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AJGWJ 04RADIUS,OUTSIDE OUTSIDE RADIUS A MEASUREMENT OF A STRAIGHT LINE DRAWN FROM THE CENTER OF A CIRCLE TO ANY PART OF ITS CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJGXJ 04RADIUS WHERE RIGHT FLANGE JOINS BASE FLANGE,OUTER OUTER RADIUS WHERE RIGHT FLANGE JOINS BASE FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 AJGYJ 04RADIUS WHERE RIGHT FLANGE JOINS BASE FLANGE,FILLET FILLET RADIUS WHERE RIGHT FLANGE JOINS BASE FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 AJGZJ 04RADIUS,TOP,RIGHT SIDE FLANGE RIGHT SIDE FLANGE TOP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHAJ 04LENGTH,TAPER,LEFT SIDE FLANGE LEFT SIDE FLANGE TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHBJ 04LENGTH,TAPER,RIGHT SIDE FLANGE RIGHT SIDE FLANGE TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHCJ 04THICKNESS,TOP,LEFT SIDE TOP FLANGE LEFT SIDE TOP FLANGE TOP THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHDJ 04THICKNESS,TOP,RIGHT SIDE TOP FLANGE RIGHT SIDE TOP FLANGE TOP THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHEJ /D/ 04WIDTH,SLOT/GROOVE,FIRST FIRST SLOT/GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHFJ 04WIDTH,OFFSET,FIRST FIRST OFFSET WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHGB 04ANGLE IN DEG,FIRST FIRST ANGLE IN DEG NONE. 1B MODE REPLY 0 AJHHB 04ANGLE IN DEG,SECOND SECOND ANGLE IN DEG NONE. 1B MODE REPLY 0 AJHJJ 04DIAMETER,FIRST FIRST DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHKJ 04DIAMETER,SECOND SECOND DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHLJ /D/ 04DISTANCE,CENTER TO CENTER,ANCHOR FLANGE/BUTTON ANCHOR FLANGE/BUTTON CENTER TO CENTER DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHMJ 04DISTANCE,HOLE CENTER TO BASE HOLE CENTER TO BASE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHNJ 04DISTANCE,HOLE CENTER TO RIGHT SIDE HOLE CENTER TO RIGHT SIDE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHPJ /D/ 04DISTANCE,FIRST RIB CENTER TO BASE/FLANGE END FIRST RIB CENTER TO BASE/FLANGE END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHQJ 04DISTANCE,LOWER FLANGE EDGE TO BASE LOWER FLANGE EDGE TO BASE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHRJ /D/ 04DEPTH,SLOT/GROOVE,SECOND SECOND SLOT/GROOVE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHSJ 04HEIGHT,CUSHION CUSHION HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHTJ /D/ 04HEIGHT,LOWER PORTION,ANCHOR FLANGE/BUTTON ANCHOR FLANGE/BUTTON LOWER PORTION HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHUJ /D/ 04HEIGHT,UPPER PORTION,ANCHOR FLANGE/BUTTON ANCHOR FLANGE/BUTTON UPPER PORTION HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHVJ 04RADIUS,CORNER,FIRST FIRST CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHWJ 04RADIUS,CORNER,SECOND SECOND CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHXJ 04RADIUS,CORNER,THIRD THIRD CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHYJ 04RADIUS,FILLET,FIRST FIRST FILLET RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJHZJ 04RADIUS,FILLET,SECOND SECOND FILLET RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJJAJ 04RADIUS,GROOVE,FIRST FIRST GROOVE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJJBJ 04RADIUS,TIP,FIRST FIRST TIP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJJCJ /D/ 04THICKNESS,FLANGE,FIRST/TOP FIRST/TOP FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJJDJ /D/ 04THICKNESS,TIP/END,FIRST FIRST TIP/END THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJJEJ /D/ 04THICKNESS,TIP/END,SECOND SECOND TIP/END THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJJFJ 04THICKNESS,FLANGE,SECOND SECOND FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJJGJ 04WIDTH,ISTHMUS ISTHMUS WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJJHJ /D/ 04WIDTH,FLANGE,FIRST/TOP FIRST/TOP FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJJJJ 04WIDTH,FLANGE,SECOND SECOND FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJJKJ 04WIDTH,OFFSET,SECOND SECOND OFFSET WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJJLJ 04WIDTH,OFFSET,THIRD THIRD OFFSET WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJJMJ /D/ 04WIDTH,SLOT/GROOVE,SECOND SECOND SLOT/GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJJNJ 04WIDTH,TIP,FIRST FIRST TIP WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJJPJ 04THICKNESS,LEG LEG THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJJQJ 04HEIGHT,LEG,LEFT SIDE LEFT SIDE LEG HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AJJRJ 04HEIGHT,LEG,RIGHT SIDE RIGHT SIDE LEG HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AJJSJ 04DISTANCE,RIGHT SIDE OFFSET TO END RIGHT SIDE OFFSET TO END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AJJTB /D/ 10FINISH IN MICROINCHES,RMS,BODY SURFACE BODY SURFACE RMS FINISH IN MICROINCHES THE SPECIFIC ROOT MEAN SQUARE FINISH ON THE BODY SURFACE,EXPRESSED IN MICROINCHES. 1B MODE REPLY 0 AJJUB /D/ 10FINISH IN MICROINCHES,RMS,CONCENTRIC HOLE SURFACE CONCENTRIC HOLE SURFACE RMS FINISH IN MICROINCHES THE SPECIFIC ROOT MEAN SQUARE FINISH ON THE CONCENTRIC HOLE SURFACE,EXPRESSED IN MICROINCHES. 1B MODE REPLY 0 AJJVB /D/ 10FINISH IN MICROINCHES,RMS,FLANGE SURFACE FLANGE SURFACE RMS FINISH IN MICROINCHES THE SPECIFIC ROOT MEAN SQUARE FINISH ON THE FLANGE SURFACE,EXPRESSED IN MICROINCHES. 1B MODE REPLY 0 AJJWA 12QUANTITY,COMPONENT COMPONENT QUANTITY THE NUMBER OF COMPONENTS INCLUDED IN THE ITEM. 1A MODE REPLY 0 AJJXD 19ORIGIN,DOCUMENT,COMPONENT COMPONENT DOCUMENT ORIGIN THE ORIGINATOR /GOVERNMENTAL,INDUSTRIAL,OR OTHERWISE/ OF THE AVAILABLE DOCUMENT WHICH LISTS THE COMPONENT/S/ OF THE ITEM. SELECT REPLY CODE 10AF59 AJJYA 19SOURCE,DOCUMENT DOCUMENT SOURCE THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE GOVERNMENT AGENCY,INDUSTRIAL ORGANIZATION,OR OTHER SOURCE,WHICH CONTROLS THE DOCUMENT. 1A MODE REPLY 0 AJJZD 18TYPE,DOCUMENT DOCUMENT TYPE INDICATES THE TYPE OF DOCUMENT BY THE TITLE. SELECT REPLY CODE 10AF70 AJKAA 19IDENTIFICATION,DOCUMENT DOCUMENT IDENTIFICATION THE NUMBER OR SYMBOL USED TO IDENTIFY THE DOCUMENT. 1A MODE REPLY 0 AJKBA 19NUMBER,PAGE,COMPONENT DOCUMENT COMPONENT DOCUMENT PAGE NUMBER THE PAGE NUMBER INDICATING THE LOCATION OF THE COMPONENT/S/ LISTED IN THE DOCUMENT. 1A MODE REPLY 0 AJKCG 19ITEMS AND QUANTITIES,SUPPLY SUPPLY ITEMS AND QUANTITIES A LISTING OF THOSE MAJOR COMPONENTS WHICH ARE COMPRISED OF A NATIONAL STOCK NUMBER,AN ITEM NAME,STANDARDIZED NAME,OR PART NAME,AND THE NUMBER OF EACH. FULL TEXT WRITE-IN 0 AJKDG 19ITEMS AND QUANTITIES,NONSUPPLY NONSUPPLY ITEMS AND QUANTITIES A LISTING OF THOSE MAJOR COMPONENTS,OUTSIDE THE SCOPE OF AN ITEM OF SUPPLY TO BE CATALOGED,AS INDICATED BY THE NAME OF THE MANUFACTURER,AND THE NAME AND NUMBER OF THE ITEM AS IDENTIFIED BY THE MANUFACTURER,AND THE NUMBER OF EACH. FULL TEXT WRITE-IN 0 AJKEA 19SOURCE,ITEM,END END ITEM SOURCE THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE GOVERNMENT AGENCY,INDUSTRIAL ORGANIZATION,OR OTHER SOURCE,WHICH CONTROLS OR MANUFACTURES THE END ITEM. 1A MODE REPLY 0 AJKFD /D/ 18TYPE,CONTAINER CONTAINER TYPE INDICATES THE TYPE OF CONTAINER PROVIDED,SUCH AS BOX,CAN,CRATE,CHEST,AND THE LIKE,EXCLUDING OUTSIDE PACKAGING MATERIAL. PLEASE USE MRC ALQG IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AF72 AJKGD 09MATERIAL,INSULATOR INSULATOR MATERIAL THE ELEMENT, COMPOUND, OR MIXTURE OF WHICH THE INSULATOR IS FABRICATED. SELECT REPLY CODE 10MA01 AJKHG /D/ 03DESIGNATOR,IDENTIFICATION IDENTIFICATION DESIGNATOR A DESIGNATION ASSIGNED TO THE ITEM FOR PURPOSE OF READY IDENTIFICATION. PLEASE USE MRC BTXN IN PLACE OF THIS DISCONTINUED MRC. FULL TEXT WRITE-IN 0 AJKJD /D/ 09MATERIAL,LINING,FRICTION FRICTION LINING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FRICTION LINING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AJKKL 16STYLE,LINING LINING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LINING. 1L MODE REPLY 0 AJKLJ 04DIAMETER,DRUM DRUM DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A DRUM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJKMJ 04WIDTH,DRUM DRUM WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A DRUM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AJKNA /D/ 12QUANTITY,SEGMENT,LINING LINING SEGMENT QUANTITY THE NUMBER OF PIECES OF LINING ATTACHED TO THE BRAKE SHOE OR BAND. 1A MODE REPLY 0 AJKPA 12QUANTITY,CLIP,SUSPENSION ANCHOR SUSPENSION ANCHOR CLIP QUANTITY THE NUMBER OF SUSPENSION ANCHOR CLIPS INCLUDED. 1A MODE REPLY 0 AJKQD 18MEDIA TYPE,PUBLICATION PUBLICATION MEDIA TYPE AN INDICATION OF THE TYPE OF PUBLICATION MEDIA FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK95 AJKRJ /D/ 04DISTANCE BETWEEN SLOT CENTERS,ARC ARC DISTANCE BETWEEN SLOT CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJKSJ /D/ 04LENGTH BETWEEN LUG CENTERS,ARC ARC LENGTH BETWEEN LUG CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJKTJ 04DIAMETER,LUG LUG DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJKUJ 04DISTANCE,LUG CENTER TO LINING END LUG CENTER TO LINING END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AJKVJ /D/ 04DISTANCE,SLOT CENTER TO LINING END SLOT CENTER TO LINING END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AJKWJ 04LENGTH,ARC ARC LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJKXJ /D/ 04LENGTH,MINOR,ARC ARC MINOR LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJKYJ 04RADIUS,MINOR MINOR RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJKZL /D/ 16STYLE,IMPELLER IMPELLER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE IMPELLER. 1L MODE REPLY 0 AJLAA 12QUANTITY,TEETH TEETH QUANTITY THE NUMBER OF TEETH INCLUDED ON THE ITEM. 1A MODE REPLY 0 AJLBA 12QUANTITY,BLADE BLADE QUANTITY THE NUMBER OF INDIVIDUAL BLADES INCLUDED. 1A MODE REPLY 0 AJLCD /D/ 09MATERIAL,BLADE BLADE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BLADE IS FABRICATED. PLEASE USE MRC CYEM IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AJLDD /D/ 17SURFACE TREATMENT,BLADE BLADE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE BLADE SURFACE. PLEASE USE MRC AJBP IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AJLED 18TYPE,GUARD,IMPELLER IMPELLER GUARD TYPE INDICATES THE TYPE OF GUARD PROVIDED TO PROTECT THE IMPELLER FROM DAMAGE AND PERSONNEL FROM INJURY. SELECT REPLY CODE 10AF74 AJLFD /D/ 09MATERIAL,HOUSING HOUSING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HOUSING IS FABRICATED. SELECT REPLY CODE 10AD09 AJLGD 05DIRECTION,ROTATION,IMPELLER IMPELLER ROTATION DIRECTION THE DIRECTION OF ROTATION OF A ROTATING IMPELLER. SELECT REPLY CODE 10AC84 AJLHL /D/ 16STYLE,HUB,IMPELLER IMPELLER HUB STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE IMPELLER HUB. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 1L MODE REPLY 0 AJLJJ 04LENGTH,HUB HUB LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE HUB,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AJLKJ 04LENGTH,PROJECTION,HUB HUB PROJECTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJLLD 11METHOD,ATTACHMENT,IMPELLER IMPELLER ATTACHMENT METHOD THE MEANS USED TO ATTACH THE IMPELLER TO A ROTATABLE SHAFT. SELECT REPLY CODE 10AB47 AJLML /D/ 16STYLE,FAN FAN STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FAN. 1L MODE REPLY 0 AJLNJ /D/ 04DIAMETER,INSIDE,TUBE OR VENTURI RING TUBE OR VENTURI RING INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJLPJ 04LENGTH,FAN FAN LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJLQJ 04WIDTH,FAN FAN WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJLRJ 04HEIGHT,FAN FAN HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AJLSJ 04HEIGHT,SHORTEST SHORTEST HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AJLTJ 04HEIGHT,EXTENDED EXTENDED HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN OBJECT,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AJLUJ 04WIDTH,INSIDE,OUTLET OUTLET INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJLVJ 04HEIGHT,INSIDE,OUTLET OUTLET INSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AJLWJ 04DIAMETER,INSIDE,OUTLET OUTLET INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTLET,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJLXA 12QUANTITY,FAN FAN QUANTITY THE NUMBER OF INDIVIDUAL FANS CONTAINED IN THE ITEM. 1A MODE REPLY 0 AJLYJ 10PRESSURE AT SPECIFIED AIR FLOW RATE,STATIC STATIC PRESSURE AT SPECIFIED AIR FLOW RATE THE STATIC PRESSURE MEASURED AT THE AIR FLOW RATE SPECIFIED. 1D AND 1B MODE REPLY11AB18 AJLZD 19SUFFIX LETTER,FAILURE RATE FAILURE RATE SUFFIX LETTER THE SUFFIX LETTER FROM THE RELAYS MILITARY SPECIFICATION, INDICATING THE PERCENT FAILURE RATE LEVEL PER 10,000 CYCLES. SELECT REPLY CODE 10AE03 AJMAD /D/ 19DEGREE,INCLOSURE INCLOSURE DEGREE THE AMOUNT OR EXTENT OF THE INCLOSURE WHICH GUARDS,PROTECTS,COVERS,OR ENCASES THE ITEM. SELECT REPLY CODE 10AA59 AJMBD /D/ 07PROVISION,NONSPARKING NONSPARKING PROVISION AN INDICATION OF WHETHER OR NOT A PROVISION TO PREVENT SPARKING IS INCLUDED. SELECT REPLY CODE 10AA49 AJMCD /D/ 05DIRECTION,ADJUSTMENT ADJUSTMENT DIRECTION THE DIRECTION IN WHICH THE ITEM IS ADJUSTABLE. SELECT REPLY CODE 10AC60 AJMDD /D/ 07FEATURE,OSCILLATING OSCILLATING FEATURE AN INDICATION OF WHETHER OR NOT AN OSCILLATING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AJMED 08LOCATION,OUTLET OUTLET LOCATION INDICATES THE LOCATION OF THE OUTLET ON THE ITEM. SELECT REPLY CODE 10AE46 AJMFD /D/ 05DIRECTION,DISCHARGE DISCHARGE DIRECTION THE DIRECTION IN WHICH THE ITEM DISCHARGES DURING OPERATION. SELECT REPLY CODE 10AC60 AJMGD 07PITCH,BLADE BLADE PITCH AN INDICATION OF WHETHER OR NOT THE BLADE PITCH IS ADJUSTABLE. SELECT REPLY CODE 10AC06 AJMHD /D/ 14SHAPE,BLADE BLADE SHAPE THE PHYSICAL CONFIGURATION OF THE BLADE.PLEASE USE MRC CYMR IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD07 AJMJD 18TYPE,APPLICATION APPLICATION TYPE INDICATES THE TYPE OF APPLICATION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AF75 AJMKD /D/ 19MEDIUM,COOLING,BEARING BEARING COOLING MEDIUM THE COOLING MEDIUM USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE BEARINGS. USE MRC ACZV AND ISAC TO TABLE 0094 SELECT REPLY CODE 10AB75 AJMLD /D/ 07FLANGE,OUTLET OUTLET FLANGE AN INDICATION OF WHETHER OR NOT AN OUTLET FLANGE IS INCLUDED. SELECT REPLY CODE 10AA49 AJMMD /D/ 07DAMPER DAMPER AN INDICATION OF WHETHER OR NOT A DAMPER IS INCLUDED. SELECT REPLY CODE 10AA49 AJMND /D/ 11METHOD,FABRICATION,HOUSING HOUSING FABRICATION METHOD THE PROCESS USED IN MANUFACTURING THE HOUSING. SELECT REPLY CODE 10AA62 AJMPD /D/ 07SUITABILITY,SHIPMENT,AIRCRAFT AIRCRAFT SHIPMENT SUITABILITY AN INDICATION OF WHETHER OR NOT THE ITEM IS SUITABLE FOR SHIPMENT BY AIRCRAFT. SELECT REPLY CODE 10AA89 AJMQA 03DESIGNATOR,GRADE,ABRASIVE FLOUR ABRASIVE FLOUR GRADE DESIGNATOR A DESIGNATION OF THE SPECIFIED DEGREE OF FINENESS OF THE GROUND ABRASIVE FLOUR. 1A MODE REPLY 0 AJMRH 03DESIGNATOR,GRADE AND SIZE,STEEL GRIT STEEL GRIT GRADE AND SIZE DESIGNATOR A DESIGNATION OF THE GRADE AND SIZE OF THE ANGULAR STEEL GRIT PARTICLES PRODUCED BY CRUSHING CAST IRON OR HEAT TREATED STEEL SHOT. 2D MODE REPLY 22AF762AF77 AJMSA 03DESIGNATOR,SIZE,STANDARD MICRON,ABRASIVE ABRASIVE STANDARD MICRON SIZE DESIGNATOR A DESIGNATION OF THOSE ABRASIVE SIZES USUALLY PREPARED BY METHODS OF SEPARATION OTHER THAN BY SIEVING AND USUALLY SMALLER THAN SIEVE SIZES. 1A MODE REPLY 0 AJMTD 03DESIGNATOR,CONTENT,ABRASIVE SIZE ABRASIVE SIZE CONTENT DESIGNATOR A DESIGNATION OF THE CONTENT OF A MATERIAL IN SPECIFIC SIZES OF ABRASIVE PARTICLES. SELECT REPLY CODE 10AF78 AJMUA 12QUANTITY,POPPET POPPET QUANTITY THE NUMBER OF POPPETS PROVIDED. 1A MODE REPLY 0 AJMVA 03DESIGNATOR,SIZE,PARTICLE,AVERAGE AVERAGE PARTICLE SIZE DESIGNATOR A DESIGNATION INDICATING THE AVERAGE SIZE OF THE PARTICLES. 1A MODE REPLY 0 AJMWJ 10RISE,TEMP,MOTOR WINDINGS MOTOR WINDINGS TEMP RISE THE MAXIMUM PERMISSIBLE TEMPERATURE INCREASE IN THE MOTOR WINDINGS AS A RESULT OF ITS OPERATION UNDER NORMAL CONDITIONS. 1D AND 1B MODE REPLY11AB36 AJMXD 04SIZE,GARMENT GARMENT SIZE A DESIGNATION INDICATING ONE OF A SERIES OF GRADUATED CLASSIFICATIONS OF MANUFACTURED CLOTHING ITEMS IDENTIFIED BY NUMBER,LETTER,AND/OR WORD,EACH REPRESENTING A DIMENSION OR SET OF DIMENSIONS. SELECT REPLY CODE 10AF81 AJMYD /D/ 09MATERIAL,GARMENT,BASIC BASIC GARMENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MAIN BODY AND PRINCIPAL PARTS OF CLOTHING ITEMS ARE FABRICATED,EXCLUDING ANY SURFACE COATINGS. SELECT REPLY CODE 10AD09 AJMZD /D/ 19NAME,CLOTH,BASIC GARMENT BASIC GARMENT CLOTH NAME A NOUN,WITH OR WITHOUT MODIFIERS,BY WHICH THE CLOTH FROM WHICH THE MAIN BODY AND PRINCIPAL PARTS OF CLOTHING ITEMS ARE FABRICATED IS KNOWN OR DESIGNATED,EXCLUDING ANY SURFACE COATINGS. SELECT REPLY CODE 10AF82 AJNAD /D/ 09MATERIAL,LAYER,LAMINATED CLOTH LAMINATED CLOTH LAYER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INDIVIDUAL PLIES OF LAMINATED CLOTH ARE FABRICATED. SELECT REPLY CODE 10AD09 AJNBD /D/ 19NAME,CLOTH,LAMINATED CLOTH LAYER LAMINATED CLOTH LAYER CLOTH NAME A NOUN,WITH OR WITHOUT MODIFIERS,BY WHICH THE CLOTH FROM WHICH THE INDIVIDUAL PLIES OF LAMINATED CLOTH ARE FABRICATED,IS KNOWN OR DESIGNATED. SELECT REPLY CODE 10AF82 AJNCD /D/ 07FEATURE,REVERSIBLE REVERSIBLE FEATURE AN INDICATION OF WHETHER OR NOT A REVERSIBLE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AJNDD 19PATTERN,FABRIC FABRIC PATTERN AN ARTISTIC OR MECHANICAL DESIGN OR FIGURE THAT IS IMPRINTED ON,EMBODIED IN,OR OTHERWISE CAUSED TO BECOME AN INTEGRAL OR APPARENT PART OF THE FABRIC. SELECT REPLY CODE 10AF83 AJNED 19SOURCE,PATTERN PATTERN SOURCE THE NAME OF THE GOVERNMENT AGENCY,COMMERCIAL ORGANIZATION,OR MANUFACTURER CONTROLLING THE PATTERN DESIGNATOR. SELECT REPLY CODE 10AF94 AJNFA 19IDENTIFICATION,PATTERN PATTERN IDENTIFICATION A DESIGNATION ASSIGNED TO THE PATTERN FOR THE PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 AJNGD 19SOURCE,SHADE SHADE SOURCE THE NAME OF THE REFERENCE SOURCE OF THE SHADE IDENTIFICATION DESIGNATOR. SELECT REPLY CODE 10AF94 AJNHA 19IDENTIFICATION,DOCUMENT,SHADE SOURCE SHADE SOURCE DOCUMENT IDENTIFICATION THE NUMBER,SYMBOL,OR OTHER MEANS,USED TO IDENTIFY THE SHADE SOURCE DOCUMENT. 1A MODE REPLY 0 AJNJA 19IDENTIFICATION,SHADE SHADE IDENTIFICATION A DESIGNATION ASSIGNED TO A PARTICULAR GRADATION OF A COLOR FOR PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 AJNKD /D/ 07FEATURE,FLUORESCENT FLUORESCENT FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE IS INCLUDED TO BRING ABOUT BRIGHTNESS AND/OR PROVIDE CONTRAST IN DAYLIGHT AND UNDER BLACK-LIGHT CONDITIONS. SELECT REPLY CODE 10AA49 AJNLD 16STYLE,GARMENT GARMENT STYLE THE DESIGN OF THE BODY OF THE GARMENT EXCLUDING THE STYLE OF SLEEVES,CUFFS,COLLAR,AND THE LIKE. SELECT REPLY CODE 10AF71 AJNMD 04LENGTH,GARMENT GARMENT LENGTH THE LENGTH OF A GARMENT WITH REFERENCE TO THE PART OF THE BODY THE GARMENT REACHES. SELECT REPLY CODE 10AF68 AJNND 11METHOD,CLOSING,GARMENT GARMENT CLOSING METHOD THE MEANS BY WHICH THE PRINCIPAL OPENING OF THE GARMENT IS CLOSED. SELECT REPLY CODE 10AF69 AJNPD /D/ 07FLY,GARMENT GARMENT FLY AN INDICATION OF WHETHER OR NOT THE GARMENT HAS A FLEXIBLE PART WHICH CONCEALS THE FASTENING ATTACHED ADJACENT TO THE PRINCIPAL OPEINING. SELECT REPLY CODE 10AA49 AJNQD /D/ 08LOCATION,DEVICE,CLOSING CLOSING DEVICE LOCATION INDICATES THE LOCATION OF THE CLOSING DEVICE ON THE ITEM. SELECT REPLY CODE 10AE46 AJNRD 11METHOD,ADJUSTING,WAIST WAIST ADJUSTING METHOD THE MEANS USED TO REGULATE THE FIT OF A GARMENT AT THE WAIST. SELECT REPLY CODE 10AF69 AJNSD 04LENGTH,SLEEVE,GARMENT GARMENT SLEEVE LENGTH THE LENGTH OF THE SLEEVE WITH REFERENCE TO THE PART OF THE ARM IT REACHES. SELECT REPLY CODE 10AF84 AJNTD 18TYPE,CUFF,SLEEVE SLEEVE CUFF TYPE INDICATES THE TYPE OF CUFF BY THE STYLE OR FINISH OF THE LOWER SECTION OF THE SLEEVE. SELECT REPLY CODE 10AF85 AJNUD 11METHOD,CLOSING,CUFF CUFF CLOSING METHOD THE MEANS BY WHICH THE CUFF IS CLOSED. SELECT REPLY CODE 10AF69 AJNVD /D/ 07LOOPS,SHOULDER SHOULDER LOOPS AN INDICATION OF WHETHER OR NOT STRAPS ARE INCLUDED THAT ARE ATTACHED AT THE SLEEVE HEAD EXTENDING INWARD AND ARE BUTTONED NEAR THE EDGE OF THE COLLAR. SELECT REPLY CODE 10AA49 AJNWD /D/ 07LOOPS,MARK,SHOULDER SHOULDER MARK LOOPS AN INDICATION OF WHETHER OR NOT STRAPS USED TO HOLD A SHOULDER MARK ARE INCLUDED THAT ARE ATTACHED AT RIGHT ANGLES TO THE SHOULDER SEAM USUALLY IN PAIRS AND POSITIONED MIDWAY BETWEEN THE SLEEVE HEAD SEAM AND THE EDGE OF THE COLLAR. SELECT REPLY CODE 10AA49 AJNXD 19DEGREE,LINING LINING DEGREE THE EXTENT OF THE LINING WHICH COVERS THE INNER SURFACE OF THE ITEM. SELECT REPLY CODE 10AF86 AJNYD /D/ 09MATERIAL,LINING LINING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LINING IS FABRICATED. SELECT REPLY CODE 10AD09 AJNZD /D/ 19NAME,CLOTH,LINING LINING CLOTH NAME A NOUN,WITH OR WITHOUT MODIFIERS,BY WHICH THE CLOTH USED TO COVER THE INNER SURFACE OF AN ITEM IS KNOWN OR DESIGNATED. SELECT REPLY CODE 10AF82 AJPAD 18TYPE,BELT,GARMENT GARMENT BELT TYPE INDICATES THE TYPE OF BELT BY THE STYLE OR DESIGN OF THE SEPARATE STRIP OR BAND PLACED AROUND THE WAIST OF A GARMENT. SELECT REPLY CODE 10AF88 AJPBD 18TYPE,COLLAR,GARMENT GARMENT COLLAR TYPE INDICATES THE TYPE OF COLLAR BY THE STYLE OR DESIGN OF THAT PORTION OF A GARMENT THAT ENCIRCLES THE NECK. SELECT REPLY CODE 10AF89 AJPCD /D/ 09MATERIAL,COLLAR,GARMENT GARMENT COLLAR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE COLLAR OF A GARMENT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AJPDD /D/ 19NAME,CLOTH,COLLAR COLLAR CLOTH NAME A NOUN,WITH OR WITHOUT MODIFIERS,BY WHICH THE CLOTH FROM WHICH THE COLLAR IS FABRICATED IS KNOWN OR DESIGNATED. SELECT REPLY CODE 10AF82 AJPED /D/ 07HOOD HOOD AN INDICATION OF WHETHER OR NOT A HOOD IS INCLUDED. SELECT REPLY CODE 10AA49 AJPFD /D/ 07REMOVABILITY,HOOD HOOD REMOVABILITY AN INDICATION OF WHETHER OR NOT THE HOOD IS REMOVABLE. SELECT REPLY CODE 10AC29 AJPGD 11METHOD,ATTACHMENT,REMOVABLE HOOD REMOVABLE HOOD ATTACHMENT METHOD THE MEANS BY WHICH A REMOVABLE HOOD IS FASTENED TO AN ITEM. SELECT REPLY CODE 10AF69 AJPHD 11METHOD,CLOSING,GARMENT HOOD GARMENT HOOD CLOSING METHOD THE MEANS BY WHICH THE HOOD IS CLOSED AROUND THE CHIN AND NECK. SELECT REPLY CODE 10AF69 AJPJD /D/ 07VISOR,HOOD HOOD VISOR AN INDICATION OF WHETHER OR NOT A HOOD VISOR IS INCLUDED. SELECT REPLY CODE 10AA49 AJPKD /D/ 07RUFF,FUR,HOOD HOOD FUR RUFF AN INDICATION OF WHETHER OR NOT THE FACE APERTURE OF A HOOD IS TRIMMED WITH FUR. SELECT REPLY CODE 10AA49 AJPLD 18TYPE,POCKET POCKET TYPE INDICATES THE TYPE OF POCKET BY THE STYLE OR DESIGN. SELECT REPLY CODE 10AF87 AJPMA 12QUANTITY,POCKET POCKET QUANTITY THE NUMBER OF POCKETS INCLUDED IN THE ITEM. 1A MODE REPLY 0 AJPND /D/ 07PAD PAD AN INDICATION OF WHETHER OR NOT A CUSHIONING DEVICE IS INCLUDED IN OR ON THE ITEM. SELECT REPLY CODE 10AA49 AJPPJ /D/ 04DIAMETER,EXTENDED,MAXIMUM MAXIMUM EXTENDED DIAMETER THE MAXIMUM EXTENDED DIAMETER FOR WHICH THE SPRING IS DESIGNED. 1D AND 1B MODE REPLY11AA05 AJPQD /D/ 07REMOVABILITY,PAD PAD REMOVABILITY AN INDICATION OF WHETHER OR NOT THE CUSHIONING DEVICE IS REMOVABLE. SELECT REPLY CODE 10AC29 AJPRD /D/ 08LOCATION,PAD PAD LOCATION INDICATES THE LOCATION OF THE CUSHIONING DEVICE(S) IN OR ON THE ITEM. SELECT REPLY CODE 10AE46 AJPSD /D/ 07LINER LINER AN INDICATION OF WHETHER OR NOT A LINER IS FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AA55 AJPTD /D/ 09MATERIAL,LINER LINER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LINER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AJPUD /D/ 19NAME,CLOTH,LINER LINER CLOTH NAME A NOUN,WITH OR WITHOUT MODIFIERS,BY WHICH THE CLOTH FROM WHICH THE LINER IS FABRICATED IS KNOWN OR DESIGNATED. SELECT REPLY CODE 10AF82 AJPVD /D/ 19DEGREE,LINING,LINER LINER LINING DEGREE THE EXTENT OF THE LINING WHICH COVERS THE INNER SURFACE OF THE LINER. SELECT REPLY CODE 10AF86 AJPWD /D/ 09MATERIAL,LINING,LINER LINER LINING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LINER LINING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AJPXD /D/ 19NAME,CLOTH,LINER LINING LINER LINING CLOTH NAME A NOUN,WITH OR WITHOUT MODIFIERS,BY WHICH THE CLOTH USED TO COVER THE INNER SURFACE OF THE LINER IS KNOWN OR DESIGNATED. SELECT REPLY CODE 10AF82 AJPYD 11METHOD,ATTACHMENT,LINER LINER ATTACHMENT METHOD THE MEANS BY WHICH THE LINER IS FASTENED TO AN ITEM. SELECT REPLY CODE 10AF69 AJPZD /D/ 07FEATURE,REDUCING,STATIC ELECTRICITY STATIC ELECTRICITY REDUCING FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES THE ABILITY TO EXHIBIT REDUCED GENERATION OF STATIC ELECTRICITY. SELECT REPLY CODE 10AA49 AJQAD /D/ 03DESIGNATOR,WEIGHT,GARMENT GARMENT WEIGHT DESIGNATOR A DESIGNATION INDICATING THE HEAVINESS OF THE GARMENT. PLEASE USE MRC APWG WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AF07 AJQBD 19MARKING,REFLECTORIZED REFLECTORIZED MARKING THE LIGHT REFLECTING MARKING/S/ INCLUDED ON AN ITEM FOR THE PURPOSE OF OFFERING INSTRUCTIONS OR WARNINGS OR TO INDICATE THE PURPOSE,FUNCTION,OR APPLICATION OF THE ITEM. SELECT REPLY CODE 10AF91 AJQCD /D/ 19USER USER A DESIGNATION INDICATING THE PERSONNEL,ORGANIZATION,PROFESSION,TRADE,AND THE LIKE /EXCEPT ARMY,AIR FORCE,MARINE CORPS,AND NAVY/,FOR WHICH AN ITEM IS SPECIFICALLY DESIGNED. PLEASE USE MRC APXA IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AF92 AJQDD /D/ 07SHIELDING INCLUDED,FILAMENT FILAMENT SHIELDING INCLUDED AN INDICATION OF WHETHER OR NOT A FIXED SHIELD PROVIDED FOR CONTROLLING THE BEAM PATTERN PRODUCED BY THE LIGHT SOURCE IS INCLUDED. SELECT REPLY CODE 10AA89 AJQED 19TRANSPARENCY,MATERIAL MATERIAL TRANSPARENCY THE ABILITY OF THE MATERIAL TO TRANSMIT LIGHT AND ALLOW VISUAL PERCEPTION. SELECT REPLY CODE 10AF93 AJQFJ /D/ 04DIAMETER EXCLUDING PROTRUSIONS DIAMETER EXCLUDING PROTRUSIONS THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY EXCLUDING PROTRUSIONS,SUCH AS MOUNTING FACILITIES,PROJECTIONS,TERMINALS,AND THE LIKE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJQGD /D/ 19SOURCE,DESIGNATOR,COLOR PATTERN COLOR PATTERN DESIGNATOR SOURCE THE NAME OF THE GOVERNMENT AGENCY,COMMERCIAL ORGANIZATION,OR MANUFACTURER CONTROLLING THE COLOR PATTERN DESIGNATOR. SELECT REPLY CODE 10AF94 AJQHJ /D/ 10LOAD IN OHMS,ELECTRICAL ELECTRICAL LOAD IN OHMS THE OPPOSITION TO THE EFFECTIVE TRANSFERENCE OF POWER,EXPRESSED IN OHMS. 2D AND 1B MODE REPLY21AG141AC20 AJQJA /D/ 03DESIGNATOR,IDENTIFICATION,COLOR PATTERN COLOR PATTERN IDENTIFICATION DESIGNATOR A DESIGNATION ASSIGNED TO A PARTICULAR COLOR PATTERN FOR THE PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 AJQKD /D/ 13THREAD LOCATION,SCREW SCREW THREAD LOCATION AN INDICATION OF WHETHER THE SCREW THREAD IS LOCATED EXTERNALLY OR INTERNALLY. SELECT REPLY CODE 10AE46 AJQLJ 04DIAMETER,TOP TOP DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CIRCULAR TOP, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJQMJ 04DIAMETER,BOWL BOWL DIAMETER THE LENGTH OF A STRIAGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOWL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJQNJ 04DIAMETER,POST,LARGE END LARGE END POST DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGE END OF THE POST,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJQPJ 04DIAMETER,POST,SMALL END SMALL END POST DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALL END OF THE POST,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJQQD /D/ 07RESISTOR,VARIABLE VARIABLE RESISTOR AN INDICATION OF WHETHER OR NOT A VARIABLE RESISTOR IS INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA49 AJQRA /D/ 19CODE,MANUFACTURER,VARIABLE RESISTOR VARIABLE RESISTOR MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE VARIABLE RESISTOR. 1A MODE REPLY 0 AJQSA /D/ 19NUMBER,PART,VARIABLE RESISTOR MANUFACTURER VARIABLE RESISTOR MANUFACTURER PART NUMBER THE IDENTIFYING PART NUMBER ASSIGNED TO THE VARIBLE RESISTOR BY THE MANUFACTURER. 1A MODE REPLY 0 AJQTJ 04LENGTH,DEVICE,RETAINING RETAINING DEVICE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION BETWEEN THE EXTREME ENDS OF THE RETAINING DEVICE. 2D AND 1B MODE REPLY21AA051AC20 AJQUD 18TYPE,POINTER POINTER TYPE INDICATES THE TYPE OF INSTRUCTIONAL POINTER. SELECT REPLY CODE 10AB87 AJQVJ 04DISTANCE BETWEEN MOUNTING HOLES ALONG DEPTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES ALONG DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJQWD /D/ 18TYPE,END,FIRST TERMINAL FIRST TERMINAL END TYPE INDICATES THE TYPE OF TERMINATING PART(S) ATTACHED TO THE FIRST END OF THE ITEM. SELECT REPLY CODE 10AF95 AJQXD /D/ 18TYPE,END,SECOND TERMINAL SECOND TERMINAL END TYPE INDICATES THE TYPE OF TERMINATING PART(S) ATTACHED TO THE SECOND END OF THE ITEM. SELECT REPLY CODE 10AF95 AJQYJ 04DISTANCE,POINTER POINTER DISTANCE THE OVERALL LENGTH OF THE POINTER TO INCLUDE THE TELESCOPING RANGE AND/OR THE DISTANCE TO THE EXTREME END OF A LIGHT BEAM. 2D AND 1B MODE REPLY21AA051AC20 AJQZJ /D/ 04DISTANCE BETWEEN MOUNTING HOLES ALONG WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJRAJ /D/ 04WIDTH,OPENING,MINOR,LOWER LOOP LOWER LOOP MINOR OPENING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJRBJ 04DIAMETER,MATERIAL MATERIAL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MATERIAL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJRCJ /D/ 04WIDTH,OPENING,MAJOR,LOWER LOOP LOWER LOOP MAJOR OPENING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJRDJ /D/ 04DISTANCE,PIN CENTER TO LEG END PIN CENTER TO LEG END DISTANCE NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 2D AND 1B MODE REPLY21AA051AC20 AJREJ 04DISTANCE,BEARING SURFACE TO BEARING SURFACE BEARING SURFACE TO BEARING SURFACE DISTANCE NONE.MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 2D AND 1B MODE REPLY21AA051AC20 AJRFJ 04HEIGHT,FLANGE SEAT TO DISK END FLANGE SEAT TO DISK END HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AJRGJ /D/ 04WIDTH,OPENING,MINOR,UPPER LOOP UPPER LOOP MINOR OPENING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJRHJ /D/ 04WIDTH,OPENING,MAJOR,UPPER LOOP UPPER LOOP MAJOR OPENING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJRJJ /D/ 04WIDTH,OPENING,THROAT THROAT OPENING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJRKJ 04WIDTH,INSIDE,MAJOR MAJOR INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJRLJ 04WIDTH,INSIDE,MINOR MINOR INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJRMJ 04HEIGHT,FLANGE,UNDER UNDER FLANGE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AJRND /D/ 09MATERIAL,FACE FACE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FACE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AJRPJ 04WIDTH BETWEEN EYES,INSIDE INSIDE WIDTH BETWEEN EYES NONE. 2D AND 1B MODE REPLY21AA051AC20 AJRQJ /D/ 10HARDNESS RATING,BODY BODY HARDNESS RATING A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF THE BODY WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE. 2D AND 1B MODE REPLY21AC202AC26 AJRRJ /D/A16STYLE AND LOCATION,ATTACHMENT ATTACHMENT STYLE AND LOCATION THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ATTACHMENT AND ITS LOCATION. 1D AND 1A MODE REPLY12AE46 AJRSJ /D/ 04DIMENSIONS,STYLE,ATTACHMENT ATTACHMENT STYLE DIMENSIONS THOSE MEASURED DISTANCES WHICH ARE CHARACTERISTIC OF THE ITEM AND ESTABLISH ITS PHYSICAL LIMITS. 3D AND 1B MODE REPLY31AA051AC204AF96 AJRTJ /D/ 04DISTANCE,CENTER TO CENTER,U-BOLT U-BOLT CENTER TO CENTER DISTANCE NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 2D AND 1B MODE REPLY21AA051AC20 AJRUA 12QUANTITY,CLUTCH SETTING CLUTCH SETTING QUANTITY THE NUMERIC QUANTITY FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 AJRVJ /D/ 04LENGTH,U-BOLT U-BOLT LENGTH NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 2D AND 1B MODE REPLY21AA051AC20 AJRWJ 04LENGTH,TAKE-UP TAKE-UP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TAKE-UP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AJRXJ /D/ 04DIAMETER,STOCK,LINK LINK STOCK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJRYJ /D/ 04DIAMETER,STOCK,JAW JAW STOCK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJRZJ /D/ 04WIDTH BETWEEN JAWS WIDTH BETWEEN JAWS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJSAJ /D/ 10HARDNESS RATING,FACE FACE HARDNESS RATING A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF THE FACE OF THE ITEM WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE. 2D AND 1B MODE REPLY21AC202AC26 AJSBD /D/ 14SHAPE,SURFACE,SEATING SEATING SURFACE SHAPE THE PHYSICAL CONFIGURATION OF THE SURFACE OF THE SEAT. SELECT REPLY CODE 10AD07 AJSCJ /D/ 04DIAMETER,HOLE,WIRE ROPE WIRE ROPE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJSDJ 04WIDTH,SPAN,FORK FORK SPAN WIDTH THE DISTANCE LATERALLY FROM TIP TO TIP OF THE FORK. 2D AND 1B MODE REPLY21AA051AC20 AJSEJ 04DIAMETER,SLEEVE SLEEVE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SLEEVE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJSFJ /D/ 04LENGTH,SHANK,SLEEVE SLEEVE SHANK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJSGJ 04ANGLE IN DEG,SEAT SEAT ANGLE IN DEG THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 AJSHD 18TYPE,ACCOMMODATION,SEAL SEAL ACCOMMODATION TYPE INDICATES THE TYPE OF SEAL ACCOMMODATION INCLUDED IN OR ON THE ITEM. SELECT REPLY CODE 10AB80 AJSJJ /D/A16STYLE AND LOCATION,STEP STEP STYLE AND LOCATION THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE STEP AND ITS LOCATION. 1D AND 1A MODE REPLY13AJ91 AJSKJ /D/ 19DIMENSIONS,STYLE,STEP STEP STYLE DIMENSIONS THOSE MEASURED DISTANCES WHICH ARE CHARACTERISTIC OF THE ITEM AND ESTABLISH ITS PHYSICAL LIMITS. 3D AND 1B MODE REPLY31AF981AC202AF97 AJSLA 04SIZE,BODY BODY SIZE AN ALPHA AND/OR NUMERIC DESIGNATION INDICATING THE SIZE BY WHICH THE BODY IS IDENTIFIED. 1A MODE REPLY 0 AJSMD /D/ 19RECIPIENT,EXCITATION,PRIMARY PRIMARY EXCITATION RECIPIENT THE PRIMARY PART TO WHICH ENERGY IS APPLIED. SELECT REPLY CODE 10AF99 AJSNJ 10VOLTAGE RATING IN VOLTS,INPUT,STATOR STATOR INPUT VOLTAGE RATING IN VOLTS THE VALUE OF THE PRIMARY EXCITATION VOLTAGE FOR WHICH THE STATOR IS RATED,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 AJSPJ 10CURRENT RATING,INPUT,STATOR STATOR INPUT CURRENT RATING THE VALUE OF THE PRIMARY EXCITATION CURRENT FOR WHICH THE STATOR IS RATED,WITH ROTOR /SECONDARY/ CIRCUIT OPEN. 2D AND 1B MODE REPLY21AC301AC20 AJSQJ 10POWER RATING,ELECTRICAL,STATOR INPUT STATOR INPUT ELECTRICAL POWER RATING THE VALUE OF THE PRIMARY /ELECTRICAL/ EXCITATION POWER FOR WHICH THE STATOR IS RATED. 2D AND 1B MODE REPLY21AC331AC20 AJSRJ 10VOLTAGE RATING IN VOLTS,INPUT,ROTOR ROTOR INPUT VOLTAGE RATING IN VOLTS THE VALUE OF THE PRIMARY EXCITATION VOLTAGE FOR WHICH THE ROTOR IS RATED,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 AJSSJ 10FREQUENCY IN HERTZ FREQUENCY IN HERTZ THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT. 1D AND 1B MODE REPLY11AC20 AJSTJ 10CURRENT RATING,INPUT,ROTOR ROTOR INPUT CURRENT RATING THE VALUE OF THE PRIMARY EXCITATION CURRENT FOR WHICH THE ROTOR IS RATED,WITH STATOR /SECONDARY/ CIRCUIT OPEN. 2D AND 1B MODE REPLY21AC301AC20 AJSUA 10BUFFER SIZE IN MICRONS/MICROMETERS BUFFER SIZE IN MICRONS/MICROMETERS THE BUFFER SIZE EXPRESSED IN MICRONS/MICROMETERS. 1A MODE REPLY 0 AJSVJ 10POWER RATING,ELECTRICAL,ROTOR INPUT ROTOR INPUT ELECTRICAL POWER RATING THE VALUE OF THE PRIMARY /ELECTRICAL/ EXCITATION POWER FOR WHICH THE ROTOR IS RATED. 2D AND 1B MODE REPLY21AC331AC20 AJSWJ 10RESISTANCE IN OHMS,ZRO ZRO RESISTANCE IN OHMS THE RESISTANCE /R/ PART OF THE ROTOR IMPEDANCE WITH THE STATOR OPEN /ZRO/,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 AJSXJ /D/ 10REACTANCE IN OHMS,ZRO ZRO REACTANCE IN OHMS THE REACTANCE /X/ PART OF THE ROTOR IMPEDANCE WITH THE STATOR OPEN /ZRO/,EXPRESSED IN OHMS. 2D AND 1B MODE REPLY22AG001AC20 AJSYJ 10RESISTANCE IN OHMS,ZSO ZSO RESISTANCE IN OHMS THE RESISTANCE /R/ PART OF THE STATOR IMPEDANCE WITH THE ROTOR OPEN /ZSO/,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 AJSZJ /D/ 10REACTANCE IN OHMS,ZSO ZSO REACTANCE IN OHMS THE REACTANCE (X) PART OF THE STATOR IMPEDANCE WITH THE ROTOR OPEN (ZSO),EXPRESSED IN OHMS. 2D AND 1B MODE REPLY21AC202AG00 AJTAJ 10RESISTANCE IN OHMS,ZRS ZRS RESISTANCE IN OHMS THE RESISTANCE /R/ PART OF THE ROTOR IMPEDANCE WITH THE STATOR SHORTED /ZRS/,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 AJTBJ /D/ 10REACTANCE IN OHMS,ZRS ZRS REACTANCE IN OHMS THE REACTANCE /X/ PART OF THE ROTOR IMPEDANCE WITH THE STATOR SHORTED /ZRS/,EXPRESSED IN OHMS. 2D AND 1B MODE REPLY22AG001AC20 AJTCJ 10RESISTANCE IN OHMS,ZSS ZSS RESISTANCE IN OHMS THE RESISTANCE /R/ PART OF THE STATOR IMPEDANCE WITH THE ROTOR SHORTED /ZSS/,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 AJTDJ /D/ 10REACTANCE IN OHMS,ZSS ZSS REACTANCE IN OHMS THE REACTANCE /X/ PART OF THE STATOR IMPEDANCE WITH THE ROTOR SHORTED /ZSS/,EXPRESSED IN OHMS. 2D AND 1B MODE REPLY22AG001AC20 AJTEJ 10RESISTANCE IN OHMS,ZSO-90 ZSO-90 RESISTANCE IN OHMS THE RESISTANCE /R/ PART OF THE STATOR IMPEDANCE WITH THE ROTOR OPEN AND DISPLACED 90 DEGREES FROM ZERO /ZSO-90/,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 AJTFJ /D/ 10REACTANCE IN OHMS,ZSO-90 ZSO-90 REACTANCE IN OHMS THE REACTANCE /X/ PART OF THE STATOR IMPEDANCE WITH THE ROTOR OPEN AND DISPLACED 90 DEGRESS FROM ZERO /ZSO-90/,EXPRESSED IN OHMS. 2D AND 1B MODE REPLY22AG001AC20 AJTGJ 10MAGNITUDE IN OHMS,IMPEDANCE,ZRO ZRO IMPEDANCE MAGNITUDE IN OHMS THE MAGNITUDE PART /Z/ OF THE ROTOR IMPEDANCE WITH THE STATOR OPEN /ZRO/,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 AJTHJ 04ANGLE IN DEG,IMPEDANCE,ZRO ZRO IMPEDANCE ANGLE IN DEG THE ANGLE PART /O/ OF THE ROTOR IMPEDANCE WITH THE STATOR OPEN /ZRO/,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 AJTJJ 10MAGNITUDE IN OHMS,IMPEDANCE,ZSO ZSO IMPEDANCE MAGNITUDE IN OHMS THE MAGNITUDE PART /Z/ OF THE STATOR IMPEDANCE WITH THE ROTOR OPEN /ZSO/,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 AJTKJ 04ANGLE IN DEG,IMPEDANCE,ZSO ZSO IMPEDANCE ANGLE IN DEG THE ANGLE PART /O/ OF THE STATOR IMPEDANCE WITH THE ROTOR OPEN /ZSO/,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 AJTLJ 10MAGNITUDE IN OHMS,IMPEDANCE,ZRS ZRS IMPEDANCE MAGNITUDE IN OHMS THE MAGNITUDE PART /Z/ OF THE ROTOR IMPEDANCE WITH THE STATOR SHORTED /ZRS/,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 AJTMJ 04ANGLE IN DEG,IMPEDANCE,ZRS ZRS IMPEDANCE ANGLE IN DEG THE ANGLE PART /O/ OF THE ROTOR IMPEDANCE WITH THE STATOR SHORTED /ZRS/,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 AJTNJ 10MAGNITUDE IN OHMS,IMPEDANCE,ZSS ZSS IMPEDANCE MAGNITUDE IN OHMS THE MAGNITUDE PART /Z/ OF THE STATOR IMPEDANCE WITH THE ROTOR SHORTED /ZSS/,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 AJTPJ 04ANGLE IN DEG,IMPEDANCE,ZSS ZSS IMPEDANCE ANGLE IN DEG THE ANGLE PART /O/ OF THE STATOR IMPEDANCE WITH THE ROTOR SHORTED /ZSS/,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 AJTQJ 10MAGNITUDE IN OHMS,IMPEDANCE,ZSO-90 ZSO-90 IMPEDANCE MAGNITUDE IN OHMS THE MAGNITUDE PART /Z/ OF THE STATOR IMPEDANCE WITH THE ROTOR OPEN AND DISPLACED 90 DEGREES FROM ZERO /ZS0-90/,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 AJTRJ 04ANGLE IN DEG,IMPEDANCE,ZSO-90 ZSO-90 IMPEDANCE ANGLE IN DEG THE ANGLE PART /O/ OF THE STATOR IMPEDANCE WITH THE ROTOR OPEN AND DISPLACED 90 DEGREES FROM ZERO /ZSO-90/,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 AJTSJ 10RESISTANCE IN OHMS,DC,ROTOR ROTOR DC RESISTANCE IN OHMS THE OPPOSITION THAT THE ROTOR OFFERS TO THE FLOW OF THE DIRECT CURRENT,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 AJTTJ 10RESISTANCE IN OHMS,DC,STATOR STATOR DC RESISTANCE IN OHMS THE OPPOSITION THAT THE STATOR OFFERS TO THE FLOW OF DIRECT CURRENT,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 AJTUD 18TYPE,OPTICAL FIBER OPTICAL FIBER TYPE THE TYPE OF OPTICAL FIBER IN THE CONDUCTOR. SELECT REPLY CODE 10AK75 AJTVJ /D/ 10RATIO,TRANSFORMATION TRANSFORMATION RATIO THE RATIO OF THE OUTPUT VOLTAGE TO THE INPUT VOLTAGE AT MAXIMUM COUPLING. 3D AND 1B MODE REPLY32AG012AG021AC20 AJTWJ 10RATIO EQUALITY IN PERCENT,TRANSFORMATION TRANSFORMATION RATIO EQUALITY IN PERCENT THE VARIATION OF THE TRANSFORMATION RATIO FOR ALL POSSIBLE COMBINATIONS OF STATOR,ROTOR,AND COMPENSATING WINDINGS,EXPRESSED IN PERCENT. 1D AND 1B MODE REPLY11AC20 AJTXD 11METHOD,COMPENSATION COMPENSATION METHOD THE MEANS UTILIZED TO VARY THE LEVEL OF SIGNAL INPUT OR RESPONSE TO ATTAIN THE DESIRED OPERATIONAL ACTION. SELECT REPLY CODE 10AG03 AJTYJ 10RESISTANCE IN OHMS,ZCO ZCO RESISTANCE IN OHMS THE RESISTANCE PART /R/ OF THE COMPENSATOR IMPEDANCE WITH THE ROTOR OPEN /ZCO/,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 AJTZJ /D/ 10REACTANCE IN OHMS,ZCO ZCO REACTANCE IN OHMS THE REACTANCE /X/ PART OF THE COMPENSATOR IMPEDANCE WITH THE ROTOR OPEN /ZCO/,EXPRESSED IN OHMS. 2D AND 1B MODE REPLY22AG001AC20 AJUAA 10WAVELENGTH IN NANOMETERS WAVELENGTH IN NANOMETERS THE WAVELENGTH MEASURED IN NANOMETERS. 1A MODE REPLY 0 AJUBG 12SIZE AND QUANTITY,BIT BIT SIZE AND QUANTITY THE SIZE AND QUANTITY OF BITS INCLUDED. FULL TEXT WRITE-IN 0 AJUCA 19NUMBER,CLASSIFICATION,AMERICAN HOSPITAL FORMULARY SERVICE AMERICAN HOSPITAL FORMULARY SERVICE CLASSIFICATION NUMBER AN INDICATION OF THE AMERICAN HOSPITAL FORMULARY SERVICE CLASSIFICATION NUMBER OF THE ITEM. 1A MODE REPLY 0 AJUDL 16STYLE,ATTACHMENT,END END ATTACHMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END ATTACHMENT. 1L MODE REPLY 0 AJUEJ /D/ 04LENGTH,CROSS-SECTIONAL,BARB BARB CROSS-SECTIONAL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CROSS-SECTION, IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AJUFJ 04WIDTH,CROSS-SECTIONAL,BARB BARB CROSS-SECTIONAL WIDTH A MEASUREMENT OF THE CROSS-SECTION TAKEN AT RIGHT ANGLES TO THE LENGTH, IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AJUGJ /D/ 04LENGTH,CROSS-SECTIONAL,WIRE WIRE CROSS-SECTIONAL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CROSS-SECTION, IN DISTINCTION FROM WIDTH 2D AND 1B MODE REPLY21AA051AC20 AJUHJ 04WIDTH,CROSS-SECTIONAL,WIRE WIRE CROSS-SECTIONAL WIDTH A MEASUREMENT OF THE CROSS-SECTION TAKEN AT RIGHT ANGLES TO THE LENGTH, IN DISTINCTION FROM THICKNESS 2D AND 1B MODE REPLY21AA051AC20 AJUJL 16STYLE DESIGNATOR,SECTION,TEMPLE TEMPLE SECTION STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE TEMPLE SECTION APPEARANCE. 1L MODE REPLY 0 AJUKL 16STYLE DESIGNATOR,CYLINDER CYLINDER STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CYLINDER. 1L MODE REPLY 0 AJULL 16STYLE,STONE STONE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE STONE. 1L MODE REPLY 0 AJUML 16STYLE,BRICK BRICK STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BRICK. 1L MODE REPLY 0 AJUNL 16QUICK DISCONNECT STYLE,CONNECTION,SUCTION SUCTION CONNECTION QUICK DISCONNECT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SUCTION CONNECTION QUICK DISCONNECT. 1L MODE REPLY 0 AJUPL 16STYLE,RIM RIM STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE RIM. 1L MODE REPLY 0 AJUQL 16STYLE,ADAPTER ADAPTER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ADAPTER. 1L MODE REPLY 0 AJURL 16STYLE DESIGNATOR,CONNECTION,CIRCUIT CIRCUIT CONNECTION STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CIRCUIT CONNECTION. 1L MODE REPLY 0 AJUSD 04OPENING,GAP GAP OPENING INDICATES THE SIZE OF THE GAP OPENING IN REFERENCE TO A 90 DEGREE ANGLE. SELECT REPLY CODE 10AD21 AJUTL 16STYLE DESIGNATOR,LEG LEG STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LEG. 1L MODE REPLY 0 AJUUL 16STYLE DESIGNATOR,LOOP LOOP STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LOOP(S). 1L MODE REPLY 0 AJUVL 16SHAPE STYLE,MESH MESH SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE MESH. 1L MODE REPLY 0 AJUWL 16STYLE,ROLLER ROLLER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ROLLER. 1L MODE REPLY 0 AJUXL 16STYLE,CLIP,MOUNTING MOUNTING CLIP STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE MOUNTING CLIP. 1L MODE REPLY 0 AJUYL /D/ 16STYLE,BASE,ADDITIONAL ADDITIONAL BASE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ADDITIONAL BASE. 1L MODE REPLY 0 AJUZJ 04HEIGHT,FEATURE,ATTACHMENT ATTACHMENT FEATURE HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE TOP TO THE BOTTOM OF THE ATTACHMENT SURFACE. 2D AND 1B MODE REPLY21AA051AC20 AJVAJ 10MAGNITUDE IN OHMS,IMPEDANCE,ZCO ZCO IMPEDANCE MAGNITUDE IN OHMS THE MAGNITUDE PART /Z/ OF THE COMPENSATION IMPEDANCE WITH THE ROTOR OPEN /ZCO/,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 AJVBJ 04ANGLE IN DEG,IMPEDANCE,ZCO ZCO IMPEDANCE ANGLE IN DEG THE ANGLE PART /O/ OF THE COMPENSATOR IMPEDANCE WITH THE ROTOR OPEN /ZCO/,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 AJVCJ 10RESISTANCE IN OHMS,DC,COMPENSATOR COMPENSATOR DC RESISTANCE IN OHMS THE OPPOSITION THAT THE COMPENSATOR OFFERS TO THE FLOW OF DIRECT CURRENT,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 AJVDJ 10RATIO IN PERCENT,TRANSFORMATION,COMPENSATOR COMPENSATOR TRANSFORMATION RATIO IN PERCENT THE RATIO OF THE FUNDAMENTAL COMPONENT OF THE NO-LOAD SECONDARY VOLTAGE TO THE COMPENSATOR VOLTAGE AT MAXIMUM COUPLING,EXPRESSED IN PERCENT. 2D AND 1B MODE REPLY22AG011AC20 AJVEB 10FREQUENCY IN HERTZ,RESONANT,COMPENSATOR COMPENSATOR RESONANT FREQUENCY IN HERTZ THE POINT WHERE THE OUTPUT VOLTAGE OF THE COMPENSATOR IS A MAXIMUM VALUE AND PHASE SHIFT IS MINUS 90 DEGREES,EXPRESSED IN HERTZ. 1B MODE REPLY 0 AJVFJ 04ANGLE IN DEG,SHIFT,PHASE PHASE SHIFT ANGLE IN DEG THE DIFFERENCE BETWEEN THE PHASE TIME OF TWO OR MORE VOLTAGES OR CURRENTS OF THE SAME FREQUENCY,AT THE SAME INSTANT OF TIME,EXPRESSED IN DEGREES. 2D AND 1B MODE REPLY22AG041AC20 AJVGJ 10VOLTAGE IN MILLIVOLTS PER VOLT,NULL,FUNDAMENTAL,MAXIMUM MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT THE MAXIMUM VOLTAGE,WITHOUT HARMONICS,INDUCED IN THE SECONDARY CIRCUIT AT THE NULL ANGLE ROTOR POSITION,EXPRESSED IN MILLIVOLTS PER VOLT. 1D AND 1B MODE REPLY11AC00 AJVHB 10OUTPUT IN MILLIVOLTS PER VOLT,VOLTAGE,MAXIMUM TOTAL NULL MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT THE MAXIMUM VOLTAGE,INCLUDING HARMONICS,INDUCED IN THE SECONDARY CIRCUIT AT THE NULL ANGLE ROTOR POSITION,EXPRESSED IN MILLIVOLTS PER VOLT. 1B MODE REPLY 0 AJVJF T10RANGE IN MINUTES,ANGULAR,INTERAXIS ERROR INTERAXIS ERROR ANGULAR RANGE IN MINUTES THE DEVIATION FROM 90 DEGREES PERPENDICULARITY OF THE SECONDARY WINDING,WHEN EXCITATION IS APPLIED TO ONE OF THE PRIMARY WINDINGS,EXPRESSED IN MINUTES. 1F MODE REPLY 0 AJVKF T10RANGE IN PERCENT,ERROR,FUNCTIONAL,OUTPUT VOLTAGE OUTPUT VOLTAGE FUNCTIONAL ERROR RANGE IN PERCENT THE LIMITS OF PERMISSIBLE DEVIATION OF THE ACTUAL OUTPUT VOLTAGE FORM THE THEORETICAL SINUSOIDAL OUTPUT VOLTAGE DIVIDED BY THE MAXIMUM OUTPUT,EXPRESSED IN PERCENT. 1F MODE REPLY 0 AJVLF T10RANGE IN MINUTES,ANGULAR,ELECTRICAL ERROR ELECTRICAL ERROR ANGULAR RANGE IN MINUTES THE LIMITS OF PERMISSIBLE DEVIATION IN ANGULAR ARC ERROR FROM ELECTRICAL ZERO,EXPRESSED IN MINUTES. 1F MODE REPLY 0 AJVMA 12QUANTITY,TOOTH,SPLINE SPLINE TOOTH QUANTITY THE NUMBER OF INDIVIDUAL TEETH ON THE SPLINED PORTION OF THE SHAFT. 1A MODE REPLY 0 AJVNF T10RANGE IN MINUTES,ANGULAR,RECEIVER ERROR RECEIVER ERROR ANGULAR RANGE IN MINUTES THE LIMITS OF PERMISSIBLE DEVIATION BETWEEN THE POSITION TRANSMITTED AND THE POSITION ASSUMED WHEN THE RECEIVER IS CONNECTED TO A TRANSMITTER OF EQUAL SIZE,EXPRESSED IN MINUTES. 1F MODE REPLY 0 AJVPF T10RANGE IN DEG,LINEAR,MAXOMUM MAXIMUM LINEAR RANGE IN DEG THE RATED EXCURSION OF ANGULAR MEASUREMENT OF THAT PART OF TOTAL ROTATIONAL TRAVEL IN WHICH THE OUTPUT CHARACTERISTIC CHANGES AT A RATE IN DIRECT PROPORTION TO THE ANGULAR PRIMARY TO SECONDARY ORIENTATION CHANGES,EXPRESSED IN DEGREES. 1F MODE REPLY 0 AJVQB 10LINEARITY IN PERCENT LINEARITY IN PERCENT THE VARIANCE,IN THE SPECIFIED OUTPUT CHARACTERISTICS FROM THE THEORETICALLY PERCISE VALUES,THROUGHOUT THE LINEAR OPERATIONAL RANGE,EXPRESSED AS A PERCENTAGE OF DEVIATION FROM THE STRAIGHT LINE RATE OF CHANGE. 1B MODE REPLY 0 AJVRB 10VOLTAGE CHANGE PER DEG IN VOLTS,OUTPUT OUTPUT VOLTAGE CHANGE PER DEG IN VOLTS THE CHANGE IN OUTPUT VOLTAGE FOR A DEGREE OF ANGULAR DISPLACEMENT IN THE LINEAR RANGE /ALSO REFERRED TO AS SENSITIVITY/,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AJVSJ 10TORQUE AT MINUS 55 DEG CELSIUS,FRICTION,ACTUATOR ACTUATOR FRICTION TORQUE AT MINUS 55 DEG CELSIUS THE AMOUNT OF ROTARY FORCE THAT MUST BE APPLIED TO THE ACTUATOR TO CAUSE ROTATION,AT MINUS 55 DEGREES CELSIUS. 2D AND 1B MODE REPLY21AA561AC20 AJVTJ 10TORQUE AT PLUS 25 DEG CELSIUS,FRICTION,ACTUATOR ACTUATOR FRICTION TORQUE AT PLUS 25 DEG CELSIUS THE AMOUNT OF ROTARY FORCE THAT MUST BE APPLIED TO THE ACTUATOR TO CAUSE ROTATION,AT PLUS 25 DEGREES CELSIUS. 2D AND 1B MODE REPLY21AA561AC20 AJVUJ 04WIDTH,EXPOSURE EXPOSURE WIDTH THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE FRONT TO THE BACK OF THE SURFACE THAT WILL REMAIN EXPOSED AFTER THE INSTALLATION OF AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 AJVVJ 10GRADIENT PER ANGULAR DEG,TORQUE TORQUE GRADIENT PER ANGULAR DEG THE AVERAGE TORQUE PER ANGULAR DEGREE DEVELOPED BETWEEN TWO LIKE ITEMS,WHEN ONE ROTOR IS TURNED /OR DISPLACED/ AT 2 DEGREE INTERVALS,BETWEEN A 10 DEGREE COUNTERCLOCKWISE POSITION AND 10 DEGREE CLOCKWISE POSITION. 2D AND 1B MODE REPLY21AA561AC20 AJVWA 12QUANTITY,HOLE,ALIGNMENT ALIGNMENT HOLE QUANTITY THE NUMBER OF HOLES PROVIDED FOR ALIGNING THE ITEM. 1A MODE REPLY 0 AJVXF /D/T10ANGULAR VARIATION DUE TO ROTATION IN MINUTES,SHIFT,PHASE PHASE SHIFT ANGULAR VARIATION DUE TO ROTATION IN MINUTES THE TOTAL VARIATION OF PHASE SHIFT WITH CHANGING ROTOR POSITION,EXPRESSED IN MINUTES. 1F MODE REPLY 0 AJVYF /D/T10ANGULAR VARIATION DUE TO VOLTAGE IN MINUTES,SHIFT,PHASE PHASE SHIFT ANGULAR VARIATION DUE TO VOLTAGE IN MINUTES THE TOTAL VARIATION OF PHASE SHIFT WITH CHANGING INPUT VOLTAGE,EXPRESSED IN MINUTES. 1F MODE REPLY 0 AJVZJ /D/ 10FREQUENCY IN HERTZ,RESONANT,ROTOR ROTOR RESONANT FREQUENCY IN HERTZ THE POINT WHERE THE OUTPUT VOLTAGE OF THE ROTOR IS A MAXIMUM VALUE AND PHASE SHIFT IS MINUS 90 DEGREES,EXPRESSED IN HERTZ. 1D AND 1B MODE REPLY11AC20 AJWAJ /D/ 10FREQUENCY IN HERTZ,CORNER,LOW LOW CORNER FREQUENCY IN HERTZ THE POINT WHERE THE OUTPUT VOLTAGE IS DOWN 3 DECIBELS AND PHASE SHIFT IS PLUS 45 DEGREES,EXPRESSED IN HERTZ. 1D AND 1B MODE REPLY11AC20 AJWBF /D/T10SHIFT WITH VOLTAGE IN ANGULAR MINUTES,ZERO ZERO SHIFT WITH VOLTAGE IN ANGULAR MINUTES THE LIMITS OF PERMISSIBLE DEVIATION OF POSITION OF ZERO WITH VARIATION OF VOLTAGE,EXPRESSED IN ANGULAR MINUTES. 1F MODE REPLY 0 AJWCF /D/T10SHIFT WITH FREQUENCY IN ANGULAR MINUTES,ZERO ZERO SHIFT WITH FREQUENCY IN ANGULAR MINUTES THE LIMITS OF PERMISSIBLE DEVIATION OF POSITION OF ZERO VARIATION OF FREQUENCY,EXPRESSED IN ANGULAR MINUTES. 1F MODE REPLY 0 AJWDB /D/ 10TIME IN SECONDS,SYNCHRONIZING,RECEIVER RECEIVER SYNCHRONIZING TIME IN SECONDS THE PERIOD OF TIME REQUIRED FOR A SYNCHRO RECEIVER OR DIFFERENTIAL RECEIVER TO REACH AND HOLD A SYNCHRONOUS POSITION,EXPRESSED IN SECONDS. 1B MODE REPLY 0 AJWEJ /D/ 10POINT,TEST,SHAFT RADIAL PLAY SHAFT RADIAL PLAY TEST POINT THE MEASUREMENT TAKEN FROM THE BEARING FACE TO THE POINT ON THE SHAFT WHERE THE WEIGHT /LOAD/ IS APPLIED. 2D AND 1B MODE REPLY21AA051AC20 AJWFB /D/ 10WEIGHT IN OZ,DETERMINING,SHAFT RADIAL PLAY SHAFT RADIAL PLAY DETERMINING WEIGHT IN OZ THE FORCE /LOAD/ APPLIED PERPENDICULAR TO THE SHAFT AXIS TO DETERMINE SHAFT RADIAL PLAY,EXPRESSED IN OUNCES. 1B MODE REPLY 0 AJWGJ 10PLAY,RADIAL,MAXIMUM,SHAFT SHAFT MAXIMUM RADIAL PLAY THE MAXIMUM SHAFT DISPLACEMENT PERPENDICULAR TO THE SHAFT AXIS DUE TO REVERSAL OF A SPECIFIED FORCE APPLIED PERPENDICULAR TO THE SHAFT AXIS,AND MEASURED AT A SPECIFIED DISTANCE FROM THE FRONT SURFACE OF THE UNIT. 1D AND 1B MODE REPLY11AA05 AJWHJ 10PLAY,END,SHAFT SHAFT END PLAY THE AXIAL SHAFT DISPLACEMENT DUE TO REVERSAL OF A SPECIFIED AXIAL FORCE,MEASURED AT THE END OF THE SHAFT. 2D AND 1B MODE REPLY21AA051AC20 AJWJB /D/ 10WEIGHT IN OZ,DETERMINING,SHAFT END PLAY SHAFT END PLAY DETERMINING WEIGHT IN OZ THE FORCE /LOAD/ APPLIED PARALLEL TO THE SHAFT AXIS TO DETERMINE SHAFT END PLAY,EXPRESSED IN OUNCES. 1B MODE REPLY 0 AJWKJ 10WEIGHT WEIGHT A RELATIVE MEASURE OF THE MASS OF AN ITEM WITH RESPECT TO ITS DENSITY. 2D AND 1B MODE REPLY22AB161AC20 AJWLD /D/ 19EQUATION,VOLTAGE,VECTOR VECTOR VOLTAGE EQUATION THE METHOD FOR COMPUTING THE OUTPUT VOLTAGE. SELECT REPLY CODE 10AG06 AJWMD /D/ 05DIRECTION,ROTATION,POSITIVE,ROTOR ROTOR POSITIVE ROTATION DIRECTION THE PATH OF THE ROTOR,WHEN MOVED FROM SYNCHRO OR RESOLVER ZERO,EXPRESSED IN RELATION TO A CLOCKFACE. SELECT REPLY CODE 10AC84 AJWNJ /D/ 10DISPLACEMENT FOR SYNCHRONIZING TIME IN DEG,ANGULAR,ROTOR ROTOR ANGULAR DISPLACEMENT FOR SYNCHRONIZING TIME IN DEG THE ANGULAR DISPLACEMENT OF THE ROTOR FROM WHICH THE SYNCHRONIZING TIME WAS DETERMINED,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 AJWPH 03DESIGNATOR AND SCHEMATIC POSITION,TERMINAL TERMINAL DESIGNATOR AND SCHEMATIC POSITION A DESIGNATION IDENTIFYING THE ELECTRICAL CONNECTION FACILITY PROVIDED FOR EACH TERMINATION OF THE ITEM,AND ITS LOCATION ON THE SCHEMATIC DIAGRAM. 2D MODE REPLY 22AG072AG12 AJWQJ 04LENGTH,PILOT PILOT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A PILOT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AJWRJ 04LENGTH,SHOULDER SHOULDER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AJWSJ 04DIAMETER,OUTSIDE,GEAR GEAR OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A GEAR,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJWTJ 04THICKNESS,GEAR GEAR THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AJWUJ /D/ 04SECOND THICKNESS,ACCOMMODATED,MATERIAL MATERIAL ACCOMMODATED SECOND THICKNESS THE THICKNESS OF THE MATERIAL TO BE ACCOMODATED. 2D AND 1B MODE REPLY21AA051AC20 AJWVJ 04DIAMETER,FLANGE,FIRST,AFT OF AFT OF FIRST FLANGE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJWWJ 04DIAMETER,FLANGE,SECOND,AFT OF AFT OF SECOND FLANGE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AJWXJ 04DISTANCE,MOUNTING SURFACE TO TERMINAL END MOUNTING SURFACE TO TERMINAL END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AJWYJ 04DISTANCE,SECOND SHOULDER FACE TO REAR FLANGE SECOND SHOULDER FACE TO REAR FLANGE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AJWZJ 04DISTANCE,HOLE CENTER TO SHAFT END HOLE CENTER TO SHAFT END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AJXAA 10PITCH,DIAMETRAL,SPLINE TOOTH SPLINE TOOTH DIAMETRAL PITCH THE NUMBER OF TEETH THE SPLINED SHAFT HAS PER INCH OF PITCH DIAMETER. 1A MODE REPLY 0 AJXBJ 10RUNOUT,MAXIMUM,SHAFT SHAFT MAXIMUM RUNOUT THE ECCENTRICITY OF THE SHAFT DIAMETER WITH RESPECT TO THE ROTATIONAL AXIS OF THE SHAFT,MEASURED AT A SPECIFIED DISTANCE FROM THE END OF THE SHAFT,WHEN THE BODY OF THE ITEM IS HELD FIXED AND THE SHAFT IS ROTATED. 1D AND 1B MODE REPLY11AA05 AJXCB /D/ 10RESISTANCE IN OHMS,MAXIMUM,ROTOR BRUSH CONTACT ROTOR BRUSH CONTACT MAXIMUM RESISTANCE IN OHMS THE CHANGE IN RESISTANCE BETWEEN THE TERMINALS AS THE ROTOR IS TURNED THROUGH A COMPLETE REVOLUTION,EXPRESSED IN OHMS. 1B MODE REPLY 0 AJXDB /D/ 10DISTORTION IN PERCENT,HARMONIC,MAXIMUM MAXIMUM HARMONIC DISTORTION IN PERCENT A MEASURE OF THE DIFFERENCE BETWEEN THE SHAPE OF THE OUTPUT VOLTAGE WAVE AND THE SHAPE OF THE INPUT VOLTAGE WAVE,EXPRESSED IN PERCENT. 1B MODE REPLY 0 AJXEA 03DESIGNATOR,SIZE SIZE DESIGNATOR A DESIGNATION INDICATING THE SIZE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1A MODE REPLY 0 AJXFL 16STYLE,ROPE ROPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ROPE. 1L MODE REPLY 0 AJXGA /D/ 16STYLE,STRAND STRAND STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE STRAND. 1A MODE REPLY 0 AJXHD 11METHOD,LAY LAY METHOD THE MEANS IN WHICH FILAMENTS ARE LAID INTO STRANDS OR STRANDS INTO ROPE OR LIKE ITEMS. SELECT REPLY CODE 10AG08 AJXJD /D/ 09MATERIAL,CORE CORE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CORE IS FABRICATED. PLEASE USE MRC CZLR IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AJXKD /D/ 19FORM,WIRE,PREFABRICATION STRAND PREFABRICATION STRAND WIRE FORM THE FORM OF WIRE FURNISHED PRIOR TO STRAND FABRICATION. SELECT REPLY CODE 10AC41 AJXLD /D/ 09MATERIAL,COVERING,STRAND STRAND COVERING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE STRAND COVERING IS FABRICATED. SELECT REPLY CODE 10AD09 AJXMJ 04DIAMETER,ROPE ROPE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A ROPE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJXNJ 10STRENGTH,BREAKING BREAKING STRENGTH THE MEASURED LOAD REQUIRED TO BREAK THE ITEM IN TENSION. 2D AND 1B MODE REPLY22AB161AC20 AJXPD /D/ 18TYPE,GUY GUY TYPE INDICATES THE TYPE OF GUY UTILIZED. SELECT REPLY CODE 10AF37 AJXQA /D/ 16STYLE,CHAIN CHAIN STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CHAIN. 1A MODE REPLY 0 AJXRJ /D/ 04DIAMETER,STRAND STRAND DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A STRAND,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJXSJ 04DIAMETER,BEAD BEAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BEAD,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJXTL 16STYLE,LINK LINK STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LINK. 1L MODE REPLY 0 AJXUJ /D/ 04DEPTH,EXPOSURE EXPOSURE DEPTH THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE FRONT TO THE SIDE OF THE SURFACE THAT WILL REMAIN EXPOSED AFTER THE INSTALLATION OF AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 AJXVD /D/ 07LINK,DIE-LOCK DIE-LOCK LINK AN INDICATION OF WHETHER OR NOT A DIE-LOCK LINK IS INCLUDED. SELECT REPLY CODE 10AA49 AJXWD /D/ 07FEATURE,HINGE HINGE FEATURE AN INDICATION OF WHETHER OR NOT A HINGE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AJXXJ /D/A12QUANTITY PER UNIT OF MEASURE,BEAD BEAD QUANTITY PER UNIT OF MEASURE THE NUMBER OF BEADS COMPRISING A SPECIFIC UNIT OF MEASURE. 1D AND 1A MODE REPLY11AB39 AJXYD 18TYPE,CHAIN CHAIN TYPE INDICATES THE TYPE OF CHAIN BY THE FABRICATED SHAPE AND/OR STYLE OF LINK. SELECT REPLY CODE 10AG09 AJXZD 18TYPE,END,ASSEMBLY ASSEMBLY END TYPE INDICATES THE TYPE OF END TERMINATION(S) INCLUDED. SELECT REPLY CODE 10AG10 AJYAD 18TYPE,ATTACHMENT,INTERMEDIATE INTERMEDIATE ATTACHMENT TYPE INDICATES THE TYPE OF INTERMEDIATE ATTACHMENT(S) PROVIDED. SELECT REPLY CODE 10AC06 AJYBJ 04DISTANCE,FIRST END TO FIRST FIXED INTERMEDIATE ATTACHMENT FIRST END TO FIRST FIXED INTERMEDIATE ATTACHMENT DISTANCE THE DISTANCE WHICH LOCATES THE FIXED ATTACHMENT WITH RELATION TO THE ASSEMBLED END. 2D AND 1B MODE REPLY21AA051AC20 AJYCD /D/ 11METHOD,RETENTION,LOOP LOOP RETENTION METHOD THE MEANS USED TO RETAIN A FORMED LOOP ON THE END OF THE ITEM. SELECT REPLY CODE 10AB89 AJYDA 12QUANTITY,THIMBLE THIMBLE QUANTITY THE NUMBER OF THIMBLES INCLUDED. 1A MODE REPLY 0 AJYEL 16STYLE,THIMBLE THIMBLE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE THIMBLE. 1L MODE REPLY 0 AJYFJ 04LENGTH,INSIDE,LOOP LOOP INSIDE LENGTH THE LONGEST DISTANCE MEASURED WHEN THE LOOP/S/ LAY NATURAL AND THE LENGTH IS APPROXIMATELY TWICE THE WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AJYGJ 04WIDTH,INSIDE,LOOP LOOP INSIDE WIDTH THE SHORTER DISTANCE MEASURED WHEN THE LOOP/S/ LAY NATURAL AND THE LENGTH IS APPROXIMATELY TWICE THE WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AJYHD 11METHOD,CONDITIONING,ROPE END ROPE END CONDITIONING METHOD THE MEANS USED TO PREVENT UNRAVELING OF THE ROPE ENDS. SELECT REPLY CODE 10AA62 AJYJA /D/ 19NUMBER,MODEL,PACKAGE PACKAGE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE PACKAGE. PLEASE USE MRC AMWN IN PLACE OF THIS DISCONTINUED MRC. 1A MODE REPLY 0 AJYKH /D/ 09MATERIAL AND LOCATION,ASSEMBLY ASSEMBLY MATERIAL AND LOCATION THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH AN ASSEMBLY IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT,AND A DESIGNATION OF THAT PORTION TO WHICH A SPECIFIC MATERIAL IS APPLICABLE. 2D MODE REPLY 26AD092AE46 AJYLH /D/ 17SURFACE TREATMENT AND LOCATION,ASSEMBLY ASSEMBLY SURFACE TREATMENT AND LOCATION THE PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROMECHANICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE ASSEMBLY AND A DESIGNATION OF THAT PORTION TO WHICH THE SPECIFIC SURFACE TREATMENT IS APPLIED. 2D MODE REPLY 26AD092AE46 AJYMD 13SCREW THREAD FORM DESIGNATOR SCREW THREAD FORM DESIGNATOR A DESIGNATION DISTINGUISHING ONE SCREW THREAD FROM ANOTHER ACCORDING TO THE PARTICULAR FORM DEVELOPED,USUALLY DENOTED BY DESIGN DIFFERENCES IN THE BASIC PROFILE. SELECT REPLY CODE 10AG11 AJYNJ 04SCREW THREAD DIAMETER SCREW THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COAXIAL CYLINDER WHICH WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD. 2D AND 1B MODE REPLY21AA051AC20 AJYPD 13SCREW THREAD SERIES DESIGNATOR SCREW THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 AJYQB 13SCREW THREAD QUANTITY PER INCH SCREW THREAD QUANTITY PER INCH THE NUMBER OF SCREW THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS,INCLUDING INCOMPLETE THREADS. 1B MODE REPLY 0 AJYRJ 04SCREW THREAD LENGTH SCREW THREAD LENGTH A MEASUREMENT OF THE EXTENT OF SCREW THREADS,INCLUDING INCOMPLETE SCREW THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL THREAD AXIS. 2D AND 1B MODE REPLY21AA051AC20 AJYSD /D/ 13SCREW THREAD FORM DESIGNATOR,HOLE HOLE SCREW THREAD FORM DESIGNATOR A DESIGNATION DISTINGUISHING ONE HOLE SCREW THREAD FROM ANOTHER ACCORDING TO THE PARTICULAR FORM DEVELOPED,USUALLY DENOTED BY DESIGN DIFFERENCES IN THE BASE PROFILE. SELECT REPLY CODE 10AG11 AJYTD 13SCREW THREAD SERIES DESIGNATOR,HOLE HOLE SCREW THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF HOLE SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 AJYUL 16STYLE,ARBOR HOLE ARBOR HOLE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ARBOR HOLE. 1L MODE REPLY 0 AJYVJ /D/ 13SCREW THREAD DIAMETER,HOLE HOLE SCREW THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOLE SCREW THREAD,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJYWB /D/ 13SCREW THREAD QUANTITY PER INCH,HOLE HOLE SCREW THREAD QUANTITY PER INCH A MEASUREMENT OF THE NUMBER OF SCREW THREADS ON THE HOLE PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1B MODE REPLY 0 AJYXD /D/ 13SCREW THREAD FORM DESIGNATOR,SHAFT SHAFT SCREW THREAD FORM DESIGNATOR A DESIGNATION DISTINGUISHING ONE SHAFT SCREW THREAD FROM ANOTHER ACCORDING TO THE PARTICULAR FORM DEVELOPED USUALLY DENOTED BY DESIGN DIFFERENCES IN THE BASIC PROFILE. SELECT REPLY CODE 10AG11 AJYYD 13THREAD SERIES DESIGNATOR,SHAFT SHAFT THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF SHAFT THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 AJYZJ /D/ 13SCREW THREAD DIAMETER,SHAFT SHAFT SCREW THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COAXIAL CYLINDER,WHICH WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AJZAB /D/ 13SCREW THREAD QUANTITY PER INCH,SHAFT SHAFT SCREW THREAD QUANTITY PER INCH A MEASUREMENT OF THE NUMBER OF SCREW THREADS ON THE SHAFT PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1B MODE REPLY 0 AJZBJ /D/ 10WEIGHT,MATERIAL,PRECIOUS PRECIOUS MATERIAL WEIGHT THE SPECIFIC WEIGHT OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM. 1D AND 1B MODE REPLY11AG14 AJZCD 18TYPE,SWITCH,PRESSURE PRESSURE SWITCH TYPE THE GENERAL CLASSIFICATION OF A PRESSURE SWITCH BASED ON THE REFERENCE METHOD USED TO MEASURE THE SENSED PRESSURE. SELECT REPLY CODE 10AG15 AJZDD /D/ 19PLANE,ACTUATING ACTUATING PLANE THE PLANE IN WHICH THE ITEM IS DESIGNED TO OPERATE WHEN ACTUATED BY A STIMULUS. SELECT REPLY CODE 10AC60 AJZED 02DESIGN,BASIC,SWITCH CONTACT SWITCH CONTACT BASIC DESIGN THE GENERAL CONFIGURATION OF THE CONTACTS OF A SWITCH THAT DESCRIBES ITS BASIC SWITCHING STRUCTURE. SELECT REPLY CODE 10AD79 AJZFJ /D/A19ARRANGEMENT,FORM,PILE-UP CONTACT PILE-UP CONTACT FORM ARRANGEMENT THE BASIC CONTACT FORMS IN THE ORDER OF ASSEMBLAGE THAT COLLECTIVELY DESCRIBE THE SWITCHING STRUCTURE OF A PILE-UP CONTACT GROUP. 1D AND 1A MODE REPLY12AG16 AJZGJ /D/A19ARRANGEMENT,CONTACT,NONPILE-UP NONPILE-UP CONTACT ARRANGEMENT THE DESIGNATION THAT IDENTIFIES THE ELECTRICAL CONFIGURATION OF A NONPILE-UP CONTACT GROUP INCLUDING THE NUMBER OF SWITCHING POLES OR FORMS. 2D AND 1A MODE REPLY22AG282AG16 AJZHH /D/ 19STIMULUS REQUIRED,ACTION,CONTACT CONTACT ACTION STIMULUS REQUIRED AN INDICATION OF WHETHER THE INITIAL ACTION OF THE CONTACTS OCCURS AS THE RESULT OF AN INCREASE OR DECREASE IN STIMULUS /PRESSURE,TEMPERATURE,FORCE,VELOCITY,AND THE LIKE/. 2D MODE REPLY 22AG162AG17 AJZJH /D/ 19POSITION,CALIBRATING,ACTUATOR ARM ACTUATOR ARM CALIBRATING POSITION THE POSITION OF THE ACTUATING ARM /VANE/ AT WHICH THE PERFORMANCE RATING APPLIES. 2D MODE REPLY 22AG162AG19 AJZKH /D/ 19ADJUSTABILITY,POINT,CONTACT ACTUATION CONTACT ACTUATION POINT ADJUSTABILITY AN INDICATION OF WHETHER THE POINT AT WHICH THE CONTACTS ACTUATE IS ADJUSTABLE. 2D MODE REPLY 22AG161AC06 AJZLH /D/ 18TYPE,ADJUSTER,MANUAL,CONTACT ACTUATION POINT CONTACT ACTUATION POINT MANUAL ADJUSTER TYPE INDICATES THE TYPE OF DEVICE PROVIDED FOR MANUAL ADJUSTMENT OF THE CONTACTS ACTUATION POINT. 2D MODE REPLY 22AG162AG18 AJZMH /D/ 08LOCATION,ADJUSTER,MANUAL,CONTACT ACTUATION POINT CONTACT ACTUATION POINT MANUAL ADJUSTER LOCATION INDICATES THE LOCATION OF THE CONTACTS MANUAL POINT ADJUSTER. 2D MODE REPLY 22AG163AJ91 AJZNJ /D/T10RANGE,ADJUSTMENT,CONTACT ACTUATION POINT CONTACT ACTUATION POINT ADJUSTMENT RANGE THE MINIMUM AND MAXIMUM LIMITS TO WHICH THE CONTACTS ACTUATION POINT MAY BE ADJUSTED. 2D AND 1F MODE REPLY22AG202AG16 AJZPJ /D/ 10STIMULUS RATING,POINT,CONTACT ACTUATION CONTACT ACTUATION POINT STIMULUS RATING THE VALUE OF THE STIMULUS AT WHICH THE CONTACTS ACTUATE. 3D AND 1B MODE REPLY32AG201AC202AG16 AJZQH /D/ 19ADJUSTABILITY,POINT,CONTACT DEACTUATION CONTACT DEACTUATION POINT ADJUSTABILITY AN INDICATION OF WHETHER THE POINT AT WHICH THE CONTACTS DEACTUATE IS ADJUSTABLE. 2D MODE REPLY 22AG161AC06 AJZRH /D/ 18TYPE,ADJUSTER,MANUAL,CONTACT DEACTUATION POINT CONTACT DEACTUATION POINT MANUAL ADJUSTER TYPE INDICATES THE TYPE OF DEVICE PROVIDED FOR MANUAL ADJUSTMENT OF THE CONTACTS DEACTUATION POINT. 2D MODE REPLY 22AG162AG18 AJZSH /D/ 08LOCATION,ADJUSTER,MANUAL,CONTACT DEACTUATION POINT CONTACT DEACTUATION POINT MANUAL ADJUSTER LOCATION INDICATES THE LOCATION OF THE CONTACTS MANUAL DEACTUATION POINT ADJUSTER. 2D MODE REPLY 22AG163AJ91 AJZTJ /D/T10RANGE,ADJUSTMENT,CONTACT DEACTUATION POINT CONTACT DEACTUATION POINT ADJUSTMENT RANGE THE MINIMUM AND MAXIMUM LIMITS TO WHICH THE CONTACTS DEACTUATION POINT MAY BE ADJUSTED. 2D AND 1F MODE REPLY22AG202AG16 AJZUL 16STYLE,FIRST LEG FIRST LEG STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FIRST LEG. 1L MODE REPLY 0 AJZVJ /D/ 10STIMULUS RATING,POINT,CONTACT DEACTUATION CONTACT DEACTUATION POINT STIMULUS RATING THE VALUE OF THE STIMULUS AT WHICH THE CONTACTS DEACTUATE. 3D AND 1B MODE REPLY32AG201AC202AG16 AJZWH /D/ 19ADJUSTABILITY,DIFFERENTIAL,CONTACT ACTUATING CONTACT ACTUATING DIFFERENTIAL ADJUSTABILITY AN INDICATION OF WHETHER THE DIFFERENCE BETWEEN THE POINTS AT WHICH THE CONTACTS ACTUATE AND DEACTUATE IS ADJUSTABLE. 2D MODE REPLY 22AG161AC06 AJZXH /D/ 18TYPE,ADJUSTER,MANUAL,CONTACT ACTUATING DIFFERENTIAL CONTACT ACTUATING DIFFERENTIAL MANUAL ADJUSTER TYPE INDICATES THE TYPE OF DEVICE PROVIDED FOR MANUAL ADJUSTMENT OF THE CONTACTS ACTUATING DIFFERENTIAL. 2D MODE REPLY 22AG162AG18 AJZYH /D/ 08LOCATION,ADJUSTER,MANUAL,CONTACT ACTUATING DIFFERENTIAL CONTACT ACTUATING DIFFERENTIAL MANUAL ADJUSTER LOCATION INDICATES THE LOCATION OF THE CONTACTS ACTUATING DIFFERENTIAL ADJUSTER. 2D MODE REPLY 22AG163AJ91 AJZZJ /D/T10RANGE,ADJUSTMENT,CONTACT ACTUATING DIFFERENTIAL CONTACT ACTUATING DIFFERENTIAL ADJUSTMENT RANGE THE MINIMUM AND MAXIMUM LIMITS TO WHICH THE CONTACTS ACTUATING DIFFERENTIAL MAY BE ADJUSTED. 2D AND 1F MODE REPLY22AG202AG16 AKAAJ /D/ 10STIMULUS RATING,DIFFERENTIAL,CONTACT ACTUATING CONTACT ACTUATING DIFFERENTIAL STIMULUS RATING THE DIFFERENCE IN THE STIMULUS REQUIRED TO ACTUATE AND DEACTUATE THE CONTACTS. 3D AND 1B MODE REPLY32AG201AC202AG16 AKABJ /D/ 10VOLTAGE RATING IN VOLTS,CONTACT CONTACT VOLTAGE RATING IN VOLTS THE VOLTAGE FOR WHICH THE CONTACTS ARE RATED AT SEA LEVEL OR AT A SPECIFIED ALTITUDE,EXPRESSED IN VOLTS. 4D AND 1B MODE REPLY41AB621AD862AD882AG16 AKACJ /D/ 10CURRENT RATING,LOAD,CONTACT CONTACT LOAD CURRENT RATING THE AMOUNT OF CURRENT THAT THE CONTACTS ARE RATED TO MAKE OR BREAK WITH A SPECIFIED LOAD. 6D AND 1B MODE REPLY61AC301AB621AD921AD862AD882AG16 AKADJ /D/ 10TIME IN MILLISECONDS,RESPONSE,ACTUATION ACTUATION RESPONSE TIME IN MILLISECONDS THE INTERVAL OF TIME THAT EXISTS BETWEEN THE TIME THE SENSING ELEMENT REACTS TO STIMULUS CHANGE AND THE TIME THE CONTACTS ACTUATE,EXPRESSED IN MILLISECONDS. 1D AND 1B MODE REPLY12AG16 AKAEJ 10ALTITUDE RATING,OPERATING,MAXIMUM MAXIMUM OPERATING ALTITUDE RATING THE MAXIMUM ALTITUDE AT WHICH THE ITEM IS RATED TO FUNCTION. 1D AND 1B MODE REPLY11AA05 AKAFD 13THREAD DIRECTION,SHAFT SHAFT THREAD DIRECTION THE DIRECTION OF THE SHAFT THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 AKAGD 13THREAD DIRECTION,HOLE HOLE THREAD DIRECTION THE DIRECTION OF THE HOLE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 AKAHJ /D/T13THREAD PITCH DIAMETERS,HOLE HOLE THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 AKAJJ /D/T13THREAD PITCH DIAMETERS,SHAFT SHAFT THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM SHAFT PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 AKAKJ /D/ 13SCREW THREAD LENGTH,HOLE HOLE SCREW THREAD LENGTH A MEASUREMENT OF THE EXTENT OF HOLE SCREW THREADS,INCLUDING INCOMPLETE SCREW THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL THREAD AXIS. 2D AND 1B MODE REPLY21AA051AC20 AKALJ 04SCREW THREAD LENGTH,SHAFT SHAFT SCREW THREAD LENGTH A MEASUREMENT OF THE EXTENT OF SHAFT SCREW THREADS,INCLUDING INCOMPLETE SCREW THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL THREAD AXIS. 2D AND 1B MODE REPLY21AA051AC20 AKAMA /D/ 13THREAD CLASS,HOLE HOLE THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE,AND AN EXTERNAL OR INTERNAL HOLE THREAD. 1A MODE REPLY 0 AKANA 13THREAD CLASS,SHAFT SHAFT THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PTICH DIAMETER TOLERANCE,AND AN EXTERNAL OR INTERNAL SHAFT THREAD. 1A MODE REPLY 0 AKAPJ /D/ 10PRESSURE,PROOF PROOF PRESSURE THE MAXIMUM PRESSURE THAT AN ITEM WILL WITHSTAND WITHOUT RESULTING IN ANY PERMANENT CHANGES IN ITS STRUCTURAL,MECHANICAL,OR ELECTRICAL CHARACTERISTICS. PLEASE USE MRC CQJB IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1B MODE REPLY11AB18 AKAQD /D/ 13SCREW THREAD LOCATION,HOLE HOLE SCREW THREAD LOCATION INDICATES WHETHER THE HOLE SCREW THREAD IS LOCATED EXTERNALLY OR INTERNALLY. SELECT REPLY CODE 10AE46 AKARD /D/ 13SCREW THREAD LOCATION,SHAFT SHAFT SCREW THREAD LOCATION INDICATES WHETHER THE SHAFT SCREW THREAD IS LOCATED EXTERNALLY OR INTERNALLY. SELECT REPLY CODE 10AE46 AKASD /D/ 07FEATURE,LOCKING,ADJUSTMENT ADJUSTMENT LOCKING FEATURE AN INDICATION OF WHETHER OR NOT AN ADJUSTMENT LOCKING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AKATA /D/ 12QUANTITY,CONNECTOR,PRESSURE PRESSURE CONNECTOR QUANTITY THE NUMBER OF CONNECTORS PROVIDED IN THE ITEM FOR CONNECTION TO THE PRESSURE SOURCE. 1A MODE REPLY 0 AKAUL 16STYLE,ARRANGEMENT,FIRST LEG HOLE FIRST LEG HOLE ARRANGEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE FIRST LEG HOLES. 1L MODE REPLY 0 AKAVH /D/ 11METHOD,CONNECTION,PRESSURE PRESSURE CONNECTION METHOD THE MEANS PROVIDED FOR CONNECTING THE ITEM TO THE PRESSURE SOURCE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 2D MODE REPLY 22AG232AG22 AKAWH /D/ 19CONNECTION PER CONTACT GROUP,PRESSURE PRESSURE CONNECTION PER CONTACT GROUP THE CONTACT GROUP THAT IS ACTUATED BY THE PRESSURE INPUT AT THE PRESSURE CONNECTION. 2D MODE REPLY 22AG232AG16 AKAXJ /D/ 16STYLE,CONNECTOR,PRESSURE PRESSURE CONNECTOR STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF A PRESSURE CONNECTOR. 1D AND 1B MODE REPLY12AG23 AKAYJ /D/ 04LENGTH,CONNECTOR,PRESSURE PRESSURE CONNECTOR LENGTH THE LENGTH OF A PRESSURE CONNECTOR MEASURED FROM THE SURFACE FROM WHICH IT EXTENDS TO ITS EXTREMITY. 2D AND 1B MODE REPLY21AA051AC20 AKAZJ /D/ 04DIAMETER,OUTSIDE,PRESSURE CONNECTOR PRESSURE CONNECTOR OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PRESSURE CONNECTOR,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKBAJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CONNECTOR,PRESSURE PRESSURE CONNECTOR THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED PRESSURE CONNECTOR. 2D AND 1A MODE REPLY22AG232AH06 AKBBJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CONNECTOR,TUBING END TUBING END CONNECTOR THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE CONNECTOR PROVIDED FOR TUBING END CONNECTION. 2D AND 1A MODE REPLY22AH062AG23 AKBCJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CONNECTOR,CAPILLARY TUBE END CAPILLARY TUBE END CONNECTOR THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED CAPILLARY TUBE END CONNECTOR. 1D AND 1A MODE REPLY12AH06 AKBDA /D/ 13THREAD CLASS,CONNECTOR,CAPILLARY TUBE END CAPILLARY TUBE END CONNECTOR THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE,AND AN EXTERNAL OR INTERNAL CAPILLARY TUBE END CONNECTOR THREAD. 1A MODE REPLY 0 AKBED /D/ 13THREAD DIRECTION,CONNECTOR,CAPILLARY TUBE END CAPILLARY TUBE END CONNECTOR THREAD DIRECTION THE DIRECTION OF THE THREADS OF A CAPILLARY TUBE END CONNECTION WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 AKBFJ /D/ 13THREAD CLASS,CONNECTOR,PRESSURE PRESSURE CONNECTOR THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE,AND AN EXTERNAL OR INTERNAL PRESSURE CONNECTOR THREAD. 1D AND 1B MODE REPLY12AG23 AKBGJ /D/ 13THREAD LENGTH,CONNECTOR,CAPILLARY TUBE END CAPILLARY TUBE END CONNECTOR THREAD LENGTH A MEASUREMENT OF THE EXTENT OF SCREW THREADS OF A CAPILLARY TUBE END CONNECTOR,INCLUDING INCOMPLETE SCREW THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL THREAD AXIS. 2D AND 1B MODE REPLY21AA051AC20 AKBHH /D/ 13THREAD DIRECTION,CONNECTOR,PRESSURE PRESSURE CONNECTOR THREAD DIRECTION THE DIRECTION OF THE THREADS OF A PRESSURE CONNECTOR WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. 2D MODE REPLY 22AG233AA38 AKBJJ /D/ 13THREAD LENGTH,CONNECTOR,PRESSURE PRESSURE CONNECTOR THREAD LENGTH A MEASUREMENT OF THE EXTENT OF SCREW THREADS OF A PRESSURE CONNECTOR,INCLUDING INCOMPLETE SCREW THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL THREAD AXIS. 3D AND 1B MODE REPLY31AA051AC202AG23 AKBKJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,FACILITY,MOUNTING MOUNTING FACILITY THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED MOUNTING FACILITY. 1D AND 1A MODE REPLY12AH06 AKBLJ /D/A16STYLE,CONNECTOR,TUBING END TUBING END CONNECTOR STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CONNECTOR PROVIDED FOR TUBING END CONNECTION. 1D AND 1A MODE REPLY12AG23 AKBMA 13THREAD CLASS,FACILITY,MOUNTING MOUNTING FACILITY THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE,AND AN EXTERNAL OR INTERNAL THREADED MOUNTING FACILITY. 1A MODE REPLY 0 AKBND 13THREAD DIRECTION,FACILITY,MOUNTING MOUNTING FACILITY THREAD DIRECTION THE DIRECTION OF THE THREADS OF A MOUNTING FACILITY WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 AKBPJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,PORT,ELECTRICAL ACCESS ELECTRICAL ACCESS PORT THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED ELECTRICAL ACCESS PORT. 1D AND 1A MODE REPLY12AH06 AKBQA /D/ 13THREAD CLASS,PORT,ELECTRICAL ACCESS ELECTRICAL ACCESS PORT THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE,AND AN EXTERNAL OR INTERNAL THREADED ELECTRICAL ACCESS PORT. 1A MODE REPLY 0 AKBRD /D/ 13THREAD DIRECTION,PORT,ELECTRICAL ACCESS ELECTRICAL ACCESS PORT THREAD DIRECTION THE DIRECTION OF THE THREADS OF AN ELECTRICAL ACCESS PORT WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 AKBSJ /D/A13THREAD CLASS,CONNECTOR,TUBING END TUBING END CONNECTOR THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE,AND AN EXTERNAL OR INTERNAL THREADED CONNECTOR PROVIDED FOR TUBING END CONNECTION. 1D AND 1A MODE REPLY12AG23 AKBTJ /D/ 13THREAD LENGTH,PORT,ELECTRICAL ACCESS ELECTRICAL ACCESS PORT THREAD LENGTH A MEASUREMENT OF THE EXTENT OF SCREW THREADS OF AN ELECTRICAL ACCESS PORT,INCLUDING INCOMPLETE SCREW THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL THREAD AXIS. 2D AND 1B MODE REPLY21AA051AC20 AKBUL 16STYLE,SECOND LEG SECOND LEG STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SECOND LEG. 1L MODE REPLY 0 AKBVH /D/ 13THREAD DIRECTION,CONNECTOR,TUBING END TUBING END CONNECTOR THREAD DIRECTION THE DIRECTION OF THE THREADS OF A TUBING END CONNECTOR WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 2D MODE REPLY 22AG233AA38 AKBWJ /D/ 13THREAD LENGTH,CONNECTOR,TUBING END TUBING END CONNECTOR THREAD LENGTH A MEASUREMENT OF THE EXTENT OF SCREW THREADS OF A TUBING END CONNECTOR,INCLUDING INCOMPLETE SCREW THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL THREAD AXIS. 3D AND 1B MODE REPLY31AA051AC202AG23 AKBXJ 04THREAD LENGTH,FACILITY,MOUNTING MOUNTING FACILITY THREAD LENGTH A MEASUREMENT OF THE EXTENT OF THREADS ON A MOUNTING FACILITY,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS. 2D AND 1B MODE REPLY21AA051AC20 AKBYD 18TYPE,ELEMENT,SENSING,TEMP TEMP SENSING ELEMENT TYPE INDICATES THE TYPE OF SENSOR OR TRANSDUCER USED IN THE ITEM TO CONVERT TEMPERATURE CHANGES TO SWITCH ACTUATING FORCE. SELECT REPLY CODE 10AG24 AKBZD /D/ 18TYPE,ANTICIPATOR,TEMP TEMP ANTICIPATOR TYPE INDICATES THE TYPE OF DEVICE INCLUDED IN THE ITEM TO PROVIDE QUICK RESPONSE TO CHANGES IN TEMPERATURE. SELECT REPLY CODE 10AD49 AKCAJ /D/ 04DIAMETER,OUTSIDE,CAPILLARY TUBE CAPILLARY TUBE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CAPILLARY TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKCBD /D/ 07CONNECTOR,SEAL,CAPILLARY TUBE END CAPILLARY TUBE END SEAL CONNECTOR AN INDICATION OF WHETHER OR NOT A CONNECTOR IS INCLUDED AT THE END OF THE CAPILLARY TUBE FOR SEALED CONNECTION. SELECT REPLY CODE 10AA49 AKCCJ /D/ 04LENGTH,TUBING TUBING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TUBING,IN DISTINCTION FROM WIDTH. 3D AND 1B MODE REPLY31AA051AC202AG23 AKCDJ /D/ 04DIAMETER,OUTSIDE,TUBING TUBING OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CNETER OF THE TUBING,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 3D AND 1B MODE REPLY31AA051AC202AG23 AKCEH /D/ 07CONNECTOR,SEAL,TUBING END TUBING END SEAL CONNECTOR AN INDICATION OF WHETHER OR NOT A CONNECTOR IS INCLUDED AT THE END OF THE TUBING FOR SEALED CONNECTION. 2D MODE REPLY 22AG231AA49 AKCFJ /D/ 04ANGLE IN DEG,SEAT,PRESSURE CONNECTOR PRESSURE CONNECTOR SEAT ANGLE IN DEG THE ANGLE OF THE END SURFACE OF THE PRESSURE CONNECTOR UPON WHICH THE MATING SURFACE SEATS,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY12AG23 AKCGJ /D/ 04RADIUS,SEAT,PRESSURE CONNECTOR PRESSURE CONNECTOR SEAT RADIUS THE RADIUS OF THE END SURFACE OF THE PRESSURE CONNECTOR UPON WHICH THE MATING SURFACE SEATS. 3D AND 1B MODE REPLY31AA051AC202AG23 AKCHJ /D/ 04ANGLE IN DEG,SEAT,TUBING END CONNECTOR TUBING END CONNECTOR SEAT ANGLE IN DEG THE ANGLE OF THE END SURFACE OF THE TUBING END CONNECTOR UPON WHICH THE MATING SURFACE SEATS,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY12AG23 AKCJJ /D/ 04RADIUS,SEAT,TUBING END CONNECTOR TUBING END CONNECTOR SEAT RADIUS THE RADIUS OF THE END SURFACE OF THE TUBING END CONNECTOR UPON WHICH THE MATING SURFACE SEATS. 3D AND 1B MODE REPLY31AA051AC202AG23 AKCKL /D/ 16STYLE,CONNECTOR,CAPILLARY TUBE END CAPILLARY TUBE END CONNECTOR STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION OF THE CONNECTOR PROVIDED FOR SEALED CONNECTION OF THE END OF THE CAPILLARY TUBE. 1L MODE REPLY 0 AKCLB /D/ 04ANGLE IN DEG,SEAT,CAPILLARY TUBE END CONNECTOR CAPILLARY TUBE END CONNECTOR SEAT ANGLE IN DEG THE ANGLE OF THE END SURFACE OF A CAPILLARY TUBE END CONNECTOR UPON WHICH THE MATING SURFACE SEATS,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AKCMJ /D/ 04RADIUS,SEAT,CAPILLARY TUBE END CONNECTOR CAPILLARY TUBE END CONNECTOR SEAT RADIUS THE RADIUS OF THE END SURFACE OF A CAPILLARY TUBE END CONNECTOR UPON WHICH THE MATING SURFACE SEATS. 2D AND 1B MODE REPLY21AA051AC20 AKCNJ /D/ 10VOLTAGE RATING IN VOLTS,ANTICIPATOR ANTICIPATOR VOLTAGE RATING IN VOLTS THE VOLTAGE FOR WHICH THE ELECTRICAL ANTICIPATOR /HEATER/ IS RATED,EXPRESSED IN VOLTS. 2D AND 1B MODE REPLY21AB621AC20 AKCPL 16STYLE,MECHANISM,ENGAGING ENGAGING MECHANISM STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ENGAGING MECHANISM. 1L MODE REPLY 0 AKCQB 10ANGULAR DEVIATION IN DEG,ENGAGING MECHANISM OPENING ENGAGING MECHANISM OPENING ANGULAR DEVIATION IN DEG THE AMOUNT OF ROTATION OF THE OPENING IN THE DRIVE HOUSING FROM THE HORIZONTAL PLANE,IN A CLOCKWISE DIRECTION,NECESSARY TO ENABLE THE STARTER PINION TO ENGAGE THE FLYWHEEL RING GEAR,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AKCRD 11METHOD,ACTUATION,LEVER LEVER ACTUATION METHOD THE MEANS BY WHICH THE LEVER IS ACTUATED. SELECT REPLY CODE 10AA77 AKCSB 10CURRENT RATING IN AMPS,TEST,LOCK LOCK TEST CURRENT RATING IN AMPS THE MAXIMUM CURRENT MEASURED UNDER ESTABLISHED STALL CONDITIONS OF THE MOTOR,EXPRESSED IN AMPERES. 1B MODE REPLY 0 AKCTD 05DIRECTION,ROTATION,SHAFT SHAFT ROTATION DIRECTION THE DIRECTION OF ROTATION OF A ROTATING SHAFT AS VIEWED FROM THE DRIVE END. SELECT REPLY CODE 10AC84 AKCUL 16STYLE,ARRANGEMENT,SECOND LEG HOLE SECOND LEG HOLE ARRANGEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE SECOND LEG HOLES. 1L MODE REPLY 0 AKCVD 18TYPE,DRIVE DRIVE TYPE INDICATES THE TYPE OF DRIVE FOR TURNING,ROTATING,OR POSITIONING THE MECHANISM. SELECT REPLY CODE 10AG25 AKCWD 18TYPE,DEVICE,ARMATURE ACTUATION ARMATURE ACTUATION DEVICE TYPE INDICATES THE TYPE OF DEVICE THAT ACTUATES THE ROTATION OF THE ARMATURE. SELECT REPLY CODE 10AE34 AKCXD 19RELATIONSHIP,POSITIONAL,ENGAGING MECHANISM TO ARMATURE ENGAGING MECHANISM TO ARMATURE POSITIONAL RELATIONSHIP THE POSITIONAL RELATIONSHIP OF THE AXIS OF THE ENGAGING MECHANISM TO THE AXIS OF THE ARMATURE. SELECT REPLY CODE 10AG26 AKCYD /D/ 07FEATURE,REDUCTION,GEAR GEAR REDUCTION FEATURE AN INDICATION OF WHETHER OR NOT A MEANS OF CONVERTING THE HIGH SPEED LOW TORQUE OF THE MOTOR SHAFT TO A LOW SPEED HIGH TORQUE REQUIRED FOR CRANKING THE ENGINE IS INCLUDED. SELECT REPLY CODE 10AA49 AKCZL /D/ 16STYLE DESIGNATOR,CONTOUR,OUTER OUTER CONTOUR STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE OUTER CONTOUR. 1L MODE REPLY 0 AKDAG 19APPLICATION,ENGINE,SPECIFIC SPECIFIC ENGINE APPLICATION THE SPECIFIC ENGINE FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 AKDBB 10ANGULAR DEVIATION IN DEG,FLANGE,MOUNTING MOUNTING FLANGE ANGULAR DEVIATION IN DEG NONE. 1B MODE REPLY 0 AKDCB 10ANGULAR DEVIATION IN DEG,FIRST MOUNTING HOLE FIRST MOUNTING HOLE ANGULAR DEVIATION IN DEG NONE. 1B MODE REPLY 0 AKDDB 10ANGULAR DEVIATION IN DEG,FIRST TO SECOND MOUNTING HOLE FIRST TO SECOND MOUNTING HOLE ANGULAR DEVIATION IN DEG NONE. 1B MODE REPLY 0 AKDEJ 04DISTANCE BETWEEN SHAFT CENTER AND MOUNTING HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SHAFT CENTER AND MOUNTING HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKDFD /D/ 09MATERIAL,HOUSING,SENSITIVE SWITCH SENSITIVE SWITCH HOUSING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SENSITIVE SWITCH HOUSING IS FABRICATED. SELECT REPLY CODE 10AD09 AKDGD /D/ 09MATERIAL,SUPPORT,CONTACT CONTACT SUPPORT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PRIMARY SUPPORT FOR THE CONTACT/S/ IS FABRICATED. SELECT REPLY CODE 10AD09 AKDHJ /D/ 10CURRENT RATING IN AMPS,ANTICIPATOR ANTICIPATOR CURRENT RATING IN AMPS THE CURRENT FOR WHICH THE ELECTRICAL ANTICIPATOR /HEATER/ IS RATED,EXPRESSED IN AMPERES. 2D AND 1B MODE REPLY21AB621AC20 AKDJD 18TYPE,MOVER,PRIME PRIME MOVER TYPE INDICATES THE TYPE OF PRIME MOVER INCLUDED WITH THE UNIT. SELECT REPLY CODE 10AG27 AKDKJ /D/ 04DISTANCE BETWEEN ACTUATOR AND NEAREST MOUNTING HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN ACTUATOR AND NEAREST MOUNTING HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKDLL /D/ 16STYLE,BLADE HOLDER BLADE HOLDER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BLADE HOLDER. 1L MODE REPLY 0 AKDML 16STYLE DESIGNATOR,SPOUT SPOUT STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SPOUT. 1L MODE REPLY 0 AKDNL 16STYLE DESIGNATOR,HOLDER HOLDER STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HOLDER. 1L MODE REPLY 0 AKDPL 16STYLE,TOOTH,SOLID SOLID TOOTH STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SOLID TOOTH. 1L MODE REPLY 0 AKDQA /D/ 13THREAD CLASS,ATTACHMENT ATTACHMENT THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE,AND AN EXTERNAL OR INTERNAL THREAD. 1A MODE REPLY 0 AKDRD /D/ 13THREAD DIRECTION,ATTACHMENT ATTACHMENT THREAD DIRECTION THE DIRECTION OF THE ATTACHMENT THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 AKDSJ /D/ 13SCREW THREAD LENGTH,ATTACHMENT ATTACHMENT SCREW THREAD LENGTH A MEASUREMENT OF THE EXTENT OF ATTACHMENT SCREW THREADS,INCLUDING INCOMPLETE SCREW THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL THREAD AXIS. 2D AND 1B MODE REPLY21AA051AC20 AKDTJ /D/ 04LENGTH,OVERALL,THIMBLE THIMBLE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE THIMBLE. 2D AND 1B MODE REPLY21AA051AC20 AKDUJ 04SIZE,SHANK,NOMINAL NOMINAL SHANK SIZE THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL SIZE OF THE SHANK. 1D AND 1B MODE REPLY11AA05 AKDVA /D/ 12QUANTITY,PORT,ELECTRICAL ACCESS ELECTRICAL ACCESS PORT QUANTITY THE NUMBER OF HOLES OR OPENINGS PROVIDED IN THE ITEM FOR THE ENTRY OF ELECTRICAL WIRING. 1A MODE REPLY 0 AKDWJ /D/ 04DIAMETER,PORT,UNTHREADED ELECTRICAL ACCESS UNTHREADED ELECTRICAL ACCESS PORT DIAMETER THE DIAMETER OF THE UNTHREADED HOLE/S/ OR OPENING/S/ PROVIDED FOR THE ENTRY OF ELECTRICAL WIRING. 2D AND 1B MODE REPLY21AA051AC20 AKDXA 12QUANTITY,WINDING WINDING QUANTITY THE NUMBER OF INDIVIDUAL /NOT ELECTRICALLY CONNECTED/ WINDINGS. 1A MODE REPLY 0 AKDYJ A19ARRANGEMENT,CONTACT,SWITCH SWITCH CONTACT ARRANGEMENT THE DESIGNATION THAT IDENTIFIES THE SCHEMATIC DIAGRAM OF THE ELECTRICAL CONFIGURATION OF A SWITCH INCLUDING THE NUMBER OF SWITCHING POLES OR FORMS. 1D AND 1A MODE REPLY12AG28 AKDZD 18TYPE,ELEMENT,RESISTOR RESISTOR ELEMENT TYPE INDICATES THE TYPE OF RESISTANCE ELEMENT AS DETERMINED BY ITS CONSTRUCTION. SELECT REPLY CODE 10AE09 AKEAJ /D/ 04DIAMETER,INSIDE,PRESSURE CONNECTOR PRESSURE CONNECTOR INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PRESSURE CONNECTOR,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKEBJ /D/ 10FREQUENCY RATING IN HERTZ,CONTACT CONTACT FREQUENCY RATING IN HERTZ THE FREQUENCY AT WHICH THE CONTACTS ARE RATED,EXPRESSED IN HERTZ. 1D AND 1B MODE REPLY12AG16 AKECJ /D/ 10PRESSURE,BURST,SENSING ELEMENT SENSING ELEMENT BURST PRESSURE THE PRESSURE AT WHICH THE PRESSURE SENSING ELEMENT OF THE ITEM IS RENDERED INOPERATIVE BY RUPTURE OR OTHER PERMANENT PHYSICAL DAMAGE. 1D AND 1B MODE REPLY11AB18 AKEDD /D/ 13SCREW THREAD SERIES DESIGNATOR,FACILITY,CONNECTION CONNECTION FACILITY SCREW THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER ON THE CONNECTION FACILITY. PLEASE USE MRC AJYP IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AH06 AKEEJ /D/ 13SCREW THREAD DIAMETER,FACILITY,CONNECTION CONNECTION FACILITY SCREW THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CONNECTION FACILITY SCREW THREAD,AND TERMINATES AT THE CIRCUMFERENCE. PLEASE USE MRC CRFL IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 AKEFA 13THREAD CLASS,FACILITY,CONNECTION CONNECTION FACILITY THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE,AND AN EXTERNAL OR INTERNAL THREAD ON THE CONNECTION FACILITY. 1A MODE REPLY 0 AKEGJ /D/T13THREAD PITCH DIAMETERS,FACILITY,CONNECTION CONNECTION FACILITY THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD ON THE CONNECTION FACILITY. 1D AND 1F MODE REPLY11AA05 AKEHD 13THREAD DIRECTION,FACILITY,CONNECTION CONNECTION FACILITY THREAD DIRECTION THE DIRECTION OF THE CONNECTION FACILITY THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 AKEJD 13SCREW THREAD SERIES DESIGNATOR,FACILITY,MOUNTING MOUNTING FACILITY SCREW THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER ON THE MOUNTING FACILITY. SELECT REPLY CODE 10AH06 AKEKJ 04SCREW THREAD DIAMETER,FACILITY,MOUNTING MOUNTING FACILITY SCREW THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COAXIAL CYLINDER,WHICH WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD ON THE MOUNTING FACILITY,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKELH /D/ 09MATERIAL AND LOCATION MATERIAL AND LOCATION THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ITEM IS FABRICATED,EXCLUDING AND SURFACE TREATMENT,AND ITS LOCATION. PLEASE USE MRC MALC IN PLACE OF THIS DISCONTINUED MRC. 2D MODE REPLY 26AD092AE46 AKEMJ T13THREAD PITCH DIAMETERS,FACILITY,MOUNTING MOUNTING FACILITY THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD ON THE MOUNTING FACILITY. 1D AND 1F MODE REPLY11AA05 AKENB /D/ 13SCREW THREAD QUANTITY PER INCH,FACILITY,MOUNTING MOUNTING FACILITY SCREW THREAD QUANTITY PER INCH A MEASUREMENT OF THE NUMBER OF SCREW THREADS ON THE MOUNTING FACILITY PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1B MODE REPLY 0 AKEPB 13SCREW THREAD QUANTITY PER INCH,FACILITY,CONNECTION CONNECTION FACILITY SCREW THREAD QUANTITY PER INCH A MEASUREMENT OF THE NUMBER OF SCREW THREADS ON THE CONNECTION FACILITY PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1B MODE REPLY 0 AKEQH /D/ 17SURFACE TREATMENT AND LOCATION SURFACE TREATMENT AND LOCATION THE PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE ITEM,AND ITS LOCATION. 2D MODE REPLY 26AD092AE46 AKERD 18TYPE,MOUNTING,HINGE HINGE MOUNTING TYPE INDICATES THE TYPE OF HINGE WHICH PERMITS EITHER MORTISE OR SURFACE MOUNTING. SELECT REPLY CODE 10AG29 AKESD 07REMOVABILITY,PIN PIN REMOVABILITY AN INDICATION OF WHETHER OR NOT THE PIN IS REMOVABLE. SELECT REPLY CODE 10AC29 AKETD /D/ 07PIN,RISING RISING PIN AN INDICATION OF WHETHER OR NOT A RISING PIN IS INCLUDED. SELECT REPLY CODE 10AA49 AKEUL 16END STYLE,SHAFT CONNECTING SHAFT CONNECTING END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SHAFT CONNECTING END. 1L MODE REPLY 0 AKEVL 16STYLE,TIP,PIN PIN TIP STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PIN TIP. 1L MODE REPLY 0 AKEWD /D/ 07PIN,HINGE HINGE PIN AN INDICATION OF WHETHER OR NOT A HINGE PIN IS INCLUDED. SELECT REPLY CODE 10AA49 AKEXA 12QUANTITY,KNUCKLE KNUCKLE QUANTITY THE NUMBER OF CYLINDRICAL PROJECTIONS THROUGH WHICH AN AXIS OR PIN PASSES. 1A MODE REPLY 0 AKEYL 16STYLE,STAPLE STAPLE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE STAPLE. 1L MODE REPLY 0 AKEZJ 04DISTANCE FROM CENTERLINE TO CONNECTOR END DISTANCE FROM CENTERLINE TO CONNECTOR END NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFAJ 04DISTANCE FROM CENTERLINE TO CABLE END DISTANCE FROM CENTERLINE TO CABLE END NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFBJ 04LENGTH,LEAF,SLOTTED SLOTTED LEAF LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFCJ 04WIDTH,LEAF LEAF WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFDJ 04LENGTH,LEAF,FIXED FIXED LEAF LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFEJ /D/ 04DISTANCE,PIN CENTER TO SLOT CENTER PIN CENTER TO SLOT CENTER DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFFJ 04DISTANCE,VERTICAL,LEAF OUTER EDGE TO HOLE CENTER LEAF OUTER EDGE TO HOLE CENTER VERTICAL DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFGD /D/ 07QUALITY,FOLDING FOLDING QUALITY AN INDICATION OF WHETHER OR NOT THE ITEM HAS THE ABILITY TO WITHSTAND REPEATED FOLDING. SELECT REPLY CODE 10AA49 AKFHJ 04LENGTH,KNUCKLE KNUCKLE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFJJ 04LENGTH,KNUCKLE,END END KNUCKLE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFKJ 04DISTANCE,PIN CENTER TO BODY EDGE PIN CENTER TO BODY EDGE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFLJ 04WIDTH,LEAF,JAMB JAMB LEAF WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFMJ 04WIDTH,LEAF,DOOR DOOR LEAF WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFNJ 04DISTANCE,PIN CENTER TO JAMB LEAF EDGE PIN CENTER TO JAMB LEAF EDGE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFPJ 04DISTANCE,PIN CENTER TO DOOR LEAF EDGE PIN CENTER TO DOOR LEAF EDGE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFQJ 04DISTANCE,OFFSET,JAMB LEAF JAMB LEAF OFFSET DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFRJ 04DISTANCE,OFFSET,DOOR LEAF DOOR LEAF OFFSET DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFSJ 04DIAMETER,INSIDE,KNUCKLE KNUCKLE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFTJ 04DISTANCE FROM PIN CENTER TO OFFSET JAMB LEAF EDGE,DEVELOPED DEVELOPED DISTANCE FROM PIN CENTER TO OFFSET JAMB LEAF EDGE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFUD 09MATERIAL,ENVELOPE ENVELOPE MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF THE ENVELOPE IS FABRICATED. SELECT REPLY CODE 10MA01 AKFVJ 04DISTANCE FROM PIN CENTER TO OFFSET DOOR LEAF EDGE,DEVELOPED DEVELOPED DISTANCE FROM PIN CENTER TO OFFSET DOOR LEAF EDGE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKFWD /D/ 18TYPE,PRESERVATIVE,LEATHER LEATHER PRESERVATIVE TYPE INDICATES THE TYPE OF PRESERVATIVE APPLIED TO THE LEATHER. SELECT REPLY CODE 10AG31 AKFXD 19PROCESS,TANNING TANNING PROCESS THE PROCESS BY WHICH HIDES ARE TURNED INTO LEATHER. SELECT REPLY CODE 10AG36 AKFYH /D/ 19CONDITION AND LOCATION,SURFACE SURFACE CONDITION AND LOCATION THE CONDITION OF THE ITEM WITH RESPECT TO THE TEXTURE OF THE SURFACE,AND ITS LOCATION. 2D MODE REPLY 23AJ912AG33 AKFZH /D/ 09MATERIAL AND LOCATION,COVERING COVERING MATERIAL AND LOCATION THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE COVERING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT,AND A DESIGNATION OF THAT PORTION OF THE ITEM TO WHICH THE COVERING MATERIAL IS APPLICABLE. 2D MODE REPLY 26AD093AJ91 AKGAJ /D/ 04THICKNESS,NOMINAL,PULLEY SURFACE COVER PULLEY SURFACE COVER NOMINAL THICKNESS THE NOMINAL MEASUREMENT OF THE SMALLEST DIMENSION OF A PULLEY SURFACE COVER. 1D AND 1B MODE REPLY11AA05 AKGBJ /D/ 04THICKNESS,NOMINAL,TOP SURFACE COVER TOP SURFACE COVER NOMINAL THICKNESS A NOMINAL MEASUREMENT OF THE SMALLEST DIMENSION OF THE TOP SURFACE COVER,IN DISTINCTION FROM HEIGHT OR WIDTH. 1D AND 1B MODE REPLY11AA05 AKGCJ /D/A10STRENGTH,TENSILE,PULLEY SURFACE PULLEY SURFACE TENSILE STRENGTH THE MAXIMUM LOAD IN TENSION APPLIED IN A LONGITUDINAL DIRECTION,PER UNIT OF CROSS-SECTIONAL AREA,THAT THE PULLEY SURFACE CAN WITHSTAND WITHOUT RUPTURE. 1D AND 1A MODE REPLY11AB18 AKGDJ /D/A10STRENGTH,TENSILE,TOP SURFACE TOP SURFACE TENSILE STRENGTH THE MAXIMUM LOAD IN TENSION APPLIED IN LONGITUDINAL DIRECTION,PER UNIT OF CROSS-SECTIONAL AREA,THAT THE TOP SURFACE CAN WITHSTAND WITHOUT RUPTURE. 1D AND 1A MODE REPLY11AB18 AKGED 04SIZE,CROSS-SECTIONAL CROSS-SECTIONAL SIZE THE CROSS-SECTIONAL SIZE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND DESIGNATED. SELECT REPLY CODE 10AG34 AKGFJ 04WIDTH,NOMINAL NOMINAL WIDTH A NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AKGGJ 04LENGTH,NOMINAL NOMINAL LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AKGHJ 04LENGTH,PITCH,NOMINAL NOMINAL PITCH LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM,TAKEN ALONG THE PITCH LINE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AKGJJ 04LENGTH,OUTSIDE,EFFECTIVE,NOMINAL NOMINAL EFFECTIVE OUTSIDE LENGTH THE NOMINAL EFFECTIVE OUTSIDE LENGTH OF AN ITEM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AKGKJ 10CIRCUMFERENCE,INSIDE,NOMINAL NOMINAL INSIDE CIRCUMFERENCE THE NOMINAL DISTANCE AROUND THE INSIDE SURFACE OF THE ITEM. 1D AND 1B MODE REPLY11AA05 AKGLD 18TYPE,COUPLING,BELT BELT COUPLING TYPE INDICATES THE TYPE OF MECHANICAL COUPLING USED TO SECURE THE ENDS OF BELTING TOGETHER. SELECT REPLY CODE 10AG35 AKGMA 12QUANTITY,BELT BELT QUANTITY THE NUMBER OF BELTS PROVIDED. 1A MODE REPLY 0 AKGNJ A18TYPE AND QUANTITY,DRIVE DRIVE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF DRIVES PROVIDED. 1D AND 1A MODE REPLY12AG25 AKGPD 18TYPE,FILM FILM TYPE THE PRIMARY GROUPING WHICH INDICATES THE APPLICATION OF THE FILM. SELECT REPLY CODE 10AG37 AKGQJ 04DISTANCE,PITCH,NOMINAL NOMINAL PITCH DISTANCE A NOMINAL MEASUREMENT OF THE CENTER TO CENTER DISTANCE BETWEEN TEETH OR PINS,TAKEN ALONG THE PITCH LINE. 1D AND 1B MODE REPLY11AA05 AKGRD 19SUBTYPE,FILM FILM SUBTYPE A CATEGORY WITHIN THE PRIMARY GROUPING BY WHICH FILM IS IDENTIFIED. SELECT REPLY CODE 10AG32 AKGSD 18TYPE,EMULSION EMULSION TYPE INDICATES THE TYPE OF REPRODUCED IMAGE. SELECT REPLY CODE 10AG38 AKGTD 18TYPE,REPRODUCTION REPRODUCTION TYPE INDICATES THE TYPE OF IMAGE DESIGNED TO APPEAR ON THE MATERIAL AFTER EXPOSURE AND DEVELOPMENT. SELECT REPLY CODE 10AG39 AKGUL 16STYLE DESIGNATOR,INDIVIDUAL STACK CIRCUIT CONNECTION INDIVIDUAL STACK CIRCUIT CONNECTION STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE INDIVIDUAL STACK CIRCUIT CONNECTION. 1L MODE REPLY 0 AKGVD /D/ 19LEADER,FILM FILM LEADER THE INTEGRAL OR SPLICED PORTION AT THE BEGINNING OR LEADING END OF THE ROLL,FACILITATING THREADING AND VIEWING. SELECT REPLY CODE 10AG40 AKGWD 19SENSITIVITY,EMULSION EMULSION SENSITIVITY THE DEGREE OF RADIANT ENERGY TO WHICH THE EMULSION IS DESIGNED TO REACT TO FORM A LATENT IMAGE UNDER GIVEN EXPOSURE CONDITIONS. SELECT REPLY CODE 10AG41 AKGXA 10POWER,RESOLVING RESOLVING POWER THE DEGREE OF IMAGE DETAIL EXPRESSED IN LINES PER MILLIMETER THAT A SENSITIZED MATERIAL IS CAPABLE OF REPRODUCING. 1A MODE REPLY 0 AKGYD 18TYPE,PROCESS,DIAZO DIAZO PROCESS TYPE INDICATES THE TYPE OF PROCESS USED IN THE DIAZO PRINT DEVELOPMENT. SELECT REPLY CODE 10AG42 AKGZJ A10INDEX,EXPOSURE EXPOSURE INDEX A NUMERIC VALUE BASED ON THE DEGREE AND SPEED TO WHICH A PHOTOSENSITIVE MATERIAL REACTS WHEN EXPOSED TO A SPECIFIC LIGHT SOURCE. 2D AND 1A MODE REPLY22AG442AG43 AKHAD 03DESIGNATION,WEIGHT,PAPER PAPER WEIGHT DESIGNATION THE WEIGHT DESIGNATION OF THE UNPROCESSED PAPER BASED ON THE THICKNESS OF THE PAPER STOCK. SELECT REPLY CODE 10AG45 AKHBA 12QUANTITY,EXPOSURE,FILM FILM EXPOSURE QUANTITY THE NUMBER OF INDIVIDUAL FRAMES /EXPOSURE SECTIONS/ CONTAINED IN A FILM. 1A MODE REPLY 0 AKHCD 18TYPE,DEVICE,WINDING WINDING DEVICE TYPE INDICATES THE TYPE OF WINDING DEVICE ON WHICH THE ITEM IS WOUND. SELECT REPLY CODE 10AG46 AKHDD 08LOCATION,EMULSION EMULSION LOCATION INDICATES WHETHER THE ITEM IS WOUND WITH THE EMULSION INWARD OR OUTWARD. SELECT REPLY CODE 10AC50 AKHEJ 04HEIGHT,OVERALL,EARPHONE EARPHONE OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AKHFJ 04WIDTH,OVERALL,EARPHONE EARPHONE OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKHGD /D/ 08LOCATION,PERFORATION PERFORATION LOCATION INDICATES THE LOCATION OF THE PERFORATIONS ON THE ITEM. SELECT REPLY CODE 10AE46 AKHHG /D/ 03DESIGNATOR,IDENTIFICATION,PERFORATION PERFORATION IDENTIFICATION DESIGNATOR THE STANDARD PART NUMBER OR DESIGNATOR WHICH IDENTIFIES THE TYPE OF PERFORATIONS. FULL TEXT WRITE-IN 0 AKHJD /D/ 19COATING,ANTIREFLECTION ANTIREFLECTION COATING AN INDICATION OF THE COATING APPLIED TO THE ITEM TO PREVENT HALOS OR GHOST IMAGES. SELECT REPLY CODE 10AG47 AKHKD 01COLOR,IMAGE IMAGE COLOR THE HUE OR COLORING OF THE CONTINUOUS TONE OR LINE COPY IMAGE AS IT IS DESIGNED TO APPEAR ON THE ITEM. SELECT REPLY CODE 10AD06 AKHLD /D/ 08LOCATION,COATING,SENSITIZED SENSITIZED COATING LOCATION INDICATES THE LOCATION OF THE SENSITIZED COATING ON THE ITEM. SELECT REPLY CODE 10AE46 AKHMD 08LOCATION,SURFACE,MATTE MATTE SURFACE LOCATION INDICATES THE LOCATION OF THE MATTE SURFACE. SELECT REPLY CODE 10AE46 AKHND 10SPEED,PRINTING,REPRODUCTION REPRODUCTION PRINTING SPEED THE RATE,DETERMINED BY THE FEET PER MINUTE OF THE PRINTERS OPERATION,AT WHICH THE MATERIAL IS DESIGNED TO BE EXPOSED FOR THE REQUIRED IMAGE REPRODUCTION. SELECT REPLY CODE 10AG48 AKHPD /D/ 07FEATURE,INTERFILABILITY INTERFILABILITY FEATURE THE ABILITY OF CERTAIN SENSITIZED MATERIAL TO BE INTERFILED WITH IRON SILVER BROWN PRINT WITHOUT ADVERSE CHEMICAL REACTION. SELECT REPLY CODE 10AA49 AKHQD /D/ 07QUALITY,RESISTANCE,WATER WATER RESISTANCE QUALITY AN INDICATION OF WHETHER OR NOT A QUALITY TO RESIST WATER IS INCLUDED. SELECT REPLY CODE 10AA49 AKHRD /D/ 10SHRINKABILITY SHRINKABILITY THE DIMENSIONAL CHANGE OCCURRING DURING USAGE AND/OR PROCESSING. SELECT REPLY CODE 10AH10 AKHSD /D/ 19TONE,IMAGE IMAGE TONE THE DEGREE OF IMAGE WARMTH DESIGNED TO APPEAR ON THE FINISHED PRINT. SELECT REPLY CODE 10AG49 AKHTD 18TYPE,IMAGE IMAGE TYPE THE FORM IN WHICH THE IMAGE IS REPRODUCED. SELECT REPLY CODE 10AG50 AKHUG 13THREAD SIZE,MOUNTING SPINDLE MOUNTING SPINDLE THREAD SIZE DESIGNATES THE MOUNTING SPINDLE THREAD SERIES AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. FULL TEXT WRITE-IN 0 AKHVD /D/ 07COATING,RESISTANT,ABRASION ABRASION RESISTANT COATING AN INDICATION OF WHETHER OR NOT AN ABRASION RESISTANT COATING IS INCLUDED ON THE ITEM. SELECT REPLY CODE 10AA49 AKHWD 19CHARACTERISTIC,LOADING LOADING CHARACTERISTIC INDICATES IF THE ITEM MAY BE INSERTED INTO THE APPARATUS IN DAYLIGHT OR REQUIRES DARKROOM CONDITION. SELECT REPLY CODE 10AG51 AKHXA 19LIMIT,PERCENTAGE,STORAGE HUMIDITY STORAGE HUMIDITY PERCENTAGE LIMIT THE HUMIDITY CONDITIONS THAT WILL ADEQUATELY PROTECT AN ITEM OF SUPPLY DURING STORAGE. 1A MODE REPLY 0 AKHYD /D/ 07PREHARDENER,EMULSION EMULSION PREHARDENER AN INDICATION OF WHETHER OR NOT AN EMULSION PREHARDENER FOR HIGH TEMPERATURE DEVELOPMENT IS INCLUDED. SELECT REPLY CODE 10AA49 AKHZD 10CONTRAST RATING CONTRAST RATING A RATING,ESTABLISHED BY EACH MANUFACTURER,BASED ON THE TOTAL DENSITY RANGE AVAILABLE IN THE MATERIAL AND THE SPEED AT WHICH THE DENSITY INCREASES UPON EXPOSURE. SELECT REPLY CODE 10AG52 AKJAJ 10STRENGTH,MEDICINAL,ACTIVE MEDICAMENT ACTIVE MEDICAMENT MEDICINAL STRENGTH THE INGREDIENTS COMPOUNDED IN A PHARMACEUTICAL PREPARATION AND RECOGNIZED AS HAVING THERAPEUTIC VALUE/S/. /USUALLY REPRESENTATIVE IN THE ITEM NAME GENERIC NOMENCLATURE./ 3D AND 1B MODE REPLY32AG535AG542AG55 AKJBJ A10RATIO,CONCENTRATION,ACTIVE MEDICAMENT ACTIVE MEDICAMENT CONCENTRATION RATIO THE AMOUNT OF A GIVEN SUBSTANCE IN A STATED UNIT OF A MIXTURE,SOLUTION,OR ORE. 1D AND 1A MODE REPLY15AG54 AKJCD 18TYPE,CAPSULE CAPSULE TYPE INDICATES THE TYPE OF CONTAINER OR SHELL USED TO ENCAPSULATE THE ITEM. SELECT REPLY CODE 10AG56 AKJDD /D/ 18TYPE,COATING,MEDICAMENT MEDICAMENT COATING TYPE INDICATES THE PROCESSES AND TECHNIQUES EMPLOYED IN THE COATING OF MEDICAMENTS. SELECT REPLY CODE 10AG57 AKJED /D/ 19FEATURE,PREPARATION,TABLET TABLET PREPARATION FEATURE RECOGNIZED METHODS OR TECHNIQUES OF TABLET PREPARATION. SELECT REPLY CODE 10AG58 AKJFD 11METHOD,ACTION,LONG LONG ACTION METHOD THE MEANS USED TO EXTEND PERIODS OF DOSAGE. SELECT REPLY CODE 10AG59 AKJGD /D/ 11METHOD,ADMINISTERING ADMINISTERING METHOD RECOGNIZED METHODS FOR ADMINISTERING DRUGS TO ATTAIN A DESIRED THERAPEUTIC EFFECT,BASED ON PHYSICAL/CHEMICAL FACTORS RELATIVE TO THE BODY AND/OR DRUG FORMULATION. SELECT REPLY CODE 10AG60 AKJHJ 04WIDTH,SHAFT SHAFT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SHAFT, IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AKJJD /D/ 18TYPE,STORAGE STORAGE TYPE INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS. SELECT REPLY CODE 10AD41 AKJKJ 04DIAMETER,CROSS HOLE,SHAFT SHAFT CROSS HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHAFT CROSS HOLE, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKJLD 18TYPE,SUPPOSITORY SUPPOSITORY TYPE SOLID MEDICINAL BODIES OF DIFFERENT SHAPES AND SIZES DESIGNED TO MELT,SOFTEN,OR DISSOLVE AT BODY TEMPERATURES. SELECT REPLY CODE 10AG61 AKJMD 18TYPE,BASE,MEDICAMENT MEDICAMENT BASE TYPE THE SUPPORTING OR CARRYING INGREDIENT/S/ OR METHOD WHICH HELPS TO PROMOTE EFFICIENT RELEASE AND/OR ABSORPTION INTO THE CIRCULATORY SYSTEM,SOOTHE SURFACE TISSUE,LOCAL EFFECT,STIMULATION TO PERISTALSIS,AND THE LIKE. SELECT REPLY CODE 10AG62 AKJND /D/ 07APPLICATOR APPLICATOR AN INDICATION OF WHETHER OR NOT A SPECIAL DEVICE /OR INSERTER/ WHICH ALLOWS FOR PROPER INSERTION AND POSITIONING OF A MEDICAMENT INTO A MATERIAL BODY CAVITY OR INCISION IS INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA49 AKJPD /D/ 07ADDITIVE,BUFFER BUFFER ADDITIVE AN INDICATION OF WHETHER OR NOT AN AGENT WHICH ENHANCES THE ABILITY OF A SEPTIME,PARTICULARLY AN AQUEOUS SOLUTION,TO RESIST CHANGES OF PH ON ADDING ACID OR ALKALI,OR ON DILUTING WITH A SOLVENT,IS INCLUDED. SELECT REPLY CODE 10AA49 AKJQD 18TYPE,VEHICLE,PHARMACEUTICAL PHARMACEUTICAL VEHICLE TYPE THE LIQUID NONTOXIC COMPONENT FORM OF A PHARMACUETICAL PREPARATION WHICH NORMALLY HAS NO THERAPEUTIC ACTION,AND PRESENTS THE ACTIVE INGREDIENTS TO THE BODY FOR ABSORPTION. SELECT REPLY CODE 10AG63 AKJRD /D/ 07ADDITIVE,BACTERIOSTATIC BACTERIOSTATIC ADDITIVE AN INDICATION OF WHETHER OR NOT THE ITEM HAS A BACTERIOSTATIC ADDITIVE. SELECT REPLY CODE 10AA49 AKJSH /D/ 02DESIGN,COMPONENT,DISPERSION DISPERSION COMPONENT DESIGN THE TYPE OF INCLOSURE /CONTAINER/ FROM WHICH THE PARENTERAL FORMULATION IS WITHDRAWN OR EXPELLED. 2D MODE REPLY 22AG642AG65 AKJTA 19NUMBER,GAGE,NEEDLE NEEDLE GAGE NUMBER THE DIAMETER OF THE NEEDLE SHAFT AS DETERMINED BY THE UNIVERSAL STANDARD STUBS WIRE GAGE METHOD. 1A MODE REPLY 0 AKJUD 18MOTION,SANDING SANDING MOTION AN INDICATION OF THE SANDING OTION PRODUCED BY THE ITEM. SELECT REPLY CODE 10AF63 AKJVD /D/ 11METHOD,DESICCATION,LIQUID LIQUID DESICCATION METHOD AN INGENIOUS PROCESS ESPECIALLY DESIGNED FOR THE DESSICATION OF LIQUIDS. SELECT REPLY CODE 10AG82 AKJWD /D/ 07ANESTHETIC ANESTHETIC AN INDICATION OF WHETHER OR NOT AN AGENT IS INCLUDED TO PRODUCE A CONDITION OF ANESTHESIA. SELECT REPLY CODE 10AA49 AKJXD /D/ 07ADDITIVE,DILUENT DILUENT ADDITIVE AN INDICATION OF WHETHER OR NOT A DILUENT ADDITIVE IS INCLUDED. SELECT REPLY CODE 10AA49 AKJYD /D/ 19INGREDIENT,VEHICLE,NONAQUEOUS NONAQUEOUS VEHICLE INGREDIENT OILS OF VEGETABLE ORIGIN OR OTHER SUITABLE NONAQUEOUS /NONWATER/ VEHICLES WHICH CONFORM TO THE REQUIREMENTS AND INTENT,AS DESCRIBED IN OTHER VEHICLES UNDER INJECTION IN THE USP. SELECT REPLY CODE 10AG54 AKJZD /D/ 19INGREDIENT,BUFFERING BUFFERING INGREDIENT AGENT/S/ USED TO RESIST PH CHANGES IN THE FORMULATION. SELECT REPLY CODE 10AG54 AKKAD /D/ 19INGREDIENT,EMULSIFYING EMULSIFYING INGREDIENT AGENT/S/ USED TO MAKE AN EMULSION OF A FIXED OIL PREVENTING SEPARATION OF THE EMULSIONS TWO PHASE SYSTEM. SELECT REPLY CODE 10AG54 AKKBD /D/ 07ADDITIVE,FLAVOR FLAVOR ADDITIVE AN INDICATION OF WHETHER OR NOT THE ITEM HAS A FLAVOR ADDITIVE. SELECT REPLY CODE 10AA49 AKKCJ /D/A19D0SAGE,SEQUENTIAL SEQUENTIAL D0SAGE THE EMPLOYMENT OF TWO DIFFERENT TABLETS DURING THE PERIOD OF MEDICATION TO ENHANCE PHYSIOLOGICAL APPROACH. 2D AND 1A MODE REPLY22AG666AD06 AKKDD /D/ 19TRAILER,FILM FILM TRAILER THE INTEGRAL OR SPLICED PORTION AT THE TRAILING END OF THE ROLL FACILITATING THREADING,VIEWING,AND REWINDING. SELECT REPLY CODE 10AG40 AKKEJ 04THICKNESS,MATERIAL,BASE BASE MATERIAL THICKNESS THE MEASUREMENT OF THE SMALLEST DIMENSION OF THE BASE MATERIAL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AKKFJ 12QUANTITY WITHIN EACH UNIT PACKAGE QUANTITY WITHIN EACH UNIT PACKAGE THE NUMBER OF THE VOLUME,FORM,OR THE DOSAGE WITHIN EACH UNIT PACKAGE. 1D AND 1B MODE REPLY12AG67 AKKGD 19WRAPPING,SPECIAL SPECIAL WRAPPING THE UNIQUE CHARACTERISTIC NOT INHERENT TO THE TYPE OF INCLOSURE IN WHICH THE ITEM IS NORMALLY WRAPPED. SELECT REPLY CODE 10AG68 AKKHD /D/ 09MATERIAL,WARP,CLOTH CLOTH WARP MATERIAL THE SPECIFIC MATERIAL OF THE SPUN STAPLE OR FILAMENT/S/ OF THE YARNS THAT RUN LENGTHWISE IN A WOVEN FABRIC. SELECT REPLY CODE 10AD09 AKKJD /D/ 09MATERIAL,FILLING,CLOTH CLOTH FILLING MATERIAL THE SPECIFIC MATERIAL OF THE SPUN STAPLE OR FILAMENT/S/ OF THE YARNS THAT RUN CROSSWISE IN A WOVEN FABRIC. SELECT REPLY CODE 10AD09 AKKKJ 10WEIGHT,CLOTH CLOTH WEIGHT A DESIGNATION EXPRESSED IN UNITS OF WEIGHT PER SQUARE OR LINEAR YARD OF A SPECIFIED /BASIC/ WIDTH. 2D AND 1B MODE REPLY22AG691AC20 AKKLD /D/ 19FIBER FIBER THE NATURAL AND/OR MAN-MADE FIBER COMPRISING THE ITEM. SELECT REPLY CODE 10AD09 AKKMB /D/ 10PERCENT,FIBER FIBER PERCENT THE PERCENTAGE OF NATURAL AND/OR MAN-MADE FIBER/S/ COMPRISING THE ITEM. 1B MODE REPLY 0 AKKND 19NAME,CLOTH CLOTH NAME THE TERM(S) BY WHICH THE CLOTH IS KNOWN OR DESIGNATED,EXCLUDING SURFACE COATING. SELECT REPLY CODE 10AF82 AKKPB 12ORBITS PER MINUTE ORBITS PER MINUTE THE NUMBER OF ORBITS WHICH THE ITEM WILL OPERATE WITHIN A SPECIFIED PERIOD OF TIME. 1B MODE REPLY 0 AKKQD 18TYPE,PILE PILE TYPE INDICATES WHETHER THE ITEM HAS A SINGLE OR DOUBLE FACE PILE. SELECT REPLY CODE 10AG87 AKKRJ 04HEIGHT,PILE PILE HEIGHT THE HEIGHT OF THE PILE YARN FROM THE BASE TO ITS UPPER END. HEIGHT INCLUDES THE MEASUREMENT OF BOTH PILE YARNS IN A DOUBLE PILE ITEM. 1D AND 1B MODE REPLY11AA05 AKKSD /D/ 18TYPE,CONSTRUCTION,KNIT KNIT CONSTRUCTION TYPE THE METHOD OR PROCESS OF MANUFACTURING A FABRIC BY A SERIES OF INTERLOCKING LOOPS OF ONE OR MORE YARNS. SELECT REPLY CODE 10AD07 AKKTD 18TYPE,STITCH,KNIT KNIT STITCH TYPE INDICATES THE TYPE OF OPERATION FOR INTERLOCKING LOOPS OF YARN BY USE OF A NEEDLE(S). SELECT REPLY CODE 10AG71 AKKUJ 04DIAMETER,ORBIT ORBIT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ORBIT, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKKVD /D/ 08LOCATION,NAP NAP LOCATION INDICATES THE LOCATION OF AN ITEM TO WHICH A NAP IS APPLIED. SELECT REPLY CODE 10AE46 AKKWJ 10COUNT,MESH MESH COUNT THE NUMBER OF OPEN SPACES BETWEEN THE YARNS IN UNITS OF SQUARE MEASURE. 2D AND 1B MODE REPLY21AB391AC20 AKKXJ /D/ 04SIZE,MESH,WARP WARP MESH SIZE THE DISTANCE BETWEEN THE TWINE OR YARN IN THE WARP DIRECTION. 1D AND 1B MODE REPLY11AA05 AKKYJ /D/ 04SIZE,MESH,FILLING FILLING MESH SIZE THE DISTANCE BETWEEN THE TWINE OR YARN IN THE FILLING DIRECTION. 1D AND 1B MODE REPLY11AA05 AKKZD /D/ 07PROCESS,MERCERIZATION MERCERIZATION PROCESS AN INDICATION AS TO WHETHER OR NOT A PROCESS IS PROVIDED TO GIVE LUSTER AND STRENGTH AND TO MAKE AN ITEM MORE RECEPTIVE TO DYES. SELECT REPLY CODE 10AB22 AKLAD /D/ 19PROCESS,STABILITY,DIMENSIONAL DIMENSIONAL STABILITY PROCESS A PROCESS USED TO INSURE RETENTION OF SIZE AND SHAPE. SELECT REPLY CODE 10AG72 AKLBD /D/ 19QUALITY,LINT LINT QUALITY AN INDICATION OF WHETHER OR NOT AN ITEM PRODUCES LINT. SELECT REPLY CODE 10AG73 AKLCD /D/ 08MOUNTING LOCATION,HANDLE,AUXILIARY AUXILIARY HANDLE MOUNTING LOCATION INDICATES THE MOUNTING LOCATION OF THE AUXILIARY HANDLE(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 AKLDJ A10SPEED,BELT BELT SPEED THE DISTANCE THE BELT TRAVELS IN A GIVEN UNIT OF TIME. 1D AND 1A MODE REPLY11AA22 AKLEJ 04WIDTH,BIT EDGE BIT EDGE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BIT EDGE, IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AKLFD /D/ 12NUMBER OF ENGINES DISPLAYED NUMBER OF ENGINES DISPLAYED THE NUMBER OF ENGINES THAT SIMULTANEOUSLY DISPLAY DATA. SELECT REPLY CODE 10AD02 AKLGJ 10TIME AFTER MIXING,EFFECTIVE,MAXIMUM MAXIMUM EFFECTIVE TIME AFTER MIXING THE MAXIMUM EFFECTIVE TIME OF THE ITEM AFTER MIXING. 1D AND 1B MODE REPLY12AG67 AKLHH /D/ 09MATERIAL AND LOCATION,COATING COATING MATERIAL AND LOCATION THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE COATING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT,AND ITS LOCATION. 2D MODE REPLY 23AE466AD09 AKLJD /D/ 01COLOR,BRAID BRAID COLOR THE HUE OR TINT OF THE BRAID. SELECT REPLY CODE 10AD06 AKLKD /D/ 19SOURCE,SHADE,BRAID BRAID SHADE SOURCE THE NAME OF THE REFERENCE SOURCE OF THE BRAID SHADE IDENTIFICATION DESIGNATOR. SELECT REPLY CODE 10AF94 AKLLA /D/ 03DESIGNATOR,IDENTIFICATION,BRAID SHADE BRAID SHADE IDENTIFICATION DESIGNATOR A DESIGNATION ASSIGNED TO A PARTICULAR GRADATION OF A COLOR FOR PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 AKLMD 18TYPE,HEADWEAR HEADWEAR TYPE INDICATES THE TYPE OF HEADWEAR BY THE STYLE OR DESIGN. SELECT REPLY CODE 10AG74 AKLND 11METHOD,FASTENING,HEADWEAR HEADWEAR FASTENING METHOD THE MEANS BY WHICH THE HEADWEAR IS FASTENED TO THE WEARER. SELECT REPLY CODE 10AF69 AKLPD 11METHOD,ATTACHMENT,HEADWEAR HEADWEAR ATTACHMENT METHOD THE MEANS BY WHICH THE HEADWEAR IS FASTENED TO A GARMENT. SELECT REPLY CODE 10AF69 AKLQD 18TYPE,BRIM BRIM TYPE INDICATES THE TYPE OF BRIM BY THE STYLE OR DESIGN. SELECT REPLY CODE 10AG75 AKLRD /D/ 07VISOR VISOR AN INDICATION OF WHETHER OR NOT A VISOR IS INCLUDED. SELECT REPLY CODE 10AA49 AKLSD /D/ 07FLAPS,EAR EAR FLAPS AN INDICATION OF WHETHER OR NOT EAR FLAPS ARE INCLUDED. SELECT REPLY CODE 10AA49 AKLTD /D/ 07SNOOD SNOOD AN INDICATION OF WHETHER OR NOT A SNOOD IS INCLUDED. SELECT REPLY CODE 10AA49 AKLUJ 10TIME AFTER APPLICATION,EFFECTIVE,MAXIMUM MAXIMUM EFFECTIVE TIME AFTER APPLICATION THE MAXIMUM EFFECTIVE TIME AFTER APPLYING. 1D AND 1B MODE REPLY12AG67 AKLVD /D/ 07APRON,BACK BACK APRON AN INDICATION OF WHETHER OR NOT THE ITEM HAS A BACK APRON. SELECT REPLY CODE 10AA49 AKLWD 18TYPE,FACEPIECE FACEPIECE TYPE INDICATES A SHIELD FABRICATED FROM GLASS OR OTHER TRANSPARENT MATERIAL THAT PROTECTS THE FACE OF THE WEARER. SELECT REPLY CODE 10AG76 AKLXD /D/ 18TYPE,HOLDER,COVER GLASS COVER GLASS HOLDER TYPE INDICATES THE TYPE OF GLASS COVER HOLDER THAT PROTECTS THE FILTER PLATE. SELECT REPLY CODE 10AB89 AKLYA 10RESISTANCE IN VOLTS,SHOCK,ELECTRICAL ELECTRICAL SHOCK RESISTANCE IN VOLTS THE RATED RESISTANCE TO ELECTRICAL SHOCK OR BURN,EXPRESSED IN VOLTS. 1A MODE REPLY 0 AKLZD 19EQUIPMENT,COMMUNICATION COMMUNICATION EQUIPMENT THE IMPLEMENT/S/ USED FOR THE PURPOSE OF COMMUNICATION THAT ARE INSTALLED IN AND/OR ON THE ITEM. SELECT REPLY CODE 10AG77 AKMAJ /D/ 03DESIGNATION,WEIGHT,SUBSTANCE SUBSTANCE WEIGHT DESIGNATION A MEASUREMENT OF WEIGHT BASED ON THE SPECIFIC SIZE AND NUMBER OF SHEETS. 3D AND 1B MODE REPLY31AB101AC202AH05 AKMBD /D/ 09MATERIAL,NET NET MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE NETTING PORTION OF THE ITEM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AKMCJ A18TYPE AND QUANTITY,APERTURE APERTURE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF EACH DIFFERENT KIND OF OPENING. 1D AND 1A MODE REPLY12AG79 AKMDJ 04WIDTH ACROSS FLATS,TIP TIP WIDTH ACROSS FLATS THE SHORTEST STRAIGHT LINE BETWEEN FLATS ON THE TIP,PERPENDICULAR TO THE LENGTH OF THE TIP. 2D AND 1B MODE REPLY21AA051AC20 AKMED /D/ 19NAME,CLOTH,NET NET CLOTH NAME A NOUN,WITH OR WITHOUT MODIFIERS,BY WHICH THE CLOTH THAT COMPRISES THE NETTING PORTION OF AN ITEM IS KNOWN OR DESIGNATED. SELECT REPLY CODE 10AF82 AKMFD /D/ 17SURFACE TREATMENT,CORE CORE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE CORE SURFACE. SELECT REPLY CODE 10AD09 AKMGJ 13THREAD LENGTH,NOMINAL NOMINAL THREAD LENGTH A NOMINAL MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS. 1D AND 1B MODE REPLY11AA05 AKMHJ 04DIAMETER,CORE CORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CORE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKMJJ 04LENGTH,CORE CORE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CORE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AKMKJ 04WIDTH,CORE CORE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CORE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AKMLJ 04THICKNESS,CORE CORE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE CORE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AKMMJ 04DIAMETER,HOLE,CORE CORE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AKMNJ /D/ 04DISTANCE FROM TOP OF ANODE TO TOP OF STRAP DISTANCE FROM TOP OF ANODE TO TOP OF STRAP NONE. 2D AND 1B MODE REPLY21AA051AC20 AKMPJ 04DISTANCE FROM EDGE TO CENTER OF CORE HOLE DISTANCE FROM EDGE TO CENTER OF CORE HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKMQJ 04DISTANCE FROM EDGE TO CENTER OF FIRST HOLE DISTANCE FROM EDGE TO CENTER OF FIRST HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKMRJ 04DISTANCE FROM EDGE TO CENTER OF SECOND HOLE DISTANCE FROM EDGE TO CENTER OF SECOND HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKMSJ 04DISTANCE FROM EDGE TO CENTER OF THIRD HOLE DISTANCE FROM EDGE TO CENTER OF THIRD HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKMTJ 04DISTANCE FROM EDGE TO CENTER OF FOURTH HOLE DISTANCE FROM EDGE TO CENTER OF FOURTH HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKMVD /D/ 07PERFORATION,CAMERA,HIGH SPEED HIGH SPEED CAMERA PERFORATION AN INDICATION OF WHETHER OR NOT ROLL MATERIAL PERFORATION FOR HIGH SPEED CAMERA USE IS INCLUDED. SELECT REPLY CODE 10AA49 AKMWD /D/ 19RELATIONSHIP,WIND,PERFORATION PERFORATION WIND RELATIONSHIP AN INDICATION OF THE DIRECTION THE FILM WILL UNWIND IN RELATION TO THE PERFORATIONS. SELECT REPLY CODE 10AG80 AKMXD 07STERILITY STERILITY AN INDICATION OF WHETHER OR NOT THE ITEM IS FREE OF LIVING ORGANISMS. SELECT REPLY CODE 10AG96 AKMYD 19FORM,USAGE USAGE FORM THE READY-TO-USE SHAPE OR CONFIGURATION OF AN ITEM. SELECT REPLY CODE 10AE98 AKMZJ 10LOAD RATING,STATIC STATIC LOAD RATING THE WEIGHT APPLIED TO AN ITEM TO MEASURE IS ABILITY TO SUPPORT A COMPONENT. 2D AND 1B MODE REPLY21AN931AC20 AKNAD 18TYPE,INCLOSURE INCLOSURE TYPE INDICATES THE TYPE OF INCLOSURE PROVIDED TO COAT,COVER,PROTECT,OR ENCASE THE ITEM. SELECT REPLY CODE 10AG85 AKNBD 18TYPE,KNUCKLE KNUCKLE TYPE INDICATES THE TYPE OF CYLINDRICAL PROJECTION THROUGH WHICH AN AXIS OR PIN PASSES. SELECT REPLY CODE 10AG30 AKNCD /D/ 18TYPE,BASE,LAMP LAMP BASE TYPE INDICATES THE TYPE OF LAMP BASE. SELECT REPLY CODE 10AD36 AKNDD /D/ 09MATERIAL,COATING,LINING LINING COATING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE WITH WHICH THE LINING IS COATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AKNED /D/ 08LOCATION,MATERIAL,LINING COATING LINING COATING MATERIAL LOCATION INDICATES THE LOCATION OF THE LINING TO WHICH A COATING HAS BEEN APPLIED. SELECT REPLY CODE 10AE46 AKNFJ 10CAPABILITY,HANDLING,RF POWER RF POWER HANDLING CAPABILITY THE AMOUNT OF RADIO FREQUENCY POWER HANDLING CAPABILITY THAT CAN BE DISSIPATED SAFELY BY AN ITEM. 2D AND 1B MODE REPLY22AB491AF65 AKNGJ /D/ 10FREQUENCY RATING,CAPABILITY,HANDLING,RF POWER RF POWER HANDLING CAPABILITY FREQUENCY RATING THE FREQUENCY RATING AT WHICH THE RADIO FREQUENCY POWER HANDLING CAPABILITY APPLIES. 1D AND 1B MODE REPLY11AC32 AKNHJ /D/T10RANGE,FREQUENCY,RF POWER HANDLING CAPABILITY RF POWER HANDLING CAPABILITY FREQUENCY RANGE THE MINIMUM AND MAXIMUM VALUES OF THE FREQUENCY RANGE AT WHICH THE RADIO FREQUENCY POWER HANDLING CAPABILITY APPLIES. 1D AND 1F MODE REPLY11AC32 AKNJJ 10RESISTANCE,COIL,FIELD FIELD COIL RESISTANCE THE AMOUNT OF OPPOSITION TO THE FLOW OF DIRECT CURRENT OFFERED BY THE FIELD COIL. 1D AND 1B MODE REPLY11AA57 AKNKJ T10RANGE,FREQUENCY,VOLTAGE STANDING WAVE RATIO VOLTAGE STANDING WAVE RATIO FREQUENCY RANGE THE MINIMUM AND MAXIMUM VALUES OF THE FREQUENCY RANGE IN WHICH THE VOLTAGE STANDING WAVE RATIO IS SPECIFIED. 1D AND 1F MODE REPLY11AC32 AKNLJ /D/ 10FREQUENCY,RATIO,VOLTAGE STANDING WAVE VOLTAGE STANDING WAVE RATIO FREQUENCY THE FREQUENCY AT WHICH THE VOLTAGE STANDING WAVE RATIO IS RATED. 1D AND 1B MODE REPLY11AC32 AKNMD /D/ 18TYPE,ELEMENT,TRANSDUCER TRANSDUCER ELEMENT TYPE INDICATES THE TYPE OF TRANSDUCER ELEMENT. SELECT REPLY CODE 10AG88 AKNND /D/ 09MATERIAL,CONE CONE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CONE IS FABRICATED. SELECT REPLY CODE 10AD09 AKNPJ /D/ 10FREQUENCY,REFERENCE,INSERTION LOSS INSERTION LOSS REFERENCE FREQUENCY THE REFERENCE FREQUENCY AT WHICH THE INSERTION LOSS IS RATED. 1D AND 1B MODE REPLY11AC32 AKNQJ 04DIAMETER,TRANSDUCER TRANSDUCER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR TRANSDUCER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKNRJ 04LENGTH,TRANSDUCER TRANSDUCER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TRANSDUCER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AKNSJ 04WIDTH,TRANSDUCER TRANSDUCER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TRANSDUCER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AKNTJ /D/T10RANGE,FREQUENCY,INSERTION LOSS INSERTION LOSS FREQUENCY RANGE THE MINIMUM AND MAXIMUM VALUES OF THE FREQUENCY RANGE IN WHICH THE INSERTION LOSS IS RATED. 1D AND 1F MODE REPLY11AC32 AKNUJ 10LOAD RATING,STATIC,DEFLECTION AT DEFLECTION AT STATIC LOAD RATING THE COMPRESSION OF AN ITEM WHEN A DEFINED FORCE IS APPLIED ALONG THE DIRECTION OF THE APPLIED FORCE. 2D AND 1B MODE REPLY21AA051AC20 AKNVB 10CROSSTALK RATING IN DECIBELS,MINIMUM MINIMUM CROSSTALK RATING IN DECIBELS THE MINIMUM AMOUNT OF ISOLATION THE ITEM OFFERS AGAINST INTERFERENCE FROM ADJACENT CHANNEL OPERATION,EXPRESSED IN DECIBELS. 1B MODE REPLY 0 AKNWJ /D/ 10FREQUENCY,REFERENCE,CROSSTALK CROSSTALK REFERENCE FREQUENCY THE REFERENCE FREQUENCY AT WHICH THE CROSSTALK IS RATED. 1D AND 1B MODE REPLY11AC32 AKNXD 19FACILITY,MOUNTING,HORN HORN MOUNTING FACILITY THE MEANS PROVIDED FOR ATTACHING THE HORN TO THE ITEM. SELECT REPLY CODE 10AM39 AKNYA 12QUANTITY,FACILITY,HORN MOUNTING HORN MOUNTING FACILITY QUANTITY THE NUMBER OF MOUNTING FACILITIES USED AS A MEANS OF ATTACHING THE HORN TO THE ITEM. 1A MODE REPLY 0 AKNZJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,FACILITY,HORN MOUNTING HORN MOUNTING FACILITY THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND THE NUMBER OF THREADS PER MEASUREMENT SCALE OF THE HORN MOUNTING FACILITY. 1D AND 1A MODE REPLY12AH06 AKPAJ /D/T10RANGE,FREQUENCY,CROSSTALK CROSSTALK FREQUENCY RANGE THE MINIMUM AND MAXIMUM VALUES OF THE FREQUENCY RANGE IN WHICH THE CROSSTALK RATING IS SPECIFIED. 1D AND 1F MODE REPLY11AC32 AKPBJ 04DIAMETER,COIL,VOICE VOICE COIL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A VOICE COIL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKPCD 11METHOD,OPERATING,ACTUATOR ACTUATOR OPERATING METHOD THE MEANS PROVIDED FOR SWITCHING THE ACTUATOR FROM ONE POSITION TO ANOTHER. SELECT REPLY CODE 10AA77 AKPDJ 10IMPEDANCE RATING IN OHMS,PRIMARY,TRANSFORMER TRANSFORMER PRIMARY IMPEDANCE RATING IN OHMS THE TOTAL OPPOSITION /RESISTIVE AND REACTIVE/ WHICH THE TRANSFORMER PRIMARY WINDING OFFERS TO THE FLOW OF ALTERNATING CURRENT,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 AKPEJ 10CURRENT TYPE AND RATING IN AMPS,ACTUATOR ACTUATOR CURRENT TYPE AND RATING IN AMPS THE ACTUATOR CURRENT TYPE AND AMOUNT OF ELECTRON FLOW AT WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN AMPERES. 2D AND 1B MODE REPLY21AB621AC20 AKPFD /D/ 19FACILITY,MOUNTING,TRANSFORMER TRANSFORMER MOUNTING FACILITY THE MEANS PROVIDED FOR ATTACHING THE TRANSFORMER TO AN ITEM. SELECT REPLY CODE 10AB89 AKPGA /D/ 12QUANTITY,FACILITY,TRANSFORMER MOUNTING TRANSFORMER MOUNTING FACILITY QUANTITY THE NUMBER OF MOUNTING FACILITIES USED AS A MEANS OF ATTACHING THE TRANSFORMER TO AN ITEM. 1A MODE REPLY 0 AKPHJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,FACILITY,TRANSFORMER MOUNTING TRANSFORMER MOUNTING FACILITY THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND THE NUMBER OF THREADS PER MEASUREMENT SCALE OF THE TRANSFORMER MOUNTING FACILITY. 1D AND 1A MODE REPLY12AC21 AKPJJ 10VOLTAGE IN VOLTS,ACTUATOR ACTUATOR VOLTAGE IN VOLTS THE VALUE/S/,OR RANGE OF VALUES,OF POTENTIAL FOR WHICH THE ITEM IS RATED,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 AKPKJ /D/ 04DIAMETER,HOLE,UNTHREADED MOUNTING,TRANSFORMER TRANSFORMER UNTHREADED MOUNTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TRANSFORMER UNTHREADED MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKPLJ /D/ 04DISTANCE BETWEEN TRANSFORMER MOUNTING FACILITIES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN TRANSFORMER MOUNTING FACILITIES THE CENTER TO CENTER DISTANCE BETWEEN TRANSFORMER MOUNTING FACILITIES. 2D AND 1B MODE REPLY21AA051AC20 AKPMB /D/ 10VOLTAGE IN VOLTS,DROPOUT,ACTUATOR ACTUATOR DROPOUT VOLTAGE IN VOLTS THE VOLTAGE RATING AT WHICH THE ITEM WILL RELEASE TO ITS DE-ENERGIZED POSITION,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AKPND 19SEQUENCE,OPERATION,SWITCH SWITCH OPERATION SEQUENCE AN INDICATION OF WHETHER THE LOBE OF THE ROTATING CAM IS DESIGNED TO ACTUATE /MAKE/ A SWITCH BEFORE OR AFTER THE PRECEDING SWITCH DEACTUATES /BREAKS/. SELECT REPLY CODE 10AD78 AKPPJ 10TIME,SWITCHING SWITCHING TIME THE TIME REQUIRED FOR SWITCHING BETWEEN ANY TWO ADJACENT POSITIONS. 1D AND 1B MODE REPLY12AB49 AKPQD 18TYPE,MECHANISM,SWITCH RETURN SWITCH RETURN MECHANISM TYPE THE OPERATION OF THE SWITCH MECHANISM WHEN THE SWITCH RETURN ACTUATOR POWER IS REMOVED. SELECT REPLY CODE 10AG90 AKPRD /D/ 11METHOD,TERMINATION,OFF CIRCUIT OFF CIRCUIT TERMINATION METHOD THE MEANS EMPLOYED TO TERMINATE THE OFF CIRCUIT OUTPUT TERMINALS. SELECT REPLY CODE 10AG91 AKPSD 19CYCLE,DUTY DUTY CYCLE THE WORKING PERIOD UNDER WHICH THE ITEM WAS DESIGNED TO OPERATE. SELECT REPLY CODE 10AD63 AKPTD 18TYPE,FLANGE,WAVEGUIDE WAVEGUIDE FLANGE TYPE INDICATES THE TYPE OF WAVEGUIDE FLANGE. SELECT REPLY CODE 10AG92 AKPUJ 10LOAD CAPACITY,RATED FREQUENCY RATED FREQUENCY LOAD CAPACITY THE WEIGHT THAT IS APPLIED TO AN ITEM TO DETERMINE THE ABILITY TO CARRY THAT WEIGHT WHILE BEING VIBRATED WITHOUT DAMAGING THE ITEM. 2D AND 1B MODE REPLY21AN931AA05 AKPVA 12QUANTITY,FACILITY,MOUNTING MOUNTING FACILITY QUANTITY THE NUMBER OF MOUNTING FACILITIES PROVIDED. 1A MODE REPLY 0 AKPWJ /D/ 04LENGTH,FACILITY,THREADED MOUNTING THREADED MOUNTING FACILITY LENGTH A MEASUREMENT OF THE LONGEST DIMENSION THAT THE THREADED MOUNTING FACILITY PROTRUDES FROM THE MOUNTING SURFACE. 2D AND 1B MODE REPLY21AA051AC20 AKPXA 12QUANTITY,POLE POLE QUANTITY THE NUMBER OF POLES INCLUDED IN THE ITEM. 1A MODE REPLY 0 AKPYA 12QUANTITY,THROW THROW QUANTITY THE NUMBER OF POSITIONS TO WHICH THE ITEM MAY BE ACTUATED TO ENERGIZE ELECTRICAL CIRCUITS. 1A MODE REPLY 0 AKPZD 18TYPE,MATERIAL,INCLOSURE INCLOSURE MATERIAL TYPE INDICATES THE TYPE OF MATERIAL USED TO INCLOSE THE ITEM. SELECT REPLY CODE 10AD93 AKQAJ 10VOLTAGE RATING,MAXIMUM,RF RF MAXIMUM VOLTAGE RATING THE MAXIMUM RADIO FREQUENCY VOLTAGE THAT THE INSULATING MATERIALS OF THE ITEM WILL WITHSTAND WITHOUT RESULTING IN DISRUPTIVE DISCHARGE OR DETERIORATION. 2D AND 1B MODE REPLY21AB631AF65 AKQBH /D/ 19FEATURE AND LOCATION,LUBRICATION LUBRICATION FEATURE AND LOCATION THE TYPE OF LUBRICATION FEATURE,INHERENT IN THE ITEM DESIGN TO EFFECT LUBRICATION,AND ITS LOCATION. 2D MODE REPLY 21AB992AE46 AKQCJ /D/ 04LENGTH,CHAMFER,OUTSIDE CORNER,FIRST FIRST OUTSIDE CORNER CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 AKQDJ /D/ 04LENGTH,CHAMFER,OUTSIDE CORNER,SECOND SECOND OUTSIDE CORNER CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 AKQEJ /D/ 04LENGTH,CHAMFER,OUTSIDE CORNER,FOURTH FOURTH OUTSIDE CORNER CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 AKQFJ /D/ 04LENGTH,CHAMFER,INSIDE CORNER,SECOND SECOND INSIDE CORNER CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 AKQGJ /D/ 04LENGTH,CHAMFER,INSIDE CORNER,THIRD THIRD INSIDE CORNER CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 AKQHJ /D/ 04LENGTH,CHAMFER,INSIDE CORNER,FOURTH FOURTH INSIDE CORNER CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 AKQJJ 04DISTANCE BETWEEN BRACKET MOUNTING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN BRACKET MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AKQKJ 04DIAMETER,HOLE,MOUNTING,BRACKET BRACKET MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AKQLB 10TRANSMITTANCE IN PERCENT,LIGHT,TINTED AREA TINTED AREA LIGHT TRANSMITTANCE IN PERCENT THE PERCENT OF INFRARED AND ULTRAVIOLET RAYS CONTAINED IN LIGHT THAT PASSES THROUGH THE TINTED AREA OF THE ITEM. 1B MODE REPLY 0 AKQMJ /D/ 10POWER RATING IN DIOPTERS,ADDITIONAL ADDITIONAL POWER RATING IN DIOPTERS A SECTION AND/OR SECTIONS OF OPHTHALMIC GLASS WITH A HIGHER INDEX OF REFRACTION WHICH HAS BEEN ADDED TO THE MAJOR LENS,EXPRESSED IN DIOPTERS. 1D AND 1B MODE REPLY12AE46 AKQNJ 10FREQUENCY AT LOAD FREQUENCY AT LOAD THE VIBRATION, IN CYCLES PER SECOND (HERTZ), THAT IS USED ON AN ITEM TO DETERMINE THE ABILITY OF THE ITEM TO ABSORB FORCE WITHOUT DAMAGE. 2D AND 1B MODE REPLY21AC321AA05 AKQPB 10CURVE IN DIOPTERS,BASE BASE CURVE IN DIOPTERS THE CURVATURE FOR GRINDING A LENS TO THE DESIRED MERIDIAN OF LEAST REFRACTION,EXPRESSED IN DIOPTERS. 1B MODE REPLY 0 AKQQB 10CURVE IN DIOPTERS,CROSS CROSS CURVE IN DIOPTERS THE CURVATURE FOR GRINDING A LENS TO THE DESIRED MERIDIAN OF GREATEST REFRACTION,EXPRESSED IN DIOPTERS. 1B MODE REPLY 0 AKQRD /D/ 09MATERIAL,PAD,POLISHING POLISHING PAD MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE POLISHING PAD IS FABRICATED. SELECT REPLY CODE 10AD09 AKQSD /D/ 07COATING,PRESERVATIVE PRESERVATIVE COATING AN INDICATION OF WHETHER OR NOT A COATING APPLIED TO THE SURFACE TO HELP RETARD CORROSION DURING STORAGE IS INCLUDED. SELECT REPLY CODE 10AA49 AKQTD /D/ 19PACKAGING,SPECIAL SPECIAL PACKAGING AN INDICATION OF SPECIAL PACKAGING REQUIRED FOR AN ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. SELECT REPLY CODE 10AG93 AKQUD 09MATERIAL FOR WHICH DESIGNED MATERIAL FOR WHICH DESIGNED THE MATERIAL FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10MA01 AKQVJ 04DIAMETER,SEGMENT,READING READING SEGMENT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AKQWJ 04HEIGHT,SEGMENT,READING READING SEGMENT HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AKQXJ /D/ 04WIDTH,SEGMENT,READING READING SEGMENT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKQYJ /D/ 04HEIGHT,SEGMENT,INTERMEDIATE INTERMEDIATE SEGMENT HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AKQZJ 10DIOPTER,CURVE,BASE BASE CURVE DIOPTER A MEASUREMENT OF THE BASE CURVE,EXPRESSED IN DIOPTERS. 2D AND 1B MODE REPLY21AH081AC20 AKRAJ 10DIOPTER,CURVE,CROSS CROSS CURVE DIOPTER A MEASUREMENT OF THE CROSS CURVE,EXPRESSED IN DIOPTERS. 2D AND 1B MODE REPLY21AH081AC20 AKRBJ 10PLANO,CURVE,BASE BASE CURVE PLANO NONE. 2D AND 1B MODE REPLY21AH081AC20 AKRCA 12QUANTITY,POSITION,COUPLING COUPLING POSITION QUANTITY THE NUMBER OF COUPLING POSITIONS PROVIDED. 1A MODE REPLY 0 AKRDA 12QUANTITY,OPENING,CABLE CABLE OPENING QUANTITY THE NUMBER OF OPENINGS DESIGNED TO ACCOMMODATE A CABLE. 1A MODE REPLY 0 AKREJ 10VOLTAGE RATING IN VOLTS VOLTAGE RATING IN VOLTS THE VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AB62 AKRFD 18TYPE,SEAL SEAL TYPE INDICATES THE TYPE OF SEAL INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AG94 AKRGA 12QUANTITY,POINT POINT QUANTITY THE NUMBER OF POINTS PROVIDED. 1A MODE REPLY 0 AKRHJ /D/ 04LENGTH,ROPE ROPE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKRJD /D/ 08LOCATION,INSULATION INSULATION LOCATION INDICATES THE LOCATION OF AN ITEM THAT IS INSULATED. SELECT REPLY CODE 10AA47 AKRKJ /D/ 04DISTANCE FROM CENTERLINE TO POLARIZATION POSITION DISTANCE FROM CENTERLINE TO POLARIZATION POSITION NONE. 2D AND 1B MODE REPLY21AA051AC20 AKRLJ 10OPENING,JAW JAW OPENING A MEASUREMENT OF THE JAW OPENING WITH THE JAWS FULLY OPENED. 2D AND 1B MODE REPLY21AA051AC20 AKRMJ 04DIAMETER,ACCOMMODATION,HOLE HOLE ACCOMMODATION DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOLE ACCOMMODATION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKRNJ 04WIDTH,ACCOMMODATION,SLOT SLOT ACCOMMODATION WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SLOT ACCOMMODATION,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AKRPJ 04LENGTH,ACCOMMODATION,PIN PIN ACCOMMODATION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE PIN ACCOMMODATION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AKRQJ 04DIAMETER,ACCOMMODATION,PIN PIN ACCOMMODATION DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PIN ACCOMMODATION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKRRJ 04DIAMETER,GROOVE,RETENTION RETENTION GROOVE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE RETENTION GROOVE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKRSJ 04LENGTH,PIN PIN LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE PIN,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AKRTJ 04WIDTH,CONTACT,MATING MATING CONTACT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MATING CONTACT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AKRUJ 04DIAMETER OF SAW BLADE,MAXIMUM MAXIMUM DIAMETER OF SAW BLADE THE LARGEST DIAMETER BLADE THAT FITS THE SAW AND WILL OPERATE WITHIN THE BLADE GUARD. 1D AND 1B MODE REPLY11AA05 AKRVJ 04WIDTH,PIN PIN WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PIN,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AKRWJ /D/ 04DISTANCE FROM POLARIZATION CENTERLINE TO REAR OF SHELL DISTANCE FROM POLARIZATION CENTERLINE TO REAR OF SHELL NONE. 2D AND 1B MODE REPLY21AA051AC20 AKRXJ 04LENGTH,WORK WORK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE WORKING AREA OF AN ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AKRYJ 04HEIGHT,POINT POINT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE POINT,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AKRZD 18TYPE,TERMINATION TERMINATION TYPE INDICATES THE TYPE OF FACILITY PROVIDED ON THE DEVICE FOR ATTACHING TO ANOTHER ITEM. SELECT REPLY CODE 10AE79 AKSAA 03DESIGNATION,FLANGE,WAVEGUIDE WAVEGUIDE FLANGE DESIGNATION THE ALPHABETICAL CHARACTERS AND NUMERALS WHICH IDENTIFY THE SPECIFIC WAVEGUIDE FLANGE TYPE. 1A MODE REPLY 0 AKSBJ 04SIZE,NOMINAL,COAXIAL LINE FLANGE COAXIAL LINE FLANGE NOMINAL SIZE THE DESIGNATION OR TERM USED TO DEFINE THE NOMINAL SIZE OF THE COAXIAL LINE FLANGE. 1D AND 1B MODE REPLY11AA05 AKSCD 13THREAD LOCATION,CONNECTION,INTAKE INTAKE CONNECTION THREAD LOCATION THE LOCATION OF THE THREADS ON THE INTAKE CONNECTION. SELECT REPLY CODE 10AJ91 AKSDD 13THREAD LOCATION,CONNECTION,DISCHARGE DISCHARGE CONNECTION THREAD LOCATION THE LOCATION OF THE THREADS ON A DISCHARGE CONNECTION. SELECT REPLY CODE 10AJ91 AKSEB /D/ 04TAPER PER METER IN MILLIMETERS TAPER PER METER IN MILLIMETERS THE DIMINISHING MEASUREMENT OF THE DIAMETER ALONG THE MAJOR AXIS OF THE ITEM,EXPRESSED PER METER IN MILLIMETERS. 1B MODE REPLY 0 AKSFD 18TYPE,CONTACT CONTACT TYPE INDICATES THE TYPE OF CONTACT(S) INCLUDED ON THE ITEM. SELECT REPLY CODE 10AG81 AKSGD /D/ 09MATERIAL,SURFACE,CONTACT POINT CONTACT POINT SURFACE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CONTACT POINT SURFACE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AKSHA 19AGENCY,GOVERNMENT,CONTROLLING CONTROLLING GOVERNMENT AGENCY THE NAME OF THE GOVERNMENT AGENCY CONTROLLING THE ITEM. 1A MODE REPLY 0 AKSJA 19NAME ASSIGNED BY GOVERNMENT AGENCY,ITEM ITEM NAME ASSIGNED BY GOVERNMENT AGENCY THE NAME OF THE ITEM AS ASSIGNED BY THE CONTROLLING GOVERNMENT AGENCY. 1A MODE REPLY 0 AKSKA /D/ 19NUMBER ASSIGNED BY GOVERNMENT AGENCY,IDENTIFYING,ITEM ITEM IDENTIFYING NUMBER ASSIGNED BY GOVERNMENT AGENCY AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY CONTROLLING THE ITEM. 1A MODE REPLY 0 AKSLD 19PURPOSE FOR WHICH DESIGNED PURPOSE FOR WHICH DESIGNED THE PURPOSE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AG95 AKSMD /D/ 09MATERIAL,JACKET,TUBING TUBING JACKET MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TUBING JACKET IS FABRICATED. SELECT REPLY CODE 10AD09 AKSNB /D/ 04ANGLE IN DEG,OFFSET,SECOND LEG SECOND LEG OFFSET ANGLE IN DEG NONE. 1B MODE REPLY 0 AKSPB /D/ 04ANGLE IN DEG,OFFSET,FIRST LEG FIRST LEG OFFSET ANGLE IN DEG NONE. 1B MODE REPLY 0 AKSQD /D/ 07TREATMENT,RESISTANT,FUNGUS FUNGUS RESISTANT TREATMENT AN INDICATION OF WHETHER OR NOT A TREATMENT IS INCLUDED TO PRODUCE A FUNGUS RESISTANT CONDITION. SELECT REPLY CODE 10AA49 AKSRA 19NUMBER,SERIES,STANDARD SIEVE STANDARD SIEVE SERIES NUMBER A DESIGNATION OF THE STANDARD SIEVE USED TO SIZE PARTICLES OF MATERIAL. 1A MODE REPLY 0 AKSSD /D/ 07FEATURE,WATERPROOF WATERPROOF FEATURE AN INDICATION OF WHETHER OR NOT A WATERPROOF FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AKSTA /D/ 08LOCATION,ATTACHMENT ATTACHMENT LOCATION INDICATES THE LOCATION OF THE ATTACHMENT ON THE ITEM. 1A MODE REPLY 0 AKSUG /D/ 07RENGE,CUTTING CAPACITY,USS GAGE SHEET STEEL USS GAGE SHEET STEEL CUTTING CAPACITY RENGE THE RANGE OF THICKNESS GAGE NUMBERS OF UNITED STATES SHEET STEEL THAT THE ITEM CAN CUT. FULL TEXT WRITE-IN 0 AKSVJ 04DIAMETER,PERFORATION PERFORATION DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OPENING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKSWJ 12QUANTITY,PERFORATION PERFORATION QUANTITY A NUMERIC VALUE WHICH REPRESENTS THE NUMBER OF PERFORATIONS CONTAINED IN THE ITEM. 1D AND 1B MODE REPLY11AB39 AKSXB 04SIZE,MESH MESH SIZE A NUMERIC VALUE WHICH REPRESENTS THE NUMBER OF OPENINGS PER LINEAL INCH. 1B MODE REPLY 0 AKSYJ /D/ 04LENGTH FROM FLANGE TO END,SECOND END SECOND END LENGTH FROM FLANGE TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AKSZJ /D/ 04LENGTH FROM FLANGE TO END,FIRST END FIRST END LENGTH FROM FLANGE TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AKTAJ /D/ 04DIAMETER,INSIDE,FIRST END FLANGE FIRST END FLANGE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AKTBJ /D/ 04DIAMETER,INSIDE,SECOND END FLANGE SECOND END FLANGE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AKTCJ /D/ 04DIAMETER,STEP,FIRST END FLANGE FIRST END FLANGE STEP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AKTDJ /D/ 04DIAMETER,STEP,SECOND END FLANGE SECOND END FLANGE STEP DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SECOND END FLANGE STEP, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKTEJ /D/ 04DISTANCE FROM FLANGE STEP TO END,FIRST END FIRST END DISTANCE FROM FLANGE STEP TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AKTFJ /D/ 04DISTANCE FROM FLANGE STEP TO END,SECOND END SECOND END DISTANCE FROM FLANGE STEP TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AKTGD /D/ 18TYPE,EDGE EDGE TYPE INDICATES THE TYPE OF EDGE CONFIGURATION OF THE ITEM. PLEASE USE MRC AQQR IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD07 AKTHJ /D/ 04DIAMETER,OUTSIDE,FIRST END COLLAR FIRST END COLLAR OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AKTJJ /D/ 04DIAMETER,OUTSIDE,SECOND END COLLAR SECOND END COLLAR OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AKTKJ /D/ 04LENGTH,SLOT,FIRST END FIRST END SLOT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKTLJ /D/ 04LENGTH,SLOT,SECOND END SECOND END SLOT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKTMJ 04WIDTH,SLOT,FIRST END FIRST END SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKTNJ 04WIDTH,SLOT,SECOND END SECOND END SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKTPA /D/ 12QUANTITY,SLOT,FIRST END FIRST END SLOT QUANTITY NONE. 1A MODE REPLY 0 AKTQA /D/ 12QUANTITY,SLOT,SECOND END SECOND END SLOT QUANTITY NONE. 1A MODE REPLY 0 AKTRJ 10TEMP AT MAXIMUM OPERATING PRESSURE TEMP AT MAXIMUM OPERATING PRESSURE THE TEMPERATURE OF THE ITEM AT MAXIMUM OPERATING PRESSURE. 1D AND 1B MODE REPLY11AB36 AKTSJ /D/ 04DISTANCE FROM CENTER OF BOLT HOLE TO END,FIRST END FIRST END DISTANCE FROM CENTER OF BOLT HOLE TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AKTTJ /D/ 04DISTANCE FROM CENTER OF BOLT HOLE TO END,SECOND END SECOND END DISTANCE FROM CENTER OF BOLT HOLE TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AKTUD 01COLOR,SHEATH SHEATH COLOR THE HUE OR TINT OF THE SHEATH. SELECT REPLY CODE 10AD06 AKTVJ /D/ 04DIAMETER,OUTSIDE,FIRST END UNDERCUT FIRST END UNDERCUT OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AKTWJ /D/ 04DIAMETER,OUTSIDE,SECOND END UNDERCUT SECOND END UNDERCUT OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AKTXJ 04DIAMETER,COUNTERBORE,FIRST END FIRST END COUNTERBORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AKTYJ 04DIAMETER,COUNTERBORE,SECOND END SECOND END COUNTERBORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AKTZJ 04DEPTH,COUNTERBORE,FIRST END FIRST END COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKUAA 12QUANTITY,IMPLEMENT IMPLEMENT QUANTITY THE NUMBER OF IMPLEMENTS INCLUDED WITH THE ITEM. 1A MODE REPLY 0 AKUBJ 04LENGTH,OPEN OPEN LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM WHEN OPENED, IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AKUCJ /D/A04DIAMETER,STRIPPING BLADE,MINIMUM MINIMUM STRIPPING BLADE DIAMETER THE MINIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE STRIPPING BLADE AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1A MODE REPLY11AA05 AKUDA 12POSITION QUANTITY,LOCKING,BLADE BLADE LOCKING POSITION QUANTITY THE NUMBER OF BLADE LOCKING POSITIONS INCLUDED ON THE ITEM. 1A MODE REPLY 0 AKUEA 12BLADE QUANTITY,EXTRA EXTRA BLADE QUANTITY THE NUMBER OF EXTRA BLADES INCLUDED WITH THE ITEM. 1A MODE REPLY 0 AKUFA /D/ 03NUMERIC DESIGNATOR,THREAD DIAMETER THREAD DIAMETER NUMERIC DESIGNATOR THE NUMBER ASSIGNED TO DESIGNATE THE DIAMETER OF THE THREAD. 1A MODE REPLY 0 AKUGA 12QUANTITY,CLAW CLAW QUANTITY THE NUMBER OF CLAWS INCLUDED ON THE ITEM. 1A MODE REPLY 0 AKUHD 03AFFILIATION,RELIGIOUS RELIGIOUS AFFILIATION DESIGNATES THE RELIGIOUS AFIFLIATION OF THE ITEM. SELECT REPLY CODE 10RA01 AKUJA /D/ 03NUMBER,BOOK,INTERNATIONAL STANDARD INTERNATIONAL STANDARD BOOK NUMBER THE UNIQUE IDENTIFIER FOR BOOKS, ASSIGNED IN COMPLIANCE WITH ISO 2108. 1A MODE REPLY 0 AKUKD 18PROTECTION PROVISION TYPE,DATA DATA PROTECTION PROVISION TYPE THE TYPE OF DATA PROTECTION THAT IS INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AM04 AKULB 12IMPACT BLOWS PER MINUTE IMPACT BLOWS PER MINUTE THE NUMBER OF IMPACT BLOWS WHICH THE ITEM WILL MAKE WITHIN A SPECIFIC PERIOD OF TIME. 1B MODE REPLY 0 AKUMJ 04NOMINAL THREAD DIAMETER,AIR INLET AIR INLET NOMINAL THREAD DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED AIR INLET, AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AKUNG 13THREAD SIZE,SPINDLE SPINDLE THREAD SIZE DESIGNATES THE SPINDLE THREAD SERIES AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. FULL TEXT WRITE-IN 0 AKUPJ 10CHUCK SIZE,NOMINAL NOMINAL CHUCK SIZE A NOMINAL MEASUREMENT OF THE SIZE OF THE CHUCK. 1D AND 1B MODE REPLY11AA05 AKUQB /D/ 12STROKES PER MINUTE STROKES PER MINUTE THE NUMBER OF STROKES WHICH THE ITEM WILL OPERATE WITHIN A SPECIFIED PERIOD OF TIME. 1B MODE REPLY 0 AKURJ /D/ 12STROKES PER MINUTE STROKES PER MINUTE THE NUMBER OF STROKES WHICH THE ITEM WILL OPERATE WITHIN A SPECIFIED PERIOD OF TIME. 1D AND 1B MODE REPLY11AC20 AKUSJ 04DEPTH CAPACITY,PLUNGE PLUNGE DEPTH CAPACITY THE DEPTH OF WHICH THE BASE WILL PLUNGE. 2D AND 1B MODE REPLY21AA051AC20 AKUTD 02CONSTRUCTION,END FLANGE END FLANGE CONSTRUCTION THE DESIGN USED IN CONSTRUCTING THE END PORTION OF THE FLANGE. SELECT REPLY CODE 10AC40 AKUUD 02DESIGN,END CONNECTION END CONNECTION DESIGN THE PHYSICAL CONFIGURATION OF THE OUTSIDE OF THE END CONNECTION. SELECT REPLY CODE 10AC41 AKUVJ /D/A08LUGS,DISTANCE BETWEEN FIRST END DISTANCE BETWEEN FIRST END LUGS THE DISTANCE BETWEEN THE LUGS ON THE FIRST END OF THE ITEM. 3D AND 1B MODE REPLY31AA051AC202AN68 AKUWJ /D/A12DUTY CYCLE,INK CARTRIDGE INK CARTRIDGE DUTY CYCLE MAXIMUM NUMBER OF PAGES PRINTED BY ITEM 1D AND 1A MODE REPLY13AE04 AKUXJ A12MAXIMUM FUEL RANGE MAXIMUM FUEL RANGE THE MAXIMUM OPERATING RANGE BEFORE REFUELING. 1D AND 1A MODE REPLY11AA34 AKUYA 12CARGO DOOR QUANTITY CARGO DOOR QUANTITY THE NUMBER OF CARGO DOORS PROVIDED. 1A MODE REPLY 0 AKUZJ /D/A10FORDING DEPTH FORDING DEPTH THE MAXIMUM DEPTH OF SUBMERSION ALLOWED IN WATER. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/11/2024. 1D AND 1A MODE REPLY11AA05 AKVAJ 04DEPTH,COUNTERBORE,SECOND END SECOND END COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKVBJ /D/ 04DISTANCE FROM CENTER OF MOUNTING HOLE TO OUTSIDE EDGE ON WIDTH SIDE,FIRST END FIRST END DISTANCE FROM CENTER OF MOUNTING HOLE TO OUTSIDE EDGE ON WIDTH SIDE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKVCJ /D/ 04DISTANCE FROM CENTER OF MOUNTING HOLE TO OUTSIDE EDGE ON WIDTH SIDE,SECOND END SECOND END DISTANCE FROM CENTER OF MOUNTING HOLE TO OUTSIDE EDGE ON WIDTH SIDE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKVDJ /D/ 04DISTANCE FROM CENTER OF MOUNTING HOLE TO OUTSIDE EDGE ON LENGTH SIDE,FIRST END FIRST END DISTANCE FROM CENTER OF MOUNTING HOLE TO OUTSIDE EDGE ON LENGTH SIDE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKVEJ /D/ 04DISTANCE FROM CENTER OF MOUNTING HOLE TO OUTSIDE EDGE ON LENGTH SIDE,SECOND END SECOND END DISTANCE FROM CENTER OF MOUNTING HOLE TO OUTSIDE EDGE ON LENGTH SIDE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKVFJ /D/ 04DISTANCE BETWEEN MOUNTING HOLES,CENTER TO CENTER,FIRST END FIRST END CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AKVGJ /D/ 04DISTANCE BETWEEN MOUNTING HOLES,CENTER TO CENTER,SECOND END SECOND END CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AKVHJ 10PROTECTION RATING,RADIATION RADIATION PROTECTION RATING THE PROTECTION AFFORDED BY THE MATERIAL AS RATED BY THE THICKNESS OF SHEET LEAD EQUIVALENT. 1D AND 1B MODE REPLY11AA05 AKVJJ 04WIDTH,OFFSET OFFSET WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKVKJ 04RADIUS,CORNER,FOURTH FOURTH CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AKVLJ /D/ 04DISTANCE FROM CENTER OF SLOT TO END,FIRST END FIRST END DISTANCE FROM CENTER OF SLOT TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AKVMJ /D/ 04DISTANCE FROM CENTER OF SLOT TO END,SECOND END SECOND END DISTANCE FROM CENTER OF SLOT TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AKVND 19PATTERN,MESH,WIRE WIRE MESH PATTERN WIRE MESH PATTERN IS THE DEFINITE PATTERN OF TWISTED OR WELDED WIRE. SELECT REPLY CODE 10AD07 AKVPD /D/ 07POSITION,ALL STATION ALL STATION POSITION AN INDICATION OF WHETHER OR NOT A SINGLE SELECTOR POSITION FOR CONNECTING ALL STATIONS SIMULTANEOUSLY IS INCLUDED. SELECT REPLY CODE 10AA49 AKVQA 12QUANTITY,STATION STATION QUANTITY THE NUMBER OF STATIONS PROVIDED. 1A MODE REPLY 0 AKVRA 12QUANTITY,TRANSDUCER TRANSDUCER QUANTITY A NUMERIC VALUE WHICH REPRESENTS THE NUMBER OF DEVICES THAT CONVERT ENERGY FROM ONE FORM TO ANOTHER. 1A MODE REPLY 0 AKVSD 18TYPE,TRANSDUCER TRANSDUCER TYPE INDICATES THE TYPE OF DEVICE THAT CONVERTS ENERGY FROM ONE FORM TO ANOTHER. SELECT REPLY CODE 10AG97 AKVTD /D/ 07AMPLIFIER AMPLIFIER AN INDICATION OF WHETHER OR NOT AN AMPLIFIER IS INCLUDED. SELECT REPLY CODE 10AA49 AKVUB 07OPERATING PRESSURE IN PSI OPERATING PRESSURE IN PSI THE REQUIRED OPERATING PRESSURE EXPRESSED IN POUNDS PER SQUARE INCH. 1B MODE REPLY 0 AKVVJ 10CLEARANCE,INTERNAL INTERNAL CLEARANCE THE CLEARANCE BETWEEN THE BEARING RINGS AND THE ROLLING ELEMENTS. 3D AND 1B MODE REPLY31AA051AC201AA28 AKVWJ /D/ 10PRELOAD RATING,BEARING BEARING PRELOAD RATING THE AMOUNT OF INTERNAL LOADING IN A BEARING WHICH IS INDEPENDENT OF ANY EXTERNAL RADIAL AND/OR AXIAL LOAD. 1D AND 1B MODE REPLY12AB16 AKVXD 18TYPE,TRANSMISSION,ELECTRICAL ELECTRICAL TRANSMISSION TYPE INDICATES THE MANNER IN WHICH THE ELECTRICAL ENERGY IS TRANSMITTED. SELECT REPLY CODE 10AG98 AKVYG 19AGENCY,CONTROLLING,ACCESSORY ACCESSORY CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION THAT CONTROLS THE MANUFACTURE OF THE ACCESSORY ITEM. REINSTATED ON 8/29/16 FULL TEXT WRITE-IN 0 AKVZJ A19NUMBER,IDENTIFYING,ACCESSORY ACCESSORY IDENTIFYING NUMBER THE SPECIFIC NUMBER USED TO IDENTIFY THE ACCESSORY. 1D AND 1A MODE REPLY12AG99 AKWAG /D/ 19NAME,ITEM,JOINT ELECTRONICS TYPE DESIGNATION SYSTEM JOINT ELECTRONICS TYPE DESIGNATION SYSTEM ITEM NAME THE NAME ASSIGNED TO THE ITEM BY THE JOINT ELECTRONICS TYPE DESIGNATION SYSTEM.USE MRC AKSJ AND RELATIONSHIP TO MRC AMSB FULL TEXT WRITE-IN 0 AKWBG /D/ 19NUMBER,TYPE,JOINT ELECTRONICS TYPE DESIGNATION SYSTEM ITEM JOINT ELECTRONICS TYPE DESIGNATION SYSTEM ITEM TYPE NUMBER THE TYPE NUMBER ASSIGNED TO THE ITEM BY THE JOINT ELECTRONICS TYPE DESIGNATION SYSTEM. USE MRC AMSB FULL TEXT WRITE-IN 0 AKWCD 19RELATIONSHIP,SOURCE,ELECTRICAL POWER ELECTRICAL POWER SOURCE RELATIONSHIP THE RELATIONSHIP OF THE ELECTRICAL POWER SOURCE TO THE ITEM. SELECT REPLY CODE 10AH00 AKWDG /D/ 19SIGNAL,OUTPUT OUTPUT SIGNAL THE SIGNAL ENERGY DELIVERED BY AN ITEM. FULL TEXT WRITE-IN 0 AKWED 19CONDITION,SURFACE,FACE SEATING FACE SEATING SURFACE CONDITION THE CONDITION OF THE FACE SEATING SURFACE OF AN ITEM WHICH CONTACTS ANOTHER SURFACE. SELECT REPLY CODE 10AA41 AKWFD 03DESIGNATION,CONTACT,MISSING MISSING CONTACT DESIGNATION THE POSITION IDENTIFICATION OF MISSING CONTACT/S/. SELECT REPLY CODE 10AD83 AKWGD /D/ 18TYPE FOR WHICH DESIGNED,MOUNTING MOUNTING TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF MOUNTING FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AB89 AKWHD 18TYPE,CHARGER CHARGER TYPE INDICATES THE TYPE OF CHARGER FURNISHED. SELECT REPLY CODE 10AG13 AKWJL 16STYLE,ARRANGEMENT,HOLE,PRINTED CIRCUIT BOARD PRINTED CIRCUIT BOARD HOLE ARRANGEMENT STYLE THE ARRANGEMENT OF HOLES IN A PRINTED CIRCUIT BOARD PROVIDED TO ACCOMMODATE TERMINALS,POLARIZATION PIN,AND/OR CENTER SHIELD. 1L MODE REPLY 0 AKWKD 11METHOD,MOUNTING,COMPONENT SHIELD COMPONENT SHIELD MOUNTING METHOD THE MEANS OF ATTACHING A COMPONENT SHIELD. SELECT REPLY CODE 10AM39 AKWLJ 10VOLTAGE IN VOLTS,CHARGING CHARGING VOLTAGE IN VOLTS THE VOLTAGE THE UNIT IS DESIGNED TO DELIVER,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 AKWMJ 10CURRENT RATING IN AMPS,CHARGING CHARGING CURRENT RATING IN AMPS THE CURRENT OUTPUT RATING WHICH THE ITEM DELIVERS,EXPRESSED IN AMPERES. 1D AND 1B MODE REPLY11AC20 AKWND 18TYPE,POLARIZATION POLARIZATION TYPE INDICATES THE TYPE OF POLARIZATION USED TO PREVENT MISMATING. SELECT REPLY CODE 10AH01 AKWPD 11METHOD,REGULATION,CHARGING CHARGING REGULATION METHOD THE MEANS PROVIDED FOR CONTROLLING THE CURRENT OUTPUT. SELECT REPLY CODE 10AD63 AKWQD /D/ 07SHIELD,CENTER CENTER SHIELD AN INDICATION OF WHETHER OR NOT A METALLIC BARRIER IS PROVIDED. SELECT REPLY CODE 10AB22 AKWRD /D/ 07DEVICE,RETAINING,COMPONENT COMPONENT RETAINING DEVICE AN INDICATION OF WHETHER OR NOT A MEANS IS PROVIDED FOR RETAINING A COMPONENT. SELECT REPLY CODE 10AB22 AKWSD /D/ 08LOCATION,RESISTOR RESISTOR LOCATION INDICATES THE LOCATION OF THE RESISTOR(S) ON THE ITEM. SELECT REPLY CODE 10AD83 AKWTA 12QUANTITY,CAPACITOR CAPACITOR QUANTITY THE NUMBER OF CAPACITORS INCLUDED WITH THE ITEM. 1A MODE REPLY 0 AKWUJ 10JAW CAPACITY JAW CAPACITY THE JAW CAPACITY OF AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 AKWVD 08LOCATION,CAPACITOR CAPACITOR LOCATION INDICATES THE LOCATION OF THE CAPACITOR(S) ON THE ITEM. SELECT REPLY CODE 10AD83 AKWWD /D/ 09MATERIAL,SADDLE SADDLE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SADDLE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AKWXD /D/ 17SURFACE TREATMENT,SADDLE SADDLE SURFACE TREATMENT THE PLATING,DIP,AND/OR COATING APPLIED TO THE SADDLE FOR ENVIRONMENTAL PROTECTION OR TO INCREASE FUNCTIONAL EFFICIENCY. SELECT REPLY CODE 10AD09 AKWYD /D/ 09MATERIAL,SHIELD,BASE BASE SHIELD MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHIELD BASE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AKWZD /D/ 17SURFACE TREATMENT,SHIELD,BASE BASE SHIELD SURFACE TREATMENT THE PLATING,DIP,AND/OR COATING APPLIED TO THE SHIELD BASE FOR ENVIRONMENTAL PROTECTION OR TO INCREASE FUNCTIONAL EFFICIENCY. SELECT REPLY CODE 10AD09 AKXAD /D/ 09MATERIAL,SHIELD,CENTER CENTER SHIELD MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CENTER SHIELD IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AKXBD /D/ 17SURFACE TREATMENT,SHIELD,CENTER CENTER SHIELD SURFACE TREATMENT THE PLATING,DIP,AND/OR COATING APPLIED TO THE CENTER SHIELD FOR ENVIRONMENTAL PROTECTION OR TO INCREASE FUNCTIONAL EFFICIENCY. SELECT REPLY CODE 10AD09 AKXCJ 04LENGTH BELOW MOUNTING SURFACE,PROJECTION PROJECTION LENGTH BELOW MOUNTING SURFACE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKXDJ 04LENGTH ABOVE MOUNTING SURFACE,PROJECTION PROJECTION LENGTH ABOVE MOUNTING SURFACE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKXEJ 04DISTANCE FROM FLATTED PORTION TO OPPOSITE SURFACE DISTANCE FROM FLATTED PORTION TO OPPOSITE SURFACE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKXFJ /D/ 04LENGTH,NOTCH,TERMINAL TERMINAL NOTCH LENGTH NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 AKXGJ /D/ 04WIDTH,NOTCH,TERMINAL TERMINAL NOTCH WIDTH NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 AKXHJ /D/ 04LENGTH,NOTCH,LOCATING LOCATING NOTCH LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKXJJ /D/ 04WIDTH,NOTCH,LOCATING LOCATING NOTCH WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKXKG 10CABLE/WIRE SIZE ACCOMMODATED CABLE/WIRE SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE CABLE OR WIRE ACCOMMODATED. FULL TEXT WRITE-IN 0 AKXLH 09END FITTING COMPONENT AND MATERIAL END FITTING COMPONENT AND MATERIAL THE NAME OF THE FITTING AND/OR COMPONENT AND THE ELEMENT, COMPOUND, OR MIXTURE OF WHICH IT IS FABRICATED. 2D MODE REPLY 22AC426MA01 AKXMH 17FITTING COMPONENT AND SURFACE TREATMENT FITTING COMPONENT AND SURFACE TREATMENT THE NAME OF THE FITTING AND/OR COMPONENT AND THE PLATING, DIP AND/OR COATINGTHAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE, ELECTROCHEMICAL OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE. 2D MODE REPLY 22AC426SF01 AKXNJ 04LUBRICITY AT 60 DEG CENTIGRADE LUBRICITY AT 60 DEG CENTIGRADE ABILITY OF A FLUID TO AFFECT FRICTION BETWEEN, AND WEAR IN, SURFACES IN RELAMOTION UNDER LOAD, AS MEASURED BY WEAR SCAR DIAMETER 2D AND 1B MODE REPLY21AA051AC20 AKXPD 07LEAF TAP CONTACT POINT TYPE LEAF TAP CONTACT POINT TYPE INDICATES THE TYPE OF LEAF TAP CONTACT POINT(S) PROVIDED. SELECT REPLY CODE 10AK54 AKXQJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CONNECTION,ROD ROD CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE FOR THE ROD CONNECTION. 1D AND 1A MODE REPLY12AH06 AKXRA /D/ 13THREAD CLASS,CONNECTION,ROD ROD CONNECTION THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE,AND AN EXTERNAL OR INTERNAL THREAD ON THE ROD CONNECTION. 1A MODE REPLY 0 AKXSJ /D/T13THREAD PITCH DIAMETERS,CONNECTION,ROD ROD CONNECTION THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD ON THE ROD CONNECTION. 1D AND 1F MODE REPLY11AA05 AKXTD 13THREAD DIRECTION,CONNECTION,ROD ROD CONNECTION THREAD DIRECTION THE DIRECTION OF THE ROD CONNECTION THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. SELECT REPLY CODE 10AA38 AKXUD 07FLAT LEAF CONTACT POINT TYPE FLAT LEAF CONTACT POINT TYPE INDICATES THE TYPE OF FLAT LEAF CONTACT POINT(S) PROVIDED. SELECT REPLY CODE 10AK54 AKXVJ /D/A13SCREW THREAD SIZE AND SERIES/TYPE DESIGNATOR AND LOCATION,ATTACHMENT ATTACHMENT SCREW THREAD SIZE AND SERIES/TYPE DESIGNATOR AND LOCATION DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE FOR THE ATTACHMENT SCREW AND ITS LOCATION. 2D AND 1A MODE REPLY22AH062AE46 AKXWJ 13THREAD LENGTH,CONNECTION,ROD ROD CONNECTION THREAD LENGTH A MEASUREMENT OF THE EXTENT OF COMPLETE /FULL/ THREADS ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS ON THE ROD CONNECTION.MRC DISCONTINUED FOR GENERALUSE, MRC MAINTAINED FOR DTRA USE ONLY. 2D AND 1B MODE REPLY21AA051AC20 AKXXJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,BODY BODY THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE FOR THE BODY. 1D AND 1A MODE REPLY12AH06 AKXYA /D/ 13THREAD CLASS,BODY BODY THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE,AND AN EXTERNAL OR INTERNAL THREAD ON THE BODY. 1A MODE REPLY 0 AKXZJ /D/T13THREAD PITCH DIAMETER,BODY BODY THREAD PITCH DIAMETER THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD ON THE BODY. 1D AND 1F MODE REPLY11AA05 AKYAD /D/ 13THREAD DIRECTION,BODY BODY THREAD DIRECTION THE DIRECTION OF THE BODY THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 AKYBD 11METHOD,RETENTION,WIRE ROPE WIRE ROPE RETENTION METHOD THE MEANS USED TO HOLD THE WIRE ROPE IN POSITION. SELECT REPLY CODE 10AH04 AKYCJ 04DIAMETER,BORE,ROD CONNECTION ROD CONNECTION BORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A ROD CONNECTION BORE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKYDG 19COMPONENTS AND QUANTITY,ACCESSORY ACCESSORY COMPONENTS AND QUANTITY THE NAME AND NUMBER OF PARTS SUPPLIED WITH THE ITEM WHICH MAY BE REQUIRED FOR APPLICATION. FULL TEXT WRITE-IN 0 AKYEJ 04DIAMETER,HOLE,SECURING PIN SECURING PIN HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SECURING PIN HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKYFJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,PIN HOLE,SECURING SECURING PIN HOLE THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SECURING PIN HOLE. 1D AND 1A MODE REPLY12AH06 AKYGJ 04DEPTH,BORE,ROD CONNECTION ROD CONNECTION BORE DEPTH THE DISTANCE MEASURED ALONG A STRAIGHT LINE PARALLEL TO THE LONGITUDINAL AXIS WHICH ESTABLISHES THE ACCEPTABLE DEPTH OF THE ROD CONNECTION BORE. 2D AND 1B MODE REPLY21AA051AC20 AKYHJ 04DISTANCE FROM CENTER OF SECURING PIN HOLE TO ROD END DISTANCE FROM CENTER OF SECURING PIN HOLE TO ROD END THE DISTANCE ALONG A STRAIGHT LINE FROM THE ROD CONNECTING END AT RIGHT ANGLE TO THE GEOMETRIC AXIS OF THE SECURING PIN HOLE CENTER. 2D AND 1B MODE REPLY21AA051AC20 AKYJJ 04DIAMETER,HOLE,PIVOT PIN PIVOT PIN HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PIVOT PIN HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKYKJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,HOLE,PIVOT PIN PIVOT PIN HOLE THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE FOR A PIVOT PIN HOLE. 1D AND 1A MODE REPLY12AH06 AKYLD /D/ 07FEATURE,BUSHING BUSHING FEATURE AN INDICATION OF WHETHER OR NOT A BUSHING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AKYMD 19REFLECTANCE,SURFACE SURFACE REFLECTANCE THE DEGREE OF BRILLIANCE THAT THE SENSITIZED SURFACE IS DESIGNED TO PRODUCE IN RELATION TO THE PRINT REFLECTION SCALE. SELECT REPLY CODE 10AB46 AKYNG 19ITEMS AND QUANTITY,FURNISHED FURNISHED ITEMS AND QUANTITY THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE. FULL TEXT WRITE-IN 0 AKYPJ 04DIAMETER,ROPE,WIRE,ACCOMMODATED ACCOMMODATED WIRE ROPE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AKYQJ /D/ 04DIAMETER,HOLE,LUG LUG HOLE DIAMETER PLEASE USE MRC BZTQ IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 AKYRJ 04DIAMETER,OUTSIDE,UNTHREADED END UNTHREADED END OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AKYSJ 04DIAMETER,INSIDE,UNTHREADED END UNTHREADED END INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AKYTJ 04DEPTH,UNTHREADED END UNTHREADED END DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKYUD /D/ 19BALLISTIC PROTECTION LEVEL BALLISTIC PROTECTION LEVEL BALLISTIC PROTECTION LEVEL GUARANTEED BY THE ITEM, IN LINE WITH NIJ STANDARDS 0108.01 AND 0101.04 AND NATO STANDARDS (STANAG 2920 AND US MIL-STD-662F). SELECT REPLY CODE 10AE38 AKYVJ 04DISTANCE FROM PIVOT PINHOLE CENTER TO ROD CONNECTION END DISTANCE FROM PIVOT PINHOLE CENTER TO ROD CONNECTION END NONE. 2D AND 1B MODE REPLY21AA051AC20 AKYWJ 04THICKNESS,ARM,FORK FORK ARM THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AKYXJ 04DEPTH,FORK FORK DEPTH THE MEASUREMENT BETWEEN SPECIFIED POINTS OF THE FORK,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AKYYJ 04DIAMETER,SHOULDER,SHANK SHANK SHOULDER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SHANK SHOULDER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AKYZJ 04LENGTH,SHOULDER,SHANK SHANK SHOULDER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SHANK SHOULDER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AKZAJ 04DISTANCE FROM FORK CENTERLINE TO ROD CONNECTION HOLE CENTERLINE DISTANCE FROM FORK CENTERLINE TO ROD CONNECTION HOLE CENTERLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKZBJ 04DISTANCE FROM PIVOT PINHOLE CENTER TO FORK END DISTANCE FROM PIVOT PINHOLE CENTER TO FORK END NONE. 2D AND 1B MODE REPLY21AA051AC20 AKZCJ 04DISTANCE BETWEEN FIRST AND SECOND HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FIRST AND SECOND HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AKZDJ 04DISTANCE BETWEEN SECOND AND THIRD HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SECOND AND THIRD HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AKZEJ 04LENGTH,END,ROD CONNECTION ROD CONNECTION END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AKZFJ 04DISTANCE FROM PIVOT PINHOLE CENTER TO TONGUE END DISTANCE FROM PIVOT PINHOLE CENTER TO TONGUE END NONE. 2D AND 1B MODE REPLY21AA051AC20 AKZGJ 04DISTANCE,TAKE-UP TAKE-UP DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AKZHL 16STYLE,END,CUTTING CUTTING END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CUTTING END. 1L MODE REPLY 0 AKZJL /D/ 16STYLE,SHANK SHANK STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SHANK. 1L MODE REPLY 0 AKZKJ A03DESIGNATOR,SIZE,TAPER SHANK TAPER SHANK SIZE DESIGNATOR THE COMMERCIAL SIZE DESIGNATION OF THE TAPER SHANK. 1D AND 1A MODE REPLY12AH09 AKZLJ 04DIAMETER,CUTTING,NOMINAL NOMINAL CUTTING DIAMETER A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE CUTTING SIZE. 1D AND 1B MODE REPLY11AA05 AKZMJ T04DIAMETER RANGE,CUTTING CUTTING DIAMETER RANGE THE DIMENSIONAL CUTTING LIMITS PROVIDED BY THE ITEM. 1D AND 1F MODE REPLY11AA05 AKZND /D/ 19PILOT FOR WHICH DESIGNED PILOT FOR WHICH DESIGNED AN INDICATION OF THE PILOT DESIGNED TO BE USED WITH THE ITEM. SELECT REPLY CODE 10AB47 AKZPD /D/ 07PILOT,REPLACEABLE REPLACEABLE PILOT AN INDICATION OF WHETHER OR NOT A REPLACEABLE PILOT IS FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AA55 AKZQJ 04DIAMETER,NOMINAL,PILOT HOLE PILOT HOLE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PILOT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AKZRD /D/ 07TIP,CARBIDE CARBIDE TIP AN INDICATION OF WHETHER OR NOT A CARBIDE TIP IS INCLUDED ON THE ITEM. SELECT REPLY CODE 10AA49 AKZSD 19TRANSMISSION,LIGHT LIGHT TRANSMISSION AN INDICATION OF THE LIGHT TRANSMITTANCE CHARACTER OF THE ITEM. SELECT REPLY CODE 10AH07 AKZTB /D/ 04ANGLE IN DEG,POINT POINT ANGLE IN DEG THE ANGLE TO WHICH THE POINT IS FORMED,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AKZUJ /D/ 19BASELINE BALLISTIC LIMIT BASELINE BALLISTIC LIMIT THE EXPERIMENTALLY DERIVED, STATISTICALLY CALCULATED IMPACT VELOCITY AT WHICH A PROJECTILE IS EXPECTED TO COMPLETELY PENETRATE AN ARMOR COMPONENT (SAMPLE, PANEL OR BALLISTIC PANEL) 50 OF THE TIME (V50). THIS VELOCITY IS ALSO THE VELOCITY AT WHICH A PROJECTILE IS EXPECTED TO BE STOPPED BY THE ARMOR 50 OF THE TIME (V50). 1D AND 1B MODE REPLY12AK00 AKZVD 05DIRECTION,ROTATION,CUTTING CUTTING ROTATION DIRECTION THE DIRECTION IN WHICH THE ITEM IS DESIGNED TO ROTATE IN ORDER TO CUT. SELECT REPLY CODE 10AA38 AKZWJ 04DEPTH,NOMINAL DRILLING NOMINAL DRILLING DEPTH THE NOMINAL DEPTH THE ITEM IS CAPABLE OF DRILLING. 1D AND 1B MODE REPLY11AA05 AKZXG 19HOLDER ACCOMMODATED HOLDER ACCOMMODATED THE SPECIFIC HOLDER WHICH THE ITEM IS DESIGNED TO ACCOMMODATE. FULL TEXT WRITE-IN 0 AKZYJ 04LENGTH,TWIST TWIST LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TWIST,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AKZZB 04ANGLE IN DEG,INCLUDED INCLUDED ANGLE IN DEG THE MEASUREMENT OF THE INCLUDED ANGLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ALAAJ 04LENGTH,FLUTE FLUTE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FLUTE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALABJ 04LENGTH,SECTION,SMALL FLUTED SMALL FLUTED SECTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ALACJ 04LENGTH,TANG TANG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TANG,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALADJ 04LENGTH,FLATS FLATS LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ALAEJ 04DIAMETER,END,LARGE,SHANK SHANK LARGE END DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ALAFJ 04WIDTH,SQUARE,SHANK LARGE END SHANK LARGE END SQUARE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ALAGJ 04DIAMETER,HOLE,RING RING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ALAHJ 04WIDTH,SQUARE,SHANK SMALL END SHANK SMALL END SQUARE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ALAJJ 04WIDTH,SQUARE,SHANK SHANK SQUARE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ALAKJ 04THICKNESS,TANG TANG THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ALALJ 10TAPER PER FOOT TAPER PER FOOT THE AMOUNT OF TAPER,EXPRESSED PER FOOT. 2D AND 1B MODE REPLY21AA051AC20 ALAMJ 04DIAMETER,DRILL DRILL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A DRILL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ALANJ 04LENGTH,DRILL DRILL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ALAPD /D/ 19INDICATOR,FINISH FINISH INDICATOR AN INDICATION OF WHETHER A LAP HAS BEEN FINISHED BY MACHINING TO A SPECIFIC DIOPTER POWER OR SEMIFINISHED BY MACHINING TO AN APPROXIMATE DIOPTER POWER. SELECT REPLY CODE 10AA41 ALAQJ 04RADIUS,CIRCLE,MOUNTING FACILITY MOUNTING FACILITY CIRCLE RADIUS THE RADIUS OF THE CIRCLE IN WHICH THE MOUNTING FACILITIES OF AN ITEM ARE LOCATED. 2D AND 1B MODE REPLY21AA051AC20 ALARA 12QUANTITY,FLUTE FLUTE QUANTITY THE NUMBER OF FLUTES PROVIDED. 1A MODE REPLY 0 ALASD 19CONFIGURATION,INTERNAL INTERNAL CONFIGURATION AN INDICATION OF THE INTERNAL BASIC FORM OF THE ITEM. SELECT REPLY CODE 10AH11 ALATH /D/ 19POLARITY AND CONTROL TYPE,CHANNEL CHANNEL POLARITY AND CONTROL TYPE INDICATES THE POLARITY OF THE CHANNEL /CONDUCTOR MATERIAL/ USED AND CONTROL TYPE. 2D MODE REPLY 22AH122AH13 ALAUF /D/B10CONCENTRATE DOSING RATE IN PERCENT CONCENTRATE DOSING RATE IN PERCENT THE LIMITS OF PERMISSIBLE DOSING VALUES, EXPRESSED IN PERCENT. 1F MODE REPLY 0 ALAVD /D/ 19ARRANGEMENT,MATERIAL,JUNCTION JUNCTION MATERIAL ARRANGEMENT INDICATES THE ARRANGEMENT OF THE MATERIALS OF THE JUNCTION. SELECT REPLY CODE 10AH14 ALAWJ 10VOLTAGE RATING IN VOLTS PER CHARACTERISTIC,MAXIMUM,ABSOLUTE ABSOLUTE MAXIMUM VOLTAGE RATING IN VOLTS PER CHARACTERISTIC THE MAXIMUM LIMITING VALUE OF THE VOLTAGE THAT MAY BE APPLIED AND THE SYMBOL USED TO IDENTIFY THE SPECIFIC ELECTRICAL CHARACTERISTIC,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY12AH15 ALAXB 10BIOBASED CONTENT PERCENTAGE BIOBASED CONTENT PERCENTAGE THE STATED PERCENTAGE OF THE ITEM'S CONTENT THAT IS BIOBASED. 1B MODE REPLY 0 ALAYJ 10CURRENT RATING PER CHARACTERISTIC,MAXIMUM,ABSOLUTE ABSOLUTE MAXIMUM CURRENT RATING PER CHARACTERISTIC THE LIMITING VALUE OF CURRENT THAT MAY FLOW AND THE SPECIFIC ELECTRICAL CHARACTERISTIC. 2D AND 1B MODE REPLY21AC302AH16 ALAZA 03DESIGNATION,CASE OUTLINE,JOINT ELECTRONIC DEVICE ENGINEERING COUNCIL/JEDEC/ JOINT ELECTRONIC DEVICE ENGINEERING COUNCIL/JEDEC/CASE OUTLINE DESIGNATION THE ALPHA-NUMERIC SYMBOL ASSIGNED BY THE ELECTRONIC INDUSTRIES ASSOCIATION,TO REGISTERED PHYSICAL CONFIGURATIONS OF THE CASES FOR ELECTRONIC ITEMS. 1A MODE REPLY 0 ALBAD 19ELECTRODE INTERNALLY-ELECTRICALLY CONNECTED TO CASE ELECTRODE INTERNALLY-ELECTRICALLY CONNECTED TO CASE THE ELECTRODE WHICH IS INTERNALLY-ELECTRICALLY CONNECTED TO THE CASE OF THE ITEM. SELECT REPLY CODE 10AH17 ALBBD /D/ 19BREED PURITY BREED PURITY AN INDICATION OF PREDICTABILITY AND GENETIC CONSISTANCY WITHIN A BREED. SELECT REPLY CODE 10AA29 ALBCD /D/ 07FEATURE,TOLERANCE,NUCLEAR RADIATION NUCLEAR RADIATION TOLERANCE FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM WILL RETAIN ITS USEFUL PROPERTIES DURING OR AFTER EXPOSURE TO NUCLEAR RADIATION. SELECT REPLY CODE 10AM74 ALBDD /D/ 19CLASSIFICATION,FREQUENCY FREQUENCY CLASSIFICATION THE DISTINGUISHING TITLE THAT DESCRIBES THE FREQUENCY RANGE IN WHICH THE DEVICE IS INTENDED TO OPERATE. SELECT REPLY CODE 10AH18 ALBEJ /D/ 04LENGTH FROM MOUNTING SURFACE,TERMINAL TERMINAL LENGTH FROM MOUNTING SURFACE NONE. 2D AND 1B MODE REPLY21AA051AC20 ALBFD /D/ 17SURFACE TREATMENT,INSIDE,HOUSING HOUSING INSIDE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A HOUSING INSIDE SURFACE. SELECT REPLY CODE 10AD09 ALBGD /D/ 17SURFACE TREATMENT,OUTSIDE,HOUSING HOUSING OUTSIDE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A HOUSING OUTSIDE SURFACE. SELECT REPLY CODE 10AD09 ALBHD /D/ 07SHIELDING,INTERFERENCE,RADIO RADIO INTERFERENCE SHIELDING AN INDICATION OF WHETHER OR NOT SHIELDING AGAINST RADIO INTERFERENCE IS PROVIDED. PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB22 ALBJJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,STUD STUD THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE STUD. 1D AND 1A MODE REPLY12AH06 ALBKJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,RECEPTACLE RECEPTACLE THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE RECEPTACLE. 1D AND 1A MODE REPLY12AH06 ALBLJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,FACILITY,MOUNTING MOUNTING FACILITY THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE MOUNTING FACILITY. 1D AND 1A MODE REPLY12AH06 ALBMD 11METHOD,CONTROL,OPERATING OPERATING CONTROL METHOD THE MEANS BY WHICH THE ITEM IS OPERATED OR CONTROLLED. SELECT REPLY CODE 10AH20 ALBNJ 04LENGTH,OVERALL,REFLECTING ELEMENT REFLECTING ELEMENT OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE REFLECTING ELEMENT. 2D AND 1B MODE REPLY21AA051AC20 ALBPJ 04WIDTH,OVERALL,REFLECTING ELEMENT REFLECTING ELEMENT OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE REFLECTING ELEMENT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALBQJ 04LENGTH,SHANK,POST POST SHANK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ALBRJ 04DIAMETER,OVERALL,REFLECTING ELEMENT REFLECTING ELEMENT OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE REFLECTING ELEMENT. 2D AND 1B MODE REPLY21AA051AC20 ALBSJ 04HEIGHT,OVERALL,REFLECTING ELEMENT REFLECTING ELEMENT OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE REFLECTING ELEMENT. 2D AND 1B MODE REPLY21AA051AC20 ALBTJ 10FREQUENCY RATING,ELEMENT,REFLECTING REFLECTING ELEMENT FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE REFLECTING ELEMENT IS RATED. 2D AND 1B MODE REPLY21AC321AC20 ALBUJ /D/A19AGE AGE A MEASUREMENT OF HOW LONG AN ITEM HAS EXISTED. 2D AND 1A MODE REPLY22AH681AC20 ALBVD /D/ 09MATERIAL,ELEMENT,REFLECTING REFLECTING ELEMENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE REFLECTING ELEMENT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ALBWD /D/ 17SURFACE TREATMENT,ELEMENT,REFLECTING REFLECTING ELEMENT SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE REFLECTING ELEMENT SURFACE. SELECT REPLY CODE 10AD09 ALBXD /D/ 17SURFACE TREATMENT,FRAME FRAME SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE FRAME SURFACE. PLEASE USE MRC SFTT WITH ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 ALBYD 02DESIGN,USAGE USAGE DESIGN INDICATES THE DESIGNED USE OF THE ITEM. SELECT REPLY CODE 10AH21 ALBZJ /D/ 10CONCENTRICITY,DIAMETRIC,MAXIMUM MAXIMUM DIAMETRIC CONCENTRICITY THE MAXIMUM AMOUNT OF DEVIATION ALLOWED BETWEEN THE INNER AND OUTER DIAMETERS,MEASURED AS TOTAL INDICATOR READING. 1D AND 1B MODE REPLY11AA05 ALCAJ /D/ 10PERPENDICULARITY,MAXIMUM,FACE FACE MAXIMUM PERPENDICULARITY THE MAXIMUM AMOUNT OF DEVIATION ALLOWED IN THE FACE SURFACES MEASURED AS TOTAL INDICATOR READING. 1D AND 1B MODE REPLY11AA05 ALCBD /D/ 19FACILITY,MOUNTING MOUNTING FACILITY THE FACILITY FOR MOUNTING THE ITEM. PLEASE USE MRC AZGM IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB89 ALCCD /D/ 19CONDITION FOR WHICH DESIGNED,SURFACE SURFACE CONDITION FOR WHICH DESIGNED AN INDICATION OF THE SURFACE CONDITION ON WHICH THE ITEM IS DESIGNED TO BE USED. SELECT REPLY CODE 10AC67 ALCDG 02DESIGN,USAGE USAGE DESIGN INDICATES THE DESIGNED USE OF THE ITEM. FULL TEXT WRITE-IN 0 ALCED /D/ 09MATERIAL,CANOPY CANOPY MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CANOPY IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ALCFD 01COLOR,CANOPY CANOPY COLOR THE HUE OR TINT OF THE CANOPY. SELECT REPLY CODE 10AD06 ALCGD 19GRADE,INK INK GRADE A DESIGNATION OF THE GRADE OF THE INK,AS DEFINED BY INDUSTRY. SELECT REPLY CODE 10AH22 ALCHD 19QUALITY,TONE TONE QUALITY THE VALUE OF COLOR PECULIAR TO A CERTAIN TONE. SELECT REPLY CODE 10AH23 ALCJD 19ADDITIVE,FURNISHED FURNISHED ADDITIVE THE ADDITIVE SUPPLIED FOR MIXING WITH THE ITEM PRIOR TO USE. SELECT REPLY CODE 10AH24 ALCKA 12QUANTITY,CANOPY CANOPY QUANTITY THE NUMBER OF CANOPIES INCLUDED. 1A MODE REPLY 0 ALCLD 14SHAPE,CANOPY CANOPY SHAPE THE PHYSICAL CONFIGURATION OF THE CANOPY. SELECT REPLY CODE 10AD07 ALCMD 18TYPE,LUMINESCENCE LUMINESCENCE TYPE THE MANNER IN WHICH THE ITEM REACTS TO LIGHT AFTER EXPOSURE TO AN EXTERNAL SOURCE OF RADIANT ENERGY. SELECT REPLY CODE 10AB54 ALCND 11METHOD,OPENING,CANOPY CANOPY OPENING METHOD THE MEANS EMPLOYED FOR OPENING THE CANOPY. SELECT REPLY CODE 10AH25 ALCPD 01COLOR,PACK PACK COLOR THE HUE OR TINT OF THE PACK. SELECT REPLY CODE 10AD06 ALCQD /D/ 09MATERIAL,PACK PACK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PACK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ALCRD 18TYPE,PACK PACK TYPE INDICATES TYE TYPE OF ENCLOSURE IN WHICH THE ITEM IS PACKED. SELECT REPLY CODE 10AH26 ALCSD 02DESIGN,BODY BODY DESIGN THE DESIGN OF THE BODY OF THE ITEM. SELECT REPLY CODE 10AH27 ALCTA 12QUANTITY,LINE,SUSPENSION SUSPENSION LINE QUANTITY THE NUMBER OF SUSPENSION LINES ATTACHED TO THE ITEM. 1A MODE REPLY 0 ALCUG /D/ 03GROMMET SIZE ACCOMMODATED GROMMET SIZE ACCOMMODATED DESIGNATES THE GROMMET SIZE THE ITEM WILL ACCOMMODATE FULL TEXT WRITE-IN 0 ALCVJ A08SWITCH TYPE LOCATION AND QUANTITY SWITCH TYPE LOCATION AND QUANTITY THE SWITCH TYPE, LOCATION AND QUANTITY. 2D AND 1A MODE REPLY22AC823AJ91 ALCWD /D/ 09MATERIAL,LINE,SUSPENSION SUSPENSION LINE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SUSPENSION LINES ARE FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ALCXJ 04LENGTH,LINE,SUSPENSION SUSPENSION LINE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SUSPENSION LINE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALCYD 11METHOD,MOUNTING,TYPE FACE TYPE FACE MOUNTING METHOD THE MEANS OF ATTACHING THE TYPE FACES ON THE ITEM. SELECT REPLY CODE 10AM39 ALCZD /D/ 09MATERIAL,HARNESS HARNESS MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HARNESS IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ALDAD 01COLOR,HARNESS HARNESS COLOR THE HUE OR TINT OF THE HARNESS. SELECT REPLY CODE 10AD06 ALDBD 18TYPE,HARNESS HARNESS TYPE INDICATES THE TYPE OF HARNESS FURNISHED. SELECT REPLY CODE 10AH26 ALDCA 19CODE,MANUFACTURER,HARNESS HARNESS MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE HARNESS. 1A MODE REPLY 0 ALDDJ /D/ 10TORQUE,BREAKING BREAKING TORQUE THE MEASURED TORQUE REQUIRED TO BREAK THE ITEM. 2D AND 1B MODE REPLY21AA561AC20 ALDEA 19NUMBER,PART,HARNESS MANUFACTURER HARNESS MANUFACTURER PART NUMBER THE IDENTIFYING PART NUMBER ASSIGNED TO THE HARNESS BY THE MANUFACTURER. 1A MODE REPLY 0 ALDFD 18TYPE,FRAME FRAME TYPE INDICATES THE TYPE OF FRAME INCLUDED ON THE ITEM. SELECT REPLY CODE 10AH28 ALDGA 12QUANTITY,VANE VANE QUANTITY THE NUMBER OF VANES PROVIDED. 1A MODE REPLY 0 ALDHD 11METHOD,ATTACHMENT,LOAD LOAD ATTACHMENT METHOD THE MEANS USED FOR ATTACHING A LOAD TO THE ITEM. SELECT REPLY CODE 10AH29 ALDJD 19SIZE,TYPE TYPE SIZE A DESIGNATION APPLIED TO THE SIZE OF PRINT. SELECT REPLY CODE 10AH30 ALDKJ 10CAPACITY,LOAD LOAD CAPACITY THE WEIGHT THE ITEM CAN ACCOMMODATE. 2D AND 1B MODE REPLY21AB101AC20 ALDLJ 10SPEED,LOAD LOAD SPEED THE SPECIFIC SPEED AT WHICH THE LOAD IS RATED. 1D AND 1B MODE REPLY11AA34 ALDMG 19LOAD FOR WHICH DESIGNED LOAD FOR WHICH DESIGNED AN INDICATION OF THE LOAD FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 ALDND 19PARACHUTE FOR WHICH DESIGNED PARACHUTE FOR WHICH DESIGNED INDICATES THE TYPE OF PARACHUTE ON WHICH THE ITEM IS DESIGNED TO BE USED. SELECT REPLY CODE 10AH31 ALDPJ 04DISTANCE BETWEEN SPRING MOUNTING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SPRING MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 ALDQD /D/ 07LINE,PACK AND DEPLOYMENT PACK AND DEPLOYMENT LINE AN INDICATION OF WHETHER OR NOT A PACK AND DEPLOYMENT LINE IS INCLUDED. SELECT REPLY CODE 10AA49 ALDRD 02DESIGN,FACE,TYPE TYPE FACE DESIGN A DESIGN DESIGNATION APPLIED TO THE STYLE OF PRINT. SELECT REPLY CODE 10AH32 ALDSD 18TYPE,NUT NUT TYPE INDICATES THE TYPE OF NUT USED IN CONJUNCTION WITH THE ITEM. SELECT REPLY CODE 10AH33 ALDTA 12QUANTITY,SEGMENT SEGMENT QUANTITY THE NUMBER OF SEGMENTS INCLUDED IN THE ITEM. 1A MODE REPLY 0 ALDUA /D/ 09COMPONENT SUPPLY ITEMS AND QUANTITIES COMPONENT SUPPLY ITEMS AND QUANTITIES A LISTING OF MAJOR KIT COMPONENTS WHICH ARE STOCK LISTED AND COMPRISED OF A NATIONAL STOCK NUMBER, AN ITEM NAME, AND THE QUANTITY PROVIDED. 1A MODE REPLY 0 ALDVA /D/ 09COMPONENT NON-SUPPLY ITEMS AND QUANTITIES COMPONENT NON-SUPPLY ITEMS AND QUANTITIES A LISTING OF MAJOR KIT COMPONENTS WHICH ARE NOT STOCKED LISTED AND COMPRISED OF A COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE, MANUFACTURER'S PART NUMBER, ITEM NAME AND QUANTITY PROVIDED. 1A MODE REPLY 0 ALDWD /D/ 07LINER,INNER,SEALING SEALING INNER LINER AN INDICATION OF WHETHER OR NOT A SEALING INNER LINER IS INCLUDED. SELECT REPLY CODE 10AA49 ALDXJ 10ESCAPEMENT,UNIT,TYPE TYPE UNIT ESCAPEMENT A MEASUREMENT OF THE WIDTH OF TYPE WHICH VARIES IN PROPORTION TO THE WIDTH OF THE INDIVIDUAL LETTER. 1D AND 1B MODE REPLY11AA05 ALDYJ 04HEIGHT,INSCRIPTION INSCRIPTION HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE INSCRIPTION,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 ALDZD 18TYPE,CHARACTER CHARACTER TYPE INDICATES THE TYPE OF CHARACTER. SELECT REPLY CODE 10AH34 ALEAD /D/ 07POCKET,REEFING RING/CUTTER,CANOPY CANOPY REEFING RING/CUTTER POCKET INDICATES WHETHER OR NOT THE CANOPY IS PROVIDED WITH REEFING RINGS AND CUTTER POCKETS. SELECT REPLY CODE 10AB22 ALEBJ 04WIDTH,RETAINER RETAINER WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ALECJ 04WIDTH,ROOT ROOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ALEDJ 04THICKNESS,BAND BAND THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE BAND,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALEEJ 04WIDTH,BAND BAND WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BAND,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALEFJ 04WIDTH ACCOMMODATED,PAPER,NOMINAL NOMINAL PAPER WIDTH ACCOMMODATED A MEASUREMENT BASED ON THE NOMINAL WIDTH OF THE PAPER WHICH THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 ALEGD 18TYPE,KEYBOARD KEYBOARD TYPE INDICATES THE TYPE OF KEYBOARD FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AH35 ALEHD 18TYPE,RIBBON RIBBON TYPE INDICATES THE TYPE OF RIBBON ACCOMMODATED BY THE ITEM. SELECT REPLY CODE 10AH36 ALEJD /D/ 07DEVICE,JUSTIFIER JUSTIFIER DEVICE AN INDICATION OF WHETHER OR NOT A DEVICE WHICH ENABLES EVEN RIGHT HAND MARGINS IS PROVIDED. SELECT REPLY CODE 10AB22 ALEKJ 19CAPABILITY,SPACING,CHARACTER CHARACTER SPACING CAPABILITY THE NUMBER OF LETTERS,SYMBOLS,OR NUMERALS WHICH THE ITEM IS CAPABLE OF PRINTING IN A GIVEN HORIZONTAL SPACE. 1D AND 1B MODE REPLY11AB39 ALELJ 19CAPABILITY,SPACING,LINE LINE SPACING CAPABILITY THE NUMBER OF LINES WHICH THE ITEM IS CAPABLE OF PRINTING IN A GIVEN VERTICAL SPACE. 1D AND 1B MODE REPLY11AB39 ALEMA 12QUANTITY,CHANNEL,PERFORATING PERFORATING CHANNEL QUANTITY THE NUMBER OF CHANNELS WHICH THE ITEM WILL PERFORATE. 1A MODE REPLY 0 ALEND /D/ 07DEVICE,RULING,AUTOMATIC FORM AUTOMATIC FORM RULING DEVICE AN INDICATION OF WHETHER OR NOT AN AUTOMATIC FORM RULING DEVICE IS PROVIDED. SELECT REPLY CODE 10AB22 ALEPJ 04DIAMETER,CANOPY CANOPY DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CANOPY HAVING A SHAPE OTHER THAN RECTANGULAR OR SQUARE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ALEQJ 04WIDTH,CANOPY CANOPY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A CANOPY,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALERJ 04LENGTH,CANOPY CANOPY LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CANOPY,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALESD 19PACK FOR WHICH DESIGNED PACK FOR WHICH DESIGNED AN INDICATION OF THE PACK FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AH26 ALETJ A18TYPE AND QUANTITY,HOLE HOLE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF HOLES PROVIDED. 1D AND 1A MODE REPLY12AH37 ALEUA /D/ 12COMPONENT QUANTITY COMPONENT QUANTITY THE TOTAL NUMBER OF MAJOR COMPONENTS INCLUDED IN THE KIT. 1A MODE REPLY 0 ALEVA /D/ 02AERIAL TARGET TYPE FOR WHICH DESIGNED AERIAL TARGET TYPE FOR WHICH DESIGNED THE COMBINED GROUP OF LETTERS, NUMERALS, AND/OR SYMBOLS WHICH COMPRISE THE ASSIGNED TARGET TYPE OF THE ITEM. 1A MODE REPLY 0 ALEWH /D/ 11METHOD AND LOCATION,ACTUATION ACTUATION METHOD AND LOCATION THE MEANS BY WHICH THE ITEM IS ACTUATED AND ITS LOCATION. 2D MODE REPLY 22AC583AJ91 ALEXG /D/ 19SPEC/STD,MATERIAL MATERIAL SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE BASIC MATERIAL. FULL TEXT WRITE-IN 0 ALEYD 19PATTERN,COLOR COLOR PATTERN AN INDICATION OF THE COLOR PATTERNS. SELECT REPLY CODE 10AH38 ALEZD /D/ 19APPLICATION,DESIGN DESIGN APPLICATION THE MEANS OF APPLYING THE DESIGN TO THE ITEM. SELECT REPLY CODE 10AF22 ALFAJ /D/ 10STIMULUS RATING,PRESET,CONTACT ACTUATION POINT CONTACT ACTUATION POINT PRESET STIMULUS RATING THE VALUE OF STIMULUS AT WHICH THE CONTACTS ARE PRESET TO ACTUATE. 3D AND 1B MODE REPLY32AG201AC202AG16 ALFBJ /D/ 10STIMULUS RATING,PRESET,CONTACT DEACTUATION POINT CONTACT DEACTUATION POINT PRESET STIMULUS RATING THE VALUE OF STIMULUS AT WHICH THE CONTACTS ARE PRESET TO DEACTUATE. 3D AND 1B MODE REPLY32AG201AC202AG16 ALFCJ /D/ 10STIMULUS RATING,PRESET,CONTACT ACTING DIFFERENTIAL CONTACT ACTING DIFFERENTIAL PRESET STIMULUS RATING THE DIFFERENCE BETWEEN ACTUATION AND DEACTUATION AT WHICH THE CONTACTS ARE PRESET. 3D AND 1B MODE REPLY32AG201AC202AG16 ALFDD 14SHAPE,DESIGN DESIGN SHAPE THE PHYSICAL CONFIGURATION OF THE DESIGN. SELECT REPLY CODE 10AH39 ALFED /D/ 07STAFF STAFF AN INDICATION OF WHETHER OR NOT A STAFF IS INCLUDED. SELECT REPLY CODE 10AA49 ALFFD /D/ 07FRINGE FRINGE AN INDICATION OF WHETHER OR NOT FRINGE IS INCLUDED. SELECT REPLY CODE 10AA49 ALFGH /D/ 08LOCATION AND FUNCTION,DEVICE,LOCKING LOCKING DEVICE LOCATION AND FUNCTION INDICATES THE LOCATION,BY FUNCTION,OF THE LOCKING DEVICE. 2D MODE REPLY 22AG162AG21 ALFHD /D/ 08LOCATION,SECTION SECTION LOCATION INDICATES THE LOCATION OF A SECTION. SELECT REPLY CODE 10AE46 ALFJD /D/ 07HOLE,VENT VENT HOLE AN INDICATION OF WHETHER OR NOT VENT HOLES ARE INCLUDED. SELECT REPLY CODE 10AA49 ALFKD /D/ 07CASE CASE AN INDICATION OF WHETHER OR NOT A CONTAINER FROM WHICH THE ITEM IS COMPLETELY REMOVABLE IS PROVIDED. IF PROVIDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB22 ALFLJ /D/ 04DIAMETER AND LOCATION DIAMETER AND LOCATION THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY AND TERMINATES AT THE CIRCUMFERENCE,AND THE LOCATION ON THE ITEM. 3D AND 1B MODE REPLY31AA051AC203AE46 ALFMD /D/ 19ATTACHMENT,ORNAMENTAL ORNAMENTAL ATTACHMENT THE ORNAMENT/S/ THAT IS ATTACHED TO THE ITEM. SELECT REPLY CODE 10AH40 ALFNJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,HOLE,MOUNTING MOUNTING HOLE THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE MOUNTING HOLE. 1D AND 1A MODE REPLY12AH06 ALFPD 03DESIGNATION,MARKING MARKING DESIGNATION A DESIGNATION OF THE MARKING(S) ON THE ITEM OR THAT IS THE ITEM. SELECT REPLY CODE 10AF91 ALFQG 19INSCRIPTION/DESIGN INSCRIPTION/DESIGN THE LETTERING OR TYPE OF DESIGN ON THE ITEM,OR THAT IS THE ITEM. FULL TEXT WRITE-IN 0 ALFRD /D/ 01COLOR,DESIGN DESIGN COLOR THE HUE OR TINT OF THE DESIGN. SELECT REPLY CODE 10AD06 ALFSD /D/ 01COLOR,STRIPE STRIPE COLOR THE HUE OR TINT OF THE STRIPE. SELECT REPLY CODE 10AD06 ALFTD 18TYPE,FILLET FILLET TYPE INDICATES THE TYPE OF FILLET. SELECT REPLY CODE 10AH41 ALFUJ /D/ 10VOLTAGE IN VOLTS AND CURRENT TYPE VOLTAGE IN VOLTS AND CURRENT TYPE THE TOTAL ELECTRICAL VOLTAGE, EXPRESSED IN VOLTS, AND THE TYPE OF CURRENT, WHETHER ALTERNATING OR DIRECT. 2D AND 1B MODE REPLY22AN871AC20 ALFVD /D/ 18BAFFLE TYPE BAFFLE TYPE INDICATES THE TYPE OF BAFFLE SELECT REPLY CODE 10AF57 ALFWD 19FEATURE,CUT CUT FEATURE A DISTINCT OR OUTSTANDING PART,QUALITY,OR CHARACTERISTIC OF A PIECE CUT. SELECT REPLY CODE 10AH42 ALFXA 12QUANTITY,SIDE,INSCRIBED INSCRIBED SIDE QUANTITY THE NUMBER OF SIDES OF THE ITEM THAT HAVE INSCRIBED,EMBOSSED,OR WOVEN MARKING/S/. 1A MODE REPLY 0 ALFYJ 04DISTANCE BETWEEN FIRST MOUNTING FACILITY ALONG LENGTH AND MOUNTING FACILITY ALONG WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FIRST MOUNTING FACILITY ALONG LENGTH AND MOUNTING FACILITY ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ALFZD 01COLOR,BORDER BORDER COLOR THE HUE OR TINT OF THE BORDER OF THE ITEM. SELECT REPLY CODE 10AD06 ALGAD 19SURFACE,REFLECTING REFLECTING SURFACE THE SPECIFIC SURFACE OF THE ITEM THAT HAS THE QUALITY OF REFLECTING LIGHT. SELECT REPLY CODE 10AJ91 ALGBD /D/ 19SURFACE,LUMINOUS LUMINOUS SURFACE THE SPECIFIC SURFACE OF THE ITEM,COATED WITH FLUORESCENT OR PHOSPHORESCENT MATERIALS,THAT HAS THE QUALITY OF GIVING OFF LIGHT CAUSED BY THE ABSORPTION OF RADIANT ENERGY. SELECT REPLY CODE 10AJ91 ALGCG 19CONFIGURATION,MOUNTING MOUNTING CONFIGURATION THE PATTERN OR ARRANGEMENT THAT DESCRIBES THE MOUNTING CONFIGURATION OF THE ITEM. FULL TEXT WRITE-IN 0 ALGDJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,END,FIRST FIRST END THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE FIRST END. 1D AND 1A MODE REPLY12AH06 ALGED 19FORM,STRUCTURAL,INSCRIPTION INSCRIPTION STRUCTURAL FORM THE STRUCTURAL FORM OF THE LETTER/S/ OR NUMERAL/S/ IN THE INSCRIPTION,OR THE LETTER,NUMERAL,OR SYMBOL THAT IS THE ITEM. SELECT REPLY CODE 10AF22 ALGFJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,END,SECOND SECOND END THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE SECOND END. 1D AND 1A MODE REPLY12AH06 ALGGJ 04WIDTH,INSCRIPTION INSCRIPTION WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE INSCRIPTION. 2D AND 1B MODE REPLY21AA051AC20 ALGHJ 10CAPACITY,GREASE GREASE CAPACITY THE WEIGHT OR VOLUME OF GREASE THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY12AG67 ALGJJ 10CAPACITY,OIL OIL CAPACITY THE VOLUME OF OIL THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY12AG67 ALGKD /D/ 08LOCATION,HINGE,LID LID HINGE LOCATION INDICATES THE LOCATION OF THE HINGE IN RELATION TO THE LID OPENING. SELECT REPLY CODE 10AJ91 ALGLD /D/ 07GASKET,COVER COVER GASKET AN INDICATION OF WHETHER OR NOT A GASKET USED TO SEAL THE COVER IS INCLUDED. SELECT REPLY CODE 10AA49 ALGMD /D/ 09MATERIAL,BASIC,SEALING WASHER SEALING WASHER BASIC MATERIAL THE BASIC ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SEALING WASHER IS FABRICATED. SELECT REPLY CODE 10AD09 ALGND 11METHOD,RELIEF,PRESSURE PRESSURE RELIEF METHOD THE MEANS PROVIDED FOR RELIEVING PRESSURE FROM AN ITEM. SELECT REPLY CODE 10AB99 ALGPD 18TYPE,ADHESIVE ADHESIVE TYPE INDICATES THE TYPE OF ADHESIVE USED TO AFFIX THE ITEM TO ANOTHER SURFACE. SELECT REPLY CODE 10AB47 ALGQD /D/ 08LOCATION,PORT,RELIEF RELIEF PORT LOCATION INDICATES THE LOCATION OF THE RELIEF PORT IN THE ITEM. SELECT REPLY CODE 10AJ91 ALGRD 08LOCATION,ADHESIVE ADHESIVE LOCATION INDICATES THE PHYSICAL LOCATION OF THE ADHESIVE APPLIED TO THE ITEM. SELECT REPLY CODE 10AE46 ALGSD /D/ 07BACKING,PROTECTIVE,REMOVABLE REMOVABLE PROTECTIVE BACKING AN INDICATION OF WHETHER OR NOT A REMOVABLE PROTECTIVE BACKING IS INCLUDED. SELECT REPLY CODE 10AA49 ALGTJ 04RADIUS,CLEARANCE,ASSEMBLY ASSEMBLY CLEARANCE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ALGUD 18TYPE,PROBE PROBE TYPE INDICATES THE TYPE OF PROBE SELECT REPLY CODE 10AJ12 ALGVD /D/ 18SOURCE,COMPRESSED AIR COMPRESSED AIR SOURCE INDICATES THE TYPE OF COMPRESSED AIR SOURCE WHICH IS USED. SELECT REPLY CODE 10AK54 ALGWJ 04LENGTH,HANGER,STEM STEM HANGER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE STEM HANGER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALGXD /D/ 08LOCATION,SURFACE,MOUNTING MOUNTING SURFACE LOCATION INDICATES THE LOCATION OF THE MOUNTING SURFACE ON THE ITEM. SELECT REPLY CODE 10AE46 ALGYD /D/ 07GUARD,PROTECTIVE PROTECTIVE GUARD AN INDICATION OF WHETHER OR NOT A PROTECTIVE GUARD IS INCLUDED. SELECT REPLY CODE 10AA49 ALGZA 12QUANTITY,HOLE,CLEARANCE CLEARANCE HOLE QUANTITY THE NUMBER OF HOLES PROVIDED IN THE ITEM FOR CLEARANCE. 1A MODE REPLY 0 ALHAA 12QUANTITY PER FORM QUANTITY PER FORM THE NUMBER OF ITEMS FURNISHED PER FORM. 1A MODE REPLY 0 ALHBG /D/ 19FEATURE,SURFACE SURFACE FEATURE A NARRATIVE EXPRESSION USED TO DEFINE THE SURFACE OF THE ITEM. PLEASE USE MRC AZAH IN PLACE OF THIS DISCONTINUED MRC. FULL TEXT WRITE-IN 0 ALHCD /D/ 19PERFORATION,DETACHMENT DETACHMENT PERFORATION AN INDICATION OF WHETHER OR NOT DETACHMENT PERFORATIONS ARE INCLUDED. SELECT REPLY CODE 10AA49 ALHDJ 04LENGTH,ROLL ROLL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ROLL,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALHEJ 04WIDTH,ROLL ROLL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ROLL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALHFD 18TYPE,PREPARATION PREPARATION TYPE INDICATES THE TYPE OF PROCESS WHICH PREPARES THE ITEM FOR USE. SELECT REPLY CODE 10AH43 ALHGD /D/ 07DEVICE,ATTACHMENT ATTACHMENT DEVICE AN INDICATION OF WHETHER OR NOT AN ATTACHMENT DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 ALHHD 19HABITAT,ENVIRONMENTAL ENVIRONMENTAL HABITAT THE PLACE OR TYPE OF SITE WHERE THE ITEM IS COMMONLY FOUND. SELECT REPLY CODE 10AH44 ALHJD 01COLOR,MEAT MEAT COLOR THE SPECIFIC COLOR OF THE EDIBLE FLESH. SELECT REPLY CODE 10AD06 ALHKD 18TYPE,PACK,PRESERVATIVE PRESERVATIVE PACK TYPE INDICATES THE TYPE OF PACK USED TO PRESERVE THE ITEM FOR FUTURE USE. SELECT REPLY CODE 10AH45 ALHLJ 04LENGTH,SIDE SIDE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SIDE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALHMJ /D/ 04DIAMETER,OPEN OPEN DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ALHNJ /D/ 04WIDTH,FOLDED FOLDED WIDTH THE MEASURED WIDTH OF THE ITEM WHEN IN A FOLDED POSITION. 2D AND 1B MODE REPLY21AA051AC20 ALHPJ 04LENGTH,BOX BOX LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A BOX,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALHQJ 04WIDTH,BOX BOX WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BOX,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALHRD 19GARMENT FOR WHICH DESIGNED GARMENT FOR WHICH DESIGNED THE GARMENT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AH80 ALHSJ /D/ 04WIDTH,FRAME FRAME WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ALHTG /D/ 10WEIGHT/SIZE/NUMBER WEIGHT/SIZE/NUMBER AN INDICATION OF THE WEIGHT,SIZE,OR NUMBER OF THE INDIVIDUAL UNITS. FULL TEXT WRITE-IN 0 ALHUD /D/ 12STATIC CAPACITY,VACUUM ANCHOR VACUUM ANCHOR STATIC CAPACITY INDICATES THE VACUUM ANCHOR STATIC CAPACITY OF THE ITEM. SELECT REPLY CODE 10AB16 ALHVJ /D/ 04DIAMETER,INSIDE,STEPPED BORE STEPPED BORE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR BORE, AND TERMINATES AT THE CIRCUMFERENCE. 3D AND 1B MODE REPLY33AJ911AA051AC20 ALHWJ 04DIAMETER,OVERALL,WIRE ACCOMMODATED WIRE ACCOMMODATED OVERALL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ALHXJ 04WIDTH,MAJOR MAJOR WIDTH THE LARGEST MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALHYJ 04DIAMETER,CIRCLE,MOUNTING HOLE MOUNTING HOLE CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ALHZJ /D/ 04SIZE AND LOCATION,SURFACE,WRENCHING WRENCHING SURFACE SIZE AND LOCATION DESIGNATES THE SIZE OF THE WRENCHING SURFACE AND ITS LOCATION ON THE ITEM. 3D AND 1B MODE REPLY31AA051AC203AJ91 ALJAH /D/ 14SHAPE AND LOCATION,SURFACE,WRENCHING WRENCHING SURFACE SHAPE AND LOCATION THE PHYSICAL CONFIGURATION OF THE WRENCHING SURFACE AND ITS LOCATION ON THE ITEM. 3D MODE REPLY 33AD073AJ912AH46 ALJBD 19EQUIPMENT TO WHICH ATTACHED EQUIPMENT TO WHICH ATTACHED THE NAME OF THE EQUIPMENT TO WHICH THE ITEM IS ATTACHED. SELECT REPLY CODE 10AD34 ALJCD 19FORM,STRUCTURAL STRUCTURAL FORM AN INDICATION OF THE STRUCTURAL FEATURE/S/ OF THE ITEM. SELECT REPLY CODE 10AH47 ALJDD /D/ 07CUSHIONING,ABSORBING,SHOCK SHOCK ABSORBING CUSHIONING AN INDICATION OF WHETHER OR NOT SHOCK ABSORBING CUSHIONING IS PROVIDED. SELECT REPLY CODE 10AB22 ALJED /D/ 07RUNNERS,SLED SLED RUNNERS AN INDICATION OF WHETHER OR NOT SLED RUNNERS ARE PROVIDED. SELECT REPLY CODE 10AB22 ALJFD /D/ 09MATERIAL,WEBBING WEBBING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WEBBING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. POSSIBLE REPLACEMENT MRC: CZLA - MATERIAL,HOUSING; SELECT REPLY CODE 10AD09 ALJGD 19CLASSIFICATION,GROUP GROUP CLASSIFICATION AN INDICATION OF HOW THE ITEMS ARE GROUPED FOR CLASSIFICATION. SELECT REPLY CODE 10AH48 ALJHD 19FLAVOR FLAVOR THE QUALITY,BLEND,OR AROMA OF THE ITEM THAT AFFECTS SENSE OF TASTE. SELECT REPLY CODE 10AH49 ALJJD 19INGREDIENT,OPTIONAL OPTIONAL INGREDIENT AN INGREDIENT WHICH MAY BE ADDED TO OR MIXED WITH THE BASIC ITEM. SELECT REPLY CODE 10AH50 ALJKJ /D/A08LOCATION AND QUANTITY,LOOP LOOP LOCATION AND QUANTITY INDICATES THE LOCATION AND NUMBER OF LOOP(S) ON THE ITEM. 1D AND 1A MODE REPLY13AE46 ALJLD 18TYPE,PROTECTION,LOOP LOOP PROTECTION TYPE INDICATES THE TYPE OF DEVICE INCLUDED TO PROTECT THE LOOPS. SELECT REPLY CODE 10AF34 ALJMD /D/ 08LOCATION,PROTECTOR,LOOP LOOP PROTECTOR LOCATION INDICATES THE LOCATION OF THE PROTECTOR FOR THE LOOP(S). SELECT REPLY CODE 10AE46 ALJND /D/ 07PIN WITH STREAMER,SAFETY SAFETY PIN WITH STREAMER AN INDICATION OF WHETHER OR NOT A SAFETY PIN WITH STREAMER IS INCLUDED. SELECT REPLY CODE 10AA49 ALJPD 03DESIGNATION,SIZE SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. SELECT REPLY CODE 10AF81 ALJQJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,BUSHING,MOUNTING MOUNTING BUSHING THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE MOUNTING BUSHING. 1D AND 1A MODE REPLY12AH06 ALJRD 18TYPE,CONSTRUCTION,STATIC LINE STATIC LINE CONSTRUCTION TYPE INDICATES THE TYPE OF CONSTRUCTION WITH WHICH THE STATIC LINE IS MADE. SELECT REPLY CODE 10AH52 ALJSJ 04WIDTH,BEAM,MOLDED MOLDED BEAM WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOLDED BEAM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALJTD /D/ 07BAND,OPENING,ELASTIC ELASTIC OPENING BAND AN INDICATION OF WHETHER OR NOT ELASTIC OPENING BAND/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 ALJUJ /D/ 04DEPTH,STEPPED BORE STEPPED BORE DEPTH NONE. 3D AND 1B MODE REPLY33AJ911AA051AC20 ALJVD /D/ 02EARPHONE TYPE EARPHONE TYPE INDICATES THE TYPE(S) OF EARPHONES(S) WHICH IS/ARE INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AC52 ALJWD 14SHAPE,FRAME FRAME SHAPE THE PHYSICAL CONFIGURATION OF THE FRAME. SELECT REPLY CODE 10AD07 ALJXJ 10DRAFT,LOADED LOADED DRAFT THE DEPTH OF WATER THE ITEM DRAWS WHEN LOADED. 2D AND 1B MODE REPLY21AA051AC20 ALJYJ 10SPEED,MAXIMUM,LOADED LOADED MAXIMUM SPEED THE RATED MAXIMUM SPEED OF THE ITEM WHEN LOADED. 1D AND 1B MODE REPLY11AA34 ALJZJ 10SPEED,MAXIMUM,LIGHT LIGHT MAXIMUM SPEED THE RATED MAXIMUM SPEED OF THE ITEM WITHOUT LOAD. 1D AND 1B MODE REPLY11AA34 ALKAB 10RANGE AT MAXIMUM SPEED IN NAUTICAL MILES,RATED RATED RANGE AT MAXIMUM SPEED IN NAUTICAL MILES THE DISTANCE THE ITEM WILL TRAVEL AT MAXIMUM SPEED,EXPRESSED IN NAUTICAL MILES. 1B MODE REPLY 0 ALKBJ A18TYPE AND QUANTITY,ENGINE ENGINE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF ENGINES INCLUDED WITH THE ITEM. 1D AND 1A MODE REPLY12AG27 ALKCD /D/ 01COLOR OF THE ACOUSTIC TUBE COLOR OF THE ACOUSTIC TUBE INDICATES THE COLOR OF THE COILED ACOUSTIC TUBE WHICH IS INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AD06 ALKDJ 04LENGTH,FRAME FRAME LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FRAME,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALKEJ 04WIDTH,FRAME FRAME WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FRAME,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALKFG /D/ 19SPEC/STD,MATERIAL,WEBBING WEBBING MATERIAL SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE WEBBING MATERIAL. FULL TEXT WRITE-IN 0 ALKGD 14SHAPE,PANEL,MAIN MAIN PANEL SHAPE THE PHYSICAL CONFIGURATION OF THE MAIN PANEL. SELECT REPLY CODE 10AD07 ALKHJ 04LENGTH,PANEL,MAIN MAIN PANEL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE MAIN PANEL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALKJJ 04WIDTH,PANEL,MAIN MAIN PANEL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MAIN PANEL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALKKB 10HORSEPOWER,BRAKE,ENGINE ENGINE BRAKE HORSEPOWER THE POWER ACTUALLY DELIVERED BY THE ENGINE,AT A SPECIFIED SPEED,WHICH IS AVAILABLE FOR DRIVING THE ITEM. 1B MODE REPLY 0 ALKLB 10SPEED IN RPM,HORSEPOWER RATING,ENGINE ENGINE HORSEPOWER RATING SPEED IN RPM THE ROTARY SPEED OF THE ENGINE AT WHICH THE HORSEPOWER RATING IS DETERMINED,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 ALKMA 12QUANTITY,PROPELLER PROPELLER QUANTITY THE NUMBER OF PROPELLERS INCLUDED ON THE ITEM. 1A MODE REPLY 0 ALKND 11METHOD,PROPULSION PROPULSION METHOD THE MEANS USED TO PROPEL THE ITEM. SELECT REPLY CODE 10AH53 ALKPJ 10DISPLACEMENT,TOTAL,RESERVE BUOYANCY RESERVE BUOYANCY TOTAL DISPLACEMENT THE TOTAL AMOUNT OF WATER DISPLACED BY THE RESERVE BUOYANCY. 2D AND 1B MODE REPLY21AD421AC20 ALKQD 02DESIGN,HULL HULL DESIGN THE BASIC DESIGN OF THE HULL. SELECT REPLY CODE 10AH54 ALKRD 01COLOR,CANOPY,RESERVE RESERVE CANOPY COLOR THE HUE OR TINT OF THE RESERVE CANOPY. SELECT REPLY CODE 10AD06 ALKSJ 04DIAMETER,CANOPY,RESERVE RESERVE CANOPY DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A RESERVE CANOPY HAVING A SHAPE OTHER THAN RECTANGULAR OR SQUARE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ALKTD /D/ 09MATERIAL,CANOPY,RESERVE RESERVE CANOPY MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE RESERVE CANOPY IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ALKUD /D/ 08EARPHONE SIDE EARPHONE SIDE INDICATES WHETHER THE EARPHONE IS SUITABLE FOR THE USER'S RIGHT OF LEFT EAR. SELECT REPLY CODE 10AA38 ALKVD 18TYPE,LIFE LINE LIFE LINE TYPE INDICATES THE TYPE OF LIFE LINE WHICH IS USED. SELECT REPLY CODE 10AB28 ALKWD 11METHOD,OPENING,RESERVE CANOPY RESERVE CANOPY OPENING METHOD THE MEANS EMPLOYED FOR OPENING THE RESERVE CANOPY. SELECT REPLY CODE 10AH25 ALKXD 01COLOR,PACK,RESERVE RESERVE PACK COLOR THE HUE OR TINT OF THE RESERVE PACK. SELECT REPLY CODE 10AD06 ALKYD /D/ 09MATERIAL,PACK,RESERVE RESERVE PACK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE RESERVE PACK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ALKZD 18TYPE,PACK,RESERVE RESERVE PACK TYPE INDICATES THE TYPE OF ENCLOSURE IN WHICH THE RESERVE ITEM IS PACKED. SELECT REPLY CODE 10AH26 ALLAA 12QUANTITY,PIN,LOCKING LOCKING PIN QUANTITY THE NUMBER OF LOCKING PINS PROVIDED. 1A MODE REPLY 0 ALLBJ 04LENGTH,CABLE CABLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CABLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALLCD 01COLOR,WEBBING WEBBING COLOR THE HUE OR TINT OF THE WEBBING. SELECT REPLY CODE 10AD06 ALLDJ 04LENGTH,WEBBING WEBBING LENGTH A MESSUREMENT OF THE LONGEST DIMENSION OF THE WEBBING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALLEJ 04WIDTH,WEBBING WEBBING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE WEBBING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALLFD /D/ 07FEATURE,CLINKER BUILT CLINKER BUILT FEATURE AN INDICATION OF WHETHER OR NOT A CLINKER BUILT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ALLGA 19CAPACITY,PERSONNEL PERSONNEL CAPACITY THE NUMBER OF PERSONS THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 ALLHA 19PATIENTS ACCOMMODATED,LITTER LITTER PATIENTS ACCOMMODATED THE NUMBER OF LITTER PATIENTS THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 ALLJA 12QUANTITY,THWART THWART QUANTITY THE NUMBER OF THWARTS INCLUDED IN THE ITEM. 1A MODE REPLY 0 ALLKA 12QUANTITY,COMPARTMENT,BLADDER BLADDER COMPARTMENT QUANTITY THE NUMBER OF BLADDER COMPARTMENTS INCLUDED IN THE ITEM. 1A MODE REPLY 0 ALLLA 12QUANTITY,PADDLE PADDLE QUANTITY THE NUMBER OF PADDLES INCLUDED WITH THE ITEM. 1A MODE REPLY 0 ALLMD /D/ 18TYPE,GEAR,RELEASE RELEASE GEAR TYPE INDICATES THE TYPE OF GEAR USED TO RELEASE THE ITEM. SELECT REPLY CODE 10AH55 ALLNJ 10SPACING,GEAR,RELEASE RELEASE GEAR SPACING THE SPACING DISTANCE OF THE RELEASE GEAR. 2D AND 1B MODE REPLY21AA051AC20 ALLPD /D/ 18TYPE,RIGGING,SAIL SAIL RIGGING TYPE INDICATES THE TYPE OF SAIL RIG PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AH56 ALLQJ 04LENGTH,LIFE LINE LIFE LINE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A LIFE LINE. 2D AND 1B MODE REPLY21AA051AC20 ALLRD 18FUNCTION,AIRCRAFT AIRCRAFT FUNCTION DESCRIBES THE PURPOSE FOR WHICH THE AIRCRAFT IS DESIGNED. SELECT REPLY CODE 10AP90 ALLSD /D/ 07MOUNT,GUN GUN MOUNT AN INDICATION OF WHETHER OR NOT THE ITEM IS EQUIPPED WITH GUN MOUNTS. SELECT REPLY CODE 10AA49 ALLTD /D/ 07BRACKET,MOTOR,OUTBOARD OUTBOARD MOTOR BRACKET AN INDICATION OF WHETHER OR NOT THE ITEM IS EQUIPPED WITH AN OUTBOARD MOTOR BRACKET. SELECT REPLY CODE 10AA49 ALLUD 11METHOD,TAKE OFF TAKE OFF METHOD INDICATES THE TAKE OFF MEANS OF THE AIRCRAFT. SELECT REPLY CODE 10AP90 ALLVD 11METHOD,RECOVERY RECOVERY METHOD INDICATES THE MEANS FOR RECOVERING THE AIRCRAFT. SELECT REPLY CODE 10AP90 ALLWD /D/ 07CABIN,EQUIPMENT,RADIO RADIO EQUIPMENT CABIN AN INDICATION OF WHETHER OR NOT A CABIN FOR RADIO EQUIPMENT IS INCLUDED. SELECT REPLY CODE 10AA49 ALLXD /D/ 07ACCOMMODATION,BOAT,NESTED NESTED BOAT ACCOMMODATION AN INDICATION OF WHETHER OR NOT A NESTED BOAT ACCOMMODATION IS INCLUDED. SELECT REPLY CODE 10AA49 ALLYD /D/ 07RUDDER RUDDER AN INDICATION OF WHETHER OR NOT THE ITEM IS EQUIPPED WITH A RUDDER. SELECT REPLY CODE 10AA49 ALLZD /D/ 07CENTERBOARD CENTERBOARD AN INDICATION OF WHETHER OR NOT THE ITEM IS EQUIPPED WITH A CENTERBOARD. SELECT REPLY CODE 10AA49 ALMAD /D/ 07TOWLINE TOWLINE AN INDICATION OF WHETHER OR NOT THE ITEM IS EQUIPPED WITH A TOWLINE/S/. SELECT REPLY CODE 10AA49 ALMBD /D/ 07CURTAIN,SPRAY SPRAY CURTAIN AN INDICATION OF WHETHER OR NOT THE ITEM IS EQUIPPED WITH A SPRAY CURTAIN. SELECT REPLY CODE 10AA49 ALMCG 19USE FOR WHICH PERMANENTLY CONVERTED USE FOR WHICH PERMANENTLY CONVERTED THE USE FOR WHICH THE ITEM HAS BEEN PERMANENTLY CONVERTED. FULL TEXT WRITE-IN 0 ALMDG /D/ 03DESIGNATOR,ARRANGEMENT,CONVERSION CONVERSION ARRANGEMENT DESIGNATOR THE ARRANGEMENT PLAN OR DRAWING NUMBER CONTROLLING THE CONVERSION. FULL TEXT WRITE-IN 0 ALMEJ 10HARDNESS RATING,MATERIAL MATERIAL HARDNESS RATING A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF THE MATERIAL WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE. 2D AND 1B MODE REPLY22AC261AC20 ALMFJ /D/ 10WEIGHT,HOISTING HOISTING WEIGHT THE HOISTING WEIGHT OF THE ITEM. 2D AND 1B MODE REPLY22AB161AC20 ALMGJ 04LENGTH,COMPONENT COMPONENT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE COMPONENT,IN DISTINCTION FROM WIDTH. 3D AND 1B MODE REPLY31AA051AC202AF37 ALMHD 11METHOD,HOISTING HOISTING METHOD THE MEANS USED TO HOIST THE ITEM. SELECT REPLY CODE 10AD28 ALMJJ 04DIAMETER,OUTSIDE,COMPONENT COMPONENT OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COMPONENT,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 3D AND 1B MODE REPLY31AA051AC202AF37 ALMKJ 04WIDTH,COMPONENT COMPONENT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE COMPONENT,IN DISTINCTION FROM THICKNESS. 3D AND 1B MODE REPLY31AA051AC202AF37 ALMLD 19DEVICE,TIGHTENING TIGHTENING DEVICE THE TYPE OF TIGHTENING DEVICE INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AB87 ALMMA 19CODE,MANUFACTURER,TIGHTENING DEVICE TIGHTENING DEVICE MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE TIGHTENING DEVICE. 1A MODE REPLY 0 ALMNA 19NUMBER,PART,TIGHTENING DEVICE MANUFACTURER TIGHTENING DEVICE MANUFACTURER PART NUMBER THE IDENTIFYING PART NUMBER ASSIGNED TO THE TIGHTENING DEVICE BY THE MANUFACTURER. 1A MODE REPLY 0 ALMPL 16STYLE,HANDLE HANDLE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HANDLE. 1L MODE REPLY 0 ALMQL 16STYLE,PLATE,MOUNTING MOUNTING PLATE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE MOUNTING PLATE. 1L MODE REPLY 0 ALMRL 16STYLE,SHAFT,INTEGRAL INTEGRAL SHAFT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE INTEGRAL SHAFT. 1L MODE REPLY 0 ALMSA 04ANGLE IN DEG,SWING SWING ANGLE IN DEG THE SWING ANGLE OF THE ITEM,EXPRESSED IN DEGREES. 1A MODE REPLY 0 ALMTD /D/ 18TYPE,PLATE,ESCUTCHEON ESCUTCHEON PLATE TYPE INDICATES THE TYPE OF ESCUTCHEON PLATE. SELECT REPLY CODE 10AC01 ALMUD 18PAYLOAD PAYLOAD INDICATES THE TYPE OF PAYLOAD. SELECT REPLY CODE 10AP90 ALMVD 18LINK,DATA DATA LINK INDICATES THE TYPE OF DATA LINK. SELECT REPLY CODE 10AP90 ALMWD /D/ 07LOCK,HANDLE HANDLE LOCK AN INDICATION OF WHETHER OR NOT A HANDLE LOCK IS INCLUDED. SELECT REPLY CODE 10AA49 ALMXD /D/ 07COVER,LOCK LOCK COVER AN INDICATION OF WHETHER OR NOT A LOCK COVER IS INCLUDED. SELECT REPLY CODE 10AA49 ALMYD /D/ 07ACCOMMODATION,LOCK LOCK ACCOMMODATION AN INDICATION OF WHETHER OR NOT A LOCK ACCOMMODATION IS INCLUDED. SELECT REPLY CODE 10AA49 ALMZJ 10CLEARANCE,HANDLE HANDLE CLEARANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 ALNAJ 04LENGTH FROM GROOVE TO SHAFT END LENGTH FROM GROOVE TO SHAFT END NONE. 2D AND 1B MODE REPLY21AA051AC20 ALNBJ 10TRAVERSE,INSIDE INSIDE TRAVERSE A LATERAL MEASUREMENT TAKEN FROM ONE INNER WALL OR SIDE TO AN OPPOSITE INNER WALL OR SIDE. 2D AND 1B MODE REPLY21AA051AC20 ALNCJ 04DIAMETER,OUTSIDE,HUB HUB OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HUB,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ALNDJ 04DIAMETER,INSIDE,HUB HUB INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE HWICH PASSES THROUGH THE CENTER OF THE HUB,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ALNEJ 04DIAMETER,OUTSIDE,CORE CORE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CORE,AND TERMINATES ATTHE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ALNFJ 04DIAMETER,HOLE,SHAFT SHAFT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SHAFT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ALNGJ 04LENGTH,HOLE,SPINDLE SPINDLE HOLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SPINDLE HOLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALNHJ 04WIDTH,HOLE,SPINDLE SPINDLE HOLE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SPINDLE HOLE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALNJJ 04WIDTH,FILM,ACCOMMODATED ACCOMMODATED FILM WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ACCOMMODATED FILM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALNKJ 04LENGTH,FILM,ACCOMMODATED ACCOMMODATED FILM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FILM THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALNLJ 04WIDTH,TAPE,ACCOMMODATED ACCOMMODATED TAPE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ACCOMMODATED TAPE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALNMD /D/ 07CAN,REEL REEL CAN AN INDICATION OF WHETHER OR NOT A REEL CAN IS PROVIDED. SELECT REPLY CODE 10AB22 ALNND /D/ 09MATERIAL,CAN CAN MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CAN IS FABRICATED,EXCLUDING ANY SURFACE MATERIAL. SELECT REPLY CODE 10AD09 ALNPD /D/ 18TYPE,CAN CAN TYPE INDICATES THE TYPE OF CAN FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AH57 ALNQJ 10PERCENTAGE,INGREDIENT INGREDIENT PERCENTAGE A NUMERIC VALUE OF THE CONSTITUENTS AND THEIR EXACT PROPORTIONS THAT MAKE UP A COMPOUND. 1D AND 1B MODE REPLY12AH58 ALNRD 18TYPE,PRODUCT PRODUCT TYPE INDICATES THE TYPE(S) OF PRODUCT. SELECT REPLY CODE 10AH59 ALNSJ /D/ 10WEIGHT,LOWERING,LOADED LOADED LOWERING WEIGHT THE LOWERING WEIGHT OF THE ITEM WHEN LOADED. 2D AND 1B MODE REPLY22AB161AC20 ALNTJ 10POWER RATING PER CHARACTERISTIC,MAXIMUM,ABSOLUTE ABSOLUTE MAXIMUM POWER RATING PER CHARACTERISTIC THE MAXIMUM LIMITING VALUE OF ELECTRICAL POWER THAT MAY BE DISSIPATED AND THE SPECIFIC ELECTRICAL CHARACTERISTIC. 2D AND 1B MODE REPLY22AB492AH63 ALNUA 10WEIGHT IN KILOGRAMS,UNLADEN UNLADEN WEIGHT IN KILOGRAMS THE WEIGHT IN KILOGRAMS OF THE AIRCRAFT WITHOUT A PAYLOAD. 1A MODE REPLY 0 ALNVB /D/ 10RANGE AT MAXIMUM SPEED,RATED RATED RANGE AT MAXIMUM SPEED THE RATED DISTANCE THE ITEM WILL TRAVEL AT MAXIMUM SPEED, EXPRESSED IN MILES. 1B MODE REPLY 0 ALNWB 10TEMP IN DEG CELSIUS AT WHICH ABSOLUTE MAXIMUM POWER RATING IS ESTABLISHED TEMP IN DEG CELSIUS AT WHICH ABSOLUTE MAXIMUM POWER RATING IS ESTABLISHED THE TEMPERATURE AT WHICH THE ABSOLUTE MAXIMUM POWER DISSIPATION CAPABILITIES OF THE ITEM ARE ESTABLISHED,EXPRESSED IN DEGREES CELSIUS. 1B MODE REPLY 0 ALNXD /D/ 08LOCATION,MEASUREMENT,TEMP,ABSOLUTE MAXIMUM POWER RATING ABSOLUTE MAXIMUM POWER RATING TEMP MEASUREMENT LOCATION THE POINT AT WHICH THE ABSOLUTE MAXIMUM POWER RATING TEMPERATURE IS MEASURED. SELECT REPLY CODE 10AJ91 ALNYD /D/ 07ACID,ASCORBIC ASCORBIC ACID AN INDICATION OF WHETHER OR NOT ASCORBIC ACID IS INCLUDED IN THE ITEM. SELECT REPLY CODE 10AA49 ALNZD 18TYPE,SWEETENING SWEETENING TYPE INDICATES THE TYPE OF SWEETENING ADDED TO THE ITEM. SELECT REPLY CODE 10AH60 ALPAJ 10YIELD,BEVERAGE,UNIT PACKAGE UNIT PACKAGE BEVERAGE YIELD THE BEVERAGE YIELD PER PACKAGE UNIT WHEN MIXED AS RECOMMENDED. 1D AND 1B MODE REPLY12AG67 ALPBD /D/ 07ADDITIVE,FORTIFICATION FORTIFICATION ADDITIVE AN INDICATION OF WHETHER OR NOT THE ITEM HAS A FORTIFICATION ADDITIVE INCLUDED. SELECT REPLY CODE 10AA49 ALPCG 19COMPONENT AND QUANTITY COMPONENT AND QUANTITY THE NAME AND NUMBER OF COMPONENTS WHICH MAKE UP THE ITEM. FULL TEXT WRITE-IN 0 ALPDG /D/ 19CODE AND IDENTIFYING NUMBER,MANUFACTURER,COMPONENT COMPONENT MANUFACTURER CODE AND IDENTIFYING NUMBER THE NUMERIC CODE OF THE COMPONENT MANUFACTURER AND THE IDENTIFYING NUMBER OF THE COMPONENT. FULL TEXT WRITE-IN 0 ALPED /D/ 19SIMILARITY,COMPONENT COMPONENT SIMILARITY AN INDICATION OF WHETHER OR NOT THE COMPONENTS ARE MATCHED FOR PHYSICAL,ELECTRICAL,OR PERFORMANCE CHARACTERISTICS. SELECT REPLY CODE 10AH61 ALPFD /D/ 07FEATURE,ALKALINIZATION ALKALINIZATION FEATURE AN INDICATION OF WHETHER OR NOT AN ALKALINIZATION FEATURE IS INCLUDED ON THE ITEM. SELECT REPLY CODE 10AA49 ALPGD 19NAME,BRAND BRAND NAME THE BRAND NAME ASSIGNED BY THE MANUFACTURER. SELECT REPLY CODE 10AH62 ALPHD 18TYPE,ICE ICE TYPE INDICATES THE TYPE OF ICE. SELECT REPLY CODE 10AF11 ALPJD 18TYPE,PEDAL PEDAL TYPE INDICATES THE TYPE OF PEDAL. SELECT REPLY CODE 10AG89 ALPKJ /D/ 04HEIGHT,RETRACTED RETRACTED HEIGHT A MEASUREMENT FROM THE MOUNTING BASE TO THE TOP OF AN ITEM,WHEN RETRACTED,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 ALPLD 18TYPE,BRAKE BRAKE TYPE INDICATES THE TYPE OF BRAKE. SELECT REPLY CODE 10AG25 ALPMD 19FORM,ASSEMBLY ASSEMBLY FORM THE FORM OF ASSEMBLY IN WHICH THE ITEM IS SUPPLIED. SELECT REPLY CODE 10AE33 ALPND 18TYPE,FACE FACE TYPE INDICATES THE TYPE OF FACE PROVIDED. SELECT REPLY CODE 10AG89 ALPPD 07REVERSIBILITY,FACE,DOUBLE DOUBLE FACE REVERSIBILITY AN INDICATION OF WHETHER OR NOT THE FACE IS REVERSIBLE. SELECT REPLY CODE 10AF62 ALPQD 19CONSTRUCTION,FACE FACE CONSTRUCTION THE STRUCTURAL CHARACTERISTICS OF THE FACE. SELECT REPLY CODE 10AA39 ALPRA 12QUANTITY,ENTRYWAY,LIFT FORK LIFT FORK ENTRYWAY QUANTITY THE NUMBER OF ENTRYWAYS FOR A LIFT FORK. 1A MODE REPLY 0 ALPSD /D/ 07LIP,MATING,AIRCRAFT RAIL SYSTEM AIRCRAFT RAIL SYSTEM MATING LIP AN INDICATION OF WHETHER OR NOT A LIP FOR MATING WITH AIRCRAFT RAIL SYSTEM IS INCLUDED. SELECT REPLY CODE 10AA49 ALPTD 02DESIGN,SIDE,PLATFORM PLATFORM SIDE DESIGN THE DESIGN OF THE PLATFORM SIDE/S/. SELECT REPLY CODE 10AC46 ALPWD 18TYPE,CONSTRUCTION,SIDE PANEL SIDE PANEL CONSTRUCTION TYPE THE STRUCTURAL CHARACTERISTICS OF THE SIDE PANEL(S). SELECT REPLY CODE 10AA39 ALPXA 12QUANTITY,PANEL,SIDE SIDE PANEL QUANTITY THE NUMBER OF SIDE PANELS PROVIDED. 1A MODE REPLY 0 ALPYD /D/ 07FEATURE,POLARIZATION POLARIZATION FEATURE AN INDICATION OF WHETHER OR NOT A POLARIZATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ALPZD 19PLANE,POLARIZATION POLARIZATION PLANE AN INDICATION OF THE POLARIZATION PLANE OF THE ITEM. SELECT REPLY CODE 10AC60 ALQAJ A07REMOVABILITY AND QUANTITY,PANEL,SIDE SIDE PANEL REMOVABILITY AND QUANTITY AN INDICATION OF WHETHER OR NOT THE SIDE PANELS ARE REMOVABLE AND THE NUMBER. 1D AND 1A MODE REPLY11AC29 ALQBJ 04HEIGHT,INSIDE,BOX BOX INSIDE HEIGHT A MEASUREMENT TAKEN INSIDE A BOX FROM THE BOTTOM TO THE TOP,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 ALQCA 12QUANTITY,STRINGER STRINGER QUANTITY THE NUMBER OF STRINGERS PROVIDED. 1A MODE REPLY 0 ALQDB 10CAPACITY IN KILOWATTS,RATED,GENERATOR GENERATOR RATED CAPACITY IN KILOWATTS THE ELECTRICAL RATING FOR WHICH THE GENERATOR IS RATED,EXPRESSED IN KILOWATTS. 1B MODE REPLY 0 ALQEJ 04HEIGHT,STRINGER STRINGER HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE STRINGER,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 ALQFD 18TYPE,RING RING TYPE THE TYPE OF RING(S) USED ON THE ITEM. SELECT REPLY CODE 10AB47 ALQGD 18TYPE,CONTAINER CONTAINER TYPE INDICATES THE TYPE OF CONTAINER PROVIDED. SELECT REPLY CODE 10AF72 ALQHD /D/ 08LOCATION,DOOR,LOADING LOADING DOOR LOCATION INDICATES THE LOCATION OF THE LOADING DOOR(S). SELECT REPLY CODE 10AE46 ALQJD /D/ 08LOCATION,FEATURE,UNLOADING UNLOADING FEATURE LOCATION AN INDICATION OF THE LOCATION OF THE UNLOADING FEATURE. SELECT REPLY CODE 10AE46 ALQKD /D/ 07BOTTOM,SUMP SUMP BOTTOM AN INDICATION OF WHETHER OR NOT A SUMP BOTTOM IS INCLUDED. SELECT REPLY CODE 10AA49 ALQLD /D/ 07PLUG,DRAIN DRAIN PLUG AN INDICATION OF WHETHER OR NOT A DRAIN PLUG IS INCLUDED. SELECT REPLY CODE 10AA49 ALQMB 10DENSITY RATING DENSITY RATING AN INDICATION OF THE RATED DENSITY OF THE ITEM. 1B MODE REPLY 0 ALQNB 10TRANSMISSION RATING IN PERCENT,LIGHT LIGHT TRANSMISSION RATING IN PERCENT THE LIGHT TRANSMITTED THROUGH THE ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 ALQPD /D/ 07PLATFORM PLATFORM AN INDICATION OF WHETHER OR NOT A PLATFORM IS INCLUDED. SELECT REPLY CODE 10AA49 ALQQD 18TYPE FOR WHICH DESIGNED,EYEPIECE EYEPIECE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF EYEPIECE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AD71 ALQRD 18TYPE,HOOKUP,TRACK TRACK HOOKUP TYPE INDICATES THE TYPE OF TRACK HOOKUP FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AH64 ALQSJ 04DIAMETER,OUTSIDE,EYEPIECE EYEPIECE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE EYEPIECE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ALQTD /D/ 07VARIABILITY,DENSITY DENSITY VARIABILITY AN INDICATION OF WHETHER OR NOT THE DENSITY OF THE ITEM IS VARIABLE. SELECT REPLY CODE 10AH65 ALQWA 12QUANTITY,TRACK TRACK QUANTITY THE NUMBER OF TRACKS FURNISHED WITH THE ITEM. 1A MODE REPLY 0 ALQXD /D/ 09MATERIAL,TRACK TRACK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TRACK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ALQYD /D/ 09MATERIAL,SURFACE SURFACE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SURFACE OF THE ITEM IS FABRICATED. SELECT REPLY CODE 10AD09 ALQZD 02DESIGN,TRACK TRACK DESIGN THE BASIC DESIGN OF THE TRACK. SELECT REPLY CODE 10AE33 ALRAJ 04LENGTH,OVERALL,TRACK TRACK OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE TRACK. 2D AND 1B MODE REPLY21AA051AC20 ALRBJ 04WIDTH,OVERALL,TRACK TRACK OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TRACK,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALRCJ 10TRANSMISSION IN PERCENT,LIGHT,WHITE WHITE LIGHT TRANSMISSION IN PERCENT THE WHITE LIGHT TRANSMITTED,EXPRESSED IN PERCENT. 1D AND 1B MODE REPLY12AH66 ALRDD 19FACILITY,SUPPORT SUPPORT FACILITY THE MEANS TO SUPPORT OR ACCOMMODATE THE ITEM. SELECT REPLY CODE 10AA78 ALRED 18TYPE,TIRE TIRE TYPE INDICATES THE TYPE OF TIRE(S) PROVIDED. SELECT REPLY CODE 10AH67 ALRFJ 04LENGTH,OVERALL,VIEWING SURFACE VIEWING SURFACE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE VIEWING SURFACE. 2D AND 1B MODE REPLY21AA051AC20 ALRGJ 04WIDTH,OVERALL,VIEWING SURFACE VIEWING SURFACE OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE VIEWING SURFACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALRHJ 04DIAMETER,OVERALL,VIEWING SURFACE VIEWING SURFACE OVERALL DIAMETER A MEASUREMENT OF THE LARGEST STRAIGHT LINE ACROSS THE VIEWING SURFACE. 2D AND 1B MODE REPLY21AA051AC20 ALRJJ 04HEIGHT,OVERALL,VIEWING SURFACE VIEWING SURFACE OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE VIEWING SURFACE. 2D AND 1B MODE REPLY21AA051AC20 ALRKJ 04THICKNESS,OVERALL,VIEWING SURFACE VIEWING SURFACE OVERALL THICKNESS AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF THE VIEWING SURFACE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALRLH /D/ 09MATERIAL AND LOCATION,DECK DECK MATERIAL AND LOCATION THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE DECK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT,AND ITS LOCATION. 2D MODE REPLY 26AD092AE46 ALRMJ 04LENGTH,PLATFORM PLATFORM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE PLATFORM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALRNJ 04WIDTH,PLATFORM PLATFORM WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PLATFORM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALRPJ 10UNDERCLEARANCE,PLATFORM PLATFORM UNDERCLEARANCE A MEASUREMENT OF THE DISTANCE FROM THE SUPPORT TO THE UNDERSIDE OF THE PLATFORM. 2D AND 1B MODE REPLY21AA051AC20 ALRQD /D/ 07GASKET,TOP/BOTTOM TOP/BOTTOM GASKET AN INDICATION OF WHETHER OR NOT TOP AND/OR BOTTOM GASKETS ARE INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA49 ALRRD /D/ 07RING,LIFTING LIFTING RING AN INDICATION OF WHETHER OR NOT A LIFTING RING/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 ALRSJ 04LENGTH,FILTER FILTER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A FILTER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALRTJ 04WIDTH,FILTER FILTER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A FILTER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALRVL /D/ 16STYLE,NEW NEW STYLE MY NEW STYLE 1L MODE REPLY 0 ALRWJ 04DIAMETER,FILTER FILTER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FILTER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ALRXJ 04THICKNESS,FILTER FILTER THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE FILTER,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALRYJ /D/ 10PARALLELISM,SURFACE SURFACE PARALLELISM THE MAXIMUM ANGULAR DEVIATION OF LIGHT NORMALLY INCIDENT TO THE FILTER SURFACE. 1D AND 1B MODE REPLY12AH68 ALRZJ /D/ 04DIAMETER,OPENING,TOP TOP OPENING DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ALSAD /D/ 07HOOK,GRAB,CHAIN CHAIN GRAB HOOK AN INDICATION OF WHETHER OR NOT A CHAIN GRAB HOOK/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 ALSBJ 10SIZE,CHAIN CHAIN SIZE DESIGNATES THE SIZE OF THE CHAIN. 2D AND 1B MODE REPLY21AA051AC20 ALSCJ 10LOAD RATING,OPERATING,SAFE SAFE OPERATING LOAD RATING THE SAFE OPERATING LOAD FOR WHICH THE ITEM IS DESIGNED TO ACCOMMODATE. 2D AND 1B MODE REPLY22AB161AC20 ALSDD /D/ 07LEVER LEVER AN INDICATION OF WHETHER OR NOT A LEVER IS INCLUDED. SELECT REPLY CODE 10AA49 ALSEJ 04LENGTH,LEVER LEVER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE LEVER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALSFD /D/ 07ACCOMMODATION,BATTERY,INTERNAL INTERNAL BATTERY ACCOMMODATION AN INDICATION OF WHETHER OR NOT A FACILITY/IES/ TO ACCOMMODATE A BATTERY/IES/ IS INCLUDED. SELECT REPLY CODE 10AA49 ALSGA 12QUANTITY,SWIVEL SWIVEL QUANTITY THE NUMBER OF SWIVELS PROVIDED. 1A MODE REPLY 0 ALSHD /D/ 07SPRING,TAKE-UP TAKE-UP SPRING AN INDICATION OF WHETHER OR NOT A TAKE-UP SPRING IS INCLUDED. SELECT REPLY CODE 10AA49 ALSJJ 04HEIGHT,OVERALL,PLATFORM PLATFORM OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE PLATFORM. 2D AND 1B MODE REPLY21AA051AC20 ALSKD /D/ 07COUPLER,TOWING TOWING COUPLER AN INDICATION OF WHETHER OR NOT A TOWING COUPLER(S) IS INCLUDED. SELECT REPLY CODE 10AA49 ALSLD 19ORIGIN,PART,SKIN SKIN PART ORIGIN AN INDICATION OF THE ORIGIN OF THE SKIN PART. SELECT REPLY CODE 10AH69 ALSMG /D/ 10CAPACITY RATING,COMPONENT,MAJOR MAJOR COMPONENT CAPACITY RATING THE MAXIMUM CAPACITY FOR WHICH THE MAJOR COMPONENT IS RATED. FULL TEXT WRITE-IN 0 ALSND /D/ 07SET,GENERATOR,GASOLINE ENGINE DRIVEN GASOLINE ENGINE DRIVEN GENERATOR SET AN INDICATION OF WHETHER OR NOT A GASOLINE ENGINE DRIVEN GENERATOR SET IS INCLUDED. SELECT REPLY CODE 10AA49 ALSPB 10VOLTAGE RATING,GENERATOR GENERATOR VOLTAGE RATING THE ELECTRICAL VOLTAGE VALUE FOR WHICH THE GENERATOR IS RATED. 1B MODE REPLY 0 ALSQD /D/ 07FEATURE,BEVELED BEVELED FEATURE AN INDICATION OF WHETHER OR NOT A BEVELED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ALSRD 19PHASE,GENERATOR GENERATOR PHASE THE NUMBER OF ALTERNATING CURRENT PHASES OF THE GENERATOR. SELECT REPLY CODE 10AD02 ALSSB 10FREQUENCY RATING,GENERATOR GENERATOR FREQUENCY RATING THE CYCLES PER SECOND (HERTZ) OF THE GENERATOR ALTERNATING CURRENT. 1B MODE REPLY 0 ALSTD /D/ 19SOLVENT FOR WHICH DESIGNED SOLVENT FOR WHICH DESIGNED INDICATES THE TYPE OF SOLVENT WITH WHICH THE ITEM IS DESIGNED TO BE USED. SELECT REPLY CODE 10AF12 ALSUJ /D/ 04WIDTH,RAKE RAKE WIDTH THE WIDTH OF THE RAKE HEAD. 2D AND 1B MODE REPLY21AA051AC20 ALSVH /D/ 19TYPE,HOWITZER HOWITZER TYPE INDICATES THE TYPE OF HOWITZER. 2D MODE REPLY 23AK543AF07 ALSWA 19NUMBER,STRIP,COMMERCIAL COMMERCIAL STRIP NUMBER THE COMMERCIAL NUMBER USED TO IDENTIFY THE STRIP. 1A MODE REPLY 0 ALSXD /D/ 09MATERIAL,CYLINDER CYLINDER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CYLINDER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ALSYA 12QUANTITY,COMPARTMENT,CYLINDER CYLINDER COMPARTMENT QUANTITY THE NUMBER OF COMPARTMENTS INCORPORATED IN THE CYLINDER. 1A MODE REPLY 0 ALSZJ 04WIDTH,FACE,FLAT FLAT FACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PLANE SURFACE OF THE ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALTAJ 04DIAMETER,CYLINDER CYLINDER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CYLINDER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ALTBJ 04LENGTH,CYLINDER CYLINDER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CYLINDER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALTCJ 10OPERATING RPM PER CYCLE,CYLINDER CYLINDER OPERATING RPM PER CYCLE THE SPEED OF THE CYLINDER,EXPRESSED IN REVOLUTIONS PER MINUTE PER OPERATING CYCLE. 1D AND 1B MODE REPLY12AH70 ALTDD /D/ 09MATERIAL,CUSHIONING CUSHIONING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CUSHIONING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ALTED /D/ 07PUMP PUMP AN INDICATION OF WHETHER OR NOT A PUMP IS INCLUDED. SELECT REPLY CODE 10AA49 ALTFB 10PUMP RATING IN GPM PUMP RATING IN GPM THE RATED CAPACITY OF THE FLUID DELIVERED BY THE PUMP,EXPRESSED IN GALLONS PER MINUTE. 1B MODE REPLY 0 ALTGD /D/ 07TANK,SOLVENT SOLVENT TANK AN INDICATION OF WHETHER OR NOT A SOLVENT TANK IS INCLUDED. SELECT REPLY CODE 10AA49 ALTHA 12QUANTITY,TANK TANK QUANTITY THE NUMBER OF TANKS PROVIDED. 1A MODE REPLY 0 ALTJJ /D/ 10CAPACITY,TANK,WASH WASH TANK CAPACITY THE CAPACITY THAT THE WASH TANK WILL HOLD. 1D AND 1B MODE REPLY11AB10 ALTKJ 04DISTANCE BETWEEN OFFSET MOUNTING FACILITIES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN OFFSET MOUNTING FACILITIES NONE. 2D AND 1B MODE REPLY21AA051AC20 ALTLD 02DESIGN,USAGE,ELECTRICAL MOTOR ELECTRICAL MOTOR USAGE DESIGN INDICATES THE DESIGNED USE OF THE ELECTRIC MOTOR. SELECT REPLY CODE 10AH71 ALTMD 11METHOD,SUPPORT SUPPORT METHOD THE MEANS PROVIDED FOR SUPPORTING THE ITEM. SELECT REPLY CODE 10AH72 ALTND /D/ 09MATERIAL,SUPPORT SUPPORT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SUPPORT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ALTPD /D/ 07FEATURE,ABSORBENT ABSORBENT FEATURE AN INDICATION OF WHETHER OR NOT AN ABSORBENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ALTQD /D/ 07SEPARATOR,PAPER,ROLL ROLL PAPER SEPARATOR AN INDICATION OF WHETHER OR NOT A ROLL PAPER SEPARATOR(S) IS PROVIDED. SELECT REPLY CODE 10AB22 ALTRD 18TYPE,FILTER FILTER TYPE INDICATES THE TYPE OF FILTER USED WITH THE ITEM. SELECT REPLY CODE 10AH81 ALTSD 18TYPE,GRAIN GRAIN TYPE INDICATES THE TYPE OF GRAIN. SELECT REPLY CODE 10AH73 ALTTD 18TYPE,AGITATOR AGITATOR TYPE INDICATES THE TYPE OF AGITATOR. SELECT REPLY CODE 10AH74 ALTUJ /D/ 10EXCAVATOR WEIGHT EXCAVATOR WEIGHT RECOMMENDED OVERALL WEIGHT OF EXCAVATOR NEEDED TO HANDLE THE SIZE OF CUTTER-BUCKET 2D AND 1B MODE REPLY22AG671AC20 ALTVA 10CYCLES,MAXIMUM NUMBER OF MAXIMUM NUMBER OF CYCLES INDICATES THE MAXIMUM NUMBER OF TIMES AN ITEM CYCLES. 1A MODE REPLY 0 ALTWD 08LOCATION,LOADING LOADING LOCATION INDICATES THE LOCATION OF THE LOAD OPENING(S) ON THE ITEM. SELECT REPLY CODE 10AE46 ALTXD 11METHOD,EXTRACTION EXTRACTION METHOD THE MEANS USED FOR EXTRACTION. SELECT REPLY CODE 10AH75 ALTYD 19FINISH,DECORATIVE DECORATIVE FINISH AN ADDITIONAL PATTERN AND/OR FINISH OF THE SURFACE OF AN ITEM FOR APPEARANCE. SELECT REPLY CODE 10AA41 ALTZD /D/ 08LOCATION,FINISH,SUEDE SUEDE FINISH LOCATION INDICATES THE LOCATION OF THE NAPPED FINISH ON THE ITEM. SELECT REPLY CODE 10AE46 ALUAA 12PROCESSOR CORE QUANTITY PROCESSOR CORE QUANTITY THE NUMBER OF CORE INCLUDED IN THE PROCESSOR 1A MODE REPLY 0 ALUBD 15TYPE,MATERIAL,CELLULAR,FLEXIBLE FLEXIBLE CELLULAR MATERIAL TYPE THE TYPE OF FLEXIBLE CELLULAR MATERIAL AS SPECIFIED BY ASTM D1056. SELECT REPLY CODE 10AP01 ALUCD 15CLASS,MATERIAL,CELLULAR,FLEXIBLE FLEXIBLE CELLULAR MATERIAL CLASS THE CLASS OF FLEXIBLE CELLULAR MATERIAL AS SPECIFIED BY ASTM D1056. SELECT REPLY CODE 10AP01 ALUDD 15GRADE,MATERIAL,CELLULAR,FLEXIBLE FLEXIBLE CELLULAR MATERIAL GRADE THE GRADE OF FLEXIBLE CELLULAR MATERIAL AS SPECIFIED BY ASTM D1056. THE GRADE RATING REPRESENTS THE COMPRESSION DEFLECTION OR THE AMOUNT OF FORCE IN POUNDS PER SQUARE INCH TO DEFLECT THE SAMPLE 25 PER CENT OF ITS HEIGHT. SELECT REPLY CODE 10AP01 ALUEA 15CODE,UNIVERSAL MEDICAL DEVICE NOMENCLATURE SYSTEM UNIVERSAL MEDICAL DEVICE NOMENCLATURE SYSTEM CODE THE UNIVERSAL MEDICAL DEVICE NOMENCLATURE SYSTEM CODE FOR THIS ITEM. 1A MODE REPLY 0 ALUFJ /D/ 04LINK CLEARANCE DISTANCE LINK CLEARANCE DISTANCE A MEASUREMENT FROM THE TOP OF THE MOUNTING SCREW OR BOLT HEAD TO THE TOP INSIDE OF RING. 2D AND 1B MODE REPLY21AA051AC20 ALUGJ 04OVERALL BASE HEIGHT OVERALL BASE HEIGHT A MEASUREMENT FROM THE BOTTOM OF BASE TO THE TOP OF THE MOUNTING SCREW OR BOLT HEAD. 2D AND 1B MODE REPLY21AA051AC20 ALUHJ /D/ 04DISTANCE FROM BASE MOUNTING SURFACE TO TOP INSIDE OF RING DISTANCE FROM BASE MOUNTING SURFACE TO TOP INSIDE OF RING NONE 2D AND 1B MODE REPLY21AA051AC20 ALUJJ /D/ 04DISTANCE BETWEEN CENTERLINE OF MOUNTING HOLE(S) AND TOP OF RING DISTANCE BETWEEN CENTERLINE OF MOUNTING HOLE(S) AND TOP OF RING A MEASUREMENT FROM THE CENTERLINE OF THE BASE MOUNTING HOLE(S) AND TOP OF RING WHEN HORIZONTALLY ARTICULATED 90 DEGREES FROM THE CENTERLINE. 2D AND 1B MODE REPLY21AA051AC20 ALUKJ /D/ 04DISTANCE BETWEEN CENTERLINE OF MOUNTING HOLE(S) AND TOP INSIDE OF RING DISTANCE BETWEEN CENTERLINE OF MOUNTING HOLE(S) AND TOP INSIDE OF RING A MEASUREMENT OF THE SHORTEST DISTANCE BETWEEN MOUNTING HOLE(S) CENTERLINE AND TOP INSIDE EDGE OF RING WHEN HORIZONTALLY ARTICULATED 90 DEGREES FROM THE CENTERLINE. 2D AND 1B MODE REPLY21AA051AC20 ALULJ 04OVERALL WIDTH OF THE RING OVERALL WIDTH OF THE RING DISTANCE FROM OUTSIDE EDGE OF BASE TO OUTSIDE EDGE OF HORIZONTALLY ARTICULATED RING. 2D AND 1B MODE REPLY21AA051AC20 ALUMD 18VIEWER TYPE VIEWER TYPE INDICATES THE TYPE OF VIEWER. SELECT REPLY CODE 10AK95 ALUND 18OPTRONIC DEVICE TYPE OPTRONIC DEVICE TYPE INDICATES THE TYPE OF OPTRONIC DEVICE USED. SELECT REPLY CODE 10AD48 ALUQJ 04WIDTH ACCOMMODATED,ROTOR DISK ROTOR DISK WIDTH ACCOMMODATED A MEASUREMENT OF THE ALLOWANCE FOR THE THICKNESS OF THE ROTOR DISK, PERPENDICULAR TO THE DIAMETER. 2D AND 1B MODE REPLY21AA051AC20 ALURD /D/ 07INFORMATION,ALLERGEN ALLERGEN INFORMATION INDICATES A SUBSTANCE THAT MAY CAUSE AN ALLERGIC REACTION. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AL30 ALUSA 12QUANTITY,PISTON PISTON QUANTITY THE NUMBER OF PISTONS 1A MODE REPLY 0 ALUTD /D/ 18UNDERWEAR TYPE UNDERWEAR TYPE INDICATES THE TYPE OF UNDERWEAR SELECT REPLY CODE 10AH80 ALUUD 19USE FOR ANIMAL,INTENDED INTENDED USE FOR ANIMAL INDICATES THE PURPOSE OF THE ANIMAL. SELECT REPLY CODE 10AK54 ALUVG 19BREED BREED THE BREED OF THE ANIMAL. FULL TEXT WRITE-IN 0 ALUWD /D/ 18DAY CHANNEL TYPE DAY CHANNEL TYPE INDICATES THE TYPE OF DAY CHANNEL SELECT REPLY CODE 10AM07 ALUXD /D/ 18NIGHT CHANNEL TYPE NIGHT CHANNEL TYPE INDICATES THE TYPE OF NIGHT CHANNEL SELECT REPLY CODE 10AD48 ALUYJ 10NO LOAD SPEED IN SFPM NO LOAD SPEED IN SFPM THE SPEED AT WHICH AN ITEM CAN BE OPERATED UNDER A NO LOAD CONDITION,EXPRESSED IN SURFACE FEET PER MINUTE. 1D AND 1B MODE REPLY11AC20 ALUZG 10ROUND STOCK CUTTING CAPACITY ROUND STOCK CUTTING CAPACITY THE CUT CAPACITY FOR ROUND STOCK. FULL TEXT WRITE-IN 0 ALVAG 10RECTANGULAR STOCK CUTTING CAPACITY RECTANGULAR STOCK CUTTING CAPACITY THE CUT CAPACITY FOR RECTANGULAR STOCK. FULL TEXT WRITE-IN 0 ALVBJ /D/ 04SIZE FOR WHICH DESIGNED,CANISTER CANISTER SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE CANISTER FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY22AG671AC20 ALVCG 18TYPE AND SIZE ACCOMMODATED,NAIL NAIL TYPE AND SIZE ACCOMMODATED THE TYPE AND SIZE NAIL THAT IS COMPATIBLE WITH THE ITEM. FULL TEXT WRITE-IN 0 ALVDD 18TYPE,MAGAZINE MAGAZINE TYPE THE TYPE OF MAGAZINE INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AK95 ALVEB 04ANGLE IN DEG,MAGAZINE MAGAZINE ANGLE IN DEG THE ANGLE OF THE MAGAZINE EXPRESSED IN DEGREES. 1B MODE REPLY 0 ALVFJ /D/ 04JAW DEPTH,OUTSIDE OUTSIDE JAW DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE OUTSIDE JAW, IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 ALVGJ /D/ 04JAW DEPTH,INSIDE INSIDE JAW DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE INSIDE JAW, IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 ALVHD 01COLOR,DIAL FACE DIAL FACE COLOR THE HUE OR TINT OF THE DIAL FACE. SELECT REPLY CODE 10AD06 ALVJA /D/ 10FORCE IN POUNDS,CLAMPING CLAMPING FORCE IN POUNDS THE AMOUNT OF CLAMPING FORCE THAT CAN BE APPLIED TO AN ITEM. 1A MODE REPLY 0 ALVKD 11INITIATION METHOD,FIRING FIRING INITIATION METHOD THE MEANS USED BY THE ITEM TO INITIATE IGNITION OF THE SENSITIVE EXPLOSIVE. SELECT REPLY CODE 10AF48 ALVLJ /D/ 04WIDTH,SEALING SEALING WIDTH NONE 2D AND 1B MODE REPLY21AA051AC20 ALVMD 08SIDE,CONTROL CONTROL SIDE INDICATES THE LOCATION OF THE CONTROL IN RELATION TO THE ITEM. SELECT REPLY CODE 10AD07 ALVNA 10SIZE ACCOMMODATED,KINGPIN KINGPIN SIZE ACCOMMODATED THE SIZE OF THE KINGPIN,FIFTH WHEEL ACCOMMODATED BY THE PLATE,FIFTH WHEEL ASSEMBLY. 1A MODE REPLY 0 ALVPD 18SUPPORT TYPE,PHYSICAL PROGRAM PHYSICAL PROGRAM SUPPORT TYPE INDICATES THE TYPE OF PHYSICAL SUPPORT USED FOR STORING OR TRANSFERRING THE PROGRAM. SELECT REPLY CODE 10AP91 ALVQG 19AGREEMENT,LICENSE LICENSE AGREEMENT THE NAME, NUMBER AND DESCRIPTION OF LICENSE ABOUT THE PROGRAM. FULL TEXT WRITE-IN 0 ALVRJ A18TYPE,PROGRAM PROGRAM TYPE PROGRAM TYPE AND QUANTITY 1D AND 1A MODE REPLY12PT01 ALVSB 12LEVEL IN METERS PER SECOND SQUARED,VIBRATION VIBRATION LEVEL IN METERS PER SECOND SQUARED A NUMERIC VALUE INDICATING THE VIBRATION OUTPUT OF THE ITEM EXPRESSED IN METERS PER SECOND SQUARED. 1B MODE REPLY 0 ALVTG /D/ 15NUMBER,PROTECTION,SEAL SEAL PROTECTION NUMBER THE RATE AND DEGREE OF SEAL PROTECTION AGAINST DUST AND WATER INTRUSION. FULL TEXT WRITE-IN 0 ALVUD /D/ 08LOCATION,GUIDED MISSILE GUIDED MISSILE LOCATION INDICATES THE LOCATION OF THE ITEM ON THE GUIDED MISSILE SELECT REPLY CODE 10AJ54 ALVVJ 10CAPACITY,TOWING TOWING CAPACITY THE MAXIMUM ALLOWABLE WEIGHT THE VEHICLE CAN SAFELY PULL. 1D AND 1B MODE REPLY12AG67 ALVWD /D/ 10CAPACITY,PAYLOAD PAYLOAD CAPACITY MAXIMUM WEIGHT THAT THE ITEM CAN CARRY OR PULL. SELECT REPLY CODE 10AG67 ALVXA 19POSITIONS,ADJUSTMENT,JAW JAW ADJUSTMENT POSITIONS THE NUMBER OF POSITIONS TO WHICH THE JAW CAN BE ADJUSTED. 1A MODE REPLY 0 ALVYJ 10PRESSURE,RETURN RETURN PRESSURE THE AMOUNT OF PRESSURE BEING RETUNED TO THE OUTLET VALVES/PORTS. 1D AND 1B MODE REPLY12AG20 ALVZD /D/ 09MATERIAL,PRODUCT PRODUCT MATERIAL DESIGNATES THE MATERIAL THE ITEM USES TO PRODUCE A PRODUCT. SELECT REPLY CODE 10MA01 ALWAD /D/ 07TUB,EXTRACTION,SEPARATE SEPARATE EXTRACTION TUB AN INDICATION OF WHETHER OR NOT A SEPARATE TUB FOR EXTRACTION IS FURNISHED. SELECT REPLY CODE 10AA55 ALWBD /D/ 18TYPE,DRAIN DRAIN TYPE INDICATES THE TYPE OF DRAIN. SELECT REPLY CODE 10AA96 ALWCD 19CONTOUR,SKIN SKIN CONTOUR AN INDICATION OF THE PROCESS USED TO OBTAIN THE FINISHED CONTOUR OF THE ITEM. SELECT REPLY CODE 10AJ07 ALWDD 03DESIGNATION,TRADE TRADE DESIGNATION THE DESIGNATION BY WHICH THE ITEM IS IDENTIFIED THROUGHOUT INDUSTRY. SELECT REPLY CODE 10AJ09 ALWEJ 10SIZE SIZE A MEASUREMENT OF THE TOTAL SURFACE OF AN ITEM. 2D AND 1B MODE REPLY21AC511AC20 ALWFD 11METHOD,UNLOADING UNLOADING METHOD THE MEANS BY WHICH THE ITEM IS UNLOADED. SELECT REPLY CODE 10AH76 ALWGD /D/ 07PARTITION,HORIZONTAL HORIZONTAL PARTITION AN INDICATION OF WHETHER OR NOT A HORIZONTAL PARTITION/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 ALWHJ 04LENGTH,INSIDE,CYLINDER CYLINDER INSIDE LENGTH A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF THE CYLINDER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALWJJ 04DIAMETER,INSIDE,CYLINDER CYLINDER INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CYLINDER,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ALWKJ 04DIAMETER,INSIDE,BASKET BASKET INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BASKET,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ALWLD /D/ 07FEATURE,CIRCULATION CIRCULATION FEATURE AN INDICATION OF WHETHER OR NOT A CIRCULATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ALWMD /D/ 01COLOR,PRODUCT PRODUCT COLOR DESIGNATES THE COLOR OF THE PRODUCT PRODUCED BY THE ITEM. SELECT REPLY CODE 10AD06 ALWNJ /D/ 10HARDNESS RATING AND LOCATION,NONMETALLIC NONMETALLIC HARDNESS RATING AND LOCATION A NUMERIC VALUE USED IN CONJUNCTION WITH A HARDNESS RATING SCALE DESIGNATING THE SPECIFIC NONMETALLIC HARDNESS RATING AND ITS LOCATION. 3D AND 1B MODE REPLY31AC202AC263AJ91 ALWPD 08LOCATION,CASEHARDENED CASEHARDENED LOCATION INDICATES THE LOCATION OF AN ITEM WHICH IS CASEHARDENED. SELECT REPLY CODE 10AJ91 ALWQD /D/ 19FUNCTION,CONTROLLED,MANUALLY MANUALLY CONTROLLED FUNCTION AN INDICATION OF THE FUNCTION/S/ WHICH IS MANUALLY CONTROLLED. SELECT REPLY CODE 10AC58 ALWRJ 04RADIUS,CORNER,FIRST END FIRST END CORNER RADIUS THE MEASURED DISTANCE FROM A FIXED POINT TO A VARIABLE POINT ON A CURVE OR CURVED SURFACE. 2D AND 1B MODE REPLY21AA051AC20 ALWSJ 04RADIUS,CORNER,SECOND END SECOND END CORNER RADIUS THE MEASURED DISTANCE FROM A FIXED POINT TO A VARIABLE POINT ON A CURVE OR CURVED SURFACE. 2D AND 1B MODE REPLY21AA051AC20 ALWTD /D/ 19FUNCTION,CONTROLLED,SEMIAUTOMATIC SEMIAUTOMATIC CONTROLLED FUNCTION AN INDICATION OF THE FUNCTION/S/ WHICH IS SEMIAUTOMATICALLY CONTROLLED. SELECT REPLY CODE 10AC58 ALWUJ 04THICKNESS,JAW JAW THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A JAW,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALWVG 10DISSIPATION,HEAT HEAT DISSIPATION THE MAXIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY AN ITEM WHEN MOUNTED ON A CHASSIS OR METAL PLATE. EXPRESSED IN WATTS OR HORSEPOWER. FULL TEXT WRITE-IN 0 ALWWD /D/ 19FUNCTION,CONTROLLED,AUTOMATIC AUTOMATIC CONTROLLED FUNCTION AN INDICATION OF THE FUNCTION/S/ WHICH IS AUTOMATICALLY CONTROLLED. SELECT REPLY CODE 10AC58 ALWXD 18TYPE,CONTROL,BRAKE BRAKE CONTROL TYPE THE MEANS BY WHICH THE BRAKE IS CONTROLLED. SELECT REPLY CODE 10AG25 ALWYD /D/ 07DEVICE,LOCKING,BRAKE BRAKE LOCKING DEVICE AN INDICATION OF WHETHER OR NOT A BRAKE LOCKING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 ALWZB 10VOLTAGE RATING,ELEMENT,HEATING HEATING ELEMENT VOLTAGE RATING THE VOLTAGE VALUE FOR WHICH THE HEATING ELEMENT IS RATED. 1B MODE REPLY 0 ALXAD /D/ 07CONTROL,TEMP,THERMOSTAT THERMOSTAT TEMP CONTROL AN INDICATION OF WHETHER OR NOT A THERMOSTAT TEMPERATURE CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 ALXBD 18TYPE,EXTRACTION,CENTRIFUGAL CENTRIFUGAL EXTRACTION TYPE INDICATES THE TYPE OF CENTRIFUGAL EXTRACTION. SELECT REPLY CODE 10AH77 ALXCJ /D/A08LOCATION AND QUANTITY,CHARACTERISTIC,DESIGN DESIGN CHARACTERISTIC LOCATION AND QUANTITY INDICATES THE LOCATION OF THE DESIGN CHARACTERISTIC(S) ON THE ITEM,AND THE NUMBER OF EACH. 3D AND 1A MODE REPLY32AH782AH463AJ91 ALXDA 12QUANTITY,SET,CONTAINER CONTAINER SET QUANTITY THE NUMBER OF CONTAINER SETS IN THE ITEM. 1A MODE REPLY 0 ALXEA 12QUANTITY,BUCK BUCK QUANTITY THE NUMBER OF BUCKS FURNISHED WITH THE ITEM. 1A MODE REPLY 0 ALXFD 02DESIGN,STRUCTURAL STRUCTURAL DESIGN THE BASIC STRUCTURE OF THE ITEM. SELECT REPLY CODE 10AH79 ALXGD /D/ 07CYLINDER,HEATED,STEAM STEAM HEATED CYLINDER AN INDICATION OF WHETHER OR NOT A STEAM HEATED CYLINDER IS INCLUDED. SELECT REPLY CODE 10AA49 ALXHD 18TYPE,BUCK BUCK TYPE INDICATES THE TYPE OF BUCK. SELECT REPLY CODE 10AH80 ALXJJ /D/A08LOCATION AND QUANTITY,LOOP,END END LOOP LOCATION AND QUANTITY INDICATES THE LOCATION AND NUMBER OF END LOOP(S) ON THE ITEM. 1D AND 1A MODE REPLY12AE46 ALXKA 12QUANTITY,LOOP,INTERMEDIATE INTERMEDIATE LOOP QUANTITY THE NUMBER OF INTERMEDIATE LOOPS PROVIDED. 1A MODE REPLY 0 ALXLJ 04LENGTH,BUCK BUCK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BUCK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALXMD 11METHOD,ROTATION,CARRIAGE CARRIAGE ROTATION METHOD THE MEANS BY WHICH THE CARRIAGE IS ROTATED. SELECT REPLY CODE 10AA77 ALXND 18TYPE,VACUUM VACUUM TYPE INDICATES THE TYPE OF VACUUM PROVIDED FOR USE WITH THE ITEM. SELECT REPLY CODE 10AA94 ALXPD /D/ 07PLATE,PRESS,HEAD HEAD PRESS PLATE AN INDICATION OF WHETHER OR NOT A HEAD PRESS PLATE IS INCLUDED. SELECT REPLY CODE 10AA49 ALXQD /D/ 07STEAMER,SHOULDER SHOULDER STEAMER AN INDICATION OF WHETHER OR NOT A SHOULDER STEAMER IS INCLUDED. SELECT REPLY CODE 10AA49 ALXRD /D/ 07BOILER,STEAM STEAM BOILER AN INDICATION OF WHETHER OR NOT A STEAM BOILER IS INCLUDED. SELECT REPLY CODE 10AA49 ALXSJ /D/ 10CAPACITY,RATED,FILTER FILTER RATED CAPACITY THE MEASURED CAPACITY OF THE FILTER. 1D AND 1B MODE REPLY11AB10 ALXTD /D/ 19DEVICE,LIFTING,LID LID LIFTING DEVICE AN INDICATION OF THE DEVICE USED FOR LIFTING THE LID. SELECT REPLY CODE 10AH76 ALXUJ /D/ 10HEIGHT,BED BED HEIGHT BED HEIGHT 2D AND 1B MODE REPLY21AA051AC20 ALXVD /D/ 10RATING,SPEED,OFF ROAD OFF ROAD SPEED RATING OFF ROAD SPEED RATING SELECT REPLY CODE 10AA34 ALXWD 18TYPE,PRINTER PRINTER TYPE INDICATES THE TYPE OF DEVICE USED FOR FORMING PRINT. SELECT REPLY CODE 10AE15 ALXXD /D/ 11METHOD,OPERATING,SCREEN SCRAPING/BACKWASHING DEVICE SCREEN SCRAPING/BACKWASHING DEVICE OPERATING METHOD THE MEANS OF OPERATING THE SCREEN SCRAPING/BACKWASHING DEVICE. SELECT REPLY CODE 10AH82 ALXYG /D/ 04SPACING,HOLE,MOUNTING MOUNTING HOLE SPACING THE SPACING BETWEEN THE MOUNTING HOLES. FULL TEXT WRITE-IN 0 ALXZG 02DESIGN,USAGE,SPECIFIC SPECIFIC USAGE DESIGN INDICATES THE DESIGNED USE OF THE ITEM. FULL TEXT WRITE-IN 0 ALYAD /D/ 19REFUSE FOR WHICH DESIGNED REFUSE FOR WHICH DESIGNED THE KIND OF REFUSE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AH21 ALYBD 18TYPE,DEVICE,OPERATION OPERATION DEVICE TYPE INDICATES THE TYPE OF DEVICE BY WHICH THE ITEM IS OPERATED. SELECT REPLY CODE 10AH83 ALYCD 18TYPE,CONTROL,OPERATING OPERATING CONTROL TYPE INDICATES THE TYPE OF DEVICE WHICH CONTROLS THE OPERATION OF THE ITEM. SELECT REPLY CODE 10AH83 ALYDD /D/ 18TYPE,SYSTEM,CALL CALL SYSTEM TYPE INDICATES THE TYPE OF CALL SYSTEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AH84 ALYED /D/ 07FEATURE,REVERSIBILITY,ROTATION ROTATION REVERSIBILITY FEATURE AN INDICATION OF WHETHER OR NOT A REVERSIBLE ROTATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ALYFJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR AND LOCATION THREAD SIZE AND SERIES/TYPE DESIGNATOR AND LOCATION DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE,AND THE THREAD LOCATION. 2D AND 1A MODE REPLY22AH063AJ91 ALYGD /D/ 18TYPE,FACILITY,CONVEYING,GARMENT GARMENT CONVEYING FACILITY TYPE INDICATES THE TYPE OF CONVEYING FACILITY PROVIDED TO CONTAIN OR HOLD THE GARMENT(S). MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AH85 ALYHA /D/ 12QUANTITY,BIN BIN QUANTITY THE NUMBER OF BINS PROVIDED. 1A MODE REPLY 0 ALYJJ /D/ 04LENGTH,OVERALL,BIN BIN OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BIN. 2D AND 1B MODE REPLY21AA051AC20 ALYKJ /D/ 04WIDTH,OVERALL,BIN BIN OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BIN,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALYLJ /D/ 04DEPTH,OVERALL,BIN BIN OVERALL DEPTH AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF THE BIN,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 ALYMA /D/ 12QUANTITY,COMPARTMENT,BIN BIN COMPARTMENT QUANTITY THE NUMBER OF COMPARTMENTS IN THE BIN. 1A MODE REPLY 0 ALYND /D/ 18TYPE,HOLE,FLANGE MOUNTING FLANGE MOUNTING HOLE TYPE INDICATES THE TYPE OF HOLE(S) PROVIDED ON THE FLANGE TO FACILITATE MOUNTING. SELECT REPLY CODE 10AB68 ALYPD 02DESIGN,LEVEL,FLOOR FLOOR LEVEL DESIGN THE DESIGN OF THE FLOOR LEVEL OF THE ITEM. SELECT REPLY CODE 10AH86 ALYQG 19TITLE,DOCUMENT DOCUMENT TITLE THE NAME DESIGNATION OF THE WRITTEN OR PRINTED DOCUMENT. FULL TEXT WRITE-IN 0 ALYRD /D/ 19KEY,MUSIC MUSIC KEY THE KEY IN WHICH THE MUSIC IS PLAYED. SELECT REPLY CODE 10AH87 ALYSJ /D/ 10CAPACITY,TANK,RINSE RINSE TANK CAPACITY THE CAPACITY THAT THE RINSE TANK WILL HOLD. 1D AND 1B MODE REPLY11AB10 ALYTD 11METHOD,HEATING,CHEST CHEST HEATING METHOD THE MEANS BY WHICH THE CHEST IS HEATED. SELECT REPLY CODE 10AA94 ALYUD /D/ 10VISCOSITY RATING VISCOSITY RATING INTERNAL FRICTION OF A MOVING LIQUID SELECT REPLY CODE 10AB44 ALYVB /D/ 10MIXING RATIO MIXING RATIO AMOUNT OF ONE SUBSTANCE IN RELATION TO ANOTHER 1B MODE REPLY 0 ALYWJ /D/ 10CAPACITY,TANK,FUEL FUEL TANK CAPACITY THE CAPACITY OF FUEL THE TANK WILL HOLD. 1D AND 1B MODE REPLY11AB10 ALYXL 16STYLE,STEM STEM STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE STEM. 1L MODE REPLY 0 ALYYJ 04WIDTH,BUCK BUCK WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BUCK,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ALYZD /D/ 07GROOVE,RELIEF,CARBON CARBON RELIEF GROOVE AN INDICATION OF WHETHER OR NOT A GROOVE FOR RELIEF OF CARBON ACCUMULATION IS INCLUDED. SELECT REPLY CODE 10AA49 ALZAD /D/ 19FABRIC,BUCK BUCK FABRIC THE FABRIC FOR WHICH THE BUCK IS DESIGNED. SELECT REPLY CODE 10AD09 ALZBJ 04RADIUS,NECK NECK RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ALZCJ /D/ 04DIAMETER,HOLE,NECK NECK HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ALZDJ 04LENGTH,STEM STEM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A STEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ALZEJ 04DIAMETER,STEM STEM DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ALZFJ 04DISTANCE FROM MINOR DIAMETER TO STEM END DISTANCE FROM MINOR DIAMETER TO STEM END NONE. 2D AND 1B MODE REPLY21AA051AC20 ALZGJ 04DISTANCE FROM GROOVE TO STEM END DISTANCE FROM GROOVE TO STEM END NONE. 2D AND 1B MODE REPLY21AA051AC20 ALZHJ 04DISTANCE FROM FIRST GROOVE TO STEM END DISTANCE FROM FIRST GROOVE TO STEM END NONE. 2D AND 1B MODE REPLY21AA051AC20 ALZJJ 04DISTANCE FROM SECOND GROOVE TO STEM END DISTANCE FROM SECOND GROOVE TO STEM END NONE. 2D AND 1B MODE REPLY21AA051AC20 ALZKJ 04DISTANCE FROM THIRD GROOVE TO STEM END DISTANCE FROM THIRD GROOVE TO STEM END NONE. 2D AND 1B MODE REPLY21AA051AC20 ALZLJ 04DIAMETER,GROOVE,FIRST FIRST GROOVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ALZMD /D/ 19MARKING,TEMPO,METRONOME METRONOME TEMPO MARKING THE SPEED AT WHICH THE MUSIC IS TO BE PLAYED AS INDICATED BY A MECHANICAL TIMING DEVICE. SELECT REPLY CODE 10AH88 ALZNJ 04DIAMETER,GROOVE,SECOND SECOND GROOVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ALZPJ 04DIAMETER,GROOVE,THIRD THIRD GROOVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ALZQJ 04WIDTH,GROOVE,FIRST FIRST GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ALZRJ 04WIDTH,GROOVE,SECOND SECOND GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ALZSJ 04WIDTH,GROOVE,THIRD THIRD GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ALZTJ 04DISTANCE FROM SLOT TO STEM END DISTANCE FROM SLOT TO STEM END NONE. 2D AND 1B MODE REPLY21AA051AC20 ALZUD /D/ 10STATIC PRESSURE STATIC PRESSURE PRESSURE EXERTED BY A STILL GAS OR LIQUID SELECT REPLY CODE 10AN71 ALZVD /D/ 19POSITION,MOUNTING,ARMREST ARMREST MOUNTING POSITION THE INSTALLED POSITION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AM84 ALZWD /D/ 19TEMPO TEMPO AN INDICATION OF THE TEMPO AT WHICH THE MUSIC IS PLAYED. SELECT REPLY CODE 10AH89 ALZXJ 04RADIUS,SLOT SLOT RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ALZYJ 04DISTANCE FROM HOLE CENTER TO STEM END DISTANCE FROM HOLE CENTER TO STEM END NONE. 2D AND 1B MODE REPLY21AA051AC20 ALZZJ 04DIAMETER,LARGEST,MUSHROOM END MUSHROOM END LARGEST DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMAAJ 04WIDTH,FLATTED FLATTED WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMABD /D/ 19METER METER THE TIME SIGNATURE THAT INDICATES THE RHYTHMICAL PATTERN OF NOTE VALUES,ACCENTS,AND BEATS PER MEASURE IN MUSIC. SELECT REPLY CODE 10AH90 AMACA /D/ 12QUANTITY,PART,MUSICAL MUSICAL PART QUANTITY THE NUMBER OF MUSICAL PARTS. 1A MODE REPLY 0 AMADJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,STUD,FIRST END FIRST END STUD THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE FIRST END STUD. 1D AND 1A MODE REPLY12AH06 AMAEG 19MATTER,SUBJECT SUBJECT MATTER AN INDICATION OF THE INFORMATION RELATED IN THE BOOK,MANUAL,OR SHEET BEING DESCRIBED. FULL TEXT WRITE-IN 0 AMAFD /D/ 07LIST,PARTS,SPARE SPARE PARTS LIST AN INDICATION OF WHETHER OR NOT A SPARE PARTS LIST IS INCLUDED. SELECT REPLY CODE 10AA49 AMAGD /D/ 07LIST,PRICE PRICE LIST AN INDICATION OF WHETHER OR NOT A PRICE LIST IS INCLUDED. SELECT REPLY CODE 10AA49 AMAJA /D/ 12QUANTITY,STUD,FIRST END FIRST END STUD QUANTITY THE NUMBER OF STUDS PROVIDED ON THE FIRST END. 1A MODE REPLY 0 AMAKG 19AUTHOR AUTHOR THE NAME OF THE PERSON OR PREPARING GROUP WRITING OR CREATING THE WORK. FULL TEXT WRITE-IN 0 AMALA 12QUANTITY,HOLE,PUNCHED PUNCHED HOLE QUANTITY THE NUMBER OF PUNCHED HOLES PROVIDED. 1A MODE REPLY 0 AMAMJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,STUD,SECOND END SECOND END STUD THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE SECOND END STUD. 1D AND 1A MODE REPLY12AH06 AMANA /D/ 12QUANTITY,STUD,SECOND END SECOND END STUD QUANTITY THE NUMBER OF STUDS PROVIDED ON THE SECOND END STUD. 1A MODE REPLY 0 AMAPA 19DATE,PUBLICATION PUBLICATION DATE THE DATE OR YEAR IN WHICH THE ITEM WAS MADE AVAILABLE. 1A MODE REPLY 0 AMAQD 19IDENTIFICATION,EDITION EDITION IDENTIFICATION THE TERMINOLOGY USED TO IDENTIFY A PARTICULAR EDITION. SELECT REPLY CODE 10AH91 AMARA 19NUMBER,PRINTING,REVISED EDITION REVISED EDITION PRINTING NUMBER THE NUMBER OF THE SPECIFIC PRINTING BY WHICH THE TEXT IS REVISED. 1A MODE REPLY 0 AMASG 19IDENTIFICATION,VOLUME VOLUME IDENTIFICATION THE NUMBER OR OTHER TERMINOLOGY THAT IDENTIFIES A SPECIFIC VOLUME/S/. FULL TEXT WRITE-IN 0 AMATG 19PUBLISHER PUBLISHER THE COMPANY OR OTHER GROUP THAT ISSUES THE ITEM. FULL TEXT WRITE-IN 0 AMAWG 19ADDRESS,PUBLISHER PUBLISHER ADDRESS THE ADDRESS OF THE PUBLISHER. FULL TEXT WRITE-IN 0 AMAXD /D/ 19FINISH,SURFACE,HUB OUTSIDE MACHINED HUB OUTSIDE MACHINED SURFACE FINISH AN ADDITIONAL FINISHING PROCESS BY WHICH THE OUTER PERIPHERY OF A HUB IS ALTERED. SELECT REPLY CODE 10AA41 AMAYD 19LANGUAGE,NATIONAL NATIONAL LANGUAGE THE LANGUAGE IN WHICH THE ITEM IS WRITTEN OR PREPARED. SELECT REPLY CODE 10AH92 AMAZD 19FEATURE,BINDING BINDING FEATURE AN INDICATION OF THE BINDING FEATURE(S) OF THE ITEM. SELECT REPLY CODE 10AH93 AMBAJ 04LENGTH FROM UNIVERSAL JOINT SPIDER CENTERLINE TO HUB END LENGTH FROM UNIVERSAL JOINT SPIDER CENTERLINE TO HUB END THE DISTANCE FROM THE CENTERLINE OF THE UNIVERSAL JOINT SPIDER TO THE HUB END,MEASURED ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS OF THE HUB. 2D AND 1B MODE REPLY21AA051AC20 AMBBJ 04LENGTH,OUTSIDE,MACHINED SURFACE FINISH,HUB HUB MACHINED SURFACE FINISH OUTSIDE LENGTH THE OUTSIDE LENGTH OF THE MACHINED SURFACE FINISH MEASURED ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS OF THE HUB. 2D AND 1B MODE REPLY21AA051AC20 AMBCD /D/ 07INDEX,THUMB THUMB INDEX AN INDICATION OF WHETHER OR NOT A THUMB INDEX IS INCLUDED. SELECT REPLY CODE 10AA49 AMBDD /D/ 18TYPE,HOLE,HUB SECURING HUB SECURING HOLE TYPE INDICATES THE TYPE OF SECURING HOLE(S) PROVIDED ON THE HUB. SELECT REPLY CODE 10AB68 AMBED 18TYPE,VERSION VERSION TYPE INDICATES THE TYPE OF VERSION. SELECT REPLY CODE 10AH94 AMBFJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR AND LOCATION,HOLE,SECURING SECURING HOLE THREAD SIZE AND SERIES/TYPE DESIGNATOR AND LOCATION DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE SECURING HOLE AND THE THREAD LOCATION. 2D AND 1A MODE REPLY22AH063AJ91 AMBGJ 04DIAMETER,HOLE,SECURING,UNTHREADED UNTHREADED SECURING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED SECURING HOLE,AND TERMINATES ON THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMBHD 19INTERVAL,ISSUE ISSUE INTERVAL AN INDICATION OF THE REGULARITY OF ISSUE. SELECT REPLY CODE 10AH95 AMBJG 19DATE,REVISION REVISION DATE AN INDICATION OF THE DATE THE ITEM WAS REVISED. FULL TEXT WRITE-IN 0 AMBKD /D/ 08LOCATION,HOLE,HUB SECURING HUB SECURING HOLE LOCATION INDICATES THE LOCATION OF THE HUB SECURING HOLE/S/. SELECT REPLY CODE 10AA97 AMBLJ /D/ 04LENGTH FROM UNIVERSAL JOINT SPIDER CENTERLINE TO FLANGE OUTER FACE LENGTH FROM UNIVERSAL JOINT SPIDER CENTERLINE TO FLANGE OUTER FACE THE MEASURED DISTANCE FROM THE UNIVERSAL JOINT SPIDER CENTERLINE TO THE FLANGE OUTER FACE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 AMBMJ /D/ 04LENGTH,ARM,SPIDER SPIDER ARM LENGTH THE DISTANCE BETWEEN THE TRUNNION FACES ON THE SAME VERTICAL OR HORIZONTAL PLANE. 2D AND 1B MODE REPLY21AA051AC20 AMBND /D/ 07ILLUSTRATION ILLUSTRATION AN INDICATION OF WHETHER OR NOT ILLUSTRATIONS ARE INCLUDED. SELECT REPLY CODE 10AA49 AMBPD /D/ 18TYPE,BEARING,SPIDER SPIDER BEARING TYPE INDICATES THE TYPE OF SPIDER BEARING. SELECT REPLY CODE 10AH96 AMBQD /D/ 14SHAPE,RETAINER RETAINER SHAPE THE PHYSICAL CONFIGURATION OF THE RETAINER. SELECT REPLY CODE 10AD07 AMBRD /D/ 07DETACHABILITY,COUPLING,FIRST END FIRST END COUPLING DETACHABILITY AN INDICATION OF WHETHER OR NOT THE FIRST END COUPLING CAN BE DETACHED FROM THE ITEM. SELECT REPLY CODE 10AH97 AMBSD /D/ 18TYPE,COUPLING,FIRST END FIRST END COUPLING TYPE INDICATES THE TYPE OF COUPLING FURNISHED ON THE FIRST END. SELECT REPLY CODE 10AH98 AMBTD /D/ 07DETACHABILITY,COUPLING,SECOND END SECOND END COUPLING DETACHABILITY AN INDICATION OF WHETHER OR NOT THE SECOND END COUPLING CAN BE DETACHED FROM THE ITEM. SELECT REPLY CODE 10AH97 AMBWD /D/ 18TYPE,COUPLING,SECOND END SECOND END COUPLING TYPE INDICATES THE TYPE OF COUPLING FURNISHED ON THE SECOND END. SELECT REPLY CODE 10AH98 AMBXD /D/ 11METHOD,GENERATING,HEAT HEAT GENERATING METHOD THE MEANS BY WHICH THE HEAT IS GENERATED. PLEASE USE MRC AYTH IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA93 AMBYJ /D/ 04LENGTH,COUPLING,SECOND END SECOND END COUPLING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SECOND END COUPLING. 2D AND 1B MODE REPLY21AA051AC20 AMBZJ /D/ 04DIAMETER,OUTSIDE,FIRST END BEARING SLEEVE FIRST END BEARING SLEEVE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FIRST END BEARING SLEEVE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 AMCAJ 04LENGTH,SLEEVE SLEEVE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SLEEVE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AMCBJ /D/ 04DIAMETER,OUTSIDE,SECOND END BEARING SLEEVE SECOND END BEARING SLEEVE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SECOND END BEARING SLEEVE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMCCJ /D/ 04LENGTH,SLEEVE,SECOND END BEARING SECOND END BEARING SLEEVE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SECOND END BEARING SLEEVE. 2D AND 1B MODE REPLY21AA051AC20 AMCDJ 04DIAMETER,OUTSIDE,INTERMEDIATE BEARING SLEEVE INTERMEDIATE BEARING SLEEVE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INTERMEDIATE BEARING SLEEVE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMCEJ 04LENGTH,SLEEVE,INTERMEDIATE BEARING INTERMEDIATE BEARING SLEEVE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE INTERMEDIATE BEARING SLEEVE. 2D AND 1B MODE REPLY21AA051AC20 AMCFD /D/ 08LOCATION,USAGE USAGE LOCATION INDICATES THE LOCATION AT WHICH THE ITEM IS TO BE USED. SELECT REPLY CODE 10AE46 AMCGD /D/ 19SECTION,SHAFT SHAFT SECTION AN INDICATION OF THE VARIOUS SECTIONS OF THE SHAFT. SELECT REPLY CODE 10AH99 AMCHD 18TYPE,PASTE,FOOD FOOD PASTE TYPE INDICATES THE TYPE OF FOOD PASTE. SELECT REPLY CODE 10AE92 AMCJD 18TYPE,FLOUR FLOUR TYPE INDICATES THE TYPE OF FLOUR. SELECT REPLY CODE 10AE92 AMCKA 12QUANTITY,BLOCK,TACKLE TACKLE BLOCK QUANTITY THE NUMBER OF TACKLE BLOCKS PROVIDED. 1A MODE REPLY 0 AMCLD 18TYPE,BLOCK BLOCK TYPE INDICATES THE TYPE OF BLOCK. SELECT REPLY CODE 10AE90 AMCMJ 04DISTANCE FROM END TO FLAT,FIRST END FIRST END DISTANCE FROM END TO FLAT NONE. 2D AND 1B MODE REPLY21AA051AC20 AMCNL 16STYLE,LOCKING LOCKING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM. 1L MODE REPLY 0 AMCPJ 04TAPER,END,FIRST FIRST END TAPER THE AMOUNT OF FIRST END TAPER PER MEASUREMENT SCALE. 3D AND 1B MODE REPLY31AA051AC201AB39 AMCQA 12QUANTITY,SHEAVE SHEAVE QUANTITY THE NUMBER OF SHEAVES PROVIDED. 1A MODE REPLY 0 AMCRJ 04DIAMETER,MAJOR,FIRST END TAPER FIRST END TAPER MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CIRCULAR CROSS SECTION OF THE FIRST END TAPERED PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMCSJ 04LENGTH,TAPER,FIRST END FIRST END TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMCTD 18TYPE,ACCOMMODATED,TACKLE TACKLE ACCOMMODATED TYPE INDICATES THE TYPE OF TACKLE THE ITEM WILL ACCOMMODATE. SELECT REPLY CODE 10AF37 AMCWJ 04DEPTH,FLAT,FIRST END FIRST END FLAT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMCXJ 04LENGTH,FLAT,FIRST END FIRST END FLAT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FLAT AT THE FIRST END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AMCYJ 04DISTANCE FROM END TO GROOVE,FIRST END FIRST END DISTANCE FROM END TO GROOVE NONE. 2D AND 1B MODE REPLY21AA051AC20 AMCZJ 04WIDTH,KEYWAY,FIRST END FIRST END KEYWAY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE KEYWAY AT THE FIRST END,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AMDAD /D/ 07DEVICE,LOCKING LOCKING DEVICE AN INDICATION OF WHETHER OR NOT A LOCKING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 AMDBD 18TYPE,BECKET BECKET TYPE INDICATES THE TYPE OF BECKET. SELECT REPLY CODE 10AF38 AMDCD /D/ 07DEVICE,ANTITOPPLING ANTITOPPLING DEVICE AN INDICATION OF WHETHER OR NOT AN ANTITOPPLING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 AMDDD 08LOCATION,COUNTERBALANCE COUNTERBALANCE LOCATION INDICATES THE LOCATION OF THE WEIGHT/S/. SELECT REPLY CODE 10AJ91 AMDEJ 04LENGTH,KEYWAY,EXTERNAL,FIRST END FIRST END EXTERNAL KEYWAY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMDFD 19NAME,CUT,PORTION PORTION CUT NAME A DESIGNATION WHICH REPRESENTS THE PORTION CUT. SELECT REPLY CODE 10AJ00 AMDGJ 04DEPTH,KEYWAY,FIRST END FIRST END KEYWAY DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE KEYWAY AT THE FIRST END. 2D AND 1B MODE REPLY21AA051AC20 AMDHJ 04DISTANCE FROM KEYWAY CENTER TO END,FIRST END FIRST END DISTANCE FROM KEYWAY CENTER TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AMDJJ 04THICKNESS,TONGUE,FIRST END FIRST END TONGUE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMDKJ 04WIDTH,TONGUE,FIRST END FIRST END TONGUE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMDLJ 04DIAMETER,END,FIRST FIRST END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FIRST END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMDMJ 04LENGTH,SPLINE,FIRST END FIRST END SPLINE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FIRST END SPLINE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AMDNJ 04DIAMETER,MINOR,FIRST END SPLINE FIRST END SPLINE MINOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST CIRCULAR CROSS SECTION OF THE FIRST END SPLINE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMDPJ 04DIAMETER,MAJOR,FIRST END SPLINE FIRST END SPLINE MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CIRCULAR CROSS SECTION OF THE FIRST END SPLINE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMDQJ /D/ 04WIDTH,SPLINE,FIRST END FIRST END SPLINE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMDRJ 04ANGLE,PRESSURE,FIRST END FIRST END PRESSURE ANGLE NONE. 2D AND 1B MODE REPLY21AF981AC20 AMDSJ 04DIAMETER,PITCH,FIRST END FIRST END PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF THE FIRST END. 2D AND 1B MODE REPLY21AA051AC20 AMDTJ 04DISTANCE ACROSS CORNERS,END,FIRST FIRST END DISTANCE ACROSS CORNERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMDWJ 04DEPTH,SLOT,FIRST END FIRST END SLOT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMDXJ 04DIAMETER,HOLE,FIRST END FIRST END HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE OR BODY OF THE FIRST END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMDYD 04SIZE,CUT CUT SIZE AN INDICATION OF THE SIZE OF CUT. SELECT REPLY CODE 10AJ01 AMDZJ 04DISTANCE FROM HOLE CENTER TO END,END,FIRST FIRST END DISTANCE FROM HOLE CENTER TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AMEAJ 04THREAD LENGTH,EXTERNAL,FIRST END FIRST END EXTERNAL THREAD LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMEBJ 04DEPTH,HOLE,FIRST END FIRST END HOLE DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE HOLE AT THE FIRST END,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AMECJ /D/ 04DEPTH,THRU-HOLE,FIRST END FIRST END THRU-HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMEDD 11METHOD,CUTTING CUTTING METHOD THE MEANS BY WHICH A CUT IS MADE. SELECT REPLY CODE 10AJ02 AMEEJ 04DIAMETER,OUTSIDE,FIRST END GEAR FIRST END GEAR OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FIRST END GEAR,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMEFJ 04WIDTH,FACE,FIRST END GEAR FIRST END GEAR FACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FIRST END GEAR FACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AMEGJ /D/ 04ANGLE,PITCH,FIRST END FIRST END PITCH ANGLE NONE. 2D AND 1B MODE REPLY21AF981AC20 AMEHJ /D/ 04LENGTH,END,FIRST FIRST END LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FIRST END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AMEJJ 04LENGTH,SEAT,FIRST END BEARING FIRST END BEARING SEAT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMEKD 19NAME,CUT,SPECIFIC MEAT SPECIFIC MEAT CUT NAME THE NAME OF A PARTICULAR CUT OF MEAT. SELECT REPLY CODE 10AJ00 AMELJ 04DIAMETER,SEAT,FIRST END BEARING FIRST END BEARING SEAT DIAMETER THE LENGTH OF A STRIAGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FIRST END BEARING SEAT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMEMD 11METHOD,BINDING BINDING METHOD THE MEANS BY WHICH THE ITEM IS BOUND. SELECT REPLY CODE 10AJ03 AMEPJ 04DISTANCE FROM BEARING SEAT TO END,FIRST END FIRST END DISTANCE FROM BEARING SEAT TO END THE MEASURED DISTANCE OF THE FIRST END FROM THE BEARING SEAT TO THE END. 2D AND 1B MODE REPLY21AA051AC20 AMEQD 19CUT,DIVISION DIVISION CUT AN INDICATION OF THE DIVISION CUT. SELECT REPLY CODE 10AJ00 AMERJ 04THREAD LENGTH,INTERNAL,FIRST END FIRST END INTERNAL THREAD LENGTH A MEASUREMENT OF THE EXTENT OF COMPLETE /FULL/ INTERNAL THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS OF THE FIRST END. 2D AND 1B MODE REPLY21AA051AC20 AMESJ 04DISTANCE BETWEEN KEYWAY CENTERS,FIRST END FIRST END DISTANCE BETWEEN KEYWAY CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMETD 19CLASS,MARKET,LIVESTOCK LIVESTOCK MARKET CLASS AN INDICATION OF THE LIVESTOCK MARKET CLASS. SELECT REPLY CODE 10AJ04 AMEWD 18TYPE,CASING,FOOD FOOD CASING TYPE INDICATES THE TYPE OF FOOD CASING PROVIDED. SELECT REPLY CODE 10AE92 AMEXD 11METHOD,CURING CURING METHOD A PROCESS BY WHICH THE ITEM IS PRESERVED. SELECT REPLY CODE 10AJ05 AMEYD 18TYPE,FORMULA FORMULA TYPE INDICATES THE TYPE OF FORMULA PROVIDED. SELECT REPLY CODE 10AJ06 AMEZA 12QUANTITY PER POUND QUANTITY PER POUND THE NUMBER OF ITEMS IN ONE POUND WHEN THE ITEM IS NORMALLY MEASURED IN POUND LOTS. 1A MODE REPLY 0 AMFAJ 10WEIGHT,UNIT,UNPACKAGED UNPACKAGED UNIT WEIGHT THE MEASURED WEIGHT OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING MATERIAL. PLEASE USE MRC CTJS IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY22AB161AC20 AMFBJ 04DISTANCE BETWEEN HOLE CENTERS,FIRST END FIRST END DISTANCE BETWEEN HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMFCJ 04DISTANCE BETWEEN FIRST AND SECOND GROOVE CENTERS,FIRST END FIRST END DISTANCE BETWEEN FIRST AND SECOND GROOVE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMFDJ 04DISTANCE BETWEEN SECOND AND THIRD GROOVE CENTERS,FIRST END FIRST END DISTANCE BETWEEN SECOND AND THIRD GROOVE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMFEJ 04ANGLE BETWEEN KEYWAYS,END,FIRST FIRST END ANGLE BETWEEN KEYWAYS NONE. 2D AND 1B MODE REPLY21AF981AC20 AMFGJ 04LENGTH,FLAT,FIRST END GROOVED FIRST END GROOVED FLAT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMFHJ 04DEPTH,FLAT,FIRST END GROOVED FIRST END GROOVED FLAT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMFJJ 04DISTANCE FROM END TO FLAT,SECOND END SECOND END DISTANCE FROM END TO FLAT NONE. 2D AND 1B MODE REPLY21AA051AC20 AMFKJ 04TAPER,END,SECOND SECOND END TAPER THE AMOUNT OF SECOND END TAPER PER MEASUREMENT SCALE. 3D AND 1B MODE REPLY31AA051AC201AB39 AMFLJ 04DIAMETER,MAJOR,SECOND END TAPER SECOND END TAPER MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CIRCULAR CROSS SECTION OF THE SECOND END TAPERED PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMFMJ 04LENGTH,TAPER,SECOND END SECOND END TAPER LENGTH A MEASUREMENT OF THE LONGEST TAPER DIMENSION AT THE SECOND END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AMFNJ 04DEPTH,FLAT,SECOND END SECOND END FLAT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMFPJ 04LENGTH,FLAT,SECOND END SECOND END FLAT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FLAT AT THE SECOND END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AMFQJ 04DISTANCE FROM END TO GROOVE,SECOND END SECOND END DISTANCE FROM END TO GROOVE NONE. 2D AND 1B MODE REPLY21AA051AC20 AMFRJ 04WIDTH,KEYWAY,SECOND END SECOND END KEYWAY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE KEYWAY AT THE SECOND END,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AMFSJ 04LENGTH,KEYWAY,EXTERNAL,SECOND END SECOND END EXTERNAL KEYWAY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMFTJ 04DEPTH,KEYWAY,SECOND END SECOND END KEYWAY DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE KEYWAY AT THE SECOND END. 2D AND 1B MODE REPLY21AA051AC20 AMFWJ 04DISTANCE FROM KEYWAY CENTER TO END,SECOND END SECOND END DISTANCE FROM KEYWAY CENTER TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AMFXJ 04THICKNESS,TONGUE,SECOND END SECOND END TONGUE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMFYJ 04WIDTH,TONGUE,SECOND END SECOND END TONGUE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMFZJ 04DIAMETER,END,SECOND SECOND END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SECOND END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMGAJ 04LENGTH,SPLINE,SECOND END SECOND END SPLINE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SECOND END SPLINE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AMGBJ 04DIAMETER,MINOR,SECOND END SPLINE SECOND END SPLINE MINOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST CIRCULAR CROSS SECTION OF THE SECOND END SPLINE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMGCJ 04DIAMETER,MAJOR,SECOND END SPLINE SECOND END SPLINE MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CIRCULAR CROSS SECTION OF THE SECOND END SPLINE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMGDJ /D/ 04WIDTH,SPLINE,SECOND END SECOND END SPLINE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMGEJ 04ANGLE,PRESSURE,SECOND END SECOND END PRESSURE ANGLE NONE. 2D AND 1B MODE REPLY21AF981AC20 AMGFJ 04DIAMETER,PITCH,SECOND END SECOND END PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF THE SECOND END. 2D AND 1B MODE REPLY21AA051AC20 AMGGD 18TYPE,CEREAL CEREAL TYPE AN INDICATION OF THE TYPE OF CEREAL PROVIDED. SELECT REPLY CODE 10AE92 AMGHJ 04DISTANCE ACROSS CORNERS,END,SECOND SECOND END DISTANCE ACROSS CORNERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMGJD 19MIXTURE,CEREAL CEREAL MIXTURE AN INDICATION OF THE CEREAL MIXTURE. SELECT REPLY CODE 10AE92 AMGKG 19APPLICATION,PROCESSED,SPECIFIC SPECIFIC PROCESSED APPLICATION AN INDICATION OF THE SPECIFIC APPLICATION OF THE ITEM AFTER PROCESS. FULL TEXT WRITE-IN 0 AMGLD 07PREPARATION,GRAIN GRAIN PREPARATION AN INDICATION OF THE PREPARATION OF THE GRAIN. SELECT REPLY CODE 10AJ08 AMGMD 07QUALITY,NUTRITIVE NUTRITIVE QUALITY AN INDICATION OF WHETHER OR NOT VITAMIN/S/ AND MINERAL/S/ HAVE BEEN ADDED. SELECT REPLY CODE 10AE92 AMGNG 03DESIGNATION,TRADE TRADE DESIGNATION THE DESIGNATION BY WHICH THE ITEM IS IDENTIFIED THROUGHOUT INDUSTRY. FULL TEXT WRITE-IN 0 AMGPD 19LIQUID,PREPARATION PREPARATION LIQUID INDICATES THE LIQUID(S) USED FOR PREPARING THE ITEM. SELECT REPLY CODE 10AE92 AMGQA 12QUANTITY,DOOR,LOADING LOADING DOOR QUANTITY THE NUMBER OF LOADING DOORS PROVIDED. 1A MODE REPLY 0 AMGRJ 04DEPTH,SLOT,SECOND END SECOND END SLOT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMGSJ 04DIAMETER,HOLE,SECOND END SECOND END HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE OR BODY OF THE SECOND END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMGTJ 04DISTANCE FROM HOLE CENTER TO END,END,SECOND SECOND END DISTANCE FROM HOLE CENTER TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AMGWD 18TYPE,ICING,FOOD FOOD ICING TYPE AN INDICATION OF THE TYPE OF FOOD ICING. SELECT REPLY CODE 10AE92 AMGXD 18TYPE,FILLING,FOOD FOOD FILLING TYPE AN INDICATION OF THE TYPE OF FOOD FILLING. SELECT REPLY CODE 10AE92 AMGYD 07TOPPING,FOOD FOOD TOPPING AN INDICATION OF THE FOOD TOPPING PROVIDED. SELECT REPLY CODE 10AE92 AMGZD 18TYPE,COATING,FOOD FOOD COATING TYPE INDICATES THE TYPE OF FOOD COATING. SELECT REPLY CODE 10AE92 AMHAJ 04THREAD LENGTH,EXTERNAL,SECOND END SECOND END EXTERNAL THREAD LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMHBA 12QUANTITY,LAYER LAYER QUANTITY THE NUMBER OF LAYERS PROVIDED. 1A MODE REPLY 0 AMHCA 12QUANTITY,CRUST CRUST QUANTITY THE NUMBER OF CRUSTS PROVIDED. 1A MODE REPLY 0 AMHDJ 04DEPTH,HOLE,SECOND END SECOND END HOLE DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE HOLE AT THE SECOND END,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AMHEJ /D/ 04DEPTH,THRU-HOLE,SECOND END SECOND END THRU-HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMHFJ 04DIAMETER,OUTSIDE,SECOND END GEAR SECOND END GEAR OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SECOND END GEAR,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMHGJ 04WIDTH,FACE,GEAR,SECOND END SECOND END GEAR FACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SECOND END GEAR FACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AMHHJ /D/ 04ANGLE,PITCH,SECOND END SECOND END PITCH ANGLE NONE. 2D AND 1B MODE REPLY21AF981AC20 AMHJJ /D/ 04LENGTH,END,SECOND SECOND END LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SECOND END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AMHKJ 04LENGTH,SEAT,SECOND END BEARING SECOND END BEARING SEAT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMHLJ 04DIAMETER,SEAT,SECOND END BEARING SECOND END BEARING SEAT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SECOND END BEARING SEAT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMHMJ 04DISTANCE FROM BEARING SEAT TO END,SECOND END SECOND END DISTANCE FROM BEARING SEAT TO END THE MEASURED DISTANCE OF THE SECOND END FROM THE BEARING SEAT TO THE END. 2D AND 1B MODE REPLY21AA051AC20 AMHND /D/ 07FEATURE,YEAST YEAST FEATURE AN INDICATION OF WHETHER OR NOT YEAST IS INCLUDED. SELECT REPLY CODE 10AA49 AMHPJ 04THREAD LENGTH,INTERNAL,SECOND END SECOND END INTERNAL THREAD LENGTH A MEASUREMENT OF THE EXTENT OF COMPLETE /FULL/ INTERNAL THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS OF THE SECOND END. 2D AND 1B MODE REPLY21AA051AC20 AMHQJ 04DISTANCE BETWEEN KEYWAY CENTERS,SECOND END SECOND END DISTANCE BETWEEN KEYWAY CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMHRJ 10CAPACITY PER HOUR,HEATING HEATING CAPACITY PER HOUR THE RATED HEATING CAPACITY OF THE ITEM PER HOUR. 1D AND 1B MODE REPLY11AB10 AMHSJ 04DISTANCE BETWEEN HOLE CENTERS,SECOND END SECOND END DISTANCE BETWEEN HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMHTJ 04DISTANCE BETWEEN FIRST AND SECOND GROOVE CENTERS,SECOND END SECOND END DISTANCE BETWEEN FIRST AND SECOND GROOVE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMHWJ 04DISTANCE BETWEEN SECOND AND THIRD GROOVE CENTERS,SECOND END SECOND END DISTANCE BETWEEN SECOND AND THIRD GROOVE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMHXJ 10RISE PER HOUR,TEMP TEMP RISE PER HOUR THE NUMBER OF DEGREES THE TEMPERATURE RISES PER HOUR. 1D AND 1B MODE REPLY11AB36 AMHYJ 04ANGLE BETWEEN KEYWAYS,END,SECOND SECOND END ANGLE BETWEEN KEYWAYS NONE. 2D AND 1B MODE REPLY21AF981AC20 AMHZJ 04ANGLE BETWEEN HOLES,END,SECOND SECOND END ANGLE BETWEEN HOLES NONE. 2D AND 1B MODE REPLY21AF981AC20 AMJAJ 04LENGTH,FLAT,SECOND END GROOVED SECOND END GROOVED FLAT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMJBJ 04DEPTH,FLAT,SECOND END GROOVED SECOND END GROOVED FLAT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMJCD 19SIZE,PRODUCT PRODUCT SIZE AN INDICATION OF THE SIZE OF THE PRODUCT. SELECT REPLY CODE 10AJ10 AMJDJ /D/ 04DIAMETER,BORE,FIRST END FIRST END BORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMJEJ /D/ 04DISTANCE FROM BORE CENTER TO TOP OF KEY,FIRST END FIRST END DISTANCE FROM BORE CENTER TO TOP OF KEY NONE. 2D AND 1B MODE REPLY21AA051AC20 AMJFJ /D/ 04WIDTH,KEY,FIRST END INTERNAL FIRST END INTERNAL KEY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMJGJ /D/ 04WIDTH,KEYWAY,FIRST END INTERNAL FIRST END INTERNAL KEYWAY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMJHJ /D/ 04WIDTH,SPLINE,FIRST END INTERNAL FIRST END INTERNAL SPLINE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMJJJ /D/ 04DIAMETER,MINOR,FIRST END INTERNAL SPLINE FIRST END INTERNAL SPLINE MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMJKJ /D/ 04DIAMETER,MAJOR,FIRST END INTERNAL SPLINE FIRST END INTERNAL SPLINE MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMJLJ /D/ 04DISTANCE FROM BORE CENTER TO BOTTOM OF KEYWAY,FIRST END FIRST END DISTANCE FROM BORE CENTER TO BOTTOM OF KEYWAY NONE. 2D AND 1B MODE REPLY21AA051AC20 AMJMJ /D/ 04DISTANCE ACROSS FLATS,MAJOR,INTERNAL,FIRST END FIRST END INTERNAL MAJOR DISTANCE ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMJNJ /D/ 04DISTANCE ACROSS FLATS,MINOR,INTERNAL,FIRST END FIRST END INTERNAL MINOR DISTANCE ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMJPJ /D/ 04WIDTH ACROSS CORNERS,INTERNAL,FIRST END FIRST END INTERNAL WIDTH ACROSS CORNERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMJQJ /D/ 04DIAMETER,MAJOR,FIRST END TAPERED HOLE FIRST END TAPERED HOLE MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMJRJ /D/ 04DIAMETER,MINOR,FIRST END TAPERED HOLE FIRST END TAPERED HOLE MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMJSJ /D/ 04LENGTH,LEG,FIRST END TRIANGLE FIRST END TRIANGLE LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMJTJ /D/ 04DISTANCE FROM BORE CENTER TO FLAT,FIRST END FIRST END DISTANCE FROM BORE CENTER TO FLAT NONE. 2D AND 1B MODE REPLY21AA051AC20 AMJWA 12QUANTITY OF PERSONS FOR WHICH DESIGNED QUANTITY OF PERSONS FOR WHICH DESIGNED THE SPECIFIC NUMBER OF PERSONS FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 AMJXD /D/ 07SWITCH,THERMOSTATIC THERMOSTATIC SWITCH AN INDICATION OF WHETHER OR NOT A THERMOSTATIC SWITCH IS INCLUDED. SELECT REPLY CODE 10AA49 AMJYA 19NUMBER,MENU MENU NUMBER THE NUMBER ASSIGNED TO A SPECIFIC MENU. 1A MODE REPLY 0 AMJZD 19TITLE,MENU MENU TITLE AN INDICATION OF THE TITLE OF THE MENU. SELECT REPLY CODE 10AE92 AMKAJ /D/ 10CAPACITY,TANK TANK CAPACITY INDICATES THE CAPACITY OF THE TANK. PLEASE USE MRC BSSM IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1B MODE REPLY11AB10 AMKBG /D/ 19INPUT,INFORMATION INFORMATION INPUT THE SPECIFIC INFORMATION FED INTO AN ELECTRONIC DEVICE FOR READY ACCESS. FULL TEXT WRITE-IN 0 AMKCG /D/ 19OUTPUT,INFORMATION INFORMATION OUTPUT THE SPECIFIC INFORMATION OUTPUT TO AN EXTERNAL DEVICE. FULL TEXT WRITE-IN 0 AMKDD 18TYPE,INDICATOR INDICATOR TYPE INDICATES THE TYPE OF DEVICE USED TO REGISTER THE CONDITION(S). SELECT REPLY CODE 10AJ12 AMKEA 12QUANTITY,BAND,TRANSMITTER TRANSMITTER BAND QUANTITY THE NUMBER OF BANDS INCORPORATED IN THE TRANSMITTER. 1A MODE REPLY 0 AMKFJ 10FREQUENCY RATING,SIGNAL,TRANSMITTED TRANSMITTED SIGNAL FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE TRANSMITTED SIGNAL IS RATED. 2D AND 1B MODE REPLY21AC321AC20 AMKGD 18TYPE,UNIT,POWER POWER UNIT TYPE INDICATES THE TYPE OF POWER UNIT INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AJ13 AMKJJ /D/ 10VOLTAGE RATING,UNIT,POWER POWER UNIT VOLTAGE RATING THE VOLTAGE THE POWER UNIT IS DESIGNED TO PRODUCE. 2D AND 1B MODE REPLY21AB631AC20 AMKKJ /D/ 10FREQUENCY RATING,UNIT,POWER POWER UNIT FREQUENCY RATING THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT OF THE POWER UNIT. 2D AND 1B MODE REPLY21AC321AC20 AMKLD 10PHASE,UNIT,POWER POWER UNIT PHASE THE NUMBER OF POWER UNIT ALTERNATING CURRENT PHASES. SELECT REPLY CODE 10AD02 AMKMA 12QUANTITY,CHANNEL,TRANSMITTER TRANSMITTER CHANNEL QUANTITY THE NUMBER OF CHANNELS INCORPORATED IN THE TRANSMITTER. 1A MODE REPLY 0 AMKNJ 10FREQUENCY RATING,SIGNAL,RECEIVED RECEIVED SIGNAL FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE RECEIVED SIGNAL IS RATED. 2D AND 1B MODE REPLY21AC321AC20 AMKPA 12QUANTITY,BAND,RECEIVER RECEIVER BAND QUANTITY THE NUMBER OF BANDS INCORPORATED IN THE RECEIVER. 1A MODE REPLY 0 AMKQA 12QUANTITY,CHANNEL,RECEIVER RECEIVER CHANNEL QUANTITY THE NUMBER OF CHANNELS INCORPORATED IN THE RECEIVER. 1A MODE REPLY 0 AMKRA 12QUANTITY,CHANNEL,CODED CODED CHANNEL QUANTITY THE NUMBER OF CODED CHANNELS INCORPORATED IN THE ITEM. 1A MODE REPLY 0 AMKSD /D/ 18TYPE,INDICATOR INDICATOR TYPE INDICATES THE TYPE OF INDICATOR TO BE USED. SELECT REPLY CODE 10AD51 AMKTJ /D/ 04DIAMETER,BORE,SECOND END SECOND END BORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMKWJ /D/ 04DISTANCE FROM BORE CENTER TO TOP OF KEY,SECOND END SECOND END DISTANCE FROM BORE CENTER TO TOP OF KEY NONE. 2D AND 1B MODE REPLY21AA051AC20 AMKXJ /D/ 04WIDTH,KEY,SECOND END INTERNAL SECOND END INTERNAL KEY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMKYJ /D/ 04WIDTH,KEYWAY,SECOND END INTERNAL SECOND END INTERNAL KEYWAY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMKZJ /D/ 04WIDTH,SPLINE,SECOND END INTERNAL SECOND END INTERNAL SPLINE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMLAJ /D/ 04DIAMETER,MINOR,SECOND END INTERNAL SPLINE SECOND END INTERNAL SPLINE MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMLBJ /D/ 04DIAMETER,MAJOR,SECOND END INTERNAL SPLINE SECOND END INTERNAL SPLINE MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMLCJ /D/ 04DISTANCE FROM BORE CENTER TO BOTTOM OF KEYWAY,SECOND END SECOND END DISTANCE FROM BORE CENTER TO BOTTOM OF KEYWAY NONE. 2D AND 1B MODE REPLY21AA051AC20 AMLDJ /D/ 04DISTANCE ACROSS FLATS,MAJOR,INTERNAL,SECOND END SECOND END INTERNAL MAJOR DISTANCE ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMLEJ /D/ 04DISTANCE ACROSS FLATS,MINOR,INTERNAL,SECOND END SECOND END INTERNAL MINOR DISTANCE ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMLFJ /D/ 04WIDTH ACROSS CORNERS,INTERNAL,SECOND END SECOND END INTERNAL WIDTH ACROSS CORNERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMLGJ /D/ 04DIAMETER,MAJOR,SECOND END TAPERED HOLE SECOND END TAPERED HOLE MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMLHJ /D/ 04DIAMETER,MINOR,SECOND END TAPERED HOLE SECOND END TAPERED HOLE MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMLJJ /D/ 04LENGTH,LEG,SECOND END TRIANGLE SECOND END TRIANGLE LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMLKJ /D/ 04DISTANCE FROM BORE CENTER TO FLAT,SECOND END SECOND END DISTANCE FROM BORE CENTER TO FLAT NONE. 2D AND 1B MODE REPLY21AA051AC20 AMLLJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CONNECTION,WATER INLET WATER INLET CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE WATER INLET CONNECTION. 1D AND 1A MODE REPLY12AH06 AMLMJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CONNECTION,WATER OUTLET WATER OUTLET CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE WATER OUTLET CONNECTION. 1D AND 1A MODE REPLY12AH06 AMLND 19CORRELATION,INDICATOR INDICATOR CORRELATION THE TERMINOLOGY USED TO DESIGNATE A PARTICULAR RELATIONSHIP OF THE INDICATOR TO THE ITEM. SELECT REPLY CODE 10AH00 AMLPD /D/ 18TYPE,DECODE,SIGNAL SIGNAL DECODE TYPE INDICATES THE TYPE OF SIGNAL TO BE DECODED. SELECT REPLY CODE 10AJ14 AMLQA 12QUANTITY,CONNECTION,WATER INLET WATER INLET CONNECTION QUANTITY THE NUMBER OF WATER INLET CONNECTIONS. 1A MODE REPLY 0 AMLRA 12QUANTITY,CONNECTION,WATER OUTLET WATER OUTLET CONNECTION QUANTITY THE NUMBER OF WATER OUTLET CONNECTIONS. 1A MODE REPLY 0 AMLSJ /D/ 04DIAMETER,HOLE,FIRST END YOKE BEARING FIRST END YOKE BEARING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMLTJ /D/ 04HEIGHT,FORK,FIRST END YOKE FIRST END YOKE FORK HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AMLWJ /D/ 10SPAN,FORK,FIRST END YOKE FIRST END YOKE FORK SPAN NONE. 2D AND 1B MODE REPLY21AA051AC20 AMLXJ /D/ 04DEPTH,FORK,FIRST END YOKE FIRST END YOKE FORK DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMLYJ /D/ 04DEPTH,RECESS,FIRST END YOKE BEARING FIRST END YOKE BEARING RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMLZJ /D/ 04DISTANCE FROM FLANGE TO YOKE,FIRST END FIRST END DISTANCE FROM FLANGE TO YOKE NONE. 2D AND 1B MODE REPLY21AA051AC20 AMMAJ /D/ 04DIAMETER,HOLE,BOLT,FIRST END YOKE FIRST END YOKE BOLT HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMMBJ /D/ 04DISTANCE BETWEEN YOKE BOLT HOLES,CENTER TO CENTER,FIRST END FIRST END CENTER TO CENTER DISTANCE BETWEEN YOKE BOLT HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AMMCJ /D/ 04DEPTH,KEYWAY,FIRST END YOKE BEARING FIRST END YOKE BEARING KEYWAY DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMMDA 12QUANTITY,SIGNAL,INPUT INPUT SIGNAL QUANTITY THE NUMBER OF SIGNALS WHICH THE ITEM IS CAPABLE OF RECEIVING. 1A MODE REPLY 0 AMMEG /D/ 19OUTPUT,SIGNAL SIGNAL OUTPUT THE SIGNAL THAT IS OUTPUT BY THE ITEM. FULL TEXT WRITE-IN 0 AMMFD /D/ 07MODULATOR,INTEGRAL INTEGRAL MODULATOR AN INDICATION OF WHETHER OR NOT AN INTEGRAL MODULATOR IS INCLUDED. SELECT REPLY CODE 10AA49 AMMGJ /D/ 04DIAMETER,HOLE,SECOND END YOKE BEARING SECOND END YOKE BEARING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMMHJ /D/ 04HEIGHT,FORK,SECOND END YOKE SECOND END YOKE FORK HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AMMJJ /D/ 10SPAN,FORK,SECOND END YOKE SECOND END YOKE FORK SPAN NONE. 2D AND 1B MODE REPLY21AA051AC20 AMMKJ /D/ 04DEPTH,FORK,SECOND END YOKE SECOND END YOKE FORK DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMMLJ /D/ 04DEPTH,RECESS,SECOND END YOKE BEARING SECOND END YOKE BEARING RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMMMJ /D/ 04DISTANCE FROM FLANGE TO YOKE,SECOND END SECOND END DISTANCE FROM FLANGE TO YOKE NONE. 2D AND 1B MODE REPLY21AA051AC20 AMMNJ /D/ 04DIAMETER,HOLE,BOLT,SECOND END YOKE SECOND END YOKE BOLT HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMMPJ /D/ 04DISTANCE BETWEEN YOKE BOLT HOLES,CENTER TO CENTER,SECOND END SECOND END CENTER TO CENTER DISTANCE BETWEEN YOKE BOLT HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AMMQJ /D/ 04DEPTH,KEYWAY,SECOND END YOKE BEARING SECOND END YOKE BEARING KEYWAY DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMMRJ 10DURATION,PULSE PULSE DURATION THE TIME REQUIRED FOR ONE COMPLETE PULSE. 1D AND 1B MODE REPLY12AB49 AMMSJ 10OUTPUT,POWER POWER OUTPUT THE AMOUNT OF ELECTRICAL POWER WHICH THE ITEM IS CAPABLE OF PRODUCING. 2D AND 1B MODE REPLY21AC331AC20 AMMTJ /D/ 04HEIGHT,OVERALL,YOKE MOUNTING FLANGE,FIRST END FIRST END YOKE MOUNTING FLANGE OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AMMWJ /D/ 04WIDTH,FLANGE,FIRST END YOKE MOUNTING FIRST END YOKE MOUNTING FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMMXJ /D/ 04DISTANCE BETWEEN VERTICAL HOLE CENTERS ON YOKE MOUNTING FLANGE,FIRST END FIRST END DISTANCE BETWEEN VERTICAL HOLE CENTERS ON YOKE MOUNTING FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 AMMYJ /D/ 04DISTANCE BETWEEN HORIZONTAL HOLE CENTERS ON YOKE MOUNTING FLANGE,FIRST END FIRST END DISTANCE BETWEEN HORIZONTAL HOLE CENTERS ON YOKE MOUNTING FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 AMMZJ /D/ 04DIAMETER,CIRCLE,BOLT,FIRST END YOKE MOUNTING FLANGE FIRST END YOKE MOUNTING FLANGE BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMNAJ /D/ 04DIAMETER,HOLE,YOKE MOUNTING FLANGE,FIRST END FIRST END YOKE MOUNTING FLANGE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMNBJ /D/ 04DIAMETER,HOLE,FIRST END PILOT FIRST END PILOT HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMNCJ /D/ 04DIAMETER,OVERALL,YOKE MOUNTING FLANGE,FIRST END FIRST END YOKE MOUNTING FLANGE OVERALL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMNDJ 10IMPEDANCE RATING,INPUT INPUT IMPEDANCE RATING THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) PRESENTED BY THE ITEM TO AN ALTERNATING CURRENT SOURCE. 2D AND 1B MODE REPLY22AE751AC20 AMNEJ 10IMPEDANCE RATING,OUTPUT OUTPUT IMPEDANCE RATING THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) PRESENTED BY THE ITEM TO AN ALTERNATING CURRENT LOAD. 2D AND 1B MODE REPLY22AE751AC20 AMNFB /D/ 04ANGLE IN DEG,CHAMFER,ALL CORNERS ALL CORNERS CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AMNGJ /D/ 04LENGTH,CHAMFER,ALL CORNERS ALL CORNERS CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 AMNHJ /D/ 04RADIUS,CHAMFER,ALL CORNERS ALL CORNERS CHAMFER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMNJG /D/ 03DESIGNATOR,TUBE,RAY,CATHODE CATHODE RAY TUBE DESIGNATOR THE ALPHA AND/OR NUMERIC DESIGNATOR BY WHICH THE CATHODE RAY TUBE IS IDENTIFIED. FULL TEXT WRITE-IN 0 AMNKG 19CALIBRATION,SCALE SCALE CALIBRATION AN INDICATION OF THE MANNER IN WHICH THE SCALE IS CALIBRATED. FULL TEXT WRITE-IN 0 AMNLD 18TYPE,PRESENTATION PRESENTATION TYPE INDICATES THE TYPE OF PRESENTATION. SELECT REPLY CODE 10AJ15 AMNMJ /D/ 04HEIGHT,OVERALL,YOKE MOUNTING FLANGE,SECOND END SECOND END YOKE MOUNTING FLANGE OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AMNNJ /D/ 04WIDTH,FLANGE,SECOND END YOKE MOUNTING SECOND END YOKE MOUNTING FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMNPJ /D/ 04DISTANCE BETWEEN HORIZONTAL HOLE CENTERS ON YOKE MOUNTING FLANGE,SECOND END SECOND END DISTANCE BETWEEN HORIZONTAL HOLE CENTERS ON YOKE MOUNTING FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 AMNQJ /D/ 04DIAMETER,CIRCLE,BOLT,SECOND END YOKE MOUNTING FLANGE SECOND END YOKE MOUNTING FLANGE BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMNRJ /D/ 04DIAMETER,HOLE,YOKE MOUNTING FLANGE,SECOND END SECOND END YOKE MOUNTING FLANGE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMNSJ /D/ 04DIAMETER,HOLE,SECOND END PILOT SECOND END PILOT HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMNTJ /D/ 04DIAMETER,OVERALL,YOKE MOUNTING FLANGE,SECOND END SECOND END YOKE MOUNTING FLANGE OVERALL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMNWJ /D/ 04DISTANCE BETWEEN VERTICAL HOLE CENTERS ON YOKE MOUNTING FLANGE,SECOND END SECOND END DISTANCE BETWEEN VERTICAL HOLE CENTERS ON YOKE MOUNTING FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 AMNXA 12QUANTITY,CONNECTION,GAS GAS CONNECTION QUANTITY THE NUMBER OF GAS CONNECTIONS. 1A MODE REPLY 0 AMNZJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CONNECTION,GAS GAS CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE GAS CONNECTION. 1D AND 1A MODE REPLY12AH06 AMPAJ 10SIZE,PIPE,FLUE FLUE PIPE SIZE THE NUMERIC SIZE DESIGNATION OF THE FLUE PIPE. 2D AND 1B MODE REPLY21AA051AC20 AMPBJ /D/ 04THICKNESS,OVERALL,FIRST END FIRST END OVERALL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AMPCJ 04THICKNESS AT MOUNTING HOLES,END,FIRST FIRST END THICKNESS AT MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AMPDJ /D/ 04DIAMETER,HOLE,FIRST END PLAIN FIRST END PLAIN HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMPEJ /D/ 04DIAMETER,MAJOR,FLANGE TAPERED HOLE,FIRST END FIRST END FLANGE TAPERED HOLE MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMPFJ /D/ 04TAPER,HOLE,FIRST END FLANGE FIRST END FLANGE HOLE TAPER NONE. 3D AND 1B MODE REPLY31AA051AC201AB39 AMPGJ 04LENGTH FROM STUD END TO FLANGE FACE,FIRST END FIRST END LENGTH FROM STUD END TO FLANGE FACE A MEASUREMENT OF THE LONGEST DIMENSION OF THE FIRST END FROM THE STUD END TO THE FLANGE FACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AMPHD 18TYPE,GAP GAP TYPE AN INDICATION OF THE TYPE OF GAP. SELECT REPLY CODE 10AJ16 AMPJD /D/ 07MOTOR MOTOR AN INDICATION OF WHETHER OR NOT A MOTOR IS INCLUDED. SELECT REPLY CODE 10AA49 AMPKD /D/ 09MATERIAL,ELECTRODE ELECTRODE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH AN ELECTRODE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AMPLJ /D/ 04THICKNESS,OVERALL,SECOND END SECOND END OVERALL THICKNESS NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 AMPMJ 04THICKNESS AT MOUNTING HOLES,END,SECOND SECOND END THICKNESS AT MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AMPNJ /D/ 04DIAMETER,HOLE,SECOND END PLAIN SECOND END PLAIN HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMPPJ /D/ 04DIAMETER,MAJOR,FLANGE TAPERED HOLE,SECOND END SECOND END FLANGE TAPERED HOLE MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMPQJ /D/ 04TAPER,HOLE,SECOND END FLANGE SECOND END FLANGE HOLE TAPER NONE. 3D AND 1B MODE REPLY31AA051AC201AB39 AMPRJ /D/ 04LENGTH FROM STUD END TO FLANGE FACE,SECOND END SECOND END LENGTH FROM STUD END TO FLANGE FACE NONE. 2D AND 1B MODE REPLY21AA051AC20 AMPSB 10CURRENT RATING IN AMPS CURRENT RATING IN AMPS THE ELECTRICAL CURRENT RATING,EXPRESSED IN AMPERES. 1B MODE REPLY 0 AMPTL /D/ 16STYLE,HOSE HOSE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HOSE. 1L MODE REPLY 0 AMPWD /D/ 07STRIP,SCUFF SCUFF STRIP AN INDICATION OF WHETHER OR NOT A SCUFF STRIP FOR PROTECTING THE ITEM IS INCLUDED. SELECT REPLY CODE 10AA49 AMPXD /D/ 09MATERIAL,HOSE HOSE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HOSE IS FABRICATED,EXCLUDING ANY END FITTINGS. SELECT REPLY CODE 10AD09 AMPYJ 10WEIGHT,HOSE HOSE WEIGHT THE WEIGHT PER SPECIFIC LENGTH OF HOSE. 1D AND 1B MODE REPLY12AG67 AMPZJ T10RANGE,TEMP TEMP RANGE THE MINIMUM AND MAXIMUM DEGREES OF TEMPERATURE AN ITEM CAN WITHSTAND WITHOUT DETRIMENTAL EFFECT. 1D AND 1F MODE REPLY11AB39 AMQAD 18TYPE,END,FIRST FIRST END TYPE A NARRATIVE DESCRIPTION OF THE FIRST END. SELECT REPLY CODE 10AC41 AMQBD /D/ 09MATERIAL,COUPLING,FIRST END FIRST END COUPLING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FIRST END COUPLING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AMQCD /D/ 17SURFACE TREATMENT,COUPLING,FIRST END FIRST END COUPLING SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A SURFACE OF THE FIRST END COUPLING. SELECT REPLY CODE 10AD09 AMQDL /D/ 16STYLE,COUPLING,FIRST END FIRST END COUPLING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FIRST END COUPLING. 1L MODE REPLY 0 AMQEJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,COUPLING,END,FIRST FIRST END COUPLING THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE FIRST END COUPLING. 1D AND 1A MODE REPLY12AH06 AMQFD 18TYPE,END,SECOND SECOND END TYPE A NARRATIVE DESCRIPTION OF THE SECOND END. SELECT REPLY CODE 10AC41 AMQGD /D/ 09MATERIAL,COUPLING,SECOND END SECOND END COUPLING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SECOND END COUPLING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AMQHD /D/ 17SURFACE TREATMENT,COUPLING,SECOND END SECOND END COUPLING SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A SURFACE OF THE SECOND END COUPLING. SELECT REPLY CODE 10AD09 AMQJL /D/ 16STYLE,COUPLING,SECOND END SECOND END COUPLING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SECOND END COUPLING. 1L MODE REPLY 0 AMQKA /D/ 12QUANTITY,DEVICE,LOCKING,SECOND END COUPLING SECOND END COUPLING LOCKING DEVICE QUANTITY THE NUMBER OF LOCKING DEVICES INCLUDED ON THE SECOND END COUPLING. 1A MODE REPLY 0 AMQLJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,COUPLING,END,SECOND SECOND END COUPLING THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE SECOND END COUPLING. 1D AND 1A MODE REPLY12AH06 AMQMD /D/ 07CABLE,COMMUNICATION COMMUNICATION CABLE AN INDICATION OF WHETHER OR NOT A COMMUNICATION CABLE IS INCLUDED. SELECT REPLY CODE 10AA49 AMQNA 12QUANTITY,CONDUCTOR CONDUCTOR QUANTITY THE NUMBER OF ELECTRICAL CONDUCTORS INCLUDED ON THE ITEM. 1A MODE REPLY 0 AMQPD /D/ 18TYPE,TERMINAL,FIRST END FIRST END TERMINAL TYPE INDICATES THE TYPE OF TERMINAL(S) FURNISHED ON THE FIRST END. SELECT REPLY CODE 10AA58 AMQQA /D/ 12QUANTITY,TERMINAL,FIRST END FIRST END TERMINAL QUANTITY THE NUMBER OF TERMINALS FURNISHED ON THE FIRST END. 1A MODE REPLY 0 AMQRD /D/ 18TYPE,TERMINAL,SECOND END SECOND END TERMINAL TYPE INDICATES THE TYPE OF TERMINAL(S) FURNISHED ON THE SECOND END. SELECT REPLY CODE 10AA58 AMQSA /D/ 12QUANTITY,TERMINAL,SECOND END SECOND END TERMINAL QUANTITY THE NUMBER OF TERMINALS FURNISHED ON THE SECOND END. 1A MODE REPLY 0 AMQTD /D/ 07FEATURE,ADJUSTABILITY ADJUSTABILITY FEATURE AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AMQWD /D/ 07CORD,RESTRAINT RESTRAINT CORD AN INDICATION OF WHETHER OR NOT A RESTRAINT CORD IS INCLUDED. SELECT REPLY CODE 10AA49 AMQXD /D/ 07DEVICE,STOWAGE STOWAGE DEVICE AN INDICATION OF WHETHER OR NOT A STOWAGE DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 AMQYD 02DESIGN,INSTALLATION INSTALLATION DESIGN THE INSTALLATION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AJ17 AMQZJ 04LENGTH,COMPRESSED COMPRESSED LENGTH A MEASUREMENT OF THE SMALLEST LENGTH TO WHICH THE ITEM MAY BE COMPRESSED,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AMRAJ /D/ 04WIDTH,INSIDE,FIRST END FIRST END INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMRBJ /D/ 04LENGTH,INSIDE,FIRST END FIRST END INSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMRCJ /D/ 04WIDTH,INSIDE,SECOND END SECOND END INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMRDJ /D/ 04LENGTH,INSIDE,SECOND END SECOND END INSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AMREJ 10PRESSURE,OPERATING,MAXIMUM,HEATING COIL HEATING COIL MAXIMUM OPERATING PRESSURE THE MAXIMUM PRESSURE AT WHICH THE HEATING COIL IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY11AB18 AMRFJ 10AREA,SURFACE,HEATING COIL HEATING COIL SURFACE AREA AN INDICATION OF THE SURFACE AREA OF A HEATING COIL. 1D AND 1B MODE REPLY11AC51 AMRGJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CONNECTION,HEATING COIL INLET HEATING COIL INLET CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE HEATING COIL INLET CONNECTION. 1D AND 1A MODE REPLY12AH06 AMRHJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CONNECTION,HEATING COIL OUTLET HEATING COIL OUTLET CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE HEATING COIL OUTLET CONNECTION. 1D AND 1A MODE REPLY12AH06 AMRJD /D/ 08LOCATION,COVERING COVERING LOCATION INDICATES THE LOCATION OF AN ITEM TO WHICH COVERING HAS BEEN APPLIED. SELECT REPLY CODE 10AE46 AMRKJ 10WATTAGE RATING,ELEMENT,HEATING HEATING ELEMENT WATTAGE RATING THE RATED POWER WHICH A HEATING ELEMENT CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS. 1D AND 1B MODE REPLY12AJ11 AMRLJ 04LENGTH,NOMINAL,TACKLE TACKLE NOMINAL LENGTH A MEASUREMENT OF THE LONGEST NOMINAL DIMENSION OF THE TACKLE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AMRMH 18TYPE AND FUNCTION,RADIATION RADIATION TYPE AND FUNCTION INDICATES THE RADIATION TYPE AND FUNCTION. 2D MODE REPLY 22AJ182AJ19 AMRNJ 03DESIGNATOR,SIZE SIZE DESIGNATOR A DESIGNATION INDICATING THE SIZE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 2D AND 1B MODE REPLY21AA051AC20 AMRPJ 10ENERGY RATING,RADIATION RADIATION ENERGY RATING AN INDICATION OF THE RADIATION ENERGY THE ITEM IS CAPABLE OF HANDLING WITHIN A SPECIFIED PERIOD OF TIME. 3D AND 1B MODE REPLY32AJ201AC111AC20 AMRQJ 04LENGTH,SHELL SHELL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SHELL,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AMRRJ 04DIAMETER,OUTSIDE,SHEAVE SHEAVE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SHEAVE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMRSJ 04DIAMETER,OUTSIDE,SECOND SHEAVE SECOND SHEAVE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMRTJ 04DIAMETER,PIN,CENTER CENTER PIN DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMRWJ 04DIAMETER,PIN,CENTER,SECOND SECOND CENTER PIN DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AMRXD 18TYPE,ELEMENT,DETECTING DETECTING ELEMENT TYPE INDICATES THE TYPE OF DETECTING ELEMENT INCLUDED. SELECT REPLY CODE 10AJ21 AMRYA 12QUANTITY,BECKET BECKET QUANTITY THE NUMBER OF BECKETS PROVIDED. 1A MODE REPLY 0 AMRZD 07DETACHABILITY,ELEMENT,DETECTING DETECTING ELEMENT DETACHABILITY AN INDICATION OF WHETHER OR NOT THE DETECTING ELEMENT CAN BE DETACHED FROM THE ITEM. SELECT REPLY CODE 10AH97 AMSAG 19AGENCY,CONTROLLING CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE ITEM. FULL TEXT WRITE-IN 0 AMSBJ A19NUMBER,IDENTIFYING IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE ITEM. 1D AND 1A MODE REPLY12AG99 AMSCJ 04DIAMETER,INSIDE,ENVELOPE ENVELOPE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO INSIDE SURFACES OF THE ENVELOPE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMSDJ 04DISTANCE,TRAVEL,VALVE VALVE TRAVEL DISTANCE THE MEASURED DISTANCE THE VALVE TRAVELS. 2D AND 1B MODE REPLY21AA051AC20 AMSEJ 10VOLTAGE RATING VOLTAGE RATING THE VALUE(S) OF POTENTIAL FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY21AB631AC20 AMSFJ 04DIAMETER,ORIFICE ORIFICE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ORIFICE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMSGJ 04DIAMETER,FACE,VALVE VALVE FACE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE VALVE FACE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMSHB 10VOLTAGE IN VOLTS,LENGTH,PLATEAU PLATEAU LENGTH VOLTAGE IN VOLTS THE RANGE OF APPLIED VOLTAGE OVER WHICH THE PLATEAU OF A RADIATION COUNTER TUBE EXTENDS,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AMSJB 10VOLTAGE IN VOLTS,THRESHOLD THRESHOLD VOLTAGE IN VOLTS THE LEAST VALUE OF ELECTRICAL POTENTIAL THAT PRODUCES A MINIMUM DETECTABLE RESPONSE,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AMSKA 12QUANTITY,RIB,SUPPORTING SUPPORTING RIB QUANTITY THE NUMBER OF SUPPORTING RIBS PROVIDED. 1A MODE REPLY 0 AMSLD /D/ 07PREAMPLIFIER PREAMPLIFIER AN INDICATION OF WHETHER OR NOT A PREAMPLIFIER IS INCLUDED. SELECT REPLY CODE 10AA49 AMSMD /D/ 07PHOTOMULTIPLIER PHOTOMULTIPLIER AN INDICATION OF WHETHER OR NOT A PHOTOMULTIPLIER IS INCLUDED. SELECT REPLY CODE 10AA49 AMSND /D/ 07CONNECTOR CONNECTOR AN INDICATION OF WHETHER OR NOT A CONNECTOR IS INCLUDED. SELECT REPLY CODE 10AA49 AMSPD /D/ 09MATERIAL,BASIC BASIC MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BASIC MATERIAL IS FABRICATED. PLEASE USE MRC CYEN IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AMSQA 12QUANTITY,ELEMENT,DETECTING DETECTING ELEMENT QUANTITY THE NUMBER OF DETECTING ELEMENTS. 1A MODE REPLY 0 AMSRA /D/ 16STYLE,EDGE,ATTACHING ATTACHING EDGE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ATTACHING EDGE. 1A MODE REPLY 0 AMSTD 02DESIGN,ACTIVE FACE ACTIVE FACE DESIGN THE DESIGN OF THE ACTIVE FACE. SELECT REPLY CODE 10AB80 AMSWL 16STYLE,STUD,SEAT SEAT STUD STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SEAT STUD. 1L MODE REPLY 0 AMSXD 18TYPE,DESIGN,PROJECTILE PROJECTILE DESIGN TYPE INDICATES THE DESIGN TYPE CHARACTERISTIC OF THE PROJECTILE. SELECT REPLY CODE 10AJ22 AMSYJ 10VELOCITY,MUZZLE MUZZLE VELOCITY THE VELOCITY OF AN ITEM AT THE MOMENT OF LEAVING THE MUZZLE. 2D AND 1B MODE REPLY22AG201AC20 AMSZD /D/ 07STREAMER,WARNING WARNING STREAMER AN INDICATION OF WHETHER OR NOT A WARNING STREAMER IS INCLUDED. PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AMTAD 05DIRECTION,FEED,LINK LINK FEED DIRECTION THE DIRECTION THE LINK FEED IS DESIGNED TO CONVEY THE ITEM. SELECT REPLY CODE 10AA38 AMTBD /D/ 07LINK,END END LINK AN INDICATION OF WHETHER OR NOT AN END LINK IS INCLUDED. SELECT REPLY CODE 10AA49 AMTCJ 10VOLUME,FLUID,MAXIMUM MAXIMUM FLUID VOLUME THE MAXIMUM AMOUNT OF FLUID FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AD42 AMTDD 18TYPE,SEPARATOR SEPARATOR TYPE INDICATES THE TYPE OF SEPARATOR FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AC58 AMTED /D/ 07OPENING,BLEEDER BLEEDER OPENING AN INDICATION OF WHETHER OR NOT A BLEEDER OPENING IS INCLUDED. SELECT REPLY CODE 10AA49 AMTFJ 13SCREW THREAD DIAMETER,PORT PORT SCREW THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COAXIAL CYLINDER,WHICH WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD OF A PORT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMTGD 07MARKINGS,CHARACTERISTIC,PROPELLANT PROPELLANT CHARACTERISTIC MARKINGS AN INDICATION OF WHETHER OR NOT PROPELLANT CHARACTERISTIC MARKINGS ARE REQUIRED. SELECT REPLY CODE 10AE40 AMTHD /D/ 07BUTTON,RESET RESET BUTTON AN INDICATION OF WHETHER OR NOT A RESET BUTTON IS INCLUDED. SELECT REPLY CODE 10AA49 AMTJD 18TYPE,GRANULATION,PROPELLANT PROPELLANT GRANULATION TYPE INDICATES THE TYPE OF PROPELLANT GRANULATION USED WITH THE ITEM. SELECT REPLY CODE 10AN45 AMTKD /D/ 07LEVER,SETTING SETTING LEVER AN INDICATION OF WHETHER OR NOT A SETTING LEVER IS INCLUDED. SELECT REPLY CODE 10AA49 AMTLD 18TYPE,CONNECTION,AIR PRESSURE INLET PORT AIR PRESSURE INLET PORT CONNECTION TYPE INDICATES THE TYPE OF CONNECTION PROVIDED FOR THE AIR PRESSURE TO THE INLET PORT. SELECT REPLY CODE 10AJ68 AMTMD 07ADAPTABILITY,FUZE,PROXIMITY PROXIMITY FUZE ADAPTABILITY AN INDICATION OF WHETHER OR NOT THE ITEM IS ADAPTABLE FOR PROXIMITY FUZE. SELECT REPLY CODE 10AJ23 AMTNJ 04DIAMETER,PORT,INLET INLET PORT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INLET PORT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMTPD 18TYPE,CONNECTION,PORT,OUTLET,PRESSURE,AIR AIR PRESSURE OUTLET PORT CONNECTION TYPE INDICATES THE TYPE OF CONNECTION PROVIDED FOR THE AIR PRESSURE TO THE OUTLET PORT. SELECT REPLY CODE 10AJ68 AMTQJ 04DIAMETER,PORT,OUTLET OUTLET PORT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTLET PORT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMTRA 19NUMBER,MODEL,NOSE FUZE NOSE FUZE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE NOSE FUZE. 1A MODE REPLY 0 AMTSA 19NUMBER,MODEL,BASE FUZE BASE FUZE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE BASE FUZE. 1A MODE REPLY 0 AMTTD 18TYPE,CONNECTION,AIR PRESSURE EXHAUST PORT AIR PRESSURE EXHAUST PORT CONNECTION TYPE INDICATES THE TYPE OF CONNECTION PROVIDED FOR THE AIR PRESSURE TO THE EXHAUST PORT. SELECT REPLY CODE 10AJ68 AMTWJ 04DIAMETER,PORT,EXHAUST EXHAUST PORT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE EXHAUST PORT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMTXA 19NUMBER,MODEL,PERCUSSION PRIMER PERCUSSION PRIMER MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE PERCUSSION PRIMER. 1A MODE REPLY 0 AMTYD 18TYPE,CONNECTION,OIL OUTLET PORT OIL OUTLET PORT CONNECTION TYPE INDICATES THE TYPE OF CONNECTION PROVIDED FOR THE OIL TO THE OUTLET PORT. SELECT REPLY CODE 10AJ68 AMTZJ 04DIAMETER,PORT,OUTLET,OIL OIL OUTLET PORT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OIL OUTLET PORT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMWAD /D/ 09MATERIAL,CHARGE,PROPELLING PROPELLING CHARGE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PROPELLING CHARGE IS COMPOSED. SELECT REPLY CODE 10AD09 AMWBJ 04DIAMETER,HOLE,DRAIN DRAIN HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DRAIN HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMWCD 07PROVISION,THREAD,PRESSURE VENT PRESSURE VENT THREAD PROVISION AN INDICATION OF THE PRESSURE VENT THREAD PROVISION ON THE ITEM. SELECT REPLY CODE 10AE00 AMWDD 18TYPE,PROPELLER PROPELLER TYPE AN INDICATION OF THE TYPE OF PROPELLER. SELECT REPLY CODE 10AJ25 AMWED /D/ 18TYPE,ADJUSTMENT ADJUSTMENT TYPE INDICATES THE TYPE OF ADJUSTMENT INCLUDED IN THE ITEM. SELECT REPLY CODE 10AD63 AMWFD 18TYPE,CONTROL,PITCH PITCH CONTROL TYPE THE MEANS BY WHICH CHANGES OF BLADE PITCH ARE EFFECTED. SELECT REPLY CODE 10AC58 AMWGD 07SYSTEM,POWER,PITCH CONTROL PITCH CONTROL POWER SYSTEM INDICATES WHETHER OR NOT THE PITCH CONTROL POWER SYSTEM IS SELF-CONTAINED. SELECT REPLY CODE 10AJ26 AMWHD /D/ 11METHOD,CONTROL CONTROL METHOD THE MEANS BY WHICH THE ITEM IS CONTROLLED. SELECT REPLY CODE 10AA77 AMWJD /D/ 07FEATURE,WINTERIZATION WINTERIZATION FEATURE AN INDICATION OF WHETHER OR NOT WINTERIZATION IS INCLUDED. SELECT REPLY CODE 10AA49 AMWKD 11METHOD,OPERATION,BYPASS VALVE BYPASS VALVE OPERATION METHOD THE MEANS USED TO OPERATE THE BYPASS VALVE. SELECT REPLY CODE 10AA77 AMWLJ 04LENGTH,STROKE STROKE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE STROKE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AMWMD 18TYPE,ACTION ACTION TYPE INDICATES THE TYPE OF ACTION PROVIDED. SELECT REPLY CODE 10AJ27 AMWNA 19NUMBER,MODEL MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE ITEM. 1A MODE REPLY 0 AMWPD /D/ 07GAGE,PRESSURE PRESSURE GAGE AN INDICATION OF WHETHER OR NOT A PRESSURE GAGE IS INCLUDED. SELECT REPLY CODE 10AA49 AMWQD /D/ 07INDICATOR,FLOW FLOW INDICATOR AN INDICATION OF WHETHER OR NOT A FLOW INDICATOR IS INCLUDED. SELECT REPLY CODE 10AA49 AMWRA 12QUANTITY,CHAMBER CHAMBER QUANTITY THE NUMBER OF CHAMBERS PROVIDED. 1A MODE REPLY 0 AMWSD /D/ 07FEATURE,FEATHERING FEATHERING FEATURE AN INDICATION OF WHETHER OR NOT A FEATHERING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AMWTD 07REVERSIBILITY REVERSIBILITY AN INDICATION OF WHETHER OR NOT AN ITEM IS REVERSIBLE. SELECT REPLY CODE 10AF62 AMWWD 05DIRECTION,ROTATION ROTATION DIRECTION THE DIRECTION IN WHICH AN ITEM IS DESIGNED TO ROTATE,WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AA38 AMWXD 11METHOD,FEED FEED METHOD THE MEANS BY WHICH THE ITEM IS FED. SELECT REPLY CODE 10AJ28 AMWYJ 04DIAMETER,MAXIMUM,SPAN SPAN MAXIMUM DIAMETER THE MAXIMUM ALLOWABLE DIAMETER OF THE CIRCLE PRODUCED BY THE EXTREME TIP OF THE ITEM. 1D AND 1B MODE REPLY11AA05 AMWZD 11METHOD,LUBRICATION,SHEAVE BEARING SHEAVE BEARING LUBRICATION METHOD THE MEANS BY WHICH THE SHEAVE BEARING IS LUBRICATED. SELECT REPLY CODE 10AC75 AMXAD 07REMOVABILITY,FAIRING,BLADE BLADE FAIRING REMOVABILITY AN INDICATION OF THE REMOVABILITY OF THE BLADE FAIRING. SELECT REPLY CODE 10AC29 AMXBJ 10PITCH,DESIGN DESIGN PITCH THE MEAN DISTANCE OF FORWARD MOVEMENT FOR EACH REVOLUTION OF THE ITEM. 1D AND 1B MODE REPLY11AA05 AMXCJ 04DIAMETER ACCOMMODATED,TACKLE,MAXIMUM MAXIMUM TACKLE DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR A TACKLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AMXDD /D/ 07DEVICE,LOCKING,TACKLE TACKLE LOCKING DEVICE AN INDICATION OF WHETHER OR NOT A TACKLE LOCKING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 AMXEA 10CAPACITY,DEVICE,FEEDING FEEDING DEVICE CAPACITY AN INDICATION OF THE CAPACITY OF THE FEEDING DEVICE. 1A MODE REPLY 0 AMXFL 16STYLE,ATTACHMENT ATTACHMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ATTACHMENT. 1L MODE REPLY 0 AMXGD 18TYPE,PITCH,BLADE BLADE PITCH TYPE AN INDICATION OF THE TYPE OF BLADE PITCH. SELECT REPLY CODE 10AL77 AMXHD 18TYPE,BREECHBLOCK BREECHBLOCK TYPE INDICATES THE TYPE OF BREECHBLOCK PROVIDED. SELECT REPLY CODE 10AJ29 AMXJD /D/ 07SWITCH,ON-OFF ON-OFF SWITCH AN INDICATION OF WHETHER OR NOT AN ON-OFF SWITCH IS INCLUDED. SELECT REPLY CODE 10AA49 AMXKD /D/ 07PANEL,LIGHTED LIGHTED PANEL AN INDICATION OF WHETHER OR NOT A LIGHTED PANEL IS INCLUDED. SELECT REPLY CODE 10AA49 AMXLD 18TYPE,CONTROL,EMERGENCY OXYGEN EMERGENCY OXYGEN CONTROL TYPE INDICATES THE TYPE OF CONTROL FOR THE EMERGENCY OXYGEN. SELECT REPLY CODE 10AE34 AMXMB 19STATION,RADIUS,SECTIONAL SECTIONAL RADIUS STATION THE DESIGNATION OF THE TRANSVERSE SECTION AT WHICH THE PITCH IS MEASURED. 1B MODE REPLY 0 AMXND 19FINISH,MARKING MARKING FINISH AN INDICATION OF THE MARKING FINISH ON THE ITEM. SELECT REPLY CODE 10AB54 AMXPB 04ANGLE IN DEG,BLADE BLADE ANGLE IN DEG THE ANGLE OF BLADE PITCH MEASURED FROM THE PLANE OF ROTATION AT A SPECIFIED LOCATION,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AMXQF T04ANGLE RANGE IN DEG,BLADE BLADE ANGLE RANGE IN DEG THE LIMITS OF BLADE PITCH ANGLE CHANGE FROM THE LOWEST TO THE HIGHEST,WITHIN WHICH THE ITEM WILL OPERATE,MEASURED FROM THE PLANE OF ROTATION AT A SPECIFIED LOCATION,EXPRESSED IN DEGREES. 1F MODE REPLY 0 AMXRJ 04RADIUS,STATION,CONSTANT,DESIGN DESIGN CONSTANT STATION RADIUS THE DESIGN DISTANCE FROM THE AXIS OF ROTATION TO THE STATION OR POINT ON THE THRUST FACE OF THE BLADE AT WHICH THE BLADE ANGLES ARE SET OR MEASURED. 1D AND 1B MODE REPLY11AA05 AMXSD 11METHOD,CONTROL,ICE ICE CONTROL METHOD THE MEANS USED TO CONTROL THE FORMATION OF ICE ON THE ITEM. SELECT REPLY CODE 10AJ30 AMXTD 19MEDIA,CONTROL,ICE ICE CONTROL MEDIA AN INDICATION OF THE SERVICE USED TO CONTROL ICE FORMATION ON THE ITEM. SELECT REPLY CODE 10AB75 AMXWD 08LOCATION,SOURCE,POWER POWER SOURCE LOCATION INDICATES THE PHYSICAL LOCATION OF THE POWER SOURCE IN RELATION TO THE ITEM. SELECT REPLY CODE 10AJ91 AMXXJ /D/ 19LEGEND A LEGEND A NONE. 2D AND 1B MODE REPLY21AA051AC20 AMXYJ /D/ 19LEGEND B LEGEND B NONE. 2D AND 1B MODE REPLY21AA051AC20 AMXZJ /D/ 19LEGEND C LEGEND C NONE. 2D AND 1B MODE REPLY21AA051AC20 AMYAJ /D/ 19LEGEND D LEGEND D NONE. 2D AND 1B MODE REPLY21AA051AC20 AMYBJ /D/ 19LEGEND E LEGEND E NONE. 2D AND 1B MODE REPLY21AA051AC20 AMYCJ /D/ 19LEGEND A LEGEND A NONE. 2D AND 1B MODE REPLY21AA051AC20 AMYDJ /D/ 19LEGEND B LEGEND B NONE. 2D AND 1B MODE REPLY21AA051AC20 AMYEJ /D/ 19LEGEND C LEGEND C NONE. 2D AND 1B MODE REPLY21AA051AC20 AMYFJ /D/ 19LEGEND D LEGEND D NONE. 2D AND 1B MODE REPLY21AA051AC20 AMYGD /D/ 07MOUNT MOUNT AN INDICATION OF WHETHER OR NOT A MOUNT IS INCLUDED. SELECT REPLY CODE 10AA49 AMYHA 19NUMBER,MODEL,MOUNT MOUNT MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE MOUNT. 1A MODE REPLY 0 AMYJD /D/ 07TRIPOD TRIPOD AN INDICATION OF WHETHER OR NOT A TRIPOD IS INCLUDED. SELECT REPLY CODE 10AA49 AMYKA 19NUMBER,MODEL,TRIPOD TRIPOD MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE TRIPOD. 1A MODE REPLY 0 AMYLD /D/ 07GUN,SPOTTING SPOTTING GUN AN INDICATION OF WHETHER OR NOT A SPOTTING GUN IS INCLUDED. SELECT REPLY CODE 10AA49 AMYMA 19NUMBER,MODEL,SPOTTING GUN SPOTTING GUN MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE SPOTTING GUN. 1A MODE REPLY 0 AMYND 18TYPE,GOVERNOR GOVERNOR TYPE INDICATES THE TYPE OF GOVERNOR PROVIDED. SELECT REPLY CODE 10AJ31 AMYPL 16STYLE,ACCOMMODATION,HUB SHAFT HUB SHAFT ACCOMMODATION STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HUB SHAFT ACCOMMODATION. 1L MODE REPLY 0 AMYQA 12QUANTITY,RING RING QUANTITY THE NUMBER OF RINGS PROVIDED. 1A MODE REPLY 0 AMYRD /D/ 03DESIGNATOR,SIZE,BORE BORE SIZE DESIGNATOR AN ESTABLISHED SIZE DESIGNATION THAT INDICATES THE SPECIFIC DIMENSIONS AND CONFIGURATION OF THE BORE OF THE ITEM. SELECT REPLY CODE 10AJ32 AMYSA 19NUMBER,MODEL,CARRIAGE CARRIAGE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE CARRIAGE. 1A MODE REPLY 0 AMYTJ 10ADJUSTMENT RATING,SPEED SPEED ADJUSTMENT RATING THE VALUE/S/ WHICH EXPRESS THE ADJUSTABLE SPEED/S/ AS APPLIES TO THE OPERATION,OR LIMITATION OF OPERATION,OF AN ITEM. 2D AND 1B MODE REPLY21AA221AC20 AMYWD 18TYPE,BARREL BARREL TYPE AN INDICATION OF THE TYPE OF BARREL INCLUDED. SELECT REPLY CODE 10AC40 AMYXD 18TYPE,DEVICE,STREAMLINING STREAMLINING DEVICE TYPE INDICATES THE STREAMILINING DEVICE INCLUDED ON THE ITEM. SELECT REPLY CODE 10AJ33 AMYYD /D/ 03DESIGNATOR,SIZE,ADAPTER BORE ADAPTER BORE SIZE DESIGNATOR AN ESTABLISHED STANDARD SIZE DESIGNATION WHICH INDICATES THE SPECIFIC DIMENSIONS AND CONFIGURATION OF THE ADAPTER BORE. SELECT REPLY CODE 10AJ32 AMYZD 10STATUS,MOTOR,SPEED ADJUSTMENT SPEED ADJUSTMENT MOTOR STATUS AN INDICATION OF THE MOTOR STATUS FOR SPEED ADJUSTMENT. SELECT REPLY CODE 10AJ34 AMZAA 19NUMBER,MODEL,RECOIL MECHANISM RECOIL MECHANISM MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE RECOIL MECHANISM. 1A MODE REPLY 0 AMZBD /D/ 07VEHICLE,TRANSPORT TRANSPORT VEHICLE AN INDICATION OF WHETHER OR NOT A TRANSPORT VEHICLE IS INCLUDED. SELECT REPLY CODE 10AA49 AMZCA 19NUMBER,MODEL,TRANSPORT VEHICLE TRANSPORT VEHICLE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE TRANSPORT VEHICLE. 1A MODE REPLY 0 AMZDD 11METHOD,REGULATION REGULATION METHOD THE MEANS USED FOR REGULATING THE ITEM. SELECT REPLY CODE 10AE81 AMZEB 10SPEED RATING IN RPM,ROTATIONAL ROTATIONAL SPEED RATING IN RPM THE SPEED AT WHICH AN ITEM HAS BEEN TESTED AND RATED TO PERFORM WITHOUT DAMAGE OR FAILURE OF THE ROTATING COMPONENTS,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 AMZFJ /D/ 10THRUST RATING,REVERSE,MAXIMUM MAXIMUM REVERSE THRUST RATING THE MAXIMUM DRIVING FORCE IN THE LINE OF ITS AXIS,WHEN IN THE REVERSE THRUST CONDITION,AT WHICH THE ITEM WILL SATISFACTORILY PERFORM. 1D AND 1B MODE REPLY12AB16 AMZGJ 04DIAMETER,END,STRIKING STRIKING END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE STRIKING END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AMZHJ /D/ 10THRUST RATING,STATIC,MINIMUM MINIMUM STATIC THRUST RATING THE MINIMUM DRIVING FORCE THAT AN ITEM WILL GENERATE WHILE OPERATING /ROTATING/ WITHOUT TRANSLATION OR AXIAL MOTION. 1D AND 1B MODE REPLY12AB16 AMZJJ 10ABSORPTION RATING,POWER POWER ABSORPTION RATING THE MAXIMUM AMOUNT OF POWER THAT AN ITEM IS DESIGNED TO ABSORB. 1D AND 1B MODE REPLY12AJ35 AMZKB /D/ 10SPEED AT RATED POWER ABSORPTION IN RPM,ROTATIONAL ROTATIONAL SPEED AT RATED POWER ABSORPTION IN RPM THE ROTATIONAL SPEED AT WHICH THE POWER ABSORPTION OF AN ITEM HAS BEEN RATED,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 AMZLG /D/ 19APPLICATION,ENGINE ENGINE APPLICATION THE TYPE AND MODEL NUMBER OF THE ENGINE WITH WHICH THE ITEM IS USED. FULL TEXT WRITE-IN 0 AMZMD 18TYPE,FACILITY,MOUNTING,ACTIVE FACE ACTIVE FACE MOUNTING FACILITY TYPE INDICATES THE TYPE OF MOUNTING FACILITY ON THE ACTIVE FACE. SELECT REPLY CODE 10AJ36 AMZNA 19CODE,MANUFACTURER,BLADE BLADE MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE BLADE. 1A MODE REPLY 0 AMZPA /D/ 19NUMBER,PART,BLADE BLADE PART NUMBER THE IDENTIFYING PART NUMBER ASSIGNED TO THE BLADE. 1A MODE REPLY 0 AMZQJ /D/ 10SETTING AND ANGLE IN DEG,PITCH,SPECIFIED SPECIFIED PITCH SETTING AND ANGLE IN DEG THE PITCH BLADE ANGLE AT WHICH AN ITEM OPERATES UNDER SPECIFIED CONDITIONS,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY13AJ37 AMZRJ 04RADIUS,END,STRIKING STRIKING END RADIUS THE RADIUS OF THE STRIKING END. 2D AND 1B MODE REPLY21AA051AC20 AMZSD 18TYPE,PIN,FIRING FIRING PIN TYPE INDICATES THE TYPE OF FIRING PIN. SELECT REPLY CODE 10AB30 AMZTD /D/ 18TYPE,END,STRIKING STRIKING END TYPE INDICATES THE TYPE OF STRIKING END. SELECT REPLY CODE 10AD07 AMZWD 19MECHANISM HELD MECHANISM HELD INDICATES THE TYPE OF MECHANISM RETAINED. SELECT REPLY CODE 10AJ39 AMZXG 04SPACING AND LOCATION,HOLE,MOUNTING MOUNTING HOLE SPACING AND LOCATION THE MEASURED SPACE BETWEEN THE MOUNTING HOLES AND THE LOCATION. FULL TEXT WRITE-IN 0 AMZYB /D/ 10CURRENT RATING IN AMPS,DC,OPERATING OPERATING DC CURRENT RATING IN AMPS THE LEVEL OF ELECTRICAL FLOW /CURRENT/ FOR WHICH THE ITEM IS DESIGNED,EXPRESSED IN AMPERES. 1B MODE REPLY 0 AMZZJ 10CAPACITY,FLUID,HYDRAULIC SYSTEM HYDRAULIC SYSTEM FLUID CAPACITY THE AMOUNT OF FLUID THAT THE HYDRAULIC SYSTEM WILL HOLD OR THAT IS REQUIRED FROM EXTERNAL SOURCES TO OPERATE THE ITEM. 1D AND 1B MODE REPLY11AB10 ANAAB /D/ 10WATTAGE RATING IN WATTS,SYSTEM,ICE CONTROL ICE CONTROL SYSTEM WATTAGE RATING IN WATTS THE RATED POWER WHICH AN ITEM CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS. 1B MODE REPLY 0 ANABJ /D/ 10FLOW RATE,FLUID,ICE CONTROL ICE CONTROL FLUID FLOW RATE THE AMOUNT PER MINUTE OF FLUID REQUIRED TO OPERATE THE ICE CONTROL SYSTEM. 1D AND 1B MODE REPLY11AC64 ANACJ /D/ 10PRESSURE,FLUID,ICE CONTROL ICE CONTROL FLUID PRESSURE THE GAGE PRESSURE REQUIRED TO OPERATE THE ICE CONTROL SYSTEM. 1D AND 1B MODE REPLY11AA95 ANADD 18TYPE,DEVICE,ELECTRONIC ELECTRONIC DEVICE TYPE INDICATES THE TYPE OF ELECTRONIC DEVICE USED FOR REGULATING THE ITEM. SELECT REPLY CODE 10AG13 ANAED 19COMPENSATION PROVIDED COMPENSATION PROVIDED THE TYPE OF COMPENSATION PROVIDED. SELECT REPLY CODE 10AJ38 ANAFA /D/ 12QUANTITY,HOLE,PILOT PILOT HOLE QUANTITY NONE. 1A MODE REPLY 0 ANAGA /D/ 12QUANTITY,STUD,MOUNTING MOUNTING STUD QUANTITY THE NUMBER OF MOUNTING STUD(S) PROVIDED. 1A MODE REPLY 0 ANAHJ 04LENGTH,OVERALL,HUB HUB OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ANAJJ 04DIAMETER,FACE,FOWARD,HUB HUB FORWARD FACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ANAKJ 04DIAMETER,FACE,AFT,HUB HUB AFT FACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ANALJ 04DIAMETER,MAJOR,TAPER BORE TAPER BORE MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST PORTION OF A TAPERED BORE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ANAMJ 04DIAMETER,MINOR,TAPER BORE TAPER BORE MINOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST PORTION OF A TAPERED BORE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ANANJ 04DIAMETER,COUNTERBORE,FORWARD FORWARD COUNTERBORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ANAPJ 04DEPTH,COUNTERBORE,FORWARD FORWARD COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ANAQJ 04DIAMETER,COUNTERBORE,AFT AFT COUNTERBORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ANARJ 04DEPTH,COUNTERBORE,AFT AFT COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ANASJ 04DIAMETER,FACE,RECESSED,FORWARD FORWARD RECESSED FACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ANATJ 04DEPTH,FACE,RECESSED,FORWARD FORWARD RECESSED FACE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ANAWJ 04DIAMETER,FACE,RECESSED,AFT AFT RECESSED FACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ANAXJ 04DEPTH,FACE,RECESSED,AFT AFT RECESSED FACE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ANAYJ /D/ 04DISTANCE FROM HUB FACE TO FLANGE MOUNTING FACE DISTANCE FROM HUB FACE TO FLANGE MOUNTING FACE NONE. 2D AND 1B MODE REPLY21AA051AC20 ANAZJ 04DIAMETER,COUNTERBORE,MOUNTING HOLE MOUNTING HOLE COUNTERBORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ANBAJ 04DEPTH,COUNTERBORE,HOLE,MOUNTING MOUNTING HOLE COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ANBBJ /D/ 04DIAMETER,CIRCLE,PILOT HOLE PILOT HOLE CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ANBCJ /D/ 10CURRENT,EFFECTIVE EFFECTIVE CURRENT THAT VALUE OF ALTERNATING CURRENT THAT WILL CAUSE THE SAME HEATING EFFECT AS A GIVEN VALUE OF DIRECT CURRENT. 2D AND 1B MODE REPLY21AC301AC20 ANBDB 10PERCENT,REGULATION REGULATION PERCENT THE REGULATED VALUE/S/ OF THE ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 ANBEJ 10TIME,RECOVERY RECOVERY TIME THE TIME REQUIRED FOR THE ITEM TO RECOVER. 1D AND 1B MODE REPLY12AH68 ANBFJ 10RISE ABOVE AMBIENT,TEMP,OPERATING OPERATING TEMP RISE ABOVE AMBIENT THE VALUE WHICH EXPRESSES THE RISE OF THE OPERATING TEMPERATURE ABOVE THE MEDIUM SURROUNDING THE ITEM. 1D AND 1B MODE REPLY11AB36 ANBGJ T10RANGE,OPERATING OPERATING RANGE THE MINIMUM TO MAXIMUM LIMITS OF OPERATION FOR WHICH THE ITEM IS RATED. 1D AND 1F MODE REPLY13AJ40 ANBHD 19RECORDED,INFORMATION INFORMATION RECORDED INDICATES THE TYPE OF INFORMATION THE ITEM WILL RECORD. SELECT REPLY CODE 10AJ41 ANBJJ 10UNIT,GRADUATION GRADUATION UNIT THE INCREMENT OF MEASURE REPRESENTED BY THE MARKING/S/ ON THE ITEM. 1D AND 1B MODE REPLY13AJ40 ANBKD 11METHOD,RECORDING RECORDING METHOD THE MEANS BY WHICH THE ITEM RECORDS INFORMATION. SELECT REPLY CODE 10AJ42 ANBLD 11METHOD,DRIVE,CHART CHART DRIVE METHOD THE MEANS BY WHICH THE CHART IS DRIVEN. SELECT REPLY CODE 10AJ43 ANBMD /D/ 09MATERIAL,SHAFT SHAFT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHAFT IS FABRICATED. PLEASE USE MRC MATT WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 ANBPD 18TYPE,POINT,PEN PEN POINT TYPE INDICATES THE TYPE OF PEN POINT PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AJ44 ANBQD /D/ 07FEATURE,THONG THONG FEATURE AN INDICATION OF WHETHER OR NOT A THONG IS PROVIDED. SELECT REPLY CODE 10AB22 ANBRA 12QUANTITY,GROOVE,RIFLE BORE RIFLE BORE GROOVE QUANTITY THE NUMBER OF RIFLE BORE GROOVE(S) PROVIDED. 1A MODE REPLY 0 ANBSJ 04WIDTH,LAND LAND WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A LAND,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ANBTD 05DIRECTION,RIFLING RIFLING DIRECTION AN INDICATION OF THE RIFLING DIRECTION. SELECT REPLY CODE 10AA38 ANBWD /D/ 09MATERIAL,POINT POINT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE POINT OF THE ITEM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ANBXD /D/ 07RESERVOIR,INK INK RESERVOIR AN INDICATION OF WHETHER OR NOT AN INK RESERVOIR IS INCLUDED. SELECT REPLY CODE 10AA49 ANBYD 07REMOVABILITY,FLANGE FLANGE REMOVABILITY AN INDICATION OF WHETHER OR NOT THE FLANGE IS REMOVABLE. SELECT REPLY CODE 10AC29 ANBZG 12QUANTITY PER RIFLING TURN,CALIBER CALIBER QUANTITY PER RIFLING TURN THE NUMBER OF CALIBERS OF LENGTH IN WHICH THE RIFLING COMPLETE ONE FULL TURN. FULL TEXT WRITE-IN 0 ANCAG /D/ 19SPEC/STD,MATERIAL,TUBE TUBE MATERIAL SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE BASIC TUBE MATERIAL. FULL TEXT WRITE-IN 0 ANCBD /D/ 09MATERIAL,BREECHRING BREECHRING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BREECHRING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ANCCG /D/ 19SPEC/STD,MATERIAL,BREECHRING BREECHRING MATERIAL SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE BASIC BREECHRING MATERIAL. FULL TEXT WRITE-IN 0 ANCDD /D/ 09MATERIAL,BREECHBLOCK BREECHBLOCK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BREECHBLOCK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ANCEG /D/ 19SPEC/STD,MATERIAL,BREECHBLOCK BREECHBLOCK MATERIAL SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE BASIC BREECHBLOCK MATERIAL. FULL TEXT WRITE-IN 0 ANCFA /D/ 12QUANTITY,DEVICE,LOCKING,FIRST END COUPLING FIRST END COUPLING LOCKING DEVICE QUANTITY THE NUMBER OF LOCKING DEVICES INCLUDED ON THE FIRST END COUPLING. 1A MODE REPLY 0 ANCGD 05DIRECTION,OPERATIONAL,BREECHLOCK BREECHBLOCK OPERATIONAL DIRECTION THE SPECIFIC DIRECTION IN WHICH THE BREECHBLOCK MOVES FOR OPERATION. SELECT REPLY CODE 10AA38 ANCHD /D/ 07BRAKE,MUZZLE MUZZLE BRAKE AN INDICATION OF WHETHER OR NOT A MUZZLE BRAKE IS INCLUDED. SELECT REPLY CODE 10AA49 ANCJD /D/ 07SUPPRESSOR,FLASH FLASH SUPPRESSOR AN INDICATION OF WHETHER OF NOT A FLASH SUPPRESSOR IS INCLUDED. SELECT REPLY CODE 10AA49 ANCKD /D/ 07EVACUATOR,BORE BORE EVACUATOR AN INDICATION OF WHETHER OR NOT A BORE EVACUATOR IS INCLUDED. SELECT REPLY CODE 10AA49 ANCMD /D/ 09MATERIAL,INSULATION,OUTER SURFACE OUTER SURFACE INSULATION MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE OUTER SURFACE INSULATION IS FABRICATED. SELECT REPLY CODE 10AD09 ANCND 19CHARACTERISTIC,VOLTAGE,OPERATING OPERATING VOLTAGE CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC OF THE OPERATING VOLTAGE. SELECT REPLY CODE 10AJ45 ANCPD 11METHOD,REDUCTION,VOLTAGE VOLTAGE REDUCTION METHOD THE MEANS USED TO REDUCE THE ELECTRICAL VOLTAGE. SELECT REPLY CODE 10AG91 ANCQD 11METHOD,RESTORING,FULL VOLTAGE FULL VOLTAGE RESTORING METHOD THE MEANS USED TO RESTORE THE ITEM TO ITS FULL VOLTAGE. SELECT REPLY CODE 10AG91 ANCRD /D/ 07BEVEL,END,CONTACT CONTACT END BEVEL INDICATES WHETHER OR NOT A CONTACT END BEVEL IS INCLUDED. SELECT REPLY CODE 10AA49 ANCSD 13THREAD LOCATION,TOP TOP THREAD LOCATION INDICATES THE LOCATION OF THREADS ON THE TOP OF THE ITEM. SELECT REPLY CODE 10AJ91 ANCTD 18TYPE,BLADE BLADE TYPE INDICATES THE TYPE OF BLADE PROVIDED. SELECT REPLY CODE 10AJ46 ANCWD /D/ 07FEATURE,GROOVE,BLOOD,BLADE BLADE BLOOD GROOVE FEATURE AN INDICATION OF WHETHER OR NOT A BLADE BLOOD GROOVE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ANCXD /D/ 18TYPE,CONTROL CONTROL TYPE INDICATES THE TYPE OF CONTROL. SELECT REPLY CODE 10AD65 ANCYB 10HORSEPOWER RATING HORSEPOWER RATING AN INDICATION OF THE RATED HORSEPOWER OF THE ITEM. 1B MODE REPLY 0 ANCZD /D/ 07CAP CAP AN INDICATION OF WHETHER OR NOT A CAP IS INCLUDED. SELECT REPLY CODE 10AA49 ANDAD 18TYPE ACCOMMODATED,SPRING,PRESSURE,BRUSH BRUSH PRESSURE SPRING TYPE ACCOMMODATED INDICATES THE TYPE OF BRUSH PRESSURE SPRING(S) THE ITEM ACCOMMODATES. SELECT REPLY CODE 10AJ47 ANDBD 07ADJUSTABILITY,SPRING,BRUSH BRUSH SPRING ADJUSTABILITY INDICATES WHETHER OR NOT THE BRUSH SPRING IS ADJUSTABLE. SELECT REPLY CODE 10AB00 ANDCD /D/ 07SPRING,PRESSURE,BRUSH BRUSH PRESSURE SPRING INDICATES WHETHER OR NOT A BRUSH PRESSURE SPRING(S) IS INCLUDED. SELECT REPLY CODE 10AA49 ANDDA 12QUANTITY PER ASSEMBLY,HOLDER HOLDER QUANTITY PER ASSEMBLY THE NUMBER OF HOLDERS COMPRISING A HOLDER ASSEMBLY. 1A MODE REPLY 0 ANDEJ 10VOLTAGE,ACTUATOR ACTUATOR VOLTAGE THE VOLTAGE REQUIRED TO ACTUATE THE ITEM. 1D AND 1B MODE REPLY11AB62 ANDFD /D/ 10PHASE,ACTUATOR ACTUATOR PHASE THE NUMBER OF ALTERNATING CURRENT PHASES REQUIRED TO ACTUATE THE ITEM. SELECT REPLY CODE 10AD02 ANDGB 10CURRENT RATING IN AMPS,FUSE FUSE CURRENT RATING IN AMPS THE VALUE OF CURRENT FOR WHICH THE FUSE IS RATED,EXPRESSED IN AMPERES. 1B MODE REPLY 0 ANDHD 19POSITION,GROUPING,ASSEMBLY ASSEMBLY GROUPING POSITION DESIGNATES THE GEOMETRIC ALIGNMENT IN WHICH THE GROUPS ARE POSITIONED. SELECT REPLY CODE 10AJ48 ANDJG /D/ 19CODE AND PART NUMBER,MANUFACTURER,HOLDER HOLDER MANUFACTURER CODE AND PART NUMBER THE NUMERIC CODE OF THE HOLDER MANUFACTURER AND THE PART NUMBER OF THE HOLDER. FULL TEXT WRITE-IN 0 ANDKA 12QUANTITY,GROUP,HOLDER HOLDER GROUP QUANTITY THE NUMBER OF DESIGNATED HOLDER GROUPS. 1A MODE REPLY 0 ANDLA 12QUANTITY,HOLDER,INDIVIDUAL GROUP INDIVIDUAL GROUP HOLDER QUANTITY THE NUMBER OF HOLDERS IN EACH INDIVIDUAL GROUP. 1A MODE REPLY 0 ANDMB 04ANGLE BETWEEN CORRESPONDING HOLDER GROUPS IN DEG ANGLE BETWEEN CORRESPONDING HOLDER GROUPS IN DEG THE ANGULAR MEASUREMENT BETWEEN CORRESPONDING HOLDER GROUPS,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ANDNJ 04DISTANCE BETWEEN HOLDER GROUPS,NOMINAL NOMINAL DISTANCE BETWEEN HOLDER GROUPS A LINEAR MEASUREMENT OF THE NOMINAL DISTANCE BETWEEN HOLDER GROUPS. 1D AND 1B MODE REPLY11AA05 ANDPD 07ADJUSTABILITY,POSITION,HOLDER HOLDER POSITION ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE HOLDER POSITION IS ADJUSTABLE. SELECT REPLY CODE 10AB00 ANDQD /D/ 07SLOTS,POSITIONING,INTEGRAL INTEGRAL POSITIONING SLOTS INDICATES WHETHER OR NOT SLOTS ARE INCLUDED IN THE ITEM FOR POSITIONING PURPOSES. SELECT REPLY CODE 10AA49 ANDRA 12QUANTITY MOUNTED IN PAIRS,GROUP,HOLDER HOLDER GROUP QUANTITY MOUNTED IN PAIRS THE NUMBER OF HOLDER GROUPS MOUNTED TO OPERATE IN PAIRS. 1A MODE REPLY 0 ANDSA 12QUANTITY ACCOMMODATED,BRUSH,TOTAL TOTAL BRUSH QUANTITY ACCOMMODATED THE TOTAL NUMBER OF INDIVIDUAL BRUSHES THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 ANDTA 12QUANTITY ACCOMMODATED PER HOLDER,BRUSH BRUSH QUANTITY ACCOMMODATED PER HOLDER THE NUMBER OF BRUSHES ACCOMMODATED IN EACH HOLDER. 1A MODE REPLY 0 ANDWD 18TYPE,PROTECTION,LOAD LOAD PROTECTION TYPE INDICATES THE TYPE OF LOAD FOR WHICH THE ITEM IS PROTECTED. SELECT REPLY CODE 10AJ49 ANDXJ 10TEMP,AMBIENT AMBIENT TEMP THE TEMPERATURE OF THE MEDIUM SURROUNDING AN ITEM AT WHICH IT CAN BE OPERATED. 1D AND 1B MODE REPLY11AB36 ANDYD 18TYPE,CATCH,GRIP GRIP CATCH TYPE INDICATES THE TYPE OF GRIP CATCH PROVIDED. SELECT REPLY CODE 10AB58 ANDZD /D/ 08LOCATION,ACCESSORY ACCESSORY LOCATION INDICATES THE LOCATION OF THE ACCESSORY/IES/. SELECT REPLY CODE 10AE46 ANEAA 19NUMBER,MODEL,SCABBARD SCABBARD MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE SCABBARD. 1A MODE REPLY 0 ANEBD /D/ 07SCABBARD SCABBARD AN INDICATION OF WHETHER OR NOT A SCABBARD IS INCLUDED. SELECT REPLY CODE 10AA49 ANECG /D/ 19SPEC/STD,MATERIAL,GRIP GRIP MATERIAL SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE BASIC GRIP MATERIAL. FULL TEXT WRITE-IN 0 ANEDD /D/ 09MATERIAL,GRIP GRIP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE GRIP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ANEEJ 04LENGTH,GRIP GRIP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE GRIP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ANEFD /D/ 07ACCESSORY ACCESSORY AN INDICATION OF WHETHER OR NOT THE ACCESSORY(IES) IS INCLUDED. SELECT REPLY CODE 10AA49 ANEGA 12QUANTITY,REGULATOR REGULATOR QUANTITY THE NUMBER OF REGULATOR(S). 1A MODE REPLY 0 ANEHD 03DESIGNATION,DESIGN DESIGN DESIGNATION THE DESIGNATION DERIVED FROM THE NAME OF THE DESIGNER OR USE FOR WHICH THE ITEM IS INTENDED. SELECT REPLY CODE 10AJ50 ANEJJ 04THICKNESS,INSIDE INSIDE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ANEKJ /D/ 04THICKNESS,INSIDE,MAJOR MAJOR INSIDE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ANELJ /D/ 04THICKNESS,INSIDE,MINOR MINOR INSIDE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ANEMJ /D/ 04THICKNESS,OVERALL,MAJOR MAJOR OVERALL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ANENJ /D/ 04THICKNESS,OVERALL,MINOR MINOR OVERALL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ANEPA 12QUANTITY,WING,FLANGED FLANGED WING QUANTITY THE NUMBER OF FLANGED WINGS PROVIDED. 1A MODE REPLY 0 ANEQD 18TYPE,SIGNAL SIGNAL TYPE INDICATES THE TYPE OF SIGNALLING THE ITEM WILL PERFORM. SELECT REPLY CODE 10AJ52 ANERA /D/ 12QUANTITY,EYE,SHAFT SHAFT EYE QUANTITY THE NUMBER OF OPENINGS ALONG THE SIDE OF THE SHAFT DESIGNED FOR DRAINAGE,IRRIGATION,OR INOCULATION. 1A MODE REPLY 0 ANESJ 10CAPACITY,BALLOON BALLOON CAPACITY THE RATED AIR/FLUID VOLUME OF THE BALLOON. 1D AND 1B MODE REPLY12AG67 ANETA 12QUANTITY,FUNNEL,PROXIMAL END PROXIMAL END FUNNEL QUANTITY THE NUMBER OF PROXIMAL END FUNNELS PROVIDED. 1A MODE REPLY 0 ANEXA 12QUANTITY,CASE,CARRYING CARRYING CASE QUANTITY THE NUMBER OF CARRYING CASES INCLUDED. 1A MODE REPLY 0 ANEYA 12QUANTITY,PASSAGE,LUMEN LUMEN PASSAGE QUANTITY THE NUMBER OF LUMEN PASSAGES IN THE BASIC ITEM. 1A MODE REPLY 0 ANFAD 11METHOD,TRANSMISSION,WIND SPEED WIND SPEED TRANSMISSION METHOD THE MEANS USED TO TRANSFER VELOCITY INTO MEASURED INFORMATION. SELECT REPLY CODE 10AJ53 ANFBD /D/ 18TYPE,THREAD,FILIFORM FILIFORM THREAD TYPE THE DESIGNATION PECULIAR TO CATHETERS USED BY THE MANUFACTURERS OF MEDICAL INSTRUMENTS. SELECT REPLY CODE 10AG34 ANFCD /D/ 19DEVICE,INFLATION INFLATION DEVICE THE DEVICE USED TO PERMIT INJECTION OF AIR OR FLUID INTO THE ITEM. SELECT REPLY CODE 10AE34 ANFDD 11METHOD,TRANSMISSION,WIND DIRECTION WIND DIRECTION TRANSMISSION METHOD THE MEANS USED TO TRANSFER WIND DIRECTION INTO USEFUL INFORMATION. SELECT REPLY CODE 10AJ53 ANFED 18TYPE,ROTOR,WIND SPEED WIND SPEED ROTOR TYPE INDICATES THE TYPE OF WIND SPEED ROTOR. SELECT REPLY CODE 10AJ54 ANFFD /D/ 09MATERIAL,ROTOR,WIND SPEED WIND SPEED ROTOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WIND SPEED ROTOR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ANFGD 18TYPE,TIP TIP TYPE INDICATES THE TYPE OF TIP PROVIDED. SELECT REPLY CODE 10AJ55 ANFHD 18TYPE,COMPONENT,WIND DIRECTION WIND DIRECTION COMPONENT TYPE INDICATES THE TYPE OF WIND DIRECTION COMPONENT. SELECT REPLY CODE 10AJ56 ANFJD 18TYPE,CONNECTOR CONNECTOR TYPE INDICATES THE TYPE OF CONNECTOR PROVIDED. SELECT REPLY CODE 10AJ57 ANFKD /D/ 09MATERIAL,COMPONENT,WIND DIRECTION WIND DIRECTION COMPONENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WIND DIRECTION COMPONENT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ANFLL /D/ 16STYLE,FITTING FITTING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FITTING. 1L MODE REPLY 0 ANFMD /D/ 18TYPE,BULB,STOMACH TUBE STOMACH TUBE BULB TYPE INDICATES THE TYPE OF BULB USED AS AN AID TO PREVENT CLOGGING OF THE STOMACH TUBE. SELECT REPLY CODE 10AJ58 ANFND /D/ 07HARDWARE,SUPPORT SUPPORT HARDWARE AN INDICATION OF WHETHER OR NOT SUPPORT HARDWARE IS INCLUDED. SELECT REPLY CODE 10AA49 ANFPJ /D/ 19LEGEND F LEGEND F NONE. 2D AND 1B MODE REPLY21AA051AC20 ANFQD 19GRADUATION,SCALE,ALTITUDE ALTITUDE SCALE GRADUATION THE GRADUATION INDICATED ON THE ALTITUDE SCALE. SELECT REPLY CODE 10AJ59 ANFRJ 10CAPACITY,SYRINGE SYRINGE CAPACITY THE RATED VOLUME OF THE SYRINGE. 1D AND 1B MODE REPLY12AG67 ANFSD 11METHOD,FABRICATION,CORE CORE FABRICATION METHOD THE MEANS USED TO FABRICATE THE CORE. SELECT REPLY CODE 10AA62 ANFTJ 10INCREMENT,SMALLEST,ALTITUDE SCALE ALTITUDE SCALE SMALLEST INCREMENT THE SMALLEST VALUE BETWEEN MARKINGS ON AN ALTITUDE SCALE. 1D AND 1B MODE REPLY11AA05 ANFWD 07ADJUSTABILITY,SCALE,ALTITUDE ALTITUDE SCALE ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE ALTITUDE SCALE IS ADJUSTABLE. SELECT REPLY CODE 10AB00 ANFXJ T10RANGE,SCALE,ALTITUDE ALTITUDE SCALE RANGE THE VARIATIONS OF HEIGHT THAT AN ALTITUDE SCALE WILL MEASURE. 1D AND 1F MODE REPLY11AA05 ANFYD /D/ 03DESIGNATION,SIZE,PATIENT PATIENT SIZE DESIGNATION THE NONNUMERIC DESIGNATION STANDARDIZED ON AGE,SEX,AND SIZE AS RELATING TO BODY PROPORTIONMENTS. SELECT REPLY CODE 10AJ60 ANFZJ /D/ 19LEGEND G LEGEND G NONE. 2D AND 1B MODE REPLY21AA051AC20 ANGAJ /D/ 19LEGEND H LEGEND H NONE. 2D AND 1B MODE REPLY21AA051AC20 ANGBJ /D/ 19LEGEND I LEGEND I NONE. 2D AND 1B MODE REPLY21AA051AC20 ANGCD 19GRADUATION,SCALE,BAROMETER BAROMETER SCALE GRADUATION THE GRADUATION INDICATED ON THE BAROMETER SCALE. SELECT REPLY CODE 10AJ59 ANGDD 07DISPOSITION AFTER INITIAL USE DISPOSITION AFTER INITIAL USE AN INDICATION OF THE DISPOSITION OF AN ITEM AFTER INITIAL USE. SELECT REPLY CODE 10AJ61 ANGEJ 10INCREMENT,SMALLEST,BAROMETER SCALE BAROMETER SCALE SMALLEST INCREMENT THE SMALLEST VALUE BETWEEN MARKINGS ON A BAROMETER SCALE. 1D AND 1B MODE REPLY12AG20 ANGFD /D/ 07MARKINGS,GRADUATION,DEPTH DEPTH GRADUATION MARKINGS AN INDICATION OF WHETHER OR NOT DEPTH GRADUATION MARKINGS ARE INCLUDED. SELECT REPLY CODE 10AA49 ANGGJ T10RANGE,SCALE,BAROMETER BAROMETER SCALE RANGE THE VARIATIONS IN ATMOSPHERIC PRESSURE THAT A BAROMETER SCALE WILL MEASURE. 1D AND 1F MODE REPLY12AG20 ANGHD /D/ 19DEVICE,INTRODUCER INTRODUCER DEVICE A DEVICE USED TO FACILITATE THE INSERTION OF SOFTER,MORE FLEXIBLE MATERIAL/S/. SELECT REPLY CODE 10AJ62 ANGJA /D/ 13THREAD SIZE,FACILITY,MOUNTING MOUNTING FACILITY THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE MOUNTING FACILITY. 1A MODE REPLY 0 ANGKD /D/ 07OPACITY,X-RAY X-RAY OPACITY AN INDICATION OF WHETHER OR NOT MATERIALS,COLORS,LINES,OR BANDS WHICH CAN BE DETECTED BY X-RAYS ARE INCLUDED. SELECT REPLY CODE 10AA49 ANGLB 13SCREW THREAD QUANTITY PER INCH,PORT PORT SCREW THREAD QUANTITY PER INCH A MEASUREMENT OF THE NUMBER OF SCREW THREADS ON THE PORT PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1B MODE REPLY 0 ANGMD 13SCREW THREAD SERIES DESIGNATOR,PORT PORT SCREW THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER OF A PORT. SELECT REPLY CODE 10AH06 ANGNJ 04DIAMETER,BURSTING,MINIMUM MINIMUM BURSTING DIAMETER THE MINIMUM DIAMETER AT WHICH THE ITEM WILL BURST. 1D AND 1B MODE REPLY11AA05 ANGPD 19GRADUATIONS,SPECIAL SPECIAL GRADUATIONS THE SPECIAL SCALE OR INCREMENT MARKINGS INCLUDED ON THE ITEM. SELECT REPLY CODE 10AB44 ANGQJ 10ALTITUDE,BURSTING,MINIMUM MINIMUM BURSTING ALTITUDE THE MINIMUM ALTITUDE AT WHICH THE ITEM WILL BURST. 1D AND 1B MODE REPLY11AA05 ANGRB 10FORCE IN GRAMS,LIFTING LIFTING FORCE IN GRAMS THE AMOUNT OF FORCE THAT MUST BE APPLIED TO THE ITEM TO CAUSE A LIFTING ACTION,EXPRESSED IN GRAMS. 1B MODE REPLY 0 ANGSD 07CONDUCTIVITY CONDUCTIVITY AN INDICATION OF THE ABILITY TO CONDUCT ELECTRICITY. SELECT REPLY CODE 10AJ63 ANGTD 07ADJUSTABILITY,SPEED,PULSE PULSE SPEED ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE PULSE SPEED IS ADJUSTABLE. SELECT REPLY CODE 10AB00 ANGWD 18TYPE,DESIGN,CHARGE CHARGE DESIGN TYPE INDICATES THE DESIGN TYPE OF THE CHARGE. SELECT REPLY CODE 10AJ64 ANGXJ 10SPEED PER SECOND,PULSE PULSE SPEED PER SECOND THE RATE AT WHICH THE PULSES RECUR EACH SECOND. 1D AND 1B MODE REPLY11AC20 ANGYA 19ARRANGEMENT,CONTACT,SHUNT SPRING SHUNT SPRING CONTACT ARRANGEMENT THE DESIGNATION INDICATING THE ARRANGEMENT OF SHUNT SPRING CONTACTS. 1A MODE REPLY 0 ANGZD /D/ 09MATERIAL,PLATE,NUMBER NUMBER PLATE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE NUMBER PLATE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ANHAD 09MATERIAL,FILLER FILLER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF THE FILLER MATERIAL. SELECT REPLY CODE 10AF45 ANHBA 12QUANTITY,INCREMENT INCREMENT QUANTITY THE NUMBER OF INCREMENT(S) WHICH MAKE UP THE ITEM. 1A MODE REPLY 0 ANHCD 18TYPE,CHARACTER CHARACTER TYPE INDICATES THE TYPE OF CHARACTERS ON THE ITEM. SELECT REPLY CODE 10AJ65 ANHDD /D/ 09MATERIAL,WHEEL,FINGER FINGER WHEEL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FINGER WHEEL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ANHED /D/ 07WELL,ACTIVATOR ACTIVATOR WELL AN INDICATION OF WHETHER OR NOT AN ACTIVATOR WELL IS INCLUDED. PLEASE USE MRC ABFF OR AKYN INPLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 ANHFJ /D/ 04DIAMETER,NOMINAL NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AF98 ANHGJ /D/ 04SIZE,NOMINAL,HEAD HEAD NOMINAL SIZE NONE. 1D AND 1B MODE REPLY11AF98 ANHHJ /D/ 04LENGTH,NOMINAL,ANGLE ANGLE NOMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AF98 ANHJJ /D/ 04LENGTH,NOMINAL,HORIZONTAL BAR HORIZONTAL BAR NOMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AF98 ANHKJ /D/ 04LENGTH,NOMINAL,VERTICAL BAR VERTICAL BAR NOMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AF98 ANHLJ /D/ 04DIAMETER,NOMINAL,SPLINT SPLINT NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AF98 ANHMJ /D/ 04DIAMETER,NOMINAL,NEEDLE NEEDLE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A NEEDLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AF98 ANHNJ /D/ 04LENGTH,NOMINAL,NEEDLE GUARD NEEDLE GUARD NOMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AF98 ANHPJ /D/ 04LENGTH,NOMINAL,NEEDLE NEEDLE NOMINAL LENGTH A MEASUREMENT OF THE LONGEST NOMINAL DIMENSION OF A NEEDLE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AF98 ANHQJ /D/ 04LENGTH,NOMINAL,CATHETER CATHETER NOMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AF98 ANHRA 12QUANTITY,HOLE,FINGER WHEEL FINGER WHEEL HOLE QUANTITY THE NUMBER OF HOLES IN THE FINGER WHEEL. 1A MODE REPLY 0 ANHSA 04SIZE,CONNECTION,FILLER FILLER CONNECTION SIZE DESIGNATES THE SIZE OF THE FILLER CONNECTION INCLUDED ON THE ITEM. 1A MODE REPLY 0 ANHTA 04SIZE,CONNECTION,HELMET HELMET CONNECTION SIZE DESIGNATES THE SIZE OF THE HELMET CONNECTION INCLUDED ON THE ITEM. 1A MODE REPLY 0 ANHWA 04SIZE,CONNECTION,MASK MASK CONNECTION SIZE DESIGNATES THE SIZE OF THE MASK CONNECTION INCLUDED ON THE ITEM. 1A MODE REPLY 0 ANHXA /D/ 04SIZE,CONNECTION,SUIT SUIT CONNECTION SIZE DESIGNATES THE SIZE OF THE SUIT CONNECTION INCLUDED ON THE ITEM. 1A MODE REPLY 0 ANHYA 04SIZE,CONNECTION,INLET INLET CONNECTION SIZE DESIGNATES THE SIZE OF THE INLET CONNECTION INCLUDED ON THE ITEM. 1A MODE REPLY 0 ANHZD 19STRENGTH,CONCENTRATED CONCENTRATED STRENGTH AN INDICATION OF THE CONCENTRATED POTENCY OF THE ITEM. SELECT REPLY CODE 10AJ66 ANJAA 12QUANTITY,PAIR,CONDUCTOR,MAXIMUM MAXIMUM CONDUCTOR PAIR QUANTITY THE MAXIMUM NUMBER OF PAIRS OF CONDUCTORS ON THE ITEM. 1A MODE REPLY 0 ANJBD /D/ 07CONNECTION,CROSS,FACTORY FACTORY CROSS CONNECTION AN INDICATION OF WHETHER OR NOT CROSS CONNECTION WAS ACCOMPLISHED AT THE FACTORY. SELECT REPLY CODE 10AA49 ANJCA 12QUANTITY,PROTECTOR PROTECTOR QUANTITY THE NUMBER OF PROTECTORS INCLUDED ON THE ITEM. 1A MODE REPLY 0 ANJDD 18TYPE,FACILITY,STORAGE STORAGE FACILITY TYPE INDICATES THE TYPE OF FACILITY(IES) PROVIDED FOR STORAGE. SELECT REPLY CODE 10AJ67 ANJEA 12QUANTITY,FACILITY,STORAGE STORAGE FACILITY QUANTITY THE NUMBER OF STORAGE FACILITIES PROVIDED. 1A MODE REPLY 0 ANJFD /D/ 07PROVISION,WIRING WIRING PROVISION AN INDICATION OF WHETHER OR NOT WIRING PROVISIONS ARE INCLUDED. SELECT REPLY CODE 10AA49 ANJGD /D/ 09MATERIAL,PANEL PANEL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PANEL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC CYJS IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 ANJHJ 10YIELD,PACKAGE,UNIT UNIT PACKAGE YIELD THE YIELD PER PACKAGE UNIT,WHEN MIXED AS RECOMMENDED. 1D AND 1B MODE REPLY12AB16 ANJJJ 10SEPARATION,FREQUENCY,CHANNEL CHANNEL FREQUENCY SEPARATION AN INDICATION OF THE FREQUENCY SPACING BETWEEN CHANNELS. 1D AND 1B MODE REPLY11AC32 ANJKF T10RANGE IN HERTZ,FREQUENCY,AUDIO AUDIO FREQUENCY RANGE IN HERTZ THE FREQUENCY RANGE OF AUDIO SIGNALS FOR WHICH THE ITEM IS RATED,EXPRESSED IN HERTZ. 1F MODE REPLY 0 ANJLL 16STYLE,HOUSING HOUSING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HOUSING. 1L MODE REPLY 0 ANJMJ 04LENGTH,SURFACE,BEARING BEARING SURFACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BEARING SURFACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ANJND 18TYPE,MOTOR MOTOR TYPE INDICATES THE TYPE OF MOTOR PROVIDED. SELECT REPLY CODE 10AJ71 ANJPD 19LEVEL,MONOGLYCERIDE MONOGLYCERIDE LEVEL INDICATES THE LEVEL OF MONOGLYCERIDE IN THE ITEM. SELECT REPLY CODE 10AE25 ANJQD 07CHARACTERISTIC,STABILITY STABILITY CHARACTERISTIC AN INDICATION OF THE STABILITY CHARACTERISTIC(S) OF THE ITEM. SELECT REPLY CODE 10AH10 ANJRB /D/ 04ANGLE FROM HORIZONTAL CENTERLINE IN DEG,FITTING,LUBRICATION LUBRICATION FITTING ANGLE FROM HORIZONTAL CENTERLINE IN DEG THE ANGLE OF THE FITTING FROM THE HORIZONTAL CENTERLINE OF THE ITEM,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ANJSD 18TYPE,END,SHAFT SHAFT END TYPE INDICATES THE TYPE OF SHAFT END PROVIDED. SELECT REPLY CODE 10AC59 ANJTA 12QUANTITY,PORT,CONNECTION CONNECTION PORT QUANTITY THE NUMBER OF CONNECTION PORTS PROVIDED ON THE ITEM. 1A MODE REPLY 0 ANJWD 18TYPE,CONNECTION,PORT PORT CONNECTION TYPE INDICATES THE TYPE OF PORT CONNECTION(S) PROVIDED. SELECT REPLY CODE 10AJ68 ANJXJ /D/ 04DIAMETER,ACCOMMODATION,HOSE HOSE ACCOMMODATION DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOSE ACCOMMODATION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ANJYJ 04DIAMETER,ACCOMMODATION,PIPE PIPE ACCOMMODATION DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PIPE ACCOMMODATION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ANJZJ 04DIAMETER,OUTSIDE,TUBE ACCOMMODATION TUBE ACCOMMODATION OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBE ACCOMMODATION,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ANKAB /D/ 04ANGLE IN DEG,SEAT,CONNECTION CONNECTION SEAT ANGLE IN DEG THE ANGLE OF THE CONNECTION END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ANKBD 18TYPE,COMPRESSION COMPRESSION TYPE INDICATES THE TYPE OF COMPRESSION FURNISHED. SELECT REPLY CODE 10AJ70 ANKCA 13THREAD SIZE,CONNECTION CONNECTION THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE CONNECTION. 1A MODE REPLY 0 ANKDD /D/ 07ADDITIVE,COLORING COLORING ADDITIVE AN INDICATION OF WHETHER OR NOT THE ITEM HAS A COLORING ADDITIVE INCLUDED. SELECT REPLY CODE 10AA49 ANKED /D/ 19FINISH,SURFACE,ROLLING ELEMENT GROOVE ROLLING ELEMENT GROOVE SURFACE FINISH AN INDICATION OF THE SURFACE FINISH OF THE ROLLING ELEMENT GROOVE/S/. SELECT REPLY CODE 10AA41 ANKFD 08LOCATION,SEAL SEAL LOCATION INDICATES THE LOCATION OF THE SEAL. SELECT REPLY CODE 10AJ91 ANKGD /D/ 18TYPE,BLOCK,BEARING BEARING BLOCK TYPE INDICATES THE TYPE OF BEARING BLOCK. SELECT REPLY CODE 10AE90 ANKHD 08LOCATION,COLLAR COLLAR LOCATION INDICATES THE LOCATION OF THE COLLAR. SELECT REPLY CODE 10AJ91 ANKJB 12QUANTITY,INTERVAL,UNIT UNIT INTERVAL QUANTITY THE TRANSMISSION MEDIUM CHARACTERISTIC DETERMINED BY FREQUENCY RESPONSE PER SECOND EXPRESSED IN BAUDS. 1B MODE REPLY 0 ANKKD 18TYPE,CAPABILITY,LOAD LOAD CAPABILITY TYPE INDICATES THE TYPE OF LOAD CAPABILITY. SELECT REPLY CODE 10AJ72 ANKLD 08LOCATION,SURFACE,THRUST BEARING THRUST BEARING SURFACE LOCATION INDICATES THE LOCATION OF THE THRUST BEARING SURFACE. SELECT REPLY CODE 10AJ91 ANKMD /D/ 07REMOVABILITY,LINER LINER REMOVABILITY AN INDICATION OF WHETHER OR NOT THE LINER IS REMOVABLE. SELECT REPLY CODE 10AC29 ANKND /D/ 08LOCATION,MEDIUM,COOLING COOLING MEDIUM LOCATION INDICATES THE LOCATION OF THE COOLING MEDIUM. USE MRC ACZV AND ISAC TO TABLE 0094 SELECT REPLY CODE 10AJ91 ANKPJ 04HEIGHT FROM BOTTOM OF BASE TO BORE CENTERLINE HEIGHT FROM BOTTOM OF BASE TO BORE CENTERLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 ANKQJ /D/A16STYLE AND LOCATION,GROOVE GROOVE STYLE AND LOCATION THE STYLE DESIGNATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE GROOVE,AND ITS LOCATION. 1D AND 1A MODE REPLY12AE46 ANKRD 18TYPE,MECHANISM,RECOIL RECOIL MECHANISM TYPE INDICATES THE TYPE OF RECOIL MECHANISM. SELECT REPLY CODE 10AJ73 ANKSG 10TRAVEL,RECOIL,NORMAL NORMAL RECOIL TRAVEL THE NORMAL DISTANCE THE ITEM IS DESIGNED TO TRAVEL DURING OPERATION. FULL TEXT WRITE-IN 0 ANKTG 10TRAVEL,RECOIL,MAXIMUM MAXIMUM RECOIL TRAVEL THE MAXIMUM DISTANCE THE ITEM IS DESIGNED TO TRAVEL DURING OPERATION. FULL TEXT WRITE-IN 0 ANKWH /D/ 19FACILITY AND COMPONENT ACCOMMODATED,ATTACHMENT ATTACHMENT FACILITY AND COMPONENT ACCOMMODATED INDICATES THE TYPE OF FACILITY PROVIDED FOR ATTACHMENT OF COMPONENT PARTS. 2D MODE REPLY 23AJ743AJ75 ANKXD 18TYPE,EMISSION EMISSION TYPE A CLASSIFICATION OF RADIO FREQUENCY EMISSIONS IN WHICH THE TYPE OF MODULATION,TRANSMISSION,AND/OR SUPPLEMENTARY CHARACTERISTICS ARE REPRESENTED BY SYMBOLS. SELECT REPLY CODE 10AJ76 ANKYD /D/ 11METHOD,BONDING,INSULATING GLASS INSULATING GLASS BONDING METHOD THE MEANS USED TO BOND TWO PIECES OF GLASS TO CREATE AN INSULATING AIR SPACE. SELECT REPLY CODE 10AG85 ANKZJ 10FREQUENCY RATING,RADIO RADIO FREQUENCY RATING THE NUMBER OF COMPLETE CYCLE CHANGES OF RADIATED ELECTROMAGNETIC ENERGY,PER UNIT OF TIME,FOR WHICH AN ITEM IS RATED. 2D AND 1B MODE REPLY21AC321AC20 ANLAD 03DESIGNATION,SIZE,WEAPON WEAPON SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE WEAPON IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. SELECT REPLY CODE 10AF81 ANLBA 19NUMBER,MODEL,WEAPON WEAPON MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE WEAPON. 1A MODE REPLY 0 ANLCA 12QUANTITY,BAND,FREQUENCY FREQUENCY BAND QUANTITY THE NUMBER OF SPECIFIED RANGES OF FREQUENCIES OR WAVELENGTHS OPERATING BETWEEN TWO STATED LIMITS. 1A MODE REPLY 0 ANLDA 12QUANTITY,CHANNEL,FREQUENCY FREQUENCY CHANNEL QUANTITY THE NUMBER OF TRANSMISSION PATHS IN THE ITEM. 1A MODE REPLY 0 ANLEJ 10FREQUENCY,CHANNEL,INDIVIDUAL INDIVIDUAL CHANNEL FREQUENCY THE SPECIFIC FREQUENCY(IES) FOR EACH INDIVIDUAL TRANSMISSION PATH. 2D AND 1B MODE REPLY21AC321AC20 ANLFD /D/ 07TRANSMITTER,CONTROLLED,CRYSTAL CRYSTAL CONTROLLED TRANSMITTER AN INDICATION OF WHETHER OR NOT A CRYSTAL CONTROLLED TRANSMITTER IS INCLUDED. SELECT REPLY CODE 10AA49 ANLGA /D/ 12QUANTITY,CRYSTAL CRYSTAL QUANTITY THE NUMBER OF CRYSTALS INCLUDED. 1A MODE REPLY 0 ANLHJ 10OUTPUT RATING,POWER POWER OUTPUT RATING THE RATED POWER OUTPUT FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AC33 ANLJB 10VOLTAGE RATING IN VOLTS,BATTERY BATTERY VOLTAGE RATING IN VOLTS THE ELECTRIC POTENTIAL THAT A BATTERY CAN PROVIDE,EXPRESSED IN VOLTS. 1B MODE REPLY 0 ANLKJ 04WIDTH,NOTCH NOTCH WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE NOTCH,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ANLLJ 04HEIGHT,BLADE BLADE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BLADE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 ANLMJ 04DISTANCE FROM BASE TO FOOT END DISTANCE FROM BASE TO FOOT END NONE. 2D AND 1B MODE REPLY21AA051AC20 ANLNJ /D/ 04SIZE FOR WHICH DESIGNED,CHAIN CHAIN SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE CHAIN FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 ANLPJ 04DIAMETER,CONE CONE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CONE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ANLQA 19NUMBER,MODEL,CONTAINER CONTAINER MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE CONTAINER. 1A MODE REPLY 0 ANLRD 14SHAPE,CROSS-SECTIONAL CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE ITEM WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 ANLSJ 10AXIS,MINOR,CORE CORE MINOR AXIS A MEASUREMENT OF THE SMALLER OR NARROWER GIRTH OF THE CORE CENTER. 2D AND 1B MODE REPLY21AA051AC20 ANLTJ 10AXIS,MAJOR,CORE CORE MAJOR AXIS A MEASUREMENT OF THE LARGER OR WIDER GIRTH OF THE CORE CENTER. 2D AND 1B MODE REPLY21AA051AC20 ANLWD 19CONDITION TRANSMITTED,METEOROLOGICAL METEOROLOGICAL CONDITION TRANSMITTED THE ATMOSPHERIC MEDIUM THE ITEM IS DESIGNED TO TRANSMIT. SELECT REPLY CODE 10AJ41 ANLXJ 04DIAMETER,OUTSIDE,ATTACHMENT END ATTACHMENT END OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ANLYJ /D/ 04DIAMETER,INSIDE,ATTACHMENT END ATTACHMENT END INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ANLZJ T10RANGE,TRANSMISSION,METEOROLOGICAL CONDITION METEOROLOGICAL CONDITION TRANSMISSION RANGE THE MEASURED RANGE OF ATMOSPHERIC MEDIUM THE ITEM IS DESIGNED TO TRANSMIT. 1D AND 1F MODE REPLY13AJ40 ANMAJ 04WIDTH,BUTT BUTT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ANMBD 18TYPE,CARRIER CARRIER TYPE INDICATES THE TYPE OF CARRIER USED WITH THE ITEM. SELECT REPLY CODE 10AJ77 ANMCJ 04DIAMETER,ATTACHMENT,SAFETY SAFETY ATTACHMENT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ANMDJ 04DIAMETER,HOLE,PIVOT PIVOT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PIVOT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ANMEJ 04DISTANCE FROM END,PIVOT HOLE PIVOT HOLE DISTANCE FROM END NONE. 2D AND 1B MODE REPLY21AA051AC20 ANMFD 11METHOD,OPERATION,WIND SPEED COMPONENT WIND SPEED COMPONENT OPERATION METHOD THE MEANS USED TO CONVERT WIND SPEED INTO MEASURABLE INFORMATION. SELECT REPLY CODE 10AJ78 ANMGD 11METHOD,OPERATION,DIRECTION COMPONENT,WIND WIND DIRECTION COMPONENT OPERATION METHOD THE MEANS USED TO CONVERT WIND DIRECTION INTO MEASURABLE INFORMATION. SELECT REPLY CODE 10AJ78 ANMHD 18TYPE,TAPE,RECORDING RECORDING TAPE TYPE INDICATES THE TYPE OF RECORDING TAPE USED ON THE ITEM. SELECT REPLY CODE 10AJ79 ANMJD 13THREAD STRUCTURE THREAD STRUCTURE AN INDICATION OF THE THREAD STRUCTURE. SELECT REPLY CODE 10AA39 ANMKD 18TYPE,FEED,TAPE TAPE FEED TYPE INDICATES THE TYPE OF TAPE FEED USED ON THE ITEM. SELECT REPLY CODE 10AJ80 ANMLA 12QUANTITY PER LINE,CHARACTER CHARACTER QUANTITY PER LINE THE NUMBER OF CHARACTERS PER LINE. 1A MODE REPLY 0 ANMMD 13THREAD FORMING METHOD THREAD FORMING METHOD THE MEANS USED IN FORMING THE THREAD. SELECT REPLY CODE 10AA62 ANMND 19LANGUAGE,KEYBOARD KEYBOARD LANGUAGE AN INDICATION OF THE LANGUAGE OF THE KEYBOARD. SELECT REPLY CODE 10AH92 ANMPD 18TYPE,CHAMFER,STARTING STARTING CHAMFER TYPE INDICATES THE TYPE OF STARTING CHAMFER. SELECT REPLY CODE 10AJ81 ANMQA 12QUANTITY,CHANNEL CHANNEL QUANTITY THE NUMBER OF CHANNELS ON THE ITEM. 1A MODE REPLY 0 ANMRD 18TYPE,SERVICE,CHANNEL CHANNEL SERVICE TYPE INDICATES THE TYPE OF SERVICE FOR WHICH THE CHANNEL WAS DESIGNED. SELECT REPLY CODE 10AJ82 ANMSJ 04LENGTH CAPABILITY,MAXIMUM THREADING MAXIMUM THREADING LENGTH CAPABILITY THE MAXIMUM LENGTH OF STRAIGHT THREADS THE ITEM IS DESIGNED TO CUT. 1D AND 1B MODE REPLY11AA05 ANMTD 18TYPE,EQUALIZER EQUALIZER TYPE INDICATES THE TYPE OF EQUALIZER. SELECT REPLY CODE 10AJ83 ANMWA 12QUANTITY,HEAD HEAD QUANTITY THE NUMBER OF HEADS PROVIDED. 1A MODE REPLY 0 ANMXD 18TYPE,MODEM MODEM TYPE INDICATES THE SPECIFIC TYPE OF MODEM. SELECT REPLY CODE 10AJ84 ANMYD 07ADJUSTABILITY,HEAD HEAD ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE HEAD IS ADJUSTABLE. SELECT REPLY CODE 10AB00 ANMZD /D/ 07CELL,ARMING ARMING CELL AN INDICATION OF WHETHER OR NOT AN ARMING CELL IS INCLUDED. SELECT REPLY CODE 10AA49 ANNBA 19NUMBER,MODEL,ARMING CELL ARMING CELL MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMOBLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE ARMING CELL. 1A MODE REPLY 0 ANNCJ T18TYPE AND RANGE,DIAL DIAL TYPE AND RANGE INDICATES THE TYPE OF DIAL AND THE MINIMUM AND MAXIMUM CAPACITY IT CAN MEASURE. 1D AND 1F MODE REPLY13AJ41 ANNDG /D/ 10DELAY,TIME TIME DELAY A MEASUREMENT OF ELAPSED TIME. FULL TEXT WRITE-IN 0 ANNED /D/ 11METHOD,ACTIVATION ACTIVATION METHOD THE MEANS USED TO ACTIVATE THE ITEM. SELECT REPLY CODE 10AJ85 ANNFA 12QUANTITY,SPOOL,TRIP WIRE TRIP WIRE SPOOL QUANTITY THE NUMBER OF SPOOLS ON WHICH THE TRIP WIRE IS WOUND. 1A MODE REPLY 0 ANNGJ /D/ 10CONSUMPTION RATE,STEAM STEAM CONSUMPTION RATE THE RATE AT WHICH STEAM IS CONSUMED BY THE PRIME MOVER WHEN OPERATING AT FULL CAPACITY. 1D AND 1B MODE REPLY12AJ86 ANNHA 19NUMBER,MODEL,FIRING DEVICE FIRING DEVICE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE FIRING DEVICE. 1A MODE REPLY 0 ANNJD 03DESIGNATION,STRENGTH STRENGTH DESIGNATION THE DESIGNATION REPRESENTING THE INTENSITY OR FORCE THE ITEM IS CAPABLE OF EXERTING. SELECT REPLY CODE 10AJ87 ANNKJ T13THREAD DIAMETER RANGE ACCOMMODATED THREAD DIAMETER RANGE ACCOMMODATED INDICATES THE THREAD DIAMETER RANGE FOR WHICH THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1F MODE REPLY11AA05 ANNLJ 04LENGTH,END,SQUARE SQUARE END LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SQUARE END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ANNMD 18TYPE,HUB HUB TYPE INDICATES THE TYPE OF HUB PROVIDED. SELECT REPLY CODE 10AJ88 ANNND 03DESIGNATION,THICKNESS,WALL,CANNULA CANNULA WALL THICKNESS DESIGNATION THE DESIGNATION OF THE WALL THICKNESS OF THE CANNULA. SELECT REPLY CODE 10AJ89 ANNPD 03DESIGNATION,BEVEL,CANNULA CANNULA BEVEL DESIGNATION THE DESIGNATION APPLIED TO THE SLANT OR INCLINATION OF THE CANNULA AT THE INJECTION POINT. SELECT REPLY CODE 10AJ90 ANNQH /D/ 09MATERIAL AND LOCATION MATERIAL AND LOCATION THE ELEMENT, COMPOUND, OR MIXTURE OF WHICH THE ITEM IS FABRICATED, EXCLUDINGANY SURFACE TREATMENT, AND ITS LOCATION. PLEASE USE MRC MATT WITH ISAC IN PLACE OF THIS DISCONTINUED MRC. 2D MODE REPLY 26AD093AJ91 ANNRH /D/ 17SURFACE TREATMENT AND LOCATION SURFACE TREATMENT AND LOCATION THE PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF.PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE ITEM AND ITS LOCATION. PLEASE USE MRC SFTT WITH ISAC CODING IN PLACE OF THIS DISCONTINUED MRC. 2D MODE REPLY 26AD093AJ91 ANNSH /D/ 03DESIGNATION AND LOCATION,GAGE,NEEDLE CANNULA NEEDLE CANNULA GAGE DESIGNATION AND LOCATION A UNIVERSAL STANDARD STUBS NEEDLE GAGE DESIGNATION REPRESENTING THE OUTSIDE DIAMETER OF THE NEEDLE CANNULA AND ITS LOCATION ON THE ITEM. 2D MODE REPLY 23AJ923AJ91 ANNTD 07ADJUSTABILITY,STOP,SECURITY SECURITY STOP ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE SECURITY STOP IS ADJUSTABLE. SELECT REPLY CODE 10AB00 ANNWD 18TYPE,CONTAINER,IMMEDIATE IMMEDIATE CONTAINER TYPE INDICATES THE TYPE OF CONTAINER WITH WHICH THE ITEM IS IN DIRECT CONTACT. SELECT REPLY CODE 10AE96 ANNXA 12QUANTITY,CONTAINER,IMMEDIATE IMMEDIATE CONTAINER QUANTITY THE NUMBER OF IMMEDIATE CONTAINERS. 1A MODE REPLY 0 ANNYA 12QUANTITY WITHIN EACH IMMEDIATE CONTAINER QUANTITY WITHIN EACH IMMEDIATE CONTAINER THE NUMBER OF ITEMS WITHIN EACH IMMEDIATE CONTAINER. 1A MODE REPLY 0 ANNZH /D/ 19CODE AND LOCATION,COLOR,IDENTIFICATION IDENTIFICATION COLOR CODE AND LOCATION THE APPLICATION OF COLOR OR A SERIES OF COLORS FOR THE PURPOSE OF IDENTIFYING THE ITEM FOR A SPECIFIC PURPOSE OR FUNCTION,AND A DESIGNATION OF THAT PORTION OF AN ITEM TO WHICH A SPECIFIC COLOR IS APPLICABLE. 2D MODE REPLY 26AD063AJ91 ANPAJ /D/ 04DIAMETER,OUTSIDE,CANNULA CANNULA OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ANPBJ 04DIAMETER,INSIDE,CANNULA CANNULA INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ANPCJ 04LENGTH,CANNULA CANNULA LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CANNULA,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ANPDJ 04DIAMETER,KNOB KNOB DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE KNOB,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ANPEJ 04THICKNESS,KNOB KNOB THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ANPFJ /D/ 04DIAMETER,OUTSIDE,INNER CANNULA INNER CANNULA OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ANPGJ /D/ 04LENGTH BEYOND OUTER CANNULA END,PROTRUSION,INNER CANNULA INNER CANNULA PROTRUSION LENGTH BEYOND OUTER CANNULA END NONE. 2D AND 1B MODE REPLY21AA051AC20 ANPHJ /D/ 04DIAMETER,OUTSIDE,MIDDLE CANNULA MIDDLE CANNULA OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ANPJD 18TYPE,CURRENT,INPUT INPUT CURRENT TYPE INDICATES THE TYPE OF INPUT CURRENT WHETHER ALTERNATING,DIRECT,OR BOTH. SELECT REPLY CODE 10AB62 ANPKJ 10VOLTAGE RATING IN VOLTS,INPUT INPUT VOLTAGE RATING IN VOLTS THE INPUT VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 ANPLJ 10FREQUENCY RATING IN HERTZ,INPUT INPUT FREQUENCY RATING IN HERTZ THE CYCLES PER SECOND /HERTZ/ OF THE INPUT ALTERNATING CURRENT. 1D AND 1B MODE REPLY11AC20 ANPMD 10PHASE,INPUT INPUT PHASE THE NUMBER OF INPUT ALTERNATING CURRENT PHASE(S). SELECT REPLY CODE 10AD02 ANPND 18TYPE,CURRENT,OUTPUT OUTPUT CURRENT TYPE INDICATES THE TYPE OF OUTPUT CURRENT WHETHER ALTERNATING,DIRECT,OR BOTH. SELECT REPLY CODE 10AB62 ANPPJ 10VOLTAGE RATING IN VOLTS,OUTPUT OUTPUT VOLTAGE RATING IN VOLTS THE OUTPUT VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 ANPQJ 10CURRENT RATING,OUTPUT OUTPUT CURRENT RATING THE TOTAL ELECTRICAL OUTPUT CURRENT. 2D AND 1B MODE REPLY21AC301AC20 ANPRA 12QUANTITY,CIRCUIT CIRCUIT QUANTITY THE NUMBER OF ELECTRICAL PATHS PROVIDED ON THE ITEM. 1A MODE REPLY 0 ANPSA 12QUANTITY PER CIRCUIT,CHANNEL,VOICE VOICE CHANNEL QUANTITY PER CIRCUIT THE NUMBER OF CHANNELS FOR VOICE COMMUNICATION THAT ARE PROVIDED PER FUNCTION. 1A MODE REPLY 0 ANPTJ 10POWER RATING POWER RATING THE AMOUNT OF ELECTRICAL ENERGY THAT CAN BE DISSIPATED. 2D AND 1B MODE REPLY21AC331AC20 ANPWJ /D/T10RANGE,VARIATION,LOAD LOAD VARIATION RANGE THE MINIMUM TO MAXIMUM LOAD VARIATION LIMITS FOR WHICH THE ITEM IS DESIGNED. 1D AND 1F MODE REPLY12AE75 ANPXD 19SOURCE,SUPPLY,TRANSMITTER CURRENT TRANSMITTER CURRENT SUPPLY SOURCE AN INDICATION OF THE SOURCE OF THE CURRENT UTILIZED BY THE TRANSMITTER. SELECT REPLY CODE 10AJ93 ANPYD 19DEVICE,SIGNAL,INCOMING CALL INCOMING CALL SIGNAL DEVICE THE DEVICE USED TO SIGNAL INCOMING CALLS. SELECT REPLY CODE 10AJ94 ANPZD 19FEATURE,ENCLOSURE ENCLOSURE FEATURE AN INDICATION OF THE FEATURE/S/ OF THE ENCLOSURE. SELECT REPLY CODE 10AJ95 ANQAD /D/ 08LOCATION,DEVICE,SIGNAL SIGNAL DEVICE LOCATION INDICATES THE LOCATION OF THE SIGNALING DEVICE. SELECT REPLY CODE 10AJ91 ANQBD 19DEVICE,SIGNAL,OUTGOING CALL OUTGOING CALL SIGNAL DEVICE THE DEVICE USED TO SIGNAL OUTGOING CALLS. SELECT REPLY CODE 10AJ96 ANQCD 02DESIGN,NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION STANDARDS NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION STANDARDS DESIGN AN INDICATION OF WHETHER OR NOT THE ITEM IS DESIGNED IN CONFORMANCE WITH THE NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA) STANDARDS. SELECT REPLY CODE 10AJ97 ANQDA 12QUANTITY,REGISTER REGISTER QUANTITY THE NUMBER OF REGISTER(S) CONTAINED IN THE ITEM. 1A MODE REPLY 0 ANQEA 19NUMBER,PERIOD,DELAY DELAY PERIOD NUMBER THE NUMBER OF THE DELAY PERIOD. 1A MODE REPLY 0 ANQFJ 04LENGTH,WIRE,LEAD LEAD WIRE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE LEAD WIRE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ANQGD /D/ 09MATERIAL,WIRE,LEAD LEAD WIRE MATERIAL THE ELEMENT, COMPOUND,OR MIXTURE OF WHICH THE LEAD WIRE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ANQHD /D/ 17SURFACE TREATMENT,WIRE,LEAD LEAD WIRE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A LEAD WIRE SURFACE. SELECT REPLY CODE 10AD09 ANQJA 19NUMBER,MODEL,BLASTING CAP BLASTING CAP MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE BLASTING CAP. 1A MODE REPLY 0 ANQKD 19RESISTANCE,WATER WATER RESISTANCE AN INDICATION OF THE EXTENT TO WHICH THE ITEM CAN RESIST WATER. SELECT REPLY CODE 10AJ98 ANQLB 10STRENGTH IN PERCENT,WEIGHT WEIGHT STRENGTH IN PERCENT THE WEIGHT STRENGTH IN THE ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 ANQMB 10STRENGTH IN PERCENT,CARTRIDGE CARTRIDGE STRENGTH IN PERCENT THE CARTRIDGE STRENGTH IN THE ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 ANQND 19SPEED,CLASSIFICATION,EXPLOSIVE EXPLOSIVE CLASSIFICATION SPEED AN INDICATION OF THE SPEED AT WHICH THE EXPLOSIVE IS CLASSIFIED. SELECT REPLY CODE 10AJ99 ANQPJ 10VELOCITY RATE,DETONATION DETONATION VELOCITY RATE THE RATE OF VELOCITY OF THE DETONATION. 2D AND 1B MODE REPLY22AK001AC20 ANQQA 12QUANTITY PER FIFTY POUNDS,AVERAGE AVERAGE QUANTITY PER FIFTY POUNDS AN INDICATION OF THE AVERAGE NUMBER COMPRISING A WEIGHT OF FIFTY POUNDS. 1A MODE REPLY 0 ANQRD 11METHOD,COATING,PROTECTIVE PROTECTIVE COATING METHOD THE MEANS TO PROTECT THE ITEM WITH A COATING. SELECT REPLY CODE 10AK01 ANQSA 12QUANTITY PER REGISTER,FIGURE FIGURE QUANTITY PER REGISTER THE NUMBER OF DIGITS DISPLAYED ON EACH REGISTER OF THE ITEM. 1A MODE REPLY 0 ANQTJ 04HEIGHT,FIGURE FIGURE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE FIGURE. 2D AND 1B MODE REPLY21AA051AC20 ANQWJ /D/ 04WIDTH,FIGURE FIGURE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A FIGURE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ANQXD 01COLOR,FIGURE FIGURE COLOR THE HUE OR TINT OF THE FIGURE. SELECT REPLY CODE 10AD06 ANQYD /D/ 01COLOR,BACKGROUND,REGISTER REGISTER BACKGROUND COLOR THE HUE OR TINT OF THE REGISTER BACKGROUND. SELECT REPLY CODE 10AD06 ANQZA /D/ 12QUANTITY PER REGISTER,DRUM,ROTATING ROTATING DRUM QUANTITY PER REGISTER THE NUMBER OF ROTATING DRUMS PER REGISTER. 1A MODE REPLY 0 ANRAA /D/ 12QUANTITY PER ROTATING DRUM,ROW,FIGURE FIGURE ROW QUANTITY PER ROTATING DRUM THE NUMBER OF ROWS OF FIGURES CONTAINED ON EACH ROTATING DRUM. 1A MODE REPLY 0 ANRBB /D/ 10SPEED IN RPM,MAXIMUM RATED,SHAFT SHAFT MAXIMUM RATED SPEED IN RPM THE MAXIMUM SPEED AT WHICH THE SHAFT IS DESIGNED TO OPERATE,IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 ANRCB 04ANGLE THROW IN DEG PER COUNT,MINIMUM MINIMUM ANGLE THROW IN DEG PER COUNT THE SMALLEST ANGLE OF THROW REQUIRED TO MAKE ONE COUNT,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ANRDB 10REVOLUTIONS PER COUNT,SHAFT SHAFT REVOLUTIONS PER COUNT THE NUMBER OF SHAFT REVOLUTIONS REQUIRED TO MAKE ONE COUNT. 1B MODE REPLY 0 ANREJ 10COUNT RATE,MAXIMUM MAXIMUM COUNT RATE THE MAXIMUM NUMBER OF COUNTS THE ITEM CAN ACCOMPLISH IN A MEASURED TIME. 1D AND 1B MODE REPLY11AC11 ANRFJ /D/ 10VOLT-AMPERE RATING VOLT-AMPERE RATING THE AMOUNT OF APPARENT POWER,AS DISTINGUISHED FROM TRUE POWER,FOR WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY11AC33 ANRGD /D/ 19INDICATOR,VISUAL,COMPUTATION COMPUTATION VISUAL INDICATOR THE MECHANISM WHICH PROVIDES VISUAL INDICATION OF THE COMPUTATION. SELECT REPLY CODE 10AK02 ANRHB 10SIZE RATING,AMP AMP SIZE RATING THE AMPERE SIZE DESIGNATION FOR SPECIAL DESIGN TYPE ITEMS WHICH ARE RATED IN AMPERE SIZE RATHER THAN HORSEPOWER. 1B MODE REPLY 0 ANRJD 08LOCATION,SURFACE,MOUNTING MOUNTING SURFACE LOCATION INDICATES THE PHYSICAL LOCATION OF THE MOUNTING SURFACE ON THE ITEM. SELECT REPLY CODE 10AJ91 ANRKD 19POSITIONS,FUNCTIONAL,SWITCH SWITCH FUNCTIONAL POSITIONS AN INDICATION OF THE VARIOUS FUNCTIONAL SWITCHING POSITIONS. SELECT REPLY CODE 10AK03 ANRLL 16STYLE,ARRANGEMENT,MOUNTING MOUNTING ARRANGEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE MOUNTING. 1L MODE REPLY 0 ANRMD /D/ 19MECHANISM,DRIVING,SHAFT SHAFT DRIVING MECHANISM THE MECHANISM UTILIZED TO ROTATE THE SHAFT. SELECT REPLY CODE 10AG25 ANRNJ /D/ 04DIAMETER,MECHANISM,DRIVING,SHAFT SHAFT DRIVING MECHANISM DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR SHAFT DRIVING MECHANISM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ANRPD /D/ 18TYPE,ACTION,ELECTRICAL CONTACTOR ELECTRICAL CONTACTOR ACTION TYPE INDICATES THE TYPE OF ACTION THE ELECTRICAL CONTACTOR UTILIZES. SELECT REPLY CODE 10AK04 ANRQB 10PERCENT,REGULATION,FREQUENCY FREQUENCY REGULATION PERCENT THE RATIO OF PERMISSIBLE FREQUENCY DEVIATION FROM THE CONTROLLED CONSTANT VALUE,EXPRESSED IN PERCENT. 1B MODE REPLY 0 ANRRB 10PERCENT,REGULATION,VOLTAGE VOLTAGE REGULATION PERCENT THE RATIO OF PERMISSIBLE VOLTAGE DEVIATION FROM THE CONTROLLED CONSTANT VALUE,EXPRESSED IN PERCENT. 1B MODE REPLY 0 ANRSJ 10POWER RATING,GENERATOR GENERATOR POWER RATING THE RATED POWER THAT AN ITEM CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS,KILOWATTS,OR KILOVOLT-AMPERES. 1D AND 1B MODE REPLY11AC33 ANRTD /D/ 07FEATURE,ASSEMBLY,BOARD BOARD ASSEMBLY FEATURE AN INDICATION OF WHETHER OR NOT A BOARD ASSEMBLY FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ANRWG /D/ 19DATA,RADIONUCLIDES RADIONUCLIDES DATA THE AMOUNT OF THE RADIONUCLIDES AS DETERMINED BY THE TYPE OF MATERIAL AND THE PARTICULAR DEVICE BEING TRANSPORTED. PLEASE USE MRC RADD IN PLACE OF THIS DISCONTINUED MRC. FULL TEXT WRITE-IN 0 ANRXD 14SHAPE,CASE CASE SHAPE THE GENERAL OUTSIDE CONFIGURATION OF THE CASE. SELECT REPLY CODE 10AD07 ANRYD 19CLASSIFICATION,INGREDIENT INGREDIENT CLASSIFICATION AN INDICATION OF THE INGREDIENT THAT HAS BEEN ADDED TO THE ITEM FOR CLASSIFICATION. SELECT REPLY CODE 10AK05 ANRZJ 10STRENGTH STRENGTH THE AMOUNT OF STRENGTH IN THE ITEM. 3D AND 1B MODE REPLY32AG535AG542AG55 ANSAD 10PHASE,WINDING WINDING PHASE THE NUMBER OF ALTERNATING CURRENT WINDING PHASE(S). SELECT REPLY CODE 10AD02 ANSBJ T10RANGE,STRENGTH STRENGTH RANGE THE MINIMUM AND MAXIMUM LIMITS OF STRENGTH IN THE ITEM. 2D AND 1F MODE REPLY22AG535AG54 ANSCD /D/ 07FEATURE,FLOATING FLOATING FEATURE AN INDICATION OF WHETHER OR NOT A FLOATING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ANSDD /D/ 07FEATURE,LANOLIN LANOLIN FEATURE AN INDICATION OF WHETHER OR NOT A LANOLIN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ANSED 18TYPE,ACID,FATTY FATTY ACID TYPE INDICATES THE TYPE OF FATTY ACID OF WHICH THE ITEM IS COMPOSED. SELECT REPLY CODE 10AG54 ANSFD 18TYPE,SOLVENT SOLVENT TYPE INDICATES THE TYPE OF SOLVENT PROVIDED. SELECT REPLY CODE 10AK06 ANSGD /D/ 07ADDITIVE,ROSIN ROSIN ADDITIVE AN INDICATION OF WHETHER OR NOT A ROSIN ADDITIVE IS INCLUDED. SELECT REPLY CODE 10AA49 ANSHB 10PERCENTAGE,ADDITIVE,MAXIMUM MAXIMUM ADDITIVE PERCENTAGE THE ALLOWABLE MAXIMUM ADDITIVE PERCENTAGE. 1B MODE REPLY 0 ANSJD 10TITER RATING TITER RATING AN INDICATION OF THE TITER RATING. SELECT REPLY CODE 10AK07 ANSKJ /D/ 04DISTANCE BETWEEN MOUNTING FACILITIES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES A MEASUREMENT OF THE CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES. 2D AND 1B MODE REPLY21AA051AC20 ANSLJ 10IMPEDANCE RATING,INPUT INPUT IMPEDANCE RATING THE TOTAL OPPOSITON (RESISTIVE AND REACTIVE) WHICH THE ITEM OFFERS TO THE INPUT FLOW OF ALTERNATING CURRENT. 1D AND 1B MODE REPLY12AE75 ANSMA 12QUANTITY,SIGNAL,OUTPUT OUTPUT SIGNAL QUANTITY THE NUMBER OF OUTPUT SIGNAL(S). 1A MODE REPLY 0 ANSND 18TYPE,SIGNAL,OUTPUT OUTPUT SIGNAL TYPE INDICATES THE TYPE OF OUTPUT SIGNAL. SELECT REPLY CODE 10AJ52 ANSPD /D/ 07ADDITIVE,ABRASIVE ABRASIVE ADDITIVE AN INDICATION OF WHETHER OR NOT AN ABRASIVE ADDITIVE IS INCLUDED. SELECT REPLY CODE 10AA49 ANSQJ A10FREQUENCY RATING,OUTPUT OUTPUT FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE OUTPUT FREQUENCY IS RATED. 1D AND 1A MODE REPLY11AC32 ANSRJ 10IMPEDANCE RATING,OUTPUT OUTPUT IMPEDANCE RATING THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) WHICH THE ITEM OFFERS TO THE OUTPUT FLOW OF ALTERNATING CURRENT. 1D AND 1B MODE REPLY12AE75 ANSSD /D/ 18TYPE,ATTACHMENT,JAW JAW ATTACHMENT TYPE INDICATES THE TYPE OF JAWS USED FOR ATTACHING THE ITEM. SELECT REPLY CODE 10AK08 ANSTD /D/ 07FEATURE,INSULATION,JAW JAW INSULATION FEATURE AN INDICATION OF WHETHER OR NOT AN INSULATION FEATURE IS PROVIDED ON THE JAW. SELECT REPLY CODE 10AB22 ANSWD /D/ 07SWITCH,SCALE-SELECTOR SCALE-SELECTOR SWITCH AN INDICATION OFWHETHER OR NOT AN INTEGRAL SWITCH FOR SELECTING A SCALE IS INCLUDED. SELECT REPLY CODE 10AA49 ANSXD 19UNIT,MEASUREMENT MEASUREMENT UNIT AN INDICATION OF THE UNIT OF MEASURE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK09 ANSYJ T10RANGE,RESPONSE,FREQUENCY FREQUENCY RESPONSE RANGE THE MINIMUM AND MAXIMUM FREQUENCIES TO WHICH THE ITEM WILL RESPOND WITHOUT EXCEEDING ITS ACCURACY RATING. 1D AND 1F MODE REPLY11AC32 ANSZF T10RANGE,MEASUREMENT,SCALE SCALE MEASUREMENT RANGE THE MINIMUM AND MAXIMUM NUMERIC VALUES REPRESENTING THE MEASUREMENT COVERAGE OF A SCALE. 1F MODE REPLY 0 ANTAA /D/ 12QUANTITY PER RANGE,STEP STEP QUANTITY PER RANGE THE NUMBER OF STEPS WITHIN A SPECIFIC RANGE. 1A MODE REPLY 0 ANTBD /D/ 05DIRECTION,MARKING,SCALE SCALE MARKING DIRECTION THE ORDER OF THE SCALE MARKINGS ON THE ITEM. SELECT REPLY CODE 10AB50 ANTCD /D/ 07ADJUSTER,ZERO ZERO ADJUSTER AN INDICATION OF WHETHER OR NOT AN ADJUSTER TO RETURN THE ITEM TO ZERO IS PROVIDED. SELECT REPLY CODE 10AB22 ANTDF T10ACCURACY RATING IN PERCENT,OVERALL,SCALE SCALE OVERALL ACCURACY RATING IN PERCENT THE MINIMUM AND MAXIMUM DEVIATION FROM THE EXACT READING AT FULL SCALE DEFLECTION. 1F MODE REPLY 0 ANTFJ /D/T10ACCURACY RATING PER RANGE IN PERCENT,SCALE SCALE ACCURACY RATING PER RANGE IN PERCENT THE MINIMUM AND MAXIMUM DEVIATION FROM THE EXACT READING OF EACH RANGE AT FULL SCALE DEFLECTION. 1D AND 1F MODE REPLY13AK10 ANTGJ 10SENSITIVITY RATING SENSITIVITY RATING THE RATED SENSITIVITY OF THE ITEM. 1D AND 1B MODE REPLY13AK11 ANTHD 18TYPE,METER METER TYPE AN INDICATION OF THE TYPE OF METER. SELECT REPLY CODE 10AK13 ANTJA 12QUANTITY,METER METER QUANTITY THE NUMBER OF METERS PROVIDED. 1A MODE REPLY 0 ANTKD 18TYPE,ABRASIVE ABRASIVE TYPE INDICATES THE TYPE OF ABRASIVE PROVIDED. SELECT REPLY CODE 10AF67 ANTLD /D/ 07ADDITIVE,DETERGENT DETERGENT ADDITIVE AN INDICATION OF WHETHER OR NOT A DETERGENT ADDITIVE IS INCLUDED. SELECT REPLY CODE 10AA49 ANTMD /D/ 07ADDITIVE,BLEACH BLEACH ADDITIVE AN INDICATION OF WHETHER OR NOT A BLEACH ADDITIVE IS INCLUDED. SELECT REPLY CODE 10AA49 ANTNG 19USE,SPECIFIC SPECIFIC USE THE REQUIRED PURPOSE OR APPLICATION FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 ANTPL 16STYLE,BORE BORE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BORE. 1L MODE REPLY 0 ANTQD 18TYPE,PLUG PLUG TYPE INDICATES THE TYPE OF PLUG PROVIDED. SELECT REPLY CODE 10AK12 ANTRD /D/ 09MATERIAL,PLUG PLUG MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PLUG IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ANTSJ 04RADIUS,GROOVE,RADIAL RADIAL GROOVE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 ANTTJ 04DISTANCE FROM END TO GROOVE CENTER DISTANCE FROM END TO GROOVE CENTER THE DISTANCE FROM THE CENTER OF THE GROOVE TO THE END OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ANTWJ 04DISTANCE FROM END TO SLOT CENTER DISTANCE FROM END TO SLOT CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 ANTXJ 04DISTANCE FROM END TO KEYWAY CENTER DISTANCE FROM END TO KEYWAY CENTER THE DISTANCE FROM THE END OF THE ITEM TO THE CENTER OF THE KEYWAY. 2D AND 1B MODE REPLY21AA051AC20 ANTYJ 04DISTANCE FROM END TO SLOT DISTANCE FROM END TO SLOT NONE. 2D AND 1B MODE REPLY21AA051AC20 ANTZJ 04DISTANCE BETWEEN GROOVE CENTERS DISTANCE BETWEEN GROOVE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 ANWAD /D/ 19FORM,ROLL ROLL FORM AN INDICATION OF THE FORM OF THE ROLL. SELECT REPLY CODE 10AK16 ANWBJ 04DEPTH,BORE BORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ANWCJ 04RADIUS,BORE BORE RADIUS A MEASUREMENT OF THE DISTANCE FROM THE BORE CENTER TO THE INSIDE SURFACE. 2D AND 1B MODE REPLY21AA051AC20 ANWDJ 10VOLTAGE RATING IN VOLTS,OPERATING,AC AC OPERATING VOLTAGE RATING IN VOLTS THE ALTERNATING CURRENT VALUES OF ROOT MEAN SQUARE POTENTIAL WHICH MUST BE APPLIED TO THE ITEM FOR OPERATION,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 ANWED /D/ 09MATERIAL,CASE,CARRYING CARRYING CASE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CARRYING CASE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ANWFD 19ACCOMMODATION,MOUNTING,TEST ITEM TEST ITEM MOUNTING ACCOMMODATION INDICATES THE MOUNTING ACCOMMODATION/S/ OF THE TEST ITEM. SELECT REPLY CODE 10AK14 ANWGD 19MEDIUM FOR WHICH DESIGNED,RECORDING RECORDING MEDIUM FOR WHICH DESIGNED THE RECORDING MEDIUM FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK15 ANWHD /D/ 07INDICATOR,TIME,RECORDING RECORDING TIME INDICATOR AN INDICATION OF WHETHER OR NOT A RECORDING TIME INDICATOR IS INCLUDED. SELECT REPLY CODE 10AA49 ANWJJ 04DIAMETER,MAXIMUM,ACCOMMODATED REEL ACCOMMODATED REEL MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED REEL FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ANWKJ 04DIAMETER,MAXIMUM,ACCOMMODATED SPOOL ACCOMMODATED SPOOL MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED SPOOL FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ANWLA 12QUANTITY,CHANNEL,INPUT INPUT CHANNEL QUANTITY THE NUMBER OF INPUT CHANNEL(S) INCORPORATED IN THE ITEM. 1A MODE REPLY 0 ANWMD 07REPLACEABILITY,STYLUS STYLUS REPLACEABILITY AN INDICATION OF WHETHER OR NOT THE STYLUS IS REPLACEABLE. SELECT REPLY CODE 10AG84 ANWNB 10OUTPUT RATING IN WATTS,AMPLIFIER AMPLIFIER OUTPUT RATING IN WATTS THE RATED POWER THAT AN AMPLIFIER CAN SAFELY PROVIDE,MEASURED IN WATTS. 1B MODE REPLY 0 ANWPJ 10IMPEDANCE RATING IN OHMS,OUTPUT OUTPUT IMPEDANCE RATING IN OHMS THE TOTAL OPPOSITION /RESISTIVE AND REACTIVE/ WHICH THE ITEM OFFERS TO THE OUTPUT FLOW OF ALTERNATING CURRENT,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 ANWQD /D/ 07CHANGER,DISK,AUTOMATIC AUTOMATIC DISK CHANGER AN INDICATION OF WHETHER OR NOT AN AUTOMATIC DISK CHANGER IS INCLUDED. SELECT REPLY CODE 10AA49 ANWRA 12QUANTITY ACCOMMODATED,DISK,MAXIMUM MAXIMUM DISK QUANTITY ACCOMMODATED THE MAXIMUM NUMBER OF DISKS THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 ANWSJ 04SIZE ACCOMMODATED,DISK,MAXIMUM MAXIMUM DISK SIZE ACCOMMODATED DESIGNATES THE MAXIMUM SIZE OF THE DISK THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 ANWTJ 04DIAMETER ACCOMMODATED,HOLE,RECORD RECORD HOLE DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR A RECORD HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ANWUA 12QUANTITY,CHANNEL,OUTPUT OUTPUT CHANNEL QUANTITY THE NUMBER OF OUTPUT CHANNEL(S) INCORPORATED IN THE ITEM. 1A MODE REPLY 0 ANWWJ /D/ 04WIDTH,GROUP,CUT CUT GROUP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF EACH INDIVIDUAL CUT GROUP IN THE ITEM,IN DISTINCTION FROM THICKNESS. 3D AND 1B MODE REPLY31AA051AC202AK17 ANWXJ 04ANGLE IN DEG AND LOCATION,APEX APEX ANGLE IN DEG AND LOCATION A MEASUREMENT OF THE APEX ANGLE,EXPRESSED IN DEGREES,AND ITS LOCATION. 2D AND 1B MODE REPLY21AC203AJ91 ANWYJ /D/A12QUANTITY,GROUP,MULTI-CUT MULTI-CUT GROUP QUANTITY THE NUMBER OF INDIVIDUAL GROUPS INTO WHICH THE ITEM IS CUT. 1D AND 1A MODE REPLY12AK17 ANWZJ 04DIAMETER,INSIDE,CORE CORE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CORE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ANXAD 02DESIGN,PATTERN PATTERN DESIGN THE DESIGN OF THE PATTERN. SELECT REPLY CODE 10AK18 ANXBD 11METHOD,ERASING ERASING METHOD THE MEANS EMPLOYED BY THE ITEM TO ERASE. SELECT REPLY CODE 10AK19 ANXCA 12QUANTITY ACCOMMODATED,REEL REEL QUANTITY ACCOMMODATED THE NUMBER OF REELS THAT CAN BE ACCOMMODATED BY THE ITEM. 1A MODE REPLY 0 ANXDA 12QUANTITY ACCOMMODATED,MAGAZINE MAGAZINE QUANTITY ACCOMMODATED THE NUMBER OF MAGAZINES THAT CAN BE ACCOMMODATED BY THE ITEM. 1A MODE REPLY 0 ANXEJ 04WIDTH,TRACK,ERASE ERASE TRACK WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ERASE TRACK,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ANXFD 18TYPE,MAGNET MAGNET TYPE INDICATES THE TYPE OF MAGNET INCORPORATED IN THE ITEM. SELECT REPLY CODE 10AK20 ANXGJ 10CURRENT RATING,ERASE ERASE CURRENT RATING THE AMOUNT OF ERASE CURRENT FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AC301AC20 ANXHJ 10VOLTAGE IN VOLTS,ERASE ERASE VOLTAGE IN VOLTS THE ERASE VOLTAGE FOR WHICH THE ITEM IS DESIGNED,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 ANXJD /D/ 07FEATURE,SECTIONALIZED SECTIONALIZED FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE FOR SECTIONING THE ITEM IS INCLUDED. SELECT REPLY CODE 10AA49 ANXKD 18TYPE,CARTRIDGE CARTRIDGE TYPE INDICATES THE TYPE OF CARTRIDGE. SELECT REPLY CODE 10AE76 ANXLD /D/ 07STYLUS STYLUS AN INDICATION OF WHETHER OR NOT A STYLUS IS INCLUDED. SELECT REPLY CODE 10AA49 ANXMA 12QUANTITY,TIP TIP QUANTITY THE NUMBER OF TIPS PROVIDED WITH THE ITEM. 1A MODE REPLY 0 ANXND 08LOCATION,SERVICING SERVICING LOCATION INDICATES THE SERVICING LOCATION. SELECT REPLY CODE 10AJ91 ANXPD /D/ 09MATERIAL,TIP,STYLUS STYLUS TIP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE STYLUS TIP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ANXQJ 04RADIUS,TIP,STYLUS STYLUS TIP RADIUS THE RADIUS OF THE STYLUS TIP. 2D AND 1B MODE REPLY21AA051AC20 ANXRB 04ANGLE IN DEG,TIP TIP ANGLE IN DEG THE ANGLE OF THE TIP BEARING SURFACE IN RELATION TO THE LONGITUDINAL AXIS OF THE ITEM,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ANXSD /D/ 07SYSTEM,VENTILATION,POWERED POWERED VENTILATION SYSTEM AN INDICATION OF WHETHER OR NOT A POWERED VENTILATION SYSTEM IS INCLUDED. SELECT REPLY CODE 10AA49 ANXTA 12QUANTITY,TRACK,TAPE TAPE TRACK QUANTITY THE NUMBER OF TAPE TRACK(S) ON THE ITEM. 1A MODE REPLY 0 ANXWB /D/ 10IMPEDANCE RATING IN OHMS IMPEDANCE RATING IN OHMS THE TOTAL OPPOSITION /RESISTIVE AND REACTIVE/ WHICH THE ITEM OFFERS TO THE FLOW OF ALTERNATING CURRENT,EXPRESSED IN OHMS. 1B MODE REPLY 0 ANXXD /D/ 07CARTRIDGE CARTRIDGE AN INDICATION OF WHETHER OR NOT A CARTRIDGE IS INCLUDED. SELECT REPLY CODE 10AA49 ANXYD /D/ 07FEATURE,ILLUMINATED ILLUMINATED FEATURE AN INDICATION OF WHETHER OR NOT AN ILLUMINATED FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 ANXZD 08LOCATION,ILLUMINATED ILLUMINATED LOCATION INDICATES THE ILLUMINATED LOCATION. SELECT REPLY CODE 10AJ91 ANYAD 18TYPE,LINE,COMMUNICATION COMMUNICATION LINE TYPE INDICATES THE TYPE OF LINE USED TO TRANSMIT INFORMATION FROM ONE POINT TO ANOTHER. SELECT REPLY CODE 10AK21 ANYBA 12QUANTITY,LINE,COMMUNICATION COMMUNICATION LINE QUANTITY THE NUMBER OF COMMUNICATION LINE(S). 1A MODE REPLY 0 ANYCB 10VOLTAGE RATING,SYSTEM SYSTEM VOLTAGE RATING THE ELECTRICAL VOLTAGE OF THE SYSTEM FOR WHICH THE ITEM IS DESIGNED. 1B MODE REPLY 0 ANYDD 19POLARITY,GROUND,SYSTEM SYSTEM GROUND POLARITY INDICATES THE TYPE OF GROUND THE ELECTRICAL SYSTEM UTILIZES. SELECT REPLY CODE 10AK22 ANYED 18TYPE,UNIT,VOLTAGE REGULATOR VOLTAGE REGULATOR UNIT TYPE INDICATES THE TYPE OF DEVICE USED TO MAINTAIN A CONSTANT VOLTAGE. SELECT REPLY CODE 10AK23 ANYFA 12QUANTITY ACCOMMODATED,CIRCUITS,RADAR INDICATOR RADAR INDICATOR CIRCUITS QUANTITY ACCOMMODATED THE NUMBER OF RADAR INDICATOR CIRCUITS THE ITEM CAN ACCOMMODATE. 1A MODE REPLY 0 ANYGA 12QUANTITY ACCOMMODATED,CIRCUITS,RADAR SET RADAR SET CIRCUITS QUANTITY ACCOMMODATED THE NUMBER OF RADAR SET CIRCUITS THE ITEM CAN ACCOMMODATE. 1A MODE REPLY 0 ANYHA 12QUANTITY,UNIT,VOLTAGE REGULATOR VOLTAGE REGULATOR UNIT QUANTITY THE NUMBER OF INDIVIDUAL VOLTAGE REGULATOR UNITS CONTAINED IN THE ITEM. 1A MODE REPLY 0 ANYJD 18TYPE,UNIT,CURRENT REGULATOR CURRENT REGULATOR UNIT TYPE INDICATES THE TYPE OF DEVICE USED TO LIMIT THE CURRENT OUTPUT TO THE MAXIMUM SAFE VALUE. SELECT REPLY CODE 10AK23 ANYKA 12QUANTITY,UNIT,CURRENT REGULATOR CURRENT REGULATOR UNIT QUANTITY THE NUMBER OF INDIVIDUAL CURRENT REGULATOR UNITS CONTAINED IN THE ITEM. 1A MODE REPLY 0 ANYLD /D/ 07FEATURE,POROUS POROUS FEATURE AN INDICATION OF WHETHER OR NOT A POROUS FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ANYMJ /D/ 04DIAMETER,OUTSIDE,ROLL ROLL OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ROLL,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ANYNJ 10PERCENTAGE,ELONGATION ELONGATION PERCENTAGE THE PERCENTAGE THE ITEM WILL STRETCH. 1D AND 1B MODE REPLY11AC20 ANYPJ 10CURRENT RATING IN AMPS,OUTPUT OUTPUT CURRENT RATING IN AMPS THE CURRENT THE ITEM WILL PERMIT TO PASS,EXPRESSED IN AMPERES. 1D AND 1B MODE REPLY11AC20 ANYQD /D/ 07FEATURE,ILLUMINATED,INTERNALLY INTERNALLY ILLUMINATED FEATURE AN INDICATION OF WHETHER OR NOT AN INTERNAL ILLUMINATION FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 ANYRD 18TYPE,DEVICE,CIRCUIT CONTROL CIRCUIT CONTROL DEVICE TYPE INDICATES THE TYPE OF DEVICE USED TO CLOSE AND OPEN (BREAK) THE CIRCUIT. SELECT REPLY CODE 10AK24 ANYSJ 10VOLTAGE RATING,CUT-IN CUT-IN VOLTAGE RATING THE CUT-IN VOLTAGE/S/ REQUIRED TO CLOSE THE CIRCUIT. 1D AND 1B MODE REPLY11AC20 ANYTA 12QUANTITY PER SECTION,POSITION,CONNECTING CONNECTING POSITION QUANTITY PER SECTION THE NUMBER OF CONNECTING POSITIONS PROVIDED PER SECTION. 1A MODE REPLY 0 ANYWA 12QUANTITY,RECEPTACLE RECEPTACLE QUANTITY THE NUMBER OF RECEPTACLES PROVIDED. 1A MODE REPLY 0 ANYXJ 10VOLTAGE RATING,CUTOUT CUTOUT VOLTAGE RATING THE CUTOUT VOLTAGE/S/ REQUIRED TO OPEN /BREAK/ THE CIRCUIT. 1D AND 1B MODE REPLY11AC20 ANYZJ 10CURRENT RATING IN AMPS,CUTOUT CUTOUT CURRENT RATING IN AMPS THE DISCHARGE /CUTOUT/ CURRENT/S/ REQUIRED TO OPEN /BREAK/ THE CIRCUIT,EXPRESSED IN AMPERES. 1D AND 1B MODE REPLY11AC20 ANZAA 12QUANTITY,UNIT,PATCHING PATCHING UNIT QUANTITY THE NUMBER OF PATCHING UNITS PROVIDED. 1A MODE REPLY 0 ANZBD /D/ 07BREAKER,CIRCUIT,REVERSE CURRENT OVERLOAD REVERSE CURRENT OVERLOAD CIRCUIT BREAKER AN INDICATION OF WHETHER OR NOT A REVERSE CURRENT OVERLOAD CIRCUIT BREAKER IS INCLUDED. SELECT REPLY CODE 10AA49 ANZCD /D/ 07UNIT,RELAY,FIELD FIELD RELAY UNIT AN INDICATION OF WHETHER OR NOT A FIELD RELAY UNIT IS INCLUDED. SELECT REPLY CODE 10AA49 ANZDA 12QUANTITY PER SECTION,PANEL PANEL QUANTITY PER SECTION THE NUMBER OF PANELS PER SECTION. 1A MODE REPLY 0 ANZED 07ENCASEMENT,TERMINAL TERMINAL ENCASEMENT AN INDICATION OF WHETHER OR NOT THE TERMINAL(S) IS ENCASED. SELECT REPLY CODE 10AK25 ANZFA 12QUANTITY,CONNECTION,CONDUIT CONDUIT CONNECTION QUANTITY THE NUMBER OF CONDUIT CONNECTION(S) PROVIDED. 1A MODE REPLY 0 ANZGD 18TYPE,POWER,BATTERY BATTERY POWER TYPE INDICATES THE TYPE OF BATTERY POWER. SELECT REPLY CODE 10AJ93 ANZHD /D/ 07DIAL DIAL AN INDICATION OF WHETHER OR NOT A DIAL IS INCLUDED. SELECT REPLY CODE 10AA49 ANZJA 12QUANTITY,POSITION POSITION QUANTITY THE NUMBER OF POSITIONS PROVIDED. 1A MODE REPLY 0 ANZKG 10SPEED,TRANSMITTING TRANSMITTING SPEED AN INDICATION OF THE SPEED AT WHICH INFORMATION IS TRANSMITTED. FULL TEXT WRITE-IN 0 ANZLD 07FEATURE,RINGING RINGING FEATURE AN INDICATION OF WHETHER OR NOT THE RINGING FEATURE IS SELECTIVE. SELECT REPLY CODE 10AK26 ANZMJ 10FREQUENCY,CARRIER CARRIER FREQUENCY THE VALUE(S) OF THE CARRIER FREQUENCY(IES) WHICH IS MODULATED BY SIGNALS. 2D AND 1B MODE REPLY21AC322AK27 ANZND /D/ 07FACILITY,LOCKING,INCLOSURE INCLOSURE LOCKING FACILITY AN INDICATION OF WHETHER OR NOT THE INCLOSURE IS FURNISHED WITH A LOCKING FACILITY/IES/. SELECT REPLY CODE 10AA55 ANZPD /D/ 07BLANK,DIAL DIAL BLANK AN INDICATION OF WHETHER OR NOT A DIAL BLANK IS INCLUDED. SELECT REPLY CODE 10AA49 ANZQD 18TYPE,ROUTING,CURCUIT CIRCUIT ROUTING TYPE INDICATES THE TYPE OF CIRCUIT ROUTING. SELECT REPLY CODE 10AK28 ANZRA 12QUANTITY,BUTTON,CIRCUIT CONTROL CIRCUIT CONTROL BUTTON QUANTITY THE NUMBER OF BUTTONS ON THE ITEM FOR CIRCUIT CONTROL. 1A MODE REPLY 0 ANZSD /D/ 07SWITCH,PUSH-TO-TALK PUSH-TO-TALK SWITCH AN INDICATION OF WHETHER OR NOT A PUSH-TO-TALK SWITCH IS INCLUDED. MRC DISCONTINUED AND REPLACED WITH MRC CBBL AND REPLY CODE GST, PUSH TO TALK ON 03/28/2024. SELECT REPLY CODE 10AA49 ANZTJ /D/ 10STRENGTH,PEEL,ADHESIVE ADHESIVE PEEL STRENGTH THE PEEL OR STRIPPING STRENGTH OF THE ADHESIVE. 1D AND 1B MODE REPLY12AK29 ANZWD /D/ 11METHOD,HOMING HOMING METHOD THE MEANS OF RESTORING THE ITEM TO A HOMING POSITION. SELECT REPLY CODE 10AK03 ANZXA 12QUANTITY,LEVEL,BANK BANK LEVEL QUANTITY THE NUMBER OF BANK LEVELS PROVIDED. 1A MODE REPLY 0 ANZYA 12QUANTITY PER BANK LEVEL,CONTACT CONTACT QUANTITY PER BANK LEVEL THE NUMBER OF CONTACT/S/ /POINT/ PROVIDED IN EACH BANK LEVEL. 1A MODE REPLY 0 ANZZA 12QUANTITY PER BANK LEVEL,CONTACT,WIPER WIPER CONTACT QUANTITY PER BANK LEVEL THE NUMBER OF WIPER CONTACTS PROVIDED IN EACH BANK LEVEL. 1A MODE REPLY 0 APAAJ 10CURRENT RATING,CONTACT CONTACT CURRENT RATING THE AMOUNT OF CURRENT FOR WHICH THE CONTACT/S/ WAS DESIGNED. 1D AND 1B MODE REPLY11AC30 APABD 18TYPE,CONTACT CONTACT TYPE INDICATES THE TYPE OF CONTACT/S/ USED. SELECT REPLY CODE 10AK30 APACA 12QUANTITY,LEVEL,BRIDGING BRIDGING LEVEL QUANTITY THE NUMBER OF BRIDGING LEVELS PROVIDED. 1A MODE REPLY 0 APADA 12QUANTITY,LEVEL,NONBRIDGING NONBRIDGING LEVEL QUANTITY THE NUMBER OF NONBRIDGING LEVELS PROVIDED. 1A MODE REPLY 0 APAED /D/ 19COMPONENTS,AUXILIARY AUXILIARY COMPONENTS AN INDICATION OF WHETHER OR NOT AUXILIARY COMPONENTS ARE INCLUDED. SELECT REPLY CODE 10AA49 APAFA 12QUANTITY,COIL,MAGNETIC MAGNETIC COIL QUANTITY THE NUMBER OF MAGNETIC COILS PROVIDED. 1A MODE REPLY 0 APAGD 18TYPE,COIL COIL TYPE INDICATES THE TYPE OF COIL USED. SELECT REPLY CODE 10AK03 APAHA 19ACCOMMODATION,LINE,MAXIMUM MAXIMUM LINE ACCOMMODATION THE TOTAL NUMBER OF LINES THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 APAJA 12QUANTITY,LINE LINE QUANTITY THE NUMBER OF LINES PROVIDED. 1A MODE REPLY 0 APAKJ /D/ 04DISTANCE BETWEEN HOLES ALONG WIDTH AND HOLE ALONG LENGTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG WIDTH AND HOLE ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 APALA 12QUANTITY,CORD CORD QUANTITY THE NUMBER OF CORDS PROVIDED. 1A MODE REPLY 0 APAMJ 10CURRENT RATING,OPERATING OPERATING CURRENT RATING THE OPERATING CURRENT FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY21AC301AC20 APAND 18TYPE,LINE LINE TYPE INDICATES THE TYPE OF LINE. SELECT REPLY CODE 10AK31 APAPJ 04DISTANCE BETWEEN HOLES,VERTICAL VERTICAL DISTANCE BETWEEN HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 APAQJ 04LENGTH,SLOT,MOUNTING,LONGEST LONGEST MOUNTING SLOT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 APARJ 04LENGTH,SLOT,MOUNTING,SHORTEST SHORTEST MOUNTING SLOT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 APASJ 04WIDTH,SLOT,OPEN OPEN SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 APATJ /D/ 04DISTANCE BETWEEN SLOTTED HOLES ALONG LENGTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SLOTTED HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 APAWJ /D/ 04DISTANCE BETWEEN SLOTTED HOLES AND PLAIN HOLES ALONG WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SLOTTED HOLES AND PLAIN HOLES ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 APAXJ 04DISTANCE BETWEEN MOUNTING STUDS ALONG WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING STUDS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 APAYA 19CAPACITY,CIRCUIT CIRCUIT CAPACITY THE TOTAL NUMBER OF CIRCUITS THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 APAZJ /D/ 04DISTANCE BETWEEN MOUNTING STUDS ALONG WIDTH AND MOUNTING STUD ALONG LENGTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING STUDS ALONG WIDTH AND MOUNTING STUD ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 APBAJ 04DISTANCE BETWEEN HOLE AND OPEN SLOT ALONG WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN HOLE AND OPEN SLOT ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 APBBJ 04DISTANCE BETWEEN SLOTS ALONG WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SLOTS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 APBCJ 04RADIUS,FACILITY,MOUNTING MOUNTING FACILITY RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 APBDB 04ANGLE BETWEEN PLAIN HOLES IN DEG ANGLE BETWEEN PLAIN HOLES IN DEG NONE. 1B MODE REPLY 0 APBEB 04ANGLE BETWEEN OPEN SLOTS IN DEG ANGLE BETWEEN OPEN SLOTS IN DEG NONE. 1B MODE REPLY 0 APBFB 04ANGLE BETWEEN SLOTTED HOLES IN DEG ANGLE BETWEEN SLOTTED HOLES IN DEG NONE. 1B MODE REPLY 0 APBGB 04ANGLE BETWEEN SLOTTED HOLES AND OPEN SLOTS IN DEG ANGLE BETWEEN SLOTTED HOLES AND OPEN SLOTS IN DEG NONE. 1B MODE REPLY 0 APBHB 04ANGLE BETWEEN SHORTEST SLOTTED HOLES IN DEG ANGLE BETWEEN SHORTEST SLOTTED HOLES IN DEG NONE. 1B MODE REPLY 0 APBJB 04ANGLE BETWEEN LONGEST SLOTTED HOLES IN DEG ANGLE BETWEEN LONGEST SLOTTED HOLES IN DEG NONE. 1B MODE REPLY 0 APBKD 18TYPE,FRONT FRONT TYPE INDICATES THE TYPE OF FRONT PROVIDED. SELECT REPLY CODE 10AK32 APBLA 10COUNT,POINT,TWO-MOTION TWO-MOTION POINT COUNT THE POINT COUNT OF A TWO-MOTION ITEM. 1A MODE REPLY 0 APBMA 12QUANTITY,BANK BANK QUANTITY THE NUMBER OF BANKS PROVIDED. 1A MODE REPLY 0 APBND 05DIRECTION,CONTACT,WIPING WIPING CONTACT DIRECTION AN INDICATION OF THE WIPING CONTACT DIRECTION. SELECT REPLY CODE 10AA99 APBPA 12QUANTITY,CONTACT,WIPING WIPING CONTACT QUANTITY THE NUMBER OF WIPING CONTACTS CONTAINED IN THE ITEM. 1A MODE REPLY 0 APBQD /D/ 07INCLOSURE INCLOSURE AN INDICATION OF WHETHER OR NOT AN INCLOSURE IS INCLUDED. SELECT REPLY CODE 10AA49 APBRJ 10VOLTAGE RATING IN VOLTS,OPERATING,DC DC OPERATING VOLTAGE RATING IN VOLTS THE VALUE/S/ OF DIRECT CURRENT POTENTIAL WHICH MUST BE APPLIED TO THE ITEM FOR OPERATION,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 APBSA 12QUANTITY,CIRCUIT,TWO-WIRE TWO-WIRE CIRCUIT QUANTITY THE NUMBER OF TWO-WIRE CIRCUITS ON THE ITEM. 1A MODE REPLY 0 APBTD 18TYPE,CIRCUIT CIRCUIT TYPE INDICATES THE SPECIFIC TYPE OF CIRCUIT. SELECT REPLY CODE 10AK33 APBWJ T10RANGE,FREQUENCY,CIRCUIT CIRCUIT FREQUENCY RANGE THE FREQUENCY RANGE OF THE CIRCUIT. 1D AND 1F MODE REPLY11AC32 APBXD 19ACTION,SIGNAL,RINGING RINGING SIGNAL ACTION AN INDICATION OF THE RINGING SIGNAL ACTION. SELECT REPLY CODE 10AK34 APBYD 19ACTION,CIRCUIT,PHANTOM PHANTOM CIRCUIT ACTION AN INDICATION OF THE PHANTOM CIRCUIT ACTION. SELECT REPLY CODE 10AK34 APBZD /D/ 07PROVISION,FACILITY,NETWORK,BUILDING-OUT BUILDING-OUT NETWORK FACILITY PROVISION AN INDICATION OF THE BUILDING-OUT NETWORK FACILITY/IES/ PROVISION ON THE ITEM. SELECT REPLY CODE 10AK35 APCAA 12QUANTITY,PANEL PANEL QUANTITY THE NUMBER OF PANELS PROVIDED. 1A MODE REPLY 0 APCBD 07PORTABILITY PORTABILITY AN INDICATION OF WHETHER OR NOT THE ITEM IS PORTABLE. SELECT REPLY CODE 10AK36 APCCJ 10RESISTANCE,ELECTRICAL ELECTRICAL RESISTANCE A MEASUREMENT OF THE OPPOSITION TO THE FLOW OF DIRECT OR ALTERNATING CURRENT. 2D AND 1B MODE REPLY21AA571AC20 APCDA 19ARRANGEMENT,AUXILIARY OFF-NORMAL CONTACT AUXILIARY OFF-NORMAL CONTACT ARRANGEMENT THE BASIC FORM OF THE AUXILIARY OFF-NORMAL CONTACT ARRANGEMENT. 1A MODE REPLY 0 APCEA 19ARRANGEMENT,CONTACT,AUXILIARY INTERRUPTER AUXILIARY INTERRUPTER CONTACT ARRANGEMENT THE BASIC FORM OF THE AUXILIARY INTERRUPTER CONTACT ARRANGEMENT. 1A MODE REPLY 0 APCFA 19NUMBER,VARIETY,CLASS CLASS VARIETY NUMBER THE NUMBER BY WHICH THE CLASS VARIETY IS IDENTIFIED. 1A MODE REPLY 0 APCGD 18TYPE,SHANK SHANK TYPE INDICATES THE PARTICULAR TYPE OF SHANK. SELECT REPLY CODE 10AD07 APCHD /D/ 18TYPE,EYE EYE TYPE INDICATES THE TYPE OF EYE PROVIDED. SELECT REPLY CODE 10AC59 APCJD 05DIRECTION,STEPPING STEPPING DIRECTION AN INDICATION OF THE STEPPING DIRECTION. SELECT REPLY CODE 10AK37 APCKA 12QUANTITY,RELAY,INDIVIDUAL INDIVIDUAL RELAY QUANTITY THE NUMBER OF INDIVIDUAL RELAYS PROVIDED. 1A MODE REPLY 0 APCLD 18TYPE,RELAY RELAY TYPE INDICATES THE TYPE OF RELAY/S/ PROVIDED. SELECT REPLY CODE 10AK38 APCMD 18TYPE,ACTUATION ACTUATION TYPE INDICATES THE TYPE OF ACTUATION PROVIDED. SELECT REPLY CODE 10AC82 APCNA 12QUANTITY,COIL COIL QUANTITY THE NUMBER OF COILS INCLUDED ON THE ITEM. 1A MODE REPLY 0 APCPB 10RESISTANCE IN OHMS RESISTANCE IN OHMS A MEASUREMENT OF THE OPPOSITION TO THE FLOW OF CURRENT,EXPRESSED IN OHMS. 1B MODE REPLY 0 APCQD 18TYPE,STROKE STROKE TYPE INDICATES THE TYPE OF STROKE. SELECT REPLY CODE 10AH83 APCRA 12QUANTITY,SWITCH,INDIVIDUAL INDIVIDUAL SWITCH QUANTITY THE NUMBER OF INDIVIDUAL SWITCHES INCLUDED. 1A MODE REPLY 0 APCSD 07ADJUSTABILITY ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE ITEM IS ADJUSTABLE. SELECT REPLY CODE 10AB00 APCTJ /D/ 19LEGEND A-1 LEGEND A-1 NONE. 2D AND 1B MODE REPLY21AA051AC20 APCWJ /D/ 19LEGEND A-2 LEGEND A-2 NONE. 2D AND 1B MODE REPLY21AA051AC20 APCXJ /D/ 19LEGEND A-3 LEGEND A-3 NONE. 2D AND 1B MODE REPLY21AA051AC20 APCYJ /D/ 19LEGEND HH LEGEND HH NONE. 2D AND 1B MODE REPLY21AA051AC20 APCZJ /D/ 19LEGEND K LEGEND K NONE. 2D AND 1B MODE REPLY21AA051AC20 APDAJ /D/ 19LEGEND L LEGEND L NONE. 2D AND 1B MODE REPLY21AA051AC20 APDBJ /D/ 19LEGEND LL LEGEND LL NONE. 2D AND 1B MODE REPLY21AA051AC20 APDCJ /D/ 19LEGEND N LEGEND N NONE. 2D AND 1B MODE REPLY21AA051AC20 APDDJ /D/ 19LEGEND P LEGEND P NONE. 2D AND 1B MODE REPLY21AA051AC20 APDEG /D/ 19LEGEND T LEGEND T NONE. FULL TEXT WRITE-IN 0 APDFG /D/ 19LEGEND T-1 LEGEND T-1 NONE. FULL TEXT WRITE-IN 0 APDGG /D/ 19LEGEND T-2 LEGEND T-2 NONE. FULL TEXT WRITE-IN 0 APDHJ /D/ 19LEGEND Y LEGEND Y NONE. 2D AND 1B MODE REPLY21AA051AC20 APDJA 19NAME ASSIGNED BY GOVERNMENT AGENCY,ITEM,CONTACT CONTACT ITEM NAME ASSIGNED BY GOVERNMENT AGENCY THE NAME OF THE CONTACT/S/ ASSIGNED BY THE CONTROLLING GOVERNMENT AGENCY. 1A MODE REPLY 0 APDKA 19CONTACT,CONTROLLING,GOVERNMENT AGENCY GOVERNMENT AGENCY CONTROLLING CONTACT THE NAME OF THE GOVERNMENT AGENCY CONTROLLING THE CONTACT/S/. 1A MODE REPLY 0 APDLA 19NUMBER ASSIGNED BY GOVERNMENT AGENCY,IDENTIFYING,CONTACT CONTACT IDENTIFYING NUMBER ASSIGNED BY GOVERNMENT AGENCY AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY CONTROLLING THE CONTACT/S/. 1A MODE REPLY 0 APDMB 10INCREMENTS IN DEG,POSITIONING POSITIONING INCREMENTS IN DEG THE ANGULAR ROTATION THAT THE ITEM MOVES BETWEEN POSITIONS,EXPRESSED IN DEGREES. 1B MODE REPLY 0 APDND 07ADJUSTABILITY,STOP STOP ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE STOP IS ADJUSTABLE. SELECT REPLY CODE 10AB00 APDPF T10RANGE,ADJUSTMENT,STOP STOP ADJUSTMENT RANGE AN INDICATION OF THE ADJUSTMENT RANGE OF THE STOP. 1F MODE REPLY 0 APDQH /D/ 14SHAPE AND LOCATION,CROSS-SECTIONAL,SHAFT SHAFT CROSS-SECTIONAL SHAPE AND LOCATION THE GEOMETRIC CONFIGURATION OF THE SHAFT END,WHEN VIEWED AXIALLY,AND ITS LOCATION. 2D MODE REPLY 22AD073AJ91 APDRG /D/ 04SIZE,NOMINAL NOMINAL SIZE A MEASUREMENT,SUCH AS LENGTH,WIDTH,DIAMETER,AND THE LIKE. FULL TEXT WRITE-IN 0 APDSJ 04DISTANCE FROM SHAFT END TO MOUNTING SURFACE DISTANCE FROM SHAFT END TO MOUNTING SURFACE THE DISTANCE FROM THE END OF THE SHAFT TO THE MOUNTING SURFACE. 1D AND 1B MODE REPLY11AA05 APDTJ /D/ 04DIAMETER,HOLE,CROSS CROSS HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 APDWD /D/ 09MATERIAL,ENVELOPE ENVELOPE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ENVELOPE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 APDXG /D/ 19CLASSIFICATION,MANUFACTURER MANUFACTURER CLASSIFICATION THE CLASSIFICATION ASSIGNED BY THE MANUFACTURER OF THE ITEM. FULL TEXT WRITE-IN 0 APDYA 19ARRANGEMENT,FORM,MAIN CONTACT MAIN CONTACT FORM ARRANGEMENT THE NUMBER AND COMBINATION/S/ OF THE BASIC CONTACT FORMS,IN THE ORDER OF ASSEMBLAGE,WHICH MAKE UP THE SWITCHING STRUCTURE OF THE MAIN CONTACT/S/. 1A MODE REPLY 0 APDZJ A19ARRANGEMENT,CONTACT,MAIN MAIN CONTACT ARRANGEMENT THE DESIGNATION THAT IDENTIFIES THE SCHEMATIC DIAGRAM OF THE ELECTRICAL CONFIGURATION OF THE MAIN CONTACTS INCLUDING THE NUMBER OF POLES OR FORMS. 1D AND 1A MODE REPLY12AG28 APEAD /D/ 19CONDITION,SURFACE SURFACE CONDITION THE CONDITION OF THE ITEM WITH RESPECT TO THE TEXTURE OF THE SURFACE. PLEASE USE MRC SFCD IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AK39 APEBD 18TYPE,CURRENT,MAIN CONTACT MAIN CONTACT CURRENT TYPE INDICATES THE TYPE OF CURRENT USED BY THE MAIN CONTACT/S/. SELECT REPLY CODE 10AB62 APECJ 10CURRENT RATING,CONTACT,MAIN MAIN CONTACT CURRENT RATING THE CURRENT RATING OF THE MAIN CONTACT/S/. 2D AND 1B MODE REPLY21AC301AC20 APEDJ 10WATTAGE RATING,CONTACT,MAIN MAIN CONTACT WATTAGE RATING THE RATED POWER THAT THE MAIN CONTACT/S/ CAN SAFELY CONSUME OR PROVIDE. 2D AND 1B MODE REPLY21AC331AC20 APEFA /D/ 19ARRANGEMENT,FORM,AUXILIARY CONTACT AUXILIARY CONTACT FORM ARRANGEMENT THE NUMBER AND COMBINATION/S/ OF THE BASIC CONTACT FORMS,IN THE ORDER OF ASSEMBLAGE,WHICH MAKE UP THE SWITCHING STRUCTURE OF THE AUXILIARY CONTACT/S/. 1A MODE REPLY 0 APEGJ /D/A19ARRANGEMENT,CONTACT,AUXILIARY AUXILIARY CONTACT ARRANGEMENT THE DESIGNATION THAT IDENTIFIES THE SCHEMATIC DIAGRAM OF THE ELECTRICAL CONFIGURATION OF AN AUXILIARY CONTACT INCLUDING THE NUMBER OF POLES OR FORMS. 1D AND 1A MODE REPLY12AG28 APEHD 18TYPE,CURRENT,AUXILIARY CONTACT AUXILIARY CONTACT CURRENT TYPE INDICATES THE TYPE OF CURRENT USED BY THE AUXILIARY CONTACT/S/. SELECT REPLY CODE 10AB62 APEJJ 04DEPTH,UNDERCUT UNDERCUT DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON AN UNDERCUT,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 APEKJ /D/ 10STROKE,AXIAL AXIAL STROKE THE DISTANCE OF MOVEMENT OF THE AXIAL STROKE. 2D AND 1B MODE REPLY21AA051AC20 APELJ 10CURRENT RATING,CONTACT,AUXILIARY AUXILIARY CONTACT CURRENT RATING THE CURRENT RATING OF THE AUXILIARY CONTACT(S). 2D AND 1B MODE REPLY21AC301AC20 APEMD 18TYPE,LINKAGE LINKAGE TYPE INDICATES THE TYPE OF LINKAGE. SELECT REPLY CODE 10AK41 APEND 18TYPE,SHAFT SHAFT TYPE INDICATES THE TYPE OF SHAFT. SELECT REPLY CODE 10AF58 APEPJ /D/ 10STROKE MAXIMUM RATING,AXIAL AXIAL STROKE MAXIMUM RATING THE SPECIFIC MAXIMUM RATING OF THE AXIAL STROKE. 1D AND 1B MODE REPLY12AK40 APEQD /D/ 07WASHER,FELT FELT WASHER AN INDICATION OF WHETHER OR NOT A FELT WASHER IS INCLUDED. SELECT REPLY CODE 10AA49 APERD /D/ 07FEATURE,UNDERCUT,MACHINED MACHINED UNDERCUT FEATURE AN INDICATION OF WHETHER OR NOT A MACHINED UNDERCUT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 APESJ /D/ 10TORQUE PER INCH,STROKE,ROTARY ROTARY STROKE TORQUE PER INCH THE SPECIFIC AMOUNT OF FORCE PER INCH OF THE ROTARY STROKE. 2D AND 1B MODE REPLY21AA562AK42 APETD 19MOTION,OUTPUT OUTPUT MOTION AN INDICATION OF THE SPECIFIC MECHANICAL MOTION PRODUCED BY THE ITEM. SELECT REPLY CODE 10AF63 APEWD /D/ 18TYPE,TAKEOFF,POWER POWER TAKEOFF TYPE INDICATES THE TYPE OF POWER TAKEOFF. SELECT REPLY CODE 10AK43 APEYB 10STROKE IN DEG,ARC ARC STROKE IN DEG INDICATES THE ARC STROKE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 APEZD /D/ 18TYPE,END,SHAFT EXTENSION SHAFT EXTENSION END TYPE INDICATES THE END TYPE OF THE SHAFT EXTENSION. SELECT REPLY CODE 10AK44 APFAJ A10IMPULSE RATE IMPULSE RATE AN INDICATION OF THE NUMBER OF IMPULSES PER TIME INTERVAL. 1D AND 1A MODE REPLY11AC11 APFBJ 10CURRENT RATING,RELEASE RELEASE CURRENT RATING THE LEVEL OF CURRENT REQUIRED TO RELEASE THE ITEM. 2D AND 1B MODE REPLY21AC301AC20 APFCJ /D/ 04DIAMETER,OUTSIDE,END ENGAGING RATCHET END ENGAGING RATCHET OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE END ENGAGING RATCHET,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 APFDJ /D/ 04DIAMETER,INSIDE,END ENGAGING RATCHET END ENGAGING RATCHET INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE END ENGAGING RATCHET,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 APFEA /D/ 12QUANTITY,HOLE,PLATE COUPLING PLATE COUPLING HOLE QUANTITY THE NUMBER OF HOLES IN THE PLATE COUPLING. 1A MODE REPLY 0 APFFJ /D/ 04DIAMETER,HOLE,PLATE COUPLING PLATE COUPLING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PLATE COUPLING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 APFGB /D/ 04SPACING IN DEG,HOLE,PLATE COUPLING PLATE COUPLING HOLE SPACING IN DEG AN INDICATION OF THE HOLE SPACING OF A PLATE COUPLING,EXPRESSED IN DEGREES. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1B MODE REPLY 0 APFHJ A10FLASHING RATE FLASHING RATE AN INDICATION OF THE NUMBER OF FLASHES PER TIME INTERVAL. 2D AND 1A MODE REPLY21AC111AC20 APFJJ /D/ 04RADIUS,HOLE,PLATE COUPLING PLATE COUPLING HOLE RADIUS THE DISTANCE FROM A CENTER POINT OF THE PLATE COUPLING HOLE TO AN AXIS OF ROTATION. 1D AND 1B MODE REPLY11AA05 APFKJ 10CYCLE,DUTY DUTY CYCLE AN INDICATION OF THE TIME REQUIRED FOR THE ON AND OFF CONDITIONS FOR A COMPLETE OPERATING CYCLE OF AN ITEM. 2D AND 1B MODE REPLY22AN361AK45 APFLG /D/ 18TYPE,END,INTERNAL PLUNGER INTERNAL PLUNGER END TYPE INDICATES THE END TYPE OF THE INTERNAL PLUNGER. FULL TEXT WRITE-IN 0 APFMD 19CONDITION,CIRCUIT,AUTOMATIC,FAILURE FAILURE AUTOMATIC CIRCUIT CONDITION INDICATES THE AUTOMATIC CIRCUIT CONDITION IN CASE OF ITEM FAILURE. SELECT REPLY CODE 10AK45 APFNB 10ACCURACY IN PERCENT ACCURACY IN PERCENT AN INDICATION OF THE ACCURACY OF AN ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 APFPA 12QUANTITY,CIRCUIT,CONTROLLED CONTROLLED CIRCUIT QUANTITY THE NUMBER OF CIRCUITS CONTROLLED BY THE ITEM. 1A MODE REPLY 0 APFQJ 10WATTAGE RATING PER CIRCUIT WATTAGE RATING PER CIRCUIT THE AMOUNT OF POWER A CIRCUIT CAN SAFELY CONSUME OR PROVIDE. 2D AND 1B MODE REPLY21AC331AC20 APFRD 19ARRANGEMENT,CONTACT CONTACT ARRANGEMENT THE DESIGNATION THAT IDENTIFIES THE SCHEMATIC DIAGRAM OF THE CONTACT CONFIGURATION. SELECT REPLY CODE 10AD85 APFSD /D/ 07FACILITY,OPERATION,BATTERY BATTERY OPERATION FACILITY AN INDICATION OF WHETHER OR NOT A FACILITY FOR BATTERY OPERATION IS PROVIDED. SELECT REPLY CODE 10AB22 APFTJ /D/ 10CAPACITY,CURRENT,CONTACT CONTACT CURRENT CAPACITY THE ELECTRICAL CURRENT CAPACITY FOR WHICH THE CONTACT/S/ IS DESIGNED. 2D AND 1B MODE REPLY21AC301AC20 APFWB /D/ 10CAPACITY IN WATTS,WATTAGE,CONTACT CONTACT WATTAGE CAPACITY IN WATTS THE POWER THAT THE CONTACT/S/ CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS. 1B MODE REPLY 0 APFXD 18TYPE,CURRENT,CONTACT CONTACT CURRENT TYPE INDICATES THE TYPE OF CURRENT USED WITH THE CONTACT/S/. SELECT REPLY CODE 10AB62 APFYB 10VOLTAGE RATING IN VOLTS,MAXIMUM MAXIMUM VOLTAGE RATING IN VOLTS THE MAXIMUM VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN VOLTS. 1B MODE REPLY 0 APFZJ /D/ 10CURRENT RATING IN AMPS,COIL COIL CURRENT RATING IN AMPS THE AMOUNT OF CURRENT FOR WHICH THE COIL IS RATED,EXPRESSED IN AMPERES. 1D AND 1B MODE REPLY11AB62 APGAJ /D/ 10VOLTAGE RATING IN VOLTS,MAXIMUM,COIL COIL MAXIMUM VOLTAGE RATING IN VOLTS THE MAXIMUM VOLTAGE RATING AT WHICH THE COIL IS DESIGNED TO OPERATE,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AB62 APGBJ /D/ 10STROKE,ROTARY ROTARY STROKE THE DEGREE OF MOVEMENT IN EITHER DIRECTION OF A MECHANICAL PART REVOLVING ON AN AXIS. 1D AND 1B MODE REPLY12AK50 APGCJ /D/ 04LENGTH FROM CASE,EXTENSION,SHAFT SHAFT EXTENSION LENGTH FROM CASE THE LENGTH OF THE SHAFT EXTENSION FROM THE CASE TO THE END OF THE SHAFT. 2D AND 1B MODE REPLY21AA052AK51 APGDD 19GENDER FOR WHICH DESIGNED GENDER FOR WHICH DESIGNED THE GENDER FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AB60 APGED 19FOOTWEAR FOR WHICH DESIGNED FOOTWEAR FOR WHICH DESIGNED THE SPECIFIC FOOTWEAR FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK46 APGFD 18TYPE,DESIGN DESIGN TYPE INDICATES THE DESIGN TYPE OF THE ITEM. SELECT REPLY CODE 10AK54 APGGG 03DESIGNATOR,SIZE SIZE DESIGNATOR A DESIGNATION INDICATING THE SIZE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. FULL TEXT WRITE-IN 0 APGHD /D/ 03DESIGNATION,RECONSTRUCTION RECONSTRUCTION DESIGNATION A DESIGNATION INDICATING WHETHER OR NOT THE ITEM HAS BEEN REMODELED. SELECT REPLY CODE 10AK48 APGJG /D/ 09MATERIAL AND QUANTITY,NAME,COMPONENT COMPONENT NAME MATERIAL AND QUANTITY THE NAME AND NUMBER OF COMPONENTS,AND THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THEY ARE FABRICATED. FULL TEXT WRITE-IN 0 APGKD /D/ 18TYPE FOR WHICH DESIGNED,HEEL/SOLE HEEL/SOLE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF HEEL/SOLE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK49 APGLA /D/ 12QUANTITY,RECESS,MULTIPLE MOLD MULTIPLE MOLD RECESS QUANTITY THE NUMBER OF MULTIPLE MOLD RECESSES PROVIDED. 1A MODE REPLY 0 APGMJ 10VOLTAGE RATING,CONTACT,AUXILIARY AUXILIARY CONTACT VOLTAGE RATING THE AMOUNT OF VOLTAGE FOR WHICH THE AUXILIARY CONTACT(S) IS RATED. 2D AND 1B MODE REPLY21AB631AC20 APGND 18TYPE,CURRENT,METER MOVEMENT METER MOVEMENT CURRENT TYPE INDICATES THE TYPE OF CURRENT USED IN THE METER MOVEMENT. SELECT REPLY CODE 10AB62 APGPJ 10VOLTAGE IN VOLTS,MOVEMENT,METER METER MOVEMENT VOLTAGE IN VOLTS THE AMOUNT OF VOLTAGE REQUIRED TO OPERATE THE METER MOVEMENT,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 APGQA 12QUANTITY FOR WHICH DESIGNED,LAMP LAMP QUANTITY FOR WHICH DESIGNED THE NUMBER OF LAMPS FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 APGRJ T10RANGE,CURRENT,METER MOVEMENT METER MOVEMENT CURRENT RANGE AN INDICATION OF THE MINIMUM AND MAXIMUM AMOUNT OF CURRENT USED IN THE METER MOVEMENT. 1D AND 1F MODE REPLY11AC30 APGSJ /D/ 10POWER RATING FOR WHICH DESIGNED,LAMP LAMP POWER RATING FOR WHICH DESIGNED THE RATED POWER OF THE LAMP/S/ FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AK521AC20 APGTD 05DIRECTION,RANGE,METER MOVEMENT METER MOVEMENT RANGE DIRECTION AN INDICATION OF THE DIRECTION OF THE METER MOVEMENT READING RANGE. SELECT REPLY CODE 10AB50 APGWJ 10CURRENT RATING AT MAXIMUM RATED VOLTAGE CURRENT RATING AT MAXIMUM RATED VOLTAGE THE AMOUNT OF CURRENT AT MAXIMUM RATED VOLTAGE FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AC302AK53 APGXJ 10CURRENT RATING IN AMPS,MAXIMUM MAXIMUM CURRENT RATING IN AMPS THE MAXIMUM AMOUNT OF CURRENT FOR WHICH THE ITEM IS DESIGNED,EXPRESSED IN AMPERES. 1D AND 1B MODE REPLY12AK53 APGYJ 10VOLTAGE RATING AT MAXIMUM RATED CURRENT VOLTAGE RATING AT MAXIMUM RATED CURRENT THE AMOUNT OF VOLTAGE FOR WHICH THE ITEM IS DESIGNED TO WITHSTAND AT THE MAXIMUM RATED CURRENT. 1D AND 1B MODE REPLY11AB63 APGZD 18TYPE,CURRENT,COIL COIL CURRENT TYPE INDICATES THE TYPE OF CURRENT FOR WHICH THE COIL IS DESIGNED. SELECT REPLY CODE 10AB62 APHAJ 10VOLTAGE IN VOLTS,OPERATING OPERATING VOLTAGE IN VOLTS THE AMOUNT OF OPERATING VOLTAGE,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 APHBJ 10CURRENT IN AMPS,OPERATING OPERATING CURRENT IN AMPS THE AMOUNT OF OPERATING CURRENT,EXPRESSED IN AMPERES. 1D AND 1B MODE REPLY11AC20 APHCD /D/ 07INCLOSURE,MECHANISM,OPERATING OPERATING MECHANISM INCLOSURE AN INDICATION OF WHETHER OR NOT AN OPERATING MECHANISM INCLOSURE IS INCLUDED. SELECT REPLY CODE 10AA49 APHDD /D/ 07SUPPRESSOR,NOISE,ELECTRIC ELECTRIC NOISE SUPPRESSOR AN INDICATION OF WHETHER OR NOT AN ELECTRIC NOISE SUPPRESSOR IS INCLUDED. SELECT REPLY CODE 10AA49 APHED 11METHOD,OPERATION OPERATION METHOD THE MEANS USED TO OPERATE THE ITEM. SELECT REPLY CODE 10AC58 APHFD /D/ 19DEVICE,OPERATING,ELECTROMECHANICAL ELECTROMECHANICAL OPERATING DEVICE THE ELECTROMECHANICAL DEVICE USED TO OPERATE THE ITEM. SELECT REPLY CODE 10AH83 APHGD 11METHOD,LOBING LOBING METHOD THE MEANS USED TO SHIFT THE RADIATION PATTERN OF AN ANTENNA. SELECT REPLY CODE 10AE34 APHHD 11METHOD,OPERATION,SWITCH SWITCH OPERATION METHOD THE MEANS USED TO OPERATE THE SWITCH. SELECT REPLY CODE 10AC58 APHJD 18TYPE,ACTION,SWITCH SWITCH ACTION TYPE INDICATES THE TYPE OF SWITCH ACTION. SELECT REPLY CODE 10AJ27 APHKA 12QUANTITY,POLE,SWITCH SWITCH POLE QUANTITY THE TOTAL NUMBER OF POLES CONTAINED IN A SWITCH. 1A MODE REPLY 0 APHLD /D/ 07POSITION,OFF,SWITCH SWITCH OFF POSITION AN INDICATION OF WHETHER OR NOT AN OFF POSITION IS INCLUDED IN THE SWITCH. SELECT REPLY CODE 10AA49 APHMJ 10IMPEDANCE,CHARACTERISTIC,TRANSMISSION LINE TRANSMISSION LINE CHARACTERISTIC IMPEDANCE THE REACTANCE-RESISTANCE COMPLEX VALUE WHICH MUST BE MATCHED BY THE TRANSMISSION LINE TO ACHIEVE LOWEST STANDING WAVE RATIO. 2D AND 1B MODE REPLY21AA571AC20 APHNG /D/ 19DIMENSIONS IN INCHES,INSIDE,WAVEGUIDE WAVEGUIDE INSIDE DIMENSIONS IN INCHES THE INSIDE DIMENSIONS OF THE WAVEGUIDE,EXPRESSED IN INCHES. FULL TEXT WRITE-IN 0 APHPD /D/ 07FACILITY,OPERATION,MANUAL MANUAL OPERATION FACILITY AN INDICATION OF WHETHER OR NOT A MANUAL OPERATION FACILITY IS PROVIDED. SELECT REPLY CODE 10AB22 APHQA 12QUANTITY,LIGHT LIGHT QUANTITY THE NUMBER OF LIGHTS INCLUDED. 1A MODE REPLY 0 APHRJ /D/ 10VOLTAGE RATING,PRIMARY PRIMARY VOLTAGE RATING THE VALUE(S) OF THE PRIMARY VOLTAGE. 2D AND 1B MODE REPLY21AB631AC20 APHSJ /D/ 10VOLTAGE RATING,SECONDARY SECONDARY VOLTAGE RATING THE VALUE(S) OF THE SECONDARY VOLTAGE. 2D AND 1B MODE REPLY21AB631AC20 APHTD /D/ 07ACTUATOR,LUMINOUS LUMINOUS ACTUATOR AN INDICATION OF WHETHER OR NOT A LUMINOUS ACTUATOR IS INCLUDED. SELECT REPLY CODE 10AA49 APHWJ /D/ 10VOLTAGE IN VOLTS VOLTAGE IN VOLTS THE VALUE/S/ FOR WHICH THE ITEM IS RATED,EXPRESSED IN VOLTS. 2D AND 1B MODE REPLY21AB621AC20 APHXJ /D/ 10CURRENT RATING IN AMPS CURRENT RATING IN AMPS THE AMOUNT OF CURRENT FOR WHICH THE ITEM IS DESIGNED,EXPRESSED IN AMPERES. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1D AND 1B MODE REPLY11AC20 APHYD /D/ 07ENTRANCE ENTRANCE AN INDICATION OF WHETHER OR NOT AN ENTRANCE IS PROVIDED. SELECT REPLY CODE 10AB22 APHZD /D/ 18TYPE,ENTRANCE ENTRANCE TYPE INDICATES THE TYPE OF ENTRANCE ON THE ITEM. SELECT REPLY CODE 10AK60 APJAA /D/ 12QUANTITY,ENTRANCE,UNTHREADED UNTHREADED ENTRANCE QUANTITY THE NUMBER OF UNTHREADED ENTRANCES CONTAINED IN THE ITEM. 1A MODE REPLY 0 APJBA /D/ 12QUANTITY,ENTRANCE,THREADED THREADED ENTRANCE QUANTITY THE NUMBER OF THREADED ENTRANCES CONTAINED IN THE ITEM. 1A MODE REPLY 0 APJCD 13THREAD LOCATION THREAD LOCATION INDICATES THE LOCATION OF THE THREAD ON THE ITEM. SELECT REPLY CODE 10AJ91 APJDD /D/ 01COLOR,BACKGROUND BACKGROUND COLOR THE HUE OR TINT OF THE BACKGROUND. SELECT REPLY CODE 10AD06 APJED /D/ 19SOURCE,SHADE,BACKGROUND BACKGROUND SHADE SOURCE THE NAME OF THE REFERENCE SOURCE OF THE BACKGROUND SHADE IDENTIFICATION DESIGNATOR. SELECT REPLY CODE 10AF94 APJFA /D/ 19IDENTIFICATION,SHADE,BACKGROUND BACKGROUND SHADE IDENTIFICATION A DESIGNATION ASSIGNED TO A PARTICULAR GRADATION OF A COLOR FOR PURPOSE OF READY IDENTIFICATION OF THE BACKGROUND. 1A MODE REPLY 0 APJGD /D/ 01COLOR,STRIPES/CHECKS STRIPES/CHECKS COLOR THE HUE OR TINT OF THE STRIPES OR CHECKS. SELECT REPLY CODE 10AD06 APJHD /D/ 19SOURCE,SHADE,STRIPES/CHECKS STRIPES/CHECKS SHADE SOURCE THE NAME OF THE REFERENCE SOURCE OF THE SHADE IDENTIFICATION DESIGNATOR OF THE STRIPES OR CHECKS. SELECT REPLY CODE 10AF94 APJJA /D/ 19IDENTIFICATION,SHADE,STRIPES/CHECKS STRIPES/CHECKS SHADE IDENTIFICATION A DESIGNATION ASSIGNED TO A PARTICULAR GRADATION OF A COLOR FOR PURPOSE OF READY IDENTIFICATION OF THE STRIPES OR CHECKS. 1A MODE REPLY 0 APJKD /D/ 11METHOD,CLOSING,FLY FLY CLOSING METHOD THE MEANS BY WHICH THE FLY OPENING IS CLOSED. SELECT REPLY CODE 10AF69 APJLD /D/ 07PIECE,FLY,PROTECTIVE PROTECTIVE FLY PIECE AN INDICATION OF WHETHER OR NOT A PROTECTIVE FLY PIECE IS INCLUDED. SELECT REPLY CODE 10AA49 APJMD /D/ 11METHOD,CLOSING,LEG BOTTOM LEG BOTTOM CLOSING METHOD THE MEANS BY WHICH THE LEG BOTTOM OPENING IS CLOSED. SELECT REPLY CODE 10AF69 APJND /D/ 08LOCATION,REINFORCEMENT REINFORCEMENT LOCATION INDICATES THE LOCATION OF THE ITEM WHICH IS REINFORCED. SELECT REPLY CODE 10AJ91 APJPD 08LOCATION,POCKET POCKET LOCATION INDICATES THE LOCATION OF THE POCKET IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 APJQD /D/ 07FLAPS,POCKET POCKET FLAPS AN INDICATION OF WHETHER OR NOT POCKET FLAPS ARE PROVIDED. SELECT REPLY CODE 10AB22 APJRD /D/ 11METHOD,CLOSURE,POCKET POCKET CLOSURE METHOD THE MEANS BY WHICH THE POCKET OPENING IS CLOSED. SELECT REPLY CODE 10AF69 APJSD /D/ 07FRONT,BROADFALL BROADFALL FRONT AN INDICATION OF WHETHER OR NOT A BROADFALL FRONT IS INCLUDED. SELECT REPLY CODE 10AA49 APJTD 07TERMINATION,BOTTOM BOTTOM TERMINATION AN INDICATION OF WHETHER OR NOT THE BOTTOM TERMINATION IS FINISHED. SELECT REPLY CODE 10AA73 APJWD /D/ 07CUFF CUFF AN INDICATION OF WHETHER OR NOT CUFFS ARE PROVIDED. SELECT REPLY CODE 10AB22 APJXB 10RESISTANCE IN OHMS,DC,MAXIMUM MAXIMUM DC RESISTANCE IN OHMS THE MAXIMUM OPPOSITION TO THE FLOW OF DIRECT CURRENT,EXPRESSED IN OHMS. 1B MODE REPLY 0 APJYA 12QUANTITY,WINDING,NONINDUCTIVE NONINDUCTIVE WINDING QUANTITY THE NUMBER OF NONINDUCTIVE WINDINGS. 1A MODE REPLY 0 APJZD /D/ 18TYPE,FOOTWEAR FOOTWEAR TYPE INDICATES THE TYPE OF FOOTWEAR. SELECT REPLY CODE 10AK54 APKAD /D/ 09MATERIAL,FOOTWEAR,UPPER UPPER FOOTWEAR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE UPPER PART OF THE FOOTWEAR IS FABRICATED. SELECT REPLY CODE 10AD09 APKBD /D/ 01COLOR,FOOTWEAR,UPPER UPPER FOOTWEAR COLOR THE HUE OR TINT OF THE UPPER FOOTWEAR. SELECT REPLY CODE 10AD06 APKCD /D/ 18TYPE,TOE TOE TYPE INDICATES THE TYPE OF TOE. SELECT REPLY CODE 10AK55 APKDD /D/ 09MATERIAL,SOLE SOLE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SOLE IS FABRICATED. SELECT REPLY CODE 10AD09 APKED /D/ 01COLOR,SOLE SOLE COLOR THE HUE OR TINT OF THE SOLE. SELECT REPLY CODE 10AD06 APKFD /D/ 18TYPE,PROJECTION,SOLE SOLE PROJECTION TYPE INDICATES THE TYPE OF PROJECTION ON THE SOLE. SELECT REPLY CODE 10AK56 APKGD /D/ 18TYPE,DESIGN,SOLE SOLE DESIGN TYPE INDICATES THE DESIGN TYPE CHARACTERISTIC OF THE SOLE. SELECT REPLY CODE 10AK57 APKHD /D/ 09MATERIAL,HEEL HEEL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HEEL IS FABRICATED. SELECT REPLY CODE 10AD09 APKJD /D/ 01COLOR,HEEL HEEL COLOR THE HUE OR TINT OF THE HEEL. SELECT REPLY CODE 10AD06 APKKJ 04HEIGHT,HEEL HEEL HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE HEEL,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 APKLD /D/ 18TYPE,PROJECTION,HEEL HEEL PROJECTION TYPE INDICATES THE TYPE OF PROJECTION ON THE HEEL. SELECT REPLY CODE 10AK56 APKMD /D/ 18TYPE,DESIGN,HEEL HEEL DESIGN TYPE INDICATES THE DESIGN TYPE CHARACTERISTIC OF THE HEEL. SELECT REPLY CODE 10AK57 APKND /D/ 19PROTECTION,ENVIRONMENTAL,SOLE SOLE ENVIRONMENTAL PROTECTION THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT THE SOLE IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY. SELECT REPLY CODE 10AA65 APKPD /D/ 19PROTECTION,ENVIRONMENTAL,HEEL HEEL ENVIRONMENTAL PROTECTION THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT THE HEEL IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY. SELECT REPLY CODE 10AA65 APKQD /D/ 18TYPE,SHOE,BOWLING BOWLING SHOE TYPE INDICATES THE TYPE OF BOWLING SHOE. SELECT REPLY CODE 10AA38 APKRD /D/ 07ARCH,FLEXIBLE,MOLDED MOLDED FLEXIBLE ARCH AN INDICATION OF WHETHER OR NOT A MOLDED FLEXIBLE ARCH IS INCLUDED. SELECT REPLY CODE 10AA49 APKSD 18TYPE,RINGER RINGER TYPE INDICATES THE SPECIFIC TYPE OF RINGER. SELECT REPLY CODE 10AK67 APKTD /D/ 07FEATURE,WASH AND WEAR WASH AND WEAR FEATURE AN INDICATION OF WHETHER OR NOT A WASH AND WEAR FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 APKWD /D/ 07FASTENER,SNAP,WAIST TO CUFF WAIST TO CUFF SNAP FASTENER AN INDICATION OF WHETHER OR NOT SNAP FASTENERS FROM WAIST TO CUFF ARE INCLUDED. SELECT REPLY CODE 10AA49 APKXD /D/ 07TAPES,TIE,LEGS-CROTCH-CARGO POCKET LEGS-CROTCH-CARGO POCKET TIE TAPES AN INDICATION OF WHETHER OR NOT TIE TAPES AROUND LEGS,THROUGH CROTCH,AND OVER CARGO POCKETS ARE INCLUDED. SELECT REPLY CODE 10AA49 APKYD /D/ 07REMOVABILITY,LINER LINER REMOVABILITY AN INDICATION OF WHETHER OR NOT THE LINER IS REMOVABLE. SELECT REPLY CODE 10AC29 APKZD /D/ 19NAME,CLOTH,LINING LINING CLOTH NAME THE NOUN,WITH OR WITHOUT MODIFIERS,BY WHICH THE CLOTH USED TO COVER THE INNER SURFACE OF AN ITEM IS KNOWN OR DESIGNATED. SELECT REPLY CODE 10AF82 APLAJ /D/ 10WEIGHT,CLOTH,LINING LINING CLOTH WEIGHT A DESIGNATION EXPRESSED IN UNITS OF WEIGHT PER SQUARE OR LINEAR YARD OF A SPECIFIED (BASIC) WIDTH OF THE CLOTH LINING. 2D AND 1B MODE REPLY22AG691AC20 APLBD /D/ 19PROTECTION,ENVIRONMENTAL,LINING CLOTH LINING CLOTH ENVIRONMENTAL PROTECTION THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT THE LINING CLOTH IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY. SELECT REPLY CODE 10AA65 APLCJ /D/ 04SIZE,WAIST WAIST SIZE THE WAIST SIZE DESIGNATION AS DETERMINED BY THE MANUFACTURER. 2D AND 1B MODE REPLY21AA051AC20 APLEA /D/ 03DESIGNATION,SIZE,YEAR YEAR SIZE DESIGNATION A MANUFACTURERS DESIGNATION INDICATING YEAR (AGE) SIZE FOR WHICH AN ITEM IS SPECIFICALLY DESIGNED. 1A MODE REPLY 0 APLFB 10FREQUENCY IN HERTZ,OPERATING OPERATING FREQUENCY IN HERTZ THE SPECIFIC FREQUENCY AT WHICH THE ITEM OPERATES,EXPRESSED IN HERTZ. 1B MODE REPLY 0 APLGD 07ADJUSTABILITY,ARMATURE ARMATURE ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE ARMATURE IS ADJUSTABLE. SELECT REPLY CODE 10AB00 APLHJ 04DIAMETER,GONG GONG DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A GONG,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 APLJD 18TYPE,REPEATER REPEATER TYPE INDICATES THE SPECIFIC TYPE OF REPEATER. SELECT REPLY CODE 10AJ83 APLKA 12QUANTITY,CHANNEL,REPEATER REPEATER CHANNEL QUANTITY THE NUMBER OF CHANNELS ON THE REPEATER. 1A MODE REPLY 0 APLLJ /D/T10RANGE IN HERTZ,FREQUENCY,CHANNEL CHANNEL FREQUENCY RANGE IN HERTZ THE FREQUENCY RANGE OF THE CHANNEL/S/ ON THE ITEM,EXPRESSED IN HERTZ. PLEASE USE MRC APQK IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1F MODE REPLY11AC60 APLMA 12QUANTITY,WIRE,CARRIER SYSTEM CARRIER SYSTEM WIRE QUANTITY THE NUMBER OF WIRES ON THE CARRIER SYSTEM. 1A MODE REPLY 0 APLND /D/ 07FACILITY,WIRE,ORDER ORDER WIRE FACILITY AN INDICATION OF WHETHER OR NOT AN ORDER WIRE FACILITY/IES/ IS INCLUDED. SELECT REPLY CODE 10AA49 APLPD /D/ 07FACILITY,MONITORING MONITORING FACILITY AN INDICATION OF WHETHER OR NOT A MONITORING FACILITY/IES/ IS INCLUDED. SELECT REPLY CODE 10AA49 APLQA 19ARRANGEMENT,CONTACT,SWITCH SWITCH CONTACT ARRANGEMENT THE DESIGNATION THAT IDENTIFIES THE SCHEMATIC DIAGRAM OF THE ELECTRICAL CONFIGURATION OF A SWITCH. 1A MODE REPLY 0 APLRA 19ARRANGEMENT,FORM,SWITCH CONTACT SWITCH CONTACT FORM ARRANGEMENT THE NUMBER AND COMBINATION/S/ OF THE BASIC CONTACT FORMS,IN THE ORDER OF ASSEMBLAGE,THAT MAKE UP THE SWITCHING STRUCTURE OF THE SWITCH. 1A MODE REPLY 0 APLSB 10VOLTAGE RATING IN VOLTS,MAXIMUM,CONTACT CONTACT MAXIMUM VOLTAGE RATING IN VOLTS THE MAXIMUM VOLTAGE RATING AT WHICH THE CONTACT IS RATED,EXPRESSED IN VOLTS. 1B MODE REPLY 0 APLTJ 10CURRENT RATING AT MAXIMUM RATED VOLTAGE,CONTACT CONTACT CURRENT RATING AT MAXIMUM RATED VOLTAGE THE AMOUNT OF CURRENT AT MAXIMUM RATED VOLTAGE FOR WHICH THE CONTACT/S/ IS DESIGNED. 2D AND 1B MODE REPLY21AC302AK53 APLWJ 10CURRENT,RATED,CONTACT MAXIMUM CONTACT MAXIMUM RATED CURRENT THE MAXIMUM AMOUNT OF CURRENT THE CONTACT/S/ WILL ACCOMMODATE. 2D AND 1B MODE REPLY21AC302AK53 APLXB 10VOLTAGE RATING AT MAXIMUM RATED CURRENT,CONTACT CONTACT VOLTAGE RATING AT MAXIMUM RATED CURRENT AN INDICATION OF THE AMOUNT OF VOLTAGE FOR WHICH THE CONTACT/S/ IS DESIGNED TO WITHSTAND AT THE MAXIMUM RATED CURRENT. 1B MODE REPLY 0 APLYA 19ARRANGEMENT,CONTACT,CIRCUIT OVERLOAD PROTECTOR CIRCUIT OVERLOAD PROTECTOR CONTACT ARRANGEMENT THE DESIGNATION THAT IDENTIFIES THE SCHEMATIC DIAGRAM OF THE ELECTRICAL CONFIGURATION OF THE CIRCUIT OVERLOAD PROTECTOR. 1A MODE REPLY 0 APLZJ 10VOLTAGE,AC,CONTINUOUS LOAD CONTINUOUS LOAD AC VOLTAGE THE ALTERNATING CURRENT VOLTAGE OF THE CONTINUOUS LOAD. 2D AND 1B MODE REPLY21AB631AC20 APMAJ 10FREQUENCY RATING,LOAD,CONTINUOUS CONTINUOUS LOAD FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY21AC321AC20 APMBJ 10CURRENT RATING,AC,CONTINUOUS LOAD CONTINUOUS LOAD AC CURRENT RATING THE ALTERNATING CURRENT RATING OF THE CONTINUOUS LOAD. 2D AND 1B MODE REPLY21AC301AC20 APMCJ 10VOLTAGE RATING,DC,CONTINUOUS LOAD CONTINUOUS LOAD DC VOLTAGE RATING THE VALUE/S/,OR RANGE OF VALUES,OF DIRECT CURRENT POTENTIAL FOR WHICH THE CONTINUOUS LOAD IS RATED. 2D AND 1B MODE REPLY21AB631AC20 APMDJ 10CURRENT RATING,DC,CONTINUOUS LOAD CONTINUOUS LOAD DC CURRENT RATING THE DIRECT CURRENT RATING OF THE CONTINUOUS LOAD. 2D AND 1B MODE REPLY21AC301AC20 APMEJ 10CAPACITY,INTERRUPTING INTERRUPTING CAPACITY THE INTERRUPTING CAPACITY OF THE ITEM. 2D AND 1B MODE REPLY21AC301AC20 APMFB /D/ 10CURRENT IN PERCENT,TRIPPING,MINIMUM MINIMUM TRIPPING CURRENT IN PERCENT THE MINIMUM CURRENT USED TO TRIP THE ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 APMGB 10TIME IN SECONDS,TRIPPING TRIPPING TIME IN SECONDS THE AMOUNT OF TIME REQUIRED FOR TRIPPING THE ITEM,EXPRESSED IN SECONDS. 1B MODE REPLY 0 APMHB 10PERCENTAGE PER SPECIFIED TRIPPING ACTION TIME,LOAD,CONTINUOUS CONTINUOUS LOAD PERCENTAGE PER SPECIFIED TRIPPING ACTION TIME THE CONTINUOUS LOAD PERCENTAGE FOR THE SPECIFIED TRIPPING TIME OF THE ITEM. 1B MODE REPLY 0 APMJD 18TYPE,TRIP TRIP TYPE INDICATES THE TYPE OF TRIPPING ACTION USED BY THE ITEM. SELECT REPLY CODE 10AK64 APMKD /D/ 17SURFACE TREATMENT,INCLOSURE INCLOSURE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF OF THE INCLOSURE SURFACE. PLEASE USE MRC CTFB IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 APMLJ 10FREQUENCY RATING,MOVEMENT,METER METER MOVEMENT FREQUENCY RATING THE CYCLES PER SECOND /HERTZ/ OF CURRENT OF THE METER MOVEMENT. 2D AND 1B MODE REPLY21AC321AC20 APMMD 01COLOR,MARKING,SCALE,DIAL DIAL SCALE MARKING COLOR THE HUE OR TINT OF THE DIAL SCALE MARKING(S). SELECT REPLY CODE 10AD06 APMND /D/ 18TYPE,ACTIVATION,DIAL LUMINOUS SCALE MARKING DIAL LUMINOUS SCALE MARKING ACTIVATION TYPE AN INDICATION OF WHETHER OR NOT THE LUMINOUS SCALE MARKING/S/ ARE ACTIVATED BY ULTRAVIOLET. SELECT REPLY CODE 10AK58 APMPA 12QUANTITY,REED,RESONANT RESONANT REED QUANTITY THE SPECIFIC NUMBER OF RESONANT REEDS. 1A MODE REPLY 0 APMQJ /D/ 10FREQUENCY,REED,RESONANT RESONANT REED FREQUENCY THE FREQUENCY AT WHICH THE RESONANT REEDS ARE DESIGNED. 2D AND 1B MODE REPLY21AC321AC20 APMRD 18TYPE,MOUNTING,METER METER MOUNTING TYPE INDICATES THE TYPE OF MOUNT UTILIZED TO SUPPORT THE METER. SELECT REPLY CODE 10AA78 APMSF T10TOLERANCE IN PERCENT,FREQUENCY FREQUENCY TOLERANCE IN PERCENT THE PERMISSIBLE VARIATION IN THE FREQUENCY,EXPRESSED IN PERCENT. 1F MODE REPLY 0 APMTD 19CONDITION,CLOSING,CONTACT CONTACT CLOSING CONDITION AN INDICATION OF THE SPECIFIC CONDITION THAT CAUSES THE CONTACTS TO CLOSE. SELECT REPLY CODE 10AK59 APMWJ 10VOLTAGE RATING,MAXIMUM MAXIMUM VOLTAGE RATING THE MAXIMUM VALUE,OR RANGE OF VALUES,OF VOLTAGE FOR WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY11AB63 APMXJ 10WATTAGE RATING AT MAXIMUM RATED CURRENT WATTAGE RATING AT MAXIMUM RATED CURRENT THE WATTAGE RATING OF THE ITEM AT THE MAXIMUM CURRENT RATING. 1D AND 1B MODE REPLY11AC33 APMYA /D/ 12QUANTITY,WINDING,INDUCTIVE INDUCTIVE WINDING QUANTITY THE NUMBER OF INDUCTIVE WINDINGS INCLUDED. 1A MODE REPLY 0 APNAJ 10RESISTANCE RATING,DC,WINDING WINDING DC RESISTANCE RATING THE MEASURED OPPOSITION TO THE FLOW OF DIRECT CURRENT OFFERED BY THE ITEM WINDING. 2D AND 1B MODE REPLY21AA571AC20 APNBJ 10FREQUENCY RATING,AC AC FREQUENCY RATING THE NUMBER OF COMPLETE ALTERNATING CURRENT CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY21AC321AC20 APNCD /D/ 07FEATURE,WOUND,DIFFERENTIALLY DIFFERENTIALLY WOUND FEATURE AN INDICATION OF WHETHER OR NOT A DIFFERENTIALLY WOUND FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 APNDJ /D/ 10CURRENT RATING,OPERATING,MINIMUM DIFFERENTIAL MINIMUM DIFFERENTIAL OPERATING CURRENT RATING THE MINIMUM OPERATING CURRENT OF THE ITEM DIFFERENTIAL. 1D AND 1B MODE REPLY11AC30 APNEB 10VOLTAGE IN VOLTS,OPERATING OPERATING VOLTAGE IN VOLTS AN INDICATION OF THE AMOUNT OF OPERATING VOLTAGE,EXPRESSED IN VOLTS. 1B MODE REPLY 0 APNFD /D/ 07FEATURE,LATCHING LATCHING FEATURE AN INDICATION OF WHETHER OR NOT A LATCHING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 APNGA 12QUANTITY,TERMINAL,CONTACT CONTACT TERMINAL QUANTITY THE SPECIFIC NUMBER OF CONTACT TERMINALS INCLUDED. 1A MODE REPLY 0 APNHA 12QUANTITY,TERMINAL,COIL COIL TERMINAL QUANTITY THE SPECIFIC NUMBER OF COIL TERMINALS INCLUDED. 1A MODE REPLY 0 APNJA 12QUANTITY,TERMINAL,COMMON COMMON TERMINAL QUANTITY THE SPECIFIC NUMBER OF COMMON TERMINALS INCLUDED. 1A MODE REPLY 0 APNKD /D/ 11METHOD,GROUNDING,COIL COIL GROUNDING METHOD THE MEANS BY WHICH THE COIL IS GROUNDED. SELECT REPLY CODE 10AK61 APNLD /D/ 07TIME,ACTUATION ACTUATION TIME AN INDICATION OF WHETHER OR NOT THE ACTUATION TIME IS RATED. SELECT REPLY CODE 10AK62 APNMJ /D/ 10TIME,OPERATING OPERATING TIME AN INDICATION OF THE OPERATING TIME. 2D AND 1B MODE REPLY22AN361AC20 APNNJ /D/ 10TIME,RELEASE RELEASE TIME AN INDICATION OF THE RELEASE TIME. 2D AND 1B MODE REPLY22AN361AC20 APNPD 18TYPE,DUTY DUTY TYPE INDICATES THE TYPE OF DUTY PROVIDED. SELECT REPLY CODE 10AD63 APNQD 11METHOD,QUENCHING,ARC ARC QUENCHING METHOD THE MEANS OF QUENCHING AN ARC. SELECT REPLY CODE 10AK63 APNRD /D/ 07FEATURE,FACILITY,RESET RESET FACILITY FEATURE AN INDICATION OF WHETHER OR NOT THE RESET FACILITIES ARE PROVIDED. SELECT REPLY CODE 10AB22 APNSD 18TYPE,DEVICE,LOCK IN LOCK IN DEVICE TYPE INDICATES THE TYPE OF LOCK IN DEVICE PROVIDED. SELECT REPLY CODE 10AK65 APNTD 11METHOD,RELEASE RELEASE METHOD THE MEANS BY WHICH THE ITEM IS RELEASED. SELECT REPLY CODE 10AK66 APNWA 12QUANTITY,INPUT,ELECTRICAL ELECTRICAL INPUT QUANTITY THE NUMBER OF ELECTRICAL INPUTS ACCOMMODATED. 1A MODE REPLY 0 APNXJ 10VOLTAGE RATING,INPUT INPUT VOLTAGE RATING THE INPUT VALUE/S/,OR RANGE OF VALUES,FOR WHICH THE ITEM IS RATED. 3D AND 1B MODE REPLY31AB621AB631AC20 APNYD /D/ 07NEUTRAL,INPUT INPUT NEUTRAL AN INDICATION OF WHETHER OR NOT AN INPUT NEUTRAL IS PROVIDED. SELECT REPLY CODE 10AB22 APNZA 12QUANTITY,OUTPUT,ELECTRICAL ELECTRICAL OUTPUT QUANTITY THE NUMBER OF ELECTRICAL OUTPUTS PROVIDED. 1A MODE REPLY 0 APPAJ 10VOLTAGE RATING,OUTPUT OUTPUT VOLTAGE RATING THE OUTPUT VALUE/S/,OR RANGE OF VALUES,FOR WHICH THE ITEM IS RATED. 3D AND 1B MODE REPLY31AB621AB631AC20 APPBB 10WATTAGE RATING IN WATTS,OUTPUT OUTPUT WATTAGE RATING IN WATTS THE RATED OUTPUT POWER THAT AN ITEM CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS. 1B MODE REPLY 0 APPCD /D/ 07NEUTRAL,OUTPUT OUTPUT NEUTRAL AN INDICATION OF WHETHER OR NOT AN OUTPUT NEUTRAL IS PROVIDED. SELECT REPLY CODE 10AB22 APPDG 10ABSORBENT RATING,SHOCK SHOCK ABSORBENT RATING THE AMOUNT OF IMPACT OR SHOCK AN ITEM IS RATED TO WITHSTAND. FULL TEXT WRITE-IN 0 APPED /D/ 19CLASSIFICATION,MARKET,POULTRY POULTRY MARKET CLASSIFICATION AN INDICATION OF THE POULTRY MARKET CLASSIFICATION. SELECT REPLY CODE 10AE92 APPFD /D/ 07CABLE CABLE AN INDICATION OF WHETHER OR NOT A CABLE IS INCLUDED. SELECT REPLY CODE 10AA49 APPGD /D/ 07WINDOW,CASE CASE WINDOW AN INDICATION OF WHETHER OR NOT A WINDOW IS INCLUDED IN THE CASE. SELECT REPLY CODE 10AA49 APPHD 08LOCATION,WINDOW WINDOW LOCATION INDICATES THE LOCATION OF THE WINDOW. SELECT REPLY CODE 10AJ91 APPJJ T10RANGE PER HOUR,RADIATION RADIATION RANGE PER HOUR THE MINIMUM AND MAXIMUM AMOUNT OF RADIATION DETECTED PER HOUR. 1D AND 1F MODE REPLY12AJ20 APPKF T10RANGE PER MINUTE,COUNT COUNT RANGE PER MINUTE THE MINIMUM AND MAXIMUM NUMBER OF SINGLE RESPONSES PER MINUTE. 1F MODE REPLY 0 APPLG /D/ 10RANGE,INSTRUMENT INSTRUMENT RANGE THE MINIMUM AND MAXIMUM OF A QUANTITY THAT AN INSTRUMENT WILL INDICATE,RECORD,DETECT,OR CONTROL. FULL TEXT WRITE-IN 0 APPNJ T10ACCURACY IN PERCENT ACCURACY IN PERCENT AN INDICATION OF THE ACCURACY OF AN ITEM,EXPRESSED IN PERCENT. 1D AND 1F MODE REPLY12AK70 APPPJ 10VOLTAGE RATING,SENSITIVITY,INPUT INPUT SENSITIVITY VOLTAGE RATING THE VALUE OF ELECTRICAL POTENTIAL TO WHICH AN ITEM WILL RESPOND. 1D AND 1B MODE REPLY11AB63 APPQJ T10DEPENDENCE RATING,ENERGY ENERGY DEPENDENCE RATING AN INDICATION OF THE ENERGY DEPENDENCE RATING OF THE ITEM. 1D AND 1F MODE REPLY12AJ20 APPSD 18TYPE,TIMER TIMER TYPE INDICATES THE TYPE OF TIMER PROVIDED. SELECT REPLY CODE 10AK74 APPTB 10TIME IN MINUTES,READER,TOTAL TOTAL READER TIME IN MINUTES THE TOTAL PERIOD OF TIME THAT THE READER CAN INDICATE,EXPRESSED IN MINUTES. 1B MODE REPLY 0 APPXJ /D/ 04LENGTH,INSEAM INSEAM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN INSEAM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 APPYB 10FREQUENCY IN HERTZ,INPUT INPUT FREQUENCY IN HERTZ THE CYCLES PER SECOND /HERTZ/ OF INPUT ALTERNATING CURRENT. 1B MODE REPLY 0 APPZB 10FREQUENCY IN HERTZ,RINGING RINGING FREQUENCY IN HERTZ THE CYCLES PER SECOND /HERTZ/ OF THE RINGING ALTERNATING CURRENT. 1B MODE REPLY 0 APQAB 10GAIN IN DECIBELS,OVERALL OVERALL GAIN IN DECIBELS THE AMOUNT OF OVERALL INCREASE IN POWER,EXPRESSED IN DECIBELS. 1B MODE REPLY 0 APQBD 18TYPE,UNIT UNIT TYPE INDICATES THE TYPE OF UNIT. SELECT REPLY CODE 10AK95 APQCD 11METHOD,ACTIVATION ACTIVATION METHOD THE MEANS USED TO ACTIVATE THE ITEM. SELECT REPLY CODE 10AC58 APQDD /D/ 07SWITCH,CLOSER,CIRCUIT CIRCUIT CLOSER SWITCH AN INDICATION OF WHETHER OR NOT A CIRCUIT CLOSER SWITCH IS PROVIDED. SELECT REPLY CODE 10AB22 APQEJ 04DIAMETER,SURFACE,CONTACT CONTACT SURFACE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CONTACT SURFACE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 APQFD /D/ 07SET,CORD CORD SET AN INDICATION OF WHETHER OR NOT A CORD SET IS INCLUDED. SELECT REPLY CODE 10AA49 APQGD 11METHOD,MULTIPLEXING MULTIPLEXING METHOD THE TRANSMITTING METHOD WHICH IDENTIFIES THE FUNCTIONAL DESIGN OF THE ITEM. SELECT REPLY CODE 10AK68 APQHA 12QUANTITY,CHANNEL,TOTAL TOTAL CHANNEL QUANTITY THE TOTAL NUMBER OF CHANNELS ON THE ITEM. 1A MODE REPLY 0 APQJJ A18TYPE AND QUANTITY,CHANNEL CHANNEL TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF CHANNELS PROVIDED. 1D AND 1A MODE REPLY12AK27 APQKF T10RANGE IN HERTZ,FREQUENCY,CHANNEL CHANNEL FREQUENCY RANGE IN HERTZ THE FREQUENCY RANGE OF THE CHANNEL/S/,EXPRESSED IN HERTZ. 1F MODE REPLY 0 APQLJ 10BANDWIDTH,FREQUENCY FREQUENCY BANDWIDTH THE DIFFERENCES BETWEEN LIMITING FREQUENCIES OF A FREQUENCY BAND. 2D AND 1B MODE REPLY21AC321AC20 APQMD 18TYPE,TERMINATION,LINE LINE TERMINATION TYPE INDICATES THE SPECIFIC TYPE OF LINE TERMINATION. SELECT REPLY CODE 10AE79 APQND 18TYPE,CURRENT,LOOP ACTUATION LOOP ACTUATION CURRENT TYPE INDICATES THE TYPE OF CURRENT WHICH ACTUATES THE LOOP. SELECT REPLY CODE 10AB62 APQPD 18TYPE,OPERATION,LOOP LOOP OPERATION TYPE INDICATES THE SPECIFIC TYPE OF LOOP OPERATION REQUIRED. SELECT REPLY CODE 10AK71 APQQJ /D/ 10FREQUENCY RATING,KEYER KEYER FREQUENCY RATING THE RATED FREQUENCY OF THE KEYER. 2D AND 1B MODE REPLY21AC321AC20 APQRD 19DEVICE,SELECTION,LOOP LOOP SELECTION DEVICE THE DEVICE USED IN LOOP SELECTION. SELECT REPLY CODE 10AH83 APQSF /D/T10DEVIATION IN HERTZ,FREQUENCY FREQUENCY DEVIATION IN HERTZ THE AMOUNT BY WHICH THE FREQUENCY VARIES FROM ITS ASSIGNED VALUE,EXPRESSED IN HERTZ. 1F MODE REPLY 0 APQTG /D/ 10SPEED,OPERATIONAL OPERATIONAL SPEED THE NARRATIVE EXPRESSION INDICATING THE SPEED AT WHICH THE ITEM OPERATES. PLEASE USE MRC PESP IN PLACE OF THIS DISCONTINUED MRC. FULL TEXT WRITE-IN 0 APQWJ 10CYCLE,FLASHING FLASHING CYCLE THE SEQUENCE OF THE FLASHING CYCLE. 1D AND 1B MODE REPLY13AK72 APQXD /D/ 07CODING,SPECIAL SPECIAL CODING AN INDICATION OF WHETHER OR NOT SPECIAL CODING IS PROVIDED. SELECT REPLY CODE 10AB22 APQYD 11METHOD,KEYING KEYING METHOD THE MEANS USED FOR KEYING. SELECT REPLY CODE 10AH83 APQZD 19CLASSIFICATION,MARKET,POULTRY POULTRY MARKET CLASSIFICATION AN INDICATION OF THE POULTRY MARKET CLASSIFICATION. SELECT REPLY CODE 10AE92 APRAB 10VOLTAGE IN VOLTS,RINGING RINGING VOLTAGE IN VOLTS THE TOTAL ELECTRICAL RINGING VOLTAGE,EXPRESSED IN VOLTS. 1B MODE REPLY 0 APRBJ 10WATTAGE RATING,CONTACT,AUXILIARY AUXILIARY CONTACT WATTAGE RATING THE RATED POWER THAT THE AUXILIARY CONTACT/S/ CAN SAFELY CONSUME OR PROVIDE. 2D AND 1B MODE REPLY21AC331AC20 APRCJ /D/ 19LEGEND AA LEGEND AA NONE. 2D AND 1B MODE REPLY21AA051AC20 APRDG /D/ 19LEGEND AD LEGEND AD NONE. FULL TEXT WRITE-IN 0 APREJ /D/ 19LEGEND A-4 LEGEND A-4 NONE. 2D AND 1B MODE REPLY21AA051AC20 APRFJ /D/ 19LEGEND A-5 LEGEND A-5 NONE. 2D AND 1B MODE REPLY21AA051AC20 APRGJ /D/ 19LEGEND A-6 LEGEND A-6 NONE. 2D AND 1B MODE REPLY21AA051AC20 APRHL 16STYLE,POINT,ARMED SUTURE NEEDLE ARMED SUTURE NEEDLE POINT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF AN ARMED SUTURE NEEDLE POINT. 1L MODE REPLY 0 APRJJ /D/ 19LEGEND BB LEGEND BB NONE. 2D AND 1B MODE REPLY21AA051AC20 APRKJ /D/ 19LEGEND CC LEGEND CC NONE. 2D AND 1B MODE REPLY21AA051AC20 APRLJ /D/ 19LEGEND C-1 LEGEND C-1 NONE. 2D AND 1B MODE REPLY21AA051AC20 APRML 16STYLE,EYE EYE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE EYE. 1L MODE REPLY 0 APRNJ /D/ 19LEGEND DD LEGEND DD NONE. 2D AND 1B MODE REPLY21AA051AC20 APRPJ /D/ 19LEGEND EE LEGEND EE NONE. 2D AND 1B MODE REPLY21AA051AC20 APRQJ /D/ 19LEGEND FF LEGEND FF NONE. 2D AND 1B MODE REPLY21AA051AC20 APRRJ /D/ 19LEGEND GG LEGEND GG NONE. 2D AND 1B MODE REPLY21AA051AC20 APRSJ /D/ 19LEGEND J LEGEND J NONE. 2D AND 1B MODE REPLY21AA051AC20 APRTJ /D/ 19LEGEND JJ LEGEND JJ NONE. 2D AND 1B MODE REPLY21AA051AC20 APRWJ /D/ 19LEGEND KK LEGEND KK NONE. 2D AND 1B MODE REPLY21AA051AC20 APRXJ /D/ 19LEGEND L-1 LEGEND L-1 NONE. 2D AND 1B MODE REPLY21AA051AC20 APRYJ /D/ 19LEGEND L-2 LEGEND L-2 NONE. 2D AND 1B MODE REPLY21AA051AC20 APRZJ /D/ 19LEGEND M LEGEND M NONE. 2D AND 1B MODE REPLY21AA051AC20 APSAJ /D/ 19LEGEND R LEGEND R NONE. 2D AND 1B MODE REPLY21AA051AC20 APSBJ /D/ 19LEGEND S LEGEND S NONE. 2D AND 1B MODE REPLY21AA051AC20 APSCG /D/ 19LEGEND W LEGEND W NONE. FULL TEXT WRITE-IN 0 APSDG /D/ 19LEGEND X LEGEND X NONE. FULL TEXT WRITE-IN 0 APSEJ 10VOLTAGE,CHARGING CHARGING VOLTAGE THE VOLTAGE THE UNIT IS DESIGNED TO DELIVER. 2D AND 1B MODE REPLY21AB631AC20 APSFD 18TYPE,READER READER TYPE INDICATES THE TYPE OF READER PROVIDED. SELECT REPLY CODE 10AJ12 APSGF T10RANGE,ROENTGENS PER HOUR ROENTGENS PER HOUR RANGE THE RANGE FOR WHICH THE ITEM IS RATED,MEASURED IN ROENTGENS PER HOUR. 1F MODE REPLY 0 APSHD 03DESIGNATION,DESIGN,NEEDLE NEEDLE DESIGN DESIGNATION THE NEEDLE DESIGNATION DERIVED FROM THE NAME OF THE DESIGNER OR USE FOR WHICH THE ITEM IS INTENDED. SELECT REPLY CODE 10AJ50 APSJA 12QUANTITY,SCALE SCALE QUANTITY THE NUMBER OF SCALES ON THE ITEM. 1A MODE REPLY 0 APSKJ T10RANGE,SCALE SCALE RANGE AN INDICATION OF THE SCALE RANGE. 1D AND 1F MODE REPLY12AJ20 APSLD 16STYLE,METER METER STYLE AN INDICATION OF THE METER DESIGN. SELECT REPLY CODE 10AJ17 APSMG 19SENSITIVITY SENSITIVITY AN INDICATION OF THE SENSITIVITY OF THE ITEM. FULL TEXT WRITE-IN 0 APSND 19PANEL FOR WHICH DESIGNED PANEL FOR WHICH DESIGNED AN INDICATION OF THE PANEL FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK76 APSPG /D/ 03DESIGNATOR,RECTIFIER RECTIFIER DESIGNATOR THE DESIGNATION ASSIGNED TO A RECTIFIER FOR PURPOSE OF IDENTIFICATION. FULL TEXT WRITE-IN 0 APSQD 07LUMINOSITY,MARKING,DIAL SCALE DIAL SCALE MARKING LUMINOSITY AN INDICATION OF WHETHER OR NOT THE DIAL SCALE MARKINGS ARE LUMINOUS. SELECT REPLY CODE 10AK77 APSRD 07ACTIVATION,ULTRAVIOLET,LUMINOUS SCALE MARKING LUMINOUS SCALE MARKING ULTRAVIOLET ACTIVATION AN INDICATION OF WHETHER OR NOT THE SCALE MARKINGS LUMINOUS TREATMENT REQUIRES ACTIVATION BY ULTRAVIOLET LIGHT RAYS. SELECT REPLY CODE 10AE40 APSSJ 04DEPTH TO PANEL,METER METER DEPTH TO PANEL A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE METER TO THE PANEL, IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 APSTJ 04DEPTH BEHIND MOUNTING FLANGE,METER METER DEPTH BEHIND MOUNTING FLANGE A MEASUREMENT BETWEEN THE MOUNTING FLANGE AND THE EXTREMITY OF THE METER, INDISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 APSWJ 04DIAMETER BEHIND MOUNTING FLANGE,BODY,METER METER BODY DIAMETER BEHIND MOUNTING FLANGE THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE METER BODY BEHIND THE MOUNTING FLANGE, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 APSXJ 04LENGTH BEHIND MOUNTING FLANGE,BODY,METER METER BODY LENGTH BEHIND MOUNTING FLANGE A MEASUREMENT OF THE LONGEST DIMENSION OF A METER BODY BEHIND THE MOUNTING FLANGE, IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 APSYJ 04WIDTH BEHIND MOUNTING FLANGE,BODY,METER METER BODY WIDTH BEHIND MOUNTING FLANGE A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE METER BODY BEHIND THE MOUNTING FLANGE, IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 APSZD 18TYPE,LIMITING LIMITING TYPE INDICATES THE TYPE OF DEVICE WHICH LIMITS THE AMPLITUDE OF A SIGNAL. SELECT REPLY CODE 10AK80 APTAD 07ADJUSTABILITY,LIMITING LIMITING ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE LIMITING ACTION IS ADJUSTABLE. SELECT REPLY CODE 10AC06 APTBD 18TYPE,RECTIFIER RECTIFIER TYPE INDICATES THE TYPE OF RECTIFIER PROVIDED. SELECT REPLY CODE 10AK80 APTCD /D/ 07FEATURE,OUTPUT,FILTERED FILTERED OUTPUT FEATURE AN INDICATION OF WHETHER OR NOT A FILTER OUTPUT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 APTDD 18TYPE,END END TYPE INDICATES THE TYPE OF END. SELECT REPLY CODE 10AK84 APTEJ 04DIAMETER,FLANGE,MOUNTING MOUNTING FLANGE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MOUNTING FLANGE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 APTFJ 04DIAMETER,BODY,METER METER BODY DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE METER BODY AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 APTGJ 04LENGTH,BODY,METER METER BODY LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE METER BODY,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 APTHJ 04WIDTH,BODY,METER METER BODY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE METER BODY, IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 APTJD /D/ 18TYPE,WIRE,NEUTRAL NEUTRAL WIRE TYPE INDICATES THE TYPE OF GROUND WIRE USED. SELECT REPLY CODE 10AA45 APTKD /D/ 18TYPE,CONTACT,SWITCH SWITCH CONTACT TYPE INDICATES THE TYPE OF CONTACT/S/ UTILIZED BY A SWITCH. SELECT REPLY CODE 10AC82 APTLJ /D/ 10CAPACITY,INTERRUPTING,CURRENT CURRENT INTERRUPTING CAPACITY THE AMOUNT OF CURRENT THE ITEM IS DESIGNED TO INTERRUPT. 1D AND 1B MODE REPLY13AK09 APTMD /D/ 18TYPE,RELEASE,TRIP,MANUAL MANUAL TRIP RELEASE TYPE INDICATES THE TYPE OF MANUAL TRIP RELEASE PROVIDED. SELECT REPLY CODE 10AH83 APTNJ 04DEPTH TO MOUNTING FLANGE,METER METER DEPTH TO MOUNTING FLANGE A MEASUREMENT BETWEEN THE MOUNTING FLANGE AND THE FACE OF THE ITEM, IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 APTPJ 10BANDWIDTH,INPUT FREQUENCY INPUT FREQUENCY BANDWIDTH THE NUMBER OF CYCLES PER SECOND /HERTZ/ EXPRESSING THE DIFFERENCES BETWEEN THE LIMITING FREQUENCIES OF AN INPUT BAND. 2D AND 1B MODE REPLY21AC321AC20 APTQJ 10FREQUENCY RATING,INPUT INPUT FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE INPUT IS RATED. 2D AND 1B MODE REPLY21AC321AC20 APTRJ 10BANDWIDTH,OUTPUT FREQUENCY OUTPUT FREQUENCY BANDWIDTH THE NUMBER OF CYCLES PER SECOND /HERTZ/ EXPRESSING THE DIFFERENCES BETWEEN THE LIMITING FREQUENCIES OF AN OUTPUT BAND. 2D AND 1B MODE REPLY21AC321AC20 APTSJ 10FREQUENCY RATING,OUTPUT OUTPUT FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE OUTPUT IS RATED. 2D AND 1B MODE REPLY21AC321AC20 APTTJ 10FREQUENCY,OPERATING OPERATING FREQUENCY THE FREQUENCY AT WHICH THE ITEM FUNCTIONS. 2D AND 1B MODE REPLY21AC321AC20 APTWD 18TYPE,LINE,TRANSMISSION TRANSMISSION LINE TYPE INDICATES THE TYPE OF LINE USED TO TRANSMIT SIGNALS OR ENERGY FROM ONE LOCATION TO ANOTHER. SELECT REPLY CODE 10AK75 APTXD 19FEATURE,TAX TAX FEATURE THE TAX FEATURE OF THE ITEM. SELECT REPLY CODE 10AK78 APTYD /D/ 07CHARACTERISTIC,MENTHOLATED MENTHOLATED CHARACTERISTIC AN INDICATION OF WHETHER OR NOT THE ITEM CONTAINS MENTHOL. SELECT REPLY CODE 10AA49 APTZD 03DESIGNATION,KEY KEY DESIGNATION THE TONE/SOUND BY WHICH THE ITEM IS IDENTIFIED. SELECT REPLY CODE 10AH87 APWAD /D/ 07MOUTHPIECE MOUTHPIECE AN INDICATION OF WHETHER OR NOT A MOUTHPIECE IS INCLUDED. SELECT REPLY CODE 10AA49 APWBD /D/ 07LYRE LYRE AN INDICATION OF WHETHER OR NOT A LYRE IS INCLUDED. SELECT REPLY CODE 10AA49 APWCD /D/ 07STRAP,NECK NECK STRAP AN INDICATION OF WHETHER OR NOT A NECK STRAP IS INCLUDED. SELECT REPLY CODE 10AA49 APWDD 03DESIGNATION,MODEL MODEL DESIGNATION THE TERM BY WHICH THE ITEM IS IDENTIFIED. SELECT REPLY CODE 10AK79 APWEA 12QUANTITY,DISK DISK QUANTITY THE NUMBER OF DISKS INCLUDED WITH THE ITEM. 1A MODE REPLY 0 APWFD /D/ 18TYPE,CYMBAL CYMBAL TYPE INDICATES THE TYPE OF CYMBAL. SELECT REPLY CODE 10AK81 APWGD 03DESIGNATOR,WEIGHT WEIGHT DESIGNATOR A DESIGNATION INDICATING THE HEAVINESS OF AN ITEM. SELECT REPLY CODE 10AJ89 APWHD /D/ 07PAIRS,MATCHED MATCHED PAIRS AN INDICATION OF WHETHER OR NOT THE ITEM IS FURNISHED IN MATCHED PAIRS. SELECT REPLY CODE 10AA55 APWKD 03DESIGNATION,SOUND SOUND DESIGNATION THE TERM BY WHICH A SPECIFIC SOUND IS IDENTIFIED. SELECT REPLY CODE 10AK83 APWLL 16STYLE,NEEDLE,ARMED SUTURE ARMED SUTURE NEEDLE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF AN ARMED SUTURE NEEDLE. 1L MODE REPLY 0 APWMJ /D/ 10FREQUENCY RATING,RADIO/VIDEO RADIO/VIDEO FREQUENCY RATING THE NUMBER OF COMPLETE CYCLE CHANGES OF RADIATED ENERGY,PER UNIT OF TIME,FOR WHICH AN ITEM IS RATED. 2D AND 1B MODE REPLY21AC321AC20 APWNJ 10FREQUENCY RATING,RECEIVER RECEIVER FREQUENCY RATING THE NUMBER OF COMPLETE CYCLE CHANGES OF RADIATED ENERGY,PER UNIT OF TIME,FOR WHICH THE RECEIVER IS RATED. 2D AND 1B MODE REPLY21AC321AC20 APWPJ 10FREQUENCY RATING,TRANSMITTER TRANSMITTER FREQUENCY RATING THE NUMBER OF COMPLETE CYCLE CHANGES OF RADIATED ENERGY,PER UNIT OF TIME,FOR WHICH THE TRANSMITTER IS RATED. 2D AND 1B MODE REPLY21AC321AC20 APWQJ A18TYPE AND QUANTITY,BAND,FREQUENCY FREQUENCY BAND TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF FREQUENCY BANDS. 1D AND 1A MODE REPLY12AK27 APWRJ A18TYPE AND QUANTITY,CHANNEL,FREQUENCY FREQUENCY CHANNEL TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF FREQUENCY CHANNELS. 1D AND 1A MODE REPLY12AK27 APWSH /D/ 18TYPE,EMISSION EMISSION TYPE A CLASSIFICATION OF RADIO FREQUENCY EMISSION IN WHICH THE MODULATION,TRANSMISSION,AND/OR SUPPLEMENTARY CHARACTERISTICS ARE REPRESENTED BY SYMBOLS. 2D MODE REPLY 23AJ762AK27 APWTD /D/ 07MODULATION,SIGNAL,RETRANSMITTED RETRANSMITTED SIGNAL MODULATION AN INDICATION OF WHETHER OR NOT MODULATION IS INCLUDED TO THE RETRANSMITIED SIGNAL. SELECT REPLY CODE 10AA49 APWWD /D/ 03DESIGNATION,WIDTH,FOOTWEAR FOOTWEAR WIDTH DESIGNATION AN INDICATION OF THE FOOTWEAR WIDTH DESIGNATION. SELECT REPLY CODE 10AK85 APWXG /D/ 03DESIGNATION,COMMERCIAL,OUTSOLE MATERIAL OUTSOLE MATERIAL COMMERCIAL DESIGNATION AN INDICATION OF THE OUTSOLE MATERIAL COMMERCIAL DESIGNATION. FULL TEXT WRITE-IN 0 APWYG /D/ 03DESIGNATION,COMMERCIAL,COVERSOLE AND VAMP MATERIAL COVERSOLE AND VAMP MATERIAL COMMERCIAL DESIGNATION THE DESIGNATION BY WHICH THE COVERSOLE AND VAMP MATERIAL IS COMMERCIALLY KNOWN OR IDENTIFIED. FULL TEXT WRITE-IN 0 APWZD /D/ 09MATERIAL,TAPE TAPE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TAPE IS FABRICATED. SELECT REPLY CODE 10AD09 APXAD 03DESIGNATOR,USER USER DESIGNATOR A DESIGNATION INDICATING THE PERSONNEL,ORGANIZATION,PROFESSION,TRADE,AND THE LIKE,FOR WHICH AN ITEM IS SPECIFICALLY DESIGNED. SELECT REPLY CODE 10AL31 APXBJ /D/ 04LENGTH,TAPE,TYING TYING TAPE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TYING TAPE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 APXCD /D/ 19ADJUSTMENT,TIME TIME ADJUSTMENT AN INDICATION OF THE TIME ADJUSTMENT. SELECT REPLY CODE 10AH00 APXDA /D/ 19IDENTIFICATION,SHADE,TRIM TRIM SHADE IDENTIFICATION A DESIGNATION ASSIGNED TO A PARTICULAR GRADATION OF A TRIM COLOR FOR THE PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 APXED /D/ 19SOURCE,SHADE,TRIM TRIM SHADE SOURCE THE NAME OF THE REFERENCE SOURCE OF THE TRIM SHADE IDENTIFICATION DESIGNATOR. SELECT REPLY CODE 10AF94 APXFD /D/ 07RELEASE,TRIP,SHUNT SHUNT TRIP RELEASE AN INDICATION OF WHETHER OR NOT A SHUNT TRIP RELEASE IS PROVIDED. SELECT REPLY CODE 10AB22 APXGD /D/ 18TYPE,RELEASE,TRIP,AUTOMATIC AUTOMATIC TRIP RELEASE TYPE INDICATES THE TYPE OF AUTOMATIC TRIP RELEASE PROVIDED. SELECT REPLY CODE 10AH83 APXHD /D/ 08LOCATION,TERMINAL TERMINAL LOCATION THE POSITION OF THE TERMINAL/S/ FOR MAKING CONNECTION TO AN ITEM.PLEASE USE MRC CQTM IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AJ91 APXJJ /D/ 10CURRENT RATING,TRIPPING,MINIMUM MINIMUM TRIPPING CURRENT RATING THE MINIMUM CURRENT RATING OR PERCENT AT WHICH THE ITEM OPERATES. 1D AND 1B MODE REPLY12AK86 APXKD 01COLOR,SHELL SHELL COLOR THE HUE OR TINT OF THE SHELL. SELECT REPLY CODE 10AD06 APXLD /D/ 01COLOR,TRIM TRIM COLOR THE HUE OR TINT OF THE TRIM. SELECT REPLY CODE 10AD06 APXMD /D/ 02DESIGN,FOOTWEAR FOOTWEAR DESIGN THE DESIGN OF THE FOOTWEAR. SELECT REPLY CODE 10AK54 APXND 19SIZE,FOOTWEAR FOOTWEAR SIZE A DESIGNATION INDICATING ONE OF A SERIES OF GRADUATED CLASSIFICATIONS OF MANUFACTURED FOOTWEAR ITEMS IDENTIFIED BY NUMBER,LETTER,AND/OR WORD,EACH REPRESENTING A DIMENSION. SELECT REPLY CODE 10AF81 APXPD /D/ 07FINISH,PEARL,SHELL SHELL PEARL FINISH AN INDICATION OF WHETHER OR NOT A SHELL PEARL FINISH IS INCLUDED. SELECT REPLY CODE 10AA49 APXRG /D/ 19RECORDED,ARTIST/SOUND ARTIST/SOUND RECORDED AN INDICATION OF THE ARTIST AND/OR SOUND RECORDED. FULL TEXT WRITE-IN 0 APXSG 19DATE,RECORDING RECORDING DATE THE DATE OF THE RECORDING. FULL TEXT WRITE-IN 0 APXTA 12QUANTITY,REEL REEL QUANTITY THE NUMBER OF REELS INCLUDED. 1A MODE REPLY 0 APXWG 19MARKINGS,REEL REEL MARKINGS MARKING/S/ INCLUDED ON THE ITEM FOR THE PURPOSE OF READY IDENTIFICATION. FULL TEXT WRITE-IN 0 APXXJ /D/ 04LENGTH,TAPE TAPE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TAPE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 APXYJ /D/ 04THICKNESS,TAPE TAPE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE TAPE,IN DISTINCTION FROM LENGTH AND WIDTH. 2D AND 1B MODE REPLY21AA051AC20 APXZJ /D/ 04DIAMETER,REEL REEL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE REEL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 APYAJ /D/ 10TIME,PLAYING PLAYING TIME THE PLAYING TIME OF THE ITEM. 1D AND 1B MODE REPLY12AH68 APYBD /D/ 07FEATURE,VENTILATION VENTILATION FEATURE AN INDICATION OF WHETHER OR NOT A VENTILATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 APYCA /D/ 03DESIGNATION,WIDTH WIDTH DESIGNATION A MEASUREMENT EXPRESSED AS A NUMERIC OR LETTERED REPLY FOR DESIGNATING THE WIDTH OF AN ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1A MODE REPLY 0 APYDA 04THICKNESS IN IRONS THICKNESS IN IRONS A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 1A MODE REPLY 0 APYED 18TYPE,DETECTOR DETECTOR TYPE INDICATES THE SPECIFIC TYPE OF DETECTOR INCLUDED. SELECT REPLY CODE 10AK80 APYFD 19FLEXIBILITY,RADOME RADOME FLEXIBILITY FLEXIBLE,CAPABLE OF BEING BENT,TURNED,OR TWISTED WITHIN LIMITS WITHOUT BREAKING;OR RIGID,RESISTING CHANGE OF FORM,INFLEXIBLE. SELECT REPLY CODE 10AD03 APYGD 14SHAPE,RADOME,INFLATED INFLATED RADOME SHAPE THE PHYSICAL CONFIGURATION OF THE RADOME WHEN INFLATED. SELECT REPLY CODE 10AD07 APYHD /D/ 09MATERIAL,RADOME RADOME MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE RADOME IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 APYJD /D/ 07DEVICE,PRESSURIZING PRESSURIZING DEVICE AN INDICATION OF WHETHER OR NOT A PRESSURIZING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 APYKD /D/ 07PROVISION,DE-ICING DE-ICING PROVISION AN INDICATION OF WHETHER OR NOT A DE-ICING PROVISION IS INCLUDED. SELECT REPLY CODE 10AA49 APYLD 18TYPE,COUNTERPOISE COUNTERPOISE TYPE INDICATES THE TYPE OF COUNTERPOISE. SELECT REPLY CODE 10AK90 APYMA 12QUANTITY,ELEMENT,CONDUCTOR CONDUCTOR ELEMENT QUANTITY THE NUMBER OF CONDUCTOR ELEMENTS. 1A MODE REPLY 0 APYNA 04SIZE,WIRE,AWG AWG WIRE SIZE THE AMERICAN WIRE GAGE SIZE OF WIRE THE FACILITY FOR ATTACHING A WIRE WILL ACCOMMODATE. 1A MODE REPLY 0 APYPD /D/ 09MATERIAL,INSULATION,CONDUCTOR CONDUCTOR INSULATION MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CONDUCTOR INSULATION IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT.REPLACE WITH MRC MASU ISAC TO TABLE 0298 SELECT REPLY CODE 10AD09 APYQD /D/ 09MATERIAL,CONDUCTOR CONDUCTOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CONDUCTOR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT.REPLACE WITH MRC MATT ISAC TO TABLE 0298 SELECT REPLY CODE 10AD09 APYRD 19CONSTRUCTION,CONDUCTOR CONDUCTOR CONSTRUCTION THE CONSTRUCTION OF THE CONDUCTOR. SELECT REPLY CODE 10AA45 APYSJ 04LENGTH,CONDUCTOR CONDUCTOR LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CONDUCTOR,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 APYTJ 04WIDTH,CONDUCTOR CONDUCTOR WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A CONDUCTOR,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 APYWJ 04HEIGHT,MAXIMUM MAXIMUM HEIGHT THE MAXIMUM MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE ITEM,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 APYXJ 04HEIGHT,NESTED NESTED HEIGHT A MEASUREMENT FROM THE TOP TO THE BOTTOM OF AN ITEM WHEN NESTED,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 APYYJ 04DEPTH,BASE BASE DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE BASE OF AN ITEM,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 APYZJ 04DEPTH,TOP TOP DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE TOP OF AN ITEM,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 APZAJ 10CAPACITANCE IN PICOFARADS PER UNIT LENGTH CAPACITANCE IN PICOFARADS PER UNIT LENGTH THE ELECTRICAL CAPACITANCE MEASURED BETWEEN TWO SPECIFIED POINTS ON THE ITEM,EXPRESSED IN PICOFARADS PER UNIT LENGTH. 1D AND 1B MODE REPLY11AB39 APZBJ 10VOLTAGE RATING,OPERATING OPERATING VOLTAGE RATING THE VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY11AB63 APZCD /D/ 07CONDUCTOR,OUTER OUTER CONDUCTOR AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES AN OUTER CONDUCTOR. SELECT REPLY CODE 10AA49 APZDD 14SHAPE,SPACER,INSULATION INSULATION SPACER SHAPE THE PHYSICAL CONFIGURATION OF THE INSULATION SPACER. SELECT REPLY CODE 10AD07 APZEJ /D/ 10RANGE,CURRENT,TRIPPING TRIPPING CURRENT RANGE THE ADJUSTABLE LIMITS OF THE TRIPPING CURRENT. 1D AND 1B MODE REPLY12AK86 APZFB /D/ 10TEMP REQUIRED IN DEG CELSIUS,AMBIENT AMBIENT TEMP REQUIRED IN DEG CELSIUS THE AMBIENT TEMPERATURE REQUIRED FOR THE ITEM,EXPRESSED IN DEGREES CELSIUS. 1B MODE REPLY 0 APZGG /D/ 10TIME,TRIPPING TRIPPING TIME AN INDICATION OF THE AMOUNT OF ELAPSED TIME. FULL TEXT WRITE-IN 0 APZHD /D/ 11METHOD,CLOSING,CIRCUIT CIRCUIT CLOSING METHOD THE MEANS USED FOR CLOSING A CIRCUIT. SELECT REPLY CODE 10AK88 APZJD 19ARRANGEMENT,FIBER,STRAND STRAND FIBER ARRANGEMENT THE SPECIFIC ARRANGEMENT OF THE FIBERS TO FORM A STRAND. SELECT REPLY CODE 10AK87 APZKD /D/ 09MATERIAL,CONTACT,MAIN MAIN CONTACT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MAIN CONTACT/S/ IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 APZLD /D/ 09MATERIAL,CONTACT,ARCING ARCING CONTACT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ARCING CONTACT/S/ IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 APZMJ 10CAPACITY,WATER,POTABLE POTABLE WATER CAPACITY THE AMOUNT OF PURIFIED WATER THE ITEM IS CAPABLE OF PRODUCING FOR A GIVEN PERIOD OF TIME. 2D AND 1B MODE REPLY21AB101AC11 APZND /D/ 19SOURCE,SHADE,UPPER UPPER SHADE SOURCE THE NAME OF THE REFERENCE SOURCE OF THE UPPER SHADE IDENTIFICATION DESIGNATOR. SELECT REPLY CODE 10AF94 APZPA /D/ 19IDENTIFICATION,SHADE,UPPER UPPER SHADE IDENTIFICATION A DESIGNATION ASSIGNED TO A PARTICULAR GRADATION OF THE UPPER SHADE COLOR FOR THE PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 APZQD /D/ 18TYPE,CLOSING,MANUAL MANUAL CLOSING TYPE INDICATES THE TYPE OF DEVICE USED FOR MANUALLY CLOSING THE ITEM. SELECT REPLY CODE 10AH83 APZRD /D/ 07FEATURE,FREE,TRIP TRIP FREE FEATURE AN INDICATION OF WHETHER OR NOT A TRIP FREE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 APZSD 18TYPE,RESET RESET TYPE INDICATES THE TYPE OF RESET PROVIDED. SELECT REPLY CODE 10AC58 APZTD /D/ 18TYPE,RESET,MANUAL MANUAL RESET TYPE INDICATES THE TYPE OF MANUAL RESET PROVIDED. SELECT REPLY CODE 10AH83 APZWD /D/ 07POSITION,RESET,SEPARATE SEPARATE RESET POSITION AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A SEPARATE RESET POSITION. SELECT REPLY CODE 10AB22 APZXD 18TYPE,COVERING,PROTECTIVE PROTECTIVE COVERING TYPE INDICATES THE TYPE OF PROTECTIVE COVERING PROVIDED. SELECT REPLY CODE 10AK89 APZYD 08LOCATION,BLOCK,CIRCUIT PROTECTOR CIRCUIT PROTECTOR BLOCK LOCATION INDICATES THE LOCATION OF THE CIRCUIT PROTECTOR BLOCK. SELECT REPLY CODE 10AK91 APZZD /D/ 07FEATURE,PRESERVATION,STORAGE STORAGE PRESERVATION FEATURE AN INDICATION OF WHETHER OR NOT A PRESERVATION FEATURE FOR LONG TERM STORAGE IS INCLUDED. SELECT REPLY CODE 10AA49 AQAAA 12QUANTITY,EFFECT EFFECT QUANTITY THE NUMBER OF EFFECTS CONTAINED WITHIN THE ITEM. 1A MODE REPLY 0 AQABA 12QUANTITY,SHELL SHELL QUANTITY THE NUMBER OF SHELLS PROVIDED. 1A MODE REPLY 0 AQACD 18TYPE,SURFACE,EVAPORATION EVAPORATION SURFACE TYPE INDICATES THE TYPE OF SURFACE WHERE THE EVAPORATION PROCESS TAKES PLACE. SELECT REPLY CODE 10AK92 AQADD 14SHAPE,SURFACE,EVAPORATION EVAPORATION SURFACE SHAPE THE PHYSICAL CONFIGURATION OF THE EVAPORATION SURFACE. SELECT REPLY CODE 10AD07 AQAEB 10PRESSURE IN PSI,STEAM,OPERATING,FIRST EFFECT FIRST EFFECT OPERATING STEAM PRESSURE IN PSI THE REQUIRED OPERATING STEAM PRESSURE OF THE FIRST EFFECT,EXPRESSED IN POUNDS PER SQUARE INCH. 1B MODE REPLY 0 AQAFB 10PRESSURE IN PSI,STEAM,OPERATING,AIR EJECTOR AIR EJECTOR OPERATING STEAM PRESSURE IN PSI THE REQUIRED OPERATING STEAM PRESSURE OF THE AIR EJECTOR,EXPRESSED IN POUNDS PER SQUARE INCH. 1B MODE REPLY 0 AQAGA 12QUANTITY,COMPRESSOR,VAPOR VAPOR COMPRESSOR QUANTITY THE NUMBER OF VAPOR COMPRESSORS PROVIDED. 1A MODE REPLY 0 AQAHD 18TYPE,COMPRESSOR,VAPOR VAPOR COMPRESSOR TYPE INDICATES THE TYPE OF VAPOR COMPRESSOR PROVIDED. SELECT REPLY CODE 10AA80 AQAJJ 04DISTANCE,MINIMUM,TUBE REMOVAL TUBE REMOVAL MINIMUM DISTANCE THE MINIMUM SPACE OR DISTANCE FROM ONE ITEM TO ANOTHER ITEM REQUIRED TO FACILITATE REMOVAL OF THE TUBE/S/. 1D AND 1B MODE REPLY11AA05 AQAKD 08LOCATION,REMOVAL,TUBE TUBE REMOVAL LOCATION INDICATES THE LOCATION FROM WHICH THE TUBE/S/ IS REMOVED FROM THE UNIT. SELECT REPLY CODE 10AJ91 AQALB /D/ 10CAPACITY IN CUBIC FEET PER MINUTE,COMPRESSOR,VAPOR VAPOR COMPRESSOR CAPACITY IN CUBIC FEET PER MINUTE THE RATED CAPACITY OF THE VAPOR COMPRESSOR,EXPRESSED IN CUBIC FEET PER MINUTE. 1B MODE REPLY 0 AQAMJ 10OVERLOAD RATING IN AMPS OVERLOAD RATING IN AMPS THE VALUE AT WHICH THE OVERLOAD IS RATED,EXPRESSED IN AMPERES. 1D AND 1B MODE REPLY11AC20 AQANA 12QUANTITY,WIRE WIRE QUANTITY THE NUMBER OF WIRES THE ITEM CAN ACCOMMODATE. 1A MODE REPLY 0 AQAPD 18TYPE,ARRESTER ARRESTER TYPE INDICATES THE TYPE OF ARRESTER. SELECT REPLY CODE 10AK80 AQAQJ 10VOLTAGE,BREAKDOWN BREAKDOWN VOLTAGE THE VOLTAGE AT WHICH THE ITEM WILL BREAK DOWN. 2D AND 1B MODE REPLY21AB631AC20 AQARJ 10VOLTAGE,LINE TO GROUND LINE TO GROUND VOLTAGE AN INDICATION OF THE LINE TO GROUND VOLTAGE. 2D AND 1B MODE REPLY21AB631AC20 AQASD /D/ 07PROVISION,COVER COVER PROVISION AN INDICATION OF WHETHER OR NOT A COVER IS PROVIDED. SELECT REPLY CODE 10AB22 AQATA 12QUANTITY,FUSE FUSE QUANTITY THE NUMBER OF FUSES PROVIDED. 1A MODE REPLY 0 AQAWD /D/ 18TYPE,TERMINAL,PANEL PANEL TERMINAL TYPE INDICATES THE SPECIFIC TYPE OF TERMINAL/S/ ON THE PANEL. SELECT REPLY CODE 10AA58 AQAXD /D/ 18TYPE,ENTRANCE,UNTHREADED UNTHREADED ENTRANCE TYPE INDICATES THE TYPE OF UNTHREADED OPENING/S/ PROVIDED. SELECT REPLY CODE 10AK60 AQAYJ 10CAPACITY,INTERRUPTING,CURRENT CURRENT INTERRUPTING CAPACITY THE AMOUNT OF CURRENT THE ITEM IS DESIGNED TO INTERRUPT. 2D AND 1B MODE REPLY23AK091AC20 AQAZD /D/ 09MATERIAL,SPACER,INSULATION INSULATION SPACER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE FROM WHICH THE INSULATION SPACER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AQBAJ 04DIAMETER,OUTSIDE,INSULATION SPACER INSULATION SPACER OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INSULATION SPACER,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AQBBG /D/ 19AGENCY,CONTROLLING,TERMINATION TERMINATION CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE TERMINATION. FULL TEXT WRITE-IN 0 AQBCD 19DEVICE,OPERATED,ELECTRICAL ELECTRICAL OPERATED DEVICE AN INDICATION OF THE ELECTRICAL OPERATED DEVICE. SELECT REPLY CODE 10AH83 AQBDD /D/ 07FITTING,TERMINAL TERMINAL FITTING AN INDICATION OF WHETHER OR NOT A TERMINAL FITTING/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 AQBEG 11METHOD,PROCESSING,END END PROCESSING METHOD THE MEANS USED TO PROCESS THE ENDS. FULL TEXT WRITE-IN 0 AQBFG 03DESIGNATOR,CRYSTAL CRYSTAL DESIGNATOR A DESIGNATION BY WHICH THE CRYSTAL IS COMMERICALLY KNOWN AND/OR IDENTIFIED. FULL TEXT WRITE-IN 0 AQBGB 10CURRENT RATING IN MILLIAMPERES,NOMINAL,CRYSTAL CRYSTAL NOMINAL CURRENT RATING IN MILLIAMPERES THE AVERAGE CURRENT RATING FOR WHICH THE CRYSTAL IS RATED,EXPRESSED IN MILLIAMPERES. 1B MODE REPLY 0 AQBHD /D/ 07MECHANISM,RIBBON RIBBON MECHANISM AN INDICATION OF WHETHER OR NOT A RIBBON MECHANISM IS INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA49 AQBJG /D/ 03DESIGNATOR,TERMINAL,SIGNAL INPUT SIGNAL INPUT TERMINAL DESIGNATOR A DESIGNATION ASSIGNED TO THE SIGNAL INPUT TERMINAL FOR THE PURPOSE OF IDENTIFICATION. FULL TEXT WRITE-IN 0 AQBKG /D/ 03DESIGNATOR,TERMINAL,LOCAL OSCILLATOR INPUT LOCAL OSCILLATOR INPUT TERMINAL DESIGNATOR A DESIGNATION ASSIGNED TO THE LOCAL OSCILLATOR INPUT TERMINAL FOR THE PURPOSE OF IDENTIFICATION. FULL TEXT WRITE-IN 0 AQBLG /D/ 03DESIGNATOR,TERMINAL,SIGNAL OUTPUT SIGNAL OUTPUT TERMINAL DESIGNATOR A DESIGNATION ASSIGNED TO THE SIGNAL OUTPUT TERMINAL FOR THE PURPOSE OF IDENTIFICATION. FULL TEXT WRITE-IN 0 AQBMD 07ADJUSTABILITY,INPUT,LOCAL OSCILLATOR LOCAL OSCILLATOR INPUT ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE LOCAL OSCILLATOR INPUT IS ADJUSTABLE. SELECT REPLY CODE 10AB00 AQBND /D/ 07FEATURE,NOISELESS NOISELESS FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES A NOISELESS FEATURE. SELECT REPLY CODE 10AA49 AQBPD /D/ 07SPACING,PROPORTIONAL PROPORTIONAL SPACING AN INDICATION OF WHETHER OR NOT PROPORTIONAL SPACING IS PROVIDED. SELECT REPLY CODE 10AB22 AQBQD /D/ 07FEATURE,TABULATOR,DECIMAL DECIMAL TABULATOR FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES A DECIMAL TABULATOR. SELECT REPLY CODE 10AA49 AQBRD /D/ 07DEVICE,RULING,AUTOMATIC FORM AUTOMATIC FORM RULING DEVICE AN INDICATION OF WHETHER OR NOT AN AUTOMATIC FORM RULING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 AQBSD 18TYPE,CONNECTOR,EXTERNAL EXTERNAL CONNECTOR TYPE INDICATES THE TYPE OF EXTERNAL CONNECTOR PROVIDED. SELECT REPLY CODE 10AK93 AQBTD 18TYPE,CONNECTOR,INTERNAL CONDUCTOR INTERNAL CONDUCTOR CONNECTOR TYPE INDICATES THE TYPE OF INTERNAL CONDUCTOR CONNECTOR PROVIDED. SELECT REPLY CODE 10AK93 AQBWD 18TYPE,SIGNAL,AUDIBLE AUDIBLE SIGNAL TYPE INDICATES THE TYPE OF DEVICE THAT PROVIDES AN AUDIBLE SIGNAL. SELECT REPLY CODE 10AJ12 AQBXB 10PRESSURE IN PSI,GAS,MAXIMUM MAXIMUM GAS PRESSURE IN PSI THE MAXIMUM GAS PRESSURE THE ITEM IS DESIGNED TO ACCOMMODATE,EXPRESSED IN POUNDS PER SQUARE INCH. 1B MODE REPLY 0 AQBYJ 04DIAMETER,OPENING,TRANSMISSION LINE TRANSMISSION LINE OPENING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TRANSMISSION LINE OPENING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AQBZA 12QUANTITY,CONNECTOR CONNECTOR QUANTITY THE NUMBER OF CONNECTORS PROVIDED. 1A MODE REPLY 0 AQCAD 18TYPE,FLANGE FLANGE TYPE INDICATES THE TYPE OF FLANGE PROVIDED. SELECT REPLY CODE 10AG92 AQCBA /D/ 13THREAD SIZE,HOLE,FLANGE CONNECTING FLANGE CONNECTING HOLE THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER INCH OF THE FLANGE CONNECTING HOLE. 1A MODE REPLY 0 AQCCG 04SPACING,HOLE,CONNECTING FLANGE FLANGE CONNECTING HOLE SPACING THE NARRATIVE EXPRESSION USED FOR INDICATING THE SPACING OF THE FLANGE CONNECTING HOLES. FULL TEXT WRITE-IN 0 AQCDB 10DISPLACEMENT BETWEEN FLANGE CONTACT SURFACES IN DEG,ANGULAR ANGULAR DISPLACEMENT BETWEEN FLANGE CONTACT SURFACES IN DEG THE MEASUREMENT OF THE DIFFERENCE OF POSITION BETWEEN THE CONTACT SURFACES OF THE FLANGES,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AQCED 18TYPE,CONDUCTOR,ACCOMMODATED ACCOMMODATED CONDUCTOR TYPE INDICATES THE TYPE OF CONDUCTOR THE ITEM IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AL01 AQCFD 11METHOD,CONNECTION CONNECTION METHOD THE MEANS USED TO CONNECT THE ITEM. SELECT REPLY CODE 10AJ68 AQCGJ 04LENGTH,THROAT THROAT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE THROAT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AQCHJ 04WIDTH,THROAT THROAT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE THROAT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AQCJJ 04DIAMETER,THROAT THROAT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THROAT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AQCKJ 04HEIGHT,THROAT THROAT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE THROAT,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AQCLJ 04DEPTH,THROAT THROAT DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE THROAT,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AQCMJ 04LENGTH,MOUTH MOUTH LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUTH,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AQCNJ 04WIDTH,MOUTH MOUTH WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUTH,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AQCPJ 04DIAMETER,MOUTH MOUTH DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MOUTH,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AQCQJ 04HEIGHT,MOUTH MOUTH HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE MOUTH,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AQCRJ 04DEPTH,MOUTH MOUTH DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE MOUTH,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AQCSD /D/ 07PROTECTION,HERMETIC HERMETIC PROTECTION AN INDICATION OF WHETHER OR NOT A HERMETIC PROTECTION IS PROVIDED. SELECT REPLY CODE 10AB22 AQCTD /D/ 07CAPACITOR,SHUNT SHUNT CAPACITOR AN INDICATION OF WHETHER OR NOT A SHUNT CAPACITOR IS INCLUDED. SELECT REPLY CODE 10AA49 AQCWD /D/ 09MATERIAL,ELEMENT ELEMENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ELEMENT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AQCXB /D/ 10RPM,COMPRESSOR,VAPOR VAPOR COMPRESSOR RPM THE NUMBER OF REVOLUTIONS PER MINUTE FOR WHICH THE VAPOR COMPRESSOR IS RATED. 1B MODE REPLY 0 AQCYD /D/ 18TYPE,HEATER,STARTING STARTING HEATER TYPE INDICATES THE TYPE OF STARTING HEATER PROVIDED. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AA93 AQCZD 02DESIGN,EVAPORATOR EVAPORATOR DESIGN THE DESIGN OF THE EVAPORATOR. SELECT REPLY CODE 10AK94 AQDAD /D/ 07STABILIZER,BRINE BRINE STABILIZER AN INDICATION OF WHETHER OR NOT A BRINE STABILIZER IS INCLUDED. SELECT REPLY CODE 10AA49 AQDBD 18TYPE,UNIT,DISINFECTION DISINFECTION UNIT TYPE INDICATES THE TYPE OF DISINFECTION UNIT PROVIDED. SELECT REPLY CODE 10AK96 AQDCA 12QUANTITY,UNIT,DISINFECTION DISINFECTION UNIT QUANTITY THE NUMBER OF DISINFECTION UNITS PROVIDED. 1A MODE REPLY 0 AQDDD 18TYPE,FEED FEED TYPE INDICATES THE TYPE OF FEED PROVIDED. SELECT REPLY CODE 10AK97 AQDED 18TYPE,CONTROL,FEED FEED CONTROL TYPE INDICATES THE TYPE OF FEED CONTROL PROVIDED. SELECT REPLY CODE 10AK03 AQDFJ 10FEED RATE,MAXIMUM MAXIMUM FEED RATE THE MAXIMUM AMOUNT THE ITEM WILL FEED IN A GIVEN PERIOD OF TIME. 2D AND 1B MODE REPLY21AB101AC11 AQDGD /D/ 07POT,CHEMICAL CHEMICAL POT AN INDICATION OF WHETHER OR NOT A CHEMICAL POT(S) IS PROVIDED. SELECT REPLY CODE 10AB22 AQDHD 18TYPE,EQUIPMENT,PRETREATMENT PRETREATMENT EQUIPMENT TYPE INDICATES THE TYPE OF PRETREATMENT EQUIPMENT PROVIDED. SELECT REPLY CODE 10AK98 AQDJD 18TYPE,CLARIFIER,SOLID CONTACT SOLID CONTACT CLARIFIER TYPE INDICATES THE TYPE OF SOLID CONTACT CLARIFIER. SELECT REPLY CODE 10AK99 AQDKJ 10CURRENT RATING,ABSORBER ABSORBER CURRENT RATING THE AMOUNT OF CURRENT FOR WHICH THE ABSORBER IS RATED. 2D AND 1B MODE REPLY21AC301AC20 AQDLB 10CURRENT RATING IN AMPS,MAXIMUM,PROTECTED ITEM PROTECTED ITEM MAXIMUM CURRENT RATING IN AMPS THE MAXIMUM CURRENT RATING OF THE ITEM BEING PROTECTED,EXPRESSED IN AMPERES. 1B MODE REPLY 0 AQDMB 10AREA IN SQUARE FEET,SEPARATION,SLURRY SLURRY SEPARATION AREA IN SQUARE FEET THE EFFECTIVE AREA THAT THE SLURRY WILL SEPARATE TURBIDITY WITHIN THE UNIT,EXPRESSED IN SQUARE FEET. 1B MODE REPLY 0 AQDND 19NAME,ITEM,PROTECTED PROTECTED ITEM NAME THE NAME OF THE ITEM WHICH IS BEING PROTECTED. SELECT REPLY CODE 10AL00 AQDPB 10VOLUME IN GALLONS,TOTAL TOTAL VOLUME IN GALLONS THE TOTAL VOLUME OF FLUID THAT THE UNIT IS DESIGNED TO ACCOMMODATE,EXPRESSED IN GALLONS. 1B MODE REPLY 0 AQDQD /D/ 07FEATURE,INDICATING INDICATING FEATURE AN INDICATION OF WHETHER OR NOT AN INDICATING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AQDRD 11METHOD,RECLOSING RECLOSING METHOD THE MEANS BY WHICH RECLOSURE IS EFFECTED. SELECT REPLY CODE 10AC58 AQDTA /D/ 12QUANTITY,CIRCUIT,BRANCH BRANCH CIRCUIT QUANTITY THE NUMBER OF BRANCH CIRCUITS PROVIDED. 1A MODE REPLY 0 AQDWD /D/ 07FEATURE,NEUTRAL NEUTRAL FEATURE AN INDICATION OF WHETHER OR NOT A NEUTRAL FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AQDXD 18TYPE,TENT TENT TYPE INDICATES THE SPECIFIC TYPE OF TENT PROVIDED. SELECT REPLY CODE 10AL02 AQDYD 08LOCATION,MATERIAL,COATING COATING MATERIAL LOCATION INDICATES THE LOCATION ON THE ITEM TO WHICH A COATING HAS BEEN APPLIED. SELECT REPLY CODE 10AJ91 AQDZG 19NAME,COMPONENT,PROTECTIVE PROTECTIVE COMPONENT NAME AN INDICATION OF THE PROTECTIVE PART NAME ACCOMMODATED BY THE ITEM. FULL TEXT WRITE-IN 0 AQEAD /D/ 07COMPONENT,PROTECTIVE PROTECTIVE COMPONENT AN INDICATION OF WHETHER OR NOT PROTECTIVE COMPONENTS ARE INCLUDED. SELECT REPLY CODE 10AA49 AQEBA 12QUANTITY,COMPONENT,PROTECTIVE PROTECTIVE COMPONENT QUANTITY THE NUMBER OF PROTECTIVE COMPONENTS PROVIDED. 1A MODE REPLY 0 AQECD 18TYPE,MOVEMENT MOVEMENT TYPE INDICATES THE TYPE OF MOVEMENT PROVIDED. SELECT REPLY CODE 10AL03 AQEDD /D/ 07FEATURE,SELF-START SELF-START FEATURE AN INDICATION OF WHETHER OR NOT A SELF-STARTING FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AQEFD /D/ 07ELEMENT,HEATING,INTEGRAL INTEGRAL HEATING ELEMENT AN INDICATION OF WHETHER OR NOT AN INTEGRAL HEATING ELEMENT IS INCLUDED. SELECT REPLY CODE 10AA49 AQEGD /D/ 07DEVICE,STAND-BY,CURRENT FAILURE CURRENT FAILURE STAND-BY DEVICE AN INDICATION OF WHETHER OR NOT A CURRENT FAILURE STAND-BY DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 AQEHD /D/ 07REGULATION,POINT,CENTRAL CENTRAL POINT REGULATION AN INDICATION OF WHETHER OR NOT A MEANS OF REGULATING THE ELECTRICAL MOVEMENT FROM A CENTRAL POINT IS PROVIDED. SELECT REPLY CODE 10AB22 AQEJD 18TYPE,MOVEMENT,MECHANICAL MECHANICAL MOVEMENT TYPE INDICATES THE TYPE OF MECHANICAL MOVEMENT PROVIDED. SELECT REPLY CODE 10AL03 AQEKJ 10WEIGHT,MATERIAL,COATED COATED MATERIAL WEIGHT A RELATIVE MEASURE OF THE MASS OF AN ITEM WITH RESPECT TO ITS DENSITY AFTER COATING. 2D AND 1B MODE REPLY22AG691AC20 AQELD 18TYPE,ESCAPEMENT ESCAPEMENT TYPE INDICATES THE TYPE OF ESCAPEMENT PROVIDED. SELECT REPLY CODE 10AL04 AQEMA 12QUANTITY,DEVICE,SIGNAL SIGNAL DEVICE QUANTITY THE NUMBER OF SIGNALLING DEVICES PROVIDED. 1A MODE REPLY 0 AQEND 18TYPE,SIGNAL,VISUAL VISUAL SIGNAL TYPE INDICATES THE TYPE OF SIGNALLING DEVICE THAT PROVIDES A VISUAL SIGNAL. SELECT REPLY CODE 10AJ52 AQEPD 01COLOR,SIGNAL,VISUAL VISUAL SIGNAL COLOR A CHARACTERISTIC OF LIGHT,APPLICABLE TO THE VISUAL SIGNAL,THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY. SELECT REPLY CODE 10AD06 AQEQD 19MOUNTING,BOX,RELAY RELAY BOX MOUNTING AN INDICATION OF THE RELAY BOX MOUNTING. SELECT REPLY CODE 10AB28 AQERJ 04LENGTH,OVERALL,RELAY BOX RELAY BOX OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE RELAY BOX. 2D AND 1B MODE REPLY21AA051AC20 AQESJ 04WIDTH,OVERALL,RELAY BOX RELAY BOX OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A RELAY BOX,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AQETJ /D/ 04DIAMETER,OVERALL,RELAY BOX RELAY BOX OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE CENTER OF A RELAY BOX. 2D AND 1B MODE REPLY21AA051AC20 AQEWJ 04HEIGHT,OVERALL,RELAY BOX RELAY BOX OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF A RELAY BOX. 2D AND 1B MODE REPLY21AA051AC20 AQEXJ 04DEPTH,OVERALL,RELAY BOX RELAY BOX OVERALL DEPTH AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF A RELAY BOX,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AQEYD 18TYPE,ALARM ALARM TYPE INDICATES THE TYPE OF ALARM PROVIDED. SELECT REPLY CODE 10AJ12 AQEZD 18TYPE,MONITOR MONITOR TYPE INDICATES THE TYPE OF MONITOR PROVIDED. SELECT REPLY CODE 10AJ52 AQFAD 18TYPE,CHAMBER,SOUND SOUND CHAMBER TYPE INDICATES THE TYPE OF CHAMBER USED TO PRODUCE SOUND. SELECT REPLY CODE 10AL05 AQFBJ 04LENGTH,OVERALL,SOUND CHAMBER SOUND CHAMBER OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINUAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE SOUND CHAMBER. 2D AND 1B MODE REPLY21AA051AC20 AQFCJ 04DIAMETER,OVERALL,SOUND CHAMBER SOUND CHAMBER OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE CENTER OF A SOUND CHAMBER. 2D AND 1B MODE REPLY21AA051AC20 AQFDJ 04WIDTH,OVERALL,SOUND CHAMBER SOUND CHAMBER OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A SOUND CHAMBER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AQFEJ 04HEIGHT,OVERALL,SOUND CHAMBER SOUND CHAMBER OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE TOP TO THE BOTTOM OF A SOUND CHAMBER. 2D AND 1B MODE REPLY21AA051AC20 AQFFD 07ADJUSTABILITY,TONE TONE ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE TONE IS ADJUSTABLE. SELECT REPLY CODE 10AB00 AQFGD 02DESIGN,CLAPPER CLAPPER DESIGN THE DESIGN OF THE CLAPPER. SELECT REPLY CODE 10AG65 AQFHD /D/ 07BRACKET BRACKET AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A BRACKET(S). SELECT REPLY CODE 10AB22 AQFJD 07DETACHABILITY,BRACKET BRACKET DETACHABILITY AN INDICATION OF WHETHER OR NOT THE BRACKET IS DETACHABLE. SELECT REPLY CODE 10AH97 AQFKG 10LEVEL IN DECIBELS,LOUDNESS LOUDNESS LEVEL IN DECIBELS THE LEVEL OF A SIGNAL OR SOUND RELATIVE TO A SPECIFIC DISTANCE,EXPRESSED IN DECIBELS. FULL TEXT WRITE-IN 0 AQFLA 12QUANTITY,PROJECTOR,SOUND SOUND PROJECTOR QUANTITY THE NUMBER OF SOUND PROJECTORS PROVIDED. 1A MODE REPLY 0 AQFMD 18TYPE,PROJECTOR,SOUND SOUND PROJECTOR TYPE INDICATES THE SPECIFIC TYPE OF SOUND PROJECTOR PROVIDED. SELECT REPLY CODE 10AF31 AQFND /D/ 07BRACKET,MOUNTING MOUNTING BRACKET AN INDICATION OF WHETHER OR NOT A MOUNTING BRACKET IS PROVIDED. SELECT REPLY CODE 10AB22 AQFQD /D/ 18TYPE,HORN HORN TYPE INDICATES THE SPECIFIC TYPE OF HORN PROVIDED. SELECT REPLY CODE 10AB75 AQFRG 19INGREDIENT AND WEIGHT INGREDIENT AND WEIGHT THE NAME AND WEIGHT OF THE INDIVIDUAL INGREDIENTS THAT CONSTITUTE THE SUPPLY ITEM. FULL TEXT WRITE-IN 0 AQFSD /D/ 07FUSE,MULTIPLE,INTERNALLY CONNECTED INTERNALLY CONNECTED MULTIPLE FUSE AN INDICATION OF WHETHER OR NOT AN INTERNALLY CONNECTED MULTIPLE FUSE IS PROVIDED. SELECT REPLY CODE 10AB22 AQFTD /D/ 07SILENCER SILENCER AN INDICATION OF WHETHER OR NOT A SILENCER IS INCLUDED. SELECT REPLY CODE 10AA49 AQFWD /D/ 10INTERVAL,STRIKING STRIKING INTERVAL THE SPECIFIC TIME AND INTERVAL AT WHICH THE ITEM IS DESIGNED TO STRIKE OR INDICATE THE TIME MEASUREMENT BY MEANS OF SOUND. SELECT REPLY CODE 10AL14 AQFXD /D/ 07SILENCER,STRIKE STRIKE SILENCER AN INDICATION OF WHETHER OR NOT A STRIKE SILENCER IS INCLUDED. SELECT REPLY CODE 10AA49 AQFYD 01COLOR,BACKGROUND BACKGROUND COLOR THE HUE OR TINT OF THE BACKGROUND. SELECT REPLY CODE 10AD06 AQFZD 19NAME,SCALE SCALE NAME THE NOMENCLATURE BY WHICH THE SCALE IS IDENTIFIED. SELECT REPLY CODE 10AL15 AQGAG 19NAME,MANUFACTURER MANUFACTURER NAME THE NAME OF THE MANUFACTURER. FULL TEXT WRITE-IN 0 AQGBA /D/ 19NUMBER,IDENTIFYING,MANUFACTURER MANUFACTURER IDENTIFYING NUMBER THE NUMBER USED BY THE MANUFACTURER FOR IDENTIFYING THE ITEM. 1A MODE REPLY 0 AQGCJ A18TYPE AND QUANTITY,FEEDER,CHEMICAL CHEMICAL FEEDER TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF CHEMICAL FEEDERS PROVIDED. 1D AND 1A MODE REPLY12AL16 AQGDB /D/ 10EFFECTIVENESS IN SQUARE FEET,FILTER FILTER EFFECTIVENESS IN SQUARE FEET THE EFFECTIVE SURFACE AREA OF THE FILTER,EXPRESSED IN SQUARE FEET. 1B MODE REPLY 0 AQGED 18TYPE,CUTTER CUTTER TYPE INDICATES THE TYPE OF CUTTER. SELECT REPLY CODE 10AL18 AQGFD 05DIRECTION,HELIX,FLUTE FLUTE HELIX DIRECTION AN INDICATION OF THE DIRECTION OF THE FLUTE HELIX. SELECT REPLY CODE 10AA38 AQGGJ 10SIZE,BOLT BOLT SIZE DESIGNATES THE BOLT SIZE FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 AQGHA 10PITCH,DIAMETRAL DIAMETRAL PITCH THE NUMBER OF TEETH PER INCH OF PITCH DIAMETER. 1A MODE REPLY 0 AQGJB 10VOLTAGE IN VOLTS,TAP TAP VOLTAGE IN VOLTS THE TOTAL ELECTRICAL VOLTAGE OF THE TAP/S/ ON THE ITEM,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AQGKB 10CAPACITY,AMPERE HOUR AMPERE HOUR CAPACITY THE AMOUNT OF ELECTRICAL ENERGY THE ITEM IS RATED TO DELIVER. 1B MODE REPLY 0 AQGLB 10CAPACITY IN HOURS,TIME TIME CAPACITY IN HOURS THE SPECIFIED TIME AT WHICH THE CAPACITY OF THE ITEM IS RATED,EXPRESSED IN HOURS. 1B MODE REPLY 0 AQGMB 10TIME IN MINUTES,DISCHARGE DISCHARGE TIME IN MINUTES THE SPECIFIED TIME AT WHICH THE DISCHARGE OF THE ITEM IS RATED,EXPRESSED IN MINUTES. 1B MODE REPLY 0 AQGNB /D/ 10CAPACITY,AMPERE HOUR,LOW TEMP LOW TEMP AMPERE HOUR CAPACITY THE AMOUNT OF ELECTRICAL ENERGY THE ITEM IS RATED TO DELIVER AT A GIVEN LOW TEMPERATURE. 1B MODE REPLY 0 AQGPJ 10LIFE,SHELF,APPROXIMATE APPROXIMATE SHELF LIFE THE APPROXIMATE SHELF LIFE /STORAGE TIME/ OF THE ITEM. 1D AND 1B MODE REPLY12AH68 AQGQA 12QUANTITY,CELL CELL QUANTITY THE NUMBER OF CELLS CONTAINED IN THE ITEM. 1A MODE REPLY 0 AQGRD /D/ 09MATERIAL,PLATE PLATE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PLATE(S) IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH ISAC CODING TABLE 0326 IN PLACE OF OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 AQGSA 12QUANTITY PER CELL,PLATE PLATE QUANTITY PER CELL THE NUMBER OF PLATES IN A CELL. 1A MODE REPLY 0 AQGTD /D/ 07FEATURE,VENTILATION,FILLER CAP FILLER CAP VENTILATION FEATURE AN INDICATION OF WHETHER OR NOT A VENTILATION FEATURE IS INCLUDED ON THE FILLER CAP. SELECT REPLY CODE 10AA49 AQGWA /D/ 12QUANTITY PER TRAY,CELL CELL QUANTITY PER TRAY THE NUMBER OF CELLS PER TRAY. 1A MODE REPLY 0 AQGXJ 04HEIGHT,OVERALL,CELL CELL OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE CELL. 2D AND 1B MODE REPLY21AA051AC20 AQGYJ /D/ 04DEPTH,OVERALL,CELL CELL OVERALL DEPTH AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF A CELL,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AQGZJ /D/ 04LENGTH,OVERALL,CELL CELL OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CELL. 2D AND 1B MODE REPLY21AA051AC20 AQHAJ /D/ 04WIDTH,OVERALL,CELL CELL OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A CELL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AQHBJ 04DIAMETER,OVERALL,CELL CELL OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF THE CELL. 2D AND 1B MODE REPLY21AA051AC20 AQHCD 11METHOD,SERVICE SERVICE METHOD THE MEANS USED TO SERVICE THE ITEM. SELECT REPLY CODE 10AL06 AQHDD /D/ 07FEATURE,NONSPILLING NONSPILLING FEATURE AN INDICATION OF WHETHER OR NOT A NONSPILLING FEATURE IS INCLUDED. SELECT REPLY CODE 10AN31 AQHEB 10DISCHARGE RATE IN AMPS DISCHARGE RATE IN AMPS THE AMOUNT OF ELECTRICAL ENERGY THE ITEM IS RATED TO DISCHARGE,EXPRESSED IN AMPERES. 1B MODE REPLY 0 AQHFD /D/ 07INDICATOR,CHARGE CHARGE INDICATOR AN INDICATION OF WHETHER OR NOT A CHARGE INDICATOR IS INCLUDED. SELECT REPLY CODE 10AA49 AQHGD /D/ 07INDICATOR,LEVEL,ELECTROLYTE ELECTROLYTE LEVEL INDICATOR AN INDICATION OF WHETHER OR NOT AN ELECTROLYTE LEVEL INDICATOR IS INCLUDED. SELECT REPLY CODE 10AA49 AQHHD /D/ 19CONDITION,STORAGE/SHIPMENT STORAGE/SHIPMENT CONDITION THE CONDITION OF THE ITEM WHEN STORED AND/OR SHIPPED. PLEASE USE MRC CBBL IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AL09 AQHJD /D/ 07FACILITY,CHARGING,INTEGRAL INTEGRAL CHARGING FACILITY AN INDICATION OF WHETHER OR NOT AN INTEGRAL CHARGING FACILITY IS INCLUDED. SELECT REPLY CODE 10AA49 AQHKG 19AGENCY,CONTROLLING,COMPONENT COMPONENT CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION THAT CONTROLS THE COMPONENT. FULL TEXT WRITE-IN 0 AQHLG 19NAME,COMPONENT COMPONENT NAME THE NAME OF THE COMPONENT ASSIGNED BY THE CONTROLLING AGENCY. FULL TEXT WRITE-IN 0 AQHMJ A19NUMBER,IDENTIFYING,COMPONENT COMPONENT IDENTIFYING NUMBER THE SPECIFIC NUMBER USED TO IDENTIFY THE COMPONENT. 1D AND 1A MODE REPLY12AG99 AQHNA 12QUANTITY,PLATE,NEGATIVE NEGATIVE PLATE QUANTITY THE NUMBER OF NEGATIVE PLATES INCLUDED IN THE ITEM. 1A MODE REPLY 0 AQHPA 12QUANTITY,PLATE,POSITIVE POSITIVE PLATE QUANTITY THE NUMBER OF POSITIVE PLATES INCLUDED IN THE ITEM. 1A MODE REPLY 0 AQHQA 12QUANTITY,ACCOMMODATION,BATTERY JAR BATTERY JAR ACCOMMODATION QUANTITY THE NUMBER OF BATTERY JARS THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 AQHRA 12QUANTITY,ACCOMMODATION,BATTERY BATTERY ACCOMMODATION QUANTITY THE NUMBER OF BATTERIES THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 AQHSA 12QUANTITY,ACCOMMODATION,TRAY TRAY ACCOMMODATION QUANTITY THE NUMBER OF TRAYS THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 AQHTD /D/ 07COVER COVER AN INDICATION OF WHETHER OR NOT A COVER IS PROVIDED. SELECT REPLY CODE 10AB22 AQHWD 08LOCATION,SURFACE,CORRUGATED CORRUGATED SURFACE LOCATION INDICATES THE LOCATION OF THE CORRUGATED SURFACE ON THE ITEM. SELECT REPLY CODE 10AJ91 AQHXG 19PROCESSING,END END PROCESSING THE END PROCESSING,SUCH AS FLARED,THREADED,UNDERCUT,OR THE LIKE,ON THE ITEM. FULL TEXT WRITE-IN 0 AQHYG /D/ 04DIMENSION,PROCESSING,END END PROCESSING DIMENSION THE DIMENSION/S/,SUCH AS LENGTH,DIAMETER,DEGREES,OR THE LIKE,OF THE END PROCESSING. FULL TEXT WRITE-IN 0 AQHZJ 04LENGTH FROM BEND CENTER TO LONG LEG END LENGTH FROM BEND CENTER TO LONG LEG END THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS FROM THE CENTER OF THE BEND TO THE END OF THE LONG LEG. 2D AND 1B MODE REPLY21AA051AC20 AQJAG /D/ 19PROCESSING,END,LONG LEG LONG LEG END PROCESSING THE END PROCESSING ON THE LONG LEG,SUCH AS FLARED,THREADED,UNDERCUT,OR THE LIKE. FULL TEXT WRITE-IN 0 AQJBG /D/ 04DIMENSION,PROCESSING,LONG LEG LONG LEG PROCESSING DIMENSION THE DIMENSION/S/,SUCH AS LENGTH,DIAMETER,DEGREES,OR THE LIKE,OF THE LONG LEG PROCESSING. FULL TEXT WRITE-IN 0 AQJCJ 04LENGTH FROM BEND CENTER TO SHORT LEG END LENGTH FROM BEND CENTER TO SHORT LEG END THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS FROM THE CENTER OF THE BEND TO THE SHORT LEG END. 2D AND 1B MODE REPLY21AA051AC20 AQJDD 14SHAPE,FLOOR FLOOR SHAPE THE PHYSICAL CONFIGURATION OF THE FLOOR. SELECT REPLY CODE 10AD07 AQJEG 04LENGTH,SIDE,LATERAL LATERAL SIDE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A LATERAL SIDE OF AN ITEM,IN DISTINCTION FROM WIDTH. FULL TEXT WRITE-IN 0 AQJFJ 04HEIGHT,CENTER CENTER HEIGHT A MEASUREMENT FROM THE CENTER TO THE TOP OF AN ITEM,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AQJGJ 04HEIGHT,PEAK PEAK HEIGHT A MEASUREMENT FROM THE BASE TO THE PEAK OF AN ITEM,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AQJHJ 04HEIGHT,SIDEWALL SIDEWALL HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A SIDEWALL,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AQJJJ 04LENGTH,RIDGE RIDGE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A RIDGE OF AN ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AQJKG 19SECTION AND QUANTITY,TENT TENT SECTION AND QUANTITY THE SPECIFIC SECTION(S) OF THE TENT AND THE NUMBER REQUIRED. FULL TEXT WRITE-IN 0 AQJLD /D/ 09MATERIAL,FLOOR FLOOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FLOOR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH USE IF ISAC TABLE 0143 IN PLACE OF THIS CANCLED MRC. SELECT REPLY CODE 10AD09 AQJMA 19NUMBER,STOCK,NATIONAL,COMPONENT COMPONENT NATIONAL STOCK NUMBER THE NATIONAL STOCK NUMBER OF THE COMPONENT PART/S/ SUPPLIED WITH THE ITEM. 1A MODE REPLY 0 AQJND 19TENT FOR WHICH DESIGNED TENT FOR WHICH DESIGNED THE SPECIFIC TENT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL02 AQJPD 08LOCATION,MATERIAL,SCREENING SCREENING MATERIAL LOCATION INDICATES THE LOCATION OF THE ITEM TO WHICH SCREENING HAS BEEN APPLIED. SELECT REPLY CODE 10AJ91 AQJQD /D/ 09MATERIAL,SCREENING SCREENING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SCREENING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AQJRJ 04WIDTH,END END WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AQJSJ 04HEIGHT,END END HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE END,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AQJTG /D/ 03DESIGNATION,COMMERCIAL,MATERIAL MATERIAL COMMERCIAL DESIGNATION THE COMMERCIAL STANDARD IDENTIFICATION BY WHICH THE TYPE OR GRADE OF THE CLOTH IS KNOWN. FULL TEXT WRITE-IN 0 AQJWD 03DESIGNATION,POSITION POSITION DESIGNATION A DESIGNATION WHICH SERVES TO IDENTIFY THE POSITION OF THE ITEM. SELECT REPLY CODE 10AA38 AQJXJ 10TIME,RUNNING,MAXIMUM MAXIMUM RUNNING TIME THE MAXIMUM RUNNING TIME. 1D AND 1B MODE REPLY12AH68 AQJYD 08LOCATION,DEVICE,WINDING WINDING DEVICE LOCATION INDICATES THE LOCATION OF THE WINDING DEVICE ON THE ITEM. SELECT REPLY CODE 10AJ91 AQJZD /D/ 07CHARACTERISTIC,NONMAGNETIC NONMAGNETIC CHARACTERISTIC AN INDICATION OF WHETHER A NONMAGNETIC CHARACTERISTIC IS INCLUDED. IF INCLUDED, PLEASE USE MRC CBBL IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AQKAD 08LOCATION,DEVICE,REGULATING REGULATING DEVICE LOCATION INDICATES THE LOCATION OF THE REGULATION DEVICE ON THE ITEM. SELECT REPLY CODE 10AJ91 AQKBD 08LOCATION,DEVICE,RESETTING RESETTING DEVICE LOCATION INDICATES THE LOCATION OF THE RESETTING DEVICE ON THE ITEM. SELECT REPLY CODE 10AJ91 AQKCA 12QUANTITY,DIAL DIAL QUANTITY THE NUMBER OF DIALS PROVIDED. 1A MODE REPLY 0 AQKDB 10INCREMENT IN HOURS INCREMENT IN HOURS THE NUMBER OF INCREMENTS ON THE ITEM,EXPRESSED IN HOURS. 1B MODE REPLY 0 AQKED 18TYPE,POLE POLE TYPE INDICATES THE TYPE OF POLE. SELECT REPLY CODE 10AL08 AQKFJ 04LENGTH,PROJECTION,SPINDLE SPINDLE PROJECTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SPINDLE PROJECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AQKGD /D/ 07CLEAT CLEAT AN INDICATION OF WHETHER OR NOT CLEATS ARE INCLUDED. PLEASE USE MRC ABFF FOR ITEMS THAT HAD INCLUDED ANSWERED IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AQKHD /D/ 07HARDWARE HARDWARE AN INDICATION OF WHETHER OR NOT HARDWARE IS INCLUDED. PLEASE USE MRC ABFF FOR ITEMS THAT HAD INCLUDED ANSWERED IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AQKJD /D/ 07FEATURE,SPLICE,CENTER CUT CENTER CUT SPLICE FEATURE AN INDICATION OF WHETHER OR NOT A CENTER CUT SPLICE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AQKKG /D/ 11METHOD,FINISHING,END END FINISHING METHOD THE MEANS USED TO FINISH THE END(S). FULL TEXT WRITE-IN 0 AQKLD /D/ 19FEATURE,SECURING,GUY WIRE/ROPE GUY WIRE/ROPE SECURING FEATURE AN INDICATION OF THE SECURING FEATURE OF THE GUY WIRE AND/OR ROPE. SELECT REPLY CODE 10AL10 AQKMD /D/ 07FERRULE FERRULE AN INDICATION OF WHETHER OR NOT A FERRULE IS INCLUDED. SELECT REPLY CODE 10AA49 AQKND /D/ 07SIGNAL,INTERRUPTION,CURRENT CURRENT INTERRUPTION SIGNAL AN INDICATION OF WHETHER OR NOT A CURRENT INTERRUPTION SIGNAL IS INCLUDED. SELECT REPLY CODE 10AA49 AQKPD 18TYPE,HAND,SECOND SECOND HAND TYPE INDICATES THE TYPE OF SECOND HAND. SELECT REPLY CODE 10AL11 AQKQD 01COLOR,HAND,SECOND SECOND HAND COLOR THE HUE OR TINT OF THE SECOND HAND. SELECT REPLY CODE 10AD06 AQKRD 18TYPE,CASE,ORNAMENTAL ORNAMENTAL CASE TYPE INDICATES THE SPECIFIC TYPE OF ORNAMENTAL CASE PROVIDED. SELECT REPLY CODE 10AL12 AQKSD /D/ 18TYPE,BEZEL BEZEL TYPE INDICATES THE SPECIFIC TYPE OF BEZEL PROVIDED. PLEASE USE MRC BHMD IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB89 AQKTD /D/ 07MECHANISM,CHIME CHIME MECHANISM AN INDICATION OF WHETHER OR NOT A CHIME MECHANISM IS INCLUDED. SELECT REPLY CODE 10AA49 AQKWA /D/ 12QUANTITY,BELL BELL QUANTITY THE NUMBER OF BELLS PROVIDED. 1A MODE REPLY 0 AQKXD /D/ 03DESIGNATOR,CHIME CHIME DESIGNATOR A DESIGNATION BY WHICH THE CHIME IS KNOWN AND/OR IDENTIFIED. SELECT REPLY CODE 10AL13 AQKYD 18TYPE,UNIT,SOUND SOUND UNIT TYPE INDICATES THE TYPE OF SOUND UNIT PROVIDED. SELECT REPLY CODE 10AG89 AQKZD /D/ 07FEATURE,ENCASEMENT,INDIVIDUAL INDIVIDUAL ENCASEMENT FEATURE AN INDICATION OF WHETHER OR NOT AN INDIVIDUAL ENCASEMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AQLAD 18TYPE,PROJECTOR PROJECTOR TYPE INDICATES THE TYPE OF PROJECTOR INCLUDED. SELECT REPLY CODE 10AC46 AQLBA 12QUANTITY,PROJECTOR PROJECTOR QUANTITY THE NUMBER OF PROJECTORS PROVIDED. 1A MODE REPLY 0 AQLCJ 04DIAMETER,OUTSIDE,MAXIMUM,PROJECTOR FLARE PROJECTOR FLARE MAXIMUM OUTSIDE DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PROJECTOR FLARE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AQLDJ 04LENGTH,OVERALL,PROJECTOR PROJECTOR OVERALL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE PROJECTOR,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AQLFA 13THREAD SIZE,STUD STUD THREAD SIZE DESIGNATES THE STUD THREAD DIAMETER AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1A MODE REPLY 0 AQLGD 13THREAD SERIES,STUD STUD THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A STUD. SELECT REPLY CODE 10AH06 AQLHJ 04SIZE,CONNECTION,DISCHARGE DISCHARGE CONNECTION SIZE DESIGNATES THE SIZE OF THE DISCHARGE CONNECTION INCLUDED ON THE ITEM. 1D AND 1B MODE REPLY11AA05 AQLJD 13THREAD SERIES,CONNECTION,DISCHARGE DISCHARGE CONNECTION THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF THE DISCHARGE CONNECTION. SELECT REPLY CODE 10AH06 AQLKA 12QUANTITY,DIRECTION,SOUND SIGNAL SOUND SIGNAL DIRECTION QUANTITY THE NUMBER OF DIRECTIONS THE SOUND SIGNAL IS PROJECTED. 1A MODE REPLY 0 AQLLD /D/ 19CHARACTERISTIC,VALVE,MANUAL MANUAL VALVE CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC OF THE MANUAL VALVE. SELECT REPLY CODE 10AD15 AQLMD /D/ 08LOCATION,VALVE,MANUAL MANUAL VALVE LOCATION INDICATES THE LOCATION OF THE MANUAL VALVE ON THE ITEM. SELECT REPLY CODE 10AJ91 AQLND /D/ 18TYPE,VALVE,SOLENOID SOLENOID VALVE TYPE INDICATES THE TYPE OF SOLENOID VALVE PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AK38 AQLPD /D/ 07BODY,JACKETED,STEAM STEAM JACKETED BODY AN INDICATION OF WHETHER OR NOT A STEAM JACKETED BODY IS PROVIDED. SELECT REPLY CODE 10AB22 AQLQD /D/ 18TYPE,CURRENT,COMPRESSOR-MOTOR UNIT COMPRESSOR-MOTOR UNIT CURRENT TYPE INDICATES THE TYPE OF CURRENT WHICH OPERATES THE COMPRESSOR-MOTOR UNIT. SELECT REPLY CODE 10AB62 AQLRD 11METHOD,OPERATION,VALVE VALVE OPERATION METHOD THE MEANS USED TO CONTROL THE OPERATION OF THE VALVE. SELECT REPLY CODE 10AC58 AQLSD /D/ 07FEATURE,RESONANCE RESONANCE FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE IS INCLUDED TO CAUSE THE ITEM TO RESONATE. SELECT REPLY CODE 10AA49 AQLTD /D/ 07LIGHT LIGHT AN INDICATION OF WHETHER OR NOT A LIGHT IS PROVIDED. SELECT REPLY CODE 10AB22 AQLWD 08LOCATION,LIGHT LIGHT LOCATION INDICATES THE LOCATION OF THE LIGHT. SELECT REPLY CODE 10AJ91 AQLXD /D/ 07FACILITY,BRAKING BRAKING FACILITY AN INDICATION OF WHETHER OR NOT A BRAKING FACILITY/IES/ IS INCLUDED. SELECT REPLY CODE 10AA49 AQLYF T10RANGE IN DEG,CALIBRATION,ANGULAR ANGULAR CALIBRATION RANGE IN DEG THE ANGULAR CALIBRATION RANGE,EXPRESSED IN DEGREES. 1F MODE REPLY 0 AQLZJ 04LENGTH,OVERALL,DIAL DIAL OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE DIAL. 2D AND 1B MODE REPLY21AA051AC20 AQMAJ 04WIDTH,OVERALL,DIAL DIAL OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A DIAL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AQMBJ 04DIAMETER,OVERALL,DIAL DIAL OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE CENTER OF A CIRCULAR DIAL. 2D AND 1B MODE REPLY21AA051AC20 AQMCB 04ANGLE IN DEG,ARC ARC ANGLE IN DEG THE ANGLE OF THE ARC,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AQMDD 11METHOD,TRANSMISSION TRANSMISSION METHOD THE MEANS USED TO TRANSMIT. SELECT REPLY CODE 10AJ53 AQMED /D/ 09MATERIAL,SPECIFIC SPECIFIC MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SPECIFIC MATERIAL IS FABRICATED. SELECT REPLY CODE 10AD09 AQMFD /D/ 07CATALYST,SEPARATE SEPARATE CATALYST AN INDICATION OF WHETHER OR NOT A SEPARATE CATALYST IS INCLUDED. SELECT REPLY CODE 10AA49 AQMGD /D/ 07DYE,COLOR COLOR DYE AN INDICATION OF WHETHER OR NOT COLOR DYE IS INCLUDED. MRC IS DISCONTINUED AND REPLACED WITH MRC CBBL AND REPLY CODE FNP, DYE ON 03/28/2024. SELECT REPLY CODE 10AA49 AQMHD /D/ 07FEATURE,VULCANIZABLE,HEAT HEAT VULCANIZABLE FEATURE AN INDICATION OF WHETHER OR NOT A HEAT VULCANIZABLE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AQMJD /D/ 09MATERIAL,BASE,BITUMEN BITUMEN BASE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BITUMEN BASE IS FORMULATED. SELECT REPLY CODE 10AD09 AQMKD /D/ 07FILLER FILLER AN INDICATION AS TO WHETHER OR NOT A FILLER IS INCLUDED. SELECT REPLY CODE 10AA49 AQMLD /D/ 07FILLER,ASBESTOS ASBESTOS FILLER AN INDICATION OF WHETHER OR NOT AN ASBESTOS FILLER IS INCLUDED. SELECT REPLY CODE 10AA49 AQMMD 18TYPE,PIGMENT PIGMENT TYPE INDICATES THE PARTICULAR TYPE OF PIGMENT UTILIZED IN THE ITEM. SELECT REPLY CODE 10AF53 AQMNB 10PERCENTAGE,CONTENT,SOLID SOLID CONTENT PERCENTAGE THE PERCENTAGE OF SOLID CONTENT CONTAINED IN THE ITEM. 1B MODE REPLY 0 AQMPJ /D/ 10PENETRATION RATE AT 77 DEG FAHRENHEIT,MATERIAL,ASPHALT BASE ASPHALT BASE MATERIAL PENETRATION RATE AT 77 DEG FAHRENHEIT THE RATED PENETRATION OF ASPHALT BASE MATERIAL AT 77 DEGREES FAHRENHEIT. 2D AND 1B MODE REPLY21AA051AC20 AQMQD /D/ 07ACCELERATOR,SEPARATE SEPARATE ACCELERATOR AN INDICATION OF WHETHER OR NOT A SEPARATE ACCELERATOR IS INCLUDED. SELECT REPLY CODE 10AA49 AQMRG /D/ 19PROCESSING,END,SHORT LEG SHORT LEG END PROCESSING THE END PROCESSING ON THE SHORT LEG,SUCH AS FLARED,THREADED UNDERCUT,OR THE LIKE. FULL TEXT WRITE-IN 0 AQMSG /D/ 04DIMENSION,PROCESSING,SHORT LEG SHORT LEG PROCESSING DIMENSION THE DIMENSION/S/,SUCH AS LENGTH,DIAMETER,DEGREES,OR THE LIKE,OF THE SHORT LEG PROCESSING. FULL TEXT WRITE-IN 0 AQMTJ 04DIAMETER,HOLE,VENT VENT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE VENT HOLE, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AQMWJ 04LENGTH,EDGE,CUTTING CUTTING EDGE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CUTTING EDGE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AQMXJ 04LENGTH,BLADE,LONGEST LONGEST BLADE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE LONGEST BLADE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AQMYA /D/ 12QUANTITY,BLADE,SERRATED SERRATED BLADE QUANTITY THE NUMBER OF SERRATED BLADES ON THE ITEM. 1A MODE REPLY 0 AQMZD /D/ 07DETACHABILITY,EDGE,BLADE BLADE EDGE DETACHABILITY AN INDICATION OF WHETHER OR NOT THE BLADE EDGE(S) IS DETACHABLE. SELECT REPLY CODE 10AH97 AQNAD 18TYPE,GRIP GRIP TYPE INDICATES THE TYPE OF GRIP ON THE ITEM. SELECT REPLY CODE 10AL17 AQNBD 07DETACHABILITY,HANDLE HANDLE DETACHABILITY AN INDICATION OF WHETHER OR NOT THE HANDLE IS DETACHABLE. SELECT REPLY CODE 10AH97 AQNCD /D/ 07SPRING,HANDLE HANDLE SPRING AN INDICATION OF WHETHER OR NOT A HANDLE SPRING IS INCLUDED. SELECT REPLY CODE 10AA49 AQNDD /D/ 08LOCATION,DEVICE,LOCKING LOCKING DEVICE LOCATION INDICATES THE LOCATION OF THE LOCKING DEVICE ON THE ITEM. SELECT REPLY CODE 10AJ91 AQNED 18TYPE,JOINT JOINT TYPE INDICATES THE TYPE OF JOINT/S/ ON THE ITEM. SELECT REPLY CODE 10AL19 AQNFD /D/ 19FLEXIBILITY,SHAFT SHAFT FLEXIBILITY AN INDICATION OF THE FLEXIBILITY OF THE SHAFT. SELECT REPLY CODE 10AD03 AQNGD 18TYPE,SYRINGE SYRINGE TYPE INDICATES THE TYPE OF SYRINGE. SELECT REPLY CODE 10AG24 AQNHB 10CAPACITY IN OUNCES,FLUID FLUID CAPACITY IN OUNCES THE AMOUNT OF FLUID THE ITEM IS DESIGNED TO HOLD,EXPRESSED IN OUNCES. 1B MODE REPLY 0 AQNJJ 04DIAMETER,END,NOZZLE,TUBE TUBE NOZZLE END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBE AT THE NOZZLE END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AQNKD 19FLEXIBILITY,TUBE TUBE FLEXIBILITY AN INDICATION OF THE FLEXIBILITY OF THE TUBE. SELECT REPLY CODE 10AD03 AQNLD /D/ 09MATERIAL,STRINGER STRINGER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE STRINGER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AQNMJ 10WEIGHT,NOMINAL NOMINAL WEIGHT A RELATIVE NOMINAL MEASURE OF THE MASS OF AN ITEM WITH RESPECT TO ITS DENSITY. 1D AND 1B MODE REPLY12AB16 AQNND 18TYPE,ADAPTER ADAPTER TYPE INDICATES THE TYPE OF ADAPTER PROVIDED. SELECT REPLY CODE 10AL20 AQNPA 19NUMBER,MODEL,ADAPTER ADAPTER MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE ADAPTER. 1A MODE REPLY 0 AQNQA 19NUMBER,MODEL,INDIVIDUAL BOMB FUZE INDIVIDUAL BOMB FUZE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE INDIVIDUAL BOMB FUZE. 1A MODE REPLY 0 AQNRA 12QUANTITY,BOMB BOMB QUANTITY THE NUMBER OF BOMBS INCLUDED. 1A MODE REPLY 0 AQNSJ 10WEIGHT,NOMINAL,INDIVIDUAL BOMB INDIVIDUAL BOMB NOMINAL WEIGHT THE RELATIVE NOMINAL MEASURE OF THE MASS OF AN INDIVIDUAL BOMB WITH RESPECT TO ITS DENSITY. 1D AND 1B MODE REPLY12AB16 AQNTD 19CONTENT,BOMB,INDIVIDUAL INDIVIDUAL BOMB CONTENT AN INDICATION OF THE CONTENT OF THE INDIVIDUAL BOMB. SELECT REPLY CODE 10AL22 AQNWD 09MATERIAL,FILLER,EXPLOSIVE EXPLOSIVE FILLER MATERIAL THE TYPE OF EXPLOSIVE FILLER CONTAINED WITHIN THE ITEM. SELECT REPLY CODE 10AF45 AQNXD 09MATERIAL,FILLER,INDIVIDUAL BOMB INDIVIDUAL BOMB FILLER MATERIAL THE FILLER MATERIAL CONTAINED WITHIN EACH INDIVIDUAL BOMB. SELECT REPLY CODE 10AF45 AQNYA 19SYMBOL,FILLER,CHEMICAL CORPS,INDIVIDUAL BOMB INDIVIDUAL BOMB CHEMICAL CORPS FILLER SYMBOL THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE IDENTIFYING SYMBOL ASSIGNED BY THE CHEMICAL CORPS. 1A MODE REPLY 0 AQNZD 18TYPE,STABILIZER,BOMB,INDIVIDUAL INDIVIDUAL BOMB STABILIZER TYPE INDICATES THE TYPE OF STABILIZER PROVIDED IN AN INDIVIDUAL BOMB. SELECT REPLY CODE 10AJ77 AQPAD /D/ 07FUZE,BOMB,INDIVIDUAL INDIVIDUAL BOMB FUZE AN INDICATION OF WHETHER OR NOT AN INDIVIDUAL BOMB FUZE IS INCLUDED. SELECT REPLY CODE 10AA49 AQPBD /D/ 07FEATURE,INSTALLATION,FUZE FUZE INSTALLATION FEATURE AN INDICATION OF WHETHER OR NOT THE FUZE IS INSTALLED. SELECT REPLY CODE 10AL24 AQPCD 18TYPE,FUZE,INDIVIDUAL BOMB INDIVIDUAL BOMB FUZE TYPE INDICATES THE PARTICULAR TYPE OF FUZE INCLUDED WITH THE INDIVIDUAL BOMB. SELECT REPLY CODE 10AF46 AQPDD 19CONTENT,FUZE FUZE CONTENT AN INDICATION OF THE CONTENT OF THE FUZE. SELECT REPLY CODE 10AL22 AQPEA 19NUMBER,MODEL,INDIVIDUAL BOMB INDIVIDUAL BOMB MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE INDIVIDUAL BOMB. 1A MODE REPLY 0 AQPFD 19CONTENT,ITEM ITEM CONTENT AN INDICATION OF THE CONTENT OF THE ITEM. SELECT REPLY CODE 10AL22 AQPGA 19SYMBOL,FILLER,CHEMICAL CORPS CHEMICAL CORPS FILLER SYMBOL THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED FILLER SYMBOL BY THE CHEMICAL CORPS. 1A MODE REPLY 0 AQPHB /D/ 10DURATION IN SECONDS,FLASH FLASH DURATION IN SECONDS A MEASUREMENT OF THE ELAPSED TIME OF THE FLASH,EXPRESSED IN SECONDS. 1B MODE REPLY 0 AQPJG /D/ 10CANDLEPOWER,NOMINAL,FLASH FLASH NOMINAL CANDLEPOWER THE NOMINAL CANDLEPOWER,OR MEASUREMENT OF LUMINOUS INTENSITY,OF THE FLASH. FULL TEXT WRITE-IN 0 AQPKD /D/ 07CHARGE,FIRE,FIRST FIRST FIRE CHARGE AN INDICATION OF WHETHER OR NOT A FIRST FIRE CHARGE IS INCLUDED. SELECT REPLY CODE 10AA49 AQPLJ 04WIDTH,FACE FACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AQPMJ 04LENGTH,CUT CUT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CUTTING PORTION OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 AQPNA 13THREAD SIZE,HOLE,MOUNTING MOUNTING HOLE THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A MOUNTING HOLE. 1A MODE REPLY 0 AQPPD 18TYPE,SHANK SHANK TYPE INDICATES THE TYPE OF SHANK. SELECT REPLY CODE 10AH09 AQPQA 19NUMBER,TAPER,SHANK SHANK TAPER NUMBER AN INDICATION OF THE NUMBER OF THE SHANK TAPER. 1A MODE REPLY 0 AQPRJ /D/ 10INCREMENT,LUMINOUS,SMALLEST SMALLEST LUMINOUS INCREMENT THE SMALLEST INCREMENT DESIGNATED BY THE LUMINOUS GRADUATION. 1D AND 1B MODE REPLY12AJ20 AQPSD 01COLOR,GRADUATION,MAJOR MAJOR GRADUATION COLOR THE HUE OR TINT OF THE MAJOR GRADUATION. SELECT REPLY CODE 10AD06 AQPTD 01COLOR,GRADUATION,MINOR MINOR GRADUATION COLOR THE HUE OR TINT OF THE MINOR GRADUATION. SELECT REPLY CODE 10AD06 AQPWD /D/ 07NUMERAL,LUMINOUS LUMINOUS NUMERAL AN INDICATION OF WHETHER OR NOT A LUMINOUS NUMERAL/S/ IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AQPXG 03DESIGNATION,COLOR,INSCRIPTION INSCRIPTION COLOR DESIGNATION THE DESIGNATION OF THAT PORTION OF AN ITEM TO WHICH THE COLOR IS APPLIED. FULL TEXT WRITE-IN 0 AQPYD /D/ 07DIAL,TOTALIZER,SEPARATE SEPARATE TOTALIZER DIAL AN INDICATION OF WHETHER OR NOT A SEPARATE TOTALIZER DIAL IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AQPZF T10RANGE IN MINUTES,DIAL,TOTALIZER TOTALIZER DIAL RANGE IN MINUTES THE RANGE AT WHICH THE TOTALIZER DIAL WILL TOTAL TIME,EXPRESSED IN MINUTES. 1F MODE REPLY 0 AQQAD /D/ 07DIAL,LUMINOUS LUMINOUS DIAL AN INDICATION OF WHETHER OR NOT A LUMINOUS DIAL IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AQQBD 11METHOD,ILLUMINATIVE ILLUMINATIVE METHOD THE MEANS OF PRODUCING ILLUMINATION. SELECT REPLY CODE 10AL21 AQQCA 03DESIGNATION,CUTTER,RANGE RANGE CUTTER DESIGNATION THE INDUSTRIAL DESIGNATOR OR TERM USED TO IDENTIFY THE ITEM. 1A MODE REPLY 0 AQQDA 12QUANTITY,TOOTH,SINGLE CUTTER SINGLE CUTTER TOOTH QUANTITY THE NUMBER OF TEETH ON A SINGLE CUTTER. 1A MODE REPLY 0 AQQEA 03DESIGNATION,CUTTER CUTTER DESIGNATION THE INDUSTRIAL DESIGNATOR OR TERM USED TO IDENTIFY THE ITEM. 1A MODE REPLY 0 AQQFD 08LOCATION,MATERIAL MATERIAL LOCATION INDICATES THE LOCATION OF THE ITEM TO WHICH A SPECIFIC MATERIAL IS APPLICABLE. SELECT REPLY CODE 10AJ91 AQQGD 18TYPE,TOOTH TOOTH TYPE INDICATES THE TYPE OF TEETH PROVIDED. SELECT REPLY CODE 10AL23 AQQHD 19ARRANGEMENT,TOOTH TOOTH ARRANGEMENT THE TERMINOLOGY USED TO INDICATE THE ARRANGEMENT OF THE TEETH. SELECT REPLY CODE 10AK87 AQQJD 14SHAPE,CUT CUT SHAPE THE PHYSICAL CONFIGURATION OF THE CUT. SELECT REPLY CODE 10AD07 AQQKD 03DESIGNATION,SIDE,CUTTING CUTTING SIDE DESIGNATION THE DESIGNATION INDICATING THE CUTTING SIDE. SELECT REPLY CODE 10AA38 AQQLD 05DIRECTION,HELIX HELIX DIRECTION AN INDICATION OF THE HELIX DIRECTION. SELECT REPLY CODE 10AA38 AQQMD /D/ 07FEATURE,CLEARANCE,SIDE CHIP SIDE CHIP CLEARANCE FEATURE AN INDICATION OF WHETHER OR NOT A SIDE CHIP CLEARANCE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AQQND /D/ 18TYPE FOR WHICH DESIGNED,MATERIAL MATERIAL TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF MATERIAL FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AD93 AQQPH /D/ 19FINISH AND LOCATION,BODY BODY FINISH AND LOCATION AN INDICATION OF THE BODY FINISH AND ITS LOCATION. 2D MODE REPLY 22AA413AJ91 AQQQD 19FINISH,EDGE,CUTTING CUTTING EDGE FINISH AN INDICATION OF THE FINISH OF THE CUTTING EDGE. SELECT REPLY CODE 10AA41 AQQRD 18TYPE,EDGE EDGE TYPE INDICATES THE TYPE OF EDGE ON THE ITEM. SELECT REPLY CODE 10AL25 AQQSD 05DIRECTION,CUT CUT DIRECTION AN INDICATION OF THE CUT DIRECTION. SELECT REPLY CODE 10AA38 AQQTD /D/ 09MATERIAL,TIP TIP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TIP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AQQWA 12QUANTITY,HAND,SWEEP SWEEP HAND QUANTITY THE NUMBER OF SWEEP HANDS PROVIDED. 1A MODE REPLY 0 AQQXA 12QUANTITY,HAND HAND QUANTITY THE NUMBER OF HANDS PROVIDED. 1A MODE REPLY 0 AQQYD 03DESIGNATION,HAND HAND DESIGNATION THE DESIGNATION USED TO IDENTIFY THE HAND. SELECT REPLY CODE 10AL26 AQQZD 18TYPE,HAND HAND TYPE INDICATES THE TYPE OF HAND PROVIDED. SELECT REPLY CODE 10AL11 AQRAD 01COLOR,HAND HAND COLOR THE HUE OR TINT OF THE HAND. SELECT REPLY CODE 10AD06 AQRBD /D/ 07HAND,LUMINOUS LUMINOUS HAND AN INDICATION OF WHETHER OR NOT A LUMINOUS HAND IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AQRCA 12QUANTITY,JEWEL JEWEL QUANTITY THE NUMBER OF JEWELS PROVIDED. 1A MODE REPLY 0 AQRDD 03DESIGNATION,SIZE,MOVEMENT MOVEMENT SIZE DESIGNATION THE DESIGNATION BY WHICH THE SIZE OF THE MOVEMENT IS IDENTIFIED. SELECT REPLY CODE 10AF81 AQRED 11METHOD,WINDING WINDING METHOD THE MEANS BY WHICH THE ITEM IS WOUND. SELECT REPLY CODE 10AL27 AQRFA /D/ 19NUMBER,MODEL,FIRST FIRE CHARGE FIRST FIRE CHARGE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE FIRST FIRE CHARGE. 1A MODE REPLY 0 AQRGD /D/ 07FEATURE,CHARGE,SPOTTING,SPECIFIC SPECIFIC SPOTTING CHARGE FEATURE AN INDICATION OF WHETHER OR NOT A SPECIFIC SPOTTING CHARGE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AQRHA 19NUMBER,MODEL,SPOTTING CHARGE SPOTTING CHARGE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE SPOTTING CHARGE. 1A MODE REPLY 0 AQRJD 18TYPE,STABILIZER STABILIZER TYPE INDICATES THE TYPE OF STABILIZER INCLUDED ON THE ITEM. SELECT REPLY CODE 10AJ77 AQRKD /D/ 07LUG,SUSPENSION SUSPENSION LUG AN INDICATION OF WHETHER OR NOT A SUSPENSION LUG IS INCLUDED. SELECT REPLY CODE 10AA49 AQRLD /D/ 18TYPE,GAGE GAGE TYPE INDICATES THE TYPE OF GAGE PROVIDED ON THE ITEM. PLEASE USE MRC CBBL IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AJ89 AQRMD /D/ 07FEATURE,ASSEMBLED,WAFER WAFER ASSEMBLED FEATURE AN INDICATION OF WHETHER OR NOT A WAFER ASSEMBLED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AQRNA /D/ 12QUANTITY PER WAFER,BOMB BOMB QUANTITY PER WAFER THE NUMBER OF BOMBS IN EACH WAFER. 1A MODE REPLY 0 AQRPJ 10WEIGHT,MATERIAL,FILLER FILLER MATERIAL WEIGHT A RELATIVE MEASURE OF THE MASS OF THE FILLER MATERIAL WITH RESPECT TO ITS DENSITY. 1D AND 1B MODE REPLY12AB16 AQRQD /D/ 07PLUMBING PLUMBING AN INDICATION OF WHETHER OR NOT PLUMBING IS INCLUDED. SELECT REPLY CODE 10AA49 AQRRD /D/ 07HARNESS HARNESS AN INDICATION OF WHETHER OR NOT A HARNESS IS INCLUDED. SELECT REPLY CODE 10AA49 AQRSA 19NUMBER,MODEL,HARNESS HARNESS MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE HARNESS. 1A MODE REPLY 0 AQRTD /D/ 07FEATURE,INSTALLATION,FIN ASSEMBLY FIN ASSEMBLY INSTALLATION FEATURE AN INDICATION OF WHETHER OR NOT THE FIN ASSEMBLY IS INSTALLED. SELECT REPLY CODE 10AL24 AQRWD /D/ 17SURFACE TREATMENT,CONDUCTOR CONDUCTOR SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE CONDUCTOR. SELECT REPLY CODE 10AD09 AQRXJ 04DIAMETER,OUTSIDE,TUBING TUBING OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBING,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AQRYJ 04DIAMETER,INSIDE,TUBING TUBING INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBING,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AQRZJ 04DISTANCE BETWEEN CONDUCTORS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN CONDUCTORS THE DISTANCE BETWEEN THE CENTERLINES OF THE CONDUCTORS. 2D AND 1B MODE REPLY21AA051AC20 AQSAD /D/ 07ASSEMBLY,WIRE,ARMING ARMING WIRE ASSEMBLY AN INDICATION OF WHETHER OR NOT AN ARMING WIRE ASSEMBLY IS INCLUDED. SELECT REPLY CODE 10AA49 AQSBA 12QUANTITY,ASSEMBLY,ARMING WIRE ARMING WIRE ASSEMBLY QUANTITY THE NUMBER OF ARMING WIRE ASSEMBLIES IN THE ITEM. 1A MODE REPLY 0 AQSCA 19NUMBER,MODEL,ARMING WIRE ASSEMBLY ARMING WIRE ASSEMBLY MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE ARMING WIRE ASSEMBLY. 1A MODE REPLY 0 AQSDD /D/ 07ADAPTER,IGNITER IGNITER ADAPTER AN INDICATION OF WHETHER OR NOT AN IGNITER ADAPTER IS INCLUDED. SELECT REPLY CODE 10AA49 AQSEA 12QUANTITY ACCOMMODATED,BOMB BOMB QUANTITY ACCOMMODATED THE NUMBER OF BOMBS ACCOMMODATED BY THE ITEM. 1A MODE REPLY 0 AQSFJ 10WEIGHT FOR WHICH DESIGNED,BOMB BOMB WEIGHT FOR WHICH DESIGNED A RELATIVE MEASURE OF THE MASS OF THE BOMB WITH RESPECT TO ITS DENSITY,FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY12AB16 AQSGD /D/ 07FLANGE,MOUNTING MOUNTING FLANGE AN INDICATION OF WHETHER OR NOT A MOUNTING FLANGE IS INCLUDED. SELECT REPLY CODE 10AA49 AQSHD /D/ 07HOLE,DRILLED,LOCKING PIN LOCKING PIN DRILLED HOLE AN INDICATION OF WHETHER OR NOT A DRILLED HOLE/S/ IS PROVIDED FOR A LOCKING PIN/S/. SELECT REPLY CODE 10AB22 AQSJD /D/ 09MATERIAL,WIRE WIRE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WIRE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AQSKA 12QUANTITY,BRANCH,WIRE WIRE BRANCH QUANTITY THE NUMBER OF BRANCHES CONTAINED IN THE WIRE. 1A MODE REPLY 0 AQSLJ 04LENGTH,BRANCH BRANCH LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A BRANCH,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AQSMA 12QUANTITY,CLIP,SAFETY SAFETY CLIP QUANTITY THE NUMBER OF SAFETY CLIPS CONTAINED IN THE ITEM. 1A MODE REPLY 0 AQSND /D/ 09MATERIAL,WIRE,SWIVEL LOOP SWIVEL LOOP WIRE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SWIVEL LOOP WIRE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AQSPJ 04DIAMETER,WIRE,SWIVEL LOOP SWIVEL LOOP WIRE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SWIVEL LOOP WIRE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AQSQA 13THREAD SIZE,END,FIRST FIRST END THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER INCH OF THE FIRST END. 1A MODE REPLY 0 AQSRD 13THREAD SERIES/TYPE DESIGNATOR,END,FIRST FIRST END THREAD SERIES/TYPE DESIGNATOR DESIGNATES THE SERIES/TYPE OF THE THREADS OF THE FIRST END. SELECT REPLY CODE 10AH06 AQSSA 13THREAD SIZE,END,SECOND SECOND END THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER INCH OF THE SECOND END. 1A MODE REPLY 0 AQSTD 13THREAD SERIES/TYPE DESIGNATOR,END,SECOND SECOND END THREAD SERIES/TYPE DESIGNATOR DESIGNATES THE SERIES/TYPE OF THE THREADS OF THE SECOND END. SELECT REPLY CODE 10AH06 AQSWD /D/ 07END,UNION UNION END AN INDICATION OF WHETHER OR NOT A UNION END IS INCLUDED. SELECT REPLY CODE 10AA49 AQSXD /D/ 07FACILITY,WRENCHING WRENCHING FACILITY AN INDICATION OF WHETHER OR NOT A WRENCHING FACILITY IS INCLUDED. SELECT REPLY CODE 10AA49 AQSYD /D/ 07FEATURE,SHATTERPROOF SHATTERPROOF FEATURE AN INDICATION OF WHETHER OR NOT A SHATTERPROOF FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AQSZA /D/ 16STYLE DESIGNATOR,CYLINDER CYLINDER STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CYLINDER. 1A MODE REPLY 0 AQTAD /D/ 07FEATURE,SHOCKPROOF SHOCKPROOF FEATURE AN INDICATION OF WHETHER OR NOT A SHOCKPROOF FEATURE IS PROVIDED. IF PROVIDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB22 AQTBD /D/ 07MECHANISM,STRIKING STRIKING MECHANISM AN INDICATION OF WHETHER OR NOT A STRIKING MECHANISM IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AQTCD /D/ 07INDICATOR,DATE,CIVIL CIVIL DATE INDICATOR AN INDICATION OF WHETHER OR NOT A CIVIL DATE INDICATOR IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AQTDD 18TYPE,RESET,CORRECT TIME CORRECT TIME RESET TYPE INDICATES THE TYPE OF CORRECT TIME RESET. SELECT REPLY CODE 10AC58 AQTED /D/ 07FEATURE,STOPWATCH STOPWATCH FEATURE AN INDICATION OF WHETHER OR NOT A STOPWATCH FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AQTFD /D/ 07FEATURE,SETTING,SECOND SECOND SETTING FEATURE AN INDICATION OF WHETHER OR NOT A SECOND SETTING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AQTGD 11METHOD,CONTROL CONTROL METHOD THE MEANS BY WHICH THE ITEM IS CONTROLLED. SELECT REPLY CODE 10AL28 AQTHD 18TYPE,KNOB KNOB TYPE INDICATES THE SPECIFIC TYPE OF KNOB PROVIDED. SELECT REPLY CODE 10AL29 AQTJD 18TYPE,REAMER REAMER TYPE INDICATES THE SPECIFIC TYPE OF REAMER PROVIDED. SELECT REPLY CODE 10AL35 AQTKD 08LOCATION,KNOB KNOB LOCATION INDICATES THE SPECIFIC LOCATION OF THE KNOB. SELECT REPLY CODE 10AJ91 AQTLD /D/ 09MATERIAL,TOE TOE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TOE IS FABRICATED. SELECT REPLY CODE 10AD09 AQTMD 01COLOR,CASE,PLASTIC PLASTIC CASE COLOR THE HUE OR TINT OF THE PLASTIC CASE. SELECT REPLY CODE 10AD06 AQTND 18TYPE,CRYSTAL CRYSTAL TYPE INDICATES THE SPECIFIC TYPE OF CRYSTAL PROVIDED. SELECT REPLY CODE 10AL32 AQTPB 10PRESSURE IN PSI,TEST,MAXIMUM MAXIMUM TEST PRESSURE IN PSI THE MAXIMUM TEST PRESSURE USED TO QUALIFY THE ITEM,EXPRESSED IN POUNDS PER SQUARE INCH. 1B MODE REPLY 0 AQTQD /D/ 07CAP,STEM STEM CAP AN INDICATION OF WHETHER OR NOT A STEM CAP IS PROVIDED. SELECT REPLY CODE 10AB22 AQTRD 18TYPE,TIME TIME TYPE INDICATES THE TYPE OF TIME. SELECT REPLY CODE 10AK74 AQTSD /D/ 07CASE,MOUNTING MOUNTING CASE AN INDICATION OF WHETHER OF NOT A MOUNTING CASE IS INCLUDED. SELECT REPLY CODE 10AA49 AQTTD /D/ 18TYPE,TRIM TRIM TYPE INDICATES THE TYPE OF TRIM ON THE ITEM. SELECT REPLY CODE 10AL33 AQTWJ 04WIDTH,BOTTOM BOTTOM WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BOTTOM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AQTXD /D/ 18TYPE,CONSTRUCTION,HEEL/SOLE HEEL/SOLE CONSTRUCTION TYPE INDICATES THE CONSTRUCTION TYPE OF THE HEEL AND SOLE. SELECT REPLY CODE 10AC66 AQTYD /D/ 11METHOD,ATTACHMENT,HEEL/SOLE HEEL/SOLE ATTACHMENT METHOD THE MEANS USED TO ATTACH THE HEEL AND SOLE TO THE ITEM. SELECT REPLY CODE 10AB47 AQTZD /D/ 11METHOD,ASSEMBLY,SOLE/TOE SOLE/TOE ASSEMBLY METHOD THE MEANS BY WHICH THE SOLE AND TOE ARE ASSEMBLED. SELECT REPLY CODE 10AB47 AQWAD /D/ 18TYPE,INSOLE INSOLE TYPE INDICATES THE TYPE OF INSOLE PROVIDED IN THE ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AL34 AQWBD /D/ 07LOOP,PULL ON PULL ON LOOP AN INDICATION OF WHETHER OR NOT PULL ON LOOPS ARE INCLUDED. SELECT REPLY CODE 10AA49 AQWCD /D/ 07SHELF,STRAP,SKI SKI STRAP SHELF AN INDICATION OF WHETHER OR NOT SKI STRAP SHELVES ARE INCLUDED. SELECT REPLY CODE 10AA49 AQWDD /D/ 07TAG,INSTRUCTION INSTRUCTION TAG AN INDICATION OF WHETHER OR NOT AN INSTRUCTION TAG IS INCLUDED. SELECT REPLY CODE 10AA49 AQWED /D/ 18TYPE,SOLE SOLE TYPE INDICATES THE TYPE OF SOLE PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AD03 AQWFJ A03DESIGNATOR,SIZE,SOCKET TAPER SOCKET TAPER SIZE DESIGNATOR THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE SOCKET TAPER SIZE. 1D AND 1A MODE REPLY12AH09 AQWGD 02DESIGN,FLUTE FLUTE DESIGN THE DESIGN OF THE FLUTES. SELECT REPLY CODE 10AD07 AQWHD 18TYPE,FLUTE FLUTE TYPE INDICATES THE TYPE OF FLUTE PROVIDED. SELECT REPLY CODE 10AL23 AQWJD 05DIRECTION,CUT,FLUTE FLUTE CUT DIRECTION AN INDICATION OF THE DIRECTION OF THE FLUTE CUT. SELECT REPLY CODE 10AA38 AQWKD /D/ 09MATERIAL,TIP,CUTTING EDGE CUTTING EDGE TIP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CUTTING EDGE TIPS ARE FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AQWLD 18TYPE,PILOT PILOT TYPE INDICATES THE TYPE OF PILOT PROVIDED. SELECT REPLY CODE 10AE90 AQWMD /D/ 07GUIDE GUIDE AN INDICATION OF WHETHER OR NOT A GUIDE IS INCLUDED. PLEASE USE MRC ABFF FOR NIINS WERE ANSWERD WITH "INCLUDED" IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AQWNJ 04DIAMETER,GUIDE GUIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GUIDE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AQWPJ 04LENGTH,GUIDE GUIDE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE GUIDE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AQWQD 18TYPE,CHANGEABILITY,SIZE SIZE CHANGEABILITY TYPE INDICATES THE TYPE OF SIZE CHANGEABILITY PROVIDED. SELECT REPLY CODE 10AL36 AQWRJ T10RANGE,SIZE SIZE RANGE DESIGNATES THE MINIMUM AND MAXIMUM SIZE. 1D AND 1F MODE REPLY11AA05 AQWSD 14SHAPE,HOLE,ARBOR ARBOR HOLE SHAPE THE PHYSICAL CONFIGURATION OF THE ARBOR HOLE. SELECT REPLY CODE 10AD07 AQWTD /D/ 07KEYWAY KEYWAY AN INDICATION OF WHETHER OR NOT A KEYWAY IS INCLUDED. SELECT REPLY CODE 10AA49 AQWWA /D/ 19NUMBER/D/,IDENTIFYING,INTERSTATE COMMERCE COMMISSION INTERSTATE COMMERCE COMMISSION IDENTIFYING NUMBER/D A NUMBER ASSIGNED TO THE ITEM BY THE INTERSTATE COMMERCE COMMISSION FOR PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 AQWXD 19CODE,COLOR,PART A PART A COLOR CODE THE APPLICATION OF A COLOR OR SERIES OF COLORS TO A SPECIFIC PORTION OF AN ITEM FOR THE EXPRESSED PURPOSE OF DESCRIBING AND/OR IDENTIFYING THE FUNCTIONAL DESIGN OR THE SYSTEM APPLICATION. SELECT REPLY CODE 10AD06 AQWYD 19CODE,COLOR,PART B PART B COLOR CODE THE APPLICATION OF A COLOR OR A SERIES OF COLORS TO A SPECIFIC PORTION OF AN ITEM FOR THE EXPRESSED PURPOSE OF DESCRIBING AND/OR IDENTIFYING THE FUNCTIONAL DESIGN OR THE SYSTEM APPLICATION. SELECT REPLY CODE 10AD06 AQWZD 19CODE,COLOR,PART C PART C COLOR CODE THE APPLICATION OF A COLOR OR A SERIES OF COLORS TO A SPECIFIC PORTION OF AN ITEM FOR THE EXPRESSED PURPOSE OF DESCRIBING AND/OR IDENTIFYING THE FUNCTIONAL DESIGN OR THE SYSTEM APPLICATION. SELECT REPLY CODE 10AD06 AQXAD 19CODE,COLOR,BODY BODY COLOR CODE THE APPLICATION OF A COLOR OR A SERIES OF COLORS TO THE BODY OF AN ITEM FOR THE EXPRESSED PURPOSE OF DESCRIBING AND/OR IDENTIFYING THE FUNCTIONAL DESIGN OR THE SYSTEM APPLICATION. SELECT REPLY CODE 10AD06 AQXBD 18TYPE,GAS,COLOR CODED COLOR CODED GAS TYPE INDICATES THE TYPE OF GAS CONTAINED IN A COLOR CODED CYLINDER. SELECT REPLY CODE 10AB75 AQXCJ /D/ 10CAPACITY RATING CAPACITY RATING A MEASUREMENT OF THE CAPACITY OF AN ITEM. PLEASE USE MRC BBLT IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AB101AC20 AQXDD 13THREAD LOCATION,NECK NECK THREAD LOCATION INDICATES THE LOCATION OF THE THREAD ON THE NECK. SELECT REPLY CODE 10AJ91 AQXED /D/ 07CLOSURE,NECK NECK CLOSURE AN INDICATION OF WHETHER OR NOT A NECK CLOSURE IS PROVIDED. SELECT REPLY CODE 10AB22 AQXFG /D/ 19ADDRESS,MANUFACTURER MANUFACTURER ADDRESS THE ADDRESS OF THE MANUFACTURER. FULL TEXT WRITE-IN 0 AQXGG /D/ 19AGENCY,CONTROLLING,SPEC/STD SPEC/STD CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY,COMMERCIAL ORGANIZATION,OR MANUFACTURER CONTROLLING THE SPECIFICATION AND/OR STANDARD. PLEASE USE MRC AMSA IN PLACE OF THIS DISCONTINUED MRC. FULL TEXT WRITE-IN 0 AQXHJ A19NUMBER,IDENTIFYING,SPEC/STD SPEC/STD IDENTIFYING NUMBER THE SPECIFICATION OR STANDARD /GOVERNMENTAL OR INDUSTRIAL/ THAT SPECIFICALLY COVERS THE ITEM BEING DESCRIBED. 1D AND 1A MODE REPLY11AC28 AQXJA 19NUMBER,TYPE,GOVERNMENT GOVERNMENT TYPE NUMBER THE IDENTIFYING TYPE NUMBER ASSIGNED BY THE GOVERNMENT. 1A MODE REPLY 0 AQXKD 19FLEXIBILITY,SIPHON,NECK CLOSURE NECK CLOSURE SIPHON FLEXIBILITY AN INDICATION OF THE FLEXIBILITY OF THE NECK CLOSURE SIPHON. SELECT REPLY CODE 10AD03 AQXLD 19ARRANGEMENT,ROW ROW ARRANGEMENT AN INDICATION OF THE ROW ARRANGEMENT OF THE ITEM. SELECT REPLY CODE 10AH86 AQXMA 12QUANTITY,ROW ROW QUANTITY THE NUMBER OF ROWS IN AN ITEM. 1A MODE REPLY 0 AQXNA 12QUANTITY PER ROW,BANK BANK QUANTITY PER ROW THE NUMBER OF BANKS IN EACH ROW. 1A MODE REPLY 0 AQXPA 12QUANTITY,CONNECTION,INLET INLET CONNECTION QUANTITY THE NUMBER OF INLET CONNECTIONS ON THE ITEM. 1A MODE REPLY 0 AQXQD /D/ 07LEAD,PIGTAIL,FLEXIBLE FLEXIBLE PIGTAIL LEAD AN INDICATION OF WHETHER OR NOT A FLEXIBLE PIGTAIL LEAD(S) IS INCLUDED. SELECT REPLY CODE 10AA49 AQXRA 12QUANTITY,LEAD,FLEXIBLE PIGTAIL FLEXIBLE PIGTAIL LEAD QUANTITY THE NUMBER OF FLEXIBLE PIGTAIL LEADS SUPPLIED. 1A MODE REPLY 0 AQXSD /D/ 07ARRESTOR,FLASH,PIGTAIL PIGTAIL FLASH ARRESTOR AN INDICATION OF WHETHER OR NOT A PIGTAIL FLASH ARRESTOR/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 AQXTD /D/ 07VALVE,SHUT-OFF,INDIVIDUAL CYLINDER INDIVIDUAL CYLINDER SHUT-OFF VALVE AN INDICATION OF WHETHER OR NOT AN INDIVIDUAL CYLINDER SHUT-OFF VALVE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 AQXWD /D/ 07VALVE,PRESSURE,BACK,HYDRAULIC HYDRAULIC BACK PRESSURE VALVE AN INDICATION OF WHETHER OR NOT A HYDRAULIC BACK PRESSURE VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 AQXXD /D/ 07PLUG,INLET INLET PLUG AN INDICATION OF WHETHER OR NOT AN INLET PLUG(S) IS INCLUDED. SELECT REPLY CODE 10AA49 AQXYG 18TYPE FOR WHICH DESIGNED,TEST TEST TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF TEST FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 AQXZG /D/ 19CAPABILITY,TEST,OPERATING OPERATING TEST CAPABILITY THE TESTING FUNCTIONS SUCH AS RANGE,SENSITIVITY,OUTPUT,AND THE LIKE,FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 AQYAJ 04DIAMETER ACCOMMODATED,ARMATURE ARMATURE DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR AN ARMATURE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AQYBJ 10VOLTAGE RATING,OUTPUT OUTPUT VOLTAGE RATING THE OUTPUT VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE. 2D AND 1B MODE REPLY21AB631AC20 AQYCA 12QUANTITY,SIDE,COATED COATED SIDE QUANTITY THE NUMBER OF SIDES OF THE ITEM THAT ARE COATED. 1A MODE REPLY 0 AQYDJ 10CURRENT RATING,OUTPUT OUTPUT CURRENT RATING THE OUTPUT CURRENT RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE. 2D AND 1B MODE REPLY21AC301AC20 AQYEB 10VOLT-AMPERE RATING VOLT-AMPERE RATING THE AMOUNT OF APPARENT POWER,AS DISTINGUISHED FROM TRUE POWER,FOR WHICH THE ITEM IS RATED. 1B MODE REPLY 0 AQYFD 18TYPE,TEST TEST TYPE INDICATES THE TYPE OF TEST THE ITEM IS DESIGNED TO PERFORM. SELECT REPLY CODE 10AL39 AQYGF T10VOLTAGE RATING IN VOLTS,FILAMENT FILAMENT VOLTAGE RATING IN VOLTS THE TOTAL ELECTRICAL VOLTAGE AT WHICH THE FILAMENT IS DESIGNED TO BE OPERATED,EXPRESSED IN VOLTS. 1F MODE REPLY 0 AQYHD 18TYPE FOR WHICH DESIGNED,BATTERY BATTERY TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF BATTERY/IES/ FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AD57 AQYJA 12QUANTITY,HANDLE HANDLE QUANTITY THE NUMBER OF HANDLES PROVIDED ON THE ITEM. 1A MODE REPLY 0 AQYKD 18TYPE,INDICATOR,LEAKAGE LEAKAGE INDICATOR TYPE INDICATES THE TYPE OF INDICATOR USED TO SHOW A LEAKAGE CONDITION. SELECT REPLY CODE 10AJ12 AQYLA 12QUANTITY,LEAD,TEST TEST LEAD QUANTITY THE NUMBER OF TEST LEADS PROVIDED WITH THE ITEM. 1A MODE REPLY 0 AQYMD 19DEVICE,PROTECTION,CIRCUIT OVERLOAD CIRCUIT OVERLOAD PROTECTION DEVICE THE DEVICE PROVIDED TO PROTECT THE CIRCUIT FROM AN ELECTRICAL OVERLOAD CONDITION. SELECT REPLY CODE 10AC08 AQYNJ T10RANGE,SCALE,CAPACITANCE CAPACITANCE SCALE RANGE THE MINIMUM TO MAXIMUM LIMITS OF THE CAPACITANCE SCALE. 1D AND 1F MODE REPLY12AB49 AQYPF T10ACCURACY RATING IN PERCENT,OVERALL,CAPACITANCE SCALE CAPACITANCE SCALE OVERALL ACCURACY RATING IN PERCENT THE MINIMUM AND MAXIMUM DEVIATION FROM THE EXACT CAPACITANCE READING AT FULL SCALE DEFLECTION,EXPRESSED IN PERCENT. 1F MODE REPLY 0 AQYQA 03DESIGNATOR,NUMERIC NUMERIC DESIGNATOR THE NUMBER ASSIGNED TO DESIGNATE THE ITEM. 1A MODE REPLY 0 AQYRJ 04DIAMETER,HOLE,ARBOR ARBOR HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ARBOR HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AQYSA /D/ 12QUANTITY PER SET,FILE FILE QUANTITY PER SET THE NUMBER OF FILES IN A SET. 1A MODE REPLY 0 AQYTA 03DESIGNATOR,CUT CUT DESIGNATOR THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE CUT. 1A MODE REPLY 0 AQYWB 10VOLTAGE IN VOLTS,MOTOR,SYNCHRONOUS SYNCHRONOUS MOTOR VOLTAGE IN VOLTS THE ELECTRICAL VOLTAGE OF THE SYNCHRONOUS MOTOR,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AQYXD 01COLOR,BACKGROUND,DRUM DRUM BACKGROUND COLOR THE HUE OR TINT OF THE DRUM BACKGROUND. SELECT REPLY CODE 10AD06 AQYYD /D/ 07DRUM,SECONDS,CONTINUOUS REVOLUTION CONTINUOUS REVOLUTION SECONDS DRUM AN INDICATION OF WHETHER OR NOT A CONTINUOUS REVOLUTION SECONDS DRUM IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AQYZD 18TYPE,DRUM,INTERVAL INTERVAL DRUM TYPE INDICATES THE TYPE OF INTERVAL DRUM PROVIDED. SELECT REPLY CODE 10AL14 AQZAG 19MARKING,NUMERICAL,DRUM DRUM NUMERICAL MARKING AN INDICATION OF THE NUMERICAL MARKING(S) ON THE DRUM. FULL TEXT WRITE-IN 0 AQZBD 01COLOR,NUMERAL NUMERAL COLOR THE HUE OR TINT OF THE NUMERAL. SELECT REPLY CODE 10AD06 AQZCD 05DIRECTION FOR WHICH DESIGNED,STROKE,CUT CUT STROKE DIRECTION FOR WHICH DESIGNED THE STROKE DIRECTION FOR WHICH THE ITEM IS DESIGNED TO CUT. SELECT REPLY CODE 10AA38 AQZDD /D/ 07CLUTCH,OPERATED,DC DC OPERATED CLUTCH AN INDICATION OF WHETHER OR NOT A DIRECT CURRENT OPERATED CLUTCH IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AQZEA /D/ 16STYLE DESIGNATOR,TOOTH,CUTTER CUTTER TOOTH STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CUTTER TOOTH. 1A MODE REPLY 0 AQZFD 18TYPE,CONTROL CONTROL TYPE INDICATES THE TYPE OF CONTROL. SELECT REPLY CODE 10AL37 AQZGD 16STYLE,CUT,CUTTER TOOTH CUTTER TOOTH CUT STYLE THE STYLE INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE CUT OF THE CUTTER TOOTH. SELECT REPLY CODE 10AF67 AQZHD 11METHOD,SHAPING,CUTTER TOOTH CUTTER TOOTH SHAPING METHOD THE MEANS USED TO ATTAIN THE SHAPE OF THE CUTTER TOOTH. SELECT REPLY CODE 10AL38 AQZJD /D/ 07SHANK,MOUNTING MOUNTING SHANK AN INDICATION OF WHETHER OR NOT A MOUNTING SHANK IS INCLUDED. SELECT REPLY CODE 10AA49 AQZKD /D/ 07FEATURE,REMOVABILITY REMOVABILITY FEATURE AN INDICATION OF WHETHER OR NOT A REMOVABILITY FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AQZLD 19SERIES,TAPER TAPER SERIES AN INDUSTRIAL DESIGNATOR USED TO INDICATE THE TAPER. SELECT REPLY CODE 10AH09 AQZMD 18TYPE,CUT CUT TYPE INDICATES THE TYPE OF CUT PROVIDED. SELECT REPLY CODE 10AL18 AQZNJ A12QUANTITY PER UNIT OF MEASURE,TEETH TEETH QUANTITY PER UNIT OF MEASURE THE NUMBER OF TEETH PER SPECIFIC UNIT OF MEASURE. 1D AND 1A MODE REPLY11AB39 AQZPD /D/ 07FEATURE,HEAD,REVOLVING REVOLVING HEAD FEATURE AN INDICATION OF WHETHER OR NOT A REVOLVING HEAD IS INCLUDED. SELECT REPLY CODE 10AA49 AQZQJ 04HEIGHT,SHANK SHANK HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE SHANK,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AQZRD 19PATTERN,KNURL KNURL PATTERN THE PHYSICAL CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE GENERAL APPEARANCE OF THE KNURL. SELECT REPLY CODE 10AD07 AQZSJ 04DIAMETER,OUTSIDE,KNURL KNURL OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE KNURL,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AQZTJ 04WIDTH,OVERALL,KNURL ROLL KNURL ROLL OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE KNURL ROLL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AQZWJ 04DIAMETER,PINHOLE,KNURL KNURL PINHOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE KNURL PINHOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AQZXJ 04WIDTH,FACE,KNURLING KNURLING FACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE KNURLING FACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AQZYJ 10CAPACITY,KNURLING,MINIMUM MINIMUM KNURLING CAPACITY THE MINIMUM CAPACITY OF THE KNURL. 1D AND 1B MODE REPLY11AA05 AQZZJ 04WIDTH,CUT CUT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CUT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ARAAJ 04LENGTH,SURFACE,CUTTING CUTTING SURFACE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ARABD 19FORM,FINAL FINAL FORM AN INDICATION OF THE FINAL FORM OF THE ITEM. SELECT REPLY CODE 10AK16 ARACJ 04WIDTH,BELT BELT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BELT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ARADD /D/ 07RECEPTACLE,DUST DUST RECEPTACLE AN INDICATION OF WHETHER OR NOT A DUST RECEPTACLE IS INCLUDED. SELECT REPLY CODE 10AA49 ARAED /D/ 07SWITCH,CONTROL,AUTOMATIC ELECTRIC CIRCUIT AUTOMATIC ELECTRIC CIRCUIT CONTROL SWITCH AN INDICATION OF WHETHER OR NOT AN AUTOMATIC ELECTRIC CIRCUIT CONTROL SWITCH IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 ARAFB 10VOLTAGE IN VOLTS,SWITCH,CONTROL CONTROL SWITCH VOLTAGE IN VOLTS THE TOTAL ELECTRICAL VOLTAGE IN VOLTS,OF THE CONTROL SWITCH. 1B MODE REPLY 0 ARAGJ 10CURRENT RATING CURRENT RATING THE AMOUNT OF CURRENT FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AC30 ARAHD /D/ 08LOCATION,TAP,CONTROL SWITCH OUTLET CONTROL SWITCH OUTLET TAP LOCATION THE PHYSICAL LOCATION OF THE CONTROL SWITCH OUTLET TAP. SELECT REPLY CODE 10AJ91 ARAJD /D/ 07DEVICE,SIGNALLING,INTERVAL EXPIRATION INTERVAL EXPIRATION SIGNALLING DEVICE AN INDICATION OF WHETHER OR NOT AN INTERVAL EXPRIATION SIGNALLING DEVICE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 ARAKD /D/ 07BASE,PETROLATUM PETROLATUM BASE AN INDICATION OF WHETHER OR NOT PETROLATUM BASE IS INCLUDED. SELECT REPLY CODE 10AA49 ARALD /D/ 07FEATURE,NONTOXIC NONTOXIC FEATURE AN INDICATION OF WHETHER OR NOT A NONTOXIC FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARAMD /D/ 07FEATURE,NONSLICK NONSLICK FEATURE AN INDICATION OF WHETHER OR NOT A NONSLICK FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARAND /D/ 07FEATURE,PIGMENT PIGMENT FEATURE AN INDICATION OF WHETHER OR NOT A PIGMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARAPJ 04THICKNESS,FILM FILM THICKNESS THE THICKNESS OF THE FILM AFTER APPLYING TO AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 ARAQD 03DESIGNATION,HARDNESS,FILM FILM HARDNESS DESIGNATION THE DESIGNATION INDICATING THE HARDNESS OF THE FILM. SELECT REPLY CODE 10AK55 ARARJ 10TEMP RATING,POINT,MELTING MELTING POINT TEMP RATING THE TEMPERATURE AT WHICH THE ITEM WILL MELT. 1D AND 1B MODE REPLY11AB36 ARASJ 10PENETRATION RATE,UNWORKED UNWORKED PENETRATION RATE THE RATED UNWORKED PENETRATION OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ARATJ /D/ 10CONTENT,TOXIC,MINIMUM MINIMUM TOXIC CONTENT AN INDICATION OF THE MINIMUM TOXIC CONTENT OF THE ITEM. 1D AND 1B MODE REPLY12AB49 ARAWJ 10FLASH POINT,MINIMUM MINIMUM FLASH POINT THE MINIMUM DEGREES AT WHICH THE ITEM WILL IGNITE AND BURN. 1D AND 1B MODE REPLY13AJ40 ARAXD 11METHOD,TEST TEST METHOD THE MEANS USED FOR TESTING THE ITEM. SELECT REPLY CODE 10AL43 ARAYG /D/ 10TIME,DRYING,RATED RATED DRYING TIME THE TIME REQUIRED FOR THE ITEM TO DRY. FULL TEXT WRITE-IN 0 ARAZD 19INGREDIENTS,COMPONENT,RESIN RESIN COMPONENT INGREDIENTS THE RESIN COMPONENT WHICH IS ADDED TO OR MIXED WITH THE BASIC ITEM. SELECT REPLY CODE 10AF11 ARBAD 19INGREDIENTS,COMPONENT,ACID ACID COMPONENT INGREDIENTS THE ACID COMPONENT WHICH IS ADDED TO OR MIXED WITH THE BASIC ITEM. SELECT REPLY CODE 10AF11 ARBBG /D/ 10TIME AFTER MIXING,EFFECTIVE,MAXIMUM MAXIMUM EFFECTIVE TIME AFTER MIXING THE MAXIMUM EFFECTIVE TIME OF THE ITEM AFTER MIXING. FULL TEXT WRITE-IN 0 ARBCG /D/ 10TIME AFTER APPLICATION,EFFECTIVE,MAXIMUM MAXIMUM EFFECTIVE TIME AFTER APPLICATION THE MAXIMUM EFFECTIVE TIME AFTER APPLYING. FULL TEXT WRITE-IN 0 ARBDD /D/ 07PRIMER PRIMER AN INDICATION OF WHETHER OR NOT A PRIMER IS REQUIRED. SELECT REPLY CODE 10AE40 ARBED 01COLOR,PIGMENT PIGMENT COLOR THE HUE OR TINT OF THE PIGMENT. SELECT REPLY CODE 10AD06 ARBFD /D/ 07FEATURE,THINNING,WATER WATER THINNING FEATURE AN INDICATION OF WHETHER OR NOT A WATER THINNING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARBGG /D/ 10TIME,WORKING,RATED RATED WORKING TIME THE RATED WORKING TIME OF THE ITEM. FULL TEXT WRITE-IN 0 ARBHD /D/ 09MATERIAL FOR WHICH FORMULATED MATERIAL FOR WHICH FORMULATED THE ELEMENT,COMPOUND,OR MIXTURE FOR WHICH THE ITEM IS FORMULATED. SELECT REPLY CODE 10AD09 ARBJD /D/ 09MATERIAL FOR WHICH FORMULATED,SPECIFIC SPECIFIC MATERIAL FOR WHICH FORMULATED THE SPECIFIC ELEMENT,COMPOUND,OR MIXTURE FOR WHICH THE ITEM IS FORMULATED. SELECT REPLY CODE 10AD09 ARBKD 19CHARACTERISTIC,IGNITING IGNITING CHARACTERISTIC INDICATES THE IGNITING CHARACTERISTIC OF THE ITEM. SELECT REPLY CODE 10AD43 ARBLD /D/ 07GLASS,STRESS,HIGH HIGH STRESS GLASS AN INDICATION AS TO WHETHER OR NOT HIGH STRESS GLASS HAS BEEN INCLUDED. SELECT REPLY CODE 10AA49 ARBMD 19CONDITION,SURFACE,OUTER OUTER SURFACE CONDITION THE CONDITION OF THE ITEM WITH RESPECT TO THE TEXTURE OF THE OUTER SURFACE. SELECT REPLY CODE 10AK39 ARBNJ /D/ 04DIAMETER,OUTSIDE,SEAL RING SEAL RING OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SEAL RING,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARBPJ /D/ 04DIAMETER,INSIDE,SEAL RING SEAL RING INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SEAL RING,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARBQD /D/ 09MATERIAL,TUBE,ROD ENCASING ROD ENCASING TUBE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ROD ENCASING TUBE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ARBRJ 04DEPTH,BODY BODY DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON A BODY IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 ARBSJ 04DIAMETER,ACCOMMODATED,STARTER ACCOMMODATED STARTER DIAMETER A MEASUREMENT OF A CHORD OR STRAIGHT LINE PASSING THROUGH THE CENTER OF THE STARTER ACCOMMODATED BY THE ITEM. 1D AND 1B MODE REPLY11AA05 ARBTJ /D/ 04LENGTH,SHAFT SHAFT LENGTH NONE. 3D AND 1B MODE REPLY31AA051AC202AD87 ARBWJ /D/ 04DIAMETER,SHAFT SHAFT DIAMETER NONE. 3D AND 1B MODE REPLY31AA051AC202AD87 ARBXJ /D/ 04DIAMETER,INSIDE,BODY BODY INSIDE DIAMETER NONE. 3D AND 1B MODE REPLY31AA051AC202AD87 ARBYJ /D/ 04WIDTH BETWEEN FLATS WIDTH BETWEEN FLATS NONE. 3D AND 1B MODE REPLY31AA051AC202AD87 ARBZJ /D/ 04LENGTH,FLAT,FIRST FIRST FLAT LENGTH NONE. 3D AND 1B MODE REPLY31AA051AC202AD87 ARCAJ /D/ 04HEIGHT,FLAT FLAT HEIGHT NONE. 3D AND 1B MODE REPLY31AA051AC202AD87 ARCBJ /D/ 04DEPTH,SLOT SLOT DEPTH NONE. 3D AND 1B MODE REPLY31AA051AC202AD87 ARCCJ /D/ 04WIDTH,SLOT SLOT WIDTH NONE. 3D AND 1B MODE REPLY31AA051AC202AD87 ARCDJ /D/ 04LENGTH,TIP TIP LENGTH NONE. 3D AND 1B MODE REPLY31AA051AC202AD87 ARCEG /D/ 10CAPACITY,TOTAL,TIME INDICATOR TIME INDICATOR TOTAL CAPACITY THE TOTAL MEASURED CONTENT OF THE TIME INDICATOR. FULL TEXT WRITE-IN 0 ARCFG 10SPEED,HAND,FAST FAST HAND SPEED THE RATE OF MOTION OF THE FAST HAND. FULL TEXT WRITE-IN 0 ARCGD 01COLOR,BACKGROUND,DIAL DIAL BACKGROUND COLOR THE HUE OR TINT OF THE DIAL BACKGROUND. SELECT REPLY CODE 10AD06 ARCHG 04SIZE,DIAL DIAL SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE DIAL. FULL TEXT WRITE-IN 0 ARCJD 02DESIGN,DIRECTION,SOUND PROJECTOR SOUND PROJECTOR DIRECTION DESIGN THE PROJECTED SOUND EMISSION ANGLE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK50 ARCKG /D/ 10GRADUATION,MINIMUM,DIAL DIAL MINIMUM GRADUATION THE SMALLEST GRADUATION DISPLAYED ON THE DIAL. PLEASE USE MRC CNKX IN PLACE OF THIS DISCONTINUED MRC. FULL TEXT WRITE-IN 0 ARCLJ A03DESIGNATION AND QUANTITY,HAND HAND DESIGNATION AND QUANTITY THE DESIGNATION USED TO IDENTIFY THE HAND AND NUMBER PROVIDED. 1D AND 1A MODE REPLY13AL26 ARCMD 11METHOD,DRIVE DRIVE METHOD THE MEANS BY WHICH THE ITEM IS DRIVEN. SELECT REPLY CODE 10AL40 ARCND 19VARIETY,FOOD FOOD VARIETY A NAME WHICH REPRESENTS A SUB-DIVISION OF A FOOD. SELECT REPLY CODE 10AL42 ARCPD 19STAGE,MATURITY MATURITY STAGE THE DEGREE OF MATURITY OF THE ITEM. SELECT REPLY CODE 10AL44 ARCQD 11METHOD,PACK PACK METHOD THE MEANS BY WHICH THE ITEM IS PACKED. SELECT REPLY CODE 10AL45 ARCRD /D/ 07CLOCK,OPERATED,INDEPENDENTLY INDEPENDENTLY OPERATED CLOCK AN INDICATION OF WHETHER OR NOT AN INDEPENDENTLY OPERATED CLOCK IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 ARCSD 18TYPE,PRINTOUT,RECORDER RECORDER PRINTOUT TYPE INDICATES THE TYPE OF PRINTOUT THE ITEM WILL RECORD. SELECT REPLY CODE 10AL46 ARCTD 19POSITION,RECORDING RECORDING POSITION THE POSITION IN WHICH THE ITEM WILL RECORD OR PRINT. SELECT REPLY CODE 10AC60 ARCWA 12QUANTITY,COLOR,PRINTED PRINTED COLOR QUANTITY THE NUMBER OF COLORS THE ITEM IS DESIGNED TO PRINT. 1A MODE REPLY 0 ARCXD 18TYPE,POSITIONING,DOCUMENT DOCUMENT POSITIONING TYPE INDICATES THE TYPE OF MECHANISM THAT POSITIONS THE DOCUMENT. SELECT REPLY CODE 10AL47 ARCYD 11METHOD,ACTUATION,PRINTING MECHANISM PRINTING MECHANISM ACTUATION METHOD THE MEANS USED TO ACTUATE THE PRINTING MECHANISM. SELECT REPLY CODE 10AL47 ARCZD 18TYPE,DRIVE,PRIMARY CIRCUIT PRIMARY CIRCUIT DRIVE TYPE INDICATES THE TYPE OF PRIMARY CIRCUIT DRIVE. SELECT REPLY CODE 10AG25 ARDAJ 10VOLTAGE,CIRCUIT,PRIMARY PRIMARY CIRCUIT VOLTAGE THE TOTAL ELECTRICAL VOLTAGE OF THE PRIMARY CIRCUIT. 2D AND 1B MODE REPLY21AB621AC20 ARDBB 10FREQUENCY,CIRCUIT,PRIMARY PRIMARY CIRCUIT FREQUENCY THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT. 1B MODE REPLY 0 ARDCD 10PHASE,CIRCUIT,PRIMARY PRIMARY CIRCUIT PHASE THE NUMBER OF ALTERNATING CURRENT PHASES OF THE PRIMARY CIRCUIT. SELECT REPLY CODE 10AD02 ARDDB 12QUANTITY,BEAT,PRIMARY CIRCUIT PRIMARY CIRCUIT BEAT QUANTITY THE NUMBER OF BEATS /PULSES/ THAT OCCUR PER SECOND IN THE PRIMARY CIRCUIT. 1B MODE REPLY 0 ARDED 18TYPE,DRIVE,SUPERVISING CIRCUIT SUPERVISING CIRCUIT DRIVE TYPE INDICATES THE TYPE OF SUPERVISING CIRCUIT DRIVE. SELECT REPLY CODE 10AG25 ARDFJ 10VOLTAGE,CIRCUIT,SUPERVISING SUPERVISING CIRCUIT VOLTAGE THE TOTAL ELECTRICAL VOLTAGE OF THE SUPERVISING CIRCUIT. 2D AND 1B MODE REPLY21AB621AC20 ARDGB 10FREQUENCY,CIRCUIT,SUPERVISING SUPERVISING CIRCUIT FREQUENCY THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT. 1B MODE REPLY 0 ARDHD 10PHASE,CIRCUIT,SUPERVISING SUPERVISING CIRCUIT PHASE THE NUMBER OF ALTERNATING CURRENT PHASES OF THE SUPERVISING CIRCUIT. SELECT REPLY CODE 10AD02 ARDJB 12QUANTITY,BEAT,SUPERVISING CIRCUIT SUPERVISING CIRCUIT BEAT QUANTITY THE NUMBER OF BEATS /PULSES/ THAT OCCUR PER SECOND IN THE SUPERVISING CIRCUIT. 1B MODE REPLY 0 ARDKA 12QUANTITY,WIRE,SUPERVISING CIRCUIT SUPERVISING CIRCUIT WIRE QUANTITY THE NUMBER OF WIRES CONTAINED IN THE SUPERVISING CIRCUIT. 1A MODE REPLY 0 ARDLD 18TYPE,DRIVE,MECHANICAL MECHANICAL DRIVE TYPE INDICATES THE TYPE OF MECHANICAL DRIVE. SELECT REPLY CODE 10AG25 ARDMA 19NUMBER,MODEL,CANNON CANNON MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE CANNON. 1A MODE REPLY 0 ARDNJ 04HEIGHT,OPENING OPENING HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN OPENING,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 ARDPJ 04DIAMETER,DISK DISK DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A DISK,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARDQJ 04LENGTH,TABLE TABLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A TABLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARDRJ 04WIDTH,TABLE TABLE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A TABLE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ARDSF /D/T04ANGLE IN DEG,TILT,TABLE TABLE TILT ANGLE IN DEG THE LIMITS OF VARIATION IN THE TILT ANGLE OF A TABLE,EXPRESSED IN DEGREES. 1F MODE REPLY 0 ARDTD /D/ 07HANDLE,SIDE,AUXILIARY AUXILIARY SIDE HANDLE AN INDICATION OF WHETHER OR NOT AN AUXILIARY SIDE HANDLE IS INCLUDED. SELECT REPLY CODE 10AA49 ARDWD 19RELATIONSHIP,DRIVE AXIS TO WORK SURFACE DRIVE AXIS TO WORK SURFACE RELATIONSHIP THE RELATIONSHIP OF THE DRIVE AXIS WITH RESPECT TO THE WORK SURFACE. SELECT REPLY CODE 10AF63 ARDXJ 10SPEED IN RPM,ABRASIVE ABRASIVE SPEED IN RPM THE SPEED OF THE ABRASIVE EXPRESSED IN REVOLUTIONS PER MINUTE. 1D AND 1B MODE REPLY11AC20 ARDYJ 10VOLTAGE,TEST,LEAKAGE,DC DC LEAKAGE TEST VOLTAGE THE APPLIED ELECTRICAL POTENTIAL USED TO DETERMINE THE DIRECT CURRENT LEAKAGE VALUE OF AN ITEM. 1D AND 1B MODE REPLY11AC20 ARDZF T10FACTOR IN PERCENT,DISSIPATION DISSIPATION FACTOR IN PERCENT THE LIMITS OF THE RATIO OF RESISTANCE TO CAPACITIVE REACTANCE,IN PERCENT. 1F MODE REPLY 0 AREBJ T10RANGE,SCALE,INDUCTANCE INDUCTANCE SCALE RANGE THE MINIMUM TO MAXIMUM LIMITS OF THE INDUCTANCE SCALE. 1D AND 1F MODE REPLY12AB49 ARECF T10ACCURACY RATING IN PERCENT,OVERALL,INDUCTANCE SCALE INDUCTANCE SCALE OVERALL ACCURACY RATING IN PERCENT THE MINIMUM AND MAXIMUM DEVIATION FROM THE EXACT INDUCTANCE READING AT FULL SCALE DEFLECTION. 1F MODE REPLY 0 AREDJ T10RANGE,SCALE,RESISTANCE RESISTANCE SCALE RANGE THE MINIMUM TO MAXIMUM LIMITS OF THE RESISTANCE SCALE. 1D AND 1F MODE REPLY12AB49 AREEF T10ACCURACY RATING IN PERCENT,OVERALL,RESISTANCE SCALE RESISTANCE SCALE OVERALL ACCURACY RATING IN PERCENT THE MINIMUM AND MAXIMUM DEVIATION FROM THE EXACT RESISTANCE READING AT FULL SCALE DEFLECTION. 1F MODE REPLY 0 AREFJ T10RANGE,FREQUENCY,OUTPUT OUTPUT FREQUENCY RANGE THE RANGE OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE OUTPUT OF THE ITEM IS RATED. 1D AND 1F MODE REPLY11AC32 AREGD 11METHOD,ADJUSTMENT ADJUSTMENT METHOD THE MEANS PROVIDED TO ADJUST AN ITEM. SELECT REPLY CODE 10AL41 AREHD 18TYPE,INDICATOR,BALANCE BALANCE INDICATOR TYPE THE TYPE OF INDICATOR USED TO SIGNIFY WHETHER THE ITEM IS IN BALANCE. SELECT REPLY CODE 10AJ12 AREJD 08LOCATION,OSCILLATOR OSCILLATOR LOCATION THE LOCATION OF THE OSCILLATOR. SELECT REPLY CODE 10AJ91 AREKJ 10FREQUENCY RATING,OSCILLATOR OSCILLATOR FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE OSCILLATOR IS DESIGNED. 1D AND 1B MODE REPLY11AC32 ARELF T10RANGE IN PERCENT,ACCURACY,FREQUENCY CALIBRATION FREQUENCY CALIBRATION ACCURACY RANGE IN PERCENT THE LIMITS OF PERMISSIBLE VARIANCE FROM THE STANDARD/TRUE VALUE,EXPRESSED IN PERCENT. 1F MODE REPLY 0 AREMD /D/ 19INFORMATION,DISPLAYED,TUBE,RAY,CATHODE CATHODE RAY TUBE DISPLAYED INFORMATION THE INFORMATION DISPLAYED ON THE CATHODE RAY TUBE. SELECT REPLY CODE 10AK09 ARENJ T10RANGE,FREQUENCY,INPUT INPUT FREQUENCY RANGE THE RANGE OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE INPUT OF THE ITEM IS RATED. 1D AND 1F MODE REPLY11AC32 AREPJ 10POWER RATING,INPUT,RADIO FREQUENCY RADIO FREQUENCY INPUT POWER RATING THE AMOUNT OF INPUT RADIO FREQUENCY POWER AT WHICH THE ITEM IS RATED FOR OPERATION. 2D AND 1B MODE REPLY21AC331AC20 AREQD 19ACCOMMODATION,CHANNEL,AMPLIFIER AMPLIFIER CHANNEL ACCOMMODATION AN INDICATION OF THE AMPLIFIER CHANNEL ACCOMMODATION/S/ ON THE ITEM. SELECT REPLY CODE 10AH86 ARERD /D/ 07INDICATOR INDICATOR AN INDICATION OF WHETHER OR NOT AN INDICATOR IS INCLUDED. SELECT REPLY CODE 10AA49 ARESD 18TYPE,TERMINATION,TIP TIP TERMINATION TYPE THE TYPE OF TIP TERMINATION PROVIDED ON THE ITEM. SELECT REPLY CODE 10AE79 ARETG 11METHOD,ATTACHMENT,CONDUCTOR CONDUCTOR ATTACHMENT METHOD THE MEANS BY WHICH THE CONDUCTOR ATTACHES TO THE ITEM. FULL TEXT WRITE-IN 0 AREWB 10CAPACITY IN SQUARE FEET,RADIATION RADIATION CAPACITY IN SQUARE FEET THE TOTAL AMOUNT OF RADIATION IN SQUARE FEET FOR WHICH THE ITEM IS RATED. 1B MODE REPLY 0 AREYD 02DESIGN,SYSTEM,IGNITION IGNITION SYSTEM DESIGN AN INDICATION OF THE DESIGN OF THE IGNITION SYSTEM. SELECT REPLY CODE 10AB03 AREZD /D/ 11METHOD,DISTRIBUTION,SPARK SPARK DISTRIBUTION METHOD THE SPARK DISTRIBUTION METHOD USED. SELECT REPLY CODE 10AF04 ARFAD /D/ 18TYPE,CONTROL,SPARK SPARK CONTROL TYPE THE TYPE OF SPARK CONTROL PROVIDED. SELECT REPLY CODE 10AC58 ARFBJ /D/ 04ANGLE IN DEG,ADVANCE ADVANCE ANGLE IN DEG AN INDICATION OF THE ADVANCE ANGLE,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 ARFCB /D/ 10SPEED IN RPM,ENGINE,CORRESPONDING CORRESPONDING ENGINE SPEED IN RPM THE RATED SPEED,IN REVOLUTIONS PER MINUTE,OF THE CORRESPONDING ENGINE. 1B MODE REPLY 0 ARFDJ /D/ 10VACUUM RATING,CONTROL CONTROL VACUUM RATING AN INDICATION OF THE AMOUNT OF VACUUM USED TO CONTROL THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ARFED /D/ 07CAP,DISTRIBUTOR DISTRIBUTOR CAP AN INDICATION OF WHETHER OR NOT A DISTRIBUTOR CAP IS INCLUDED. SELECT REPLY CODE 10AA49 ARFFD 18TYPE,CONNECTION,SPARK PLUG LEAD SPARK PLUG LEAD CONNECTION TYPE AN INDICATION OF THE TYPE OF SPARK PLUG LEAD CONNECTION. SELECT REPLY CODE 10AJ68 ARFGD 18TYPE,CONNECTION,COIL LEAD COIL LEAD CONNECTION TYPE AN INDICATION OF THE TYPE OF COIL LEAD CONNECTION. SELECT REPLY CODE 10AJ68 ARFHD 13THREAD LOCATION,CONNECTION CONNECTION THREAD LOCATION INDICATES THE LOCATION OF THE THREADS ON THE CONNECTION. SELECT REPLY CODE 10AJ91 ARFJD 13THREAD DIRECTION,CONNECTION CONNECTION THREAD DIRECTION THE DIRECTION OF THE CONNECTION THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ARFKD /D/ 07CONNECTION,DRIVE,TACHOMETER TACHOMETER DRIVE CONNECTION AN INDICATION OF WHETHER OR NOT A TACHOMETER DRIVE CONNECTION IS INCLUDED. SELECT REPLY CODE 10AA49 ARFLD /D/ 07FEATURE,DRIVE,HORIZONTAL HORIZONTAL DRIVE FEATURE AN INDICATION OF WHETHER OR NOT A HORIZONTAL DRIVE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARFMD /D/ 07COIL,IGNITION IGNITION COIL AN INDICATION OF WHETHER OR NOT AN IGNITION COIL IS INCLUDED. SELECT REPLY CODE 10AA49 ARFND /D/ 18TYPE,TENSION TENSION TYPE AN INDICATION OF THE TYPE OF TENSION. SELECT REPLY CODE 10AK09 ARFQD /D/ 07SWITCH,GROUNDING GROUNDING SWITCH AN INDICATION OF WHETHER OR NOT A GROUNDING SWITCH IS INCLUDED. SELECT REPLY CODE 10AA49 ARFRJ /D/A12QUANTITY,LEAD,SPARK PLUG SPARK PLUG LEAD QUANTITY THE NUMBER OF SPARK PLUG LEADS ACCOMMODATED OR INCLUDED. 1D AND 1A MODE REPLY11AA49 ARFSA /D/ 12QUANTITY,SET,CONTACT CONTACT SET QUANTITY THE NUMBER OF CONTACT SETS INCLUDED. 1A MODE REPLY 0 ARFTD /D/ 07THROTTLE,SAFETY SAFETY THROTTLE INDICATES WHETHER OR NOT A SAFETY THROTTLE IS INCLUDED. SELECT REPLY CODE 10AA49 ARFWD 07ADJUSTABILITY,PLANE,BELT BELT PLANE ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE BELT IS ADJUSTABLE BETWEEN THE HORIZONTAL AND VERTICAL PLANE. SELECT REPLY CODE 10AL36 ARFXD 18TYPE,SANDER SANDER TYPE AN INDICATION OF THE TYPE OF SANDER. SELECT REPLY CODE 10AL48 ARFYJ 04LENGTH,BELT BELT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A BELT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARFZD /D/ 07CABLE,POWER POWER CABLE AN INDICATION OF WHETHER OR NOT A POWER CABLE IS INCLUDED. SELECT REPLY CODE 10AA49 ARGAD /D/ 07HEADLIGHT HEADLIGHT AN INDICATION OF WHETHER OR NOT A HEADLIGHT IS INCLUDED. SELECT REPLY CODE 10AA49 ARGBJ /D/ 10AREA,CONTACT,ABRASIVE ABRASIVE CONTACT AREA A MEASUREMENT OF THE TOTAL OUTSIDE ABRASIVE CONTACT SURFACE. 1D AND 1B MODE REPLY11AC51 ARGCD /D/ 07FEATURE,MAGNETIC MAGNETIC FEATURE AN INDICATION OF WHETHER OR NOT A MAGNETIC FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARGDJ 10WEIGHT,HEAD HEAD WEIGHT A RELATIVE MEASURE OF THE MASS OF A HEAD WITH RESPECT TO ITS DENSITY. 1D AND 1B MODE REPLY12AB16 ARGED /D/ 09MATERIAL,HEAD HEAD MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HEAD IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ARGFD 03DESIGNATION,HARDNESS HARDNESS DESIGNATION AN INDICATION OF THE RELATIVE HARDNESS OF THE ITEM. SELECT REPLY CODE 10AK55 ARGGJ 04DIAMETER,FACE FACE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FACE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARGHD 14SHAPE,FACE,STRIKING STRIKING FACE SHAPE THE PHYSICAL CONFIGURATION OF THE STRIKING FACE. SELECT REPLY CODE 10AD07 ARGJL /D/ 16STYLE DESIGNATOR,HAMMER-BRUSH HAMMER-BRUSH STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HAMMER-BRUSH. 1L MODE REPLY 0 ARGKD /D/ 07REMOVABILITY,BRUSH BRUSH REMOVABILITY AN INDICATION OF WHETHER OR NOT THE BRUSH IS REMOVABLE. SELECT REPLY CODE 10AC29 ARGLD 19CHARACTERISTIC,FACTOR,POWER POWER FACTOR CHARACTERISTIC THE CHARACTERISTIC OF THE POWER FACTOR. SELECT REPLY CODE 10AH10 ARGMD 18TYPE ACCOMMODATED,FACE FACE TYPE ACCOMMODATED INDICATES THE TYPE OF FACE THAT THE ITEM WILL ACCOMMODATE. SELECT REPLY CODE 10AK95 ARGND 05DIRECTION,REMOVAL,CARTRIDGE CARTRIDGE REMOVAL DIRECTION THE DIRECTION THE ITEM IS DESIGNED TO REMOVE A CARTRIDGE. SELECT REPLY CODE 10AA38 ARGPD /D/ 07LAMINATION,MATERIAL,BARRIER BARRIER MATERIAL LAMINATION AN INDICATION OF WHETHER OR NOT LAMINATED BARRIER MATERIAL IS INCLUDED. SELECT REPLY CODE 10AA49 ARGQA /D/ 12QUANTITY,WEAVING,WARP ENDS WARP ENDS WEAVING QUANTITY THE NUMBER OF WARP ENDS THAT ARE WOVEN AS ONE. 1A MODE REPLY 0 ARGRA 12QUANTITY,WEAVING,FILLING ENDS FILLING ENDS WEAVING QUANTITY THE NUMBER OF FILLING ENDS THAT ARE WOVEN AS ONE. 1A MODE REPLY 0 ARGSA /D/ 12QUANTITY PER INCH,THREAD,WARP WARP THREAD QUANTITY PER INCH THE NUMBER OF WARP THREADS PER INCH. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1A MODE REPLY 0 ARGTA /D/ 12QUANTITY PER INCH,THREAD,FILLING FILLING THREAD QUANTITY PER INCH THE NUMBER OF FILLING THREADS PER INCH. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1A MODE REPLY 0 ARGWD 18TYPE,PLATE PLATE TYPE THE TYPE OF PLATE PROVIDED. SELECT REPLY CODE 10AG39 ARGXD 01COLOR,SOLID SOLID COLOR THE HUE OR TINT OF THE SOLID COLOR. SELECT REPLY CODE 10AD06 ARGYG /D/ 19CONTROLLER,DESIGNATION,SHADE SHADE DESIGNATION CONTROLLER THE NAME OF THE GOVERNMENT AGENCY,COMMERCIAL ORGANIZATION,OR MANUFACTURER CONTROLLING THE SHADE DESIGNATION. FULL TEXT WRITE-IN 0 ARGZG /D/ 19AGENCY,CONTROLLING,PRINT/WOVEN PRINT/WOVEN CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY,COMMERCIAL ORGANIZATION,OR MANUFACTURER CONTROLLING THE PRINT/WOVEN PATTERN. FULL TEXT WRITE-IN 0 ARHAA /D/ 03DESIGNATOR,IDENTIFICATION,PRINT/WOVEN PRINT/WOVEN IDENTIFICATION DESIGNATOR A DESIGNATION ASSIGNED TO A PRINT OR WOVEN MATERIAL FOR PURPOSES OF READY IDENTIFICATION. 1A MODE REPLY 0 ARHBD /D/ 01COLOR,STRIPE/CHECK STRIPE/CHECK COLOR THE HUE OR TINT OF THE STRIPE(S) OR CHECK(S). SELECT REPLY CODE 10AD06 ARHCG /D/ 19AGENCY,CONTROLLING,STRIPE/CHECK STRIPE/CHECK CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY,COMMERCIAL ORGANIZATION,OR MANUFACTURER CONTROLLING THE STRIPE/S/ OR CHECK/S/ PATTERN. FULL TEXT WRITE-IN 0 ARHDD /D/ 07FEATURE,BODY,NO-BOUNCE NO-BOUNCE BODY FEATURE AN INDICATION OF WHETHER OR NOT A NO-BOUNCE BODY FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARHEA /D/ 03DESIGNATOR,IDENTIFICATION,STRIPE/CHECK STRIPE/CHECK IDENTIFICATION DESIGNATOR A DESIGNATION ASSIGNED TO A STRIPED OR CHECKED DESIGNED MATERIAL FOR PURPOSES OF READY IDENTIFICATION. 1A MODE REPLY 0 ARHFJ 04DIAMETER ACCOMMODATED,FACE FACE DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR A FACE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARHGD 14SHAPE,CROSS-SECTIONAL,HEAD HEAD CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE HEAD WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 ARHHJ /D/ 04LENGTH,FACE FACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A FACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARHJD /D/ 07FACE,HERMISPHERICAL HERMISPHERICAL FACE AN INDICATION OF WHETHER OR NOT A HEMISPHERICAL FACE IS INCLUDED. SELECT REPLY CODE 10AA49 ARHKD /D/ 07HAMMER HAMMER AN INDICATION OF WHETHER OR NOT A HAMMER IS INCLUDED. SELECT REPLY CODE 10AA49 ARHLJ 04WIDTH ACCOMMODATED,CROWN,STAPLE STAPLE CROWN WIDTH ACCOMMODATED THE WIDTH OF THE STAPLE CROWN THE ITEM IS DESIGNED TO ACCOMMODATE. 2D AND 1B MODE REPLY21AA051AC20 ARHMD 11METHOD,FEED,BURNER FUEL BURNER FUEL FEED METHOD THE MEANS USED TO FEED FUEL TO THE BURNER. SELECT REPLY CODE 10AL50 ARHND /D/ 07TANK,FUEL,INTEGRAL INTEGRAL FUEL TANK AN INDICATION OF WHETHER OR NOT AN INTEGRAL FUEL TANK IS INCLUDED. SELECT REPLY CODE 10AA49 ARHPB /D/ 10DELIVERY RATE IN BTU PER HOUR,HEAT,DUCT DUCT HEAT DELIVERY RATE IN BTU PER HOUR THE MAXIMUM HEAT SUPPLIED TO THE DUCTS,EXPRESSED IN BRITISH THERMAL UNITS PER HOUR. 1B MODE REPLY 0 ARHQB /D/ 10DELIVERY RATE IN BTU PER HOUR,HEAT,COOLANT COOLANT HEAT DELIVERY RATE IN BTU PER HOUR THE MAXIMUM HEAT SUPPLIED TO THE COOLANT,EXPRESSED IN BRITISH THERMAL UNITS PER HOUR. 1B MODE REPLY 0 ARHRD /D/ 07SWITCH,HEATER,MOUNTED MOUNTED HEATER SWITCH AN INDICATION OF WHETHER OR NOT A MOUNTED HEATER SWITCH IS INCLUDED. SELECT REPLY CODE 10AA49 ARHSD /D/ 07CONTROL,TEMP,AUTOMATIC AUTOMATIC TEMP CONTROL INDICATES WHETHER OR NOT AN AUTOMATIC TEMPERATURE CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 ARHTA 12QUANTITY,CONNECTION,AIR DUCT AIR DUCT CONNECTION QUANTITY THE NUMBER OF CONNECTIONS PROVIDED ON THE AIR DUCT. 1A MODE REPLY 0 ARHWD 02DESIGN,CONNECTION,AIR DUCT AIR DUCT CONNECTION DESIGN THE DESIGN OF THE AIR DUCT CONNECTION. SELECT REPLY CODE 10AD07 ARHXD 18TYPE,CONNECTION,ANGLE ANGLE CONNECTION TYPE INDICATES THE TYPE OF ANGLE CONNECTION(S) INCLUDED ON THE ITEM. SELECT REPLY CODE 10AL49 ARHYD /D/ 07PROVISION,THREAD,AIR DUCT CONNECTION AIR DUCT CONNECTION THREAD PROVISION AN INDICATION OF WHETHER OR NOT A CONNECTION THREAD PROVISION FOR THE AIR DUCT IS INCLUDED. SELECT REPLY CODE 10AA49 ARHZD 19SOURCE FOR WHICH DESIGNED,POWER POWER SOURCE FOR WHICH DESIGNED AN INDICATION OF THE POWER SOURCE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AH00 ARJAJ 10PRESSURE RATING PRESSURE RATING THE PRESSURE AT WHICH AN ITEM IS RATED TO OPERATE. 1D AND 1B MODE REPLY11AB18 ARJBB 10WATTAGE,ELEMENT,HEATING HEATING ELEMENT WATTAGE THE RATED POWER THAT THE HEATING ELEMENT CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS. 1B MODE REPLY 0 ARJCD 11METHOD,CIRCULATION,COOLANT COOLANT CIRCULATION METHOD THE MEANS USED FOR CIRCULATING THE COOLANT. SELECT REPLY CODE 10AL51 ARJDD 19FORM,DESIGN DESIGN FORM THE PHYSICAL CONFIGURATION OF THE ITEM. SELECT REPLY CODE 10AL52 ARJED /D/ 07CAP,FILLER FILLER CAP AN INDICATION OF WHETHER OR NOT A FILLER CAP IS INCLUDED. SELECT REPLY CODE 10AA49 ARJFD /D/ 07FEATURE,COMPRESSION,LONGITUDINAL LONGITUDINAL COMPRESSION FEATURE AN INDICATION OF WHETHER OR NOT A LONGITUDINAL COMPRESSION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARJGD 19ABSORBENCY RATING,WATER WATER ABSORBENCY RATING AN INDICATION OF THE WATER ABSORBENCY RATE OF THE ITEM. SELECT REPLY CODE 10AH10 ARJHD /D/ 07FEATURE,RESISTANT,FLAME FLAME RESISTANT FEATURE AN INDICATION OF WHETHER OR NOT A FLAME RESISTANT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARJJD /D/ 07FEATURE,RESISTANT,FUNGUS FUNGUS RESISTANT FEATURE AN INDICATION OF WHETHER OR NOT A FUNGUS RESISTANT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARJKD 18TYPE,TIP,CLEANING CLEANING TIP TYPE INDICATES THE TYPE OF CLEANING TIP PROVIDED. SELECT REPLY CODE 10AK84 ARJLA /D/ 16STYLE DESIGNATOR,TIP,CLEANING CLEANING TIP STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CLEANING TIP. 1A MODE REPLY 0 ARJMD 11METHOD,ATTACHMENT,CLEANING TIP CLEANING TIP ATTACHMENT METHOD THE MEANS OF ATTACHING THE CLEANING TIP TO THE ITEM. SELECT REPLY CODE 10AE44 ARJNA 03DESIGNATOR,THREAD THREAD DESIGNATOR DESIGNATES THE THREAD DIAMETER,CLASS,SERIES/TYPE AND QUANTITY OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1A MODE REPLY 0 ARJPJ /D/ 04DIAMETER,INSIDE,INTERNAL RELIEF INTERNAL RELIEF INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE PASSING THROUGH THE CENTER OF THE INTERNAL RELIEF,WITH TERMINATED POINTS ON THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARJQJ /D/ 04LENGTH,RELIEF,INTERNAL INTERNAL RELIEF LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE INTERNAL RELIEF,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARJRA 12QUANTITY,PLY,DRESSING DRESSING PLY QUANTITY THE NUMBER OF PLIES CONTAINED IN A DRESSING. 1A MODE REPLY 0 ARJSD 19STRUCTURE,DRESSING DRESSING STRUCTURE AN INDICATION OF THE STRUCTURE OF THE DRESSING. SELECT REPLY CODE 10AL53 ARJTD /D/ 07DYE,CAMOUFLAGE CAMOUFLAGE DYE AN INDICATION OF WHETHER OR NOT CAMOUFLAGE DYE IS INCLUDED. SELECT REPLY CODE 10AA49 ARJWJ 04LENGTH,FORMED FORMED LENGTH A MEASUREMENT OF THE LONGEST,OR LONGER,DIMENSION OF THE FINAL SHAPE TAKEN AS A UNIT OF MEASURE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARJXJ 04WIDTH,FORMED FORMED WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE MEASURED LENGTH OF THE FINAL SHAPE TAKEN AS A UNIT OF MEASURE,IN DISTINCTION FROM THE THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ARJYJ /D/ 04LENGTH,OVERALL,BELT BELT OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BELT. 2D AND 1B MODE REPLY21AA051AC20 ARJZJ 04LENGTH,STRAP STRAP LENGTH A MEASUREMENT OF THE LONGEST,OR LONGER,DIMENSION OF THE STRAP TAKEN AS A UNIT OF MEASURE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARKAJ 04WIDTH,STRAP STRAP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A STRAP,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ARKBJ /D/ 04LENGTH,TIE TIE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARKCJ /D/ 04WIDTH,TIE TIE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE MEASURED LENGTH OF THE TIE TAKEN AS A UNIT OF MEASURE,IN DISTINCTION FROM THICKNESS. . 2D AND 1B MODE REPLY21AA051AC20 ARKDJ /D/ 04LENGTH,WRIST WRIST LENGTH A MEASUREMENT OF THE LONGEST,OR LONGER,DIMENSION OF A WRIST TAKEN AS A UNIT OF MEASURE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARKEJ 04LENGTH,BANDAGE BANDAGE LENGTH A MEASUREMENT OF THE LONGEST,OR LONGER,DIMENSION OF A BANDAGE TAKEN AS A UNIT OF MEASURE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARKFJ 04WIDTH,BANDAGE BANDAGE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE MEASURED LENGTH OF THE BANDAGE TAKEN AS A UNIT OF MEASURE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ARKGJ /D/ 04LENGTH,COMPRESS COMPRESS LENGTH A MEASUREMENT OF THE LONGEST,OR LONGER,DIMENSION OF A COMPRESS TAKEN AS A UNIT OF MEASURE,IN DISTINCTION FROM WIDTH. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 ARKHD /D/ 07COIL,BOOSTER BOOSTER COIL AN INDICATION OF WHETHER OR NOT A BOOSTER COIL IS INCLUDED. SELECT REPLY CODE 10AA49 ARKJD /D/ 07FEATURE,MOUNTING,STANDARD STANDARD MOUNTING FEATURE AN INDICATION OF WHETHER OR NOT A STANDARD MOUNTING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARKKD /D/ 19SOURCE,STANDARD,MOUNTING MOUNTING STANDARD SOURCE THE NAME OF THE GOVERNMENT AGENCY,COMMERCIAL ORGANIZATION,OR MANUFACTURER CONTROLLING THE STANDARD MOUNTING. SELECT REPLY CODE 10AF94 ARKLA /D/ 19NUMBER,IDENTIFYING,MOUNTING STANDARD MOUNTING STANDARD IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE MOUNTING STANDARD. 1A MODE REPLY 0 ARKMD /D/ 11METHOD,MOUNTING,STANDARD STANDARD MOUNTING METHOD THE STANDARD MECHANICAL MEANS OF ATTACHING THE ITEM. SELECT REPLY CODE 10AB89 ARKND 14SHAPE,FLANGE FLANGE SHAPE THE PHYSICAL CONFIGURATION OF THE FLANGE. SELECT REPLY CODE 10AD07 ARKPJ /D/A18TYPE AND QUANTITY,FACILITY,MOUNTING MOUNTING FACILITY TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF FACILITIES BY WHICH THE ITEM IS MOUNTED. 1D AND 1A MODE REPLY13AB89 ARKQG /D/ 04SPACING,FACILITY,MOUNTING MOUNTING FACILITY SPACING THE DISTANCE BETWEEN THE MOUNTING FACILITIES. FULL TEXT WRITE-IN 0 ARKRD 08LOCATION,COLOR COLOR LOCATION INDICATES THE LOCATION OF AN ITEM TO WHICH THE COLOR IS APPLIED. SELECT REPLY CODE 10AJ91 ARKSG /D/ 19DIMENSION,SLOT,MOUNTING MOUNTING SLOT DIMENSION DESIGNATES THE DIMENSIONS OF THE MOUNTING SLOT. FULL TEXT WRITE-IN 0 ARKTG /D/ 04DIAMETER,CIRCLE,BOLT,MOUNTING MOUNTING BOLT CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE PASSING THROUGH THE CENTER OF A MOUNTING BOLT CIRCLE,WITH TERMINATED POINTS AT THE CIRCUMFERENCE. FULL TEXT WRITE-IN 0 ARKWG /D/ 04SIZE,HOLE,FLYWHEEL MOUNTING FLYWHEEL MOUNTING HOLE SIZE THE SIZE OF THE HOLE PROVIDED FOR MOUNTING A FLYWHEEL. FULL TEXT WRITE-IN 0 ARKXJ /D/A18TYPE AND QUANTITY,FACILITY,MOUNTING,BREAKER PLATE BREAKER PLATE MOUNTING FACILITY TYPE AND QUANTITY THE MEANS BY WHICH THE BREAKER PLATE IS MOUNTED AND THE QUANTITY. 1D AND 1A MODE REPLY13AB89 ARKYG /D/ 04DIAMETER,CIRCLE,BOLT,BREAKER PLATE MOUNTING BREAKER PLATE MOUNTING BOLT CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE PASSING THROUGH THE CENTER OF A BREAKER PLATE MOUNTING BOLT CIRCLE,WITH TERMINATED POINTS AT THE CIRCUMFERENCE. FULL TEXT WRITE-IN 0 ARKZJ /D/ 04DIAMETER,HOLE,BREAKER PLATE MOUNTING BREAKER PLATE MOUNTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE PASSING THROUGH THE CENTER OF A BREAKER PLATE MOUNTING HOLE,AND TERMINATING AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARLAG /D/ 19DIMENSION,SLOT,MOUNTING,BREAKER PLATE BREAKER PLATE MOUNTING SLOT DIMENSION DESIGNATES THE DIMENSIONS OF THE BREAKER PLATE MOUNTING SLOT. FULL TEXT WRITE-IN 0 ARLBD /D/ 07FEATURE,MOUNTED,CLAMP CLAMP MOUNTED FEATURE AN INDICATION OF WHETHER OR NOT A CLAMP MOUNTED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARLCD 02DESIGN,ELECTRODE ELECTRODE DESIGN THE DESIGN OF THE ELECTRODE. SELECT REPLY CODE 10AB03 ARLDA 12QUANTITY,ACCOMMODATION,SPARK PLUG LEAD SPARK PLUG LEAD ACCOMMODATION QUANTITY THE NUMBER OF SPARK PLUG LEAD ACCOMMODATIONS PROVIDED. 1A MODE REPLY 0 ARLED 19POSITION,ACCOMMODATION,SPARK PLUG LEAD SPARK PLUG LEAD ACCOMMODATION POSITION THE POSITION OF THE SPARK PLUG LEAD ACCOMMODATION WHEN THE MOUNTING BASE IS IN A HORIZONTAL POSITION. SELECT REPLY CODE 10AC60 ARLFA 12QUANTITY,ACCOMMODATION,EXTERNAL COIL LEAD EXTERNAL COIL LEAD ACCOMMODATION QUANTITY THE NUMBER OF EXTERNAL COIL LEAD ACCOMMODATIONS INCLUDED. 1A MODE REPLY 0 ARLGD 19POSITION,ACCOMMODATION,COIL LEAD COIL LEAD ACCOMMODATION POSITION THE POSITION OF THE COIL LEAD ACCOMMODATION WHEN THE MOUNTING BASE IS IN A HORIZONTAL POSITION. SELECT REPLY CODE 10AC60 ARLHD 18TYPE,ELECTRODE,COIL,INTERNAL INTERNAL COIL ELECTRODE TYPE INDICATES THE TYPE OF INTERNAL COIL ELECTRODE(S) INCLUDED. SELECT REPLY CODE 10AG81 ARLJD /D/ 07ACCOMMODATION,ELECTRODE,SPRING LOADED BRUSH TYPE SPRING LOADED BRUSH TYPE ELECTRODE ACCOMMODATION AN INDICATION OF WHETHER OR NOT AN ACCOMMODATION/S/ IS INCLUDED FOR A SPRING LOADED BRUSH TYPE ELECTRODE/S/. SELECT REPLY CODE 10AA49 ARLKD /D/ 07ACCOMMODATION,COVER COVER ACCOMMODATION AN INDICATION OF WHETHER OR NOT ACCOMMODATIONS FOR A COVER ARE INCLUDED. SELECT REPLY CODE 10AA49 ARLLD 18TYPE,CONTACT,INLET INLET CONTACT TYPE THE TYPE OF INLET CONTACT(S) ON THE ITEM. SELECT REPLY CODE 10AG81 ARLMJ 04DISTANCE BETWEEN INLET CONTACT AND DISTRIBUTING CONTACT,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN INLET CONTACT AND DISTRIBUTING CONTACT THE DISTANCE MEASURED FROM THE CENTER OF THE INLET CONTACT TO THE CENTER OF THE DISTRIBUTING CONTACT. 2D AND 1B MODE REPLY21AA051AC20 ARLNJ 04DISTANCE FROM INLET CONTACT CENTER TO DISTRIBUTING CONTACT END DISTANCE FROM INLET CONTACT CENTER TO DISTRIBUTING CONTACT END THE DISTANCE MEASURED FROM THE CENTER OF THE INLET CONTACT TO THE END OF THE DISTRIBUTING CONTACT. 2D AND 1B MODE REPLY21AA051AC20 ARLPA 12QUANTITY,CONTACT,DISTRIBUTING DISTRIBUTING CONTACT QUANTITY THE NUMBER OF CONTACTS PROVIDED FOR ELECTRICAL ENERGY TRANSFER FROM THE ITEM. 1A MODE REPLY 0 ARLQB 04ANGLE BETWEEN DISTRIBUTING CONTACTS IN DEG ANGLE BETWEEN DISTRIBUTING CONTACTS IN DEG THE ANGULAR MEASUREMENT BETWEEN CONTACTS. 1B MODE REPLY 0 ARLRD 08LOCATION,CONTACT,DISTRIBUTING DISTRIBUTING CONTACT LOCATION INDICATES THE LOCATION OF THE DISTRIBUTING CONTACT/S/ ON THE ITEM. SELECT REPLY CODE 10AJ91 ARLSJ 04DISTANCE BETWEEN PLANES DISTANCE BETWEEN PLANES THE DISTANCE BETWEEN PLANES ON THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ARLTD 14SHAPE FOR WHICH DESIGNED,SHAFT SHAFT SHAPE FOR WHICH DESIGNED THE PHYSICAL CONFIGURATION OF THE SHAFT SHAPE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AD07 ARLWD /D/ 07FEATURE,SEPARABILITY,POLE PIECE POLE PIECE SEPARABILITY FEATURE AN INDICATION OF WHETHER OR NOT A POLE PIECE SEPARABILITY FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARLXJ 10VOLTAGE RATING,PRIMARY,DC DC PRIMARY VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,OF DIRECT CURRENT PRIMARY POTENTIAL FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY21AB631AC20 ARLYD /D/ 18TYPE,TERMINAL,HIGH VOLTAGE HIGH VOLTAGE TERMINAL TYPE INDICATES THE TYPE OF HIGH VOLTAGE TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. SELECT REPLY CODE 10AA58 ARLZA 12QUANTITY,TERMINAL,HIGH VOLTAGE HIGH VOLTAGE TERMINAL QUANTITY THE NUMBER OF TERMINALS FOR PROVIDING HIGH VOLTAGE ELECTRICAL CONNECTION TO THE ITEM. 1A MODE REPLY 0 ARMAD /D/ 18TYPE,TERMINAL,LOW VOLTAGE LOW VOLTAGE TERMINAL TYPE THE SPECIFIC TYPE OF LOW VOLTAGE TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. SELECT REPLY CODE 10AA58 ARMBA 12QUANTITY,TERMINAL,LOW VOLTAGE LOW VOLTAGE TERMINAL QUANTITY THE NUMBER OF TERMINALS FOR PROVIDING LOW VOLTAGE ELECTRICAL CONNECTION TO THE ITEM. 1A MODE REPLY 0 ARMCJ /D/ 04WIDTH,SHAFT,SQUARE SQUARE SHAFT WIDTH NONE. 3D AND 1B MODE REPLY31AA051AC202AD87 ARMDJ /D/ 04WIDTH,COMPRESS COMPRESS WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE MEASURED LENGTH OF THE COMPRESS TAKEN AS A UNIT OF MEASURE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ARMEJ 04LENGTH,PAD PAD LENGTH A MEASUREMENT OF THE LONGEST,OR LONGER,DIMENSION OF A PAD TAKEN AS A UNIT OF MEASURE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARMFJ 04WIDTH,PAD PAD WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE MEASURED LENGTH OF A PAD TAKEN AS A UNIT OF MEASURE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ARMGJ /D/ 04LENGTH,SKULLCAP,SURGICAL SURGICAL SKULLCAP LENGTH AMEASUREMENT OF THE LONGEST,OR LONGER,DIMENSION OF A SURGICAL SKULLCAP TAKEN AS A UNIT OF MEASURE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARMHJ /D/ 04WIDTH,SKULLCAP,SURGICAL SURGICAL SKULLCAP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE MEASURED LENGTH OF A SURGICAL SKULLCAP TAKEN AS A UNIT OF MEASURE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ARMJA 12QUANTITY,DEVICE,SECURING SECURING DEVICE QUANTITY THE NUMBER OF DEVICES USED TO SECURE THE ITEM. 1A MODE REPLY 0 ARMKD /D/ 19COMPOSITION,ADHESIVE ADHESIVE COMPOSITION AN INDICATION OF THE ADHESIVE COMPOSITION THAT MAKES UP THE ITEM. SELECT REPLY CODE 10AL54 ARMLD /D/ 07FEATURE,PERFORATION PERFORATION FEATURE AN INDICATION OF WHETHER OR NOT A PERFORATION FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 ARMMD /D/ 07COATING,ADHESIVE ADHESIVE COATING AN INDICATION OF WHETHER OR NOT AN ADHESIVE COATING IS INCLUDED. SELECT REPLY CODE 10AA49 ARMNJ /D/ 04LENGTH,LEG,TRIANGLE TRIANGLE LEG LENGTH A MEASUREMENT OF THE LONGEST,OR LONGER,DIMENSION OF A TRIANGLE LEG TAKEN AS A UNIT OF MEASURE,IN DISTINCTION FROM THICKNESS. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 3D AND 1B MODE REPLY31AA051AC202AL55 ARMPJ A10TIME,SETTING SETTING TIME THE LENGTH OF TIME REQUIRED FOR THE ITEM TO SET. 2D AND 1A MODE REPLY22AH681AC20 ARMQA /D/ 12QUANTITY,BANDAGE,SUPPORTING SUPPORTING BANDAGE QUANTITY THE NUMBER OF SUPPORTING BANDAGES USED WITH THE ITEM. 1A MODE REPLY 0 ARMRD /D/ 07IMPREGNATED,PAD PAD IMPREGNATED AN INDICATION OF WHETHER OR NOT AN IMPREGNATED PAD IS INCLUDED. SELECT REPLY CODE 10AA49 ARMSD /D/ 14SHAPE,STRIP,PLASTIC ADHESIVE PLASTIC ADHESIVE STRIP SHAPE THE PHYSICAL CONFIGURATION OF THE PLASTIC ADHESIVE STRIP. SELECT REPLY CODE 10AD07 ARMTJ /D/ 04SPACING,EYELET EYELET SPACING THE SPACING FROM THE CENTER OF ONE EYELET TO THE CENTER OF THE NEXT EYELET. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 ARMWD /D/ 07FEATURE,SEALED IN TUBE SEALED IN TUBE FEATURE AN INDICATION OF WHETHER OR NOT A SEALED IN TUBE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARMXD /D/ 07FEATURE,SELF-ADHERING SELF-ADHERING FEATURE AN INDICATION OF WHETHER OR NOT A SELF-ADHERING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARMYD /D/ 19COUNT PER INCH,THREAD,MATERIAL MATERIAL THREAD COUNT PER INCH THE NUMBER OF WARP THREADS /LENGTHWISE/ AND FILL THREADS /CROSSWISE/ PER INCH OF MATERIAL. SELECT REPLY CODE 10AL56 ARMZG /D/ 10WEIGHT PER DOZEN WEIGHT PER DOZEN A RELATIVE MEASURE OF THE MASS PER DOZEN WITH RESPECT TO ITS DENSITY. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. FULL TEXT WRITE-IN 0 ARNAD 18TYPE,COOLANT COOLANT TYPE INDICATES THE TYPE OF COOLANT USED WITH THE ITEM. SELECT REPLY CODE 10AL57 ARNBD /D/ 18TYPE,BINDER BINDER TYPE AN INDICATION OF THE TYPE OF BINDER PROVIDED. SELECT REPLY CODE 10AB60 ARNCJ 10WEIGHT IN POUNDS,SUBSTANCE SUBSTANCE WEIGHT IN POUNDS THE MEASURED SUBSTANCE WEIGHT IN POUNDS. 1D AND 1B MODE REPLY12AG45 ARNDD 02DESIGN,MUFFLER MUFFLER DESIGN THE BASIC DESIGN OF THE MUFFLER. SELECT REPLY CODE 10AL58 ARNEA 12QUANTITY,BAFFLE BAFFLE QUANTITY THE NUMBER OF BAFFLES INCLUDED ON THE ITEM. 1A MODE REPLY 0 ARNFA 12QUANTITY,TUBE TUBE QUANTITY THE NUMBER OF TUBES INCLUDED ON THE ITEM. 1A MODE REPLY 0 ARNGD 14SHAPE,BODY BODY SHAPE THE PHYSICAL CONFIGURATION OF THE BODY. SELECT REPLY CODE 10AD07 ARNHD 19POSITION,OPERATING OPERATING POSITION THE POSITION IN WHICH THE ITEM IS DESIGNED TO OPERATE. SELECT REPLY CODE 10AF63 ARNJG 08LOCATION,INLET INLET LOCATION THE LOCATION OF THE INLET. FULL TEXT WRITE-IN 0 ARNKJ 04LENGTH,PROJECTION,INLET INLET PROJECTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE INLET PROJECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARNLD 14SHAPE,FLANGE,INLET INLET FLANGE SHAPE THE PHYSICAL CONFIGURATION OF THE INLET FLANGE. SELECT REPLY CODE 10AD07 ARNMJ A19PROVISION AND QUANTITY,MOUNTING,INLET FLANGE INLET FLANGE MOUNTING PROVISION AND QUANTITY THE TYPE AND NUMBER OF INLET FLANGE MOUNTING PROVISIONS PROVIDED. 1D AND 1A MODE REPLY12AB89 ARNNJ 04DIAMETER,HOLE,INLET FLANGE MOUNTING INLET FLANGE MOUNTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE PASSING THROUGH THE CENTER OF AN INLET FLANGE MOUNTING HOLE,AND TERMINATING AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARNPJ 04LENGTH,STUD,MOUNTING,INLET FLANGE INLET FLANGE MOUNTING STUD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN INLET FLANGE MOUNTING STUD,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARNQA /D/ 13THREAD SIZE,PROVISION,INLET FLANGE MOUNTING INLET FLANGE MOUNTING PROVISION THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE INLET FLANGE MOUNTING PROVISION. 1A MODE REPLY 0 ARNRD 13THREAD SERIES DESIGNATOR,PROVISION,INLET FLANGE MOUNTING INLET FLANGE MOUNTING PROVISION THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF AN INLET FLANGE MOUNTING PROVISION. SELECT REPLY CODE 10AH06 ARNSD 13THREAD DIRECTION,PROVISION,INLET FLANGE MOUNTING INLET FLANGE MOUNTING PROVISION THREAD DIRECTION THE DIRECTION OF THE INLET FLANGE MOUNTING PROVISION THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ARNTG /D/ 04SPACING,PROVISION,INLET FLANGE MOUNTING INLET FLANGE MOUNTING PROVISION SPACING THE SPACING OF THE INLET FLANGE MOUNTING PROVISION. FULL TEXT WRITE-IN 0 ARNWA 13THREAD SIZE,INLET INLET THREAD SIZE DESIGNATES THE THREAD DIAMETER AND QUANTITY OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1A MODE REPLY 0 ARNXD 13THREAD SERIES DESIGNATOR,INLET INLET THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF AN INLET. SELECT REPLY CODE 10AH06 ARNYD /D/ 07TERMINAL,GROUND GROUND TERMINAL AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A GROUND TERMINAL. SELECT REPLY CODE 10AB22 ARNZD 07ADJUSTABILITY,VIBRATOR VIBRATOR ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE VIBRATOR IS ADJUSTABLE. SELECT REPLY CODE 10AB00 ARPAD 19MEDIUM,FILLING FILLING MEDIUM THE SUBSTANCE WITH WHICH THE ITEM IS FILLED. SELECT REPLY CODE 10AK06 ARPBD 18TYPE,ACCOMMODATION ACCOMMODATION TYPE THE TYPE OF ACCOMMODATION PROVIDED. SELECT REPLY CODE 10AE15 ARPCD 07REMOVABILITY,MOUNTING MOUNTING REMOVABILITY AN INDICATION OF WHETHER OR NOT THE MOUNTING IS REMOVABLE. SELECT REPLY CODE 10AC29 ARPDA 12QUANTITY,TURN,PRIMARY WINDING PRIMARY WINDING TURN QUANTITY THE NUMBER OF INDIVIDUAL PRIMARY WINDING TURNS. 1A MODE REPLY 0 ARPEA 04SIZE,AWG,PRIMARY WINDING PRIMARY WINDING AWG SIZE THE AMERICAN WIRE GAGE SIZE OF THE PRIMARY WINDING. 1A MODE REPLY 0 ARPFA 12QUANTITY,TURN,SECONDARY WINDING SECONDARY WINDING TURN QUANTITY THE NUMBER OF INDIVIDUAL SECONDARY WINDING TURNS. 1A MODE REPLY 0 ARPGA 04SIZE,AWG,SECONDARY WINDING SECONDARY WINDING AWG SIZE THE AMERICAN WIRE GAGE SIZE OF THE SECONDARY WINDING. 1A MODE REPLY 0 ARPHD /D/ 18TYPE,TERMINAL,PRIMARY PRIMARY TERMINAL TYPE INDICATES THE TYPE OF PRIMARY TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. SELECT REPLY CODE 10AA58 ARPJA 12QUANTITY,TERMINAL,PRIMARY PRIMARY TERMINAL QUANTITY THE NUMBER OF PRIMARY TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. 1A MODE REPLY 0 ARPKD /D/ 18TYPE,TERMINAL,SECONDARY SECONDARY TERMINAL TYPE INDICATES THE TYPE OF SECONDARY TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. SELECT REPLY CODE 10AA58 ARPLA 12QUANTITY,TERMINAL,SECONDARY SECONDARY TERMINAL QUANTITY THE NUMBER OF SECONDARY TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. 1A MODE REPLY 0 ARPMD /D/ 07CORE CORE AN INDICATION OF WHETHER OR NOT A CORE IS INCLUDED. SELECT REPLY CODE 10AA49 ARPNJ 04HEIGHT,CORE CORE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE CORE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 ARPPD /D/ 09MATERIAL,INSULATION,EXTERIOR EXTERIOR INSULATION MATERIAL THE COMPOSITION OF WHICH THE EXTERIOR INSULATION IS FABRICATED. SELECT REPLY CODE 10AD09 ARPQJ /D/ 10VOLTAGE RATING,NO LOAD,DC DC NO LOAD VOLTAGE RATING THE NO LOAD VALUE OF DC POTENTIAL FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY21AB631AC20 ARPRJ /D/ 10CURRENT RATING,DC,NO LOAD MAXIMUM NO LOAD MAXIMUM DC CURRENT RATING THE NO LOAD MAXIMUM DIRECT CURRENT FOR WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY11AC30 ARPSB /D/ 10RPM,MINIMUM,DC NO LOAD DC NO LOAD MINIMUM RPM THE DIRECT CURRENT NO LOAD MINIMUM REVOLUTIONS PER MINUTE FOR WHICH THE ITEM IS RATED. 1B MODE REPLY 0 ARPTJ /D/ 10VOLTAGE RATING,ARMATURE,LOCKED,DC DC LOCKED ARMATURE VOLTAGE RATING THE LOCKED ARMATURE VALUE OF THE DC POTENTIAL FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY21AB631AC20 ARPWJ /D/ 10CURRENT RATING,DC,LOCKED ARMATURE MAXIMUM LOCKED ARMATURE MAXIMUM DC CURRENT RATING THE LOCKED ARMATURE MAXIMUM DC CURRENT FOR WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY11AC30 ARPXJ /D/ 10TORQUE RATING,MINIMUM,DC LOCKED ARMATURE DC LOCKED ARMATURE MINIMUM TORQUE RATING THE DIRECT CURRENT LOCKED ARMATURE MINIMUM TORQUE FOR WHICH THE ITEM IS RATED. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1D AND 1B MODE REPLY11AA56 ARPYD /D/ 05DIRECTION,ROTATION,ARMATURE ARMATURE ROTATION DIRECTION THE DIRECTION OF ROTATION OF THE ARMATURE AS VIEWED FROM THE DRIVE END. SELECT REPLY CODE 10AA38 ARPZJ /D/ 04DIAMETER,OUTSIDE,SHAFT SHAFT OUTSIDE DIAMETER THE LENGTH OF THE CHORD WHICH PASSES THROUGH THE CENTER OF THE SHAFT IN PLAN VIEW AND TERMINATES AT THE OUTER PERIPHERY. 2D AND 1B MODE REPLY21AA051AC20 ARQAJ 04LENGTH,PROTRUSION,SHAFT SHAFT PROTRUSION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION THE SHAFT EXTENDS FROM THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ARQBJ /D/ 04DIAMETER,SURFACE,EXTERNAL BEARING EXTERNAL BEARING SURFACE DIAMETER THE LENGTH OF A STRAIGHT LINE PASSING THROUGH THE CENTER OF THE EXTERNAL BEARING SURFACE,AND TERMINATING AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARQCJ /D/ 04LENGTH,SURFACE,BEARING,EXTERNAL EXTERNAL BEARING SURFACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE EXTERNAL BEARING SURFACE TAKEN PARALLEL TO THE SHAFT AXIS. 2D AND 1B MODE REPLY21AA051AC20 ARQDD /D/ 14SHAPE,SHAFT,SPLINED SPLINED SHAFT SHAPE THE PHYSICAL CONFIGURATION OF THE SPLINED SHAFT. SELECT REPLY CODE 10AD07 ARQEJ 10POWER RATING,ELECTRIC ELECTRIC POWER RATING THE VALUE OF ELECTRICAL ENERGY FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY21AC331AC20 ARQFD 19CHARACTERISTIC,STARTING STARTING CHARACTERISTIC THE STARTING CHARACTERISTIC OF THE ITEM. SELECT REPLY CODE 10AE56 ARQGD 07STARTER STARTER AN INDICATION OF WHETHER OR NOT A STARTER IS REQUIRED. SELECT REPLY CODE 10AE40 ARQHJ A08LOCATION AND QUANTITY,TERMINAL TERMINAL LOCATION AND QUANTITY THE POSITION AND QUANTITY OF TERMINALS FOR MAKING CONNECTION TO THE ITEM. 1D AND 1A MODE REPLY13AJ91 ARQJD 18TYPE,CURRENT,LAMP LAMP CURRENT TYPE THE TYPE OF CURRENT FOR WHICH THE LAMP IS DESIGNED. SELECT REPLY CODE 10AB62 ARQKJ 10VOLTAGE RATING IN VOLTS,LAMP LAMP VOLTAGE RATING IN VOLTS THE TOTAL ELECTRICAL VOLTAGE OF THE LAMP,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 ARQLA 12QUANTITY,BRUSH,EXTRA EXTRA BRUSH QUANTITY THE NUMBER OF EXTRA BRUSHES FURNISHED WITH THE ITEM. 1A MODE REPLY 0 ARQMA 12QUANTITY,SLOT,MOUNTING MOUNTING SLOT QUANTITY THE QUANTITY OF MOUNTING SLOTS PROVIDED. 1A MODE REPLY 0 ARQND 18TYPE,STARTER STARTER TYPE THE TYPE OF STARTER PROVIDED. SELECT REPLY CODE 10AD48 ARQPD /D/ 07PROVISION,LOCKOUT LOCKOUT PROVISION AN INDICATION OF WHETHER OR NOT A LOCKOUT PROVISION IS INCLUDED. SELECT REPLY CODE 10AA49 ARQQD 11METHOD,RESET,LOCKOUT LOCKOUT RESET METHOD AN INDICATION OF THE MEANS USED TO RESET THE LOCKOUT. SELECT REPLY CODE 10AC58 ARQRD /D/ 07SURFACE,REFLECTING,CORRUGATED CORRUGATED REFLECTING SURFACE AN INDICATION OF WHETHER OR NOT A CORRUGATED REFLECTING SURFACE IS INCLUDED. SELECT REPLY CODE 10AA49 ARQSD /D/ 19CONSTRUCTION CONSTRUCTION THE STRUCTURAL CHARACTERISTIC OF THE ITEM. PLEASE USE MRC CQCF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AL59 ARQTD 08LOCATION,OPENING OPENING LOCATION THE LOCATION OF THE OPENING ON THE ITEM. SELECT REPLY CODE 10AJ91 ARQWD /D/ 07REFLECTOR REFLECTOR AN INDICATION OF WHETHER OR NOT A REFLECTOR IS INCLUDED. SELECT REPLY CODE 10AA49 ARQXD /D/ 07HOOK HOOK AN INDICATION OF WHETHER OR NOT A HOOK IS INCLUDED. SELECT REPLY CODE 10AA49 ARQYD 02DESIGN,LOUVER LOUVER DESIGN THE DESIGN OF THE LOUVER. SELECT REPLY CODE 10AK54 ARQZD 08LOCATION,OPENING,LAMPHOLDER LAMPHOLDER OPENING LOCATION INDICATES THE LOCATION OF THE LAMPHOLDER OPENING ON THE ITEM. SELECT REPLY CODE 10AJ91 ARRAG /D/ 04DIMENSION,OPENING,LAMPHOLDER LAMPHOLDER OPENING DIMENSION THE DIMENSION/S/ OF THE LAMPHOLDER OPENING. FULL TEXT WRITE-IN 0 ARRBD /D/ 17SURFACE TREATMENT,ACCESSORY ACCESSORY SURFACE TREATMENT THE COATING,DIP,AND/OR PLATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE ACCESSORY SURFACE. SELECT REPLY CODE 10AD09 ARRCD /D/ 09MATERIAL,ACCESSORY ACCESSORY MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ACCESSORY IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ARRDJ 10WEIGHT AND LOCATION,BASIS,NOMINAL NOMINAL BASIS WEIGHT AND LOCATION THE PAPER WEIGHT BASED ON A GIVEN QUANTITY OF SHEETS OF A SPECIFIED SIZE OR BASED ON A SPECIFIED SQUARE AREA AND ITS LOCATION. 2D AND 1B MODE REPLY23AL623AJ91 ARREJ 10WEIGHT AND LOCATION,TEXTILE,NOMINAL NOMINAL TEXTILE WEIGHT AND LOCATION THE NOMINAL WEIGHT OF THE TEXTILE AND ITS LOCATION. 2D AND 1B MODE REPLY22AG693AJ91 ARRFJ /D/ 04THICKNESS AND LOCATION,MATERIAL,NOMINAL NOMINAL MATERIAL THICKNESS AND LOCATION THE NOMINAL MEASUREMENT BETWEEN TWO PLANE SURFACES OF THE MATERIAL AS DISTINGUISHED FROM LENGTH OR WIDTH,AND ITS LOCATION. PLEASE USE MRC AAVY WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA053AJ91 ARRGJ /D/ 10CAPACITY,LOAD LOAD CAPACITY THE RATED LOAD THAT THE ITEM WILL ACCOMMODATE. PLEASE USE MRC BQLQ IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1B MODE REPLY11AB10 ARRHJ 10CAPACITY,LIQUID LIQUID CAPACITY THE VALUE WHICH REFLECTS THE AMOUNT OF LIQUID THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY11AB10 ARRJJ A19DEVICE AND QUANTITY,HANDLING HANDLING DEVICE AND QUANTITY THE PROVISION(S) INCLUDED IN THE DESIGN OF THE ITEM TO FACILITATE CARRYING,TRANSPORTING,OR LIFTING AND THE NUMBER OF EACH. 1D AND 1A MODE REPLY12AD28 ARRKJ /D/A19PROVISION AND QUANTITY,ATTACHING ATTACHING PROVISION AND QUANTITY THE PROVISION/S/ INCLUDED IN THE DESIGN OF THE ITEM FOR ATTACHING TO A PANEL,CONTAINER,AND THE LIKE,AND THE NUMBER OF EACH. 1D AND 1A MODE REPLY13AB89 ARRLD 18TYPE,WINDOW WINDOW TYPE INDICATES THE TYPE OF WINDOW PROVIDED IN THE ITEM. SELECT REPLY CODE 10AL63 ARRMD /D/ 08LOCATION,REINFORCEMENT REINFORCEMENT LOCATION INDICATES THE LOCATION OF THE ITEM WHICH IS REINFORCED. SELECT REPLY CODE 10AJ91 ARRNJ /D/A19CHARACTERISTICS AND QUANTITY,POCKET POCKET CHARACTERISTICS AND QUANTITY AN INDICATION OF THE CHARACTERISTICS AND NUMBER OF THE POCKET/S/. 2D AND 1A MODE REPLY23AJ912AF87 ARRPG 19LEGEND,PREPRINTED PREPRINTED LEGEND THE DESCRIPTIVE,INSTRUCTIONAL LEGEND/S/,AND/OR SYMBOL/S/ PREPRINTED ON THE ITEM. FULL TEXT WRITE-IN 0 ARRQA 04SIZE,COMMERCIAL COMMERCIAL SIZE THE SIZE BY WHICH THE ITEM IS COMMERCIALLY RECOGNIZED. 1A MODE REPLY 0 ARRRJ 04WIDTH,BOTTOM BOTTOM WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ARRSJ 04WIDTH,GUSSET GUSSET WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ARRTJ 04WIDTH,OPENING,NECK NECK OPENING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 ARRWJ 04WIDTH,TOP TOP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE MEASURED LENGTH OF THE TOP TAKEN AS A UNIT OF MEASURE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ARRXG 10PERCENTAGE,COMPOSITION,CHEMICAL CHEMICAL COMPOSITION PERCENTAGE THE ELEMENT(S) USED IN THE FABRICATION OF THE ITEM,EXPRESSED IN PERCENT. FULL TEXT WRITE-IN 0 ARRYG /D/ 10PERCENTAGE,COMPOSITION,CHEMICAL,DEPOSITED WELD METAL DEPOSITED WELD METAL CHEMICAL COMPOSITION PERCENTAGE THE ELEMENT/S/ PRESENT IN THE METAL DEPOSITED BY THE WELDING PROCESS,EXPRESSED IN PERCENT. FULL TEXT WRITE-IN 0 ARRZG 04SIZE,CROSS-SECTIONAL CROSS-SECTIONAL SIZE A MEASUREMENT OF A CHORD PASSING THROUGH THE CENTER OF A FIGURE OR BODY. FULL TEXT WRITE-IN 0 ARSAD /D/ 07COATING,COPPER COPPER COATING AN INDICATION OF WHETHER OR NOT A COPPER COATING IS INCLUDED. SELECT REPLY CODE 10AA49 ARSBD 19PROCESS FOR WHICH DESIGNED,WELDING WELDING PROCESS FOR WHICH DESIGNED THE TYPE OF WELD FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL66 ARSCD 19POSITION FOR WHICH DESIGNED,WELD WELD POSITION FOR WHICH DESIGNED THE WELD POSITION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AF63 ARSDG 10CONTENT WITHIN EACH UNIT PACKAGE CONTENT WITHIN EACH UNIT PACKAGE THE AMOUNT OF THE ITEM CONTAINED WITHIN EACH UNIT PACKAGE. FULL TEXT WRITE-IN 0 ARSED 19SIZE,GRANULE GRANULE SIZE DESIGNATES THE SIZE OF THE GRANULES. SELECT REPLY CODE 10AF67 ARSFA 10CARAT RATING WITH WHICH USED,GOLD ALLOY GOLD ALLOY CARAT RATING WITH WHICH USED THE CARAT RATING OF THE GOLD ALLOY WITH WHICH THE ITEM IS USED. 1A MODE REPLY 0 ARSGD 18TYPE,CORE,WIRE WIRE CORE TYPE INDICATES THE TYPE OF CORE USED IN THE WIRE. SELECT REPLY CODE 10AG36 ARSHD /D/ 19PROCESS FOR WHICH DESIGNED,CUTTING CUTTING PROCESS FOR WHICH DESIGNED AN INDICATION OF THE CUTTING PROCESS FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL66 ARSJD /D/ 07FEATURE,SURFACE,CONCAVE CONCAVE SURFACE FEATURE AN INDICATION OF WHETHER OR NOT A CONCAVE SURFACE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARSKD /D/ 07INSULATOR INSULATOR AN INDICATION OF WHETHER OR NOT AN INSULATOR IS INCLUDED. SELECT REPLY CODE 10AA49 ARSLD 19INTENSITY,OPERATION,ARC ARC OPERATION INTENSITY AN INDICATION OF THE INTENSITY REQUIRED FOR ARC OPERATION. SELECT REPLY CODE 10AK07 ARSMD /D/ 07FEATURE,SPECTROSCOPIC SPECTROSCOPIC FEATURE AN INDICATION OF WHETHER OR NOT A SPECTROSCOPIC FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARSNB 10CONTENT IN PERCENT,ASH ASH CONTENT IN PERCENT THE AMOUNT OF ASH CONTAINED IN THE ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 ARSPD 13THREAD LOCATION,INLET INLET THREAD LOCATION INDICATES THE LOCATION OF THE THREAD ON THE INLET. SELECT REPLY CODE 10AJ91 ARSQJ 04DIAMETER,OUTSIDE,INLET INLET OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INLET,WITH TERMINATED POINTS ON THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARSRJ 04LENGTH,UNIT,SUBSTANCE SUBSTANCE UNIT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SUBSTANCE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 ARSSJ 04WIDTH,UNIT,SUBSTANCE SUBSTANCE UNIT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SUBSTANCE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 ARSTD /D/ 07FEATURE,GUMMED GUMMED FEATURE AN INDICATION OF WHETHER OR NOT A GUMMED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARSWD 18TYPE,PULP PULP TYPE INDICATES THE TYPE OF PULP PROVIDED. SELECT REPLY CODE 10AL60 ARSXA 12QUANTITY PER FOOT,CORRUGATION CORRUGATION QUANTITY PER FOOT THE NUMBER OF CORRUGATIONS PER FOOT. 1A MODE REPLY 0 ARSYD /D/ 07FEATURE,MOLDABLE MOLDABLE FEATURE AN INDICATION OF WHETHER OR NOT A MOLDABLE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARSZD /D/ 07FEATURE,ADHERING ADHERING FEATURE AN INDICATION OF WHETHER OR NOT AN ADHERING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARTAD /D/ 18TYPE,COATING COATING TYPE INDICATES THE TYPE OF COATING PROVIDED. SELECT REPLY CODE 10AL61 ARTBJ 10PERCENTAGE,STRETCH STRETCH PERCENTAGE THE AVERAGE NUMERIC PERCENTAGE OF STRETCH OF THE ITEM. 1D AND 1B MODE REPLY12AF06 ARTCD /D/ 07FEATURE,REPLACEABILITY,TIP TIP REPLACEABILITY FEATURE AN INDICATION OF WHETHER OR NOT A REPLACEABLE TIP FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARTDJ 10CIRCUMFERENCE,OVERALL OVERALL CIRCUMFERENCE THE DISTANCE AROUND THE OUTSIDE OF A CIRCULAR OBJECT. 2D AND 1B MODE REPLY21AA051AC20 ARTEJ 04DIAMETER,INSIDE,INLET INLET INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INLET,WITH TERMINATED POINTS ON THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARTFJ 04LENGTH,PIPE,EXHAUST,INLET INTEGRAL MANIFOLD INLET INTEGRAL MANIFOLD EXHAUST PIPE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN INLET INTEGRAL MANIFOLD EXHAUST PIPE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARTGA 12QUANTITY,CONNECTION,OUTLET OUTLET CONNECTION QUANTITY THE NUMBER OF OUTLET CONNECTIONS ON THE ITEM. 1A MODE REPLY 0 ARTHD 18TYPE,CONNECTION,OUTLET OUTLET CONNECTION TYPE A NARRATIVE DESCRIPTION OF THE TYPE OF OUTLET CONNECTION. SELECT REPLY CODE 10AB76 ARTJG 08LOCATION,OUTLET OUTLET LOCATION THE LOCATION OF THE OUTLET. FULL TEXT WRITE-IN 0 ARTKJ 04LENGTH,PROJECTION,OUTLET OUTLET PROJECTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE OUTLET PROJECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARTLD 14SHAPE,FLANGE,OUTLET OUTLET FLANGE SHAPE THE PHYSICAL CONFIGURATION OF THE OUTLET FLANGE. SELECT REPLY CODE 10AD07 ARTMJ A19PROVISION AND QUANTITY,MOUNTING,OUTLET FLANGE OUTLET FLANGE MOUNTING PROVISION AND QUANTITY INDICATES THE TYPE AND NUMBER OF OUTLET FLANGE MOUNTING PROVISIONS PROVIDED. 1D AND 1A MODE REPLY12AB89 ARTNJ 04DIAMETER,HOLE,OUTLET FLANGE MOUNTING OUTLET FLANGE MOUNTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE PASSING THROUGH THE CENTER OF AN OUTLET FLANGE MOUNTING HOLE,AND TERMINATING AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARTPJ 04LENGTH,STUD,MOUNTING,OUTLET FLANGE OUTLET FLANGE MOUNTING STUD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN OUTLET FLANGE MOUNTING STUD,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARTQA /D/ 13THREAD SIZE,PROVISION,OUTLET FLANGE MOUNTING OUTLET FLANGE MOUNTING PROVISION THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE OUTLET FLANGE MOUNTING PROVISION. 1A MODE REPLY 0 ARTRD 13THREAD SERIES DESIGNATOR,PROVISION,OUTLET FLANGE MOUNTING OUTLET FLANGE MOUNTING PROVISION THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF AN OUTLET FLANGE MOUNTING PROVISION. SELECT REPLY CODE 10AH06 ARTSD 13THREAD DIRECTION,PROVISION,OUTLET FLANGE MOUNTING OUTLET FLANGE MOUNTING PROVISION THREAD DIRECTION THE DIRECTION OF THE OUTLET FLANGE MOUNTING PROVISION THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ARTTG 04SPACING,PROVISION,OUTLET FLANGE MOUNTING OUTLET FLANGE MOUNTING PROVISION SPACING A MEASUREMENT OF THE SPACING OF THE OUTLET FLANGE MOUNTING PROVISION. FULL TEXT WRITE-IN 0 ARTWA 13THREAD SIZE,OUTLET OUTLET THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE OUTLET. 1A MODE REPLY 0 ARTXD 13THREAD SERIES DESIGNATOR,OUTLET OUTLET THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF AN OUTLET. SELECT REPLY CODE 10AH06 ARTYD 13THREAD DIRECTION,OUTLET OUTLET THREAD DIRECTION THE DIRECTION OF THE OUTLET THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ARTZD /D/ 13THREAD LOCATION,OUTLET OUTLET THREAD LOCATION INDICATES THE LOCATION OF THE THREAD ON THE OUTLET. SELECT REPLY CODE 10AJ91 ARWAJ 04DIAMETER,OUTSIDE,OUTLET OUTLET OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTLET,WITH TERMINATED POINTS ON THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARWBD 13THREAD DIRECTION,OUTLET,WATER WATER OUTLET THREAD DIRECTION THE DIRECTION OF THE WATER OUTLET THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ARWCJ 04LENGTH,PIPE,TAIL,OUTLET INTEGRAL OUTLET INTEGRAL TAIL PIPE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE OUTLET INTEGRAL TAIL PIPE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARWDJ /D/ 04LENGTH,PIPE,EXHAUST,OUTLET INTEGRAL MANIFOLD OUTLET INTEGRAL MANIFOLD EXHAUST PIPE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE OUTLET INTEGRAL MANIFOLD EXHAUST PIPE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARWED 18TYPE,CONNECTION,WATER INLET WATER INLET CONNECTION TYPE A NARRATIVE DESCRIPTION OF THE TYPE OF WATER INLET CONNECTION. SELECT REPLY CODE 10AB76 ARWFG 08LOCATION,INLET,WATER WATER INLET LOCATION THE LOCATION OF THE WATER INLET. FULL TEXT WRITE-IN 0 ARWGJ 04LENGTH,PROJECTION,WATER INLET WATER INLET PROJECTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE WATER INLET PROJECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARWHD 14SHAPE,FLANGE,WATER INLET WATER INLET FLANGE SHAPE THE PHYSICAL CONFIGURATION OF THE WATER INLET FLANGE. SELECT REPLY CODE 10AD07 ARWJG 04SPACING,HOLE,WATER INLET FLANGE BOLT WATER INLET FLANGE BOLT HOLE SPACING A MEASUREMENT OF THE SPACING OF THE WATER INLET FLANGE BOLT HOLES. FULL TEXT WRITE-IN 0 ARWKA 12QUANTITY,HOLE,BOLT,WATER INLET FLANGE WATER INLET FLANGE BOLT HOLE QUANTITY THE NUMBER OF WATER INLET FLANGE BOLT HOLES PROVIDED. 1A MODE REPLY 0 ARWLJ 04DIAMETER,HOLE,BOLT,WATER INLET FLANGE WATER INLET FLANGE BOLT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WATER INLET FLANGE BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARWMD /D/ 18TYPE,BACKING,PAPER PAPER BACKING TYPE THE TYPE OF PAPER BACKING PROVIDED. SELECT REPLY CODE 10AL60 ARWND 18TYPE,SOLVENT,ADHESIVE ACTIVATING ADHESIVE ACTIVATING SOLVENT TYPE THE TYPE OF ADHESIVE ACTIVATING SOLVENT PROVIDED. SELECT REPLY CODE 10AB75 ARWPD /D/ 08LOCATION,ADHESIVE ADHESIVE LOCATION THE LOCATION OF THE ADHESIVE ON THE ITEM. SELECT REPLY CODE 10AJ91 ARWQD /D/ 07FEATURE,LINER LINER FEATURE AN INDICATION OF WHETHER OR NOT A LINER FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ARWRD /D/ 08LOCATION,ADHESIVE,WOUND TAPE WOUND TAPE ADHESIVE LOCATION THE LOCATION OF THE WOUND TAPE ADHESIVE. SELECT REPLY CODE 10AJ91 ARWSD /D/ 07DISPENSER,CUTTING CUTTING DISPENSER AN INDICATION OF WHETHER OR NOT A CUTTING DISPENSER IS INCLUDED. SELECT REPLY CODE 10AA49 ARWTA /D/ 13THREAD SIZE,HOLE,BOLT,WATER INLET FLANGE WATER INLET FLANGE BOLT HOLE THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE WATER INLET FLANGE BOLT HOLE. 1A MODE REPLY 0 ARWWD 13THREAD SERIES DESIGNATOR,HOLE,BOLT,WATER INLET FLANGE WATER INLET FLANGE BOLT HOLE THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASURMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A WATER INLET FLANGE BOLT HOLE. SELECT REPLY CODE 10AH06 ARWXD /D/ 13THREAD DIRECTION,HOLE,BOLT,WATER INLET FLANGE WATER INLET FLANGE BOLT HOLE THREAD DIRECTION THE DIRECTION OF THE WATER INLET FLANGE BOLT HOLE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ARWYA 13THREAD SIZE,INLET,WATER WATER INLET THREAD SIZE DESIGNATES THE THREAD DIAMETER AND QUANTITY OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1A MODE REPLY 0 ARWZD 13THREAD SERIES DESIGNATOR,INLET,WATER WATER INLET THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A WATER INLET. SELECT REPLY CODE 10AH06 ARXAD 13THREAD DIRECTION,INLET,WATER WATER INLET THREAD DIRECTION THE DIRECTION OF THE WATER INLET THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ARXBD 13THREAD LOCATION,INLET,WATER WATER INLET THREAD LOCATION INDICATES THE LOCATION/S/ OF THE WATER INLET ON WHICH THREAD IS LOCATED. SELECT REPLY CODE 10AJ91 ARXCJ 04DIAMETER,OUTSIDE,WATER INLET WATER INLET OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WATER INLET,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARXDJ 04DIAMETER,INSIDE,WATER INLET WATER INLET INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WATER INLET,WITH TERMINATED POINTS ON THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARXED 18TYPE,CONNECTION,WATER OUTLET WATER OUTLET CONNECTION TYPE A NARRATIVE DESCRIPTION OF THE TYPE OF WATER OUTLET CONNECTION. SELECT REPLY CODE 10AB76 ARXFA 12QUANTITY,OUTLET,WATER WATER OUTLET QUANTITY THE NUMBER OF WATER OUTLETS FURNISHED WITH THE ITEM. 1A MODE REPLY 0 ARXGG 08LOCATION,OUTLET,WATER WATER OUTLET LOCATION THE LOCATION OF THE WATER OUTLET. FULL TEXT WRITE-IN 0 ARXHJ 04LENGTH,PROJECTION,WATER OUTLET WATER OUTLET PROJECTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE WATER OUTLET PROJECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARXJD 14SHAPE,FLANGE,WATER OUTLET WATER OUTLET FLANGE SHAPE THE PHYSICAL CONFIGURATION OF THE WATER OUTLET FLANGE. SELECT REPLY CODE 10AD07 ARXKJ 04DIAMETER,CIRCLE,BOLT,WATER OUTLET FLANGE WATER OUTLET FLANGE BOLT CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE PASSING THROUGH THE CENTER OF THE WATER OUTLET FLANGE BOLT CIRCLE,WITH TERMINATED POINTS AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARXLA 12QUANTITY,HOLE,BOLT,WATER OUTLET FLANGE WATER OUTLET FLANGE BOLT HOLE QUANTITY THE NUMBER OF BOLT HOLES INCLUDED ON THE WATER OUTLET FLANGE. 1A MODE REPLY 0 ARXMJ 04DIAMETER,HOLE,BOLT,WATER OUTLET FLANGE WATER OUTLET FLANGE BOLT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE PASSING THROUGH THE CENTER OF A WATER OUTLET FLANGE BOLT HOLE,AND TERMINATING AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARXNA /D/ 13THREAD SIZE,HOLE,BOLT,WATER OUTLET FLANGE WATER OUTLET FLANGE BOLT HOLE THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE WATER OUTLET FLANGE BOLT HOLE. 1A MODE REPLY 0 ARXPD /D/ 13THREAD SERIES DESIGNATOR,HOLE,BOLT,WATER OUTLET FLANGE WATER OUTLET FLANGE BOLT HOLE THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A WATER OUTLET FLANGE BOLT HOLE. SELECT REPLY CODE 10AH06 ARXQD /D/ 13THREAD DIRECTION,HOLE,BOLT,WATER OUTLET FLANGE WATER OUTLET FLANGE BOLT HOLE THREAD DIRECTION THE DIRECTION OF THE WATER OUTLET FLANGE BOLT HOLE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ARXRA 13THREAD SIZE,OUTLET,WATER WATER OUTLET THREAD SIZE DESIGNATES THE THREAD DIAMETER AND QUANTITY OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1A MODE REPLY 0 ARXSD 13THREAD SERIES DESIGNATOR,OUTLET,WATER WATER OUTLET THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE APPLIED TO A SERIES OF A SPECIFIC DIAMETERS OF A WATER OUTLET. SELECT REPLY CODE 10AH06 ARXTD 13THREAD LOCATION,OUTLET,WATER WATER OUTLET THREAD LOCATION INDICATES THE LOCATION/S/ OF THE WATER OUTLET ON WHICH THE THREAD IS LOCATED. SELECT REPLY CODE 10AJ91 ARXWJ 04DIAMETER,OUTSIDE,WATER OUTLET WATER OUTLET OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WATER OUTLET,WITH TERMINATED POINTS ON THE OUTSIDE CIRCUMFERNCE. 2D AND 1B MODE REPLY21AA051AC20 ARXXJ 04DIAMETER,INSIDE,WATER OUTLET WATER OUTLET INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WATER OUTLET,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARXYJ A18TYPE AND QUANTITY,OUTLET,NONCONNECTION NONCONNECTION OUTLET TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF NONCONNECTION OUTLETS USED ON THE ITEM. 1D AND 1A MODE REPLY12AL64 ARXZG 08LOCATION,OUTLET,NONCONNECTION NONCONNECTION OUTLET LOCATION INDICATES THE LOCATION/S/ OF THE NONCONNECTION OUTLET ON THE ITEM. FULL TEXT WRITE-IN 0 ARYAG 04SIZE,OUTLET,NONCONNECTION NONCONNECTION OUTLET SIZE DESIGNATES THE SIZE OF THE NONCONNECTION OUTLET INCLUDED ON THE ITEM. FULL TEXT WRITE-IN 0 ARYBA 12QUANTITY,HOLE,HAND HAND HOLE QUANTITY THE NUMBER OF HAND HOLES PROVIDED ON THE ITEM. 1A MODE REPLY 0 ARYCD 18TYPE,CLEANER,AIR AIR CLEANER TYPE AN INDICATION OF THE TYPE OF AIR CLEANER USED WITH THE ITEM. SELECT REPLY CODE 10AL65 ARYDD 07REPLACEABILITY,ELEMENT ELEMENT REPLACEABILITY AN INDICATION OF WHETHER OR NOT THE ELEMENT IS REPLACEABLE. SELECT REPLY CODE 10AG84 ARYED /D/ 07VALVE,RELIEF,PRESSURE PRESSURE RELIEF VALVE AN INDICATION OF WHETHER OR NOT A PRESSURE RELIEF VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 ARYFD /D/ 07VALVE,BACKFIRE BACKFIRE VALVE AN INDICATION OF WHETHER OR NOT A BACKFIRE VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 ARYGD 18TYPE,INLET INLET TYPE THE TYPE OF INLET INCLUDED ON THE ITEM. SELECT REPLY CODE 10AH98 ARYHG 08LOCATION,SLEEVE SLEEVE LOCATION THE LOCATION OF THE SLEEVE. FULL TEXT WRITE-IN 0 ARYJA /D/ 12QUANTITY PER POUND,SQUARE INCH SQUARE INCH QUANTITY PER POUND THE NUMBER OF SQUARE INCHES CONTAINED IN EACH POUND WEIGHT OF THE ITEM. 1A MODE REPLY 0 ARYKD /D/ 08LOCATION,CREPED CREPED LOCATION INDICATES THE LOCATION OF THE ITEM WHICH IS CREPED. SELECT REPLY CODE 10AJ91 ARYLJ 04LENGTH,SETUP SETUP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF ANY SETUP ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ARYMJ 04WIDTH,SETUP SETUP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A SETUP ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ARYNJ 04DEPTH,SETUP SETUP DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON A SETUP ITEM IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 ARYPJ 04DISTANCE BETWEEN PRODS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN PRODS THE CENTER TO CENTER DISTANCE BETWEEN PRODS ON AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 ARYQA 12QUANTITY,PROD PROD QUANTITY THE NUMBER OF PRODS PROVIDED. 1A MODE REPLY 0 ARYRB /D/ 10WEIGHT IN POUNDS,COIL COIL WEIGHT IN POUNDS THE WEIGHT OF THE COIL,EXPRESSED IN POUNDS. 1B MODE REPLY 0 ARYSG 19RECORDED,INFORMATION INFORMATION RECORDED INDICATES THE TYPE OF INFORMATION THE ITEM WILL RECORD. FULL TEXT WRITE-IN 0 ARYTA 12QUANTITY,CONNECTION,SLEEVE SLEEVE CONNECTION QUANTITY THE NUMBER OF SLEEVE CONNECTION(S)FURNISHED WITH THE ITEM. 1A MODE REPLY 0 ARYWJ 04DIAMETER,OUTSIDE,SLEEVE SLEEVE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SLEEVE,WITH TERMINATED POINTS ON THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARYXJ 04DIAMETER,INSIDE,SLEEVE SLEEVE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SLEEVE,WITH TERMINATED POINTS ON THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARYYD 14SHAPE,FLANGE,SLEEVE SLEEVE FLANGE SHAPE THE PHYSICAL CONFIGURATION OF THE SLEEVE FLANGE. SELECT REPLY CODE 10AD07 ARYZJ A19PROVISION AND QUANTITY,MOUNTING,SLEEVE FLANGE SLEEVE FLANGE MOUNTING PROVISION AND QUANTITY INDICATES THE TYPE AND NUMBER OF SLEEVE FLANGE MOUNTING PROVISION(S) PROVIDED. 1D AND 1A MODE REPLY12AB89 ARZAJ 04DIAMETER,HOLE,SLEEVE FLANGE MOUNTING SLEEVE FLANGE MOUNTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SLEEVE FLANGE MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARZBA /D/ 13THREAD SIZE,PROVISION,SLEEVE FLANGE MOUNTING SLEEVE FLANGE MOUNTING PROVISION THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER INCH ON THE SLEEVE FLANGE MOUNTING PROVISION. 1A MODE REPLY 0 ARZCD 13THREAD SERIES DESIGNATOR,PROVISION,SLEEVE FLANGE MOUNTING SLEEVE FLANGE MOUNTING PROVISION THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A SLEEVE FLANGE MOUNTING PROVISION. SELECT REPLY CODE 10AH06 ARZDD 13THREAD DIRECTION,PROVISION,SLEEVE FLANGE MOUNTING SLEEVE FLANGE MOUNTING PROVISION THREAD DIRECTION THE DIRECTION OF THE SLEEVE FLANGE MOUNTING PROVISION THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ARZEG 04SPACING,PROVISION,SLEEVE FLANGE MOUNTING SLEEVE FLANGE MOUNTING PROVISION SPACING A MEASUREMENT OF THE SPACING OF THE SLEEVE FLANGE MOUNTING PROVISION. FULL TEXT WRITE-IN 0 ARZFD 18TYPE,ELEMENT ELEMENT TYPE THE TYPE OF ELEMENT(S) USED WITH THE ITEM. SELECT REPLY CODE 10AL67 ARZGD 18TYPE,OUTLET OUTLET TYPE THE TYPE OF OUTLET INCLUDED ON THE ITEM. SELECT REPLY CODE 10AB76 ARZHJ A19PROVISION AND QUANTITY,MOUNTING,FLANGE FLANGE MOUNTING PROVISION AND QUANTITY THE TYPE AND NUMBER OF FLANGE MOUNTING PROVISIONS INCLUDED. 1D AND 1A MODE REPLY12AB89 ARZJJ 04DIAMETER,HOLE,FLANGE BOLT FLANGE BOLT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FLANGE BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARZKA /D/ 13THREAD SIZE,PROVISION,FLANGE MOUNTING FLANGE MOUNTING PROVISION THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER INCH ON THE FLANGE MOUNTING PROVISION. 1A MODE REPLY 0 ARZLD 13THREAD SERIES DESIGNATOR,PROVISION, FLANGE MOUNTING FLANGE MOUNTING PROVISION THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A FLANGE MOUNTING PROVISION. SELECT REPLY CODE 10AH06 ARZMD 13THREAD DIRECTION,PROVISION,FLANGE MOUNTING FLANGE MOUNTING PROVISION THREAD DIRECTION THE DIRECTION OF THE FLANGE MOUNTING PROVISION THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ARZNG 04SPACING,PROVISION,FLANGE MOUNTING FLANGE MOUNTING PROVISION SPACING A MEASUREMENT OF THE SPACING OF THE FLANGE MOUNTING PROVISION. FULL TEXT WRITE-IN 0 ARZPD 18TYPE,SLEEVE,OUTLET OUTLET SLEEVE TYPE THE TYPE OF OUTLET SLEEVE USED ON THE ITEM. SELECT REPLY CODE 10AH46 ARZQJ 04DIAMETER,INSIDE,MOUNTING MOUNTING INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING,WITH TERMINATED POINTS ON THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ARZRD /D/ 07CLAMP,INTEGRAL INTEGRAL CLAMP AN INDICATION AS TO WHETHER OR NOT AN INTEGRAL CLAMP IS INCLUDED. SELECT REPLY CODE 10AA49 ARZSA /D/ 13THREAD SIZE,PROVISION,MOUNTING MOUNTING PROVISION THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER INCH ON THE MOUNTING PROVISION. 1A MODE REPLY 0 ARZTD 13THREAD SERIES DESIGNATOR,PROVISION,MOUNTING MOUNTING PROVISION THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A MOUNTING PROVISION. SELECT REPLY CODE 10AH06 ARZWD /D/ 07ADAPTER,INLET,REMOTE LOCATION REMOTE LOCATION INLET ADAPTER AN INDICATION AS TO WHETHER OT NOT AN INLET ADAPTER FOR REMOTE LOCATION IS INCLUDED. SELECT REPLY CODE 10AA49 ARZXD /D/ 09MATERIAL,WARP WARP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WARP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ARZYD /D/ 07STRAND,ELASTIC ELASTIC STRAND AN INDICATION OF WHETHER OR NOT ELASTIC STRAND(S) ARE INCLUDED. SELECT REPLY CODE 10AA49 ARZZD /D/ 11METHOD,WEAVE WEAVE METHOD THE MEANS BY WHICH THE WEAVE IS INTERWOVEN. SELECT REPLY CODE 10AG70 ASAAJ 04DIAMETER,OUTSIDE,ADAPTER ADAPTER OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ADAPTER,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ASABJ 04DIAMETER,INSIDE,ADAPTER ADAPTER INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ADAPTER,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ASACA 13THREAD SIZE,ADAPTER,INLET INLET ADAPTER THREAD SIZE DESIGNATES THE INLET ADAPTER THREAD DIAMETER AND NUMBER OF THREADS PER INCH. 1A MODE REPLY 0 ASADD 13THREAD SERIES DESIGNATOR,ADAPTER,INLET INLET ADAPTER THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF AN INLET ADAPTER. SELECT REPLY CODE 10AH06 ASAED 13THREAD DIRECTION,ADAPTER,INLET INLET ADAPTER THREAD DIRECTION THE DIRECTION OF THE INLET ADAPTER THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ASAFA 12QUANTITY,PRECLEANER PRECLEANER QUANTITY THE NUMBER OF PRECLEANERS INCLUDED ON THE ITEM. 1A MODE REPLY 0 ASAGG 08LOCATION,PRECLEANER PRECLEANER LOCATION INDICATES THE LOCATION OF THE PRECLEANER/S/ ON THE ITEM. FULL TEXT WRITE-IN 0 ASAHD /D/ 07TUBE,EXTENDED EXTENDED TUBE AN INDICATION OF WHETHER OR NOT AN EXTENDED TUBE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 ASAJJ 10PRESSURE,INLET,AIR SUPPLY AIR SUPPLY INLET PRESSURE THE AIR SUPPLY INLET PRESSURE PROVIDED. 1D AND 1B MODE REPLY12AB16 ASAKJ 10TEMP RATING,INLET,AIR SUPPLY AIR SUPPLY INLET TEMP RATING THE RATED TEMPERATURE OF THE INLET AIR SUPPLY. 1D AND 1B MODE REPLY11AB36 ASALJ 10FLOW RATE,SUPPLY,AIR AIR SUPPLY FLOW RATE THE FLOW RATE OF THE AIR SUPPLY. 1D AND 1B MODE REPLY12AL69 ASAMJ 10TORQUE RATING,OUTPUT OUTPUT TORQUE RATING THE ABILITY OF AN ITEM TO WITHSTAND A SPECIFIED TORQUE OUTPUT WITHOUT FRACTURE. 2D AND 1B MODE REPLY21AA561AC20 ASAND 05DIRECTION,ROTATION,DRIVE DRIVE ROTATION DIRECTION THE DIRECTION OF ROTATION OF A ROTATING DRIVE. SELECT REPLY CODE 10AC84 ASAPA 10PITCH,SPLINE SPLINE PITCH A MEASUREMENT OF THE SPLINE PITCH OF THE ITEM. 1A MODE REPLY 0 ASAQJ 04DIAMETER,CIRCLE,PITCH PITCH CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PITCH CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ASARD 18TYPE,CONNECTION,AIR INLET AIR INLET CONNECTION TYPE INDICATES THE TYPE OF AIR INLET CONNECTION ON THE ITEM. SELECT REPLY CODE 10AB76 ASASA 12QUANTITY,HOLE,INLET FLANGE MOUNTING INLET FLANGE MOUNTING HOLE QUANTITY THE NUMBER OF INLET FLANGE MOUNTING HOLES PROVIDED. 1A MODE REPLY 0 ASATA /D/ 13THREAD SIZE,HOLE,INLET MOUNTING INLET MOUNTING HOLE THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE INLET MOUNTING HOLE. 1A MODE REPLY 0 ASAWG /D/ 04SPACING,HOLE,INLET FLANGE MOUNTING INLET FLANGE MOUNTING HOLE SPACING THE SPACING OF THE INLET FLANGE MOUNTING HOLES. FULL TEXT WRITE-IN 0 ASAXD /D/ 07FEATURE,MOUNTING,QUICK DETACHABLE QUICK DETACHABLE MOUNTING FEATURE AN INDICATION OF WHETHER OR NOT A QUICK DETACHABLE MOUNTING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ASAYD /D/ 09MATERIAL,PULP PULP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PULP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 ASAZJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CONNECTION,DISCHARGE DISCHARGE CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE DISCHARGE CONNECTION. 1D AND 1A MODE REPLY12AH06 ASBAB 10CONTENT IN PERCENT,FIBER,MINIMUM COTTON MINIMUM COTTON FIBER CONTENT IN PERCENT THE MINIMUM NUMBER OF COTTON FIBERS,EXPRESSED IN PERCENT. 1B MODE REPLY 0 ASBBD 19TREATMENT,CHEMICAL CHEMICAL TREATMENT AN INDICATION OF THE CHEMICAL TREATMENT PROVIDED. SELECT REPLY CODE 10AJ08 ASBCJ 10WEIGHT,BASIS,NOMINAL NOMINAL BASIS WEIGHT THE NOMINAL WEIGHT BASED ON A SPECIFIED AMOUNT,SIZE,OR THE LIKE. 1D AND 1B MODE REPLY13AL62 ASBDJ 04DIAMETER,OUTSIDE,ROLL ROLL OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ROLL,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ASBEA 03DESIGNATOR,TYPE,MOUNTING MOUNTING TYPE DESIGNATOR THE DESIGNATOR IDENTIFYING THE MOUNTING USED ON THE ITEM. 1A MODE REPLY 0 ASBGD /D/ 07FEATURE,CORE,METAL METAL CORE FEATURE AN INDICATION OF WHETHER OR NOT A METAL CORE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ASBHD 14SHAPE,FACE FACE SHAPE THE PHYSICAL CONFIGURATION OF THE FACE. SELECT REPLY CODE 10AD07 ASBJJ 04WIDTH,ACCOMMODATION,ROPE ROPE ACCOMMODATION WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ACCOMMODATION OF THAT PORTION OF THE ITEM AROUND WHICH THE ROPE IS WOUND,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ASBKJ 04DIAMETER,ACCOMMODATION,ROPE ROPE ACCOMMODATION DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION OF THAT PORTION OF THE ITEM AROUND WHICH THE ROPE IS WOUND,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ASBLD /D/ 07HUB HUB AN INDICATION OF WHETHER OR NOT A HUB IS INCLUDED. PLEASE USE MRC ABFF FOR NIINS WERE ANSWERED WITH "INCLUDED" IN PLACE OF THIS CANCELLED MRC. SELECT REPLY CODE 10AA49 ASBMJ 04DIAMETER,HUB HUB DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HUB,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ASBNJ /D/ 04LENGTH AND LOCATION,PROJECTION,HUB HUB PROJECTION LENGTH AND LOCATION A MEASUREMENT OF THE LONGEST DIMENSION OF THE HUB PROJECTION,IN DISTINCTION FROM WIDTH,AND ITS LOCATION. 3D AND 1B MODE REPLY31AA051AC203AJ91 ASBPD 18TYPE,BORE BORE TYPE INDICATES THE TYPE OF BORE USED ON THE ITEM. SELECT REPLY CODE 10AL72 ASBQJ 04TAPER,BORE BORE TAPER THE DIMINISHING MEASUREMENT OF THE DIAMETER ALONG THE MAJOR AXIS OF THE BORE. 2D AND 1B MODE REPLY22AG201AC20 ASBRH /D/ 09MATERIAL AND TYPE MATERIAL AND TYPE THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH AN ITEM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT,AND THE TYPE. 2D MODE REPLY 26AD091AD93 ASBSD 19CHARACTERISTIC,POLARITY POLARITY CHARACTERISTIC AN INDICATION OF THE POLARITY CHARACTERISTIC(S) OF THE ITEM. SELECT REPLY CODE 10AD21 ASBTD 18TYPE,COATING,FLUX FLUX COATING TYPE INDICATES THE TYPE OF FLUX COATING APPLIED ON THE SURFACE OF THE ITEM. SELECT REPLY CODE 10AL68 ASBWD /D/ 07FEATURE,USE,SIMULTANEOUS,MULTIPLE ELECTRODE MULTIPLE ELECTRODE SIMULTANEOUS USE FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE IS INCLUDED TO USE MULTIPLE ELECTRODES SIMULTANEOUSLY. SELECT REPLY CODE 10AA49 ASBXD 18TYPE FOR WHICH DESIGNED,ELECTRODE ELECTRODE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF ELECTRODE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AG81 ASBYJ 04DIAMETER FOR WHICH DESIGNED,ELECTRODE ELECTRODE DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ELECTRODE FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ASBZD /D/ 07JAW,REPLACEABLE REPLACEABLE JAW AN INDICATION OF WHETHER OR NOT A REPLACEABLE JAW/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 ASCAD 08LOCATION,VALVE,CONTROL CONTROL VALVE LOCATION INDICATES THE LOCATION OF THE CONTROL VALVE. SELECT REPLY CODE 10AJ91 ASCBD 19DEGREE,INSULATION INSULATION DEGREE THE EXTENT OF THE INSULATION USED ON THE ITEM. SELECT REPLY CODE 10AL70 ASCCA 19NUMBER,IDENTIFYING,CONNECTOR CONNECTOR IDENTIFYING NUMBER A NUMBER ASSIGNED TO THE CONNECTOR FOR PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 ASCDD /D/ 07ACCOMMODATION,HOSE,OXYGEN OXYGEN HOSE ACCOMMODATION AN INDICATION OF WHETHER OR NOT AN OXYGEN HOSE ACCOMMODATION IS INCLUDED. SELECT REPLY CODE 10AA49 ASCED /D/ 07JAW,SPARE SPARE JAW AN INDICATION OF WHETHER OR NOT A SPARE JAW(S) IS INCLUDED. SELECT REPLY CODE 10AA49 ASCFA /D/ 12QUANTITY,JAW,SPARE SPARE JAW QUANTITY THE NUMBER OF SPARE JAWS SUPPLIED. 1A MODE REPLY 0 ASCGD /D/ 07FEATURE,END,DOUBLE DOUBLE END FEATURE AN INDICATION OF WHETHER OR NOT A DOUBLE END FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ASCHD 14SHAPE,TIP TIP SHAPE THE PHYSICAL CONFIGURATION OF THE TIP. SELECT REPLY CODE 10AD07 ASCJB /D/ 10RESPONSE PER SECOND,FLUCTUATION FLUCTUATION RESPONSE PER SECOND THE NUMBER OF CHANGES PER SECOND THE ITEM IS CAPABLE OF FOLLOWING. 1B MODE REPLY 0 ASCKJ 10TIME,RESPONSE RESPONSE TIME THE TIME REQUIRED FOR AN ITEM TO RESPOND TO A SPECIFIC CONDITION. 2D AND 1B MODE REPLY22AH681AC20 ASCLD /D/ 03DESIGNATION,CURVE,STANDARD,SPECTRAL RESPONSE SPECTRAL RESPONSE STANDARD CURVE DESIGNATION A DESIGNATION USED TO IDENTIFY A SPECTRAL RESPONSE STANDARD CURVE. SELECT REPLY CODE 10AA27 ASCMJ /D/ 10RESPONSE IN ANGSTROM UNITS AT FIFTY PERCENT OF MAXIMUM LEVEL,SPECTRAL SPECTRAL RESPONSE IN ANGSTROM UNITS AT FIFTY PERCENT OF MAXIMUM LEVEL THE VALUE(S) OF VISIBLE LIGHT UNIT(S) TO WHICH THE UNIT WILL RESPOND AT FIFTY PERCENT MAXIMUM RESPONSE LEVEL,EXPRESSED IN ANGSTROM UNITS. 1D AND 1B MODE REPLY11AC20 ASCNG /D/ 10SENSITIVITY RATING,OUTPUT OUTPUT SENSITIVITY RATING THE DETECTABLE OUTPUT OF AN ITEM WHEN EXCITED BY A SPECIFIED VALUE OF CURRENT,VOLTAGE,LIGHT,AND THE LIKE. FULL TEXT WRITE-IN 0 ASCPD /D/ 19CONSTRUCTION,EFFECT,FIELD FIELD EFFECT CONSTRUCTION THE STRUCTURAL CHARACTERISTIC OF THE FIELD EFFECT. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AL59 ASCQD 19CONFIGURATION,JUNCTION,INTERNAL INTERNAL JUNCTION CONFIGURATION THE SYMBOL INDICATING THE INTERNAL JUNCTION PATTERN OF THE ITEM. SELECT REPLY CODE 10AH14 ASCRD /D/ 19COMPONENT,CONNECTED,INTERNALLY INTERNALLY CONNECTED COMPONENT AN INDICATION OF THE INTERNALLY CONNECTED COMPONENT. SELECT REPLY CODE 10AE15 ASCSA /D/ 16STYLE DESIGNATOR,CONNECTION,CIRCUIT CIRCUIT CONNECTION STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CIRCUIT CONNECTION. 1A MODE REPLY 0 ASCTJ 10VOLTAGE RATING,MAXIMUM,RMS INPUT RMS INPUT MAXIMUM VOLTAGE RATING THE HIGHEST VALUE OF ROOT MEAN SQUARE POTENTIAL THAT CAN BE INPUT TO THE ITEM. 1D AND 1B MODE REPLY11AB63 ASCWJ 10CURRENT RATING,MAXIMUM,DC OUTPUT DC OUTPUT MAXIMUM CURRENT RATING THE MAXIMUM AMOUNT OF DIRECT CURRENT THE ITEM IS DESIGNED TO OUTPUT. 1D AND 1B MODE REPLY11AC30 ASCXD 18TYPE,LOAD LOAD TYPE INDICATES THE TYPE OF LOAD FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK53 ASCYJ /D/ 10VOLTAGE RATING,MAXIMUM,DC OUTPUT DC OUTPUT MAXIMUM VOLTAGE RATING THE MAXIMUM VALUE OF DIRECT CURRENT OUTPUT FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AB632AL71 ASCZA 12QUANTITY,STACK STACK QUANTITY THE NUMBER OF STACKS IN THE ITEM. 1A MODE REPLY 0 ASDAA /D/ 16STYLE DESIGNATOR,CONNECTION,INDIVIDUAL STACK CIRCUIT INDIVIDUAL STACK CIRCUIT CONNECTION STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE INDIVIDUAL STACK CIRCUIT CONNECTION. 1A MODE REPLY 0 ASDBJ 04WIDTH ACROSS FLATS WIDTH ACROSS FLATS THE SHORTEST STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 ASDCD 07REMOVABILITY,TIP TIP REMOVABILITY AN INDICATION OF WHETHER OR NOT THE TIP IS REMOVABLE. SELECT REPLY CODE 10AC29 ASDDD 19RELATIONSHIP,FUNCTION,COMPONENT COMPONENT FUNCTION RELATIONSHIP AN INDICATION OF THE FUNCTIONAL RELATIONSHIP OF THE COMPONENTS. SELECT REPLY CODE 10AH61 ASDED /D/ 07CONTROL,HEAT,DUAL DUAL HEAT CONTROL AN INDICATION OF WHETHER OR NOT A DUAL HEAT CONTROL IS INCLUDED. USE MRC CBBL WITH REPLY OF DUJ. SELECT REPLY CODE 10AA49 ASDFD /D/ 07SPOTLIGHT SPOTLIGHT AN INDICATION OF WHETHER OR NOT A SPOTLIGHT IS INCLUDED. USE MRC CBBL WITH REPLY CODE OF ACJ. SELECT REPLY CODE 10AA49 ASDGD /D/ 07CONTROL,THERMOSTATIC THERMOSTATIC CONTROL AN INDICATION OF WHETHER OR NOT A THERMOSTATIC CONTROL IS INCLUDED. USE MRC CBBL WITH REPLY CODE DYD. SELECT REPLY CODE 10AA49 ASDHD 11METHOD,MOUNTING,TIP TIP MOUNTING METHOD THE MEANS OF ATTACHING THE TIP. SELECT REPLY CODE 10AB89 ASDJG 04SIZE,TIP TIP SIZE A STANDARD OF MEASUREMENT,EXPRESSED AS A DIMENSION OR NUMERIC VALUE,FOR DESIGNATING THE SIZE OF THE TIP. FULL TEXT WRITE-IN 0 ASDKJ 10WATTAGE RATING IN WATTS WATTAGE RATING IN WATTS THE RATED POWER THAT AN ITEM CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS. 1D AND 1B MODE REPLY11AC20 ASDLD /D/ 07PROVISION,CARTRIDGE,HEATING HEATING CARTRIDGE PROVISION AN INDICATION OF WHETHER OR NOT A PROVISION FOR A HEATING CARTRIDGE IS INCLUDED. SELECT REPLY CODE 10AA49 ASDMJ /D/A08LOCATION AND QUANTITY,NOTCH,ROPE STARTER RETAINING ROPE STARTER RETAINING NOTCH LOCATION AND QUANTITY INDICATES THE LOCATION AND NUMBER OF ROPE STARTER RETAINING NOTCHES INCLUDED ON THE ITEM. 1D AND 1A MODE REPLY13AJ91 ASDNG 19PROVISION AND LOCATION,SECURING,MISCELLANEOUS MISCELLANEOUS SECURING PROVISION AND LOCATION THE MISCELLANEOUS SECURING PROVISION AND LOCATION ON THE ITEM. FULL TEXT WRITE-IN 0 ASDPJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,SETSCREW SETSCREW THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE SETSCREW. 1D AND 1A MODE REPLY12AH06 ASDQJ /D/ 04TAPER,KEYWAY KEYWAY TAPER THE DIMINISHING MEASUREMENT OF THE KEYWAY. 2D AND 1B MODE REPLY22AG201AC20 ASDRD 19TRANSLUCENCY RATING TRANSLUCENCY RATING AN INDICATION OF THE TRANSLUCENCY RATING OF THE ITEM. SELECT REPLY CODE 10AE25 ASDSD /D/ 07TERMINAL,GROUNDED GROUNDED TERMINAL AN INDICATION OF WHETHER OR NOT GROUNDED TERMINAL(S) ARE INCLUDED. SELECT REPLY CODE 10AA49 ASDTA 12QUANTITY,RATING,COPY COPY RATING QUANTITY THE NUMBER OF COPIES THE ITEM IS RATED TO PRODUCE. 1A MODE REPLY 0 ASDWD 18TYPE,PAPER PAPER TYPE INDICATES THE TYPE OF PAPER. SELECT REPLY CODE 10AL73 ASDXD 19PROCESS,REPRODUCTION REPRODUCTION PROCESS AN INDICATION OF THE REPRODUCTION PROCESS. SELECT REPLY CODE 10AB75 ASDYA 12QUANTITY,TUBE,INDIVIDUAL INDIVIDUAL TUBE QUANTITY THE NUMBER OF INDIVIDUAL TUBES INCLUDED WITH THE ITEM. 1A MODE REPLY 0 ASDZD 19CHARACTERISTIC,MATCHED MATCHED CHARACTERISTIC THE EQUAL OR SIMILAR QUALITIES OF THE ITEM/S/ PROVIDED. SELECT REPLY CODE 10AL74 ASEAA 12QUANTITY,MAGNET MAGNET QUANTITY THE NUMBER OF MAGNETS PROVIDED. 1A MODE REPLY 0 ASEBD /D/ 09MATERIAL,PROTECTIVE,VIEWING END VIEWING END PROTECTIVE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PROTECTIVE MATERIAL ON THE VIEWING END IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ASECJ 04LENGTH,INSIDE,ATTACHMENT END ATTACHMENT END INSIDE LENGTH A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF THE ATTACHMENT END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ASEDJ 04DIAMETER,INSIDE,ATTACHMENT END ATTACHMENT END INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ATTACHMENT END,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ASEEJ 04WIDTH,INSIDE,ATTACHMENT END ATTACHMENT END INSIDE WIDTH AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ATTACHMENT END,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ASEFJ 04LENGTH,INSIDE,VIEWING END VIEWING END INSIDE LENGTH A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF THE VIEWING END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ASEGJ 04DIAMETER,INSIDE,VIEWING END VIEWING END INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE VIEWING END,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ASEHJ 04WIDTH,INSIDE,VIEWING END VIEWING END INSIDE WIDTH AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE VIEWING END,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ASEJG 04SPACING DIMENSION,HOLE HOLE SPACING DIMENSION THE NARRATIVE EXPRESSION USED FOR INDICATING THE HOLE SPACING. FULL TEXT WRITE-IN 0 ASEKJ /D/ 19CHARACTERISTIC,HOLE HOLE CHARACTERISTIC THE CHARACTERISTIC OF A HOLE. 2D AND 1B MODE REPLY21AA052AL72 ASELD 11METHOD,MOUNTING,SECOND END SECOND END MOUNTING METHOD THE MEANS OF ATTACHING THE SECOND END OF THE ITEM. SELECT REPLY CODE 10AB89 ASEMD 11METHOD,MOUNTING,FIRST END FIRST END MOUNTING METHOD THE MEANS OF ATTACHING THE FIRST END OF THE ITEM. SELECT REPLY CODE 10AB89 ASEND /D/ 18TYPE,CIRCUIT,OUTPUT OUTPUT CIRCUIT TYPE INDICATES THE TYPE OF OUTPUT CIRCUIT. SELECT REPLY CODE 10AG89 ASEPF /D/T10RANGE IN HERTZ,FREQUENCY,INPUT SWITCHING INPUT SWITCHING FREQUENCY RANGE IN HERTZ THE RANGE OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE INPUT SWITCHING OF THE ITEM IS RATED. 1F MODE REPLY 0 ASEQF /D/T10RANGE IN HERTZ,FREQUENCY,OUTPUT SWITCHING OUTPUT SWITCHING FREQUENCY RANGE IN HERTZ THE RANGE OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE OUTPUT SWITCHING OF THE ITEM IS RATED. 1F MODE REPLY 0 ASERJ 10VOLTAGE RATING,MAXIMUM,RESISTOR RESISTOR MAXIMUM VOLTAGE RATING THE MAXIMUM VOLTAGE RATING FOR WHICH THE RESISTOR IS DESIGNED. 1D AND 1B MODE REPLY11AB63 ASESJ 10CURRENT RATING,HEATER HEATER CURRENT RATING THE AMOUNT OF CURRENT AT WHICH THE HEATER IS RATED. 2D AND 1B MODE REPLY21AC301AC20 ASETD 07FEATURE,COMPRESSION,ROLL ROLL COMPRESSION FEATURE AN INDICATION OF WHETHER OR NOT THE ROLL IS COMPRESSED. SELECT REPLY CODE 10AL75 ASEWD 18TYPE,FOLD,SHEET SHEET FOLD TYPE INDICATES THE TYPE OF SHEET FOLD/S/ PROVIDED. SELECT REPLY CODE 10AL76 ASEXD 19HARDNESS RATING,COATING COATING HARDNESS RATING THE RELATIVE HARDNESS RATING OF THE COATING. SELECT REPLY CODE 10AH10 ASEYD 19PROCESS,WAX WAX PROCESS AN INDICATION OF THE WAXING PROCESS OF THE ITEM. SELECT REPLY CODE 10AA62 ASEZD /D/ 07TREATMENT,OIL OIL TREATMENT AN INDICATION OF WHETHER OR NOT AN OIL TREATMENT IS INCLUDED. SELECT REPLY CODE 10AA49 ASFAD 08LOCATION,MATERIAL,SELF-ADHERING SELF-ADHERING MATERIAL LOCATION INDICATES THE LOCATION OF THE ITEM TO WHICH THE SELF-ADHERING MATERIAL HAS BEEN APPLIED. SELECT REPLY CODE 10AJ91 ASFBD 05DIRECTION,GRAIN GRAIN DIRECTION AN INDICATION OF THE GRAIN DIRECTION. SELECT REPLY CODE 10AA38 ASFCD /D/ 07CONTROL,HYDRAULIC HYDRAULIC CONTROL AN INDICATION OF WHETHER OR NOT A HYDRAULIC CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 ASFDD /D/ 07BYPASS,VACUUM VACUUM BYPASS AN INDICATION OF WHETHER OR NOT A VACUUM BYPASS IS INCLUDED. SELECT REPLY CODE 10AA49 ASFED /D/ 07CONTROL,SPARK SPARK CONTROL AN INDICATION OF WHETHER OR NOT A SPARK CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 ASFFD 18TYPE,CONTROL,SPEED SPEED CONTROL TYPE INDICATES THE TYPE OF SPEED CONTROL FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL77 ASFGJ 04LENGTH,CARTRIDGE CARTRIDGE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CARTRIDGE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ASFHJ 04LENGTH,LEAD LEAD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A LEAD,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ASFJD /D/ 07CONNECTION FOR SECONDARY LEAD,TIP,JACK/PLUG JACK/PLUG TIP CONNECTION FOR SECONDARY LEAD AN INDICATION OF WHETHER OR NOT A JACK AND/OR PLUG TIP CONNECTION/S/ FOR SECONDARY LEAD/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 ASFKA 12QUANTITY,OUTLET,BRASS ELECTRODE BRASS ELECTRODE OUTLET QUANTITY THE NUMBER OF OUTLETS IN THE BRASS ELECTRODE. 1A MODE REPLY 0 ASFLA 12QUANTITY,OUTLET,CARBON ELECTRODE CARBON ELECTRODE OUTLET QUANTITY THE NUMBER OF OUTLETS IN THE CARBON ELECTRODE. 1A MODE REPLY 0 ASFMD /D/ 07SWITCH,CONTROL,HEAT HEAT CONTROL SWITCH AN INDICATION OF WHETHER OR NOT A HEAT CONTROL SWITCH IS INCLUDED. SELECT REPLY CODE 10AA49 ASFNB 10WATTAGE RATING IN WATTS,MAXIMUM,IRON FOR WHICH DESIGNED IRON FOR WHICH DESIGNED MAXIMUM WATTAGE RATING IN WATTS THE MAXIMUM RATED POWER THE IRON FOR WHICH THE ITEM IS DESIGNED CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS. 1B MODE REPLY 0 ASFPD /D/ 09MATERIAL,DEVICE,HOLDING HOLDING DEVICE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HOLDING DEVICE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ASFQD /D/ 07CUP,CLEANER,TIP TIP CLEANER CUP AN INDICATION OF WHETHER OR NOT A TIP CLEANER CUP IS INCLUDED. SELECT REPLY CODE 10AA49 ASFRJ /D/ 10CAPACITY,POT,MELTING,SOLDER SOLDER MELTING POT CAPACITY THE RATED CAPACITY OF THE SOLDER MELTING POT. 1D AND 1B MODE REPLY12AB16 ASFSD /D/ 07ACCOMMODATION,TIPLET TIPLET ACCOMMODATION AN INDICATION OF WHETHER OR NOT A TIPLET ACCOMMODATION IS INCLUDED. SELECT REPLY CODE 10AA49 ASFTJ 04DIAMETER FOR WHICH DESIGNED,TIPLET TIPLET DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TIPLET FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ASFWL 16STYLE,END,TIP TIP END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TIP END. 1L MODE REPLY 0 ASFXJ 04WIDTH,TIP TIP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A TIP,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ASFYB 10INTENSITY,CANDLEPOWER CANDLEPOWER INTENSITY THE MEASUREMENT OF LUMINOUS INTENSITY,EXPRESSED IN CANDLEPOWER. 1B MODE REPLY 0 ASFZG 10TIME,BURNING,ILLUMINANT ILLUMINANT BURNING TIME A MEASUREMENT INDICATING THE BURNING TIME OF THE ILLUMINANT. FULL TEXT WRITE-IN 0 ASGAD /D/ 07BAND,SUSPENSION SUSPENSION BAND AN INDICATION OF WHETHER OR NOT A SUSPENSION BAND(S) IS INCLUDED. SELECT REPLY CODE 10AA49 ASGBD /D/ 07SHIELD,GLARE,BOMBARDIER BOMBARDIER GLARE SHIELD AN INDICATION OF WHETHER OR NOT A BOMBARDIER GLARE SHIELD IS INCLUDED. SELECT REPLY CODE 10AA49 ASGCD /D/ 09MATERIAL,CASE,OUTER OUTER CASE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE OUTER CASE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ASGDD 01COLOR,ILLUMINANT ILLUMINANT COLOR THE HUE OR TINT OF THE ILLUMINANT. SELECT REPLY CODE 10AD06 ASGED /D/ 07SUPPORT,PARACHUTE PARACHUTE SUPPORT AN INDICATION OF WHETHER OR NOT A PARACHUTE SUPPORT IS INCLUDED. SELECT REPLY CODE 10AA49 ASGFD 01COLOR,TRACER TRACER COLOR THE HUE OR TINT OF THE TRACER. SELECT REPLY CODE 10AD06 ASGGD 11METHOD,PROJECTION PROJECTION METHOD THE MEANS BY WHICH THE ITEM IS PROJECTED. SELECT REPLY CODE 10AL78 ASGHD /D/ 07CARTRIDGE,GRENADE GRENADE CARTRIDGE AN INDICATION OF WHETHER OR NOT A GRENADE CARTRIDGE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 ASGJG /D/ 18TYPE/MODEL NUMBER AND QUANTITY,CARTRIDGE,GRENADE GRENADE CARTRIDGE TYPE/MODEL NUMBER AND QUANTITY INDICATES THE TYPE OF GRENADE CARTRIDGE,THE MODEL NUMBER,AND THE NUMBER OF EACH. FULL TEXT WRITE-IN 0 ASGKD 01COLOR,SMOKE SMOKE COLOR THE HUE OR TINT OF THE SMOKE. SELECT REPLY CODE 10AD06 ASGLG 10TIME,BURNING,SMOKE SMOKE BURNING TIME A MEASUREMENT INDICATING THE SMOKE BURNING TIME. FULL TEXT WRITE-IN 0 ASGMD /D/ 07PARACHUTE PARACHUTE AN INDICATION OF WHETHER OR NOT A PARACHUTE IS INCLUDED. SELECT REPLY CODE 10AA49 ASGNG 19MIXTURE,FUEL FUEL MIXTURE AN INDICATION OF THE FUEL MIXTURE. FULL TEXT WRITE-IN 0 ASGPG 19MIXTURE,SMOKE SMOKE MIXTURE AN INDICATION OF THE SMOKE MIXTURE. FULL TEXT WRITE-IN 0 ASGQD 18TYPE,DEVICE,IGNITING IGNITING DEVICE TYPE INDICATES THE TYPE OF DEVICE USED TO IGNITE THE ITEM. SELECT REPLY CODE 10AK32 ASGRD 18TYPE,FILLER FILLER TYPE INDICATES THE TYPE OF FILLER CONTAINED IN THE ITEM. SELECT REPLY CODE 10AL79 ASGSD 18TYPE,DYE DYE TYPE INDICATES THE TYPE OF DYE CONTAINED IN THE ITEM. SELECT REPLY CODE 10AL79 ASGTB 10PERCENTAGE,DYE,FLUORESCEIN FLUORESCEIN DYE PERCENTAGE THE PERCENTAGE OF FLUORESCEIN DYE IN THE ITEM. 1B MODE REPLY 0 ASGWJ 10WEIGHT,DYE DYE WEIGHT A RELATIVE MEASURE OF THE MASS OF THE DYE. 1D AND 1B MODE REPLY12AB16 ASGXD 01COLOR,DYE,WET WET DYE COLOR THE HUE OR TINT OF THE DYE WHEN WET. SELECT REPLY CODE 10AD06 ASGYG 10TIME,BURNING BURNING TIME A MEASUREMENT INDICATING THE BURNING TIME. FULL TEXT WRITE-IN 0 ASGZD 18TYPE,CHARGE,BURSTING BURSTING CHARGE TYPE INDICATES THE TYPE OF BURSTING CHARGE PROVIDED. SELECT REPLY CODE 10AF53 ASHAA 12QUANTITY,BOX,BUTTERFLY VALVE BUTTERFLY VALVE BOX QUANTITY THE NUMBER OF BUTTERFLY VALVE BOXES USED ON THE ITEM. 1A MODE REPLY 0 ASHBA 12QUANTITY PER BOX,BARREL BARREL QUANTITY PER BOX THE NUMBER OF BARRELS INCLUDED IN EACH BOX. 1A MODE REPLY 0 ASHCJ 04SIZE,SAE,MOUNTING FLANGE MOUNTING FLANGE SAE SIZE THE MOUNTING FLANGE SOCIETY OF AUTOMOTIVE ENGINEERS SIZE USED ON THE ITEM. 1D AND 1B MODE REPLY11AA05 ASHDD /D/ 07LEVER FOR MANUAL OPERATION LEVER FOR MANUAL OPERATION AN INDICATION OF WHETHER OR NOT A LEVER FOR MANUAL OPERATION IS INCLUDED. SELECT REPLY CODE 10AA49 ASHEB /D/ 10CAPACITY IN POUNDS PER SQUARE INCH,PRESSURE,DISCHARGE DISCHARGE PRESSURE CAPACITY IN POUNDS PER SQUARE INCH THE MEASURED DISCHARGE PRESSURE CAPACITY FOR WHICH THE ITEM IS RATED,EXPRESSED IN POUNDS PER SQUARE INCH. 1B MODE REPLY 0 ASHFB /D/ 10CAPACITY IN GALLONS PER MINUTE,WATER WATER CAPACITY IN GALLONS PER MINUTE THE MEASURED AMOUNT OF WATER THE ITEM CAN PUMP,EXPRESSED IN GALLONS PER MINUTE. 1B MODE REPLY 0 ASHGJ 04SIZE,CONNECTION,VALVE VALVE CONNECTION SIZE DESIGNATES THE SIZE OF THE VALVE CONNECTION INCLUDED ON THE ITEM. 1D AND 1B MODE REPLY11AA05 ASHHJ 04SIZE ACCOMMODATED,PIPE,NOMINAL,DISCHARGE DISCHARGE NOMINAL PIPE SIZE ACCOMMODATED THE DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE DISCHARGE WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 ASHJD 18TYPE,CONNECTION,DISCHARGE DISCHARGE CONNECTION TYPE INDICATES THE TYPE OF DISCHARGE CONNECTION. SELECT REPLY CODE 10AB76 ASHKB 10HORSEPOWER RATING,MOTOR,ELECTRIC ELECTRIC MOTOR HORSEPOWER RATING THE RATED HORSEPOWER OF THE ELECTRIC MOTOR. 1B MODE REPLY 0 ASHLB 10RPM,MOTOR,ELECTRIC ELECTRIC MOTOR RPM THE SPEED OF THE ELECTRIC MOTOR,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 ASHMD 18TYPE,VALVE VALVE TYPE INDICATES THE TYPE OF VALVE. SELECT REPLY CODE 10AL80 ASHNA 19NUMBER,JOINT COMMITTEE ON PRINTING,UNITED STATES UNITED STATES JOINT COMMITTEE ON PRINTING NUMBER THE IDENTIFICATION NUMBER ASSIGNED BY THE JOINT COMMITTEE ON PRINTING /JCP/ WHICH IDENTIFIES PAPER ITEMS FOR GOVERNMENT USE. 1A MODE REPLY 0 ASHPB /D/ 10STRENGTH IN POUNDS,BREAKING,WARP DIRECTION WARP DIRECTION BREAKING STRENGTH IN POUNDS THE GREATEST LONGITUDINAL STRESS AN ITEM CAN BEAR WITHOUT TEARING APART IN WARP DIRECTION,EXPRESSED IN POUNDS. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1B MODE REPLY 0 ASHQA /D/ 12QUANTITY PER LINEAR INCH,HOOK HOOK QUANTITY PER LINEAR INCH THE NUMBER OF HOOKS IN A LINEAR INCH. 1A MODE REPLY 0 ASHRJ 10WEIGHT WEIGHT A RELATIVE MEASURE OF THE MASS OF AN ITEM WITH RESPECT TO ITS DENSITY. 1D AND 1B MODE REPLY12AG69 ASHSD 19POSITION,PRESSURE,WATER,VALVE VALVE WATER PRESSURE POSITION AN INDICATION OF THE VALVE POSITION AGAINST APPLIED WATER PRESSURE. SELECT REPLY CODE 10AC59 ASHTD 19PREVENTION,RETURN,AIR,VALVE VALVE AIR RETURN PREVENTION AN INDICATION OF WHETHER OR NOT THE VALVE IS REQUIRED TO PREVENT THE RETURN OF AIR. SELECT REPLY CODE 10AE40 ASHWD 14SHAPE,VALVE VALVE SHAPE THE PHYSICAL CONFIGURATION OF THE VALVE. SELECT REPLY CODE 10AD07 ASHXB 10CAPACITY IN GALLONS PER HOUR CAPACITY IN GALLONS PER HOUR THE CAPACITY AT WHICH THE ITEM IS RATED,EXPRESSED IN GALLONS PER HOUR. 1B MODE REPLY 0 ASHYB 04ANGLE IN DEG,SPRAY SPRAY ANGLE IN DEG THE SPRAY ANGLE FOR WHICH THE ITEM IS DESIGNED,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ASHZD 18TYPE,SPRAY SPRAY TYPE INDICATES THE TYPE OF SPRAY FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL82 ASJAD /D/ 07PROVISION,STRAINER STRAINER PROVISION AN INDICATION OF WHETHER OR NOT A STRAINER PROVISION IS INCLUDED. SELECT REPLY CODE 10AA49 ASJBJ 04LENGTH,STRAINER STRAINER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A STRAINER,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 ASJCA 04SIZE,MESH,STRAINER STRAINER MESH SIZE A NUMERIC VALUE WHICH REPRESENTS THE NUMBER OF OPENINGS PER LINEAL INCH OF A STRAINER. 1A MODE REPLY 0 ASJDD /D/ 09MATERIAL,STRAINER STRAINER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH A STRAINER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ASJEJ 04LENGTH,FILTER FILTER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A FILTER,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 ASJFB /D/ 04SIZE IN INCHES,OPENING,FILTER DISC FILTER DISC OPENING SIZE IN INCHES THE DISC OPENING SIZE OF A FILTER,EXPRESSED IN INCHES. 1B MODE REPLY 0 ASJGD /D/ 07ADAPTER ADAPTER AN INDICATION OF WHETHER OR NOT AN ADAPTER IS INCLUDED. SELECT REPLY CODE 10AA49 ASJHJ 04LENGTH,ADAPTER ADAPTER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ADAPTER,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 ASJJD /D/ 13THREAD LOCATION,CONNECTION,ADAPTER INLET ADAPTER INLET CONNECTION THREAD LOCATION INDICATES THE THREAD LOCATION OF THE ADAPTER INLET CONNECTION. SELECT REPLY CODE 10AJ91 ASJKA /D/ 13THREAD SIZE,CONNECTION,ADAPTER INLET ADAPTER INLET CONNECTION THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER INCH OF THE ADAPTER INLET CONNECTION. 1A MODE REPLY 0 ASJLD 13THREAD SERIES,CONNECTION,ADAPTER INLET ADAPTER INLET CONNECTION THREAD SERIES A DESIGNATION OF THE ADAPTER INLET CONNECTION IDENTIFYING THREAD SERIES. SELECT REPLY CODE 10AH06 ASJMG /D/ 19SPECIFICATION/D/,TENTATIVE,ORIGINATING,GOVERNMENT AGENCY GOVERNMENT AGENCY ORIGINATING TENTATIVE SPECIFICATION/D/ THE NAME OF THE GOVERNMENT AGENCY ORIGINATING THE TENTATIVE SPECIFICATION. FULL TEXT WRITE-IN 0 ASJNG /D/ 03DESIGNATOR,SPECIFICATION,TENTATIVE,GOVERNMENT AGENCY GOVERNMENT AGENCY TENTATIVE SPECIFICATION DESIGNATOR THE NAME OF THE GOVERNMENT AGENCY CONTROLLING THE TENTATIVE SPECIFICATION DESIGNATOR. FULL TEXT WRITE-IN 0 ASJPJ /D/ 04LENGTH,ISSUE ISSUE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF ANY OBJECT OF ISSUE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ASJQD /D/ 09MATERIAL,SHANK SHANK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHANK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ASJRD 07REMOVABILITY,FRAME FRAME REMOVABILITY AN INDICATION OF THE REMOVABILITY OF THE FRAME. SELECT REPLY CODE 10AC29 ASJSA 12QUANTITY,GRILLE GRILLE QUANTITY THE NUMBER OF GRILLES CONTAINED IN THE ITEM. 1A MODE REPLY 0 ASJTD 07COLOR,FLAME FLAME COLOR THE HUE OR TINT OF THE FLAME. SELECT REPLY CODE 10AD06 ASJWJ 10TEMP,MINIMUM,IGNITION IGNITION MINIMUM TEMP THE MINIMUM TEMPERATURE REQUIRED FOR THE ITEM TO IGNITE. 1D AND 1B MODE REPLY11AB36 ASJXD /D/ 07FEATURE,BURNING,ADVERSE WEATHER ADVERSE WEATHER BURNING FEATURE AN INDICATION OF WHETHER OR NOT AN ADVERSE WEATHER BURNING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ASJYD 11METHOD,EJECTION,CONTENT CONTENT EJECTION METHOD THE MEANS BY WHICH THE CONTENTS ARE EJECTED. SELECT REPLY CODE 10AL78 ASJZJ A18TYPE AND QUANTITY,STATION STATION TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF STATIONS. 1D AND 1A MODE REPLY13AL81 ASKAJ A19NAME AND QUANTITY,COMPONENT COMPONENT NAME AND QUANTITY THE NAME AND NUMBER OF COMPONENTS INCLUDED. 1D AND 1A MODE REPLY13AL83 ASKBA 19NUMBER,MODEL,COMPONENT COMPONENT MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE COMPONENT. 1A MODE REPLY 0 ASKCA 12QUANTITY,POINT,SUSPENSION,LOAD LOAD SUSPENSION POINT QUANTITY THE NUMBER OF LOAD SUSPENSION POINTS. 1A MODE REPLY 0 ASKDJ 04DISTANCE BETWEEN LOAD SUSPENSION POINTS DISTANCE BETWEEN LOAD SUSPENSION POINTS THE DISTANCE BETWEEN THE LOAD SUSPENSION POINTS. 2D AND 1B MODE REPLY21AA051AC20 ASKEA 19NUMBER,MODEL,DISPENSER DISPENSER MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE DISPENSER. 1A MODE REPLY 0 ASKFG /D/ 04SIZE AND MODEL NUMBER,PROJECTILE,CHEMICAL CHEMICAL PROJECTILE SIZE AND MODEL NUMBER THE SIZE AND MODEL NUMBER OF THE CHEMICAL PROJECTILE. FULL TEXT WRITE-IN 0 ASKGG /D/ 04SIZE AND MODEL NUMBER,CLUSTER,CANISTER CANISTER CLUSTER SIZE AND MODEL NUMBER THE SIZE AND MODEL NUMBER OF THE CANISTER CLUSTER. FULL TEXT WRITE-IN 0 ASKHA /D/ 19NUMBER,MODEL,PACKAGE PACKAGE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE PACKAGE. PLEASE USE MRC AMWN IN PLACE OF THIS DISCONTINUED MRC. 1A MODE REPLY 0 ASKJA 19SYMBOL,CHEMICAL CORPS CHEMICAL CORPS SYMBOL THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED CHEMICAL CORPS SYMBOL. 1A MODE REPLY 0 ASKKA /D/ 12QUANTITY,SPOT,DESICCANT DESICCANT SPOT QUANTITY THE NUMBER OF DESICCANT SPOTS PROVIDED. 1A MODE REPLY 0 ASKLA /D/ 12QUANTITY,TOTAL,MARKING MARKING TOTAL QUANTITY THE TOTAL NUMBER OF MARKINGS ON THE ITEM. 1A MODE REPLY 0 ASKMA /D/ 12QUANTITY,MARKING,INDIVIDUAL INDIVIDUAL MARKING QUANTITY THE NUMBER OF INDIVIDUAL MARKINGS ON THE ITEM. 1A MODE REPLY 0 ASKNG 19MARKING,INDIVIDUAL INDIVIDUAL MARKING AN INDICATION OF THE INDIVIDUAL MARKING ON THE ITEM. FULL TEXT WRITE-IN 0 ASKPD 01COLOR,MARKING MARKING COLOR THE HUE OR TINT OF THE MARKING(S). SELECT REPLY CODE 10AD06 ASKQD 19USE,SPECIFIC,MARKING COLOR MARKING COLOR SPECIFIC USE THE SPECIFIC USE OF THE MARKING COLOR. SELECT REPLY CODE 10AL84 ASKRJ 04LENGTH,WINDOW WINDOW LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE WINDOW,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ASKSJ 04HEIGHT,WINDOW WINDOW HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE WINDOW,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 ASKTJ 04WIDTH,WINDOW WINDOW WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE WINDOW,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ASKWJ /D/ 04DIAMETER,WINDOW WINDOW DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR WINDOW,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ASKXA 12QUANTITY,CONNECTION,ELECTRICAL ELECTRICAL CONNECTION QUANTITY THE NUMBER OF ELECTRICAL CONNECTIONS PROVIDED. 1A MODE REPLY 0 ASKYG /D/ 19AGENCY,CONTROLLING,ELECTRICAL CONNECTION ELECTRICAL CONNECTION CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE ELECTRICAL CONNECTION. PLEASE USE MRC BLJN IN PLACE OF THIS DISCONTINUED MRC. FULL TEXT WRITE-IN 0 ASKZG 19NUMBER,IDENTIFYING,ELECTRICAL CONNECTION ELECTRICAL CONNECTION IDENTIFYING NUMBER THE IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE ELECTRICAL CONNECTION. FULL TEXT WRITE-IN 0 ASLAD /D/ 07CASE,SEALED,HERMETICALLY HERMETICALLY SEALED CASE AN INDICATION OF WHETHER OR NOT A HERMETICALLY SEALED CASE IS INCLUDED. SELECT REPLY CODE 10AA49 ASLBA 12QUANTITY,SIGN,COMMAND COMMAND SIGN QUANTITY THE NUMBER OF COMMAND SIGNS PROVIDED. 1A MODE REPLY 0 ASLCD 07REPLACEABILITY,SIGN,COMMAND COMMAND SIGN REPLACEABILITY AN INDICATION OF WHETHER OR NOT THE COMMAND SIGN/S/ IS REPLACEABLE. SELECT REPLY CODE 10AG84 ASLDD /D/ 07FEATURE,REFILLABLE REFILLABLE FEATURE AN INDICATION OF WHETHER OR NOT A REFILLABLE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ASLEB 10CAPACITY IN GRAMS CAPACITY IN GRAMS AN INDICATION OF THE CAPACITY OF THE ITEM,EXPRESSED IN GRAMS. 1B MODE REPLY 0 ASLFD /D/ 07PROVISION,FREQUENCY,INPUT TEST INPUT TEST FREQUENCY PROVISION AN INDICATION OF WHETHER OR NOT A PROVISION/S/ FOR INPUT TEST FREQUENCY IS INCLUDED. SELECT REPLY CODE 10AA49 ASLGJ /D/ 10FREQUENCY RATING,TEST,INPUT INPUT TEST FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE INPUT TEST IS RATED. 2D AND 1B MODE REPLY21AC321AC20 ASLHG /D/ 19INFORMATION,DISPLAYED DISPLAYED INFORMATION THE INFORMATION DISPLAYED ON THE ITEM. FULL TEXT WRITE-IN 0 ASLJA 12QUANTITY,INDICATOR INDICATOR QUANTITY THE NUMBER OF INDICATORS PROVIDED. 1A MODE REPLY 0 ASLKG /D/ 19AGENCY,CONTROLLING,INDICATOR INDICATOR CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE INDICATOR. FULL TEXT WRITE-IN 0 ASLLG /D/ 19NAME ASSIGNED BY CONTROLLING AGENCY,ITEM,INDICATOR INDICATOR ITEM NAME ASSIGNED BY CONTROLLING AGENCY THE NAME OF THE INDICATOR ASSIGNED BY THE CONTROLLING AGENCY. FULL TEXT WRITE-IN 0 ASLMG /D/ 19NUMBER,IDENTIFYING,INDICATOR INDICATOR IDENTIFYING NUMBER THE IDENTIFYING NUMBER OF THE INDICATOR ASSIGNED BY THE CONTROLLING AGENCY. FULL TEXT WRITE-IN 0 ASLNJ 10CURRENT RATING IN AMPS,FUSE FUSE CURRENT RATING IN AMPS THE VALUE OF CURRENT FOR WHICH THE FUSE IS RATED,EXPRESSED IN AMPERES. 1D AND 1B MODE REPLY11AC20 ASLPD 14SHAPE,OPENING,GRILLE WIRE MESH GRILLE WIRE MESH OPENING SHAPE THE PHYSICAL CONFIGURATION OF THE GRILLE WIRE MESH OPENING. SELECT REPLY CODE 10AD07 ASLQJ /D/ 04SIZE,MESH MESH SIZE THE ALPHA AND/OR NUMERIC SIZE DESIGNATION BY WHICH THE MESH IS IDENTIFIED. 1D AND 1B MODE REPLY11AA05 ASLRA /D/ 19NUMBER,SIZE,WIRE WIRE SIZE NUMBER AN INDICATION OF THE WIRE SIZE NUMBER. 1A MODE REPLY 0 ASLSD 14SHAPE,WIRE WIRE SHAPE THE PHYSICAL CONFIGURATION OF THE WIRE. SELECT REPLY CODE 10AD07 ASLTD 14SHAPE,PERFORATED,GRILLE GRILLE PERFORATED SHAPE THE PHYSICAL CONFIGURATION OF THE GRILLE PERFORATION. SELECT REPLY CODE 10AD07 ASLWB /D/ 10PERCENT,AREA,OPEN OPEN AREA PERCENT AN INDICATION OF THE PERCENTAGE OF OPEN AREA. 1B MODE REPLY 0 ASLXA 04SIZE,GAGE,METAL METAL GAGE SIZE DESIGNATES THE METAL GAGE SIZE. 1A MODE REPLY 0 ASLYD 19POSITION,BAR,GRILLE GRILLE BAR POSITION AN INDICATION OF THE POSITION OF THE GRILLE BARS. SELECT REPLY CODE 10AF63 ASLZB 04SPACING IN INCHES,BAR BAR SPACING IN INCHES A DESIGNATION OF THE SPACING OF THE BARS,EXPRESSED IN INCHES. 1B MODE REPLY 0 ASMAD 07ADJUSTABILITY,BAR BAR ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE BARS ARE ADJUSTABLE. SELECT REPLY CODE 10AB00 ASMBD 11METHOD,ADJUSTMENT,BAR BAR ADJUSTMENT METHOD THE MEANS USED FOR ADJUSTING THE BAR. SELECT REPLY CODE 10AL41 ASMCD 18TYPE,FIN,GRILLE GRILLE FIN TYPE INDICATES THE TYPE OF FINS PROVIDED WITH THE GRILLE. SELECT REPLY CODE 10AF63 ASMDJ 04SPACING,FIN FIN SPACING THE SPACING OF THE FINS. 1D AND 1B MODE REPLY11AA05 ASMEJ 04THICKNESS,FIN FIN THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE FIN,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 ASMFJ 04SPACING,BAR,FIN SUPPORT FIN SUPPORT BAR SPACING AN INDICATION OF THE FIN SUPPORT BAR SPACING. 1D AND 1B MODE REPLY11AA05 ASMGD 11METHOD,OPERATING,DEFLECTOR BLADE DEFLECTOR BLADE OPERATING METHOD THE MEANS BY WHICH THE DEFLECTOR BLADE IS OPERATED. SELECT REPLY CODE 10AC58 ASMHD 19POSITION,AXIS,BLADE VERTICAL SURFACE BLADE VERTICAL SURFACE AXIS POSITION AN INDICATION OF THE BLADE VERTICAL SURFACE AXIS POSITION. SELECT REPLY CODE 10AF63 ASMJJ 04SPACING,BLADE BLADE SPACING THE SPACING BETWEEN THE BLADES. 1D AND 1B MODE REPLY11AA05 ASMKA 04SIZE,GAGE,SHEET METAL SHEET METAL GAGE SIZE DESIGNATES THE SHEET METAL GAGE SIZE. 1A MODE REPLY 0 ASMLD 18TYPE,HOLDER,POSITIONING POSITIONING HOLDER TYPE INDICATES THE TYPE OF POSITIONING HOLDER PROVIDED. SELECT REPLY CODE 10AL85 ASMMA 12QUANTITY,CONNECTION CONNECTION QUANTITY THE NUMBER OF CONNECTIONS FURNISHED. 1A MODE REPLY 0 ASMNJ 04DIAMETER,ATTACHMENT,END END ATTACHMENT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE END ATTACHMENT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ASMPD /D/ 07PUMP,FUEL FUEL PUMP AN INDICATION OF WHETHER OR NOT A FUEL PUMP IS INCLUDED. SELECT REPLY CODE 10AA49 ASMQD 02DESIGN,PUMP PUMP DESIGN THE FUNCTIONAL DESIGN OF THE PUMP. SELECT REPLY CODE 10AL86 ASMRA 19GRADE FOR WHICH DESIGNED,FUEL FUEL GRADE FOR WHICH DESIGNED THE NUMBER USED FOR IDENTIFYING THE FUEL GRADE FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 ASMSJ 10CAPACITY IN GALLONS PER HOUR CAPACITY IN GALLONS PER HOUR THE CAPACITY AT WHICH THE ITEM IS RATED,EXPRESSED IN GALLONS PER HOUR. 1D AND 1B MODE REPLY11AC20 ASMTD 11METHOD,REGULATING,ATOMIZING CUP ATOMIZING CUP REGULATING METHOD THE MEANS BY WHICH THE ATOMIZING CUP IS REGULATED. SELECT REPLY CODE 10AE81 ASMWD 18TYPE,CONTROL,FLAME FLAME CONTROL TYPE INDICATES THE TYPE OF FLAME CONTROL. SELECT REPLY CODE 10AL37 ASMXD 08LOCATION,PUMP,FUEL FUEL PUMP LOCATION INDICATES THE LOCATION OF THE FUEL PUMP. SELECT REPLY CODE 10AJ91 ASMYD /D/ 09MATERIAL,FRAMEWORK FRAMEWORK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FRAMEWORK IS FABRICATED. SELECT REPLY CODE 10AD09 ASMZD /D/ 09MATERIAL,DOOR DOOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE DOOR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ASNAD /D/ 09MATERIAL,GRATE GRATE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE GRATE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ASNBD /D/ 09MATERIAL,FACING,OUTSIDE OUTSIDE FACING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE OUTSIDE FACING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC CZKR IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 ASNCA /D/ 19NUMBER,IDENTIFYING,FAN FAN IDENTIFYING NUMBER THE NUMBER THAT IDENTIFIES THE FAN. 1A MODE REPLY 0 ASNDD 18TYPE,DRAFT DRAFT TYPE INDICATES THE TYPE OF DRAFT FOR WHICH DESIGNED. SELECT REPLY CODE 10AL51 ASNEA /D/ 19NAME,BLOWER BLOWER NAME THE NAME ASSIGNED TO THE BLOWER. 1A MODE REPLY 0 ASNFD 18TYPE,BLOWER BLOWER TYPE INDICATES THE TYPE OF BLOWER PROVIDED. SELECT REPLY CODE 10AL87 ASNGA /D/ 19NUMBER,MODEL,BLOWER BLOWER MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE BLOWER. 1A MODE REPLY 0 ASNHG /D/ 19NAME,ENGINE ENGINE NAME THE NAME ASSIGNED TO THE ENGINE. FULL TEXT WRITE-IN 0 ASNJB /D/ 10VOLTAGE RATING IN VOLTS,MAXIMUM,FUSE FUSE MAXIMUM VOLTAGE RATING IN VOLTS THE MAXIMUM VOLTAGE RATING AT WHICH THE FUSE IS DESIGNED TO OPERATE,EXPRESSED IN VOLTS. 1B MODE REPLY 0 ASNKF /D/T10RANGE IN DEG CELSIUS,SCALE,DIAL DIAL SCALE RANGE IN DEG CELSIUS THE MINIMUM AND MAXIMUM SCALE RANGE OF THE DIAL,EXPRESSED IN DEGREES CELSIUS. 1F MODE REPLY 0 ASNLA /D/ 16STYLE,METER METER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE BASIC APPEARANCE OF THE METER. 1A MODE REPLY 0 ASNMD /D/ 07SIGNAL,OVER-TEMPERATURE,EXCESSIVE EXCESSIVE OVER-TEMPERATURE SIGNAL AN INDICATION OF WHETHER OR NOT AN EXCESSIVE OVER-TEMPERATURE SIGNAL IS INCLUDED. SELECT REPLY CODE 10AA49 ASNNJ 04DEPTH TO PANEL DEPTH TO PANEL NONE. 2D AND 1B MODE REPLY21AA051AC20 ASNPJ /D/ 04DEPTH BEHIND MOUNTING FLANGE DEPTH BEHIND MOUNTING FLANGE A MEASUREMENT BETWEEN THE MOUNTING FLANGE AND THE EXTREMITY OF THE ITEM,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 ASNQJ /D/ 04DIAMETER BEHIND MOUNTING FLANGE,BODY BODY DIAMETER BEHIND MOUNTING FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 ASNRJ /D/ 04LENGTH BEHIND MOUNTING FLANGE,BODY BODY LENGTH BEHIND MOUNTING FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 ASNSJ /D/ 04WIDTH BEHIND MOUNTING FLANGE,BODY BODY WIDTH BEHIND MOUNTING FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 ASNTJ 04DEPTH TO MOUNTING FLANGE DEPTH TO MOUNTING FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 ASNWJ 04HEIGHT,SIGHT SIGHT HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 ASNXJ 04DIAMETER,SIGHT SIGHT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ASNYJ /D/ 04DISTANCE,CENTER TO FACE CENTER TO FACE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 ASNZJ 04DISTANCE BETWEEN VALVES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN VALVES THE CENTER TO CENTER DISTANCE BETWEEN VALVES. 2D AND 1B MODE REPLY21AA051AC20 ASPAG 03DESIGNATION,TRADE,CATHODE RAY TUBE CATHODE RAY TUBE TRADE DESIGNATION THE DESIGNATION BY WHICH THE CATHODE RAY TUBE IS IDENTIFIED THROUGHOUT INDUSTRY. FULL TEXT WRITE-IN 0 ASPBG /D/ 19DIMENSION,DIAL DIAL DIMENSION THE DIMENSION/S/ OF THE DIAL. FULL TEXT WRITE-IN 0 ASPCA 12QUANTITY,POINTER POINTER QUANTITY THE NUMBER OF POINTERS INCLUDED. 1A MODE REPLY 0 ASPDD 19FINISH,POINTER POINTER FINISH AN INDICATION OF THE FINISH ON THE POINTER. SELECT REPLY CODE 10AB54 ASPEG 19MARKING,POINTER POINTER MARKING AN INDICATION OF THE MARKING/S/ ON THE POINTER. FULL TEXT WRITE-IN 0 ASPFG /D/ 10RANGE,PRESENTATION,SCALE SCALE PRESENTATION RANGE AN INDICATION OF THE PRESENTATION RANGE OF THE SCALE. FULL TEXT WRITE-IN 0 ASPGH /D/ 19MARKING AND SURFACE FINISH,SCALE SCALE MARKING AND SURFACE FINISH AN INDICATION OF THE MARKING/S/ ON THE SCALE AND THE SURFACE FINISH. PLEASE USE MRC ABFN IN PLACE OF THIS DISCONTINUED MRC. 2D MODE REPLY 23AJ653AB54 ASPHD 01COLOR,BACKGROUND,SCALE SCALE BACKGROUND COLOR THE HUE OR TINT OF THE BACKGROUND OF THE SCALE. SELECT REPLY CODE 10AD06 ASPJJ /D/ 04DIAMETER,FACILITY,VIEWING VIEWING FACILITY DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE VIEWING FACILITY,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ASPKD 18TYPE,SCAN,CATHODE RAY TUBE CATHODE RAY TUBE SCAN TYPE INDICATES THE TYPE OF SCAN FOR WHICH THE CATHODE RAY TUBE IS DESIGNED. SELECT REPLY CODE 10AJ15 ASPLA /D/ 12QUANTITY FOR WHICH DESIGNED,PHASE PHASE QUANTITY FOR WHICH DESIGNED THE NUMBER OF PHASES FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 ASPMA 12QUANTITY,ROD,GUARD GUARD ROD QUANTITY THE NUMBER OF GUARD RODS INCLUDED. 1A MODE REPLY 0 ASPND /D/ 07INDICATOR,CONTENT,MOISTURE MOISTURE CONTENT INDICATOR AN INDICATION OF WHETHER OR NOT A MOISTURE CONTENT INDICATOR IS INCLUDED. SELECT REPLY CODE 10AA49 ASPPJ 04DIAMETER FOR WHICH DESIGNED,OUTSIDE,TUBE TUBE OUTSIDE DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBE FOR WHICH DESIGNED,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ASPQJ 04RADIUS,SEAT SEAT RADIUS THE RADIUS OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS. 1D AND 1B MODE REPLY11AA05 ASPRD /D/ 07FEATURE,SHUTOFF,AUTOMATIC AUTOMATIC SHUTOFF FEATURE AN INDICATION OF WHETHER OR NOT AN AUTOMATIC SHUTOFF FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ASPSD /D/ 07VALVE,SHUTOFF SHUTOFF VALVE AN INDICATION OF WHETHER OR NOT A SHUTOFF VALVE/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 ASPTD /D/ 07CAP,SEAL,PORT PORT SEAL CAP AN INDICATION OF WHETHER OR NOT A PORT SEAL CAP/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 ASPWD /D/ 18TYPE,ADAPTER,COUPLING COUPLING ADAPTER TYPE INDICATES THE TYPE OF COUPLING ADAPTER PROVIDED. SELECT REPLY CODE 10AC42 ASPXG 19NAME,SCALE SCALE NAME THE NOMENCLATURE BY WHICH THE SCALE IS IDENTIFIED. FULL TEXT WRITE-IN 0 ASPYH 19MARKING AND COLOR,SCALE,NONLUMINOUS NONLUMINOUS SCALE MARKING AND COLOR AN INDICATION OF THE NONLUMINOUS MARKING/S/ ON THE SCALE AND THE COLOR. 2D MODE REPLY 23AJ656AD06 ASPZD /D/ 18TYPE,CONNECTION,ELECTRICAL ELECTRICAL CONNECTION TYPE INDICATES THE TYPE OF ELECTRICAL CONNECTION INCLUDED ON THE ITEM. SELECT REPLY CODE 10AK93 ASQAA /D/ 13THREAD SIZE,STUD,TERMINAL TERMINAL STUD THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A TERMINAL STUD. 1A MODE REPLY 0 ASQBJ 04LENGTH,OVERALL,CABLE ASSEMBLY CABLE ASSEMBLY OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CABLE ASSEMBLY. 2D AND 1B MODE REPLY21AA051AC20 ASQCG /D/ 19ADDRESS,AGENCY,CONTROLLING,ELECTRICAL CONNECTION ELECTRICAL CONNECTION CONTROLLING AGENCY ADDRESS THE ADDRESS OF THE AGENCY CONTROLLING THE ELECTRICAL CONNECTION. FULL TEXT WRITE-IN 0 ASQDD 11METHOD,MATING,CONNECTOR CONNECTOR MATING METHOD THE MEANS BY WHICH THE CONNECTOR MATES WITH ANOTHER. SELECT REPLY CODE 10AH46 ASQED /D/ 07FEATURE,WATERTIGHT WATERTIGHT FEATURE AN INDICATION OF WHETHER OR NOT A WATERTIGHT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ASQFA 19NUMBER,MODEL,ENGINE ENGINE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE ENGINE. 1A MODE REPLY 0 ASQGD /D/ 07COIL,WATER,HOT HOT WATER COIL AN INDICATION OF WHETHER OR NOT A HOT WATER COIL IS INCLUDED. SELECT REPLY CODE 10AA49 ASQHB /D/ 10CAPACITY IN GALLONS PER HOUR,COIL COIL CAPACITY IN GALLONS PER HOUR THE RATED COIL CAPACITY OF THE ITEM,EXPRESSED IN GALLONS PER HOUR. 1B MODE REPLY 0 ASQJF T10RANGE IN DEG CELSIUS,TEMP,OPERATING OPERATING TEMP RANGE IN DEG CELSIUS THE MINIMUM AND MAXIMUM OPERATING TEMPERATURES AT WHICH THE ITEM IS RATED,EXPRESSED IN DEGREES CELSIUS. 1F MODE REPLY 0 ASQKD 11METHOD,CHARGING CHARGING METHOD THE MEANS USED FOR CHARGING THE ITEM. SELECT REPLY CODE 10AL88 ASQLJ 10CAPACITY IN POUNDS PER HOUR CAPACITY IN POUNDS PER HOUR THE RATED CAPACITY OF THE ITEM,EXPRESSED IN POUNDS PER HOUR. 1D AND 1B MODE REPLY11AC20 ASQMD /D/ 07FEATURE,MOUNTED,SKID SKID MOUNTED FEATURE AN INDICATION OF WHETHER OR NOT A SKID MOUNTED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ASQND 02DESIGN,SYSTEM,HEATING HEATING SYSTEM DESIGN THE HEATING SYSTEM FOR WHICH THE UNIT IS DESIGNED. SELECT REPLY CODE 10AA94 ASQPD 18TYPE,BOILER BOILER TYPE INDICATES THE TYPE OF BOILER. SELECT REPLY CODE 10AL89 ASQQB /D/ 10HORSEPOWER RATING HORSEPOWER RATING THE RATED HORSEPOWER OF THE ITEM. PLEASE USE MRC ANCY IN PLACE OF THIS DISCONTINUED MRC. 1B MODE REPLY 0 ASQRD 18TYPE,FIRING FIRING TYPE INDICATES THE TYPE OF FIRING. SELECT REPLY CODE 10AA94 ASQSD /D/ 11METHOD,FIRING,COAL COAL FIRING METHOD THE MEANS USED FOR COAL FIRING. SELECT REPLY CODE 10AL88 ASQTB /D/ 10AREA IN SQUARE FEET,GRATE GRATE AREA IN SQUARE FEET A MEASUREMENT OF THE GRATE AREA,EXPRESSED IN SQUARE FEET. 1B MODE REPLY 0 ASQWD 18TYPE,BURNER,OIL OIL BURNER TYPE INDICATES THE TYPE OF OIL BURNER. SELECT REPLY CODE 10AA96 ASQXA 19OIL FOR WHICH DESIGNED OIL FOR WHICH DESIGNED THE OIL FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 ASQYD 18TYPE,BURNER,GAS GAS BURNER TYPE INDICATES THE TYPE OF GAS BURNER. SELECT REPLY CODE 10AL90 ASQZD 18TYPE,GAS GAS TYPE INDICATES THE TYPE OF GAS. SELECT REPLY CODE 10AF80 ASRAD /D/ 07FEATURE,INCLOSURE,JACKET JACKET INCLOSURE FEATURE AN INDICATION OF WHETHER OR NOT A JACKET INCLOSURE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ASRBD /D/ 01COLOR,LINER LINER COLOR THE HUE OR TINT OF THE LINER. SELECT REPLY CODE 10AD06 ASRCD /D/ 09MATERIAL,PADDING PADDING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PADDING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ASRDD 18TYPE,CORD CORD TYPE INDICATES THE TYPE OF CORD. SELECT REPLY CODE 10AL76 ASRED 18TYPE,INSULATION INSULATION TYPE INDICATES THE TYPE OF INSULATION. SELECT REPLY CODE 10AL91 ASRFD /D/ 07CHUTE/HOPPER,FEED FEED CHUTE/HOPPER AN INDICATION OF WHETHER OR NOT A FEED CHUTE/HOPPER IS INCLUDED. IF INCLUDEDPLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 ASRGD /D/ 07CONTROLLER CONTROLLER AN INDICATION OF WHETHER OR NOT A CONTROLLER IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 ASRHD 18TYPE,ATOMIZER ATOMIZER TYPE INDICATES THE TYPE OF ATOMIZER. SELECT REPLY CODE 10AL92 ASRJA 12QUANTITY,SLOT,OIL SUPPLY OIL SUPPLY SLOT QUANTITY THE NUMBER OF OIL SUPPLY SLOTS IN THE ITEM. 1A MODE REPLY 0 ASRKD 18TYPE,SEAM SEAM TYPE INDICATES THE TYPE OF SEAM ON THE ITEM. SELECT REPLY CODE 10AL93 ASRLD 19LEVEL,PLAY PLAY LEVEL AN INDICATION OF THE LEVEL OF PLAY FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL94 ASRMD 18TYPE,PLAY PLAY TYPE INDICATES THE TYPE OF PLAY FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL95 ASRND 19HAND FOR WHICH DESIGNED HAND FOR WHICH DESIGNED AN INDICATION OF THE HAND FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL96 ASRPD 18TYPE,TREATMENT,LEATHER LEATHER TREATMENT TYPE INDICATES THE TYPE OF LEATHER TREATMENT PROVIDED. SELECT REPLY CODE 10AK06 ASRQD 19CONSTRUCTION,HEEL HEEL CONSTRUCTION AN INDICATION OF THE CONSTRUCTION OF THE HEEL. SELECT REPLY CODE 10AL98 ASRRD /D/ 07FEATURE,TRAPPER TRAPPER FEATURE AN INDICATION OF WHETHER OR NOT A TRAPPER FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ASRSD /D/ 07FEATURE,BLEACH BLEACH FEATURE AN INDICATION OF WHETHER OR NOT A BLEACH FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ASRTD /D/ 18TYPE,FABRIC FABRIC TYPE INDICATES THE TYPE OF FABRIC PROVIDED. SELECT REPLY CODE 10AF82 ASRWG /D/ 03DESIGNATION,QUANTITY/SIZE,PLY PLY QUANTITY/SIZE DESIGNATION A DESIGNATION INDICATING THE ACTUAL NUMBER OF FULL LAYERS OF PLY MATERIAL AND SIZE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. FULL TEXT WRITE-IN 0 ASRXD 05DIRECTION,TWIST TWIST DIRECTION AN INDICATION OF THE TWIST DIRECTION. SELECT REPLY CODE 10AA38 ASRYA /D/ 12QUANTITY PER INCH,TURN,PLY PLY TURN QUANTITY PER INCH THE NUMBER OF PLY TURNS PER INCH. 1A MODE REPLY 0 ASRZA /D/ 12QUANTITY PER PLY,STRAND STRAND QUANTITY PER PLY THE NUMBER OF STRANDS IN EACH PLY. 1A MODE REPLY 0 ASSAJ 04DIAMETER,CABLE CABLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CABLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ASSBA 12QUANTITY,CONNECTION,MECHANICAL MECHANICAL CONNECTION QUANTITY THE NUMBER OF MECHANICAL CONNECTIONS PROVIDED. 1A MODE REPLY 0 ASSCG 04SIZE,CONNECTION,MECHANICAL MECHANICAL CONNECTION SIZE DESIGNATES THE THREAD SIZE,DIAMETER,OR THE LIKE,OF THE MECHANICAL CONNECTION. FULL TEXT WRITE-IN 0 ASSDD 18TYPE,CONNECTION,MECHANICAL MECHANICAL CONNECTION TYPE INDICATES THE TYPE OF MECHANICAL CONNECTION/S/ PROVIDED. SELECT REPLY CODE 10AJ68 ASSEB /D/ 10VACUUM IN INCHES OF MERCURY VACUUM IN INCHES OF MERCURY THE VACUUM REQUIRED BY THE ITEM,EXPRESSED IN INCHES OF MERCURY. 1B MODE REPLY 0 ASSFD /D/ 07FEATURE,ENCASEMENT ENCASEMENT FEATURE AN INDICATION OF WHETHER OR NOT AN ENCASEMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ASSGD /D/ 07SOCKET,LAMP,INSTRUMENT INSTRUMENT LAMP SOCKET AN INDICATION OF WHETHER OR NOT AN INSTRUMENT LAMP SOCKET(S) IS INCLUDED. SELECT REPLY CODE 10AA49 ASSHD /D/ 07LAMP,INSTRUMENT INSTRUMENT LAMP AN INDICATION OF WHETHER OR NOT AN INSTRUMENT LAMP IS INCLUDED. SELECT REPLY CODE 10AA49 ASSJB /D/ 10VOLTAGE IN VOLTS,LAMP,ILLUMINATING ILLUMINATING LAMP VOLTAGE IN VOLTS THE ELECTRICAL VOLTAGE OF THE ILLUMINATING LAMP,EXPRESSED IN VOLTS. 1B MODE REPLY 0 ASSKA 12QUANTITY,KNOB KNOB QUANTITY THE NUMBER OF KNOBS PROVIDED. 1A MODE REPLY 0 ASSLG 19PURPOSE,KNOB KNOB PURPOSE THE FUNCTION FOR WHICH THE KNOB IS INTENDED. FULL TEXT WRITE-IN 0 ASSMD /D/ 07KNOB,SELECTOR,DIAL DIAL SELECTOR KNOB AN INDICATION OF WHETHER OR NOT A DIAL SELECTOR KNOB IS INCLUDED. SELECT REPLY CODE 10AA49 ASSNG /D/ 19MARKING,KNOB,SELECTOR,DIAL DIAL SELECTOR KNOB MARKING AN INDICATION OF THE MARKINGS/S/ ON THE DIAL SELECTOR KNOB. FULL TEXT WRITE-IN 0 ASSPJ 04DIAMETER,DIAL DIAL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DIAL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ASSQG 19MARKING,DIAL DIAL MARKING AN INDICATION OF THE MARKING/S/ ON THE DIAL. FULL TEXT WRITE-IN 0 ASSRG 19PURPOSE,POINTER POINTER PURPOSE THE FUNCTION FOR WHICH THE POINTER IS INTENDED. FULL TEXT WRITE-IN 0 ASSSD 01COLOR,POINTER POINTER COLOR THE HUE OR TINT OF THE POINTER. SELECT REPLY CODE 10AD06 ASSTD 18TYPE,POINTER POINTER TYPE INDICATES THE TYPE OF POINTER PROVIDED. SELECT REPLY CODE 10AL97 ASSWJ /D/ 04SIZE,BODY,PANEL MOUNTED PANEL MOUNTED BODY SIZE THE DIMENSION OF THE BODY TO BE MOUNTED ON THE PANEL. 2D AND 1B MODE REPLY21AA051AC20 ASSXJ /D/ 04DIAMETER,HOLE/STUD,MOUNTING MOUNTING HOLE/STUD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE OR STUD,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ASSYD /D/ 07INCLINOMETER INCLINOMETER AN INDICATION OF WHETHER OR NOT AN INCLINOMETER IS INCLUDED. SELECT REPLY CODE 10AA49 ASSZA /D/ 12QUANTITY,INDEX,REFERENCE REFERENCE INDEX QUANTITY THE NUMBER OF REFERENCE INDEXES INCLUDED. 1A MODE REPLY 0 ASTAD /D/ 01COLOR,INDEX,REFERENCE REFERENCE INDEX COLOR THE HUE OR TINT OF THE REFERENCE INDEX. SELECT REPLY CODE 10AD06 ASTBD /D/ 07PROVISION,SETTING,REFERENCE INDEX REFERENCE INDEX SETTING PROVISION AN INDICATION OF WHETHER OR NOT THE REFERENCE INDEX INCLUDES A PROVISION FOR SETTING. SELECT REPLY CODE 10AA49 ASTCA /D/ 12QUANTITY,MARKING/SYMBOL MARKING/SYMBOL QUANTITY THE NUMBER OF MARKINGS AND/OR SYMBOLS ON THE ITEM. 1A MODE REPLY 0 ASTDG /D/ 19MARKING/SYMBOL MARKING/SYMBOL AN INDICATION OF THE MARKING/S/ AND/OR SYMBOL/S/ ON THE ITEM. FULL TEXT WRITE-IN 0 ASTED /D/ 19FINISH,MARKING/SYMBOL MARKING/SYMBOL FINISH AN INDICATION OF THE FINISH ON THE MARKING AND/OR SYMBOL. SELECT REPLY CODE 10AB54 ASTFD /D/ 01COLOR,MARKING/SYMBOL MARKING/SYMBOL COLOR THE HUE OR TINT OF THE MARKING AND/OR SYMBOL. SELECT REPLY CODE 10AD06 ASTGD /D/ 07ADAPTER,VOLTAGE,RESISTOR TYPE RESISTOR TYPE VOLTAGE ADAPTER AN INDICATION OF WHETHER OR NOT A RESISTOR TYPE VOLTAGE ADAPTER IS PROVIDED. SELECT REPLY CODE 10AB22 ASTHB /D/ 10RESISTANCE IN OHMS,ADAPTER,VOLTAGE VOLTAGE ADAPTER RESISTANCE IN OHMS THE OPPOSITION TO THE FLOW OF CURRENT THROUGH THE VOLTAGE ADAPTER,EXPRESSED IN OHMS. 1B MODE REPLY 0 ASTJD /D/ 08LOCATION,FEATURE,STABILIZATION STABILIZATION FEATURE LOCATION INDICATES THE LOCATION OF THE STABILIZATION FEATURE. SELECT REPLY CODE 10AJ91 ASTKD /D/ 07ILLUMINATION,DIAL DIAL ILLUMINATION AN INDICATION OF WHETHER OR NOT DIAL ILLUMINATION SELECT REPLY CODE 10AB22 ASTLD /D/ 08LOCATION,SOURCE,LIGHT LIGHT SOURCE LOCATION INDICATES THE LOCATION OF THE LIGHT SOURCE ON THE ITEM. SELECT REPLY CODE 10AJ91 ASTMD /D/ 07COUNTER,TOTALIZING TOTALIZING COUNTER AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES A TOTALIZING COUNTER. SELECT REPLY CODE 10AA49 ASTNF /D/T10RANGE,RECORDING RECORDING RANGE THE SMALLEST AND LARGEST VALUES THE ITEM WILL REGISTER. 1F MODE REPLY 0 ASTPA 12QUANTITY,TRANSMITTER TRANSMITTER QUANTITY THE NUMBER OF TRANSMITTERS INCLUDED. 1A MODE REPLY 0 ASTQD /D/ 11METHOD,ACTUATION,TRANSMITTER TRANSMITTER ACTUATION METHOD THE MEANS BY WHICH THE TRANSMITTER IS ACTUATED. SELECT REPLY CODE 10AC58 ASTRD /D/ 07FEATURE,CALIBRATION,MULTIPLE MULTIPLE CALIBRATION FEATURE AN INDICATION OF WHETHER OR NOT A MULTIPLE CALIBRATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ASTSD /D/ 07LINE,SAMPLING SAMPLING LINE AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES A SAMPLING LINE(S). SELECT REPLY CODE 10AA49 ASTTD /D/ 07VALVE,DILUTION DILUTION VALVE AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES A DILUTION VALVE. SELECT REPLY CODE 10AA49 ASTWG 19MARKING,SCALE SCALE MARKING AN INDICATION OF THE MARKING(S) ON THE SCALE. FULL TEXT WRITE-IN 0 ASTXJ /D/ 04LENGTH,FIBER FIBER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FIBER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ASTYD 19USAGE,TIME TIME USAGE AN INDICATION OF THE TIME THE ITEM IS DESIGNED TO BE USED. SELECT REPLY CODE 10AL99 ASTZD 19SPEED,FLIGHT FLIGHT SPEED THE SPEED OF FLIGHT FOR WHICH THE ITEM IS RATED. SELECT REPLY CODE 10AG48 ASWAD 19SPECIES,WOOD WOOD SPECIES THE BOTANICAL VARIETY TO WHICH THE WOOD BELONGS. SELECT REPLY CODE 10AM00 ASWBD /D/ 03DESIGNATOR,GRADE,WOOD WOOD GRADE DESIGNATOR THE DESIGNATION BY WHICH THE GRADE,OR QUALITY,OF THE WOOD IS KNOWN. SELECT REPLY CODE 10AM01 ASWCD 19FORM,MATERIAL MATERIAL FORM THE FORM OR STRUCTURE OF THE MATERIAL OF WHICH AN ITEM IS FABRICATED. SELECT REPLY CODE 10AL59 ASWDD /D/ 09MATERIAL,BOWSTRING BOWSTRING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BOWSTRING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ASWED /D/ 17SURFACE TREATMENT,SHAFT SHAFT SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A SHAFT SURFACE. SELECT REPLY CODE 10AD09 ASWFD /D/ 17SURFACE TREATMENT,HEAD HEAD SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A HEAD SURFACE. SELECT REPLY CODE 10AD09 ASWGD 18TYPE,CLUB CLUB TYPE INDICATES THE TYPE OF CLUB. SELECT REPLY CODE 10AM02 ASWHB 10PULL RATING IN POUNDS PULL RATING IN POUNDS THE FORCE OR EFFORT REQUIRED,EXPRESSED IN POUNDS. 1B MODE REPLY 0 ASWJD /D/ 07SERVE,CENTER CENTER SERVE AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A CENTER SERVE. SELECT REPLY CODE 10AB22 ASWKD 02DESIGN,END END DESIGN THE PARTICULAR DESIGN OF THE END(S) OF THE ITEM. SELECT REPLY CODE 10AK54 ASWLD 14SHAPE,SHANK SHANK SHAPE THE PHYSICAL CONFIGURATION OF THE SHANK. SELECT REPLY CODE 10AD07 ASWMA 12QUANTITY,NEEDLE NEEDLE QUANTITY THE NUMBER OF NEEDLES PROVIDED. 1A MODE REPLY 0 ASWNG 03DESIGNATION,SIZE SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. FULL TEXT WRITE-IN 0 ASWPD /D/ 18TYPE,STRAND,RUBBER RUBBER STRAND TYPE INDICATES THE TYPE OF RUBBER STRAND PROVIDED. SELECT REPLY CODE 10AF12 ASWQA /D/ 12QUANTITY,LAYER,BRAID BRAID LAYER QUANTITY THE NUMBER OF BRAID LAYERS PROVIDED. 1A MODE REPLY 0 ASWRG /D/ 09MATERIAL,LAYER,BRAID BRAID LAYER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BRAID LAYER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. FULL TEXT WRITE-IN 0 ASWSA /D/ 12QUANTITY,THREAD/STRAND,BRAID BRAID THREAD/STRAND QUANTITY THE NUMBER OF THREAD/STRANDS THAT COMPRISE THE BRAID. 1A MODE REPLY 0 ASWTJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CONNECTION,INTAKE INTAKE CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE INTAKE CONNECTION. 1D AND 1A MODE REPLY12AH06 ASWWD /D/ 08LOCATION,TIP TIP LOCATION INDICATES THE LOCATION OF THE TIP(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 ASWXG /D/ 10LOAD,ELONGATION ELONGATION LOAD AN INDICATION OF THE LOAD REQUIRED TO PRODUCE A GIVEN AMOUNT OF ELONGATION. FULL TEXT WRITE-IN 0 ASWYD /D/ 07DATE MANUFACTURED DATE MANUFACTURED AN INDICATION OF WHETHER OR NOT A DATE OF MANUFACTURE IS INCLUDED. SELECT REPLY CODE 10AA49 ASWZD /D/ 07STOP,SECURITY SECURITY STOP AN INDICATION OF WHETHER OR NOT A SECURITY STOP IS INCLUDED. SELECT REPLY CODE 10AA49 ASXAJ /D/ 04LENGTH AND HOLDER TYPE,LINE LINE LENGTH AND HOLDER TYPE AN INDICATION OF THE LENGTH OF LINE AND THE TYPE OF HOLDER PROVIDED. 2D AND 1B MODE REPLY21AA052AG46 ASXBA 12QUANTITY,HOLDER,CONNECTED CONNECTED HOLDER QUANTITY THE NUMBER OF CONNECTED HOLDERS. 1A MODE REPLY 0 ASXCD 19GAME FOR WHICH DESIGNED GAME FOR WHICH DESIGNED THE PARTICULAR GAME FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AM03 ASXDD /D/ 09MATERIAL,PAD,FACE FACE PAD MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FACE PAD IS FABRICATED. SELECT REPLY CODE 10AD09 ASXED /D/ 07PAD,FACE,REPLACEABLE REPLACEABLE FACE PAD AN INDICATION OF WHETHER OR NOT REPLACEABLE FACE PADS ARE PROVIDED. SELECT REPLY CODE 10AB22 ASXFD /D/ 07GUARD,EAR EAR GUARD AN INDICATION OF WHETHER OR NOT EAR GUARDS ARE PROVIDED. SELECT REPLY CODE 10AB22 ASXGD /D/ 07HOLE,LOCKWIRE,DRILLED DRILLED LOCKWIRE HOLE AN INDICATION OF WHETHER OR NOT A DRILLED LOCKWIRE HOLE IS INCLUDED. SELECT REPLY CODE 10AA49 ASXHJ 10VOLTAGE RATING IN VOLTS VOLTAGE RATING IN VOLTS THE VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN VOLTS. 2D AND 1B MODE REPLY21AB621AC20 ASXJJ 10HARDNESS RATING AND LOCATION,METALLIC METALLIC HARDNESS RATING AND LOCATION A NUMERIC VALUE,USED IN CONJUNCTION WITH A HARDNESS RATING SCALE,DESIGNATING THE METALLIC HARDNESS RATING AND ITS LOCATION. 3D AND 1B MODE REPLY32AC261AC203AJ91 ASXKA 12QUANTITY,HOLE HOLE QUANTITY THE NUMBER OF HOLES PROVIDED. 1A MODE REPLY 0 ASXLA 04DIAMETER IN LINES,HEAD HEAD DIAMETER IN LINES THE DIAMETER OF THE BUTTON HEAD,EXPRESSED IN LINES. 1A MODE REPLY 0 ASXMJ 04DISTANCE BETWEEN FIRST AND SECOND TERMINALS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FIRST AND SECOND TERMINALS NONE. 2D AND 1B MODE REPLY21AA051AC20 ASXNJ 04DISTANCE BETWEEN SECOND AND THIRD TERMINALS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SECOND AND THIRD TERMINALS NONE. 2D AND 1B MODE REPLY21AA051AC20 ASXPJ 04DISTANCE BETWEEN THIRD AND FOURTH TERMINALS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN THIRD AND FOURTH TERMINALS NONE. 2D AND 1B MODE REPLY21AA051AC20 ASXQG /D/ 10RANGE,GRADUATION GRADUATION RANGE AN INDICATION OF THE GRADUATION RANGE OF THE ITEM. FULL TEXT WRITE-IN 0 ASXRH /D/ 19FINISH/COLOR AND LOCATION,SURFACE,POINTER POINTER SURFACE FINISH/COLOR AND LOCATION AN INDICATION OF THE SURFACE FINISH AND ITS COLOR ON THE POINTER AND THE LOCATION. 3D MODE REPLY 31AB546AD063AJ91 ASXSH /D/ 01COLOR AND LOCATION,POINTER POINTER COLOR AND LOCATION THE HUE OR TINT OF THE POINTER AND THE LOCATION. 2D MODE REPLY 26AD063AJ91 ASXTG /D/ 10RANGE,OPERATING OPERATING RANGE THE MINIMUM AND MAXIMUM OPERATING LIMITS OF THE ITEM. FULL TEXT WRITE-IN 0 ASXWB /D/ 10RPM EQUIVALENT TO 100 PCT RPM EQUIVALENT TO 100 PCT THE NUMBER OF REVOLUTIONS PER MINUTE EQUAL TO 100 PERCENT. 1B MODE REPLY 0 ASXXD /D/ 07SYNCHROSCOPE,INTEGRAL INTEGRAL SYNCHROSCOPE AN INDICATION OF WHETHER OR NOT AN INTERGRAL SYNCHROSCOPE IS PROVIDED. SELECT REPLY CODE 10AB22 ASXYG /D/ 19NAME,COUNTER,TOTALIZING TOTALIZING COUNTER NAME THE NOMENCLATURE BY WHICH THE TOTALIZING COUNTER IS IDENTIFIED. FULL TEXT WRITE-IN 0 ASXZF /D/T10RATIO,SPEED,GENERATING TRANSMITTER-INDICATION GENERATING TRANSMITTER-INDICATION SPEED RATIO THE RELATIVE VALUES OF THE SPEEDS OF THE GENERATING TRANSMITTER AND THE INDICATOR. 1F MODE REPLY 0 ASYAJ /D/ 10RESISTANCE IN OHMS,CIRCUIT,EXTERNAL EXTERNAL CIRCUIT RESISTANCE IN OHMS THE OPPOSITION TO THE FLOW OF ELECTRICAL CURRENT OFFERED BY THE EXTERNAL CIRCUIT,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 ASYBD /D/ 09MATERIAL,THERMOCOUPLE THERMOCOUPLE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE THERMOCOUPLE IS FABRICATED. SELECT REPLY CODE 10AD09 ASYCB 10LOSS AT MINIMUM ATTENUATION IN MAXIMUM DECIBELS,INSERTION INSERTION LOSS AT MINIMUM ATTENUATION IN MAXIMUM DECIBELS THE MATHEMATICAL RELATIONSHIP OF POWER AVAILABLE AT THE LOAD BEFORE AND AFTER ADDITION OF THE ITEM TO THE CIRCUIT,SET TO ITS LOWEST VALUE OF ATTENUATION,EXPRESSED IN MAXIMUM DECIBELS. 1B MODE REPLY 0 ASYDF T10RANGE IN DECIBELS,ATTENUATION,OVERALL OVERALL ATTENUATION RANGE IN DECIBELS THE OVERALL LIMITS OF DECREASE OF THE AMPLITUDE RATIO OF A SIGNAL BETWEEN THE INPUT AND OUTPUT OF THE ITEM,EXPRESSED IN DECIBELS. 1F MODE REPLY 0 ASYEJ 10FREQUENCY,REFERENCE,ATTENUATION ACCURACY ATTENUATION ACCURACY REFERENCE FREQUENCY THE FREQUENCY AT WHICH THE ATTENUATION ACCURACY WAS MEASURED. 1D AND 1B MODE REPLY11AC32 ASYFD 11METHOD,VARIATION,ATTENUATION ATTENUATION VARIATION METHOD THE MEANS BY WHICH THE ATTENUATION CAN BE VARIED FROM THE MINIMUM TO THE MAXIMUM SETTING. SELECT REPLY CODE 10AD63 ASYGA 12QUANTITY,POSITION,STEP STEP POSITION QUANTITY THE NUMBER OF INTERVALS AT WHICH THE ITEM CAN BE SET. 1A MODE REPLY 0 ASYHB 10ATTENUATION PER STEP IN DECIBELS ATTENUATION PER STEP IN DECIBELS THE AMOUNT OF ATTENUATION BETWEEN ADJACENT STEPS,EXPRESSED IN DECIBELS. 1B MODE REPLY 0 ASYJD /D/ 07SCALE,VENIER VENIER SCALE AN INDICATION OF WHETHER OR NOT A VERNIER SCALE IS INCLUDED. SELECT REPLY CODE 10AA49 ASYKA 12QUANTITY,DIVISION,VERNIER SCALE VERNIER SCALE DIVISION QUANTITY THE NUMBER OF INCREMENTS ON A SMALLER AUXILIARY SCALE WHICH PROVIDES FRACTIONAL READINGS OF THE VERNIER SCALE MAIN DIVISIONS. 1A MODE REPLY 0 ASYLA 19CODE,MANUFACTURER,WAVEGUIDE FLANGE WAVEGUIDE FLANGE MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE WAVEGUIDE FLANGE. 1A MODE REPLY 0 ASYMA /D/ 19NUMBER,IDENTIFYING,WAVEGUIDE FLANGE MANUFACTURER WAVEGUIDE FLANGE MANUFACTURER IDENTIFYING NUMBER THE IDENTIFYING NUMBER ASSIGNED BY THE MANUFACTURER WHO CONTROLS THE WAVEGUIDE FLANGE. 1A MODE REPLY 0 ASYNF T10ACCURACY IN DECIBELS,ATTENUATION ATTENUATION ACCURACY IN DECIBELS THE LIMITS OF PERMISSIBLE VARIATION IN THE ATTENUATION ACCURACY FROM THE NOMINAL VALUE AT A SPECIFIED FREQUENCY RATING OR RANGE,EXPRESSED IN DECIBELS. 1F MODE REPLY 0 ASYPA 03DESIGNATION,WAVEGUIDE WAVEGUIDE DESIGNATION THE ALPHABETIC AND/OR NUMERIC CHARACTERS WHICH IDENTIFY THE WAVEGUIDE TYPE. 1A MODE REPLY 0 ASYQJ 04DISTANCE FROM TAPER TO END DISTANCE FROM TAPER TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 ASYRJ 04DISTANCE FROM HUB END TO FLANGE END DISTANCE FROM HUB END TO FLANGE END NONE. 2D AND 1B MODE REPLY21AA051AC20 ASYSD 18TYPE,TAKEUP TAKEUP TYPE INDICATES THE TYPE OF TAKEUP. SELECT REPLY CODE 10AL48 ASYTG 10AMOUNT,TAKEUP TAKEUP AMOUNT THE AMOUNT OF TAKEUP THE ITEM IS DESIGNED TO ACHIEVE. FULL TEXT WRITE-IN 0 ASYWD 18TYPE ACCOMMODATED,SEAL SEAL TYPE ACCOMMODATED INDICATES THE TYPE OF SEAL THE ITEM IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AG89 ASYXD 18TYPE,CRIMP CRIMP TYPE INDICATES THE TYPE OF CRIMP ON THE ITEM. SELECT REPLY CODE 10AL76 ASYYD 18TYPE,JAW JAW TYPE INDICATES THE TYPE OF JAW FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AK42 ASYZD /D/ 07MAGAZINE,SEAL SEAL MAGAZINE AN INDICATION OF WHETHER OR NOT A SEAL MAGAZINE IS INCLUDED. SELECT REPLY CODE 10AA49 ASZAD /D/ 07DEVICE,CUTOFF CUTOFF DEVICE AN INDICATION OF WHETHER OR NOT A CUTOFF DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 ASZBJ 04THICKNESS,STRAP STRAP THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE STRAP,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ASZCD 11METHOD,CONTROL,CROWD CROWD CONTROL METHOD THE MEANS BY WHICH THE CROWD IS CONTROLLED. SELECT REPLY CODE 10AF37 ASZDJ 10LOAD RATING LOAD RATING THE RATED LOAD THE ITEM IS DESIGNED TO ACCOMMODATE. 2D AND 1B MODE REPLY22AG671AC20 ASZEJ 04LENGTH AT WHICH RATED,BOOM BOOM LENGTH AT WHICH RATED THE ACTUAL MEASUREMENT OF THE LONGEST DIMENSION OF THE BOOM AT WHICH THE LOAD RATING IS TAKEN,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ASZFJ 04RADIUS AT WHICH RATED,BOOM BOOM RADIUS AT WHICH RATED THE ACTUAL RADIUS OF SWING AT WHICH THE BOOM IS RATED. 2D AND 1B MODE REPLY21AA051AC20 ASZGJ A18TYPE AND QUANTITY,PROTRUSION PROTRUSION TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF PROTRUSIONS. 1D AND 1A MODE REPLY13AJ54 ASZHD 02DESIGN,BOOM BOOM DESIGN THE DESIGN OF THE BOOM. SELECT REPLY CODE 10AH47 ASZJD /D/ 07ACCOMMODATION,EXTENSION,MIDDLE BOOM MIDDLE BOOM EXTENSION ACCOMMODATION AN INDICATION OF WHETHER OR NOT AN ACCOMMODATION FOR A MIDDLE BOOM EXTENSION IS INCLUDED. USE MRC CBBL WITH CODED REPLY CODE GLE SELECT REPLY CODE 10AA49 ASZKD 18TYPE,COUPLING,END END COUPLING TYPE INDICATES THE TYPE OF END COUPLING PROVIDED. SELECT REPLY CODE 10AH98 ASZLB 10ATTENUATION IN DECIBELS,SENSITIVITY,FREQUENCY FREQUENCY SENSITIVITY ATTENUATION IN DECIBELS THE TOTAL VARIATION IN ATTENUATION VALUE ACROSS THE OPERATING FREQUENCY RANGE,EXPRESSED IN DECIBELS. 1B MODE REPLY 0 ASZMB 10ATTENUATION IN DECIBELS,SENSITIVITY,TEMPERATURE TEMPERATURE SENSITIVITY ATTENUATION IN DECIBELS THE SPECIFIED VARIATION OF ATTENUATION CAUSED BY A CHANGE OF TEMPERATURE,EXPRESSED IN DECIBELS. 1B MODE REPLY 0 ASZNH /D/ 18TYPE PER FUNCTION,CONNECTION CONNECTION TYPE PER FUNCTION INDICATES THE TYPE OF CONNECTION PER FUNCTION. 2D MODE REPLY 23AJ681AC00 ASZPD 18TYPE,CAMERA CAMERA TYPE INDICATES THE TYPE OF CAMERA. SELECT REPLY CODE 10AM04 ASZQJ /D/ 04ANGLE IN DEG,LENS FIELD LENS FIELD ANGLE IN DEG THE LENS FIELD ANGLE,EXPRESSED IN DEGREES. 2D AND 1B MODE REPLY21AC202AM05 ASZRD 10RATIO,REDUCTION,MAXIMUM MAXIMUM REDUCTION RATIO THE MAXIMUM RATIO BY WHICH THE ITEM MAY BE REDUCED. SELECT REPLY CODE 10AM06 ASZSD 19RATIO,ENLARGEMENT,MAXIMUM MAXIMUM ENLARGEMENT RATIO THE MAXIMUM RATIO BY WHICH THE ITEM MAY BE ENLARGED. SELECT REPLY CODE 10AM06 ASZTF T10RANGE,SETTING,LENS APERTURE LENS APERTURE SETTING RANGE THE MINIMUM AND MAXIMUM SETTING LIMITS OF THE LENS APERTURE. 1F MODE REPLY 0 ASZWH 18TYPE,SHUTTER SHUTTER TYPE INDICATES THE TYPE OF SHUTTER. 2D MODE REPLY 22AL362AM07 ASZXJ 10SPEED IN SECONDS,EXPOSURE,SHUTTER SHUTTER EXPOSURE SPEED IN SECONDS THE LENGTH OF TIME THE SHUTTER REMAINS OPEN,EXPRESSED IN SECONDS. 2D AND 1B MODE REPLY21AC202AL36 ASZYB 04DEGREE OF SHUTTER OPENING,MAXIMUM MAXIMUM DEGREE OF SHUTTER OPENING THE MAXIMUM DEGREES OF OPENING FOR WHICH THE SHUTTER DISC IS DESIGNED. 1B MODE REPLY 0 ASZZD 18TYPE,MOUNTING,CAMERA CAMERA MOUNTING TYPE INDICATES THE TYPE OF MOUNT UTILIZED TO SUPPORT THE CAMERA. SELECT REPLY CODE 10AA78 ATAAD /D/ 07RELEASE,FRAME,SINGLE SINGLE FRAME RELEASE AN INDICATION OF WHETHER OR NOT A SINGLE FRAME RELEASE IS INCLUDED. SELECT REPLY CODE 10AA49 ATABD 18TYPE,ACCOMMODATION,FILM FILM ACCOMMODATION TYPE INDICATES THE TYPE OF FILM ACCOMMODATION PROVIDED. SELECT REPLY CODE 10AG37 ATACD /D/ 11METHOD,ATTACHMENT,STAPLE STAPLE ATTACHMENT METHOD THE MEANS BY WHICH THE STAPLE IS ATTACHED. SELECT REPLY CODE 10AB47 ATADJ /D/ 19CHARACTERISTIC AND LENGTH,FOCAL,LENS LENS FOCAL CHARACTERISTIC AND LENGTH AN INDICATION OF THE CHARACTERISTIC OF THE DISTANCE FROM THE CENTER OF A LENS TO THE FOCAL PLANE. 3D AND 1B MODE REPLY31AA051AC202AL36 ATAFD 18TYPE,CONTROL,MANUAL EXPOSURE MANUAL EXPOSURE CONTROL TYPE INDICATES THE TYPE OF CONTROL THAT OPERATES THE EXPOSURE MANUALLY. SELECT REPLY CODE 10AL37 ATAGG /D/ 10PERCENTAGE,MATERIAL,BASIC BASIC MATERIAL PERCENTAGE THE PERCENTAGE AND TYPES OF MATERIALS USED IN THE ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. FULL TEXT WRITE-IN 0 ATAHJ 10RATE PER SECOND,FRAME FRAME RATE PER SECOND THE NUMBER OF FRAMES FOR WHICH THE ITEM IS RATED PER SECOND. 1D AND 1B MODE REPLY12AL36 ATAJA 04SIZE FOR WHICH DESIGNED,FILM FILM SIZE FOR WHICH DESIGNED THE SIZE OF THE FILM FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 ATAKJ 04WIDTH,FILM FILM WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FILM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ATALA 12QUANTITY ACCOMMODATED,EXPOSURE EXPOSURE QUANTITY ACCOMMODATED THE NUMBER OF EXPOSURES THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 ATAMD 11METHOD,FOCUS FOCUS METHOD THE MEANS BY WHICH THE ITEM IS FOCUSED. SELECT REPLY CODE 10AC58 ATAND 07PLATED PLATED AN INDICATION OF WHETHER OR NOT THE ITEM IS PLATED. SELECT REPLY CODE 10AM08 ATAPD 18TYPE,VIEWFINDER VIEWFINDER TYPE INDICATES THE TYPE OF VIEWFINDER PROVIDED. SELECT REPLY CODE 10AM04 ATAQD /D/ 07FEATURE,AUDIO AUDIO FEATURE AN INDICATION OF WHETHER OR NOT AN AUDIO FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ATARD 18TYPE,RECORDING RECORDING TYPE INDICATES THE TYPE OF RECORDING PROVIDED. SELECT REPLY CODE 10AH84 ATASD 11METHOD,MOUNTING,LENS LENS MOUNTING METHOD THE MEANS BY WHICH THE LENS IS MOUNTED TO AN ITEM. SELECT REPLY CODE 10AB89 ATATD /D/ 07GRADUATION FOR ABANDON-SHIP EQUIPMENT,RATIONING,WATER WATER RATIONING GRADUATION FOR ABANDON-SHIP EQUIPMENT AN INDICATION OF WHETHER OR NOT GRADUATIONS FOR RATIONING WATER IN ABANDON-SHIP EQUIPMENT ARE PROVIDED. PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB22 ATAWJ 04LENGTH,FILM FILM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FILM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ATAXD /D/ 07LEADER LEADER AN INDICATION OF WHETHER OR NOT A LEADER IS INCLUDED. SELECT REPLY CODE 10AA49 ATAYD /D/ 07TRAILER TRAILER AN INDICATION OF WHETHER OR NOT A TRAILER IS INCLUDED. SELECT REPLY CODE 10AA49 ATAZD /D/ 07FEATURE,PLEATED PLEATED FEATURE AN INDICATION OF WHETHER OR NOT A PLEATED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ATBAJ /D/ 04THICKNESS,BASE,FILM FILM BASE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE FILM BASE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ATBBJ 04WIDTH,NEGATIVE NEGATIVE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE NEGATIVE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ATBCJ 04LENGTH,NEGATIVE NEGATIVE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE NEGATIVE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ATBDD 11METHOD,ADVANCE,FILM FILM ADVANCE METHOD THE MEANS BY WHICH THE FILM IS ADVANCED. SELECT REPLY CODE 10AC58 ATBEJ 04WIDTH,TOP TOP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TOP,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ATBFJ /D/ 04DIAMETER,BOOM,CARGO CARGO BOOM DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CARGO BOOM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ATBGD /D/ 07ADJUSTABILITY,SHEAVE,CARGO BOOM CARGO BOOM SHEAVE ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE CARGO BOOM SHEAVE IS ADJUSTABLE. SELECT REPLY CODE 10AB00 ATBHA 12QUANTITY,ROLLER ROLLER QUANTITY THE NUMBER OF ROLLERS PROVIDED. 1A MODE REPLY 0 ATBJD /D/ 09MATERIAL,ROLLER ROLLER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ROLLER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH ISAC FOR ROLLER IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 ATBKD 19POSITION,MOUNTING,ROLLER ROLLER MOUNTING POSITION THE MOUNTING POSITION OF THE ROLLER. SELECT REPLY CODE 10AC60 ATBLD 19POSITION,MOUNTING,SHEAVE SHEAVE MOUNTING POSITION AN INDICATION OF THE MOUNTING POSITION OF THE SHEAVE. SELECT REPLY CODE 10AC60 ATBMD /D/ 07FEATURE,PENDULUM PENDULUM FEATURE AN INDICATION OF WHETHER OR NOT A PENDULUM FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ATBND /D/ 07FEATURE,GUIDE GUIDE FEATURE AN INDICATION OF WHETHER OR NOT A GUIDE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ATBPJ 04DISTANCE BETWEEN GUIDES DISTANCE BETWEEN GUIDES THE DISTANCE BETWEEN GUIDES ON THE ITEM. 1D AND 1B MODE REPLY11AA05 ATBQJ 04WIDTH,GUIDE GUIDE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE GUIDE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 ATBRG /D/ 19CHARACTERISTIC,SECTION SECTION CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC/S/ OF THE SECTION/S/. FULL TEXT WRITE-IN 0 ATBSD /D/ 18TYPE,MATERIAL MATERIAL TYPE INDICATES THE TYPE OF MATERIAL USED ON THE ITEM. SELECT REPLY CODE 10AD93 ATBTD 08LOCATION,FUZE FUZE LOCATION INDICATES THE LOCATION OF THE FUZE ON THE ITEM. SELECT REPLY CODE 10AJ91 ATBWD /D/ 07ACTIVATOR ACTIVATOR AN INDICATION OF WHETHER OR NOT AN ACTIVATOR IS INCLUDED. SELECT REPLY CODE 10AA49 ATBXD 19CONTENT,ACTIVATOR ACTIVATOR CONTENT AN INDICATION OF THE CONTENT OF THE ACTIVATOR. SELECT REPLY CODE 10AL22 ATBYA 19NUMBER,MODEL,ACTIVATOR ACTIVATOR MODEL NUMBER A COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE ACTIVATOR. 1A MODE REPLY 0 ATBZA 03DESIGNATOR,ASSEMBLY,OPERATIONAL OPERATIONAL ASSEMBLY DESIGNATOR A DESIGNATION INDICATING THE OPERATIONAL ASSEMBLY OF THE ITEM. 1A MODE REPLY 0 ATCAA 19CODE,CONFIGURATION CONFIGURATION CODE THE CODE INDICATING THE LEVEL OF ASSEMBLY OF THE ITEM. 1A MODE REPLY 0 ATCBD /D/ 18TYPE FOR WHICH DESIGNED,GRENADE GRENADE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF GRENADE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 ATCCA 12QUANTITY,CLIP,LAUNCHING LAUNCHING CLIP QUANTITY THE NUMBER OF LAUNCHING CLIPS INCLUDED. 1A MODE REPLY 0 ATCDA 12QUANTITY,POSITIONING,LAUNCHER CLIP LAUNCHER CLIP POSITIONING QUANTITY THE NUMBER OF LAUNCHER POSITIONING CLIPS ON THE ITEM. 1A MODE REPLY 0 ATCED 18TYPE,RETAINER,TOOL TOOL RETAINER TYPE INDICATES THE TYPE OF TOOL RETAINER PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AJ68 ATCFD /D/ 07FEATURE FOR SINKER DRILL OPERATION,CONVERSION CONVERSION FEATURE FOR SINKER DRILL OPERATION AN INDICATION OF WHETHER OR NOT A CONVERSION FEATURE FOR SINKER DRILL OPERATION IS INCLUDED. SELECT REPLY CODE 10AA49 ATCGJ 04LENGTH,OVERALL,SHANK SHANK OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE SHANK. 2D AND 1B MODE REPLY21AA051AC20 ATCHJ 04DIAMETER,RETAINER RETAINER DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 ATCJJ /D/ 04WIDTH ACROSS FLATS,RETAINER RETAINER WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 ATCKJ /D/ 04DISTANCE FROM RETAINER GROOVE CENTER TO FLANGE DISTANCE FROM RETAINER GROOVE CENTER TO FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 ATCLJ /D/ 04DISTANCE FROM SHANK END TO RETAINER GROOVE CENTER DISTANCE FROM SHANK END TO RETAINER GROOVE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 ATCMD 18TYPE,SHANK,ROD ROD SHANK TYPE INDICATES THE TYPE OF ROD SHANK PROVIDED. SELECT REPLY CODE 10AM11 ATCND /D/ 09MATERIAL,TIRE TIRE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TIRE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ATCPJ 04LENGTH,FEED FEED LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FEED. 2D AND 1B MODE REPLY21AA051AC20 ATCQJ 04DIAMETER,HOLE,DRILL CAPACITY DRILL CAPACITY HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOLE THE ITEM HAS THE CAPACITY TO DRILL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ATCRJ 04DEPTH,HOLE,DRILL CAPACITY DRILL CAPACITY HOLE DEPTH THE MEASUREMENT BETWEEN SPECIFIED POINTS OF THE HOLE THE ITEM HAS THE CAPACITY TO DRILL,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 ATCSD 19SOURCE,POWER,DRILL DRILL POWER SOURCE THE SOURCE OF POWER WHICH DRIVES THE DRILL. SELECT REPLY CODE 10AG27 ATCTD 19CONSTRUCTION,MAST MAST CONSTRUCTION AN INDICATION OF THE STRUCTURAL FORM OF THE MAST. SELECT REPLY CODE 10AL59 ATCWD /D/ 07FEATURE,MAST,POWER RAISED POWER RAISED MAST FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES A FEATURE FOR THE MAST TO BE RAISED BY POWER. SELECT REPLY CODE 10AA49 ATCXJ 04HEIGHT,MAXIMUM,MAST MAST MAXIMUM HEIGHT THE MAXIMUM MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE MAST,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 ATCYA 12QUANTITY,DRUM,HOIST HOIST DRUM QUANTITY THE NUMBER OF HOIST DRUMS PROVIDED. 1A MODE REPLY 0 ATCZD 18TYPE,ROTARY ROTARY TYPE INDICATES THE TYPE OF ROTARY PROVIDED. SELECT REPLY CODE 10AM16 ATDAD 18TYPE,PUMP,LIQUID CIRCULATING LIQUID CIRCULATING PUMP TYPE INDICATES THE TYPE OF PUMP PROVIDED FOR CIRCULATING LIQUID. SELECT REPLY CODE 10AA80 ATDBG /D/ 10CAPACITY,PUMP PUMP CAPACITY THE RATED CAPACITY OF THE PUMP. FULL TEXT WRITE-IN 0 ATDCJ 10VOLTAGE RATING,MOTOR,DRIVE DRIVE MOTOR VOLTAGE RATING THE TYPE AND AMOUNT OF VOLTAGE FOR WHICH THE DRIVE MOTOR IS DESIGNED. 1D AND 1B MODE REPLY12AG13 ATDDJ 04THICKNESS,MINIMUM,MATERIAL MATERIAL MINIMUM THICKNESS THE MINIMUM MEASUREMENT OF THE SMALLEST DIMENSION OF THE MATERIAL,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 ATDEB 10FREQUENCY IN HERTZ,CURRENT,DRIVE MOTOR DRIVE MOTOR CURRENT FREQUENCY IN HERTZ THE CYCLES PER SECOND (HERTZ) OF ALTERNATING CURRENT FOR WHICH THE DRIVE MOTOR IS DESIGNED. 1B MODE REPLY 0 ATDFD /D/ 07FEATURE,PARAFFINED PARAFFINED FEATURE AN INDICATION OF WHETHER OR NOT A PARAFFINED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ATDGD 19PHASE,MOTOR,DRIVE DRIVE MOTOR PHASE THE NUMBER OF ALTERNATING CURRENT PHASE/S/ FOR WHICH THE DRIVE MOTOR IS DESIGNED. SELECT REPLY CODE 10AD02 ATDHD /D/ 07STRAP,CARRYING CARRYING STRAP AN INDICATION OF WHETHER OR NOT A CARRYING STRAP IS INCLUDED. SELECT REPLY CODE 10AA49 ATDJD /D/ 07SUITABILITY,LIQUID/SOLID,HOT HOT LIQUID/SOLID SUITABILITY AN INDICATION OF WHETHER OR NOT THE ITEM IS SUITABLE FOR HOT LIQUIDS AND SOLIDS. SELECT REPLY CODE 10AM09 ATDKD 18TYPE,HOLDER,FILM FILM HOLDER TYPE INDICATES THE TYPE OF FILM HOLDER PROVIDED. SELECT REPLY CODE 10AF72 ATDLD 18TYPE,BOARD,COPY COPY BOARD TYPE INDICATES THE TYPE OF COPY BOARD PROVIDED. SELECT REPLY CODE 10AF72 ATDMD /D/ 07SLOT,STRAW STRAW SLOT AN INDICATION OF WHETHER OR NOT A STRAW SLOT IS INCLUDED. SELECT REPLY CODE 10AA49 ATDND /D/ 07WINDOW WINDOW AN INDICATION OF WHETHER OR NOT A WINDOW IS INCLUDED. PLEASE USE MRC ABFF OR TMQY IN PLACE OF THIS CANCLED MRC. SELECT REPLY CODE 10AA49 ATDPJ 04WIDTH,MAXIMUM,COPY BOARD COPY BOARD MAXIMUM WIDTH THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE COPY BOARD,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 ATDQJ 04LENGTH,MAXIMUM,BOARD,COPY COPY BOARD MAXIMUM LENGTH THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF THE COPY BOARD,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 ATDRJ 10VOLTAGE RATING,MOTOR,VACUUM PUMP VACUUM PUMP MOTOR VOLTAGE RATING THE TYPE AND AMOUNT OF VOLTAGE FOR WHICH THE VACUUM PUMP MOTOR IS DESIGNED. 1D AND 1B MODE REPLY12AG13 ATDSB 10CAPACITY FOR WHICH DESIGNED IN OUNCES,CUP CUP CAPACITY FOR WHICH DESIGNED IN OUNCES THE CAPACITY OF THE CUP FOR WHICH THE ITEM IS DESIGNED,EXPRESSED IN OUNCES. 1B MODE REPLY 0 ATDTB 10FREQUENCY IN HERTZ,CURRENT,VACUUM PUMP MOTOR VACUUM PUMP MOTOR CURRENT FREQUENCY IN HERTZ THE CYCLES PER SECOND (HERTZ) OF ALTERNATING CURRENT FOR WHICH THE VACUUM PUMP MOTOR IS DESIGNED. 1B MODE REPLY 0 ATDWJ /D/ 10CAPACITY IN SQUARE FEET,RADIATION RADIATION CAPACITY IN SQUARE FEET THE RATED OR DESIGNED RADIATION CAPACITY OF THE ITEM,EXPRESSED IN SQUARE FEET. 2D AND 1B MODE REPLY21AA942AM10 ATDXJ 10CAPACITY,MOTOR,SPRING SPRING MOTOR CAPACITY THE CAPACITY OF THE SPRING MOTOR. 2D AND 1B MODE REPLY21AA051AC20 ATDYH 02DESIGN,STRUCTURAL STRUCTURAL DESIGN THE STRUCTURAL DESIGN OF THE ITEM. 2D MODE REPLY 22AH792AA78 ATDZD 19PHASE,MOTOR,VACUUM PUMP VACUUM PUMP MOTOR PHASE THE NUMBER OF ALTERNATING CURRENT PHASES FOR WHICH THE VACUUM PUMP MOTOR IS DESIGNED. SELECT REPLY CODE 10AD02 ATEAJ 10VOLTAGE RATING,BOARD,COPY,ILLUMINATED ILLUMINATED COPY BOARD VOLTAGE RATING THE TYPE AND AMOUNT OF VOLTAGE FOR WHICH THE ILLUMINATED COPY BOARD IS DESIGNED. 1D AND 1B MODE REPLY12AG13 ATEBB 10FREQUENCY IN HERTZ,CURRENT,ILLUMINATED COPY BOARD ILLUMINATED COPY BOARD CURRENT FREQUENCY IN HERTZ THE CYCLES PER SECOND /HERTZ/ OF ALTERNATING CURRENT FOR WHICH THE ILLUMINATED COPY BOARD IS DESIGNED. 1B MODE REPLY 0 ATECB 10WATTAGE RATING,BOARD,COPY,ILLUMINATED ILLUMINATED COPY BOARD WATTAGE RATING THE MAXIMUM AMOUNT OF POWER FOR WHICH THE ILLUMINATED COPY BOARD IS DESIGNED,EXPRESSED IN WATTS. 1B MODE REPLY 0 ATEDJ 10VOLTAGE RATING,MOTOR,DRIVE,FOCUSING FOCUSING DRIVE MOTOR VOLTAGE RATING THE TYPE AND AMOUNT OF VOLTAGE FOR WHICH THE FOCUSING DRIVE MOTOR IS DESIGNED. 1D AND 1B MODE REPLY12AG13 ATEEB 10FREQUENCY IN HERTZ,CURRENT,FOCUSING DRIVE MOTOR FOCUSING DRIVE MOTOR CURRENT FREQUENCY IN HERTZ THE CYCLES PER SECOND (HERTZ) OF ALTERNATING CURRENT FOR WHICH THE FOCUSING DRIVE MOTOR IS DESIGNED. 1B MODE REPLY 0 ATEFD 19PHASE,MOTOR,FOCUSING DRIVE FOCUSING DRIVE MOTOR PHASE THE NUMBER OF ALTERNATING CURRENT PHASES FOR WHICH THE FOCUSING DRIVE MOTOR IS DESIGNED. SELECT REPLY CODE 10AD02 ATEGG /D/ 19AGENCY CONTROLLING ACCESSORY LIST DOCUMENT,GOVERNMENT GOVERNMENT AGENCY CONTROLLING ACCESSORY LIST DOCUMENT THE NAME OF THE GOVERNMENT AGENCY CONTROLLING THE ACCESSORY LIST DOCUMENT. FULL TEXT WRITE-IN 0 ATEHG /D/ 19ASSIGNEE,NUMBER,GOVERNMENT TYPE GOVERNMENT TYPE NUMBER ASSIGNEE THE NAME OF THE GOVERNMENT ACTIVITY ASSIGNING THE TYPE NUMBER TO THE ITEM. FULL TEXT WRITE-IN 0 ATEJG 03DESIGNATION,TYPE TYPE DESIGNATION THE IDENTIFYING DESIGNATOR ASSIGNED TO THE ITEM. FULL TEXT WRITE-IN 0 ATEKG /D/ 19NUMBER,MOUNT,AIRCRAFT AIRCRAFT MOUNT NUMBER THE NUMBER ASSIGNED TO THE AIRCRAFT MOUNT. FULL TEXT WRITE-IN 0 ATELG /D/ 19ASSIGNEE,NUMBER,GOVERNMENT MOUNT GOVERNMENT MOUNT NUMBER ASSIGNEE THE NAME OF THE GOVERNMENT ACTIVITY ASSIGNING THE NUMBER TO THE MOUNT. FULL TEXT WRITE-IN 0 ATEMJ 04LENGTH,EXTENDED EXTENDED LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM WHEN IT IS IN AN EXTENDED POSITION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ATENJ 04LENGTH,CONTRACTED CONTRACTED LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM WHEN IT IS IN A CONTRACTED /COMPRESSED/ POSITION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ATEPJ 04THICKNESS,MAGAZINE MAGAZINE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 ATEQD 18TYPE,SCALE SCALE TYPE INDICATES THE TYPE OF SCALE. SELECT REPLY CODE 10AM12 ATERD /D/ 07PLATFORM,FOLDING FOLDING PLATFORM AN INDICATION OF WHETHER OR NOT A FOLDING PLATFORM IS PROVIDED. SELECT REPLY CODE 10AB22 ATESA 12QUANTITY,BEAM BEAM QUANTITY THE NUMBER OF BEAMS PROVIDED ON THE ITEM. 1A MODE REPLY 0 ATETD 19SYSTEM,SCALE,BEAM WEIGHT BEAM WEIGHT SCALE SYSTEM INDICATES THE BEAM WEIGHT MEASUREMENT SYSTEM USED. SELECT REPLY CODE 10AM14 ATEWJ T10RANGE,SCALE,BEAM WEIGHT BEAM WEIGHT SCALE RANGE AN INDICATION OF THE BEAM WEIGHT SCALE RANGE. 1D AND 1F MODE REPLY11AB10 ATEXJ 04DIAMETER,OUTSIDE,BRIM BRIM OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BRIM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ATEYJ 04DIAMETER,OUTSIDE,BOTTOM BOTTOM OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOTTOM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ATEZD /D/ 07TREATMENT,HEAT HEAT TREATMENT AN INDICATION OF WHETHER OR NOT A HEAT TREATMENT IS PROVIDED. IF PROVIDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB22 ATFAB 10CAPACITY IN OUNCES CAPACITY IN OUNCES THE CAPACITY OF THE ITEM,EXPRESSED IN OUNCES. 1B MODE REPLY 0 ATFBB /D/ 10MARKING IN OUNCES,LINE LINE MARKING IN OUNCES AN INDICATION OF THE GRADUATED LINE MARKING,EXPRESSED IN OUNCES. 1B MODE REPLY 0 ATFCD 18TYPE,GLASS GLASS TYPE INDICATES THE TYPE OF GLASS PROVIDED. SELECT REPLY CODE 10AM13 ATFDD 18TYPE,DESIGN,CUP CUP DESIGN TYPE INDICATES THE DESIGN TYPE CHARACTERISTIC/S/ OF THE CUP. SELECT REPLY CODE 10AK54 ATFED /D/ 07STEM,EXTENDED EXTENDED STEM AN INDICATION OF WHETHER OR NOT AN EXTENDED STEM IS INCLUDED. SELECT REPLY CODE 10AA49 ATFFD 14SHAPE,CUP CUP SHAPE THE PHYSICAL CONFIGURATION OF THE CUP. SELECT REPLY CODE 10AD07 ATFGD /D/ 07SECTION,FLEXIBLE FLEXIBLE SECTION AN INDICATION OF WHETHER OR NOT A FLEXIBLE SECTION IS INCLUDED. SELECT REPLY CODE 10AA49 ATFHJ 04LENGTH,SECTION,FLEXIBLE FLEXIBLE SECTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FLEXIBLE SECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ATFJJ 04DISTANCE FROM TUBE TOP,FLEXIBLE SECTION FLEXIBLE SECTION DISTANCE FROM TUBE TOP THE DISTANCE FROM THE FLEXIBLE SECTION TO THE TOP OF THE TUBE. 2D AND 1B MODE REPLY21AA051AC20 ATFKD /D/ 07FUZE,DETONATING,AUXILIARY AUXILIARY DETONATING FUZE AN INDICATION OF WHETHER OR NOT AN AUXILIARY DETONATING FUZE IS INCLUDED. SELECT REPLY CODE 10AA49 ATFLD /D/ 07BOOSTER BOOSTER AN INDICATION OF WHETHER OR NOT A BOOSTER IS INCLUDED. SELECT REPLY CODE 10AA49 ATFMD /D/ 07FEATURE,SELF-DESTROYING SELF-DESTROYING FEATURE AN INDICATION OF WHETHER OR NOT A SELF-DESTROYING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ATFND /D/ 07WRENCH,FUZE FUZE WRENCH AN INDICATION OF WHETHER OR NOT A FUZE WRENCH IS INCLUDED. SELECT REPLY CODE 10AA49 ATFPA 03DESIGNATOR,IDENTIFICATION,MATERIAL MATERIAL IDENTIFICATION DESIGNATOR A DESIGNATION ASSIGNED TO THE MATERIAL FOR THE PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 ATFQD 03DESIGNATION,TIME,ACTION ACTION TIME DESIGNATION A DESIGNATION INDICATING THE FUNCTIONAL TIME FACTOR INCORPORATED IN THE ITEM. SELECT REPLY CODE 10AJ27 ATFRJ 10TIME IN SECONDS,DELAY DELAY TIME IN SECONDS A NUMERIC VALUE INDICATING THE ELAPSED TIME INTERVAL OF THE ITEM,EXPRESSED IN SECONDS. 1D AND 1B MODE REPLY11AC20 ATFSD /D/ 07FEATURE,PIERCING,CONCRETE CONCRETE PIERCING FEATURE AN INDICATION OF WHETHER OR NOT A CONCRETE PIERCING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ATFTJ 10TRAVEL,MINIMUM,SAFE AIR SAFE AIR MINIMUM TRAVEL THE MINIMUM DISTANCE THE ITEM IS DESIGNED TO TRAVEL SAFELY. 1D AND 1B MODE REPLY11AA05 ATFWA 19NUMBER FOR WHICH DESIGNED,MODEL,MINE MINE MODEL NUMBER FOR WHICH DESIGNED THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE MINE FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 ATFXD /D/ 07DETONATOR,AUXILIARY AUXILIARY DETONATOR AN INDICATION OF WHETHER OR NOT AN AUXILIARY DETONATOR IS INCLUDED. SELECT REPLY CODE 10AA49 ATFYD /D/ 07BOOSTER,SEPARATE SEPARATE BOOSTER AN INDICATION OF WHETHER OR NOT A SEPARATE BOOSTER IS INCLUDED. SELECT REPLY CODE 10AA49 ATFZB 10TIME IN SECONDS,DELAY DELAY TIME IN SECONDS A NUMERIC VALUE INDICATING THE ELAPSED TIME INTERVAL OF THE ITEM,EXPRESSED IN SECONDS. 1B MODE REPLY 0 ATGAA 19NUMBER,MODEL,PRIMER DETONATOR PRIMER DETONATOR MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE PRIMER DETONATOR. 1A MODE REPLY 0 ATGBD /D/ 07PUNCH,CUTTING,INTEGRAL INTEGRAL CUTTING PUNCH AN INDICATION OF WHETHER OR NOT AN INTEGRAL CUTTING PUNCH IS INCLUDED. SELECT REPLY CODE 10AA49 ATGCD /D/ 07THREAD,MOUNTING,CASE CASE MOUNTING THREAD AN INDICATION OF WHETHER OR NOT CASE MOUNTING THREADS ARE INCLUDED. SELECT REPLY CODE 10AA49 ATGDD 13THREAD SERIES,MOUNTING MOUNTING THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A THREADED MOUNTING. SELECT REPLY CODE 10AH06 ATGED /D/ 07CONNECTION,ELECTRICAL,CASE THREADED CASE THREADED ELECTRICAL CONNECTION AN INDICATION OF WHETHER OR NOT A CASE THREADED ELECTRICAL CONNECTION/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 ATGFD 13THREAD SERIES,CONNECTION CONNECTION THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A THREADED CONNECTION. SELECT REPLY CODE 10AH06 ATGGA 19NUMBER,MODEL,CASE CASE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE CASE. 1A MODE REPLY 0 ATGHD 18TYPE,DETONATION,PERCUSSION PERCUSSION DETONATION TYPE INDICATES THE TYPE OF PERCUSSION DETONATION PROVIDED. SELECT REPLY CODE 10AM26 ATGJJ 10POWER RATING,EXPLOSIVE EXPLOSIVE POWER RATING THE VALUE OF EXPLOSIVE ENERGY FOR WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY11AA56 ATGKD /D/ 07FEATURE,CODED,COLOR COLOR CODED FEATURE AN INDICATION OF WHETHER OR NOT A COLOR CODED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ATGLD /D/ 07RIM RIM AN INDICATION OF WHETHER OR NOT A RIM IS INCLUDED. SELECT REPLY CODE 10AA49 ATGMJ 04DIAMETER,END,CHARGED CHARGED END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CHARGED END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ATGND 19CONDITION FOR WHICH DESIGNED,SURFACE SURFACE CONDITION FOR WHICH DESIGNED AN INDICATION OF THE SURFACE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK39 ATGPJ /D/ 10PRESSURE,VAPOR,REID REID VAPOR PRESSURE THE VAPOR PRESSURE FOR POTENTIALLY FLAMMABLE ITEMS,AS DETERMINED BY THE REID METHOD. 1D AND 1B MODE REPLY12AG20 ATGQJ 10GRADUATION,MAXIMUM,SCALE,BEAM WEIGHT BEAM WEIGHT SCALE MAXIMUM GRADUATION THE MAXIMUM GRADUATION VALUE ON A BEAM WEIGHT SCALE. 1D AND 1B MODE REPLY11AB10 ATGRD 18TYPE,DIAL DIAL TYPE INDICATES THE TYPE OF DIAL PROVIDED. SELECT REPLY CODE 10AM15 ATGSD /D/ 07FEATURE,GRADUATION,DIAL DIAL GRADUATION FEATURE AN INDICATION OF WHETHER OR NOT A DIAL GRADUATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ATGTD 19SYSTEM,SCALE,DIAL WEIGHT DIAL WEIGHT SCALE SYSTEM INDICATES THE DIAL WEIGHT MEASUREMENT SYSTEM USED. SELECT REPLY CODE 10AM14 ATGWJ T10RANGE,SCALE,DIAL WEIGHT DIAL WEIGHT SCALE RANGE AN INDICATION OF THE DIAL WEIGHT SCALE RANGE. 1D AND 1F MODE REPLY11AB10 ATGXJ 10GRADUATION,MAXIMUM,SCALE,DIAL WEIGHT DIAL WEIGHT SCALE MAXIMUM GRADUATION THE MAXIMUM GRADUATION VALUE ON A DIAL WEIGHT SCALE. 1D AND 1B MODE REPLY11AB10 ATGYF /D/T10RANGE IN CENTS,SCALE,COMPUTING COMPUTING SCALE RANGE IN CENTS THE COMPUTING SCALE RANGE,EXPRESSED IN CENTS. 1F MODE REPLY 0 ATGZB /D/ 10INTERVAL IN CENTS,SCALE,COMPUTING COMPUTING SCALE INTERVAL IN CENTS THE INTERVAL VALUE ON A COMPUTING SCALE,EXPRESSED IN CENTS. 1B MODE REPLY 0 ATHAA 10RATIO,COUNTING COUNTING RATIO THE MAXIMUM TO MINIMUM COUNTING RATIO,WITH THE LARGER RELATIVE PROPORTION GIVEN,THE LOWER VALUE HAVING AN IMPLIED /NOT GIVEN/ VALUE OF ONE /UNITY/. 1A MODE REPLY 0 ATHBA 12QUANTITY,RECEIVER,LOAD LOAD RECEIVER QUANTITY THE NUMBER OF LOAD RECEIVERS PROVIDED. 1A MODE REPLY 0 ATHCD 18TYPE,RECEIVER,LOAD LOAD RECEIVER TYPE INDICATES THE TYPE OF LOAD RECEIVER PROVIDED. SELECT REPLY CODE 10AM17 ATHDD /D/ 09MATERIAL,RECEIVER,LOAD LOAD RECEIVER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LOAD RECEIVER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ATHED /D/ 07BAR,TARE TARE BAR AN INDICATION OF WHETHER OR NOT A TARE BAR IS INCLUDED. SELECT REPLY CODE 10AA49 ATHFD /D/ 07WEIGHT,COUNTERPOISE COUNTERPOISE WEIGHT AN INDICATION OF WHETHER OR NOT COUNTERPOISE WEIGHTS ARE INCLUDED. SELECT REPLY CODE 10AA49 ATHGD /D/ 07WHEEL WHEEL AN INDICATION OF WHETHER OR NOT WHEELS ARE PROVIDED. SELECT REPLY CODE 10AB22 ATHHD /D/ 07FEATURE,DETERMINATION,SPECIFIC GRAVITY SPECIFIC GRAVITY DETERMINATION FEATURE AN INDICATION OF WHETHER OR NOT A SPECIFIC GRAVITY DETERMINATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ATHJD 18TYPE,MECHANISM,DIAL DIAL MECHANISM TYPE INDICATES THE TYPE OF DIAL MECHANISM PROVIDED. SELECT REPLY CODE 10AJ73 ATHKG /D/ 19CLASS,NATIONAL BUREAU OF STANDARDS NATIONAL BUREAU OF STANDARDS CLASS A CLASSIFICATION ASSIGNED TO THE ITEM BY THE NATIONAL BUREAU OF STANDARDS. FULL TEXT WRITE-IN 0 ATHLA 12QUANTITY,WEIGHT,UNIT,INDIVIDUAL INDIVIDUAL UNIT WEIGHT QUANTITY THE NUMBER OF INDIVIDUAL UNIT WEIGHTS INCLUDED WITH THE ITEM. 1A MODE REPLY 0 ATHMG /D/ 19DENOMINATION AND QUANTITY,WEIGHT,INDIVIDUAL UNIT INDIVIDUAL UNIT WEIGHT DENOMINATION AND QUANTITY THE DENOMINATION AND NUMBER OF INDIVIDUAL UNIT WEIGHTS SUPPLIED WITH THE ITEM. FULL TEXT WRITE-IN 0 ATHND /D/ 09MATERIAL,WEIGHT,INDIVIDUAL UNIT INDIVIDUAL UNIT WEIGHT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INDIVIDUAL UNIT WEIGHT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ATHPD /D/ 17SURFACE TREATMENT,WEIGHT,INDIVIDUAL UNIT INDIVIDUAL UNIT WEIGHT SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS AN INDIVIDUAL UNIT WEIGHT SURFACE. SELECT REPLY CODE 10AD09 ATHQA 12QUANTITY,WEIGHT,INDIVIDUAL FRACTIONAL UNIT INDIVIDUAL FRACTIONAL UNIT WEIGHT QUANTITY THE NUMBER OF INDIVIDUAL FRACTIONAL UNIT WEIGHTS INCLUDED WITH THE ITEM. 1A MODE REPLY 0 ATHRG /D/ 19DENOMINATION AND QUANTITY,WEIGHT,INDIVIDUAL FRACTIONAL UNIT INDIVIDUAL FRACTIONAL UNIT WEIGHT DENOMINATION AND QUANTITY THE DENOMINATION AND NUMBER OF INDIVIDUAL FRACTIONAL UNIT WEIGHTS SUPPLIED WITH THE ITEM. FULL TEXT WRITE-IN 0 ATHSD /D/ 09MATERIAL,WEIGHT,INDIVIDUAL FRACTIONAL UNIT INDIVIDUAL FRACTIONAL UNIT WEIGHT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INDIVIDUAL FRACTIONAL UNIT WEIGHT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ATHTA 12QUANTITY,WEIGHT,INDIVIDUAL RIDER INDIVIDUAL RIDER WEIGHT QUANTITY THE NUMBER OF INDIVIDUAL RIDER WEIGHTS INCLUDED WITH THE ITEM. 1A MODE REPLY 0 ATHWG /D/ 19DENOMINATION AND QUANTITY,WEIGHT,INDIVIDUAL RIDER INDIVIDUAL RIDER WEIGHT DENOMINATION AND QUANTITY THE DENOMINATION AND NUMBER OF INDIVIDUAL RIDER WEIGHTS SUPPLIED WITH THE ITEM. FULL TEXT WRITE-IN 0 ATHXD /D/ 07FORCEPS FORCEPS AN INDICATION OF WHETHER OR NOT FORCEPS ARE INCLUDED. SELECT REPLY CODE 10AA49 ATHYD /D/ 07BOX,FITTED FITTED BOX AN INDICATION OF WHETHER OR NOT A FITTED BOX IS INCLUDED. SELECT REPLY CODE 10AA49 ATHZJ 19DENOMINATION DENOMINATION INDICATES THE DENOMINATION OF THE ITEM. 1D AND 1B MODE REPLY12AG67 ATJAG 19MARKING,WEIGHT WEIGHT MARKING MARKINGS INCLUDED ON THE WEIGHT FOR PURPOSE OF READY IDENTIFICATION. FULL TEXT WRITE-IN 0 ATJBJ 10CAPACITY,WEIGHING WEIGHING CAPACITY THE WEIGHING CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 ATJCD /D/ 09MATERIAL,BEAM BEAM MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BEAM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ATJDJ /D/ 04LENGTH BETWEEN STIRRUP KNIFE EDGES,BEAM BEAM LENGTH BETWEEN STIRRUP KNIFE EDGES THE DIMENSION ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE STIRRUP KNIFE EDGES. 2D AND 1B MODE REPLY21AA051AC20 ATJEA 12QUANTITY,GRADUATION,BEAM ARM BEAM ARM GRADUATION QUANTITY THE NUMBER OF GRADUATION/S/ ON EACH BEAM ARM. 1A MODE REPLY 0 ATJFA 12QUANTITY,RIDER,BEAM BEAM RIDER QUANTITY THE NUMBER OF BEAM RIDERS INCLUDED WITH THE ITEM. 1A MODE REPLY 0 ATJGJ 10WEIGHT,RIDER,BEAM BEAM RIDER WEIGHT A RELATIVE MEASURE OF THE MASS OF A BEAM RIDER WITH RESPECT TO ITS DENSITY. 1D AND 1B MODE REPLY12AG67 ATJHD 18TYPE,DAMPER,BEAM BEAM DAMPER TYPE INDICATES THE TYPE OF BEAM DAMPER. SELECT REPLY CODE 10AM18 ATJJD /D/ 09MATERIAL,EDGE,KNIFE KNIFE EDGE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE KNIFE EDGES ARE FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ATJKD 19SOURCE,POWER POWER SOURCE THE SOURCE OF POWER WHICH DRIVES THE ITEM. SELECT REPLY CODE 10AG27 ATJLG 19NAME,MANUFACTURER,ENGINE ENGINE MANUFACTURER NAME THE NAME OF THE MANUFACTURER OF THE ENGINE FURNISHED. FULL TEXT WRITE-IN 0 ATJNA 12QUANTITY,CATHEAD CATHEAD QUANTITY THE NUMBER OF CATHEADS INCLUDED. 1A MODE REPLY 0 ATJPD 11METHOD,TRANSPORT TRANSPORT METHOD THE MEANS BY WHICH THE ITEM IS TRANSPORTED. SELECT REPLY CODE 10AJ17 ATJQD /D/ 07FEATURE,DRILLING,CORE CORE DRILLING FEATURE AN INDICATION OF WHETHER OR NOT A CORE DRILLING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ATJRD 18TYPE,EDGE,CUTTING CUTTING EDGE TYPE INDICATES THE TYPE OF CUTTING EDGE PROVIDED. SELECT REPLY CODE 10AJ54 ATJSD 02DESIGN,EDGE,CUTTING CUTTING EDGE DESIGN THE DESIGN OF THE CUTTING EDGE ON THE ITEM. SELECT REPLY CODE 10AL25 ATJWD 18TYPE,TOOTH,ROLLER ROLLER TOOTH TYPE INDICATES THE TYPE OF TEETH ON THE ROLLER. SELECT REPLY CODE 10AJ46 ATJXD /D/ 07SPIKE,PILOT PILOT SPIKE AN INDICATION OF WHETHER OR NOT A PILOT SPIKE IS INCLUDED. SELECT REPLY CODE 10AA49 ATJYD /D/ 07CUTTER,PILOT PILOT CUTTER AN INDICATION OF WHETHER OR NOT A PILOT CUTTER IS INCLUDED. SELECT REPLY CODE 10AA49 ATJZD 13THREAD DIRECTION,JOINT JOINT THREAD DIRECTION THE DIRECTION OF THE JOINT THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 ATKAD 13THREAD LOCATION,JOINT JOINT THREAD LOCATION THE PORTION/S/ OF A JOINT ON WHICH THE THREAD/S/ IS LOCATED. SELECT REPLY CODE 10AJ91 ATKBD 13THREAD SERIES,JOINT JOINT THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A JOINT. SELECT REPLY CODE 10AH06 ATKCG 13THREAD SERIES MODIFICATION,JOINT JOINT THREAD SERIES MODIFICATION AN INDICATION OF THE MODIFICATION OF THE JOINT THREAD SERIES. FULL TEXT WRITE-IN 0 ATKDD /D/ 07FEATURE,THREAD,JOINT STEP JOINT STEP THREAD FEATURE AN INDICATION OF WHETHER OR NOT A JOINT STEP THREAD FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ATKEJ 04THREAD DIAMETER,JOINT JOINT THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE JOINT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ATKFJ 04THREAD LENGTH,JOINT JOINT THREAD LENGTH A MEASUREMENT OF THE EXTENT OF JOINT THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL THREAD AXIS. 2D AND 1B MODE REPLY21AA051AC20 ATKGD 02DESIGN,HEAD HEAD DESIGN THE DESIGN OF THE HEAD. SELECT REPLY CODE 10AK54 ATKHG /D/ 04DIAMETER AND MAXIMUM BORING DEPTH,AUGER,ACCOMMODATED ACCOMMODATED AUGER DIAMETER AND MAXIMUM BORING DEPTH THE MAXIMUM DEPTH AN ACCOMMODATED AUGER DIAMETER IS CAPABLE OF BORING. FULL TEXT WRITE-IN 0 ATKJD /D/ 07BORING FEATURE,ANGLE ANGLE BORING FEATURE AN INDICATION OF WHETHER OR NOT AN ANGLE BORING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ATKKB 04ANGLE FROM VERTICAL FORE IN DEG,BORING BORING ANGLE FROM VERTICAL FORE IN DEG THE ANGLE AT WHICH THE ITEM WILL BORE FROM VERTICAL FORE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ATKLB 04ANGLE FROM VERTICAL AFT IN DEG,BORING BORING ANGLE FROM VERTICAL AFT IN DEG THE ANGLE AT WHICH THE ITEM WILL BORE FROM VERTICAL AFT,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ATKMB 04ANGLE FROM VERTICAL SIDEWAYS IN DEG,BORING BORING ANGLE FROM VERTICAL SIDEWAYS IN DEG THE ANGLE AT WHICH THE ITEM WILL BORE FROM VERTICAL SIDEWAYS,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ATKND /D/ 07AUGER AUGER AN INDICATION OF WHETHER OR NOT AN AUGER(S) IS FURNISHED. SELECT REPLY CODE 10AA55 ATKPD /D/ 07ATTACHMENT,RAISING,POLE POLE RAISING ATTACHMENT AN INDICATION OF WHETHER OR NOT A POLE RAISING ATTACHMENT IS INCLUDED. SELECT REPLY CODE 10AA49 ATKQD /D/ 07DRUM,HOIST HOIST DRUM AN INDICATION OF WHETHER OR NOT A HOIST DRUM IS INCLUDED. SELECT REPLY CODE 10AA49 ATKRD /D/ 07CATHEAD CATHEAD AN INDICATION OF WHETHER OR NOT A CATHEAD(S) IS INCLUDED. SELECT REPLY CODE 10AA49 ATKSD 13THREAD LOCATION,END,FIRST FIRST END THREAD LOCATION THE PORTION(S)OF THE FIRST END ON WHICH THE THREAD(S) IS LOCATED. SELECT REPLY CODE 10AJ91 ATKTD 13THREAD SERIES,END,FIRST FIRST END THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF THE FIRST END. SELECT REPLY CODE 10AH06 ATKWG 13THREAD SERIES MODIFICATION,END,FIRST FIRST END THREAD SERIES MODIFICATION AN INDICATION OF THE MODIFICATION ON THE FIRST END THREAD SERIES. FULL TEXT WRITE-IN 0 ATKXD /D/ 07FEATURE,THREAD,FIRST END STEP FIRST END STEP THREAD FEATURE AN INDICATION OF WHETHER OR NOT A FIRST END STEP THREAD FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ATKYJ 04THREAD DIAMETER,FIRST END FIRST END THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE FIRST END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ATKZJ 04THREAD LENGTH,END,FIRST FIRST END THREAD LENGTH A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL THREAD AXIS. 2D AND 1B MODE REPLY21AA051AC20 ATLAD 13THREAD LOCATION,END,SECOND SECOND END THREAD LOCATION THE PORTION(S) OF THE SECOND END ON WHICH THE THREAD(S) IS LOCATED. SELECT REPLY CODE 10AJ91 ATLBD 13THREAD SERIES,END,SECOND SECOND END THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF THE SECOND END. SELECT REPLY CODE 10AH06 ATLCG 13THREAD SERIES MODIFICATION,END,SECOND SECOND END THREAD SERIES MODIFICATION AN INDICATION OF THE MODIFICATION OF THE SECOND END THREAD SERIES. FULL TEXT WRITE-IN 0 ATLDD /D/ 07FEATURE,THREAD,SECOND END STEP SECOND END STEP THREAD FEATURE AN INDICATION OF WHETHER OR NOT A SECOND END STEP THREAD FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ATLEJ 04THREAD DIAMETER,SECOND END SECOND END THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE SECOND END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ATLFJ 04THREAD LENGTH,END,SECOND SECOND END THREAD LENGTH A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL THREAD AXIS. 2D AND 1B MODE REPLY21AA051AC20 ATLGG /D/ 04DIMENSION,OPENING,JAW JAW OPENING DIMENSION THE DIMENSION/S/ OF THE JAW OPENING. FULL TEXT WRITE-IN 0 ATLHD /D/ 09MATERIAL,PLANE PLANE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PLANE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ATLJD /D/ 07STIRRUP,PAN,MAGNETIC MAGNETIC PAN STIRRUP AN INDICATION OF WHETHER OR NOT A MAGNETIC PAN STIRRUP IS INCLUDED. SELECT REPLY CODE 10AA49 ATLKJ 04WIDTH,OVERALL,PAN PAN OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A PAN,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 ATLLJ 04HEIGHT,STIRRUP STIRRUP HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A STIRRUP,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 ATLMD 18TYPE,ARREST,PAN STIRRUP PAN STIRRUP ARREST TYPE INDICATES THE TYPE OF PAN STIRRUP ARREST PROVIDED. SELECT REPLY CODE 10AM19 ATLND 18TYPE,INDICATOR,SCALE SCALE INDICATOR TYPE INDICATES THE TYPE OF SCALE INDICATOR PROVIDED. SELECT REPLY CODE 10AJ12 ATLPD 07ADJUSTABILITY,SCALE SCALE ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE SCALE IS ADJUSTABLE. SELECT REPLY CODE 10AB00 ATLQD /D/ 07DEVICE,WEIGHING,QUICK QUICK WEIGHING DEVICE AN INDICATION OF WHETHER OR NOT A QUICK WEIGHING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 ATLRD 18TYPE,DEVICE,QUICK WEIGHING QUICK WEIGHING DEVICE TYPE INDICATES THE TYPE OF QUICK WEIGHING DEVICE. SELECT REPLY CODE 10AC58 ATLSJ T10RANGE,WEIGHT,QUICK WEIGHING DEVICE QUICK WEIGHING DEVICE WEIGHT RANGE AN INDICATION OF THE QUICK WEIGHING DEVICE WEIGHT RANGE. 1D AND 1F MODE REPLY12AG67 ATLTD /D/ 09MATERIAL,FRAME,CASE CASE FRAME MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CASE FRAME IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ATLWD /D/ 09MATERIAL,FLOOR,CASE CASE FLOOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CASE FLOOR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ATLXD 11METHOD,ACCESS,CASE CASE ACCESS METHOD THE MEANS OF ACCESS INTO THE CASE. SELECT REPLY CODE 10AM20 ATLYA 12QUANTITY,FEET,ADJUSTABLE,CASE CASE ADJUSTABLE FEET QUANTITY THE NUMBER OF ADJUSTABLE FEET ON THE CASE. 1A MODE REPLY 0 ATLZA 12QUANTITY,FEET,FIXED,CASE CASE FIXED FEET QUANTITY THE NUMBER OF FIXED FEET ON THE CASE. 1A MODE REPLY 0 ATMAA 12QUANTITY,INDICATOR,CASE LEVELING CASE LEVELING INDICATOR QUANTITY THE NUMBER OF CASE LEVELING INDICATORS INCLUDED. 1A MODE REPLY 0 ATMBD 18TYPE,INDICATOR,CASE LEVELING CASE LEVELING INDICATOR TYPE INDICATES THE TYPE OF CASE LEVELING INDICATOR. SELECT REPLY CODE 10AJ73 ATMCA 12QUANTITY,DRAWER,CASE CASE DRAWER QUANTITY THE NUMBER OF DRAWERS IN THE CASE. 1A MODE REPLY 0 ATMDD 08LOCATION,BEAM BEAM LOCATION INDICATES THE LOCATION OF THE BEAM. SELECT REPLY CODE 10AJ91 ATMEJ T10RANGE,GRADUATION,BEAM BEAM GRADUATION RANGE AN INDICATION OF THE BEAM GRADUATION RANGE. 1D AND 1F MODE REPLY12AG67 ATMFJ 10GRADUATION,BEAM BEAM GRADUATION THE GRADUATION VALUE ON A BEAM. 1D AND 1B MODE REPLY12AG67 ATMGD 18TYPE,RECEPTACLE RECEPTACLE TYPE INDICATES THE TYPE OF RECEPTACLE PROVIDED. SELECT REPLY CODE 10AM17 ATMHD /D/ 09MATERIAL,RECEPTACLE RECEPTACLE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE RECEPTACLE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ATMJD /D/ 07REST,PAN,ADJUSTABLE BALANCE ADJUSTABLE BALANCE PAN REST AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE BALANCE PAN REST IS INCLUDED. SELECT REPLY CODE 10AA49 ATMKD /D/ 07LEG,ADJUSTABLE ADJUSTABLE LEG AN INDICATION OF WHETHER OR NOT ADJUSTABLE LEGS ARE INCLUDED. SELECT REPLY CODE 10AA49 ATMLD /D/ 07LEVEL,SPIRIT SPIRIT LEVEL AN INDICATION OF WHETHER OR NOT A SPIRIT LEVEL IS INCLUDED. SELECT REPLY CODE 10AA49 ATMMD 18TYPE,ASSEMBLY ASSEMBLY TYPE INDICATES THE TYPE OF ASSEMBLY. SELECT REPLY CODE 10AG25 ATMND 11METHOD,LOCATION,ANGULAR UNBALANCE ANGULAR UNBALANCE LOCATION METHOD THE MEANS OF LOCATING THE ANGULAR UNBALANCE. SELECT REPLY CODE 10AM22 ATMPJ 10CAPACITY,WEIGHT,MAXIMUM WORKING MAXIMUM WORKING WEIGHT CAPACITY THE MAXIMUM WEIGHT,UNDER WORKING CONDITIONS,THAT THE ITEM IS DESIGNED TO SUPPORT. 1D AND 1B MODE REPLY12AG67 ATMQJ 10CAPACITY,WEIGHT,MINIMUM WORKING MINIMUM WORKING WEIGHT CAPACITY THE MINIMUM WEIGHT,UNDER WORKING CONDITIONS,THAT THE ITEM IS DESIGNED TO SUPPORT. 1D AND 1B MODE REPLY12AG67 ATMRJ 04DIAMETER,MAXIMUM,SWING SWING MAXIMUM DIAMETER THE MAXIMUM DIAMETER THE ITEM WILL SWING. 1D AND 1B MODE REPLY11AA05 ATMSJ 04DISTANCE BETWEEN BEARING SHOULDERS,MAXIMUM MAXIMUM DISTANCE BETWEEN BEARING SHOULDERS THE MAXIMUM DISTANCE BETWEEN THE BEARING SHOULDERS. 1D AND 1B MODE REPLY11AA05 ATMTJ 04DIAMETER AT BEARING,MAXIMUM,SHAFT SHAFT MAXIMUM DIAMETER AT BEARING THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHAFT AT THE BEARING,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 ATMWD 18TYPE,SUPPORT,WORK WORK SUPPORT TYPE INDICATES THE TYPE OF WORK SUPPORT. SELECT REPLY CODE 10AM23 ATMXJ 10SENSITIVITY RATING,VIBRATION VIBRATION SENSITIVITY RATING THE VIBRATION SENSITIVITY FOR WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY11AA05 ATMYD /D/ 07ATTACHMENT,DRILLING,INTEGRAL CORRECTION INTEGRAL CORRECTION DRILLING ATTACHMENT AN INDICATION OF WHETHER OR NOT AN INTEGRAL CORRECTION DRILLING ATTACHMENT IS INCLUDED. SELECT REPLY CODE 10AA49 ATMZA /D/ 12QUANTITY,SPINDLE,DRILLING DRILLING SPINDLE QUANTITY THE NUMBER OF DRILLING SPINDLES PROVIDED. 1A MODE REPLY 0 ATNAD /D/ 18TYPE,DEVICE,CORRECTION WEIGHT ATTACHMENT CORRECTION WEIGHT ATTACHMENT DEVICE TYPE INDICATES THE TYPE OF DEVICE USED FOR ATTACHING CORRECTION WEIGHTS. SELECT REPLY CODE 10AM24 ATNBD 18TYPE,LOAD,HEAD HEAD LOAD TYPE INDICATES THE TYPE OF LOAD IN THE HEAD. SELECT REPLY CODE 10AM25 ATNCJ 10SIZE,SURFACE,DRIVE DRIVE SURFACE SIZE A NUMERIC VALUE WHICH INDICATES THE SIZE OF THE DRIVE SURFACE. 2D AND 1B MODE REPLY21AA051AC20 ATNDH /D/ 14SHAPE AND LOCATION,SURFACE,DRIVE DRIVE SURFACE SHAPE AND LOCATION THE PHYSICAL CONFIGURATION OF THE DRIVE SURFACE AND ITS LOCATION ON THE ITEM. 2D MODE REPLY 23AD073AJ91 ATNED 19CHARACTERISTIC,FOLDED FOLDED CHARACTERISTIC AN INDICATION OF THE FOLDED CHARACTERISTIC OF THE ITEM. SELECT REPLY CODE 10AE33 ATNFB 10GRADUATION,CHART,COLOR,PH PH COLOR CHART GRADUATION THE PH COLOR GRADUATION OF THE CHART. 1B MODE REPLY 0 ATNGF T10RANGE,VALUE,PH PH VALUE RANGE THE MINIMUM AND MAXIMUM LIMITS OF PH VALUES. 1F MODE REPLY 0 ATNHD /D/ 09MATERIAL,DISPENSER DISPENSER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH A DISPENSER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ATNJA /D/ 12QUANTITY ACCOMMODATED,ROLL ROLL QUANTITY ACCOMMODATED THE NUMBER OF ROLLS ACCOMMODATED BY THE ITEM. . 1A MODE REPLY 0 ATNKD /D/ 07DISPENSER DISPENSER AN INDICATION OF WHETHER OR NOT A DISPENSER IS INCLUDED. SELECT REPLY CODE 10AA49 ATNLD 19FEATURE,WASH,ACID ACID WASH FEATURE AN INDICATION OF THE ACID WASH FEATURE. SELECT REPLY CODE 10AF09 ATNMB 10CONTENT IN MILLIGRAMS,ASH,MAXIMUM MAXIMUM ASH CONTENT IN MILLIGRAMS AN INDICATION OF THE MAXIMUM AMOUNT OF ASH CONTAINED,EXPRESSED IN MILLIGRAMS. 1B MODE REPLY 0 ATNND /D/ 07FEATURE,HARDENING HARDENING FEATURE AN INDICATION OF WHETHER OR NOT A HARDENING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ATNPD 19PRECIPITATE FOR WHICH DESIGNED PRECIPITATE FOR WHICH DESIGNED INDICATES THE TYPE OF PRECIPITATE(S) FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL18 ATNQB 10PERCENT,CONCENTRATION,SOLUTION SOLUTION CONCENTRATION PERCENT THE PERCENT OF SOLUTION CONCENTRATION. 1B MODE REPLY 0 ATNRD 18TYPE FOR WHICH DESIGNED,HOLDER HOLDER TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF HOLDER FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AE98 ATNSJ T10RANGE,COLOR COLOR RANGE THE RANGE OF VALUES OF THE COLOR. 1D AND 1F MODE REPLY12AF03 ATNTB 10GRADUATION,COLOR COLOR GRADUATION AN INDICATION OF THE DEGREE OF GRADUATION OF THE COLOR. 1B MODE REPLY 0 ATNWD /D/ 18TYPE FOR WHICH DESIGNED,LIGHT LIGHT TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF LIGHT WITH WHICH THE ITEM IS DESIGNED TO BE USED. SELECT REPLY CODE 10AG41 ATNXD 18TYPE,SOLUTION,INDICATOR INDICATOR SOLUTION TYPE INDICATES THE TYPE OF INDICATOR SOLUTION PROVIDED. SELECT REPLY CODE 10AB75 ATNYD 18TYPE,SYSTEM,VIEWING VIEWING SYSTEM TYPE INDICATES THE TYPE OF VIEWING SYSTEM FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AM07 ATNZJ /D/ 19FINISH AND LOCATION,SURFACE SURFACE FINISH AND LOCATION DESIGNATES THE SPECIFIC ROUGHNESS RATING REPRESENTING THE ARITHMETIC AVERAGE DEVIATION OF THE SURFACE FROM THE MEANLINE IN A PROFILE /THE ARITHMETIC AVERAGE AMOUNT OF DEVIATION OF THE PEAKS AND VALLEYS FROM A MEANLINE/ AND ITS LOCATION ON AN ITEM. 2D AND 1B MODE REPLY21AE863AJ91 ATPAA 12QUANTITY,PLATE PLATE QUANTITY THE NUMBER OF PLATES INCLUDED IN THE ITEM. 1A MODE REPLY 0 ATPBJ /D/ 10TEMP RATING,AMBIENT AMBIENT TEMP RATING THE TEMPERATURE OF THE MEDIUM SURROUNDING THE ITEM AT WHICH IT CAN BE OPERATED CONTINUOUSLY. 2D AND 1B MODE REPLY21AB361AC20 ATPCA 12QUANTITY,STEP STEP QUANTITY THE NUMBER OF STEPS PROVIDED. 1A MODE REPLY 0 ATPDJ /D/ 10TIME,OPERATING,MAXIMUM MAXIMUM OPERATING TIME THE MAXIMUM AMOUNT OF TIME FOR WHICH THE ITEM IS DESIGNED TO BE ENERGIZED AT A RATED LOAD WITHOUT DETERIORATING. 1D AND 1B MODE REPLY12AH68 ATPEJ /D/ 10TIME,DE-ENERGIZED,MINIMUM MINIMUM DE-ENERGIZED TIME THE MINIMUM AMOUNT OF TIME REQUIRED FOR THE ITEM TO BE DE-ENERGIZED. 1D AND 1B MODE REPLY12AH68 ATPFJ /D/ 04LENGTH,PROTRUSION,MOUNTING FACILITY MOUNTING FACILITY PROTRUSION LENGTH THE MEASUREMENT OF THE DISTANCE THAT THE MOUNTING FACILITY PROTRUDES FROM THE MOUNTING SURFACE. 2D AND 1B MODE REPLY21AA051AC20 ATPGJ 04DIAMETER,PLATE PLATE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PLATE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ATPHD 18TYPE,UNIT,SEPARATION SEPARATION UNIT TYPE INDICATES THE TYPE OF SEPARATION UNIT PROVIDED. SELECT REPLY CODE 10AK54 ATPJA 12QUANTITY,PLACE,HEAD HEAD PLACE QUANTITY THE NUMBER OF PLACES PROVIDED IN THE HEAD. 1A MODE REPLY 0 ATPKJ 10CAPACITY,CAKE CAKE CAPACITY THE AMOUNT OF LIQUID,GRANULES,AND THE LIKE,THE CAKE WILL HOLD. 1D AND 1B MODE REPLY12AG67 ATPLJ /D/ 10VOLTAGE RATING TYPE IN VOLTS,MOTOR MOTOR VOLTAGE RATING TYPE IN VOLTS THE TYPE AND VALUE/S/ OF POTENTIAL FOR WHICH THE MOTOR IS RATED,EXPRESSED IN VOLTS. 2D AND 1B MODE REPLY21AB621AC20 ATPMG 04SIZE,CONTAINER,PLACE PLACE CONTAINER SIZE DESIGNATES THE SIZE OF THE CONTAINER THAT EACH PLACE WILL ACCOMMODATE. FULL TEXT WRITE-IN 0 ATPNJ 10CAPACITY,BOWL BOWL CAPACITY THE AMOUNT OF LIQUID,GRANULES,AND THE LIKE,THE BOWL WILL HOLD. 1D AND 1B MODE REPLY12AG67 ATPPA 12QUANTITY,SLOT SLOT QUANTITY THE NUMBER OF SLOTS IN THE ITEM. 1A MODE REPLY 0 ATPQD /D/ 07CAP,SAFETY SAFETY CAP AN INDICATION OF WHETHER OR NOT A SAFETY CAP IS INCLUDED. SELECT REPLY CODE 10AA49 ATPRB 10SPEED RATING IN RPM,MAXIMUM MAXIMUM SPEED RATING IN RPM THE MAXIMUM SPEED AT WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 ATPSJ /D/ 10CONSUMPTION RATING CONSUMPTION RATING THE CONSUMPTION RATE AT WHICH THE ITEM IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY12AG20 ATPTD /D/ 07BOWL,GUARD GUARD BOWL AN INDICATION OF WHETHER OR NOT A GUARD BOWL IS INCLUDED. SELECT REPLY CODE 10AA49 ATPWG 19CONTROLS,FURNISHED FURNISHED CONTROLS CONTROLS FURNISHED WHICH ARE NOT SPECIFIED ELSEWHERE. FULL TEXT WRITE-IN 0 ATPXD 18TYPE,ROLL ROLL TYPE INDICATES THE TYPE OF ROLL/S/ PROVIDED. SELECT REPLY CODE 10AM21 ATPYA 12QUANTITY,ROLL ROLL QUANTITY THE NUMBER OF ROLLS PROVIDED. 1A MODE REPLY 0 ATPZJ 04DIAMETER,ROLL ROLL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ROLL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ATQAJ 04WIDTH,FACE,ROLL ROLL FACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ROLL FACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ATQBJ 10CAPACITY,OUTPUT OUTPUT CAPACITY THE RATED OUTPUT CAPACITY OF THE ITEM. 2D AND 1B MODE REPLY22AG201AC20 ATQCJ 10SIZE,PRODUCT PRODUCT SIZE DESIGNATES THE SIZE OF PRODUCT PRODUCED BY THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 ATQDD /D/ 07DOCUMENT,LIST,COMPONENT COMPONENT LIST DOCUMENT AN INDICATION OF WHETHER OR NOT A DOCUMENT CONTAINING A LIST OF COMPONENTS IS INCLUDED. SELECT REPLY CODE 10AA49 ATQED 05DIRECTION,OPERATING,HANDLE HANDLE OPERATING DIRECTION AN INDICATION OF THE HANDLE OPERATING DIRECTION. SELECT REPLY CODE 10AJ69 ATQFA 12QUANTITY,WHEEL,SINGLE SINGLE WHEEL QUANTITY THE NUMBER OF SINGLE WHEELS PROVIDED. 1A MODE REPLY 0 ATQGA 12QUANTITY,WHEEL,DUAL DUAL WHEEL QUANTITY THE NUMBER OF DUAL WHEELS PROVIDED. 1A MODE REPLY 0 ATQHA 12QUANTITY,TIRE TIRE QUANTITY THE NUMBER OF TIRES PROVIDED. 1A MODE REPLY 0 ATQJJ 04WIDTH,JAW JAW WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE JAW,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ATQKD /D/ 07MOVER,PRIME PRIME MOVER AN INDICATION OF WHETHER OR NOT A PRIME MOVER IS INCLUDED. SELECT REPLY CODE 10AA49 ATQLJ 04DIAMETER,PULLEY PULLEY DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PULLEY,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ATQMJ 04WIDTH,FACE,PULLEY PULLEY FACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PULLEY FACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ATQNA 12QUANTITY,GROOVE,PULLEY PULLEY GROOVE QUANTITY THE NUMBER OF PULLEY GROOVES INCLUDED IN THE ITEM. 1A MODE REPLY 0 ATQPJ /D/ 04DIAMETER FOR WHICH DESIGNED,OUTSIDE,CASING/PIPE CASING/PIPE OUTSIDE DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CASING OR PIPE FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ATQQA /D/ 12QUANTITY,SEGMENT,COMPLETE RING COMPLETE RING SEGMENT QUANTITY THE NUMBER OF SEGMENTS REQUIRED FOR A COMPLETE RING. 1A MODE REPLY 0 ATQRA 12QUANTITY,VALVE VALVE QUANTITY THE NUMBER OF VALVES PROVIDED. 1A MODE REPLY 0 ATQSD 18TYPE,GATE,VALVE VALVE GATE TYPE INDICATES THE TYPE OF GATE IN THE VALVE. SELECT REPLY CODE 10AC57 ATQTD /D/ 09MATERIAL,BODY,VALVE VALVE BODY MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE VALVE BODY IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ATQUJ /D/X10CAPACITY,INPUT INPUT CAPACITY THE RATED PRESSURE THE UNIT CAN WITHSTAND ON INPUT. 2D AND 1B MODE REPLY22AG201AC20 ATQWD /D/ 17SURFACE TREATMENT,VALVE VALVE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE VALVE SURFACE. SELECT REPLY CODE 10AD09 ATQXD /D/ 19FINISH,SURFACE,VALVE VALVE SURFACE FINISH AN ADDITIONAL FINISHING PROCESS BY WHICH THE SURFACE OF THE VALVE IS ALTERED IN RESPECT TO POLISHING,GRINDING,AND THE LIKE. SELECT REPLY CODE 10AA41 ATQYJ 10PRESSURE RATING,WORKING,WOG,MAXIMUM MAXIMUM WOG WORKING PRESSURE RATING THE MAXIMUM WATER,OIL,OR GAS WORKING PRESSURE AT WHICH THE ITEM IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY12AG20 ATQZJ 10TEMP RATING,MAXIMUM MAXIMUM TEMP RATING THE MAXIMUM VALUE WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AS APPLIED TO THE OPERATION,OR LIMITATION OF OPERATION,OF AN ITEM. 1D AND 1B MODE REPLY11AB36 ATRAJ 04SIZE,PIPE,NOMINAL,VALVE VALVE NOMINAL PIPE SIZE THE NOMINAL VALUE USED TO DEFINE THE DIAMETER OF THE VALVE PIPE. 1D AND 1B MODE REPLY11AA05 ATRBD 07RENEWABILITY,RING,VALVE SEAT VALVE SEAT RING RENEWABILITY AN INDICATION OF WHETHER OR NOT THE VALVE SEAT RING/S/ IS RENEWABLE. SELECT REPLY CODE 10AM29 ATRCD 07RENEWABILITY,SEAT,VALVE DISK VALVE DISK SEAT RENEWABILITY AN INDICATION OF WHETHER OR NOT THE VALVE DISK SEAT(S) IS RENEWABLE. SELECT REPLY CODE 10AM29 ATRDL 16STYLE,CONNECTION,PIPE END PIPE END CONNECTION STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PIPE END CONNECTION. 1L MODE REPLY 0 ATRED /D/ 09MATERIAL,PIPE PIPE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PIPE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ATRFJ 04SIZE,PIPE,NOMINAL NOMINAL PIPE SIZE THE NOMINAL VALUE USED TO DEFINE THE DIAMETER OF THE PIPE. 1D AND 1B MODE REPLY11AA05 ATRGD /D/ 07VALVE,RELIEF,SAFETY SAFETY RELIEF VALVE AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES A SAFETY RELIEF VALVE. SELECT REPLY CODE 10AA49 ATRHJ 10PRESSURE RATING,FIXED FIXED PRESSURE RATING THE FIXED /NONADJUSTABLE/ PRESSURE RATING OF THE ITEM. 1D AND 1B MODE REPLY12AG20 ATRJD /D/ 09MATERIAL,LINE,MAIN MAIN LINE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MAIN LINE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ATRKL 16STYLE,CONNECTION,END,MAIN LINE MAIN LINE END CONNECTION STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE MAIN LINE END CONNECTION. 1L MODE REPLY 0 ATRLJ 04SIZE,PIPE,NOMINAL,MAIN LINE MAIN LINE NOMINAL PIPE SIZE THE NOMINAL VALUE USED TO DEFINE THE DIAMETER OF THE MAIN LINE PIPE. 1D AND 1B MODE REPLY11AA05 ATRMJ 04LENGTH,OVERALL,MAIN LINE MAIN LINE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE MAIN LINE. 2D AND 1B MODE REPLY21AA051AC20 ATRNJ /D/ 10PRESSURE RATING,STEAM,MAXIMUM MAXIMUM STEAM PRESSURE RATING THE MAXIMUM STEAM PRESSURE AT WHICH THE ITEM IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY12AG20 ATRPD 18TYPE,VALVE,BYPASS LINE BYPASS LINE VALVE TYPE INDICATES THE TYPE OF BYPASS LINE VALVE PROVIDED. SELECT REPLY CODE 10AL80 ATRQA 12QUANTITY,VALVE,BYPASS LINE BYPASS LINE VALVE QUANTITY THE NUMBER OF BYPASS LINE VALVES PROVIDED. 1A MODE REPLY 0 ATRRJ 10WEIGHT,MAXIMUM,COATED CLOTH COATED CLOTH MAXIMUM WEIGHT AN INDICATION OF THE MAXIMUM WEIGHT OF THE COATED CLOTH. 1D AND 1B MODE REPLY12AG69 ATRSJ 04DIAMETER FOR WHICH DESIGNED,ROLLER ROLLER DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ROLLER FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ATRTJ 04LENGTH FOR WHICH DESIGNED,ROLLER ROLLER LENGTH FOR WHICH DESIGNED A MEASUREMENT OF THE LONGEST DIMENSION OF THE ROLLER FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 ATRWJ 04LENGTH,OVERALL,BULK SLEEVING BULK SLEEVING OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BULK SLEEVING. 1D AND 1B MODE REPLY11AA05 ATRXJ 04WIDTH ACCOMMODATED,CARRIAGE CARRIAGE WIDTH ACCOMMODATED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CARRIAGE THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 ATRYA 19NUMBER,MODEL,LAUNCHER LAUNCHER MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE LAUNCHER. 1A MODE REPLY 0 ATRZD /D/ 18TYPE,CAP,END END CAP TYPE INDICATES THE TYPE OF END CAPS PROVIDED ON THE ITEM. SELECT REPLY CODE 10AK84 ATSAA 19NUMBER,MODEL,HEAD HEAD MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE HEAD. 1A MODE REPLY 0 ATSBD /D/ 07FUZE,NOSE NOSE FUZE AN INDICATION OF WHETHER OR NOT A NOSE FUZE IS INCLUDED. PLEASE USE MRC ABFF. SELECT REPLY CODE 10AA49 ATSCA 19NUMBER,MODEL,MOTOR MOTOR MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE MOTOR. 1A MODE REPLY 0 ATSDD /D/ 07FUZE,BASE BASE FUZE AN INDICATION OF WHETHER OR NOT A BASE FUZE IS INCLUDED. PLEASE USE MRC ABFF. SELECT REPLY CODE 10AA49 ATSEA /D/ 19NUMBER,MODEL,SUPPLEMENTARY CHARGE SUPPLEMENTARY CHARGE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE SUPPLEMENTARY CHARGE. 1A MODE REPLY 0 ATSFD 03DESIGNATION,SIZE,MOTOR MOTOR SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE MOTOR IS COMMERCIALLY KNOWN. SELECT REPLY CODE 10AF81 ATSGA 12QUANTITY,GRAIN,MOTOR PROPELLANT MOTOR PROPELLANT GRAIN QUANTITY THE NUMBER OF MOTOR PROPELLANT GRAINS INCLUDED. 1A MODE REPLY 0 ATSHD 09MATERIAL,PROPELLANT,MOTOR MOTOR PROPELLANT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MOTOR PROPELLANT IS FABRICATED. SELECT REPLY CODE 10AF45 ATSJA 19NUMBER,MODEL,MOTOR PROPELLANT GRAIN MOTOR PROPELLANT GRAIN MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE MOTOR PROPELLANT GRAIN. 1A MODE REPLY 0 ATSKJ 10WEIGHT,GRAIN,MOTOR PROPELLANT MOTOR PROPELLANT GRAIN WEIGHT THE TOTAL WEIGHT OF THE MOTOR PROPELLANT GRAINS. 1D AND 1B MODE REPLY12AG67 ATSLD /D/ 07ASSEMBLY,CABLE CABLE ASSEMBLY AN INDICATION OF WHETHER OR NOT A CABLE ASSEMBLY IS INCLUDED. PLEASE USE MRC ABFF. SELECT REPLY CODE 10AA49 ATSMD 07ASSEMBLY,HEAD TO MOTOR HEAD TO MOTOR ASSEMBLY AN INDICATION OF WHETHER OR NOT THE HEAD IS ASSEMBLED TO THE MOTOR. SELECT REPLY CODE 10AM27 ATSNA 12QUANTITY,ROCKET,LAUNCHER LAUNCHER ROCKET QUANTITY THE NUMBER OF ROCKETS THE LAUNCHER IS DESIGNED TO CONTAIN. 1A MODE REPLY 0 ATSPA 19NUMBER,MODEL,CABLE ASSEMBLY CABLE ASSEMBLY MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE CABLE ASSEMBLY. 1A MODE REPLY 0 ATSQD /D/ 07ROPE,TIE TIE ROPE AN INDICATION OF WHETHER OR NOT A TIE ROPE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 ATSRD /D/ 07DEVICE,COLLECTING,RAINWATER RAINWATER COLLECTING DEVICE AN INDICATION OF WHETHER OR NOT A RAINWATER COLLECTING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 ATSSD /D/ 07STREAMER,WARNING WARNING STREAMER AN INDICATION OF WHETHER OR NOT A WARNING STREAMER IS INCLUDED. PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 ATSTA 19NUMBER FOR WHICH DESIGNED,IDENTIFICATION,AIRCRAFT AIRCRAFT IDENTIFICATION NUMBER FOR WHICH DESIGNED AN INDICATION OF THE AIRCRAFT IDENTIFICATION NUMBER FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 ATSXD /D/ 07TUBE,DEHYDRATOR DEHYDRATOR TUBE AN INDICATION OF WHETHER OR NOT A DEHYDRATOR TUBE IS INCLUDED. SELECT REPLY CODE 10AA49 ATSYA 12QUANTITY,WINDOW WINDOW QUANTITY THE NUMBER OF WINDOWS PROVIDED. 1A MODE REPLY 0 ATSZA 12QUANTITY,DOOR DOOR QUANTITY THE NUMBER OF DOORS PROVIDED. 1A MODE REPLY 0 ATTAA 12QUANTITY,CURTAIN,DETACHABLE DETACHABLE CURTAIN QUANTITY THE NUMBER OF DETACHABLE CURTAINS PROVIDED. 1A MODE REPLY 0 ATTBJ 04HEIGHT,OVERALL,CURTAIN CURTAIN OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE CURTAIN. 2D AND 1B MODE REPLY21AA051AC20 ATTCJ 04WIDTH,OVERALL,CURTAIN CURTAIN OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CURTAIN,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 ATTDA 12QUANTITY,WINDOW,CURTAIN CURTAIN WINDOW QUANTITY THE NUMBER OF CURTAIN WINDOWS PROVIDED. 1A MODE REPLY 0 ATTEJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,END,STUD STUD END THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE FOR THE STUD END. 1D AND 1A MODE REPLY12AH06 ATTFD /D/ 07LINING,FRICTION FRICTION LINING AN INDICATION OF WHETHER OR NOT A FRICTION LINING IS INCLUDED. SELECT REPLY CODE 10AA49 ATTGG 19WEAPON FOR WHICH DESIGNED WEAPON FOR WHICH DESIGNED AN INDICATION OF THE WEAPON(S) WITH WHICH THE ITEM IS DESIGNED TO FUNCTION. FULL TEXT WRITE-IN 0 ATTHD 01COLOR,BAG BAG COLOR THE HUE OR TINT OF THE BAG. SELECT REPLY CODE 10AD06 ATTJD /D/ 07PRIMER,PACKED PACKED PRIMER AN INDICATION OF WHETHER OR NOT A PACKED PRIMER IS INCLUDED. SELECT REPLY CODE 10AA49 ATTKD /D/ 07FEATURE,FLASHLESS FLASHLESS FEATURE AN INDICATION OF WHETHER OR NOT A FLASHLESS FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 ATTLD 19FEATURE,DURABILITY DURABILITY FEATURE AN INDICATION OF THE DURABILITY FEATURE. SELECT REPLY CODE 10AH22 ATTMD 07TOXICITY TOXICITY AN INDICATION OF WHETHER OR NOT THE ITEM IS TOXIC. SELECT REPLY CODE 10AM28 ATTND 09MATERIAL,CHARGE,FLASH FLASH CHARGE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FLASH CHARGE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AF45 ATTPB 10CANDLEPOWER RATING IN MILLIONS,NOMINAL,FLASH FLASH NOMINAL CANDLEPOWER RATING IN MILLIONS A MEASUREMENT OF LUMINOUS INTENSITY OF THE ITEM,EXPRESSED IN CANDLEPOWER MILLIONS. 1B MODE REPLY 0 ATTQD /D/ 07PRIMER,INTEGRAL INTEGRAL PRIMER AN INDICATION OF WHETHER OR NOT AN INTEGRAL PRIMER IS INCLUDED. SELECT REPLY CODE 10AA49 ATTRD /D/ 07AMMUNITION,TRAINING TRAINING AMMUNITION AN INDICATION OF WHETHER OR NOT TRAINING AMMUNITION IS INCLUDED. SELECT REPLY CODE 10AA49 ATTSG 19AMMUNITION FOR WHICH DESIGNED AMMUNITION FOR WHICH DESIGNED AN INDICATION OF THE AMMUNITION WITH WHICH THE ITEM IS DESIGNED TO FUNCTION. FULL TEXT WRITE-IN 0 ATTTA 19NUMBER,MODEL,TRAINING AMMUNITION TRAINING AMMUNITION MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE TRAINING AMMUNITION. 1A MODE REPLY 0 ATTWD 18TYPE,FILLER,EXPLOSIVE EXPLOSIVE FILLER TYPE INDICATES THE TYPE OF EXPLOSIVE FILLER PROVIDED. SELECT REPLY CODE 10AF45 ATTXA 19NUMBER,MODEL,DESTRUCTOR DESTRUCTOR MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE DESTRUCTOR. 1A MODE REPLY 0 ATTYD 03DESIGNATION,RATING,POWER CHARGE POWER CHARGE RATING DESIGNATION A DESIGNATION INDICATING THE RATED POWER CHARGE OF THE ITEM. SELECT REPLY CODE 10AM30 ATTZD 01COLOR,WAD WAD COLOR THE HUE OR TINT OF THE WAD. SELECT REPLY CODE 10AD06 ATWAA 19NUMBER FOR WHICH DESIGNED,MODEL,DUMMY CARTRIDGE DUMMY CARTRIDGE MODEL NUMBER FOR WHICH DESIGNED THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE DUMMY CARTRIDGE FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 ATWBJ 04SIZE FOR WHICH DESIGNED,CARTRIDGE,DUMMY DUMMY CARTRIDGE SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE DUMMY CARTRIDGE FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AF47 ATWCD /D/ 07PELLET PELLET AN INDICATION OF WHETHER OR NOT A PELLET(S) IS INCLUDED. SELECT REPLY CODE 10AA49 ATWDJ /D/ 04DISTANCE AND LOCATION,FLANGE TO FLANGE,DRUM DRUM FLANGE TO FLANGE DISTANCE AND LOCATION THE DISTANCE BETWEEN FLANGES ON THE DRUM,AND THE LOCATION ON THE ITEM. 3D AND 1B MODE REPLY31AA051AC203AJ91 ATWEJ 04DIAMETER AND LOCATION,DRUM DRUM DIAMETER AND LOCATION THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DRUM,AND TERMINATES AT THE CIRCUMFERENCE,AND ITS LOCATION ON THE ITEM. 3D AND 1B MODE REPLY31AA051AC203AJ91 ATWFJ /D/ 04DIAMETER AND LOCATION,FLANGE,DRUM DRUM FLANGE DIAMETER AND LOCATION THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DRUM FLANGE,AND TERMINATES AT THE CIRCUMFERENCE,AND ITS LOCATION ON THE ITEM. PLEASE USE MRC BXWF WITH ISAC CODING IN PLACE OF THIS DISCONTINUED MRC. 3D AND 1B MODE REPLY31AA051AC203AJ91 ATWGD 19POSITION,MOUNTING,CAPSTAN SPOOL CAPSTAN SPOOL MOUNTING POSITION AN INDICATION OF THE CAPSTAN SPOOL/S/ MOUNTING POSITION. SELECT REPLY CODE 10AC60 ATWHL 16STYLE,SPOOL,CAPSTAN CAPSTAN SPOOL STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CAPSTAN SPOOL. 1L MODE REPLY 0 ATWJD 02DESIGN,SURFACE,CAPSTAN SPOOL CAPSTAN SPOOL SURFACE DESIGN THE DESIGN OF THE CAPSTAN SPOOL SURFACE. SELECT REPLY CODE 10AK39 ATWKA 12QUANTITY,SPOOL,CAPSTAN CAPSTAN SPOOL QUANTITY THE NUMBER OF CAPSTAN SPOOLS INCLUDED. 1A MODE REPLY 0 ATWLA 12QUANTITY,WHEEL,WHELPED WHELPED WHEEL QUANTITY THE NUMBER OF WHELPED WHEELS INCLUDED. 1A MODE REPLY 0 ATWMA 12QUANTITY,WHELP WHELP QUANTITY THE NUMBER OF WHELPS INCLUDED. 1A MODE REPLY 0 ATWNJ /D/ 10LIMIT AT SELECTED SPEED AND DRUM LOCATION,LOAD LOAD LIMIT AT SELECTED SPEED AND DRUM LOCATION THE TOTAL LOAD THE ITEM IS CAPABLE OF MOVING AT SELECTED SPEEDS AND THE DRUM LOCATION. 3D AND 1B MODE REPLY32AG674AN503AJ91 ATWPJ 10TRAVEL RATE PER MINUTE TRAVEL RATE PER MINUTE THE DISTANCE THAT THE ITEM WILL MOVE PER MINUTE,PER SPECIFIC MEASUREMENT SCALE. 1D AND 1B MODE REPLY11AA05 ATWQA 12QUANTITY,SPEED,REVERSE REVERSE SPEED QUANTITY THE NUMBER OF REVERSE SPEEDS PROVIDED. 1A MODE REPLY 0 ATWRD 11METHOD,ADVANTAGE,MECHANICAL MECHANICAL ADVANTAGE METHOD THE MEANS USED TO GAIN A MECHANICAL ADVANTAGE. SELECT REPLY CODE 10AC58 ATWSD 11METHOD,BRAKING BRAKING METHOD THE MEANS BY WHICH THE BRAKING ACTION IS APPLIED. SELECT REPLY CODE 10AK88 ATWTA 12QUANTITY,HOOK HOOK QUANTITY THE NUMBER OF HOOKS PROVIDED. 1A MODE REPLY 0 ATWWA 12QUANTITY PER HOOK,ELEMENT,LOAD LOAD ELEMENT QUANTITY PER HOOK THE NUMBER OF ELEMENTS PER HOOK,WHICH ARE LOAD BEARING. 1A MODE REPLY 0 ATWXJ 04DISTANCE BETWEEN LOAD ELEMENTS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN LOAD ELEMENTS THE DISTANCE BETWEEN THE CENTERS OF THE LOAD ELEMENTS. 2D AND 1B MODE REPLY21AA051AC20 ATWYD 11METHOD,CONSTRUCTION,ASSEMBLY ASSEMBLY CONSTRUCTION METHOD THE MEANS IN WHICH THE COMPONENTS OF AN ASSEMBLY ARE MOUNTED ON EACH OTHER OR ON A COMMON MOUNTING. SELECT REPLY CODE 10AM36 ATWZD 19ADVANTAGE,MECHANICAL,GEAR GEAR MECHANICAL ADVANTAGE THE APPROXIMATE MECHANICAL ADVANTAGE OR POWER/STRENGTH GAINED THROUGH THE USE OF TWO OR MORE GEARS. SELECT REPLY CODE 10AL19 ATXAD 18TYPE,CLUTCH CLUTCH TYPE INDICATES THE TYPE OF CLUTCH PROVIDED. SELECT REPLY CODE 10AG25 ATXBD 11METHOD,WINDING,RETRIEVAL RETRIEVAL WINDING METHOD THE MEANS BY WHICH AN ITEM IS RETRIEVED. SELECT REPLY CODE 10AL27 ATXCJ /D/A08LOCATION AND QUANTITY,HOUSING,GEAR GEAR HOUSING LOCATION AND QUANTITY INDICATES THE GEAR HOUSING LOCATION ON THE ITEM AND THE NUMBER OF EACH. 1D AND 1A MODE REPLY13AJ91 ATXDD 08LOCATION,END,DRIVE DRIVE END LOCATION INDICATES THE LOCATION OF THE DRIVE END/S/ ON THE ITEM. SELECT REPLY CODE 10AJ91 ATXED 19POSITION,MOUNTING,SHAFT SHAFT MOUNTING POSITION AN INDICATION OF THE SHAFT MOUNTING POSITION. SELECT REPLY CODE 10AC60 ATXFD /D/ 09MATERIAL,BODY,BYPASS LINE VALVE BYPASS LINE VALVE BODY MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BYPASS LINE VALVE BODY IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ATXGD /D/ 17SURFACE TREATMENT,VALVE,BYPASS LINE BYPASS LINE VALVE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE BYPASS LINE VALVE SURFACE. SELECT REPLY CODE 10AD09 ATXHD /D/ 19FINISH,SURFACE,BYPASS LINE VALVE BYPASS LINE VALVE SURFACE FINISH AN ADDITIONAL FINISHING PROCESS BY WHICH THE SURFACE OF THE BYPASS LINE VALVE IS ALTERED IN RESPECT TO POLISHING,GRINDING,AND THE LIKE. SELECT REPLY CODE 10AA41 ATXJJ 04SIZE,PIPE,NOMINAL,BYPASS LINE VALVE BYPASS LINE VALVE NOMINAL PIPE SIZE THE NOMINAL VALUE USED TO DEFINE THE DIAMETER OF THE BYPASS LINE VALVE PIPE. 1D AND 1B MODE REPLY11AA05 ATXKJ /D/ 10PRESSURE RATING,WORKING,MAXIMUM WOG,BYPASS LINE VALVE BYPASS LINE VALVE MAXIMUM WOG WORKING PRESSURE RATING THE MAXIMUM WATER,OIL,OR GAS WORKING PRESSURE AT WHICH THE BYPASS LINE VALVE IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY12AG20 ATXLJ /D/ 10PRESSURE RATING,STEAM,MAXIMUM,BYPASS LINE VALVE BYPASS LINE VALVE MAXIMUM STEAM PRESSURE RATING THE MAXIMUM STEAM PRESSURE AT WHICH THE BYPASS LINE VALVE IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY12AG20 ATXMJ /D/ 10TEMP RATING,MAXIMUM,BYPASS LINE VALVE BYPASS LINE VALVE MAXIMUM TEMP RATING THE MAXIMUM VALUE WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AS APPLIED TO THE OPERATION,OR LIMITATION OF OPERATION OF THE BYPASS LINE VALVE. 1D AND 1B MODE REPLY11AB36 ATXNJ /D/T10RANGE,REDUCING,PRESSURE PRESSURE REDUCING RANGE THE MINIMUM AND MAXIMUM LIMITS OF THE PRESSURE REDUCING CAPABILITY OF THE ITEM. 1D AND 1F MODE REPLY12AG20 ATXPJ 10CAPACITY,CUBIC,DIPPER DIPPER CUBIC CAPACITY A MEASUREMENT OF THE INTERNAL CAPACITY OF THE DIPPER TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE DEPTH AND RENDERED IN CUBIC UNITS. 1D AND 1B MODE REPLY11AD42 ATXQJ 10CAPACITY,LIFTING,BASIC UNIT BASIC UNIT LIFTING CAPACITY THE WEIGHT THAT THE BASIC UNIT IS DESIGNED TO LIFT. 2D AND 1B MODE REPLY22AG671AC20 ATXRJ 10CAPACITY,CUBIC,BASIC UNIT BASIC UNIT CUBIC CAPACITY A MEASUREMENT OF THE INTERNAL CAPACITY OF THE BASIC UNIT TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE DEPTH AND RENDERED IN CUBIC UNITS. 1D AND 1B MODE REPLY11AD42 ATXSJ 04LENGTH,RETRACTED RETRACTED LENGTH THE MEASUREMENT OF THE LONGEST DIMENSION OF THE ITEM WHEN RETRACTED. 2D AND 1B MODE REPLY21AA051AC20 ATXTA /D/ 12QUANTITY,DECK DECK QUANTITY THE NUMBER OF DECKS PROVIDED. 1A MODE REPLY 0 ATXWG /D/ 10RANGE,ATTENUATION ATTENUATION RANGE THE ENERGY REDUCTION RANGE OF THE ITEM. FULL TEXT WRITE-IN 0 ATXXD 18TYPE,STOPPER,RUBBER RUBBER STOPPER TYPE INDICATES THE TYPE OF RUBBER STOPPER. SELECT REPLY CODE 10AC57 ATXYD /D/ 07STEP,OPEN OPEN STEP AN INDICATION OF WHETHER OR NOT AN OPEN STEP IS INCLUDED. SELECT REPLY CODE 10AA49 ATXZA 19NUMBER,TAPER,US DEPARTMENT OF COMMERCE US DEPARTMENT OF COMMERCE TAPER NUMBER THE NUMBER ASSIGNED BY THE US DEPARTMENT OF COMMERCE TO DESIGNATE THE TAPER SIZE OF AN ITEM. 1A MODE REPLY 0 ATYAD /D/ 07TAPER,STANDARD STANDARD TAPER AN INDICATION OF WHETHER OR NOT A STANDARD TAPER IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 ATYBD /D/ 18TYPE,STEP,LAST LAST STEP TYPE INDICATES THE TYPE OF LAST STEP PROVIDED. SELECT REPLY CODE 10AF63 ATYCD 19SIZE SIZE AN INDICATION OF THE SIZE OF THE ITEM. SELECT REPLY CODE 10AF81 ATYDJ 04DIAMETER FOR WHICH DESIGNED,INSIDE,OPENING OPENING INSIDE DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OPENING FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ATYED /D/ 07ACTION,DETENT DETENT ACTION AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH DETENT ACTION. SELECT REPLY CODE 10AB22 ATYFA 12QUANTITY,HOLE,THROUGH THROUGH HOLE QUANTITY THE NUMBER OF THROUGH HOLES PROVIDED. 1A MODE REPLY 0 ATYGJ 10REQUIREMENT RATING,POWER POWER REQUIREMENT RATING THE POWER REQUIRED TO START AND OPERATE THE ITEM AT RATED CAPACITY. 1D AND 1B MODE REPLY11AC33 ATYHD 02DESIGN,SURFACE,DRUM DRUM SURFACE DESIGN THE DESIGN ON THE DRUM SURFACE. SELECT REPLY CODE 10AA41 ATYJD 11METHOD,CONNECTION,ELECTRICAL ELECTRICAL CONNECTION METHOD THE MEANS USED FOR ELECTRICAL CONNECTION. SELECT REPLY CODE 10AD62 ATYKJ 10RESISTANCE,ELECTRICAL,COMBINED COMBINED ELECTRICAL RESISTANCE A MEASURE OF THE OPPOSITION TO THE FLOW OF DIRECT OR ALTERNATING CURRENT PROVIDED BY THE COMBINED ITEMS. 1D AND 1B MODE REPLY11AA57 ATYLF T10TOLERANCE IN PERCENT,RESISTANCE,COMBINED COMBINED RESISTANCE TOLERANCE IN PERCENT THE LIMITS OF PERMISSIBLE VARIATION IN THE ELECTRICAL RESISTANCE VALUE OF THE COMBINED ITEMS FROM THE RATED VALUE,EXPRESSED IN PERCENT. 1F MODE REPLY 0 ATYMD 19RELATIONSHIP,COMPONENT COMPONENT RELATIONSHIP THE CRITERIA DETERMINING THE FUNCTIONAL RELATIONSHIP OF THE COMPONENTS. SELECT REPLY CODE 10AM31 ATYNF T10TOLERANCE IN PERCENT,RESISTANCE,RESPECTIVE RESPECTIVE RESISTANCE TOLERANCE IN PERCENT THE LIMITS OF PERMISSIBLE VARIATION BETWEEN THE ELECTRICAL RESISTANCE VALUES OF THE MATCHED ITEMS,EXPRESSED IN PERCENT. 1F MODE REPLY 0 ATYPH /D/ 18TYPE AND LOCATION,END END TYPE AND LOCATION INDICATES THE END TYPE AND ITS LOCATION ON THE ITEM. 2D MODE REPLY 23AK843AJ91 ATYQG 10RESISTANCE RATING AT SPECIFIED VOLTAGE RESISTANCE RATING AT SPECIFIED VOLTAGE A MEASUREMENT OF THE OPPOSITION TO THE FLOW OF ELECTRICAL CURRENT AT A SPECIFIC VOLTAGE. FULL TEXT WRITE-IN 0 ATYRB /D/ 10COEFFICIENT PER DEG CELSIUS,EXPANSION,LINEAR LINEAR EXPANSION COEFFICIENT PER DEG CELSIUS THE CONSTANT THAT REPRESENTS THE CHANGE IN LINEAR EXPANSION CAUSED BY A CHANGE IN TEMPERATURE,PER DEGREES CELSIUS. 1B MODE REPLY 0 ATYSF T10RANGE IN DEG CELSIUS,TEMP,LINEAR EXPANSION COEFFICIENT LINEAR EXPANSION COEFFICIENT TEMP RANGE IN DEG CELSIUS THE MINIMUM AND MAXIMUM TEMPERATURES TO WHICH THE LINEAR EXPANSION COEFFICIENT APPLIES,EXPRESSED IN DEGREES CELSIUS. 1F MODE REPLY 0 ATYTJ 10TEMP RATING,RESISTANCE RESISTANCE TEMP RATING THE TEMPERATURE/S/ AT WHICH RESISTANCE HAS BEEN ESTABLISHED. 2D AND 1B MODE REPLY21AB361AC20 ATYWB 10PERCENTAGE,SILICA SILICA PERCENTAGE THE SILICA CONTENT PERCENTAGE OF THE ITEM. 1B MODE REPLY 0 ATYXJ 10CAPACITY RATING CAPACITY RATING THE RATED CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 ATYYJ 10VOLTAGE RATING,WORKING WORKING VOLTAGE RATING THE MAXIMUM SUSTAINED VOLTAGE THAT CAN SAFELY BE APPLIED TO AN ELECTRIC DEVICE WITHOUT RISKING THE POSSIBILITY OF A BREAKDOWN. 1D AND 1B MODE REPLY11AB63 ATZAA 12QUANTITY,CUP CUP QUANTITY THE NUMBER OF CUPS PROVIDED. 1A MODE REPLY 0 ATZBJ 04DIAMETER,INSIDE,OPEN END OPEN END INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OPEN END,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ATZCJ 04DIAMETER,OUTSIDE,OPEN END OPEN END OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OPEN END,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ATZDJ 04DIAMETER,OUTSIDE,BOTTOM END BOTTOM END OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOTTOM END,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 ATZED /D/ 09MATERIAL,PLUNGER PLUNGER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH A PLUNGER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 ATZFD /D/ 07BEVEL,END,LOWER,PLUNGER PLUNGER LOWER END BEVEL AN INDICATION OF WHETHER OR NOT A PLUNGER LOWER END BEVEL IS INCLUDED. SELECT REPLY CODE 10AA49 ATZGB 04ANGLE IN DEG,BEVEL BEVEL ANGLE IN DEG THE ANGLE OF THE BEVEL,EXPRESSED IN DEGREES. 1B MODE REPLY 0 ATZHD /D/ 07PIN,LOCATING,PLUNGER CORRECT ALIGNMENT PLUNGER CORRECT ALIGNMENT LOCATING PIN AN INDICATION OF WHETHER OR NOT A PLUNGER CORRECT ALIGNMENT LOCATING PIN/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 ATZJD /D/ 07ATTACHMENT,MICRO MICRO ATTACHMENT AN INDICATION OF WHETHER OR NOT A MICRO ATTACHMENT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 ATZKA /D/ 12QUANTITY,CUP,MICRO MICRO CUP QUANTITY THE NUMBER OF MICRO CUPS PROVIDED. 1A MODE REPLY 0 ATZLJ /D/ 04LENGTH,OVERALL,CUP CUP OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CUP. 2D AND 1B MODE REPLY21AA051AC20 ATZMJ /D/ 10CAPACITY,CUP CUP CAPACITY THE AMOUNT OF LIQUID,GRANULES,AND THE LIKE THE CUP WILL HOLD. 1D AND 1B MODE REPLY11AD42 ATZNA /D/ 12QUANTITY,PLUNGER,MICRO MICRO PLUNGER QUANTITY THE NUMBER OF MICRO PLUNGERS PROVIDED. 1A MODE REPLY 0 ATZPJ /D/ 04LENGTH,OVERALL,PLUNGER PLUNGER OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH THE TERMINATED POINTS AT THE EXTREME ENDS OF THE PLUNGER. 2D AND 1B MODE REPLY21AA051AC20 ATZQB 10LUMINOSITY IN LUMENS,LAMP LAMP LUMINOSITY IN LUMENS THE MEASUREMENT OF LUMINOUS FLUX FOR WHICH THE LAMP IS RATED,EXPRESSED IN LUMENS. 1B MODE REPLY 0 ATZRD /D/ 07INSCRIPTION INSCRIPTION AN INDICATION OF WHETHER OR NOT AN INSCRIPTION IS INCLUDED. SELECT REPLY CODE 10AA49 ATZSG 19INSCRIPTION,LEGEND LEGEND INSCRIPTION THE INSCRIPTION AFFIXED TO OR STAMPED ON THE ITEM,EXCLUDING THE PART NUMBER. FULL TEXT WRITE-IN 0 ATZTJ 04DEPTH,VIEWING VIEWING DEPTH A MEASUREMENT BETWEEN SPECIFIED VIEWING POINTS ON AN ITEM,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 ATZWD /D/ 07CALIBRATION,VOLUME VOLUME CALIBRATION AN INDICATION OF WHETHER OR NOT A VOLUME CALIBRATION IS INCLUDED. SELECT REPLY CODE 10AA49 ATZXB 10CALIBRATION IN MILLILITERS,VOLUME VOLUME CALIBRATION IN MILLILITERS THE VOLUME CALIBRATION OF AN ITEM,EXPRESSED IN MILLILITERS. 1B MODE REPLY 0 ATZYD /D/ 07PROVISION,PLATE,REDUCTION REDUCTION PLATE PROVISION AN INDICATION OF WHETHER OR NOT A REDUCTION PLATE PROVISION IS INCLUDED. SELECT REPLY CODE 10AA49 ATZZJ /D/ 04DEPTH,VIEWING,EFFECTIVE,REDUCTION PLATE IN PLACE REDUCTION PLATE IN PLACE EFFECTIVE VIEWING DEPTH THE MEASUREMENT BETWEEN SPECIFIED VIEWING POINTS THAT IS EFFECTIVE WHEN THE REDUCTION PLATE IS IN PLACE,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AUTHA /D/ 19DOCUMENT,SOURCE,CLASSIFICATION,SECURITY SECURITY CLASSIFICATION SOURCE DOCUMENT A SPECIFICATION, DRAWING, STANDARD, INSTRUCTION OR A SIMILAR DOCUMENT THAT HAS A SOURCE WITHIN WHICH INDICATES A SECURITY CLASSIFICATION. 1A MODE REPLY 0 AVMFA 19MANUFACTURING CAGE AND PART/MODEL NUMBER,ADDITIVE ADDITIVE MANUFACTURING CAGE AND PART/MODEL NUMBER THE ADDITIVE MANUFACTURER'S FIVE-DIGIT CAGE DESIGNATION AND THE PART/MODEL NUMBER. 1A MODE REPLY 0 AWAAD /D/ 07PLATE,REDUCTION REDUCTION PLATE AN INDICATION OF WHETHER OR NOT A REDUCTION PLATE IS INCLUDED. SELECT REPLY CODE 10AA49 AWABA 12QUANTITY,BARREL BARREL QUANTITY THE NUMBER OF BARRELS PROVIDED. 1A MODE REPLY 0 AWACD /D/ 09MATERIAL,BARREL BARREL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BARREL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AWADD /D/ 09MATERIAL,PLUMMET PLUMMET MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PLUMMET IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AWAEA 12QUANTITY,FLOAT FLOAT QUANTITY THE NUMBER OF FLOATS PROVIDED. 1A MODE REPLY 0 AWAFF T10RANGE,GRAVITY,SPECIFIC SPECIFIC GRAVITY RANGE THE LIMITS OF SPECIFIC GRAVITY INDICATED BY THE ITEM. 1F MODE REPLY 0 AWAGJ 10INCREMENT,SMALLEST,SCALE SCALE SMALLEST INCREMENT THE SMALLEST VALUE BETWEEN THE MARKINGS ON A SCALE. 1D AND 1B MODE REPLY12AG67 AWAHJ 10ACCURACY RATING,SCALE SCALE ACCURACY RATING THE MINIMUM AND MAXIMUM DEVIATION FROM THE EXACT READING OF THE SCALE. 1D AND 1B MODE REPLY12AB49 AWAJJ 10TEMP,CALIBRATION,SCALE SCALE CALIBRATION TEMP A VALUE WHICH EXPRESSES THE TEMPERATURE AT WHICH THE SCALE IS CALIBRATED. 1D AND 1B MODE REPLY11AB36 AWAKD /D/ 07THERMOMETER THERMOMETER AN INDICATION OF WHETHER OR NOT A THERMOMETER IS INCLUDED. SELECT REPLY CODE 10AA49 AWALD /D/ 07HOLDER,RECEPTACLE,SPECIMEN SPECIMEN RECEPTACLE HOLDER AN INDICATION OF WHETHER OR NOT A SPECIMEN RECEPTACLE HOLDER IS INCLUDED. SELECT REPLY CODE 10AA49 AWAMD 08LOCATION,HOLDER HOLDER LOCATION INDICATES THE LOCATION OF THE HOLDER ON THE ITEM. SELECT REPLY CODE 10AJ91 AWAND /D/ 07SCALE,CORRECTION CORRECTION SCALE AN INDICATION OF WHETHER OR NOT A CORRECTION SCALE IS INCLUDED. SELECT REPLY CODE 10AA49 AWAPD 08LOCATION,CHART,CORRECTION CORRECTION CHART LOCATION INDICATES THE LOCATION OF THE CORRECTION CHART. SELECT REPLY CODE 10AJ91 AWAQD /D/ 07CHART,CONVERSION CONVERSION CHART AN INDICATION OF WHETHER OR NOT A CONVERSION CHART IS INCLUDED. SELECT REPLY CODE 10AA49 AWARD 18TYPE,ATTENUATOR ATTENUATOR TYPE INDICATES THE TYPE OF ATTENUATOR PROVIDED. SELECT REPLY CODE 10AC01 AWASF T10TOLERANCE IN PERCENT,ATTENUATION ATTENUATION TOLERANCE IN PERCENT THE LIMITS OF PERMISSIBLE DEVIATION OF ATTENUATION OF AN ITEM FROM ITS RATED VALUE,EXPRESSED IN PERCENT. 1F MODE REPLY 0 AWATA 19NUMBER,MODEL,PLUG PLUG MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE PLUG. 1A MODE REPLY 0 AWAWD 18TYPE,PRIMER PRIMER TYPE INDICATES THE TYPE OF PRIMER PROVIDED. SELECT REPLY CODE 10AF48 AWAXJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,FACILITY,FLANGE CONNECTING FLANGE CONNECTING FACILITY THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE FLANGE CONNECTING FACILITY/IES/. 1D AND 1A MODE REPLY12AH06 AWAZJ /D/A13THREAD SIZE,FACILITY,MOUNTING MOUNTING FACILITY THREAD SIZE THE THREAD SERIES,THREAD MAJOR/MAXIMUM DIAMETER,AND THE NUMBER OF THREADS PER MEASUREMENT SCALE OF THE MOUNTING FACILITY. 1D AND 1A MODE REPLY12AH06 AWBAD /D/ 07FAIRING FAIRING AN INDICATION OF WHETHER OR NOT A FAIRING/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 AWBBD /D/ 07LAUNCHER,EXPENDABLE EXPENDABLE LAUNCHER AN INDICATION OF WHETHER OR NOT AN EXPENDABLE LAUNCHER IS PROVIDED. PLEASE USE MRC ABFF. SELECT REPLY CODE 10AB22 AWBCA 19NUMBER,MODEL,EXPENDABLE LAUNCHER EXPENDABLE LAUNCHER MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE EXPENDABLE LAUNCHER. 1A MODE REPLY 0 AWBDD /D/ 07INTERVALOMETER INTERVALOMETER AN INDICATION OF WHETHER OR NOT AN INTERVALOMETER IS INCLUDED. SELECT REPLY CODE 10AA49 AWBED /D/ 07INHIBITOR,PROPELLANT PROPELLANT INHIBITOR AN INDICATION OF WHETHER OR NOT A PROPELLANT INHIBITOR IS INCLUDED. SELECT REPLY CODE 10AA49 AWBFD /D/ 07IGNITER IGNITER AN INDICATION OF WHETHER OR NOT AN IGNITER IS INCLUDED. SELECT REPLY CODE 10AA49 AWBGD 07INSTALLATION,IGNITER IGNITER INSTALLATION AN INDICATION OF WHETHER OR NOT THE IGNITER IS INSTALLED. SELECT REPLY CODE 10AL24 AWBHD 18TYPE,ACCOMMODATION,PROPELLANT PROPELLANT ACCOMMODATION TYPE INDICATES THE TYPE OF PROPELLANT THAT THE ITEM WILL ACCOMMODATE. SELECT REPLY CODE 10AM33 AWBJA 19NUMBER,MODEL,IGNITER IGNITER MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE IGNITER. 1A MODE REPLY 0 AWBKD 18TYPE,CONNECTOR,CABLE ASSEMBLY CABLE ASSEMBLY CONNECTOR TYPE INDICATES THE TYPE OF CABLE ASSEMBLY CONNECTOR PROVIDED. SELECT REPLY CODE 10AJ57 AWBLB 10TIME IN SECONDS,BURNING,NOMINAL NOMINAL BURNING TIME IN SECONDS THE NOMINAL PERIOD OF BURNING TIME,EXPRESSED IN SECONDS. 1B MODE REPLY 0 AWBMJ 10THRUST,NOMINAL NOMINAL THRUST THE NOMINAL FORCE OF ENERGY EXPENDED. 1D AND 1B MODE REPLY12AG67 AWBNJ 04DIAMETER,OUTSIDE,STRAIGHT SECTION STRAIGHT SECTION OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE STRAIGHT SECTION,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AWBPB 04ANGLE IN DEG,CANT,NOZZLE NOZZLE CANT ANGLE IN DEG THE CANT ANGLE OF THE NOZZLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AWBQD /D/ 07ROD,RESONANCE RESONANCE ROD AN INDICATION OF WHETHER OR NOT A RESONANCE ROD IS INCLUDED. SELECT REPLY CODE 10AA49 AWBRD 11METHOD,STABILIZATION,INTEGRAL INTEGRAL STABILIZATION METHOD THE INTEGRAL MEANS UTILIZED TO STABILIZE THE ITEM. SELECT REPLY CODE 10AM34 AWBSD 11METHOD,CONTROL,INTEGRAL THRUST DIRECTION INTEGRAL THRUST DIRECTION CONTROL METHOD THE INTEGRAL MEANS UTILIZED TO CONTROL THE DIRECTION OF THRUST. SELECT REPLY CODE 10AL28 AWBTG /D/ 19LAUNCHER FOR WHICH DESIGNED,SPECIFIC SPECIFIC LAUNCHER FOR WHICH DESIGNED INDICATES THE SPECIFIC LAUNCHER FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 AWBWD /D/ 07GRANULATION,DUAL DUAL GRANULATION AN INDICATION OF WHETHER OR NOT DUAL GRANULATION IS INCLUDED. SELECT REPLY CODE 10AA49 AWBXD 02DESIGN,CHARGE,SIMULATED SIMULATED CHARGE DESIGN THE DESIGN OF THE SIMULATED CHARGE. SELECT REPLY CODE 10AJ64 AWBYD 09MATERIAL,CHARGE CHARGE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CHARGE IS FABRICATED. SELECT REPLY CODE 10AF45 AWBZD /D/ 07FEATURE,RECORDING RECORDING FEATURE AN INDICATION OF WHETHER OR NOT A RECORDING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AWCAJ 10WEIGHT,BALLAST BALLAST WEIGHT THE WEIGHT OF THE BALLAST. 1D AND 1B MODE REPLY12AG67 AWCBA 19NUMBER,MODEL,AUXILIARY DETONATOR AUXILIARY DETONATOR MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE AUXILIARY DETONATOR. 1A MODE REPLY 0 AWCCD /D/ 07BAND,LUG LUG BAND AN INDICATION OF WHETHER OR NOT A LUG BAND IS INCLUDED. SELECT REPLY CODE 10AA49 AWCDD 19WATER FOR WHICH DESIGNED WATER FOR WHICH DESIGNED THE TYPE OF WATER WITH WHICH THE ITEM IS DESIGNED TO BE USED. SELECT REPLY CODE 10AB75 AWCEB 10WEIGHT IN GRAMS,MATERIAL,CHARGE CHARGE MATERIAL WEIGHT IN GRAMS THE WEIGHT OF THE CHARGE MATERIAL,EXPRESSED IN GRAMS. 1B MODE REPLY 0 AWCFA 12QUANTITY,SQUIB SQUIB QUANTITY THE NUMBER OF SQUIBS PROVIDED. 1A MODE REPLY 0 AWCGA 19NUMBER,MODEL,SQUIB SQUIB MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE SQUIB. 1A MODE REPLY 0 AWCHJ 04LENGTH,LEAD,ELECTRICAL ELECTRICAL LEAD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ELECTRICAL LEAD,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AWCJA 19NUMBER FOR WHICH DESIGNED,MODEL,ROCKET MOTOR ROCKET MOTOR MODEL NUMBER FOR WHICH DESIGNED THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE ROCKET MOTOR FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 AWCKD 08LOCATION,OPERATING,REFRIGERANT REFRIGERANT OPERATING LOCATION INDICATES THE OPERATING LOCATION OF THE REFRIGERANT. SELECT REPLY CODE 10AJ91 AWCLD /D/ 07FEATURE,DELAY,TIME TIME DELAY FEATURE AN INDICATION OF WHETHER OR NOT A TIME DELAY FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AWCMJ 10CAPACITY,STORAGE,WATER WATER STORAGE CAPACITY THE WATER STORAGE CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 AWCNJ 10CAPACITANCE VALUE,COMBINED COMBINED CAPACITANCE VALUE THE RELATIVE LEVEL OF THE QUANTITY OF ELECTRIC CHARGE AT A GIVEN POTENTIAL WHICH THE COMBINED ITEMS ARE CAPABLE OF RECEIVING AND STORING. 1D AND 1B MODE REPLY11AC77 AWCPD 18TYPE,LABEL LABEL TYPE INDICATES THE TYPE OF LABEL ON THE ITEM. SELECT REPLY CODE 10AM32 AWCRF T10TOLERANCE IN PERCENT,CAPACITANCE,COMBINED COMBINED CAPACITANCE TOLERANCE IN PERCENT THE LIMITS OF PERMISSIBLE VARIATION IN THE CAPACITANCE VALUE OF THE COMBINED ITEM FROM THE RATED VALUE,EXPRESSED IN PERCENT. 1F MODE REPLY 0 AWCSF T10TOLERANCE IN PERCENT,CAPACITANCE,RESPECTIVE RESPECTIVE CAPACITANCE TOLERANCE IN PERCENT THE LIMITS OF PERMISSIBLE VARIATION BETWEEN THE CAPACITANCE VALUES OF THE MATCHED ITEMS,EXPRESSED IN PERCENT. 1F MODE REPLY 0 AWCTD 18TYPE,MOUTH MOUTH TYPE INDICATES THE TYPE OF MOUTH PROVIDED. SELECT REPLY CODE 10AM35 AWCWG 04SIZE FOR WHICH DESIGNED,CLOSURE CLOSURE SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE CLOSURE FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 AWCXD 18TYPE,CLOSURE CLOSURE TYPE INDICATES THE TYPE OF CLOSURE PROVIDED. SELECT REPLY CODE 10AM35 AWCYD /D/ 07BULB,CLOSURE CLOSURE BULB AN INDICATION OF WHETHER OR NOT A CLOSURE BULB IS INCLUDED. SELECT REPLY CODE 10AA49 AWCZD /D/ 09MATERIAL,STOPPER STOPPER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE STOPPER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AWDAD /D/ 09MATERIAL,APPLICATOR APPLICATOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE APPLICATOR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AWDBG /D/ 19SPEC/STD,MATERIAL,APPLICATOR APPLICATOR MATERIAL SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE APPLICATOR MATERIAL. FULL TEXT WRITE-IN 0 AWDCA 03DESIGNATION,SIZE,STANDARD TAPER,EXTERNAL EXTERNAL STANDARD TAPER SIZE DESIGNATION THE NUMERIC DESIGNATION BY WHICH THE EXTERNAL STANDARD TAPER SIZE IS IDENTIFIED. 1A MODE REPLY 0 AWDDA /D/ 03DESIGNATION,SIZE,STANDARD TAPER,INTERNAL INTERNAL STANDARD TAPER SIZE DESIGNATION THE NUMERIC DESIGNATION BY WHICH THE INTERNAL STANDARD TAPER SIZE IS IDENTIFIED. 1A MODE REPLY 0 AWDED 18TYPE,CONNECTION,SIDE SIDE CONNECTION TYPE INDICATES THE TYPE OF SIDE CONNECTION PROVIDED. SELECT REPLY CODE 10AM35 AWDFA 03DESIGNATION,STOPPER,STANDARD RUBBER STANDARD RUBBER STOPPER DESIGNATION THE NUMERIC DESIGNATION BY WHICH THE RUBBER STOPPER IS IDENTIFIED. 1A MODE REPLY 0 AWDGA 03DESIGNATION,SIZE,STANDARD TAPER STANDARD TAPER SIZE DESIGNATION THE NUMERIC DESIGNATION BY WHICH THE STANDARD TAPER SIZE IS IDENTIFIED. 1A MODE REPLY 0 AWDHB 13THREAD SIZE IN INCHES,PIPE,STANDARD STANDARD PIPE THREAD SIZE IN INCHES THE DIAMETER OF THE PIPE THREADED TO NATIONAL PIPE THREAD STANDARDS,EXPRESSED IN INCHES. 1B MODE REPLY 0 AWDJA 12QUANTITY,HANDLE,CARRYING CARRYING HANDLE QUANTITY THE NUMBER OF CARRYING HANDLES PROVIDED. 1A MODE REPLY 0 AWDKD /D/ 07INLET,AIR,SEPARATE SEPARATE AIR INLET AN INDICATION OF WHETHER OR NOT A SEPARATE AIR INLET IS INCLUDED. SELECT REPLY CODE 10AA49 AWDLD /D/ 07CONNECTION BETWEEN OUTLET TUBE AND TAPERED TIP,HOSE,RUBBER RUBBER HOSE CONNECTION BETWEEN OUTLET TUBE AND TAPERED TIP AN INDICATION OF WHETHER OR NOT A RUBBER HOSE CONNECTION BETWEEN OUTLET TUBE AND TAPERED TIP IS INCLUDED. SELECT REPLY CODE 10AA49 AWDMD /D/ 07VALVE,RELEASE,FINGER FINGER RELEASE VALVE AN INDICATION OF WHETHER OR NOT A FINGER RELEASE VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 AWDNA 12QUANTITY,STOPPER STOPPER QUANTITY THE NUMBER OF STOPPERS PROVIDED. 1A MODE REPLY 0 AWDPJ 04THREAD DIAMETER THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AWDQJ 18TYPE AND SIZE FOR WHICH DESIGNED,CLOSURE CLOSURE TYPE AND SIZE FOR WHICH DESIGNED INDICATES THE TYPE AND SIZE OF THE CLOSURE FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA053AM35 AWDRD /D/ 07TAB,TEAR TEAR TAB AN INDICATION OF WHETHER OR NOT A TEAR TAB IS INCLUDED. SELECT REPLY CODE 10AA49 AWDSJ 04THICKNESS,LINER LINER THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A LINER,IN DISTINCTION FROM LENGTH OF WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AWDTD /D/ 07FEATURE,TRANSPARENT TRANSPARENT FEATURE AN INDICATION OF WHETHER OR NOT A TRANSPARENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AWDWB 10CAPACITY IN MILLILITERS CAPACITY IN MILLILITERS THE AMOUNT OF LIQUID,GRANULES,AND THE LIKE,THE ITEM WILL HOLD,EXPRESSED IN MILLILITERS. 1B MODE REPLY 0 AWDXD /D/ 07FEATURE,TRANSPORT,AIRBORNE AIRBORNE TRANSPORT FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES A FEATURE MAKING IT TRANSPORTABLE BY AIR. SELECT REPLY CODE 10AA49 AWDYD /D/ 07FEATURE,CALIBRATED CALIBRATED FEATURE AN INDICATION OF WHETHER OR NOT A CALIBRATED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AWDZB 10TEMP IN DEG CELSIUS,CALIBRATION CALIBRATION TEMP IN DEG CELSIUS THE NUMERIC VALUE INDICATING THE MEASUREMENT FOR THE CALIBRATION TEMPERATURE,EXPRESSED IN DEGREES CELSIUS. 1B MODE REPLY 0 AWEAD /D/ 07GRADUATIONS GRADUATIONS AN INDICATION OF WHETHER OR NOT GRADUATIONS ARE INCLUDED. SELECT REPLY CODE 10AA49 AWEBF /D/T10RANGE IN MILLILITERS,GRADUATION GRADUATION RANGE IN MILLILITERS THE MINIMUM AND MAXIMUM GRADUATIONS OF AN ITEM,EXPRESSED IN MILLILITERS. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1F MODE REPLY 0 AWECG 19INTERVAL,GRADUATION GRADUATION INTERVAL THE INTERVAL/S/ AS INDICATED BY THE MARKINGS ON THE ITEM. FULL TEXT WRITE-IN 0 AWEDG /D/ 19INTERVAL,GRADUATION,THERMOMETER THERMOMETER GRADUATION INTERVAL THE INTERVAL(S) AS INDICATED BY THE MARKINGS ON THE THERMOMETER. FULL TEXT WRITE-IN 0 AWEED 18TYPE,FITTING FITTING TYPE INDICATES THE TYPE OF FITTING PROVIDED. SELECT REPLY CODE 10AM35 AWEFA /D/ 03DESIGNATOR,SIZE,THERMOMETER STANDARD TAPER THERMOMETER STANDARD TAPER SIZE DESIGNATOR THE NUMERIC DESIGNATION BY WHICH THE STANDARD TAPER SIZE OF THE THERMOMETER IS IDENTIFIED. 1A MODE REPLY 0 AWEGD 18TYPE,FITTING,OPENING OPENING FITTING TYPE INDICATES THE TYPE OF FITTING USED ON THE OPENING. SELECT REPLY CODE 10AM35 AWEHD 11METHOD,MOUNTING,SUSPENSION SUSPENSION MOUNTING METHOD THE MEANS USED IN THE SUSPENSION MOUNTING OF AN ITEM. SELECT REPLY CODE 10AM39 AWEJL 16STYLE,SUSPENSION,TROLLEY TROLLEY SUSPENSION STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TROLLEY SUSPENSION. 1L MODE REPLY 0 AWEKD 18TYPE,TROLLEY TROLLEY TYPE INDICATES THE TYPE OF TROLLEY PROVIDED. SELECT REPLY CODE 10AC58 AWELJ 10SPEED,TRAVERSING,MAXIMUM MAXIMUM TRAVERSING SPEED THE MAXIMUM RATED TRAVERSING SPEED OF THE ITEM. 1D AND 1B MODE REPLY11AA22 AWEMA 12QUANTITY,TAP TAP QUANTITY THE NUMBER OF TAPS ON THE ITEM. 1A MODE REPLY 0 AWENB 10RESISTANCE BETWEEN TAPS IN OHMS,SECTION SECTION RESISTANCE BETWEEN TAPS IN OHMS THE OPPOSITION TO THE FLOW OF ELECTRIC CURRENT THROUGH EACH SECTION BETWEEN TAPS,EXPRESSED IN OHMS. 1B MODE REPLY 0 AWEPD /D/ 18TYPE FOR WHICH DESIGNED,CAPACITOR CAPACITOR TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF CAPACITOR WITH WHICH THE ITEM IS DESIGNED TO BE USED. SELECT REPLY CODE 10AA58 AWEQA 12QUANTITY PER SECTION,PLATE PLATE QUANTITY PER SECTION THE NUMBER OF PLATES IN EACH SECTION. 1A MODE REPLY 0 AWERB /D/ 10VOLTAGE IN VOLTS,THRESHOLD THRESHOLD VOLTAGE IN VOLTS THE MINIMUM ROOT MEAN SQUARE POTENTIAL AT WHICH REGULATION IS EFFECTIVE WITHIN SPECIFIC CURRENT LIMITS,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AWESA /D/ 18TYPE PER MIL-E-1,ENVELOPE ENVELOPE TYPE PER MIL-E-1 THE ENVELOPE TYPE PER MIL-E-1 INDICATING THE BASIC DESIGNATOR. 1A MODE REPLY 0 AWETD 18TYPE,BASE BASE TYPE INDICATES THE TYPE OF BASE FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AJ57 AWEWJ 04DISTANCE BETWEEN SUSPENSION HOOK AND LOAD BEARING SURFACE,RAISED POSITION RAISED POSITION DISTANCE BETWEEN SUSPENSION HOOK AND LOAD HOOK BEARING SURFACE THE DISTANCE MEASURED ALONG A VERTICAL LINE FROM THE SUSPENSION HOOK BEARING SURFACE TO THE LOAD HOOK BEARING SURFACE. 2D AND 1B MODE REPLY21AA051AC20 AWEXJ 04LENGTH,WINCH WINCH LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A WINCH,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AWEYJ 04LENGTH,FRAME,MOUNTING MOUNTING FRAME LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING FRAME,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AWEZJ 04WIDTH,FRAME,MOUNTING MOUNTING FRAME WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING FRAME,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AWFAD 03DESIGNATION,DRUM DRUM DESIGNATION A DESIGNATION BY WHICH THE DRUM IS IDENTIFIED. SELECT REPLY CODE 10AH21 AWFBJ /D/ 04DIAMETER AND LOCATION,LARGEST LARGEST DIAMETER AND LOCATION NONE. PLEASE USE MRC AGQA WITH ISAC CODING IN PLACE OF THIS DISCONTINUED MRC. 3D AND 1B MODE REPLY31AA051AC203AJ91 AWFCJ /D/ 04LENGTH AND LOCATION,OVERALL OVERALL LENGTH AND LOCATION NONE. PLEASE USE MRC ABTZ WITH ISAC IN PLACE OF THIS DISCONTINUED MRC. 3D AND 1B MODE REPLY31AA051AC203AJ91 AWFDJ /D/ 04DIAMETER AND LOCATION,SMALLEST SMALLEST DIAMETER AND LOCATION NONE. PLEASE USE MRC AYTY AND ISAC IN PLACE OF THIS DISCONTINUED MRC. 3D AND 1B MODE REPLY31AA051AC203AJ91 AWFED 19CONNECTION,PIN,RESISTIVE ELEMENT RESISTIVE ELEMENT PIN CONNECTION AN INDICATION OF THE PINS TO WHICH THE RESISTIVE ELEMENT IS CONNECTED. SELECT REPLY CODE 10AM37 AWFFJ 04HEIGHT,TRACK TRACK HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AWFGJ 04DISTANCE TO LOAD HOOK BEARING SURFACE IN FULLY RAISED POSITION,TRACK UNDERSIDE TRACK UNDERSIDE DISTANCE TO LOAD HOOK BEARING SURFACE IN FULLY RAISED POSITION NONE. 2D AND 1B MODE REPLY21AA051AC20 AWFHJ 04DISTANCE,CENTER TO CENTER,WHEEL WHEEL CENTER TO CENTER DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AWFJD 19CHARACTERISTIC,MOUNTING,CHAIN CHAIN MOUNTING CHARACTERISTIC AN INDICATION OF THE MOUNTING CHARACTERISTIC/S/ OF THE CHAIN/S/. SELECT REPLY CODE 10AG85 AWFKD 19CHARACTERISTIC,MOUNTING,GEAR GEAR MOUNTING CHARACTERISTIC AN INDICATION OF THE MOUNTING CHARACTERISTIC/S/ OF THE GEAR/S/. SELECT REPLY CODE 10AG85 AWFLD /D/ 18TYPE,FACE,CLUTCH CLUTCH FACE TYPE INDICATES THE TYPE OF CLUTCH FACE/S/ PROVIDED. SELECT REPLY CODE 10AG89 AWFMD 18TYPE,FACE,BRAKE BRAKE FACE TYPE INDICATES THE TYPE OF BRAKE FACE/S/ PROVIDED. SELECT REPLY CODE 10AG89 AWFNA 12QUANTITY,ROW,LINK LINK ROW QUANTITY THE NUMBER OF ROWS THAT COMPRISE THE WIDTH OF A LINK OR CHAIN ASSEMBLY. 1A MODE REPLY 0 AWFPJ /D/ 04LENGTH,PITCH PITCH LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE PITCH,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AWFQL 16STYLE,LINK,FIRST CHAIN FIRST CHAIN LINK STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FIRST CHAIN LINK. 1L MODE REPLY 0 AWFRL 16STYLE,LINK,SECOND CHAIN SECOND CHAIN LINK STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SECOND CHAIN LINK. 1L MODE REPLY 0 AWFSD /D/ 07SIMILARITY,STYLE,CHAIN LINK CHAIN LINK STYLE SIMILARITY AN INDICATION OF WHETHER OR NOT THE CHAIN LINK STYLES ARE IDENTICAL. SELECT REPLY CODE 10AA37 AWFTD /D/ 07LINK,OFFSET OFFSET LINK AN INDICATION OF WHETHER OR NOT AN OFFSET LINK IS INCLUDED. SELECT REPLY CODE 10AA49 AWFWD 11METHOD,FASTENING,PIN PIN FASTENING METHOD THE MEANS OF SECURING THE PIN(S). SELECT REPLY CODE 10AF69 AWFXJ 04WIDTH,PLATE,FIRST CHAIN LINK FIRST CHAIN LINK PLATE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AWFYJ 04WIDTH AT BUSHING END,PLATE,FIRST CHAIN LINK FIRST CHAIN LINK PLATE WIDTH AT BUSHING END NONE. 2D AND 1B MODE REPLY21AA051AC20 AWFZJ 04WIDTH AT PIN END,PLATE,FIRST CHAIN LINK FIRST CHAIN LINK PLATE WIDTH AT PIN END NONE. 2D AND 1B MODE REPLY21AA051AC20 AWGAJ 04THICKNESS,NOMINAL,FIRST CHAIN LINK PLATE FIRST CHAIN LINK PLATE NOMINAL THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 AWGBJ 04DIAMETER,NOMINAL,FIRST CHAIN LINK PIN FIRST CHAIN LINK PIN NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AWGCD 18TYPE,ORIFICE,CLOSURE CLOSURE ORIFICE TYPE INDICATES THE TYPE OF CLOSURE ORIFICE PROVIDED. SELECT REPLY CODE 10AG79 AWGDJ /D/ 04DIAMETER,OUTSIDE,FIRST END COUPLING FIRST END COUPLING OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FIRST END COUPLING,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AWGEA 12QUANTITY,PASS PASS QUANTITY THE NUMBER OF PASSES PROVIDED. 1A MODE REPLY 0 AWGFJ 10AREA,COOLING,EFFECTIVE EFFECTIVE COOLING AREA THE AMOUNT OF EFFECTIVE COOLING AREA. 1D AND 1B MODE REPLY11AC51 AWGGJ 10AREA,SURFACE,CONDENSING CONDENSING SURFACE AREA THE AMOUNT OF CONDENSING SURFACE AREA. 1D AND 1B MODE REPLY11AC51 AWGHD 18TYPE,TUBE TUBE TYPE INDICATES THE TYPE OF TUBE PROVIDED. SELECT REPLY CODE 10AA62 AWGJD /D/ 09MATERIAL,TUBE TUBE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TUBE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC CYGN IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AWGKJ 04LENGTH,EFFECTIVE,TUBE TUBE EFFECTIVE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A TUBE BETWEEN THE INSIDE FACES OF THE TUBE SHEETS,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AWGLD /D/ 07FIN,TUBE TUBE FIN AN INDICATION OF WHETHER OF NOT THE TUBE(S) IS PROVIDED WITH FINS. SELECT REPLY CODE 10AB22 AWGMJ /D/ 10PRESSURE,SYSTEM,MAXIMUM RATED MAXIMUM RATED SYSTEM PRESSURE THE MAXIMUM AMOUNT OF PRESSURE FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AB18 AWGNJ 04WIDTH,DRIVE DRIVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AWGPG 04SIZE,STOCK STOCK SIZE DESIGNATES THE RELATIVE OR PROPORTIONATE SIZE OF THE STOCK. FULL TEXT WRITE-IN 0 AWGQD /D/ 07COVERING,LEATHER LEATHER COVERING AN INDICATION OF WHETHER OR NOT A LEATHER COVERING IS INCLUDED. SELECT REPLY CODE 10AA49 AWGRD 19FORM,SIDE,STRAIGHT STRAIGHT SIDE FORM THE FORM OF THE STRAIGHT SIDE. SELECT REPLY CODE 10AM23 AWGTD 18TYPE FOR WHICH DESIGNED,SEWING SEWING TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF SEWING FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AH21 AWGWD 18TYPE,STITCH STITCH TYPE INDICATES THE TYPE OF STITCH PROVIDED. SELECT REPLY CODE 10AB87 AWGXD 02DESIGN,MECHANISM,FEED FEED MECHANISM DESIGN THE DESIGN OF THE FEED MECHANISM. SELECT REPLY CODE 10AM40 AWGYD 18TYPE,NEEDLE NEEDLE TYPE INDICATES THE TYPE OF NEEDLE PROVIDED. SELECT REPLY CODE 10AG89 AWGZJ 10GAGE,NEEDLE NEEDLE GAGE THE DISTANCE BETWEEN THE NEEDLES. 2D AND 1B MODE REPLY21AA051AC20 AWHAD /D/ 18TYPE,BED BED TYPE INDICATES THE TYPE OF BED PROVIDED. SELECT REPLY CODE 10AE98 AWHBD /D/ 07TOP,TABLE TABLE TOP AN INDICATION OF WHETHER OR NOT A TABLE TOP IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AWHCD /D/ 07DRAWER DRAWER AN INDICATION OF WHETHER OR NOT A DRAWER IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AWHDD /D/ 07FEATURE,USAGE,MOBILE FIELD MOBILE FIELD USAGE FEATURE AN INDICATION OF WHETHER OR NOT A MOBILE FIELD USAGE FEATURE IS PROVIDED. IF PROVIDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB22 AWHED /D/ 07STAND,TABLE TABLE STAND AN INDICATION OF WHETHER OR NOT A TABLE STAND IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AWHFD 02DESIGN,STAND STAND DESIGN THE DESIGN OF THE STAND. SELECT REPLY CODE 10AK54 AWHGD /D/ 07FEATURE,MOUNTING,PEDESTAL PEDESTAL MOUNTING FEATURE AN INDICATION OF WHETHER OR NOT A PEDESTAL MOUNTING FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AWHHD 11METHOD,GENERATION,ILLUMINATION COLOR ILLUMINATION COLOR GENERATION METHOD THE MEANS BY WHICH THE ILLUMINATED COLOR IS GENERATED. SELECT REPLY CODE 10AL21 AWHJG /D/ 19NAME,INDICATOR INDICATOR NAME THE NOMENCLATURE BY WHICH THE INDICATOR IS IDENTIFIED. FULL TEXT WRITE-IN 0 AWHKG /D/ 10RANGE,INDICATOR INDICATOR RANGE THE CAPABILITY OF THE INDICATOR TO REGISTER DATA. FULL TEXT WRITE-IN 0 AWHLD /D/ 07PEDESTAL PEDESTAL AN INDICATION OF WHETHER OR NOT A PEDESTAL IS PROVIDED. IF PROVIDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB22 AWHMD 07ADJUSTABILITY,PEDESTAL PEDESTAL ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE PEDESTAL IS ADJUSTABLE. SELECT REPLY CODE 10AB00 AWHNJ /D/ 04HEIGHT,ADJUSTABLE,PEDESTAL PEDESTAL ADJUSTABLE HEIGHT AN ADJUSTABLE MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE PEDESTAL,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AWHPD 04SIZE,HEAD HEAD SIZE AN INDICATION OF THE HEAD SIZE. SELECT REPLY CODE 10AF81 AWHQD /D/ 18TYPE,BOBBIN BOBBIN TYPE INDICATES THE BOBBIN TYPE. SELECT REPLY CODE 10AE98 AWHRD 18TYPE,MECHANISM,SEWING SEWING MECHANISM TYPE INDICATES THE TYPE OF SEWING MECHANISM PROVIDED. SELECT REPLY CODE 10AD55 AWHSD /D/ 07PARTS AND TOOLS,SPARE SPARE PARTS AND TOOLS AN INDICATION OF WHETHER OR NOT SPARE PARTS AND TOOLS ARE INCLUDED. SELECT REPLY CODE 10AA49 AWHTJ 04DIAMETER,INSIDE,RING RING INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR RING,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AWHWJ A18TYPE AND QUANTITY,ACCOMMODATION ACCOMMODATION TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF ACCOMMODATIONS INCLUDED. 1D AND 1A MODE REPLY13AE15 AWHXD /D/ 07ATTACHMENT,RIBBON RIBBON ATTACHMENT AN INDICATION OF WHETHER OR NOT A RIBBON ATTACHMENT IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AWHYA 19NUMBER,TYPE,STITCH STITCH TYPE NUMBER THE STITCH TYPE NUMBER ASSIGNED TO THE ITEM. 1A MODE REPLY 0 AWHZD 19SEWING FOR WHICH DESIGNED,ZIGZAG ZIGZAG SEWING FOR WHICH DESIGNED INDICATES THE ZIGZAG SEWING FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL93 AWJAD 18TYPE,MOUNTING,TABLE TABLE MOUNTING TYPE INDICATES THE TYPE OF TABLE MOUNTING PROVIDED. SELECT REPLY CODE 10AA78 AWJBJ /D/ 04LENGTH,COUPLING,FIRST END FIRST END COUPLING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FIRST END COUPLING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AWJCJ /D/ 04DIAMETER,OUTSIDE,SECOND END COUPLING SECOND END COUPLING OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SECOND END COUPLING,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AWJDJ /D/ 04LENGTH,SLEEVE,FIRST END BEARING FIRST END BEARING SLEEVE LENGTH THE DISTANCE MEASURED ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS OF THE FIRST END BEARING SLEEVE. 2D AND 1B MODE REPLY21AA051AC20 AWJEA 12QUANTITY,HOLE,PARTLY THROUGH PARTLY THROUGH HOLE QUANTITY THE NUMBER OF PARTLY THROUGH HOLES PROVIDED. 1A MODE REPLY 0 AWJFD 14SHAPE,CROSS-SECTIONAL,ROD SHANK ROD SHANK CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE ROD SHANK WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 AWJGJ 04LENGTH,SHANK,ROD ROD SHANK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A ROD SHANK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AWJHD 07CHARACTERISTIC,MOUNTING MOUNTING CHARACTERISTIC AN INDICATION OF THE MOUNTING CHARACTERISTICS OF THE ITEM. SELECT REPLY CODE 10AM38 AWJJD 18TYPE,CRUSHER CRUSHER TYPE INDICATES THE TYPE OF CRUSHER PROVIDED. SELECT REPLY CODE 10AK54 AWJKB 10HORSEPOWER REQUIRED HORSEPOWER REQUIRED THE HORSEPOWER REQUIRED TO OPERATE THE ITEM. 1B MODE REPLY 0 AWJLD /D/ 19CONDITION,SURFACE,INSIDE INSIDE SURFACE CONDITION THE CONDITION OF THE ITEM WITH RESPECT TO THE TEXTURE OF THE INNER SURFACE. SELECT REPLY CODE 10AK39 AWJMJ 10WEIGHT FOR WHICH DESIGNED,PROJECTILE PROJECTILE WEIGHT FOR WHICH DESIGNED THE TOTAL WEIGHT OF THE PROJECTILE FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY12AG67 AWJNJ /D/ 10WEIGHT,UNIT,UNPACKAGED UNPACKAGED UNIT WEIGHT THE MEASURED WEIGHT OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING MATERIAL. PLEASE USE MRC CTJS IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1B MODE REPLY12AG67 AWJPD /D/ 07SHAFT SHAFT AN INDICATION OF WHETHER OR NOT A SHAFT IS INCLUDED. SELECT REPLY CODE 10AA49 AWJQD /D/ 07BEARINGS BEARINGS AN INDICATION OF WHETHER OR NOT BEARINGS ARE INCLUDED. PLEASE USE MRC ABFF FOR NIINS WERE ANSWERED WITH "INCLUDED" IN PLACE OF THIS CANCELLED MRC. SELECT REPLY CODE 10AA49 AWJRD /D/ 07REPLACEABILITY,FAN FAN REPLACEABILITY AN INDICATION OF WHETHER OR NOT THE FAN IS REPLACEABLE. SELECT REPLY CODE 10AG84 AWJSJ /D/ 04DIAMETER,FAN FAN DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FAN,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AWJTH /D/ 01COLOR AND LOCATION COLOR AND LOCATION A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY,AND ITS LOCATION ON THE ITEM. PLEASE USE MRC HUES WITH THE USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. 2D MODE REPLY 26AD063AJ91 AWJWL 16STYLE,ARM ARM STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ARM. 1L MODE REPLY 0 AWJXL 16STYLE,HANDWHEEL HANDWHEEL STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HANDWHEEL. 1L MODE REPLY 0 AWJYL 16STYLE,FACILITY,DRIVE DRIVE FACILITY STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE DRIVE FACILITY. 1L MODE REPLY 0 AWJZD 13THREAD SERIES DESIGNATOR,FACILITY,DRIVE DRIVE FACILITY THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A GIVEN DIAMETER OF THE DRIVE FACILITY. SELECT REPLY CODE 10AH06 AWKAJ 04LENGTH,OVERALL,CRANK CRANK OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CRANK. 2D AND 1B MODE REPLY21AA051AC20 AWKBD 19PORTION,FOLDING FOLDING PORTION AN INDICATION OF THE PORTION OF THE ITEM THAT FOLDS. SELECT REPLY CODE 10AC42 AWKCD 11METHOD,MOUNTING,HANDLE HANDLE MOUNTING METHOD THE MEANS USED TO ATTACH THE HANDLE TO THE ITEM. SELECT REPLY CODE 10AM39 AWKDD /D/ 07FEATURE,ROTATING,HANDLE HANDLE ROTATING FEATURE AN INDICATION OF WHETHER OR NOT A HANDLE ROTATING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AWKED /D/ 07WEIGHT,COUNTERBALANCING,HANDLE HANDLE COUNTERBALANCING WEIGHT AN INDICATION OF WHETHER OR NOT A WEIGHT IS INCLUDED TO OFFSET THE WEIGHT OF THE HANDLE. SELECT REPLY CODE 10AA49 AWKFD /D/ 07RATCHET RATCHET AN INDICATION OF WHETHER OR NOT A RATCHET IS INCLUDED. SELECT REPLY CODE 10AA49 AWKGJ 04LENGTH,THROW,CRANK CRANK THROW LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AWKHJ 04LENGTH,ARM ARM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ARM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AWKJA 12QUANTITY,SPOKE SPOKE QUANTITY THE NUMBER OF SPOKES PROVIDED. 1A MODE REPLY 0 AWKKB 04ANGLE IN DEG,SPOKE SPOKE ANGLE IN DEG NONE. 1B MODE REPLY 0 AWKLA 12QUANTITY,GRIP GRIP QUANTITY NONE. 1A MODE REPLY 0 AWKMJ 04LENGTH FROM END TO ARM CENTER LENGTH FROM END TO ARM CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AWKNJ 04DIAMETER,OUTSIDE,DRIVE FACILITY DRIVE FACILITY OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AWKPA 12QUANTITY,PIN PIN QUANTITY THE NUMBER OF PINS PROVIDED. 1A MODE REPLY 0 AWKQJ 04LENGTH,DRIVE DRIVE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AWKRJ 04LENGTH,SHELL SHELL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SHELL,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AWKSJ 04DIAMETER,OUTSIDE,SHELL SHELL OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SHELL,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AWKTA 12QUANTITY,CONNECTION,WATER WATER CONNECTION QUANTITY THE NUMBER OF WATER CONNECTIONS PROVIDED. 1A MODE REPLY 0 AWKWD 18TYPE,CONNECTION,WATER WATER CONNECTION TYPE INDICATES THE TYPE OF WATER CONNECTION/S/. SELECT REPLY CODE 10AB76 AWKXA 12QUANTITY,CONNECTION,REFRIGERANT INLET REFRIGERANT INLET CONNECTION QUANTITY THE NUMBER OF REFRIGERANT INLET CONNECTIONS PROVIDED. 1A MODE REPLY 0 AWKYD 18TYPE,CONNECTION,REFRIGERANT INLET REFRIGERANT INLET CONNECTION TYPE INDICATES THE TYPE OF REFRIGERANT INLET CONNECTION/S/. SELECT REPLY CODE 10AB76 AWKZG 04SIZE,CONNECTION,WATER WATER CONNECTION SIZE DESIGNATES THE SIZE OF THE WATER CONNECTION. FULL TEXT WRITE-IN 0 AWLAG 04SIZE,CONNECTION,REFRIGERANT INLET REFRIGERANT INLET CONNECTION SIZE DESIGNATES THE SIZE OF THE REFRIGERANT INLET CONNECTION. FULL TEXT WRITE-IN 0 AWLBA 12QUANTITY,CONNECTION,REFRIGERANT OUTLET REFRIGERANT OUTLET CONNECTION QUANTITY THE NUMBER OF REFRIGERANT OUTLET CONNECTIONS PROVIDED. 1A MODE REPLY 0 AWLCD 18TYPE,CONNECTION,REFRIGERANT OUTLET REFRIGERANT OUTLET CONNECTION TYPE INDICATES THE TYPE OF REFRIGERANT OUTLET CONNECTION/S/. SELECT REPLY CODE 10AB76 AWLDG 04SIZE,CONNECTION,OUTLET,REFRIGERANT REFRIGERANT OUTLET CONNECTION SIZE DESIGNATES THE SIZE OF THE REFRIGERANT OUTLET CONNECTION. FULL TEXT WRITE-IN 0 AWLED 18TYPE,CONNECTION,GAS GAS CONNECTION TYPE INDICATES THE TYPE OF GAS CONNECTION. SELECT REPLY CODE 10AB76 AWLFG 04SIZE,CONNECTION,GAS GAS CONNECTION SIZE DESIGNATES THE SIZE OF THE GAS CONNECTION. FULL TEXT WRITE-IN 0 AWLGD 18TYPE,UNIT,COMPRESSING COMPRESSING UNIT TYPE INDICATES THE TYPE OF COMPRESSING UNIT PROVIDED. SELECT REPLY CODE 10AK04 AWLHD /D/ 18TYPE,DESIGN,COMPRESSING UNIT COMPRESSING UNIT DESIGN TYPE INDICATES THE DESIGN TYPE OF THE COMPRESSING UNIT. SELECT REPLY CODE 10AK54 AWLJA 12QUANTITY,CYLINDER,COMPRESSING UNIT COMPRESSING UNIT CYLINDER QUANTITY THE NUMBER OF CYLINDERS PROVIDED IN THE COMPRESSING UNIT. 1A MODE REPLY 0 AWLKJ 04DIAMETER,BORE,CYLINDER,COMPRESSING UNIT COMPRESSING UNIT CYLINDER BORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CIRCULAR CROSS-SECTIONAL PLANE OF THE CYLINDER BORE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AWLLD /D/ 19MEDIUM,COOLING,CONDENSER CONDENSER COOLING MEDIUM THE COOLING MEDIUM USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE CONDENSER. USE MRC ACZV AND ISAC TO TABLE 0094 SELECT REPLY CODE 10AB75 AWLMJ 04LENGTH,OVERALL,CONDENSER CONDENSER OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CONDENSER. 2D AND 1B MODE REPLY21AA051AC20 AWLNJ 04DIAMETER,OUTSIDE,CONDENSER SHELL CONDENSER SHELL OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CONDENSER SHELL,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AWLPD 18TYPE,CONDENSER CONDENSER TYPE INDICATES THE TYPE OF CONDENSER. SELECT REPLY CODE 10AM41 AWLQA 12QUANTITY,TUBE,COIL COIL TUBE QUANTITY THE NUMBER OF TUBES PROVIDED IN THE COIL. 1A MODE REPLY 0 AWLRA 12QUANTITY,CIRCUIT,TUBE TUBE CIRCUIT QUANTITY THE NUMBER OF TUBE CIRCUITS PROVIDED. 1A MODE REPLY 0 AWLSD 18TYPE,CONNECTION CONNECTION TYPE INDICATES THE TYPE OF CONNECTION/S/. SELECT REPLY CODE 10AB76 AWLTG 04SIZE,CONNECTION,SUPPLY SUPPLY CONNECTION SIZE DESIGNATES THE SIZE OF THE SUPPLY CONNECTION. FULL TEXT WRITE-IN 0 AWLWG 04SIZE,CONNECTION,RETURN RETURN CONNECTION SIZE DESIGNATES THE SIZE OF THE RETURN CONNECTION. FULL TEXT WRITE-IN 0 AWLXA 12QUANTITY,MOTOR,ELECTRIC ELECTRIC MOTOR QUANTITY THE NUMBER OF ELECTRIC MOTORS PROVIDED. 1A MODE REPLY 0 AWLYD 19COMPONENT FOR WHICH DESIGNED COMPONENT FOR WHICH DESIGNED THE COMPONENT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AM42 AWLZD /D/ 07CASE WITH BUILT-IN CONDENSATE DRAIN PAN CASE WITH BUILT-IN CONDENSATE DRAIN PAN AN INDICATION OF WHETHER OR NOT A CASE WITH A BUILT-IN CONDENSATE DRAIN PAN IS INCLUDED. SELECT REPLY CODE 10AA49 AWMAD 18TYPE,FAN FAN TYPE INDICATES THE TYPE OF FAN PROVIDED. SELECT REPLY CODE 10AL87 AWMBD 18TYPE,DRIVE,FAN FAN DRIVE TYPE INDICATES THE TYPE OF DRIVE PROVIDED FOR THE FAN. SELECT REPLY CODE 10AG25 AWMCD /D/ 07HANDLE,VALVE VALVE HANDLE AN INDICATION OF WHETHER OR NOT VALVE HANDLES ARE INCLUDED. SELECT REPLY CODE 10AA49 AWMDB 10TEMP AT MINIMUM CAPACITY IN DEG FAHRENHEIT,REFRIGERANT REFRIGERANT TEMP AT MINIMUM CAPACITY IN DEG FAHRENHEIT THE REFRIGERANT TEMPERATURE AT THE MINIMUM CAPACITY,EXPRESSED IN DEGREES FAHRENHEIT. 1B MODE REPLY 0 AWMEJ /D/ 04SIZE FOR WHICH DESIGNED,HOSE,NOMINAL NOMINAL HOSE SIZE FOR WHICH DESIGNED THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE DIAMETER OF A HOSE. 1D AND 1B MODE REPLY11AA05 AWMFJ 04DIAMETER HOSE ACCOMMODATED,INSIDE INSIDE DIAMETER HOSE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR A HOSE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AWMGA 13THREAD SIZE,EXTERNAL EXTERNAL THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF AN EXTERNALLY THREADED ITEM. 1A MODE REPLY 0 AWMHA 13THREAD SIZE,INTERNAL INTERNAL THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF AN INTERNALLY THREADED ITEM. 1A MODE REPLY 0 AWMJJ 04DIAMETER,INSIDE,RESTRICTION PASSAGE RESTRICTION PASSAGE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE RESTRICTION PASSAGE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AWMKD 14SHAPE,FLANGE,MOUNTING MOUNTING FLANGE SHAPE THE PHYSICAL CONFIGURATION OF THE MOUNTING FLANGE. SELECT REPLY CODE 10AD07 AWMLJ /D/ 19CENTER,BOLT,OVAL FLANGE OVAL FLANGE BOLT CENTER THE DIMENSION OF THE BOLT CENTER ON AN OVAL FLANGE. 2D AND 1B MODE REPLY21AA051AC20 AWMMD /D/ 07FEATURE,CONNECTION,EQUALIZING EQUALIZING CONNECTION FEATURE AN INDICATION OF WHETHER OR NOT AN EQUALIZING CONNECTION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AWMND /D/ 07CONNECTION,DRAIN DRAIN CONNECTION AN INDICATION OF WHETHER OR NOT A DRAIN CONNECTION IS INCLUDED. SELECT REPLY CODE 10AA49 AWMPD /D/ 07PLUG,SAFETY SAFETY PLUG AN INDICATION OF WHETHER OR NOT A SAFETY PLUG IS INCLUDED. SELECT REPLY CODE 10AA49 AWMQD /D/ 07INDICATOR,LEVEL,LIQUID LIQUID LEVEL INDICATOR AN INDICATION OF WHETHER OR NOT A LIQUID LEVEL INDICATOR IS INCLUDED. SELECT REPLY CODE 10AA49 AWMRD 18TYPE,INDICATOR,LIQUID LEVEL LIQUID LEVEL INDICATOR TYPE INDICATES THE TYPE OF LIQUID LEVEL INDICATOR. SELECT REPLY CODE 10AD51 AWMSD 11METHOD,MONITORING MONITORING METHOD THE MEANS USED FOR MONITORING THE ITEM. SELECT REPLY CODE 10AL28 AWMTJ 10FREQUENCY RATING,SIGNAL,INPUT INPUT SIGNAL FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE INPUT SIGNAL IS RATED. 2D AND 1B MODE REPLY21AC321AC20 AWMWD 11METHOD,CONDENSING CONDENSING METHOD THE MEANS USED TO FORM LIQUID. SELECT REPLY CODE 10AE81 AWMXD /D/ 09MATERIAL,SHEET,TUBE TUBE SHEET MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TUBE SHEET IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AWMYD /D/ 09MATERIAL,BOX,WATER WATER BOX MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WATER BOX IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AWMZD 11METHOD,ATTACHMENT,TUBE TUBE ATTACHMENT METHOD THE MEANS BY WHICH THE TUBE/S/ IS ATTACHED. SELECT REPLY CODE 10AA62 AWNAD /D/ 08LOCATION,EJECTOR,AIR AIR EJECTOR LOCATION INDICATES THE LOCATION OF THE AIR EJECTOR. SELECT REPLY CODE 10AJ91 AWNBD 18TYPE,EJECTOR EJECTOR TYPE INDICATES THE TYPE OF EJECTOR PROVIDED. SELECT REPLY CODE 10AG89 AWNCJ /D/ 10PRESSURE,OPERATING,INTERNAL INTERNAL OPERATING PRESSURE THE NOMINAL EXERTED OUTWARD FORCE,PER UNIT OF AREA,FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AB18 AWNDA 12QUANTITY PER UNIT,STAGE STAGE QUANTITY PER UNIT THE NUMBER OF STAGES PER UNIT. 1A MODE REPLY 0 AWNED /D/ 09MATERIAL,CHEST,STEAM STEAM CHEST MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE STEAM CHEST IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AWNFA 12QUANTITY PER STAGE,NOZZLE NOZZLE QUANTITY PER STAGE THE NUMBER OF NOZZLES PER STAGE. 1A MODE REPLY 0 AWNGD /D/ 19FORM,TUBE TUBE FORM THE SHAPE OR CONFIGURATION OF THE TUBE/S/. SELECT REPLY CODE 10AA62 AWNHD /D/ 07NUTS,COUPLING COUPLING NUTS AN INDICATION OF WHETHER OR NOT COUPLING NUTS ARE INCLUDED. SELECT REPLY CODE 10AA49 AWNJJ 10PRESSURE,CHAMBER,COOLANT COOLANT CHAMBER PRESSURE THE NOMINAL OUTWARD FORCE,PER UNIT OF AREA,OF THE COOLANT CHAMBER. 1D AND 1B MODE REPLY11AB18 AWNKH /D/ 18TYPE AND FUNCTION,CONNECTION CONNECTION TYPE AND FUNCTION INDICATES THE TYPE AND PURPOSE OF THE CONNECTION. 2D MODE REPLY 22AA842AE81 AWNLJ 10TEMP,COOLANT,INPUT INPUT COOLANT TEMP THE INPUT TEMPERATURE OF THE COOLANT. 1D AND 1B MODE REPLY11AB36 AWNMD /D/ 18TYPE,ELEMENT,COOLING COOLING ELEMENT TYPE INDICATES THE TYPE OF COOLING ELEMENT PROVIDED. SELECT REPLY CODE 10AA93 AWNND 18TYPE,SUPPLY,POWER POWER SUPPLY TYPE INDICATES THE TYPE OF POWER SUPPLY PROVIDED. SELECT REPLY CODE 10AM43 AWNPJ 10VOLTAGE RATING,OUTPUT,POWER SUPPLY POWER SUPPLY OUTPUT VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,OF OUTPUT OF THE POWER SUPPLY. 2D AND 1B MODE REPLY21AB631AC20 AWNQD 18TYPE,CURRENT,POWER SUPPLY OUTPUT POWER SUPPLY OUTPUT CURRENT TYPE INDICATES THE TYPE OF POWER SUPPLY OUTPUT CURRENT PROVIDED. SELECT REPLY CODE 10AB62 AWNRJ 10CURRENT RATING,OUTPUT,POWER SUPPLY POWER SUPPLY OUTPUT CURRENT RATING THE OUTPUT CURRENT RATING OF THE POWER SUPPLY. 2D AND 1B MODE REPLY21AC301AC20 AWNSG 18TYPE,SIGNAL,INPUT INPUT SIGNAL TYPE INDICATES THE TYPE OF INPUT SIGNAL. FULL TEXT WRITE-IN 0 AWNTD /D/ 18TYPE,STAGE STAGE TYPE INDICATES THE TYPE OF STAGE. PLEASE USE MRC BMMH IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AF09 AWNWJ 04SIZE,PIPE,NOMINAL,INLET CONNECTION INLET CONNECTION NOMINAL PIPE SIZE THE NOMINAL VALUE USED TO DEFINE THE DIAMETER OF THE INLET CONNECTION PIPE. 1D AND 1B MODE REPLY11AA05 AWNXD /D/ 07ADAPTER,INLET INLET ADAPTER AN INDICATION OF WHETHER OR NOT AN INLET ADAPTER IS INCLUDED. SELECT REPLY CODE 10AA49 AWNYD /D/ 07VALVE,RELIEF,AUTOMATIC AUTOMATIC RELIEF VALVE AN INDICATION OF WHETHER OR NOT AN AUTOMATIC RELIEF VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 AWNZD /D/ 07FLOWMETER FLOWMETER AN INDICATION OF WHETHER OR NOT A FLOWMETER IS INCLUDED. SELECT REPLY CODE 10AA49 AWPAD 18TYPE,THERMOSTAT THERMOSTAT TYPE INDICATES THE TYPE OF THERMOSTAT. SELECT REPLY CODE 10AM44 AWPBD /D/ 07FEATURE,CHANGING,RF CONNECTOR RF CONNECTOR CHANGING FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE IS INCLUDED FOR RF CONNECTOR CHANGING. SELECT REPLY CODE 10AA49 AWPCG /D/ 08LOCATION,INSTALLATION,SHIPBOARD SHIPBOARD INSTALLATION LOCATION INDICATES THE LOCATION ON A VESSEL WHERE THE ITEM IS INSTALLED. FULL TEXT WRITE-IN 0 AWPDB 04DIAMETER SURFACE ANGLE,OUTSIDE,IN DEG OUTSIDE DIAMETER SURFACE ANGLE IN DEG NONE. 1B MODE REPLY 0 AWPEJ 04DIAMETER,INSIDE,SMALL SMALL INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AWPFB 04ANGLE BETWEEN ACCOMMODATIONS IN DEG ANGLE BETWEEN ACCOMMODATIONS IN DEG THE ANGLE BETWEEN ACCOMMODATIONS,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AWPGJ 04RADIUS FROM GEOMETRIC AXIS TO ACCOMMODATION RADIUS FROM GEOMETRIC AXIS TO ACCOMMODATION THE MEASUREMENT OF A STRAIGHT LINE FROM THE CENTER OF THE ITEM TO THE CENTER OF THE ACCOMMODATION. 2D AND 1B MODE REPLY21AA051AC20 AWPHD /D/ 07THREAD,BEVELED BEVELED THREAD AN INDICATION OF WHETHER OR NOT A BEVELED THREAD IS INCLUDED. SELECT REPLY CODE 10AA49 AWPJD 08LOCATION,DIAMETER,MAJOR,TAPER TAPER MAJOR DIAMETER LOCATION INDICATES THE LOCATION OF THE TAPER MAJOR DIAMETER. SELECT REPLY CODE 10AJ91 AWPKD /D/ 07SERRATION,INTERNAL,BORE ANNULAR BORE ANNULAR INTERNAL SERRATION AN INDICATION OF WHETHER OR NOT A BORE ANNULAR INTERNAL SERRATION/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 AWPLD /D/ 07NOTCH,LOCKING,SETSCREW SETSCREW LOCKING NOTCH AN INDICATION OF WHETHER OR NOT A SETSCREW LOCKING NOTCH IS INCLUDED. SELECT REPLY CODE 10AA49 AWPMA 12QUANTITY,SERRATION,OUTER OUTER SERRATION QUANTITY THE NUMBER OF SERRATIONS ON THE OUTER CIRCUMFERENCE. 1A MODE REPLY 0 AWPNA 12QUANTITY,SERRATION,INNER INNER SERRATION QUANTITY THE NUMBER OF SERRATIONS ON THE INNER CIRCUMFERENCE. 1A MODE REPLY 0 AWPPD 11METHOD,APPLICATION,SOLUTION SOLUTION APPLICATION METHOD THE MEANS BY WHICH THE SOLUTION IS APPLIED. SELECT REPLY CODE 10AF22 AWPQD /D/ 07LIGHT,INTEGRAL INTEGRAL LIGHT AN INDICATION OF WHETHER OR NOT AN INTEGRAL LIGHT IS PROVIDED. SELECT REPLY CODE 10AB22 AWPRH /D/ 18TYPE AND LOCATION,CONNECTION,END END CONNECTION TYPE AND LOCATION INDICATES THE TYPE OF END CONNECTION AND ITS LOCATION ON THE ITEM. 2D MODE REPLY 22AB763AJ91 AWPSD 02DESIGN,SPECIAL,CONNECTION CONNECTION SPECIAL DESIGN THE SPECIAL DESIGN OF THE CONNECTION. SELECT REPLY CODE 10AB76 AWPTD /D/ 07FEATURE,DESIGN,INCLINED INCLINED DESIGN FEATURE AN INDICATION OF WHETHER OR NOT AN INCLINED DESIGN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AWPWD /D/ 07FEATURE,READING,DIRECT DIRECT READING FEATURE AN INDICATION OF WHETHER OR NOT A DIRECT READING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AWPXJ 04DIAMETER,OVERALL,PLUNGER PLUNGER OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF A PLUNGER. 2D AND 1B MODE REPLY21AA051AC20 AWPYJ 04LENGTH,PLUNGER PLUNGER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A PLUNGER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AWPZD /D/ 07DEVICE,LOCKING,CASE CASE LOCKING DEVICE AN INDICATION OF WHETHER OR NOT A CASE LOCKING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 AWQAD 19PROCESS,EDGE,BORE BORE EDGE PROCESS AN INDICATION OF THE PROCESS APPLIED TO THE BORE EDGE. SELECT REPLY CODE 10AD07 AWQBD 08LOCATION,END,PROCESS PROCESS END LOCATION INDICATES THE LOCATION OF THE END ON WHICH THE PROCESS IS TO BE APPLIED. SELECT REPLY CODE 10AJ91 AWQCD /D/ 19SERRATIONS OMITTED FOR CLOSE EDGE INSTALLATION,OUTER,SIDE SIDE OUTER SERRATIONS OMITTED FOR CLOSE EDGE INSTALLATION AN INDICATION OF THE SIDE/S/ FROM WHICH OUTER SERRATIONS HAVE BEEN OMITTED TO PROVIDE FOR CLOSE EDGE INSTALLATION. SELECT REPLY CODE 10AJ91 AWQDJ 10STRENGTH RATING STRENGTH RATING THE LOAD IN TENSION APPLIED IN A LONGITUDINAL DIRECTION OR THE LOAD THAT CAN BE APPLIED IN A PLANE PERPENDICULAR TO THE AXIAL CENTERLINE WITHOUT RUPTURE OR PERMANENT DEFORMATION OF THE MATERIAL. 2D AND 1B MODE REPLY21AB182AM45 AWQEA /D/ 16STYLE,OPENING,GAP GAP OPENING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE GAP OPENING. 1A MODE REPLY 0 AWQFJ 10TAKEUP,END PLAY END PLAY TAKEUP NONE. 2D AND 1B MODE REPLY21AA051AC20 AWQGJ 04LENGTH,OVERLAP OVERLAP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN OVERLAP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AWQHJ 04SIZE,NOMINAL NOMINAL SIZE DESIGNATES THE NOMINAL SIZE OF AN ITEM,SUCH AS LENGTH,WIDTH,DIAMETER,AND THE LIKE. 1D AND 1B MODE REPLY11AA05 AWQJD /D/ 18TYPE FOR WHICH DESIGNED,PIPE/TUBING PIPE/TUBING TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF PIPE AND/OR TUBING FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 AWQKG /D/ 19NAME,ITEM/BRAND,MANUFACTURER MANUFACTURER ITEM/BRAND NAME AN INDICATION OF THE ITEM AND/OR BRAND NAME OF THE MANUFACTURER. FULL TEXT WRITE-IN 0 AWQLJ 10ROTATION IN DEG ROTATION IN DEG THE MEASUREMENT OF ROTATION,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 AWQMJ 10TORQUE RATING,DRIVE,OUTPUT OUTPUT DRIVE TORQUE RATING THE RATED TORQUE OF THE OUTPUT DRIVE. 1D AND 1B MODE REPLY11AA56 AWQND /D/ 07CONTROL,SWITCH,LIMIT LIMIT SWITCH CONTROL AN INDICATION OF WHETHER OR NOT A LIMIT SWITCH CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 AWQPD 11METHOD,RESET,THERMAL PROTECTOR THERMAL PROTECTOR RESET METHOD THE MEANS USED TO RESET THE THERMAL PROTECTOR. SELECT REPLY CODE 10AA77 AWQQJ 04DEPTH RATING,OPERATING,MAXIMUM MAXIMUM OPERATING DEPTH RATING THE MAXIMUM DEPTH AT WHICH THE ITEM IS RATED TO FUNCTION. 1D AND 1B MODE REPLY11AA05 AWQRD /D/ 07OVERRIDE,MANUAL MANUAL OVERRIDE AN INDICATION OF WHETHER OR NOT A MANUAL OVERRIDE IS INCLUDED. SELECT REPLY CODE 10AA49 AWQSD /D/ 19FACILITY,MOUNTING MOUNTING FACILITY THE FACILITY FOR MOUNTING THE ITEM. SELECT REPLY CODE 10AM39 AWQTJ 10CAPACITY RATING,FUELING,MAXIMUM MAXIMUM FUELING CAPACITY RATING THE MAXIMUM RATED FUELING CAPACITY DELIVERED BY THE ITEM. 1D AND 1B MODE REPLY11AC64 AWQWB 10SPEED AT RATED CAPACITY IN RPM,OPERATING,FUELING FUELING OPERATING SPEED AT RATED CAPACITY IN RPM THE SPEED OF THE FUELING REQUIRED TO PRODUCE ITS RATED CAPACITY,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 AWQXJ /D/ 10HEAD,TOTAL,FUELING FUELING TOTAL HEAD THE SUM OF THE FUELING TOTAL DISCHARGE HEAD AND THE TOTAL SUCTION LIFT. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1D AND 1B MODE REPLY12AB16 AWQYJ 10CAPACITY RATING,DEFUELING,MAXIMUM MAXIMUM DEFUELING CAPACITY RATING THE MAXIMUM RATED DEFUELING CAPACITY DELIVERED BY THE ITEM. 1D AND 1B MODE REPLY11AC64 AWQZB 10SPEED AT RATED CAPACITY IN RPM,OPERATING,DEFUELING DEFUELING OPERATING SPEED AT RATED CAPACITY IN RPM THE SPEED OF THE DEFUELING REQUIRED TO PRODUCE ITS RATED CAPACITY,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 AWRAJ 04DIAMETER,OUTSIDE,NOMINAL,FIRST CHAIN LINK BUSHING FIRST CHAIN LINK BUSHING NOMINAL OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AWRBJ 04DIAMETER,NOMINAL,FIRST CHAIN LINK ROLLER FIRST CHAIN LINK ROLLER NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AWRCJ 04DIAMETER,MATERIAL,CHAIN CHAIN MATERIAL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MATERIAL OF WHICH THE CHAIN LINKS ARE MADE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AWRDG /D/ 19METAL FOR WHICH FORMULATED,SPECIFIC SPECIFIC METAL FOR WHICH FORMULATED THE METAL FOR WHICH THE ITEM IS FORMULATED. FULL TEXT WRITE-IN 0 AWREJ 04WIDTH BETWEEN PLATES,NOMINAL,FIRST CHAIN LINK FIRST CHAIN LINK NOMINAL WIDTH BETWEEN PLATES NONE. 1D AND 1B MODE REPLY11AA05 AWRFJ 04WIDTH,NOMINAL,FIRST CHAIN LINK FIRST CHAIN LINK NOMINAL WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AWRGJ 04HEIGHT ABOVE CENTER,NOMINAL,FIRST CHAIN LINK HOLE FIRST CHAIN LINK HOLE NOMINAL HEIGHT ABOVE CENTER NONE. 1D AND 1B MODE REPLY11AA05 AWRHJ 04DIAMETER,NOMINAL,FIRST CHAIN LINK HOLE FIRST CHAIN LINK HOLE NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AWRJJ /D/ 04LENGTH,PIN,EXTENDED,FIRST CHAIN LINK FIRST CHAIN LINK EXTENDED PIN LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AWRKJ 04DISTANCE FROM CENTER,NOMINAL,FIRST CHAIN LINK HOLE FIRST CHAIN LINK HOLE NOMINAL DISTANCE FROM CENTER NONE. 1D AND 1B MODE REPLY11AA05 AWRLJ 04DISTANCE BETWEEN HOLE CENTERS,CHAIN LINK,FIRST FIRST CHAIN LINK DISTANCE BETWEEN HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AWRMJ /D/ 04DISTANCE FROM CENTER,HOLE,FIRST,FIRST CHAIN LINK FIRST CHAIN LINK FIRST HOLE DISTANCE FROM CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AWRNJ /D/ 04DISTANCE FROM CENTER,HOLE,SECOND,FIRST CHAIN LINK FIRST CHAIN LINK SECOND HOLE DISTANCE FROM CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AWRPJ /D/ 04LENGTH,EXTENSION,FIRST CHAIN LINK FIRST CHAIN LINK EXTENSION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AWRQJ /D/ 04DISTANCE,BOLT HOLE CENTERLINE TO EDGE,FIRST CHAIN LINK FIRST CHAIN LINK BOLT HOLE CENTERLINE TO EDGE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AWRRJ 04WIDTH,PLATE,SECOND CHAIN LINK SECOND CHAIN LINK PLATE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AWRSJ 04WIDTH AT BUSHING END,PLATE,SECOND CHAIN LINK SECOND CHAIN LINK PLATE WIDTH AT BUSHING END NONE. 2D AND 1B MODE REPLY21AA051AC20 AWRTJ 04WIDTH AT PIN END,PLATE,SECOND CHAIN LINK SECOND CHAIN LINK PLATE WIDTH AT PIN END NONE. 2D AND 1B MODE REPLY21AA051AC20 AWRWJ 04THICKNESS,NOMINAL,SECOND CHAIN LINK PLATE SECOND CHAIN LINK PLATE NOMINAL THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 AWRXJ 04DIAMETER,NOMINAL,SECOND CHAIN LINK PIN SECOND CHAIN LINK PIN NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AWRYJ 04DIAMETER,OUTSIDE,NOMINAL,SECOND CHAIN LINK BUSHING SECOND CHAIN LINK BUSHING NOMINAL OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AWRZJ 04DIAMETER,NOMINAL,SECOND CHAIN LINK ROLLER SECOND CHAIN LINK ROLLER NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AWSAJ 04WIDTH BETWEEN PLATES,NOMINAL,SECOND CHAIN LINK SECOND CHAIN LINK NOMINAL WIDTH BETWEEN PLATES NONE. 1D AND 1B MODE REPLY11AA05 AWSBJ /D/ 04WIDTH,NOMINAL,SECOND CHAIN LINK SECOND CHAIN LINK NOMINAL WIDTH NONE. MRC DISCONTINUED WITH NO REPLACMENT ON 01/12/2024. 1D AND 1B MODE REPLY11AA05 AWSCJ 04HEIGHT ABOVE CENTER,NOMINAL,SECOND CHAIN LINK HOLE SECOND CHAIN LINK HOLE NOMINAL HEIGHT ABOVE CENTER NONE. 1D AND 1B MODE REPLY11AA05 AWSDJ 04DIAMETER,NOMINAL,SECOND CHAIN LINK HOLE SECOND CHAIN LINK HOLE NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AWSEJ 04LENGTH,PIN,EXTENDED,SECOND CHAIN LINK SECOND CHAIN LINK EXTENDED PIN LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AWSFJ 04DISTANCE FROM CENTER,NOMINAL,SECOND CHAIN LINK HOLE SECOND CHAIN LINK HOLE NOMINAL DISTANCE FROM CENTER NONE. 1D AND 1B MODE REPLY11AA05 AWSGJ 04DISTANCE BETWEEN CENTERS,CHAIN LINK,SECOND SECOND CHAIN LINK DISTANCE BETWEEN HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AWSHJ /D/ 04DISTANCE FROM CENTER,HOLE,FIRST,SECOND CHAIN LINK SECOND CHAIN LINK FIRST HOLE DISTANCE FROM CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AWSJJ /D/ 04DISTANCE FROM CENTER,HOLE,SECOND,SECOND CHAIN LINK SECOND CHAIN LINK SECOND HOLE DISTANCE FROM CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AWSKJ /D/ 04LENGTH,EXTENSION,SECOND CHAIN LINK SECOND CHAIN LINK EXTENSION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AWSLJ /D/ 04DISTANCE,BOLT HOLE CENTERLINE TO EDGE,SECOND CHAIN LINK SECOND CHAIN LINK BOLT HOLE CENTERLINE TO EDGE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AWSMJ 04WIDTH,PLATE,LINK LINK PLATE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AWSNJ 04WIDTH AT BUSHING END,PLATE,LINK LINK PLATE WIDTH AT BUSHING END NONE. 2D AND 1B MODE REPLY21AA051AC20 AWSPJ 04WIDTH AT PIN END,PLATE,LINK LINK PLATE WIDTH AT PIN END AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE LINK PLATEAT THE PIN END, IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AWSQJ 04THICKNESS,NOMINAL,LINK PLATE LINK PLATE NOMINAL THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 AWSRJ /D/ 04DIAMETER,PIN,LINK LINK PIN DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AWSSJ 04DIAMETER,OUTSIDE,NOMINAL,LINK BUSHING LINK BUSHING NOMINAL OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AWSTB 04ANGLE IN DEG,SURFACE,UPPER INSIDE DIAMETER UPPER INSIDE DIAMETER SURFACE ANGLE IN DEG NONE. 1B MODE REPLY 0 AWSWB /D/ 04ANGLE IN DEG,SURFACE,LOWER INSIDE DIAMETER LOWER INSIDE DIAMETER SURFACE ANGLE IN DEG NONE. 1B MODE REPLY 0 AWSXJ /D/ 04DIAMETER,SURFACE,FLAT,INSIDE INSIDE FLAT SURFACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AWSYJ /D/ 04DIAMETER,SURFACE,FLAT,OUTSIDE OUTSIDE FLAT SURFACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AWSZJ /D/ 10TIME,OPERATING,SAFE SAFE OPERATING TIME A MEASUREMENT OF THE SAFE OPERATING TIME. 2D AND 1B MODE REPLY22AH182AD21 AWTAJ 10LOAD RATING,TENSION TENSION LOAD RATING THE TENSION STRESS APPLIED TO THE ITEM UNDER LOAD CONDITIONS. 3D AND 1B MODE REPLY31AB101AC202AH00 AWTBJ A18TYPE AND QUANTITY,WIRE,ACCESSORY ACCESSORY WIRE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF ACCESSORY WIRES FURNISHED WITH THE ITEM. 1D AND 1A MODE REPLY13AL37 AWTCJ 10LOAD RATING,COMPRESSION COMPRESSION LOAD RATING THE COMPRESSION STRESS APPLIED TO THE ITEM UNDER LOAD CONDITIONS. 3D AND 1B MODE REPLY31AB101AC202AH00 AWTDH /D/ 19FORM AND LOCATION,CONDUCTOR CONDUCTOR FORM AND LOCATION AN INDICATION OF THE FABRICATED FORM OF THE CONDUCTOR AND ITS LOCATION. 2D MODE REPLY 22AF313AJ91 AWTEJ 10VELOCITY,STROKE,RATED RATED STROKE VELOCITY THE RATE OF LINEAR TRAVEL PER UNIT OF TIME. 1D AND 1B MODE REPLY12AG20 AWTFD /D/ 07GAGE,PRESSURE,CYLINDER CYLINDER PRESSURE GAGE AN INDICATION OF WHETHER OR NOT A CYLINDER PRESSURE GAGE IS INCLUDED. SELECT REPLY CODE 10AA49 AWTGL 16STYLE,END,INLET CONNECTION INLET CONNECTION END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE INLET CONNECTION END. 1L MODE REPLY 0 AWTHL 16STYLE,END,ADAPTER INLET CONNECTION ADAPTER INLET CONNECTION END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ADAPTER INLET CONNECTION END. 1L MODE REPLY 0 AWTJJ 04SIZE,PIPE,NOMINAL,ADAPTER INLET CONNECTION ADAPTER INLET CONNECTION NOMINAL PIPE SIZE THE NOMINAL VALUE USED TO DEFINE THE DIAMETER OF THE ADAPTER INLET CONNECTION PIPE. 1D AND 1B MODE REPLY11AA05 AWTKL 16STYLE,END,OUTLET CONNECTION OUTLET CONNECTION END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE OUTLET CONNECTION END. 1L MODE REPLY 0 AWTLJ 04SIZE,PIPE,NOMINAL,OUTLET CONNECTION OUTLET CONNECTION NOMINAL PIPE SIZE THE NOMINAL VALUE USED TO DEFINE THE DIAMETER OF THE OUTLET CONNECTION PIPE. 1D AND 1B MODE REPLY11AA05 AWTMJ 10TEMP RATING,OPENING OPENING TEMP RATING THE RATED TEMPERATURE AT WHICH THE ITEM STARTS TO OPEN. 2D AND 1B MODE REPLY21AB361AC20 AWTNJ 10TEMP RATING,OPERATING OPERATING TEMP RATING THE TEMPERATURE AT WHICH THE ITEM OPERATES. 2D AND 1B MODE REPLY21AB361AC20 AWTPD /D/ 07RELIEF,PRESSURE,SPRING OPERATED SPRING OPERATED PRESSURE RELIEF AN INDICATION OF WHETHER OR NOT A SPRING OPERATED PRESSURE RELIEF IS PROVIDED. SELECT REPLY CODE 10AB22 AWTQJ 04DISTANCE ACROSS FLATS DISTANCE ACROSS FLATS THE DISTANCE ACROSS THE FLATS. 2D AND 1B MODE REPLY21AA051AC20 AWTRJ 04DISTANCE,INSIDE MOUNTING SURFACE TO VALVE SEAT INSIDE MOUNTING SURFACE TO VALVE SEAT DISTANCE THE DISTANCE FROM THE INSIDE MOUNTING SURFACE TO THE VALVE SEAT. 1D AND 1B MODE REPLY11AA05 AWTSA 12QUANTITY,POLE,MAIN MAIN POLE QUANTITY THE NUMBER OF MAIN POLES INCLUDED. 1A MODE REPLY 0 AWTTA 12QUANTITY,POLE,COMMUTATING COMMUTATING POLE QUANTITY THE NUMBER OF COMMUTATING POLES INCLUDED. 1A MODE REPLY 0 AWTWH /D/ 09MATERIAL AND LOCATION,CONDUCTOR CONDUCTOR MATERIAL AND LOCATION THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CONDUCTOR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT,AND ITS LOCATION. 2D MODE REPLY 26AD093AJ91 AWTXH /D/ 17SURFACE TREATMENT AND LOCATION,CONDUCTOR CONDUCTOR SURFACE TREATMENT AND LOCATION THE COATING,DIP,OR PLATING APPLIED TO THE CONDUCTOR FOR ENVIRONMENTAL PROTECTION OR INCREASED ELECTRICAL CONDUCTIVITY,AND ITS LOCATION. 2D MODE REPLY 26AD093AJ91 AWTYJ /D/A04SIZE AND LOCATION,CONDUCTOR,STRANDED STRANDED CONDUCTOR SIZE AND LOCATION THE DESIGNATION USED TO DESCRIBE THE STRANDED CONDUCTOR SIZE AND ITS LOCATION. 2D AND 1A MODE REPLY21AA443AJ91 AWTZD 19ROTATION,SHAFT,ANGULAR ANGULAR SHAFT ROTATION AN INDICATION OF THE ROTATION OF THE ANGULAR SHAFT. SELECT REPLY CODE 10AJ98 AWWAJ /D/A12QUANTITY PER CONDUCTOR AND LOCATION,STRAND STRAND QUANTITY PER CONDUCTOR AND LOCATION THE TOTAL NUMBER AND LOCATION OF STRANDS PER CONDUCTOR. 1D AND 1A MODE REPLY13AJ91 AWWBJ /D/ 04DIAMETER PER CONDUCTOR AND LOCATION,STRAND STRAND DIAMETER PER CONDUCTOR AND LOCATION THE DIAMETER AND LOCATION OF THE INDIVIDUAL STRANDS OF WIRE USED ON EACH STRANDED CONDUCTOR. 2D AND 1B MODE REPLY21AA053AJ91 AWWCJ /D/A04SIZE PER CONDUCTOR AND LOCATION,AWG,STRAND STRAND AWG SIZE PER CONDUCTOR AND LOCATION INDICATES THE AMERICAN WIRE GAGE SIZE AND LOCATION OF THE INDIVIDUAL STRANDS OF WIRE USED ON EACH STRANDED CONDUCTOR. 1D AND 1A MODE REPLY13AJ91 AWWDJ /D/A04SIZE AND LOCATION,CONDUCTOR,ROUND SOLID ROUND SOLID CONDUCTOR SIZE AND LOCATION THE DESIGNATION USED TO DESCRIBE THE ROUND SOLID CONDUCTOR SIZE,AND ITS LOCATION. 2D AND 1A MODE REPLY21AA443AJ91 AWWEH /D/ 19CONSTRUCTION AND LOCATION,CROSS-SECTIONAL,CONDUCTOR CONDUCTOR CROSS-SECTIONAL CONSTRUCTION AND LOCATION THE CROSS-SECTIONAL CONSTRUCTION AND LOCATION OF A CONDUCTOR. 2D MODE REPLY 23AL593AJ91 AWWFH /D/ 19CHARACTERISTICS,COVERING,CONDUCTOR CONDUCTOR COVERING CHARACTERISTICS AN INDICATION OF THE CONDUCTOR COVERING CHARACTERISTICS. 3D MODE REPLY 32AK896AD093AJ91 AWWGJ 10PRESSURE,MINIMUM,REFRIGERANT SIDE TEST REFRIGERANT SIDE TEST MINIMUM PRESSURE THE MAXIMUM INTERNAL PRESSURE,DETERMINED BY DESTRUCTION TESTS AT WHICH THE ITEM CAN BE EXPECTED TO RUPTURE. 1D AND 1B MODE REPLY12AG20 AWWHJ 10PRESSURE,MINIMUM,WATER SIDE TEST WATER SIDE TEST MINIMUM PRESSURE THE MAXIMUM INTERNAL PRESSURE,DETERMINED BY DESTRUCTION TESTS AT WHICH THE ITEM CAN BE EXPECTED TO RUPTURE. 1D AND 1B MODE REPLY12AG20 AWWJJ 10SURFACE,TRANSFER,HEAT,LIQUID SIDE LIQUID SIDE HEAT TRANSFER SURFACE THE AMOUNT OF HEAT TRANSFER SURFACE ON THE LIQUID SIDE. 1D AND 1B MODE REPLY11AC51 AWWKJ 10SURFACE,TRANSFER,HEAT,GAS SIDE GAS SIDE HEAT TRANSFER SURFACE THE AMOUNT OF HEAT TRANSFER SURFACE ON THE GAS SIDE. 1D AND 1B MODE REPLY11AC51 AWWLJ /D/A19ARRANGEMENT,CONDUCTOR CONDUCTOR ARRANGEMENT THE ARRANGEMENT AND NUMBER OF ARRANGEMENTS OF THE CONDUCTOR. 1D AND 1A MODE REPLY12AK80 AWWMJ 04LENGTH STROKE,COMPRESSING UNIT COMPRESSING UNIT STROKE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE STROKE OF A COMPRESSING UNIT,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AWWNJ 04DIAMETER,NOMINAL,LINK ROLLER LINK ROLLER NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AWWPJ 04WIDTH BETWEEN PLATES,NOMINAL,LINK LINK NOMINAL WIDTH BETWEEN PLATES NONE. 1D AND 1B MODE REPLY11AA05 AWWQJ 04WIDTH,NOMINAL,LINK LINK NOMINAL WIDTH NONE. 1D AND 1B MODE REPLY11AA05 AWWRJ 04HEIGHT ABOVE CENTER,NOMINAL,LINK HOLE LINK HOLE NOMINAL HEIGHT ABOVE CENTER NONE. 1D AND 1B MODE REPLY11AA05 AWWSJ 04DIAMETER,NOMINAL,LINK HOLE LINK HOLE NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 AWWTJ 04LENGTH,PIN,LINK EXTENDED LINK EXTENDED PIN LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AWWWJ 04DISTANCE FROM CENTER,NOMINAL,LINK HOLE LINK HOLE NOMINAL DISTANCE FROM CENTER NONE. 1D AND 1B MODE REPLY11AA05 AWWXJ 04DISTANCE BETWEEN HOLE CENTERS,LINK LINK DISTANCE BETWEEN HOLE CENTERS A MEASUREMENT OF THE DISTANCE BETWEEN THE CENTERLINES OF THE HOLES ON THE LINK. 2D AND 1B MODE REPLY21AA051AC20 AWWYJ /D/ 04DISTANCE FROM CENTER,HOLE,FIRST,LINK LINK FIRST HOLE DISTANCE FROM CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AWWZJ /D/ 04DISTANCE FROM CENTER,HOLE,SECOND,LINK LINK SECOND HOLE DISTANCE FROM CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AWXAJ /D/ 04LENGTH,EXTENSION,LINK LINK EXTENSION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AWXBJ /D/ 04DISTANCE,BOLT HOLE CENTERLINE TO EDGE,LINK LINK BOLT HOLE CENTERLINE TO EDGE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AWXCJ 04SIZE FOR WHICH DESIGNED,CARTRIDGE CARTRIDGE SIZE FOR WHICH DESIGNED THE DESIGNATED SIZE OF THE CARTRIDGE FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AF47 AWXDJ 04DIAMETER,JAW JAW DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE JAW,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AWXED 19ARRANGEMENT,CYLINDER CYLINDER ARRANGEMENT THE ARRANGEMENT OF THE CYLINDERS. SELECT REPLY CODE 10AM47 AWXFJ 04LENGTH,STROKE STROKE LENGTH THE MEASURED DISTANCE OF THE STROKE. 1D AND 1B MODE REPLY11AA05 AWXGG /D/ 03DESIGNATOR,ELEMENT,TIME DELAY TIME DELAY ELEMENT DESIGNATOR A DESIGNATION ASSIGNED TO THE TIME DELAY ELEMENT FOR THE PURPOSE OF READY IDENTIFICATION. FULL TEXT WRITE-IN 0 AWXHJ 10AREA,TRANSFER,CONDENSER HEAT CONDENSER HEAT TRANSFER AREA THE AMOUNT OF HEAT TRANSFER AREA OF THE CONDENSER. 1D AND 1B MODE REPLY11AC51 AWXJJ 10CAPACITY,RECEIVER,SEPARATE LIQUID SEPARATE LIQUID RECEIVER CAPACITY A MEASUREMENT OF THE CAPACITY OF A SEPARATE LIQUID RECEIVER. 1D AND 1B MODE REPLY11AD42 AWXKJ 10CAPACITY,REFRIGERANT REFRIGERANT CAPACITY THE AMOUNT OF REFRIGERANT THE ITEM WILL HOLD. 1D AND 1B MODE REPLY12AG67 AWXLJ 10CAPACITY,MINIMUM MINIMUM CAPACITY THE MINIMUM CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY11AD42 AWXMB 10AMPS,MAXIMUM,LOCK TEST LOCK TEST MAXIMUM AMPS THE MAXIMUM AMOUNT OF AMPERES THE ITEM CAN WITHSTAND WITHOUT DESTRUCTION. 1B MODE REPLY 0 AWXNA 12QUANTITY,BRUSH BRUSH QUANTITY THE NUMBER OF BRUSHES INCLUDED WITH THE ITEM. 1A MODE REPLY 0 AWXPD 18TYPE,FIT,COMMUTATOR END MOUNTING COMMUTATOR END MOUNTING FIT TYPE INDICATES THE TYPE OF FIT PROVIDED FOR MOUNTING ON THE COMMUTATOR END. SELECT REPLY CODE 10AA78 AWXQJ A18TYPE AND QUANTITY,HOLE,MOUNTING,COMMUTATOR END COMMUTATOR END MOUNTING HOLE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF MOUNTING HOLES PROVIDED IN THE COMMUTATOR END. 1D AND 1A MODE REPLY12AA78 AWXSJ A19DOCUMENT,CODING,COLOR COLOR CODING DOCUMENT THE SPECIFICATION, STANDARD, DRAWING, OR SIMILAR INSTRUMENT THAT SPECIFIES THE INDIVIDUAL COLOR CODING UNDER WHICH THE ITEM IS IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER.INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT. 1D AND 1A MODE REPLY11AC28 AWXTJ /D/A19DATA,PRINTED,CIRCUIT IDENTIFICATION CIRCUIT IDENTIFICATION PRINTED DATA THE PRINTED DATA WHICH IDENTIFIES EACH CONDUCTOR WITH RESPECT TO THE ELECTRICAL SYSTEM OF WHICH IT IS TO FORM A PART. 1D AND 1A MODE REPLY13AJ91 AWXWJ /D/A19DOCUMENT,DATA,PRINTED,CIRCUIT IDENTIFICATION CIRCUIT IDENTIFICATION PRINTED DATA DOCUMENT THE SPECIFICATION,STANDARD,DRAWING OR SIMILAR INSTRUMENT THAT SPECIFIES THE INDIVIDUAL CIRCUIT IDENTIFICATION PRINTED DATA UNDER WHICH THE ITEM IS IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE FEDERAL SUPPLY CODE FOR MANUFACTURER (FSCM) OF THE ENTITY CONTROLLING THE INSTRUMENT. 1D AND 1A MODE REPLY11AC28 AWXXJ /D/A19NUMBER,REFERENCE,IDENTIFYING,CONDUCTOR MANUFACTURER CONDUCTOR MANUFACTURER IDENTIFYING REFERENCE NUMBER THE IDENTIFYING REFERENCE NUMBER ASSIGNED TO THE INDIVIDUAL CONDUCTOR BY THE MANUFACTURER,FOR CONTROLLING THE ITEM. 1D AND 1A MODE REPLY13AJ91 AWXYJ /D/A19CODE,MANUFACTURER,CONDUCTOR CONDUCTOR MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE CONDUCTOR. 1D AND 1A MODE REPLY13AJ91 AWXZH /D/ 18TYPE AND LOCATION,MATERIAL,COVERING,MULTICONDUCTOR GROUP MULTICONDUCTOR GROUP COVERING MATERIAL TYPE AND LOCATION INDICATES THE TYPE OF COVERING MATERIAL/S/ APPLIED OVER A MULTICONDUCTOR GROUPING WITHIN AN ARRANGEMENT TO PROVIDE MECHANICAL/ELECTRICAL PROTECTION AND CIRCUIT IDENTIFICATION,AND ITS LOCATION. 3D MODE REPLY 32AK896AD093AJ91 AWYAH /D/ 18TYPE AND MATERIAL,COVERING,PROTECTIVE,CABLE/CORD CABLE/CORD PROTECTIVE COVERING TYPE AND MATERIAL INDICATES THE CABLE/CORD PROTECIVE COVERING TYPE AND MATERIAL. 2D MODE REPLY 22AK896AD09 AWYBD /D/ 19FORM,SHIELD SHIELD FORM THE FABRICATED FORM OF THE SHIELDING PROVIDED. SELECT REPLY CODE 10AL59 AWYCJ /D/ 04LENGTH AND LOCATION,CONDUCTOR,INDIVIDUAL INDIVIDUAL CONDUCTOR LENGTH AND LOCATION A MEASUREMENT OF THE LONGEST DIMENSION OF THE INDIVIDUAL CONDUCTOR BETWEEN BUT NOT INCLUDING THE TERMINALS,IN DISTINCTION FROM WIDTH,AND THE LOCATION OF EACH CONDUCTOR. 3D AND 1B MODE REPLY31AA051AC203AJ91 AWYDJ T10RANGE,GAGE,PRESSURE,CYLINDER CYLINDER PRESSURE GAGE RANGE THE MINIMUM TO MAXIMUM PRESSURE AT WHICH THE CYLINDER PRESSURE GAGE WILL OPERATE. 1D AND 1F MODE REPLY12AG20 AWYEJ 10PRESSURE,DELIVERY,MAXIMUM MAXIMUM DELIVERY PRESSURE THE MAXIMUM PRESSURE AT WHICH THE ITEM WILL DELIVER. 1D AND 1B MODE REPLY12AG20 AWYFJ /D/ 10VOLTAGE RATING PER CONDUCTOR VOLTAGE RATING PER CONDUCTOR THE MAXIMUM SUSTAINED VOLTAGE PER CONDUCTOR THAT CAN SAFELY BE APPLIED WITHOUT RISKING THE POSSIBILITY OF BREAKDOWN. 2D AND 1B MODE REPLY22AH163AJ91 AWYGJ 10VOLTAGE RATING,NOMINAL NOMINAL VOLTAGE RATING THE NOMINAL VALUE(S) OF POTENTIAL FOR WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY11AB63 AWYHJ 10SETTING,PRESSURE,CLOSING CLOSING PRESSURE SETTING THE PRESSURE SETTING AT WHICH THE ITEM WILL CLOSE. 2D AND 1B MODE REPLY22AG201AC20 AWYJJ 04LENGTH,RETRACTED RETRACTED LENGTH THE MEASUREMENT OF THE LONGEST DIMENSION OF THE ITEM WHEN RETRACTED. 1D AND 1B MODE REPLY11AA05 AWYKJ /D/A18TYPE AND QUANTITY,FACILITY,ALIGNING,COMMUTATOR END MOUNTING COMMUTATOR END MOUNTING ALIGNING FACILITY TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF ALIGNING FACILITIES PROVIDED FOR COMMUTATOR END MOUNTING. 1D AND 1A MODE REPLY12AA78 AWYLD /D/ 07EAR,MOUNTING,COMMUTATOR END COMMUTATOR END MOUNTING EAR AN INDICATION OF WHETHER OR NOT THE COMMUTATOR END IS PROVIDED WITH MOUNTING EARS. SELECT REPLY CODE 10AB22 AWYMD /D/ 07OPENING,INSPECTION,COMMUTATOR END MOUNTING COMMUTATOR END MOUNTING INSPECTION OPENING AN INDICATION OF WHETHER OR NOT THE COMMUTATOR END IS PROVIDED WITH MOUNTING INSPECTION OPENINGS. SELECT REPLY CODE 10AB22 AWYNA 12QUANTITY,STUD,COMMUTATOR END MOUNTING COMMUTATOR END MOUNTING STUD QUANTITY THE NUMBER OF MOUNTING STUDS PROVIDED ON THE COMMUTATOR END. 1A MODE REPLY 0 AWYPD 18TYPE,FIT,DRIVE END MOUNTING DRIVE END MOUNTING FIT TYPE INDICATES THE TYPE OF FIT PROVIDED FOR MOUNTING THE DRIVE END. SELECT REPLY CODE 10AA78 AWYQJ A18TYPE AND QUANTITY,HOLE,MOUNTING,DRIVE END DRIVE END MOUNTING HOLE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF MOUNTING HOLES PROVIDED IN THE DRIVE END. 1D AND 1A MODE REPLY12AA78 AWYRJ A18TYPE AND QUANTITY,FACILITY,ALIGNING,DRIVE END MOUNTING DRIVE END MOUNTING ALIGNING FACILITY TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF ALIGNING FACILITIES PROVIDED FOR DRIVE END MOUNTING. 1D AND 1A MODE REPLY12AA78 AWYSD /D/ 07EAR,MOUNTING,DRIVE END DRIVE END MOUNTING EAR AN INDICATION OF WHETHER OR NOT THE DRIVE END IS PROVIDED WITH MOUNTING EARS. SELECT REPLY CODE 10AB22 AWYTD /D/ 07OPENING,INSPECTION,DRIVE END MOUNTING DRIVE END MOUNTING INSPECTION OPENING AN INDICATION OF WHETHER OR NOT THE DRIVE END IS PROVIDED WITH MOUNTING INSPECTION OPENINGS. SELECT REPLY CODE 10AB22 AWYWD /D/ 07FACILITIES,MOUNTING,EXTERNAL ATTACHMENT EXTERNAL ATTACHMENT MOUNTING FACILITIES AN INDICATION OF WHETHER OR NOT FACILITIES ARE PROVIDED FOR MOUNTING EXTERNAL ATTACHMENTS. SELECT REPLY CODE 10AB22 AWYXG /D/ 04SIZE,FACILITY,MOUNTING MOUNTING FACILITY SIZE DESIGNATES THE SIZE OF THE MOUNTING FACILITY. FULL TEXT WRITE-IN 0 AWYYD 18TYPE,BREAK,CONTACT CONTACT BREAK TYPE INDICATES THE TYPE OF CONTACT BREAK/S/ PROVIDED. SELECT REPLY CODE 10AJ27 AWYZD /D/ 07TERMINAL,CHOKE,AUTOMATIC AUTOMATIC CHOKE TERMINAL AN INDICATION OF WHETHER OR NOT AN AUTOMATIC CHOKE TERMINAL IS INCLUDED. SELECT REPLY CODE 10AA49 AWZAL /D/ 16STYLE,SHAPE,CROSS-SECTIONAL CROSS-SECTIONAL SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE CROSS-SECTIONAL SHAPE OF THE ITEM. 1L MODE REPLY 0 AWZBJ 10VOLTAGE RATING,CLOSING CLOSING VOLTAGE RATING THE VOLTAGE RATING AT WHICH THE ITEM WILL CLOSE. 2D AND 1B MODE REPLY21AB631AC20 AWZCD 19CHARACTERISTIC,CONNECTION,SUCTION SUCTION CONNECTION CHARACTERISTIC AN INDICATION OF THE SUCTION CONNECTION CHARACTERISTIC(S). SELECT REPLY CODE 10AJ93 AWZDD 18TYPE,CONNECTION,SUCTION SUCTION CONNECTION TYPE INDICATES THE TYPE OF SUCTION CONNECTION/S/ INTEGRAL WITH THE ITEM. SELECT REPLY CODE 10AA84 AWZEA 12QUANTITY,CONNECTION,SUCTION SUCTION CONNECTION QUANTITY THE NUMBER OF SUCTION CONNECTIONS FURNISHED. 1A MODE REPLY 0 AWZFA 19CODE,MANUFACTURER,ELECTRIC MOTOR ELECTRIC MOTOR MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE ELECTRIC MOTOR. 1A MODE REPLY 0 AWZGB 10RPM,MOTOR,ELECTRIC ELECTRIC MOTOR RPM THE SPEED OF THE ELECTRIC MOTOR,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 AWZHJ 10IMPEDANCE RATING IN OHMS IMPEDANCE RATING IN OHMS THE TOTAL OPPOSITION /RESISTIVE AND REACTIVE/ WHICH THE ITEM OFFERS TO THE FLOW OF ALTERNATING CURRENT,EXPRESSED IN OHMS. 2D AND 1B MODE REPLY21AG971AC20 AWZJD 19SOURCE,POWER POWER SOURCE THE SOURCE OF POWER WHICH PROVIDES THE ENERGY REQUIRED FOR THE OPERATION OF THE ITEM. SELECT REPLY CODE 10AG27 AWZKD /D/ 07PUMP,PRIMER PRIMER PUMP AN INDICATION OF WHETHER OR NOT A PRIMER PUMP IS INCLUDED. SELECT REPLY CODE 10AA49 AWZLH /D/ 18TYPE PER SPECIFIED DOCUMENT,INCLOSURE,ELECTRIC MOTOR ELECTRIC MOTOR INCLOSURE TYPE PER SPECIFIED DOCUMENT INDICATES THE TYPE OF INCLOSURE PROVIDED TO COAT,COVER,PROTECT,OR ENCASE THE ELECTRIC MOTOR PER SPECIFIED DOCUMENT. 2D MODE REPLY 22AA652AM46 AWZMD /D/ 07ELIMINATOR,AIR AIR ELIMINATOR AN INDICATION OF WHETHER OR NOT AN AIR ELIMINATOR IS INCLUDED. SELECT REPLY CODE 10AA49 AWZND /D/ 07AMPLIFIER,MAGNETIC MAGNETIC AMPLIFIER AN INDICATION OF WHETHER OR NOT A MAGNETIC AMPLIFIER/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 AWZPA 12QUANTITY,SPEED,OPERATING OPERATING SPEED QUANTITY THE NUMBER OF OPERATING SPEEDS PROVIDED. 1A MODE REPLY 0 AWZQD /D/ 07HOSE HOSE AN INDICATION OF WHETHER OR NOT A HOSE IS INCLUDED. SELECT REPLY CODE 10AA49 AWZRJ 04LENGTH,HOSE,INLET INLET HOSE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE INLET HOSE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AWZSJ 04DIAMETER,HOSE,INLET INLET HOSE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INLET HOSE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AWZTJ 04LENGTH,HOSE,OUTLET OUTLET HOSE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE OUTLET HOSE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AWZWJ 04DIAMETER,HOSE,OUTLET OUTLET HOSE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTLET HOSE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AWZXD 18TYPE,CONNECTION,OUTLET END OUTLET END CONNECTION TYPE INDICATES THE TYPE OF OUTLET END CONNECTION. SELECT REPLY CODE 10AB76 AWZYD 18TYPE,CONNECTION,END END CONNECTION TYPE INDICATES THE TYPE OF END CONNECTION. SELECT REPLY CODE 10AB76 AWZZA 13THREAD SIZE,CONNECTION,END END CONNECTION THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE END CONNECTION. 1A MODE REPLY 0 AXAAD 13THREAD SERIES DESIGNATOR,CONNECTION,END END CONNECTION THREAD SERIES DESIGNATOR A DESIGNATOR INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF THE END CONNECTION. SELECT REPLY CODE 10AH06 AXABD 13THREAD LOCATION,CONNECTION,END END CONNECTION THREAD LOCATION THE LOCATION OF THE THREADS ON THE END CONNECTION. SELECT REPLY CODE 10AJ91 AXACD 19CONSTRUCTION,HOLDER,FOOT FOOT HOLDER CONSTRUCTION AN INDICATION OF THE STRUCTURAL FORM OF THE FOOT HOLDER. SELECT REPLY CODE 10AL59 AXADD /D/ 07HANDLE,FOLDING FOLDING HANDLE AN INDICATION OF WHETHER OR NOT A FOLDING HANDLE IS INCLUDED. SELECT REPLY CODE 10AA49 AXAEJ 04SIZE SIZE DESIGNATES THE SIZE OF THE TOTAL SURFACE OF AN ITEM. 1D AND 1B MODE REPLY11AA05 AXAFD 18TYPE,PRESSURE PRESSURE TYPE INDICATES THE TYPE OF PRESSURE. SELECT REPLY CODE 10AL77 AXAGG 10PRESSURE RATING AT MAXIMUM TEMP,WORKING,INLET INLET WORKING PRESSURE RATING AT MAXIMUM TEMP THE RATED INLET WORKING PRESSURE AT MAXIMUM TEMPERATURE AT WHICH THE ITEM IS DESIGNED TO OPERATE. FULL TEXT WRITE-IN 0 AXAHJ 10CAPACITY RATING,STEAM,SATURATED SATURATED STEAM CAPACITY RATING THE RATED CAPACITY OF SATURATED STEAM FOR WHICH AN ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AC64 AXAJJ /D/T10RANGE,PRESSURE,ACTUATING FLUID ACTUATING FLUID PRESSURE RANGE THE MINIMUM TO MAXIMUM ACTUATING FLUID PRESSURE AT WHICH AN ITEM IS DESIGNED TO OPERATE. 1D AND 1F MODE REPLY12AB16 AXAKD /D/ 07FEATURE,BODY,ANGLE ANGLE BODY FEATURE AN INDICATION OF WHETHER OR NOT AN ANGLE BODY FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AXALD 07SIMILARITY,CONNECTION,END END CONNECTION SIMILARITY AN INDICATION OF WHETHER OR NOT THE END CONNECTIONS ARE IDENTICAL. SELECT REPLY CODE 10AA37 AXAMD /D/ 18TYPE,CONNECTION,END END CONNECTION TYPE INDICATES THE TYPE OF END CONNECTION. SELECT REPLY CODE 10AB76 AXANG /D/ 04SIZE,NOMINAL,PIPE/TUBE PIPE/TUBE NOMINAL SIZE DESIGNATES THE NOMINAL SIZE,SUCH AS LENGTH,WIDTH,DIAMETER,AND THE LIKE,OF THE PIPE AND/OR TUBE. FULL TEXT WRITE-IN 0 AXAPD /D/ 07FEATURE,FACE,RAISED,FLANGE FLANGE RAISED FACE FEATURE AN INDICATION OF WHETHER OR NOT A FLANGE RAISED FACE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AXAQA 12QUANTITY,HOLE,FLANGE BOLT FLANGE BOLT HOLE QUANTITY THE NUMBER OF BOLT HOLES IN THE FLANGE. 1A MODE REPLY 0 AXARG 04SPACING,HOLE,FLANGE BOLT FLANGE BOLT HOLE SPACING THE SPACING OF THE FLANGE BOLT HOLE/S/. FULL TEXT WRITE-IN 0 AXASJ 10CAPACITY PER STROKE,LUBRICANT LUBRICANT CAPACITY PER STROKE THE VALUE WHICH REFLECTS THE CAPACITY OF THE LUBRICANT AN ITEM IS DESIGNED TO ACCOMMODATE PER STROKE. 1D AND 1B MODE REPLY11AB10 AXATJ 10CAPACITY,LUBRICANT LUBRICANT CAPACITY THE VALUE WHICH REFLECTS THE CAPACITY OF THE LUBRICANT AN ITEM IS DESIGNED TO ACCOMMODATE. 2D AND 1B MODE REPLY22AG671AC20 AXAWJ 10CAPACITY,PRESSURE PRESSURE CAPACITY THE MEASURED PRESSURE CAPACITY FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY21AB181AC20 AXAXB 10CAPACITY IN AMPS,CARRYING,CURRENT CURRENT CARRYING CAPACITY IN AMPS THE CURRENT CAPABLE OF BEING CARRIED INDEFINITELY BY A WIRE,EXPRESSED IN AMPERES. 1B MODE REPLY 0 AXAYJ 10VOLTAGE RATING,OPENING OPENING VOLTAGE RATING THE VOLTAGE RATING AT WHICH THE ITEM WILL OPEN. 2D AND 1B MODE REPLY21AB631AC20 AXAZJ 10CURRENT,PULL-IN PULL-IN CURRENT THE AMOUNT OF CURRENT REQUIRED TO ACTIVATE THE ITEM. 2D AND 1B MODE REPLY21AC301AC20 AXBAJ 10CURRENT,HOLD-IN HOLD-IN CURRENT THE AMOUNT OF CURRENT REQUIRED TO MAINTAIN OPERATION OF THE ITEM. 2D AND 1B MODE REPLY21AC301AC20 AXBBJ /D/ 04LENGTH,RATED,CURRENT CURRENT RATED LENGTH THE SPECIFIED CURRENT RATED LENGTH. 1D AND 1B MODE REPLY11AA05 AXBCJ /D/ 04LENGTH ACCOMMODATED,WIRE,SPECIAL HANDLING DEVICE SPECIAL HANDLING DEVICE WIRE LENGTH ACCOMMODATED A MEASUREMENT OF THE LONGEST DIMENSION OF WIRE THE SPECIAL HANDLING DEVICE FURNISHED WILL ACCOMMODATE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY12AG67 AXBDJ 04LENGTH,STROKE,PLUNGER PLUNGER STROKE LENGTH THE MEASURED DISTANCE OF THE PLUNGER STROKE. 2D AND 1B MODE REPLY21AA051AC20 AXBED /D/ 07LINKAGE,ENGAGING ENGAGING LINKAGE AN INDICATION OF WHETHER OR NOT ENGAGING LINKAGE IS INCLUDED. SELECT REPLY CODE 10AA49 AXBFH /D/ 18TYPE AND LOCATION,TERMINATION TERMINATION TYPE AND LOCATION INDICATES THE TYPE OF TERMINATION AND ITS LOCATION. 3D MODE REPLY 32AM482AE793AJ91 AXBGD 07ADJUSTABILITY,LINKAGE LINKAGE ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE LINKAGE IS ADJUSTABLE. SELECT REPLY CODE 10AB00 AXBHD 18TYPE,CONNECTION,LINKAGE SHIFT LEVER LINKAGE SHIFT LEVER CONNECTION TYPE INDICATES THE TYPE OF SHIFT LEVER CONNECTION PROVIDED WITH THE LINKAGE. SELECT REPLY CODE 10AB76 AXBJJ /D/ 04SIZE AND LOCATION,MOUNTING,TERMINAL LUG TERMINAL LUG MOUNTING SIZE AND LOCATION DESIGNATES THE SIZE OF THE MOUNTING ACCOMMODATION PROVIDED IN THE TERMINAL LUG,AND ITS LOCATION. 3D AND 1B MODE REPLY31AA052AM483AJ91 AXBKJ /D/A16STYLE AND LOCATION,TERMINAL TERMINAL STYLE AND LOCATION THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE TERMINAL TYPE PROVIDED ON THE ITEM,AND ITS LOCATION. 2D AND 1A MODE REPLY22AM483AJ91 AXBLH /D/ 19POLARITY AND LOCATION,TERMINAL,BATTERY BATTERY TERMINAL POLARITY AND LOCATION THE POLARITY OF THE TERMINAL AS DETERMINED BY THE POLARITY OF THE BATTERY POST ACCOMMODATED,AND ITS LOCATION. 2D MODE REPLY 21AK223AJ91 AXBMJ /D/A19NUMBER AND LOCATION,REFERENCE,IDENTIFYING,TERMINAL MANUFACTURER TERMINAL MANUFACTURER IDENTIFYING REFERENCE NUMBER AND LOCATION THE IDENTIFYING REFERENCE NUMBER ASSIGNED TO THE TERMINAL/S/ BY THE MANUFACTURER,FOR CONTROLLING THE ITEM,AND ITS LOCATION. 2D AND 1A MODE REPLY22AM483AJ91 AXBNJ /D/A19CODE AND LOCATION,MANUFACTURER,FEDERAL,TERMINAL TERMINAL FEDERAL MANUFACTURER CODE AND LOCATION THE FEDERAL MANUFACTURER CODE NUMBER ASSIGNED TO THE MANUFACTURER OF EACH TERMINAL FOR CONTROLLING THE ITEM,AND ITS LOCATION. 2D AND 1A MODE REPLY22AM483AJ91 AXBPJ /D/ 04LENGTH AND LOCATION,CONDUCTOR CONDUCTOR LENGTH AND LOCATION A MEASUREMENT OF THE LONGEST DIMENSION OF AN INDIVIDUAL CONDUCTOR,AND ITS LOCATION. 4D AND 1B MODE REPLY41AA051AC202AM483AJ91 AXBQJ 04LENGTH,OVERALL,LEAD LEAD OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE LEAD. 2D AND 1B MODE REPLY21AA051AC20 AXBRJ /D/ 04LENGTH,LEAD,RETRACTILE RETRACTILE LEAD LENGTH A MEASUREMENT OF THE LONGEST END TO END DIMENSION,INCLUDING TERMINATIONS OF A RETRACTILE LEAD IN ITS RETRACTED POSITION. 2D AND 1B MODE REPLY21AA051AC20 AXBSJ /D/A16STYLE AND LOCATION,RELIEF,STRAIN STRAIN RELIEF STYLE AND LOCATION THE STYLE DESIGNATION INDICATING THE METHOD BY WHICH STRESS OR STRAIN IS RELIEVED,AND ITS LOCATION. 2D AND 1A MODE REPLY22AM483AJ91 AXBTJ /D/ 04DISTANCE BETWEEN TERMINAL HOLES AND LOCATION,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN TERMINAL HOLES AND LOCATION THE DISTANCE MEASURED FROM THE CENTER OF THE FIRST TERMINAL HOLE TO THE CENTER OF THE SECOND TERMINAL HOLE AND THE LOCATION. 3D AND 1B MODE REPLY31AA051AC203AJ91 AXBWJ /D/ 10STRENGTH,PULL,LEAD LEAD PULL STRENGTH THE PULLING FORCE WHICH THE ITEM IS CAPABLE OF WITHSTANDING WITHOUT ANY PERMANENT DEFORMATION OR DAMAGE. 1D AND 1B MODE REPLY12AB16 AXBXJ /D/A18TYPE FOR WHICH DESIGNED,HOLDER HOLDER TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF HOLDER FOR WHICH THE ITEM IS DESIGNED. 1D AND 1A MODE REPLY12AE98 AXBYA /D/ 13THREAD SIZE,HOLE,THREADED,ACCOMMODATED LINKAGE ACCOMMODATED LINKAGE THREADED HOLE THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE ACCOMMODATED LINKAGE THREADED HOLE. 1A MODE REPLY 0 AXBZD /D/ 07FEATURE,STACKABILITY,REEL REEL STACKABILITY FEATURE AN INDICATION OF WHETHER OR NOT A REEL STACKABILITY FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AXCAJ 04DIAMETER,HOLE,UNTHREADED,ACCOMMODATED LINKAGE ACCOMMODATED LINKAGE UNTHREADED HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE UNTHREADED HOLE FOR THE ACCOMMODATED LINKAGE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AXCBD /D/ 19MARKING,ASSEMBLY ASSEMBLY MARKING AN INDICATION OF THE MARKINGS ON THE ASSEMBLY. SELECT REPLY CODE 10AM51 AXCCD /D/ 07PROVISION,CLOSING,MANUAL,CONTACT CONTACT MANUAL CLOSING PROVISION AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES PROVISIONS FOR MANUALLY CLOSING THE CONTACTS. SELECT REPLY CODE 10AA49 AXCDA 12QUANTITY,TERMINAL,CONTROL CONTROL TERMINAL QUANTITY THE NUMBER OF CONTROL TERMINALS PROVIDED. 1A MODE REPLY 0 AXCED 18TYPE,TERMINAL,CONTROL CONTROL TERMINAL TYPE INDICATES THE TYPE OF CONTROL TERMINAL/S/ PROVIDED. SELECT REPLY CODE 10AA58 AXCFD /D/ 07TERMINAL,CONTROL,GROUNDED GROUNDED CONTROL TERMINAL AN INDICATION OF WHETHER OR NOT A GROUNDED CONTROL TERMINAL IS INCLUDED. SELECT REPLY CODE 10AA49 AXCGB /D/ 10CONDUCTIVITY,PERCENT,MATERIAL MATERIAL PERCENT CONDUCTIVITY THE DIRECT CURRENT CONDUCTANCE OF A MATERIAL,EXPRESSED AS A PERCENT OF THE CONDUCTIVITY OF COPPER. 1B MODE REPLY 0 AXCHJ /D/T10RANGE PER SECTION IN PICOFARADS,CAPACITANCE CAPACITANCE RANGE PER SECTION IN PICOFARADS THE MINIMUM AND MAXIMUM VALUES OF ELECTRICAL CHARGE PER SECTION,EXPRESSED IN PICOFARADS. 1D AND 1F MODE REPLY13AJ91 AXCJJ /D/T10CAPACITANCE CHANGE PER SECTION IN PERCENT AT MINIMUM OPERATING TEMP FROM 25 DEG CELSIUS CAPACITANCE CHANGE PER SECTION IN PERCENT AT MINIMUM OPERATING TEMP FROM 25 DEG CELSIUS THE LIMITS OF CAPACITANCE CHANGE PER SECTIONIN PERCENT AT MINIMUM OPERATING TEMPERATURE FROM A STATED VALUE AT 25 DEG CELSIUS. 1D AND 1F MODE REPLY13AJ91 AXCKJ /D/T10CAPACITANCE CHANGE PER SECTION IN PERCENT AT MAXIMUM OPERATING TEMP FROM 25 DEG CELSIUS CAPACITANCE CHANGE PER SECTION IN PERCENT AT MAXIMUM OPERATING TEMP FROM 25 DEG CELSIUS THE LIMITS OF CAPACITANCE CHANGE PER SECTION IN PERCENT AT MAXIMUM OPERATING TEMPERATURE FROM A STATED VALUE AT 25 DEG CELSIUS. 1D AND 1F MODE REPLY13AJ91 AXCLJ /D/ 10CAPACITANCE DRIFT PER SECTION IN PICOFARADS CAPACITANCE DRIFT PER SECTION IN PICOFARADS THE DRIFT OF CAPACITANCE PER SECTION,EXPRESSED IN PICOFARADS. 1D AND 1B MODE REPLY13AJ91 AXCMD 19CHARACTERISTIC,TUNING TUNING CHARACTERISTIC THE TUNING CHARACTERISTIC OF THE ITEM. SELECT REPLY CODE 10AM52 AXCND 18TYPE,PLATE,ROTARY,SPLIT-STATOR SPLIT-STATOR ROTARY PLATE TYPE INDICATES THE TYPE OF SPLIT-STATOR ROTARY PLATE PROVIDED. SELECT REPLY CODE 10AM16 AXCPD 18TYPE,WINDING WINDING TYPE INDICATES THE SPECIFIC ARRANGEMENT IN WHICH WIRE IS WOUND ON A FORM OR IS FORMED BY WINDING. SELECT REPLY CODE 10AC02 AXCQA 10STROKES PER CYCLE STROKES PER CYCLE THE NUMBER OF STROKES REQUIRED TO COMPLETE ONE CYCLE. 1A MODE REPLY 0 AXCRD /D/ 07WIRE,FIRING FIRING WIRE AN INDICATION OF WHETHER OR NOT A FIRING WIRE IS INCLUDED. SELECT REPLY CODE 10AA49 AXCSD /D/ 19ARRANGEMENT,MOUNTING,PRIME MOVER PRIME MOVER MOUNTING ARRANGEMENT AN INDICATION OF THE MOUNTING ARRANGEMENT OF THE PRIME MOVERS. SELECT REPLY CODE 10AB21 AXCTJ 04LENGTH,WIRE WIRE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE WIRE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AXCWG /D/ 10HORSEPOWER AT SPECIFIED RPM,BRAKE BRAKE HORSEPOWER AT SPECIFIED RPM THE POWER DELIVERED BY THE ITEM AT SPECIFIED REVOLUTIONS PER MINUTE. FULL TEXT WRITE-IN 0 AXCXG /D/ 10HORSEPOWER AT SPECIFIED RPM,BRAKE,COMMON OUTPUT SHAFT COMMON OUTPUT SHAFT BRAKE HORSEPOWER AT SPECIFIED RPM THE POWER DELIVERED BY THE COMMON OUTPUT SHAFT AT SPECIFIED REVOLUTIONS PER MINUTE. FULL TEXT WRITE-IN 0 AXCYA 03DESIGNATION,SIZE,AWG AWG SIZE DESIGNATION A DESIGNATION INDICATING THE AMERICAN WIRE GAGE SIZE BY WHICH THE ITEM IS KNOWN AND/OR IDENTIFIED. 1A MODE REPLY 0 AXCZD /D/ 07FEATURE,COOLING,DIRECT RAW WATER DIRECT RAW WATER COOLING FEATURE AN INDICATION OF WHETHER OR NOT A DIRECT RAW WATER COOLING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AXDAD /D/ 07FEATURE,COOLING,CLOSED SYSTEM HULL CLOSED SYSTEM HULL COOLING FEATURE AN INDICATION OF WHETHER OR NOT A CLOSED SYSTEM HULL COOLING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AXDBD 18TYPE,HEAD,CYLINDER CYLINDER HEAD TYPE INDICATES THE TYPE OF CYLINDER HEAD PROVIDED. SELECT REPLY CODE 10AM49 AXDCD 18TYPE,FLANGE,COAXIAL LINE COAXIAL LINE FLANGE TYPE INDICATES THE TYPE OF COAXIAL LINE FLANGE PROVIDED. SELECT REPLY CODE 10AK54 AXDDD 18TYPE,ACTION,PISTON PISTON ACTION TYPE INDICATES THE TYPE OF PISTON ACTION PROVIDED. SELECT REPLY CODE 10AA79 AXDED 18TYPE,INDUCTION,FUEL FUEL INDUCTION TYPE THE MEANS BY WHICH THE FUEL IS INDUCTED INTO THE CYLINDER. SELECT REPLY CODE 10AM50 AXDFD /D/ 07FEATURE,USAGE,MULTIFUEL MULTIFUEL USAGE FEATURE AN INDICATION OF WHETHER OR NOT A MULTIFUEL USAGE FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 AXDHD 18TYPE,IGNITION IGNITION TYPE INDICATES THE TYPE OF IGNITION UTILIZED BY THE ITEM. SELECT REPLY CODE 10AJ53 AXDJD /D/ 07SYSTEM,IGNITION,DUAL DUAL IGNITION SYSTEM AN INDICATION OF WHETHER OR NOT A DUAL IGNITION SYSTEM IS INCLUDED. SELECT REPLY CODE 10AA49 AXDKD 05DIRECTION,ROTATION,CRANKSHAFT CRANKSHAFT ROTATION DIRECTION THE CRANKSHAFT ROTATION DIRECTION VIEWED FROM AND FACING THE MAIN DRIVING END. SELECT REPLY CODE 10AB50 AXDLD 05DIRECTION,ROTATION,COMMON OUTPUT SHAFT COMMON OUTPUT SHAFT ROTATION DIRECTION THE ROTATION DIRECTION OF THE COMMON OUTPUT SHAFT VIEWED FROM AND FACING THE SHAFT END. SELECT REPLY CODE 10AB50 AXDMG 03DESIGNATOR,CARTRIDGE CARTRIDGE DESIGNATOR A DESIGNATION ASSIGNED TO THE CARTRIDGE FOR THE PURPOSE OF READY IDENTIFICATION. FULL TEXT WRITE-IN 0 AXDND /D/ 07FEATURE,REVERSIBLE,DIRECT DIRECT REVERSIBLE FEATURE AN INDICATION OF WHETHER OR NOT A DIRECT REVERSIBLE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AXDPD 11METHOD,STARTING STARTING METHOD THE MEANS USED TO START THE ITEM. SELECT REPLY CODE 10AC58 AXDQD /D/ 18TYPE,SYSTEM,HYDRAULIC STARTER PUMP HYDRAULIC STARTER PUMP SYSTEM TYPE INDICATES THE TYPE OF PUMPING SYSTEM UTILIZED BY THE HYDRAULIC STARTER. SELECT REPLY CODE 10AC58 AXDRD /D/ 07SUPERCHARGER SUPERCHARGER AN INDICATION OF WHETHER OR NOT A SUPERCHARGER IS INCLUDED. SELECT REPLY CODE 10AA49 AXDSD /D/ 07FLYWHEEL FLYWHEEL AN INDICATION OF WHETHER OR NOT A FLYWHEEL IS INCLUDED. SELECT REPLY CODE 10AA49 AXDTD /D/ 07HOUSING,FLYWHEEL FLYWHEEL HOUSING AN INDICATION OF WHETHER OR NOT THE FLYWHEEL HOUSING IS INCLUDED. SELECT REPLY CODE 10AA49 AXDWD /D/ 07GEAR,REDUCTION REDUCTION GEAR AN INDICATION OF WHETHER OR NOT A REDUCTION GEAR IS INCLUDED. SELECT REPLY CODE 10AA49 AXDXA /D/ 12QUANTITY PER REGISTER,DRUM,FIXED FIXED DRUM QUANTITY PER REGISTER THE NUMBER OF FIXED DRUMS PER REGISTER. 1A MODE REPLY 0 AXDYA /D/ 12QUANTITY PER FIXED DRUM,ROW,FIGURE FIGURE ROW QUANTITY PER FIXED DRUM THE NUMBER OF ROWS OF FIGURES CONTAINED ON EACH FIXED DRUM. 1A MODE REPLY 0 AXDZA /D/ 10VALUE,INCREMENT INCREMENT VALUE THE FIXED NUMERIC VALUE/S/ BY WHICH THE ITEM COUNTS. 1A MODE REPLY 0 AXEAB 10INCREMENT INDICATED,SMALLEST SMALLEST INCREMENT INDICATED THE SMALLEST NUMERIC FIGURE THE ITEM WILL REGISTER. 1B MODE REPLY 0 AXEBG 19NUMBER,IDENTIFYING IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE ITEM. FULL TEXT WRITE-IN 0 AXECH 11METHOD,RESET,REGISTER REGISTER RESET METHOD THE MEANS USED TO RETURN THE REGISTER/S/ TO ORIGINAL POSITION. 2D MODE REPLY 23AJ124AC58 AXEDD 19FUNCTION,REGISTER REGISTER FUNCTION THE MATHEMATICAL FUNCTION THE REGISTER/S/ IS DESIGNED TO PERFORM. SELECT REPLY CODE 10AM53 AXEED /D/ 18TYPE,DEVICE,REGISTER ACTUATION REGISTER ACTUATION DEVICE TYPE INDICATES THE TYPE OF DEVICE THAT ACTUATES THE REGISTER. SELECT REPLY CODE 10AE10 AXEFJ 04DISTANCE,TRAVEL,PISTON PISTON TRAVEL DISTANCE THE TRAVEL DISTANCE OF THE PISTON. 2D AND 1B MODE REPLY21AA051AC20 AXEGD /D/ 08LOCATION,DEVICE,ACTUATING ACTUATING DEVICE LOCATION INDICATES THE LOCATION OF THE ACTUATING DEVICE ON THE ITEM. SELECT REPLY CODE 10AJ91 AXEHD /D/ 07LOAD,EXPLOSIVE EXPLOSIVE LOAD AN INDICATION OF WHETHER OR NOT AN EXPLOSIVE LOAD IS INCLUDED. SELECT REPLY CODE 10AA49 AXEKD /D/ 07ACTUATOR ACTUATOR AN INDICATION OF WHETHER OR NOT AN ACTUATOR IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AXELD /D/ 18TYPE,PUMP PUMP TYPE INDICATES THE TYPE OF PUMP PROVIDED. PLEASE USE MRC BRJK IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA80 AXEMJ /D/ 10CAPACITY,CONTAINER CONTAINER CAPACITY THE RATED CAPACITY OF THE CONTAINER. 1D AND 1B MODE REPLY11AB18 AXEND 18TYPE,OPENING OPENING TYPE INDICATES THE TYPE OF OPENING PROVIDED IN THE ITEM. SELECT REPLY CODE 10AF88 AXEPD 18TYPE,COUPLER COUPLER TYPE INDICATES THE TYPE OF COUPLER PROVIDED. SELECT REPLY CODE 10AH98 AXEQD /D/ 07COVER,LEAKPROOF LEAKPROOF COVER AN INDICATION OF WHETHER OR NOT A LEAKPROOF COVER IS INCLUDED. SELECT REPLY CODE 10AA49 AXERD /D/ 07PLATE,FOLLOWER FOLLOWER PLATE AN INDICATION OF WHETHER OR NOT A FOLLOWER PLATE IS INCLUDED. SELECT REPLY CODE 10AA49 AXESD /D/ 07GUN,GREASE GREASE GUN AN INDICATION OF WHETHER OR NOT A GREASE GUN IS INCLUDED. SELECT REPLY CODE 10AA49 AXETD /D/ 07BRACKET,HOLDING,GREASE GUN GREASE GUN HOLDING BRACKET AN INDICATION OF WHETHER OR NOT A GREASE GUN HOLDING BRACKET IS INCLUDED. SELECT REPLY CODE 10AA49 AXEWD /D/ 07FITTING,LOADER,GREASE GUN GREASE GUN LOADER FITTING AN INDICATION OF WHETHER OR NOT A GREASE GUN LOADER FITTING IS INCLUDED. SELECT REPLY CODE 10AA49 AXEXH /D/ 18TYPE AND LOCATION,CONNECTOR,PRESSURE PRESSURE CONNECTOR TYPE AND LOCATION INDICATES THE PRESSURE CONNECTOR TYPE,AND ITS LOCATION. 2D MODE REPLY 22AG233AJ57 AXEYH /D/ 18TYPE AND LOCATION,CONNECTOR,TUBING END TUBING END CONNECTOR TYPE AND LOCATION INDICATES THE TUBING END CONNECTOR TYPE,AND ITS LOCATION. 2D MODE REPLY 22AG233AJ57 AXEZD /D/ 07METER,LUBRICANT LUBRICANT METER AN INDICATION OF WHETHER OR NOT A LUBRICANT METER IS INCLUDED. SELECT REPLY CODE 10AA49 AXFAJ 10CAPACITY PER MINUTE,DISPENSING,LUBRICANT LUBRICANT DISPENSING CAPACITY PER MINUTE THE VALUE WHICH REFLECTS THE LUBRICANT DISPENSING CAPACITY OF AN ITEM,EXPRESSED PER MINUTE. 1D AND 1B MODE REPLY11AB18 AXFBG 10PRESSURE RATING AT SPECIFIED TEMP RANGE,WORKING,MAXIMUM MAXIMUM WORKING PRESSURE RATING AT SPECIFIED TEMP RANGE THE MAXIMUM RATED WORKING PRESSURE OF AN ITEM AT A SPECIFIED TEMPERATURE RANGE. FULL TEXT WRITE-IN 0 AXFCD 02DESIGN,CONNECTION CONNECTION DESIGN THE DESIGN OF THE CONNECTION. SELECT REPLY CODE 10AD07 AXFDA 13THREAD SIZE,HOLE,BOLT BOLT HOLE THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE BOLT HOLE. 1A MODE REPLY 0 AXFEJ 04HEIGHT,KEY KEY HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A KEY,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AXFGB 04ANGLE IN DEG,PRESSURE,SPLINE SPLINE PRESSURE ANGLE IN DEG THE PRESSURE ANGLE OF THE SPLINE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AXFHJ 04LENGTH,SPLINE SPLINE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SPLINE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AXFJJ /D/ 04LENGTH,END,SQUARE SQUARE END LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SQUARE END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AXFKJ 04LENGTH,TONGUE TONGUE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A TONGUE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AXFLA 04SIZE ACCOMMODATED,KEY,SAE SAE KEY SIZE ACCOMMODATED THE SOCIETY OF AUTOMOTIVE ENGINEERS KEY SIZE DESIGNATION THAT AN ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 AXFMA /D/ 19STANDARD,GOVERNMENT,DRIVE SHAFT DRIVE SHAFT GOVERNMENT STANDARD THE GOVERNMENT STANDARD THAT COVERS THE DRIVE SHAFT. 1A MODE REPLY 0 AXFNA 19STANDARD,GOVERNMENT,MOUNTING MOUNTING GOVERNMENT STANDARD THE GOVERNMENT STANDARD THAT COVERS THE MOUNTING. 1A MODE REPLY 0 AXFPD 18TYPE,DISPLACEMENT DISPLACEMENT TYPE INDICATES THE DISPLACEMENT TYPE. SELECT REPLY CODE 10AL77 AXFQJ 10DISPLACEMENT PER REVOLUTION,CONSTANT CONSTANT DISPLACEMENT PER REVOLUTION AN INDICATION OF THE CONSTANT DISPLACEMENT PER REVOLUTION. 1D AND 1B MODE REPLY11AD42 AXFRD 03DESIGNATION,SIZE,FINISHED FINISHED SIZE DESIGNATION THE FINISHED SIZE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND DESIGNATED. SELECT REPLY CODE 10AE25 AXFSJ 10OVERSIZE OVERSIZE THE MEASURED AMOUNT OF THE OVERSIZE. 2D AND 1B MODE REPLY21AA051AC20 AXFTD /D/ 18TYPE,SKIRT SKIRT TYPE INDICATES THE TYPE OF SKIRT INCLUDED ON THE ITEM. SELECT REPLY CODE 10AE98 AXFWJ 04DEPTH,CUT CUT DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF A CUT,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AXFXD /D/ 07FEATURE,CUTAWAY,SKIRT BOTTOM SKIRT BOTTOM CUTAWAY FEATURE AN INDICATION OF WHETHER OR NOT A SKIRT BOTTOM CUTAWAY FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AXFYA /D/ 16STYLE,SLOT,SKIRT SKIRT SLOT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SKIRT SLOT. 1A MODE REPLY 0 AXFZA 12QUANTITY,GROOVE,RING RING GROOVE QUANTITY THE NUMBER OF RING GROOVES INCLUDED ON THE ITEM. 1A MODE REPLY 0 AXGAG 19POSITION,GROOVE,RING RING GROOVE POSITION A NUMBER INDICATING THE POSITION(S) OF THE RING GROOVE(S). FULL TEXT WRITE-IN 0 AXGBJ 04WIDTH,GROOVE,RING RING GROOVE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A RING GROOVE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AXGCG 04ANGLE,TAPER,GROOVE GROOVE TAPER ANGLE THE ANGLE OF A TAPERED GROOVE. FULL TEXT WRITE-IN 0 AXGDJ 04DIAMETER,GROOVE,RING RING GROOVE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A RING GROOVE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AXGEG /D/ 19POSITION BELOW PISTON PIN,GROOVE,RING RING GROOVE POSITION BELOW PISTON PIN THE BELOW PISTON PIN RING GROOVE POSITION ON THE ITEM. FULL TEXT WRITE-IN 0 AXGFD 02DESIGN,STAGE,AHEAD AHEAD STAGE DESIGN THE TERM USED TO DESCRIBE THE AHEAD (FORWARD) STAGE DESIGN OF THE ITEM. SELECT REPLY CODE 10AM57 AXGGJ /D/ 10VOLTAGE RATING,COIL COIL VOLTAGE RATING THE VALUE(S) OF POTENTIAL FOR WHICH THE COIL IS RATED. 2D AND 1B MODE REPLY21AB631AC20 AXGHJ 10CAPACITANCE IN PICOFARADS,NOMINAL NOMINAL CAPACITANCE IN PICOFARADS THE PROPERTY OF A SYSTEM OF CONDUCTORS AND DIELECTRICS WHICH PERMITS THE STORAGE OF ELECTRICITY WHEN POTENTIAL DIFFERENCE EXISTS BETWEEN THE CONDUCTORS,EXPRESSED IN PICOFARADS. 1D AND 1B MODE REPLY11AB39 AXGJJ 10ROTATION,DEVICE,ADJUSTMENT ADJUSTMENT DEVICE ROTATION THE MEASUREMENT OF THE MECHANICAL MOTION OF THE ADJUSTMENT DEVICE. 3D AND 1B MODE REPLY32AG671AC201AC84 AXGKH /D/ 01COLOR PER CONDUCTOR,BODY,BASIC BASIC BODY COLOR PER CONDUCTOR THE COLOR APPLIED TO THE PRIMARY INSULATION OF THE INDIVIDUAL CONDUCTOR/S/. 2D MODE REPLY 26AD063AJ91 AXGLH /D/ 01COLOR PER CONDUCTOR,TRACER,SECOND SECOND TRACER COLOR PER CONDUCTOR THE SECOND TRACER COLOR PER CONDUCTOR APPLIED TO THE BASIC BODY COLOR FOR IDENTIFICATION PURPOSES. 2D MODE REPLY 26AD063AJ91 AXGMH /D/ 01COLOR PER CONDUCTOR,TRACER,FIRST FIRST TRACER COLOR PER CONDUCTOR THE FIRST TRACER COLOR PER CONDUCTOR APPLIED TO THE BASIC BODY COLOR FOR IDENTIFICATION PURPOSES. 2D MODE REPLY 26AD063AJ91 AXGNJ /D/ 10CROSS SECTION,LARGEST LARGEST CROSS SECTION NONE. 1D AND 1B MODE REPLY11AA05 AXGPJ /D/ 10CROSS SECTION,SMALLER SMALLER CROSS SECTION NONE. 1D AND 1B MODE REPLY11AA05 AXGRJ 10TORQUE,DEVICE,ADJUSTMENT ADJUSTMENT DEVICE TORQUE THE TORQUE REQUIRED FOR THE ADJUSTMENT DEVICE. 2D AND 1B MODE REPLY21AA561AC20 AXGSD 14SHAPE,BUSHING BUSHING SHAPE THE PHYSICAL CONFIGURATION OF THE BUSHING. SELECT REPLY CODE 10AD07 AXGTJ 10RESISTANCE AT 25 DEG CELSIUS,DC,INSULATION INSULATION DC RESISTANCE AT 25 DEG CELSIUS DIRECT CURRENT RESISTANCE BETWEEN TWO CONDUCTORS THAT ARE SEPARATED BY AN INSULATING MATERIAL,MEASURED AT 25 DEGREES CELSIUS. 1D AND 1B MODE REPLY11AA57 AXGWD /D/ 08LOCATION,HOLE,END END HOLE LOCATION INDICATES THE LOCATION OF THE HOLES IN RESPECT TO THE ENDS OF THE ITEM. SELECT REPLY CODE 10AJ91 AXGXJ 10RESISTANCE AT MAX OPERATING TEMP,DC,INSULATION INSULATION DC RESISTANCE AT MAX OPERATING TEMP DIRECT CURRENT RESISTANCE BETWEEN TWO CONDUCTORS THAT ARE SEPARATED BY AN INSULATING MATERIAL,MEASURED AT THE MAXIMUM OPERATING TEMPERATURE OF THE ITEM. 1D AND 1B MODE REPLY11AA57 AXGYD 11METHOD,MOUNTING MOUNTING METHOD THE MEANS OF ATTACHING THE ITEM. SELECT REPLY CODE 10AM39 AXGZD /D/ 09MATERIAL,SUPPORTING,INSULATION INSULATION SUPPORTING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INSULATION SUPPORTING MATERIAL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AXHAJ 10GAP,AIR,PLATE PLATE AIR GAP THE AMOUNT OF AIR SPACE BETWEEN THE PLATES. 1D AND 1B MODE REPLY11AA05 AXHBA /D/ 12QUANTITY,TRANSFORMER TRANSFORMER QUANTITY THE NUMBER OF TRANSFORMERS INCLUDED. 1A MODE REPLY 0 AXHCG /D/ 19NAME,TRANSFORMER TRANSFORMER NAME THE NOMENCLATURE BY WHICH THE TRANSFORMER IS IDENTIFIED. FULL TEXT WRITE-IN 0 AXHDJ /D/ 04DISTANCE BETWEEN STAND-OFF PARALLEL TO HEIGHT,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN STAND-OFF PARALLEL TO HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AXHEJ /D/ 04DISTANCE BETWEEN STAND-OFF PARALLEL TO WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN STAND-OFF PARALLEL TO WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXHFJ /D/ 04LENGTH,STAND-OFF STAND-OFF LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXHGJ 04WIDTH,BUSHING BUSHING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXHHD /D/ 18TYPE,DEVICE,COIL TUNING COIL TUNING DEVICE TYPE INDICATES THE TYPE OF TUNING DEVICE INCLUDED WITH THE COIL/S/. SELECT REPLY CODE 10AB87 AXHJA 12QUANTITY,TERMINAL,MAIN MAIN TERMINAL QUANTITY THE NUMBER OF MAIN TERMINALS PROVIDED. 1A MODE REPLY 0 AXHKD 18TYPE,TERMINAL,MAIN MAIN TERMINAL TYPE INDICATES THE TYPE OF MAIN TERMINAL/S/ PROVIDED. SELECT REPLY CODE 10AA58 AXHLG 10PERMEABILITY RATING PERMEABILITY RATING AN INDICATION OF THE PERMEABILITY RATING OF THE ITEM. FULL TEXT WRITE-IN 0 AXHMA 12QUANTITY INTERNALLY CONNECTED TO MAIN TERMINAL,TERMINAL,CONTROL CONTROL TERMINAL QUANTITY INTERNALLY CONNECTED TO MAIN TERMINAL THE NUMBER OF CONTROL TERMINALS THAT ARE INTERNALLY CONNECTED TO THE MAIN TERMINALS. 1A MODE REPLY 0 AXHNJ 04DIAMETER FOR WHICH RIGID MOUNT IS DESIGNED,MOTOR MOTOR DIAMETER FOR WHICH RIGID MOUNT IS DESIGNED THE DIAMETER OF THE MOTOR FOR WHICH THE RIGID MOUNT IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 AXHPJ 04DIAMETER,HOLE,FIRST MOUNTING FIRST MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXHQA 12QUANTITY,GROOVE GROOVE QUANTITY THE NUMBER OF GROOVES PROVIDED. 1A MODE REPLY 0 AXHRJ A18TYPE AND QUANTITY,FACILITY,MOUNTING MOUNTING FACILITY TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF FACILITIES BY WHICH THE ITEM IS MOUNTED. 1D AND 1A MODE REPLY13AM39 AXHSJ 10SPACING,GROOVE GROOVE SPACING THE SPACING BETWEEN THE GROOVES. 2D AND 1B MODE REPLY21AA051AC20 AXHTJ /D/ 10SYSTEM FOR WHICH DESIGNED,VOLTAGE VOLTAGE SYSTEM FOR WHICH DESIGNED THE ELECTRICAL VOLTAGE OF THE SYSTEM FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AB631AC20 AXHWD /D/ 14SHAPE,CROSS-SECTIONAL,WINDING AREA WINDING AREA CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE WINDING AREA WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 AXHXD 18TYPE,POLARITY,GROUND GROUND POLARITY TYPE INDICATES THE TYPE OF GROUND POLARITY UTILIZED. SELECT REPLY CODE 10AG39 AXHYA 13THREAD SIZE,BODY BODY THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE BODY. 1A MODE REPLY 0 AXHZJ 10VOLTAGE RATING,CUT-IN CUT-IN VOLTAGE RATING THE CUT-IN VOLTAGE/S/ REQUIRED TO CLOSE THE CIRCUIT. 2D AND 1B MODE REPLY21AB631AC20 AXJAD /D/ 07COUPLING,FLUID FLUID COUPLING AN INDICATION OF WHETHER OR NOT A FLUID COUPLING IS INCLUDED. SELECT REPLY CODE 10AA49 AXJBD /D/ 07TRANSMISSION TRANSMISSION AN INDICATION OF WHETHER OR NOT A TRANSMISSION IS INCLUDED. SELECT REPLY CODE 10AA49 AXJCD /D/ 07FEATURE,USAGE,TRAINING TRAINING USAGE FEATURE AN INDICATION OF WHETHER OR NOT A TRAINING USAGE FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AXJDD 18TYPE,TRANSMISSION TRANSMISSION TYPE INDICATES THE TYPE OF TRANSMISSION USED TO TRANSFER DEVELOPED MECHANICAL ENERGY TO THE DRIVE UNIT. SELECT REPLY CODE 10AM54 AXJEA 12QUANTITY,RANGE,SPEED SPEED RANGE QUANTITY THE NUMBER OF SPEED RANGES PROVIDED. 1A MODE REPLY 0 AXJFA 12QUANTITY PER RANGE,SPEED,FORWARD FORWARD SPEED QUANTITY PER RANGE THE NUMBER OF FORWARD SPEEDS IN EACH RANGE. 1A MODE REPLY 0 AXJGJ /D/ 10TENSION RATING,INITIAL INITIAL TENSION RATING THE INITIAL LOAD FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY22AB161AC20 AXJHA 12QUANTITY,SPEED,FORWARD FORWARD SPEED QUANTITY THE NUMBER OF FORWARD SPEEDS PROVIDED. 1A MODE REPLY 0 AXJJD /D/ 07OVERDRIVE OVERDRIVE AN INDICATION OF WHETHER OR NOT AN OVERDRIVE IS INCLUDED. SELECT REPLY CODE 10AA49 AXJKD /D/ 07DRIVE,CROSS CROSS DRIVE AN INDICATION OF WHETHER OR NOT A CROSS DRIVE IS INCLUDED. SELECT REPLY CODE 10AA49 AXJLD /D/ 07CLUTCH CLUTCH AN INDICATION OF WHETHER OR NOT A CLUTCH IS INCLUDED. SELECT REPLY CODE 10AA49 AXJMD 05DIRECTION,ROTATION,MAIN POWER TAKEOFF MAIN POWER TAKEOFF ROTATION DIRECTION THE DIRECTION OF THE MAIN POWER TAKEOFF ROTATION,WHEN VIEWED FROM AND FACING THE MAIN DRIVE END. SELECT REPLY CODE 10AB50 AXJND 18TYPE,DRIVE,MAIN POWER TAKEOFF MAIN POWER TAKEOFF DRIVE TYPE INDICATES THE TYPE OF DRIVE PROVIDED ON THE MAIN POWER TAKEOFF. SELECT REPLY CODE 10AJ80 AXJPJ 04SIZE,MATERIAL MATERIAL SIZE NONE. 2D AND 1B MODE REPLY21AA051AC20 AXJQJ 04LENGTH,SOLID,SPRING SPRING SOLID LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXJRJ 04DIAMETER,OUTSIDE,SPRING SOLID SPRING SOLID OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXJSJ 04DIAMETER,OUTSIDE,PULLEY PULLEY OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PULLEY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AXJTJ 04LENGTH,CONTACT CONTACT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXJWA 12QUANTITY,UNIT,POWER TAKEOFF,AUXILIARY AUXILIARY POWER TAKEOFF UNIT QUANTITY THE NUMBER OF AUXILIARY POWER TAKEOFF UNITS INCLUDED WITH THE ITEM. 1A MODE REPLY 0 AXJXJ 04LENGTH,OVERALL,COIL FREE COIL FREE OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXJYD /D/ 08LOCATION,UNIT,AUXILIARY POWER TAKEOFF AUXILIARY POWER TAKEOFF UNIT LOCATION INDICATES THE LOCATION OF THE AUXILIARY POWER TAKEOFF UNIT,WHEN VIEWED FROM AND FACING THE MAIN DRIVING END. SELECT REPLY CODE 10AJ91 AXJZJ 04LENGTH,INSIDE,FREE,HOOK TO HOOK HOOK TO HOOK FREE INSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXKAD /D/ 07FEATURE,CONTROLLED,GOVERNOR GOVERNOR CONTROLLED FEATURE AN INDICATION OF WHETHER OR NOT A GOVERNOR CONTROLLED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AXKBJ /D/ 04RADIUS,CONNECTOR CONNECTOR RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AXKCA /D/ 16STYLE DESIGNATOR,END END STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END. 1A MODE REPLY 0 AXKDD 19OUTPUT FOR WHICH DESIGNED,POWER POWER OUTPUT FOR WHICH DESIGNED THE POWER OUTPUT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL40 AXKEB 10HORSEPOWER RATING,SHAFT SHAFT HORSEPOWER RATING THE POWER DELIVERED BY THE SHAFT AT A SPECIFIC SPEED. 1B MODE REPLY 0 AXKFG /D/ 19POSITION,RELATIVE,HOOK/LOOP HOOK/LOOP RELATIVE POSITION AN INDICATION OF THE RELATIVE POSITION OF THE HOOK/S/ AND/OR LOOP/S/. FULL TEXT WRITE-IN 0 AXKGB 10SPEED IN RPM,HORSEPOWER RATING,SHAFT SHAFT HORSEPOWER RATING SPEED IN RPM THE ROTARY SPEED OF THE SHAFT AT WHICH THE HORSEPOWER RATING IS DETERMINED,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 AXKHB 10HORSEPOWER RATING,AIR AIR HORSEPOWER RATING THE RATED AIR HORSEPOWER PRODUCED BY THE ITEM. 1B MODE REPLY 0 AXKJJ /D/ 04LENGTH AND LOCATION,INSIDE,COIL TO HOOK COIL TO HOOK INSIDE LENGTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 AXKKJ 10FLOW RATE,AIR AIR FLOW RATE THE RATED CAPACITY OF AIR FLOW DISCHARGED BY THE ITEM. 1D AND 1B MODE REPLY12AL69 AXKLJ /D/ 04WIDTH AND LOCATION,OPENING,HOOK HOOK OPENING WIDTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 AXKMJ /D/ 04RADIUS AND LOCATION,HOOK HOOK RADIUS AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 AXKNJ 10PRESSURE RATING,DISCHARGE DISCHARGE PRESSURE RATING THE RATED DISCHARGE PRESSURE OF THE ITEM. 1D AND 1B MODE REPLY12AB16 AXKPJ /D/ 04DIAMETER AND LOCATION,BOLT BOLT DIAMETER AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 AXKQJ /D/ 04LENGTH AND LOCATION,BOLT BOLT LENGTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 AXKRJ /D/ 04LENGTH AND LOCATION,HOOK END HOOK END LENGTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 AXKSJ /D/ 04WIDTH AND LOCATION,HOOK HOOK WIDTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 AXKTJ 10ALTITUDE AT WHICH HORSEPOWER IS RATED ALTITUDE AT WHICH HORSEPOWER IS RATED THE ALTITUDE AT WHICH THE HORSEPOWER IS RATED. 1D AND 1B MODE REPLY11AA05 AXKWJ /D/ 04LENGTH AND LOCATION,END END LENGTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 AXKXJ /D/ 04SIZE AND LOCATION,END,HUB HUB END SIZE AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 AXKYJ 10TEMP AT WHICH HORSEPOWER IS RATED,AIR,INLET INLET AIR TEMP AT WHICH HORSEPOWER IS RATED THE TEMPERATURE OF THE INLET AIR AT WHICH THE HORSEPOWER IS RATED. 1D AND 1B MODE REPLY11AB36 AXKZJ /D/ 04DIAMETER AND LOCATION,HOLE HOLE DIAMETER AND LOCATION THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE,AND TERMINATES AT THE INNER CIRCUMFERENCE,AND ITS LOCATION ON THE ITEM. 3D AND 1B MODE REPLY31AA051AC203AJ91 AXLAG /D/ 10LIFE AT RATED HORSEPOWER,DESIGN DESIGN LIFE AT RATED HORSEPOWER THE DESIGN LIFE EXPECTANCY OF THE ITEM AT SPECIFIED HORSEPOWER RATING. FULL TEXT WRITE-IN 0 AXLBJ /D/ 04LENGTH AND LOCATION,HUB END SPUR HUB END SPUR LENGTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 AXLCJ /D/ 04LENGTH AND LOCATION,HOOK OPENING HOOK OPENING LENGTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 AXLDJ /D/ 04SIZE AND LOCATION,HUB HUB SIZE AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 AXLEJ /D/ 04RADIUS AND LOCATION,END END RADIUS AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 AXLFG 10HORSEPOWER AT SPECIFIED PRM,RATED,AHEAD AHEAD RATED HORSEPOWER AT SPECIFIED RPM THE RATED HORSEPOWER OF THE ITEM IN AHEAD /FORWARD/ MOTION,AT SPECIFIED REVOLUTIONS PER MINUTE. FULL TEXT WRITE-IN 0 AXLGG 10HORSEPOWER AT SPECIFIED RPM,RATED,ASTERN ASTERN RATED HORSEPOWER AT SPECIFIED RPM THE RATED HORSEPOWER OF THE ITEM IN ASTERN /REVERSE/ MOTION,AT SPECIFIED REVOLUTIONS PER MINUTE. FULL TEXT WRITE-IN 0 AXLHD 05DIRECTION,HELIX,COIL COIL HELIX DIRECTION AN INDICATION OF THE COIL HELIX DIRECTION. SELECT REPLY CODE 10AA38 AXLJD 08LOCATION,TURBINE,ASTERN ASTERN TURBINE LOCATION INDICATES THE LOCATION OF THE ASTERN (REVERSE) TURBINE. SELECT REPLY CODE 10AM55 AXLKA 12QUANTITY,COIL,ACTIVE ACTIVE COIL QUANTITY THE NUMBER OF ACTIVE COILS PROVIDED. 1A MODE REPLY 0 AXLLJ /D/ 10TENSION RATING,INITIAL,CLOSED COIL CLOSED COIL INITIAL TENSION RATING THE INITIAL LOAD FOR WHICH THE CLOSED COIL IS RATED. 2D AND 1B MODE REPLY22AB161AC20 AXLMG /D/ 10HARDNESS RATING,MATERIAL MATERIAL HARDNESS RATING A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF THE MATERIAL WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE. FULL TEXT WRITE-IN 0 AXLNG 10LOAD RATING,SUPPORT SUPPORT LOAD RATING THE AMOUNT OF LOAD THE ITEM IS RATED TO SUPPORT. FULL TEXT WRITE-IN 0 AXLPJ 10DEFLECTION RATE,SPRING SPRING DEFLECTION RATE THE WEIGHT,PER SPECIFIC MEASUREMENT SCALE,REQUIRED TO DEFLECT THE SPRING. 2D AND 1B MODE REPLY22AG671AC20 AXLQJ 04DIAMETER,OUTSIDE,SPRING FREE SPRING FREE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXLRD /D/ 07FEATURE,BLASTED,SHOT SHOT BLASTED FEATURE AN INDICATION OF WHETHER OR NOT A SHOT BLASTED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AXLSG /D/ 10TORQUE AT SPECIFIED ROTATION DEG,RATED RATED TORQUE AT SPECIFIED ROTATION DEG THE ABILITY OF AN ITEM TO WITHSTAND A LOAD WITHOUT A FRACTURE,AT A SPECIFIED DEGREE OF ROTATION. FULL TEXT WRITE-IN 0 AXLTJ 04DIAMETER,OUTSIDE,COIL COIL OUTSIDE DIAMETER NONE. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 2D AND 1B MODE REPLY21AA051AC20 AXLWJ 04DIAMETER,INSIDE,COIL COIL INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COIL,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AXLXJ 04DISTANCE,COIL AXIS TO CENTER SECTION COIL AXIS TO CENTER SECTION DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AXLYJ 04RADIUS,LOOP,CENTER CENTER LOOP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AXLZB /D/ 04ANGLE IN DEG,TANGENT,END END TANGENT ANGLE IN DEG NONE. 1B MODE REPLY 0 AXMAG /D/ 11METHOD,ATTACHMENT TO ITEM SUPPORTED ATTACHMENT TO ITEM SUPPORTED METHOD THE MEANS USED IN ATTACHING THE ITEM TO THE ITEM SUPPORTED. FULL TEXT WRITE-IN 0 AXMBJ 04LENGTH,END END LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AXMCJ 04RADIUS,HOOK HOOK RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AXMDJ 04RADIUS,BEND,FIRST FIRST BEND RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AXMEJ 04RADIUS,BEND,SECOND SECOND BEND RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AXMFJ 04RADIUS,BEND,THIRD THIRD BEND RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AXMGJ /D/ 04RADIUS,BEND,FOURTH FOURTH BEND RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AXMHD 19RELATIONSHIP,ANGULAR,END END ANGULAR RELATIONSHIP AN INDICATION OF THE ANGULAR RELATIONSHIP OF THE ENDS OF THE ITEM. SELECT REPLY CODE 10AF63 AXMJJ /D/ 04ANGLE IN DEG,END END ANGLE IN DEG THE ANGLE FORMED IN THE END/S/ OF THE ITEM,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 AXMKA /D/ 16STYLE,CENTER CENTER STYLE THE PREFORMED SHAPE OF THE MIDDLE SECTION OF THE ITEM. 1A MODE REPLY 0 AXMLJ /D/ 10LOAD RATING,TORQUE TORQUE LOAD RATING AN INDICATION OF THE TORQUE LOAD FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY21AA561AC20 AXMMB /D/ 10DEG,ROTATION,TORQUE LOAD RATING TORQUE LOAD RATING ROTATION DEG THE DEGREE OF ROTATION AT WHICH THE TORQUE LOAD IS RATED. 1B MODE REPLY 0 AXMNJ 10VOLTAGE RATING,CUTOUT CUTOUT VOLTAGE RATING THE CUTOUT VOLTAGE/S/ REQUIRED TO OPEN /BREAK/ THE CIRCUIT. 2D AND 1B MODE REPLY21AB631AC20 AXMPD 18TYPE,INSERT INSERT TYPE INDICATES THE TYPE OF INSERT PROVIDED. SELECT REPLY CODE 10AB47 AXMQA 13THREADED STUD SIZE THREADED STUD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED STUD. 1A MODE REPLY 0 AXMRJ 10CURRENT RATING,CUTOUT CUTOUT CURRENT RATING THE DISCHARGE CURRENT(S) REQUIRED TO OPEN (BREAK) THE CURRENT. 2D AND 1B MODE REPLY21AC301AC20 AXMSJ 04LENGTH,EXPOSED,INSERT INSERT EXPOSED LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE EXPOSED PORTION OF THE INSERT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AXMTA /D/ 12QUANTITY,REACTOR REACTOR QUANTITY THE NUMBER OF REACTORS PROVIDED. 1A MODE REPLY 0 AXMWG 11METHOD,SUPPORTED,ATTACHMENT TO ITEM ATTACHMENT TO ITEM SUPPORTED METHOD THE MEANS USED IN ATTACHING THE ITEM TO THE ITEM SUPPORTED. FULL TEXT WRITE-IN 0 AXMXG 11METHOD,ATTACHMENT,SUPPORTING OBJECT/SURFACE SUPPORTING OBJECT/SURFACE ATTACHMENT METHOD THE MEANS USED IN ATTACHING THE ITEM TO A SUPPORTING OBJECT OR SURFACE. FULL TEXT WRITE-IN 0 AXMYG /D/ 11METHOD,MOUNTING,SHOCK/SPRING SHOCK/SPRING MOUNTING METHOD THE MEANS USED IN MOUNTING THE ITEM WITH SPRINGS OR SHOCKS. FULL TEXT WRITE-IN 0 AXMZJ /D/ 10DC RATING DC RATING THE AMOUNT OF DIRECT CURRENT FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AC301AC20 AXNAJ 04THREAD DIAMETER,PLUG,SPARK,ACCOMMODATED ACCOMMODATED SPARK PLUG THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE ACCOMMODATED SPARK PLUG,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AXNBJ 04THREAD DIAMETER,OUTSIDE OUTSIDE THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE OUTSIDE OF THE ITEM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AXNCD /D/ 07HEAD HEAD AN INDICATION OF WHETHER OR NOT A HEAD IS INCLUDED. SELECT REPLY CODE 10AA49 AXNDD /D/ 07FEATURE,COUNTERBORE COUNTERBORE FEATURE AN INDICATION OF WHETHER OR NOT A COUNTERBORE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AXNEJ 04DIAMETER,COUNTERBORE,HEAD END HEAD END COUNTERBORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COUNTERBORED PORTION OF THE HEAD END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AXNFJ 04DEPTH,COUNTERBORE,HEAD END HEAD END COUNTERBORE DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE COUNTERBORED PORTION OF THE HEAD END,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AXNGJ /D/ 10RESISTANCE,DC DC RESISTANCE THE OPPOSITION TO THE FLOW OF DIRECT CURRENT OFFERED BY AN ITEM. 2D AND 1B MODE REPLY22AE751AC20 AXNHJ 04DIAMETER,COUNTERBORE,BOTTOM END BOTTOM END COUNTERBORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COUNTERBORED PORTION OF THE BOTTOM END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AXNJJ 04DEPTH,COUNTERBORE,BOTTOM END BOTTOM END COUNTERBORE DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE COUNTERBORED PORTION OF THE BOTTOM END,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AXNKJ 10VOLTAGE RATING,INPUT INPUT VOLTAGE RATING THE INPUT VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE. 2D AND 1B MODE REPLY21AB631AC20 AXNLJ /D/ 10VOLTAGE RATING,OUTPUT OUTPUT VOLTAGE RATING THE OUTPUT VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE. 2D AND 1B MODE REPLY21AB631AC20 AXNMD /D/ 02DESIGN,PLUG PLUG DESIGN THE DESIGN OF THE PLUG. SELECT REPLY CODE 10AD07 AXNND /D/ 07FEATURE,SEALED,HERMETICALLY HERMETICALLY SEALED FEATURE AN INDICATION OF WHETHER OR NOT A HERMETICALLY SEALED FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 AXNPJ 10CURRENT RATING CURRENT RATING THE AMOUNT OF CURRENT FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AC301AC20 AXNQJ /D/ 10FREQUENCY FOR WHICH DESIGNED FREQUENCY FOR WHICH DESIGNED THE APPROXIMATE FREQUENCY,EITHER ABOVE OR BELOW A SPECIFIED VALUE,AT WHICH THE ITEM IS DESIGNED TO OPERATE. 2D AND 1B MODE REPLY22AB492AM56 AXNRD 19CHARACTERISTIC,TERMINAL TERMINAL CHARACTERISTIC THE CHARACTERISTIC OF THE TERMINAL FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. SELECT REPLY CODE 10AH46 AXNSG 04SIZE,TERMINAL TERMINAL SIZE DESIGNATES THE SIZE OF THE TERMINAL. FULL TEXT WRITE-IN 0 AXNTJ 04LENGTH,PROTRUSION,CONTACT CONTACT PROTRUSION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CONTACT PROTRUSION WHICH EXTENDS FROM THE ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AXNWJ 10SIZE,WIRE,ACCOMMODATED ACCOMMODATED WIRE SIZE DESIGNATES THE SIZE OF THE WIRE ACCOMMODATED BY THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 AXNXA 04SIZE,AWG,ACCOMMODATED WIRE ACCOMMODATED WIRE AWG SIZE THE AMERICAN WIRE GAGE SIZE OF THE ACCOMMODATED WIRE. 1A MODE REPLY 0 AXNYA 12QUANTITY,STAGE,AHEAD IMPULSE AHEAD IMPULSE STAGE QUANTITY THE NUMBER OF AHEAD /FORWARD/ IMPULSE STAGES EMPLOYED BY THE ITEM. 1A MODE REPLY 0 AXNZJ 04DIAMETER,HOLE,SECOND MOUNTING SECOND MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXPAJ 04DIAMETER,HOLE,THIRD MOUNTING THIRD MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXPBJ 04DIAMETER,HOLE,FOURTH MOUNTING FOURTH MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXPCJ 04DISTANCE BETWEEN FIRST AND SECOND MOUNTING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FIRST AND SECOND MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AXPDJ 04DISTANCE BETWEEN SECOND AND THIRD MOUNTING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SECOND AND THIRD MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AXPEJ 04DISTANCE BETWEEN FIRST AND THIRD MOUNTING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FIRST AND THIRD MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 AXPFJ 04DISTANCE FROM BASE OF COIL TO MOUNTING DISTANCE FROM BASE OF COIL TO MOUNTING NONE. 2D AND 1B MODE REPLY21AA051AC20 AXPGA 12QUANTITY,ROW,ROTATION BLADE,AHEAD IMPULSE STAGE AHEAD IMPULSE STAGE ROTATION BLADE ROW QUANTITY THE NUMBER OF ROWS OF ROTATING BLADES ON THE AHEAD /FORWARD/ IMPULSE STAGE. 1A MODE REPLY 0 AXPHD /D/ 07GROOVE,OIL OIL GROOVE AN INDICATION OF WHETHER OR NOT AN OIL GROOVE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 AXPJJ /D/T10RANGE,SCALE SCALE RANGE AN INDICATION OF THE SCALE RANGE. 1D AND 1F MODE REPLY12AB49 AXPKJ 04DISTANCE FROM PIN HOLE CENTER TO EXTREME TOP DISTANCE FROM PIN HOLE CENTER TO EXTREME TOP THE DISTANCE FROM THE CENTER OF THE PIN HOLE TO THE EXTREME TOP OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 AXPLD /D/ 07BUSHING,HOLE,PIN PIN HOLE BUSHING AN INDICATION OF WHETHER OR NOT A PIN HOLE BUSHING/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 AXPMJ 04DISTANCE BETWEEN PIN BOSSES DISTANCE BETWEEN PIN BOSSES THE DISTANCE BETWEEN PIN BOSSES ON AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 AXPND /D/ 07GROOVE,RING,RETAINING RETAINING RING GROOVE AN INDICATION OF WHETHER OR NOT A RETAINING RING GROOVE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 AXPPD /D/ 07PIN PIN AN INDICATION OF WHETHER OR NOT A PIN IS INCLUDED. SELECT REPLY CODE 10AA49 AXPQD /D/ 18TYPE FOR WHICH DESIGNED,PIN PIN TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF PIN FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 AXPRD /D/ 07RING RING AN INDICATION OF WHETHER OR NOT A RING(S) IS INCLUDED. PLEASE USE MRC ABFF FOR NIINS WERE ANSWERED WITH "INCLUDED" IN PLACE OF THIS CANCELLED MRC. SELECT REPLY CODE 10AA49 AXPSD /D/ 07ROD,CONNECTING,INTEGRAL INTEGRAL CONNECTING ROD AN INDICATION OF WHETHER OR NOT AN INTEGRAL CONNECTING ROD IS INCLUDED. SELECT REPLY CODE 10AA49 AXPTH /D/ 14SHAPE AND LOCATION,END END SHAPE AND LOCATION THE PHYSICAL CONFIGURATION OF THE END/S/ AND ITS LOCATION ON THE ITEM. 2D MODE REPLY 22AD073AJ91 AXPWJ 04THICKNESS,END END THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE END,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AXPXJ 04DIAMETER,INSIDE,TERMINAL TERMINAL INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TERMINAL,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AXPYA 12QUANTITY,OPENING OPENING QUANTITY THE NUMBER OF OPENINGS IN THE ITEM. 1A MODE REPLY 0 AXPZJ 04SIZE,OPENING OPENING SIZE DESIGNATES THE SIZE OF THE TOTAL SURFACE OF AN OPENING. 1D AND 1B MODE REPLY11AA05 AXQAG 08LOCATION,OPENING OPENING LOCATION INDICATES THE LOCATION OF THE OPENING/S/ IN THE ITEM. FULL TEXT WRITE-IN 0 AXQBD 19CHARACTERISTIC,OPENING OPENING CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC OF THE OPENING(S). SELECT REPLY CODE 10AL72 AXQCJ 04THICKNESS,MATERIAL,OUTER SHELL OUTER SHELL MATERIAL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE OUTER SHELL MATERIAL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AXQDJ 10CAPACITY CAPACITY A MEASUREMENT OF THE CAPACITY OF AN ITEM. 1D AND 1B MODE REPLY12AG67 AXQED /D/ 07BASE,MOUNTING MOUNTING BASE AN INDICATION OF WHETHER OR NOT A MOUNTING BASE IS INCLUDED. SELECT REPLY CODE 10AA49 AXQFJ 04DIAMETER,PLUNGER PLUNGER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PLUNGER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AXQGD /D/ 07HANDLE,CARRYING CARRYING HANDLE AN INDICATION OF WHETHER OR NOT A CARRYING HANDLE IS INCLUDED. SELECT REPLY CODE 10AA49 AXQHD 18TYPE,INTELLIGENCE,INPUT INPUT INTELLIGENCE TYPE INDICATES THE TYPE OF INTELLIGENCE THE ITEM IS CAPABLE OF RECEIVING. SELECT REPLY CODE 10AJ41 AXQJD 11METHOD,INPUT,INTELLIGENCE INTELLIGENCE INPUT METHOD THE MEANS USED TO INPUT THE INTELLIGENCE. SELECT REPLY CODE 10AC58 AXQKD 18TYPE,INTELLIGENCE,OUTPUT OUTPUT INTELLIGENCE TYPE INDICATES THE TYPE OF INTELLIGENCE THE ITEM IS CAPABLE OF TRANSMITTING. SELECT REPLY CODE 10AJ41 AXQLD 18TYPE,INLET,PRESSURE PRESSURE INLET TYPE INDICATES THE TYPE OF PRESSURE INLET PROVIDED. SELECT REPLY CODE 10AA84 AXQMD 18TYPE,COMPUTATION COMPUTATION TYPE INDICATES THE TYPE OF COMPUTATION PROVIDED. SELECT REPLY CODE 10AJ48 AXQNJ 10CAPACITY RATING,MAXIMUM MAXIMUM CAPACITY RATING A MEASUREMENT OF THE CAPACITY FOR WHICH AN ITEM IS RATED. 1D AND 1B MODE REPLY12AB49 AXQPJ /D/ 10CAPACITY RATING,PRESSURE,MAXIMUM DRIVING MAXIMUM DRIVING PRESSURE CAPACITY RATING THE MAXIMUM DRIVING PRESSURE CAPACITY FOR WHICH AN ITEM IS RATED. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1D AND 1B MODE REPLY12AB16 AXQQA 12QUANTITY,INLET,PRESSURE PRESSURE INLET QUANTITY THE NUMBER OF PRESSURE INLETS PROVIDED. 1A MODE REPLY 0 AXQRG 04SIZE,OPENING,PRESSURE INLET PRESSURE INLET OPENING SIZE DESIGNATES THE SIZE OF THE TOTAL SURFACE OF A PRESSURE INLET OPENING. FULL TEXT WRITE-IN 0 AXQSG /D/ 04SIZE,CONNECTION,PRESSURE INLET PIPE/HOSE PRESSURE INLET PIPE/HOSE CONNECTION SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSION(S) OF THE PRESSURE INLET PIPE AND/OR HOSE CONNECTION. FULL TEXT WRITE-IN 0 AXQTA 12QUANTITY,INLET,SUCTION SUCTION INLET QUANTITY THE NUMBER OF SUCTION INLETS PROVIDED. 1A MODE REPLY 0 AXQWD 18TYPE,INLET,SUCTION SUCTION INLET TYPE INDICATES THE TYPE OF SUCTION INLET PROVIDED. SELECT REPLY CODE 10AA84 AXQXA 12QUANTITY,OUTLET,DISCHARGE DISCHARGE OUTLET QUANTITY THE NUMBER OF DISCHARGE OUTLETS PROVIDED. 1A MODE REPLY 0 AXQYD 18TYPE,OUTLET,DISCHARGE DISCHARGE OUTLET TYPE INDICATES THE TYPE OF DISCHARGE OUTLET PROVIDED. SELECT REPLY CODE 10AA84 AXQZG /D/ 04SIZE,CONNECTION,DISCHARGE OUTLET PIPE/HOSE DISCHARGE OUTLET PIPE/HOSE CONNECTION SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSION/S/ OF THE DISCHARGE OUTLET PIPE AND/OR HOSE CONNECTION. FULL TEXT WRITE-IN 0 AXRAG /D/ 04SIZE,OPENING,SUCTION INLET SUCTION INLET OPENING SIZE DESIGNATES THE SIZE OF THE TOTAL SURFACE OF A SUCTION INLET OPENING. FULL TEXT WRITE-IN 0 AXRBG /D/ 04SIZE,CONNECTION,SUCTION INLET PIPE/HOSE SUCTION INLET PIPE/HOSE CONNECTION SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSION(S) OF THE SUCTION INLET PIPE AND/OR HOSE CONNECTION. FULL TEXT WRITE-IN 0 AXRCA 12QUANTITY,ROW,STATIONARY BLADE,AHEAD IMPULSE STAGE AHEAD IMPULSE STAGE STATIONARY BLADE ROW QUANTITY THE NUMBER OF ROWS OF STATIONARY BLADES ON THE AHEAD /FORWARD/ IMPULSE STAGE. 1A MODE REPLY 0 AXRDA 12QUANTITY,STAGE,AHEAD REACTION AHEAD REACTION STAGE QUANTITY THE NUMBER OF AHEAD /FORWARD/ REACTION STAGES EMPLOYED BY THE ITEM. 1A MODE REPLY 0 AXREA 12QUANTITY,ROW,ROTATION BLADE,AHEAD REACTION STAGE AHEAD REACTION STAGE ROTATION BLADE ROW QUANTITY THE NUMBER OF ROWS OF ROTATING BLADES ON THE AHEAD /FORWARD/ REACTION STAGE. 1A MODE REPLY 0 AXRFD 18TYPE,FLOW,AHEAD AHEAD FLOW TYPE INDICATES THE AHEAD FLOW TYPE OF THE ITEM. SELECT REPLY CODE 10AK04 AXRGD 02DESIGN,STAGE,ASTERN ASTERN STAGE DESIGN THE TERM USED TO DESCRIBE THE ASTERN (REVERSE) STAGE DESIGN OF THE ITEM. SELECT REPLY CODE 10AM57 AXRHA 12QUANTITY,ROW,ASTERN ROTATION BLADE ASTERN ROTATION BLADE ROW QUANTITY THE NUMBER OF ROWS OF ASTERN /REVERSE/ ROTATING BLADES ON THE ITEM. 1A MODE REPLY 0 AXRJA 12QUANTITY,ROW,ASTERN STATIONARY BLADE ASTERN STATIONARY BLADE ROW QUANTITY THE NUMBER OF ROWS OF THE ASTERN /REVERSE/ STATIONARY BLADES ON THE ITEM. 1A MODE REPLY 0 AXRKD 18TYPE,FLOW,ASTERN ASTERN FLOW TYPE INDICATES THE ASTERN FLOW TYPE OF THE ITEM. SELECT REPLY CODE 10AK04 AXRLJ 10PRESSURE,GAGE,AHEAD INITIAL STEAM AHEAD INITIAL STEAM GAGE PRESSURE THE INITIAL AHEAD /FORWARD/ STEAM GAGE PRESSURE REQUIRED TO OPERATE THE ITEM. 1D AND 1B MODE REPLY12AG20 AXRMJ 10PRESSURE,GAGE,ASTERN INITIAL STEAM ASTERN INITIAL STEAM GAGE PRESSURE THE INITIAL ASTERN /REVERSE/ STEAM GAGE PRESSURE REQUIRED TO OPERATE THE ITEM. 1D AND 1B MODE REPLY12AG20 AXRNJ 10TEMP,STEAM,INITIAL,AHEAD AHEAD INITIAL STEAM TEMP THE INITIAL AHEAD (FORWARD) STEAM TEMPERATURE REQUIRED TO OPERATE THE ITEM. 1D AND 1B MODE REPLY12AG20 AXRPJ 10TEMP,STEAM,INITIAL,ASTERN ASTERN INITIAL STEAM TEMP THE INITIAL ASTERN (REVERSE) STEAM TEMPERATURE REQUIRED TO OPERATE THE ITEM. 1D AND 1B MODE REPLY12AG20 AXRQD 19FORM,ASSEMBLED,REDUCTION GEAR REDUCTION GEAR ASSEMBLED FORM AN INDICATION OF THE ASSEMBLED FORM IN WHICH THE REDUCTION GEAR IS SUPPLIED. SELECT REPLY CODE 10AB28 AXRRG /D/ 19ADDRESS,MANUFACTURER,REDUCTION GEAR REDUCTION GEAR MANUFACTURER ADDRESS THE ADDRESS OF THE COMPANY MANUFACTURING THE REDUCTION GEAR. FULL TEXT WRITE-IN 0 AXRSA 19CODE,MANUFACTURER,REDUCTION GEAR REDUCTION GEAR MANUFACTURER CODE THE IDENTIFYING CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURERS THE REDUCTION GEAR. 1A MODE REPLY 0 AXRTA 12QUANTITY PER REVOLUTION,IMPULSE IMPULSE QUANTITY PER REVOLUTION THE NUMBER OF IMPULSES PRODUCED BY ONE COMPLETE REVOLUTION. 1A MODE REPLY 0 AXRWD 18TYPE FOR WHICH DESIGNED,IGNITION IGNITION TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF IGNITION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AB03 AXRXD 18TYPE,GEAR,REDUCTION REDUCTION GEAR TYPE INDICATES THE TYPE OF REDUCTION GEAR UTILIZED ON THE ITEM. SELECT REPLY CODE 10AC58 AXRYD /D/ 09MATERIAL,BONDING,LAMINATED CLOTH LAMINATED CLOTH BONDING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF THE BONDING MATERIAL. SELECT REPLY CODE 10AD09 AXRZG 10RATIO,GEAR,REDUCTION REDUCTION GEAR RATIO THE RATIO OF THE INPUT REVOLUTIONS PER MINUTE TO THE DESIGNED OUTPUT REVOLUTIONS PER MINUTE OF THE REDUCTION GEAR. FULL TEXT WRITE-IN 0 AXSAD 19FORM,ASSEMBLED,LUBE OIL COOLER LUBE OIL COOLER ASSEMBLED FORM AN INDICATION OF THE ASSEMBLED FORM IN WHICH THE LUBE OIL COOLER IS SUPPLIED. SELECT REPLY CODE 10AB28 AXSBD /D/ 07FLY,FRONT FRONT FLY AN INDICATION OF WHETHER OR NOT A FRONT FLY IS PROVIDED. SELECT REPLY CODE 10AB22 AXSCD 19FORM,ASSEMBLED,THROTTLE VALVE THROTTLE VALVE ASSEMBLED FORM AN INDICATION OF THE ASSEMBLED FORM IN WHICH THE THROTTLE VALVE IS SUPPLIED. SELECT REPLY CODE 10AB28 AXSDD 19FORM,ASSEMBLED,GOVERNOR GOVERNOR ASSEMBLED FORM AN INDICATION OF THE ASSEMBLED FORM IN WHICH THE GOVERNOR IS SUPPLIED. SELECT REPLY CODE 10AB28 AXSED /D/ 18TYPE,SYSTEM,FUEL/OXIDIZER FEED FUEL/OXIDIZER FEED SYSTEM TYPE INDICATES THE TYPE OF SYSTEM USED FOR A FUEL AND/OR OXIDIZER FEED BY THE ITEM. SELECT REPLY CODE 10AA96 AXSFD /D/ 07TANK,FUEL/OXIDIZER FUEL/OXIDIZER TANK AN INDICATION OF WHETHER OR NOT A FUEL AND OXIDIZER TANK/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 AXSGD /D/ 07INSTALLATION,TANK TANK INSTALLATION AN INDICATION OF THE INSTALLATION FEATURE OF THE TANK. SELECT REPLY CODE 10AL24 AXSHJ /D/ 10AREA,SURFACE,EFFECTIVE HEATING EFFECTIVE HEATING SURFACE AREA THE EFFECTIVE AREA OF THE HEATING SURFACE. 2D AND 1B MODE REPLY21AC511AC20 AXSJD /D/ 07BINDING,BOTTOM,LEG LEG BOTTOM BINDING AN INDICATION OF WHETHER OR NOT LEG BOTTOM BINDINGS ARE INCLUDED. SELECT REPLY CODE 10AA49 AXSKD /D/ 07FLAPS,GROMMETED,LEG LACING LEG LACING GROMMETED FLAPS AN INDICATION OF WHETHER OR NOT LEG LACING GROMMETED FLAPS ARE INCLUDED. SELECT REPLY CODE 10AA49 AXSLD /D/ 07SUPPORTER,ATHLETIC ATHLETIC SUPPORTER AN INDICATION OF WHETHER OR NOT AN ATHLETIC SUPPORTER IS INCLUDED. SELECT REPLY CODE 10AA49 AXSMD /D/ 19NAME,CLOTH,INTERLINING INTERLINING CLOTH NAME THE NOUN,WITH OR WITHOUT MODIFIERS,BY WHICH THE CLOTH USED TO COVER BETWEEN THE ORDINARY LINING AND THE OUTSIDE FABRIC OF AN ITEM IS KNOWN OR DESIGNATED. SELECT REPLY CODE 10AF82 AXSND /D/ 09MATERIAL,INTERLINING INTERLINING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INTERLINING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AXSPD /D/ 18TYPE,PILE,INTERLINING INTERLINING PILE TYPE INDICATES THE TYPE OF INTERLINING PILE PROVIDED. SELECT REPLY CODE 10AG87 AXSQJ 10AREA,SURFACE,COOLING COOLING SURFACE AREA THE AREA OF THE COOLING SURFACE. 1D AND 1B MODE REPLY11AC51 AXSRJ /D/ 10PRESSURE,OPERATING,MINIMUM MINIMUM OPERATING PRESSURE THE MINIMUM PRESSURE AT WHICH AN ITEM IS DESIGNED TO OPERATE. PLEASE USE MRC BJDT IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1B MODE REPLY11AB18 AXSSD /D/ 07FEATURE,FLAT,RUN RUN FLAT FEATURE AN INDICATION OF WHETHER OR NOT AN INHERENT CHARACTERISTIC WHICH PROVIDES LIMITED OPERATING CAPABILITY AT ZERO INFLATION PRESSURE IS INCLUDED. SELECT REPLY CODE 10AA49 AXSTD /D/ 09MATERIAL,COATING,INTERLINING INTERLINING COATING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE WITH WHICH THE INTERLINING IS COATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AXSWJ 10PRESSURE,WORKING,MAXIMUM STEAM MAXIMUM STEAM WORKING PRESSURE THE MAXIMUM STEAM PRESSURE AT WHICH THE ITEM IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY11AB18 AXSXG /D/ 10LOAD AT SPECIFIED EXTENDED LENGTH,SUPPORTED SUPPORTED LOAD AT SPECIFIED EXTENDED LENGTH THE AMOUNT OF LOAD THE ITEM WILL SUPPORT AT A SPECIFIED EXTENDED LENGTH. FULL TEXT WRITE-IN 0 AXSYD 14SHAPE,ELLIPTIC ELLIPTIC SHAPE THE PHYSICAL ELLIPTIC SHAPE OF THE ITEM. SELECT REPLY CODE 10AF81 AXSZD 08LOCATION,SPRING,HELPER HELPER SPRING LOCATION INDICATES THE LOCATION OF THE HELPER SPRING ON THE ITEM. SELECT REPLY CODE 10AJ91 AXTAH /D/ 18TYPE/STYLE DESIGNATION,LEAF,INDIVIDUAL INDIVIDUAL LEAF TYPE/STYLE DESIGNATION INDICATES THE INDIVIDUAL LEAF TYPE AND STYLE OF WHICH THE ITEM IS COMPOSED. 3D MODE REPLY 33AK542AG123AM40 AXTBJ /D/ 04LENGTH UNDER LOAD LENGTH UNDER LOAD NONE. 2D AND 1B MODE REPLY21AA051AC20 AXTCJ /D/ 04THICKNESS AT BOLT HOLE CENTER THICKNESS AT BOLT HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXTDJ /D/ 04WIDTH AT BOLT HOLE CENTER WIDTH AT BOLT HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXTEA 12QUANTITY,CLIP,REBOUND REBOUND CLIP QUANTITY THE NUMBER OF REBOUND CLIPS PROVIDED. 1A MODE REPLY 0 AXTFA 12QUANTITY,PLATE,TENSION TENSION PLATE QUANTITY THE NUMBER OF TENSION PLATES PROVIDED. 1A MODE REPLY 0 AXTGD 18TYPE,BUSHING BUSHING TYPE INDICATES THE TYPE OF BUSHING PROVIDED. SELECT REPLY CODE 10AM35 AXTHD /D/ 07EYE,MOUNTING,REMOVABLE BRACKET TYPE REMOVABLE BRACKET TYPE MOUNTING EYE AN INDICATION OF WHETHER OR NOT A REMOVABLE BRACKET TYPE MOUNTING EYE IS INCLUDED. SELECT REPLY CODE 10AA49 AXTJJ /D/ 04LENGTH UNDER LOAD TO BOLT HOLE CENTER,AA END AA END LENGTH UNDER LOAD TO BOLT HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXTKJ /D/ 04DIAMETER WITHOUT BUSHING,INSIDE,AA END EYE AA END EYE INSIDE DIAMETER WITHOUT BUSHING NONE. 2D AND 1B MODE REPLY21AA051AC20 AXTLJ /D/ 04DIAMETER WITH BUSHING,INSIDE,AA END EYE AA END EYE INSIDE DIAMETER WITH BUSHING NONE. 2D AND 1B MODE REPLY21AA051AC20 AXTMJ /D/ 04WIDTH AT EYE,AA END AA END WIDTH AT EYE NONE. 2D AND 1B MODE REPLY21AA051AC20 AXTNJ /D/ 04RADIUS,WRAP,AA END AA END WRAP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AXTPJ /D/ 04HEIGHT,CLAMP,AA END AA END CLAMP HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AXTQJ /D/ 04DIAMETER,HOLE,BOLT,AA END CLAMP AA END CLAMP BOLT HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXTRJ /D/ 04HEIGHT,WRAP/BEND,AA END AA END WRAP/BEND HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AXTTJ /D/ 04LENGTH UNDER LOAD TO BOLT HOLE CENTER,BB END BB END LENGTH UNDER LOAD TO BOLT HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXTWJ /D/ 04DIAMETER WITHOUT BUSHING,INSIDE,BB END EYE BB END EYE INSIDE DIAMETER WITHOUT BUSHING NONE. 2D AND 1B MODE REPLY21AA051AC20 AXTXJ /D/ 04DIAMETER WITH BUSHING,INSIDE,BB END EYE BB END EYE INSIDE DIAMETER WITH BUSHING NONE. 2D AND 1B MODE REPLY21AA051AC20 AXTYJ /D/ 04WIDTH AT EYE,BB END BB END WIDTH AT EYE NONE. 2D AND 1B MODE REPLY21AA051AC20 AXTZJ /D/ 04RADIUS,WRAP,BB END BB END WRAP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AXWAJ /D/ 04HEIGHT,CLAMP,BB END BB END CLAMP HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AXWBJ /D/ 04DIAMETER,HOLE,BOLT,BB END CLAMP BB END CLAMP BOLT HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXWCJ /D/ 04HEIGHT,WRAP/BEND,BB END BB END WRAP/BEND HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AXWDJ /D/ 04THICKNESS AT SEAT CENTER THICKNESS AT SEAT CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXWEJ /D/ 04WIDTH AT SEAT CENTER WIDTH AT SEAT CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXWFD /D/ 07GROOVE,ALIGNMENT ALIGNMENT GROOVE AN INDICATION OF WHETHER OR NOT AN ALIGNMENT GROOVE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 AXWGD /D/ 07FEATURE FOR ATTACHING BRACKET,DRILLED DRILLED FEATURE FOR ATTACHING BRACKET AN INDICATION OF WHETHER OR NOT A DRILLED FEATURE FOR AN ATTACHING BRACKET IS INCLUDED. SELECT REPLY CODE 10AA49 AXWHJ 04WIDTH,MATERIAL MATERIAL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MATERIAL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AXWJD 18TYPE,DEVICE,FASTENING FASTENING DEVICE TYPE INDICATES THE TYPE OF FASTENING DEVICE PROVIDED. SELECT REPLY CODE 10AE36 AXWKD /D/ 07HOLE,BASE BASE HOLE AN INDICATION OF WHETHER OR NOT A BASE HOLE IS INCLUDED. SELECT REPLY CODE 10AA49 AXWLJ 04DIAMETER,HOLE,BASE BASE HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BASE HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AXWMJ 04WIDTH BETWEEN LEGS WIDTH BETWEEN LEGS NONE. 2D AND 1B MODE REPLY21AA051AC20 AXWNJ 04DIAMETER,HOLE,LEG LEG HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXWPJ 04WIDTH,END,ATTACHING ATTACHING END WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXWQJ 04DIAMETER,HOLE,ATTACHING END ATTACHING END HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXWRD /D/ 08LOCATION,MATERIAL,COATING,INTERLINING INTERLINING COATING MATERIAL LOCATION INDICATES THE LOCATION OF THE INTERLINING TO WHICH A COATING HAS BEEN APPLIED. SELECT REPLY CODE 10AJ91 AXWSD /D/ 19PROTECTION,ENVIRONMENTAL,INTERLINING CLOTH INTERLINING CLOTH ENVIRONMENTAL PROTECTION THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT THE INTERLINING CLOTH IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY. SELECT REPLY CODE 10AA65 AXWTJ 10CAPACITY,STORAGE STORAGE CAPACITY THE STORAGE CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 AXWWJ /D/ 10AREA,SURFACE,EFFECTIVE COOLING EFFECTIVE COOLING SURFACE AREA THE EFFECTIVE AREA OF THE COOLING SURFACE. 2D AND 1B MODE REPLY21AC511AC20 AXWXD /D/ 07LINING LINING AN INDICATION OF WHETHER OR NOT A LINING IS FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AA55 AXWYD 18TYPE,SYSTEM,COOLING COOLING SYSTEM TYPE INDICATES THE TYPE OF COOLING SYSTEM FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AB75 AXWZD /D/ 01COLOR,LINING LINING COLOR THE HUE OR TINT OF THE LINING. SELECT REPLY CODE 10AD06 AXXAD /D/ 08LOCATION,MATERIAL,COATING,LINING LINING COATING MATERIAL LOCATION INDICATES THE LOCATION OF THE LINING TO WHICH A COATING HAS BEEN APPLIED. SELECT REPLY CODE 10AJ91 AXXBD /D/ 09MATERIAL,COATING,LINER LINER COATING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE WITH WHICH THE LINER IS COATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AXXCD /D/ 08SOCATION,MATERIAL,COATING,LINER LINER COATING MATERIAL SOCATION INDICATES THE LOCATION OF THE LINER TO WHICH A COATING HAS BEEN APPLIED. SELECT REPLY CODE 10AJ91 AXXDA 12QUANTITY,CHAMBER,THRUST THRUST CHAMBER QUANTITY THE NUMBER OF THRUST CHAMBERS PROVIDED ON THE ITEM. 1A MODE REPLY 0 AXXED /D/ 11METHOD,CLOSING/SUPPORTING,WAIST WAIST CLOSING/SUPPORTING METHOD THE MEANS BY WHICH THE OPENING IS CLOSED AND/OR SUPPORTED AT THE WAIST. SELECT REPLY CODE 10AF69 AXXFJ /D/ 04LENGTH FROM TOP OF WAIST TO LEG BOTTOM LENGTH FROM TOP OF WAIST TO LEG BOTTOM A MEASUREMENT OF THE LONGEST DIMENSION FROM THE TOP OF THE WAIST TO THE LEG BOTTOM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AXXGD /D/ 19PATTERN,FABRIC,REVERSIBLE REVERSIBLE FABRIC PATTERN AN ARTISTIC OR MECHANICAL DESIGN OR FIGURE THAT IS IMPRINTED ON,EMBODIED IN,OR OTHERWISE CAUSED TO BECOME AN INTEGRAL OR APPARENT PART OF THE REVERSIBLE FABRIC. SELECT REPLY CODE 10AF83 AXXHD /D/ 01COLOR,BACKGROUND,REVERSIBLE REVERSIBLE BACKGROUND COLOR THE HUE OR TINT OF THE REVERSIBLE BACKGROUND. SELECT REPLY CODE 10AD06 AXXJD /D/ 19SOURCE,SHADE,REVERSIBLE BACKGROUND REVERSIBLE BACKGROUND SHADE SOURCE THE NAME OF THE REFERENCE SOURCE OF THE REVERSIBLE BACKGROUND SHADE IDENTIFICATION DESIGNATOR. SELECT REPLY CODE 10AF94 AXXKA /D/ 12QUANTITY,CLOSURE CLOSURE QUANTITY THE NUMBER OF CLOSURES INCLUDED ON THE ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1A MODE REPLY 0 AXXLD 08LOCATION,DEVICE,CLOSING CLOSING DEVICE LOCATION INDICATES THE LOCATION OF THE CLOSING DEVICE ON THE ITEM. SELECT REPLY CODE 10AJ91 AXXMD /D/ 18TYPE,UNIT,SERVICE SERVICE UNIT TYPE INDICATES THE TYPE OF SERVICE UNIT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 AXXND /D/ 07COATING,REFLECTORIZED REFLECTORIZED COATING AN INDICATION OF WHETHER OR NOT A REFLECTORIZED COATING IS INCLUDED. SELECT REPLY CODE 10AA49 AXXPA /D/ 12QUANTITY,OPENING,PLACKET PLACKET OPENING QUANTITY THE NUMBER OF PLACKET OPENINGS INCLUDED IN THE ITEM. 1A MODE REPLY 0 AXXQD /D/ 08LOCATION,PLACKET PLACKET LOCATION INDICATES THE LOCATION OF THE PLACKET/S/ IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 AXXRD /D/ 11METHOD,CLOSING,PLACKET PLACKET CLOSING METHOD THE MEANS BY WHICH THE PLACKET OPENING IS CLOSED. SELECT REPLY CODE 10AF69 AXXSD /D/ 19NAME,CLOTH,TRIM TRIM CLOTH NAME THE NOUN,WITH OR WITHOUT MODIFIERS,BY WHICH THE CLOTH USED FOR THE TRIM ON AN ITEM IS KNOWN OR DESIGNATED. SELECT REPLY CODE 10AF82 AXXTD /D/ 09MATERIAL,TRIM TRIM MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TRIM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AXXWD /D/ 08LOCATION,TRIM TRIM LOCATION INDICATES THE LOCATION OF THE ITEM TO WHICH A TRIM HAS BEEN APPLIED. SELECT REPLY CODE 10AJ91 AXXXD /D/ 08LOCATION,PAD PAD LOCATION INDICATES THE LOCATION OF THE PAD IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 AXXYJ /D/ 04THICKNESS,MATERIAL,PAD PAD MATERIAL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE PAD MATERIAL,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 AXXZD /D/ 11METHOD,ATTACHMENT,PAD PAD ATTACHMENT METHOD THE MEANS BY WHICH THE PAD IS ATTACHED TO THE ITEM. SELECT REPLY CODE 10AF69 AXYAD /D/ 07SUSPENDERS SUSPENDERS AN INDICATION OF WHETHER OR NOT SUSPENDERS ARE INCLUDED. SELECT REPLY CODE 10AA49 AXYBD /D/ 07REMOVABILITY,SUSPENDER SUSPENDER REMOVABILITY AN INDICATION OF WHETHER OR NOT THE SUSPENDERS ARE REMOVABLE. SELECT REPLY CODE 10AC29 AXYCD /D/ 07BUTTONHOLES FOR ATTACHING TO SUSPENDERS BUTTONHOLES FOR ATTACHING TO SUSPENDERS AN INDICATION OF WHETHER OR NOT BUTTONHOLES FOR ATTACHING TO SUSPENDERS ARE INCLUDED. SELECT REPLY CODE 10AA49 AXYDD /D/ 07LOOPS,SUSPENDER SUSPENDER LOOPS AN INDICATION OF WHETHER OR NOT SUSPENDER LOOPS ARE INCLUDED. SELECT REPLY CODE 10AA49 AXYED /D/ 18TYPE,GARMENT GARMENT TYPE INDICATES THE TYPE OF GARMENT FURNISHED. SELECT REPLY CODE 10AH80 AXYFD /D/ 07FEATURE,IMPREGNATION IMPREGNATION FEATURE AN INDICATION OF WHETHER OR NOT AN IMPREGNATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AXYGD /D/ 07ASSEMBLY,STRAP,CROTCH/STIRRUP CROTCH/STIRRUP STRAP ASSEMBLY AN INDICATION OF WHETHER OR NOT A CROTCH AND STIRRUP STRAP ASSEMBLY IS INCLUDED. SELECT REPLY CODE 10AA49 AXYHD /D/ 09MATERIAL,STRAP,CROTCH/STIRRUP CROTCH/STIRRUP STRAP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CROTCH AND STIRRUP STRAP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AXYJJ /D/ 04WIDTH,STRAP,CROTCH/STIRRUP CROTCH/STIRRUP STRAP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CROTCH AND STIRRUP STRAP,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AXYKD /D/ 11METHOD,ATTACHMENT,CROTCH/STIRRUP STRAP CROTCH/STIRRUP STRAP ATTACHMENT METHOD THE MEANS BY WHICH THE CROTCH AND STIRRUP STRAP IS ATTACHED TO THE ITEM. SELECT REPLY CODE 10AF69 AXYLJ 04DIAMETER,PORTION,UNTHREADED,LEG LEG UNTHREADED PORTION DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXYMJ 04DIAMETER,SURFACE,BEARING BEARING SURFACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXYNJ 04LENGTH,PORTION,UNTHREADED,LEG LEG UNTHREADED PORTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXYPD /D/ 07LEG,THREADED THREADED LEG AN INDICATION OF WHETHER OR NOT A THREADED LEG(S) IS INCLUDED. SELECT REPLY CODE 10AA49 AXYQD /D/ 09MATERIAL,BUSHING BUSHING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BUSHING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AXYRD /D/ 07HOLE,SPLINED SPLINED HOLE AN INDICATION OF WHETHER OR NOT A SPLINED HOLE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 AXYSD 18TYPE,SPLINE SPLINE TYPE INDICATES THE TYPE OF SPLINE PROVIDED. SELECT REPLY CODE 10AA85 AXYTJ 04WIDTH,GROOVE,FIRST LOCKING FIRST LOCKING GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXYWJ 04DEPTH,GROOVE,FIRST LOCKING FIRST LOCKING GROOVE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXYXJ 04WIDTH,GROOVE,SECOND LOCKING SECOND LOCKING GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXYYJ 04DEPTH,GROOVE,SECOND LOCKING SECOND LOCKING GROOVE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXYZJ 04WIDTH,GROOVE,FIRST GREASE RELIEF FIRST GREASE RELIEF GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXZAJ 04LENGTH,GROOVE,FIRST GREASE RELIEF FIRST GREASE RELIEF GROOVE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXZBJ 04DEPTH,GROOVE,FIRST GREASE RELIEF FIRST GREASE RELIEF GROOVE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXZCJ /D/ 04WIDTH,GROOVE,SECOND GREASE RELIEF SECOND GREASE RELIEF GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXZDJ /D/ 04LENGTH,GROOVE,SECOND GREASE RELIEF SECOND GREASE RELIEF GROOVE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXZEJ /D/ 04DEPTH,GROOVE,SECOND GREASE RELIEF SECOND GREASE RELIEF GROOVE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXZFJ /D/ 04DIAMETER PERPENDICULAR TO PIN AXIS,FIRST HOLE FIRST HOLE DIAMETER PERPENDICULAR TO PIN AXIS NONE. 2D AND 1B MODE REPLY21AA051AC20 AXZGJ /D/ 04DIAMETER PERPENDICULAR TO PIN AXIS,SECOND HOLE SECOND HOLE DIAMETER PERPENDICULAR TO PIN AXIS NONE. 2D AND 1B MODE REPLY21AA051AC20 AXZHJ /D/ 04DISTANCE FROM END TO FIRST HOLE CENTER PERPENDICULAR TO PIN AXIS DISTANCE FROM END TO FIRST HOLE CENTER PERPENDICULAR TO PIN AXIS NONE. 2D AND 1B MODE REPLY21AA051AC20 AXZJJ /D/ 04DISTANCE FROM END TO SECOND HOLE CENTER PERPENDICULAR TO PIN AXIS DISTANCE FROM END TO SECOND HOLE CENTER PERPENDICULAR TO PIN AXIS NONE. 2D AND 1B MODE REPLY21AA051AC20 AXZKJ /D/ 04DISTANCE FROM END TO FIRST LOCKING GROOVE CENTER DISTANCE FROM END TO FIRST LOCKING GROOVE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXZLJ /D/ 04DISTANCE FROM END TO SECOND LOCKING GROOVE CENTER DISTANCE FROM END TO SECOND LOCKING GROOVE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AXZMJ 04DISTANCE FROM END TO FIRST GREASE RELIEF GROOVE DISTANCE FROM END TO FIRST GREASE RELIEF GROOVE NONE. 2D AND 1B MODE REPLY21AA051AC20 AXZNJ /D/ 04DISTANCE FROM END TO SECOND GREASE RELIEF GROOVE DISTANCE FROM END TO SECOND GREASE RELIEF GROOVE NONE. 2D AND 1B MODE REPLY21AA051AC20 AXZPJ 04LENGTH,FLAT,END END FLAT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AXZQJ /D/ 04WIDTH ACROSS END FLATS WIDTH ACROSS END FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 AXZRD /D/ 07ACCOMMODATION,THREAD,LUBRICATION FITTING LUBRICATION FITTING THREAD ACCOMMODATION AN INDICATION OF WHETHER OR NOT A LUBRICATION FITTING THREAD ACCOMMODATION IS INCLUDED. SELECT REPLY CODE 10AA49 AXZSJ /D/ 13THREAD MINIMUM PITCH DIAMETER THREAD MINIMUM PITCH DIAMETER THE MINIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD. 1D AND 1B MODE REPLY11AA05 AXZTJ /D/ 13THREAD LENGTH,END END THREAD LENGTH A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS OF THE END. 2D AND 1B MODE REPLY21AA051AC20 AXZWA /D/ 13THREAD SIZE,END END THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE END. 1A MODE REPLY 0 AXZXD /D/ 13THREAD SERIES,END END THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF AN END. SELECT REPLY CODE 10AH06 AXZYA /D/ 13THREAD CLASS,END END THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE,AND AN EXTERNAL OR INTERNAL THREAD. 1A MODE REPLY 0 AXZZJ /D/ 13THREAD MINIMUM PITCH DIAMETER,END END THREAD MINIMUM PITCH DIAMETER THE MINIMUM PITCH DIAMETER LIMITS OF A STRAIGHT END SCREW THREAD. 1D AND 1B MODE REPLY11AA05 AYAAG /D/ 10FINISH RATING,SPECIFIED,BEARING SURFACE BEARING SURFACE SPECIFIED FINISH RATING THE SPECIFIED FINISH RATING OF THE BEARING SURFACE. FULL TEXT WRITE-IN 0 AYABJ /D/ 04DIAMETER IN WHICH SPRING MUST WORK,BORE BORE DIAMETER IN WHICH SPRING MUST WORK NONE. 2D AND 1B MODE REPLY21AA051AC20 AYACJ /D/ 04DIAMETER OVER WHICH SPRING MUST WORK,OUTSIDE,ROD ROD OUTSIDE DIAMETER OVER WHICH SPRING MUST WORK NONE. 2D AND 1B MODE REPLY21AA051AC20 AYADB /D/ 19DIMENSION BETWEEN COIL ENDS IN DEG,ANGULAR ANGULAR DIMENSION BETWEEN COIL ENDS IN DEG NONE. 1B MODE REPLY 0 AYAEJ /D/ 04DIAMETER,OUTSIDE,COIL FREE POSITION COIL FREE POSITION OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AYAFD /D/ 08LOCATION,STRAP,CROTCH/STIRRUP CROTCH/STIRRUP STRAP LOCATION INDICATES THE LOCATION OF THE CROTCH AND STIRRUP STRAP IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 AYAGD /D/ 07STRAP TO ACCOMMODATE LETDOWN ROPE,SEAT SEAT STRAP TO ACCOMMODATE LETDOWN ROPE AN INDICATION OF WHETHER OR NOT A SEAT STRAP TO ACCOMMODATE THE LETDOWN ROPE IS INCLUDED. SELECT REPLY CODE 10AA49 AYAHD /D/ 09MATERIAL,STRAP,SEAT SEAT STRAP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SEAT STRAP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AYAJJ /D/ 04WIDTH,STRAP,SEAT SEAT STRAP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SEAT STRAP,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AYAKG /D/ 19TITLE,BOOK,INSTRUCTION INSTRUCTION BOOK TITLE AN INSTRUCTION BOOK SPECIFICALLY DESIGNED FOR USE WITH THE ITEM OF SUPPLY. FULL TEXT WRITE-IN 0 AYALD /D/ 11METHOD,ATTACHMENT,SEAT STRAP SEAT STRAP ATTACHMENT METHOD THE MEANS BY WHICH THE SEAT STRAP IS ATTACHED TO THE ITEM. SELECT REPLY CODE 10AF69 AYAMD /D/ 08LOCATION,STRAP,SEAT SEAT STRAP LOCATION INDICATES THE LOCATION OF THE SEAT STRAP IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 AYAND /D/ 07OPENING,SIDE SIDE OPENING AN INDICATION OF WHETHER OR NOT SIDE OPENINGS ARE INCLUDED. SELECT REPLY CODE 10AA49 AYAPG /D/ 18TYPE,VESSEL VESSEL TYPE INDICATES THE TYPE OF VESSEL FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 AYAQD /D/ 07PASS THROUGH OPENING,SIDE SIDE PASS THROUGH OPENING AN INDICATION OF WHETHER OR NOT A SIDE PASS THROUGH OPENING IS INCLUDED. SELECT REPLY CODE 10AA49 AYARA /D/ 12QUANTITY PER VESSEL QUANTITY PER VESSEL THE NUMBER OF UNITS PROVIDED,PER VESSEL. 1A MODE REPLY 0 AYASH /D/ 08LOCATION AND METHOD,CLOSURE,SIDE SIDE CLOSURE LOCATION AND METHOD INDICATES THE LOCATION OF THE SIDE CLOSURE AND THE MEANS BY WHICH IT IS CLOSED. 2D MODE REPLY 23AJ912AF69 AYATD /D/ 07FLAP,OUTLET,PIGTAIL PIGTAIL OUTLET FLAP AN INDICATION OF WHETHER OR NOT A FLAP FOR PIGTAIL OUTLET IS PROVIDED. SELECT REPLY CODE 10AB22 AYAWG /D/ 10WATER RATE AT FULL LOAD WATER RATE AT FULL LOAD THE MEASURED RATE OF WATER AT FULL LOAD. FULL TEXT WRITE-IN 0 AYAXJ /D/ 04HEIGHT,OVERALL,TURBINE TURBINE OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE TURBINE. 2D AND 1B MODE REPLY21AA051AC20 AYAYD 11METHOD,ATTACHMENT ATTACHMENT METHOD THE MEANS USED TO ATTACH THE ITEM. SELECT REPLY CODE 10AF69 AYAZD /D/ 07BACK,YOKE YOKE BACK AN INDICATION OF WHETHER OR NOT A YOKE BACK IS INCLUDED. SELECT REPLY CODE 10AA49 AYBAD /D/ 07PATCHES,KNEE,PROTECTIVE PROTECTIVE KNEE PATCHES AN INDICATION OF WHETHER OR NOT PROTECTIVE KNEE PATCHES ARE INCLUDED. SELECT REPLY CODE 10AA49 AYBBJ /D/ 04LENGTH AT BASE,OVERALL,TURBINE TURBINE OVERALL LENGTH AT BASE THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE TURBINE AT THE BASE. 2D AND 1B MODE REPLY21AA051AC20 AYBCJ /D/ 04WIDTH AT BASE,OVERALL,TURBINE TURBINE OVERALL WIDTH AT BASE AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TURBINE AT THE BASE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AYBDA /D/ 19NUMBER,ITEM,COMPONENT DOCUMENT COMPONENT DOCUMENT ITEM NUMBER THE NUMBER USED TO IDENTIFY THE ITEM IN THE COMPONENT DOCUMENT. 1A MODE REPLY 0 AYBEJ 04HEIGHT,OVERALL,ENGINE ENGINE OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE ENGINE. 2D AND 1B MODE REPLY21AA051AC20 AYBFJ 04LENGTH,OVERALL,ENGINE ENGINE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ENGINE. 2D AND 1B MODE REPLY21AA051AC20 AYBGJ 04WIDTH,OVERALL,ENGINE ENGINE OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ENGINE,IN DISTICTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AYBHJ /D/ 04HEIGHT,OVERALL,POWER UNIT POWER UNIT OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE POWER UNIT. 2D AND 1B MODE REPLY21AA051AC20 AYBJJ /D/ 04LENGTH,OVERALL,POWER UNIT POWER UNIT OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE POWER UNIT. 2D AND 1B MODE REPLY21AA051AC20 AYBKJ /D/ 04WIDTH,OVERALL,POWER UNIT POWER UNIT OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE POWER UNIT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AYBLJ /D/ 10CLEARANCE,DISMANTLING,REQUIRED REQUIRED DISMANTLING CLEARANCE AN INDICATION OF THE CLEARANCE REQUIRED FOR DISMANTLING THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 AYBMG 19INSCRIPTION INSCRIPTION THE LETTERING OR DESIGN ON THE ITEM,OR THAT IS THE ITEM. FULL TEXT WRITE-IN 0 AYBND /D/ 09MATERIAL,YARN YARN MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE YARN IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AYBPB /D/ 10PERCENT,YARN,MIXED MIXED YARN PERCENT AN INDICATION OF THE CONTENT OF THE VARIOUS AMOUNTS OF MIXED YARN COMPRISING THE ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 AYBQA /D/ 03DESIGNATOR,SIZE,YARN YARN SIZE DESIGNATOR A NUMBER,LETTER,AND/OR WORD DESIGNATION INDICATING THE SIZE BY WHICH THE YARN IS IDENTIFIED. 1A MODE REPLY 0 AYBRD /D/ 19PROTECTION,ENVIRONMENTAL,YARN YARN ENVIRONMENTAL PROTECTION THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT THE YARN IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY. SELECT REPLY CODE 10AA65 AYBSG /D/ 18TYPE/MODEL NUMBER,ENGINE ENGINE TYPE/MODEL NUMBER INDICATES THE TYPE OF ENGINE,AND ITS MODEL NUMBER. FULL TEXT WRITE-IN 0 AYBTD /D/ 07CHARACTERISTIC,KNITTED KNITTED CHARACTERISTIC AN INDICATION OF WHETHER OR NOT A KNITTED CHARACTERISTIC IS INCLUDED. SELECT REPLY CODE 10AA49 AYBWD /D/ 19PROPELLANT FOR WHICH DESIGNED,ENGINE,ROCKET ROCKET ENGINE PROPELLANT FOR WHICH DESIGNED THE PROPELLANT FOR WHICH THE ROCKET ENGINE IS DESIGNED. SELECT REPLY CODE 10AB75 AYBXD /D/ 07FEATURE,USAGE,WHEEL WHEEL USAGE FEATURE AN INDICATION OF WHETHER OR NOT A WHEEL USAGE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AYBYJ 04DIAMETER ACCOMMODATED,WHEEL WHEEL DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR A WHEEL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYBZJ 04WIDTH ACCOMMODATED,WHEEL WHEEL WIDTH ACCOMMODATED A MEASUREMEMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ACCOMMODATION FOR A WHEEL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AYCAG /D/ 03DESIGNATOR,MONOGRAM MONOGRAM DESIGNATOR A DEVICE,SYMBOL,OR FIGURE ADOPTED AND USED AS AN IDENIFYING MARK. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. FULL TEXT WRITE-IN 0 AYCBD 18TYPE,STRAINER,SUCTION SUCTION STRAINER TYPE INDICATES THE TYPE OF SUCTION STRAINER PROVIDED. SELECT REPLY CODE 10AA21 AYCCA 12QUANTITY,JET JET QUANTITY THE NUMBER OF JETS PROVIDED. 1A MODE REPLY 0 AYCDD /D/ 09MATERIAL,JET JET MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE JET IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AYCEA /D/ 12QUANTITY,FITTING FITTING QUANTITY THE NUMBER OF FITTINGS PROVIDED. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1A MODE REPLY 0 AYCFG /D/ 19NAME,FITTING FITTING NAME THE NAME ASSIGNED TO THE FITTING(S). MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. FULL TEXT WRITE-IN 0 AYCGJ 10DELIVERY RATE PER HOUR DELIVERY RATE PER HOUR THE MAXIMUM OUTPUT DELIVERED BY THE ITEM PER HOUR. 1D AND 1B MODE REPLY11AB10 AYCHJ /D/ 10PRESSURE RATING,CUTOUT,TANK TANK CUTOUT PRESSURE RATING THE RATED PRESSURE AT WHICH THE TANK CUTOUT IS SET. 2D AND 1B MODE REPLY22AB161AC20 AYCJJ /D/ 10PRESSURE RATING,CUT-IN,TANK TANK CUT-IN PRESSURE RATING THE RATED PRESSURE AT WHICH THE TANK CUT-IN IS SET. 2D AND 1B MODE REPLY22AB161AC20 AYCKD /D/ 07FEATURE,FLOW,PERIPHERAL PERIPHERAL FLOW FEATURE AN INDICATION OF WHETHER OR NOT A PERIPHERAL FLOW FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AYCLJ 04SIZE,SUCTION,INLET INLET SUCTION SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSION(S) OF THE INLET SUCTION. 1D AND 1B MODE REPLY11AA05 AYCMD /D/ 07FEATURE,RESISTANT,CORROSION CORROSION RESISTANT FEATURE AN INDICATION OF WHETHER OR NOT A CORROSION RESISTANT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AYCND /D/ 07FEATURE,CONTROL,AUTOMATIC AIR VOLUME AUTOMATIC AIR VOLUME CONTROL FEATURE AN INDICATION OF WHETHER OR NOT AN AUTOMATIC AIR VOLUME CONTROL FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AYCPD /D/ 07FEATURE,MOUNTED,UNIT UNIT MOUNTED FEATURE AN INDICATION OF WHETHER OR NOT A UNIT MOUNTED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AYCQA 12QUANTITY,CONNECTION,SERVICE SERVICE CONNECTION QUANTITY THE NUMBER OF SERVICE CONNECTIONS PROVIDED. 1A MODE REPLY 0 AYCRJ 04SIZE,CONNECTION,SERVICE SERVICE CONNECTION SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSION(S) OF THE SERVICE CONNECTION. 1D AND 1B MODE REPLY11AA05 AYCSD /D/ 07FEATURE,CONVERSION,DEEP WELL DEEP WELL CONVERSION FEATURE AN INDICATION OF WHETHER OR NOT A DEEP WELL CONVERSION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AYCTD /D/ 07FEATURE,SERVICE,SALT WATER SALT WATER SERVICE FEATURE AN INDICATION OF WHETHER OR NOT A SALT WATER SERVICE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AYCWG 19NAME,MANUFACTURER,PUMP PUMP MANUFACTURER NAME THE NAME OF THE PUMP MANUFACTURER. FULL TEXT WRITE-IN 0 AYCXG /D/ 19NUMBER,IDENTIFYING,PUMP MANUFACTURER PUMP MANUFACTURER IDENTIFYING NUMBER THE NUMBER USED BY THE MANUFACTURER FOR IDENTIFYING THE PUMP. FULL TEXT WRITE-IN 0 AYCYD 13THREAD LOCATION,CONNECTION,SUCTION SUCTION CONNECTION THREAD LOCATION THE LOCATION OF THE THREADS ON THE SUCTION CONNECTION. SELECT REPLY CODE 10AJ91 AYCZJ /D/ 04SIZE,PIPE,SUCTION CONNECTION SUCTION CONNECTION PIPE SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSION(S) OF THE SUCTION CONNECTION PIPE. 1D AND 1B MODE REPLY11AA05 AYDAD 13THREAD SERIES DESIGNATOR,CONNECTION,SUCTION SUCTION CONNECTION THREAD SERIES DESIGNATOR A DESIGNATOR INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF THE SUCTION CONNECTION. SELECT REPLY CODE 10AH06 AYDBD 18TYPE,FLANGE,SUCTION CONNECTION SUCTION CONNECTION FLANGE TYPE INDICATES THE TYPE OF SUCTION CONNECTION FLANGE PROVIDED. SELECT REPLY CODE 10AA78 AYDCJ 04THICKNESS,FLANGE,SUCTION CONNECTION SUCTION CONNECTION FLANGE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE SUCTION CONNECTION FLANGE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AYDDJ 04DIAMETER,CIRCLE,BOLT,SUCTION CONNECTION FLANGE SUCTION CONNECTION FLANGE BOLT CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SUCTION CONNECTION FLANGE BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYDEA 12QUANTITY,HOLE,BOLT,SUCTION CONNECTION FLANGE SUCTION CONNECTION FLANGE BOLT HOLE QUANTITY THE NUMBER OF SUCTION CONNECTION FLANGE BOLT HOLES PROVIDED. 1A MODE REPLY 0 AYDFJ 04DIAMETER,HOLE,BOLT,SUCTION CONNECTION FLANGE SUCTION CONNECTION FLANGE BOLT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SUCTION CONNECTION FLANGE BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYDGJ 04SIZE,PIPE,SUCTION CONNECTION FLANGE SUCTION CONNECTION FLANGE PIPE SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSION/S/ OF THE SUCTION CONNECTION FLANGE PIPE. 1D AND 1B MODE REPLY11AA05 AYDHA /D/ 16STYLE,DISCONNECT,QUICK,SUCTION CONNECTION SUCTION CONNECTION QUICK DISCONNECT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SUCTION CONNECTION QUICK DISCONNECT. 1A MODE REPLY 0 AYDJG /D/ 04SIZE,DISCONNECT,QUICK,SUCTION CONNECTION SUCTION CONNECTION QUICK DISCONNECT SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSION(S) OF THE SUCTION CONNECTION QUICK DISCONNECT. FULL TEXT WRITE-IN 0 AYDKJ 04SIZE,PIPE,DISCHARGE CONNECTION DISCHARGE CONNECTION PIPE SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSION(S) OF THE DISCHARGE CONNECTION PIPE. 1D AND 1B MODE REPLY11AA05 AYDLJ 04DIAMETER,CIRCLE,BOLT,DISCHARGE CONNECTION FLANGE DISCHARGE CONNECTION FLANGE BOLT CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DISCHARGE CONNECTION FLANGE BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYDMA 12QUANTITY,HOLE,BOLT,DISCHARGE CONNECTION FLANGE DISCHARGE CONNECTION FLANGE BOLT HOLE QUANTITY THE NUMBER OF BOLT HOLES IN THE DISCHARGE CONNECTION FLANGE. 1A MODE REPLY 0 AYDNJ 04DIAMETER,HOLE,BOLT,DISCHARGE CONNECTION FLANGE DISCHARGE CONNECTION FLANGE BOLT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DISCHARGE CONNECTION FLANGE BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYDPJ 04SIZE,PIPE,DISCHARGE CONNECTION FLANGE DISCHARGE CONNECTION FLANGE PIPE SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSION(S) OF THE DISCHARGE CONNECTION FLANGE PIPE. 1D AND 1B MODE REPLY11AA05 AYDQA /D/ 16STYLE,DISCONNECT,QUICK,DISCHARGE CONNECTION DISCHARGE CONNECTION QUICK DISCONNECT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE DISCHARGE CONNECTION QUICK DISCONNECT. 1A MODE REPLY 0 AYDRG 19IDENTIFICATION,DOCUMENT DOCUMENT IDENTIFICATION THE NUMBER OR SYMBOL/S/ USED TO IDENTIFY THE DOCUMENT. FULL TEXT WRITE-IN 0 AYDSG 19NAME,ITEM,END END ITEM NAME THE APPROVED ITEM NAME OR PART NAME OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART. FULL TEXT WRITE-IN 0 AYDTJ 10AREA,SURFACE,BRAKING BRAKING SURFACE AREA A MEASUREMENT OF THE AMOUNT OF BRAKING SURFACE AREA. 2D AND 1B MODE REPLY21AC511AC20 AYDWD 18TYPE,ACTUATOR ACTUATOR TYPE INDICATES THE TYPE OF ACTUATOR PROVIDED. SELECT REPLY CODE 10AC58 AYDXD /D/ 07COLLAR WITH EYELETS FOR ATTACHING TABS COLLAR WITH EYELETS FOR ATTACHING TABS AN INDICATION OF WHETHER OR NOT A COLLAR WITH EYELETS IS INCLUDED FOR ATTACHING TABS. SELECT REPLY CODE 10AA49 AYDYJ /D/ 04SIZE,SLEEVE,FULL LENGTH FULL LENGTH SLEEVE SIZE DESIGNATES THE NUMERIC SIZE OF THE FULL LENGTH SLEEVE. 1D AND 1B MODE REPLY11AA05 AYDZD 18TYPE,SPEED SPEED TYPE INDICATES THE TYPE OF SPEED FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL77 AYEAD /D/ 18TYPE,SLEEVE,GARMENT GARMENT SLEEVE TYPE INDICATES THE TYPE OF GARMENT SLEEVE PROVIDED. SELECT REPLY CODE 10AF89 AYEBJ 10TEMP,AMBIENT,ACTUATOR RATED ACTUATOR RATED AMBIENT TEMP THE TEMPERATURE OF THE MEDIUM SURROUNDING THE ACTUATOR AT WHICH IT CAN BE OPERATED CONTINUOUSLY. 2D AND 1B MODE REPLY21AB361AC20 AYECD /D/ 11METHOD,CLOSURE,SLEEVE CUFF SLEEVE CUFF CLOSURE METHOD THE MEANS BY WHICH THE SLEEVE CUFF OPENING IS CLOSED. SELECT REPLY CODE 10AF69 AYEDA /D/ 12QUANTITY,BUTTON,SLEEVE CUFF SLEEVE CUFF BUTTON QUANTITY THE NUMBER OF BUTTONS ON THE SLEEVE CUFF. 1A MODE REPLY 0 AYEEJ 10RISE,TEMP,ACUTATOR OPERATION ACTUATOR OPERATION TEMP RISE THE INCREASE IN THE TEMPERATURE OF THE ACTUATOR DURING OPERATION. 2D AND 1B MODE REPLY21AB361AD63 AYEFD /D/ 19ARRANGEMENT,BUTTON BUTTON ARRANGEMENT AN INDICATION OF THE WAY THE BUTTONS ARE ARRANGED ON THE ITEM. SELECT REPLY CODE 10AH86 AYEGD /D/ 07GUSSET,SLEEVE,PROTECTIVE PROTECTIVE SLEEVE GUSSET AN INDICATION OF WHETHER OR NOT A PROTECTIVE SLEEVE GUSSET IS INCLUDED. SELECT REPLY CODE 10AA49 AYEHJ /D/ 04SIZE,NECK,GARMENT GARMENT NECK SIZE THE NECK SIZE DESIGNATION OF THE GARMENT AS DETERMINED BY THE MANUFACTURER. 1D AND 1B MODE REPLY11AA05 AYEJD 18TYPE,OPENING,NECK NECK OPENING TYPE INDICATES THE TYPE OF NECK OPENING PROVIDED. SELECT REPLY CODE 10AM58 AYEKJ 10CYCLE,DUTY,INTERMITTENT OPERATION INTERMITTENT OPERATION DUTY CYCLE THE MAXIMUM OPERATING ON TIME AND THE MINIMUM OFF TIME FOR A COMPLETE CYCLE OF AN ITEM. 3D AND 1B MODE REPLY32AB491AC201AK45 AYELD /D/ 18TYPE,OPENING,GARMENT GARMENT OPENING TYPE INDICATES THE TYPE OF GARMENT OPENING ON THE ITEM. SELECT REPLY CODE 10AM58 AYEMD /D/ 07BELT BELT AN INDICATION OF WHETHER OR NOT A BELT IS INCLUDED. SELECT REPLY CODE 10AA49 AYEND /D/ 18TYPE,TERMINAL,SECONDARY SECONDARY TERMINAL TYPE INDICATES THE TYPE OF TERMINALS INCLUDED IN THE DISTRIBUTOR CAP TO ACCOMMODATE THE SPARK PLUG WIRES. SELECT REPLY CODE 10AA58 AYEPD 13THREAD SERIES,ACCOMMODATION,SPARK PLUG TERMINAL SPARK PLUG TERMINAL ACCOMMODATION THREAD SERIES A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER OF THE SPARK PLUG TERMINAL ACCOMMODATION. SELECT REPLY CODE 10AH06 AYEQD /D/ 13THREAD DIRECTION,ACCOMMODATION,SECONDARY TERMINAL SECONDARY TERMINAL ACCOMMODATION THREAD DIRECTION THE DIRECTION OF THE SECONDARY TERMINAL ACCOMMODATION THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 AYERD /D/ 18TYPE,TERMINAL,COIL COIL TERMINAL TYPE INDICATES THE TYPE OF TERMINALS INCLUDED IN THE DISTRIBUTOR CAP TO ACCOMMODATE THE COIL WIRE. SELECT REPLY CODE 10AA58 AYESJ /D/ 04LENGTH,SHIRT SHIRT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION TAKEN FROM UNDER THE COLLAR SEAM,AT CENTER,TO THE BOTTOM EDGE OF THE SHIRT,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AYETD /D/ 13THREAD SERIES,ACCOMMODATION,COIL TERMINAL COIL TERMINAL ACCOMMODATION THREAD SERIES A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER OF THE COIL TERMINAL ACCOMMODATION. SELECT REPLY CODE 10AH06 AYEWD /D/ 08LOCATION,YOKE YOKE LOCATION INDICATES THE LOCATION OF THE YOKE/S/ ON THE ITEM. SELECT REPLY CODE 10AJ91 AYEXJ /D/ 13THREAD DIAMETER,ACCOMMODATION,COIL TERMINAL COIL TERMINAL ACCOMMODATION THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COIL TERMINAL ACCOMMODATION,WHICH BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYEYD 18TYPE,ACCOMMODATION,PRIMARY TERMINAL PRIMARY TERMINAL ACCOMMODATION TYPE INDICATES THE TYPE OF PRIMARY TERMINAL ACCOMMODATION/S/ ON THE ITEM. SELECT REPLY CODE 10AA58 AYEZD /D/ 18TYPE,NUMERAL NUMERAL TYPE INDICATES THE TYPE OF NUMERAL ON THE ITEM. SELECT REPLY CODE 10AM60 AYFAG /D/ 03DESIGNATOR,LETTERING LETTERING DESIGNATOR A SIGN OF IDENTIFICATION FORMED BY A LETTER OR COMBINATION OF LETTERS TO FORM AN INSCRIPTION. FULL TEXT WRITE-IN 0 AYFBD 19AGENCY,CONTROLLING,MOUNTING STANDARD MOUNTING STANDARD CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE MOUNTING STANDARD. SELECT REPLY CODE 10AF94 AYFCG /D/ 03DESIGNATOR,MONOGRAM MONOGRAM DESIGNATOR A DEVICE,SYMBOL,OR FIGURE ADOPTED AND USED AS AN IDENTIFYING MARK. FULL TEXT WRITE-IN 0 AYFDJ /D/ 04LENGTH,FLAP,SHIRT SHIRT FLAP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SHIRT FLAP,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AYFEG /D/ 19NUMBER,STANDARD,MOUNTING MOUNTING STANDARD NUMBER THE NUMBER ASSIGNED TO THE MOUNTING STANDARD BY THE CONTROLLING AGENCY. FULL TEXT WRITE-IN 0 AYFFJ /D/ 04WIDTH,TOP,SHIRT FLAP SHIRT FLAP TOP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SHIRT FLAP TOP,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AYFGJ /D/ 04WIDTH,BOTTOM,SHIRT FLAP SHIRT FLAP BOTTOM WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SHIRT FLAP BOTTOM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AYFHA /D/ 12QUANTITY,BUTTONHOLE,SHIRT FLAP SHIRT FLAP BUTTONHOLE QUANTITY THE NUMBER OF BUTTONHOLES INCLUDED IN THE SHIRT FLAP. 1A MODE REPLY 0 AYFJJ /D/ 04LENGTH,OVERALL,TROUSERS FLAP TROUSERS FLAP OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE TROUSERS FLAP. 1D AND 1B MODE REPLY11AA05 AYFKJ /D/ 04WIDTH,CENTER,TROUSERS FLAP TROUSERS FLAP CENTER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TROUSERS FLAP CENTER,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AYFLA /D/ 12QUANTITY,BUTTONHOLE,TROUSERS FLAP TROUSERS FLAP BUTTONHOLE QUANTITY THE NUMBER OF BUTTONHOLES INCLUDED IN THE TROUSERS FLAP. 1A MODE REPLY 0 AYFMD /D/ 07LABEL,INSTRUCTION,STITCHED-IN STITCHED-IN INSTRUCTION LABEL AN INDICATION OF WHETHER OR NOT A STITCHED-IN INSTRUCTION LABEL IS INCLUDED. SELECT REPLY CODE 10AA49 AYFND 18TYPE,SUPPORT SUPPORT TYPE INDICATES THE TYPE OF SUPPORT USED WITH THE ITEM. SELECT REPLY CODE 10AM61 AYFPJ /D/ 04LENGTH FROM COIL CENTER TO OUTER END CENTER LENGTH FROM COIL CENTER TO OUTER END CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AYFQJ /D/ 04LENGTH FROM COIL CENTER TO OUTER END OUTER EDGE LENGTH FROM COIL CENTER TO OUTER END OUTER EDGE NONE. 2D AND 1B MODE REPLY21AA051AC20 AYFRJ /D/ 19DIMENSION FROM COIL AXIS TO FIRST BEND,END END DIMENSION FROM COIL AXIS TO FIRST BEND NONE. 2D AND 1B MODE REPLY21AA051AC20 AYFSJ /D/ 19DIMENSION FROM FIRST BEND TO SECOND BEND OR END,END END DIMENSION FROM FIRST BEND TO SECOND BEND OR END NONE. 2D AND 1B MODE REPLY21AA051AC20 AYFTJ /D/ 19DIMENSION FROM SECOND BEND TO THIRD BEND OR END,END END DIMENSION FROM SECOND BEND TO THIRD BEND OR END NONE. 2D AND 1B MODE REPLY21AA051AC20 AYFWJ /D/ 19DIMENSION FROM THIRD BEND TO END,END END DIMENSION FROM THIRD BEND TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AYFXJ /D/ 19DIMENSION,OFFSET OFFSET DIMENSION NONE. 2D AND 1B MODE REPLY21AA051AC20 AYFYJ /D/ 19DIMENSION,LEG,HOOK HOOK LEG DIMENSION NONE. 2D AND 1B MODE REPLY21AA051AC20 AYFZD 18TYPE,MIXTURE,INCENDIARY INCENDIARY MIXTURE TYPE INDICATES THE TYPE OF INCENDIARY MIXTURE PROVIDED. SELECT REPLY CODE 10AF45 AYGAL 16STYLE,ELECTRODE ELECTRODE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ELECTRODE. 1L MODE REPLY 0 AYGBH /D/ 13THREAD SIZE AND SERIES/TYPE DESIGNATOR AND LOCATION THREAD SIZE AND SERIES/TYPE DESIGNATOR AND LOCATION DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE,AND THE LOCATION. 2D MODE REPLY 23AM593AJ91 AYGCD 09MATERIAL,CHARGE,IGNITION IGNITION CHARGE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE IGNITION CHARGE IS COMPOSED. SELECT REPLY CODE 10AF45 AYGDD 09MATERIAL,CHARGE,BURNING BURNING CHARGE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BURNING CHARGE IS COMPOSED. SELECT REPLY CODE 10AF45 AYGEJ 10WEIGHT,CHARGE,BURNING BURNING CHARGE WEIGHT THE WEIGHT OF THE BURNING CHARGE. 1D AND 1B MODE REPLY12AB16 AYGFJ 10PRESSURE RATING,EFFECTIVE,MEAN MEAN EFFECTIVE PRESSURE RATING THE AVERAGE EFFECTIVE PRESSURE RATING FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AB181AC20 AYGGD 09MATERIAL,ELEMENT,DELAY DELAY ELEMENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE DELAY ELEMENT IS COMPOSED. SELECT REPLY CODE 10AF45 AYGHJ 04DIAMETER,MAJOR,SEAT SEAT MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AYGJJ 04HEIGHT ABOVE MOUNTING SURFACE HEIGHT ABOVE MOUNTING SURFACE NONE. 2D AND 1B MODE REPLY21AA051AC20 AYGKJ 04DISTANCE,TOP TO TERMINAL CONTACT TOP TO TERMINAL CONTACT DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AYGLJ 04DISTANCE,TOP TO SHIELD THREAD TOP TO SHIELD THREAD DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AYGMJ 04THREAD LENGTH,SHIELD SHIELD THREAD LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AYGNJ 04DIAMETER,INSIDE,BARREL BARREL INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AYGPJ 04DIAMETER,INSIDE,TERMINAL SLEEVE TERMINAL SLEEVE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AYGQJ 04HEIGHT,NOMINAL,BODY BODY NOMINAL HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BODY,IN DISTINCTION FROM DEPTH,EXCLUSIVE OF ANY PROTRUSIONS. 1D AND 1B MODE REPLY11AA05 AYGRJ 04WIDTH,NOMINAL,BODY BODY NOMINAL WIDTH A NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BODY,IN DISTINCTION FROM THICKNESS,EXCLUSIVE OF ANY PROTRUSIONS. 1D AND 1B MODE REPLY11AA05 AYGSD 08LOCATION,TAB TAB LOCATION INDICATES THE LOCATION OF THE TAB ON THE ITEM. SELECT REPLY CODE 10AJ91 AYGTD 18TYPE,TAB TAB TYPE INDICATES THE TYPE OF TAB PROVIDED. SELECT REPLY CODE 10AM35 AYGWH 03DESIGNATION AND POSITION,CUT,TAB TAB CUT DESIGNATION AND POSITION THE SPECIFIED TAB CUT BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND ITS POSITION ON THE ITEM. 2D MODE REPLY 22AL183AJ91 AYGXA 12QUANTITY,SIDE,RULED RULED SIDE QUANTITY THE NUMBER OF RULED SIDES PROVIDED. 1A MODE REPLY 0 AYGYJ 10WATTAGE RATING,AC AC WATTAGE RATING THE ALTERNATING CURRENT FOR WHICH THE ITEM IS RATED,EXPRESSED IN WATTS. 1D AND 1B MODE REPLY11AC33 AYGZD /D/ 08LOCATION,CUT,DIAGONAL CORNER DIAGONAL CORNER CUT LOCATION INDICATES THE DIAGONALLY CUT CORNER LOCATION ON THE ITEM. SELECT REPLY CODE 10AJ91 AYHAJ 10WATTAGE RATING,DC DC WATTAGE RATING THE DIRECT CURRENT FOR WHICH THE ITEM IS RATED,EXPRESSED IN WATTS. 1D AND 1B MODE REPLY11AC33 AYHBB 10VOLTAGE IN VOLTS,LINE TO LINE LINE TO LINE VOLTAGE IN VOLTS THE TOTAL ELECTRICAL LINE TO LINE VOLTAGE FOR WHICH THE ITEM IS RATED,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AYHCB 10VOLTAGE IN VOLTS,LINE TO NEUTRAL LINE TO NEUTRAL VOLTAGE IN VOLTS THE TOTAL ELECTRICAL LINE TO NEUTRAL VOLTAGE FOR WHICH THE ITEM IS RATED,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AYHDB 10FACTOR IN PERCENT,POWER POWER FACTOR IN PERCENT THE RATIO BETWEEN ACTUAL RATED POWER,AND POWER REQUIRED BY A SPECIFIED LOAD APPLIED TO THE ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 AYHED 18TYPE,EXCITOR EXCITOR TYPE INDICATES THE TYPE OF EXCITOR PROVIDED. SELECT REPLY CODE 10AF99 AYHFD /D/ 07EXCITOR EXCITOR AN INDICATION OF WHETHER OR NOT AN EXCITOR IS INCLUDED. SELECT REPLY CODE 10AA49 AYHGJ 04LENGTH,OVERALL,BOARD BOARD OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BOARD. 2D AND 1B MODE REPLY21AA051AC20 AYHHJ 04WIDTH,OVERALL,BOARD BOARD OVERALL WIDTH THE OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BOARD,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AYHJD /D/ 07FEATURE,STACKING STACKING FEATURE AN INDICATION OF WHETHER OR NOT A STACKING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AYHKD /D/ 07AGENT,DESICCANT DESICCANT AGENT AN INDICATION OF WHETHER OR NOT A DESICCANT AGENT TO ABSORB OR DISPEL MOISTURE IS INCLUDED. SELECT REPLY CODE 10AA49 AYHLG /D/ 04SIZE,DISCONNECT,QUICK,DISCHARGE CONNECTION DISCHARGE CONNECTION QUICK DISCONNECT SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSION(S) OF THE DISCHARGE CONNECTION QUICK DISCONNECT. FULL TEXT WRITE-IN 0 AYHMD /D/ 07FEATURE,PROOF,EXPLOSION EXPLOSION PROOF FEATURE AN INDICATION OF WHETHER OR NOT AN EXPLOSION PROOF FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AYHNA 19CODE,MANUFACTURER,ENGINE ENGINE MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE ENGINE. 1A MODE REPLY 0 AYHPD 18TYPE,FLANGE,DISCHARGE CONNECTION DISCHARGE CONNECTION FLANGE TYPE INDICATES THE TYPE OF DISCHARGE CONNECTION FLANGE PROVIDED. SELECT REPLY CODE 10AA78 AYHQG 19NUMBER,IDENTIFYING,ENGINE MANUFACTURER ENGINE MANUFACTURER IDENTIFYING NUMBER THE NUMBER USED BY THE MANUFACTURER FOR IDENTIFYING THE ENGINE. FULL TEXT WRITE-IN 0 AYHRD 18TYPE,HOSE HOSE TYPE INDICATES THE TYPE OF HOSE PROVIDED. SELECT REPLY CODE 10AJ58 AYHSA 12QUANTITY,SECTION,HOSE HOSE SECTION QUANTITY THE NUMBER OF HOSE SECTIONS PROVIDED. 1A MODE REPLY 0 AYHTJ 04LENGTH,HOSE HOSE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE HOSE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AYHWJ 04DIAMETER,INSIDE,HOSE HOSE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOSE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYHXA 12QUANTITY,REEL,HOSE HOSE REEL QUANTITY THE NUMBER OF HOSE REELS PROVIDED. 1A MODE REPLY 0 AYHYG /D/ 04SIZE ACCOMMODATED,HOSE HOSE SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSION/S/ OF THE HOSE THE ITEM IS DESIGNED TO ACCOMMODATE. FULL TEXT WRITE-IN 0 AYHZA 12QUANTITY,RACK,HOSE HOSE RACK QUANTITY THE NUMBER OF HOSE RACKS PROVIDED. 1A MODE REPLY 0 AYJAD /D/ 07CABLE,GROUND GROUND CABLE AN INDICATION OF WHETHER OR NOT A GROUND CABLE IS INCLUDED. SELECT REPLY CODE 10AA49 AYJBD /D/ 07REEL,CABLE CABLE REEL AN INDICATION OF WHETHER OR NOT A CABLE REEL IS INCLUDED. SELECT REPLY CODE 10AA49 AYJCD /D/ 18TYPE,REMOVER,WATER WATER REMOVER TYPE INDICATES THE TYPE OF WATER REMOVER PROVIDED. SELECT REPLY CODE 10AE98 AYJDJ 10SPACE,WORKING,RIGHT OF NEEDLE RIGHT OF NEEDLE WORKING SPACE A MEASUREMENT OF THE AMOUNT OF WORKING SPACE AVAILABLE TO THE RIGHT OF THE NEEDLE. 2D AND 1B MODE REPLY21AA051AC20 AYJED /D/ 07ASSEMBLY,MANIFOLD,DRUM EMPTYING DRUM EMPTYING MANIFOLD ASSEMBLY AN INDICATION OF WHETHER OR NOT A DRUM EMPTYING MANIFOLD ASSEMBLY IS INCLUDED. SELECT REPLY CODE 10AA49 AYJFA 12QUANTITY ACCOMMODATED,DRUM DRUM QUANTITY ACCOMMODATED THE NUMBER OF DRUMS THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 AYJGD /D/ 07LINK,TWIST TWIST LINK AN INDICATION OF WHETHER OR NOT A TWIST LINK IS INCLUDED. SELECT REPLY CODE 10AA49 AYJHJ 04LENGTH FROM TWIST LENGTH FROM TWIST A MEASUREMENT OF THE LENGTH FROM THE TWIST,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AYJJD 18TYPE,DRIVE,PUMP PUMP DRIVE TYPE INDICATES THE TYPE OF DRIVE PROVIDED FOR THE PUMP. SELECT REPLY CODE 10AC58 AYJKD /D/ 07RESERVOIR,FLUID,HYDRAULIC HYDRAULIC FLUID RESERVOIR AN INDICATION OF WHETHER OR NOT A HYDRAULIC FLUID RESERVOIR IS INCLUDED. SELECT REPLY CODE 10AA49 AYJLJ /D/ 10CAPACITY,RESERVOIR RESERVOIR CAPACITY THE AMOUNT OF FLUID THE RESERVOIR IS DESIGNED TO HOLD. PLEASE USE MRC CMRG IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1B MODE REPLY11AB10 AYJMD /D/ 07ACCUMULATOR ACCUMULATOR AN INDICATION OF WHETHER OR NOT AN ACCUMULATOR IS INCLUDED. SELECT REPLY CODE 10AA49 AYJND 18TYPE,ACCUMULATOR ACCUMULATOR TYPE INDICATES THE TYPE OF ACCUMULATOR PROVIDED. SELECT REPLY CODE 10AG85 AYJPD /D/ 07FILTER,FLUID FLUID FILTER AN INDICATION OF WHETHER OR NOT A FLUID FILTER(S) IS INCLUDED. SELECT REPLY CODE 10AA49 AYJQD 18TYPE,FILTER,FLUID FLUID FILTER TYPE INDICATES THE TYPE OF FLUID FILTER PROVIDED. SELECT REPLY CODE 10AC58 AYJRD 18TYPE,HOLDER,HOSE HOSE HOLDER TYPE INDICATES THE TYPE OF HOSE HOLDER/S/ PROVIDED. SELECT REPLY CODE 10AC58 AYJSD /D/ 07SET,HOSE,MANIFOLDING MANIFOLDING HOSE SET AN INDICATION OF WHETHER OR NOT A MANIFOLDING HOSE SET IS INCLUDED. SELECT REPLY CODE 10AA49 AYJTA 12QUANTITY,OUTLET OUTLET QUANTITY THE NUMBER OF OUTLETS PROVIDED. 1A MODE REPLY 0 AYJWJ /D/A18TYPE AND QUANTITY,ELEMENT,ROLLING ROLLING ELEMENT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF ROLLING ELEMENTS FOR MOVING THE UNIT. PLEASE USE MRC CYMB IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1A MODE REPLY12AA78 AYJXD 19DEVICE,PULLING PULLING DEVICE AN INDICATION OF THE DEVICE PROVIDED FOR PULLING THE ITEM. SELECT REPLY CODE 10AF69 AYJYD 11METHOD,MOUNTING,PUMP HEAD BODY PUMP HEAD BODY MOUNTING METHOD THE MEANS OF ATTACHING THE PUMP HEAD BODY. SELECT REPLY CODE 10AM39 AYJZG /D/ 04SIZE FOR WHICH PUMP HEAD BODY IS DESIGNED,OPENING,BUNG BUNG OPENING SIZE FOR WHICH PUMP HEAD BODY IS DESIGNED DESIGNATES THE SIZE OF THE BUNG OPENING FOR WHICH THE PUMP HEAD BODY IS DESIGNED. FULL TEXT WRITE-IN 0 AYKAD 18TYPE,FITTING,DISCHARGE DISCHARGE FITTING TYPE INDICATES THE TYPE OF DISCHARGE FITTING PROVIDED. SELECT REPLY CODE 10AM35 AYKBJ 04LENGTH,OVERALL,HOSE HOSE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE HOSE. 2D AND 1B MODE REPLY21AA051AC20 AYKCJ 04SIZE,NOMINAL,HOSE HOSE NOMINAL SIZE DESIGNATES THE NOMINAL SIZE,SUCH AS LENGTH,WIDTH,DIAMETER,AND THE LIKE,OF THE HOSE. 1D AND 1B MODE REPLY11AA05 AYKDD 11METHOD,CONTROL,ADVANCE,SPARK SPARK ADVANCE CONTROL METHOD THE MEANS BY WHICH THE SPARK ADVANCE IS CONTROLLED. SELECT REPLY CODE 10AC58 AYKEJ /D/ 10WEIGHT PER DOZEN,MINIMUM MINIMUM WEIGHT PER DOZEN THE MINIMUM WEIGHT,WHEN THE ITEM IS NORMALLY SUPPLIED IN LOTS OF A DOZEN EACH. 1D AND 1B MODE REPLY12AG67 AYKFB 10ADVANCE DEG,MAXIMUM MAXIMUM ADVANCE DEG THE MAXIMUM NUMBER OF DEGREES THE ITEM IS ADVANCED. 1B MODE REPLY 0 AYKGD 18TYPE,LANTERN LANTERN TYPE INDICATES THE TYPE OF LANTERN AS DISTINGUISHED BY ITS PARTICULAR DESIGN. SELECT REPLY CODE 10AD48 AYKHD 18TYPE,ELEMENT,ROTATING ROTATION ELEMENT TYPE INDICATES THE TYPE OF ROTATING ELEMENT USED WITH THE ITEM. SELECT REPLY CODE 10AJ21 AYKJJ 04WIDTH,WICK WICK WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE WICK,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AYKKA 12QUANTITY,MANTLE MANTLE QUANTITY THE NUMBER OF MANTLES THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 AYKLD 01COLOR,GLOBE GLOBE COLOR THE HUE OR TINT OF THE GLOBE. SELECT REPLY CODE 10AD06 AYKMD 19TRANSPARENCY,GLOBE GLOBE TRANSPARENCY THE ABILITY OF THE GLOBE TO TRANSMIT LIGHT AND ALLOW VISUAL PERCEPTION. SELECT REPLY CODE 10AF93 AYKNA 12QUANTITY,SET,CONTACT CONTACT SET QUANTITY THE NUMBER OF CONTACT SETS INCORPORATED IN THE UNIT. 1A MODE REPLY 0 AYKPJ /D/ 04DISTANCE FROM GLOBE TOP TO FROSTED AREA DISTANCE FROM GLOBE TOP TO FROSTED AREA THE DISTANCE FROM THE TOP OF THE GLOBE TO THE AREA WHERE FROSTING BEGINS. 2D AND 1B MODE REPLY21AA051AC20 AYKQD /D/ 07ACCOMMODATION,DRIVE,TACHOMETER TACHOMETER DRIVE ACCOMMODATION AN INDICATION OF WHETHER OR NOT ACCOMMODATION FOR A TACHOMETER DRIVE IS INCLUDED. SELECT REPLY CODE 10AA49 AYKRJ /D/ 04WIDTH,HEM HEM WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE HEM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AYKSD 18TYPE,BOTTOM,LEG LEG BOTTOM TYPE INDICATES THE TYPE OF LEG BOTTOM INCLUDED ON THE ITEM. SELECT REPLY CODE 10AF85 AYKTG /D/ 04DISTANCE FROSTED AREA EXTENDS DISTANCE FROSTED AREA EXTENDS THE EXTENT OF THE FROSTED AREA ON THE ITEM. FULL TEXT WRITE-IN 0 AYKWJ 04DIAMETER,RIM,BOTTOM OUTSIDE BOTTOM OUTSIDE RIM DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOTTOM OUTSIDE RIM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYKXJ 04DIAMETER,RIM,TOP OUTSIDE TOP OUTSIDE RIM DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TOP OUTSIDE RIM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYKYJ 10CAPACITY,FOUNT FOUNT CAPACITY THE AMOUNT OF LIQUID THE FOUNT WILL HOLD. 1D AND 1B MODE REPLY12AG67 AYKZD 18TYPE,INCLOSURE,SECTION,ELECTRICAL ELECTRICAL SECTION INCLOSURE TYPE INDICATES THE TYPE OF INCLOSURE PROVIDED TO COAT,COVER,PROTECT,OR ENCASE THE ELECTRICAL SECTION OF THE ITEM. SELECT REPLY CODE 10AJ95 AYLAJ /D/ 04DISTANCE FROM TOP SHOULDER TO TOP END DISTANCE FROM TOP SHOULDER TO TOP END THE DISTANCE FROM THE TOP SHOULDER TO THE TOP END OF AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 AYLCB 10TIME PER FILL IN HOURS,BURNING BURNING TIME PER FILL IN HOURS THE LENGTH OF TIME THE ITEM WILL BURN BEFORE REFILLING,EXPRESSED IN HOURS. 1B MODE REPLY 0 AYLDJ /D/ 04DISTANCE FROM BOTTOM SHOULDER TO BOTTOM END DISTANCE FROM BOTTOM SHOULDER TO BOTTOM END THE DISTANCE FROM THE BOTTOM SHOULDER TO THE BOTTOM END OF AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 AYLED 18TYPE,INCLOSURE,MECHANICAL SECTION MECHANICAL SECTION INCLOSURE TYPE INDICATES THE TYPE OF INCLOSURE PROVIDED TO COAT,COVER,PROTECT,OR ENCASE THE MECHANICAL SECTION OF THE ITEM. SELECT REPLY CODE 10AJ95 AYLFB 10RPM AT MAXIMUM ADVANCE RPM AT MAXIMUM ADVANCE THE REVOLUTIONS PER MINUTE OF THE ITEM AT MAXIMUM ADVANCE. 1B MODE REPLY 0 AYLGG 19AGENCY,CONTROLLING,SIGNAL CABLE SIGNAL CABLE CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION THAT CONTROLS THE MANUFACTURE OF THE SIGNAL CABLE. FULL TEXT WRITE-IN 0 AYLHJ 04DIAMETER,BLOCK BLOCK DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BLOCK,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYLJJ 04DIAMETER,OUTSIDE,BRAKING AREA BRAKING AREA OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BRAKING AREA,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYLKJ 04DIAMETER,OUTSIDE,ROTATING DISK ROTATING DISK OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A ROTATING DISK,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYLLJ 04DIAMETER,SHOE SHOE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHOE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYLMJ 04WIDTH,SURFACE,LINING CONTACT LINING CONTACT SURFACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A LINING CONTACT SURFACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AYLNJ 04WIDTH,BLOCK BLOCK WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BLOCK,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AYLPJ 04WIDTH,SHOE SHOE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A SHOE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AYLQJ 04DIAMETER,INSIDE,BRAKING AREA BRAKING AREA INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO INSIDE SURFACES OF A CIRCULAR BRAKING AREA,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYLRJ 04THICKNESS,DISK,ROTATING ROTATING DISK THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE ROTATING DISK,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AYLSJ 04THICKNESS,DISK,STATIONARY STATIONARY DISK THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE STATIONARY DISK,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AYLTA 12QUANTITY,DISK,ROTATING ROTATING DISK QUANTITY THE NUMBER OF ROTATING DISKS. 1A MODE REPLY 0 AYLWA 12QUANTITY,CYLINDER,HYDRAULIC HYDRAULIC CYLINDER QUANTITY THE NUMBER OF HYDRAULIC CYLINDERS. 1A MODE REPLY 0 AYLXJ 04DIAMETER,CYLINDER,HYDRAULIC HYDRAULIC CYLINDER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HYDRAULIC CYLINDER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYLYD 07ADJUSTABILITY,PIPE,INTAKE INTAKE PIPE ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE INTAKE PIPE IS ADJUSTABLE. SELECT REPLY CODE 10AB00 AYLZJ T10RANGE,ADJUSTMENT ADJUSTMENT RANGE THE MINIMUM AND MAXIMUM LIMITS TO WHICH THE ITEM MAY BE ADJUSTED. 1D AND 1F MODE REPLY11AA05 AYMAD /D/ 18TYPE,DRAIN,FLUID RETURN FLUID RETURN DRAIN TYPE INDICATES THE TYPE OF FLUID RETURN DRAIN PROVIDED. SELECT REPLY CODE 10AK54 AYMBG 10DELIVERY RATING DELIVERY RATING AN INDICATION OF THE RATED DELIVERY OF THE ITEM. FULL TEXT WRITE-IN 0 AYMCG /D/ 03DESIGNATION,BOOK,INSTRUCTION INSTRUCTION BOOK DESIGNATION THE DESIGNATION IDENTIFYING THE INSTRUCTION BOOK. FULL TEXT WRITE-IN 0 AYMDG /D/ 18TYPE FOR WHICH DESIGNED,DECK DECK TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF DECK FOR WHICH DESIGNED. FULL TEXT WRITE-IN 0 AYMEA 12QUANTITY,CHANNEL,AMPLIFIER AMPLIFIER CHANNEL QUANTITY THE NUMBER OF AMPLIFIER CHANNELS PROVIDED. 1A MODE REPLY 0 AYMFG 19NAME,AMPLIFIER AMPLIFIER NAME THE NOMENCLATURE BY WHICH THE AMPLIFIER IS IDENTIFIED. FULL TEXT WRITE-IN 0 AYMGJ 10OUTPUT RATING,POWER,AMPLIFIER AMPLIFIER POWER OUTPUT RATING THE RATED POWER OUTPUT FOR WHICH THE AMPLIFIER IS DESIGNED. 2D AND 1B MODE REPLY21AC331AC20 AYMHJ 10OUTPUT RATING,VOLTAGE,AMPLIFIER AMPLIFIER VOLTAGE OUTPUT RATING THE RATED VOLTAGE OUTPUT FOR WHICH THE AMPLIFIER IS DESIGNED. 2D AND 1B MODE REPLY21AB631AC20 AYMJJ 10IMPEDANCE RATING,OUTPUT,AMPLIFIER AMPLIFIER OUTPUT IMPEDANCE RATING THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) PRESENTED BY THE AMPLIFIER TO AN ALTERNATING CURRENT LOAD. 2D AND 1B MODE REPLY22AE751AC20 AYMKD 19CHARACTERISTIC,INPUT,AMPLIFIER INFORMATION AMPLIFIER INFORMATION INPUT CHARACTERISTIC AN INDICATION OF THE AMPLIFIER INFORMATION INPUT CHARACTERISTIC/S/. SELECT REPLY CODE 10AJ41 AYMLG /D/ 18TYPE,INPUT,COMPUTER INTELLIGENCE COMPUTER INTELLIGENCE INPUT TYPE INDICATES THE TYPE OF INTELLIGENCE INPUT TO A COMPUTER. FULL TEXT WRITE-IN 0 AYMMG /D/ 18TYPE,OUTPUT,COMPUTER INTELLIGENCE COMPUTER INTELLIGENCE OUTPUT TYPE INDICATES THE TYPE OF INTELLIGENCE OUTPUT FROM A COMPUTER. FULL TEXT WRITE-IN 0 AYMNJ 10GAGE,TRACK TRACK GAGE THE WIDTH BETWEEN THE RAIL HEADS. 1D AND 1B MODE REPLY11AA05 AYMPJ 10WEIGHT,GROSS GROSS WEIGHT THE WEIGHT OF THE ITEM FULLY EQUIPPED. 1D AND 1B MODE REPLY12AG67 AYMQA 19ARRANGEMENT,WHEEL,WHYTE SYSTEM WHYTE SYSTEM WHEEL ARRANGEMENT THE WHEEL ARRANGEMENT AS SPECIFIED BY THE WHYTE SYSTEM. 1A MODE REPLY 0 AYMRD 18TYPE,WHEEL WHEEL TYPE INDICATES THE TYPE OF WHEEL/S/ PROVIDED ON THE ITEM. SELECT REPLY CODE 10AH67 AYMSJ 04DIAMETER,WHEEL WHEEL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A WHEEL,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AYMTJ /D/ 18TYPE AND SPACING,WHEELBASE WHEELBASE TYPE AND SPACING INDICATES THE TYPE AND SPACING BETWEEN THE LEADING AND TRAILING AXLES OF THE WHEELBASE. 2D AND 1B MODE REPLY21AA052AA78 AYMWJ 04DISTANCE BETWEEN WHEELBASES,TOTAL TOTAL DISTANCE BETWEEN WHEELBASES THE TOTAL DISTANCE BETWEEN THE LEADING AND TRAILING AXLES OF THE WHEELBASE/S/ ON THE ITEM. 1D AND 1B MODE REPLY11AA05 AYMXJ 04RADIUS,MINIMUM,NEGOTIABLE TRACK CURVE NEGOTIABLE TRACK CURVE MINIMUM RADIUS THE MINIMUM TRACK CURVATURE RADIUS WHICH CAN BE NEGOTIATED BY THE ITEM. 1D AND 1B MODE REPLY11AA05 AYMYA 12QUANTITY,ENGINE ENGINE QUANTITY THE NUMBER OF ENGINES PROVIDED. 1A MODE REPLY 0 AYMZG /D/ 10HORSEPOWER/RPM RATING,ENGINE,MAXIMUM MAXIMUM ENGINE HORSEPOWER/RPM RATING THE MAXIMUM ENGINE HORSEPOWER GENERATED AT RECOMMENDED REVOLUTIONS PER MINUTE. FULL TEXT WRITE-IN 0 AYNAJ 10FREQUENCY RATING,INCOMING,CONVERTER CONVERTER INCOMING FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE CONVERTER INCOME IS RATED. 2D AND 1B MODE REPLY21AC321AC20 AYNBD /D/ 07FITTING FITTING AN INDICATION OF WHETHER OR NOT A FITTING(S) IS INCLUDED. SELECT REPLY CODE 10AA49 AYNCA /D/ 12QUANTITY ACCOMMODATED,UNIT,CRYSTAL CRYSTAL UNIT QUANTITY ACCOMMODATED THE NUMBER OF CRYSTAL UNITS THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 AYNDD /D/ 07UNIT,CRYSTAL,REPLACEABLE REPLACEABLE CRYSTAL UNIT AN INDICATION OF WHETHER OR NOT A REPLACEABLE CRYSTAL UNIT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 AYNEA 03DESIGNATOR,HOLDER,CRYSTAL CRYSTAL HOLDER DESIGNATOR THE DESIGNATION ASSIGNED TO THE CRYSTAL HOLDER(S) FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 AYNFJ 10TEMP RATING,CAVITY,OVEN,MAINTAINED MAINTAINED OVEN CAVITY TEMP RATING THE VALUE WHICH EXPRESSES THE DEGREE OF CONTROLLED TEMPERATURE MAINTAINED IN THE OVEN CAVITY. 1D AND 1B MODE REPLY11AB36 AYNGJ T10TOLERANCE RATING,TEMP,MAINTAINED MAINTAINED TEMP TOLERANCE RATING THE LIMITS OF PERMISSIBLE VARIATION OF AN ITEM FROM ITS CONTROLLED TEMPERATURE RATING. 1D AND 1F MODE REPLY11AB36 AYNHJ T10RANGE,TEMP,AMBIENT,OPERATING OPERATING AMBIENT TEMP RANGE THE AMBIENT TEMPERATURE RANGE AT WHICH THE ITEM IS DESIGNED TO OPERATE. 1D AND 1F MODE REPLY11AB36 AYNJJ 10VOLTAGE RATING IN VOLTS AND TYPE,OPERATING,HEATER ELEMENT HEATER ELEMENT OPERATING VOLTAGE RATING IN VOLTS AND TYPE INDICATES THE OPERATING VOLTAGE TYPE THAT IS APPLIED TO THE HEATER ELEMENT,EXPRESSED IN VOLTS. 2D AND 1B MODE REPLY21AB621AC20 AYNKJ /D/A03DESIGNATION,TERMINAL TERMINAL DESIGNATION A DESIGNATION ASSIGNED TO THE TERMINAL FOR THE PURPOSE OF IDENTIFICATION. 1D AND 1A MODE REPLY12AE98 AYNLB 10DISSIPATING RATING IN WATTS,POWER,OPERATING OPERATING POWER DISSIPATING RATING IN WATTS THE MAXIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED FOR PROPER OPERATION OF AN ITEM,MEASURED IN WATTS. 1B MODE REPLY 0 AYNMB 10TIME IN MINUTES,WARM UP,MAXIMUM MAXIMUM WARM UP TIME IN MINUTES THE MAXIMUM TIME REQUIRED TO REACH THE CONTROLLED TEMPERATURE,EXPRESSED IN MINUTES. 1B MODE REPLY 0 AYNPJ 10FREQUENCY RATING,OUTPUT,CONVERTER CONVERTER OUTPUT FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE CONVERTER OUTPUT IS RATED. 2D AND 1B MODE REPLY21AC321AC20 AYNQJ 10FREQUENCY RATING,INPUT,MULTIPLIER MULTIPLIER INPUT FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE MULTIPLIER INPUT IS RATED. 2D AND 1B MODE REPLY21AC321AC20 AYNRJ 10FREQUENCY RATING,OUTPUT,MULTIPLIER MULTIPLIER OUTPUT FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE MULTIPLIER OUTPUT IS RATED. 2D AND 1B MODE REPLY21AC321AC20 AYNSJ 10AREA,SURFACE,FRICTION,LINING LINING FRICTION SURFACE AREA THE AMOUNT OF SURFACE AREA COVERED BY THE FRICTION LINING OF THE ITEM. 2D AND 1B MODE REPLY21AC511AC20 AYNTA 12QUANTITY,SHOE SHOE QUANTITY THE NUMBER OF SHOES. 1A MODE REPLY 0 AYNWA 12QUANTITY,ROTOR ROTOR QUANTITY THE NUMBER OF ROTORS. 1A MODE REPLY 0 AYNXJ 10FREQUENCY,RECEIVING,ELECTROMAGNETIC WAVE ELECTROMAGNETIC WAVE RECEIVING FREQUENCY THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,OF THE ELECTROMAGNETIC WAVE RECEIVED. 2D AND 1B MODE REPLY21AC321AC20 AYNYD 08LOCATION,INSTALLATION INSTALLATION LOCATION INDICATES THE LOCATION FOR WHICH THE ITEM IS DESIGNED TO BE INSTALLED. SELECT REPLY CODE 10AJ91 AYNZJ 10FREQUENCY,TRANSMITTING,ELECTROMAGNETIC WAVE ELECTROMAGNETIC WAVE TRANSMITTING FREQUENCY THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,OF THE ELECTROMAGNETIC WAVE TRANSMITTED. 2D AND 1B MODE REPLY21AC321AC20 AYPAB 10OUTPUT IN WATTS,POWER,TRANSMITTING,ELECTROMAGNETIC WAVE ELECTROMAGNETIC WAVE TRANSMITTING POWER OUTPUT IN WATTS THE RATED POWER THAT AN ELECTROMAGNETIC WAVE CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS. 1B MODE REPLY 0 AYPBJ 10FREQUENCY,RECEIVING,UNDERWATER SOUND WAVE UNDERWATER SOUND WAVE RECEIVING FREQUENCY THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,OF THE UNDERWATER SOUND WAVE RECEIVED. 2D AND 1B MODE REPLY21AC321AC20 AYPCD /D/ 07STARTER STARTER AN INDICATION OF WHETHER OR NOT A STARTER IS INCLUDED. SELECT REPLY CODE 10AA49 AYPDD 18TYPE,EMISSION,SONAR SONAR EMISSION TYPE A CLASSIFICATION OF SONAR FREQUENCY EMISSIONS IN WHICH THE TYPE OF MODULATION,TRANSMISSION,AND/OR SUPPLEMENTARY CHARACTERISTICS ARE REPRESENTED BY SYMBOLS. SELECT REPLY CODE 10AJ76 AYPEG 04SIZE FOR WHICH DESIGNED,WHEEL WHEEL SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE WHEEL FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 AYPFJ 10FREQUENCY,TRANSMITTING,UNDERWATER SOUND WAVE UNDERWATER SOUND WAVE TRANSMITTING FREQUENCY THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,OF THE UNDERWATER SOUND WAVE TRANSMITTED. 2D AND 1B MODE REPLY21AC321AC20 AYPGB 10OUTPUT IN WATTS,POWER,TRANSMITTING,UNDERWATER SOUND WAVE UNDERWATER SOUND WAVE TRANSMITTING POWER OUTPUT IN WATTS THE RATED POWER THAT THE UNDERWATER SOUND WAVE CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS. 1B MODE REPLY 0 AYPHJ 04WIDTH,PULSE PULSE WIDTH THE TIME INTERVAL BETWEEN THE 50 PERCENT AMPLITUDE POINTS IN RELATIONSHIP TO THE PEAK PULSE AMPLITUDE. 1D AND 1B MODE REPLY12AB49 AYPJA 12QUANTITY,LINING LINING QUANTITY THE NUMBER OF LININGS PROVIDED. 1A MODE REPLY 0 AYPKJ 04DIAMETER FOR WHICH DESIGNED,DRUM DRUM DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DRUM FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYPLJ 04WIDTH,LINING LINING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE LINING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AYPMJ 04THICKNESS,LINING LINING THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE LINING,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AYPNJ 04LENGTH,LINING LINING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE LINING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AYPPD 18TYPE,CONTROL,FREQUENCY FREQUENCY CONTROL TYPE INDICATES THE TYPE OF FREQUENCY CONTROL PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AL37 AYPQD 08LOCATION,SURFACE,BRAKING BRAKING SURFACE LOCATION INDICATES THE BRAKING SURFACE LOCATION ON THE ITEM. SELECT REPLY CODE 10AJ91 AYPRD 02DESIGN,DOME DOME DESIGN THE DESIGN OF THE DOME. SELECT REPLY CODE 10AJ17 AYPSD /D/ 09MATERIAL,WALL WALL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WALL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH USE IF ISAC TABLE 0143 IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AYPTD /D/ 09MATERIAL,WINDOW WINDOW MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WINDOW IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AYPWJ 04THICKNESS,WINDOW WINDOW THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE WINDOW,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AYPXD /D/ 07BAFFLE BAFFLE AN INDICATION OF WHETHER OR NOT A BAFFLE IS PROVIDED. SELECT REPLY CODE 10AB22 AYPYD 19USAGE,VOLTAGE,AC AC VOLTAGE USAGE THE MANNER IN WHICH THE ALTERNATING CURRENT VOLTAGE IS USED BY THE ITEM. SELECT REPLY CODE 10AM62 AYPZD 19USAGE,VOLTAGE,DC DC VOLTAGE USAGE THE MANNER IN WHICH THE DIRECT CURRENT VOLTAGE IS USED BY THE ITEM. SELECT REPLY CODE 10AM62 AYQAJ 04DIAMETER,SURFACE,BRAKING BRAKING SURFACE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BRAKING SURFACE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYQBJ 04WIDTH,SURFACE,BRAKING BRAKING SURFACE WIDTH THE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BRAKING SURFACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AYQCG /D/ 04SIZE,HOLE HOLE SIZE DESIGNATES THE SIZE OF THE HOLE(S) OF THE ITEM. FULL TEXT WRITE-IN 0 AYQDJ 10SPEED IN RPM,RATED RATED SPEED IN RPM THE RATED SPEED F0R WHICH THE ITEM HAS BEEN TESTED TO PERFORM,EXPRESSED IN REVOLUTIONS PER MINUTE. 1D AND 1B MODE REPLY11AC20 AYQEG 04SPACING,HOLE HOLE SPACING THE SPACING BETWEEN THE HOLES. FULL TEXT WRITE-IN 0 AYQFD /D/ 07FIN,COOLING COOLING FIN AN INDICATION OF WHETHER OR NOT A COOLING FIN/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 AYQGD /D/ 09MATERIAL,BRUSH BRUSH MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BRUSH IS FABRICATED. SELECT REPLY CODE 10AD09 AYQHD /D/ 07HOLE,ADJUSTMENT ADJUSTMENT HOLE AN INDICATION OF WHETHER OR NOT AN ADJUSTMENT HOLE IS INCLUDED. SELECT REPLY CODE 10AA49 AYQJD /D/ 07HOLE,INSPECTION INSPECTION HOLE AN INDICATION OF WHETHER OR NOT AN INSPECTION HOLE IS INCLUDED. SELECT REPLY CODE 10AA49 AYQKD /D/ 07HOLE,DRAIN,OIL OIL DRAIN HOLE AN INDICATION OF WHETHER OR NOT AN OIL DRAIN HOLE IS INCLUDED. SELECT REPLY CODE 10AA49 AYQLD /D/ 07PAD,BALANCING BALANCING PAD AN INDICATION OF WHETHER OR NOT A BALANCING PAD(S) IS INCLUDED. SELECT REPLY CODE 10AA49 AYQMD 08LOCATION,MOUNTING MOUNTING LOCATION INDICATES THE MOUNTING LOCATION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AJ91 AYQNJ /D/ 04HEIGHT,OVERALL,BOARD BOARD OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AYQPJ /D/ 04HEIGHT EXCLUDING TERMINALS,BOARD BOARD HEIGHT EXCLUDING TERMINALS NONE. 2D AND 1B MODE REPLY21AA051AC20 AYQQJ /D/ 04THICKNESS,BOARD BOARD THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AYQRJ 04DISTANCE BETWEEN TERMINAL ROWS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN TERMINAL ROWS THE CENTER TO CENTER DISTANCE BETWEEN THE ROWS OF TERMINALS. 2D AND 1B MODE REPLY21AA051AC20 AYQSJ 04DIAMETER,CIRCLE,TERMINAL TERMINAL CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TERMINAL CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYQTJ /D/ 04WIDTH,HOLE,MOUNTING MOUNTING HOLE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A MOUNTING HOLE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AYQWJ /D/ 04DISTANCE FROM BOTTOM EDGE OF TERMINAL BOARD TO CENTER OF MOUNTING HOLE DISTANCE FROM BOTTOM EDGE OF TERMINAL BOARD TO CENTER OF MOUNTING HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 AYQXJ /D/ 04DISTANCE FROM LEFT EDGE OF TERMINAL BOARD TO CENTER OF FIRST MOUNTING FACILITY DISTANCE FROM LEFT EDGE OF TERMINAL BOARD TO CENTER OF FIRST MOUNTING FACILITY NONE. 2D AND 1B MODE REPLY21AA051AC20 AYQYJ /D/ 04DISTANCE FROM BOTTOM EDGE OF TERMINAL BOARD TO BOTTOM OF MOUNTING FOOT DISTANCE FROM BOTTOM EDGE OF TERMINAL BOARD TO BOTTOM OF MOUNTING FOOT NONE. 2D AND 1B MODE REPLY21AA051AC20 AYQZD 11METHOD,STARTING,PRIME MOVER PRIME MOVER STARTING METHOD THE MEANS USED TO START THE PRIME MOVER. SELECT REPLY CODE 10AC58 AYRAG 19INSCRIPTION,TAB TAB INSCRIPTION ANY LETTER(S),NUMERAL(S),SYMBOL(S),OR COMBINATION THEREOF,INSCRIBED ON THE TAB. FULL TEXT WRITE-IN 0 AYRBG /D/ 19NUMBER,IDENTIFYING,TERMINAL BOARD TERMINAL BOARD IDENTIFYING NUMBER THE SPECIFICATION,STANDARD,OR MANUFACTURER IDENTIFICATION NUMBER OR SYMBOL USED TO IDENTIFY THE TERMINAL BOARD. FULL TEXT WRITE-IN 0 AYRCA /D/ 19CODE,MANUFACTURER,TERMINAL BOARD TERMINAL BOARD MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE TERMINAL BOARD. 1A MODE REPLY 0 AYRDH /D/ 14SHAPE AND LOCATION,CORNER CORNER SHAPE AND LOCATION AN INDICATION OF THE PREFORMED SHAPE OF THE CORNER/S/ AND ITS LOCATION ON THE ITEM. 2D MODE REPLY 22AE883AJ91 AYREJ 04DIAMETER,INSIDE,INTERNAL FLANGE INTERNAL FLANGE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AYRFJ 04DIAMETER,OUTSIDE,INTERNAL FLANGE INTERNAL FLANGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AYRGJ 04WIDTH,FLANGE,INTERNAL INTERNAL FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AYRHJ 04WIDTH,LIP,INTERNAL FLANGE INTERNAL FLANGE LIP WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AYRJJ 04THICKNESS,FLANGE,CENTER CENTER FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AYRKJ 04RADIUS,FLANGE,SMALLEST EXTERNAL ANCHOR SMALLEST EXTERNAL ANCHOR FLANGE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AYRLJ 04RADIUS,FLANGE,LARGEST EXTERNAL ANCHOR LARGEST EXTERNAL ANCHOR FLANGE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AYRMJ 04DISTANCE BELOW CENTERLINE DISTANCE BELOW CENTERLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 AYRNJ 04WIDTH,HOLE,POSITIONING POSITIONING HOLE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AYRPJ 04WIDTH,LUG,POSITIONING POSITIONING LUG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AYRQJ 04LENGTH,LUG,POSITIONING POSITIONING LUG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AYRRJ 04DEPTH,HOLE,POSITIONING POSITIONING HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AYRSJ 04DISTANCE FROM END DISTANCE FROM END NONE. 2D AND 1B MODE REPLY21AA051AC20 AYRTJ 04WIDTH,FLANGE,ANCHOR ANCHOR FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AYRWJ 04DISTANCE FROM HOLE CENTER TO RIGHT FACE DISTANCE FROM HOLE CENTER TO RIGHT FACE NONE. 2D AND 1B MODE REPLY21AA051AC20 AYRXJ 04WIDTH,GROOVE,ANCHOR ANCHOR GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AYRYB /D/ 04ANGLE IN DEG,POSITION POSITION ANGLE IN DEG NONE. 1B MODE REPLY 0 AYRZJ 04DIAMETER,COUNTERSINK COUNTERSINK DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COUNTERSINK,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYSAB 10VOLTAGE IN VOLTS,CRANKING CRANKING VOLTAGE IN VOLTS THE TOTAL ELECTRICAL VOLTAGE REQUIRED FOR CRANKING THE ITEM,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AYSBB 10CURRENT IN AMPS,CRANKING CRANKING CURRENT IN AMPS THE TOTAL ELECTRICAL CURRENT REQUIRED FOR CRANKING THE ITEM,EXPRESSED IN AMPERES. 1B MODE REPLY 0 AYSCA 19ARRANGEMENT,FORM,PILE-UP MAIN CONTACT PILE-UP MAIN CONTACT FORM ARRANGEMENT THE NUMBER AND COMBINATION(S) OF THE BASIC CONTACT FORMS,IN THE ORDER OF ASSEMBLAGE,WHICH MAKE UP THE SWITCHING STRUCTURE OF THE PILE-UP MAIN CONTACTS. 1A MODE REPLY 0 AYSDA 19ARRANGEMENT,FORM,AUXILIARY CONTACT,PILE-UP PILE-UP AUXILIARY CONTACT FORM ARRANGEMENT THE NUMBER AND COMBINATION(S) OF THE BASIC CONTACT FORMS,IN ORDER OF ASSEMBLAGE,WHICH MAKE UP THE SWITCHING STRUCTURE OF THE PILE-UP AUXILIARY CONTACTS. 1A MODE REPLY 0 AYSEA /D/ 19ARRANGEMENT,CONTACT,MAIN MAIN CONTACT ARRANGEMENT THE DESIGNATION THAT IDENTIFIES THE SCHEMATIC DIAGRAM OF THE CONTACT CONFIGURATION. 1A MODE REPLY 0 AYSFA /D/ 19ARRANGEMENT,CONTACT,AUXILIARY AUXILIARY CONTACT ARRANGEMENT THE DESIGNATION THAT IDENTIFIES THE SCHEMATIC DIAGRAM OF THE CONTACT CONFIGURATION. 1A MODE REPLY 0 AYSGD /D/ 18TYPE,CURRENT,MAIN CONTACT MAIN CONTACT CURRENT TYPE INDICATES THE TYPE OF CURRENT USED WITH THE CONTACT/S/. SELECT REPLY CODE 10AB62 AYSHJ 04DISTANCE FROM EDGE OF PLATE TO TONGUE DISTANCE FROM EDGE OF PLATE TO TONGUE NONE. 2D AND 1B MODE REPLY21AA051AC20 AYSJB /D/ 04ANGLE IN DEG,CHAMFER,TOP TOP CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AYSKB 04ANGLE IN DEG,CHAMFER,BOTTOM BOTTOM CHAMFER ANGLE IN DEG THE ANGLE OF THE BOTTOM CHAMFER,EXPRESSED IN DEGREES. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 AYSLJ /D/ 04LENGTH,CHAMFER,TOP TOP CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 AYSMJ 04LENGTH,CHAMFER,BOTTOM BOTTOM CHAMFER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BOTTOM CHAMFER,IN DISTINCTION FROM WIDTH. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 AYSNB /D/ 19DEG,COUNTERSINK COUNTERSINK DEG NONE. 1B MODE REPLY 0 AYSPJ 04DISTANCE FROM CENTER OF HOLE TO EDGE OF PLATE DISTANCE FROM CENTER OF HOLE TO EDGE OF PLATE NONE. 2D AND 1B MODE REPLY21AA051AC20 AYSQJ 04DIAMETER,HOLE,ANCHOR PIN ANCHOR PIN HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ANCHOR PIN HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYSRJ 04DISTANCE,CENTER TO CENTER,PIN HOLE,ANCHOR ANCHOR PIN HOLE CENTER TO CENTER DISTANCE THE DISTANCE FROM THE CENTER OF ONE ANCHOR PIN HOLE TO THE CENTER OF THE ADJACENT ANCHOR PIN HOLE. 2D AND 1B MODE REPLY21AA051AC20 AYSSD 08LOCATION,CAM CAM LOCATION INDICATES THE LOCATION OF THE CAM ON THE ITEM. SELECT REPLY CODE 10AJ91 AYSTD 19PHASE,WINDING WINDING PHASE THE NUMBER OF ALTERNATING CURRENT WINDING PHASES. SELECT REPLY CODE 10AD02 AYSWD 14SHAPE,CAM CAM SHAPE THE PHYSICAL CONFIGURATION OF THE CAM. SELECT REPLY CODE 10AD07 AYSXD /D/ 09MATERIAL,SHELL,OUTSIDE OUTSIDE SHELL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE OUTSIDE SHELL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AYSYD 05DIRECTION FOR WHICH DESIGNED,ROTATION ROTATION DIRECTION FOR WHICH DESIGNED THE DIRECTION OF ROTATION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AA38 AYSZJ 04LENGTH,OVERALL,CAM CAM OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CAM. 2D AND 1B MODE REPLY21AA051AC20 AYTAJ 04THICKNESS,CENTER CAM CAM CENTER THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE CAM,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AYTBA /D/ 12QUANTITY PER FREEZE,ICE CUBE ICE CUBE QUANTITY PER FREEZE THE NUMBER OF ICE CUBES PER FREEZE. 1A MODE REPLY 0 AYTCD 08LOCATION,HINGE HINGE LOCATION INDICATES THE LOCATION OF THE HINGE/S/ ON THE ITEM. SELECT REPLY CODE 10AJ91 AYTDJ 04THICKNESS,FLANGE,CAM RETAINING CAM RETAINING FLANGE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE CAM RETAINING FLANGE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AYTEJ T10RANGE,TEMP,OPERATING,FROZEN FOOD COMPARTMENT FROZEN FOOD COMPARTMENT OPERATING TEMP RANGE THE MINIMUM AND MAXIMUM LIMITS OF OPERATING TEMPERATURE AT WHICH THE FROZEN FOOD COMPARTMENT IS RATED. 1D AND 1F MODE REPLY11AB36 AYTFJ T10RANGE,TEMP,OPERATING,CABINET CABINET OPERATING TEMP RANGE THE MINIMUM AND MAXIMUM LIMITS OF OPERATING TEMPERATURE AT WHICH THE CABINET IS RATED. 1D AND 1F MODE REPLY11AB36 AYTGD /D/ 07BIN,VEGETABLE VEGETABLE BIN AN INDICATION OF WHETHER OR NOT A VEGETABLE BIN IS INCLUDED. SELECT REPLY CODE 10AA49 AYTHD 11METHOD,GENERATING,HEAT HEAT GENERATING METHOD THE MEANS BY WHICH THE HEAT IS GENERATED. SELECT REPLY CODE 10AM63 AYTJB 04ANGLE IN DEG,PRESSURE PRESSURE ANGLE IN DEG THE PRESSURE ANGLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AYTKD 18TYPE,SHANK,SHAFT SHAFT SHANK TYPE INDICATES THE TYPE OF SHAFT SHANK PROVIDED. SELECT REPLY CODE 10AH09 AYTLD /D/ 18TYPE,UNIT,CONDENSER CONDENSER UNIT TYPE INDICATES THE TYPE OF CONDENSER UNIT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 AYTMD 08LOCATION,UNIT UNIT LOCATION INDICATES THE LOCATION OF THE UNIT. SELECT REPLY CODE 10AJ91 AYTND 13THREAD SERIES,SHANK SHANK THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF A THREADED SHANK. SELECT REPLY CODE 10AH06 AYTPD /D/ 18TYPE,CURRENT,SOLENOID SOLENOID CURRENT TYPE INDICATES THE TYPE OF CURRENT FOR WHICH THE SOLENOID IS DESIGNED. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AB62 AYTQB /D/ 10VOLTAGE RATING,SOLENOID SOLENOID VOLTAGE RATING THE VALUE/S/ OF POTENTIAL FOR WHICH THE SOLENOID IS RATED. 1B MODE REPLY 0 AYTRD 02DESIGN,ARM,CONNECTING CONNECTING ARM DESIGN THE DESIGN OF THE CONNECTING ARM. SELECT REPLY CODE 10AG26 AYTSD 18TYPE,COOLING COOLING TYPE INDICATES THE TYPE OF COOLING. SELECT REPLY CODE 10AB75 AYTTD 05DIRECTION,OFFSET OFFSET DIRECTION AN INDICATION OF THE OFFSET DIRECTION IN RELATION TO THE ITEM. SELECT REPLY CODE 10AL96 AYTWA 12QUANTITY,HOLE,CONNECTING ARM CONNECTING ARM HOLE QUANTITY THE NUMBER OF CONNECTING ARM HOLES PROVIDED ON THE ITEM. 1A MODE REPLY 0 AYTXD /D/ 07BUSHING,HOLE,CONNECTING ARM CONNECTING ARM HOLE BUSHING AN INDICATION OF WHETHER OR NOT A CONNECTING ARM HOLE BUSHING(S) IS INCLUDED. SELECT REPLY CODE 10AA49 AYTYJ 04DIAMETER,SMALLEST SMALLEST DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE SMALLEST CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AYTZJ 04TAPER,HOLE HOLE TAPER THE DIMINISHING MEASUREMENT OF THE DIAMETER ALONG THE MAJOR AXIS OF THE HOLE. 2D AND 1B MODE REPLY22AG201AC20 AYWAJ 04DISTANCE BETWEEN SPLINE HOLE AND CONNECTION HOLE,CENTER TO CENTER,CONNECTING ARM CONNECTING ARM CENTER TO CENTER DISTANCE BETWEEN SPLINE HOLE AND CONNECTION HOLE THE DISTANCE FROM THE CENTER OF THE SPLINED HOLE TO THE CENTER OF THE CONNECTION HOLE ON THE CONNECTING ARM. 2D AND 1B MODE REPLY21AA051AC20 AYWBJ 04THICKNESS,ARM,CONNECTING CONNECTING ARM THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A CONNECTING ARM,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AYWCA 12QUANTITY,LID LID QUANTITY THE NUMBER OF LIDS PROVIDED. 1A MODE REPLY 0 AYWDA 12QUANTITY,GENERATOR,TRACTION TRACTION GENERATOR QUANTITY THE NUMBER OF TRACTION GENERATORS PROVIDED. 1A MODE REPLY 0 AYWEG 19NAME,MANUFACTURER,TRACTION GENERATOR TRACTION GENERATOR MANUFACTURER NAME THE NAME OF THE MANUFACTURER OF THE TRACTION GENERATOR FURNISHED. FULL TEXT WRITE-IN 0 AYWFG /D/ 19NUMBER,IDENTIFYING,TRACTION GENERATOR MANUFACTURER TRACTION GENERATOR MANUFACTURER IDENTIFYING NUMBER THE NUMBER USED BY THE MANUFACTURER FOR IDENTIFYING THE TRACTION GENERATOR. FULL TEXT WRITE-IN 0 AYWGA 12QUANTITY,MOTOR,TRACTION TRACTION MOTOR QUANTITY THE NUMBER OF TRACTION MOTORS PROVIDED. 1A MODE REPLY 0 AYWHG 19NAME,MANUFACTURER,TRACTION MOTOR TRACTION MOTOR MANUFACTURER NAME THE NAME OF THE MANUFACTURER OF THE TRACTION MOTOR FURNISHED. FULL TEXT WRITE-IN 0 AYWJG /D/ 19NUMBER,IDENTIFYING,TRACTION MOTOR MANUFACTURER TRACTION MOTOR MANUFACTURER IDENTIFYING NUMBER THE NUMBER USED BY THE MANUFACTURER FOR IDENTIFYING THE TRACTION MOTOR. FULL TEXT WRITE-IN 0 AYWKD 18TYPE,EQUIPMENT,BRAKE BRAKE EQUIPMENT TYPE INDICATES THE TYPE OF BRAKE EQUIPMENT FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AG25 AYWLA 19NUMBER,SCHEDULE SCHEDULE NUMBER THE SCHEDULE NUMBER CONTAINING THE PRINTED LIST OF THE MANUFACTURER. 1A MODE REPLY 0 AYWMD 11METHOD,TRACTION MOTOR DRIVE TO AXLE DRIVE COUPLING TRACTION MOTOR DRIVE TO AXLE DRIVE COUPLING METHOD THE MEANS USED TO TRANSMIT THE DRIVING EFFORT TO THE AXLE FROM THE TRACTION MOTOR. SELECT REPLY CODE 10AE15 AYWND 11METHOD BETWEEN AXLES,DRIVE,DRIVE COUPLING DRIVE COUPLING DRIVE METHOD BETWEEN AXLES THE MEANS BY WHICH THE DRIVING EFFORT IS TRANSMITTED BETWEEN AXLES. SELECT REPLY CODE 10AL40 AYWPD 19ARRANGEMENT,COUPLER COUPLER ARRANGEMENT A DESIGNATION THAT IDENTIFIES THE ARRANGEMENT USED TO COUPLE ONE ITEM TO ANOTHER. SELECT REPLY CODE 10AM64 AYWQJ 10FORCE ON LEVEL TANGENT TRACK,TRACTIVE,MAXIMUM MAXIMUM TRACTIVE FORCE ON LEVEL TANGENT TRACK THE MOTIVE POWER REQUIRED TO PROVIDE THE ADHESIVE FRICTION OF A BODY ON A SURFACE ON WHICH IT MOVES. 1D AND 1B MODE REPLY12AG67 AYWRG 10FORCE ON LEVEL TANGENT TRACK,TRACTIVE,CONTINUOUS CONTINUOUS TRACTIVE FORCE ON LEVEL TANGENT TRACK THE MOTIVE POWER REQUIRED TO SUSTAIN THE MOVEMENT OF A BODY ON A SURFACE ON WHICH IT MOVES. FULL TEXT WRITE-IN 0 AYWSJ 10SPEED,NO LOAD,MAXIMUM MAXIMUM NO LOAD SPEED THE MAXIMUM SPEED AT WHICH AN ITEM CAN BE OPERATED UNDER NO LOAD CONDITIONS. 1D AND 1B MODE REPLY11AA34 AYWTJ 04LENGTH,OVERALL,INCLUDING PROTRUSIONS OVERALL LENGTH INCLUDING PROTRUSIONS THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM,INCLUDING ALL PROTRUSIONS. 2D AND 1B MODE REPLY21AA053AM65 AYWWG /D/ 19SYMBOL,CIRCUIT,ITEM ITEM CIRCUIT SYMBOL AN INDICATION OF THE DESIGN USED ON DIAGRAMS TO REPRESENT A COMPONENT OR IDENTIFY SPECIFIC CHARACTERISTICS,NUMBER OF ITEMS,OR OBJECTS OF THE ITEM. FULL TEXT WRITE-IN 0 AYWXJ 10SPEED,HOIST,MAIN MAIN HOIST SPEED THE RATED SPEED OF THE MAIN HOIST. 1D AND 1B MODE REPLY11AA22 AYWYJ 10SPEED,HOIST,AUXILIARY AUXILIARY HOIST SPEED THE RATED SPEED OF THE AUXILIARY HOIST. 1D AND 1B MODE REPLY11AA22 AYWZJ 04LENGTH,BOOM BOOM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BOOM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AYXAJ 04RADIUS,WORKING,MAXIMUM,BOOM BOOM MAXIMUM WORKING RADIUS THE MAXIMUM WORKING RADIUS OF THE BOOM. 1D AND 1B MODE REPLY11AA05 AYXBJ 04RADIUS,WORKING,MINIMUM,BOOM BOOM MINIMUM WORKING RADIUS THE MINIMUM WORKING RADIUS OF THE BOOM. 1D AND 1B MODE REPLY11AA05 AYXCJ 10SPEED,TRAVELING,MAXIMUM MAXIMUM TRAVELING SPEED THE MAXIMUM RATED TRAVELING SPEED OF THE ITEM. 1D AND 1B MODE REPLY11AA22 AYXDD /D/ 19CONFIGURATION,WHEEL,TRUCK TRUCK WHEEL CONFIGURATION THE CONFIGURATION OF THE TRUCK WHEEL/S/ ON THE ITEM. SELECT REPLY CODE 10AM67 AYXED 18TYPE,BRAKE,POWER POWER BRAKE TYPE INDICATES THE TYPE OF POWER BRAKE FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AG25 AYXFD /D/ 07BRAKE,HAND HAND BRAKE AN INDICATION OF WHETHER OR NOT A HAND BRAKE IS PROVIDED. SELECT REPLY CODE 10AB22 AYXGD 08LOCATION,BRAKE,HAND HAND BRAKE LOCATION INDICATES THE LOCATION OF THE HAND BRAKE ON THE ITEM. SELECT REPLY CODE 10AJ91 AYXHA 12QUANTITY,WHEEL,HAND BRAKE APPLICATION HAND BRAKE APPLICATION WHEEL QUANTITY THE NUMBER OF WHEELS TO WHICH THE HAND BRAKE IS APPLIED. 1A MODE REPLY 0 AYXJG 03DESIGNATOR,DIAGRAM,CLEARANCE CLEARANCE DIAGRAM DESIGNATOR A DESIGNATION INDICATING A GRAPHIC REPRESENTATION IN STANDARD AND ACCEPTED SYMBOLS OF THE MAXIMUM PERMISSIBLE WIDTH AND HEIGHT OF RAILWAY EQUIPMENT. FULL TEXT WRITE-IN 0 AYXKJ 10LOAD RATING,MAXIMUM MAXIMUM LOAD RATING THE MAXIMUM RATED LOAD THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY12AG67 AYXLD 19CONSTRUCTION,SHEATHING SHEATHING CONSTRUCTION THE STRUCTURAL CHARACTERISTIC OF THE SHEATHING. SELECT REPLY CODE 10AL59 AYXMD /D/ 09MATERIAL,SHEATHING,OUTSIDE OUTSIDE SHEATHING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE OUTSIDE SHEATHING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AYXND 18TYPE,CLOSURE,DOOR DOOR CLOSURE TYPE INDICATES THE TYPE OF CLOSURE PROVIDED FOR THE DOOR. SELECT REPLY CODE 10AM35 AYXPD 08LOCATION,DOOR DOOR LOCATION INDICATES THE LOCATION OF THE DOOR ON THE ITEM. SELECT REPLY CODE 10AJ91 AYXQJ 04WIDTH,OPENING,DOOR DOOR OPENING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE HEIGHT OF THE DOOR UPRIGHTS. 1D AND 1B MODE REPLY11AA05 AYXRD 18TYPE FOR WHICH DESIGNED,CARGO CARGO TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF CARGO FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AG36 AYXSD /D/ 09MATERIAL,PLATFORM PLATFORM MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PLATFORM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AYXTJ 04LENGTH,PLATFORM PLATFORM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE PLATFORM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AYXWJ 04WIDTH,PLATFORM PLATFORM WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PLATFORM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AYXXJ 04HEIGHT FROM RAIL TO PLATFORM TOP HEIGHT FROM RAIL TO PLATFORM TOP A MEASUREMENT FROM RAIL TO TOP OF PLATFORM,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 AYXYA 19CLASSIFICATION,INTERSTATE COMMERCE COMMISSION INTERSTATE COMMERCE COMMISSION CLASSIFICATION THE INTERSTATE COMMERCE COMMISSION SPECIFICATION OR STANDARD NUMBER GOVERNING THE ITEM. 1A MODE REPLY 0 AYXZJ 10OUTPUT RATING,POWER,MODULATOR MODULATOR POWER OUTPUT RATING THE RATED POWER OUTPUT FOR WHICH THE MODULATOR IS DESIGNED. 1D AND 1B MODE REPLY11AC33 AYYAA 12QUANTITY,CHANNEL,INPUT,MODULATOR MODULATOR INPUT CHANNEL QUANTITY THE NUMBER OF MODULATOR INPUT CHANNELS PROVIDED. 1A MODE REPLY 0 AYYBJ 10IMPEDANCE RATING,CHANNEL,INPUT,MODULATOR MODULATOR INPUT CHANNEL IMPEDANCE RATING THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) WHICH THE MODULATOR INPUT CHANNEL(S) OFFERS TO THE ADMITTANCE OF AN ENTERING FLOW OF ALTERNATING CURRENT. 1D AND 1B MODE REPLY12AE75 AYYCD 02DESIGN,OSCILLATOR OSCILLATOR DESIGN THE DESIGN OF THE OSCILLATOR. SELECT REPLY CODE 10AK80 AYYDD 18TYPE,OSCILLATOR OSCILLATOR TYPE INDICATES THE TYPE OF OSCILLATOR PROVIDED. SELECT REPLY CODE 10AD63 AYYED 18TYPE,MODULATION MODULATION TYPE INDICATES THE TYPE OF MODULATION PROVIDED. SELECT REPLY CODE 10AJ52 AYYFJ 10FREQUENCY RATING,OSCILLATOR OSCILLATOR FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE OSCILLATOR IS DESIGNED. 2D AND 1B MODE REPLY21AC321AC20 AYYGA 12QUANTITY,BAND,OSCILLATOR OSCILLATOR BAND QUANTITY THE NUMBER OF OSCILLATOR BANDS PROVIDED. 1A MODE REPLY 0 AYYHG /D/ 12QUANTITY AND FREQUENCY,CHANNEL,INDIVIDUAL,OSCILLATOR OSCILLATOR INDIVIDUAL CHANNEL QUANTITY AND FREQUENCY THE NUMBER OF CHANNELS AND COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE OSCILLATOR IS RATED. FULL TEXT WRITE-IN 0 AYYJJ 10FREQUENCY RATING,AMPLIFIER AMPLIFIER FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE AMPLIFIER IS RATED. 2D AND 1B MODE REPLY21AC321AC20 AYYKD 18TYPE,RECTIFIER,DETECTOR DETECTOR RECTIFIER TYPE INDICATES THE TYPE OF DETECTOR RECTIFIER PROVIDED. SELECT REPLY CODE 10AK80 AYYLA 12QUANTITY,INPUT INPUT QUANTITY THE NUMBER OF INPUTS PROVIDED. 1A MODE REPLY 0 AYYMA 12QUANTITY,OUTPUT OUTPUT QUANTITY THE NUMBER OF OUTPUTS PROVIDED. 1A MODE REPLY 0 AYYNJ 10OUTPUT RATING,POWER POWER OUTPUT RATING THE RATED POWER OUTPUT FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AC331AC20 AYYPD /D/ 09MATERIAL,SURFACE,INNER INNER SURFACE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INNER SURFACE OF AN ITEM IS FABRICATED. SELECT REPLY CODE 10AD09 AYYQG /D/ 11METHOD,TAKEOFF,POWER POWER TAKEOFF METHOD THE POWER TAKEOFF METHOD USED TO TRANSMIT. FULL TEXT WRITE-IN 0 AYYRD /D/ 07FACILITY,TUNING TUNING FACILITY AN INDICATION OF WHETHER OR NOT A TUNING FACILITY IS PROVIDED. SELECT REPLY CODE 10AB22 AYYSA 12QUANTITY,PAIR,TERMINAL TERMINAL PAIR QUANTITY THE NUMBER OF TERMINAL PAIRS PROVIDED. 1A MODE REPLY 0 AYYTD /D/ 07STUB,CABLE CABLE STUB AN INDICATION OF WHETHER OR NOT A CABLE STUB IS INCLUDED. SELECT REPLY CODE 10AA49 AYYWD /D/ 07STRIP,FANNING FANNING STRIP AN INDICATION OF WHETHER OR NOT A FANNING STRIP IS INCLUDED. SELECT REPLY CODE 10AA49 AYYXD /D/ 07LINES,FUSED FUSED LINES AN INDICATION OF WHETHER OR NOT FUSED LINES ARE PROVIDED. SELECT REPLY CODE 10AB22 AYYYD /D/ 07ARRESTER,LIGHTNING LIGHTNING ARRESTER AN INDICATION OF WHETHER OR NOT A LIGHTNING ARRESTER IS INCLUDED. SELECT REPLY CODE 10AA49 AYYZD /D/ 07INCLOSURE,BOX,TERMINAL TERMINAL BOX INCLOSURE AN INDICATION OF WHETHER OR NOT A TERMINAL BOX INCLOSURE IS PROVIDED. SELECT REPLY CODE 10AB22 AYZAD /D/ 09MATERIAL,BOX,TERMINAL TERMINAL BOX MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TERMINAL BOX IS FABRICATED. SELECT REPLY CODE 10AD09 AYZBD /D/ 07CONNECTION,PRESSURIZATION PRESSURIZATION CONNECTION AN INDICATION OF WHETHER OR NOT A PRESSURIZATION CONNECTION IS INCLUDED. SELECT REPLY CODE 10AA49 AYZCD 18TYPE,ACTUATION,MANUAL MANUAL ACTUATION TYPE INDICATES THE TYPE OF MANUAL ACTUATION PROVIDED. SELECT REPLY CODE 10AC82 AYZDD /D/ 18TYPE,POSITION POSITION TYPE INDICATES THE POSITION TYPE PROVIDED. SELECT REPLY CODE 10AD63 AYZEB 10ROTATION IN DEG,STOP STOP ROTATION IN DEG AN INDICATION OF THE DEGREE OF ROTATION BETWEEN STOPS. 1B MODE REPLY 0 AYZGA 19AGENCY,CONTROLLING,IMMEDIATE EQUIPMENT IMMEDIATE EQUIPMENT CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE IMMEDIATE EQUIPMENT. 1A MODE REPLY 0 AYZHG 19NAME,EQUIPMENT,IMMEDIATE IMMEDIATE EQUIPMENT NAME THE NAME OF THE IMMEDIATE EQUIPMENT. FULL TEXT WRITE-IN 0 AYZJJ A19NUMBER,IDENTIFYING,IMMEDIATE EQUIPMENT IMMEDIATE EQUIPMENT IDENTIFYING NUMBER THE NUMBER USED TO IDENTIFY THE IMMEDIATE EQUIPMENT. 1D AND 1A MODE REPLY12AG99 AYZKD /D/ 09MATERIAL,FRAME,MOUNTING MOUNTING FRAME MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MOUNTING FRAME IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AYZLA 12QUANTITY,JACK JACK QUANTITY THE NUMBER OF JACKS PROVIDED. 1A MODE REPLY 0 AYZMD 18TYPE,CONTACT,JACK JACK CONTACT TYPE INDICATES THE TYPE OF JACK CONTACT/S/ PROVIDED. SELECT REPLY CODE 10AC82 AYZPJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CONNECTION,INLET INLET CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE INLET CONNECTION. 1D AND 1A MODE REPLY12AH06 AYZQJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CONNECTION,OUTLET OUTLET CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE OUTLET CONNECTION. 1D AND 1A MODE REPLY12AH06 AYZRJ 04SIZE,CONNECTION,SUCTION SUCTION CONNECTION SIZE DESIGNATES THE SIZE OF THE SUCTION CONNECTION INCLUDED ON THE ITEM. 1D AND 1B MODE REPLY12AH06 AYZSD /D/ 07FEATURE,COMBINATION,ENDLESS ENDLESS COMBINATION FEATURE AN INDICATION OF WHETHER OR NOT AN ENDLESS COMBINATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AYZTD /D/ 07FORM,ASSEMBLED,CABINET CABINET ASSEMBLED FORM AN INDICATION OF THE ASSEMBLED FORM OF THE CABINET. SELECT REPLY CODE 10AM27 AYZWD /D/ 07CANOPY,CABINET CABINET CANOPY AN INDICATION OF WHETHER OR NOT A CABINET CANOPY IS INCLUDED. SELECT REPLY CODE 10AA49 AYZXD /D/ 07SUPERSTRUCTURE,CABINET CABINET SUPERSTRUCTURE AN INDICATION OF WHETHER OR NOT A CABINET SUPERSTRUCTURE IS INCLUDED. SELECT REPLY CODE 10AA49 AYZYD /D/ 07ILLUMINATION,ELECTRIC,CABINET CABINET ELECTRIC ILLUMINATION AN INDICATION OF WHETHER OR NOT A CABINET ELECTRIC ILLUMINATION IS INCLUDED. SELECT REPLY CODE 10AA49 AYZZD /D/ 09MATERIAL,INSULATION,CABINET CABINET INSULATION MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CABINET INSULATION IS FABRICATED. SELECT REPLY CODE 10AD09 AZAAD /D/ 07EVAPORATOR EVAPORATOR AN INDICATION OF WHETHER OR NOT AN EVAPORATOR IS INCLUDED. SELECT REPLY CODE 10AA49 AZABD /D/ 07COOLING,AIR,FORCED FORCED AIR COOLING AN INDICATION OF WHETHER OR NOT FORCED AIR COOLING IS INCLUDED. SELECT REPLY CODE 10AA49 AZACB 10HORSEPOWER RATING,MOTOR,FAN FAN MOTOR HORSEPOWER RATING THE RATED HORSEPOWER OF THE FAN MOTOR. 1B MODE REPLY 0 AZADD 18TYPE,COOLING,CONDENSER CONDENSER COOLING TYPE INDICATES THE TYPE OF COOLING FOR WHICH THE CONDENSER IS DESIGNED. SELECT REPLY CODE 10AB75 AZAEA 12QUANTITY,UNIT,CONDENSER CONDENSER UNIT QUANTITY THE NUMBER OF CONDENSER UNITS PROVIDED. 1A MODE REPLY 0 AZAFD 18TYPE,DEVICE,LOCKING LOCKING DEVICE TYPE INDICATES THE TYPE OF DEVICE USED TO LOCK THE ITEM. SELECT REPLY CODE 10AE36 AZAGD 19PROVISION,LUBRICATION LUBRICATION PROVISION THE LUBRICATION PROVISION ON THE ITEM. SELECT REPLY CODE 10AB26 AZAHD 19FEATURE,SURFACE SURFACE FEATURE A NARRATIVE EXPRESSION USED TO DEFINE THE SURFACE OF THE ITEM. SELECT REPLY CODE 10AD20 AZAJD /D/ 18TYPE,CURRENT,AUXILIARY CONTACT AUXILIARY CONTACT CURRENT TYPE INDICATES THE TYPE OF CURRENT USED WITH THE CONTACT(S). SELECT REPLY CODE 10AB62 AZAKJ /D/ 10VOLTAGE RATING,CONTACT,MAIN MAIN CONTACT VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,OF VOLTAGE FOR WHICH THE MAIN CONTACT IS RATED. 2D AND 1B MODE REPLY21AB631AC20 AZALJ /D/ 10VOLTAGE RATING,CONTACT,AUXILIARY AUXILIARY CONTACT VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,OF VOLTAGE FOR WHICH THE AUXILIARY CONTACT IS RATED. 2D AND 1B MODE REPLY21AB631AC20 AZAMD /D/ 07CUP,SECONDARY SECONDARY CUP AN INDICATION OF WHETHER OR NOT A SECONDARY CUP IS INCLUDED. SELECT REPLY CODE 10AA49 AZAND /D/ 07RING,LOCKING LOCKING RING AN INDICATION OF WHETHER OR NOT A LOCKING RING IS INCLUDED. SELECT REPLY CODE 10AA49 AZAPD /D/ 07PROTECTOR,CUP CUP PROTECTOR AN INDICATION OF WHETHER OR NOT A CUP PROTECTOR IS INCLUDED. SELECT REPLY CODE 10AA49 AZAQD 08LOCATION,UNIT,CONDENSER CONDENSER UNIT LOCATION INDICATES THE LOCATION OF THE CONDENSER UNIT. SELECT REPLY CODE 10AJ91 AZARD 18TYPE,CONNECTION,ACTUATOR LINK ACTUATOR LINK CONNECTION TYPE INDICATES THE TYPE OF ACTUATOR LINK CONNECTION USED ON THE ITEM. SELECT REPLY CODE 10AJ57 AZASD /D/ 19SOURCE,POWER,CONDENSER OPERATING CONDENSER OPERATING POWER SOURCE THE SOURCE OF POWER WHICH OPERATES THE CONDENSER. SELECT REPLY CODE 10AG27 AZATB /D/ 10HORSEPOWER RATING,MOTOR,CONDENSER CONDENSER MOTOR HORSEPOWER RATING THE RATED HORSEPOWER OF THE CONDENSER MOTOR. 1B MODE REPLY 0 AZAWD /D/ 18TYPE,CURRENT,CONDENSER MOTOR CONDENSER MOTOR CURRENT TYPE INDICATES THE CURRENT TYPE OF THE CONDENSER MOTOR. SELECT REPLY CODE 10AB62 AZAXB /D/ 10VOLTAGE RATING IN VOLTS,MOTOR,CONDENSER CONDENSER MOTOR VOLTAGE RATING IN VOLTS THE ELECTRIC VOLTAGE FOR WHICH THE CONDENSER MOTOR IS RATED. 1B MODE REPLY 0 AZAYJ /D/ 10FREQUENCY RATING,MOTOR,CONDENSER CONDENSER MOTOR FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE CONDENSER MOTOR IS RATED. 2D AND 1B MODE REPLY21AC321AC20 AZAZD /D/ 10PHASE,MOTOR,CONDENSER CONDENSER MOTOR PHASE THE NUMBER OF ALTERNATING CURRENT CONDENSER MOTOR PHASES. SELECT REPLY CODE 10AD02 AZBAD /D/ 07EQUIPMENT,MAKING,ICE CUBE ICE CUBE MAKING EQUIPMENT AN INDICATION OF WHETHER OR NOT ICE CUBE MAKING EQUIPMENT IS INCLUDED. SELECT REPLY CODE 10AA49 AZBBA /D/ 16STYLE,END,LINK ROD CONNECTING LINK ROD CONNECTING END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LINK ROD CONNECTING END. 1A MODE REPLY 0 AZBCD /D/ 07EQUIPMENT,REFRIGERATING REFRIGERATING EQUIPMENT AN INDICATION OF WHETHER OR NOT REFRIGERATING EQUIPMENT IS INCLUDED. SELECT REPLY CODE 10AA49 AZBDD 18TYPE,EQUIPMENT EQUIPMENT TYPE INDICATES THE TYPE OF EQUIPMENT FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AM66 AZBED /D/ 18TYPE,DRIVE,EQUIPMENT EQUIPMENT DRIVE TYPE INDICATES THE TYPE OF DRIVE FOR WHICH THE EQUIPMENT IS DESIGNED. SELECT REPLY CODE 10AG25 AZBFA /D/ 16STYLE,END,PISTON SOCKET PISTON SOCKET END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PISTON SOCKET END. 1A MODE REPLY 0 AZBGD 18TYPE,ENGINE ENGINE TYPE INDICATES THE TYPE OF ENGINE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AG27 AZBHB 10HORSEPOWER RATING,ENGINE ENGINE HORSEPOWER RATING THE RATED HORSEPOWER OF THE ENGINE. 1B MODE REPLY 0 AZBJJ 04DIAMETER,ROD ROD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR ROD,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AZBKB 10HEAT REJECTED PER HOUR IN TONS OF REFRIGERATION,MAXIMUM MAXIMUM HEAT REJECTED PER HOUR IN TONS OF REFRIGERATION THE MAXIMUM RATE AT WHICH HEAT IS REJECTED PER HOUR,EXPRESSED IN TONS OF REFRIGERATION. 1B MODE REPLY 0 AZBLD /D/ 07ENGINE,GASOLINE,STAND-BY STAND-BY GASOLINE ENGINE AN INDICATION OF WHETHER OR NOT A STAND-BY GASOLINE ENGINE IS INCLUDED. SELECT REPLY CODE 10AA49 AZBMD /D/ 07FEATURE,STARTING,AUTOMATIC AUTOMATIC STARTING FEATURE AN INDICATION OF WHETHER OR NOT AN AUTOMATIC STARTING FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 AZBNG 19NAME,MANUFACTURER,PRIME MOVER PRIME MOVER MANUFACTURER NAME THE NAME OF THE MANUFACTURER OF THE PRIME MOVER. FULL TEXT WRITE-IN 0 AZBPJ A19NUMBER,IDENTIFYING,PRIME MOVER PRIME MOVER IDENTIFYING NUMBER THE NUMBER USED BY THE MANUFACTURER FOR IDENTIFYING THE PRIME MOVER. 1D AND 1A MODE REPLY12AG99 AZBQD 18TYPE,DESIGN,TURBINE TURBINE DESIGN TYPE INDICATES THE DESIGN TYPE CHARACTERISTIC/S/ OF THE TURBINE. SELECT REPLY CODE 10AM57 AZBRD 18TYPE,EXHAUST EXHAUST TYPE INDICATES THE TYPE OF EXHAUST PROVIDED. SELECT REPLY CODE 10AM42 AZBSD 11METHOD,COUPLING,TURBINE TO GENERATOR TURBINE TO GENERATOR COUPLING METHOD THE MEANS PROVIDED FOR COUPLING THE TURBINE TO THE GENERATOR. SELECT REPLY CODE 10AE15 AZBTL 16STYLE,ARRANGEMENT,WHEEL WHEEL ARRANGEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE WHEEL(S). 1L MODE REPLY 0 AZBWD /D/ 18TYPE,CONNECTION,HITCH HITCH CONNECTION TYPE INDICATES THE TYPE OF HITCH CONNECTION PROVIDED. SELECT REPLY CODE 10AB76 AZBXD /D/ 18TYPE,KINGPIN KINGPIN TYPE INDICATES THE TYPE OF KINGPIN PROVIDED ON THE ITEM. SELECT REPLY CODE 10AK54 AZBYL /D/ 16STYLE,HITCH/COUPLER HITCH/COUPLER STYLE THE SYTLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HITCH AND/OR COUPLER. 1L MODE REPLY 0 AZBZG /D/ 19NAME,MANUFACTURER,COMPRESSOR COMPRESSOR MANUFACTURER NAME THE NAME OF THE COMPRESSOR MANUFACTURER. FULL TEXT WRITE-IN 0 AZCAJ /D/A19NUMBER,IDENTIFYING,COMPRESSOR COMPRESSOR IDENTIFYING NUMBER THE IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE COMPRESSOR. 1D AND 1A MODE REPLY12AG99 AZCBD 18TYPE,HOUSING HOUSING TYPE INDICATES THE TYPE OF HOUSING PROVIDED. SELECT REPLY CODE 10AG85 AZCCD 18TYPE,SCAN,OUTPUT MOTION OUTPUT MOTION SCAN TYPE INDICATES THE TYPE OF OUTPUT MOTION SCAN PROVIDED. SELECT REPLY CODE 10AJ41 AZCDD /D/ 07EXCURSION,LIMITED,OUTPUT MOTION OUTPUT MOTION LIMITED EXCURSION AN INDICATION OF WHETHER OR NOT THE OUTPUT MOTION IS PROVIDED WITH A LIMITED EXCURSION. SELECT REPLY CODE 10AB22 AZCEB 10EXCURSION IN DEG,MOTION,OUTPUT OUTPUT MOTION EXCURSION IN DEG A MOVEMENT OUTWARD OR FROM A MEAN POSITION OR AXIS,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AZCFG 10SPEED,ROTATION ROTATION SPEED THE SPEED(S) OF ROTATION REQUIRED TO PRODUCE THE RATED CAPACITY OF THE ITEM. FULL TEXT WRITE-IN 0 AZCGG 19NAME,COMPONENT,ACCESSORY ACCESSORY COMPONENT NAME THE NAME OF THE ACCESSORY COMPONENT ASSIGNED BY THE CONTROLLING AGENCY. FULL TEXT WRITE-IN 0 AZCHD /D/ 07FACILITY,LEVELING LEVELING FACILITY AN INDICATION OF WHETHER OR NOT A LEVELING FACILITY(IES) IS PROVIDED. SELECT REPLY CODE 10AB22 AZCJA 12QUANTITY,MOTOR,INDIVIDUAL INDIVIDUAL MOTOR QUANTITY THE NUMBER OF INDIVIDUAL MOTORS PROVIDED. 1A MODE REPLY 0 AZCKG 19AGENCY,CONTROLLING,MOTOR MOTOR CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION THAT CONTROLS THE MANUFACTURE OF THE MOTOR. FULL TEXT WRITE-IN 0 AZCLB 10TEMP IN DEG CELSIUS,AMBIENT AMBIENT TEMP IN DEG CELSIUS THE AMBIENT TEMPERATURE OF THE MEDIUM SURROUNDING AN ITEM AT WHICH IT CAN BE OPERATED,EXPRESSED IN DEGREES CELSIUS. 1B MODE REPLY 0 AZCMB 10RISE RATING IN DEG CELSIUS FOR CONTINUOUS OPERATION,TEMP TEMP RISE RATING IN DEG CELSIUS FOR CONTINUOUS OPERATION THE PERMISSIBLE TEMPERATURE INCREASE FOR CONTINUOUS OPERATION,AT WHICH THE ITEM IS RATED,EXPRESSED IN DEGREES CELSIUS. 1B MODE REPLY 0 AZCNJ /D/ 10VOLTAGE RATING,PRIMARY,TRANSFORMER TRANSFORMER PRIMARY VOLTAGE RATING THE VOLTAGE VALUE FOR WHICH THE PRIMARY WINDING OF THE TRANSFORMER IS RATED. 2D AND 1B MODE REPLY21AB631AC20 AZCPJ /D/ 10VOLTAGE RATING,SECONDARY,TRANSFORMER TRANSFORMER SECONDARY VOLTAGE RATING THE VOLTAGE VALUE FOR WHICH THE SECONDARY WINDING OF THE TRANSFORMER IS RATED. 2D AND 1B MODE REPLY21AB631AC20 AZCQH /D/ 14SHAPE AND LOCATION SHAPE AND LOCATION THE PHYSICAL CONFIGURATION AND ITS LOCATION ON THE ITEM. 2D MODE REPLY 23AD073AJ91 AZCRJ 04DIAMETER,CIRCLE,MOUNTING FACILITY MOUNTING FACILITY CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING FACILITY CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AZCSJ 18TYPE AND RATING IN AMPS,CURRENT CURRENT TYPE AND RATING IN AMPS INDICATES THE TYPE AND AMOUNT OF ELECTRICAL FLOW AT WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN AMPERES. 2D AND 1B MODE REPLY21AB621AC20 AZCTJ 04HEIGHT,LEG,LONG LONG LEG HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AZCWJ 04HEIGHT,LEG,SHORT SHORT LEG HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AZCXJ /D/ 04DEPTH,ARC ARC DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AZCYJ 04DISTANCE BETWEEN LOOP AND MOUNTING HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 AZCZJ 04DISTANCE FROM LOOP CENTER TO SHORT TONGUE END DISTANCE FROM LOOP CENTER TO SHORT TONGUE END NONE. 2D AND 1B MODE REPLY21AA051AC20 AZDAJ 04WIDTH,LOOP LOOP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A LOOP,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AZDBJ 04LENGTH,LOOP LOOP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A LOOP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AZDCJ 04DISTANCE FROM LOOP CENTER TO TONGUE END DISTANCE FROM LOOP CENTER TO TONGUE END NONE. 2D AND 1B MODE REPLY21AA051AC20 AZDDJ /D/ 04WIDTH,LUG LUG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AZDEJ 04DISTANCE BETWEEN LOOP AND LUG HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN LOOP AND LUG HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 AZDFJ /D/ 04DISTANCE FROM HOLE TO CENTER EDGE DISTANCE FROM HOLE TO CENTER EDGE NONE. 2D AND 1B MODE REPLY21AA051AC20 AZDGJ /D/ 04DISTANCE BETWEEN FASTENERS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FASTENERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AZDHD /D/ 07EQUIPMENT,OPENING FOR PORTABLE REFRIGERATION OPENING FOR PORTABLE REFRIGERATION EQUIPMENT AN INDICATION OF WHETHER OR NOT AN OPENING FOR PORTABLE REFRIGERATION EQUIPMENT IS PROVIDED. SELECT REPLY CODE 10AB22 AZDJD /D/ 07REFRIGERANT,SECONDARY SECONDARY REFRIGERANT AN INDICATION OF WHETHER OR NOT A SECONDARY REFRIGERANT IS INCLUDED. SELECT REPLY CODE 10AA49 AZDKA 12QUANTITY,COMPRESSOR COMPRESSOR QUANTITY THE NUMBER OF COMPRESSORS INCLUDED. 1A MODE REPLY 0 AZDLD 18TYPE,COOLING,COMPRESSOR COMPRESSOR COOLING TYPE INDICATES THE TYPE OF COOLING FOR WHICH THE COMPRESSOR IS DESIGNED. SELECT REPLY CODE 10AB75 AZDMA /D/ 12QUANTITY,UNIT,COOLER COOLER UNIT QUANTITY THE NUMBER OF COOLER UNITS. 1A MODE REPLY 0 AZDND /D/ 07TOWER,COOLING COOLING TOWER AN INDICATION OF WHETHER OR NOT A COOLING TOWER IS INCLUDED. SELECT REPLY CODE 10AA49 AZDPD 08LOCATION,INSERTION,UNIT UNIT INSERTION LOCATION INDICATES THE LOCATION IN THE ITEM WHERE THE UNIT IS INSERTED. SELECT REPLY CODE 10AJ91 AZDQD /D/ 07PROJECTION,INSIDE,BASE BASE INSIDE PROJECTION AN INDICATION OF WHETHER OR NOT A PROJECTION INSIDE OF BASE IS INCLUDED. SELECT REPLY CODE 10AA49 AZDRD /D/ 07FEATURE,LIP,FEATHERED FEATHERED LIP FEATURE AN INDICATION OF WHETHER OR NOT A FEATHER LIP FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AZDSD /D/ 07GROOVE,BASE,OUTER PERIPHERY OUTER PERIPHERY BASE GROOVE AN INDICATION OF WHETHER OR NOT AN OUTER PERIPHERY BASE GROOVE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 AZDTJ 04LENGTH,LIP,SEALING SEALING LIP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SEALING LIP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AZDWD 11METHOD,MOUNTING,REMOTE UNIT REMOTE UNIT MOUNTING METHOD THE MEANS OF ATTACHING THE REMOTE UNIT. SELECT REPLY CODE 10AM39 AZDXD 18TYPE,END,SHOE CONNECTION SHOE CONNECTION END TYPE INDICATES THE TYPE OF SHOE CONNECTION END USED ON THE ITEM. SELECT REPLY CODE 10AB76 AZDYD /D/ 07FEATURE,MOUNTING,SKID,PANEL UNIT PANEL UNIT SKID MOUNTING FEATURE AN INDICATION OF WHETHER OR NOT A PANEL UNIT SKID MOUNTING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AZDZD /D/ 07FEATURE,MOUNTING,SKID,CONDENSER UNIT CONDENSER UNIT SKID MOUNTING FEATURE AN INDICATION OF WHETHER OR NOT A CONDENSING UNIT SKID MOUNTING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AZEAD 18TYPE,UNIT,EVAPORATOR EVAPORATOR UNIT TYPE INDICATES THE TYPE OF EVAPORATOR UNIT. SELECT REPLY CODE 10AK95 AZEBD /D/ 18TYPE,SHANK,PISTON END PISTON END SHANK TYPE INDICATES THE TYPE OF PISTON END SHANK. SELECT REPLY CODE 10AK54 AZECJ /D/ 10AREA,EFFECTIVE,STROKE STROKE EFFECTIVE AREA A MEASUREMENT OF THE EFFECTIVE AREA OF THE STROKE. 2D AND 1B MODE REPLY21AC511AC20 AZEDD /D/ 08LOCATION,INLET INLET LOCATION INDICATES THE LOCATION OF THE INLET ON THE ITEM. SELECT REPLY CODE 10AJ91 AZEEB /D/ 04ANGLE FROM BOTTOM OF VERTICAL CENTERLINE IN DEG,CENTER,OFF OFF CENTER ANGLE FROM BOTTOM OF VERTICAL CENTERLINE IN DEG THE ANGLE OF THE ITEM OFF CENTER FROM BOTTOM OF VERTICAL CENTERLINE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 AZEFJ A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,LINE CONNECTION LINE CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE LINE CONNECTION. 1D AND 1A MODE REPLY12AH06 AZEGA /D/ 16STYLE DESIGNATOR,CLEVIS CLEVIS STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CLEVIS. 1A MODE REPLY 0 AZEHJ /D/ 04DISTANCE BETWEEN SECOND AND THIRD HOLE DISTANCE BETWEEN SECOND AND THIRD HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 AZEJD /D/ 07PIN,CLEVIS CLEVIS PIN AN INDICATION OF WHETHER OR NOT A CLEVIS PIN IS INCLUDED. SELECT REPLY CODE 10AA49 AZEKJ /D/ 04DISTANCE TO SPECIFIED LOCATION,ROD END ROD END DISTANCE TO SPECIFIED LOCATION THE DISTANCE FROM THE ROD END TO A SPECIFIC LOCATION. 3D AND 1B MODE REPLY31AA051AC203AJ91 AZELD 18TYPE,DRIVE,EVAPORATOR FAN EVAPORATOR FAN DRIVE TYPE INDICATES THE TYPE OF DRIVE USED FOR THE EVAPORATOR FAN. SELECT REPLY CODE 10AG25 AZEMB 10HORSEPOWER RATING,MOTOR,EVAPORATOR FAN EVAPORATOR FAN MOTOR HORSEPOWER RATING THE RATED HORSEPOWER OF THE EVAPORATOR FAN MOTOR. 1B MODE REPLY 0 AZEND 18TYPE,DIAPHRAGM DIAPHRAGM TYPE INDICATES THE TYPE OF DIAPHRAGM USED ON THE ITEM. SELECT REPLY CODE 10AG25 AZEPJ 04DIAMETER,OUTSIDE,SMALLEST,SLEEVE SLEEVE SMALLEST OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SLEEVE,AND TERMINATES AT THE SMALLEST OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AZEQD /D/ 18TYPE,CURRENT,EVAPORATOR FAN MOTOR EVAPORATOR FAN MOTOR CURRENT TYPE INDICATES THE TYPE OF CURRENT REQUIRED TO OPERATE THE EVAPORATOR FAN MOTOR. SELECT REPLY CODE 10AB62 AZERB /D/ 10VOLTAGE IN VOLTS,MOTOR,EVAPORATOR FAN EVAPORATOR FAN MOTOR VOLTAGE IN VOLTS THE TOTAL ELECTRICAL VOLTAGE OF THE EVAPORATOR FAN MOTOR,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AZESD /D/ 07CUP,PISTON PISTON CUP AN INDICATION OF WHETHER OR NOT A PISTON CUP IS INCLUDED. SELECT REPLY CODE 10AA49 AZETD 18TYPE,END,SHOE ACTUATING SHOE ACTUATING END TYPE INDICATES THE TYPE OF SHOE ACTUATING END USED ON THE ITEM. SELECT REPLY CODE 10AK84 AZEWJ 04DISTANCE TO RAISED SEAT WEAR SURFACE,CLOSED END CLOSED END DISTANCE TO RAISED SEAT WEAR SURFACE THE CLOSED END DISTANCE TO THE RAISED SEAT WEAR SURFACE. 2D AND 1B MODE REPLY21AA051AC20 AZEXD /D/ 07INSERT,STEEL STEEL INSERT AN INDICATION OF WHETHER OR NOT A STEEL INSERT IS INCLUDED. SELECT REPLY CODE 10AA49 AZEYG /D/ 19AGENCY,CONTROLLING,END ITEM END ITEM CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE END ITEM. FULL TEXT WRITE-IN 0 AZEZG /D/ 19NUMBER,IDENTIFYING,END ITEM END ITEM IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE AGENCY CONTROLLING THE END ITEM. FULL TEXT WRITE-IN 0 AZFAJ /D/ 10FREQUENCY RATING,MOTOR,EVAPORATOR FAN EVAPORATOR FAN MOTOR FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE EVAPORATOR FAN MOTOR IS RATED. 2D AND 1B MODE REPLY21AC321AC20 AZFBD /D/ 10PHASE,MOTOR,EVAPORATOR FAN EVAPORATOR FAN MOTOR PHASE THE NUMBER OF ALTERNATING CURRENT PHASES OF THE EVAPORATOR FAN MOTOR. SELECT REPLY CODE 10AD02 AZFCJ 04SIZE,CONNECTION,DISCHARGE DISCHARGE CONNECTION SIZE DESIGNATES THE SIZE OF THE DISCHARGE CONNECTION INCLUDED ON THE ITEM. 1D AND 1B MODE REPLY12AH06 AZFDD /D/ 07MOTOR,ELECTRIC,SEPARATE SEPARATE ELECTRIC MOTOR AN INDICATION OF WHETHER OR NOT A SEPARATE ELECTRIC MOTOR IS INCLUDED. SELECT REPLY CODE 10AA49 AZFEG /D/ 19SPEC/STD,GOVERNMENT,CONNECTION CONNECTION GOVERNMENT SPEC/STD THE GOVERNMENT SPECIFICATION AND/OR STANDARD THAT SPECIFICALLY COVERS THE CONNECTION. FULL TEXT WRITE-IN 0 AZFFG 04SPACING,HOLE,BOLT BOLT HOLE SPACING THE SPACING IN THE ARRANGEMENT OF THE BOLT HOLES. FULL TEXT WRITE-IN 0 AZFGG 04SPACING,HOLE,MOUNTING BOLT MOUNTING BOLT HOLE SPACING THE SPACING IN THE ARRANGEMENT OF THE MOUNTING BOLT HOLES. FULL TEXT WRITE-IN 0 AZFHD /D/ 17SURFACE TREATMENT,HOUSING HOUSING SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. SELECT REPLY CODE 10AD09 AZFJJ 13THREAD QUANTITY,CONNECTION,SUCTION SUCTION CONNECTION THREAD QUANTITY A MEASUREMENT OF THE NUMBER OF THREADS ON THE SUCTION CONNECTION,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1D AND 1B MODE REPLY11AB39 AZFKJ 13THREAD QUANTITY,CONNECTION,DISCHARGE DISCHARGE CONNECTION THREAD QUANTITY A MEASUREMENT OF THE NUMBER OF THREADS ON THE DISCHARGE CONNECTION,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1D AND 1B MODE REPLY11AB39 AZFLA 19ARRANGEMENT,CONTACT,JACK JACK CONTACT ARRANGEMENT THE DESIGNATION IDENTIFYING THE SCHEMATIC DIAGRAM OF THE JACK CONTACT CONFIGURATION. 1A MODE REPLY 0 AZFMD 18TYPE,MATERIAL,MOUNTING STRIP MOUNTING STRIP MATERIAL TYPE INDICATES THE TYPE OF MATERIAL OF WHICH THE MOUNTING STRIP IS FABRICATED. SELECT REPLY CODE 10AD93 AZFNG /D/ 04SIZE,HOLE,MOUNTING MOUNTING HOLE SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSION OF THE MOUNTING HOLE. FULL TEXT WRITE-IN 0 AZFPD /D/ 07DESIGNATION,JACK JACK DESIGNATION AN INDICATION OF WHETHER OR NOT JACK DESIGNATIONS ARE INCLUDED. SELECT REPLY CODE 10AA49 AZFQG 19MARKING,DESIGNATION,JACK JACK DESIGNATION MARKING AN INDICATION OF THE DESIGNATED MARKING(S) ON THE JACK. FULL TEXT WRITE-IN 0 AZFRJ /D/ 10TEMP RATING,NOMINAL NOMINAL TEMP RATING THE NOMINAL VALUE WHICH EXPRESSES THE DEGREE OF CONTROLLED TEMPERATURE OF AN ITEM. 1D AND 1B MODE REPLY11AB36 AZFSD /D/ 07DEVICE,INDICATING,TEMP TEMP INDICATING DEVICE AN INDICATION OF WHETHER OR NOT A TEMPERATURE INDICATING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 AZFTD /D/ 07DEVICE,INDICATING,BUILT-IN TEMP BUILT-IN TEMP INDICATING DEVICE AN INDICATION OF WHETHER OR NOT A BUILT-IN TEMPERATURE INDICATING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 AZFXD 18TYPE,DEVICE,TEMP CONTROL TEMP CONTROL DEVICE TYPE INDICATES THE TYPE OF TEMPERATURE CONTROL DEVICE PROVIDED. SELECT REPLY CODE 10AH83 AZFYD 19CLASS,EMISSION EMISSION CLASS AN INDICATION OF THE EMISSION CLASS PROVIDED. SELECT REPLY CODE 10AF22 AZFZJ T10RANGE,FREQUENCY FREQUENCY RANGE THE RANGE OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE ITEM IS RATED. 1D AND 1F MODE REPLY11AC32 AZGAA /D/ 12QUANTITY,AMPLIFIER,TOTAL TOTAL AMPLIFIER QUANTITY THE TOTAL NUMBER OF AMPLIFIERS PROVIDED. 1A MODE REPLY 0 AZGBA 12QUANTITY,AMPLIFIER AMPLIFIER QUANTITY THE NUMBER OF AMPLIFIERS PROVIDED. 1A MODE REPLY 0 AZGCG 19AGENCY,CONTROLLING,AMPLIFIER AMPLIFIER CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE AMPLIFIER. FULL TEXT WRITE-IN 0 AZGDG /D/ 19NUMBER,IDENTIFYING,AMPLIFIER AMPLIFIER IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE AMPLIFIER. FULL TEXT WRITE-IN 0 AZGEG /D/ 03DESIGNATOR,TUBE,ELECTRON,ACCOMMODATED ACCOMMODATED ELECTRON TUBE DESIGNATOR THE DESIGNATION FOR ELECTRON TUBE/S/ THE ITEM IS DESIGNED TO ACCOMMODATE. FULL TEXT WRITE-IN 0 AZGFG /D/ 19DIMENSION,INSIDE,ACCOMMODATED END ACCOMMODATED END INSIDE DIMENSION A NARRATIVE EXPRESSION INDICATING THE INSIDE DIMENSIONS OF THE ACCOMMODATED END. FULL TEXT WRITE-IN 0 AZGGD 18TYPE ACCOMMODATED,FUSEHOLDER FUSEHOLDER TYPE ACCOMMODATED INDICATES THE TYPE OF FUSEHOLDER THAT THE ITEM WILL ACCOMMODATE. SELECT REPLY CODE 10AE67 AZGHD /D/ 07RETAINING DEVICE,ADAPTER ADAPTER RETAINING DEVICE AN INDICATION OF WHETHER OR NOT AN ADAPTER RETAINING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 AZGJD /D/ 07DEVICE,RETAINING,FUSE FUSE RETAINING DEVICE AN INDICATION OF WHETHER OR NOT A FUSE RETAINING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 AZGKJ 04DIAMETER,CROSS-SECTIONAL CROSS-SECTIONAL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CROSS SECTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AZGLD 11METHOD,CONNECTION,TEST ITEM TEST ITEM CONNECTION METHOD THE MEANS USED FOR CONNECTING THE ITEM TO BE TESTED. SELECT REPLY CODE 10AK93 AZGMD 19FACILITY,MOUNTING MOUNTING FACILITY THE FACILITY FOR MOUNTING THE ITEM. SELECT REPLY CODE 10AM39 AZGND 19POSITION,TANK TANK POSITION THE POSITION OF THE TANK ON THE ITEM. SELECT REPLY CODE 10AE25 AZGPD /D/ 07HOUSING IN ACCORDANCE WITH NEMA STANDARD HOUSING IN ACCORDANCE WITH NEMA STANDARD AN INDICATION OF WHETHER OR NOT A HOUSING IN ACCORDANCE WITH NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION STANDARD IS PROVIDED. SELECT REPLY CODE 10AB22 AZGQA 03DESIGNATION,DESIGN,FRAME,NEMA NEMA FRAME DESIGN DESIGNATION THE DESIGN DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FRAME,ASSIGNED BY THE NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION. 1A MODE REPLY 0 AZGRA 19NUMBER,IDENTIFYING,FRAME,NEMA NEMA FRAME IDENTIFYING NUMBER THE IDENTIFYING NUMBER ASSIGNED TO THE FRAME BY THE NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION. 1A MODE REPLY 0 AZGSD /D/ 07PIECES,POLE,DIRECT CURRENT DIRECT CURRENT POLE PIECES AN INDICATION OF WHETHER OR NOT DIRECT CURRENT POLE PIECES ARE INCLUDED. SELECT REPLY CODE 10AA49 AZGTD /D/ 07SUPPORTS,WINDING,ALTERNATING CURRENT ALTERNATING CURRENT WINDING SUPPORTS AN INDICATION OF WHETHER OR NOT ALTERNATING CURRENT WINDING SUPPORTS ARE INCLUDED. SELECT REPLY CODE 10AA49 AZGWG 19CONFIGURATION,MOUNTING,END BELL END BELL MOUNTING CONFIGURATION THE NARRATIVE EXPRESSION USED FOR INDICATING THE CONFIGURATION OF THE END BELL/S/ MOUNTING FACILITIES. FULL TEXT WRITE-IN 0 AZGXD /D/ 19FACILITY,MOUNTING,MAIN,END ITEM END ITEM MAIN MOUNTING FACILITY THE END ITEM FOR WHICH THE MAIN MOUNTING FACILITY/IES/ IS DESIGNED. SELECT REPLY CODE 10AM43 AZGYD 19CONSTRUCTION,TANK TANK CONSTRUCTION THE STRUCTURAL CHARACTERISTIC OF THE TANK. SELECT REPLY CODE 10AL59 AZGZD 19CONSTRUCTION,SIDE SIDE CONSTRUCTION THE STRUCTURAL CHARACTERISTIC OF THE SIDE. SELECT REPLY CODE 10AL59 AZHAD 18TYPE,END,BODY BODY END TYPE INDICATES THE TYPE OF BODY END(S) ON THE ITEM. SELECT REPLY CODE 10AJ17 AZHBD 05DIRECTION,DROP,HINGED END HINGED END DROP DIRECTION AN INDICATION OF THE DIRECTION IN WHICH THE HINGED END DROPS. SELECT REPLY CODE 10AC50 AZHCD 18TYPE,SIDE,BODY BODY SIDE TYPE INDICATES THE TYPE OF BODY SIDE(S) ON THE ITEM. SELECT REPLY CODE 10AJ17 AZHDD /D/ 18TYPE,DOOR,HINGED HINGED DOOR TYPE INDICATES THE TYPE OF HINGED DOOR FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AD27 AZHED /D/ 11METHOD,OPENING,HINGED DOOR HINGED DOOR OPENING METHOD THE MEANS USED TO OPEN THE HINGED DOOR/S/. SELECT REPLY CODE 10AH25 AZHFJ /D/ 04WIDTH,OPENING,HINGED DOOR HINGED DOOR OPENING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE HINGED DOOR OPENING,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AZHGD 18TYPE,BOTTOM,BODY BODY BOTTOM TYPE INDICATES THE TYPE OF BODY BOTTOM ON THE ITEM. SELECT REPLY CODE 10AJ17 AZHHA /D/ 12QUANTITY,DOOR,BOTTOM DROP BOTTOM DROP DOOR QUANTITY THE NUMBER OF BOTTOM DROP DOORS PROVIDED ON THE ITEM. 1A MODE REPLY 0 AZHJD /D/ 08LOCATION,HINGE,BOTTOM DROP DOOR BOTTOM DROP DOOR HINGE LOCATION INDICATES THE LOCATION OF THE BODY TO WHICH THE BOTTOM DROP DOOR HINGE IS APPLIED. SELECT REPLY CODE 10AJ91 AZHKA 19CAPACITY,PASSENGER PASSENGER CAPACITY THE NUMBER OF PASSENGERS THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 AZHLD 19CONSTRUCTION,BODY BODY CONSTRUCTION THE STRUCTURAL CHARACTERISTIC OF THE BODY. SELECT REPLY CODE 10AL59 AZHMD /D/ 09MATERIAL,AXLE AXLE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE AXLE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AZHND 19CONSTRUCTION,AXLE AXLE CONSTRUCTION THE STRUCTURAL CHARACTERISTIC(S) OF THE AXLE. SELECT REPLY CODE 10AL59 AZHPD /D/ 06HEAT TREATMENT,AXLE AXLE HEAT TREATMENT A COMBINATION OF TIMED HEATING AND COOLING OPERATIONS APPLIED FOR THE PURPOSE OF ANNEALING OR HARDENING THE AXLE. SELECT REPLY CODE 10AD05 AZHQJ 04LENGTH,OVERALL,AXLE AXLE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE AXLE. 2D AND 1B MODE REPLY21AA051AC20 AZHRD 19CONDITION,SURFACE,JOURNAL JOURNAL SURFACE CONDITION THE CONDITION OF THE JOURNAL WITH RESPECT TO THE TEXTURE OF THE SURFACE. SELECT REPLY CODE 10AK39 AZHSJ 04DIAMETER,JOURNAL JOURNAL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A JOURNAL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AZHTJ 04LENGTH,JOURNAL JOURNAL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE JOURNAL,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AZHWD /D/ 08LOCATION IN RELATION TO WHEEL SEAT,JOURNAL JOURNAL LOCATION IN RELATION TO WHEEL SEAT INDICATES THE LOCATION OF THE JOURNAL AS RELATED TO THE WHEEL SEAT/S/. SELECT REPLY CODE 10AJ91 AZHXD /D/ 07PLATE,WEAR WEAR PLATE AN INDICATION OF WHETHER OR NOT A WEAR PLATE(S) IS INCLUDED. PLEASE USE MRC ABFF FOR ITEMS THAT HAD INCLUDED ANSWERED IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AZHYD /D/ 07SEAT,EQUALIZER,INTEGRAL INTEGRAL EQUALIZER SEAT AN INDICATION OF WHETHER OR NOT AN INTEGRAL EQUALIZER SEAT(S) IS PROVIDED. PLEASE USE MRC ABFF FOR ITEMS THAT HAD INCLUDED ANSWERED IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB22 AZHZD 18TYPE FOR WHICH DESIGNED,BEARING BEARING TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF BEARING FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AB81 AZJAD /D/ 02DESIGN BETWEEN WHEEL SEATS,BODY BODY DESIGN BETWEEN WHEEL SEATS THE DESIGN OF THE BODY OF THE ITEM BETWEEN THE WHEEL SEATS. SELECT REPLY CODE 10AE98 AZJBD /D/ 07COLLAR,SEAT,WHEEL WHEEL SEAT COLLAR AN INDICATION OF WHETHER OR NOT THE WHEEL SEAT INCLUDES A COLLAR. SELECT REPLY CODE 10AA49 AZJCD 18TYPE,WEAR,WHEEL WHEEL WEAR TYPE INDICATES THE TYPE OF WEAR FOR WHICH THE WHEEL IS DESIGNED. SELECT REPLY CODE 10AK54 AZJDG 19CONDITION CORRECTED,WEAR,WHEEL WHEEL WEAR CONDITION CORRECTED THE CONDITION OF THE WHEEL WEAR TO BE CORRECTED BY THE ITEM. FULL TEXT WRITE-IN 0 AZJED /D/ 09MATERIAL,WHEEL WHEEL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WHEEL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AZJFD 08LOCATION,TREATMENT,WHEEL WHEEL TREATMENT LOCATION INDICATES THE LOCATION ON THE WHEEL TO WHICH TREATMENT IS APPLIED. SELECT REPLY CODE 10AJ91 AZJGJ /D/ 10WEIGHT,WHEEL WHEEL WEIGHT A RELATIVE MEASURE OF THE MASS OF A WHEEL WITH RESPECT TO ITS DENSITY. 1D AND 1B MODE REPLY12AG67 AZJHD /D/ 07SURFACE FOR DRIVING GEAR,MACHINED MACHINED SURFACE FOR DRIVING GEAR AN INDICATION OF WHETHER OR NOT A MACHINED SURFACE FOR DRIVING GEAR IS INCLUDED. SELECT REPLY CODE 10AA49 AZJJD 19CONDITION,SURFACE,BORE BORE SURFACE CONDITION THE CONDITION OF THE BORE WITH RESPECT TO THE TEXTURE OF THE SURFACE. SELECT REPLY CODE 10AK39 AZJKJ 04WIDTH,HUB,BORE BORE HUB WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BORE HUB,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AZJLJ 04DIAMETER,SEAT,WHEEL WHEEL SEAT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WHEEL SEAT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AZJMJ 04LENGTH,SEAT,WHEEL WHEEL SEAT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE WHEEL SEAT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AZJNJ 10WEIGHT ACCOMMODATED,RAIL RAIL WEIGHT ACCOMMODATED THE WEIGHT OF THE RAIL/S/ THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY12AG67 AZJPG 19AGENCY,CONTROLLING,RAIL RAIL CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE RAIL. FULL TEXT WRITE-IN 0 AZJQD 03DESIGNATION,SOURCE,RAIL RAIL SOURCE DESIGNATION A DESIGNATION ASSIGNED TO THE RAIL SOURCE FOR PURPOSE OF READY IDENTIFICATION. SELECT REPLY CODE 10AM64 AZJRJ 04WIDTH ACCOMMODATED,BASE,RAIL RAIL BASE WIDTH ACCOMMODATED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE RAIL BASE THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AZJTJ /D/ 04DIAMETER,MAJOR,LUG LUG MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AZJWJ /D/ 04HEIGHT,MAJOR MAJOR HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AZJXD /D/ 07SYSTEM,DEFROST DEFROST SYSTEM AN INDICATION OF WHETHER OR NOT A DEFROST SYSTEM IS INCLUDED. SELECT REPLY CODE 10AA49 AZJYD 18TYPE,SYSTEM,DEFROST DEFROST SYSTEM TYPE INDICATES THE TYPE OF DEFROST SYSTEM FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AB75 AZJZJ /D/ 04THICKNESS,END,TAPERED TAPERED END THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AZKAA 12QUANTITY,MOTOR-GENERATOR,INDIVIDUAL INDIVIDUAL MOTOR-GENERATOR QUANTITY THE NUMBER OF MOTOR-GENERATORS PROVIDED. 1A MODE REPLY 0 AZKBD 18TYPE,CURRENT,FAN MOTOR FAN MOTOR CURRENT TYPE INDICATES THE TYPE OF CURRENT REQUIRED TO OPERATE THE FAN MOTOR. SELECT REPLY CODE 10AB62 AZKCB 10VOLTAGE IN VOLTS,MOTOR,FAN FAN MOTOR VOLTAGE IN VOLTS THE TOTAL ELECTRICAL VOLTAGE OF THE FAN MOTOR,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AZKDG 19NAME ASSIGNED BY CONTROLLING AGENCY,ITEM ITEM NAME ASSIGNED BY CONTROLLING AGENCY THE NAME OF THE ITEM ASSIGNED BY THE CONTROLLING AGENCY. FULL TEXT WRITE-IN 0 AZKEJ 10FREQUENCY RATING,MOTOR,FAN FAN MOTOR FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE FAN MOTOR IS RATED. 2D AND 1B MODE REPLY21AC321AC20 AZKFD 19PHASE,MOTOR,FAN FAN MOTOR PHASE THE NUMBER OF ALTERNATING CURRENT PHASES OF THE FAN MOTOR. SELECT REPLY CODE 10AD02 AZKGD /D/ 09MATERIAL,SEGMENT SEGMENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SEGMENT/S/ IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AZKHD 18TYPE,DRIVE,COMPRESSOR COMPRESSOR DRIVE TYPE INDICATES THE TYPE OF DRIVE FOR WHICH THE COMPRESSOR IS DESIGNED. SELECT REPLY CODE 10AG25 AZKJD 18TYPE,CURRENT,MOTOR MOTOR CURRENT TYPE INDICATES THE TYPE OF CURRENT REQUIRED TO OPERATE THE MOTOR. SELECT REPLY CODE 10AB62 AZKKB 10VOLTAGE IN VOLTS,MOTOR MOTOR VOLTAGE IN VOLTS THE TOTAL ELECTRICAL VOLTAGE OF THE MOTOR,EXPRESSED IN VOLTS. 1B MODE REPLY 0 AZKLJ 10FREQUENCY RATING,MOTOR MOTOR FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE MOTOR IS RATED. 2D AND 1B MODE REPLY21AC321AC20 AZKMD 19PHASE,MOTOR MOTOR PHASE THE NUMBER OF ALTERNATING CURRENT PHASES OF THE MOTOR. SELECT REPLY CODE 10AD02 AZKND /D/ 07FEATURE,CONNECTED,CROSS CROSS CONNECTED FEATURE AN INDICATION OF WHETHER OR NOT A CROSS CONNECTED FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 AZKPB 10HORSEPOWER RATING,BRAKE BRAKE HORSEPOWER RATING THE BRAKE HORSEPOWER FOR WHICH THE ITEM IS RATED. 1B MODE REPLY 0 AZKQJ 10TEMP RATING TEMP RATING A VALUE WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AS APPLIED TO THE OPERATION,OR LIMITATION OF OPERATION,OF AN ITEM. 2D AND 1B MODE REPLY21AB361AC20 AZKRB 10TEMP RATING IN DEG FAHRENHEIT,AMBIENT AMBIENT TEMP RATING IN DEG FAHRENHEIT THE TEMPERATURE OF THE MEDIUM SURROUNDING AN ITEM AT WHICH IT CAN BE OPERATED,EXPRESSED IN DEGREES FAHRENHEIT. 1B MODE REPLY 0 AZKSJ 04DIAMETER,OUTSIDE,OVERALL,SURFACE,BRUSH CONTACTING BRUSH CONTACTING SURFACE OVERALL OUTSIDE DIAMETER THE OVERALL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BRUSH CONTACTING SURFACE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AZKTD /D/ 07SUPPRESSION,INTERFERENCE,RADIO RADIO INTERFERENCE SUPPRESSION AN INDICATION OF WHETHER OR NOT RADIO INTERFERENCE SUPPRESSION IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AZKWG /D/ 19SPEC/STD,SUPPRESSION,RADIO INTERFERENCE RADIO INTERFERENCE SUPPRESSION SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO CONTROL THE NATURE AND DEGREE OF RADIO INTERFERENCE SUPPRESSION. FULL TEXT WRITE-IN 0 AZKXD 11METHOD,DISPENSING DISPENSING METHOD THE DISPENSING METHOD FOR WHICH THE ITEM IS EQUIPPED. SELECT REPLY CODE 10AH83 AZKYD 11METHOD,ATTACHMENT,SHAFT SHAFT ATTACHMENT METHOD THE MEANS USED TO ATTACH THE ITEM TO A SHAFT. SELECT REPLY CODE 10AB47 AZKZD /D/ 07INCLOSURE,CABINET CABINET INCLOSURE AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A CABINET INCLOSURE. SELECT REPLY CODE 10AB22 AZLAD 18TYPE,COMPRESSOR COMPRESSOR TYPE INDICATES THE TYPE OF COMPRESSOR PROVIDED. SELECT REPLY CODE 10AK04 AZLBB 10HORSEPOWER RATING,MOTOR,ELECTRIC,COMPRESSOR COMPRESSOR ELECTRIC MOTOR HORSEPOWER RATING THE RATED HORSEPOWER OF THE COMPRESSOR ELECTRIC MOTOR. 1B MODE REPLY 0 AZLCD /D/ 07HOUSING HOUSING AN INDICATION OF WHETHER OR NOT A HOUSING IS PROVIDED. SELECT REPLY CODE 10AB22 AZLDD /D/ 07MOUNTING,BRACKET,END END BRACKET MOUNTING AN INDICATION OF WHETHER OR NOT AN END BRACKET MOUNTING IS PROVIDED. SELECT REPLY CODE 10AB22 AZLED 19FACILITY FOR WHICH DESIGNED,MOUNTING,END ITEM END ITEM MOUNTING FACILITY FOR WHICH DESIGNED THE MOUNTING FACILITY/IES/ FOR WHICH THE END ITEM IS DESIGNED. SELECT REPLY CODE 10AH21 AZLFD /D/ 07BIN,STORAGE,INTEGRAL INTEGRAL STORAGE BIN AN INDICATION OF WHETHER OR NOT AN INTEGRAL STORAGE BIN IS INCLUDED. SELECT REPLY CODE 10AA49 AZLGD /D/ 07FEATURE,REFRIGERATION REFRIGERATION FEATURE AN INDICATION OF WHETHER OR NOT A REFRIGERATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AZLHJ 10CAPACITY PER 24 HOUR PERIOD,ICE ICE CAPACITY PER 24 HOUR PERIOD THE AMOUNT OF ICE THE ITEM CAN PRODUCE IN A 24 HOUR PERIOD. 1D AND 1B MODE REPLY12AG67 AZLJA 12QUANTITY ACCOMMODATED,CAN,FREEZER TANK FREEZER TANK CAN QUANTITY ACCOMMODATED THE NUMBER OF CANS THE FREEZER TANK WILL ACCOMMODATE. 1A MODE REPLY 0 AZLKJ 04HEIGHT,OUTSIDE,FREEZER TANK FREEZER TANK OUTSIDE HEIGHT THE OUTSIDE MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE FREEZER TANK,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 AZLLJ 04LENGTH,OUTSIDE,FREEZER TANK FREEZER TANK OUTSIDE LENGTH THE OUTSIDE MEASUREMENT OF THE LONGEST DIMENSION OF THE FREEZER TANK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AZLMJ 04WIDTH,OUTSIDE,FREEZER TANK FREEZER TANK OUTSIDE WIDTH THE OUTSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FREEZER TANK,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AZLND /D/ 07SYSTEM,AGITATING,WATER,FREEZING TANK LOW PRESSURE FREEZING TANK LOW PRESSURE WATER AGITATING SYSTEM AN INDICATION OF WHETHER OR NOT A FREEZING TANK LOW PRESSURE WATER AGITATING SYSTEM IS INCLUDED. SELECT REPLY CODE 10AA49 AZLPD /D/ 07AGITATOR,BRINE,FREEZING TANK FREEZING TANK BRINE AGITATOR AN INDICATION OF WHETHER OR NOT A FREEZING TANK BRINE AGITATOR IS INCLUDED. SELECT REPLY CODE 10AA49 AZLQJ 04LENGTH,INSIDE,CAN TOP CAN TOP INSIDE LENGTH THE INSIDE MEASUREMENT OF THE LONGEST DIMENSION OF THE CAN TOP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AZLRJ 04WIDTH,INSIDE,CAN TOP CAN TOP INSIDE WIDTH THE INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CAN TOP,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AZLSJ 04DEPTH,INSIDE,CAN CAN INSIDE DEPTH THE INSIDE MEASUREMENT BETWEEN SPECIFIED POINTS OF A CAN,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AZLTD /D/ 07CONVEYANCE,RESTRICTION,AIR,ICE CAN HIGH PRESSURE ICE CAN HIGH PRESSURE AIR RESTRICTION CONVEYANCE AN INDICATION OF WHETHER OR NOT THE ICE CAN IS PROVIDED WITH A HIGH PRESSURE AIR RESTRICTION CONVEYANCE. SELECT REPLY CODE 10AB22 AZLWD /D/ 07CONDENSER,EVAPORATIVE EVAPORATIVE CONDENSER AN INDICATION OF WHETHER OR NOT AN EVAPORATIVE CONDENSER IS INCLUDED. SELECT REPLY CODE 10AA49 AZLXD /D/ 07TANK,PRECOOLING PRECOOLING TANK AN INDICATION OF WHETHER OR NOT A PRECOOLING TANK(S) IS INCLUDED. SELECT REPLY CODE 10AA49 AZLYD 18TYPE,DESIGN,EVAPORATOR EVAPORATOR DESIGN TYPE INDICATES THE DESIGN TYPE OF THE EVAPORATOR. SELECT REPLY CODE 10AK54 AZLZD /D/ 07CHUTE,ICE,EXTERIOR EXTERIOR ICE CHUTE AN INDICATION OF WHETHER OR NOT AN EXTERIOR ICE CHUTE IS INCLUDED. SELECT REPLY CODE 10AA49 AZMAD /D/ 07CONNECTION,BAG,CANVAS CANVAS BAG CONNECTION AN INDICATION OF WHETHER OR NOT A CANVAS BAG CONNECTION IS PROVIDED. SELECT REPLY CODE 10AB22 AZMBG 19AGENCY,CONTROLLING,FREEZER FREEZER CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE FREEZER. FULL TEXT WRITE-IN 0 AZMCG /D/ 19ADDRESS,AGENCY,CONTROLLING CONTROLLING AGENCY ADDRESS THE ADDRESS OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE ITEM. FULL TEXT WRITE-IN 0 AZMDA 12QUANTITY,CABINET,REFRIGERATING REFRIGERATING CABINET QUANTITY THE NUMBER OF REFRIGERATING CABINETS CONTAINED IN THE ITEM. 1A MODE REPLY 0 AZMED 02DESIGN,COMPARTMENT COMPARTMENT DESIGN THE DESIGN OF THE COMPARTMENT PROVIDED. SELECT REPLY CODE 10AL59 AZMFG 19AGENCY,CONTROLLING,REFRIGERATING CABINET REFRIGERATING CABINET CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE REFRIGERATING CABINET. FULL TEXT WRITE-IN 0 AZMGG /D/ 19ADDRESS,AGENCY,CONTROLLING,REFRIGERATING CABINET REFRIGERATING CABINET CONTROLLING AGENCY ADDRESS THE ADDRESS OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE REFRIGERATING CABINET. FULL TEXT WRITE-IN 0 AZMHG /D/ 19NUMBER,IDENTIFYING,REFRIGERATING CABINET REFRIGERATING CABINET IDENTIFYING NUMBER THE IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE REFRIGERATING CABINET. FULL TEXT WRITE-IN 0 AZMJD 18TYPE,PRESSURE,DISPENSING DISPENSING PRESSURE TYPE INDICATES THE TYPE OF PRESSURE USED IN DISPENSING. SELECT REPLY CODE 10AL77 AZMKG /D/ 19CONFIGURATION,MOUNTING,END ITEM END ITEM MOUNTING CONFIGURATION THE NARRATIVE EXPRESSION USED FOR INDICATING THE CONFIGURATION OF THE END ITEM MOUNTING FACILITIES. PLEASE USE MRC ALGC IN PLACE OF THIS DISCONTINUED MRC. FULL TEXT WRITE-IN 0 AZMLG 04SPACING,FACILITY,END ITEM MOUNTING END ITEM MOUNTING FACILITY SPACING THE SPACING BETWEEN THE END ITEM MOUNTING FACILITIES. FULL TEXT WRITE-IN 0 AZMMD 18TYPE,DISPENSER DISPENSER TYPE INDICATES THE TYPE OF DISPENSER INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AK54 AZMND 18TYPE,DEVICE,DRAW-OFF DRAW-OFF DEVICE TYPE INDICATES THE TYPE OF DEVICE UTILIZED FOR DRAW-OFF. SELECT REPLY CODE 10AH83 AZMPD /D/ 07CABINET,UNIT,REFRIGERATION REFRIGERATION UNIT CABINET AN INDICATION OF WHETHER OR NOT A REFRIGERATION UNIT CABINET IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AZMQD /D/ 07CURRENT,OUTPUT,REGULATED REGULATED OUTPUT CURRENT AN INDICATION OF WHETHER OR NOT A REGULATED OUTPUT CURRENT IS PROVIDED. SELECT REPLY CODE 10AB22 AZMRD /D/ 07OUTPUT,AC,AUXILIARY AUXILIARY AC OUTPUT AN INDICATION OF WHETHER OR NOT AN AUXILIARY ALTERNATING CURRENT OUTPUT IS PROVIDED. SELECT REPLY CODE 10AB22 AZMSD /D/ 09MATERIAL,TOP,CABINET CABINET TOP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CABINET TOP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AZMTD /D/ 09MATERIAL,SIDE,CABINET CABINET SIDE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CABINET SIDE(S) IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AZMWJ /D/ 10CURRENT RATING,AC,OUTPUT OUTPUT AC CURRENT RATING THE OUTPUT ALTERNATING CURRENT RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE. 2D AND 1B MODE REPLY21AC301AC20 AZMXD /D/ 17SURFACE TREATMENT,SIDE,CABINET CABINET SIDE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE CABINET SIDE SURFACES. PLEASE USE MRC SFTT WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AZMYD /D/ 07CURRENT,OUTPUT,AC,REGULATED REGULATED AC OUTPUT CURRENT AN INDICATION OF WHETHER OR NOT A REGULATED ALTERNATING CURRENT OUTPUT IS PROVIDED. SELECT REPLY CODE 10AB22 AZMZD /D/ 07SPACE,STORAGE,CABINET REFRIGERATED CABINET REFRIGERATED STORAGE SPACE AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH REFRIGERATED STORAGE SPACE IN THE CABINET. IF PROVIDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AB22 AZNAD /D/ 09MATERIAL,EXTERIOR,TANK TANK EXTERIOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TANK EXTERIOR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AZNCD /D/ 17SURFACE TREATMENT,EXTERIOR,TANK TANK EXTERIOR SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE EXTERIOR SURFACE OF THE TANK. PLEASE USE MRC SFTT WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AZNED /D/ 09MATERIAL,INTERIOR,TANK TANK INTERIOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TANK INTERIOR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AZNFD /D/ 17SURFACE TREATMENT,INTERIOR,TANK TANK INTERIOR SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE INTERIOR SURFACE OF THE TANK. PLEASE USE MRC SFTT WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 AZNGD 02DESIGN,BAR,ANGLE ANGLE BAR DESIGN THE DESIGN OF THE ANGLE BAR. SELECT REPLY CODE 10AG26 AZNHD /D/ 07SLOTS,SPIKE SPIKE SLOTS AN INDICATION OF WHETHER OR NOT SPIKE SLOTS ARE INCLUDED. SELECT REPLY CODE 10AA49 AZNJJ 04DISTANCE BETWEEN CENTER BOLT HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN CENTER BOLT HOLES THE CENTER TO CENTER DISTANCE BETWEEN THE CENTER BOLT HOLES. 1D AND 1B MODE REPLY11AA05 AZNKJ /D/ 04DISTANCE BETWEEN OTHER BOLT HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN OTHER BOLT HOLES THE CENTER TO CENTER DISTANCE BETWEEN OTHER BOLT HOLES. 1D AND 1B MODE REPLY11AA05 AZNLD /D/ 07CHARACTERISTIC,OVERSIZE OVERSIZE CHARACTERISTIC AN INDICATION OF WHETHER OR NOT AN OVERSIZE CHARACTERISTIC IS INCLUDED. SELECT REPLY CODE 10AA49 AZNMD /D/ 07CORRUGATIONS CORRUGATIONS AN INDICATION OF WHETHER OR NOT CORRUGATIONS ARE INCLUDED. SELECT REPLY CODE 10AA49 AZNND /D/ 07BOLTS-NUTS BOLTS-NUTS AN INDICATION OF WHETHER OR NOT THE ITEM IS FURNISHED WITH BOLTS AND/OR NUTS. SELECT REPLY CODE 10AA55 AZNPD 02DESIGN,SEAT,RAIL RAIL SEAT DESIGN THE DESIGN OF THE RAIL SEAT. SELECT REPLY CODE 10AG26 AZNQD 19CONSTRUCTION,SHOULDER SHOULDER CONSTRUCTION THE STRUCTURAL CHARACTERISTIC(S) OF THE SHOULDER. SELECT REPLY CODE 10AL59 AZNRJ 04LENGTH AT RIGHT ANGLE TO SHOULDER LENGTH AT RIGHT ANGLE TO SHOULDER A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM TAKEN AT RIGHT ANGLE TO THE SHOULDER,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AZNSJ 04WIDTH PARALLEL TO SHOULDER WIDTH PARALLEL TO SHOULDER A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ITEM PARALLEL TO THE SHOULDER,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AZNTD /D/ 07SHAPE,TRAPEZOIDAL TRAPEZOIDAL SHAPE AN INDICATION OF WHETHER OR NOT A TRAPEZOIDAL SHAPE IS INCLUDED. SELECT REPLY CODE 10AA49 AZNWD 02DESIGN,BOTTOM BOTTOM DESIGN THE DESIGN OF THE BOTTOM OF THE ITEM. SELECT REPLY CODE 10AK39 AZNXJ /D/ 04SIZE FOR WHICH PUNCHED,SPIKE SPIKE SIZE FOR WHICH PUNCHED DESIGNATES THE SIZE OF SPIKE/S/ FOR WHICH THE ITEM IS PUNCHED. 1D AND 1B MODE REPLY11AA05 AZNYD /D/ 07HOLE,DRILLED DRILLED HOLE AN INDICATION OF WHETHER OR NOT A DRILLED HOLE IS INCLUDED. SELECT REPLY CODE 10AA49 AZNZJ 04DIAMETER,HOLE HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 AZPAD 08LOCATION,HOLE HOLE LOCATION INDICATES THE LOCATION OF THE HOLE/S/ ON THE ITEM. SELECT REPLY CODE 10AJ91 AZPBJ 04DISTANCE FROM RAIL END,CENTER,FIRST HOLE FIRST HOLE CENTER DISTANCE FROM RAIL END THE DISTANCE FROM THE END OF THE RAIL TO THE CENTER OF THE FIRST HOLE. 2D AND 1B MODE REPLY21AA051AC20 AZPCJ /D/ 04LENGTH LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA052AM01 AZPDD /D/ 07FEATURE,COOLED,CONTROL CONTROL COOLED FEATURE AN INDICATION OF WHETHER OR NOT A CONTROL COOLED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AZPED /D/ 07FEATURE,HARDENED,END END HARDENED FEATURE AN INDICATION OF WHETHER OR NOT AN END HARDENED FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 AZPFD /D/ 07BLADE,OFFSET OFFSET BLADE AN INDICATION OF WHETHER OR NOT AN OFFSET BLADE IS INCLUDED. SELECT REPLY CODE 10AA49 AZPGD /D/ 07BLADE,NOTCHED NOTCHED BLADE AN INDICATION OF WHETHER OR NOT A NOTCHED BLADE IS INCLUDED. SELECT REPLY CODE 10AA49 AZPHD /D/ 07BLADE,WEDGE WEDGE BLADE AN INDICATION OF WHETHER OR NOT A WEDGE BLADE IS INCLUDED. SELECT REPLY CODE 10AA49 AZPJJ 04WIDTH,CUT CUT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CUT,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AZPKJ 04HEIGHT,CUT CUT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE CUT,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 AZPLD /D/ 07BLADE,STRAIGHT,HORIZONTAL HORIZONTAL STRAIGHT BLADE AN INDICATION OF WHETHER OR NOT A HORIZONTAL STRAIGHT BLADE IS INCLUDED. SELECT REPLY CODE 10AA49 AZPMD 07ADJUSTABILITY,ANGLE,CUT CUT ANGLE ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE CUT ANGLE IS ADJUSTABLE. SELECT REPLY CODE 10AB00 AZPNJ 04HEIGHT,BLADE BLADE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BLADE,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 AZPPD /D/ 07FLANGERS FLANGERS AN INDICATION OF WHETHER OR NOT FLANGERS ARE INCLUDED. SELECT REPLY CODE 10AA49 AZPQJ A08LOCATION AND QUANTITY,HOLE HOLE LOCATION AND QUANTITY INDICATES THE LOCATION AND NUMBER OF HOLES ON THE ITEM. 1D AND 1A MODE REPLY13AJ91 AZPRJ 04SPACING,HOLE HOLE SPACING THE SPACING BETWEEN HOLES. 1D AND 1B MODE REPLY11AA05 AZPSJ 04DISTANCE BETWEEN INSIDE HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN INSIDE HOLES THE CENTER TO CENTER DISTANCE BETWEEN THE INSIDE HOLES. 1D AND 1B MODE REPLY11AA05 AZPTD 03DESIGNATION,COMMERCIAL COMMERCIAL DESIGNATION THE COMMERCIAL DESIGNATION BY WHICH THE ITEM IS IDENTIFIED. SELECT REPLY CODE 10AM64 AZPWJ /D/ 04LENGTH FROM HORN TO RADIUS POINT,SHANK,SWIVEL PIN SWIVEL PIN SHANK LENGTH FROM HORN TO RADIUS POINT A MEASUREMENT OF THE SHANK TAKEN FROM THE HORN TO THE RADIUS POINT OF A SWIVEL PIN. 2D AND 1B MODE REPLY21AA051AC20 AZPXG /D/ 04SIZE,CROSS SECTION,SHANK SHANK CROSS SECTION SIZE A MEASUREMENT OF THE SHANK TAKEN AT RIGHT ANGLES TO ITS LENGTH. FULL TEXT WRITE-IN 0 AZPYJ /D/ 04HEIGHT,BUTT BUTT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BUTT,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 AZPZD /D/ 11METHOD FOR WHICH DESIGNED,OPERATION,UNCOUPLING UNCOUPLING OPERATION METHOD FOR WHICH DESIGNED AN INDICATION OF THE UNCOUPLING OPERATION METHOD FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AJ91 AZQAD /D/ 07FEATURE,OPERATION,ROTARY,UNCOUPLING UNCOUPLING ROTARY OPERATION FEATURE AN INDICATION OF WHETHER OR NOT AN UNCOUPLING ROTARY OPERATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AZQBD /D/ 02DESIGN,OPERATION,SIDE,UNCOUPLING UNCOUPLING SIDE OPERATION DESIGN THE DESIGN OF THE UNCOUPLING PROVIDED FOR SIDE OPERATION. SELECT REPLY CODE 10AL59 AZQCL 16STYLE ACCOMMODATED,BASE,LAMP LAMP BASE STYLE ACCOMMODATED THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE LAMP BASE THE ITEM IS DESIGNED TO ACCOMMODATE. 1L MODE REPLY 0 AZQDA 12QUANTITY,CONNECTOR,IDENTICAL END IDENTICAL END CONNECTOR QUANTITY THE NUMBER OF IDENTICAL END CONNECTORS ON THE ITEM. 1A MODE REPLY 0 AZQED 19POSITION,CONTACT,TWO FLAT TWO FLAT CONTACT POSITION A DESIGNATION THAT DESCRIBES THE BASIC ELECTRICAL CONFIGURATION OF THE TWO FLAT CONTACTS ARRANGEMENT. SELECT REPLY CODE 10AD19 AZQFD /D/ 07ACCOMMODATION,FUSE FUSE ACCOMMODATION AN INDICATION OF WHETHER OR NOT A FUSE ACCOMMODATION IS INCLUDED. SELECT REPLY CODE 10AA49 AZQGD /D/ 07FUSE FUSE AN INDICATION OF WHETHER OR NOT A FUSE IS INCLUDED. SELECT REPLY CODE 10AA49 AZQHB 10WATTAGE RATING IN WATTS,MAXIMUM MAXIMUM WATTAGE RATING IN WATTS THE MAXIMUM RATED POWER THAT AN ITEM CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS. 1B MODE REPLY 0 AZQJD /D/ 07OUTLET,WIRE,SIDE SIDE WIRE OUTLET AN INDICATION OF WHETHER OR NOT A SIDE WIRE OUTLET IS INCLUDED. SELECT REPLY CODE 10AA49 AZQKJ 10WEIGHT WEIGHT A RELATIVE MEASUREMENT OF THE MASS OF AN ITEM WITH RESPECT TO ITS DENSITY. 2D AND 1B MODE REPLY22AG671AC20 AZQNJ /D/ 04THICKNESS,STOCK STOCK THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE MATERIAL STOCK FROM WHICH THE ITEM IS FABRICATED,IN DISTINCTION FROM LENGTH OR WIDTH. 3D AND 1B MODE REPLY31AA051AC201AA13 AZQPJ 04LENGTH,SHOE SHOE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SHOE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AZQQD /D/ 07FEATURE,TWISTED TWISTED FEATURE AN INDICATION OF WHETHER OR NOT A TWISTED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AZQRD /D/ 11METHOD,TWISTING TWISTING METHOD THE MEANS USED TO TWIST THE ITEM. SELECT REPLY CODE 10AF75 AZQSD 03DESIGNATION,STEEL STEEL DESIGNATION THE TERM BY WHICH THE STEEL IS KNOWN OR DESIGNATED. SELECT REPLY CODE 10AM70 AZQTG /D/ 19PROVISION,HANDLING HANDLING PROVISION THE HANDLING FACILITY/IES/ OR ATTACHMENT/S/ PROVIDED ON THE ITEM FOR LIFTING OR REMOVAL. FULL TEXT WRITE-IN 0 AZQWD 08LOCATION,MARKING,SPECIAL SPECIAL MARKING LOCATION INDICATES THE LOCATION ON THE ITEM WHERE SPECIAL MARKINGS ARE FOUND. SELECT REPLY CODE 10AJ91 AZQXD /D/ 07FEATURE,WOVEN,TEXTILE TEXTILE WOVEN FEATURE AN INDICATION OF WHETHER OR NOT A TEXTILE WOVEN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AZQYA 12QUANTITY,ROW,PILE PILE ROW QUANTITY THE NUMBER OF PILE ROWS INCLUDED. 1A MODE REPLY 0 AZQZA 12QUANTITY,SPACE SPACE QUANTITY THE NUMBER OF SPACES INCLUDED. 1A MODE REPLY 0 AZRAJ 04DISTANCE,PILE TO FABRIC OUTER EDGE PILE TO FABRIC OUTER EDGE DISTANCE THE DISTANCE BETWEEN THE PILE AND THE OUTER EDGE OF THE FABRIC. 2D AND 1B MODE REPLY21AA051AC20 AZRBJ 04WIDTH,PILE,OUTER OUTER PILE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE OUTER PILE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AZRCJ 04DISTANCE,CENTER PILE TO OUTER PILE CENTER PILE TO OUTER PILE DISTANCE THE DISTANCE FROM THE CENTER PILE TO THE OUTER PILE. 2D AND 1B MODE REPLY21AA051AC20 AZRDJ 04WIDTH,PILE,CENTER CENTER PILE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CENTER PILE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AZRED 19CONDITION,CELL CELL CONDITION AN INDICATION OF THE STRUCTURE OF THE CELLS MAKING UP THE CELLULAR CORE. SELECT REPLY CODE 10AA62 AZRFG /D/ 19SPEC/STD,MATERIAL,FACE FACE MATERIAL SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE FACE MATERIAL. FULL TEXT WRITE-IN 0 AZRGJ 04THICKNESS,FACE FACE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE FACE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AZRHD /D/ 07FEATURE,LAMINATION LAMINATION FEATURE AN INDICATION OF THE LAMINATION FEATURE OF THE ITEM. SELECT REPLY CODE 10AM71 AZRJG /D/ 04SIZE,CELL CELL SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE CELL. FULL TEXT WRITE-IN 0 AZRKA 12QUANTITY,SWITCH SWITCH QUANTITY THE NUMBER OF SWITCHES PROVIDED. 1A MODE REPLY 0 AZRLJ /D/ 19LEGEND Q LEGEND Q NONE. 2D AND 1B MODE REPLY21AA051AC20 AZRMJ /D/ 19LEGEND U LEGEND U NONE. 2D AND 1B MODE REPLY21AA051AC20 AZRNJ /D/ 19LEGEND V LEGEND V NONE. 2D AND 1B MODE REPLY21AA051AC20 AZRPJ /D/ 19LEGEND Z LEGEND Z NONE. 2D AND 1B MODE REPLY21AA051AC20 AZRQD /D/ 07PERFORATION,CELL CELL PERFORATION AN INDICATION OF WHETHER OR NOT A CELL PERFORATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AZRRJ 10DENSITY RATING,NOMINAL NOMINAL DENSITY RATING A MEASUREMENT OF THE AVERAGE DENSITY PER UNIT VOLUME. 1D AND 1B MODE REPLY12AG67 AZRSJ 10DENSITY RATING,MAXIMUM MAXIMUM DENSITY RATING A MEASUREMENT OF THE MAXIMUM DENSITY PER UNIT VOLUME. 1D AND 1B MODE REPLY12AG67 AZRTJ 10LIMIT,TEMP,MAXIMUM SERVICE MAXIMUM SERVICE TEMP LIMIT THE MAXIMUM VALUE WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AS APPLIED TO THE SERVICE. 1D AND 1B MODE REPLY13AJ40 AZRWJ /D/A13THREAD QUANTITY THREAD QUANTITY THE NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. PLEASE USE MRC CQRN IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1A MODE REPLY13AJ40 AZRXJ 04DEPTH,CELL CELL DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON A CELL,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AZRYD /D/ 19PROVISION,MOUNTING,TANK TANK MOUNTING PROVISION AN INDICATION OF THE MEANS PROVIDED FOR MOUNTING THE TANK. SELECT REPLY CODE 10AB21 AZRZD /D/ 07FACILITY,INSTALLATION,SHIPBOARD SHIPBOARD INSTALLATION FACILITY AN INDICATION OF WHETHER OR NOT A SHIPBOARD INSTALLATION FACILITY IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 AZSAA 12QUANTITY,SOURCE,HEAT HEAT SOURCE QUANTITY THE NUMBER OF HEAT SOURCES USED IN THE ITEM. 1A MODE REPLY 0 AZSBD /D/ 09MATERIAL,CABINET CABINET MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CABINET IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AZSCD 03DESIGNATION,REPLACEMENT REPLACEMENT DESIGNATION THE DESIGNATION BY WHICH THE REPLACEMENT IS IDENTIFIED. SELECT REPLY CODE 10AH21 AZSDD 18TYPE,UNIT,COMPRESSOR COMPRESSOR UNIT TYPE INDICATES THE TYPE OF COMPRESSOR UNIT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 AZSEB 10CAPACITY IN BTU PER HOUR,COOLING,NOMINAL NOMINAL COOLING CAPACITY IN BTU PER HOUR THE NOMINAL CAPACITY OF THE ITEM TO COOL,EXPRESSED IN BRITISH THERMAL UNITS PER HOUR. 1B MODE REPLY 0 AZSFJ 10CAPACITY,COOLING,NOMINAL NOMINAL COOLING CAPACITY THE NOMINAL CAPACITY OF THE ITEM TO COOL. 1D AND 1B MODE REPLY11AC64 AZSGB /D/ 10CAPACITY IN BTU PER HOUR,HEATING,NOMINAL NOMINAL HEATING CAPACITY IN BTU PER HOUR THE NOMINAL CAPACITY OF THE ITEM TO HEAT,EXPRESSED IN BRITISH THERMAL UNITS PER HOUR. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1B MODE REPLY 0 AZSHJ 10CAPACITY,HEATING,NOMINAL NOMINAL HEATING CAPACITY THE NOMINAL CAPACITY OF THE ITEM TO HEAT. 1D AND 1B MODE REPLY11AC64 AZSJD /D/ 07ACCESSORIES ACCESSORIES AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH ACCESSORIES. SELECT REPLY CODE 10AB22 AZSKD /D/ 07CURRENT,REGULATED REGULATED CURRENT AN INDICATION OF WHETHER OR NOT A REGULATED CURRENT IS PROVIDED. SELECT REPLY CODE 10AB22 AZSLJ 10CURRENT RATING,INPUT INPUT CURRENT RATING THE AMOUNT OF INPUT CURRENT FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY21AC301AC20 AZSMD /D/ 07FILTER,FREQUENCY,RADIO RADIO FREQUENCY FILTER AN INDICATION OF WHETHER OR NOT A RADIO FREQUENCY FILTER IS PROVIDED. SELECT REPLY CODE 10AB22 AZSNJ 04DIAMETER,BULLS-EYE BULLS-EYE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR BULLS-EYE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AZSPJ 04WIDTH,OVERALL,SILHOUETTED IMAGE SILHOUETTED IMAGE OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A SILHOUETTED IMAGE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AZSQJ 04HEIGHT,OVERALL,SILHOUETTED IMAGE SILHOUETTED IMAGE OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF A SILHOUETTED IMAGE. 2D AND 1B MODE REPLY21AA051AC20 AZSRD 18TYPE,CAPACITY,DESICCANT DESICCANT CAPACITY TYPE INDICATES THE TYPE OF DESICCANT CAPACITY PROVIDED FOR THE ITEM. SELECT REPLY CODE 10AM69 AZSSH 01COLOR AND LOCATION,FACE FACE COLOR AND LOCATION THE HUE OR TINT OF THE FACE AND ITS LOCATION ON THE ITEM. 2D MODE REPLY 26AD063AJ91 AZSTA 12QUANTITY,CONTAINER,DESICCANT DESICCANT CONTAINER QUANTITY THE NUMBER OF DESICCANT CONTAINERS PROVIDED. 1A MODE REPLY 0 AZSWJ 10CAPACITY,CONTAINER,DESICCANT DESICCANT CONTAINER CAPACITY THE AMOUNT OF LIQUID,GRANULES,AND THE LIKE,THE CONTAINER WILL HOLD. 1D AND 1B MODE REPLY12AG67 AZSXJ 10CAPACITY,BULK BULK CAPACITY THE AMOUNT OF LIQUID,GRANULES,OR THE LIKE,OF BULK MATERIAL THE ITEM WILL HOLD. 1D AND 1B MODE REPLY12AG67 AZSYG /D/ 19CONFIGURATION,HOLE,MOUNTING MOUNTING HOLE CONFIGURATION THE NARRATIVE EXPRESSION USED FOR INDICATING THE CONFIGURATION OF THE MOUNTING HOLES. FULL TEXT WRITE-IN 0 AZSZD 18TYPE,DESICCANT DESICCANT TYPE INDICATES THE TYPE OF DRYING AGENT USED IN THE ITEM. SELECT REPLY CODE 10AL79 AZTAD 19POSITION,RAIL,TARGET FRAME TARGET FRAME RAIL POSITION THE POSITION OF THE RAIL IN RELATIONSHIP TO THE TARGET FRAME. SELECT REPLY CODE 10AF63 AZTBA 12QUANTITY,BED,DESICCANT DESICCANT BED QUANTITY THE NUMBER OF DESICCANT BEDS PROVIDED. 1A MODE REPLY 0 AZTCJ 10DELIVERY,AIR,DEHUMIDIFIED DEHUMIDIFIED AIR DELIVERY THE AMOUNT OF DEHUMIDIFIED AIR DELIVERED BY THE ITEM. 2D AND 1B MODE REPLY22AB491AC20 AZTDJ 10PRESSURE,DELIVERY,DEHUMIDIFIED AIR DEHUMIDIFIED AIR DELIVERY PRESSURE THE PRESSURE OF DEHUMIDIFIED AIR DELIVERED BY THE ITEM. 2D AND 1B MODE REPLY22AG201AC20 AZTEJ 10DELIVERY,AIR,REACTIVATED REACTIVATED AIR DELIVERY THE AMOUNT OF REACTIVATED AIR DELIVERED BY THE ITEM. 2D AND 1B MODE REPLY22AB491AC20 AZTFJ 10PRESSURE,DELIVERY,REACTIVATED AIR REACTIVATED AIR DELIVERY PRESSURE THE PRESSURE OF THE REACTIVATED AIR DELIVERED BY THE ITEM. 2D AND 1B MODE REPLY22AG201AC20 AZTGJ 10WEIGHT REMOVED PER OPERATIONAL HOUR,WATER WATER WEIGHT REMOVED PER OPERATIONAL HOUR THE AMOUNT OF WATER REMOVED BY THE ITEM EACH HOUR OF OPERATION,EXPRESSED BY WEIGHT. 1D AND 1B MODE REPLY12AG67 AZTHB /D/ 10TEMP IN DEG FAHRENHEIT,INPUT INPUT TEMP IN DEG FAHRENHEIT THE INPUT TEMPERATURE OF THE ITEM,EXPRESSED IN DEGREES FAHRENHEIT. 1B MODE REPLY 0 AZTJB 10HUMIDITY IN PERCENT,RELATIVE,INPUT INPUT RELATIVE HUMIDITY IN PERCENT THE INPUT RELATIVE HUMIDITY OF THE ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 AZTKJ 04HEIGHT,OVERALL,BODY BODY OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE BODY. 2D AND 1B MODE REPLY21AA051AC20 AZTLJ 04LENGTH,OVERALL,BODY BODY OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BODY. 2D AND 1B MODE REPLY21AA051AC20 AZTMJ 04WIDTH,OVERALL,BODY BODY OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BODY,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AZTNJ 04DIAMETER,OVERALL,BODY BODY OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF A BODY. 2D AND 1B MODE REPLY21AA051AC20 AZTPD /D/ 07TUBE,DISPERSION DISPERSION TUBE AN INDICATION OF WHETHER OR NOT A DISPERSION TUBE IS INCLUDED. SELECT REPLY CODE 10AA49 AZTQD 18TYPE FOR WHICH DESIGNED,LINE LINE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF LINE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK31 AZTRJ 04WIDTH,LOOP,LARGEST LARGEST LOOP WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AZTSJ 04WIDTH,LOOP,SMALLEST SMALLEST LOOP WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AZTTJ /D/ 04THICKNESS,PERIPHERY PERIPHERY THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AZTWJ /D/ 04THICKNESS,TONGUE,LOWER LOWER TONGUE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AZTXJ /D/ 04THICKNESS,TONGUE,UPPER UPPER TONGUE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 AZTYJ /D/ 04DIAMETER,HOLE,BRACKET BRACKET HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AZTZJ /D/ 04DISTANCE BETWEEN BRACKET HOLE CENTERS DISTANCE BETWEEN BRACKET HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWAJ 04WIDTH,SHANK,PRONG PRONG SHANK WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWBJ 04DISTANCE BETWEEN LOOP AND PRONG,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN LOOP AND PRONG NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWCJ 04RADIUS,LOOP LOOP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWDJ 04WIDTH,OPENING,LOOP LOOP OPENING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE LOOP OPENING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AZWEJ 04DISTANCE FROM LOOP CENTER TO END DISTANCE FROM LOOP CENTER TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWFJ 04DISTANCE FROM END TO HOLE NEAREST LOOP DISTANCE FROM END TO HOLE NEAREST LOOP NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWGJ 04DISTANCE FROM BASE TO LIP DISTANCE FROM BASE TO LIP NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWHJ 04DISTANCE FROM END TO NEAREST BEND DISTANCE FROM END TO NEAREST BEND NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWJJ 04DISTANCE FROM LOOP TO MOUNTING TAB DISTANCE FROM LOOP TO MOUNTING TAB NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWKJ 04DISTANCE BETWEEN LOOPS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN LOOPS NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWLJ /D/ 04DISTANCE,CENTER TO MOUNTING HOLE CENTER TO MOUNTING HOLE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWMJ /D/ 04DISTANCE,TAB,MOUNTING MOUNTING TAB DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWNJ 04LENGTH,LEG,LOCK LOCK LEG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE LOCK LEG,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 AZWPJ 04WIDTH,LEG,LOCK LOCK LEG WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE LOCK LEG,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AZWQJ /D/ 04DISTANCE FROM CENTER,HOLE HOLE DISTANCE FROM CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWRJ /D/ 04HEIGHT,LEG,LOCK LOCK LEG HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWSJ 04DISTANCE FROM EDGE TO HOLE CENTER,HORIZONTAL HORIZONTAL DISTANCE FROM EDGE TO HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWTJ 04DISTANCE FROM EDGE TO HOLE CENTER,VERTICAL VERTICAL DISTANCE FROM EDGE TO HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWWJ /D/ 04RADIUS,LEG,LOCK LOCK LEG RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWXJ /D/ 04WIDTH,ACCOMMODATION,BEAM BEAM ACCOMMODATION WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWYJ /D/ 04DISTANCE,HALF,CLAMP CLAMP HALF DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 AZWZJ /D/ 04DIAMETER,CLOSED CLOSED DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 AZXAD /D/ 07CUSHION,WEDGED WEDGED CUSHION AN INDICATION OF WHETHER OR NOT A WEDGED CUSHION IS INCLUDED. SELECT REPLY CODE 10AA49 AZXBD /D/ 18TYPE,NUT,INTEGRAL INTEGRAL NUT TYPE INDICATES THE TYPE OF INTEGRAL NUT PROVIDED. SELECT REPLY CODE 10AH33 AZXCA 12QUANTITY,NUT NUT QUANTITY THE NUMBER OF NUTS PROVIDED. 1A MODE REPLY 0 AZXDD /D/ 08LOCATION,NUT NUT LOCATION INDICATES THE LOCATION OF THE NUT ON THE ITEM. SELECT REPLY CODE 10AJ91 AZXED /D/ 07NUT,REMOVABLE REMOVABLE NUT AN INDICATION OF WHETHER OR NOT A REMOVABLE NUT IS INCLUDED. SELECT REPLY CODE 10AA49 AZXFJ 04DIAMETER ACCOMMODATED,SHANK SHANK DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE SHANK,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AZXGJ 10SIZE FOR WHICH DESIGNED,HOLE,PANEL PANEL HOLE SIZE FOR WHICH DESIGNED DESIGNATES THE PANEL HOLE SIZE FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 AZXHJ /D/ 04SIZE ACCOMMODATED,CASE,INSTRUMENT INSTRUMENT CASE SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE INSTRUMENT CASE THE ITEM WILL ACCOMMODATE. 2D AND 1B MODE REPLY21AA051AC20 AZXJA /D/ 12QUANTITY,HOLE,MOUNTING BRACKET MOUNTING BRACKET HOLE QUANTITY THE NUMBER OF HOLES PROVIDED IN THE BRACKET TO FACILITATE MOUNTING TO ANOTHER ITEM. 1A MODE REPLY 0 AZXKJ /D/A13THREAD CLASS AND LOCATION THREAD CLASS AND LOCATION A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE OF AN EXTERNAL OR INTERNAL THREAD,AND ITS LOCATION. 1D AND 1A MODE REPLY13AJ91 AZXLJ /D/T13THREAD PITCH DIAMETERS AND LOCATION THREAD PITCH DIAMETERS AND LOCATION THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD,AND ITS LOCATION. 2D AND 1F MODE REPLY21AA053AJ91 AZXMD /D/ 09MATERIAL,KNUCKLE KNUCKLE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE KNUCKLE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AZXND /D/ 09MATERIAL,LOCK LOCK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LOCK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 AZXPD /D/ 02DESIGN,MOUNTING,STRUT STRUT MOUNTING DESIGN THE DESIGN OF THE STRUT MOUNTING PROVIDED. SELECT REPLY CODE 10AA38 AZXQD /D/ 19CONSTRUCTION,TRUSS TRUSS CONSTRUCTION THE STRUCTURAL CHARACTERISTIC(S) OF THE TRUSS. SELECT REPLY CODE 10AL59 AZXRD /D/ 14SHAPE,CROSS-SECTIONAL,MEMBER,COMPRESSION COMPRESSION MEMBER CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE COMPRESSION MEMBER WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 AZXSD /D/ 14SHAPE,CROSS-SECTIONAL,TENSION MEMBER TENSION MEMBER CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE TENSION MEMBER WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 AZXTJ /D/A18TYPE AND QUANTITY,CLASP CLASP TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF CLASPS PROVIDED. 1D AND 1A MODE REPLY13AK54 AZXWJ /D/ 04DISTANCE FROM BEAM CENTERLINE TO FULCRUM/DOUBLE JAW CENTER DISTANCE FROM BEAM CENTERLINE TO FULCRUM/DOUBLE JAW CENTER THE DISTANCE FROM THE BEAM CENTERLINE TO THE CENTER OF THE FULCRUM OR DOUBLE JAW. 1D AND 1B MODE REPLY11AA05 AZXXD /D/ 18TYPE,HEAD,BRAKE BRAKE HEAD TYPE INDICATES THE TYPE OF BRAKE HEAD PROVIDED. SELECT REPLY CODE 10AK54 AZXYD /D/ 19POSITION,HANGING HANGING POSITION THE POSITION IN WHICH THE ITEM IS DESIGNED TO HANG. SELECT REPLY CODE 10AJ91 AZXZD /D/ 07CROSS SECTION,SHAPED,PEAR,HANGER END HANGER END PEAR SHAPED CROSS SECTION AN INDICATION OF WHETHER OR NOT A PEAR SHAPED CROSS SECTION AT THE HANGER END IS INCLUDED. SELECT REPLY CODE 10AA49 AZYAA 19CODE,MANUFACTURER MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE ITEM. 1A MODE REPLY 0 AZYBG /D/ 19NUMBER FOR WHICH DESIGNED,MODEL,GUN GUN MODEL NUMBER FOR WHICH DESIGNED THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE GUN FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 AZYCG /D/ 19NUMBER FOR WHICH DESIGNED,MODEL,SMALL ARMS/TELESCOPE SMALL ARMS/TELESCOPE MODEL NUMBER FOR WHICH DESIGNED THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE SMALL ARMS/TELESCOPE FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 AZYDG /D/ 19DOCUMENT,COMPONENTS/ACCESSORIES,MAJOR,GOVERNMENT AGENCY CONTROLLING GOVERNMENT AGENCY CONTROLLING MAJOR COMPONENTS/ACCESSORIES DOCUMENT THE NAME OF THE GOVERNMENT AGENCY WHICH CONTROLS THE MAJOR COMPONENTS AND/OR ACCESSORIES DOCUMENT. FULL TEXT WRITE-IN 0 AZYEG /D/ 19TITLE,SERIES,GOVERNMENT MAJOR COMPONENTS/ACCESSORIES DOCUMENT GOVERNMENT MAJOR COMPONENTS/ACCESSORIES DOCUMENT SERIES TITLE THE NAME OR SERIES TITLE OF THE GOVERNMENT MAJOR COMPONENTS AND/OR ACCESSORIES DOCUMENT. FULL TEXT WRITE-IN 0 AZYFG /D/ 03DESIGNATOR,DOCUMENT,GOVERNMENT MAJOR COMPONENTS/ACCESSORIES GOVERNMENT MAJOR COMPONENTS/ACCESSORIES DOCUMENT DESIGNATOR THE ASSIGNED NUMBER AND/OR SYMBOL USED TO IDENTIFY THE GOVERNMENT MAJOR COMPONENTS AND/OR ACCESSORIES DOCUMENT DESIGNATOR. FULL TEXT WRITE-IN 0 AZYGA /D/ 19NUMBER,PAGE,GOVERNMENT MAJOR COMPONENTS/ACCESSORIES DOCUMENT GOVERNMENT MAJOR COMPONENTS/ACCESSORIES DOCUMENT PAGE NUMBER THE PAGE NUMBER OR OTHER DESIGNATION ASSIGNED BY THE GOVERNMENT AGENCY INDICATING THE MAJOR COMPONENTS AND/OR ACCESSORIES LISTING IN THE DOCUMENT. 1A MODE REPLY 0 AZYHG /D/ 19NUMBER,IDENTIFYING,COMPONENT COMPONENT IDENTIFYING NUMBER THE IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE COMPONENT. FULL TEXT WRITE-IN 0 AZYJD /D/ 07BIT,MOUTHPIECE MOUTHPIECE BIT AN INDICATION OF WHETHER OR NOT A MOUTHPIECE BIT/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 AZYKD 18TYPE,BOCAL BOCAL TYPE INDICATES THE TYPE OF BOCAL PROVIDED. SELECT REPLY CODE 10AM13 AZYLD 19ARRANGEMENT,KEY KEY ARRANGEMENT THE ARRANGEMENT OF THE KEY/S/ ON THE ITEM. SELECT REPLY CODE 10AJ50 AZYMD /D/ 07REST,HAND HAND REST AN INDICATION OF WHETHER OR NOT A HAND REST IS PROVIDED. SELECT REPLY CODE 10AB22 AZYND 02DESIGN,HOLE,TONE TONE HOLE DESIGN THE DESIGN OF THE TONE HOLE PROVIDED ON THE ITEM. SELECT REPLY CODE 10AK54 AZYPJ /D/ 19FLY FLY NONE. 1D AND 1B MODE REPLY11AA05 AZYQJ /D/ 19HOIST HOIST NONE. 1D AND 1B MODE REPLY11AA05 AZYRH 19MATERIAL AND TYPE ACCOMMODATED,PROJECTION PROJECTION MATERIAL AND TYPE ACCOMMODATED THE PROJECTION MATERIAL THE ITEM IS DESIGNED TO ACCOMMODATE,AND ITS TYPE. 2D MODE REPLY 22AG372AM80 AZYSJ 04WIDTH,MATERIAL MATERIAL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MATERIAL,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 AZYTJ 04LENGTH,MATERIAL,PROJECTION PROJECTION MATERIAL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE PROJECTION MATERIAL,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 AZYWD 18TYPE,TRACK,SOUND SOUND TRACK TYPE INDICATES THE TYPE OF SOUND TRACK PROVIDED ON THE ITEM. SELECT REPLY CODE 10AM04 AZYXJ 10CAPACITY,REEL REEL CAPACITY THE AMOUNT OF MATERIAL THE REEL WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 AZYYD 18TYPE,LAMP,PROJECTION PROJECTION LAMP TYPE INDICATES THE TYPE OF PROJECTION LAMP THAT PROVIDES ILLUMINATION. SELECT REPLY CODE 10AD48 AZYZB /D/ 04SIZE,APERTURE,LENS LENS APERTURE SIZE DESIGNATES THE SIZE OF THE LENS OPENING THROUGH WHICH THE LIGHT PASSES. 1B MODE REPLY 0 AZZAA 10CAPACITY,MAGAZINE MAGAZINE CAPACITY THE CAPACITY OF THE MAGAZINE. 1A MODE REPLY 0 AZZBD 08LOCATION,AMPLIFIER AMPLIFIER LOCATION INDICATES THE LOCATION OF THE AMPLIFIER ON THE ITEM. SELECT REPLY CODE 10AJ91 AZZCD 08LOCATION,SPEAKER SPEAKER LOCATION INDICATES THE LOCATION OF THE SPEAKER ON THE ITEM. SELECT REPLY CODE 10AJ91 AZZDD 19USAGE,CURRENT,ALTERNATING ALTERNATING CURRENT USAGE AN INDICATION OF THE ALTERNATING CURRENT USAGE BY THE ITEM. SELECT REPLY CODE 10AM62 AZZED 19USAGE,CURRENT,DIRECT DIRECT CURRENT USAGE AN INDICATION OF THE DIRECT CURRENT USAGE BY THE ITEM. SELECT REPLY CODE 10AM62 AZZFD 19USAGE,BATTERY BATTERY USAGE AN INDICATION OF THE BATTERY USAGE OF THE ITEM. SELECT REPLY CODE 10AM62 AZZGH 11METHOD,OPERATING AND INSERTION,SLIDE SLIDE OPERATING AND INSERTION METHOD THE MEANS USED TO ESTABLISH THE OPERATING FORCE,COMPATIBLE TO THE PARTICULAR SLIDE INSERTION METHOD EMPLOYED. 2D MODE REPLY 24AC582AG37 AZZHD /D/ 19SOURCE FOR WHICH DESIGNED,HEAT HEAT SOURCE FOR WHICH DESIGNED THE HEAT SOURCE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 AZZJD /D/ 07SOURCE,HEAT HEAT SOURCE AN INDICATION OF WHETHER OR NOT A HEAT SOURCE IS INCLUDED. SELECT REPLY CODE 10AA49 AZZKD /D/ 07FEATURE,WIRED WIRED FEATURE AN INDICATION OF WHETHER OR NOT A WIRED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 AZZLD 18TYPE,JOINT,CONNECTING CONNECTING JOINT TYPE INDICATES THE TYPE OF CONNECTING JOINT USED WITH THE ITEM. SELECT REPLY CODE 10AB76 AZZMJ 04DISTANCE FROM OUTLET CENTERLINE TO INLET FACE DISTANCE FROM OUTLET CENTERLINE TO INLET FACE THE DISTANCE FROM THE CENTERLINE OF THE OUTLET TO THE FACE OF THE INLET. 2D AND 1B MODE REPLY21AA051AC20 AZZNJ 10CAPACITY,DESICCANT DESICCANT CAPACITY THE AMOUNT OF LIQUID,GRANULES,AND THE LIKE,THE ITEM WILL HOLD. 1D AND 1B MODE REPLY12AG67 AZZPJ 04LENGTH,OVERALL,CONNECTING JOINT CONNECTING JOINT OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CONNECTING JOINT. 2D AND 1B MODE REPLY21AA051AC20 AZZQJ 04WIDTH,OVERALL,CONNECTING JOINT CONNECTING JOINT OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CONNECTING JOINT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 AZZRB /D/ 10HORSEPOWER RATING,COMPRESSOR COMPRESSOR HORSEPOWER RATING THE RATED HORSEPOWER OF THE COMPRESSOR. 1B MODE REPLY 0 AZZSJ 04DEPTH,OVERALL,JOINT,CONNECTING CONNECTING JOINT OVERALL DEPTH AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF THE CONNECTING JOINT,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 AZZTJ 04DIAMETER,SHELL SHELL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SHELL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 AZZWJ /D/ 04DISTANCE,CENTER TO CENTER,MORTISE MORTISE CENTER TO CENTER DISTANCE THE DISTANCE BETWEEN THE CENTER OF ONE MORTISE AND THE CENTER OF THE ADJACENT MORTISE. 2D AND 1B MODE REPLY21AA051AC20 AZZXG /D/ 04DISTANCE,MORTISE CENTER TO RAIL END MORTISE CENTER TO RAIL END DISTANCE THE DISTANCE FROM THE CENTER OF THE MORTISE TO THE RAIL END. FULL TEXT WRITE-IN 0 AZZYJ 04DISTANCE FOR WHICH DESIGNED DISTANCE FOR WHICH DESIGNED THE DESIGNATED DISTANCE FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AA05 AZZZA 12QUANTITY,BULLS-EYE BULLS-EYE QUANTITY THE NUMBER OF BULLS-EYES INCLUDED ON THE ITEM. 1A MODE REPLY 0 BARBD /D/ 18TYPE,BARB BARB TYPE THE TYPE OF BARB INCLUDED ON AN ITEM. SELECT REPLY CODE 10AD07 BBBBA 12QUANTITY,RING,CONCENTRIC,BULLS-EYE BULLS-EYE CONCENTRIC RING QUANTITY THE NUMBER OF CONCENTRIC RING(S) AROUND THE BULLS-EYE. 1A MODE REPLY 0 BBBCA 03DESIGNATOR,RING,CONCENTRIC CONCENTRIC RING DESIGNATOR THE NUMERIC DESIGNATION OF THE CONCENTRIC RING(S). 1A MODE REPLY 0 BBBDJ /D/A19SPEC/STD,FLUID FLUID SPEC/STD THE SPECIFICATION OR STANDARD /GOVERNMENTAL OR INDUSTRIAL/ THAT SPECIFICALLY COVERS THE TYPE OF FLUID TO BE UTILIZED. 1D AND 1A MODE REPLY11AC28 BBBFJ 04DISTANCE BETWEEN FIRST AND SECOND QUARTERED CIRCLE CENTERS,HORIZONTAL HORIZONTAL DISTANCE BETWEEN FIRST AND SECOND QUARTERED CIRCLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BBBGJ 04DISTANCE BETWEEN SECOND AND THIRD QUARTERED CIRCLE CENTERS,HORIZONTAL HORIZONTAL DISTANCE BETWEEN SECOND AND THIRD QUARTERED CIRCLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BBBHJ /D/ 04DISTANCE BETWEEN THIRD AND FOURTH QUARTERED CIRCLE CENTERS,HORIZONTAL HORIZONTAL DISTANCE BETWEEN THIRD AND FOURTH QUARTERED CIRCLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BBBJJ /D/ 04DISTANCE BETWEEN CENTERLINE AND QUARTERED CIRCLE CENTERS,HORIZONTAL HORIZONTAL DISTANCE BETWEEN CENTERLINE AND QUARTERED CIRCLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BBBKD /D/ 03DESIGNATION,SIZE,FIRST END KEY FIRST END KEY SIZE DESIGNATION A NUMBER OR LETTER REPRESENTING THE SIZE OF A KEY. SELECT REPLY CODE 10AB70 BBBLJ 04DISTANCE BETWEEN FIRST AND SECOND QUARTERED CIRCLE CENTERS,VERTICAL VERTICAL DISTANCE BETWEEN FIRST AND SECOND QUARTERED CIRCLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BBBMJ 04DISTANCE BETWEEN SECOND AND THIRD QUARTERED CIRCLE CENTERS,VERTICAL VERTICAL DISTANCE BETWEEN SECOND AND THIRD QUARTERED CIRCLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BBBNJ 04DISTANCE BETWEEN THIRD AND FOURTH QUARTERED CIRCLE CENTERS,VERTICAL VERTICAL DISTANCE BETWEEN THIRD AND FOURTH QUARTERED CIRCLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BBBPD /D/ 03DESIGNATION,SIZE,SECOND END KEY SECOND END KEY SIZE DESIGNATION A NUMBER OR LETTER REPRESENTING THE SIZE OF A KEY. SELECT REPLY CODE 10AB70 BBBQJ /D/ 04DISTANCE BETWEEN FOURTH AND FIFTH QUARTERED CIRCLE CENTERS,VERTICAL VERTICAL DISTANCE BETWEEN FOURTH AND FIFTH QUARTERED CIRCLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BBBRJ /D/ 04DISTANCE BETWEEN CROSS AND QUARTERED CIRCLE CENTERS,VERTICAL VERTICAL DISTANCE BETWEEN CROSS AND QUARTERED CIRCLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BBBSJ 04RADIUS,CIRCLE,QUARTERED,LARGEST LARGEST QUARTERED CIRCLE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BBBTJ 04RADIUS,CIRCLE,SMALLEST QUARTERED SMALLEST QUARTERED CIRCLE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BBBWL 16STYLE,ARRANGEMENT,MOUNTING PROVISION MOUNTING PROVISION ARRANGEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE MOUNTING PROVISION(S). 1L MODE REPLY 0 BBBXJ 04HEIGHT,TARGET TARGET HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BBBYJ 04WIDTH,TARGET TARGET WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BBBZJ /D/ 04DIAMETER,CIRCLE,CENTER CENTER CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BBCBJ 04RADIUS,CIRCLE,HALF HALF CIRCLE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BBCCA 12QUANTITY PER ROLL,TARGET TARGET QUANTITY PER ROLL THE NUMBER OF TARGET(S) IN A ROLL. 1A MODE REPLY 0 BBCDA 12QUANTITY,SPLINE,FIRST END FIRST END SPLINE QUANTITY THE NUMBER OF FIRST END SPLINE(S) PROVIDED. 1A MODE REPLY 0 BBCFA 12QUANTITY,SPLINE,SECOND END SECOND END SPLINE QUANTITY THE NUMBER OF SECOND END SPLINE(S) PROVIDED. 1A MODE REPLY 0 BBCGD /D/ 07EDGE,STEEL STEEL EDGE AN INDICATION OF WHETHER OR NOT A STEEL EDGE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BBCHA 12QUANTITY,IMAGE,SILHOUETTED SILHOUETTED IMAGE QUANTITY THE NUMBER OF SILHOUETTED IMAGE(S) FURNISHED WITH THE ITEM. 1A MODE REPLY 0 BBCJD 18TYPE,IMAGE,SILHOUETTED SILHOUETTED IMAGE TYPE INDICATES THE TYPE OF SILHOUETTED IMAGE(S) FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AA78 BBCKD 07ADJUSTABILITY,HEIGHT,TRESTLE TRESTLE HEIGHT ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE TRESTLE HEIGHT IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BBCLD 18TYPE,HOLDER,HEAT SOURCE HEAT SOURCE HOLDER TYPE INDICATES THE TYPE OF HEAT SOURCE HOLDER PROVIDED. SELECT REPLY CODE 10AF72 BBCMA 12QUANTITY,OUTLINE,CORRESPONDING,SILHOUETTED IMAGE SILHOUETTED IMAGE CORRESPONDING OUTLINE QUANTITY THE NUMBER OF CORRESPONDING OUTLINE(S) AROUND AND/OR WITHIN THE SILHOUETTED IMAGE(S. 1A MODE REPLY 0 BBCNA 03DESIGNATOR,AREA,CORRESPONDING OUTLINE CORRESPONDING OUTLINE AREA DESIGNATOR THE NUMERIC DESIGNATOR OF THE CORRESPONDING OUTLINE AREAS. 1A MODE REPLY 0 BBCPA 12QUANTITY PER HOLDER,SOURCE,HEAT HEAT SOURCE QUANTITY PER HOLDER THE NUMBER OF HEAT SOURCES EACH HOLDER IS DESIGNED TO HOLD. 1A MODE REPLY 0 BBCQD 18TYPE,TRESTLE TRESTLE TYPE INDICATES THE TYPE OF TRESTLE PROVIDED. SELECT REPLY CODE 10AK54 BBCRJ /D/ 04HEIGHT,OVERALL,SILHOUETTED IMAGE SILHOUETTED IMAGE OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE SILHOUETTED IMAGE. 2D AND 1B MODE REPLY21AA051AC20 BBCSJ /D/ 04WIDTH,OVERALL,SILHOUETTED IMAGE SILHOUETTED IMAGE OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A SILHOUETTED IMAGE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BBCTL /D/ 16STYLE,SEAT,END END SEAT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END SEAT. 1L MODE REPLY 0 BBCWB /D/ 04ANGLE IN DEG,SEAT,END END SEAT ANGLE IN DEG THE ANGLE OF THE END SEAT SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BBCXJ /D/ 04RADIUS,SEAT,END END SEAT RADIUS THE RADIUS OF THE END SEAT SURFACE UPON WHICH THE MATED SURFACE SEATS. 2D AND 1B MODE REPLY21AA051AC20 BBCYD /D/ 13THREAD SERIES DESIGNATOR,END END THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 BBCZJ /D/T13THREAD PITCH DIAMETERS,END END THREAD PITCH DIAMETERS THE END MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 BBDBG /D/ 19PHASE,TRAINING TRAINING PHASE THE TRAINING PHASE/S/ FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 BBDCA 19NUMBER,MODEL,SIMULATED AIRCRAFT SIMULATED AIRCRAFT MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE SIMULATED AIRCRAFT. 1A MODE REPLY 0 BBDDD /D/ 13THREAD DIRECTION,END END THREAD DIRECTION THE DIRECTION OF THE END THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 BBDFL 16STYLE,FEATURE,WRENCHING WRENCHING FEATURE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE WRENCHING FEATURE. 1L MODE REPLY 0 BBDGD /D/ 18TYPE,CONNECTION,END,WRENCHING FEATURE WRENCHING FEATURE END CONNECTION TYPE INDICATES THE TYPE OF WRENCHING FEATURE END CONNECTION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AB76 BBDHA 10CAPACITY,PERSONNEL PERSONNEL CAPACITY A VALUE WHICH REPRESENTS THE NUMBER OF PERSONNEL THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 BBDJD /D/ 18TYPE,END,BOLT BOLT END TYPE INDICATES THE TYPE OF BOLT END PROVIDED. SELECT REPLY CODE 10AK84 BBDKJ /D/ 18TYPE AND SIZE ACCOMMODATED,TUBE,CONNECTION,END END CONNECTION TUBE TYPE AND SIZE ACCOMMODATED INDICATES THE TYPE AND SIZE OF THE TUBE END CONNECTION THE ITEM WILL ACCOMMODATE. 2D AND 1B MODE REPLY21AA053AK84 BBDLD 14SHAPE,CHAMBER CHAMBER SHAPE THE PHYSICAL CONFIGURATION OF THE CHAMBER. SELECT REPLY CODE 10AD07 BBDMJ /D/ 04SIZE,PIPE,NOMINAL,END CONNECTION END CONNECTION NOMINAL PIPE SIZE THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL SIZE OF THE PIPE FOR THE END CONNECTION. 1D AND 1B MODE REPLY11AA05 BBDNJ /D/ 04SIZE,HOSE,NOMINAL,END CONNECTION END CONNECTION NOMINAL HOSE SIZE THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL SIZE OF THE HOSE FOR THE END CONNECTION. 1D AND 1B MODE REPLY11AA05 BBDPB /D/ 04ANGLE IN DEG,SEAT,END CONNECTION END CONNECTION SEAT ANGLE IN DEG THE ANGLE OF THE END CONNECTION SEAT SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BBDQJ /D/ 10PRESSURE AT RATED ALTITUDE,ATMOSPHERIC,MAXIMUM SIMULATED MAXIMUM SIMULATED ATMOSPHERIC PRESSURE AT RATED ALTITUDE THE MAXIMUM SIMULATED ATMOSPHERIC PRESSURE AT RATED ALTITUDE FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AA05 BBDRJ 04LENGTH,COMPARTMENT,CHAMBER CHAMBER COMPARTMENT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CHAMBER COMPARTMENT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BBDSJ 04LENGTH,COMPARTMENT,LOCK LOCK COMPARTMENT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE LOCK COMPARTMENT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BBDTD 18TYPE,POINT POINT TYPE INDICATES THE TYPE OF POINT(S) PROVIDED ON THE ITEM. SELECT REPLY CODE 10AJ44 BBDWA 12QUANTITY,POSITION,STUDENT STUDENT POSITION QUANTITY THE NUMBER OF STUDENT POSITION(S) PROVIDED. 1A MODE REPLY 0 BBDXG 19NAME,EQUIPMENT EQUIPMENT NAME THE NAME OF THE EQUIPMENT. FULL TEXT WRITE-IN 0 BBDYJ 10CAPACITY AND LOCATION CAPACITY AND LOCATION A MEASUREMENT OF THE CAPACITY OF AN ITEM AND ITS LOCATION. 3D AND 1B MODE REPLY32AG671AC203AJ91 BBDZJ /D/ 04SIZE,SHELF SHELF SIZE A MEASUREMENT OF THE SHELF SURFACE(S) OF AN ITEM. 1D AND 1B MODE REPLY12AG67 BBFBJ /D/ 04RADIUS,SEAT,END CONNECTION END CONNECTION SEAT RADIUS THE RADIUS OF THE END CONNECTION SEAT SURFACE UPON WHICH THE MATED SURFACE SEATS. 2D AND 1B MODE REPLY21AA051AC20 BBFCD /D/ 13THREAD SERIES DESIGNATOR,END,WRENCHING FEATURE WRENCHING FEATURE END THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 BBFDD /D/ 13THREAD CLASS,END,WRENCHING FEATURE WRENCHING FEATURE END THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL WRENCHING FEATURE END THREAD. SELECT REPLY CODE 10AN53 BBFFJ /D/ 13THREAD LENGTH AND LOCATION THREAD LENGTH AND LOCATION A MEASUREMENT OF THE EXTENT OF COMPLETE /FULL/ THREADS MEASURED ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS,AND ITS LOCATION. 2D AND 1B MODE REPLY21AA053AJ91 BBFGD 18TYPE,TWIST TWIST TYPE INDICATES THE TYPE OF TWIST PROVIDED. SELECT REPLY CODE 10AG70 BBFHD /D/ 07POINT POINT AN INDICATION OF WHETHER OR NOT A POINT IS INCLUDED. SELECT REPLY CODE 10AA49 BBFJJ 10SIZE,END,CUTTING CUTTING END SIZE DESIGNATES THE SIZE OF THE CUTTING END. 2D AND 1B MODE REPLY21AA051AC20 BBFKJ 04DISTANCE FROM KINGPIN CENTER TO FRONT END DISTANCE FROM KINGPIN CENTER TO FRONT END THE DISTANCE FROM THE KINGPIN CENTER TO THE FRONT END. 1D AND 1B MODE REPLY11AA05 BBFLJ 10CAPACITY RATING,COMPRESSOR COMPRESSOR CAPACITY RATING THE RATED CAPACITY OF THE COMPRESSOR. 1D AND 1B MODE REPLY12AB49 BBFMA /D/ 12QUANTITY,EDGE,FLUTE/CUTTING FLUTE/CUTTING EDGE QUANTITY THE NUMBER OF FLUTES AND/OR CUTTING EDGES PROVIDED. 1A MODE REPLY 0 BBFND 02DESIGN,END,CUTTER CUTTER END DESIGN THE DESIGN OF THE CUTTER END. SELECT REPLY CODE 10AK54 BBFPJ 04DIAMETER,EDGE,CUTTING CUTTING EDGE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CUTTING EDGE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BBFRD /D/ 07CUTTER,FORM FORM CUTTER AN INDICATION OF WHETHER OR NOT A FORM CUTTER IS INCLUDED. SELECT REPLY CODE 10AA49 BBFSD /D/ 07TIP,PILOT PILOT TIP AN INDICATION OF WHETHER OR NOT A PILOT TIP IS INCLUDED. SELECT REPLY CODE 10AA49 BBFTJ 04WIDTH,MAXIMUM,CUT CUT MAXIMUM WIDTH THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CUT OF THE ITEM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BBFWA 12QUANTITY,CUTTER,INSIDE INSIDE CUTTER QUANTITY THE NUMBER OF INSIDE CUTTERS PROVIDED. 1A MODE REPLY 0 BBFXJ 04THICKNESS,CUTTER,INSIDE INSIDE CUTTER THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF AN INSIDE CUTTER,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BBFYA 12QUANTITY,ROLL,POWER FEED POWER FEED ROLL QUANTITY THE NUMBER OF POWER FEED ROLLS PROVIDED. 1A MODE REPLY 0 BBFZA 12QUANTITY,ROLL,ADDITIONAL FEED ADDITIONAL FEED ROLL QUANTITY THE NUMBER OF ADDITIONAL FEED ROLLS PROVIDED. 1A MODE REPLY 0 BBGBJ /D/ 04WIDTH,PLANING PLANING WIDTH A MEASUREMENT OF THE PLANING WIDTH,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BBGCJ /D/ 04DEPTH,RABBETING RABBETING DEPTH A MEASUREMENT OF THE RABBETING DEPTH,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BBGDJ 04WIDTH ACCOMMODATED,MATERIAL MATERIAL WIDTH ACCOMMODATED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MATERIAL THE ITEM WILL ACCOMMODATE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BBGFA 12QUANTITY,HEAD,CUTTER CUTTER HEAD QUANTITY THE NUMBER OF CUTTER HEADS PROVIDED. 1A MODE REPLY 0 BBGGJ 04DIAMETER,CYLINDER,CUTTER HEAD CUTTER HEAD CYLINDER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CUTTER HEAD CYLINDER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BBGHJ 04DIAMETER,CIRCLE,CUTTER HEAD CUTTING CUTTER HEAD CUTTING CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CUTTER HEAD CUTTING CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BBGJA 12QUANTITY,KNIFE,CUTTER HEAD CUTTER HEAD KNIFE QUANTITY THE NUMBER OF CUTTER HEAD KNIVES PROVIDED. 1A MODE REPLY 0 BBGKJ 04LENGTH,OVERALL,TABLE TABLE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE TABLE. 2D AND 1B MODE REPLY21AA051AC20 BBGLB 04ANGLE IN DEG,TILT,TABLE TABLE TILT ANGLE IN DEG THE ANGLE OF THE TABLE TILT,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BBGMJ 04LENGTH,OVERALL,FENCE FENCE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE FENCE. 2D AND 1B MODE REPLY21AA051AC20 BBGNB 04ANGLE IN DEG,TILT,FENCE FENCE TILT ANGLE IN DEG THE ANGLE OF THE FENCE TILT,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BBGPD 18TYPE,CARRIAGE CARRIAGE TYPE INDICATES THE TYPE OF CARRIAGE PROVIDED. SELECT REPLY CODE 10AJ77 BBGQA 12QUANTITY,TRUCK,CARRIAGE CARRIAGE TRUCK QUANTITY THE NUMBER OF CARRIAGE TRUCKS PROVIDED. 1A MODE REPLY 0 BBGRA 12QUANTITY PER TRUCK,WHEEL WHEEL QUANTITY PER TRUCK THE NUMBER OF WHEELS PROVIDED ON EACH TRUCK. 1A MODE REPLY 0 BBGSJ 04DIAMETER,AXLE AXLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE AXLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BBGTD /D/ 07FEATURE,SCRAPER,AUTOMATIC REVERSIBLE TRACK AUTOMATIC REVERSIBLE TRACK SCRAPER FEATURE AN INDICATION OF WHETHER OR NOT AN AUTOMATIC REVERSIBLE TRACK SCRAPER/S/ FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BBGWA /D/ 12QUANTITY,BLOCK,STEEL HEAD STEEL HEAD BLOCK QUANTITY THE NUMBER OF STEEL HEAD BLOCK(S) PROVIDED. 1A MODE REPLY 0 BBGXD /D/ 07FEATURE,DRIVE,WIRE CABLE WIRE CABLE DRIVE FEATURE AN INDICATION OF WHETHER OR NOT A WIRE CABLE DRIVE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BBGYJ /D/ 04LENGTH,HUSK HUSK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE HUSK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BBGZJ /D/ 04WIDTH,HUSK HUSK WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE HUSK,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BBHBJ 04LENGTH,CARRIAGE CARRIAGE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CARRIAGE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BBHCJ 04WIDTH,CARRIAGE CARRIAGE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CARRIAGE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BBHDJ 04LENGTH,TRACKWAY TRACKWAY LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TRACKWAY,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BBHFG /D/ 04DIMENSION,DIRECTION,RIBBON RIBBON DIRECTION DIMENSION THE DIMENSION MEASURED PARALLEL TO THE DIRECTION IN WHICH THE CONTINUOUS STRIP OF WEB IS LAID. FULL TEXT WRITE-IN 0 BBHGG /D/ 04DIMENSION,DIRECTION,DESIGNED RIBBON DESIGNED RIBBON DIRECTION DIMENSION THE SIZE WHICH IS ATTAINED AFTER THE CORE MATERIAL IS EXPANDED TO THE FULL CELL SIZE. FULL TEXT WRITE-IN 0 BBHHG /D/ 04DIMENSION,DIRECTION,TRANSVERSE TRANSVERSE DIRECTION DIMENSION THE DIMENSION MEASURED PARALLEL TO THE DIRECTION IN WHICH THE CORE MATERIAL IS PULLED BY EXPANSION. FULL TEXT WRITE-IN 0 BBHJG /D/ 04DIMENSION,DIRECTION,DESIGNED TRANSVERSE DESIGNED TRANSVERSE DIRECTION DIMENSION THE SIZE WHICH IS ATTAINED AFTER THE CORE MATERIAL IS EXPANDED TO THE FULL CELL SIZE,BUT NOT OVEREXPANDED. FULL TEXT WRITE-IN 0 BBHKG /D/ 10RANGE,SCALE SCALE RANGE AN INDICATION OF THE SCALE/S/ RANGE. PLEASE USE MRC APSK IN PLACE OF THIS CANCELED MRC. FULL TEXT WRITE-IN 0 BBHLG 10GRADUATION,INCREMENT,SMALLEST,SCALE SCALE SMALLEST INCREMENT GRADUATION THE SMALLEST GRADUATION VALUE(S) BETWEEN THE MARKINGS ON A SCALE. FULL TEXT WRITE-IN 0 BBHMJ /D/ 19LEGEND T LEGEND T NONE. 2D AND 1B MODE REPLY21AA051AC20 BBHNJ /D/ 19LEGEND W LEGEND W NONE. 2D AND 1B MODE REPLY21AA051AC20 BBHPJ /D/ 19LEGEND X LEGEND X NONE. 2D AND 1B MODE REPLY21AA051AC20 BBHQJ /D/A18TYPE AND QUANTITY,INTERCONNECTION INTERCONNECTION TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF INTERCONNECTION(S) PROVIDED. 1D AND 1A MODE REPLY11AD81 BBHRD /D/ 19ARRANGEMENT,CONNECTION,ELECTRODE ELECTRODE CONNECTION ARRANGEMENT THE TERM USED TO IDENTIFY THE ELECTRICAL CONNECTION ARRANGEMENT BETWEEN THE INDIVIDUAL DEVICES. SELECT REPLY CODE 10AE15 BBHSJ /D/A18TYPE AND QUANTITY,TERMINAL TERMINAL TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF TERMINAL(S) FOR PROVIDING ELECTRICAL CONNECTION. 1D AND 1A MODE REPLY12AA58 BBHTJ 10FREQUENCY RATING,AMPLIFIER AMPLIFIER FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE AMPLIFIER IS RATED. 3D AND 1B MODE REPLY31AC321AC201AC00 BBHWJ 10CAPACITY RATING,RADIATOR RADIATOR CAPACITY RATING AN INDICATION OF THE RATED CAPACITY OF A RADIATOR. 1D AND 1B MODE REPLY12AG67 BBHXH /D/ 19IDENTIFIER,UNIT,INDIVIDUAL INDIVIDUAL UNIT IDENTIFIER THE IDENTIFICATION OF EACH OF THE COMPONENT UNITS WHICH COMPRISE THE ITEM. 2D MODE REPLY 22AM752AK80 BBHYJ /D/ 10VOLTAGE RATING AND TYPE,INPUT,AC,MAXIMUM MAXIMUM AC INPUT VOLTAGE RATING AND TYPE THE MAXIMUM SUSTAINED VALUE AND TYPE OF ALTERNATING CURRENT VOLTAGE THAT CAN SAFELY BE APPLIED TO THE INPUT TERMINALS OF AN ITEM WITHOUT RISKING THE POSSIBILITY OF ELECTRICAL BREAKDOWN. 2D AND 1B MODE REPLY21AB631AF65 BBHZJ /D/ 10VOLTAGE RATING,OUTPUT,DC DC OUTPUT VOLTAGE RATING THE RATED VALUE OF DIRECT CURRENT OUTPUT THAT CAN BE SUPPLIED BY THE ITEM. 1D AND 1B MODE REPLY11AB63 BBJBD /D/ 18TYPE,LOAD,ELECTRICAL ELECTRICAL LOAD TYPE THE PREDOMINATE ELECTRICAL CHARACTERISTIC OF THE CIRCUIT WHICH RECEIVES THE OUTPUT OF THE ITEM. SELECT REPLY CODE 10AK53 BBJCG 19AGENCY,CONTROLLING,DOCUMENT DOCUMENT CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY,COMMERCIAL ORGANIZATION,OR OTHER SOURCE,WHICH CONTROLS THE DOCUMENT. FULL TEXT WRITE-IN 0 BBJDD 18TYPE,EFFECT,FIELD FORCE FIELD FORCE EFFECT TYPE INDICATES THE TYPE OF FIELD FORCE THAT COULD HAVE DETRIMENTAL EFFECTS ON THE SERVICEABILITY OF THE DEVICE DURING NORMAL HANDLING OR STORAGE. SELECT REPLY CODE 10AM76 BBJFD /D/ 19CLIPS,SHORTING,LEAD LEAD SHORTING CLIPS A JUMPER CONNECTING LEADS AND TERMINALS TO PRECLUDE BODY/TRANSIENT CHARGES THAT MAY BE ENCOUNTERED PRIOR TO PACKAGING OR AFTER REMOVAL OF THE PROTECTIVE PACKAGING MATERIALS. SELECT REPLY CODE 10AM78 BBJGD 19FINISH,DIAL DIAL FINISH AN INDICATION OF THE FINISH ON THE DIAL. SELECT REPLY CODE 10AB54 BBJHD 19NAME,KNOB KNOB NAME THE NOMENCLATURE BY WHICH THE KNOB IS IDENTIFIED. SELECT REPLY CODE 10AL15 BBJJA 12QUANTITY,POINT,MOUNTING MOUNTING POINT QUANTITY THE NUMBER OF MOUNTING POINT(S) PROVIDED. 1A MODE REPLY 0 BBJKJ 04LENGTH,OVERALL,CUTTER HEAD KNIFE CUTTER HEAD KNIFE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CUTTER HEAD KNIFE. 2D AND 1B MODE REPLY21AA051AC20 BBJLJ 04WIDTH,OVERALL,TABLE TABLE OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A TABLE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BBJMJ 04HEIGHT,OVERALL,FENCE FENCE OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE FENCE. 2D AND 1B MODE REPLY21AA051AC20 BBJND 19DEVICE,INDICATOR,TEMP TEMP INDICATOR DEVICE THE DEVICE USED TO REGISTER THE TEMPERATURE. SELECT REPLY CODE 10AB28 BBJPD 19CHARACTERISTIC,STABILIZATION,RETICLE RETICLE STABILIZATION CHARACTERISTIC AN INDICATION OF THE RETICLE STABILIZATION CHARACTERISTIC. SELECT REPLY CODE 10AL15 BBJQD /D/ 07ILLUMINATION,RETICLE RETICLE ILLUMINATION AN INDICATION OF WHETHER OR NOT RETICLE ILLUMINATION IS PROVIDED. SELECT REPLY CODE 10AB22 BBJRD 18TYPE,CHART,RECORDING RECORDING CHART TYPE INDICATES THE TYPE OF RECORDING CHART PROVIDED. SELECT REPLY CODE 10AM12 BBJSD /D/ 11METHOD,ACTUATION,CHART CHART ACTUATION METHOD THE MEANS BY WHICH THE CHART IS ACTUATED. SELECT REPLY CODE 10AC58 BBJTD 19NAME,HANDLE HANDLE NAME THE NOMENCLATURE BY WHICH THE HANDLE IS IDENTIFIED. SELECT REPLY CODE 10AL15 BBJWD 08LOCATION,HANDLE HANDLE LOCATION INDICATES THE LOCATION OF THE HANDLE ON THE ITEM. SELECT REPLY CODE 10AJ91 BBJXD 19POSITION,MOUNTING MOUNTING POSITION THE INSTALLED POSITION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AM84 BBJYD /D/ 07ELEMENT,HEATING,ELECTRICAL ELECTRICAL HEATING ELEMENT AN INDICATION OF WHETHER OR NOT AN ELECTRICAL HEATING ELEMENT IS PROVIDED. SELECT REPLY CODE 10AB22 BBJZD 18TYPE,CURRENT,HEATING ELEMENT HEATING ELEMENT CURRENT TYPE INDICATES THE TYPE OF HEATING ELEMENT CURRENT WHETHER ALTERNATING,DIRECT,OR BOTH. SELECT REPLY CODE 10AB62 BBKBD 19PHASE,ELEMENT,HEATING HEATING ELEMENT PHASE THE NUMBER OF ALTERNATING CURRENT PHASES FOR WHICH THE HEATING ELEMENT IS DESIGNED. SELECT REPLY CODE 10AD02 BBKCB 10FREQUENCY IN HERTZ,ELEMENT,HEATING HEATING ELEMENT FREQUENCY IN HERTZ THE CYCLES PER SECOND /HERTZ/ OF ALTERNATING CURRENT FOR WHICH THE HEATING ELEMENT IS DESIGNED. 1B MODE REPLY 0 BBKFJ /D/T13THREAD PITCH DIAMETERS,END,WRENCHING FEATURE WRENCHING FEATURE END THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD OF A WRENCHING FEATURE END. 1D AND 1F MODE REPLY11AA05 BBKGD /D/ 13THREAD DIRECTION,END,WRENCHING FEATURE WRENCHING FEATURE END THREAD DIRECTION THE DIRECTION OF THE WRENCHING FEATURE END THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 BBKHJ /D/ 13THREAD LENGTH,END,WRENCHING FEATURE WRENCHING FEATURE END THREAD LENGTH A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL THREAD AXIS OF A WRENCHING FEATURE END. 2D AND 1B MODE REPLY21AA051AC20 BBKJD /D/ 13THREAD LOCATION,END,WRENCHING FEATURE WRENCHING FEATURE END THREAD LOCATION THE WRENCHING FEATURE END PORTION/S/ OF AN ITEM ON WHICH THE THREAD/S/ IS LOCATED. SELECT REPLY CODE 10AJ91 BBKKJ 04DISTANCE FROM BOLT END TO HOLE CENTER DISTANCE FROM BOLT END TO HOLE CENTER THE DISTANCE MEASURED ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS OF THE BOLT END TO HOLE CENTER. 2D AND 1B MODE REPLY21AA051AC20 BBKLJ 04DIAMETER FROM WRENCHING FEATURE,FIRST FIRST DIAMETER FROM WRENCHING FEATURE NONE. 2D AND 1B MODE REPLY21AA051AC20 BBKMJ 04DIAMETER FROM WRENCHING FEATURE,SECOND SECOND DIAMETER FROM WRENCHING FEATURE NONE. 2D AND 1B MODE REPLY21AA051AC20 BBKNJ 04DIAMETER FROM WRENCHING FEATURE,THIRD THIRD DIAMETER FROM WRENCHING FEATURE NONE. 2D AND 1B MODE REPLY21AA051AC20 BBKPJ 04DIAMETER FROM WRENCHING FEATURE,FOURTH FOURTH DIAMETER FROM WRENCHING FEATURE NONE. 2D AND 1B MODE REPLY21AA051AC20 BBKQJ 04DIAMETER FROM WRENCHING FEATURE,FIFTH FIFTH DIAMETER FROM WRENCHING FEATURE NONE. 2D AND 1B MODE REPLY21AA051AC20 BBKRJ 04LENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO END OF FIRST DIAMETER LENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO END OF FIRST DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BBKSJ 04LENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO END OF SECOND DIAMETER LENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO END OF SECOND DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BBKTJ 04LENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO END OF THIRD DIAMETER LENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO END OF THIRD DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BBKWJ 04LENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO END OF FOURTH DIAMETER LENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO END OF FOURTH DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BBKXJ 04LENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO END OF FIFTH DIAMETER LENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO END OF FIFTH DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BBKYJ 04DIAMETER,HOLE,FLUID,FIRST RADIAL FIRST RADIAL FLUID HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BBKZJ 04DIAMETER,HOLE,FLUID,SECOND RADIAL SECOND RADIAL FLUID HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BBLBJ 04DISTANCE FROM FIRST RADIAL HOLE CENTER TO END OF BOLT DISTANCE FROM FIRST RADIAL HOLE CENTER TO END OF BOLT NONE. 2D AND 1B MODE REPLY21AA051AC20 BBLCJ 04DISTANCE FROM SECOND RADIAL HOLE CENTER TO END OF BOLT DISTANCE FROM SECOND RADIAL HOLE CENTER TO END OF BOLT NONE. 2D AND 1B MODE REPLY21AA051AC20 BBLDJ 04LENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO BOLT END LENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO BOLT END NONE. 2D AND 1B MODE REPLY21AA051AC20 BBLFJ 04HEIGHT,FEATURE,WRENCHING WRENCHING FEATURE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BBLGD /D/ 13THREAD LOCATION,END END THREAD LOCATION THE END PORTION(S) OF AN ITEM ON WHICH THE THREAD(S) IS LOCATED. SELECT REPLY CODE 10AJ91 BBLHJ 10CAPACITY,DISPENSING DISPENSING CAPACITY THE RATED DISPENSING CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BBLJJ 10CAPACITY,HARDENING HARDENING CAPACITY THE RATED HARDENING CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BBLKJ /D/ 10CAPACITY,STORAGE,MIX MIX STORAGE CAPACITY THE MIX STORAGE CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BBLLJ 04WIDTH,SURFACE,SEALING,INSERT PLUG INSERT PLUG SEALING SURFACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SEALING SURFACE OF THE INSERT PLUG,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BBLMJ 04HEIGHT,SURFACE,SEALING,INSERT PLUG INSERT PLUG SEALING SURFACE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE SEALING SURFACE OF AN INSERT PLUG,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BBLNJ 10TEMP RATING,WATER,INLET INLET WATER TEMP RATING THE TEMPERATURE OF THE INLET WATER AT WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY11AB36 BBLPJ 10CAPACITY PER CAN,ICE ICE CAPACITY PER CAN THE AMOUNT OF ICE EACH CAN WILL HOLD. 1D AND 1B MODE REPLY12AG67 BBLQJ 10CAPACITY PER BATCH,FREEZER FREEZER CAPACITY PER BATCH THE RATED FREEZER CAPACITY PER BATCH OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BBLRJ 10CAPACITY,HARDENING/DISPENSING,TOTAL TOTAL HARDENING/DISPENSING CAPACITY THE TOTAL HARDENING/DISPENSING CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BBLSJ 10CAPACITY PER HOUR,DRAW OFF DRAW OFF CAPACITY PER HOUR THE CAPACITY PER HOUR THAT MAY BE DRAWN OFF. 1D AND 1B MODE REPLY12AG67 BBLTJ 10CAPACITY RATING CAPACITY RATING A MEASUREMENT OF THE CAPACITY OF AN ITEM. 2D AND 1B MODE REPLY22AG671AC20 BBLWD 07FOLDABILITY FOLDABILITY AN INDICATION OF WHETHER OR NOT THE ITEM IS FOLDABLE. SELECT REPLY CODE 10AM73 BBLXJ 04DIAMETER,MAXIMUM,SHANK SHANK MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHANK,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BBLYJ 04WIDTH,LINE,PRODUCED PRODUCED LINE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE LINE PRODUCED BY THE ITEM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BBLZD 07ADJUSTABILITY,FLOW,INK INK FLOW ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE INK FLOW IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BBMBD 07DETACHABILITY,RESERVOIR,INK INK RESERVOIR DETACHABILITY AN INDICATION OF WHETHER OR NOT THE INK RESERVOIR IS DETACHABLE. SELECT REPLY CODE 10AH97 BBMCD 18TYPE,PIN,CLEANING CLEANING PIN TYPE INDICATES THE TYPE OF CLEANING PIN PROVIDED. SELECT REPLY CODE 10AK54 BBMDD 18TYPE,SCRIBER SCRIBER TYPE INDICATES THE TYPE OF SCRIBER PROVIDED. SELECT REPLY CODE 10AK54 BBMFD 18TYPE,PEN PEN TYPE INDICATES THE TYPE OF PEN PROVIDED. SELECT REPLY CODE 10AK54 BBMGA 12QUANTITY,WHEEL,DOTTING DOTTING WHEEL QUANTITY THE NUMBER OF DOTTING WHEEL/S/. 1A MODE REPLY 0 BBMHD 08LOCATION,ADJUSTMENT ADJUSTMENT LOCATION INDICATES THE LOCATION OF THE ADJUSTMENT ON THE ITEM. SELECT REPLY CODE 10AJ91 BBMJD 18TYPE,CONNECTION,HANDLE HANDLE CONNECTION TYPE INDICATES THE TYPE OF HANDLE CONNECTION PROVIDED. SELECT REPLY CODE 10AK54 BBMKJ 10CAPACITY,COMPARTMENT,FROZEN FOOD FROZEN FOOD COMPARTMENT CAPACITY THE CAPACITY OF THE COMPARTMENT FOR FROZEN FOOD. 1D AND 1B MODE REPLY12AG67 BBMLJ /D/ 10CAPACITY,STORAGE/DRAW OFF STORAGE/DRAW OFF CAPACITY THE CAPACITY WHICH THE ITEM BOTH STORES AND MAKES AVAILABLE TO BE DRAWN OFF. 1D AND 1B MODE REPLY12AG67 BBMMD 13THREAD LOCATION,SCREW SCREW THREAD LOCATION INDICATES THE LOCATION OF THE SCREW THREAD. SELECT REPLY CODE 10AJ91 BBMND /D/ 07LOCK,SWIVEL SWIVEL LOCK AN INDICATION OF WHETHER OR NOT A SWIVEL LOCK IS INCLUDED. SELECT REPLY CODE 10AA49 BBMPD /D/ 07JOINT,KNEE KNEE JOINT AN INDICATION OF WHETHER OR NOT A KNEE JOINT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BBMQD /D/ 07THUMBSCREW,GRADUATED GRADUATED THUMBSCREW AN INDICATION OF WHETHER OR NOT A GRADUATED THUMBSCREW IS INCLUDED. SELECT REPLY CODE 10AA49 BBMRD 14SHAPE,HANDLE HANDLE SHAPE THE PHYSICAL CONFIGURATION OF THE HANDLE. SELECT REPLY CODE 10AD07 BBMSD 18TYPE,CURVE CURVE TYPE INDICATES THE TYPE OF CURVE PROVIDED. SELECT REPLY CODE 10AK54 BBMTA 12QUANTITY,CURVE CURVE QUANTITY THE NUMBER OF CURVE(S) PROVIDED. 1A MODE REPLY 0 BBMWD 19FACILITY,LIFTING LIFTING FACILITY THE FACILITY PROVIDED FOR LIFTING THE ITEM. SELECT REPLY CODE 10AC55 BBMXJ A19ANGLE AND QUANTITY ANGLE AND QUANTITY THE ANGLE INDICATED AND THE NUMBER OF EACH. 1D AND 1A MODE REPLY13AJ92 BBMYD 19PROFILE,TRIANGLE TRIANGLE PROFILE THE REPRESENTATION OF A TRIANGLE IN OUTLINE. SELECT REPLY CODE 10AM77 BBMZD /D/ 09MATERIAL,ARM ARM MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ARM(S) IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BBNBJ 04LENGTH,BAR BAR LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A BAR,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BBNCA 10RATIO,ENLARGING,MAXIMUM MAXIMUM ENLARGING RATIO A NUMERIC RELATIONSHIP REFLECTING THE MAXIMUM EXPANSION OF THE ITEM. 1A MODE REPLY 0 BBNDA 10RATIO,REDUCING,MAXIMUM MAXIMUM REDUCING RATIO A NUMERIC RELATIONSHIP REFLECTING THE MAXIMUM REDUCTION OF THE ITEM. 1A MODE REPLY 0 BBNFD /D/ 09MATERIAL,NEEDLE NEEDLE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE NEEDLE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BBNGJ 04LENGTH,EFFECTIVE,TRACER ARM TRACER ARM EFFECTIVE LENGTH A MEASUREMENT OF THE LONGEST ACTUAL DIMENSION OF THE TRACER ARM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BBNHJ 04LENGTH,MAXIMUM,POLE ARM POLE ARM MAXIMUM LENGTH THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF THE POLE ARM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BBNJJ /D/ 04LENGTH,RAIL RAIL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE RAIL,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BBNKJ /D/ 04DISTANCE OF RAIL TO AXIS OF MOMENT DISTANCE OF RAIL TO AXIS OF MOMENT THE DISTANCE OF THE RAIL TO THE AXIS OF THE MOMENTS. 1D AND 1B MODE REPLY11AA05 BBNLJ 10READING,MINIMUM,VERNIER VERNIER MINIMUM READING THE SMALLEST INCREMENT OF MEASURE REPRESENTED BY THE MARKINGS ON A VERNIER. 1D AND 1B MODE REPLY12AG67 BBNMJ 10RANGE,LONGITUDINAL LONGITUDINAL RANGE A MEASUREMENT OF THE DIFFERENCE BETWEEN THE MINIMUM AND MAXIMUM LENGTHWISE DIMENSION. 1D AND 1B MODE REPLY11AA05 BBNNJ 10RANGE,TRANSVERSE TRANSVERSE RANGE A MEASUREMENT OF THE DIFFERENCE BETWEEN THE MINIMUM AND MAXIMUM CROSSWISE DIMENSION. 1D AND 1B MODE REPLY11AA05 BBNPJ B04SIZE FOR WHICH DESIGNED,MAXIMUM,DRAWING DRAWING MAXIMUM SIZE FOR WHICH DESIGNED THE MAXIMUM SIZE OF THE DRAWING FOR WHICH THE ITEM IS DESIGNED. 1D AND 1F MODE REPLY11AA05 BBNQD /D/ 18TYPE,SCALE,AIRCRAFT NAVIGATIONAL AIRCRAFT NAVIGATIONAL SCALE TYPE INDICATES THE TYPE OF AIRCRAFT NAVIGATIONAL SCALE PROVIDED. SELECT REPLY CODE 10AM12 BBNRA 12QUANTITY,SCALE,CHUCK PLATE CHUCK PLATE SCALE QUANTITY THE NUMBER OF SCALE(S) PROVIDED WITH THE CHUCK PLATE. 1A MODE REPLY 0 BBNSJ 04LENGTH,SCALE SCALE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SCALE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BBNTJ 04LENGTH,ARM ARM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ARM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BBNWJ 04DIAMETER,PROTRACTOR PROTRACTOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PROTRACTOR,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BBNXD /D/ 07PROTRACTOR PROTRACTOR AN INDICATION OF WHETHER OR NOT A PROTRACTOR IS INCLUDED. SELECT REPLY CODE 10AA49 BBNYD 18TYPE,PROTRACTOR PROTRACTOR TYPE INDICATES THE TYPE OF PROTRACTOR PROVIDED. SELECT REPLY CODE 10AL36 BBNZG 10CALIBRATION,PROTRACTOR PROTRACTOR CALIBRATION AN INDICATION OF THE MANNER IN WHICH THE PROTRACTOR IS CALIBRATED. FULL TEXT WRITE-IN 0 BBPBJ 10PERCENTAGE,GRADATION,SIEVE PARTICLE SIZE SIEVE PARTICLE SIZE GRADATION PERCENTAGE THE PERCENTAGE OF MATERIAL RETAINED AND/OR PASSED THROUGH A SPECIFIED STANDARD SIEVE. 3D AND 1B MODE REPLY31AC202AM793AF81 BBPCJ 04DIAMETER,MANDREL,SAW SAW MANDREL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SAW MANDREL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BBPDJ 04LENGTH,MANDREL,SAW SAW MANDREL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SAW MANDREL,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BBPFD 18TYPE,FACE,SAW MANDREL PULLEY SAW MANDREL PULLEY FACE TYPE INDICATES THE TYPE OF SAW MANDREL PULLEY FACE PROVIDED. SELECT REPLY CODE 10AG89 BBPGJ 04DIAMETER,BORE,PULLEY PULLEY BORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR PULLEY BORE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BBPHD 02DESIGN,BLADE,SAW SAW BLADE DESIGN THE DESIGN OF THE SAW BLADE. SELECT REPLY CODE 10AL25 BBPJJ 04DIAMETER,BLADE BLADE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR BLADE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BBPKA /D/ 16STYLE,HOLE,ARBOR ARBOR HOLE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ARBOR HOLE. 1A MODE REPLY 0 BBPLD /D/ 07RIG,SAW,TOP TOP SAW RIG AN INDICATION OF WHETHER OR NOT A TOP SAW RIG IS INCLUDED. SELECT REPLY CODE 10AA49 BBPMJ /D/ 04DIAMETER,MAXIMUM,BLADE BLADE MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BLADE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BBPNJ 04LENGTH,ADAPTER ADAPTER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BBPPJ /D/ 04WIDTH,ADAPTER ADAPTER WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BBPQJ 04HEIGHT,ADAPTER ADAPTER HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BBPRD /D/ 09MATERIAL,ADAPTER,ACTUATOR ACTUATOR ADAPTER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ACTUATOR ADAPTER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BBPSD /D/ 18TYPE ACCOMMODATED,ACTUATOR ACTUATOR TYPE ACCOMMODATED INDICATES THE TYPE OF ACTUATOR THAT THE ITEM IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AC58 BBPTJ 04DIAMETER,UNIT,UNPACKAGED UNPACKAGED UNIT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR ITEM,UNENCUMBERED BY PACKAGING OR PACKING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BBPWD /D/ 09MATERIAL,FRAME,CARRIAGE CARRIAGE FRAME MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH AN ITEM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BBPXJ 04DEPTH,COMPARTMENT COMPARTMENT DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF A COMPARTMENT,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 BBPYJ 04DIAMETER,INSIDE,TOP TOP INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO INSIDE SURFACES OF A CIRCULAR FIGURE OR BODY,MEASURED AT THE TOP OF THE ITEM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BBPZD /D/ 07PLATE,PROTECTING,PEEL PEEL PROTECTING PLATE AN INDICATION OF WHETHER OR NOT A PEEL PROTECTING PLATE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BBQBD /D/ 07LEG LEG AN INDICATION OF WHETHER OR NOT A LEG(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BBQCJ 04LENGTH FOR WHICH DESIGNED,OPENING,STEAM TABLE STEAM TABLE OPENING LENGTH FOR WHICH DESIGNED A MEASUREMENT OF THE LONGEST DIMENSION OF THE STEAM TABLE OPENING FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BBQDJ 04WIDTH FOR WHICH DESIGNED,OPENING,STEAM TABLE STEAM TABLE OPENING WIDTH FOR WHICH DESIGNED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE STEAM TABLE OPENING FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BBQFD /D/ 07SPIGOT SPIGOT AN INDICATION OF WHETHER OR NOT A SPIGOT IS INCLUDED. SELECT REPLY CODE 10AA49 BBQGJ 04DIAMETER,OVERALL,BLADE BLADE OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF A BLADE. 2D AND 1B MODE REPLY21AA051AC20 BBQHD /D/ 09MATERIAL,VESSEL,INNER INNER VESSEL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INNER VESSEL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BBQJG /D/ 04SIZE,MOUTH MOUTH SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE MOUTH. FULL TEXT WRITE-IN 0 BBQKD 14SHAPE,INSIDE,MOUTH MOUTH INSIDE SHAPE THE PHYSICAL CONFIGURATION OF THE INSIDE OF THE MOUTH. SELECT REPLY CODE 10AD07 BBQLD /D/ 07OPENING,SPOUT,BOTTOM DISPENSING BOTTOM DISPENSING SPOUT OPENING AN INDICATION OF WHETHER OR NOT A BOTTOM DISPENSING SPOUT OPENING IS PROVIDED. SELECT REPLY CODE 10AB22 BBQMD 18TYPE,SPOUT SPOUT TYPE INDICATES THE TYPE OF SPOUT PROVIDED. SELECT REPLY CODE 10AK54 BBQND /D/ 07VALVE,CONTROL,FLOW FLOW CONTROL VALVE AN INDICATION OF WHETHER OR NOT A FLOW CONTROL VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 BBQPD /D/ 07SPOUT,POURING,FUNNEL TYPE FUNNEL TYPE POURING SPOUT AN INDICATION OF WHETHER OR NOT A FUNNEL TYPE POURING SPOUT IS PROVIDED. SELECT REPLY CODE 10AB22 BBQQD /D/ 07EXTENSION,FLEXIBLE FLEXIBLE EXTENSION AN INDICATION OF WHETHER OR NOT A FLEXIBLE EXTENSION IS INCLUDED. SELECT REPLY CODE 10AA49 BBQRD /D/ 07LIP,POURING POURING LIP AN INDICATION OF WHETHER OR NOT A POURING LIP IS INCLUDED. SELECT REPLY CODE 10AA49 BBQSD /D/ 07GLASS,RESISTANT,HEAT HEAT RESISTANT GLASS AN INDICATION OF WHETHER OR NOT A LOW EXPANSION GLASS THAT IS RESISTANT TO THERMAL CHANGE IS INCLUDED. SELECT REPLY CODE 10AA49 BBQTJ 04DIAMETER,BEARING,END MILL END MILL BEARING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE INSIDE CENTER OF AN END MILL BEARING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BBQWD 05DIRECTION FOR WHICH DESIGNED,CUTTER CUTTER DIRECTION FOR WHICH DESIGNED THE DIRECTION OF THE CUTTER FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AA38 BBQXA 04SIZE,ARBOR ARBOR SIZE THE ALPHA AND/OR NUMERIC SIZE DESIGNATION BY WHICH THE ARBOR IS IDENTIFIED. 1A MODE REPLY 0 BBQYJ 10CAPACITY ACCOMMODATED CAPACITY ACCOMMODATED A MEASUREMENT OF THE CAPACITY THE ITEM WILL ACCOMMODATE. 2D AND 1B MODE REPLY22AG671AC20 BBQZJ /D/ 04WIDTH ACROSS FLATS,HOLE,TOOL HEAD TOOL HEAD HOLE WIDTH ACROSS FLATS THE DISTANCE FROM ONE FLAT TO THE OPPOSITE FLAT OF A TOOL HEAD HOLE. 2D AND 1B MODE REPLY21AA051AC20 BBRBJ 04DIAMETER,END END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE END OF THE ITEM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BBRCJ 19COMPOSITION AND PERCENTAGE COMPOSITION AND PERCENTAGE THE VALUES/S/ OF THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE COMPOSITION IS FABRICATED,EXCLUDING IMPURITIES. 3D AND 1B MODE REPLY31AC202AG555AG54 BBRDJ 04LENGTH,OVERALL,BLADE BLADE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BLADE. 2D AND 1B MODE REPLY21AA051AC20 BBRFG 10LIMITATION IN PERCENT,IMPURITIES IMPURITIES LIMITATION IN PERCENT LIMITATIONS PLACED ON SPECIFIC IMPURITIES TO MAKE THE ITEM SUITABLE FOR PARTICULAR USES,EXPRESSED IN PERCENT. FULL TEXT WRITE-IN 0 BBRGD 18TYPE,STORAGE STORAGE TYPE INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS. SELECT REPLY CODE 10AM81 BBRHJ A19FREQUENCY,INSPECTION INSPECTION FREQUENCY THE SPECIFIED TIME INTERVAL,FROM RECEIPT,NECESSARY TO DETECT MATERIAL DETERIORATION THAT WILL AFFECT STOCK READINESS. 2D AND 1A MODE REPLY22AH682AM82 BBRJD 19FEATURE,HANDLING,SPECIAL SPECIAL HANDLING FEATURE THE UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING. SELECT REPLY CODE 10AM83 BBRKD 19DERIVATION DERIVATION THE SOURCE OR ORIGIN OF THE ITEM. SELECT REPLY CODE 10AM85 BBRLJ T10RANGE,TEMP,MELTING POINT MELTING POINT TEMP RANGE THE MINIMUM AND MAXIMUM TEMPERATURES WHICH INDICATE THE MELTING POINT OF THE ITEM. 1D AND 1F MODE REPLY13AJ40 BBRMJ 10TEMP,DISTILLATION DISTILLATION TEMP THE NUMERIC VALUE WHICH INDICATES THE TEMPERATURE LEVEL USED IN DETERMINING THE DISTILLATION DATA. 3D AND 1B MODE REPLY33AJ401AC202AM86 BBRNJ 10PERCENTAGE,EVAPORATION,DISTILLATION DISTILLATION EVAPORATION PERCENTAGE THE PROPORTION OF THE SUBSTANCE EVAPORATED DURING DISTILLATION. 2D AND 1B MODE REPLY21AC202AM86 BBRPJ /D/ 10VALUE,GRAVITY,SPECIFIC SPECIFIC GRAVITY VALUE THE NUMERIC VALUE INDICATING THE RATIO OF THE MASS OF A BODY TO THE MASS OF AN EQUAL VOLUME OF WATER AT A SPECIFIED TEMPERATURE. 1D AND 1B MODE REPLY11AC20 BBRQJ /D/ 10TEMP AT SPECIFIC GRAVITY RATIO,SUBSTANCE/WATER SUBSTANCE/WATER TEMP AT SPECIFIC GRAVITY RATIO PLEASE USE MRC CJXH IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1B MODE REPLY13AJ40 BBRRB 10INCREMENT IN DEG,MINIMUM,PROTRACTOR PROTRACTOR MINIMUM INCREMENT IN DEG THE SMALLEST VALUE BETWEEN MARKINGS ON A PROTRACTOR,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BBRSD /D/ 07GRADUATIONS,QUADRANT,PROTRACTOR PROTRACTOR QUADRANT GRADUATIONS AN INDICATION OF WHETHER OR NOT GRADUATIONS ARE PROVIDED WITH THE PROTRACTOR. SELECT REPLY CODE 10AB22 BBRTB 10INCREMENT IN DEG,MINIMUM,PROTRACTOR QUADRANT PROTRACTOR QUADRANT MINIMUM INCREMENT IN DEG THE SMALLEST VALUE BETWEEN MARKINGS ON A PROTRACTOR QUADRANT,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BBRWG /D/ 10GRADUATION,SCALE,OUTER,DIAL DIAL OUTER SCALE GRADUATION AN INDICATION OF THE OUTER SCALE GRADUATION ON THE DIAL. FULL TEXT WRITE-IN 0 BBRXG /D/ 10GRADUATION,SCALE,INNER,DIAL DIAL INNER SCALE GRADUATION AN INDICATION OF THE INNER SCALE GRADUATION ON THE DIAL. FULL TEXT WRITE-IN 0 BBRYA /D/ 12QUANTITY,DIAL,GRADUATION GRADUATION DIAL QUANTITY THE NUMBER OF GRADUATION DIAL(S) PROVIDED. 1A MODE REPLY 0 BBRZG /D/ 10GRADUATION,DIAL,INDIVIDUAL INDIVIDUAL DIAL GRADUATION AN INDICATION OF THE INDIVIDUAL DIAL GRADUATION(S). FULL TEXT WRITE-IN 0 BBSBG /D/ 10GRADUATION,WHEEL,DIAL MEASURING DIAL MEASURING WHEEL GRADUATION AN INDICATION OF THE DIAL MEASURING WHEEL GRADUATION/S/. FULL TEXT WRITE-IN 0 BBSCD /D/ 07MAGNIFIER,MOUNTED MOUNTED MAGNIFIER AN INDICATION OF WHETHER OR NOT A MOUNTED MAGNIFIER IS INCLUDED. SELECT REPLY CODE 10AA49 BBSDD /D/ 07SCREW,ADJUSTING ADJUSTING SCREW AN INDICATION OF WHETHER OR NOT AN ADJUSTING SCREW IS INCLUDED. SELECT REPLY CODE 10AA49 BBSFD 14SHAPE,LEG LEG SHAPE THE PHYSICAL CONFIGURATION OF THE LEG. SELECT REPLY CODE 10AD07 BBSGD 08LOCATION,SCREW,ADJUSTMENT ADJUSTMENT SCREW LOCATION INDICATES THE LOCATION OF THE ADJUSTMENT SCREW ON THE ITEM. SELECT REPLY CODE 10AJ91 BBSHD /D/ 07DEVICE,STRAIGHTENING STRAIGHTENING DEVICE AN INDICATION OF WHETHER OR NOT A STRAIGHTENING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 BBSJD /D/ 07ARC ARC AN INDICATION OF WHETHER OR NOT AN ARC IS INCLUDED. SELECT REPLY CODE 10AA49 BBSKD /D/ 07BEAM BEAM AN INDICATION OF WHETHER OR NOT A BEAM IS INCLUDED. SELECT REPLY CODE 10AA49 BBSLD /D/ 07COUPLER COUPLER AN INDICATION OF WHETHER OR NOT A COUPLER IS INCLUDED. SELECT REPLY CODE 10AA49 BBSMD /D/ 07DESIGN,FITTED FITTED DESIGN AN INDICATION OF WHETHER OR NOT A FITTED DESIGN IS INCLUDED. SELECT REPLY CODE 10AA49 BBSNA 12QUANTITY,CLAMP CLAMP QUANTITY THE NUMBER OF CLAMPS PROVIDED. 1A MODE REPLY 0 BBSPD /D/ 09MATERIAL,CLAMP CLAMP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CLAMP(S) IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BBSQD 07MOVABILITY,CLAMP CLAMP MOVABILITY AN INDICATION OF WHETHER OR NOT THE CLAMP IS MOVABLE. SELECT REPLY CODE 10AM87 BBSRD /D/ 07ADJUSTMENT,MICROMETER,CLAMP CLAMP MICROMETER ADJUSTMENT AN INDICATION OF WHETHER OR NOT A CLAMP MICROMETER ADJUSTMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BBSSG 19NAME AND QUANTITY,POINT POINT NAME AND QUANTITY THE NAME AND NUMBER OF POINT(S) INCLUDED WITH THE ITEM. FULL TEXT WRITE-IN 0 BBSTD /D/ 07LENS,MAGNIFYING MAGNIFYING LENS AN INDICATION OF WHETHER OR NOT A MAGNIFYING LENS IS INCLUDED. SELECT REPLY CODE 10AA49 BBSWF /D/T10RATIO,SCALE SCALE RATIO THE RELATIONSHIP IN QUANTITY,AMOUNT,OR SIZE BETWEEN TWO OR MORE SCALES. 1F MODE REPLY 0 BBSXA 12QUANTITY,VERNIER VERNIER QUANTITY THE NUMBER OF VERNIER(S) PROVIDED. 1A MODE REPLY 0 BBSYJ 10INCREMENT,SMALLEST,VERNIER VERNIER SMALLEST INCREMENT THE SMALLEST VALUE BETWEEN MARKINGS ON THE VERNIER. 1D AND 1B MODE REPLY12AG67 BBSZA 12QUANTITY,SCREW,TANGENT TANGENT SCREW QUANTITY THE NUMBER OF TANGENT SCREW(S) PROVIDED. 1A MODE REPLY 0 BBTBB 10CURRENT RATING IN AMPS,ELEMENT,HEATING HEATING ELEMENT CURRENT RATING IN AMPS THE TOTAL ELECTRICAL CURRENT OF THE HEATING ELEMENT,EXPRESSED IN AMPERES. 1B MODE REPLY 0 BBTCD 18TYPE,THROAT THROAT TYPE INDICATES THE TYPE OF THROAT PROVIDED. SELECT REPLY CODE 10AK54 BBTDF T10RANGE,NUMBER,MACH MACH NUMBER RANGE THE MACH NUMBER RANGE FOR WHICH THE ITEM IS RATED. 1F MODE REPLY 0 BBTFB 10VOLTAGE IN VOLTS,ELEMENT,HEATING HEATING ELEMENT VOLTAGE IN VOLTS THE TOTAL VALUE OF ELECTRICAL POTENTIAL FOR WHICH THE HEATING ELEMENT IS RATED,EXPRESSED IN VOLTS. 1B MODE REPLY 0 BBTGB 10WATTAGE IN WATTS,ELEMENT,HEATING HEATING ELEMENT WATTAGE IN WATTS THE RATED POWER THE HEATING ELEMENT CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS. 1B MODE REPLY 0 BBTHF T10RANGE IN RPM,SPEED,MOTOR MOTOR SPEED RANGE IN RPM THE SPEED RANGE OF THE MOTOR,EXPRSSED IN REVOLUTIONS PER MINUTE. 1F MODE REPLY 0 BBTJJ 10POWER RATING,DRIVING,DRUM DRUM DRIVING POWER RATING THE RATED DRIVING POWER OF THE DRUM. 2D AND 1B MODE REPLY21AA561AC20 BBTKJ /D/ 10POWER FOR ONE MINUTE,BRAKING,DRUM DRUM BRAKING POWER FOR ONE MINUTE THE RATED BRAKING POWER OF THE DRUM FOR ONE MINUTE. 1D AND 1B MODE REPLY12AG67 BBTLB 10SPEED IN RPM,MAXIMUM,DRUM DRUM MAXIMUM SPEED IN RPM THE MAXIMUM RATED SPEED OF THE DRUM,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 BBTMA 12QUANTITY,VALVE,INTERNAL INTERNAL VALVE QUANTITY THE NUMBER OF INTERNAL VALVE(S) PROVIDED. 1A MODE REPLY 0 BBTND 19ERRORS COMPENSATED ERRORS COMPENSATED AN INDICATION OF THE ERRORS THE ITEM IS DESIGNED TO COMPENSATE. SELECT REPLY CODE 10AJ41 BBTPG /D/ 10COMPENSATION RANGE IN DEG,ERROR ERROR COMPENSATION RANGE IN DEG THE MINIMUM TO MAXIMUM LIMITS OF DEVIATION COMPENSATION FOR EACH ERROR,EXPRESSED IN DEGREES. FULL TEXT WRITE-IN 0 BBTQD 18TYPE,ELEMENT,SENSING SENSING ELEMENT TYPE INDICATES THE TYPE OF SENSING ELEMENT PROVIDED. SELECT REPLY CODE 10AJ77 BBTRB 10ANGULAR ROTATION IN DEG,TOTAL TOTAL ANGULAR ROTATION IN DEG THE TOTAL ANGULAR ROTATION OF THE ITEM,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BBTSB 10ACCURACY RATING IN DEG ACCURACY RATING IN DEG THE PERMISSIBLE DEVIATION OF THE ITEM,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BBTTJ A18TYPE AND QUANTITY,COMBINATION COMBINATION TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF COMBINATION(S) PROVIDED WITH THE ITEM. 1D AND 1A MODE REPLY11AG97 BBTWG /D/ 10RANGE,VELOCITY,OPERATING OPERATING VELOCITY RANGE AN INDICATION OF THE MINIMUM AND MAXIMUM VALUES OF VELOCITY AT WHICH THE ITEM IS DESIGNED TO OPERATE. FULL TEXT WRITE-IN 0 BBTXJ 10PRESSURE,DIFFERENTIAL,CASE CASE DIFFERENTIAL PRESSURE THE DIFFERENCE IN OPPOSING PRESSURE WHICH THE CASE IS CAPABLE OF WITHSTANDING WITHOUT EVIDENCE OF DEFORMATION OR OTHER DAMAGE. 1D AND 1B MODE REPLY11AB18 BBTYA 04SIZE,AWG,CABLE CABLE AWG SIZE DESIGNATES THE AMERICAN WIRE GAGE SIZE OF THE CABLE. 1A MODE REPLY 0 BBTZG /D/ 19NUMBER,IDENTIFYING,CABLE CONNECTOR CABLE CONNECTOR IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE CABLE CONNECTOR. FULL TEXT WRITE-IN 0 BBWBD 11METHOD,APPLICATION,ELASTIC RESTRAINT ELASTIC RESTRAINT APPLICATION METHOD THE MEANS BY WHICH THE ELASTIC RESTRAINT IS APPLIED. SELECT REPLY CODE 10AF22 BBWCD 11METHOD,INTEGRATION INTEGRATION METHOD THE MEANS OF INTEGRATION. SELECT REPLY CODE 10AD49 BBWDD 11METHOD,POWER,WHEEL WHEEL POWER METHOD THE MEANS USED TO FURNISH WHEEL POWER. SELECT REPLY CODE 10AL40 BBWFA 12QUANTITY,AXIS,FREEDOM FREEDOM AXIS QUANTITY THE NUMBER OF FREEDOM AXIS(ES) PROVIDED. 1A MODE REPLY 0 BBWGA 12QUANTITY,GIMBAL GIMBAL QUANTITY THE NUMBER OF GIMBAL(S) PROVIDED. 1A MODE REPLY 0 BBWHG /D/ 10LIMITATION IN DEG,DISPLACEMENT,AXIS AXIS DISPLACEMENT LIMITATION IN DEG A MEASUREMENT OF THE AXIS DISPLACEMENT,EXPRESSED IN DEGREES. FULL TEXT WRITE-IN 0 BBWJD 11METHOD,APPLICATION,GIMBAL TORQUE GIMBAL TORQUE APPLICATION METHOD THE MEANS USED TO APPLY TORQUE TO THE GIMBALS. SELECT REPLY CODE 10AJ12 BBWKA 12QUANTITY,GIMBAL,TORQUED TORQUED GIMBAL QUANTITY THE NUMBER OF TORQUED GIMBAL/S/ PROVIDED. 1A MODE REPLY 0 BBWLG /D/ 11METHOD,LEVEL,SENSING OUTPUT/SIGNAL SENSING OUTPUT/SIGNAL LEVEL METHOD THE MEANS USED TO INDICATE THE SENSING OUTPUT AND SIGNAL LEVEL. FULL TEXT WRITE-IN 0 BBWMD 11METHOD,CONTROL,TEMP TEMP CONTROL METHOD THE MEANS USED TO CONTROL THE TEMPERATURE OF AN ITEM. SELECT REPLY CODE 10AD16 BBWND 18TYPE,INSTRUMENT INSTRUMENT TYPE INDICATES THE TYPE OF INSTRUMENT PROVIDED. SELECT REPLY CODE 10AK54 BBWPD 18TYPE,FLUID FLUID TYPE INDICATES THE TYPE OF FLUID USED IN THE ITEM. SELECT REPLY CODE 10AB75 BBWRJ 04DIAMETER,FACILITY,READING READING FACILITY DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR READING FACILITY,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BBWSD 19INSCRIPTION,UNIT OF MEASURE,READING FACILITY READING FACILITY UNIT OF MEASURE INSCRIPTION THE STANDARD OR VALUATION AS REPRESENTED BY THE INSCRIPTION ON THE READING FACILITY. SELECT REPLY CODE 10AB49 BBWTF T10RANGE,GRADUATION,READING FACILITY READING FACILITY GRADUATION RANGE THE MINIMUM AND MAXIMUM NUMERIC VALUES REPRESENTING THE GRADUATION COVERAGE OF THE READING FACILITY. 1F MODE REPLY 0 BBWWJ 10INCREMENT,SMALLEST,READING FACILITY READING FACILITY SMALLEST INCREMENT THE SMALLEST VALUE BETWEEN THE MARKINGS ON A READING FACILITY. 1D AND 1B MODE REPLY12AG67 BBWXD 19FINISH,FACILITY,READING READING FACILITY FINISH AN INDICATION OF THE FINISH ON THE READING FACILITY. SELECT REPLY CODE 10AB54 BBWYJ 04LENGTH,NEEDLE NEEDLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE NEEDLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BBWZD 19FINISH,NEEDLE NEEDLE FINISH AN INDICATION OF THE FINISH ON THE NEEDLE. SELECT REPLY CODE 10AB54 BBXFD /D/ 07FEATURE,TILTING TILTING FEATURE AN INDICATION OF WHETHER OR NOT A TILTING FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BBXGB 10WATTAGE RATING IN WATTS,SPEAKER SPEAKER WATTAGE RATING IN WATTS THE RATED POWER THAT A SPEAKER CAN SAFELY PROVIDE,MEASURED IN WATTS. 1B MODE REPLY 0 BBXHA 12QUANTITY,SPEAKER SPEAKER QUANTITY THE NUMBER OF SPEAKER(S) PROVIDED WITH THE ITEM. 1A MODE REPLY 0 BBXJD 18TYPE,VALVE,MAIN MAIN VALVE TYPE INDICATES THE TYPE OF MAIN VALVE(S) PROVIDED. SELECT REPLY CODE 10AG25 BBXKD 18TYPE,VALVE,KEY CHANGE KEY CHANGE VALVE TYPE INDICATES THE TYPE OF VALVE PROVIDED TO CHANGE THE FUNDAMENTAL KEY DESIGNATION OF AN ITEM. SELECT REPLY CODE 10AG25 BBXLD 19PITCH PITCH AN INDICATION OF THE PITCH THE ITEM IS ABLE TO OBTAIN. SELECT REPLY CODE 10AH87 BBXMD 19UNIT FOR WHICH DESIGNED UNIT FOR WHICH DESIGNED A PARTICULAR UNIT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AH87 BBXNG 04SIZE,UNIT UNIT SIZE DESIGNATES THE SIZE BY WHICH THE UNIT IS KNOWN AND/OR IDENTIFIED. FULL TEXT WRITE-IN 0 BBXPD /D/ 07ROD,BEATER,ADJUSTABLE ADJUSTABLE BEATER ROD AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE BEATER ROD IS PROVIDED. SELECT REPLY CODE 10AB22 BBXQD 18TYPE,POST POST TYPE INDICATES THE TYPE OF POST PROVIDED ON THE ITEM. SELECT REPLY CODE 10AL76 BBXRD /D/ 07PROTECTOR,HEAD,FIBER FIBER HEAD PROTECTOR AN INDICATION OF WHETHER OR NOT A FIBER HEAD PROTECTOR IS PROVIDED. SELECT REPLY CODE 10AB22 BBXSD /D/ 03DESIGNATION,INSIGNIA INSIGNIA DESIGNATION THE DESIGNATION ASSIGNED TO AN INSIGNIA FOR THE PURPOSE OF IDENTIFICATION. SELECT REPLY CODE 10AL31 BBXTJ 04DIAMETER,SKIN SKIN DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SKIN,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BBXWD 18TYPE,FASTENER FASTENER TYPE INDICATES THE TYPE OF FASTENER PROVIDED ON THE ITEM. SELECT REPLY CODE 10AC52 BBXXD 01COLOR,UNIT UNIT COLOR THE COLOR ASSIGNED TO A UNIT FOR IDENTIFICATION. SELECT REPLY CODE 10AD06 BBXYD /D/ 09MATERIAL,BALL BALL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BALL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BBXZD /D/ 01COLOR,CORD CORD COLOR THE HUE OR TINT OF THE CORD. SELECT REPLY CODE 10AD06 BBYBD /D/ 01COLOR,TASSEL TASSEL COLOR THE HUE OR TINT OF THE TASSEL. SELECT REPLY CODE 10AD06 BBYCD /D/ 07KIT,TUNING TUNING KIT AN INDICATION OF WHETHER OR NOT A TUNING KIT IS INCLUDED. SELECT REPLY CODE 10AA49 BBYDD 11METHOD,PRODUCTION,TONE TONE PRODUCTION METHOD THE MEANS USED TO PRODUCE TONE. SELECT REPLY CODE 10AC58 BBYFA 12QUANTITY,MANUAL MANUAL QUANTITY THE NUMBER OF MANUALS PROVIDED WITH THE ITEM. 1A MODE REPLY 0 BBYGA 12QUANTITY,STRING STRING QUANTITY THE NUMBER OF STRINGS PROVIDED ON THE ITEM. 1A MODE REPLY 0 BBYHA 12QUANTITY,FRET FRET QUANTITY THE NUMBER OF FRETS PROVIDED ON THE ITEM. 1A MODE REPLY 0 BBYJD /D/ 07SET,STRING,SPARE SPARE STRING SET AN INDICATION OF WHETHER OR NOT A SPARE SET OF STRINGS ARE INCLUDED. SELECT REPLY CODE 10AA49 BBYKD 14SHAPE,TOP TOP SHAPE THE PHYSICAL CONFIGURATION OF THE TOP OF THE ITEM. SELECT REPLY CODE 10AD07 BBYLA 12QUANTITY,BUTTON,BASS BASS BUTTON QUANTITY THE NUMBER OF BASS BUTTONS PROVIDED ON THE ITEM. 1A MODE REPLY 0 BBYMA 12QUANTITY,KEY,TREBLE TREBLE KEY QUANTITY THE NUMBER OF TREBLE KEYS PROVIDED ON THE ITEM. 1A MODE REPLY 0 BBYNA 12QUANTITY,OCTAVE OCTAVE QUANTITY THE NUMBER OF OCTAVES PROVIDED ON THE ITEM. 1A MODE REPLY 0 BBYPG /D/ 19RANGE,NOTE NOTE RANGE AN INDICATION OF THE NOTE RANGE THE ITEM WILL PROVIDE. FULL TEXT WRITE-IN 0 BBYQJ 04DIAMETER,OUTSIDE,TUBE TUBE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BBYRD /D/ 17SURFACE TREATMENT,TUBE TUBE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE TUBE SURFACE. SELECT REPLY CODE 10AD09 BBYSA 12QUANTITY,BAR BAR QUANTITY THE NUMBER OF BARS PROVIDED ON THE ITEM. 1A MODE REPLY 0 BBYTD 18TYPE,STRING STRING TYPE INDICATES THE TYPE OF STRING PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AC52 BBYWA 03DESIGNATOR,PITCH PITCH DESIGNATOR THE ALPHA AND/OR NUMERIC DESIGNATOR THAT IDENTIFIES THE PITCH. 1A MODE REPLY 0 BBYXD /D/ 07INTENSITY,SOUND,ADJUSTABLE ADJUSTABLE SOUND INTENSITY AN INDICATION OF WHETHER OR NOT AN ADJUSTMENT FOR SOUND INTENSITY IS PROVIDED. SELECT REPLY CODE 10AB22 BBYYD /D/ 07AID,TIMING,VISUAL VISUAL TIMING AID AN INDICATION OF WHETHER OR NOT A VISUAL TIMING AID IS PROVIDED. SELECT REPLY CODE 10AB22 BBYZG 04SIZE FOR WHICH DESIGNED,INSTRUMENT INSTRUMENT SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE INSTRUMENT FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 BBZBD /D/ 07LOCK,CLAMP CLAMP LOCK AN INDICATION OF WHETHER OR NOT A CLAMP LOCK IS INCLUDED. SELECT REPLY CODE 10AA49 BBZCD 19CLOSING TO ZERO MARK,ARM,MOVABLE MOVABLE ARM CLOSING TO ZERO MARK AN INDICATION OF THE MOVABLE ARM THAT CAN BE CLOSED TO THE ZERO MARK. SELECT REPLY CODE 10AH21 BBZDD /D/ 07ARM,EXTENSION EXTENSION ARM AN INDICATION OF WHETHER OR NOT AN EXTENSION ARM(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BBZFJ 04LENGTH,ARM,EXTENSION EXTENSION ARM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE EXTENSION ARM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BBZGD /D/ 09MATERIAL,CENTER CENTER MATERIAL THE ELEMENT,COUPOUND,OR MIXTURE OF WHICH THE CENTER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BBZHD 18TYPE,DESIGN,GRADUATION GRADUATION DESIGN TYPE INDICATES THE TYPE OF GRADUATION(S) FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BBZJD /D/ 07TABLE,SETTING SETTING TABLE AN INDICATION OF WHETHER OR NOT A SETTING/S/ TABLE IS INCLUDED. SELECT REPLY CODE 10AA49 BBZKD /D/ 07MOVEMENT,RACK RACK MOVEMENT AN INDICATION OF WHETHER OR NOT A RACK MOVEMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BBZLD /D/ 07VERNIER,SLIDE,PIVOT PIVOT SLIDE VERNIER AN INDICATION OF WHETHER OR NOT A PIVOT SLIDE VERNIER IS INCLUDED. SELECT REPLY CODE 10AA49 BBZMD /D/ 07JOINT,KNEE,LEG LEG KNEE JOINT AN INDICATION OF WHETHER OR NOT A LEG KNEE JOINT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BBZND /D/ 07DEVICE,STRAIGHTENING,LEG LEG STRAIGHTENING DEVICE AN INDICATION OF WHETHER OR NOT A LEG STRAIGHTENING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 BBZPD 18TYPE,POINT,NEEDLE,LEG LEG NEEDLE POINT TYPE INDICATES THE TYPE OF LEG NEEDLE POINT(S) PROVIDED. SELECT REPLY CODE 10AB47 BBZQD 18TYPE,TOP TOP TYPE INDICATES THE TYPE OF TOP PROVIDED. SELECT REPLY CODE 10AM35 BBZTD /D/ 09MATERIAL,LEG LEG MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LEG(S) IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BBZZD 07ADJUSTABILITY,TILT TILT ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE TILT IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BCBBF T10RANGE IN DEG,TILT TILT RANGE IN DEG THE MINIMUM AND MAXIMUM TILT OF THE ITEM,EXPRESSED IN DEGREES. 1F MODE REPLY 0 BCBCD /D/ 09MATERIAL,SURFACE,ILLUMINATED ILLUMINATED SURFACE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ILLUMINATED SURFACE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BCBDJ 04LENGTH,SURFACE,ILLUMINATED ILLUMINATED SURFACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ILLUMINATED SURFACE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BCBFJ 04WIDTH,SURFACE,ILLUMINATED ILLUMINATED SURFACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ILLUMINATED SURFACE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BCBGJ 04THICKNESS,OVERALL,BOARD BOARD OVERALL THICKNESS AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF THE BOARD,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BCBHD 07ADJUSTABILITY,BOARD BOARD ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE BOARD IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BCBJB 04ANGLE IN DEG,TILT,HORIZONTAL,MAXIMUM MAXIMUM HORIZONTAL TILT ANGLE IN DEG THE MAXIMUM HORIZONTAL TILT ANGLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BCBKD /D/ 07TROUGH,INSTRUMENT INSTRUMENT TROUGH AN INDICATION OF WHETHER OR NOT AN INSTRUMENT TROUGH IS INCLUDED. SELECT REPLY CODE 10AA49 BCBLD 07ADJUSTABILITY,HEIGHT HEIGHT ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE HEIGHT IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BCBMA /D/ 12QUANTITY,PEDESTAL PEDESTAL QUANTITY THE NUMBER OF PEDESTAL(S) PROVIDED. PLEASE USE MRC BGDH IN PLACE OF THIS DISCONTINUED MRC. 1A MODE REPLY 0 BCBND /D/ 09MATERIAL,PEDESTAL PEDESTAL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PEDESTAL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BCBPA 12QUANTITY,DRAWER DRAWER QUANTITY THE NUMBER OF DRAWERS PROVIDED. 1A MODE REPLY 0 BCBQD /D/ 09MATERIAL,DRAWER DRAWER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE DRAWER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BCBRJ 04LENGTH,INSIDE,DRAWER DRAWER INSIDE LENGTH AN INSIDE MEASUREMENT OF THE LONGEST DIMENSION OF A DRAWER,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BCBSJ 04WIDTH,INSIDE,DRAWER DRAWER INSIDE WIDTH AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE DRAWER,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BCBTJ 04DEPTH,INSIDE,DRAWER DRAWER INSIDE DEPTH AN INSIDE MEASUREMENT BETWEEN SPECIFIED POINTS ON THE DRAWER,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 BCBWD /D/ 07LOCK,DRAWER DRAWER LOCK AN INDICATION OF WHETHER OR NOT A DRAWER LOCK IS INCLUDED. SELECT REPLY CODE 10AA49 BCBXD /D/ 07SURFACE,REFERENCE,STATIONARY STATIONARY REFERENCE SURFACE AN INDICATION OF WHETHER OR NOT A STATIONARY REFERENCE SURFACE IS INCLUDED. SELECT REPLY CODE 10AA49 BCBYD /D/ 07REST,FOOT FOOT REST AN INDICATION OF WHETHER OR NOT A FOOT REST IS INCLUDED. SELECT REPLY CODE 10AA49 BCBZJ 04LENGTH,END SHOULDER TO NUT END SHOULDER TO NUT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ITEM FROM THE END SHOULDER TO THE NUT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BCCBD /D/ 07PILOT,END END PILOT AN INDICATION OF WHETHER OR NOT AN END PILOT IS INCLUDED. SELECT REPLY CODE 10AA49 BCCCD /D/ 07NUT,CLAMP CLAMP NUT AN INDICATION OF WHETHER OR NOT A CLAMP NUT IS INCLUDED. SELECT REPLY CODE 10AA49 BCCDD /D/ 07SPACER SPACER AN INDICATION OF WHETHER OR NOT A SPACER(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BCCFD /D/ 07SLEEVE,BEARING BEARING SLEEVE AN INDICATION OF WHETHER OR NOT A BEARING SLEEVE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BCCGJ 04THICKNESS,HOLE,ARBOR ARBOR HOLE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ARBOR HOLE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BCCHJ 04DIAMETER,OUTSIDE,END END OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE END,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BCCJJ 04DIAMETER,OUTSIDE,STEP STEP OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE STEP,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BCCKD /D/ 07STUD STUD AN INDICATION OF WHETHER OR NOT A STUD IS INCLUDED. SELECT REPLY CODE 10AA49 BCCLA 12QUANTITY,STUD STUD QUANTITY THE NUMBER OF STUD(S) PROVIDED. 1A MODE REPLY 0 BCCMJ /D/ 04DIAMETER,CIRCLE,STUD STUD CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A STUD CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BCCNG /D/ 04SPACING,STUD STUD SPACING THE SPACING BETWEEN THE STUD CENTERS. FULL TEXT WRITE-IN 0 BCCPJ /D/ 04WIDTH ACROSS FLATS,MAJOR MAJOR WIDTH ACROSS FLATS A MEASUREMENT OF THE LARGEST DISTANCE FROM ONE FLAT TO THE OPPOSITE FLAT,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BCCQJ /D/ 04WIDTH ACROSS FLATS,MINOR MINOR WIDTH ACROSS FLATS A MEASUREMENT OF THE SMALLEST DISTANCE FROM ONE FLAT TO THE OPPOSITE FLAT,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BCCRJ /D/ 04DISTANCE FROM CENTER OF FLAT TO OPPOSITE SIDE,PERPENDICULAR PERPENDICULAR DISTANCE FROM CENTER OF FLAT TO OPPOSITE SIDE THE DISTANCE FROM THE CENTER OF A FLAT TO THE PERIPHERY OF THE OPPOSITE SIDE. 2D AND 1B MODE REPLY21AA051AC20 BCCSJ T04SIZE RANGE ACCOMMODATED,SAW SAW SIZE RANGE ACCOMMODATED THE MEASUREMENT OF THE MINIMUM TO THE MAXIMUM SAW SIZE THE ITEM WILL ACCOMMODATE. 1D AND 1F MODE REPLY11AA05 BCCTJ 04DIAMETER,DRILL,PILOT PILOT DRILL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PILOT DRILL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BCCWD /D/ 07ACCOMMODATION,POINT,INSERTED INSERTED POINT ACCOMMODATION AN INDICATION OF WHETHER OR NOT AN INSERTED POINT ACCOMMODATION IS PROVIDED. SELECT REPLY CODE 10AB22 BCCXD 07REPLACEABILITY,POINT POINT REPLACEABILITY AN INDICATION OF WHETHER OR NOT THE POINT IS REPLACEABLE. SELECT REPLY CODE 10AG84 BCCYG 04SIZE,SHANK SHANK SIZE THE DESIGNATION BY WHICH THE SIZE OF THE SHANK IS IDENTIFIED. FULL TEXT WRITE-IN 0 BCCZJ 04DIAMETER,MAXIMUM MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ITEM,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BCDBD 14SHAPE,SHANK,POINT POINT SHANK SHAPE THE PHYSICAL CONFIGURATION OF THE POINT SHANK. SELECT REPLY CODE 10AD07 BCDCD /D/ 07CORE,POLE,INTEGRAL INTEGRAL POLE CORE AN INDICATION OF WHETHER OR NOT AN INTEGRAL POLE CORE IS INCLUDED. SELECT REPLY CODE 10AA49 BCDDJ 04RADIUS,CURVATURE CURVATURE RADIUS THE DIMENSION FROM THE CENTER OF THE CIRCLE TO THE OUTSIDE SURFACE. 2D AND 1B MODE REPLY21AA051AC20 BCDFB 12QUANTITY,TURN,CONDUCTOR CONDUCTOR TURN QUANTITY THE NUMBER OF CONDUCTOR TURN(S) PROVIDED. 1B MODE REPLY 0 BCDGA 12QUANTITY,CONDUCTOR,PARALLEL PARALLEL CONDUCTOR QUANTITY THE NUMBER OF PARALLEL CONDUCTOR(S) PROVIDED. 1A MODE REPLY 0 BCDHJ 04WIDTH,WIRE,CONDUCTOR CONDUCTOR WIRE WIDTH A MEASUREMENT OF THE LARGEST CROSS-SECTIONAL DIMENSION OF THE FLAT SHAPED WIRE TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE WIRE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BCDJJ 04THICKNESS,WIRE,CONDUCTOR CONDUCTOR WIRE THICKNESS A MEASUREMENT OF THE SMALLEST CROSS-SECTIONAL DIMENSION OF THE FLAT SHAPED WIRE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BCDKJ /D/ 04SIZE,WIRE,CONDUCTOR CONDUCTOR WIRE SIZE DESIGNATES THE SIZE OF THE WIRE USED IN THE CONDUCTOR. 1D AND 1B MODE REPLY12AG67 BCDMD /D/ 07HANDLE,PLATED PLATED HANDLE AN INDICATION OF WHETHER OR NOT A PLATED HANDLE IS INCLUDED. SELECT REPLY CODE 10AA49 BCDNA 12QUANTITY,TINE TINE QUANTITY THE NUMBER OF TINES INCLUDED ON THE ITEM. 1A MODE REPLY 0 BCDPD /D/ 11METHOD,OPERATION,ADJUSTMENT DEVICE ADJUSTMENT DEVICE OPERATION METHOD THE MEANS USED TO OPERATE THE ADJUSTMENT DEVICE. SELECT REPLY CODE 10AL41 BCDQD 13THREAD SERIES,CONNECTION,OUTLET OUTLET CONNECTION THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF A THREADED OUTLET CONNECTION. SELECT REPLY CODE 10AH06 BCDRA 12QUANTITY,MEMBER,CROSS CROSS MEMBER QUANTITY THE NUMBER OF CROSS MEMBERS PROVIDED ON THE ITEM. 1A MODE REPLY 0 BCDSD /D/ 19ARRANGEMENT,MEMBER,CROSS CROSS MEMBER ARRANGEMENT THE ARRANGEMENT OF THE CROSS MEMBER/S/ ON THE ITEM. SELECT REPLY CODE 10AJ91 BCDTD /D/ 07ACCOMMODATION,JACK,LEVELING LEVELING JACK ACCOMMODATION AN INDICATION OF WHETHER OR NOT AN ACCOMMODATION/S/ FOR A LEVELING JACK IS INCLUDED. SELECT REPLY CODE 10AA49 BCDWD /D/ 07GATE,TILTING,CASTER CASTER TILTING GATE AN INDICATION OF WHETHER OR NOT A CASTER TILTING GATE IS INCLUDED. SELECT REPLY CODE 10AA49 BCDXJ 04DIAMETER,WHEEL WHEEL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WHEEL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BCDYD 11METHOD,CONVEYANCE CONVEYANCE METHOD THE MEANS USED TO CONVEY THE ITEM. SELECT REPLY CODE 10AA78 BCFBA 13THREAD SIZE,HEAD HEAD THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A HOLE. 1A MODE REPLY 0 BCFCA /D/ 13THREAD SIZE,SCREW,BINDING,HEAD HEAD BINDING SCREW THREAD SIZE DESIGNATES THE SCREW THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A HEAD BINDING. 1A MODE REPLY 0 BCFDD /D/ 09MATERIAL,HEAD,TAPERED SPINDLE TAPERED SPINDLE HEAD MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH A TAPERED SPINDLE HEAD IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BCFFJ /D/ 04DIAMETER,TUBE,ACCOMMODATED HEAD SUPPORT ACCOMMODATED HEAD SUPPORT TUBE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HEAD SUPPORT TUBE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BCFGD /D/ 07TUBE,SUPPORT,HEAD HEAD SUPPORT TUBE AN INDICATION OF WHETHER OR NOT A HEAD SUPPORT TUBE IS INCLUDED. SELECT REPLY CODE 10AA49 BCFHD /D/ 07ADAPTER,HEAD HEAD ADAPTER AN INDICATION OF WHETHER OR NOT AN ADAPTER IS INCLUDED. SELECT REPLY CODE 10AA49 BCFJD /D/ 07STRAP,ASSEMBLY ASSEMBLY STRAP AN INDICATION OF WHETHER OR NOT AN ASSEMBLY STRAP IS INCLUDED. SELECT REPLY CODE 10AA49 BCFKG 19NAME,MANUFACTURER,END ITEM END ITEM MANUFACTURER NAME THE NAME OF THE MANUFACTURER OF THE END ITEM. FULL TEXT WRITE-IN 0 BCFLG /D/ 19ADDRESS,MANUFACTURER,END ITEM END ITEM MANUFACTURER ADDRESS THE ADDRESS OF THE MANUFACTURER OF THE END ITEM. FULL TEXT WRITE-IN 0 BCFMD 18TYPE,LEG LEG TYPE INDICATES THE TYPE OF LEG PROVIDED. SELECT REPLY CODE 10AK54 BCFND 19CONSTRUCTION,LEG LEG CONSTRUCTION THE STRUCTURAL CHARACTERISTIC OF THE LEG. SELECT REPLY CODE 10AL59 BCFPA 12QUANTITY PER LEG,SECTION SECTION QUANTITY PER LEG THE NUMBER OF SECTIONS FOR EACH LEG. 1A MODE REPLY 0 BCFQD /D/ 09MATERIAL,TIP,FOOT FOOT TIP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FOOT TIP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BCFRD /D/ 07STRAP,HOLDING HOLDING STRAP AN INDICATION OF WHETHER OR NOT A HOLDING STRAP IS INCLUDED. SELECT REPLY CODE 10AA49 BCFSD /D/ 09MATERIAL,ASSEMBLY,ROLLER ROLLER ASSEMBLY MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ROLLER ASSEMBLY IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BCFTD /D/ 07TUNNEL,GUIDE CORD GUIDE CORD TUNNEL AN INDICATION OF WHETHER OR NOT A GUIDE CORD TUNNEL IS INCLUDED. SELECT REPLY CODE 10AA49 BCFWD 18TYPE,TUNNEL,GUIDE CORD GUIDE CORD TUNNEL TYPE INDICATES THE TYPE OF GUIDE CORD TUNNEL PROVIDED. SELECT REPLY CODE 10AK54 BCFXD /D/ 07LEDGE,PENCIL PENCIL LEDGE AN INDICATION OF WHETHER OR NOT A PENCIL LEDGE IS INCLUDED. SELECT REPLY CODE 10AA49 BCFYA 12QUANTITY,EDGE EDGE QUANTITY THE NUMBER OF EDGE(S) PROVIDED. 1A MODE REPLY 0 BCFZD /D/ 09MATERIAL,EDGE EDGE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE EDGE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BCGBD /D/ 09MATERIAL,LINING,BLADE BLADE LINING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BLADE LINING IS FABRICATED, EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BCGCD 18TYPE,ATTACHMENT,BOARD BOARD ATTACHMENT TYPE INDICATES THE TYPE OF BOARD ATTACHMENT PROVIDED. SELECT REPLY CODE 10AB47 BCGDA 10SPEED IN RPM AT FULL CURRENT OUTPUT,MINIMUM,ARMATURE ARMATURE MINIMUM SPEED IN RPM AT FULL CURRENT OUTPUT THE MINIMUM SPEED THE ARMATURE CAN REVOLVE AND MAINTAIN FULL CURRENT OUTPUT,EXPRESSED IN REVOLUTIONS PER MINUTE. 1A MODE REPLY 0 BCGFB 10CURRENT RATING IN AMPS,OUTPUT,MAXIMUM MAXIMUM OUTPUT CURRENT RATING IN AMPS THE MAXIMUM AMOUNT OF OUTPUT CURRENT FOR WHICH THE ITEM IS RATED,EXPRESSED IN AMPERES. 1B MODE REPLY 0 BCGGA 10SPEED IN RPM,CUT-IN,MINIMUM CURRENT MINIMUM CURRENT CUT-IN SPEED IN RPM THE CUT-IN SPEED NECESSARY TO MAINTAIN A MINIMUM CURRENT FLOW,EXPRESSED IN REVOLUTIONS PER MINUTE. 1A MODE REPLY 0 BCGHJ 04LENGTH,CORD TO CORD,BLADE BLADE CORD TO CORD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BLADE BETWEEN THE CORD CENTERS,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BCGJJ /D/ 04WIDTH,OVERALL,BLADE BLADE OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BLADE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BCGKJ /D/ 04THICKNESS,OVERALL,BLADE BLADE OVERALL THICKNESS AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF A BLADE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BCGLJ 04LENGTH FOR WHICH DESIGNED LENGTH FOR WHICH DESIGNED A MEASUREMENT OF THE LONGEST DIMENSION FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BCGMD 08LOCATION,RECTIFIER RECTIFIER LOCATION INDICATES THE LOCATION OF THE RECTIFIER FOR THE ITEM. SELECT REPLY CODE 10AJ91 BCGND 11METHOD,GROUNDING GROUNDING METHOD THE MEANS BY WHICH THE ITEM IS GROUNDED. SELECT REPLY CODE 10AC58 BCGPJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR AND LOCATION,HOLE,MOUNTING MOUNTING HOLE THREAD SIZE AND SERIES/TYPE DESIGNATOR AND LOCATION DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE MOUNTING HOLE,AND ITS LOCATION. 2D AND 1A MODE REPLY22AH063AJ91 BCGQJ /D/A13THREAD CLASS AND LOCATION,HOLE,MOUNTING MOUNTING HOLE THREAD CLASS AND LOCATION A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL MOUNTING HOLE THREAD,AND ITS LOCATION. 1D AND 1A MODE REPLY13AJ91 BCGRH /D/ 13THREAD DIRECTION AND LOCATION,HOLE,MOUNTING MOUNTING HOLE THREAD DIRECTION AND LOCATION THE DIRECTION OF THE MOUNTING HOLE THREAD WHEN VIEWED AXIALLY,AND ITS LOCATION. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. 2D MODE REPLY 23AA383AJ91 BCGSL 16STYLE,END,SHAFT DRIVE SHAFT DRIVE END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SHAFT DRIVE END. 1L MODE REPLY 0 BCGTD /D/ 07HOLE,PIN,COTTER COTTER PIN HOLE AN INDICATION OF WHETHER OR NOT A COTTER PIN HOLE IS INCLUDED. SELECT REPLY CODE 10AA49 BCGWJ 04DISTANCE FROM RAISED FACE TO FIRST MOUNTING HOLE CENTER DISTANCE FROM RAISED FACE TO FIRST MOUNTING HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 BCGXJ 04DISTANCE FROM SHAFT CENTERLINE TO MOUNTING FLANGE SURFACE DISTANCE FROM SHAFT CENTERLINE TO MOUNTING FLANGE SURFACE NONE. 2D AND 1B MODE REPLY21AA051AC20 BCGYD 18TYPE,DEVICE,SIGHTING SIGHTING DEVICE TYPE INDICATES THE TYPE OF SIGHTING DEVICE PROVIDED. SELECT REPLY CODE 10AD54 BCGZD /D/ 07DEVICE,SETTING,COURSE COURSE SETTING DEVICE AN INDICATION OF WHETHER OR NOT A COURSE SETTING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 BCHBD /D/ 07MIRR0R,COVER COVER MIRROR AN INDICATION OF WHETHER OR NOT A MIRROR IS PROVIDED WITH THE COVER. SELECT REPLY CODE 10AB22 BCHCA 12QUANTITY,LEVEL LEVEL QUANTITY THE NUMBER OF LEVEL(S) PROVIDED. 1A MODE REPLY 0 BCHDD 18TYPE,LEVEL LEVEL TYPE INDICATES THE TYPE OF LEVEL PROVIDED. SELECT REPLY CODE 10AM15 BCHFB /D/ 04ANGLE IN DEG,TANGENT,CENTER CENTER TANGENT ANGLE IN DEG NONE. 1B MODE REPLY 0 BCHGD 14SHAPE,BOWL BOWL SHAPE THE PHYSICAL CONFIGURATION OF THE BOWL. SELECT REPLY CODE 10AD07 BCHHD 18TYPE,ELEMENT,BOWL BOWL ELEMENT TYPE INDICATES THE TYPE OF BOWL ELEMENT PROVIDED. SELECT REPLY CODE 10AK54 BCHJJ 04SIZE,CARD CARD SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE CARD. 1D AND 1B MODE REPLY11AA05 BCHKJ 04SIZE,DIAL DIAL SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE DIAL. 1D AND 1B MODE REPLY11AA05 BCHLJ 04DIAMETER,OUTSIDE,GIMBAL RING GIMBAL RING OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GIMBAL RING,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BCHMD /D/ 07FEATURE,COMPENSATING COMPENSATING FEATURE AN INDICATION OF WHETHER OR NOT A COMPENSATING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BCHND 18TYPE,COMPENSATOR COMPENSATOR TYPE INDICATES THE TYPE OF COMPENSATOR PROVIDED. SELECT REPLY CODE 10AK54 BCHPD /D/ 07CORRECTORS,HEELING HEELING CORRECTORS AN INDICATION OF WHETHER OR NOT HEELING CORRECTORS ARE PROVIDED. SELECT REPLY CODE 10AB22 BCHQJ 04DIAMETER,SURFACE,UPPER BOWL BEARING UPPER BOWL BEARING SURFACE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE UPPER BOWL BEARING SURFACE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BCHRJ 10INCREMENT IN DEG,SMALLEST SMALLEST INCREMENT IN DEG THE SMALLEST VALUE BETWEEN MARKINGS ON AN ITEM,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY12AG46 BCHSD 18TYPE,TRANSMISSION TRANSMISSION TYPE INDICATES THE TYPE OF TRANSMISSION PROVIDED. SELECT REPLY CODE 10AJ53 BCHTA 12QUANTITY,POST,TERMINAL TERMINAL POST QUANTITY THE NUMBER OF TERMINAL POST(S) PROVIDED. 1A MODE REPLY 0 BCHWJ 10WEIGHT,ROTOR ROTOR WEIGHT A RELATIVE MEASURE OF THE MASS OF A ROTOR WITH RESPECT TO ITS DENSITY. 1D AND 1B MODE REPLY12AG67 BCHXB 10SPEED IN RPM,ROTOR ROTOR SPEED IN RPM THE SPEED OF THE ROTOR,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 BCHYD 19FUNCTION,ROTOR ROTOR FUNCTION THE FUNCTION FOR WHICH THE ROTOR WAS DESIGNED. SELECT REPLY CODE 10AC00 BCHZD 07CHARACTERISTIC,PENDULOUS PENDULOUS CHARACTERISTIC AN INDICATION OF THE PENDULOUS CHARACTERISTIC OF THE ITEM. SELECT REPLY CODE 10AM89 BCJBD /D/ 11METHOD,CORRECTION,SPEED/LATITUDE SPEED/LATITUDE CORRECTION METHOD THE MEANS USED TO CORRECT THE SPEED AND LATITUDE OF AN ITEM. SELECT REPLY CODE 10AL28 BCJCD /D/ 07FEATURE,STABILIZING STABILIZING FEATURE AN INDICATION OF WHETHER OR NOT A STABILIZING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BCJDJ 04DIAMETER,CONNECTION CONNECTION DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CONNECTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BCJFD 18TYPE,PROTECTOR,THREAD THREAD PROTECTOR TYPE INDICATES THE TYPE OF THREAD PROTECTOR PROVIDED. SELECT REPLY CODE 10AB26 BCJGD /D/ 07VALVES,METERING METERING VALVES AN INDICATION OF WHETHER OR NOT METERING VALVES ARE PROVIDED. SELECT REPLY CODE 10AB22 BCJHF T10RANGE IN DEG,ALTITUDE ALTITUDE RANGE IN DEG THE ALTITUDE RANGE OF THE ITEM,EXPRESSED IN DEGREES. 1F MODE REPLY 0 BCJJD 18TYPE,DEVICE,AVERAGING AVERAGING DEVICE TYPE INDICATES THE TYPE OF AVERAGING DEVICE PROVIDED. SELECT REPLY CODE 10AK54 BCJKB 10TIME IN MINUTES,OPERATING OPERATING TIME IN MINUTES THE PERIOD OF ELAPSED TIME DURING WHICH THE ITEM WILL OPERATE,EXPRESSED IN MINUTES. 1B MODE REPLY 0 BCJLD /D/ 07FEATURE,ILLUMINATED,ARTIFICIAL HORIZON FIELD ARTIFICIAL HORIZON FIELD ILLUMINATED FEATURE AN INDICATION OF WHETHER OR NOT AN ARTIFICIAL HORIZON FIELD ILLUMINATED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BCJMD /D/ 07SOURCE,POWER,EXTERNAL EXTERNAL POWER SOURCE AN INDICATION OF WHETHER OR NOT AN EXTERNAL POWER SOURCE IS PROVIDED. SELECT REPLY CODE 10AB22 BCJND /D/ 07PROVISION,USE,NATURAL HORIZON NATURAL HORIZON USE PROVISION AN INDICATION OF WHETHER OR NOT PROVISIONS FOR USE OF NATURAL HORIZON ARE PROVIDED. SELECT REPLY CODE 10AB22 BCJPD /D/ 07FEATURE,PERISCOPIC PERISCOPIC FEATURE AN INDICATION OF WHETHER OR NOT A PERSICOPIC FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BCJQJ 04DIAMETER,TUBE TUBE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BCJRD 18TYPE,ELEMENT,DIRECTION SENSING DIRECTION SENSING ELEMENT TYPE INDICATES THE TYPE OF DIRECTION SENSING ELEMENT PROVIDED. SELECT REPLY CODE 10AJ77 BCJSJ 10VOLTAGE IN VOLTS,COIL,TRANSMITTING TRANSMITTING COIL VOLTAGE IN VOLTS THE TOTAL ELECTRICAL VOLTAGE OF THE TRANSMITTING COIL,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 BCJTJ 10FREQUENCY IN HERTZ,COIL,TRANSMITTING TRANSMITTING COIL FREQUENCY IN HERTZ THE CYCLES PER SECOND /HERTZ/ OF ALTERNATING CURRENT FOR WHICH THE TRANSMITTING COIL IS DESIGNED. 1D AND 1B MODE REPLY11AC20 BCJWD 18TYPE,CURRENT,GYRO GYRO CURRENT TYPE INDICATES THE TYPE OF CURRENT USED BY THE GYRO,WHETHER ALTERNATING,DIRECT,OR BOTH. SELECT REPLY CODE 10AB62 BCJXJ 10VOLTAGE IN VOLTS,GYRO GYRO VOLTAGE IN VOLTS THE TOTAL ELECTRICAL VOLTAGE OF THE GYRO,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 BCJYJ 10FREQUENCY IN HERTZ,GYRO GYRO FREQUENCY IN HERTZ THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT FOR WHICH THE GYRO IS DESIGNED. 1D AND 1B MODE REPLY11AC20 BCJZD /D/ 07GLAND,WATERTIGHT,ELECTRICAL CONNECTION CABLE ELECTRICAL CONNECTION CABLE WATERTIGHT GLAND AN INDICATION OF WHETHER OR NOT THE ELECTRICAL CONNECTION IS FURNISHED WITH A WATERTIGHT GLAND FOR THE CABLE. SELECT REPLY CODE 10AA55 BCKBA 12QUANTITY,PRONG,CONNECTOR CONNECTOR PRONG QUANTITY THE NUMBER OF CONNECTOR PRONG(S) PROVIDED. 1A MODE REPLY 0 BCKCD /D/ 07SPHERES,QUADRANTAL QUADRANTAL SPHERES AN INDICATION OF WHETHER OR NOT QUADRANTAL SPHERES ARE INCLUDED. SELECT REPLY CODE 10AA49 BCKDB 10CURRENT RATING IN AMPS,DEMAGNETIZING,MAXIMUM MAXIMUM DEMAGNETIZING CURRENT RATING IN AMPS THE MAXIMUM CONTINUOUS DEMAGNETIZING CURRENT WHICH MUST NOT BE EXCEEDED IN ORDER TO AVOID DAMAGE TO THE ITEM,EXPRESSED IN AMPERES. 1B MODE REPLY 0 BCKFJ 04LENGTH,OPENING,COIL COIL OPENING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A COIL OPENING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BCKGD 18TYPE,FACILITY,READING READING FACILITY TYPE INDICATES THE TYPE OF READING FACILITY PROVIDED. SELECT REPLY CODE 10AJ12 BCKHJ 04WIDTH,OPENING,COIL COIL OPENING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A COIL OPENING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BCKJJ 04HEIGHT,OPENING,COIL COIL OPENING HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A COIL OPENING,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BCKKJ 04DIAMETER,OPENING,COIL COIL OPENING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COIL OPENING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BCKLJ 04LENGTH,SURFACE SURFACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SURFACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BCKMJ 04WIDTH,SURFACE SURFACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A SURFACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BCKNJ 04HEIGHT,SURFACE SURFACE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A SURFACE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BCKPJ 04DEPTH,SURFACE SURFACE DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON A SURFACE,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BCKQD /D/ 07TIMER,CYCLE,AUTOMATIC AUTOMATIC CYCLE TIMER AN INDICATION OF WHETHER OR NOT AN AUTOMATIC CYCLE TIMER IS INCLUDED. SELECT REPLY CODE 10AA49 BCKRJ 10CYCLE,DUTY DUTY CYCLE THE WORKING PERIOD UNDER WHICH THE ITEM IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY13AK72 BCKSJ 10CAPACITY,VERTICAL VERTICAL CAPACITY A MEASUREMENT OF THE VERTICAL CAPACITY OF AN ITEM. 1D AND 1B MODE REPLY11AA05 BCKTJ 10REACH,HORIZONTAL HORIZONTAL REACH A MEASUREMENT OF THE HORIZONTAL DISTANCE THAT THE ITEM CAN REACH. 1D AND 1B MODE REPLY11AA05 BCKWD 18TYPE,READING,INDICATOR INDICATOR READING TYPE INDICATES THE TYPE OF READING PROVIDED BY THE INDICATOR. SELECT REPLY CODE 10AK54 BCKXD 02DESIGN,INDICATOR INDICATOR DESIGN THE DESIGN OF THE INDICATOR. SELECT REPLY CODE 10AJ12 BCKYD /D/ 07TANKS,INSERT INSERT TANKS AN INDICATION OF WHETHER OR NOT INSERT TANKS ARE INCLUDED. SELECT REPLY CODE 10AA49 BCKZD /D/ 07COMPARTMENTS,BUILT-IN BUILT-IN COMPARTMENTS AN INDICATION OF WHETHER OR NOT BUILT-IN COMPARTMENTS ARE INCLUDED. SELECT REPLY CODE 10AA49 BCLBJ 10CAPACITY,COMPARTMENT COMPARTMENT CAPACITY THE AMOUNT OF LIQUID,GRANULES,AND THE LIKE,THE COMPARTMENT WILL HOLD. 1D AND 1B MODE REPLY12AG67 BCLCD /D/ 07PARTITIONS,REMOVABLE REMOVABLE PARTITIONS AN INDICATION OF WHETHER OR NOT REMOVABLE PARTITIONS ARE INCLUDED. SELECT REPLY CODE 10AA49 BCLDD /D/ 07ACCOMMODATION,FILM,DENTAL DENTAL FILM ACCOMMODATION AN INDICATION OF WHETHER OR NOT THE ITEM PROVIDES AN ACCOMMODATION FOR DENTAL FILM. SELECT REPLY CODE 10AB22 BCLFJ B04SIZE ACCOMMODATED,FILM,MAXIMUM MAXIMUM FILM SIZE ACCOMMODATED THE MAXIMUM FILM SIZE THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1F MODE REPLY11AA05 BCLGD /D/ 07FEATURE,CONTROL,AUTOMATIC AUTOMATIC CONTROL FEATURE AN INDICATION OF WHETHER OR NOT AN AUTOMATIC CONTROL FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BCLHD /D/ 07FRAME/BASE FRAME/BASE AN INDICATION OF WHETHER OR NOT A FRAME AND/OR BASE IS PROVIDED. SELECT REPLY CODE 10AB22 BCLJD /D/ 07CONNECTIONS,PLUMBING PLUMBING CONNECTIONS AN INDICATION OF WHETHER OR NOT PLUMBING CONNECTIONS ARE INCLUDED. SELECT REPLY CODE 10AA49 BCLKD /D/ 07REGULATOR,FLOW,WATER WATER FLOW REGULATOR AN INDICATION OF WHETHER OR NOT A WATER FLOW REGULATOR IS INCLUDED. SELECT REPLY CODE 10AA49 BCLLD /D/ 07BRACKETS,HANGER HANGER BRACKETS AN INDICATION OF WHETHER OR NOT HANGER BRACKETS ARE INCLUDED. SELECT REPLY CODE 10AA49 BCLMD 18TYPE,MESH MESH TYPE INDICATES THE TYPE OF MESH PROVIDED. SELECT REPLY CODE 10AE99 BCLNG /D/ 03DESIGNATION,SIZE/SIEVE,MESH MESH SIZE/SIEVE DESIGNATION AN INDICATION OF THE MESH SIZE AND/OR SIEVE DESIGNATION. FULL TEXT WRITE-IN 0 BCLPD 14SHAPE,HOLE HOLE SHAPE THE PHYSICAL CONFIGURATION OF THE HOLE. SELECT REPLY CODE 10AD07 BCLQD 19CHARACTERISTIC,HEIGHT,SIEVE SIEVE HEIGHT CHARACTERISTIC AN INDICATION OF THE SIEVE HEIGHT CHARACTERISTIC. SELECT REPLY CODE 10AF84 BCLRJ /D/ 04DEPTH FROM FRAME TOP TO PERFORATED PORTION DEPTH FROM FRAME TOP TO PERFORATED PORTION A MEASUREMENT FROM THE TOP OF THE FRAME TO THE PERFORATED PORTION,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BCLSD 18TYPE,INPUT INPUT TYPE INDICATES THE TYPE OF INPUT(S) PROVIDED. SELECT REPLY CODE 10AK74 BCLTA /D/ 12QUANTITY,INPUT INPUT QUANTITY THE NUMBER OF INPUTS PROVIDED. PLEASE USE MRC AYYL IN PLACE OF THIS DISCONTINUED MRC. 1A MODE REPLY 0 BCLWJ 10LEVEL RATING,OUTPUT OUTPUT LEVEL RATING AN INDICATION OF THE RATED OUTPUT LEVEL OF AN ITEM. 2D AND 1B MODE REPLY22AB491AC20 BCLXD /D/ 07FEATURE,LEVEL,CONTINUOUSLY VARIABLE CONTINUOUSLY VARIABLE LEVEL FEATURE AN INDICATION OF WHETHER OR NOT A CONTINUOUSLY VARIABLE LEVEL FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BCLYJ 04DISTANCE BETWEEN SHAFT CENTER AND BOTTOM MOUNTING HOLE CENTER DISTANCE BETWEEN SHAFT CENTER AND BOTTOM MOUNTING HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 BCLZJ 04DISTANCE BETWEEN SHAFT CENTER AND TOP MOUNTING HOLE CENTER DISTANCE BETWEEN SHAFT CENTER AND TOP MOUNTING HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 BCMBB 10DEVIATION OF FIRST HOLE FROM TOP CENTER IN DEG,ANGULAR ANGULAR DEVIATION OF FIRST HOLE FROM TOP CENTER IN DEG NONE. 1B MODE REPLY 0 BCMCB 10DEVIATION OF SECOND HOLE FROM FIRST HOLE IN DEG,ANGULAR ANGULAR DEVIATION OF SECOND HOLE FROM FIRST HOLE IN DEG NONE. 1B MODE REPLY 0 BCMDJ 04DISTANCE BETWEEN INSIDE SURFACES OF HINGE BRACKET DISTANCE BETWEEN INSIDE SURFACES OF HINGE BRACKET NONE. 2D AND 1B MODE REPLY21AA051AC20 BCMFJ 04DISTANCE BETWEEN OUTSIDE SURFACES OF HINGE BRACKET DISTANCE BETWEEN OUTSIDE SURFACES OF HINGE BRACKET NONE. 2D AND 1B MODE REPLY21AA051AC20 BCMGJ 04DIAMETER,HOLE,TOP MOUNTING TOP MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BCMHJ 04DIAMETER,HOLE,BOTTOM MOUNTING BOTTOM MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BCMJJ 04DISTANCE BETWEEN TOP MOUNTING SLOT AND BOTTOM MOUNTING HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN TOP MOUNTING SLOT AND BOTTOM MOUNTING HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BCMKJ 04DISTANCE FROM RAISED FACE TO SECOND MOUNTING CENTER DISTANCE FROM RAISED FACE TO SECOND MOUNTING CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 BCMLB 10DEVIATION OF THIRD HOLE FROM SECOND HOLE IN DEG,ANGULAR ANGULAR DEVIATION OF THIRD HOLE FROM SECOND HOLE IN DEG NONE. 1B MODE REPLY 0 BCMMB 10DEVIATION OF FOURTH HOLE FROM THIRD HOLE IN DEG,ANGULAR ANGULAR DEVIATION OF FOURTH HOLE FROM THIRD HOLE IN DEG NONE. 1B MODE REPLY 0 BCMNB /D/ 10DEVIATION OF FIFTH HOLE FROM FOURTH HOLE IN DEG,ANGULAR ANGULAR DEVIATION OF FIFTH HOLE FROM FOURTH HOLE IN DEG NONE. 1B MODE REPLY 0 BCMPJ 04DIAMETER,LARGEST,MOUNTING HOLE MOUNTING HOLE LARGEST DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BCMQJ 04DIAMETER,SMALLEST,MOUNTING HOLE MOUNTING HOLE SMALLEST DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BCMRJ 04DIAMETER,OUTSIDE,MOUNTING PILOT MOUNTING PILOT OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BCMSJ 04DISTANCE FROM MOUNTING HOLE CENTER TO END OF HOUSING DISTANCE FROM MOUNTING HOLE CENTER TO END OF HOUSING NONE. 2D AND 1B MODE REPLY21AA051AC20 BCMTJ 04DEPTH,MOUNTING PILOT MOUNTING PILOT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BCMWJ 04DISTANCE FROM END TO FIRST KEYWAY CENTER DISTANCE FROM END TO FIRST KEYWAY CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 BCMXJ 04WIDTH,KEYWAY,FIRST FIRST KEYWAY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BCMYJ 04LENGTH,KEYWAY,FIRST FIRST KEYWAY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BCMZJ 04DISTANCE FROM END TO SECOND KEYWAY CENTER DISTANCE FROM END TO SECOND KEYWAY CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 BCNBJ 04LENGTH,KEYWAY,SECOND SECOND KEYWAY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BCNCJ 04WIDTH,KEYWAY,SECOND SECOND KEYWAY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BCNDA 10SPEED IN RPM,ARMATURE,MAXIMUM RATED MAXIMUM RATED ARMATURE SPEED IN RPM THE SPEED THE ARMATURE CAN REVOLVE AND PRODUCE MAXIMUM CURRENT,EXPRESSED IN REVOLUTIONS PER MINUTE. 1A MODE REPLY 0 BCNFJ 04THICKNESS FOR WHICH DESIGNED THICKNESS FOR WHICH DESIGNED A MEASUREMENT OF THE SMALLEST DIMENSION FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BCNGJ 04LENGTH,OVERALL,HEAD HEAD OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE HEAD. 2D AND 1B MODE REPLY21AA051AC20 BCNHD 11METHOD,FORMING,LETTER LETTER FORMING METHOD THE MEANS BY WHICH THE LETTER(S) IS FORMED. SELECT REPLY CODE 10AM90 BCNJD 02DESIGN,CHARACTER CHARACTER DESIGN THE DESIGN OF THE CHARACTER ON THE ITEM. SELECT REPLY CODE 10AF91 BCNKD /D/ 07TRACK TRACK AN INDICATION OF WHETHER OR NOT A TRACK IS INCLUDED. SELECT REPLY CODE 10AA49 BCNLD /D/ 07MARK,PUNCTUATION PUNCTUATION MARK AN INDICATION OF WHETHER OR NOT A PUNCTUATION MARK(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BCNMD 18TYPE FOR WHICH DESIGNED,LETTERING LETTERING TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF LETTERING FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BCNND /D/ 19WIDTH FOR WHICH DESIGNED,LETTERING LETTERING WIDTH FOR WHICH DESIGNED AN INDICATION OF THE WIDTH OF LETTERING FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BCNPD 18TYPE,SCRIBER,ANGLE ANGLE SCRIBER TYPE INDICATES THE TYPE OF ANGLE SCRIBER PROVIDED. SELECT REPLY CODE 10AK54 BCNQA 12QUANTITY,GUIDE,LETTERING LETTERING GUIDE QUANTITY THE NUMBER OF LETTERING GUIDE(S) PROVIDED. 1A MODE REPLY 0 BCNRJ 04HEIGHT,CHARACTER,UPPER CASE UPPER CASE CHARACTER HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE UPPER CASE CHARACTER,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BCNSJ 04HEIGHT,CHARACTER,LOWER CASE LOWER CASE CHARACTER HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE LOWER CASE CHARACTER,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BCNTJ 04HEIGHT,NUMERAL NUMERAL HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE NUMERAL. 1D AND 1B MODE REPLY11AA05 BCNWD /D/ 07GROOVE,SCRIBER,INTEGRAL INTEGRAL SCRIBER GROOVE AN INDICATION OF WHETHER OR NOT AN INTEGRAL SCRIBER GROOVE IS INCLUDED. SELECT REPLY CODE 10AA49 BCNXD 18TYPE FOR WHICH DESIGNED,MOUNTING MOUNTING TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF MOUNTING FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AM39 BCNYA 12QUANTITY,WHEEL,TRAILER TRAILER WHEEL QUANTITY THE NUMBER OF WHEELS INCLUDED ON THE TRAILER. 1A MODE REPLY 0 BCNZD 18TYPE,WHEEL,TRAILER TRAILER WHEEL TYPE INDICATES THE TYPE OF WHEEL(S) PROVIDED ON THE TRAILER. SELECT REPLY CODE 10AH67 BCPBD /D/ 07FEATURE,DESIGN,PUSH PUSH DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A PUSH DESIGN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BCPCJ /D/ 10SIZE,MAGNET MAGNET SIZE A MEASUREMENT OF THE SURFACE OF A MAGNET. 2D AND 1B MODE REPLY21AA051AC20 BCPDD 18TYPE,CURRENT,GENERATOR GENERATOR CURRENT TYPE INDICATES THE TYPE OF CURRENT OF THE GENERATOR,WHETHER ALTERNATING,DIRECT,OR BOTH. SELECT REPLY CODE 10AB62 BCPFG /D/ 10WATTAGE RATING IN WATTS,GENERATOR GENERATOR WATTAGE RATING IN WATTS THE RATED POWER THAT A GENERATOR CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS. FULL TEXT WRITE-IN 0 BCPGB 10VOLTAGE IN VOLTS,GENERATOR GENERATOR VOLTAGE IN VOLTS THE TOTAL ELECTRICAL VOLTAGE OF THE GENERATOR,EXPRESSED IN VOLTS. 1B MODE REPLY 0 BCPHG 19NAME,MANUFACTURER,GENERATOR GENERATOR MANUFACTURER NAME THE NAME OF THE MANUFACTURER OF THE GENERATOR. FULL TEXT WRITE-IN 0 BCPJG /D/ 19ADDRESS,MANUFACTURER,GENERATOR GENERATOR MANUFACTURER ADDRESS THE ADDRESS OF THE MANUFACTURER OF THE GENERATOR. FULL TEXT WRITE-IN 0 BCPKA 19NUMBER,IDENTIFYING,GENERATOR MANUFACTURER GENERATOR MANUFACTURER IDENTIFYING NUMBER THE NUMBER USED BY THE MANUFACTURER FOR IDENTIFYING THE GENERATOR. 1A MODE REPLY 0 BCPLD 19SOURCE,POWER,GENERATOR GENERATOR POWER SOURCE THE POWER SOURCE INCLUDED WITH THE GENERATOR. SELECT REPLY CODE 10AJ13 BCPMG 19NAME,MANUFACTURER,POWER UNIT POWER UNIT MANUFACTURER NAME THE NAME OF THE MANUFACTURER OF THE POWER UNIT. FULL TEXT WRITE-IN 0 BCPNG /D/ 19ADDRESS,MANUFACTURER,POWER UNIT POWER UNIT MANUFACTURER ADDRESS THE ADDRESS OF THE MANUFACTURER OF THE POWER UNIT. FULL TEXT WRITE-IN 0 BCPPA 19NUMBER,IDENTIFYING,POWER UNIT MANUFACTURER POWER UNIT MANUFACTURER IDENTIFYING NUMBER THE NUMBER USED BY THE MANUFACTURER FOR IDENTIFYING THE POWER UNIT. 1A MODE REPLY 0 BCPQG /D/ 03DESIGNATOR,NUMBER/TYPE,PAGE PAGE NUMBER/TYPE DESIGNATOR THE PAGE NUMBER AND/OR TYPE DESIGNATOR INDICATING THE COMPONENT LISTING OF THE ITEM. FULL TEXT WRITE-IN 0 BCPRD /D/ 02DESIGN,OPERATION,TRACK TRACK OPERATION DESIGN AN INDICATION OF THE TRACK OPERATION FOR WHICH DESIGNED. SELECT REPLY CODE 10AK54 BCPTG /D/ 19EQUIPMENT FOR WHICH DESIGNED EQUIPMENT FOR WHICH DESIGNED THE EQUIPMENT FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 BCPWD 11METHOD,CONTROL,PLOW PLOW CONTROL METHOD THE MEANS BY WHICH THE PLOW IS OPERATED OR CONTROLLED. SELECT REPLY CODE 10AH20 BCPXD 19COVERAGE,EQUIPMENT,TRAINING TRAINING EQUIPMENT COVERAGE AN INDICATION OF THE SCOPE OF EQUIPMENT FOR WHICH TRAINING IS PROVIDED. SELECT REPLY CODE 10AJ98 BCPYD /D/ 11METHOD,RAISING/LOWERING,UNIT UNIT RAISING/LOWERING METHOD THE MEANS USED TO RAISE AND/OR LOWER THE UNIT. SELECT REPLY CODE 10AH20 BCPZJ 04LENGTH,OVERALL,MOLDBOARD MOLDBOARD OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE MOLDBOARD. 2D AND 1B MODE REPLY21AA051AC20 BCQBG 04HEIGHT,MOLDBOARD MOLDBOARD HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE MOLDBOARD,IN DISTINCTION FROM DEPTH. FULL TEXT WRITE-IN 0 BCQCD 18TYPE,UNIT,ROTARY POWER ROTARY POWER UNIT TYPE INDICATES THE TYPE OF ROTARY POWER UNIT UTILIZED TO OPERATE THE ITEM. SELECT REPLY CODE 10AJ13 BCQDD /D/ 07WING,MOUNTED,SIDE SIDE MOUNTED WING AN INDICATION OF WHETHER OR NOT A SIDE MOUNTED WING(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BCQFD 18TYPE,WING,SIDE SIDE WING TYPE INDICATES THE TYPE OF WING(S) PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AC58 BCQGD /D/ 18TYPE,ENGINE,ROTOR ROTOR ENGINE TYPE INDICATES THE TYPE OF ROTOR ENGINE UTILIZED ON THE ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AJ13 BCQHG 19NAME,MANUFACTURER,ROTOR ENGINE ROTOR ENGINE MANUFACTURER NAME THE NAME OF THE MANUFACTURER OF THE ROTOR ENGINE. FULL TEXT WRITE-IN 0 BCQJA /D/ 19NUMBER,IDENTIFYING,ROTOR ENGINE MANUFACTURER ROTOR ENGINE MANUFACTURER IDENTIFYING NUMBER THE NUMBER USED BY THE MANUFACTURER FOR IDENTIFYING THE ROTOR ENGINE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1A MODE REPLY 0 BCQKJ 04LENGTH,WING WING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE WING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BCQLD /D/ 08LOCATION FOR WHICH DESIGNED,MOUNTING MOUNTING LOCATION FOR WHICH DESIGNED INDICATES THE MOUNTING LOCATION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AJ91 BCQMD /D/ 07DEVICE,LOADING LOADING DEVICE AN INDICATION OF WHETHER OR NOT A LOADING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 BCQNA 19NUMBER,IDENTIFYING,PRIME MOVER MANUFACTURER PRIME MOVER MANUFACTURER IDENTIFYING NUMBER THE NUMBER USED BY THE MANUFACTURER FOR IDENTIFYING THE PRIME MOVER. 1A MODE REPLY 0 BCQPG 18TYPE,CHASSIS,PRIME MOVER PRIME MOVER CHASSIS TYPE INDICATES THE TYPE OF CHASSIS PROVIDED WITH THE PRIME MOVER. FULL TEXT WRITE-IN 0 BCQQD /D/ 18TYPE,BODY,PRIME MOVER PRIME MOVER BODY TYPE INDICATES THE TYPE OF BODY PROVIDED WITH THE PRIME MOVER. SELECT REPLY CODE 10AE98 BCQRJ 10CAPACITY,MOVER,PRIME PRIME MOVER CAPACITY AN INDICATION OF THE CAPACITY OF THE PRIME MOVER. 2D AND 1B MODE REPLY22AG671AC20 BCQSJ 10WEIGHT,GROSS,PRIME MOVER PRIME MOVER GROSS WEIGHT THE TOTAL WEIGHT OF THE PRIME MOVER FULLY EQUIPPED. 1D AND 1B MODE REPLY12AG67 BCQTD 18TYPE,ENGINE,PRIME MOVER PRIME MOVER ENGINE TYPE INDICATES THE TYPE OF ENGINE UTILIZED BY THE PRIME MOVER. SELECT REPLY CODE 10AJ13 BCQWG /D/ 19NUMBER,MODEL,CONVEYANCE CONVEYANCE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE CONVEYANCE. FULL TEXT WRITE-IN 0 BCQXA /D/ 19NATIONAL STOCK NUMBER,CONVEYANCE CONVEYANCE NATIONAL STOCK NUMBER THE NATIONAL STOCK NUMBER ASSIGNED TO THE CONVEYANCE. 1A MODE REPLY 0 BCQYD 18TYPE FOR WHICH DESIGNED,AIRCRAFT AIRCRAFT TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF AIRCRAFT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AM91 BCQZG /D/ 19NUMBER,MODEL,AIRCRAFT AIRCRAFT MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE AIRCRAFT. FULL TEXT WRITE-IN 0 BCRBD 11METHOD,LAUNCHING,MISSILE MISSILE LAUNCHING METHOD THE MEANS PROVIDED FOR MISSILE LAUNCHING. SELECT REPLY CODE 10AL78 BCRCD /D/ 07CAPABILITY,JETTISON JETTISON CAPABILITY AN INDICATION OF WHETHER OR NOT A JETTISON CAPABILITY IS INCLUDED. SELECT REPLY CODE 10AA49 BCRDD /D/ 07CAPABILITY,JETTISON,MISSILE MISSILE JETTISON CAPABILITY AN INDICATION OF WHETHER OR NOT A MISSILE JETTISON CAPABILITY IS INCLUDED. SELECT REPLY CODE 10AA49 BCRFJ T04SIZE RANGE ACCOMMODATED,PIPE PIPE SIZE RANGE ACCOMMODATED A MEASUREMENT OF THE MINIMUM TO MAXIMUM PIPE SIZE THE ITEM WILL ACCOMMODATE. 1D AND 1F MODE REPLY11AA05 BCRGD 18TYPE,SLOT SLOT TYPE INDICATES THE TYPE OF SLOT PROVIDED. SELECT REPLY CODE 10AG25 BCRHA 12QUANTITY,SPINDLE SPINDLE QUANTITY THE NUMBER OF SPINDLES PROVIDED. 1A MODE REPLY 0 BCRJJ /D/ 04DISTANCE BETWEEN OUTSIDE SPINDLE CENTERS,MAXIMUM MAXIMUM DISTANCE BETWEEN OUTSIDE SPINDLE CENTERS THE MAXIMUM DISTANCE BETWEEN THE CENTERS OF THE OUTSIDE SPINDLES. 1D AND 1B MODE REPLY11AA05 BCRKJ /D/ 04DISTANCE BETWEEN OUTSIDE SPINDLE CENTERS,MINIMUM MINIMUM DISTANCE BETWEEN OUTSIDE SPINDLE CENTERS THE MINIMUM DISTANCE BETWEEN THE CENTERS OF THE OUTSIDE SPINDLE. 1D AND 1B MODE REPLY11AA05 BCRLJ 04SIZE ACCOMMODATED,CHISEL,MAXIMUM MAXIMUM CHISEL SIZE ACCOMMODATED DESIGNATES THE MAXIMUM CHISEL SIZE THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BCRMJ T10RANGE,STROKE,CHISEL RAM CHISEL RAM STROKE RANGE A MEASUREMENT OF THE MINIMUM TO MAXIMUM LIMITS OF THE RAM STROKE OF THE CHISEL. 1D AND 1F MODE REPLY11AA05 BCRNJ 04DISTANCE FROM TABLE TO VERTICAL CHISEL END,MAXIMUM MAXIMUM DISTANCE FROM TABLE TO VERTICAL CHISEL END THE MAXIMUM DISTANCE FROM THE TABLE TO THE END OF THE VERTICAL CHISEL. 1D AND 1B MODE REPLY11AA05 BCRPJ /D/ 04DISTANCE FROM TABLE TO HORIZONTAL CHISEL CENTERLINE,MAXIMUM MAXIMUM DISTANCE FROM TABLE TO HORIZONTAL CHISEL CENTERLINE THE MAXIMUM DISTANCE FROM THE TABLE TO THE CENTERLINE OF THE HORIZONTAL CHISEL. 1D AND 1B MODE REPLY11AA05 BCRQJ 04DISTANCE FROM FENCE TO CHISEL CENTER,MAXIMUM MAXIMUM DISTANCE FROM FENCE TO CHISEL CENTER THE MAXIMUM DISTANCE FROM THE FENCE TO THE CENTER OF THE CHISEL. 1D AND 1B MODE REPLY11AA05 BCRRJ 04DISTANCE,TABLE ADJUSTMENT,VERTICAL VERTICAL TABLE ADJUSTMENT DISTANCE THE DISTANCE OF THE VERTICAL TABLE ADJUSTMENT. 2D AND 1B MODE REPLY21AA051AC20 BCRSJ 04DISTANCE,HORIZONTAL TABLE ADJUSTMENT HORIZONTAL TABLE ADJUSTMENT DISTANCE THE DISTANCE OF THE HORIZONTAL TABLE ADJUSTMENT. 2D AND 1B MODE REPLY21AA051AC20 BCRTJ 04DISTANCE,ADJUSTMENT,CROSS TABLE CROSS TABLE ADJUSTMENT DISTANCE THE DISTANCE OF THE CROSS TABLE ADJUSTMENT. 2D AND 1B MODE REPLY21AA051AC20 BCRWB 10ADJUSTMENT IN DEG,TABLE,ANGULAR ANGULAR TABLE ADJUSTMENT IN DEG A MEASUREMENT OF THE ANGULAR TABLE ADJUSTMENT,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BCRXD 03DESIGNATION,ASA SPINDLE NOSE TYPE ASA SPINDLE NOSE TYPE DESIGNATION THE AMERICAN STANDARD ASSOCIATION DESIGNATION WHICH IDENTIFIES THE NOSE TYPE OF THE SPINDLE USED WITH THE ITEM. SELECT REPLY CODE 10AK54 BCRYJ 04DIAMETER,SPINDLE,THREADED THREADED SPINDLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED SPINDLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BCRZJ 04DIAMETER,SHOULDER,CENTERING CENTERING SHOULDER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CENTERING SHOULDER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BCSBJ 04LENGTH,NOSE,SPINDLE SPINDLE NOSE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SPINDLE NOSE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BCSCD 07ADAPTER,MOUNTING MOUNTING ADAPTER AN INDICATION OF WHETHER OR NOT A MOUNTING ADAPTER IS REQUIRED. SELECT REPLY CODE 10AE40 BCSDD 02DESIGN,SCREW SCREW DESIGN THE DESIGN OF THE SCREW. SELECT REPLY CODE 10AK54 BCSFG 19NAME,SPINDLE,ASA ASA SPINDLE NAME THE AMERICAN STANDARD ASSOCIATION NAME BY WHICH THE SPINDLE IS IDENTIFIED. FULL TEXT WRITE-IN 0 BCSGD /D/ 18TYPE,SCREW SCREW TYPE INDICATES THE TYPE OF SCREW PROVIDED. SELECT REPLY CODE 10AE98 BCSHJ /D/ 04LENGTH FROM END OF HUB TO FACE OF GEAR LENGTH FROM END OF HUB TO FACE OF GEAR NONE. 2D AND 1B MODE REPLY21AA051AC20 BCSJJ /D/ 04DEPTH FROM FACE OF TEETH TO END OF HUB DEPTH FROM FACE OF TEETH TO END OF HUB NONE. 2D AND 1B MODE REPLY21AA051AC20 BCSKJ /D/ 04DISTANCE FROM FACE OF GEAR TO FACE OF FLANGE DISTANCE FROM FACE OF GEAR TO FACE OF FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BCSLJ /D/ 04DISTANCE FROM FIRST END HUB END TO FACE OF GEAR DISTANCE FROM FIRST END HUB END TO FACE OF GEAR NONE. 2D AND 1B MODE REPLY21AA051AC20 BCSMJ /D/ 04DISTANCE FROM SECOND END HUB END TO FACE OF GEAR DISTANCE FROM SECOND END HUB END TO FACE OF GEAR NONE. 2D AND 1B MODE REPLY21AA051AC20 BCSNJ /D/ 04DEPTH FROM FIRST END FACE OF TEETH TO FACE OF BORE DEPTH FROM FIRST END FACE OF TEETH TO FACE OF BORE NONE. 2D AND 1B MODE REPLY21AA051AC20 BCSPJ /D/ 04DEPTH FROM SECOND END FACE OF TEETH TO FACE OF BORE DEPTH FROM SECOND END FACE OF TEETH TO FACE OF BORE NONE. 2D AND 1B MODE REPLY21AA051AC20 BCSQJ /D/ 04DEPTH FROM FIRST END FACE OF TEETH TO HUB END DEPTH FROM FIRST END FACE OF TEETH TO HUB END NONE. 2D AND 1B MODE REPLY21AA051AC20 BCSRJ /D/ 04DEPTH FROM SECOND END FACE OF TEETH TO HUB END DEPTH FROM SECOND END FACE OF TEETH TO HUB END NONE. 2D AND 1B MODE REPLY21AA051AC20 BCSSJ /D/ 04DEPTH FROM PITCH LINE TO BOTTOM OF RACK DEPTH FROM PITCH LINE TO BOTTOM OF RACK NONE. 2D AND 1B MODE REPLY21AA051AC20 BCSTJ 04LENGTH,BOSS BOSS LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A BOSS,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BCSWD /D/ 09MATERIAL,GUIDE,LETTERING LETTERING GUIDE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LETTERING GUIDE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BCSXA 12QUANTITY,PEN PEN QUANTITY THE NUMBER OF PEN(S) PROVIDED. 1A MODE REPLY 0 BCSYG 12SIZE AND QUANTITY,LINE,PEN PEN LINE SIZE AND QUANTITY DESIGNATES THE LINE SIZE OF THE PEN AND THE NUMBER OF PEN(S) PROVIDED. FULL TEXT WRITE-IN 0 BCSZD /D/ 07SOCKET AND PENHOLDER FOR FREEHAND LETTERING SOCKET AND PENHOLDER FOR FREEHAND LETTERING AN INDICATION OF WHETHER OR NOT A SOCKET AND PENHOLDER FOR FREEHAND LETTERING IS INCLUDED. SELECT REPLY CODE 10AA49 BCTBD 18TYPE,TELESCOPE TELESCOPE TYPE INDICATES THE TYPE OF TELESCOPE PROVIDED. SELECT REPLY CODE 10AD54 BCTCJ 04LENGTH,TELESCOPE TELESCOPE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A TELESCOPE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BCTDD 18TYPE,FOCUSING FOCUSING TYPE INDICATES THE TYPE OF FOCUSING PROVIDED. SELECT REPLY CODE 10AH21 BCTFJ 04DIAMETER MAGNIFYING POWER DIAMETER MAGNIFYING POWER AN INDICATION OF THE NUMBER OF TIMES AN ITEM CAN ENLARGE A DIAMETER. 1D AND 1B MODE REPLY11AC20 BCTGD /D/ 07HAIR,STADIA STADIA HAIR AN INDICATION OF WHETHER OR NOT A STADIA HAIR IS INCLUDED. SELECT REPLY CODE 10AA49 BCTHD /D/ 07LEVEL,STRIDING STRIDING LEVEL AN INDICATION OF WHETHER OR NOT A STRIDING LEVEL IS INCLUDED. SELECT REPLY CODE 10AA49 BCTJJ 10SIZE,APERTURE,EFFECTIVE EFFECTIVE APERTURE SIZE DESIGNATES THE REAL OR TRUE SIZE OF THE OPENING. 2D AND 1B MODE REPLY21AA051AC20 BCTKD /D/ 07TELESCOPE,AUXILIARY AUXILIARY TELESCOPE AN INDICATION OF WHETHER OR NOT AN AUXILIARY TELESCOPE IS INCLUDED. SELECT REPLY CODE 10AA49 BCTLD /D/ 07VIAL,LEVEL,TELESCOPE TELESCOPE LEVEL VIAL AN INDICATION OF WHETHER OR NOT A TELESCOPE LEVEL VIAL IS INCLUDED. SELECT REPLY CODE 10AA49 BCTMA 12QUANTITY,SCREW,LEVELING LEVELING SCREW QUANTITY THE NUMBER OF LEVELING SCREW(S) PROVIDED. 1A MODE REPLY 0 BCTNJ 04DIAMETER,ARC,VERTICAL VERTICAL ARC DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A VERTICAL ARC,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BCTPJ 10UNIT,GRADUATION,ARC,MINIMUM MINIMUM ARC GRADUATION UNIT THE SMALLEST INCREMENT OF MEASURE REPRESENTED BY THE MARKING/S/ ON AN ARC. 1D AND 1B MODE REPLY13AJ40 BCTQJ 10UNIT,GRADUATION,VERNIER,MINIMUM MINIMUM VERNIER GRADUATION UNIT THE SMALLEST INCREMENT OF MEASURE REPRESENTED BY THE MARKING/S/ ON A VERNIER. 1D AND 1B MODE REPLY13AJ40 BCTRA 12QUANTITY,EDGE,BEVELED,BLADE BLADE BEVELED EDGE QUANTITY THE NUMBER OF BEVELED EDGE(S) PROVIDED ON THE BLADE. 1A MODE REPLY 0 BCTSD /D/ 07GRADUATIONS,BLADE BLADE GRADUATIONS AN INDICATION OF WHETHER OR NOT BLADE GRADUATIONS ARE INCLUDED. SELECT REPLY CODE 10AA49 BCTTJ 10REPRESENTATION,DIVISION DIVISION REPRESENTATION THE DIVISION REPRESENTATION OF A LARGER UNIT OF MEASURE. 1D AND 1B MODE REPLY12AG67 BCTWD /D/ 07LEVEL,CIRCULAR,BLADE BLADE CIRCULAR LEVEL AN INDICATION OF WHETHER OR NOT A BLADE CIRCULAR LEVEL IS INCLUDED. SELECT REPLY CODE 10AA49 BCTXD /D/ 07COMPASS,TROUGH,BLADE BLADE TROUGH COMPASS AN INDICATION OF WHETHER OR NOT A BLADE TROUGH COMPASS IS INCLUDED. SELECT REPLY CODE 10AA49 BCTYD 19POSITION,MOUNTING,GRADUATED ARC GRADUATED ARC MOUNTING POSITION THE POSITION FOR WHICH THE GRADUATED ARC IS DESIGNED TO MOUNT. SELECT REPLY CODE 10AM84 BCTZD 03DESIGNATION,GRADUATION,ARC ARC GRADUATION DESIGNATION A DESIGNATION INDICATING THE ARC GRADUATION ON THE ITEM. SELECT REPLY CODE 10AM93 BCWBD 03DESIGNATION,GRADUATION,INTERCHANGEABLE ARC INTERCHANGEABLE ARC GRADUATION DESIGNATION A DESIGNATION INDICATING THE INTERCHANGEABLE ARC GRADUATION ON THE ITEM. SELECT REPLY CODE 10AM93 BCWCD /D/ 07VERNIER,ARC,GRADUATED GRADUATED ARC VERNIER AN INDICATION OF WHETHER OR NOT A GRADUATED ARC VERNIER IS INCLUDED. SELECT REPLY CODE 10AA49 BCWDJ /D/ 10UNIT,GRADUATION,ARC VERNIER ARC VERNIER GRADUATION UNIT THE INCREMENT OF MEASURE REPRESENTED BY THE MARKING/S/ ON THE ARC VERNIER. 1D AND 1B MODE REPLY13AJ40 BCWFG 19SENSITIVITY,LEVEL,SPIRIT SPIRIT LEVEL SENSITIVITY THE SENSITIVITY TO WHICH A SPIRIT LEVEL RESPONDS TO A CHANGE IN ITS POSITION. FULL TEXT WRITE-IN 0 BCWGD /D/ 07CIRCLE,HORIZONTAL HORIZONTAL CIRCLE AN INDICATION OF WHETHER OR NOT A HORIZONTAL CIRCLE IS INCLUDED. SELECT REPLY CODE 10AA49 BCWHJ 04DIAMETER,CIRCLE,HORIZONTAL HORIZONTAL CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HORIZONTAL CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BCWJD 19INSCRIPTION,UNIT OF MEASURE,HORIZONTAL CIRCLE HORIZONTAL CIRCLE UNIT OF MEASURE INSCRIPTION THE UNIT OF VALUATION AS REPRESENTED BY THE INSCRIPTION ON THE HORIZONTAL CIRCLE. SELECT REPLY CODE 10AJ40 BCWKD /D/ 07VERNIER,CIRCLE,HORIZONTAL HORIZONTAL CIRCLE VERNIER AN INDICATION OF WHETHER OR NOT A HORIZONTAL CIRCLE VERNIER IS INCLUDED. SELECT REPLY CODE 10AA49 BCWLA 12QUANTITY,VERNIER,HORIZONTAL CIRCLE HORIZONTAL CIRCLE VERNIER QUANTITY THE NUMBER OF HORIZONTAL CIRCLE VERNIER(S) PROVIDED. 1A MODE REPLY 0 BCWMJ 10UNIT,GRADUATION,HORIZONTAL CIRCLE VERNIER HORIZONTAL CIRCLE VERNIER GRADUATION UNIT THE INCREMENT OF MEASURE REPRESENTED BY THE MARKING/S/ ON THE HORIZONTAL CIRCLE VERNIER. 1D AND 1B MODE REPLY13AJ40 BCWNJ 10UNIT,GRADUATION,MINIMUM,HORIZONTAL CIRCLE HORIZONTAL CIRCLE MINIMUM GRADUATION UNIT THE SMALLEST INCREMENT OF MEASURE REPRESENTED BY THE MARKING/S/ ON THE HORIZONTAL CIRCLE. 1D AND 1B MODE REPLY13AJ40 BCWPD /D/ 07CIRCLE,VERTICAL VERTICAL CIRCLE AN INDICATION OF WHETHER OR NOT A VERTICAL CIRCLE IS INCLUDED. SELECT REPLY CODE 10AA49 BCWQJ 10UNIT,GRADUATION,VERTICAL CIRCLE MINIMUM VERNIER VERTICAL CIRCLE MINIMUM VERNIER GRADUATION UNIT THE SMALLEST INCREMENT OF MEASURE REPRESENTED BY THE MARKING/S/ ON THE VERTICAL CIRCLE VERNIER. 1D AND 1B MODE REPLY13AJ40 BCWRJ 10UNIT,GRADUATION,VERTICAL CIRCLE MINIMUM VERTICAL CIRCLE MINIMUM GRADUATION UNIT THE SMALLEST INCREMENT OF MEASURE REPRESENTED BY THE MARKING/S/ ON THE VERTICAL CIRCLE. 1D AND 1B MODE REPLY13AJ40 BCWSD /D/ 07GRADUATION,ARC,STADIA,VERTICAL CIRCLE VERTICAL CIRCLE STADIA ARC GRADUATION AN INDICATION OF WHETHER OR NOT A VERTICAL CIRCLE STADIA ARC GRADUATION IS INCLUDED. SELECT REPLY CODE 10AA49 BCWTD 18TYPE FOR WHICH DESIGNED,MISSILE MISSILE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF MISSILE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AM92 BCWWA 12QUANTITY ACCOMMODATED,MISSILE MISSILE QUANTITY ACCOMMODATED THE NUMBER OF MISSILES THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 BCWXD 07ADJUSTABILITY,POSITION,LAUNCHING LAUNCHING POSITION ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE LAUNCHING POSITION IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BCWYJ /D/ 10RANGE,ELEVATION ELEVATION RANGE THE LIMITS OF ELEVATION FROM THE HORIZONTAL PLANE. 2D AND 1B MODE REPLY22AB491AC20 BCWZA 19SYMBOL,COMPLIANCE,BOX,INTERSTATE COMMERCE COMMISSION INTERSTATE COMMERCE COMMISSION BOX COMPLIANCE SYMBOL THE INTERSTATE COMMERCE COMMISSION SYMBOL INDICATING THE STANDARD TO WHICH THE BOX COMPLIES. 1A MODE REPLY 0 BCXBJ 04DEPTH,OUTSIDE OUTSIDE DEPTH AN OUTSIDE MEASUREMENT BETWEEN SPECIFIED POINTS ON AN ITEM,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BCXCA /D/ 19SYMBOL,COMPLIANCE,BOX,GOVERNMENT GOVERNMENT BOX COMPLIANCE SYMBOL THE GOVERNMENT SYMBOL INDICATING THE STANDARD TO WHICH THE BOX COMPLIES. 1A MODE REPLY 0 BCXDJ 04DIAMETER,INSIDE,BORE BORE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR BORE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BCXFD 14SHAPE,HOLE,BOLT BOLT HOLE SHAPE THE PHYSICAL CONFIGURATION OF THE BOLT HOLE. SELECT REPLY CODE 10AD07 BCXGA 12QUANTITY,CRYSTAL,FIXED FIXED CRYSTAL QUANTITY THE NUMBER OF FIXED CRYSTALS ON THE ITEM. 1A MODE REPLY 0 BCXHA 12QUANTITY,READING,TIME DIFFERENCE TIME DIFFERENCE READING QUANTITY THE NUMBER OF READINGS REQUIRED TO OBTAIN TIME DIFFERENCE. 1A MODE REPLY 0 BCXJA 12QUANTITY,SELECTION,REPETITION RATE REPETITION RATE SELECTION QUANTITY THE NUMBER OF REPETITION RATES THAT CAN BE SELECTED. 1A MODE REPLY 0 BCXKG 04SIZE,HOLE,BOLT BOLT HOLE SIZE DESIGNATES THE SIZE OF THE BOLT HOLE/S/ ON THE ITEM. FULL TEXT WRITE-IN 0 BCXLG /D/ 04DISTANCE BETWEEN BOLT HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES THE CENTER TO CENTER DISTANCE BETWEEN THE BOLT HOLES. FULL TEXT WRITE-IN 0 BCXMD 18TYPE,GRIP,HAND HAND GRIP TYPE INDICATES THE TYPE OF HAND GRIP PROVIDED ON THE ITEM. SELECT REPLY CODE 10AD28 BCXND /D/ 18TYPE,EMISSION,TRANSMITTER TRANSMITTER EMISSION TYPE INDICATES A CLASSIFICATION OF RADIO FREQUENCY EMISSIONS IN WHICH THE TYPE OF MODULATION,TRANSMISSION,AND/OR SUPPLEMENTARY CHARACTERISTICS ARE REPRESENTED BY SYMBOLS. SELECT REPLY CODE 10AJ76 BCXPD /D/ 18TYPE,EMISSION,RECEIVER RECEIVER EMISSION TYPE INDICATES A CLASSIFICATION OF RADIO FREQUENCY EMISSIONS IN WHICH THE TYPE OF MODULATION,TRANSMISSION,AND/OR SUPPLEMENTARY CHARACTERISTICS ARE REPRESENTED BY SYMBOLS. SELECT REPLY CODE 10AJ76 BCXQD /D/ 07FEATURE,LOCKING LOCKING FEATURE AN INDICATION OF WHETHER OR NOT A LOCKING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BCXRD 18TYPE,CONNECTION,CORE PROCESSED END CORE PROCESSED END CONNECTION TYPE INDICATES THE TYPE OF PROCESSED END CONNECTION PROVIDED. SELECT REPLY CODE 10AB76 BCXSD /D/ 07CHANNEL,GUARD GUARD CHANNEL AN INDICATION OF WHETHER OR NOT A GUARD CHANNEL IS INCLUDED. SELECT REPLY CODE 10AA49 BCXTD /D/ 07FEATURE,TUNING,AUXILIARY BANDSPREAD AUXILIARY BANDSPREAD TUNING FEATURE AN INDICATION OF WHETHER OR NOT AN AUXILIARY BANDSPREAD TUNING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BCXWD /D/ 07UNIT,TUNING,PLUG-IN PLUG-IN TUNING UNIT AN INDICATION OF WHETHER OR NOT A PLUG-IN TUNING UNIT/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BCXXJ /D/ 04LENGTH,EXPOSED,CORE CORE EXPOSED LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE EXPOSED PORTION OF THE CORE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BCXYD /D/ 09MATERIAL,CONDUIT,FLEXIBLE FLEXIBLE CONDUIT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FLEXIBLE CONDUIT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BCXZG /D/ 19SPEC/STD,MATERIAL,FLEXIBLE CONDUIT FLEXIBLE CONDUIT MATERIAL SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE FLEXIBLE CONDUIT BASIC MATERIAL. FULL TEXT WRITE-IN 0 BCYBD /D/ 17SURFACE TREATMENT,CONDUIT,FLEXIBLE FLEXIBLE CONDUIT SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE FLEXIBLE CONDUIT. SELECT REPLY CODE 10AD09 BCYCD /D/ 07INDICATOR,INTEGRAL INTEGRAL INDICATOR AN INDICATION OF WHETHER OR NOT AN INTEGRAL INDICATOR IS INCLUDED. SELECT REPLY CODE 10AA49 BCYDJ 04DIAMETER,OUTSIDE,FLEXIBLE CONDUIT FLEXIBLE CONDUIT OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FLEXIBLE CONDUIT,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BCYFD /D/ 07ADAPTER,MOUNTING,THREADED THREADED MOUNTING ADAPTER AN INDICATION OF WHETHER OR NOT A THREADED MOUNTING ADAPTER IS INCLUDED. SELECT REPLY CODE 10AA49 BCYGJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,ADAPTER ADAPTER THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED ADAPTER. 1D AND 1A MODE REPLY12AH06 BCYHJ 13THREAD LENGTH,ADAPTER ADAPTER THREAD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE EXTENT OF ADAPTER THREADS,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BCYJD /D/ 07SHOULDER,MOUNTING,FIXED FIXED MOUNTING SHOULDER AN INDICATION OF WHETHER OR NOT A FIXED (NONADJUSTABLE) MOUNTING SHOULDER IS INCLUDED. SELECT REPLY CODE 10AA49 BCYKJ 04DISTANCE,TRAVEL TRAVEL DISTANCE THE DISTANCE AN ITEM IS DESIGNED TO TRAVEL FROM ITS FULLY RETRACTED TO ITS FULLY EXTENDED POSITION. 2D AND 1B MODE REPLY21AA051AC20 BCYLD /D/ 07PROVISION,ADJUSTMENT,ROTARY ROTARY ADJUSTMENT PROVISION AN INDICATION OF WHETHER OR NOT A PROVISION FOR ROTARY ADJUSTMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BCYMJ 04LENGTH ACROSS ARMS LENGTH ACROSS ARMS A MEASUREMENT OF THE LONGEST DIMENSION OF A STRAIGHT LINE WHICH EXTENDS FROM THE EXTREME END OF ONE ARM TO THE EXTREME END OF THE OPPOSITE ARM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BCYNJ 04DIAMETER,ARM ARM DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR ARM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BCYPJ /D/ 10VOLTAGE RATING,AC,POWER SOURCE POWER SOURCE AC VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,OF ALTERNATING CURRENT POTENTIAL FOR WHICH THE POWER SOURCE IS RATED. 2D AND 1B MODE REPLY21AB631AC20 BCYQJ /D/ 10VOLTAGE RATING,DC,POWER SOURCE POWER SOURCE DC VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,OF DIRECT CURRENT POTENTIAL FOR WHICH THE POWER SOURCE IS RATED. 2D AND 1B MODE REPLY21AB631AC20 BCYRD 19VEHICLE FOR WHICH DESIGNED VEHICLE FOR WHICH DESIGNED THE VEHICLE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AH21 BCYSD /D/ 11METHOD,PASSAGE,ARM LUBRICANT ARM LUBRICANT PASSAGE METHOD THE MEANS PROVIDED ON THE ARM FOR LUBRICANT PASSAGE. SELECT REPLY CODE 10AK60 BCYTD 11METHOD,CORRECTION,PARALLAX PARALLAX CORRECTION METHOD THE MEANS USED FOR PARALLAX CORRECTION OF AN ITEM. SELECT REPLY CODE 10AK73 BCYWJ /D/ 10FREQUENCY RATING,MULTIPLEXING MULTIPLEXING FREQUENCY RATING THE NUMBER OF MULTIPLEXING COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE ITEM IS RATED. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AC321AC20 BCYXG 19TITLE,PROGRAM PROGRAM TITLE AN INDICATION OF THE PROGRAM TITLE. FULL TEXT WRITE-IN 0 BCYYD /D/ 09MATERIAL,REEL REEL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE REEL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BCYZJ 04DIAMETER,OVERALL,ARBOR ARBOR OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF AN ARBOR. 2D AND 1B MODE REPLY21AA051AC20 BCZBJ 04DIAMETER,INSIDE,CENTER HOLE CENTER HOLE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CENTER HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BCZCD /D/ 07RING,PROTECTION,FILE FILE PROTECTION RING AN INDICATION OF WHETHER OR NOT A FILE PROTECTION RING IS INCLUDED. SELECT REPLY CODE 10AA49 BCZDA 12QUANTITY,CHARACTER CHARACTER QUANTITY THE NUMBER OF CHARACTERS PROVIDED. 1A MODE REPLY 0 BCZFD /D/ 07FEATURE,MOUNTED,CASH DRAWER CASH DRAWER MOUNTED FEATURE AN INDICATION OF WHETHER OR NOT A CASH DRAWER MOUNTED FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BCZGD /D/ 07COMPARTMENT,COPY,LOCK-IN LOCK-IN COPY COMPARTMENT AN INDICATION OF WHETHER OR NOT A LOCK-IN COPY COMPARTMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BCZHJ B04SIZE ACCOMMODATED,FORM FORM SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE FORM ACCOMMODATED. 1D AND 1F MODE REPLY11AA05 BCZJA 10CAPACITY,COLLATING,SHEET SHEET COLLATING CAPACITY THE AMOUNT OF SHEETS THE ITEM WILL COLLATE. 1A MODE REPLY 0 BCZKD 18TYPE,ASSEMBLY,TRAY TRAY ASSEMBLY TYPE INDICATES THE TYPE OF TRAY ASSEMBLY PROVIDED. SELECT REPLY CODE 10AK54 BCZLD /D/ 07TRAY,COMBINATION COMBINATION TRAY AN INDICATION OF WHETHER OR NOT A COMBINATION TRAY IS INCLUDED. SELECT REPLY CODE 10AA49 BCZMJ B04SIZE,TRAY TRAY SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE TRAY. 1D AND 1F MODE REPLY11AA05 BCZNJ 10CAPACITY,TRAY TRAY CAPACITY A MEASUREMENT OF THE AMOUNT THE TRAY WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BCZPJ 10MEASUREMENT RATING,FREQUENCY FREQUENCY MEASUREMENT RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE FREQUENCY MEASUREMENT IS RATED. 2D AND 1B MODE REPLY21AC321AC20 BCZRJ A10CAPABILITY,SPACING,LINE LINE SPACING CAPABILITY THE NUMBER OF LINES WHICH THE ITEM IS CAPABLE OF PRINTING IN A GIVEN HORIZONTAL OR VERTICAL POSITION. 1D AND 1A MODE REPLY11AB39 BCZSD /D/ 18TYPE,CUTOFF,TAPE END TAPE END CUTOFF TYPE INDICATES THE TYPE OF TAPE END CUTOFF PROVIDED. SELECT REPLY CODE 10AK54 BCZTD /D/ 07PUNCH,HOLE HOLE PUNCH AN INDICATION OF WHETHER OR NOT A HOLE PUNCH IS INCLUDED. SELECT REPLY CODE 10AA49 BCZWD 18TYPE FOR WHICH DESIGNED,TAPE TAPE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF TAPE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL63 BCZXJ 04WIDTH ACCOMMODATED,STRIP STRIP WIDTH ACCOMMODATED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE STRIP THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BCZYD 02DESIGN,IMPRESSION,CHARACTER CHARACTER IMPRESSION DESIGN AN INDICATION OF THE CHARACTER IMPRESSION THE ITEM IS DESIGNED TO PRODUCE. SELECT REPLY CODE 10AL59 BCZZD /D/ 08LOCATION,HOLE,MOUNTING MOUNTING HOLE LOCATION INDICATES THE LOCATION OF THE MOUNTING HOLE(S) IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 BDBBJ 04HEIGHT,CHARACTER CHARACTER HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE CHARACTER,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BDBCD 11METHOD,READING,CHARACTER CHARACTER READING METHOD THE MEANS BY WHICH THE CHARACTERS ARE READ. SELECT REPLY CODE 10AF63 BDBDD /D/ 07WHEEL,CHARACTER CHARACTER WHEEL AN INDICATION OF WHETHER OR NOT A CHARACTER WHEEL IS INCLUDED. SELECT REPLY CODE 10AA49 BDBFA 12QUANTITY,CHARACTER,ALPHABETIC ALPHABETIC CHARACTER QUANTITY THE NUMBER OF ALPHABETIC CHARACTERS PROVIDED. 1A MODE REPLY 0 BDBGG /D/ 10CONDUCTIVITY,THERMAL,MAXIMUM MAXIMUM THERMAL CONDUCTIVITY THE MAXIMUM RATE OF HEAT FLOW THAT PASSES THROUGH A UNIT AREA AT A GIVEN TEMPERATURE. FULL TEXT WRITE-IN 0 BDBHG /D/ 19RANGE,CHARACTER,ALPHABETIC ALPHABETIC CHARACTER RANGE AN INDICATION OF THE ALPHABETIC CHARACTER RANGE. FULL TEXT WRITE-IN 0 BDBJA 12QUANTITY,CHARACTER,NUMERIC NUMERIC CHARACTER QUANTITY THE NUMBER OF NUMERIC CHARACTERS PROVIDED. 1A MODE REPLY 0 BDBKG /D/ 19RANGE,CHARACTER,NUMERIC NUMERIC CHARACTER RANGE AN INDICATION OF THE NUMERIC CHARACTER RANGE. FULL TEXT WRITE-IN 0 BDBLD /D/ 07HOLES,FASTENER FASTENER HOLES AN INDICATION OF WHETHER OR NOT FASTENER HOLES ARE INCLUDED. SELECT REPLY CODE 10AA49 BDBMA 12QUANTITY,SOCKET,TABBING TABBING SOCKET QUANTITY THE NUMBER OF TABBING SOCKETS PROVIDED. 1A MODE REPLY 0 BDBNG 19MARKINGS MARKINGS AN INDICATION OF THE MARKINGS ON THE ITEM. FULL TEXT WRITE-IN 0 BDBPA 03DESIGNATOR,PLATE PLATE DESIGNATOR THE ALPHA AND/OR NUMERIC DESIGNATOR OF THE PLATE. 1A MODE REPLY 0 BDBQJ 04WIDTH,COVERAGE COVERAGE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE AREA THE ITEM IS DESIGNED TO COVER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BDBRJ 04LENGTH,COVERAGE COVERAGE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN AREA THE ITEM IS DESIGNED TO COVER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BDBSL 16STYLE,HEAD,TRIPOD TRIPOD HEAD STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TRIPOD HEAD. 1L MODE REPLY 0 BDBTA 13THREAD SIZE,SCREW,BINDING BINDING SCREW THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE BINDING SCREW. 1A MODE REPLY 0 BDBWD /D/ 19UNIT ON HORIZONTAL/VERTICAL CIRCLE,GRADUATION GRADUATION UNIT ON HORIZONTAL/VERTICAL CIRCLE THE INCREMENT OF MEASURE REPRESENTED BY THE MARKING/S/ ON THE HORIZONTAL AND VERTICAL CIRCLES. SELECT REPLY CODE 10AJ40 BDBXJ 10GRADUATION,MINIMUM MINIMUM GRADUATION THE SMALLEST INCREMENT OF MEASURE REPRESENTED BY THE MARKING(S) ON THE ITEM. 2D AND 1B MODE REPLY23AJ402AM12 BDBYD /D/ 07EYEPIECE,AUTOCOLLIMATION AUTOCOLLIMATION EYEPIECE AN INDICATION OF WHETHER OR NOT AN AUTOCOLLIMATION EYEPIECE IS INCLUDED. SELECT REPLY CODE 10AA49 BDBZD /D/ 07CENTER,DOUBLE DOUBLE CENTER AN INDICATION OF WHETHER OR NOT A DOUBLE CENTER IS PROVIDED. SELECT REPLY CODE 10AB22 BDCBD /D/ 07TRIBRACH,DETACHABLE,HORIZONTAL BASE HORIZONTAL BASE DETACHABLE TRIBRACH AN INDICATION OF WHETHER OR NOT A HORIZONTAL BASE DETACHABLE TRIBRACH IS INCLUDED. SELECT REPLY CODE 10AA49 BDCCD /D/ 07MECHANISM,RELEASE,QUICK,DETACHABLE TRIBRACH DETACHABLE TRIBRACH QUICK RELEASE MECHANISM AN INDICATION OF WHETHER OR NOT A DETACHABLE TRIBRACH QUICK RELEASE MECHANISM IS INCLUDED. SELECT REPLY CODE 10AA49 BDCDD /D/ 07DEVICE,CENTERING,AUTOMATIC,HORIZONTAL BASE HORIZONTAL BASE AUTOMATIC CENTERING DEVICE AN INDICATION OF WHETHER OR NOT A HORIZONTAL BASE AUTOMATIC CENTERING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 BDCFD /D/ 07PLUMB,OPTICAL OPTICAL PLUMB AN INDICATION OF WHETHER OR NOT AN OPTICAL PLUMB IS INCLUDED. SELECT REPLY CODE 10AA49 BDCGD /D/ 07LEVEL,CIRCULAR CIRCULAR LEVEL AN INDICATION OF WHETHER OR NOT A CIRCULAR LEVEL IS INCLUDED. SELECT REPLY CODE 10AA49 BDCHD /D/ 07DEVICE,PLOTTING PLOTTING DEVICE AN INDICATION OF WHETHER OR NOT A PLOTTING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 BDCJD /D/ 07COMPASS COMPASS AN INDICATION OF WHETHER OR NOT A COMPASS IS INCLUDED. SELECT REPLY CODE 10AA49 BDCKH /D/ 09MATERIAL AND TYPE,CONTAINER CONTAINER MATERIAL AND TYPE THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CONTAINER IS FABRICATED,AND THE TYPE. 2D MODE REPLY 26AD092AF72 BDCLD /D/ 09MATERIAL,SURFACE,DISPLAY/PLOTTING DISPLAY/PLOTTING SURFACE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE DISPLAY/PLOTTING SURFACE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BDCMD /D/ 18TYPE,SURFACE,DISPLAY/PLOTTING DISPLAY/PLOTTING SURFACE TYPE INDICATES THE TYPE OF DISPLAY/PLOTTING SURFACE PROVIDED. SELECT REPLY CODE 10AK92 BDCNG 19INSCRIPTION,SURFACE SURFACE INSCRIPTION THE INSCRIPTION AFFIXED TO OR STAMPED ON THE SURFACE OF THE ITEM. FULL TEXT WRITE-IN 0 BDCPD 14SHAPE,SURFACE SURFACE SHAPE THE PHYSICAL CONFIGURATION OF THE SURFACE. SELECT REPLY CODE 10AD07 BDCQJ 10AREA,SURFACE,USABLE USABLE SURFACE AREA A MEASUREMENT OF THE AREA OF USABLE SURFACE. 1D AND 1B MODE REPLY12AG67 BDCRD 08LOCATION,DISPLAY,INSCRIBED INSCRIBED DISPLAY LOCATION INDICATES THE LOCATION OF THE INSCRIBED DISPLAY ON THE ITEM. SELECT REPLY CODE 10AJ91 BDCSD 07TOOL,SPECIAL MARKING SPECIAL MARKING TOOL AN INDICATION OF WHETHER OR NOT A SPECIAL MARKING TOOL IS REQUIRED. SELECT REPLY CODE 10AE40 BDCTD 18TYPE,TOOL,SPECIAL MARKING SPECIAL MARKING TOOL TYPE INDICATES THE TYPE OF SPECIAL MARKING TOOL PROVIDED. SELECT REPLY CODE 10AM94 BDCWD /D/ 07FACILITY,LIGHTING LIGHTING FACILITY AN INDICATION OF WHETHER OR NOT A LIGHTING FACILITY(IES) IS INCLUDED. SELECT REPLY CODE 10AA49 BDCXD /D/ 07SYNCHRO,INDICATOR INDICATOR SYNCHRO AN INDICATION OF WHETHER OR NOT AN INDICATOR SYNCHRO IS INCLUDED. SELECT REPLY CODE 10AA49 BDCYJ 10VOLTAGE RATING,SYNCHRO,INDICATOR INDICATOR SYNCHRO VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,FOR WHICH THE INDICATOR SYNCHRO IS RATED. 2D AND 1B MODE REPLY21AB631AC20 BDCZJ 10FREQUENCY RATING,SYNCHRO,INDICATOR INDICATOR SYNCHRO FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE INDICATOR SYNCHRO IS RATED. 2D AND 1B MODE REPLY21AC321AC20 BDDBD 14SHAPE,VIEW,PLAN PLAN VIEW SHAPE THE PHYSICAL CONFIGURATION OF THE PLAN WHEN VIEWED FROM THE TOP. SELECT REPLY CODE 10AD07 BDDCD 18TYPE,FACET FACET TYPE INDICATES THE TYPE OF FACET PROVIDED. SELECT REPLY CODE 10AH83 BDDDA 10RATIO,MAP MAP RATIO THE MAXIMUM TO MINIMUM MAP RATIO,WITH THE LARGER RELATIVE PROPORTION GIVEN,THE LOWER VALUE HAVING AN IMPLIED (NOT GIVEN) VALUE OF ONE (UNIT). 1A MODE REPLY 0 BDDFJ 04LENGTH,GRADUATION GRADUATION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A GRADUATION,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BDDGG 10CALIBRATION,DECIMAL DECIMAL CALIBRATION AN INDICATION OF THE MANNER IN WHICH THE ITEM IS CALIBRATED IN DECIMALS. FULL TEXT WRITE-IN 0 BDDHD 18TYPE,SCALE,DECIMAL DECIMAL SCALE TYPE INDICATES THE TYPE OF DECIMAL SCALE PROVIDED. SELECT REPLY CODE 10AM12 BDDJG 10CALIBRATION,REPRESENTATION,FRACTIONAL FRACTIONAL REPRESENTATION CALIBRATION AN INDICATION OF THE UNIT OF MEASURE REPRESENTED BY THE FRACTIONAL CALIBRATION(S) OF THE ITEM. FULL TEXT WRITE-IN 0 BDDKD 18TYPE,SCALE,FRACTIONAL FRACTIONAL SCALE TYPE INDICATES THE TYPE OF FRACTIONAL SCALE PROVIDED. SELECT REPLY CODE 10AM12 BDDLG 10CALIBRATION,METRIC METRIC CALIBRATION AN INDICATION OF THE MANNER IN WHICH THE ITEM IS METRICALLY CALIBRATED. FULL TEXT WRITE-IN 0 BDDMD 18TYPE,SCALE,METRIC METRIC SCALE TYPE INDICATES THE TYPE OF METRIC SCALE PROVIDED. SELECT REPLY CODE 10AM12 BDDND 08LOCATION,EDGE,STRAIGHT STRAIGHT EDGE LOCATION INDICATES THE LOCATION OF THE STRAIGHT EDGE. SELECT REPLY CODE 10AJ91 BDDPD /D/ 18TYPE,FORM,EDGE EDGE FORM TYPE INDICATES THE TYPE OF EDGE FORM PROVIDED. SELECT REPLY CODE 10AD07 BDDQD /D/ 07FEATURE,DESIGN,DRAFTING MACHINE DRAFTING MACHINE DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A DRAFTING MACHINE DESIGN FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BDDRJ 04THICKNESS,HUB HUB THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE HUB,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BDDSJ 04DIAMETER,BORE,HUB HUB BORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR HUB BORE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BDDTJ /D/ 04DIAMETER,SURFACE,BEARING,ARM ARM BEARING SURFACE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ARM BEARING SURFACE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BDDWJ /D/ 04LENGTH,SURFACE,BEARING,ARM ARM BEARING SURFACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ARM BEARING SURFACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BDDXD /D/ 14SHAPE,BEARING BEARING SHAPE THE PHYSICAL CONFIGURATION OF THE BEARING. SELECT REPLY CODE 10AD07 BDDYA 12QUANTITY,BEARING BEARING QUANTITY THE NUMBER OF BEARINGS PROVIDED ON THE ITEM. 1A MODE REPLY 0 BDDZJ /D/ 04DIAMETER,OUTSIDE,BEARING BEARING OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BEARING,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BDFBJ /D/ 04LENGTH,BEARING BEARING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A BEARING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BDFCD 19MODE,LUBRICATION LUBRICATION MODE THE MEANS OF LUBRICATION APPLIED TO THE ITEM. SELECT REPLY CODE 10AM95 BDFDD /D/ 08LOCATION,LUBRICATION LUBRICATION LOCATION INDICATES THE LOCATION OF THE LUBRICANT ON THE ITEM. SELECT REPLY CODE 10AJ91 BDFFD /D/ 07PROVISION,THREAD,PORT PORT THREAD PROVISION AN INDICATION OF WHETHER OR NOT THE PORT IS THREADED. SELECT REPLY CODE 10AE00 BDFGD /D/ 07BORE,FULCRUM FULCRUM BORE AN INDICATION OF WHETHER OR NOT A FULCRUM BORE IS PROVIDED. SELECT REPLY CODE 10AB22 BDFHD /D/ 07SHAFT,FULCRUM FULCRUM SHAFT AN INDICATION OF WHETHER OR NOT A FULCRUM SHAFT IS INCLUDED. SELECT REPLY CODE 10AA49 BDFJD /D/ 07HUB,SPLIT,FULCRUM FULCRUM SPLIT HUB AN INDICATION OF WHETHER OR NOT THE FULCRUM IS PROVIDED WITH A SPLIT HUB. SELECT REPLY CODE 10AB22 BDFKD /D/ 07HOLE,THREADED THREADED HOLE AN INDICATION OF WHETHER OR NOT A THREADED HOLE(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BDFLA 13THREAD SIZE,HOLE HOLE THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED HOLE. 1A MODE REPLY 0 BDFMJ 04DIAMETER,HOLE,UNTHREADED UNTHREADED HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BDFNJ 04DIAMETER,INSIDE,BEARING BEARING INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BEARING,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BDFPD /D/ 07ACCOMMODATION,FITTING,LUBRICATION LUBRICATION FITTING ACCOMMODATION AN INDICATION OF WHETHER OR NOT AN ACCOMMODATION/S/ IS PROVIDED FOR LUBRICATION FITTINGS. SELECT REPLY CODE 10AB22 BDFQD /D/ 07SPRING SPRING AN INDICATION OF WHETHER OR NOT A SPRING(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BDFRG 04SIZE,FACE FACE SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE FACE. FULL TEXT WRITE-IN 0 BDFSA 12QUANTITY,TURN,COIL COIL TURN QUANTITY THE NUMBER OF COIL TURNS PROVIDED. 1A MODE REPLY 0 BDFTJ 10RESISTANCE,DC,COIL COIL DC RESISTANCE THE OPPOSITION THAT THE COIL OFFERS TO THE FLOW OF DIRECT CURRENT. 2D AND 1B MODE REPLY21AA571AC20 BDFWD /D/ 07WINDOW,DIAL DIAL WINDOW AN INDICATION OF WHETHER OR NOT A DIAL WINDOW IS INCLUDED. SELECT REPLY CODE 10AA49 BDFXD /D/ 07FRAME,DIAL DIAL FRAME AN INDICATION OF WHETHER OR NOT A DIAL FRAME IS INCLUDED. SELECT REPLY CODE 10AA49 BDFYD 18TYPE,PROVISION,SUPPLY SUPPLY PROVISION TYPE INDICATES THE TYPE OF SUPPLY PROVISION INCLUDED. SELECT REPLY CODE 10AC58 BDFZA /D/ 12QUANTITY,FACILITY,CONNECTION,TERMINAL TERMINAL CONNECTION FACILITY QUANTITY THE NUMBER OF TERMINAL CONNECTION FACILITY(IES) PROVIDED ON THE ITEM. 1A MODE REPLY 0 BDGBD 18TYPE,FACILITY,CONNECTION CONNECTION FACILITY TYPE INDICATES THE TYPE OF FACILITY(IES) PROVIDED TO CONNECT THE ITEM. SELECT REPLY CODE 10AB76 BDGCG /D/ 04SIZE/D/,FACILITY,CONNECTION CONNECTION FACILITY SIZE/D/ DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE CONNECTION FACILITY(IES). FULL TEXT WRITE-IN 0 BDGDG /D/ 19CONFIGURATION,FACILITY,CONNECTION CONNECTION FACILITY CONFIGURATION THE NARRATIVE EXPRESSION USED FOR INDICATING THE CONFIGURATION OF THE CONNECTION FACILITY/IES/. FULL TEXT WRITE-IN 0 BDGFA /D/ 12QUANTITY,SLOT,BARRIER BARRIER SLOT QUANTITY THE NUMBER OF BARRIER SLOT(S) INCLUDED IN THE ITEM. 1A MODE REPLY 0 BDGGG /D/ 04SIZE/D/,SLOT,BARRIER BARRIER SLOT SIZE/D/ DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE BARRIER SLOT(S). FULL TEXT WRITE-IN 0 BDGHG /D/ 19CONFIGURATION,SPACING,BARRIER SLOT BARRIER SLOT SPACING CONFIGURATION THE NARRATIVE EXPRESSION USED FOR INDICATING THE SPACING CONFIGURATION OF THE BARRIER SLOT/S/. FULL TEXT WRITE-IN 0 BDGJJ 04WIDTH,GAP,AIR AIR GAP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE AIR GAP,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BDGKJ 10DENSITY,FLUX FLUX DENSITY A MEASUREMENT OF THE ELECTROMAGNETIC LINES OF FORCE. 2D AND 1B MODE REPLY22AG671AC20 BDGLJ 04DISTANCE FROM RADIAL CENTER TO FLAT SURFACE DISTANCE FROM RADIAL CENTER TO FLAT SURFACE THE DISTANCE FROM THE RADIAL CENTER TO THE FLAT SURFACE OF AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 BDGMJ 04LENGTH,SERRATION SERRATION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SERRATION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BDGND /D/ 07HOLE,THREADED,LINK END LINK END THREADED HOLE AN INDICATION OF WHETHER OR NOT A LINK END THREADED HOLE/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 BDGPD /D/ 07FEATURE,CLAMPING,SPLIT END SCREW SPLIT END SCREW CLAMPING FEATURE AN INDICATION OF WHETHER OR NOT A SPLIT END SCREW CLAMPING FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BDGQA /D/ 13THREAD SIZE,HOLE,CLAMPING SCREW CLAMPING SCREW HOLE THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE CLAMPING SCREW HOLE. 1A MODE REPLY 0 BDGRJ 04LENGTH,OVERALL,BRUSH BRUSH OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BRUSH. 2D AND 1B MODE REPLY21AA051AC20 BDGSD 07ADJUSTABILITY,DIRECTION,BRUSH SWEEP BRUSH SWEEP DIRECTION ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE BRUSH SWEEP DIRECTION IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BDGTD 05DIRECTION FOR WHICH DESIGNED,SWEEP SWEEP DIRECTION FOR WHICH DESIGNED THE DIRECTION FOR WHICH THE ITEM IS DESIGNED TO SWEEP. SELECT REPLY CODE 10AL96 BDGWD /D/ 07BRUSH,SIDE SIDE BRUSH AN INDICATION OF WHETHER OR NOT A SIDE BRUSH(ES) IS INCLUDED. SELECT REPLY CODE 10AA49 BDGXD 08LOCATION,BRUSH BRUSH LOCATION INDICATES THE LOCATION OF THE BRUSH ON THE ITEM. SELECT REPLY CODE 10AJ91 BDGYD /D/ 07FEATURE,PICK UP,REFUSE REFUSE PICK UP FEATURE AN INDICATION OF WHETHER OR NOT A REFUSE PICK UP FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BDGZJ 04DIAMETER,BRUSH BRUSH DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BRUSH,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BDHBJ 10CAPACITY,HOPPER HOPPER CAPACITY THE RATED LOAD THE HOPPER WILL ACCOMMODATE. 2D AND 1B MODE REPLY22AG671AC20 BDHCD /D/ 07SYSTEM,SPRAY,WATER WATER SPRAY SYSTEM AN INDICATION OF WHETHER OR NOT A WATER SPRAY SYSTEM IS INCLUDED. SELECT REPLY CODE 10AA49 BDHDD 18TYPE,ATTACHMENT ATTACHMENT TYPE INDICATES THE TYPE OF ATTACHMENT PROVIDED. SELECT REPLY CODE 10AJ74 BDHFJ A18TYPE AND QUANTITY,MALLET MALLET TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF MALLET(S) FURNISHED. 1D AND 1A MODE REPLY13AK95 BDHGD /D/ 07CONTROL,LINE,AUTOMATIC INTERMITTENT AUTOMATIC INTERMITTENT LINE CONTROL AN INDICATION OF WHETHER OR NOT AN AUTOMATIC INTERMITTENT LINE CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 BDHHJ 04WIDTH,MINIMUM,MARKING LINE MARKING LINE MINIMUM WIDTH THE MINIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MARKING LINE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BDHJG /D/ 10CAPACITY AND QUANTITY,TANK TANK CAPACITY AND QUANTITY AN INDICATION OF THE TANK CAPACITY AND NUMBER OF EACH ON THE ITEM. FULL TEXT WRITE-IN 0 BDHKG /D/ 19CAPABILITY,STRIPING STRIPING CAPABILITY AN INDICATION OF THE STRIPING CAPABILITY OF THE ITEM. FULL TEXT WRITE-IN 0 BDHLJ 04WIDTH,MAXIMUM,MARKING LINE MARKING LINE MAXIMUM WIDTH THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MARKING LINE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BDHMJ 10RESISTANCE IN OHMS RESISTANCE IN OHMS A MEASUREMENT OF THE OPPOSITION TO THE FLOW OF CURRENT,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AB39 BDHNG 08LOCATION CONFIGURATION,TERMINAL TERMINAL LOCATION CONFIGURATION INDICATES THE CONFIGURATION OF THE TERMINAL LOCATION(S) ON THE ITEM. FULL TEXT WRITE-IN 0 BDHPD /D/ 17SURFACE TREATMENT,BACKING BACKING SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE BACKING. SELECT REPLY CODE 10AD09 BDHQA 19FACTOR,MULTIPLICATION MULTIPLICATION FACTOR THE NUMBER BY WHICH A READING MUST BE MULTIPLIED TO OBTAIN THE TRUE VALUE. 1A MODE REPLY 0 BDHRD 18TYPE,CALIBRATION CALIBRATION TYPE INDICATES THE TYPE OF CALIBRATION PROVIDED. SELECT REPLY CODE 10AJ14 BDHSG /D/ 10RANGE,CALIBRATION,INSTRUMENT INSTRUMENT CALIBRATION RANGE AN INDICATION OF THE CALIBRATION MEASUREMENT RANGE OF THE INSTRUMENT. FULL TEXT WRITE-IN 0 BDHTA 12QUANTITY,RANGE,CALIBRATION CALIBRATION RANGE QUANTITY THE NUMBER OF CALIBRATION RANGES PROVIDED ON THE ITEM. 1A MODE REPLY 0 BDHWG 10ACCURACY RATING,CALIBRATION CALIBRATION ACCURACY RATING THE DEGREE OF CONFORMITY OF A MEASUREMENT TO A STANDARD OR TRUE VALUE FOR WHICH THE CALIBRATION IS RATED. FULL TEXT WRITE-IN 0 BDHXG 19CONTROL,EXTERNAL EXTERNAL CONTROL THE MEANS USED TO EXTERNALLY CONTROL THE ITEM. FULL TEXT WRITE-IN 0 BDHYD /D/ 07LINE,DELAY DELAY LINE AN INDICATION OF WHETHER OR NOT A DELAY LINE IS INCLUDED. SELECT REPLY CODE 10AA49 BDHZB 10AMPLITUDE IN VOLTS,SIGNAL,OUTPUT OUTPUT SIGNAL AMPLITUDE IN VOLTS THE GREATEST VALUE OF THE CURRENT STRENGTH ATTAINED DURING THE CYCLE OF ALTERNATING CURRENT FOR WHICH THE OUTPUT SIGNAL IS RATED,EXPRESSED IN VOLTS. 1B MODE REPLY 0 BDJBB 10AMPLITUDE IN WATTS,SIGNAL,OUTPUT OUTPUT SIGNAL AMPLITUDE IN WATTS THE GREATEST VALUE OF THE CURRENT STRENGTH ATTAINED DURING THE CYCLE OF ALTERNATING CURRENT FOR WHICH THE OUTPUT SIGNAL IS RATED,EXPRESSED IN WATTS. 1B MODE REPLY 0 BDJCJ 10INDUCTANCE RATING INDUCTANCE RATING THE VALUE,OR RANGE OF VALUES,OF INDUCTANCE INHERENT IN THE ITEM. 1D AND 1B MODE REPLY11AC31 BDJDF T10RANGE IN PERCENT,ACCURACY ACCURACY RANGE IN PERCENT THE ACCEPTABLE LIMITS OF DEVIATION FROM THE DESIGNED STANDARD OUTPUT VALUE OF THE ITEM,EXPRESSED IN PERCENT. 1F MODE REPLY 0 BDJFJ T10RANGE,CONNECTION,INDUCTANCE SERIES INDUCTANCE SERIES CONNECTION RANGE THE MINIMUM AND MAXIMUM RATING OF A REACTIVE CURRENT TO THE TOTAL CURRENT IN A SERIES CONNECTION CIRCUIT. 1D AND 1F MODE REPLY11AC31 BDJGF T10ACCURACY IN PERCENT,CONNECTION,INDUCTANCE SERIES INDUCTANCE SERIES CONNECTION ACCURACY IN PERCENT THE ACCEPTABLE LIMITS OF DEVIATION FROM THE INDUCTANCE SERIES CONNECTION DESIGNED STANDARD OUTPUT VALUE,EXPRESSED IN PERCENT. 1F MODE REPLY 0 BDJHJ T10RANGE,CONNECTION,INDUCTANCE PARALLEL INDUCTANCE PARALLEL CONNECTION RANGE THE MINIMUM AND MAXIMUM RATING OF A REACTIVE CURRENT TO THE TOTAL CURRENT IN A PARALLEL CONNECTION CIRCUIT. 1D AND 1F MODE REPLY11AC31 BDJJJ 10FREQUENCY AT WHICH MEASURED,CONNECTION,INDUCTANCE SERIES INDUCTANCE SERIES CONNECTION FREQUENCY AT WHICH MEASURED THE ACCEPTABLE LIMITS OF THE FREQUENCY FOR WHICH THE INDUCTANCE SERIES CONNECTION IS MEASURED. 2D AND 1B MODE REPLY21AC321AC20 BDJKJ 10FREQUENCY AT WHICH MEASURED,CONNECTION,INDUCTANCE PARALLEL INDUCTANCE PARALLEL CONNECTION FREQUENCY AT WHICH MEASURED THE ACCEPTABLE LIMITS OF THE FREQUENCY FOR WHICH THE INDUCTANCE PARALLEL CONNECTION IS MEASURED. 2D AND 1B MODE REPLY21AC321AC20 BDJLF T10ACCURACY IN PERCENT,CONNECTION,INDUCTANCE PARALLEL INDUCTANCE PARALLEL CONNECTION ACCURACY IN PERCENT THE ACCEPTABLE LIMITS OF DEVIATION FROM THE INDUCTANCE PARALLEL CONNECTION DESIGNED STANDARD OUTPUT VALUE,EXPRESSED IN PERCENT. 1F MODE REPLY 0 BDJMJ T10RANGE,INDUCTANCE,MUTUAL MUTUAL INDUCTANCE RANGE THE MINIMUM AND MAXIMUM RATING OF A REACTIVE CURRENT TO THE TOTAL CURRENT IN A MUTUAL INDUCTANCE CIRCUIT. 1D AND 1F MODE REPLY11AC31 BDJNF T10ACCURACY IN PERCENT,INDUCTANCE,MUTUAL MUTUAL INDUCTANCE ACCURACY IN PERCENT THE ACCEPTABLE LIMITS OF DEVIATION FROM THE MUTUAL INDUCTANCE DESIGNED STANDARD OUTPUT VALUE,EXPRESSED IN PERCENT. 1F MODE REPLY 0 BDJPJ 10RESISTANCE RATING,DC DC RESISTANCE RATING THE OPPOSITION TO THE FLOW OF DIRECT CURRENT OFFERED BY AN ITEM. 2D AND 1B MODE REPLY21AA571AC20 BDJQJ 10FREQUENCY RATING,SIGNAL,INPUT INPUT SIGNAL FREQUENCY RATING THE NUMBER OF COMPLETE CYCLE CHANGES,PER UNIT OF TIME,FOR WHICH THE INPUT SIGNAL IS RATED. 1D AND 1B MODE REPLY11AC32 BDJRJ /D/ 04DISTANCE FROM END OF RACK TO CENTER OF FIRST MOUNTING HOLE DISTANCE FROM END OF RACK TO CENTER OF FIRST MOUNTING HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BDJSJ /D/ 04LENGTH FROM END OF BODY TO FACE OF GEAR LENGTH FROM END OF BODY TO FACE OF GEAR NONE. 2D AND 1B MODE REPLY21AA051AC20 BDJTJ 04RADIUS,PITCH PITCH RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BDJWD /D/ 08LOCATION,HUB HUB LOCATION INDICATES THE LOCATION OF THE HUB ON THE ITEM. SELECT REPLY CODE 10AJ91 BDJXJ /D/ 04DIAMETER,HUB,FIRST END FIRST END HUB DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDJYJ /D/ 04DIAMETER,HUB,SECOND END SECOND END HUB DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDJZJ /D/ 04DISTANCE FROM END OF HUB TO CENTER OF TAPPED HOLE,FIRST END FIRST END DISTANCE FROM END OF HUB TO CENTER OF TAPPED HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKBJ /D/ 04DISTANCE FROM END OF HUB TO CENTER OF TAPPED HOLE,SECOND HOLE SECOND HOLE DISTANCE FROM END OF HUB TO CENTER OF TAPPED HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKCJ /D/ 04DIAMETER,END,FIRST END HUB FIRST END HUB END DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKDJ /D/ 04DIAMETER,END,SECOND END HUB SECOND END HUB END DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKFJ /D/ 04LENGTH,END,FIRST END HUB FIRST END HUB END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKGJ /D/ 04LENGTH,END,SECOND END HUB SECOND END HUB END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKHJ /D/ 04WIDTH,GROOVE,FIRST,FIRST END FIRST END FIRST GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKJJ /D/ 04WIDTH,GROOVE,FIRST,SECOND END SECOND END FIRST GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKKJ /D/ 04DIAMETER,GROOVE,FIRST,FIRST END FIRST END FIRST GROOVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKLJ /D/ 04DIAMETER,GROOVE,FIRST,SECOND END SECOND END FIRST GROOVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKMJ /D/ 04LENGTH FROM END OF HUB TO FIRST GROOVE,FIRST END FIRST END LENGTH FROM END OF HUB TO FIRST GROOVE NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKNJ /D/ 04LENGTH FROM END OF HUB TO FIRST GROOVE,SECOND END SECOND END LENGTH FROM END OF HUB TO FIRST GROOVE NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKPJ /D/ 04WIDTH,GROOVE,SECOND,FIRST END FIRST END SECOND GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKQJ /D/ 04WIDTH,GROOVE,SECOND,SECOND END SECOND END SECOND GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKRJ /D/ 04DIAMETER,GROOVE,SECOND,SECOND END SECOND END SECOND GROOVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKSJ /D/ 04LENGTH FROM END OF HUB TO SECOND GROOVE,FIRST END FIRST END LENGTH FROM END OF HUB TO SECOND GROOVE NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKTJ /D/ 04LENGTH FROM END OF HUB TO SECOND GROOVE,SECOND END SECOND END LENGTH FROM END OF HUB TO SECOND GROOVE NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKWJ /D/ 04DIAMETER,STEP,FIRST,FIRST END FIRST END FIRST STEP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKXJ /D/ 04DIAMETER,STEP,FIRST,SECOND END SECOND END FIRST STEP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKYJ /D/ 04LENGTH OF FIRST STEP,FIRST END FIRST END LENGTH OF FIRST STEP NONE. 2D AND 1B MODE REPLY21AA051AC20 BDKZJ /D/ 04LENGTH OF FIRST STEP,SECOND END SECOND END LENGTH OF FIRST STEP NONE. 2D AND 1B MODE REPLY21AA051AC20 BDLBJ /D/ 04DIAMETER,STEP,SECOND,FIRST END FIRST END SECOND STEP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDLCJ /D/ 04DIAMETER,STEP,SECOND,SECOND END SECOND END SECOND STEP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDLDJ /D/ 04LENGTH OF SECOND STEP,FIRST END FIRST END LENGTH OF SECOND STEP NONE. 2D AND 1B MODE REPLY21AA051AC20 BDLFJ /D/ 04LENGTH OF SECOND STEP,SECOND END SECOND END LENGTH OF SECOND STEP NONE. 2D AND 1B MODE REPLY21AA051AC20 BDLGJ /D/ 04DIAMETER,STEP,THIRD,FIRST END FIRST END THIRD STEP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDLHJ /D/ 04DIAMETER,STEP,THIRD,SECOND END SECOND END THIRD STEP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDLJJ /D/ 04LENGTH OF THIRD STEP,FIRST END FIRST END LENGTH OF THIRD STEP NONE. 2D AND 1B MODE REPLY21AA051AC20 BDLKJ /D/ 04LENGTH OF THIRD STEP,SECOND END SECOND END LENGTH OF THIRD STEP NONE. 2D AND 1B MODE REPLY21AA051AC20 BDLLJ /D/ 04LENGTH,SURFACE,FIRST END CLAMPING FIRST END CLAMPING SURFACE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BDLMD /D/ 07CHUCK,MACHINE,DRAFTING DRAFTING MACHINE CHUCK AN INDICATION OF WHETHER OR NOT A DRAFTING MACHINE CHUCK(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BDLNJ 04WIDTH,MAXIMUM MAXIMUM WIDTH THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ITEM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BDLPD /D/ 07SHEATH SHEATH AN INDICATION OF WHETHER OR NOT A SHEATH IS INCLUDED. SELECT REPLY CODE 10AA49 BDLQD /D/ 09MATERIAL,POLE POLE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE POLE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BDLRD /D/ 09MATERIAL,SHOE SHOE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHOE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BDLSD 19SYSTEM,MEASUREMENT MEASUREMENT SYSTEM AN INDICATION OF THE MEASURING SYSTEM USED WITH THE ITEM. SELECT REPLY CODE 10AM14 BDLTA 12QUANTITY,DIVISION,METER SCALE METER SCALE DIVISION QUANTITY THE NUMBER OF PART(S) INTO WHICH THE METER SCALE IS DIVIDED. 1A MODE REPLY 0 BDLWA 12QUANTITY,DIVISION,FOOT SCALE FOOT SCALE DIVISION QUANTITY THE NUMBER OF PART(S) INTO WHICH THE FOOT SCALE IS DIVIDED. 1A MODE REPLY 0 BDLXJ 04LENGTH,MINIMUM MINIMUM LENGTH A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BDLYJ 04LENGTH,BAND,COLOR COLOR BAND LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE COLOR BAND,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BDLZD 14SHAPE,TARGET TARGET SHAPE THE PHYSICAL CONFIGURATION OF A TARGET. SELECT REPLY CODE 10AD07 BDMBD /D/ 07VERNIER VERNIER AN INDICATION OF WHETHER OR NOT A VERNIER IS INCLUDED. SELECT REPLY CODE 10AA49 BDMCD 19GRADUATION,SCALE,VERNIER VERNIER SCALE GRADUATION AN INDICATION OF THE PARTS INTO WHICH A VERNIER SCALE IS GRADUATED. SELECT REPLY CODE 10AG67 BDMDD /D/ 07ADJUSTMENT,MICROMETER MICROMETER ADJUSTMENT AN INDICATION OF WHETHER OR NOT A MICROMETER ADJUSTMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BDMFD /D/ 07SCREW,CLAMP CLAMP SCREW AN INDICATION OF WHETHER OR NOT A CLAMP SCREW IS INCLUDED. SELECT REPLY CODE 10AA49 BDMGD /D/ 07DEVICE,LOCKING,AUTOMATIC AUTOMATIC LOCKING DEVICE AN INDICATION OF WHETHER OR NOT AN AUTOMATIC LOCKING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 BDMHD /D/ 07LEVEL,PLUMBING PLUMBING LEVEL AN INDICATION OF WHETHER OR NOT A PLUMBING LEVEL IS INCLUDED. SELECT REPLY CODE 10AA49 BDMJD /D/ 19END,ADAPTED,COUPLER COUPLER ADAPTED END AN INDICATION OF WHETHER ONE OR BOTH ENDS ARE ADPATED FOR A COUPLER. SELECT REPLY CODE 10AM96 BDMKJ 10CAPACITY RATING,LIQUID LIQUID CAPACITY RATING A MEASUREMENT OF THE RATED LIQUID CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BDMLD 18TYPE,DEVICE,CONTROL CONTROL DEVICE TYPE INDICATES THE TYPE OF CONTROL DEVICE PROVIDED. SELECT REPLY CODE 10AM97 BDMMJ 10CAPACITY,GRINDING,RAW MATERIAL RAW MATERIAL GRINDING CAPACITY THE RATED CAPACITY OF THE ITEM TO GRIND RAW MATERIAL. 2D AND 1B MODE REPLY22AG673AM98 BDMNA 12QUANTITY,MINIMUM,WIRE POINT WIRE POINT MINIMUM QUANTITY THE MINIMUM NUMBER OF WIRE POINT(S) USED IN THE ITEM. 1A MODE REPLY 0 BDMPD 19CONSTRUCTION,HUB,WOOD WOOD HUB CONSTRUCTION THE STRUCTURAL CHARACTERISTIC OF THE WOOD HUB. SELECT REPLY CODE 10AL59 BDMQD /D/ 09MATERIAL,FILL FILL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FILL MATERIAL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BDMRD 18TYPE,FILL,WIRE WIRE FILL TYPE INDICATES THE TYPE OF WIRE FILL INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AM99 BDMSA 12QUANTITY,ROW,FILL FILL ROW QUANTITY THE NUMBER OF FILL ROW(S) INCLUDED IN THE ITEM. 1A MODE REPLY 0 BDMTD 19CONSTRUCTION,PLY PLY CONSTRUCTION A TERM INDICATING HOW THE PLIES OF MATERIAL ARE CONSTRUCTED. SELECT REPLY CODE 10AL98 BDMWD 18TYPE,FOLD,DISK DISK FOLD TYPE INDICATES THE TYPE OF FOLDING USED IN THE CONSTRUCTION OF THE DISK. SELECT REPLY CODE 10AL76 BDMXD 11METHOD,STITCHING STITCHING METHOD THE MEANS USED FOR STITCHING THE ITEM. SELECT REPLY CODE 10AN00 BDMYA 12QUANTITY,ROW,STITCHING STITCHING ROW QUANTITY THE NUMBER OF ROWS OF STITCHING USED IN THE ITEM. 1A MODE REPLY 0 BDMZJ 10SPACING,ROW,STITCHING STITCHING ROW SPACING THE NUMERIC VALUE WHICH ESTABLISHES THE DISTANCE BETWEEN THE ROWS OF STITCHING. 2D AND 1B MODE REPLY21AA051AC20 BDNBJ 04DIAMETER,MANDREL MANDREL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MANDREL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BDNCJ /D/ 04DIAMETER AT SMALL END OF TAPER,HOLE,ARBOR ARBOR HOLE DIAMETER AT SMALL END OF TAPER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDNDJ 04WIDTH AT HUB,BRUSH BRUSH WIDTH AT HUB NONE. 2D AND 1B MODE REPLY21AA051AC20 BDNFJ 04LENGTH,TRIM TRIM LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BDNGJ 04LENGTH EXCLUDING STEM LENGTH EXCLUDING STEM NONE. 2D AND 1B MODE REPLY21AA051AC20 BDNHJ 10CAPACITY,PEELING,MATERIAL MATERIAL PEELING CAPACITY THE RATED MATERIAL PEELING CAPACITY OF THE ITEM. 2D AND 1B MODE REPLY22AG673AN02 BDNJJ 10CAPACITY,MIXING,FLOUR FLOUR MIXING CAPACITY THE RATED FLOUR MIXING CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BDNKJ /D/ 10CAPACITY,BREAD,MAXIMUM RATED FIELD RATION MAXIMUM RATED FIELD RATION BREAD CAPACITY THE MAXIMUM RATED CAPACITY OF FIELD RATION BREAD THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY12AG67 BDNLJ 10COEFFICIENT RATING,REDUCTION,NOISE NOISE REDUCTION COEFFICIENT RATING THE MEASURED RATING OF THE NOISE REDUCTION. 1D AND 1B MODE REPLY11AC20 BDNMD 18TYPE,SURFACE,EXPOSED FACE EXPOSED FACE SURFACE TYPE INDICATES THE TYPE OF EXPOSED FACE SURFACE PROVIDED. SELECT REPLY CODE 10AA43 BDNND /D/ 07BINDER,JACKET JACKET BINDER AN INDICATION OF WHETHER OR NOT A JACKET BINDER IS INCLUDED. SELECT REPLY CODE 10AA49 BDNPD /D/ 07CORE,TREATED,ASPHALT ASPHALT TREATED CORE AN INDICATION OF WHETHER OR NOT AN ASPHALT TREATED CORE IS INCLUDED. SELECT REPLY CODE 10AA49 BDNQD /D/ 07COVER,PAPER,WATER REPELLENT WATER REPELLENT PAPER COVER AN INDICATION OF WHETHER OR NOT A WATER REPELLENT PAPER COVER IS INCLUDED. SELECT REPLY CODE 10AA49 BDNRL 16STYLE,JOINT,LONG EDGE LONG EDGE JOINT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LONG EDGE JOINT. 1L MODE REPLY 0 BDNSL 16STYLE,JOINT,SHORT EDGE SHORT EDGE JOINT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SHORT EDGE JOINT. 1L MODE REPLY 0 BDNTD /D/ 07FEATURE,FLAMEPROOF FLAMEPROOF FEATURE AN INDICATION OF WHETHER OR NOT A FLAMEPROOF FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BDNWD /D/ 07SURFACE,COATED,WATER REPELLENT WATER REPELLENT COATED SURFACE AN INDICATION OF WHETHER OR NOT THE SURFACE IS PROVIDED WITH A WATER REPELLENT COATING. SELECT REPLY CODE 10AB22 BDNXD /D/ 07PROVISION,DECORATION,ONE SIDE ONE SIDE DECORATION PROVISION AN INDICATION OF WHETHER OR NOT A PROVISION FOR ONE SIDE DECORATION IS PROVIDED. SELECT REPLY CODE 10AB22 BDNYD 01COLOR,SIDE,DECORATIVE DECORATIVE SIDE COLOR THE HUE OR TINT OF THE DECORATIVE SIDE. SELECT REPLY CODE 10AD06 BDNZJ 10DENSITY RATING DENSITY RATING AN INDICATION OF THE RATED DENSITY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BDPBD /D/ 09MATERIAL,LAYER LAYER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LAYER(S) IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BDPCD 19PROTECTION,ENVIRONMENTAL,LAYER LAYER ENVIRONMENTAL PROTECTION THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT THE LAYER IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY. SELECT REPLY CODE 10AA65 BDPDJ 04THICKNESS,LAYER LAYER THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE LAYER,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BDPFD /D/ 07BINDER,ADDED ADDED BINDER AN INDICATION OF WHETHER OR NOT AN ADDED BINDER IS INCLUDED. SELECT REPLY CODE 10AA49 BDPGD 08LOCATION,SURFACE,REFLECTIVE REFLECTIVE SURFACE LOCATION INDICATES THE LOCATION OF THE REFLECTIVE SURFACE ON THE ITEM. SELECT REPLY CODE 10AJ91 BDPHD /D/ 07FEATURE,QUILTED QUILTED FEATURE AN INDICATION OF WHETHER OR NOT A QUILTED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BDPJD /D/ 08LOCATION,FACILITY,MOUNTING MOUNTING FACILITY LOCATION INDICATES THE LOCATION OF THE MOUNTING FACILITY IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 BDPKJ 10PERCENTAGE,CONTENT,ASBESTOS ASBESTOS CONTENT PERCENTAGE THE ASBESTOS CONTENT OF THE ITEM,EXPRESSED IN PERCENT. 1D AND 1B MODE REPLY11AC20 BDPLD 03DESIGNATION,GRADE GRADE DESIGNATION A DESIGNATION OF THE GRADE BY WHICH THE ITEM IS IDENTIFIED. SELECT REPLY CODE 10AL91 BDPMD /D/ 07FEATURE,REINFORCEMENT,WIRE WIRE REINFORCEMENT FEATURE AN INDICATION OF WHETHER OR NOT A WIRE REINFORCEMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BDPNJ A12QUANTITY,MINIMUM,WARP THREAD WARP THREAD MINIMUM QUANTITY THE MINIMUM NUMBER OF WARP THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY11AB39 BDPPJ A12QUANTITY,MINIMUM,FILLING THREAD FILLING THREAD MINIMUM QUANTITY THE MINIMUM NUMBER OF FILLING THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY11AB39 BDPQJ 10WEIGHT,NOMINAL NOMINAL WEIGHT A RELATIVE NOMINAL MEASURE OF THE MASS OF AN ITEM WITH RESPECT TO ITS DENSITY. 1D AND 1B MODE REPLY12AG67 BDPRD 01COLOR,STRIPE,IDENTIFICATION IDENTIFICATION STRIPE COLOR THE HUE OR TINT OF THE IDENTIFICATION STRIPE. SELECT REPLY CODE 10AD06 BDPSD /D/ 07FEATURE,REINFORCEMENT,JACKET WIRE JACKET WIRE REINFORCEMENT FEATURE AN INDICATION OF WHETHER OR NOT A JACKET WIRE REINFORCEMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BDPTD /D/ 07TREATMENT,RESIN RESIN TREATMENT AN INDICATION OF WHETHER OR NOT A RESIN TREATMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BDPWD /D/ 07FEATURE,CONSTRUCTION,INTERWOVEN INTERWOVEN CONSTRUCTION FEATURE AN INDICATION OF WHETHER OR NOT AN INTERWOVEN CONSTRUCTION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BDPXD /D/ 07FEATURE,CONSTRUCTION,THREAD BOUND THREAD BOUND CONSTRUCTION FEATURE AN INDICATION OF WHETHER OR NOT A THREAD BOUND CONSTRUCTION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BDPYJ /D/ 10WEIGHT,SHEET SHEET WEIGHT A RELATIVE MEASURE OF THE MASS OF THE SHEET WITH RESPECT TO ITS DENSITY. 2D AND 1B MODE REPLY22AG671AC20 BDPZD 07CHARACTERISTIC,TEMPER TEMPER CHARACTERISTIC AN INDICATION OF THE TEMPER CHARACTERISTIC OF AN ITEM. SELECT REPLY CODE 10AA09 BDQBH /D/ 18TYPE AND LOCATION,SURFACE SURFACE TYPE AND LOCATION INDICATES THE SURFACE TYPE AND ITS LOCATION ON THE ITEM. PLEASE USE MRC CBCL IN PLACE OF THIS CANCELED MRC. 2D MODE REPLY 23AM353AJ91 BDQCD /D/ 09MATERIAL,PLY PLY MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PLY IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH USE OF ISAC FOR THIS CANCELED MRC. SELECT REPLY CODE 10AD09 BDQDD /D/ 09MATERIAL BETWEEN PLIES,ADHESIVE ADHESIVE MATERIAL BETWEEN PLIES THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ADHESIVE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT,USED FOR BONDING PLIES. SELECT REPLY CODE 10AD09 BDQFD /D/ 18TYPE,COATING,OUTER OUTER COATING TYPE INDICATES THE TYPE OF OUTER COATING PROVIDED. SELECT REPLY CODE 10AL61 BDQGD /D/ 08LOCATION,COATING,OUTER OUTER COATING LOCATION INDICATES THE LOCATION OF THE ITEM TO WHICH THE OUTER COATING IS APPLIED. SELECT REPLY CODE 10AJ91 BDQJJ 10CAPACITY,ROLL ROLL CAPACITY THE AMOUNT OF MATERIAL THE ROLL WILL ACCOMMODATE. 2D AND 1B MODE REPLY22AG671AC20 BDQKJ 10WEIGHT PER SQUARE WEIGHT PER SQUARE A RELATIVE MEASURE OF THE MASS OF AN ITEM WITH RESPECT TO ITS DENSITY PER SQUARE. 1D AND 1B MODE REPLY12AG67 BDQLD /D/ 13THREAD SERIES DESIGNATOR,HOLE,SCREW,CLAMPING CLAMPING SCREW HOLE THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF A THREADED CLAMPING SCREW HOLE. SELECT REPLY CODE 10AH06 BDQMJ 13THREAD LENGTH,HOLE,CLAMPING SCREW CLAMPING SCREW HOLE THREAD LENGTH A MEASURE OF THE EXTENT OF CLAMPING SCREW HOLE THREADS MEASURED ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS. 2D AND 1B MODE REPLY21AA051AC20 BDQND /D/ 07PROTRUSION,RELEASE,INTEGRAL THUMB INTEGRAL THUMB RELEASE PROTRUSION AN INDICATION OF WHETHER OR NOT AN INTEGRAL THUMB RELEASE PROTRUSION IS INCLUDED. SELECT REPLY CODE 10AA49 BDQPA 12QUANTITY,ACCOMMODATION,WIRE WIRE ACCOMMODATION QUANTITY THE NUMBER OF WIRE ACCOMMODATIONS PROVIDED. 1A MODE REPLY 0 BDQQG 04SIZE,ACCOMMODATION,WIRE WIRE ACCOMMODATION SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE WIRE ACCOMMODATION/S/. FULL TEXT WRITE-IN 0 BDQRA 12QUANTITY,FINGER,CONTACT CONTACT FINGER QUANTITY THE NUMBER OF CONTACT FINGERS PROVIDED. 1A MODE REPLY 0 BDQSA /D/ 12QUANTITY ACCOMMODATED,RELAY RELAY QUANTITY ACCOMMODATED THE NUMBER OF RELAY(S) ACCOMMODATED BY THE ITEM. 1A MODE REPLY 0 BDQTG /D/ 19CONFIGURATION/D/,MOUNTING,RELAY RELAY MOUNTING CONFIGURATION/D/ THE NARRATIVE EXPRESSION USED FOR INDICATING THE CONFIGURATION OF THE RELAY MOUNTING. FULL TEXT WRITE-IN 0 BDQWG 19CONFIGURATION,MOUNTING,PLATE PLATE MOUNTING CONFIGURATION THE NARRATIVE EXPRESSION USED FOR INDICATING THE CONFIGURATION OF THE PLATE MOUNTING. FULL TEXT WRITE-IN 0 BDQXG /D/ 19DIMENSIONS,OUTSIDE,OVERALL OVERALL OUTSIDE DIMENSIONS THE MEASUREMENTS TAKEN TO SPECIFY THE OVERALL OUTSIDE DIMENSIONS. FULL TEXT WRITE-IN 0 BDQYG /D/ 19DIMENSIONS,GROOVE GROOVE DIMENSIONS THE MEASUREMENTS TAKEN TO SPECIFY THE GROOVE DIMENSIONS. FULL TEXT WRITE-IN 0 BDQZD /D/ 17SURFACE TREATMENT,BASE BASE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE BASE. SELECT REPLY CODE 10AD09 BDRBG 19POSITION,GROOVE GROOVE POSITION INDICATES THE POSITION OF THE GROOVE(S) ON THE ITEM. FULL TEXT WRITE-IN 0 BDRCD /D/ 17SURFACE TREATMENT,STEM STEM SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE STEM SURFACE. SELECT REPLY CODE 10AD09 BDRDD /D/ 07SWIVEL SWIVEL AN INDICATION OF WHETHER OR NOT A SWIVEL IS INCLUDED. SELECT REPLY CODE 10AA49 BDRFA 12QUANTITY,LEG LEG QUANTITY THE NUMBER OF LEGS PROVIDED. 1A MODE REPLY 0 BDRGA /D/ 16STYLE,PROFILE,TOOTH TOOTH PROFILE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE PROFILE OF THE TOOTH. 1A MODE REPLY 0 BDRHJ 04DIAMETER,INSIDE,SEAT END SEAT END INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SEAT END,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BDRJD /D/ 07FEATURE,KNURLING,FINGER-GRIP FINGER-GRIP KNURLING FEATURE AN INDICATION OF WHETHER OR NOT A FINGER-GRIP KNURLING FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BDRKD /D/ 07HOLE,SETSCREW,TAPPED TAPPED SETSCREW HOLE AN INDICATION OF WHETHER OR NOT A TAPPED SETSCREW HOLE IS INCLUDED. SELECT REPLY CODE 10AA49 BDRLD /D/ 07SETSCREW SETSCREW AN INDICATION OF WHETHER OR NOT A SETSCREW(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BDRMD /D/ 07HOLE,DRILLED,SAFETY WIRE SAFETY WIRE DRILLED HOLE AN INDICATION OF WHETHER OR NOT A SAFETY WIRE DRILLED HOLE IS PROVIDED. SELECT REPLY CODE 10AB22 BDRND /D/ 07SLOT,WRENCHING WRENCHING SLOT AN INDICATION OF WHETHER OR NOT A WRENCHING SLOT IS PROVIDED. SELECT REPLY CODE 10AB22 BDRPD 18TYPE,TRANSMISSION,MOTION MOTION TRANSMISSION TYPE INDICATES THE TYPE OF MOTION TRANSMISSION. SELECT REPLY CODE 10AC60 BDRQD 19PATTERN,TRANSMISSION,MOTION MOTION TRANSMISSION PATTERN AN INDICATION OF THE PATTERN OF MOTION TRANSMISSION. SELECT REPLY CODE 10AD55 BDRRD 18TYPE,DRIVE,MOTION TRANSMISSION MOTION TRANSMISSION DRIVE TYPE INDICATES THE TYPE OF MOTION TRANSMISSION DRIVE PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AD49 BDRSD /D/ 07SHEET,AFFIXED AFFIXED SHEET AN INDICATION OF WHETHER OR NOT AN AFFIXED SHEET IS INCLUDED. SELECT REPLY CODE 10AA49 BDRTD /D/ 07FACE,GROOVED GROOVED FACE AN INDICATION OF WHETHER OR NOT A GROOVED FACE IS PROVIDED. SELECT REPLY CODE 10AB22 BDRWD /D/ 07SPRING,ANTISTATIC ANTISTATIC SPRING AN INDICATION OF WHETHER OR NOT AN ANTISTATIC SPRING IS INCLUDED. SELECT REPLY CODE 10AA49 BDRXD /D/ 07ATTACHMENT,END END ATTACHMENT AN INDICATION OF WHETHER OR NOT AN END ATTACHMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BDRYA /D/ 16STYLE,ATTACHMENT,END END ATTACHMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END ATTACHMENT. 1A MODE REPLY 0 BDRZD /D/ 09MATERIAL,ATTACHMENT,END END ATTACHMENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH AN END ATTACHMENT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BDSBD /D/ 17SURFACE TREATMENT,ATTACHMENT,END END ATTACHMENT SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE END ATTACHMENT. SELECT REPLY CODE 10AD09 BDSCB /D/ 10ANGULAR POSITION IN DEG,RELATIVE,CONNECTING CENTERS CONNECTING CENTERS RELATIVE ANGULAR POSITION IN DEG A MEASUREMENT OF THE RELATIVE ANGULAR POSITION OF THE CONNECTING CENTERS,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BDSDJ T10ACCURACY,MAINTAINED MAINTAINED ACCURACY AN INDICATION OF THE EXTENT AN ITEM MAINTAINS ITS RATED VALUE/S/. 1D AND 1F MODE REPLY12AG67 BDSFD /D/ 08LOCATION,BEARING,CONNECTING HOLE CONNECTING HOLE BEARING LOCATION INDICATES THE LOCATION OF THE CONNECTING HOLE BEARING. SELECT REPLY CODE 10AJ91 BDSGD /D/ 08LOCATION,BUSHING,CONNECTING HOLE CONNECTING HOLE BUSHING LOCATION INDICATES THE LOCATION OF THE CONNECTING HOLE BUSHING. SELECT REPLY CODE 10AJ91 BDSHD /D/ 07LOCKNUT LOCKNUT AN INDICATION OF WHETHER OR NOT A LOCKNUT IS INCLUDED. SELECT REPLY CODE 10AA49 BDSJD /D/ 07FACE,RAISED RAISED FACE AN INDICATION OF WHETHER OR NOT A RAISED FACE IS PROVIDED. SELECT REPLY CODE 10AB22 BDSKJ /D/ 10CURRENT RATING,MAXIMUM,COIL COIL MAXIMUM CURRENT RATING THE MAXIMUM CONTINUOUS CURRENT WHICH MUST NOT BE EXCEEDED IN ORDER TO AVOID DAMAGE TO THE COIL. 1D AND 1B MODE REPLY11AC30 BDSLJ /D/ 04HEIGHT FROM FLAT TO RADIAL CENTER HEIGHT FROM FLAT TO RADIAL CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDSMJ /D/ 04HEIGHT,SPLINE SPLINE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BDSNJ /D/ 04THICKNESS,TOOTH,FIRST END SPLINE FIRST END SPLINE TOOTH THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BDSPJ /D/ 04THICKNESS,TOOTH,SECOND END SPLINE SECOND END SPLINE TOOTH THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BDSQA 12QUANTITY,SPLINE,FIRST END FIRST END SPLINE QUANTITY NONE. 1A MODE REPLY 0 BDSRA 12QUANTITY,SPLINE,SECOND END SECOND END SPLINE QUANTITY NONE. 1A MODE REPLY 0 BDSSJ /D/ 04LENGTH OF SPLINE,EFFECTIVE,FIRST END FIRST END EFFECTIVE LENGTH OF SPLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 BDSTJ /D/ 04LENGTH OF SPLINE,EFFECTIVE,SECOND END SECOND END EFFECTIVE LENGTH OF SPLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 BDSWJ /D/ 04DIAMETER,PITCH,FIRST END SPLINE FIRST END SPLINE PITCH DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDSXJ /D/ 04DIAMETER,PITCH,SECOND END SPLINE SECOND END SPLINE PITCH DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDSYB /D/ 04ANGLE,PRESSURE,SPLINE TOOTH,FIRST END FIRST END SPLINE TOOTH PRESSURE ANGLE NONE. 1B MODE REPLY 0 BDSZB /D/ 04ANGLE,PRESSURE,SPLINE TOOTH,SECOND END SECOND END SPLINE TOOTH PRESSURE ANGLE NONE. 1B MODE REPLY 0 BDTBJ /D/ 04DIAMETER,SLOT,FIRST END KEY FIRST END KEY SLOT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDTCJ /D/ 04DIAMETER,SLOT,SECOND END KEY SECOND END KEY SLOT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDTDJ /D/ 04LENGTH FROM END OF HUB TO RADIAL CENTER OF KEY SLOT,FIRST END FIRST END LENGTH FROM END OF HUB TO RADIAL CENTER OF KEY SLOT NONE. 2D AND 1B MODE REPLY21AA051AC20 BDTFJ /D/ 04LENGTH FROM END OF HUB TO RADIAL CENTER OF KEY SLOT,SECOND END SECOND END LENGTH FROM END OF HUB TO RADIAL CENTER OF KEY SLOT NONE. 2D AND 1B MODE REPLY21AA051AC20 BDTJJ /D/ 04LENGTH,KEYWAY,EXTERNAL,FIRST END FIRST END EXTERNAL KEYWAY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BDTKJ /D/ 04LENGTH,KEYWAY,EXTERNAL,SECOND END SECOND END EXTERNAL KEYWAY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BDTLJ /D/ 04WIDTH,KEYWAY,EXTERNAL,FIRST END FIRST END EXTERNAL KEYWAY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BDTMJ /D/ 04WIDTH,KEYWAY,EXTERNAL,SECOND END SECOND END EXTERNAL KEYWAY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BDTNJ /D/ 04DEPTH,KEYWAY,FIRST END FIRST END KEYWAY DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BDTPD /D/ 08LOCATION,SPOKE SPOKE LOCATION INDICATES THE LOCATION OF THE SPOKES IN RELATION TO THE CENTERLINE OF THE GEAR TEETH. SELECT REPLY CODE 10AJ91 BDTQJ /D/ 04DIAMETER,GROOVE,SECOND,FIRST END FIRST END SECOND GROOVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDTRD /D/ 08LOCATION,WEB WEB LOCATION INDICATES THE LOCATION OF THE WEB IN RELATION TO THE CENTERLINE OF THE GEAR TEETH. SELECT REPLY CODE 10AJ91 BDTSJ /D/ 04DEPTH,KEYWAY,SECOND END SECOND END KEYWAY DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BDTTD /D/ 07PROVISION,BORE BORE PROVISION AN INDICATION OF WHETHER OR NOT AN AXIAL HOLE IS INCLUDED IN THE ITEM FOR THE PURPOSE OF INSERTING OR ADMITTING A SHAFT OR SIMILAR DEVICE. SELECT REPLY CODE 10AA49 BDTWJ /D/ 04LENGTH,SURFACE,CLAMPING,SECOND END SECOND END CLAMPING SURFACE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BDTXJ 04DIAMETER,PITCH,SPLINE SPLINE PITCH DIAMETER A MEASUREMENT OF THE SPLINE PITCH DIAMETER. 2D AND 1B MODE REPLY21AA051AC20 BDTYB /D/ 04ANGLE IN DEG,PRESSURE,TOOTH TOOTH PRESSURE ANGLE IN DEG NONE. 1B MODE REPLY 0 BDTZJ 04DIAMETER,MAJOR,SERRATION SERRATION MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTERMOST SURFACE OF A SERRATED BODY,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BDWBJ /D/ 19DIMENSION FROM BORE CENTER TO TAPERED KEYWAY BOTTOM,MAJOR MAJOR DIMENSION FROM BORE CENTER TO TAPERED KEYWAY BOTTOM NONE. 2D AND 1B MODE REPLY21AA051AC20 BDWCJ /D/ 19DIMENSIONS FROM BORE CENTER TO TAPERED KEYWAY BOTTOM,MINOR MINOR DIMENSION FROM BORE CENTER TO TAPERED KEYWAY BOTTOM NONE. 2D AND 1B MODE REPLY21AA051AC20 BDWDJ /D/ 19DIMENSION FROM BORE CENTER TO INTEGRAL TAPERED KEY TOP,MAJOR MAJOR DIMENSION FROM BORE CENTER TO INTEGRAL TAPERED KEY TOP NONE. 2D AND 1B MODE REPLY21AA051AC20 BDWFJ /D/ 19DIMENSION FROM BORE CENTER TO INTEGRAL TAPERED KEY TOP,MINOR MINOR DIMENSION FROM BORE CENTER TO INTEGRAL TAPERED KEY TOP NONE. 2D AND 1B MODE REPLY21AA051AC20 BDWGJ /D/ 04DIAMETER OF TAPERED SERRATIONS,MAJOR,LARGEST LARGEST MAJOR DIAMETER OF TAPERED SERRATIONS NONE. 2D AND 1B MODE REPLY21AA051AC20 BDWHJ /D/ 04DIAMETER OF TAPERED SERRATIONS,MINOR,LARGEST LARGEST MINOR DIAMETER OF TAPERED SERRATIONS NONE. 2D AND 1B MODE REPLY21AA051AC20 BDWJJ /D/ 04DIAMETER OF TAPERED SERRATIONS,MINOR,SMALLEST SMALLEST MINOR DIAMETER OF TAPERED SERRATIONS NONE. 2D AND 1B MODE REPLY21AA051AC20 BDWKJ 04DIAMETER,KNIFE,SLICING SLICING KNIFE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SLICING KNIFE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BDWLJ 04THICKNESS,SLICE SLICE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A SLICE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BDWMD /D/ 07FEATURE,SHINGLING SHINGLING FEATURE AN INDICATION OF WHETHER OR NOT A SHINGLING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BDWND /D/ 07FEATURE,GROUPING GROUPING FEATURE AN INDICATION OF WHETHER OR NOT A GROUPING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BDWPD /D/ 07FEATURE,DISCHARGE,CONVEYOR CONVEYOR DISCHARGE FEATURE AN INDICATION OF WHETHER OR NOT A CONVEYOR DISCHARGE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BDWQD /D/ 07FEATURE,CIRCULATING,WATER WATER CIRCULATING FEATURE AN INDICATION OF WHETHER OR NOT A WATER CIRCULATING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BDWRG 02DESIGN,FRAME FRAME DESIGN THE DESIGN OF THE FRAME. FULL TEXT WRITE-IN 0 BDWSD /D/ 07HANDLE,METAL METAL HANDLE AN INDICATION OF WHETHER OR NOT A METAL HANDLE IS INCLUDED. SELECT REPLY CODE 10AA49 BDWTD 11METHOD,HEATING HEATING METHOD THE MEANS BY WHICH THE ITEM IS HEATED. SELECT REPLY CODE 10AM63 BDWWJ 10WATTAGE RATING WATTAGE RATING THE RATED POWER THAT AN ITEM CAN SAFELY CONSUME OR PROVIDE. 1D AND 1B MODE REPLY12AB49 BDWXJ A14SHAPE AND QUANTITY,OPENING OPENING SHAPE AND QUANTITY THE PHYSICAL CONFIGURATION AND NUMBER OF OPENING(S) IN THE ITEM. 1D AND 1A MODE REPLY12AD07 BDWZJ 10CAPACITY,INSERT INSERT CAPACITY THE AMOUNT OF LIQUID,GRANULES,AND THE LIKE,THE INSERT/S/ WILL HOLD. 1D AND 1B MODE REPLY12AG67 BDXBD /D/ 07SHELF,PROTECTOR PROTECTOR SHELF AN INDICATION OF WHETHER OR NOT A PROTECTOR SHELF IS INCLUDED. SELECT REPLY CODE 10AA49 BDXCD /D/ 09MATERIAL,TOP TOP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TOP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH ISAC TABLE 0230 IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 BDXDD /D/ 07SHELF SHELF AN INDICATION OF WHETHER OR NOT A SHELF(VES) IS INCLUDED. SELECT REPLY CODE 10AA49 BDXFD /D/ 08LOCATION,SHELF SHELF LOCATION INDICATES THE LOCATION OF THE SHELF(VES) FOR THE ITEM. SELECT REPLY CODE 10AD07 BDXGD /D/ 07RACK,UTENSIL,OVERHEAD OVERHEAD UTENSIL RACK AN INDICATION OF WHETHER OR NOT AN OVERHEAD UTENSIL RACK IS INCLUDED. SELECT REPLY CODE 10AA49 BDXHA /D/ 10CAPACITY,RACK,UTENSIL UTENSIL RACK CAPACITY THE NUMBER OF UTENSILS THE RACK WILL ACCOMMODATE. 1A MODE REPLY 0 BDXJD 18TYPE,ELEMENT,HEATING HEATING ELEMENT TYPE INDICATES THE TYPE OF HEATING ELEMENT PROVIDED. SELECT REPLY CODE 10AN01 BDXKJ 04LENGTH FROM CIRCLE OUTER EDGE,ARM ARM LENGTH FROM CIRCLE OUTER EDGE A MEASUREMENT OF THE LONGEST DIMENSION OF THE ARM LENGTH FROM THE OUTER EDGE OF A CIRCLE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BDXLD /D/ 07ADJUSTMENT,HAIRSPRING HAIRSPRING ADJUSTMENT AN INDICATION OF WHETHER OR NOT A HAIRSPRING ADJUSTMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BDXMD /D/ 07POINT,STEEL,ADJUSTABLE ADJUSTABLE STEEL POINT AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE STEEL POINT/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BDXND /D/ 07HOLDER,BOWL,VACUUM COFFEE MAKER VACUUM COFFEE MAKER BOWL HOLDER AN INDICATION OF WHETHER OR NOT A VACUUM COFFEE MAKER BOWL HOLDER IS PROVIDED. SELECT REPLY CODE 10AB22 BDXPA 12QUANTITY,SWITCH,CONTROL CONTROL SWITCH QUANTITY THE NUMBER OF CONTROL SWITCHES PROVIDED. 1A MODE REPLY 0 BDXQJ 10CAPACITY,BOWL,ACCOMMODATED ACCOMMODATED BOWL CAPACITY THE CAPACITY OF THE BOWL THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY12AG67 BDXRA 12QUANTITY,BOWL BOWL QUANTITY THE NUMBER OF BOWLS FURNISHED WITH THE ITEM. 1A MODE REPLY 0 BDXSB 12QUANTITY PER MINUTE,SLICE,RATED RATED SLICE QUANTITY PER MINUTE THE RATED NUMBER OF SLICE(S) PER MINUTE. 1B MODE REPLY 0 BDXTJ T10RANGE,CAPACITY,BOWL BOWL CAPACITY RANGE THE MINIMUM TO MAXIMUM CAPACITY OF THE BOWL. 1D AND 1F MODE REPLY12AG67 BDXWD /D/ 09MATERIAL,BOWL BOWL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BOWL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BDXXA 12QUANTITY,DOLLY DOLLY QUANTITY THE NUMBER OF DOLLY(IES) FURNISHED WITH THE ITEM. 1A MODE REPLY 0 BDXYJ 10CAPACITY ACCOMMODATED,BOWL BOWL CAPACITY ACCOMMODATED THE CAPACITY OF THE BOWL THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY12AG67 BDXZJ T10RANGE ACCOMMODATED,CAPACITY,BOWL BOWL CAPACITY RANGE ACCOMMODATED THE CAPACITY RANGE OF THE BOWL THE ITEM WILL ACCOMMODATE. 1D AND 1F MODE REPLY12AG67 BDYCD 11METHOD,SUPPORTING,PAN PAN SUPPORTING METHOD THE MEANS PROVIDED TO SUPPORT THE PAN(S). SELECT REPLY CODE 10AH72 BDYDA 12QUANTITY ACCOMMODATED,PAN PAN QUANTITY ACCOMMODATED THE NUMBER OF PAN(S) THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 BDYFJ T04SIZE,PAN PAN SIZE DESIGNATES THE NUMERIC SIZE OF THE PAN. 1D AND 1F MODE REPLY12AG67 BDYGD 18TYPE,DEVICE,HUMIDIFIER HUMIDIFIER DEVICE TYPE INDICATES THE TYPE OF DEVICE USED TO PROVIDE CONTROLLED HUMIDITY WITHIN THE ITEM. SELECT REPLY CODE 10AH83 BDYHD /D/ 07COMPARTMENT,SILVERWARE,REMOVABLE REMOVABLE SILVERWARE COMPARTMENT AN INDICATION OF WHETHER OR NOT A REMOVABLE SILVERWARE COMPARTMENT IS PROVIDED. SELECT REPLY CODE 10AB22 BDYJJ 04DIAMETER,MINOR,SERRATION SERRATION MINOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INNERMOST SURFACE OF A SERRATED BODY,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BDYKJ 04DIAMETER,PITCH,SERRATION SERRATION PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF THE SERRATION. 2D AND 1B MODE REPLY21AA051AC20 BDYLJ /D/ 04DIAMETER,PITCH,MAJOR,TAPERED SERRATION TAPERED SERRATION MAJOR PITCH DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BDYMD /D/ 08LOCATION,BORE,PARTIAL PARTIAL BORE LOCATION INDICATES THE END OF THE ITEM THAT HAS BEEN FINISHED,IF THE BORE EXTENDS ONLY PARTIALLY THROUGH THE HUB. SELECT REPLY CODE 10AJ91 BDYND /D/ 08LOCATION,DIAMETER,LARGEST,SERRATED TAPER BORE SERRATED TAPER BORE LARGEST DIAMETER LOCATION INDICATES THE END OF THE ITEM WITH THE LARGEST DIAMETER OF THE SERRATED TAPER BORE. SELECT REPLY CODE 10AJ91 BDYPD /D/ 08LOCATION,DIAMETER,MINOR,TAPERED BORE TAPERED BORE MINOR DIAMETER LOCATION INDICATES THE LOCATION OF THE SMALLEST DIAMETER OF THE TAPERED BORE ON THE ITEM. SELECT REPLY CODE 10AJ91 BDYQD /D/ 08LOCATION,DEPTH,MAXIMUM,TAPERED KEYWAY TAPERED KEYWAY MAXIMUM DEPTH LOCATION INDICATES THE LOCATION OF THE MAXIMUM DEPTH OF THE TAPERED KEYWAY ON THE ITEM. SELECT REPLY CODE 10AJ91 BDYRD /D/ 08LOCATION,HEIGHT,MINIMUM,INTEGRAL TAPERED KEY INTEGRAL TAPERED KEY MINIMUM HEIGHT LOCATION INDICATES THE END OF THE ITEM WITH THE SMALLEST DIMENSION FROM THE CENTER OF THE BORE TO THE TOP OF THE INTEGRAL TAPERED KEY. SELECT REPLY CODE 10AJ91 BDYSD 08LOCATION,COUNTERBORE COUNTERBORE LOCATION INDICATES THE LOCATION OF THE COUNTERBORE ON THE ITEM. SELECT REPLY CODE 10AJ91 BDYTD /D/ 18TYPE,TEETH,GEAR GEAR TEETH TYPE INDICATES THE TYPE OF GEAR TEETH PROVIDED. SELECT REPLY CODE 10AL23 BDYWD /D/ 18TYPE,TOOTH,DOUBLE HELIX DOUBLE HELIX TOOTH TYPE INDICATES THE TYPE OF DOUBLE HELIX TOOTH PROVIDED. SELECT REPLY CODE 10AL23 BDYXA 12QUANTITY,TEETH,GEAR GEAR TEETH QUANTITY THE NUMBER OF GEAR TEETH PROVIDED. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 1A MODE REPLY 0 BDYYG /D/ 10PITCH PITCH A MEASUREMENT OF THE DISTANCE ALONG A PITCH LINE. FULL TEXT WRITE-IN 0 BDYZD /D/ 19FORM,TOOTH TOOTH FORM AN INDICATION AS TO WHETHER THE TEETH OF A GEAR OR RACK ARE A STANDARD DEPTH OR MODIFIED TO A SHORTER DEPTH. SELECT REPLY CODE 10AD07 BDZBJ /D/A04ANGLE,PRESSURE PRESSURE ANGLE A MEASUREMENT OF THE PRESSURE ANGLE ON THE ITEM. 1D AND 1A MODE REPLY13AJ40 BDZCJ /D/A04ANGLE,HELIX,TOOTH TOOTH HELIX ANGLE THE ANGULAR AMOUNT THE TEETH OF A RACK OR GEAR ARE INCLINED WITH RESPECT TO A LINE PERPENDICULAR TO THE EDGE OF THE GEAR. 1D AND 1A MODE REPLY13AJ40 BDZDJ /D/A04ANGLE,LEAD LEAD ANGLE THE ANGLE BETWEEN THE HELIX AND THE PLANE OF ROTATION OF A WORM GEAR. IT IS THE COMPLEMENT OF HELIX ANGLE COMMONLY USED IN SCREW THREAD PRACTICE. 1D AND 1A MODE REPLY13AJ40 BDZFJ /D/A04ANGLE,PITCH PITCH ANGLE THE ANGLE BETWEEN AN ELEMENT OF THE PITCH CONE OF A BEVEL GEAR AND ITS AXIS. 1D AND 1A MODE REPLY13AJ40 BDZGA /D/ 12QUANTITY,THREAD,GEAR GEAR THREAD QUANTITY THE NUMBER OF THREAD FORM(S) THAT PROGRESS HELICALLY AROUND THE GEAR AXIS. 1A MODE REPLY 0 BDZHJ /D/ 04RADIUS,THROAT THROAT RADIUS A MEASUREMENT OF THE CONCAVE CURVATURE ACROSS THE FACE OF A WORM GEAR OR WORM WHEEL. 2D AND 1B MODE REPLY21AA051AC20 BDZJD /D/ 05DIRECTION,TOOTH,GEAR GEAR TOOTH DIRECTION THE DIRECTION IN WHICH THE TEETH CURVE AWAY FROM THE AXIS WHEN VIEWED PARALLEL TO THE GEAR AXIS. SELECT REPLY CODE 10AA38 BDZKJ 10REPETITION RATE,PULSE PULSE REPETITION RATE THE AVERAGE RATE AT WHICH THE PULSES RECUR WITHIN A SPECIFIED TIME INTERVAL. 1D AND 1B MODE REPLY11AC11 BDZLJ /D/ 13THREAD LEAD,GEAR GEAR THREAD LEAD THE DISTANCE THAT ANY SINGLE THREAD WILL ADVANCE AXIALLY IN ONE COMPLETE REVOLUTION. 2D AND 1B MODE REPLY21AA051AC20 BDZMA /D/ 13THREAD LEAD QUANTITY,GEAR,MATING MATING GEAR THREAD LEAD QUANTITY THE NUMBER OF THREAD LEAD(S) ON THE WORM GEAR WITH WHICH THE WORM WHEEL WILL BE USED. 1A MODE REPLY 0 BDZND /D/ 08LOCATION,ACCOMMODATION,MOUNTING HOLE HEAD MOUNTING HOLE HEAD ACCOMMODATION LOCATION INDICATES THE LOCATION OF THE MOUNTING HOLE HEAD ACCOMMODATION ON THE ITEM. SELECT REPLY CODE 10AJ91 BDZPD 19CLASSIFICATION,QUALITY QUALITY CLASSIFICATION THE CLASSIFICATION WHICH IDENTIFIES THE QUALITY OF AN ITEM. SELECT REPLY CODE 10AE99 BDZQD 03DESIGNATION,BACKLASH BACKLASH DESIGNATION A DESIGNATION INDICATING THE BACKLASH QUALITY OF AN ITEM. SELECT REPLY CODE 10AE99 BDZRL /D/ 16STYLE,GROUPING,GEAR GEAR GROUPING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE GEAR GROUPING. 1L MODE REPLY 0 BDZSJ /D/ 04DIAMETER OF HUB BETWEEN FIRST AND SECOND GEAR DIAMETER OF HUB BETWEEN FIRST AND SECOND GEAR NONE. 2D AND 1B MODE REPLY21AA051AC20 BDZTJ /D/ 04DIAMETER OF HUB BETWEEN SECOND AND THIRD GEAR DIAMETER OF HUB BETWEEN SECOND AND THIRD GEAR NONE. 2D AND 1B MODE REPLY21AA051AC20 BDZWJ /D/ 04DIAMETER OF HUB BETWEEN THIRD AND FOURTH GEAR DIAMETER OF HUB BETWEEN THIRD AND FOURTH GEAR NONE. 2D AND 1B MODE REPLY21AA051AC20 BDZXJ /D/ 04LENGTH OF HUB BETWEEN FIRST AND SECOND GEAR LENGTH OF HUB BETWEEN FIRST AND SECOND GEAR NONE. 2D AND 1B MODE REPLY21AA051AC20 BDZYJ /D/ 04LENGTH OF HUB BETWEEN SECOND AND THIRD GEAR LENGTH OF HUB BETWEEN SECOND AND THIRD GEAR NONE. 2D AND 1B MODE REPLY21AA051AC20 BDZZJ /D/ 04LENGTH OF HUB BETWEEN THIRD AND FOURTH GEAR LENGTH OF HUB BETWEEN THIRD AND FOURTH GEAR NONE. 2D AND 1B MODE REPLY21AA051AC20 BEFRB /D/ 10EFFICACY FACTOR,BALLAST BALLAST EFFICACY FACTOR THE RATIO OF THE BALLAST FACTOR (RELATIVE LIGHT OUTPUT) TO INPUT WATTS OF POWER USED BY THE ITEM. 1B MODE REPLY 0 BFBBD /D/ 18TYPE,GEAR,FIRST FIRST GEAR TYPE INDICATES THE TYPE OF FIRST GEAR PROVIDED. SELECT REPLY CODE 10AC58 BFBCD /D/ 18TYPE,GEAR,SECOND SECOND GEAR TYPE INDICATES THE TYPE OF SECOND GEAR PROVIDED. SELECT REPLY CODE 10AC58 BFBDD /D/ 18TYPE,GEAR,THIRD THIRD GEAR TYPE INDICATES THE TYPE OF THIRD GEAR PROVIDED. SELECT REPLY CODE 10AC58 BFBFD /D/ 18TYPE,GEAR,FOURTH FOURTH GEAR TYPE INDICATES THE TYPE OF FOURTH GEAR PROVIDED. SELECT REPLY CODE 10AC58 BFBGF /D/T10RANGE IN PERCENT,HUMIDITY,STORAGE STORAGE HUMIDITY RANGE IN PERCENT THE MINIMUM AND MAXIMUM LIMITS OF HUMIDITY TO WHICH THE ITEM MAY BE SUBJECTED DURING STORAGE,EXPRESSED IN PERCENT OF RELATIVE HUMIDITY. 1F MODE REPLY 0 BFBHG /D/ 19FACILITY,FASTENING FASTENING FACILITY THE FACILITY/IES/ FOR FASTENING THE ITEM. FULL TEXT WRITE-IN 0 BFBJD /D/ 07CHAIN CHAIN AN INDICATION OF WHETHER OR NOT A CHAIN IS INCLUDED. SELECT REPLY CODE 10AA49 BFBKD 14SHAPE,APERTURE,DIAL DIAL APERTURE SHAPE THE PHYSICAL CONFIGURATION OF THE DIAL APERTURE. SELECT REPLY CODE 10AD07 BFBLG 04SIZE,APERTURE,DIAL DIAL APERTURE SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE DIAL APERTURE. FULL TEXT WRITE-IN 0 BFBMD /D/ 07FEATURE,CUTOUT,DIAL APERTURE KNOB DIAL APERTURE KNOB CUTOUT FEATURE AN INDICATION OF WHETHER OR NOT A KNOB CUTOUT FEATURE IS INCLUDED IN THE DIAL APERTURE. SELECT REPLY CODE 10AA49 BFBNA 12QUANTITY,CUTOUT,DIAL APERTURE KNOB DIAL APERTURE KNOB CUTOUT QUANTITY THE NUMBER OF KNOB CUTOUTS INCLUDED IN THE DIAL APERTURE. 1A MODE REPLY 0 BFBPG 04SIZE,CUTOUT,KNOB KNOB CUTOUT SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE KNOB CUTOUT(S). FULL TEXT WRITE-IN 0 BFBQG /D/ 08LOCATION,CUTOUT CUTOUT LOCATION INDICATES THE POSITION OF THE CUTOUT(S) ON THE ITEM. FULL TEXT WRITE-IN 0 BFBRA 12QUANTITY,GANG GANG QUANTITY THE NUMBER OF GANGS PROVIDED. 1A MODE REPLY 0 BFBSL 16STYLE DESIGNATOR,OPENING OPENING STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE OPENING. 1L MODE REPLY 0 BFBTD /D/ 07ADAPTER,INSULATING INSULATING ADAPTER AN INDICATION OF WHETHER OR NOT AN INSULATING ADAPTER IS INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA49 BFBWJ /D/ 04DISTANCE BETWEEN GANG CENTERS,HORIZONTAL HORIZONTAL DISTANCE BETWEEN GANG CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFBXJ 04HEIGHT,RAISE RAISE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BFBYJ 04DISTANCE BETWEEN OPENINGS,VERTICAL,CENTER TO CENTER CENTER TO CENTER VERTICAL DISTANCE BETWEEN OPENINGS THE CENTER TO CENTER VERTICAL DISTANCE BETWEEN OPENINGS. 2D AND 1B MODE REPLY21AA051AC20 BFBZJ /D/ 04DISTANCE BETWEEN GANG CENTERS,HORIZONTAL,CENTER TO CENTER CENTER TO CENTER HORIZONTAL DISTANCE BETWEEN GANG CENTERS THE CENTER TO CENTER HORIZONTAL DISTANCE BETWEEN GANG CENTERS. 2D AND 1B MODE REPLY21AA051AC20 BFCBA 12QUANTITY,INSULATOR INSULATOR QUANTITY THE NUMBER OF INSULATORS PROVIDED. 1A MODE REPLY 0 BFCCD 19NAME,INSULATOR INSULATOR NAME THE NOMENCLATURE BY WHICH THE INSULATOR IS IDENTIFIED. SELECT REPLY CODE 10AG25 BFCDD /D/ 07ADHESIVE ADHESIVE AN INDICATION OF WHETHER OR NOT ADHESIVE IS PROVIDED. SELECT REPLY CODE 10AB22 BFCFD 11METHOD,DRYING DRYING METHOD THE MEANS USED FOR DRYING THE ITEM. SELECT REPLY CODE 10AK63 BFCGD 07CHARACTERISTICS,CORROSIVE CORROSIVE CHARACTERISTICS AN INDICATION OF THE CORROSIVE CHARACTERISTICS OF THE ITEM. SELECT REPLY CODE 10AL63 BFCHB 10VOLTAGE RATING IN VOLTS PER MIL THICKNESS,DIELECTRIC MATERIAL,DRY DRY DIELECTRIC MATERIAL VOLTAGE RATING IN VOLTS PER MIL THICKNESS THE MAXIMUM POTENTIAL GRADIENT A DRY INSULATING MATERIAL CAN WITHSTAND WITHOUT RUPTURE,EXPRESSED IN VOLTS PER MIL (0.001 INCH) THICKNESS. 1B MODE REPLY 0 BFCJJ 10TEMP RATING IN DEG CELSIUS AT WHICH THE VOLTAGE TEST IS ESTABLISHED TEMP RATING IN DEG CELSIUS AT WHICH THE VOLTAGE TEST IS ESTABLISHED THE RATED TEMPERATURE AT WHICH THE VOLTAGE TEST IS ESTABLISHED,EXPRESSED IN DEGREES CELSIUS. 1D AND 1B MODE REPLY11AC20 BFCKD /D/ 07FEATURE,REINFORCEMENT REINFORCEMENT FEATURE AN INDICATION OF WHETHER OR NOT A REINFORCEMENT FEATURE IS PROVIDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AB22 BFCLA /D/ 16STYLE DESIGNATOR,LEG LEG STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LEG. 1A MODE REPLY 0 BFCMJ 04WIDTH,LEG LEG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFCNJ 04RADIUS,CORNER,LEG LEG CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFCPJ 04WIDTH AT LEG END WIDTH AT LEG END NONE. 2D AND 1B MODE REPLY21AA051AC20 BFCQJ /D/ 04LENGTH,LEG A LEG A LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFCRJ /D/ 04LENGTH,LEG B LEG B LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFCSJ /D/ 04THICKNESS,LEG A LEG A THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFCTJ /D/ 04THICKNESS,LEG B LEG B THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFCWJ 04DIAMETER/SIZE,HOLE HOLE DIAMETER/SIZE NONE. 2D AND 1B MODE REPLY21AA051AC20 BFCXJ 04DISTANCE BETWEEN HOLE CENTERS,HORIZONTAL HORIZONTAL DISTANCE BETWEEN HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFCYJ /D/ 04DISTANCE BETWEEN UPPER HOLE CENTERS,HORIZONTAL HORIZONTAL DISTANCE BETWEEN UPPER HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFCZJ /D/ 04DISTANCE BETWEEN LOWER HOLE CENTERS,HORIZONTAL HORIZONTAL DISTANCE BETWEEN LOWER HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFDBJ 04DISTANCE BETWEEN HOLE CENTERS,VERTICAL VERTICAL DISTANCE BETWEEN HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFDCJ 04DISTANCE BETWEEN FIRST AND SECOND HOLE CENTERS,HORIZONTAL HORIZONTAL DISTANCE BETWEEN FIRST AND SECOND HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFDDJ 04DISTANCE BETWEEN SECOND AND THIRD HOLE CENTERS,HORIZONTAL HORIZONTAL DISTANCE BETWEEN SECOND AND THIRD HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFDFJ 04DISTANCE BETWEEN FIRST AND SECOND HOLE CENTERS,VERTICAL VERTICAL DISTANCE BETWEEN FIRST AND SECOND HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFDGJ 04DISTANCE BETWEEN SECOND AND THIRD HOLE CENTERS,VERTICAL VERTICAL DISTANCE BETWEEN SECOND AND THIRD HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFDHD 19CONSTRUCTION,COVERING COVERING CONSTRUCTION THE STRUCTURAL CHARACTERISTIC(S) OF THE COVERING ON AN ITEM. SELECT REPLY CODE 10AD14 BFDJD /D/ 17SURFACE TREATMENT,WIRE WIRE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE WIRE SURFACE. SELECT REPLY CODE 10AD09 BFDKD 18TYPE,PROTRUSION PROTRUSION TYPE INDICATES THE TYPE OF PROTRUSION PROVIDED. SELECT REPLY CODE 10AJ54 BFDLD /D/ 07IMPREGNATION,COMPOUND,WEATHER SEALING WEATHER SEALING COMPOUND IMPREGNATION AN INDICATION OF WHETHER OR NOT WEATHER SEALING COMPOUND IMPREGNATION IS PROVIDED. SELECT REPLY CODE 10AB22 BFDMJ 10CAPACITY,PUMP PUMP CAPACITY THE RATED CAPACITY OF THE PUMP. 2D AND 1B MODE REPLY22AG671AC20 BFDND /D/ 07CORE,NONMETALLIC NONMETALLIC CORE AN INDICATION OF WHETHER OR NOT A NONMETALLIC CORE IS PROVIDED. SELECT REPLY CODE 10AB22 BFDPB /D/ 10SPEED IN RPM,OPERATING OPERATING SPEED IN RPM THE RATED SPEED OF THE ITEM,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 BFDQB 10SPEED IN RPM,OPERATING,ELECTRIC MOTOR ELECTRIC MOTOR OPERATING SPEED IN RPM THE RATED SPEED OF THE ELECTRIC MOTOR,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 BFDRD /D/ 07INSERT INSERT AN INDICATION OF WHETHER OR NOT AN INSERT IS INCLUDED. SELECT REPLY CODE 10AA49 BFDSJ 04DISTANCE BETWEEN FULCRUM AND AA ARM END HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FULCRUM AND AA ARM END HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BFDTJ /D/ 04DISTANCE BETWEEN FULCRUM AND AA ARM END SLOT,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FULCRUM AND AA ARM END SLOT NONE. 2D AND 1B MODE REPLY21AA051AC20 BFDWJ /D/ 04DISTANCE BETWEEN FULCRUM AND AA ARM END BALL,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FULCRUM AND AA ARM END BALL NONE. 2D AND 1B MODE REPLY21AA051AC20 BFDXJ /D/ 04DISTANCE BETWEEN FULCRUM AND AA ARM END SHAFT,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FULCRUM AND AA ARM END SHAFT NONE. 2D AND 1B MODE REPLY21AA051AC20 BFDYJ 04RADIUS,END,AA ARM AA ARM END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFDZJ 04DIAMETER,HOLE,AA ARM END AA ARM END HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFFBJ /D/ 04DIAMETER,END,BALL,AA ARM AA ARM BALL END DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFFCJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,HOLE,END,AA ARM AA ARM END HOLE THREAD SIZE AND SERIES/TYPE DESIGNATOR NONE. 1D AND 1A MODE REPLY12AH06 BFFDJ 04DISTANCE BETWEEN FULCRUM AND BB ARM END HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FULCRUM AND BB ARM END HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BFFFJ 04DISTANCE BETWEEN FULCRUM AND BB ARM END SLOT,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FULCRUM AND BB ARM END SLOT NONE. 2D AND 1B MODE REPLY21AA051AC20 BFFGJ /D/ 04DISTANCE BETWEEN FULCRUM AND BB ARM END BALL,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FULCRUM AND BB ARM END BALL NONE. 2D AND 1B MODE REPLY21AA051AC20 BFFHJ /D/ 04DISTANCE BETWEEN FULCRUM AND BB ARM END SHAFT,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FULCRUM AND BB ARM END SHAFT NONE. 2D AND 1B MODE REPLY21AA051AC20 BFFJJ 04RADIUS,END,BB ARM BB ARM END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFFKJ 04DIAMETER,HOLE,SECOND,BB ARM BB ARM SECOND HOLE DIAMETER NONE. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 2D AND 1B MODE REPLY21AA051AC20 BFFLJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,HOLE,SECOND,BB ARM BB ARM SECOND HOLE THREAD SIZE AND SERIES/TYPE DESIGNATOR NONE. 1D AND 1A MODE REPLY12AH06 BFFMJ /D/ 04DIAMETER,HOLE,SECOND,AA ARM AA ARM SECOND HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFFNJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,HOLE,SECOND,AA ARM AA ARM SECOND HOLE THREAD SIZE AND SERIES/TYPE DESIGNATOR NONE. 1D AND 1A MODE REPLY12AH06 BFFPJ 04THICKNESS,END,AA ARM AA ARM END THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFFQJ /D/ 04DISTANCE BETWEEN FULCRUM AND AA ARM SECOND HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FULCRUM AND AA ARM SECOND HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BFFRJ /D/ 04LENGTH,SLOT,AA ARM END AA ARM END SLOT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFFSJ /D/ 04WIDTH,SLOT,AA ARM SECOND AA ARM SECOND SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFFTJ 04DISTANCE BETWEEN FULCRUM AND BB ARM SECOND HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FULCRUM AND BB ARM SECOND HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BFFWJ 04THICKNESS,AA ARM AA ARM THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFFXJ 04THICKNESS,BB ARM BB ARM THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFFYJ /D/ 04DISTANCE,OFFSET,AA ARM AA ARM OFFSET DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 BFFZB /D/ 04ANGLE IN DEG,OFFSET,AA ARM AA ARM OFFSET ANGLE IN DEG NONE. 1B MODE REPLY 0 BFGBJ /D/ 04DISTANCE,OFFSET,BB ARM BB ARM OFFSET DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 BFGCB /D/ 04ANGLE IN DEG,OFFSET,BB ARM BB ARM OFFSET ANGLE IN DEG NONE. 1B MODE REPLY 0 BFGDG /D/ 13THREAD CHARACTERISTICS,OUTSIDE OUTSIDE THREAD CHARACTERISTICS NONE. FULL TEXT WRITE-IN 0 BFGFJ /D/ 04DEPTH,SLOT,AA ARM AA ARM SLOT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFGGJ /D/ 04DIAMETER,SHAFT,END END SHAFT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFGHD /D/ 07FEATURE,REINFORCEMENT,WIRE MESH WIRE MESH REINFORCEMENT FEATURE AN INDICATION OF WHETHER OR NOT A WIRE MESH REINFORCEMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BFGJJ /D/T12QUANTITY,MESH MESH QUANTITY THE NUMBER OF MESH IN A LONGITUDINAL AND TRANSVERSE DIRECTION PER SPECIFIC MEASUREMENT SCALE. 1D AND 1F MODE REPLY11AB39 BFGKJ /D/ 04DIAMETER,INSIDE,HUB HUB INSIDE DIAMETER NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 BFGLJ /D/ 04DIAMETER,OUTSIDE,HUB HUB OUTSIDE DIAMETER NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 BFGMJ /D/ 04LENGTH,OVERALL OVERALL LENGTH NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 BFGNJ /D/ 04DISTANCE FROM HUB END TO SHOULDER DISTANCE FROM HUB END TO SHOULDER NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 BFGPJ /D/ 04WIDTH,SHOULDER SHOULDER WIDTH NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 BFGQJ /D/ 04DIAMETER,OUTSIDE,SHOULDER SHOULDER OUTSIDE DIAMETER NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 BFGRJ /D/ 13THREAD LENGTH THREAD LENGTH NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 BFGSG 04SIZE,HOLE,SECURING SECURING HOLE SIZE NONE. FULL TEXT WRITE-IN 0 BFGTJ /D/ 04LENGTH TO JOINT LENGTH TO JOINT NONE. 2D AND 1B MODE REPLY21AA051AC20 BFGWJ 04DISTANCE BETWEEN LINK AND SHAFT HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN LINK AND SHAFT HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 BFGXJ 04THICKNESS,END,SHAFT SHAFT END THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFGYJ 04THICKNESS,END,LINK LINK END THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFGZJ 04DIAMETER,HOLE,FIRST,LINK END LINK END FIRST HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFHAJ 04DIAMETER,HOLE,LINK END LINK END HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFHBJ /D/ 04DIAMETER,HOLE,SECOND,LINK END LINK END SECOND HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFHCJ /D/ 04DIAMETER,HOLE,THIRD,LINK END LINK END THIRD HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFHDJ /D/ 04DISTANCE FROM FIRST LINK HOLE CENTER TO END DISTANCE FROM FIRST LINK HOLE CENTER TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 BFHFJ 04DISTANCE FROM SHAFT HOLE CENTER TO END DISTANCE FROM SHAFT HOLE CENTER TO END THE DISTANCE FROM THE SHAFT HOLE CENTER TO THE END. 2D AND 1B MODE REPLY21AA051AC20 BFHGJ /D/ 04DISTANCE BETWEEN FIRST AND SECOND LINK END HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FIRST AND SECOND LINK END HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 BFHHJ /D/ 04DISTANCE BETWEEN SECOND AND THIRD LINK END HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SECOND AND THIRD LINK END HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 BFHJJ /D/ 04DISTANCE BETWEEN SHAFT AND LINK END HOLES,OFFSET,CENTER TO CENTER CENTER TO CENTER OFFSET DISTANCE BETWEEN SHAFT AND LINK END HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 BFHKJ 04DIAMETER,HOLE,SECURING SECURING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFHLJ /D/ 04DIAMETER,HOLE,CLAMP CLAMP HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFHMA 12QUANTITY,MARKING,LINE LINE MARKING QUANTITY THE NUMBER OF LINES THE ITEM WILL MARK. 1A MODE REPLY 0 BFHNJ 04DISTANCE BETWEEN FORK INSIDE SPREAD DISTANCE BETWEEN FORK INSIDE SPREAD NONE. 2D AND 1B MODE REPLY21AA051AC20 BFHPJ /D/ 04THICKNESS,TONGUE,FORK FORK TONGUE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFHQJ /D/ 04RADIUS,END,LINK LINK END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFHRJ /D/ 04RADIUS,END,SHAFT SHAFT END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFHSD 11METHOD,FABRICATION,JACKET JACKET FABRICATION METHOD THE PROCESS USED IN MANUFACTURING THE JACKET. SELECT REPLY CODE 10AA62 BFHTD /D/ 11METHOD,LAYING LAYING METHOD THE MANNER IN WHICH THE ITEM IS TO BE LAID. SELECT REPLY CODE 10AN03 BFHWG /D/ 19DIMENSION,AREA,EXPOSED EXPOSED AREA DIMENSION A MEASUREMENT OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE EXPOSED AREA. FULL TEXT WRITE-IN 0 BFHXD /D/ 02DESIGN,EDGE,BUTT BUTT EDGE DESIGN THE DESIGN OF THE BUTT EDGE. SELECT REPLY CODE 10AL25 BFHYD /D/ 07SURFACE,GRAINED GRAINED SURFACE AN INDICATION OF WHETHER OR NOT A GRAINED SURFACE IS INCLUDED. SELECT REPLY CODE 10AA49 BFHZD 18TYPE,MEASUREMENT MEASUREMENT TYPE INDICATES THE TYPE OF MEASUREMENT PROVIDED. SELECT REPLY CODE 10AJ52 BFJBJ /D/T10RANGE,FREQUENCY FREQUENCY RANGE THE RANGE OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE ITEM IS RATED. 2D AND 1F MODE REPLY21AC323AK54 BFJCG 10ACCURACY RATING ACCURACY RATING AN INDICATION OF THE DEVIATION FROM A STANDARD OR TRUE VALUE FOR WHICH THE ITEM IS RATED. FULL TEXT WRITE-IN 0 BFJDJ 04WIDTH,SURFACE,LAPPING LAPPING SURFACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A LAPPING SURFACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BFJFJ 10TIME,GATE GATE TIME THE INTERVAL OF TIME DURING WHICH THE ITEM PROVIDES A SIGNAL. 2D AND 1B MODE REPLY22AB491AC20 BFJGG /D/ 10SENSITIVITY RATING SENSITIVITY RATING THE RATED SENSITIVITY OF THE ITEM. FULL TEXT WRITE-IN 0 BFJHJ /D/ 04LENGTH,SHAFT,END END SHAFT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFJJJ /D/ 04DISTANCE BETWEEN END HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN END HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 BFJKJ 04DIAMETER,HOLE,BB ARM END BB ARM END HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFJLJ /D/ 04DIAMETER,END,BALL,BB ARM BB ARM BALL END DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFJMJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,HOLE,END,BB ARM BB ARM END HOLE THREAD SIZE AND SERIES/TYPE DESIGNATOR NONE. 1D AND 1A MODE REPLY12AH06 BFJNJ /D/ 04DIAMETER,HOLE,THIRD,BB ARM BB ARM THIRD HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFJPJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,HOLE,THIRD,BB ARM BB ARM THIRD HOLE THREAD SIZE AND SERIES/TYPE DESIGNATOR NONE. 1D AND 1A MODE REPLY12AH06 BFJQJ /D/ 04DIAMETER,HOLE,THIRD,AA ARM AA ARM THIRD HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFJRJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,HOLE,THIRD,AA ARM AA ARM THIRD HOLE THREAD SIZE AND SERIES/TYPE DESIGNATOR NONE. 1D AND 1A MODE REPLY12AH06 BFJSJ 04THICKNESS,END,BB ARM BB ARM END THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFJTJ /D/ 04DISTANCE BETWEEN FULCRUM AND AA ARM THIRD HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FULCRUM AND AA ARM THIRD HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BFJWJ /D/ 04LENGTH,SLOT,BB ARM END BB ARM END SLOT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFJXJ /D/ 04WIDTH,SLOT,BB ARM BB ARM SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFJYJ /D/ 04DISTANCE BETWEEN FULCRUM AND BB ARM THIRD HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FULCRUM AND BB ARM THIRD HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BFJZJ /D/ 04THICKNESS,END,LARGER,AA ARM AA ARM LARGER END THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFKBJ /D/ 04THICKNESS,END,LARGER,BB ARM BB ARM LARGER END THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFKCG /D/ 13THREAD CHARACTERISTICS,INSIDE INSIDE THREAD CHARACTERISTICS NONE. FULL TEXT WRITE-IN 0 BFKDJ /D/ 04DEPTH,SLOT,BB ARM BB ARM SLOT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFKFJ /D/ 04DISTANCE FROM PIVOT HOLE CENTER TO TOOTH PROFILE MAJOR DIAMETER DISTANCE FROM PIVOT HOLE CENTER TO TOOTH PROFILE MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFKGJ /D/ 04RADIUS,MAJOR MAJOR RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFKHJ /D/ 04DIAMETER,TONGUE TONGUE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFKJJ 04LENGTH FROM PIVOT PINHOLE CENTERLINE TO POINT OF ENGAGEMENT LENGTH FROM PIVOT PINHOLE CENTERLINE TO POINT OF ENGAGEMENT NONE. 2D AND 1B MODE REPLY21AA051AC20 BFKKJ /D/ 04DEPTH FROM PIVOT PINHOLE CENTERLINE TO POINT OF ENGAGEMENT DEPTH FROM PIVOT PINHOLE CENTERLINE TO POINT OF ENGAGEMENT NONE. 2D AND 1B MODE REPLY21AA051AC20 BFKLJ /D/ 04LENGTH FROM PIVOT PINHOLE CENTER TO ENGAGEMENT END LENGTH FROM PIVOT PINHOLE CENTER TO ENGAGEMENT END NONE. 2D AND 1B MODE REPLY21AA051AC20 BFKMJ /D/ 04LENGTH,OPENING,ATTACHMENT ATTACHMENT OPENING LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFKNJ /D/ 04WIDTH,OPENING,ATTACHMENT ATTACHMENT OPENING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFKPB /D/ 04ANGLE IN DEG,OPENING OPENING ANGLE IN DEG NONE. 1B MODE REPLY 0 BFKQJ /D/ 04LENGTH FROM ATTACHMENT OPENING CENTER TO ENGAGEMENT END LENGTH FROM ATTACHMENT OPENING CENTER TO ENGAGEMENT END NONE. 2D AND 1B MODE REPLY21AA051AC20 BFKRJ /D/ 04DISTANCE FROM END TO SHOULDER DISTANCE FROM END TO SHOULDER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFKSA /D/ 12QUANTITY,FLATS FLATS QUANTITY NONE. 1A MODE REPLY 0 BFKTJ 04DISTANCE FROM END TO HOLE CENTER DISTANCE FROM END TO HOLE CENTER THE DISTANCE FROM THE END OF THE ITEM TO THE CENTER OF THE HOLE. 2D AND 1B MODE REPLY21AA051AC20 BFKWJ /D/ 04DISTANCE FROM HOLE CENTER TO OFFSET DISTANCE FROM HOLE CENTER TO OFFSET NONE. 2D AND 1B MODE REPLY21AA051AC20 BFKXJ /D/ 04DISTANCE FROM END TO UNDERCUT DISTANCE FROM END TO UNDERCUT NONE. 2D AND 1B MODE REPLY21AA051AC20 BFKYJ /D/ 04DISTANCE BETWEEN END HOLE AND INTERMEDIATE HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN END HOLE AND INTERMEDIATE HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BFKZJ 04RADIUS,CORNER,BODY BODY CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFLBJ /D/ 04DISTANCE BETWEEN CONNECTING END HOLE CENTERS,OFFSET OFFSET DISTANCE BETWEEN CONNECTING END HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFLCJ /D/ 04DISTANCE FROM HOLE CENTER TO BODY DISTANCE FROM HOLE CENTER TO BODY NONE. 2D AND 1B MODE REPLY21AA051AC20 BFLDJ 04DIAMETER,HOLE,END ATTACHMENT END ATTACHMENT HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFLFJ /D/ 04LENGTH,CHAMFER,END ATTACHMENT END ATTACHMENT CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 BFLGB /D/ 04ANGLE IN DEG,CHAMFER,END ATTACHMENT END ATTACHMENT CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 BFLHJ /D/ 04RADIUS,END,END ATTACHMENT END ATTACHMENT END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFLJD 02DESIGN,STOWAGE,BULK BULK STOWAGE DESIGN THE BULK STOWAGE DESIGN OF THE ITEM. SELECT REPLY CODE 10AK54 BFLKL 16STYLE,STOVE STOVE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE STOVE. 1L MODE REPLY 0 BFLLD /D/ 07WINDSHIELD,HINGED,SEPARATE SEPARATE HINGED WINDSHIELD AN INDICATION OF WHETHER OR NOT A SEPARATE HINGED WINDSHIELD IS PROVIDED. SELECT REPLY CODE 10AB22 BFLMD /D/ 07COVER,BURNER,SEPARATE CUP LIKE SEPARATE CUP LIKE BURNER COVER AN INDICATION OF WHETHER OR NOT A SEPARATE CUP LIKE BURNER COVER IS PROVIDED. SELECT REPLY CODE 10AB22 BFLND /D/ 07GRATE,FOLDING,INDEPENDENT INDEPENDENT FOLDING GRATE AN INDICATION OF WHETHER OR NOT AN INDEPENDENT FOLDING GRATE IS PROVIDED. SELECT REPLY CODE 10AB22 BFLPJ /D/ 10POWER RATING,OUTPUT OUTPUT POWER RATING THE OUTPUT POWER AT WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY11AC33 BFLQB 10SPEED IN RPM,CALIBRATION CALIBRATION SPEED IN RPM THE SPEED AT WHICH THE CALIBRATION IS DETERMINED,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 BFLRB /D/ 10FREQUENCY RATING IN HERTZ,OUTPUT OUTPUT FREQUENCY RATING IN HERTZ THE CYCLES PER SECOND /HERTZ/ OF THE OUTPUT ALTERNATING CURRENT. 1B MODE REPLY 0 BFLSD 10PHASE,OUTPUT OUTPUT PHASE THE NUMBER OF OUTPUT ALTERNATING CURRENT PHASES. SELECT REPLY CODE 10AD02 BFLTJ 10INTERVAL,TIME TIME INTERVAL THE ACCEPTABLE TIME LIMITS FOR THE ITEM. 2D AND 1B MODE REPLY22AH683AN04 BFLWH /D/ 19POWER AND TRANSFER METHOD,MECHANICAL MECHANICAL POWER AND TRANSFER METHOD THE MECHANICAL POWER PROVIDED AND THE MEANS BY WHICH IT IS TRANSFERRED TO OR FROM THE ITEM. 2D MODE REPLY 23AM392AK43 BFLXA 12QUANTITY,HOLE,COUPLING COUPLING HOLE QUANTITY THE NUMBER OF COUPLING HOLES PROVIDED. 1A MODE REPLY 0 BFLYD 19POSITION,ALIGNMENT,OUTPUT SHAFT GEARED HEAD GEARED HEAD OUTPUT SHAFT ALIGNMENT POSITION THE DRIVE SHAFT POSITION AS RELATED TO THE ARMATURE AXIS. SELECT REPLY CODE 10AM84 BFLZB /D/ 04ANGLE OF SHAFT TO ROTOR AXIS IN DEG ANGLE OF SHAFT TO ROTOR AXIS IN DEG THE ANGLE OF THE SHAFT IN RELATION TO THE ROTOR AXIS,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BFMBB /D/ 04ANGLE OF SHAFT TO MOUNTING BASE IN DEG ANGLE OF SHAFT TO MOUNTING BASE IN DEG THE ANGLE OF THE SHAFT IN RELATION TO THE MOUNTING BASE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BFMCD /D/ 18TYPE,INDICATOR,SPEED SPEED INDICATOR TYPE INDICATES THE TYPE OF SPEED INDICATOR USED WITH THE ITEM. SELECT REPLY CODE 10AJ12 BFMFD 11METHOD,COOLING COOLING METHOD THE MEANS OF COOLING USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE ITEM. SELECT REPLY CODE 10AN05 BFMGD /D/ 07DEVICE,PROTECTIVE,THERMAL THERMAL PROTECTIVE DEVICE AN INDICATION OF WHETHER OR NOT A THERMAL PROTECTIVE DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 BFMHD /D/ 07FEATURE,FRAME,ELECTRICAL ELECTRICAL FRAME FEATURE AN INDICATION OF WHETHER OR NOT AN ELECTRICAL FRAME FEATURE IS INCLUDED. SELECT REPLY CODE 10AB87 BFMJB 10CURRENT RATING IN AMPS,FIELD,CONTROL CONTROL FIELD CURRENT RATING IN AMPS THE CURRENT RATING OF THE CONTROL FIELD,EXPRESSED IN AMPERES. 1B MODE REPLY 0 BFMKB 10IMPEDANCE RATING IN OHMS,FIELD,CONTROL CONTROL FIELD IMPEDANCE RATING IN OHMS THE IMPEDANCE RATING OF THE CONTROL FIELD,EXPRESSED IN OHMS. 1B MODE REPLY 0 BFMLD 18TYPE,WINDING,CONTROL FIELD CONTROL FIELD WINDING TYPE INDICATES THE TYPE OF WINDING(S) OF THE CONTROL FIELD. SELECT REPLY CODE 10AC02 BFMMB /D/ 10VOLTAGE RATING IN VOLTS,DC,ARMATURE ARMATURE DC VOLTAGE RATING IN VOLTS THE DIRECT CURRENT VOLTAGE RATING OF THE ARMATURE,EXPRESSED IN VOLTS. 1B MODE REPLY 0 BFMND /D/ 07ADAPTABILITY,PHASE,SINGLE SINGLE PHASE ADAPTABILITY AN INDICATION OF WHETHER OR NOT THE ITEM IS ADAPTABLE TO OPERATE WITH A SINGLE PHASE. SELECT REPLY CODE 10AJ23 BFMPD /D/ 07CAPABILITY,FEEDBACK,CURRENT CURRENT FEEDBACK CAPABILITY AN INDICATION OF WHETHER OR NOT A CURRENT FEEDBACK CAPABILITY IS INCLUDED. SELECT REPLY CODE 10AA49 BFMQJ 04DISTANCE,FLAT CENTER TO SHAFT END FLAT CENTER TO SHAFT END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 BFMRJ 04DISTANCE,KEYWAY CENTER TO SHAFT END KEYWAY CENTER TO SHAFT END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 BFMSJ 04LENGTH,TOOTH,FULL FULL TOOTH LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFMTJ 04LENGTH,KNURL KNURL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFMWJ 04DIAMETER,COUPLING COUPLING DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFMXJ 04DISTANCE,SECOND HOLE CENTER TO SHAFT END SECOND HOLE CENTER TO SHAFT END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 BFMYJ 04DISTANCE,FIRST HOLE CENTER TO SHAFT END FIRST HOLE CENTER TO SHAFT END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 BFMZJ 04DEPTH,HOLE,SECOND SECOND HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFNBJ 04DEPTH,HOLE,FIRST FIRST HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFNCJ 04DISTANCE,SECOND KEYWAY CENTER TO SHAFT END SECOND KEYWAY CENTER TO SHAFT END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 BFNDJ 04DEPTH,KEYWAY,SECOND SECOND KEYWAY DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFNFJ 04DISTANCE,UNDERCUT CENTER TO SHAFT END UNDERCUT CENTER TO SHAFT END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 BFNGJ 04HEIGHT ABOVE SHAFT,KEY KEY HEIGHT ABOVE SHAFT NONE. 2D AND 1B MODE REPLY21AA051AC20 BFNHJ /D/ 04RADIUS,CORNER,END ATTACHMENT END ATTACHMENT CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BFNJJ /D/ 04DEPTH,FORK,ATTACHMENT,END END ATTACHMENT FORK DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFNKJ /D/ 04HEIGHT,ATTACHMENT,END END ATTACHMENT HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BFNLJ 04LENGTH,ATTACHMENT,END END ATTACHMENT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFNMJ /D/ 04DISTANCE FROM FORK END TO HOLE CENTER DISTANCE FROM FORK END TO HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 BFNNJ /D/ 04WIDTH,SPAN,END ATTACHMENT FORK END ATTACHMENT FORK SPAN WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFNPJ 04WIDTH,FORK,END ATTACHMENT END ATTACHMENT FORK WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFNQJ 04WIDTH,ATTACHMENT,END END ATTACHMENT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFNRD 18TYPE,RACK RACK TYPE INDICATES THE TYPE OF RACK PROVIDED. SELECT REPLY CODE 10AK54 BFNSA 12QUANTITY ACCOMMODATED,CYLINDER CYLINDER QUANTITY ACCOMMODATED THE NUMBER OF CYLINDER(S) THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 BFNTD /D/ 07BODY,TYPE,VAN VAN TYPE BODY AN INDICATION OF WHETHER OR NOT A VAN TYPE BODY IS PROVIDED. SELECT REPLY CODE 10AB22 BFNWD /D/ 07DOLLY DOLLY AN INDICATION OF WHETHER OR NOT A DOLLY IS PROVIDED. SELECT REPLY CODE 10AB22 BFNXD 18TYPE,MOVER,PRIME,COMPRESSOR COMPRESSOR PRIME MOVER TYPE INDICATES THE TYPE OF PRIME MOVER INCLUDED WITH THE COMPRESSOR. SELECT REPLY CODE 10AG27 BFNYD /D/ 07GENERATOR,ELECTRIC ELECTRIC GENERATOR AN INDICATION OF WHETHER OR NOT AN ELECTRIC GENERATOR IS INCLUDED. SELECT REPLY CODE 10AA49 BFNZJ 10CAPACITY AND TYPE,GENERATING,GAS GAS GENERATING CAPACITY AND TYPE INDICATES THE AMOUNT AND TYPE OF GAS THE ITEM CAN GENERATE. 2D AND 1B MODE REPLY22AG672AB75 BFPBJ 04DIAMETER,FRAME FRAME DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FRAME,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BFPCJ 04DEPTH,FRAME FRAME DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON A FRAME,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BFPDD /D/ 09MATERIAL,SCREEN SCREEN MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SCREEN IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BFPFJ 04DIAMETER,WIRE,REINFORCEMENT REINFORCEMENT WIRE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A REINFORCEMENT WIRE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BFPGJ /D/ 10CAPACITY FOR WHICH DESIGNED,BOWL,LADLE LADLE BOWL CAPACITY FOR WHICH DESIGNED THE CAPACITY OF THE LADLE BOWL FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY12AG67 BFPHD /D/ 07BAND,FLUTED FLUTED BAND AN INDICATION OF WHETHER OR NOT A FLUTED BAND IS INCLUDED. SELECT REPLY CODE 10AA49 BFPJD /D/ 07TONGS TONGS AN INDICATION OF WHETHER OR NOT TONGS ARE INCLUDED. SELECT REPLY CODE 10AA49 BFPKA /D/ 12QUANTITY,TONGS TONGS QUANTITY THE NUMBER OF TONG(S) INCLUDED. 1A MODE REPLY 0 BFPLL /D/ 16STYLE,TONGS TONGS STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TONGS. 1L MODE REPLY 0 BFPMD /D/ 07CORNERS,ROUNDED ROUNDED CORNERS AN INDICATION OF WHETHER OR NOT ROUNDED CORNERS ARE PROVIDED. SELECT REPLY CODE 10AB22 BFPND 19CONDITION,SURFACE,RUBBER SHEETING RUBBER SHEETING SURFACE CONDITION THE CONDITION OF THE RUBBER SHEETING WITH RESPECT TO THE TEXTURE OF THE SURFACE. SELECT REPLY CODE 10AK39 BFPPD 05DIRECTION,BEND BEND DIRECTION AN INDICATION OF THE BEND DIRECTION IN RELATION TO THE ITEM. SELECT REPLY CODE 10AL96 BFPQD 02DESIGN,CORRUGATION CORRUGATION DESIGN THE DESIGN FORMED BY THE CORRUGATIONS. SELECT REPLY CODE 10AK54 BFPRD /D/ 09MATERIAL,PILE PILE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PILE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BFPSD /D/ 09MATERIAL,STUFFERS STUFFERS MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE STUFFERS ARE FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BFPTJ A12QUANTITY,ROW ROW QUANTITY THE NUMBER OF ROW(S) PER UNIT OF MEASURE. 1D AND 1A MODE REPLY12AG67 BFPWJ A12QUANTITY,WIRE WIRE QUANTITY THE NUMBER OF WIRES PER UNIT OF MEASURE. 1D AND 1A MODE REPLY12AG67 BFPXJ A12QUANTITY,WALE WALE QUANTITY THE NUMBER OF WALES PER UNIT OF MEASURE. 1D AND 1A MODE REPLY12AG67 BFPYD 18TYPE,FINISH,SIDE SIDE FINISH TYPE INDICATES THE TYPE OF FINISH USED ON THE SIDE(S) OF THE ITEM. SELECT REPLY CODE 10AL59 BFPZD 18TYPE,FINISH,END END FINISH TYPE INDICATES THE TYPE OF FINISH USED ON THE END(S) OF THE ITEM. SELECT REPLY CODE 10AL59 BFQBA 12QUANTITY PER 27 INCH WIDTH,END,PILE PILE END QUANTITY PER 27 INCH WIDTH THE NUMBER OF PILE ENDS IN A STANDARD 27 INCH WIDTH. 1A MODE REPLY 0 BFQCJ 10WEIGHT PER CARPET YARD WEIGHT PER CARPET YARD INDICATES THE WEIGHT OF THE ITEM PER CARPET YARD. 2D AND 1B MODE REPLY22AG671AC20 BFQDB 10PERCENT TO CARPET YARD TOTAL WEIGHT,MINIMUM,PILE WEIGHT PILE WEIGHT MINIMUM PERCENT TO CARPET YARD TOTAL WEIGHT AN INDICATION OF THE LOWEST PERCENTAGE OF PILE WEIGHT PERMISSIBLE TO THE TOTAL WEIGHT PER CARPET YARD. 1B MODE REPLY 0 BFQFJ 04HEIGHT,PILE PILE HEIGHT A MEASUREMENT TAKEN FROM THE TOP SURFACE OF THE BACK TO THE TOP SURFACE OF THE PILE. 2D AND 1B MODE REPLY21AA051AC20 BFQGJ 10WEIGHT,PILE PILE WEIGHT THE WEIGHT OF THE PILE WITHIN A SPECIFIED AREA. 3D AND 1B MODE REPLY32AG671AC201AB39 BFQHG /D/ 19DISPLAY,RATIO RATIO DISPLAY THE VISUAL PRESENTATION OF THE RATIO INFORMATION. FULL TEXT WRITE-IN 0 BFQJF T10RANGE,PERIOD PERIOD RANGE THE MINIMUM AND MAXIMUM NUMBER OF PERIODS. 1F MODE REPLY 0 BFQKJ A12QUANTITY,STEP,PERIOD RANGE PERIOD RANGE STEP QUANTITY THE NUMBER OF PERIOD RANGE STEPS PROVIDED. 1D AND 1A MODE REPLY13AJ12 BFQLJ /D/ 10COUNT RATE COUNT RATE AN INDICATION OF THE COUNT RATE OF THE ITEM. 3D AND 1B MODE REPLY31AC321AC203AK54 BFQMD /D/ 07FEATURE,CALIBRATION,INTERNAL INTERNAL CALIBRATION FEATURE AN INDICATION OF WHETHER OR NOT AN INTERNAL CALIBRATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BFQND 18TYPE,DISPLAY DISPLAY TYPE INDICATES THE TYPE OF DISPLAY PROVIDED. SELECT REPLY CODE 10AK54 BFQPA 12QUANTITY,DIGIT,DISPLAY DISPLAY DIGIT QUANTITY THE NUMBER OF DIGITS DISPLAYED. 1A MODE REPLY 0 BFQQD /D/ 07INDICATOR,UNITS,DISPLAY DISPLAY UNITS INDICATOR AN INDICATION OF WHETHER OR NOT A DISPLAY UNITS INDICATOR IS INCLUDED. SELECT REPLY CODE 10AA49 BFQRD /D/ 07POINT,DECIMAL,DISPLAY POSITIONED DISPLAY POSITIONED DECIMAL POINT AN INDICATION OF WHETHER OR NOT A DISPLAY POSITIONED DECIMAL POINT IS PROVIDED. SELECT REPLY CODE 10AB22 BFQSD /D/ 07FACILITY,STORAGE,DISPLAY DISPLAY STORAGE FACILITY AN INDICATION OF WHETHER OR NOT A DISPLAY STORAGE FACILITY IS INCLUDED. SELECT REPLY CODE 10AA49 BFQTD /D/ 07PROVISIONS,CONTROL,REMOTE REMOTE CONTROL PROVISIONS AN INDICATION OF WHETHER OR NOT PROVISIONS FOR REMOTE CONTROL ARE INCLUDED. SELECT REPLY CODE 10AA49 BFQWD /D/ 07FEATURE,STATE,SOLID SOLID STATE FEATURE AN INDICATION OF WHETHER OR NOT A SOLID STATE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BFQXH /D/ 09MATERIAL AND LOCATION,INCLOSURE INCLOSURE MATERIAL AND LOCATION THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INCLOSURE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT,AND ITS LOCATION. 2D MODE REPLY 26AD093AJ91 BFQYH /D/ 17SURFACE TREATMENT AND LOCATION,INCLOSURE INCLOSURE SURFACE TREATMENT AND LOCATION CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE INCLOSURE SURFACE,AND ITS LOCATION. 2D MODE REPLY 26AD093AJ91 BFQZD /D/ 07PROVISION,UNITS,PLUG-IN PLUG-IN UNITS PROVISION AN INDICATION OF WHETHER OR NOT A PROVISION FOR PLUG-IN UNITS IS INCLUDED. SELECT REPLY CODE 10AA49 BFRBD /D/ 07FEATURE,OUTPUT,STANDARD FREQUENCY STANDARD FREQUENCY OUTPUT FEATURE AN INDICATION OF WHETHER OR NOT A STANDARD FREQUENCY/IES/ OUTPUT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BFRCG /D/ 10ACCURACY/STABILITY,FREQUENCY FREQUENCY ACCURACY/STABILITY AN INDICATION OF THE ALLOWABLE FREQUENCY ACCURACY OR STABILITY OF THE ITEM. FULL TEXT WRITE-IN 0 BFRDD 19WAVEFORM,FREQUENCY,OUTPUT OUTPUT FREQUENCY WAVEFORM THE SHAPE OF THE OUTPUT FREQUENCY WAVEFORM. SELECT REPLY CODE 10AJ52 BFRFJ 10AMPLITUDE,OUTPUT,FREQUENCY FREQUENCY OUTPUT AMPLITUDE THE MAXIMUM ABSOLUTE VALUE OF THE FREQUENCY OUTPUT PULSE. 2D AND 1B MODE REPLY21AB631AF65 BFRGD /D/ 07POCKET,LINE,LOWERING LOWERING LINE POCKET AN INDICATION OF WHETHER OR NOT A LOWERING LINE POCKET IS INCLUDED. SELECT REPLY CODE 10AA49 BFRHJ 04LENGTH,OPENING OPENING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE OPENING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BFRJJ T04LENGTH,ADJUSTABLE ADJUSTABLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION TO WHICH THE ITEM MAY BE ADJUSTED,IN DISTINCTION FROM WIDTH. 1D AND 1F MODE REPLY11AA05 BFRKD 18TYPE,SIDE,DECORATIVE DECORATIVE SIDE TYPE INDICATES THE TYPE OF DECORATIVE SIDE PROVIDED. SELECT REPLY CODE 10AA62 BFRLD /D/ 07POCKET POCKET AN INDICATION OF WHETHER OR NOT A POCKET IS INCLUDED. SELECT REPLY CODE 10AA49 BFRMD /D/ 09MATERIAL,POCKET POCKET MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE POCKET IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BFRNA 12QUANTITY,PARTITION PARTITION QUANTITY THE NUMBER OF PARTITION(S) PROVIDED. 1A MODE REPLY 0 BFRPA 12QUANTITY,PULL PULL QUANTITY THE NUMBER OF PULL(S) PROVIDED. 1A MODE REPLY 0 BFRQD /D/ 07FACILITIES,SHELF,OPEN COVER OPEN COVER SHELF FACILITIES AN INDICATION OF WHETHER OR NOT OPEN COVER SHELF FACILITIES ARE INCLUDED. SELECT REPLY CODE 10AA49 BFRRJ 04HEIGHT,COMPARTMENT COMPARTMENT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A COMPARTMENT,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BFRSJ /D/ 04DIAMETER,COMPARTMENT COMPARTMENT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COMPARTMENT,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BFRTD /D/ 07FEATURE,VULCANIZATION VULCANIZATION FEATURE AN INDICATION OF WHETHER OR NOT A VULCANIZATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BFRWG 19ARRANGEMENT,COMPARTMENT COMPARTMENT ARRANGEMENT AN INDICATION OF THE ARRANGEMENT OF THE COMPARTMENTS. FULL TEXT WRITE-IN 0 BFRXA /D/ 12QUANTITY ACCOMMODATED,ROCKET ROCKET QUANTITY ACCOMMODATED THE NUMBER OF ROCKET(S) THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 BFRYJ 04DEPTH,POCKET POCKET DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON A POCKET,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 BFRZJ /D/ 04LENGTH,ENGAGEMENT,THREAD THREAD ENGAGEMENT LENGTH THE NORMAL LENGTH OF ENGAGEMENT BETWEEN EXTERNAL AND INTERNAL TAPER THREADS. 1D AND 1B MODE REPLY11AA05 BFSBD /D/ 08LOCATION,FEATURE,ATTACHING,HAND GRENADE HAND GRENADE ATTACHING FEATURE LOCATION INDICATES THE LOCATION OF THE HAND GRENADE ATTACHING FEATURE ON THE ITEM. SELECT REPLY CODE 10AJ91 BFSCD /D/ 08LOCATION,FEATURE,LOOP ATTACHING LOOP ATTACHING FEATURE LOCATION INDICATES THE LOCATION OF THE LOOP ATTACHING FEATURE ON THE ITEM. SELECT REPLY CODE 10AJ91 BFSDD /D/ 09MATERIAL,REINFORCEMENT REINFORCEMENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE REINFORCEMENT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BFSFD 14SHAPE,REINFORCEMENT REINFORCEMENT SHAPE THE PHYSICAL CONFIGURATION OF THE REINFORCEMENT. SELECT REPLY CODE 10AD07 BFSGD /D/ 18TYPE,FILTER,DISTURBANCE SUPPRESSION DISTURBANCE SUPPRESSION FILTER TYPE INDICATES THE TYPE OF DISTURBANCE SUPPRESSION FILTERS PROVIDED TO PROTECT AN ITEM FROM OUTSIDE ELECTRICAL FREQUENCY INTERFERENCE. SELECT REPLY CODE 10AH81 BFSHD /D/ 02DESIGN,GEAR,FIRST FIRST GEAR DESIGN THE DESIGN OF THE GEAR. SELECT REPLY CODE 10AL23 BFSJD /D/ 02DESIGN,GEAR,SECOND SECOND GEAR DESIGN THE DESIGN OF THE GEAR. SELECT REPLY CODE 10AL23 BFSKD /D/ 02DESIGN,GEAR,THIRD THIRD GEAR DESIGN THE DESIGN OF THE GEAR. SELECT REPLY CODE 10AL23 BFSLD /D/ 02DESIGN,GEAR,FOURTH FOURTH GEAR DESIGN THE DESIGN OF THE GEAR. SELECT REPLY CODE 10AL23 BFSMJ /D/ 04DIAMETER,OUTSIDE,FIRST GEAR FIRST GEAR OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GEAR,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BFSNJ /D/ 04DIAMETER,OUTSIDE,SECOND GEAR SECOND GEAR OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GEAR,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BFSPJ /D/ 04DIAMETER,OUTSIDE,THIRD GEAR THIRD GEAR OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GEAR,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BFSQJ /D/ 04DIAMETER,OUTSIDE,FOURTH GEAR FOURTH GEAR OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GEAR,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BFSRJ /D/ 04DIAMETER,PITCH,FIRST GEAR FIRST GEAR PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF THE GEAR. 2D AND 1B MODE REPLY21AA051AC20 BFSSJ /D/ 04DIAMETER,PITCH,SECOND GEAR SECOND GEAR PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF THE GEAR. 2D AND 1B MODE REPLY21AA051AC20 BFSTJ /D/ 04DIAMETER,PITCH,THIRD GEAR THIRD GEAR PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF THE GEAR. 2D AND 1B MODE REPLY21AA051AC20 BFSWJ /D/ 04DIAMETER,PITCH,FOURTH GEAR FOURTH GEAR PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF THE GEAR. 2D AND 1B MODE REPLY21AA051AC20 BFSXJ /D/ 04WIDTH OF FACE,GEAR,FIRST FIRST GEAR WIDTH OF FACE A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE GEAR FACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BFSYJ /D/ 04WIDTH OF FACE,GEAR,SECOND SECOND GEAR WIDTH OF FACE A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE GEAR FACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BFSZJ /D/ 04WIDTH OF FACE,GEAR,THIRD THIRD GEAR WIDTH OF FACE A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE GEAR FACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BFTBJ /D/ 04WIDTH OF FACE,GEAR,FOURTH FOURTH GEAR WIDTH OF FACE A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE GEAR FACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BFTCJ /D/A04ANGLE,PRESSURE,FIRST GEAR FIRST GEAR PRESSURE ANGLE A MEASUREMENT OF THE PRESSURE ANGLE OF THE GEAR. 1D AND 1A MODE REPLY13AJ40 BFTDJ /D/A04ANGLE,PRESSURE,SECOND GEAR SECOND GEAR PRESSURE ANGLE A MEASUREMENT OF THE PRESSURE ANGLE OF THE GEAR. 1D AND 1A MODE REPLY13AJ40 BFTFJ /D/A04ANGLE,PRESSURE,THIRD GEAR THIRD GEAR PRESSURE ANGLE A MEASUREMENT OF THE PRESSURE ANGLE OF THE GEAR. 1D AND 1A MODE REPLY13AJ40 BFTGJ /D/A04ANGLE,PRESSURE,FOURTH GEAR FOURTH GEAR PRESSURE ANGLE A MEASUREMENT OF THE PRESSURE ANGLE OF THE GEAR. 1D AND 1A MODE REPLY13AJ40 BFTHD /D/ 05DIRECTION,TOOTH,FIRST GEAR FIRST GEAR TOOTH DIRECTION THE DIRECTION IN WHICH THE TEETH CURVE AWAY FROM THE AXIS WHEN VIEWED PARALLEL TO THE GEAR AXIS. SELECT REPLY CODE 10AA38 BFTJD /D/ 05DIRECTION,TOOTH,SECOND GEAR SECOND GEAR TOOTH DIRECTION THE DIRECTION IN WHICH THE TEETH CURVE AWAY FROM THE AXIS WHEN VIEWED PARALLEL TO THE GEAR AXIS. SELECT REPLY CODE 10AA38 BFTKD /D/ 05DIRECTION,TOOTH,THIRD GEAR THIRD GEAR TOOTH DIRECTION THE DIRECTION IN WHICH THE TEETH CURVE AWAY FROM THE AXIS WHEN VIEWED PARALLEL TO THE GEAR AXIS. SELECT REPLY CODE 10AA38 BFTLD /D/ 05DIRECTION,TOOTH,FOURTH GEAR FOURTH GEAR TOOTH DIRECTION THE DIRECTION IN WHICH THE TEETH CURVE AWAY FROM THE AXIS WHEN VIEWED PARALLEL TO THE GEAR AXIS. SELECT REPLY CODE 10AA38 BFTMA /D/ 12QUANTITY,TEETH,FIRST GEAR FIRST GEAR TEETH QUANTITY THE NUMBER OF TEETH ON THE ITEM. 1A MODE REPLY 0 BFTNA /D/ 12QUANTITY,TEETH,SECOND GEAR SECOND GEAR TEETH QUANTITY THE NUMBER OF TEETH ON THE ITEM. 1A MODE REPLY 0 BFTPA /D/ 12QUANTITY,TEETH,THIRD GEAR THIRD GEAR TEETH QUANTITY THE NUMBER OF TEETH ON THE ITEM. 1A MODE REPLY 0 BFTQA /D/ 12QUANTITY,TEETH,FOURTH GEAR FOURTH GEAR TEETH QUANTITY THE NUMBER OF TEETH ON THE ITEM. 1A MODE REPLY 0 BFTRJ /D/A04ANGLE,PITCH,FIRST GEAR FIRST GEAR PITCH ANGLE A MEASUREMENT OF THE PITCH ANGLE OF THE GEAR. 1D AND 1A MODE REPLY13AJ40 BFTSJ /D/A04ANGLE,PITCH,SECOND GEAR SECOND GEAR PITCH ANGLE A MEASUREMENT OF THE PITCH ANGLE OF THE GEAR. 1D AND 1A MODE REPLY13AJ40 BFTTJ /D/A04ANGLE,PITCH,THIRD GEAR THIRD GEAR PITCH ANGLE A MEAUSREMENT OF THE PITCH ANGLE OF THE GEAR. 1D AND 1A MODE REPLY13AJ40 BFTWJ /D/A04ANGLE,PITCH,FOURTH GEAR FOURTH GEAR PITCH ANGLE A MEASUREMENT OF THE PITCH ANGLE OF THE GEAR. 1D AND 1A MODE REPLY13AJ40 BFTXD /D/ 19POSITION,GEAR,FIRST BEVEL FIRST BEVEL GEAR POSITION AN INDICATION OF THE DIRECTION THE TEETH OF THE BEVEL GEAR ARE FACING WITH RESPECT TO THE GEAR CLUSTER. SELECT REPLY CODE 10AJ91 BFTYD /D/ 19POSITION,GEAR,SECOND BEVEL SECOND BEVEL GEAR POSITION AN INDICATION OF THE DIRECTION THE TEETH OF THE BEVEL GEAR ARE FACING WITH RESPECT TO THE GEAR CLUSTER. SELECT REPLY CODE 10AJ91 BFTZD /D/ 19POSITION,GEAR,THIRD BEVEL THIRD BEVEL GEAR POSITION AN INDICATION OF THE DIRECTION THE TEETH OF THE BEVEL GEAR ARE FACING WITH RESPECT TO THE GEAR CLUSTER. SELECT REPLY CODE 10AJ91 BFWBD /D/ 19POSITION,GEAR,FOURTH BEVEL FOURTH BEVEL GEAR POSITION AN INDICATION OF THE DIRECTION THE TEETH OF THE BEVEL GEAR ARE FACING WITH RESPECT TO THE GEAR CLUSTER. SELECT REPLY CODE 10AJ91 BFWCJ /D/A04ANGLE,HELIX,TOOTH,FIRST GEAR FIRST GEAR TOOTH HELIX ANGLE THE ANGULAR AMOUNT THE TEETH OF A RACK OR GEAR ARE INCLINED. 1D AND 1A MODE REPLY13AJ40 BFWDJ /D/A04ANGLE,HELIX,TOOTH,SECOND GEAR SECOND GEAR TOOTH HELIX ANGLE THE ANGULAR AMOUNT THE TEETH OF A RACK OR GEAR ARE INCLINED. 1D AND 1A MODE REPLY13AJ40 BFWFJ /D/A04ANGLE,HELIX,TOOTH,THIRD GEAR THIRD GEAR TOOTH HELIX ANGLE THE ANGULAR AMOUNT THE TEETH OF A RACK OR GEAR ARE INCLINED. 1D AND 1A MODE REPLY13AJ40 BFWGJ /D/A04ANGLE,HELIX,TOOTH,FOURTH GEAR FOURTH GEAR TOOTH HELIX ANGLE THE ANGULAR AMOUNT THE TEETH OF A RACK OR GEAR ARE INCLINED. 1D AND 1A MODE REPLY13AJ40 BFWHJ /D/ 04RADIUS OF THROAT,GEAR,FIRST FIRST GEAR RADIUS OF THROAT THE MEASUREMENT OF THE CONCAVE CURVATURE ACROSS THE FACE OF A WORM GEAR OR WORM WHEEL. 2D AND 1B MODE REPLY21AA051AC20 BFWJJ /D/ 04RADIUS OF THROAT,GEAR,SECOND SECOND GEAR RADIUS OF THROAT THE MEASUREMENT OF THE CONCAVE CURVATURE ACROSS THE FACE OF A WORM GEAR OR WORM WHEEL. 2D AND 1B MODE REPLY21AA051AC20 BFWKJ /D/ 04RADIUS OF THROAT,GEAR,THIRD THIRD GEAR RADIUS OF THROAT THE MEASUREMENT OF THE CONCAVE CURVATURE ACROSS THE FACE OF A WORM GEAR OR WORM WHEEL. 2D AND 1B MODE REPLY21AA051AC20 BFWLJ /D/ 04RADIUS OF THROAT,GEAR,FOURTH FOURTH GEAR RADIUS OF THROAT THE MEASUREMENT OF THE CONCAVE CURVATURE ACROSS THE FACE OF A WORM GEAR OR WORM WHEEL. 2D AND 1B MODE REPLY21AA051AC20 BFWMJ /D/ 04DIAMETER,THROAT,FIRST GEAR FIRST GEAR THROAT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GEAR THROAT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BFWNJ /D/ 04DIAMETER,THROAT,SECOND GEAR SECOND GEAR THROAT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GEAR THROAT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BFWPJ /D/ 04DIAMETER,THROAT,THIRD GEAR THIRD GEAR THROAT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GEAR THROAT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BFWQJ /D/ 04DIAMETER,THROAT,FOURTH GEAR FOURTH GEAR THROAT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GEAR THROAT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BFWRA /D/ 13THREAD QUANTITY,GEAR,FIRST FIRST GEAR THREAD QUANTITY THE TOTAL NUMBER OF THREAD FORMS THAT PROGRESS HELICALLY AROUND THE GEAR AXIS. 1A MODE REPLY 0 BFWSA /D/ 13THREAD QUANTITY,GEAR,SECOND SECOND GEAR THREAD QUANTITY THE TOTAL NUMBER OF THREAD FORMS THAT PROGRESS HELICALLY AROUND THE GEAR AXIS. 1A MODE REPLY 0 BFWTA /D/ 13THREAD QUANTITY,GEAR,THIRD THIRD GEAR THREAD QUANTITY THE TOTAL NUMBER OF THREAD FORMS THAT PROGRESS HELICALLY AROUND THE GEAR AXIS. 1A MODE REPLY 0 BFWWA /D/ 13THREAD QUANTITY,GEAR,FOURTH FOURTH GEAR THREAD QUANTITY THE TOTAL NUMBER OF THREAD FORMS THAT PROGRESS HELICALLY AROUND THE GEAR AXIS. 1A MODE REPLY 0 BFWXJ /D/A04ANGLE,LEAD,FIRST GEAR FIRST GEAR LEAD ANGLE A MEASUREMENT OF THE LEAD ANGLE OF THE GEAR. 1D AND 1A MODE REPLY13AJ40 BFWYJ /D/A04ANGLE,LEAD,SECOND GEAR SECOND GEAR LEAD ANGLE A MEASUREMENT OF THE LEAD ANGLE OF THE GEAR. 1D AND 1A MODE REPLY13AJ40 BFWZJ /D/A04ANGLE,LEAD,THIRD GEAR THIRD GEAR LEAD ANGLE A MEASUREMENT OF THE LEAD ANGLE OF THE GEAR. 1D AND 1A MODE REPLY13AJ40 BFXBJ /D/A04ANGLE,LEAD,FOURTH GEAR FOURTH GEAR LEAD ANGLE A MEASUREMENT OF THE LEAD ANGLE OF THE GEAR. 1D AND 1A MODE REPLY13AJ40 BFXCJ /D/ 13THREAD LEAD,GEAR,FIRST FIRST GEAR THREAD LEAD THE DISTANCE THAT ANY SINGLE THREAD WILL ADVANCE AXIALLY IN ONE COMPLETE REVOLUTION. 2D AND 1B MODE REPLY21AA051AC20 BFXDJ /D/ 13THREAD LEAD,GEAR,SECOND SECOND GEAR THREAD LEAD THE DISTANCE THAT ANY SINGLE THREAD WILL ADVANCE AXIALLY IN ONE COMPLETE REVOLUTION. 2D AND 1B MODE REPLY21AA051AC20 BFXFJ /D/ 13THREAD LEAD,GEAR,THIRD THIRD GEAR THREAD LEAD THE DISTANCE THAT ANY SINGLE THREAD WILL ADVANCE AXIALLY IN ONE COMPLETE REVOLUTION. 2D AND 1B MODE REPLY21AA051AC20 BFXGJ /D/ 13THREAD LEAD,GEAR,FOURTH FOURTH GEAR THREAD LEAD THE DISTANCE THAT ANY SINGLE THREAD WILL ADVANCE AXIALLY IN ONE COMPLETE REVOLUTION. 2D AND 1B MODE REPLY21AA051AC20 BFXHD /D/ 13THREAD DIRECTION,GEAR,FIRST FIRST GEAR THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 BFXJD /D/ 13THREAD DIRECTION,GEAR,SECOND SECOND GEAR THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 BFXKD /D/ 13THREAD DIRECTION,GEAR,THIRD THIRD GEAR THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 BFXLD /D/ 13THREAD DIRECTION,GEAR,FOURTH FOURTH GEAR THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 BFXMJ /D/ 10PITCH IN INCHES,GEAR,FIRST FIRST GEAR PITCH IN INCHES THE DISTANCE BETWEEN IDENTICAL,EQUALLY SPACED SURFACES OF TWO ADJOINING TEETH OR THREADS ON A GEAR,RACK OR WORM,MEASURED ALONG THE PITCH CIRCLE OR PITCH LINE. 1D AND 1B MODE REPLY12AL87 BFXNJ /D/ 10PITCH IN INCHES,GEAR,SECOND SECOND GEAR PITCH IN INCHES THE DISTANCE BETWEEN IDENTICAL,EQUALLY SPACED SURFACES OF TWO ADJOINING TEETH OR THREADS ON A GEAR,RACK OR WORM,MEASURED ALONG THE PITCH CIRCLE OR PITCH LINE. 1D AND 1B MODE REPLY12AL87 BFXPJ /D/ 10PITCH IN INCHES,GEAR,THIRD THIRD GEAR PITCH IN INCHES THE DISTANCE BETWEEN IDENTICAL,EQUALLY SPACED SURFACES OF TWO ADJOINING TEETH OR THREADS ON A GEAR,RACK OR WORM,MEASURED ALONG THE PITCH CIRCLE OR PITCH LINE. 1D AND 1B MODE REPLY12AL87 BFXQJ /D/ 10PITCH IN INCHES,GEAR,FOURTH FOURTH GEAR PITCH IN INCHES THE DISTANCE BETWEEN IDENTICAL,EQUALLY SPACED SURFACES OF TWO ADJOINING TEETH OR THREADS ON A GEAR,RACK OR WORM,MEASURED ALONG THE PITCH CIRCLE OR PITCH LINE. 1D AND 1B MODE REPLY12AL87 BFXRJ 04DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO THE HEIGHT,CENTER TO CENTER,FIRST FIRST CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO THE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BFXSJ 04DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO THE WIDTH,CENTER TO CENTER,FIRST FIRST CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO THE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFXTJ 04DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO THE HEIGHT,CENTER TO CENTER,SECOND SECOND CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO THE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BFXWJ 04DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO THE WIDTH,CENTER TO CENTER,SECOND SECOND CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO THE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFXXJ 04DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO THE HEIGHT,CENTER TO CENTER,THIRD THIRD CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BFXYJ 04DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO THE WIDTH,CENTER TO CENTER,THIRD THIRD CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BFXZL /D/ 16STYLE,ENTRANCE ENTRANCE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ENTRANCE. 1L MODE REPLY 0 BFYBJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,HUB HUB THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED HUB. PLEASE USE MRC THDS IN PLACE OF THIS CANCELED MRC. 1D AND 1A MODE REPLY12AH06 BFYCB 10CURRENT RATING IN AMPS,MAXIMUM,MAIN LINE MAIN LINE MAXIMUM CURRENT RATING IN AMPS THE MAXIMUM CURRENT RATING OF THE MAIN LINE,EXPRESSED IN AMPERES. 1B MODE REPLY 0 BFYDB 10VOLTAGE RATING IN VOLTS,AC,MAXIMUM,MAIN LINE MAIN LINE MAXIMUM AC VOLTAGE RATING IN VOLTS THE MAXIMUM ALTERNATING CURRENT VOLTAGE RATING OF THE MAIN LINE,EXPRESSED IN VOLTS. 1B MODE REPLY 0 BFYFD /D/ 09MATERIAL,COATING,BACK BACK COATING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BACK COATING IS FABRICATED. SELECT REPLY CODE 10AD09 BFYGD /D/ 09MATERIAL,CUSHION,FUSED FUSED CUSHION MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FUSED CUSHION IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BFYHJ 04THICKNESS,CUSHION CUSHION THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE CUSHION,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BFYJJ 10WEIGHT,MAXIMUM MAXIMUM WEIGHT THE MAXIMUM RELATIVE MEASURE OF THE MASS OF THE ITEM WITH RESPECT TO ITS DENSITY. 1D AND 1B MODE REPLY12AG67 BFYKD /D/ 07FEATURE,USAGE,DESK TOP DESK TOP USAGE FEATURE AN INDICATION OF WHETHER OR NOT A DESK TOP USAGE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BFYLG /D/ 19CONTROLLER,DESIGNATION,COLOR/SHADE/PATTERN COLOR/SHADE/PATTERN DESIGNATION CONTROLLER THE NAME OF THE GOVERNMENT AGENCY,COMMERCIAL ORGANIZATION,OR MANUFACTURER CONTROLLING THE COLOR,SHADE,OR PATTERN DESIGNATION. FULL TEXT WRITE-IN 0 BFYMD /D/ 07FEATURE,USAGE,WALL SURFACE WALL SURFACE USAGE FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE FOR WALL SURFACE USE IS INCLUDED. SELECT REPLY CODE 10AA49 BFYNG /D/ 19CONTROLLER,DESIGNATION,COLOR/SHADE COLOR/SHADE DESIGNATION CONTROLLER THE NAME OF THE GOVERNMENT AGENCY, COMMERCIAL ORGANIZATION,OR MANUFACTURER CONTROLLING THE COLOR OR SHADE DESIGNATION. FULL TEXT WRITE-IN 0 BFYPD /D/ 09MATERIAL,IMPREGNATION,BASE BASE IMPREGNATION MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE WITH WHICH THE BASE IS IMPREGNATED. SELECT REPLY CODE 10AD09 BFYQG /D/ 10WEIGHT WEIGHT THE RELATIVE MEASURE OF THE MASS OF THE ITEM WITH RESPECT TO ITS DENSITY. FULL TEXT WRITE-IN 0 BFYRJ 04DISTANCE FROM BORE CENTERLINE TO BASE BOTTOM DISTANCE FROM BORE CENTERLINE TO BASE BOTTOM THE DISTANCE FROM THE BORE CENTERLINE TO THE BASE BOTTOM. 2D AND 1B MODE REPLY21AA051AC20 BFYSD /D/ 18TYPE FOR WHICH DRILLED,ATTACHMENT ATTACHMENT TYPE FOR WHICH DRILLED INDICATES THE TYPE OF ATTACHMENT FOR WHICH THE ITEM IS DRILLED. SELECT REPLY CODE 10AM39 BFYTG 08LOCATION,HOLE HOLE LOCATION INDICATES THE LOCATION OF THE HOLE ON THE ITEM. FULL TEXT WRITE-IN 0 BFYWJ /D/ 10HARDNESS RATING,MATERIAL,ATTACHMENT,END END ATTACHMENT MATERIAL HARDNESS RATING A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF THE MATERIAL OF THE END ATTACHMENT WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE. 2D AND 1B MODE REPLY22AC261AC20 BFYXD 07PROVISION,THREAD,BALL END CONNECTION BALL END CONNECTION THREAD PROVISION AN INDICATION OF WHETHER OR NOT THE BALL END CONNECTION IS THREADED. SELECT REPLY CODE 10AE00 BFYYD 13THREAD LOCATION,END,BALL BALL END THREAD LOCATION INDICATES THE PORTION(S) OF AN ITEM ON WHICH THE THREAD(S) IS LOCATED. SELECT REPLY CODE 10AJ91 BFYZA /D/ 13THREAD SIZE,END,BALL BALL END THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE BALL END. 1A MODE REPLY 0 BFZBD /D/ 13THREAD SERIES DESIGNATOR,END,BALL BALL END THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR THE DIAMETER OF A BALL END. SELECT REPLY CODE 10AH06 BFZCD 13THREAD DIRECTION,END,BALL BALL END THREAD DIRECTION THE DIRECTION OF THE BALL END THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 BFZDD /D/ 18TYPE,END,UNTHREADED BALL UNTHREADED BALL END TYPE INDICATES THE TYPE OF UNTHREADED BALL END PROVIDED. SELECT REPLY CODE 10AA43 BFZFJ /D/ 04DIAMETER,OUTSIDE,UNTHREADED BALL END UNTHREADED BALL END OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED BALL END,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BFZGJ /D/ 04DIAMETER,INSIDE,UNTHREADED BALL END UNTHREADED BALL END INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED BALL END,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BFZHJ /D/ 04DEPTH,BALL END,UNTHREADED UNTHREADED BALL END DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON AN UNTHREADED BALL END,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BFZJD 07PROVISION,THREAD,SOCKET END CONNECTION SOCKET END CONNECTION THREAD PROVISION AN INDICATION OF WHETHER OR NOT THE SOCKET END CONNECTION IS THREADED. SELECT REPLY CODE 10AE00 BFZKD 13THREAD LOCATION,END,SOCKET SOCKET END THREAD LOCATION INDICATES THE PORTION(S) OF AN ITEM ON WHICH THE THREAD(S) IS LOCATED. SELECT REPLY CODE 10AJ91 BFZLA /D/ 13THREAD SIZE,END,SOCKET SOCKET END THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE SOCKET END. 1A MODE REPLY 0 BFZMJ /D/ 13THREAD LENGTH,END,BALL BALL END THREAD LENGTH A MEASUREMENT OF THE EXTENT OF BALL END THREADS ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS. 2D AND 1B MODE REPLY21AA051AC20 BFZND 13THREAD SERIES DESIGNATOR,END,SOCKET SOCKET END THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR THE DIAMETER OF A SOCKET END. SELECT REPLY CODE 10AH06 BFZPD 13THREAD DIRECTION,END,SOCKET SOCKET END THREAD DIRECTION THE DIRECTION OF THE SOCKET END THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 BFZQD /D/ 18TYPE,END,UNTHREADED SOCKET UNTHREADED SOCKET END TYPE INDICATES THE TYPE OF UNTHREADED SOCKET END PROVIDED. SELECT REPLY CODE 10AA43 BFZRJ /D/ 04DIAMETER,OUTSIDE,UNTHREADED SOCKET END UNTHREADED SOCKET END OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED SOCKET END,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BFZSJ /D/ 04DIAMETER,INSIDE,UNTHREADED SOCKET END UNTHREADED SOCKET END INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED SOCKET END,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BFZTJ /D/ 04DEPTH,SOCKET END,UNTHREADED UNTHREADED SOCKET END DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON AN UNTHREADED SOCKET END,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BFZWJ T10RANGE,INDICATOR,SPEED SPEED INDICATOR RANGE AN INDICATION OF THE RANGE OF THE SPEED INDICATOR. 1D AND 1F MODE REPLY11AA34 BFZXG /D/ 10UNIT,GRADUATION,MAJOR MAJOR GRADUATION UNIT THE INCREMENT OF THE MAJOR GRADUATION/S/ ON THE ITEM. FULL TEXT WRITE-IN 0 BFZYJ T10RANGE,TOTAL,ODOMETER ODOMETER TOTAL RANGE AN INDICATION OF THE TOTAL RANGE OF THE ODOMETER. 1D AND 1F MODE REPLY11AA34 BFZZD /D/ 07ODOMETER,TRIP TRIP ODOMETER AN INDICATION OF WHETHER OR NOT A TRIP ODOMETER IS PROVIDED. SELECT REPLY CODE 10AB22 BGBBJ T10RANGE,ODOMETER,TRIP TRIP ODOMETER RANGE AN INDICATION OF THE RANGE OF THE TRIP ODOMETER. 1D AND 1F MODE REPLY11AA34 BGBCD 02DESIGN,OPENING,SHAFT SHAFT OPENING DESIGN THE DESIGN OF THE SHAFT OPENING ON THE ITEM. SELECT REPLY CODE 10AK54 BGBDJ 10SIZE SIZE DESIGNATES THE SIZE OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BGDFJ /D/ 04DISTANCE,SHAFT CENTER TO MOUNTING SURFACE SHAFT CENTER TO MOUNTING SURFACE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 BGDGJ /D/ 04LENGTH OF SHAFT FROM HOUSING LENGTH OF SHAFT FROM HOUSING NONE. 2D AND 1B MODE REPLY21AA051AC20 BGDHA 12QUANTITY,PEDESTAL PEDESTAL QUANTITY THE NUMBER OF PEDESTAL(S) PROVIDED. 1A MODE REPLY 0 BGDJD 14SHAPE,CROSS-SECTIONAL,LEG LEG CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE LEG WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 BGDKD /D/ 07DOOR,SLIDING SLIDING DOOR AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A SLIDING DOOR(S). SELECT REPLY CODE 10AB22 BGDLA 12QUANTITY,UNIT,COOLING COOLING UNIT QUANTITY THE NUMBER OF COOLING UNIT(S). 1A MODE REPLY 0 BGDMH /D/ 18TYPE AND LOCATION,ADJUSTMENT ADJUSTMENT TYPE AND LOCATION INDICATES THE TYPE OF ADJUSTMENT,AND ITS LOCATION. 2D MODE REPLY 23AN063AJ91 BGDND 02DESIGN,PERIOD PERIOD DESIGN THE DESIGN OF AN ITEM DISTINGUISHED BY THE TIME PERIOD IN WHICH THAT PARTICULAR DESIGN CAME INTO USE. SELECT REPLY CODE 10AN07 BGDPH 02DESIGN,BACK AND UPHOLSTERY BACK AND UPHOLSTERY DESIGN THE DESIGN OF THE BACK AND UPHOLSTERY OF THE ITEM. 2D MODE REPLY 22AH793AN09 BGDSJ /D/A18TYPE/LOCATION AND QUANTITY,CUSHION CUSHION TYPE/LOCATION AND QUANTITY INDICATES THE TYPE,LOCATION,AND NUMBER OF CUSHION(S) INHERENT IN THE ITEM. 2D AND 1A MODE REPLY23AJ911AF62 BGDTJ A18TYPE/LOCATION AND QUANTITY,SHELF SHELF TYPE/LOCATION AND QUANTITY INDICATES THE TYPE,LOCATION,AND NUMBER OF SHELVES INHERENT IN THE ITEM. 2D AND 1A MODE REPLY23AJ912AD27 BGDWJ A08LOCATION AND QUANTITY,DRAWER DRAWER LOCATION AND QUANTITY INDICATES THE LOCATION AND NUMBER OF DRAWERS IN THE ITEM. 1D AND 1A MODE REPLY13AJ91 BGDXJ A08LOCATION AND QUANTITY,COMPARTMENT COMPARTMENT LOCATION AND QUANTITY INDICATES THE LOCATION AND NUMBER OF COMPARTMENTS BUILT INTO THE ITEM. 1D AND 1A MODE REPLY13AJ91 BGDYJ A18TYPE AND QUANTITY,DOOR DOOR TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF DOORS FURNISHED WITH THE ITEM. 1D AND 1A MODE REPLY12AD27 BGDZJ 04LENGTH,OVERALL,BEDSPRING BEDSPRING OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BGFBJ 04HEIGHT ABOVE FLOOR,BEDSPRING,OVERALL OVERALL BEDSPRING HEIGHT ABOVE FLOOR NONE. 2D AND 1B MODE REPLY21AA051AC20 BGFCJ 04HEIGHT,OVERALL,HEADBOARD HEADBOARD OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BGFDJ 04WIDTH,OVERALL,HEADBOARD HEADBOARD OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BGFFJ 04HEIGHT,OVERALL,FOOTBOARD FOOTBOARD OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BGFGJ 04WIDTH,OVERALL,FOOTBOARD FOOTBOARD OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BGFHJ 04DEPTH,SEAT SEAT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BGFJJ 04WIDTH,SEAT SEAT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A SEAT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BGFKJ 04HEIGHT FROM FLOOR,TOP,SEAT SEAT TOP HEIGHT FROM FLOOR THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE FLOOR TO TOP OF THE SEAT. 2D AND 1B MODE REPLY21AA051AC20 BGFLJ 04HEIGHT,BACK BACK HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BGFMJ 04WIDTH,BACK BACK WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BACK,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BGFNJ /D/ 04LENGTH,ARM,DESK TOP/TABLET DESK TOP/TABLET ARM LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BGFPJ /D/ 04WIDTH,ARM,DESK TOP/TABLET DESK TOP/TABLET ARM WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BGFQJ 04LENGTH,SPACE,SEATING SEATING SPACE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BGFRJ 04LENGTH,SPACE,SLEEPING SLEEPING SPACE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BGFSJ 04LENGTH,MIRROR MIRROR LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A MIRROR,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BGFTJ 04WIDTH,MIRROR MIRROR WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A MIRROR,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BGFWJ 04LENGTH,OVERALL,TOP TOP OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE TOP. 2D AND 1B MODE REPLY21AA051AC20 BGFXJ 04WIDTH,OVERALL,TOP TOP OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TOP,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BGFYJ 04DIAMETER,OVERALL,TOP TOP OVERALL DIAMETER THE OVERALL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TOP,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BGFZJ 04LENGTH W/LEAVES CLOSED,OVERALL OVERALL LENGTH W/LEAVES CLOSED NONE. 2D AND 1B MODE REPLY21AA051AC20 BGGBJ 04LENGTH W/LEAVES EXTENDED,OVERALL OVERALL LENGTH W/LEAVES EXTENDED NONE. 2D AND 1B MODE REPLY21AA051AC20 BGGCD /D/ 07CATALYST,SEPARATE SEPARATE CATALYST AN INDICATION OF WHETHER OR NOT A SEPARATE CATALYST IS INCLUDED. SELECT REPLY CODE 10AA49 BGGDD /D/ 08LOCATION,FEATURE,STEEL LEAF RETAINING STEEL LEAF RETAINING FEATURE LOCATION INDICATES THE LOCATION OF THE STEEL LEAF RETAINING FEATURE ON THE ITEM. SELECT REPLY CODE 10AJ91 BGGFD /D/ 07FLAP FLAP AN INDICATION OF WHETHER OR NOT A FLAP IS INCLUDED. SELECT REPLY CODE 10AA49 BGGGD 11METHOD,ATTACHMENT,COMPONENT COMPONENT ATTACHMENT METHOD THE MEANS USED TO ATTACH THE COMPONENT. SELECT REPLY CODE 10AB47 BGGHA 12QUANTITY,STRAP STRAP QUANTITY THE NUMBER OF STRAPS PROVIDED. 1A MODE REPLY 0 BGGJJ A04SIZE,GAGE,SHEET METAL SHEET METAL GAGE SIZE DESIGNATES THE SHEET METAL GAGE SIZE. 1D AND 1A MODE REPLY12AH09 BGGKD 18TYPE,HOOP,ROLLING ROLLING HOOP TYPE INDICATES THE TYPE OF ROLLING HOOP(S) PROVIDED. SELECT REPLY CODE 10AK54 BGGLA 12QUANTITY,HANDLE,AUXILIARY AUXILIARY HANDLE QUANTITY THE NUMBER OF AUXILIARY HANDLES PROVIDED. 1A MODE REPLY 0 BGGMD 08LOCATION,HANDLE,AUXILIARY AUXILIARY HANDLE LOCATION INDICATES THE LOCATION OF THE AUXILIARY HANDLE(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 BGGND /D/ 09MATERIAL,HARDWARE HARDWARE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HARDWARE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BGGPD 08LOCATION,FACILITY,HANDLING HANDLING FACILITY LOCATION INDICATES THE LOCATION OF THE HANDLING FACILITY. SELECT REPLY CODE 10AJ91 BGGQD 08LOCATION,BUNG BUNG LOCATION INDICATES THE LOCATION OF THE BUNG. SELECT REPLY CODE 10AJ91 BGGRD 08LOCATION,VENT VENT LOCATION INDICATES THE LOCATION OF THE VENT. SELECT REPLY CODE 10AJ91 BGGSD 18TYPE,INDICATOR,HUMIDITY HUMIDITY INDICATOR TYPE INDICATES THE TYPE OF HUMIDITY INDICATOR PROVIDED. SELECT REPLY CODE 10AJ12 BGGTD 08LOCATION,INDICATOR INDICATOR LOCATION INDICATES THE LOCATION OF THE INDICATOR. SELECT REPLY CODE 10AJ91 BGGWD /D/ 07SPOUT SPOUT AN INDICATION OF WHETHER OR NOT A SPOUT IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BGGXD /D/ 07AGITATOR,INTERNAL INTERNAL AGITATOR AN INDICATION OF WHETHER OR NOT AN INTERNAL AGITATOR IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BGGYD 18TYPE,CURRENT,SWITCHBOARD SIDE SWITCHBOARD SIDE CURRENT TYPE INDICATES THE TYPE OF SWITCHBOARD SIDE CURRENT,WHETHER ALTERNATING OR DIRECT. SELECT REPLY CODE 10AB62 BGGZD 19FEATURE,REUSABILITY REUSABILITY FEATURE THE DESIGN CAPABILITY WHICH ALLOWS AN ITEM TO BE CLEANED AND REUSED. SELECT REPLY CODE 10AJ61 BGHBJ 10FREQUENCY RATING,SIGNAL,SWITCHBOARD,RECEIVED RECEIVED SWITCHBOARD SIGNAL FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE SWITCHBOARD RECEIVED SIGNAL IS RATED. 2D AND 1B MODE REPLY21AC321AC20 BGHCJ 10FREQUENCY RATING,SIGNAL,SWITCHBOARD,TRANSMITTED TRANSMITTED SWITCHBOARD SIGNAL FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE SWITCHBOARD TRANSMITTED SIGNAL IS RATED. 2D AND 1B MODE REPLY21AC321AC20 BGHDJ 10VOLTAGE RATING,DC,RECEIVED SIGNAL RECEIVED SIGNAL DC VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,OF DIRECT CURRENT POTENTIAL FOR WHICH THE RECEIVED SIGNAL IS RATED. 2D AND 1B MODE REPLY21AB631AC20 BGHFJ 10VOLTAGE RATING,DC,TRANSMITTED SIGNAL TRANSMITTED SIGNAL DC VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,OF DIRECT CURRENT POTENTIAL FOR WHICH THE TRANSMITTED SIGNAL IS RATED. 2D AND 1B MODE REPLY21AB631AC20 BGHGJ 10FREQUENCY RATING,SIGNAL,LINE,TRANSMITTED TRANSMITTED LINE SIGNAL FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE TRANSMITTED LINE SIGNAL IS RATED. 2D AND 1B MODE REPLY21AC321AC20 BGHHJ 10FREQUENCY RATING,SIGNAL,RECEIVED LINE RECEIVED LINE SIGNAL FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE RECEIVED LINE SIGNAL IS RATED. 2D AND 1B MODE REPLY21AC321AC20 BGHJA 12QUANTITY,CIRCUIT,COMMUNICATION COMMUNICATION CIRCUIT QUANTITY THE NUMBER OF COMMUNICATION CIRCUITS PROVIDED. 1A MODE REPLY 0 BGHKA /D/ 12QUANTITY,TERMINAL,BATTERY BATTERY TERMINAL QUANTITY THE NUMBER OF BATTERY TERMINALS PROVIDING ELECTRICAL CONNECTION TO THE ITEM. 1A MODE REPLY 0 BGHLD /D/ 18TYPE,TERMINAL,BATTERY BATTERY TERMINAL TYPE INDICATES THE TYPE OF BATTERY TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO AN ITEM. SELECT REPLY CODE 10AA58 BGHMD /D/ 07CONNECTOR,CABLE,EXTERNAL,CASE CASE EXTERNAL CABLE CONNECTOR AN INDICATION OF WHETHER OR NOT A CASE EXTERNAL CABLE CONNECTOR/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 BGHNA /D/ 12QUANTITY,CONNECTOR,EXTERNAL CABLE EXTERNAL CABLE CONNECTOR QUANTITY THE NUMBER OF EXTERNAL CABLE CONNECTORS PROVIDED. 1A MODE REPLY 0 BGHPJ /D/ 04LENGTH,BATTERY BATTERY LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BATTERY,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BGHQJ /D/ 04DIAMETER,BATTERY BATTERY DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BATTERY,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BGHRJ /D/ 04WIDTH,BATTERY BATTERY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BATTERY,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BGHSJ /D/ 04HEIGHT,BATTERY BATTERY HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BATTERY,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BGHTJ /D/ 04DEPTH,BATTERY BATTERY DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE BATTERY,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BGHWD /D/ 18TYPE,CONNECTOR,CABLE CABLE CONNECTOR TYPE INDICATES THE TYPE OF CABLE CONNECTOR PROVIDED. SELECT REPLY CODE 10AJ57 BGHXA 12QUANTITY,CONTROL,OUTPUT OUTPUT CONTROL QUANTITY THE NUMBER OF OUTPUT CONTROL(S) PROVIDED. 1A MODE REPLY 0 BGHYD 18TYPE,CONTROL,OUTPUT OUTPUT CONTROL TYPE INDICATES THE TYPE OF OUTPUT CONTROL PROVIDED. SELECT REPLY CODE 10AL37 BGHZA /D/ 12QUANTITY,CONTROL,BATTERY ACTIVATION BATTERY ACTIVATION CONTROL QUANTITY THE NUMBER OF BATTERY ACTIVATION CONTROL(S) PROVIDED. 1A MODE REPLY 0 BGJBD /D/ 18TYPE,CONTROL,BATTERY ACTIVATION BATTERY ACTIVATION CONTROL TYPE INDICATES THE TYPE OF BATTERY ACTIVATION CONTROL(S) PROVIDED. SELECT REPLY CODE 10AL37 BGJCG /D/ 18TYPE,FACILITY,MOUNTING MOUNTING FACILITY TYPE INDICATES THE TYPE OF FACILITY(IES) PROVIDED,PERMITTING ATTACHMENT OF THE ITEM TO A SURFACE OR TO ANOTHER ITEM. FULL TEXT WRITE-IN 0 BGJDB 10VOLTAGE RATING IN VOLTS,DC,MAXIMUM,MAIN LINE MAIN LINE MAXIMUM DC VOLTAGE RATING IN VOLTS THE MAXIMUM DIRECT CURRENT VOLTAGE RATING OF THE MAIN LINE,EXPRESSED IN VOLTS. 1B MODE REPLY 0 BGJFJ /D/ 04DISTANCE BETWEEN THREADED MOUNTING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN THREADED MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 BGJGJ /D/ 04DISTANCE FROM END OF RACK TO CENTER OF FIRST THREADED MOUNTING HOLE DISTANCE FROM END OF RACK TO CENTER OF FIRST THREADED MOUNTING HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BGJHD 18TYPE FOR WHICH DESIGNED,CONNECTION,GROUND GROUND CONNECTION TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF GROUND CONNECTION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AG39 BGJJA 12QUANTITY,TERMINAL,GROUNDING FOOT GROUNDING FOOT TERMINAL QUANTITY THE NUMBER OF GROUNDING FOOT TERMINALS PROVIDED. 1A MODE REPLY 0 BGJKA 12QUANTITY,TERMINAL,GROUNDING LINK GROUNDING LINK TERMINAL QUANTITY THE NUMBER OF GROUNDING LINK TERMINALS PROVIDED. 1A MODE REPLY 0 BGJLJ A18TYPE AND QUANTITY,BREAKER,CIRCUIT CIRCUIT BREAKER TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF CIRCUIT BREAKERS PROVIDED. 1D AND 1A MODE REPLY12AC82 BGJMB 10CURRENT RATING IN AMPS,BREAKER,CIRCUIT CIRCUIT BREAKER CURRENT RATING IN AMPS THE MAXIMUM ELECTRICAL CURRENT WHICH THE CIRCUIT BREAKER WILL CARRY WITHOUT INTERRUPTING THE CIRCUIT,EXPRESSED IN AMPERES. 1B MODE REPLY 0 BGJNJ A18TYPE AND QUANTITY,SWITCH SWITCH TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF SWITCHES PROVIDED. 1D AND 1A MODE REPLY12AC82 BGJPJ A18TYPE AND QUANTITY ACCOMMODATED,FUSE FUSE TYPE AND QUANTITY ACCOMMODATED INDICATES THE TYPE AND NUMBER OF FUSES THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1A MODE REPLY12AC82 BGJQA 19IDENTIFICATION,BREAKER,CIRCUIT CIRCUIT BREAKER IDENTIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS IDENTIFICATION NUMBER OR SYMBOL USED TO IDENTIFY THE CIRCUIT BREAKER. 1A MODE REPLY 0 BGJRA 19CODE,MANUFACTURER,CIRCUIT BREAKER CIRCUIT BREAKER MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE CIRCUIT BREAKER. 1A MODE REPLY 0 BGJSA 19IDENTIFICATION,SWITCH SWITCH IDENTIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS IDENTIFICATION NUMBER OR SYMBOL USED TO IDENTIFY THE SWITCH. 1A MODE REPLY 0 BGJTA 19CODE,MANUFACTURER,SWITCH SWITCH MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE SWITCH. 1A MODE REPLY 0 BGJWA 19IDENTIFICATION,JACK JACK IDENTIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS IDENTIFICATION NUMBER OR SYMBOL USED TO IDENTIFY THE JACK. 1A MODE REPLY 0 BGJXA /D/ 19CODE,MANUFACTURER,JACK JACK MANUFACTURER CODE THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE JACK. 1A MODE REPLY 0 BGJYJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,BASE BASE THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED BASE. 1D AND 1A MODE REPLY12AH06 BGJZJ 04DIAMETER,INSIDE,BASE BASE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BGKBJ 04LENGTH,OVERALL,BASE BASE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BASE. 2D AND 1B MODE REPLY21AA051AC20 BGKCJ 04DIAMETER,INSIDE,OPENING OPENING INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO SURFACES OF A CIRCULAR OPENING,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BGKDJ 04LENGTH,HOLE,ACCOMMODATION ACCOMMODATION HOLE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BGKFJ 10YIELD,PACKAGE,UNIT UNIT PACKAGE YIELD THE YIELD PER PACKAGE UNIT WHEN MIXED AS RECOMMENDED. 1D AND 1B MODE REPLY12AG67 BGKGD 19USAGE,SEQUENTIAL SEQUENTIAL USAGE AN INDICATION OF WHICH STEP IN A PROCESS THE ITEM IS USED. SELECT REPLY CODE 10AG66 BGKHD 11METHOD,PROCESSING,MATERIAL MATERIAL PROCESSING METHOD THE MEANS OF PROCESSING FOR WHICH THE MATERIAL IS DESIGNED. SELECT REPLY CODE 10AC58 BGKJD 10SPEED,PROCESSING PROCESSING SPEED AN INDICATION OF THE SPEED AT WHICH AN ITEM MAY BE PROCESSED. SELECT REPLY CODE 10AG48 BGKKD 19CONTROL,GRAIN GRAIN CONTROL AN INDICATION OF THE DEGREE TO WHICH THE ITEM CAN CONTROL THE GRAIN SIZE. SELECT REPLY CODE 10AG49 BGKLD 19FUNCTION,ADDITIVE ADDITIVE FUNCTION AN INDICATION OF THE FUNCTION PERFORMED BY THE ADDITIVE. SELECT REPLY CODE 10AE74 BGKMD 01COLOR TONE PRODUCED COLOR TONE PRODUCED THE HUE,TINT,OR SHADING PRODUCED BY THE ITEM. SELECT REPLY CODE 10AD06 BGKND 19CONTRAST,IMAGE IMAGE CONTRAST AN INDICATION OF THE IMAGE TONE DENSITY PRODUCED BY THE ITEM. SELECT REPLY CODE 10AG49 BGKPJ /D/ 04WIDTH,CHART CHART WIDTH A MEASUREMENT OF THE WIDTH OF THE CHART WHEN USED IN CONJUNCTION WITH A SPECIFIC MEASUREMENT SCALE. 2D AND 1B MODE REPLY21AA052AG20 BGKQD 18TYPE,CISTERN CISTERN TYPE INDICATES THE TYPE OF CISTERN PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AL36 BGKRJ 04DIAMETER,BORE,TUBE TUBE BORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBE BORE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BGKSG 10ACCURACY,SCALE SCALE ACCURACY THE DEGREE OF CONFORMITY OF A SCALE MEASUREMENT TO A STANDARD OR A TRUE VALUE. FULL TEXT WRITE-IN 0 BGKTJ /D/T10RANGE,THERMOMETER THERMOMETER RANGE THE MINIMUM TO MAXIMUM VALUES WHICH THE THERMOMETER IS CAPABLE OF INDICATING. PLEASE USE MRC CJJM 1D AND 1F MODE REPLY13AJ40 BGKWD 18TYPE,CHART CHART TYPE INDICATES THE TYPE OF CHART PROVIDED. SELECT REPLY CODE 10AM12 BGKXJ 10UNIT,GRADUATION,THERMOMETER THERMOMETER GRADUATION UNIT THE INCREMENT OF MEASURE REPRESENTED BY THE MARKING/S/ ON THE THERMOMETER. 1D AND 1B MODE REPLY13AJ40 BGKYD /D/ 09MATERIAL,ELEMENT,ACTUATING ACTUATING ELEMENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH AN ACTUATING ELEMENT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH ISAC CODING IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 BGKZG /D/ 01COLOR,INSCRIPTION/BACKGROUND,SCALE SCALE INSCRIPTION/BACKGROUND COLOR THE HUE OR TINT OF THE INSCRIPTION(S) AND/OR THAT PORTION OF THE SCALE WHICH SURROUNDS THE INSCRIPTION ON THE SCALE. FULL TEXT WRITE-IN 0 BGLBJ 04LENGTH,SCALE SCALE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SCALE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BGLCD 19NAME FOR WHICH POINTER IS DESIGNED,SCALE SCALE NAME FOR WHICH POINTER IS DESIGNED INDICATES THE SCALE NAME FOR WHICH THE POINTER IS DESIGNED. SELECT REPLY CODE 10AL15 BGLDA 12QUANTITY,CHANNEL,INDIVIDUAL INDIVIDUAL CHANNEL QUANTITY THE NUMBER OF INDIVIDUAL CHANNELS PROVIDED. 1A MODE REPLY 0 BGLFF T10ACCURACY IN PERCENT,FREQUENCY FREQUENCY ACCURACY IN PERCENT AN INDICATION OF THE ACCURACY OF THE FREQUENCY,EXPRESSED IN PERCENT. 1F MODE REPLY 0 BGLGD /D/ 09MATERIAL,CRYSTAL CRYSTAL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CRYSTAL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BGLHJ /D/ 10FREQUENCY FOR WHICH DESIGNED,CRYSTAL CRYSTAL FREQUENCY FOR WHICH DESIGNED THE FREQUENCY AT WHICH THE CRYSTAL IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY11AC32 BGLJJ 04LENGTH,DRUM DRUM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A DRUM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BGLKJ 10ADJUSTMENT,LATERAL,DISK TABLE DISK TABLE LATERAL ADJUSTMENT AN INDICATION OF THE LATERAL ADJUSTMENT OF THE DISK TABLE. 2D AND 1B MODE REPLY21AA051AC20 BGLMJ 10ADJUSTMENT,VERTICAL,DISK TABLE DISK TABLE VERTICAL ADJUSTMENT AN INDICATION OF THE VERTICAL ADJUSTMENT OF THE DISK TABLE. 2D AND 1B MODE REPLY21AA051AC20 BGLNJ /D/ 04DIAMETER ACCOMMODATED,DISK DISK DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE DISK,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BGLPJ /D/ 04DIAMETER ACCOMMODATED,HOLE,ARBOR ARBOR HOLE DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ARBOR HOLE THE ITEM IS DESIGNED TO ACCOMMODATE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BGLQJ 04WIDTH,EDGE,CUTTING CUTTING EDGE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CUTTING EDGE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BGLRD 18TYPE,END,STRIKING STRIKING END TYPE INDICATES THE TYPE OF STRIKING END. SELECT REPLY CODE 10AN08 BGLSD 18TYPE,CURRENT,MAGNET MAGNET CURRENT TYPE INDICATES THE TYPE OF CURRENT WHETHER ALTERNATING,DIRECT,OR BOTH,OF THE MAGNET. SELECT REPLY CODE 10AB62 BGLTG 19NAME,MANUFACTURER,MAGNET MAGNET MANUFACTURER NAME THE NAME OF THE MANUFACTURER OF THE MAGNET. FULL TEXT WRITE-IN 0 BGLWD 11METHOD,ATTACHMENT,BLADE BLADE ATTACHMENT METHOD THE MEANS BY WHICH THE BLADE IS ATTACHED TO THE ITEM. SELECT REPLY CODE 10AB47 BGLXD 14SHAPE,CROSS-SECTIONAL,POINT POINT CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE POINT WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 BGLYJ 04DIAMETER,HOLE,PUNCHED PUNCHED HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PUNCHED HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BGMBJ 04DEPTH,MORTISE MORTISE DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE MORTISE,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BGMDA 12QUANTITY,OPENING,CHIP CHIP OPENING QUANTITY THE NUMBER OF CHIP OPENING(S) PROVIDED. 1A MODE REPLY 0 BGMFA /D/ 12QUANTITY,BORE BORE QUANTITY THE NUMBER OF BORE(S) IN THE ITEM. 1A MODE REPLY 0 BGMHJ 04DIAMETER,SHOULDER,FIRST FIRST SHOULDER DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BGMJJ 04LENGTH,FLAT FLAT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BGMKJ 04LENGTH,TANG,ROUND ROUND TANG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BGMLJ 04LENGTH,SHOULDER,FIRST FIRST SHOULDER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BGMMJ 04WIDTH,GROOVE,RETAINER RETAINER GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BGMNJ 04DIAMETER,GROOVE,RETAINER RETAINER GROOVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BGMPJ 04WIDTH ACROSS RETAINER FLATS WIDTH ACROSS RETAINER FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 BGMQJ /D/ 04TAPER TAPER NONE. 2D AND 1B MODE REPLY21AA051AC20 BGMRJ 04DISTANCE BETWEEN RETAINER GROOVE CENTER AND FLANGE DISTANCE BETWEEN RETAINER GROOVE CENTER AND FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BGMSJ 04DISTANCE BETWEEN SHANK END AND RETAINER GROOVE DISTANCE BETWEEN SHANK END AND RETAINER GROOVE NONE. 2D AND 1B MODE REPLY21AA051AC20 BGMWJ A04SIZE FOR WHICH DESIGNED,SOCKET,TAPER TAPER SOCKET SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE TAPER SOCKET FOR WHICH THE ITEM IS DESIGNED. 1D AND 1A MODE REPLY12AH09 BGMXD 18TYPE,TAPER TAPER TYPE INDICATES THE TYPE OF TAPER. SELECT REPLY CODE 10AK04 BGMYD 07COMPARISON,LENGTH,TAPER TAPER LENGTH COMPARISON AN INDICATION OF WHETHER OR NOT THE TAPER LENGTH/S/ IS EQUAL. SELECT REPLY CODE 10AL55 BGMZD 08LOCATION,BEVEL BEVEL LOCATION INDICATES THE LOCATION OF THE BEVEL ON THE ITEM. SELECT REPLY CODE 10AJ91 BGNBA 19NUMBER,STYLE,COMMERCIAL COMMERCIAL STYLE NUMBER AN INDICATION OF THE STYLE NUMBER BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1A MODE REPLY 0 BGNCJ /D/ 04DIAMETER,OUTSIDE,FERRULE FERRULE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FERRULE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BGNDD 18TYPE ACCOMMODATED,FASTENING FASTENING TYPE ACCOMMODATED INDICATES THE TYPE OF FASTENING DEVICE THE ITEM IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AC52 BGNFJ 04DIAMETER,OVERALL,BEZEL BEZEL OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF THE BEZEL. 2D AND 1B MODE REPLY21AA051AC20 BGNGJ 04DIAMETER,OVERALL,CASE CASE OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF THE CASE. 2D AND 1B MODE REPLY21AA051AC20 BGNHJ 04DEPTH,OVERALL,CASE CASE OVERALL DEPTH AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF A CASE,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BGNJD /D/ 07INDICATOR,BEAM,HIGH HEADLIGHT HIGH HEADLIGHT BEAM INDICATOR AN INDICATION OF WHETHER OR NOT A HIGH HEADLIGHT BEAM INDICATOR IS PROVIDED. SELECT REPLY CODE 10AB22 BGNKD /D/ 07GRADUATIONS/INDICATOR,MAJOR,LUMINOUS LUMINOUS MAJOR GRADUATIONS/INDICATOR AN INDICATION OF WHETHER OR NOT LUMINOUS MAJOR GRADUATIONS AND/OR LUMINOUS INDICATOR IS PROVIDED. SELECT REPLY CODE 10AB22 BGNLJ T10RANGE,MEASUREMENT MEASUREMENT RANGE THE MINIMUM AND MAXIMUM LIMITS OF MEASUREMENT INDICATED BY THE ITEM. 1D AND 1F MODE REPLY12AG67 BGNMJ 04LENGTH,ARM,FLOAT FLOAT ARM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FLOAT ARM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BGNNF T10RANGE,UNIT,GRAVITY GRAVITY UNIT RANGE THE RANGE OF GRAVITY UNITS FOR WHICH THE ITEM IS RATED. 1F MODE REPLY 0 BGNPF T10RANGE IN RPM,MEASUREMENT MEASUREMENT RANGE IN RPM THE MINIMUM TO MAXIMUM VALUES THE ITEM IS DESIGNED TO INDICATE,EXPRESSED IN REVOLUTIONS PER MINUTE. 1F MODE REPLY 0 BGNQA 12QUANTITY,ROW,REED REED ROW QUANTITY THE NUMBER OF REED ROW(S) PROVIDED. 1A MODE REPLY 0 BGNRA 12QUANTITY PER ROW,REED REED QUANTITY PER ROW THE NUMBER OF REED(S) IN EACH ROW. 1A MODE REPLY 0 BGNSJ /D/ 04DIAMETER,INSIDE,END CONNECTION END CONNECTION INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN END CONNECTION,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BGNTA 12QUANTITY BETWEEN REEDS,INTERVAL INTERVAL QUANTITY BETWEEN REEDS THE NUMBER OF INTERVAL(S) BETWEEN THE REEDS ON THE ITEM. 1A MODE REPLY 0 BGNWF T10RANGE IN RPM,MEASUREMENT,REED REED MEASUREMENT RANGE IN RPM THE MINIMUM TO MAXIMUM VALUES THE REEDS ARE DESIGNED TO INDICATE,EXPRESSED IN REVOLUTIONS PER MINUTE. 1F MODE REPLY 0 BGNXA 10REDUCTION IN RPM,FREQUENCY FREQUENCY REDUCTION IN RPM AN INDICATION OF THE REDUCTION IN FREQUENCY,EXPRESSED IN REVOLUTIONS PER MINUTE. 1A MODE REPLY 0 BGNYB 10INTERVAL IN SECONDS,TIME TIME INTERVAL IN SECONDS THE MEASUREMENT OF TIME BETWEEN EVENTS,EXPRESSED IN SECONDS. 1B MODE REPLY 0 BGNZD 19FINISH,SCALE SCALE FINISH AN INDICATION OF THE FINISH ON THE SCALE. SELECT REPLY CODE 10AB54 BGPBD /D/ 07SCALE,LUMINOUS LUMINOUS SCALE AN INDICATION OF WHETHER OR NOT A LUMINOUS SCALE IS PROVIDED. SELECT REPLY CODE 10AB22 BGPCD 05DIRECTION,MOVEMENT,POINTER POINTER MOVEMENT DIRECTION AN INDICATION OF THE DIRECTION IN WHICH THE POINTER MOVES. SELECT REPLY CODE 10AN16 BGPDA 10RATIO,MINIMUM,DRIVEN SPEED TO INDICATED SPEED DRIVEN SPEED TO INDICATED SPEED MINIMUM RATIO AN INDICATION OF THE MINIMUM RATIO OF THE DRIVEN SPEED TO THE INDICATED SPEED OF THE ITEM. 1A MODE REPLY 0 BGPFA 19NUMBER,MODEL,ACTUATOR ACTUATOR MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE ACTUATOR. 1A MODE REPLY 0 BGPGD /D/ 07MECHANISM,TOTALIZING TOTALIZING MECHANISM AN INDICATION OF WHETHER OR NOT A TOTALIZING MECHANISM IS PROVIDED. SELECT REPLY CODE 10AB22 BGPHD 10CALIBRATION,MECHANISM,TOTALIZING TOTALIZING MECHANISM CALIBRATION AN INDICATION OF THE CALIBRATION OF THE TOTALIZING MECHANISM. SELECT REPLY CODE 10AJ40 BGPJD /D/ 07SEMAPHORE,AHEAD-ASTERN AHEAD-ASTERN SEMAPHORE AN INDICATION OF WHETHER OR NOT AN AHEAD-ASTERN SEMAPHORE IS PROVIDED. SELECT REPLY CODE 10AB22 BGPKD /D/ 07SELECTOR,SPEED SPEED SELECTOR AN INDICATION OF WHETHER OR NOT A SPEED SELECTOR IS PROVIDED. SELECT REPLY CODE 10AB22 BGPLD /D/ 07RESET,MANUAL MANUAL RESET AN INDICATION OF WHETHER OR NOT A MANUAL RESET IS PROVIDED. SELECT REPLY CODE 10AB22 BGPMJ 04LENGTH,CABLE,TRANSMITTING TRANSMITTING CABLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TRANSMITTING CABLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BGPNJ T10RANGE,MEASUREMENT,SPEED SELECTOR SPEED SELECTOR MEASUREMENT RANGE THE MINIMUM TO MAXIMUM VALUES THE SPEED SELECTOR IS DESIGNED TO INDICATE. 1D AND 1F MODE REPLY12AG67 BGPPD 02DESIGN,CASE CASE DESIGN THE DESIGN OF THE CASE PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AK54 BGPQD 10UNIT,MEASUREMENT,SCALE SCALE MEASUREMENT UNIT AN INDICATION OF THE UNIT OF MEASURE FOR WHICH THE SCALE IS DESIGNED. SELECT REPLY CODE 10AG67 BGPRJ 04DIAMETER,HOLE,TUBE PIN TUBE PIN HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBE PIN HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BGPSG /D/ 10RATIO AT REFERENCE FREQUENCY,WAVE,VOLTAGE STANDING VOLTAGE STANDING WAVE RATIO AT REFERENCE FREQUENCY THE MAXIMUM TO MINIMUM VOLTAGE STANDING WAVE RATIO AT A SPECIFIED FREQUENCY/IES/. FULL TEXT WRITE-IN 0 BGPTD 11METHOD,COUPLING COUPLING METHOD THE MEANS USED TO COUPLE THE ITEM. SELECT REPLY CODE 10AH83 BGPWD 18TYPE,TUNING TUNING TYPE INDICATES THE TUNING TYPE OF THE ITEM. SELECT REPLY CODE 10AC01 BGPXB 10LOSS IN DECIBELS,POWER POWER LOSS IN DECIBELS THE AMOUNT OF DECREASE IN POWER,EXPRESSED IN DECIBELS. 1B MODE REPLY 0 BGPYG /D/ 19NAME,FITTING,TERMINAL TERMINAL FITTING NAME THE NOMENCLATURE BY WHICH THE TERMINAL FITTING IS IDENTIFIED. FULL TEXT WRITE-IN 0 BGPZG 19AGENCY,CONTROLLING,TERMINAL FITTING TERMINAL FITTING CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION THAT CONTROLS THE TERMINAL FITTING. FULL TEXT WRITE-IN 0 BGQBG /D/ 19NUMBER,IDENTIFYING,TERMINAL FITTING TERMINAL FITTING IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE TERMINAL FITTING. FULL TEXT WRITE-IN 0 BGQCD /D/ 02DESIGN,USAGE,TERMINAL FITTING TERMINAL FITTING USAGE DESIGN AN INDICATION OF THE DESIGNED USE OF THE TERMINAL FITTING. SELECT REPLY CODE 10AK54 BGQDJ 04WIDTH,CUT,BLADE BLADE CUT WIDTH THE WIDTH OF THE CUT THAT CAN BE MADE BY THE BLADE. 2D AND 1B MODE REPLY21AA051AC20 BGQFA 12QUANTITY,UNIT,POWER POWER UNIT QUANTITY THE NUMBER OF POWER UNITS PROVIDED. 1A MODE REPLY 0 BGQGA /D/ 12QUANTITY,UNIT,INDIVIDUAL POWER INDIVIDUAL POWER UNIT QUANTITY THE NUMBER OF INDIVIDUAL POWER UNITS PROVIDED. 1A MODE REPLY 0 BGQHD /D/ 07PARTS,ASSOCIATED ASSOCIATED PARTS AN INDICATION OF WHETHER OR NOT ASSOCIATED PARTS ARE INCLUDED. SELECT REPLY CODE 10AA49 BGQJD 19CHARACTERISTIC,BRIDGING,CIRCUIT CIRCUIT BRIDGING CHARACTERISTIC AN INDICATION OF THE CIRCUIT BRIDGING CHARACTERISTIC. SELECT REPLY CODE 10AD21 BGQKG 04SIZE,SCREEN SCREEN SIZE DESIGNATES THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE SCREEN. FULL TEXT WRITE-IN 0 BGQLD /D/ 07CIRCUITS,SWEEP SWEEP CIRCUITS AN INDICATION OF WHETHER OR NOT SWEEP CIRCUITS ARE INCLUDED. SELECT REPLY CODE 10AA49 BGQMD /D/ 07FEATURE,DRIVEN,GENERATOR GENERATOR DRIVEN FEATURE AN INDICATION OF WHETHER OR NOT A GENERATOR DRIVEN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BGQND 18TYPE,CIRCUIT,SWEEP SWEEP CIRCUIT TYPE INDICATES THE TYPE OF SWEEP CIRCUITS PROVIDED. SELECT REPLY CODE 10AK33 BGQPJ T10RANGE,FREQUENCY,SWEEP SWEEP FREQUENCY RANGE THE RANGE OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE SWEEP IS RATED. 1D AND 1F MODE REPLY11AC32 BGQQJ 10DURATION,SWEEP,SINGLE TRIGGER SINGLE TRIGGER SWEEP DURATION THE LENGTH OF TIME CONSUMED BY A SINGLE TRIGGER SWEEP. 2D AND 1B MODE REPLY22AB491AC20 BGQRJ 10WATTAGE RATING,OUTPUT OUTPUT WATTAGE RATING THE RATED OUTPUT POWER THAT AN ITEM CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS. 2D AND 1B MODE REPLY22AB491AC20 BGQSJ 10VOLT-AMPERE RATING VOLT-AMPERE RATING THE AMOUNT OF APPARENT POWER,AS DISTINGUISHED FROM TRUE POWER,FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY21AC331AC20 BGQTJ 10VOLTAGE RATING,OUTPUT,AC,LINE TO LINE LINE TO LINE AC OUTPUT VOLTAGE RATING THE TOTAL LINE TO LINE OUTPUT ALTERNATING CURRENT POTENTIAL FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY21AB631AC20 BGQWJ 10VOLTAGE RATING,INPUT,AC AC INPUT VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,OF ALTERNATING CURRENT POTENTIAL FOR WHICH THE INPUT OF AN ITEM IS RATED. 2D AND 1B MODE REPLY21AB631AC20 BGQXD /D/ 07PROTECTION,OVERLOAD OVERLOAD PROTECTION AN INDICATION OF WHETHER OR NOT OVERLOAD PROTECTION IS PROVIDED. SELECT REPLY CODE 10AB22 BGQYD /D/ 07FILTER,INTERFERENCE,RADIO RADIO INTERFERENCE FILTER AN INDICATION OF WHETHER OR NOT A RADIO INTERFERENCE FILTER IS PROVIDED. SELECT REPLY CODE 10AB22 BGQZD /D/ 09MATERIAL,SEMICONDUCTOR SEMICONDUCTOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SEMICONDUCTOR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BGRBD 19RELATIONSHIP TO INPUT VOLTAGE,VOLTAGE,DRIVE DRIVE VOLTAGE RELATIONSHIP TO INPUT VOLTAGE AN INDICATION OF WHETHER THE DRIVE VOLTAGE IS THE SAME AS,OR DIFFERENT FROM,THE INPUT VOLTAGE. SELECT REPLY CODE 10AL55 BGRCJ 10VOLTAGE RATING,DRIVE DRIVE VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,FOR WHICH THE DRIVE IS RATED. 3D AND 1B MODE REPLY31AB621AB631AC20 BGRDD 19RELATIONSHIP TO INPUT CURRENT,CURRENT,DRIVE DRIVE CURRENT RELATIONSHIP TO INPUT CURRENT AN INDICATION OF WHETHER THE DRIVE CURRENT IS THE SAME AS,OR DIFFRENT FROM,THE INPUT CURRENT. SELECT REPLY CODE 10AL55 BGRFJ 10CURRENT RATING,DRIVE DRIVE CURRENT RATING THE AMOUNT OF CURRENT FOR WHICH THE DRIVE IS RATED. 2D AND 1B MODE REPLY21AC301AC20 BGRGJ 10FREQUENCY RATING,DRIVE DRIVE FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE DRIVE IS RATED. 2D AND 1B MODE REPLY21AC321AC20 BGRHD /D/ 19RELATIONSHIP,VOLTAGE,OUTPUT/INPUT OUTPUT/INPUT VOLTAGE RELATIONSHIP AN INDICATION OF WHETHER THE OUTPUT VOLTAGE IS THE SAME AS,OR DIFFERENT FROM,THE INPUT VOLTAGE. SELECT REPLY CODE 10AL55 BGRJD 18TYPE,REED REED TYPE INDICATES THE TYPE OF REED PROVIDED. SELECT REPLY CODE 10AK54 BGRKD 19SEQUENCE,OPERATION,CONTACT CONTACT OPERATION SEQUENCE AN INDICATION OF WHETHER THE ITEM IS DESIGNED TO ACTUATE /MAKE/ A CONTACT BEFORE OR AFTER THE PRECEDING CONTACT DEACTUATES /BREAKS/. SELECT REPLY CODE 10AD78 BGRLJ 10VOLTAGE RATING,CONTACT CONTACT VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,FOR WHICH THE CONTACT IS RATED. 3D AND 1B MODE REPLY31AB621AB631AC20 BGRMJ 10CURRENT RATING,CONTACT CONTACT CURRENT RATING THE AMOUNT OF CURRENT FOR WHICH THE CONTACT IS RATED. 2D AND 1B MODE REPLY21AC301AC20 BGRNB 04ANGLE IN DEG,PHASE PHASE ANGLE IN DEG THE DIFFERENCE IN PHASE BETWEEN TWO ALTERNATING QUANTITIES HAVING THE SAME FREQUENCY,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BGRPJ 10TIME RATING IN DEG,DWELL DWELL TIME RATING IN DEG THAT PORTION OF EACH DRIVING CYCLE DURING WHICH ELECTRICAL CONTINUITY EXISTS BETWEEN THE CENTER CONTACT AND ONE STATIONARY CONTACT,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 BGRQD 18TYPE,CABLE CABLE TYPE INDICATES THE TYPE OF CABLE PROVIDED. SELECT REPLY CODE 10AC00 BGRRD /D/ 18TYPE,TERMINAL,CABLE CABLE TERMINAL TYPE INDICATES THE TYPE OF TERMINAL(S) FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. SELECT REPLY CODE 10AA58 BGRSD /D/ 07FEATURE,MOUNTING,PLUG IN PLUG IN MOUNTING FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE FOR PLUG IN MOUNTING IS PROVIDED. SELECT REPLY CODE 10AB22 BGRTG 03DESIGNATION,SIZE,BASE MOUNTING BASE MOUNTING SIZE DESIGNATION THE SIZE DESIGNATION OF THE MOUNTING BASE AS IT IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. FULL TEXT WRITE-IN 0 BGRWG 19ARRANGEMENT,PATTERN,TERMINAL TERMINAL PATTERN ARRANGEMENT AN INDICATION OF THE ARRANGEMENT OF THE TERMINAL PATTERN. FULL TEXT WRITE-IN 0 BGRXL 16STYLE,WIRING,BASE CONNECTION BASE CONNECTION WIRING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE WIRING OF THE BASE CONNECTION. 1L MODE REPLY 0 BGRYD 08LOCATION,CONNECTION CONNECTION LOCATION INDICATES THE CONNECTION LOCATION. SELECT REPLY CODE 10AJ91 BGRZJ 10AMPLITUDE RATING,VOLTAGE,TRIGGER SWEEP TRIGGER SWEEP VOLTAGE AMPLITUDE RATING THE MAXIMUM ABSOLUTE VALUE FOR WHICH THE TRIGGER SWEEP VOLTAGE IS RATED. 2D AND 1B MODE REPLY21AB631AC20 BGSBD /D/ 07SWITCH,POLARITY,TRIGGER SWEEP TRIGGER SWEEP POLARITY SWITCH AN INDICATION OF WHETHER OR NOT A TRIGGER SWEEP POLARITY SWITCH IS INCLUDED. SELECT REPLY CODE 10AA49 BGSCG /D/ 10INTERVALS,MARKER,TRIGGER SWEEP TRIGGER SWEEP MARKER INTERVALS THE DISTANCE BETWEEN INDICATED PULSE INTERVALS SHOWN ON THE SCREEN OF A TRIGGER SWEEP DESIGNED ITEM. FULL TEXT WRITE-IN 0 BGSDD /D/ 07SWEEP,EXPANDED EXPANDED SWEEP AN INDICATION OF WHETHER OR NOT AN EXPANDED SWEEP IS PROVIDED. SELECT REPLY CODE 10AB22 BGSFD /D/ 07FEATURE,SELF-PROPELLED SELF-PROPELLED FEATURE AN INDICATION OF WHETHER OR NOT A SELF-PROPELLED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BGSGJ 10SPEED,BELT BELT SPEED THE RATED SPEED OF THE BELT. 2D AND 1B MODE REPLY22AG671AC20 BGSHD /D/ 07UNIT,POWER POWER UNIT AN INDICATION OF WHETHER OR NOT A POWER UNIT IS INCLUDED. SELECT REPLY CODE 10AA49 BGSJJ 04LENGTH,OVERALL,HORIZONTAL HORIZONTAL OVERALL LENGTH THE DIMENSION MEASURED ALONG THE HORIZONTAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BGSKJ 04HEIGHT,DELIVERY,LOAD LOAD DELIVERY HEIGHT A MEASUREMENT OF THE HEIGHT(S) AT WHICH THE ITEM IS DESIGNED TO DELIVER A LOAD. 2D AND 1B MODE REPLY21AA051AC20 BGSLD /D/ 09MATERIAL,BELT BELT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BELT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH ISAC FOR BELT IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 BGSMD /D/ 07CLEATS,CARRYING,BELT BELT CARRYING CLEATS AN INDICATION OF WHETHER OR NOT BELT CARRYING CLEATS ARE INCLUDED. SELECT REPLY CODE 10AA49 BGSND 18TYPE,GUIDE,BELT BELT GUIDE TYPE INDICATES THE TYPE OF BELT GUIDE(S) PROVIDED ON THE ITEM. SELECT REPLY CODE 10AD58 BGSPA 12QUANTITY,RAIL,FRAME FRAME RAIL QUANTITY THE NUMBER OF RAIL(S) ON THE FRAME. 1A MODE REPLY 0 BGSQJ 04ANGLE IN DEG,ARC ARC ANGLE IN DEG THE ANGLE OF THE ARC,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 BGSRJ 04RADIUS,CENTERLINE CENTERLINE RADIUS A MEASUREMENT OF THE DISTANCE FROM THE CENTERLINE TO THE AXIS. 2D AND 1B MODE REPLY21AA051AC20 BGSSD 18TYPE,DEVICE,ROTATING ROTATING DEVICE TYPE INDICATES THE TYPE OF ROTATING DEVICE PROVIDED ON THE ITEM. SELECT REPLY CODE 10AC82 BGSTJ 10PRESSURE RATING PRESSURE RATING THE PRESSURE AT WHICH AN ITEM IS DESIGNED TO OPERATE. 2D AND 1B MODE REPLY22AG671AC20 BGSWJ 04DISTANCE BETWEEN ROTATING DEVICES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN ROTATING DEVICES THE CENTER TO CENTER DISTANCE BETWEEN THE ROTATING DEVICES. 1D AND 1B MODE REPLY11AA05 BGSXD /D/ 07STAND,FLOOR FLOOR STAND AN INDICATION OF WHETHER OR NOT A FLOOR STAND IS INCLUDED. SELECT REPLY CODE 10AA49 BGSYD /D/ 07COUPLING,END END COUPLING AN INDICATION OF WHETHER OR NOT AN END COUPLING(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BGSZJ 11METHOD,RATING,CAPACITY CAPACITY RATING METHOD THE MEANS USED TO DETERMINE THE CAPACITY OF THE ITEM. 2D AND 1B MODE REPLY22AG672AF50 BGTBH 19FACILITY,STORAGE STORAGE FACILITY THE STORAGE FACILITY STANDARDS ESTABLISHED TO ASSURE THE SERVICEABILITY OF SUPPLIES IN STORAGE. 3D MODE REPLY 31AN112AM812AN12 BGTCA 12QUANTITY,POST,FRAME FRAME POST QUANTITY THE NUMBER OF POST(S) PROVIDED FOR THE FRAME. 1A MODE REPLY 0 BGTDJ 04HEIGHT,POSITION,RAISED RAISED POSITION HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN ITEM WHILE IN A RAISED POSITION. 2D AND 1B MODE REPLY21AA051AC20 BGTFJ 04HEIGHT,POSITION,LOW LOW POSITION HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN ITEM WHILE IN A LOW POSITION. 2D AND 1B MODE REPLY21AA051AC20 BGTGD 07ADJUSTABILITY,SPACING,CENTER TO CENTER CENTER TO CENTER SPACING ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE CENTER TO CENTER SPACING IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BGTHJ 04DISTANCE BETWEEN FORKS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FORKS THE CENTER TO CENTER DISTANCE BETWEEN THE FORKS. 2D AND 1B MODE REPLY21AA051AC20 BGTJD /D/ 07TURNTABLE TURNTABLE AN INDICATION OF WHETHER OR NOT A TURNTABLE IS INCLUDED. SELECT REPLY CODE 10AA49 BGTKJ /D/ 04DIAMETER,TURNTABLE TURNTABLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR TURNTABLE,AND TERMINATES AT THE CIRCUMFERENCE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 BGTLJ 04HEIGHT FROM FLOOR,LOWEST,LIFT LIFT LOWEST HEIGHT FROM FLOOR A MEASUREMENT FROM THE FLOOR TO THE LIFT IN ITS LOWEST POSITION. 2D AND 1B MODE REPLY21AA051AC20 BGTMJ 04HEIGHT FROM FLOOR,HIGHEST,LIFT LIFT HIGHEST HEIGHT FROM FLOOR A MEASUREMENT FROM THE FLOOR TO THE LIFT IN ITS HIGHEST POSITION. 2D AND 1B MODE REPLY21AA051AC20 BGTND /D/ 07BASE,REVOLVING REVOLVING BASE AN INDICATION OF WHETHER OR NOT A REVOLVING BASE IS INCLUDED. SELECT REPLY CODE 10AA49 BGTPD /D/ 07RAIL,PLATFORM PLATFORM RAIL AN INDICATION OF WHETHER OR NOT A PLATFORM RAIL IS INCLUDED. SELECT REPLY CODE 10AA49 BGTQD /D/ 07FEATURE,REVERSING REVERSING FEATURE AN INDICATION OF WHETHER OR NOT A REVERSING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BGTRJ 04WIDTH,OVERALL,FLIGHT FLIGHT OVERALL WIDTH AN OVERALL MEASUREMENT OF THE FLIGHT WIDTH,IN DISTINCTION FROM LENGTH. 2D AND 1B MODE REPLY21AA051AC20 BGTSJ 04HEIGHT,OVERALL,FLIGHT FLIGHT OVERALL HEIGHT THE DISTANCE MEASURED FROM THE BOTTOM TO THE TOP OF THE FLIGHT. 2D AND 1B MODE REPLY21AA051AC20 BGTTJ 10UNIT,GRADUATION,SMALLEST SMALLEST GRADUATION UNIT THE SMALLEST INCREMENT OF MEASURE ON THE ITEM. 1D AND 1B MODE REPLY13AK09 BGTWD /D/ 07CRYSTAL,CALIBRATING,INTERNAL FREQUENCY INTERNAL FREQUENCY CALIBRATING CRYSTAL AN INDICATION OF WHETHER OR NOT AN INTERNAL FREQUENCY CALIBRATING CRYSTAL IS INCLUDED. SELECT REPLY CODE 10AA49 BGTXD /D/ 07COMPENSATOR,TEMPERATURE TEMPERATURE COMPENSATOR AN INDICATION OF WHETHER OR NOT A TEMPERATURE COMPENSATOR IS INCLUDED. SELECT REPLY CODE 10AA49 BGTYD 11METHOD,ADJUSTMENT,TUNING DEVICE TUNING DEVICE ADJUSTMENT METHOD THE MEANS USED TO ADJUST THE TUNING DEVICE. SELECT REPLY CODE 10AL41 BGTZD 18TYPE,LOOP,INDUCTIVE PICKUP INDUCTIVE PICKUP LOOP TYPE INDICATES THE TYPE OF INDUCTIVE PICKUP LOOP PROVIDED. SELECT REPLY CODE 10AL36 BGWBD /D/ 07CASE,BATTERY BATTERY CASE AN INDICATION OF WHETHER OR NOT A BATTERY CASE IS PROVIDED. SELECT REPLY CODE 10AB22 BGWCJ T10RANGE,POWER POWER RANGE THE MINIMUM AND MAXIMUM POWER TO WHICH THE ITEM WILL RESPOND. 1D AND 1F MODE REPLY11AC33 BGWDJ /D/ 10CYCLE,TIME TIME CYCLE THE PERIOD OF TIME COVERED BY THE ITEM. 1D AND 1B MODE REPLY13AJ40 BGWFJ 10VOLTAGE RATING AND TYPE VOLTAGE RATING AND TYPE INDICATES THE TYPE OF VOLTAGE AND THE RATED VALUE FOR WHICH THE ITEM IS DESIGNED. 3D AND 1B MODE REPLY31AB631AC202AD72 BGWGD 07FEATURE,FILTRATION FILTRATION FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM IS FILTERED. SELECT REPLY CODE 10AN10 BGWHD /D/ 19NUMBER,TRANSPARENCY,ASTM COLOR ASTM COLOR TRANSPARENCY NUMBER AN INDICATION OF THE COLOR TRANSPARENCY NUMBER ASSIGNED BY THE AMERICAN SOCIETY FOR TESTING AND MATERIALS. SELECT REPLY CODE 10AN13 BGWJD /D/ 19ADHESIVE FOR WHICH FORMULATED ADHESIVE FOR WHICH FORMULATED THE PARTICULAR ADHESIVE FOR WHICH THE ITEM IS FORMULATED. SELECT REPLY CODE 10AF11 BGWKD /D/ 19FILM FOR WHICH DESIGNED FILM FOR WHICH DESIGNED THE PARTICULAR KIND OF FILM FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BGWLD 19FEATURE,END,BASE BASE END FEATURE THE FEATURE OF THE BASE END ON THE ITEM. SELECT REPLY CODE 10AK84 BGWMJ /D/A19NUMBER,ACID ACID NUMBER THE NUMBER THAT REPRESENTS THE ACID CONDITION OF THE ITEM. 1D AND 1A MODE REPLY11AC20 BGWND /D/ 07FEATURE,BASE,RUBBER RUBBER BASE FEATURE AN INDICATION OF WHETHER OR NOT A RUBBER BASE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BGWPD 18TYPE,SURFACE,TREAD TREAD SURFACE TYPE INDICATES THE TYPE OF TREAD SURFACE ON THE ITEM. SELECT REPLY CODE 10AM35 BGWQH /D/ 19PROTECTION AND LOCATION,ENVIRONMENTAL ENVIRONMENTAL PROTECTION AND LOCATION THE ENVIRONMENTAL ELEMENTS OR CONDITIONS,AS RELATED TO A SPECIFIC AREA/S/ ON AN ITEM,FOR WHICH IT WAS DESIGNED TO WITHSTAND,AND ITS LOCATION. 2D MODE REPLY 22AA653AJ91 BGWRD /D/ 08LOCATION,FEATURE,NONMARKING NONMARKING FEATURE LOCATION INDICATES THE LOCATION OF THE NONMARKING FEATURE ON THE ITEM. SELECT REPLY CODE 10AJ91 BGWSD /D/ 07VALVE,RELEASE,AIR AIR RELEASE VALVE AN INDICATION OF WHETHER OR NOT AN AIR RELEASE VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 BGWTD /D/ 07INTERCHANGEABILITY,FOOT,LEFT-RIGHT LEFT-RIGHT FOOT INTERCHANGEABILITY AN INDICATION OF WHETHER OR NOT THE ITEM IS INTERCHANGEABLE WITH THE LEFT OR RIGHT FOOT. SELECT REPLY CODE 10AN15 BGWWD 18TYPE,BURNER,LIQUID FUEL LIQUID FUEL BURNER TYPE INDICATES THE TYPE OF LIQUID FUEL BURNER PROVIDED. SELECT REPLY CODE 10AH81 BGWXD /D/ 09MATERIAL,TOP,COOKING COOKING TOP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE COOKING TOP IS FABRICATED. SELECT REPLY CODE 10AD09 BGWYG 04SIZE,SURFACE,COOKING COOKING SURFACE SIZE DESIGNATES THE SIZE OF THE TOTAL COOKING SURFACE OF THE ITEM. FULL TEXT WRITE-IN 0 BGWZA 12QUANTITY,ZONE,HEAT HEAT ZONE QUANTITY THE NUMBER OF INDIVIDUAL HEAT ZONE(S) CONTAINED IN THE ITEM. 1A MODE REPLY 0 BGXBD /D/ 07GUTTER,GREASE,BUILT-IN BUILT-IN GREASE GUTTER AN INDICATION OF WHETHER OR NOT A BUILT-IN GREASE GUTTER IS INCLUDED. SELECT REPLY CODE 10AA49 BGXCD /D/ 07RECEPTACLE,GREASE,REMOVABLE REMOVABLE GREASE RECEPTACLE AN INDICATION OF WHETHER OR NOT A REMOVABLE GREASE RECEPTACLE IS INCLUDED. SELECT REPLY CODE 10AA49 BGXDA 12QUANTITY,RACK,INTERMEDIATE INTERMEDIATE RACK QUANTITY THE NUMBER OF INTERMEDIATE RACK(S) PROVIDED. 1A MODE REPLY 0 BGXFJ 10CAPACITY PER HOUR,FRYING,FOOD FOOD FRYING CAPACITY PER HOUR THE AMOUNT OF FOOD THE ITEM CAN FRY PER HOUR. 2D AND 1B MODE REPLY22AG674AE92 BGXGD /D/ 07HEATER HEATER AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A HEATER. SELECT REPLY CODE 10AB22 BGXHD /D/ 07JACKET,WATER WATER JACKET AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A WATER JACKET. SELECT REPLY CODE 10AB22 BGXJD 18TYPE,CONTAINER,GROUNDS GROUNDS CONTAINER TYPE INDICATES THE TYPE OF CONTAINER PROVIDED FOR HOLDING THE GROUNDS. SELECT REPLY CODE 10AF72 BGXKD 11METHOD,TRANSFERRING,WATER WATER TRANSFERRING METHOD THE MEANS PROVIDED FOR TRANSFERRING THE WATER. SELECT REPLY CODE 10AK43 BGXLD /D/ 07VALVE,SAFETY SAFETY VALVE AN INDICATION OF WHETHER OR NOT A SAFETY VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 BGXMA 12QUANTITY,TRAY TRAY QUANTITY THE NUMBER OF TRAYS PROVIDED WITH THE ITEM. 1A MODE REPLY 0 BGXND 18TYPE,TRAY TRAY TYPE INDICATES THE TYPE OF TRAY FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AK54 BGXPJ 04WIDTH,TRAY TRAY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TRAY,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BGXQJ /D/ 04DEPTH,TRAY TRAY DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON A TRAY,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BGXRD 18TYPE,CURRENT,PRIME MOVER PRIME MOVER CURRENT TYPE INDICATES THE TYPE OF CURRENT OF THE PRIME MOVER. SELECT REPLY CODE 10AB62 BGXSJ /D/ 10VOLTAGE RATING,MOVER,PRIME PRIME MOVER VOLTAGE RATING THE VALUE/S/ OF POTENTIAL FOR WHICH THE PRIME MOVER IS RATED. 2D AND 1B MODE REPLY21AB631AC20 BGXTJ /D/ 10FREQUENCY RATING,MOVER,PRIME PRIME MOVER FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE PRIME MOVER IS RATED. 2D AND 1B MODE REPLY21AC321AC20 BGXWD /D/ 19PHASE,MOVER,PRIME PRIME MOVER PHASE THE NUMBER OF ALTERNATING CURRENT PHASES OF THE PRIME MOVER. SELECT REPLY CODE 10AD02 BGXXD /D/ 07SYSTEM,INJECTION,STEAM STEAM INJECTION SYSTEM AN INDICATION OF WHETHER OR NOT A STEAM INJECTION SYSTEM IS INCLUDED. SELECT REPLY CODE 10AA49 BGXYD 18TYPE,CONVEYOR CONVEYOR TYPE INDICATES THE TYPE OF CONVEYOR PROVIDED. SELECT REPLY CODE 10AK97 BGXZA 12QUANTITY PER HOUR,RACK RACK QUANTITY PER HOUR THE NUMBER OF RACKS THE ITEM WILL HANDLE PER HOUR. 1A MODE REPLY 0 BGYBG 04SIZE ACCOMMODATED,RACK RACK SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE RACK THE ITEM WILL ACCOMMODATE. FULL TEXT WRITE-IN 0 BGYCJ /D/ 10VOLTAGE IN VOLTS,AC,OPERATING OPERATING AC VOLTAGE IN VOLTS THE ALTERNATING CURRENT VOLTAGE WHICH IS REQUIRED TO OPERATE THE ITEM,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 BGYDG 04SIZE,DEVICE,FASTENING FASTENING DEVICE SIZE DESIGNATES THE SIZE OF THE FASTENING DEVICE. FULL TEXT WRITE-IN 0 BGYFD /D/ 07PILOT,REMOVABLE REMOVABLE PILOT AN INDICATION OF WHETHER OR NOT A REMOVABLE PILOT IS PROVIDED. SELECT REPLY CODE 10AB22 BGYGD 18TYPE,TOOL TOOL TYPE INDICATES THE TYPE OF TOOL PROVIDED. SELECT REPLY CODE 10AJ57 BGYHJ 04DIAMETER,OUTSIDE,WORKING END WORKING END OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WORKING END,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BGYJJ 04DIAMETER,HOLE,AXIAL AXIAL HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE AXIAL HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BGYKD /D/ 18TYPE,FLUID,CONTAINER CONTAINER FLUID TYPE INDICATES THE TYPE OF FLUID USED IN THE CONTAINER. SELECT REPLY CODE 10AB75 BGYLB 10VOLTAGE DROP IN MILLIVOLTS VOLTAGE DROP IN MILLIVOLTS THE VOLTAGE DROP OF AN ITEM,EXPRESSED IN MILLIVOLTS. 1B MODE REPLY 0 BGYMJ T10RANGE,CURRENT CURRENT RANGE THE MINIMUM AND MAXIMUM CURRENT RATING FOR WHICH THE ITEM IS DESIGNED TO OPERATE. 1D AND 1F MODE REPLY11AC30 BGYND /D/ 07LEDGE LEDGE AN INDICATION OF WHETHER OR NOT A LEDGE IS INCLUDED. SELECT REPLY CODE 10AA49 BGYPJ 04WIDTH ABOVE LEDGE WIDTH ABOVE LEDGE A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH ABOVE THE LEDGE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BGYQJ 04DEPTH ABOVE LEDGE DEPTH ABOVE LEDGE A MEASUREMENT BETWEEN SPECIFIED POINTS ABOVE THE LEDGE,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BGYRJ 04HEIGHT ABOVE LEDGE HEIGHT ABOVE LEDGE A MEASUREMENT FROM THE BOTTOM TO THE TOP ABOVE THE LEDGE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BGYSA 12QUANTITY,SHELF,FIXED FIXED SHELF QUANTITY THE NUMBER OF FIXED SHELVES PROVIDED WITH THE ITEM. 1A MODE REPLY 0 BGYTA 12QUANTITY,SHELF,ADJUSTABLE ADJUSTABLE SHELF QUANTITY THE NUMBER OF ADJUSTABLE SHELVES PROVIDED WITH THE ITEM. 1A MODE REPLY 0 BGYWJ 10INTERVAL,ADJUSTMENT ADJUSTMENT INTERVAL THE MEASURED INTERVAL AT WHICH THE ITEM CAN BE ADJUSTED. 1D AND 1B MODE REPLY11AA05 BGYXA 12QUANTITY,DIVIDER,HORIZONTAL HORIZONTAL DIVIDER QUANTITY THE NUMBER OF HORIZONTAL DIVIDER(S) PROVIDED WITH THE ITEM. 1A MODE REPLY 0 BGYYJ 10INTERVAL,ADJUSTMENT,HORIZONTAL DIVIDER HORIZONTAL DIVIDER ADJUSTMENT INTERVAL THE MEASURED INTERVAL AT WHICH THE HORIZONTAL DIVIDER CAN BE ADJUSTED. 1D AND 1B MODE REPLY11AA05 BGYZA 12QUANTITY,DIVIDER,VERTICAL VERTICAL DIVIDER QUANTITY THE NUMBER OF VERTICAL DIVIDER(S) PROVIDED WITH THE ITEM. 1A MODE REPLY 0 BGZBJ 10INTERVAL,ADJUSTMENT,VERTICAL DIVIDER VERTICAL DIVIDER ADJUSTMENT INTERVAL THE MEASURED INTERVAL AT WHICH THE VERTICAL DIVIDER CAN BE ADJUSTED. 1D AND 1B MODE REPLY11AA05 BGZCJ 04DEPTH,COMPARTMENT COMPARTMENT DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF A COMPARTMENT,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BGZDJ 04HEIGHT,COMPARTMENT COMPARTMENT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A COMPARTMENT,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BGZFD /D/ 07BOX,SHELF SHELF BOX AN INDICATION OF WHETHER OR NOT A SHELF BOX IS FURNISHED. SELECT REPLY CODE 10AA55 BGZGA 12QUANTITY PER COMPARTMENT,BOX,SHELF SHELF BOX QUANTITY PER COMPARTMENT THE NUMBER OF SHELF BOX(ES) FOR EACH COMPARTMENT. 1A MODE REPLY 0 BGZHD 18TYPE,HOLDER,LABEL LABEL HOLDER TYPE INDICATES THE TYPE OF LABEL HOLDER PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AC58 BGZJD /D/ 07PANEL,END END PANEL AN INDICATION OF WHETHER OR NOT AN END PANEL IS PROVIDED. SELECT REPLY CODE 10AB22 BGZKD /D/ 07FEATURE,BACK,CLOSED CLOSED BACK FEATURE AN INDICATION OF WHETHER OR NOT A CLOSED BACK FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BGZLA 12QUANTITY,SHELF SHELF QUANTITY THE NUMBER OF SHELVES FURNISHED WITH THE ITEM. 1A MODE REPLY 0 BGZMD 07ADJUSTABILITY,SHELF SHELF ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE SHELF(VES) IS ADJUSTABLE. SELECT REPLY CODE 10AC06 BGZND /D/ 07LATCH,DRAWER DRAWER LATCH AN INDICATION OF WHETHER OR NOT A DRAWER LATCH IS PROVIDED. SELECT REPLY CODE 10AB22 BGZPJ 04HEIGHT,DRAWER DRAWER HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A DRAWER,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BGZQJ 04DEPTH,DRAWER DRAWER DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON A DRAWER,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BGZRD /D/ 07LOCK LOCK AN INDICATION OF WHETHER OR NOT A LOCK(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BGZSJ A12SIZE AND QUANTITY,COMPARTMENT COMPARTMENT SIZE AND QUANTITY DESIGNATES THE SIZE AND NUMBER OF COMPARTMENTS PROVIDED. 1D AND 1A MODE REPLY13AN14 BGZTD /D/ 07ADAPTER,CONVERSION,CARD SIZE CARD SIZE CONVERSION ADAPTER AN INDICATION OF WHETHER OR NOT AN ADAPTER/S/ FOR CONVERSION TO CARD SIZE IS FURNISHED. SELECT REPLY CODE 10AA55 BGZWG 04SIZE,CARD CARD SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE CARD. FULL TEXT WRITE-IN 0 BGZXB 10RESISTANCE RATING IN HOURS,FIRE FIRE RESISTANCE RATING IN HOURS THE LENGTH OF TIME IN WHICH THE ITEM WILL RESIST FIRE,EXPRESSED IN HOURS. 1B MODE REPLY 0 BGZYD /D/ 07DESIGN,USAGE,SEPARATE END PANEL SEPARATE END PANEL USAGE DESIGN AN INDICATION OF WHETHER OR NOT A SEPARATE END PANEL USAGE DESIGN IS INCLUDED. SELECT REPLY CODE 10AA49 BGZZA 12QUANTITY,DRAWER,VERTICAL ROW VERTICAL ROW DRAWER QUANTITY THE NUMBER OF DRAWER(S) PROVIDED ON THE VERTICAL ROW. 1A MODE REPLY 0 BHBBA 12QUANTITY,DRAWER,HORIZONTAL ROW HORIZONTAL ROW DRAWER QUANTITY THE NUMBER OF DRAWERS PROVIDED ON THE HORIZONTAL ROW. 1A MODE REPLY 0 BHBCD /D/ 07DRAWER,DIVIDED DIVIDED DRAWER AN INDICATION OF WHETHER OR NOT A DIVIDED DRAWER IS INCLUDED. SELECT REPLY CODE 10AA49 BHBDJ 04WIDTH,SCALE SCALE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A SCALE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BHBFA 12QUANTITY,DEVICE,RECORDING RECORDING DEVICE QUANTITY THE NUMBER OF RECORDING DEVICE(S) ON THE ITEM. 1A MODE REPLY 0 BHBGD 18TYPE,DEVICE,RECORDING RECORDING DEVICE TYPE INDICATES THE TYPE OF DEVICE USED FOR RECORDING. SELECT REPLY CODE 10AK54 BHBHJ 10CYCLE,TIME,SPRING SPRING TIME CYCLE THE PERIOD OF TIME FOR WHICH THE SPRING IS RATED. 1D AND 1B MODE REPLY13AJ40 BHBJD 11METHOD,WINDING,SPRING SPRING WINDING METHOD THE MEANS USED FOR WINDING THE SPRING. SELECT REPLY CODE 10AL27 BHBKD /D/ 07POINTER/SCALE POINTER/SCALE AN INDICATION OF WHETHER OR NOT A POINTER AND SCALE ARE INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BHBLD 01COLOR,CASE CASE COLOR THE HUE OR TINT OF THE CASE. SELECT REPLY CODE 10AD06 BHBMG /D/ 19TITLE AND DATE,DOCUMENT DOCUMENT TITLE AND DATE THE NAME AND DATE OF THE PRINTED DOCUMENT. FULL TEXT WRITE-IN 0 BHBNJ T10RANGE,SENSITIVITY SENSITIVITY RANGE THE MINIMUM AND MAXIMUM VALUES REPRESENTING THE SENSITIVITY OF THE ITEM. 1D AND 1F MODE REPLY13AK09 BHBPJ /D/ 04ANGLE IN DEG,VIEW VIEW ANGLE IN DEG THE ANGLE OF VIEW,EXPRESSED IN DEGREES. PLEASE USE MRC VANG IN PLACE OF THIS CANCELED MRC. 1D AND 1B MODE REPLY13AK33 BHBQD /D/ 07HOOD,TELESCOPING TELESCOPING HOOD AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A TELESCOPING HOOD. SELECT REPLY CODE 10AB22 BHBRD /D/ 07COVER,MULTIPLIER MULTIPLIER COVER AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A MULTIPLIER COVER. SELECT REPLY CODE 10AB22 BHBSD 18TYPE,CALCULATOR CALCULATOR TYPE INDICATES THE TYPE OF CALCULATOR PROVIDED. SELECT REPLY CODE 10AK54 BHBTA 12QUANTITY,CELL,LIGHT TARGET LIGHT TARGET CELL QUANTITY THE NUMBER OF LIGHT TARGET CELL(S) ON THE ITEM. 1A MODE REPLY 0 BHBWD 18TYPE,TARGET,LIGHT LIGHT TARGET TYPE INDICATES THE TYPE OF LIGHT TARGET PROVIDED. SELECT REPLY CODE 10AJ17 BHBXA 12QUANTITY,SCALE,DIAL DIAL SCALE QUANTITY THE NUMBER OF SCALE(S) ON THE DIAL. 1A MODE REPLY 0 BHBYF T10RANGE,MARKING,DIAL SCALE DIAL SCALE MARKING RANGE THE MINIMUM AND MAXIMUM MARKINGS ON A DIAL SCALE. 1F MODE REPLY 0 BHBZB 10INCREMENT,FOOTCANDLE,DIAL SCALE SMALLEST DIAL SCALE SMALLEST FOOTCANDLE INCREMENT THE SMALLEST INCREMENT OF GRADUATION,EXPRESSED IN FOOTCANDLES. 1B MODE REPLY 0 BHCBD /D/ 07SELECTOR,RANGE RANGE SELECTOR AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A RANGE SELECTOR. SELECT REPLY CODE 10AB22 BHCCJ 10FLOW RATE,LIQUID LIQUID FLOW RATE THE VOLUME OF LIQUID FLOWING THROUGH THE ITEM IN A GIVEN PERIOD OF TIME. 2D AND 1B MODE REPLY22AG201AC20 BHCDD 18TYPE,IMPELLER IMPELLER TYPE INDICATES THE TYPE OF ROTARY DEVICE PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AK04 BHCFD /D/ 07VANE,STRAIGHTENING STRAIGHTENING VANE AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A STRAIGHTENING VANE/S/. SELECT REPLY CODE 10AB22 BHCGD 18TYPE,REGISTER REGISTER TYPE INDICATES THE TYPE OF REGISTER PROVIDED ON THE ITEM. SELECT REPLY CODE 10AJ12 BHCHD /D/ 07FEATURE,RESET RESET FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A RESET FEATURE. SELECT REPLY CODE 10AB22 BHCJD /D/ 07MECHANISM,PRINTING PRINTING MECHANISM AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A PRINTING MECHANISM. SELECT REPLY CODE 10AB22 BHCKJ 04DIAMETER,FLANGE,INLET INLET FLANGE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN INLET FLANGE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BHCLD /D/ 07CONNECTION,UNION,INLET INLET UNION CONNECTION AN INDICATION OF WHETHER OR NOT THE INLET IS PROVIDED WITH A UNION CONNECTION. SELECT REPLY CODE 10AB22 BHCMG 04SIZE,CONNECTION,OUTLET OUTLET CONNECTION SIZE DESIGNATES THE SIZE OF THE OUTLET CONNECTION INCLUDED ON THE ITEM. FULL TEXT WRITE-IN 0 BHCNJ 04DIAMETER,FLANGE,OUTLET OUTLET FLANGE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN OUTLET FLANGE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BHCPJ 04WIDTH,FLANGE,OUTLET OUTLET FLANGE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE OUTLET FLANGE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BHCQJ 04LENGTH,FLANGE,OUTLET OUTLET FLANGE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE OUTLET FLANGE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BHCRJ 04THICKNESS,FLANGE,OUTLET OUTLET FLANGE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF AN OUTLET FLANGE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BHCSJ 04DIAMETER,CIRCLE,OUTLET BOLT OUTLET BOLT CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN OUTLET BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BHCTA 12QUANTITY,HOLE,OUTLET BOLT OUTLET BOLT HOLE QUANTITY THE NUMBER OF OUTLET BOLT HOLE(S) ON THE ITEM. 1A MODE REPLY 0 BHCWJ 04DIAMETER,HOLE,OUTLET BOLT OUTLET BOLT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN OUTLET BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BHCXD /D/ 07CONNECTION,UNION,OUTLET OUTLET UNION CONNECTION AN INDICATION OF WHETHER OR NOT THE OUTLET IS PROVIDED WITH A UNION CONNECTION. SELECT REPLY CODE 10AB22 BHCYG 04SIZE,END,TUBE TUBE END SIZE DESIGNATES THE SIZE OF THE TUBE END INCLUDED ON THE ITEM. FULL TEXT WRITE-IN 0 BHCZD /D/ 07CONNECTION,GAGE,PRESSURE PRESSURE GAGE CONNECTION AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A PRESSURE GAGE CONNECTION(S). SELECT REPLY CODE 10AB22 BHDBD 19CIRCUIT INDICATED,SCALE SCALE CIRCUIT INDICATED AN INDICATION OF THE CIRCUIT SPECIFIED ON THE SCALE. SELECT REPLY CODE 10AH81 BHDCD 18TYPE,GRADUATION,SCALE SCALE GRADUATION TYPE INDICATES THE TYPE OF GRADUATIONS PROVIDED ON THE SCALE. SELECT REPLY CODE 10AF63 BHDDD /D/ 07PROVISION,SENSITIVITY,AMPLIFIER DEFLECTION AMPLIFIER DEFLECTION SENSITIVITY PROVISION AN INDICATION OF WHETHER OR NOT PROVISIONS FOR RATING THE DEFLECTION SENSITIVITY THROUGH THE AMPLIFIER ARE PROVIDED. SELECT REPLY CODE 10AB22 BHDFJ 10VOLTAGE RATING,SENSITIVITY,VERTICAL DEFLECTION VERTICAL DEFLECTION SENSITIVITY VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,FOR WHICH THE VERTICAL DEFLECTION SENSITIVITY IS RATED. 3D AND 1B MODE REPLY31AB631AC201AF65 BHDGJ 10VOLTAGE RATING,SENSITIVITY,HORIZONTAL DEFLECTION HORIZONTAL DEFLECTION SENSITIVITY VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,FOR WHICH THE HORIZONTAL DEFLECTION SENSITIVITY IS RATED. 3D AND 1B MODE REPLY31AB631AC201AF65 BHDHD /D/ 07FEATURE,MODULATION,INPUT INTENSITY INPUT INTENSITY MODULATION FEATURE AN INDICATION OF WHETHER OR NOT AN INPUT INTENSITY MODULATION FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BHDJJ 10VOLTAGE RATING,SENSITIVITY,VISUAL MODULATION VISUAL MODULATION SENSITIVITY VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,AT WHICH THE VISUAL MODULATION SENSITIVITY IS RATED TO RESPOND. 2D AND 1B MODE REPLY21AB631AC20 BHDKJ 10VOLTAGE RATING,SENSITIVITY,VISUAL BLANKING VISUAL BLANKING SENSITIVITY VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,AT WHICH THE VISUAL BLANKING SENSITIVITY IS RATED TO RESPOND. 2D AND 1B MODE REPLY21AB631AC20 BHDLD /D/ 07PROVISION,SENSITIVITY,DIRECT CONNECTION DEFLECTION,PLATE PLATE DIRECT CONNECTION DEFLECTION SENSITIVITY PROVISION AN INDICATION OF WHETHER OR NOT PROVISIONS FOR RATING THE DIRECT CONNECTION TO THE PLATE DEFLECTION SENSITIVITY IS PROVIDED. SELECT REPLY CODE 10AB22 BHDMJ 10VOLTAGE RATING,SENSITIVITY,VERTICAL DEFLECTION,DIRECT CONNECTION DIRECT CONNECTION VERTICAL DEFLECTION SENSITIVITY VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,AT WHICH THE VERTICAL DEFLECTION FOR DIRECT CONNECTION IS RATED TO RESPOND. 3D AND 1B MODE REPLY31AB631AC201AF65 BHDNJ 10VOLTAGE RATING,SENSITIVITY,HORIZONTAL DEFLECTION,DIRECT CONNECTION DIRECT CONNECTION HORIZONTAL DEFLECTION SENSITIVITY VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,AT WHICH THE HORIZONTAL DEFLECTION FOR DIRECT CONNECTION IS RATED TO RESPOND. 3D AND 1B MODE REPLY31AB631AC201AF65 BHDPD /D/ 07RESPONSE RATING,FREQUENCY FREQUENCY RESPONSE RATING AN INDICATION OF WHETHER OR NOT A FREQUENCY RESPONSE RATING IS PROVIDED. SELECT REPLY CODE 10AB22 BHDQJ 10RESPONSE RATING,FREQUENCY,X-AXIS X-AXIS FREQUENCY RESPONSE RATING THE MINIMUM AND MAXIMUM FREQUENCIES TO WHICH THE X-AXIS WILL RESPOND. 2D AND 1B MODE REPLY21AC321AC20 BHDRJ 10RESPONSE RATING,FREQUENCY,Y-AXIS Y-AXIS FREQUENCY RESPONSE RATING THE MINIMUM AND MAXIMUM FREQUENCIES TO WHICH THE Y-AXIS WILL RESPOND. 2D AND 1B MODE REPLY21AC321AC20 BHDSJ 10RESPONSE RATING,FREQUENCY,Z-AXIS Z-AXIS FREQUENCY RESPONSE RATING THE MINIMUM AND MAXIMUM FREQUENCIES TO WHICH THE Z-AXIS WILL RESPOND. 2D AND 1B MODE REPLY21AC321AC20 BHDTD /D/ 07PROVISION,RATING,IMPEDANCE,AMPLIFIER INPUT AMPLIFIER INPUT IMPEDANCE RATING PROVISION AN INDICATION OF WHETHER OR NOT AMPLIFIER INPUT IMPEDANCE RATING IS PROVIDED. SELECT REPLY CODE 10AB22 BHDWJ 10IMPEDANCE RATING,INPUT,X-AXIS X-AXIS INPUT IMPEDANCE RATING THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) WHICH THE ITEM OFFERS TO THE X-AXIS INPUT FLOW OF ALTERNATING CURRENT. 2D AND 1B MODE REPLY21AA571AC20 BHDXJ 10IMPEDANCE RATING,INPUT,Y-AXIS Y-AXIS INPUT IMPEDANCE RATING THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) WHICH THE ITEM OFFERS TO THE Y-AXIS INPUT FLOW OF ALTERNATING CURRENT. 2D AND 1B MODE REPLY21AA571AC20 BHDYJ 10IMPEDANCE RATING,INPUT,Z-AXIS Z-AXIS INPUT IMPEDANCE RATING THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) WHICH THE ITEM OFFERS TO THE Z-AXIS INPUT FLOW OF ALTERNATING CURRENT. 2D AND 1B MODE REPLY21AA571AC20 BHDZD 19WAVEFORM,VOLTAGE,AMPLITUDE CALIBRATING AMPLITUDE CALIBRATING VOLTAGE WAVEFORM AN INDICATION OF THE SHAPE OF THE AMPLITUDE CALIBRATING VOLTAGE WAVEFORM. SELECT REPLY CODE 10AJ52 BHFBJ 10AMPLITUDE,PEAK TO PEAK,CALIBRATING CALIBRATING PEAK TO PEAK AMPLITUDE THE PEAK TO PEAK VALUE FOR WHICH THE ITEM IS CALIBRATED. 2D AND 1B MODE REPLY21AB631AC20 BHFCA 12QUANTITY,RANGE,MEASUREMENT MEASUREMENT RANGE QUANTITY THE NUMBER OF MEASUREMENT RANGES INCLUDED. 1A MODE REPLY 0 BHFDG /D/ 10STEPS,RANGE,MEASUREMENT MEASUREMENT RANGE STEPS AN INDICATION AS TO THE MEASUREMENT CAPABILITIES OF THE RANGE OR RANGES. FULL TEXT WRITE-IN 0 BHFFD /D/ 07SCALE,SCREEN,CALIBRATED CALIBRATED SCREEN SCALE AN INDICATION OF WHETHER OR NOT A CALIBRATED SCREEN SCALE IS INCLUDED. SELECT REPLY CODE 10AA49 BHFHD /D/ 07TUBE,STORAGE,TRACE TRACE STORAGE TUBE AN INDICATION OF WHETHER OR NOT A TRACE STORAGE TUBE IS INCLUDED. SELECT REPLY CODE 10AA49 BHFJJ 10SPEED,WRITING,STORAGE,MAXIMUM MAXIMUM STORAGE WRITING SPEED THE RATE OF WRITING ON SUCCESSIVE STORAGE ELEMENTS IN A CHARGE STORAGE TUBE. 1D AND 1B MODE REPLY12AG20 BHFKD 19POTENTIAL,STORAGE STORAGE POTENTIAL AN INDICATION OF THE STORAGE POTENTIAL OF THE ITEM. SELECT REPLY CODE 10AD63 BHFLA 12QUANTITY,GUN,WRITING WRITING GUN QUANTITY THE NUMBER OF WRITING GUN(S) INCLUDED WITH THE ITEM. 1A MODE REPLY 0 BHFMJ 10VOLTAGE,ACCELERATING,WRITING GUN WRITING GUN ACCELERATING VOLTAGE THE ACCELERATING VOLTAGE FOR WHICH THE WRITING GUN IS RATED. 1D AND 1B MODE REPLY11AB63 BHFNA 12QUANTITY,GUN,FLOOD FLOOD GUN QUANTITY THE NUMBER OF FLOOD GUN(S) PROVIDED. 1A MODE REPLY 0 BHFPJ /D/ 10VOLTAGE,ACCELERATING,FLOOD GUN FLOOD GUN ACCELERATING VOLTAGE THE ACCELERATING VOLTAGE FOR WHICH THE FLOOD GUN IS RATED. 1D AND 1B MODE REPLY11AB63 BHFQJ 10VOLTAGE RATING,SCREEN,VIEWING VIEWING SCREEN VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,FOR WHICH THE VIEWING SCREEN IS RATED. 1D AND 1B MODE REPLY11AB63 BHFRD /D/ 07PROVISION,ERASING,TRACE TRACE ERASING PROVISION AN INDICATION OF WHETHER OR NOT TRACE ERASING PROVISIONS ARE PROVIDED. SELECT REPLY CODE 10AB22 BHFSG /D/ 19FUNCTION AND QUANTITY,UNIT,PLUG IN PLUG IN UNIT FUNCTION AND QUANTITY AN INDICATION OF THE FUNCTION OF THE PLUG IN UNITS AND THE NUMBER PROVIDED. FULL TEXT WRITE-IN 0 BHFTD /D/ 07ACCOMMODATION,DEVICE,RECORDING,CAMERA CAMERA RECORDING DEVICE ACCOMMODATION AN INDICATION OF WHETHER OR NOT CAMERA RECORDING DEVICE ACCOMMODATIONS ARE PROVIDED. SELECT REPLY CODE 10AB22 BHFWJ 10FREQUENCY RATING,FIXED FIXED FREQUENCY RATING THE FIXED NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY11AC32 BHFXA 12QUANTITY,FREQUENCY,FIXED FIXED FREQUENCY QUANTITY THE NUMBER OF FIXED FREQUENCIES PROVIDED. 1A MODE REPLY 0 BHFYD /D/ 07FEATURE,CONTROLLED,CRYSTAL CRYSTAL CONTROLLED FEATURE AN INDICATION OF WHETHER OR NOT A CRYSTAL CONTROLLED FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BHFZG /D/ 10RANGE,OUTPUT,CALIBRATED SIGNAL CALIBRATED SIGNAL OUTPUT RANGE AN INDICATION OF THE CALIBRATED SIGNAL RANGE THAT IS OUTPUT BY THE ITEM. FULL TEXT WRITE-IN 0 BHGBG /D/ 10OUTPUT,SIGNAL,MAXIMUM MAXIMUM SIGNAL OUTPUT AN INDICATION OF THE MAXIMUM SIGNAL OUTPUT TRANSMITTED BY THE ITEM. FULL TEXT WRITE-IN 0 BHGCG /D/ 10CONSTANCY,OUTPUT,SIGNAL SIGNAL OUTPUT CONSTANCY AN INDICATION OF THE SIGNAL OUTPUT CONSTANCY. FULL TEXT WRITE-IN 0 BHGDD 08LOCATION,MODULATOR MODULATOR LOCATION INDICATES THE LOCATION OF THE MODULATOR ON THE ITEM. SELECT REPLY CODE 10AJ91 BHGFJ 04DIAMETER FOR WHICH DESIGNED,METER METER DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE METER FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BHGGG /D/ 10RANGE,STRENGTH,FIELD FIELD STRENGTH RANGE THE LOWER AND UPPER LIMITS OF ELECTRICAL INTENSITY OF RADIATED ELECTROMAGNETIC ENERGY. FULL TEXT WRITE-IN 0 BHGHA 12QUANTITY,POSITION,BAND SWITCH BAND SWITCH POSITION QUANTITY THE NUMBER OF BAND SWITCH POSITION(S) PROVIDED. 1A MODE REPLY 0 BHGJA 12QUANTITY,UNIT,PLUG-IN PLUG-IN UNIT QUANTITY THE NUMBER OF PLUG-IN UNITS PROVIDED. 1A MODE REPLY 0 BHGKA 12QUANTITY,METER,INDIVIDUAL INDIVIDUAL METER QUANTITY THE NUMBER OF INDIVIDUAL METER(S) OF A SPECIFIC TYPE. 1A MODE REPLY 0 BHGLG 19AGENCY,CONTROLLING,INDIVIDUAL METER INDIVIDUAL METER CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE INDIVIDUAL METER. FULL TEXT WRITE-IN 0 BHGMG 19NAME,METER,INDIVIDUAL INDIVIDUAL METER NAME THE NOMENCLATURE BY WHICH THE INDIVIDUAL METER IS IDENTIFIED. FULL TEXT WRITE-IN 0 BHGNG /D/ 19NUMBER,IDENTIFYING,INDIVIDUAL METER INDIVIDUAL METER IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE INDIVIDUAL METER. FULL TEXT WRITE-IN 0 BHGPD 18TYPE,CURRENT,INDIVIDUAL METER INDIVIDUAL METER CURRENT TYPE INDICATES THE TYPE OF CURRENT FOR WHICH THE INDIVIDUAL METER IS DESIGNED. SELECT REPLY CODE 10AB62 BHGQG /D/ 10RANGE,MEASUREMENT,INDIVIDUAL METER INDIVIDUAL METER MEASUREMENT RANGE THE MINIMUM AND MAXIMUM VALUES THAT AN INDIVIDUAL METER WILL INDICATE,RECORD,DETECT,OR CONTROL. FULL TEXT WRITE-IN 0 BHGRD /D/ 09MATERIAL,PANEL,MOUNTING MOUNTING PANEL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MOUNTING PANEL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BHGSD 18TYPE,CIRCULATION CIRCULATION TYPE INDICATES THE TYPE OF CIRCULATION PROVIDED. SELECT REPLY CODE 10AL51 BHGTD 11METHOD,CIRCULATION CIRCULATION METHOD THE MEANS USED TO PROVIDE CIRCULATION. SELECT REPLY CODE 10AM42 BHGWA 12QUANTITY,THERMOMETER THERMOMETER QUANTITY THE NUMBER OF THERMOMETERS ON THE ITEM. 1A MODE REPLY 0 BHGXD /D/ 07STEM,THERMOMETER,ENGRAVED ENGRAVED THERMOMETER STEM AN INDICATION OF WHETHER OR NOT AN ENGRAVED THERMOMETER STEM IS INCLUDED. SELECT REPLY CODE 10AA49 BHGYD 18TYPE,FILLING,THERMOMETER THERMOMETER FILLING TYPE INDICATES THE TYPE OF SUBSTANCE WITH WHICH THE THERMOMETER IS FILLED. SELECT REPLY CODE 10AD52 BHGZD 11METHOD,MOUNTING,THERMOMETER THERMOMETER MOUNTING METHOD THE MEANS OF ATTACHING THE THERMOMETER. SELECT REPLY CODE 10AM39 BHHBD /D/ 09MATERIAL,MOUNTING,THERMOMETER THERMOMETER MOUNTING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE THERMOMETER MOUNTING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BHHCD /D/ 17SURFACE TREATMENT,MOUNTING,THERMOMETER THERMOMETER MOUNTING SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE THERMOMETER MOUNTING SURFACE. SELECT REPLY CODE 10AD09 BHHDD /D/ 09MATERIAL,CISTERN CISTERN MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CISTERN IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BHHFD /D/ 07HANDLE,SLING SLING HANDLE AN INDICATION OF WHETHER OR NOT A SLING HANDLE IS INCLUDED. SELECT REPLY CODE 10AA49 BHHGD /D/ 07SHELTER,MOUNTING MOUNTING SHELTER AN INDICATION OF WHETHER OR NOT A MOUNTING SHELTER IS INCLUDED. SELECT REPLY CODE 10AA49 BHHHD /D/ 07TABLES,PANEL,MOUNTING MOUNTING PANEL TABLES AN INDICATION OF WHETHER OR NOT TABLES ARE PROVIDED ON THE MOUNTING PANEL. SELECT REPLY CODE 10AB22 BHHJD 18TYPE,INDICATION INDICATION TYPE INDICATES THE TYPE OF INDICATION PROVIDED BY THE ITEM. SELECT REPLY CODE 10AM05 BHHKA 12QUANTITY,ELEMENT ELEMENT QUANTITY THE NUMBER OF ELEMENTS IN THE ITEM. 1A MODE REPLY 0 BHHLL 16STYLE,CASE CASE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CASE. 1L MODE REPLY 0 BHHMD 14SHAPE,COVER,CASE CASE COVER SHAPE THE PHYSICAL CONFIGURATION OF THE CASE COVER. SELECT REPLY CODE 10AD07 BHHND /D/ 09MATERIAL,COVER,CASE CASE COVER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CASE COVER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BHHPJ /D/A18TYPE AND QUANTITY,TRANSFORMER TRANSFORMER TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF TRANSFORMER(S) REQUIRED FOR OPERATION. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1D AND 1A MODE REPLY12AK38 BHHQD /D/ 18TYPE,DRIVE,RECORDING DEVICE RECORDING DEVICE DRIVE TYPE INDICATES THE TYPE OF DRIVE PROVIDED FOR THE RECORDING DEVICE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AG25 BHHRG /D/ 19NAME,MANUFACTURER,RECORDING DEVICE RECORDING DEVICE MANUFACTURER NAME THE NAME OF THE COMMERCIAL ORGANIZATION WHICH MANUFACTURES THE RECORDING DEVICE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. FULL TEXT WRITE-IN 0 BHHSG /D/ 19NUMBER,IDENTIFYING,CHART CHART IDENTIFYING NUMBER THE NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE CHART. FULL TEXT WRITE-IN 0 BHHTJ 10MEASUREMENT,MAXIMUM,REGISTER REGISTER MAXIMUM MEASUREMENT THE MAXIMUM VALUE THAT CAN BE MEASURED BY THE ITEM. 1D AND 1B MODE REPLY13AK09 BHHWJ 04DIAMETER,ACCOMMODATED,MATERIAL MATERIAL ACCOMMODATED DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MATERIAL ACCOMMODATED,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BHHXJ T10RANGE,CHART,CONVERSION CONVERSION CHART RANGE THE LOWER AND UPPER LIMITS OF THE CONVERSION CHART. 1D AND 1F MODE REPLY12AG67 BHHYD /D/ 07ADJUSTER,ANGLE,DEFLECTION DEFLECTION ANGLE ADJUSTER AN INDICATION OF WHETHER OR NOT A DEFLECTION ANGLE ADJUSTER IS INCLUDED. SELECT REPLY CODE 10AA49 BHHZD /D/ 07CIRCUIT,RECTIFIER RECTIFIER CIRCUIT AN INDICATION OF WHETHER OR NOT A RECTIFIER CIRCUIT IS PROVIDED. SELECT REPLY CODE 10AB22 BHJBJ /D/ 10CURRENT RATING,DEFLECTION,FULL SCALE FULL SCALE DEFLECTION CURRENT RATING THE AMOUNT OF CURRENT REQUIRED FOR FULL SCALE DEFLECTION. 1D AND 1B MODE REPLY11AC30 BHJCD /D/ 18TYPE,SCALE,NONLINEAR NONLINEAR SCALE TYPE INDICATES THE TYPE OF NONLINEAR SCALE PROVIDED. SELECT REPLY CODE 10AA62 BHJDD /D/ 07MARKINGS,LUMINOUS LUMINOUS MARKINGS AN INDICATION OF WHETHER OR NOT LUMINOUS MARKINGS ARE PROVIDED ON THE ITEM. SELECT REPLY CODE 10AB22 BHJFA 12QUANTITY,DIVIDER DIVIDER QUANTITY THE NUMBER OF DIVIDER(S) PROVIDED. 1A MODE REPLY 0 BHJGD 19POSITION,DIVIDER DIVIDER POSITION THE POSITION OF THE DIVIDER OF THE ITEM. SELECT REPLY CODE 10AF63 BHJHD /D/ 07DRAWER,FRONT,DROP DROP FRONT DRAWER AN INDICATION OF WHETHER OR NOT A DROP FRONT DRAWER IS INCLUDED. SELECT REPLY CODE 10AA49 BHJJA 12QUANTITY,TRAY,REMOVABLE,DRAWER DRAWER REMOVABLE TRAY QUANTITY THE NUMBER OF REMOVABLE TRAY(S) PROVIDED WITH THE DRAWER. 1A MODE REPLY 0 BHJKD 08LOCATION,READING,DIAL DIAL READING LOCATION INDICATES THE READING LOCATION ON THE DIAL. SELECT REPLY CODE 10AJ91 BHJLD 11METHOD,CHANGE,COMBINATION COMBINATION CHANGE METHOD THE MEANS BY WHICH THE COMBINATION IS CHANGED. SELECT REPLY CODE 10AL88 BHJMD 02DESIGN,LOCKING LOCKING DESIGN THE DESIGN OF THE LOCKING MECHANISM OF THE ITEM. SELECT REPLY CODE 10AJ17 BHJND /D/ 07CLIP,BULKHEAD BULKHEAD CLIP AN INDICATION OF WHETHER OR NOT A BULKHEAD CLIP(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BHJPA /D/ 19IDENTIFICATION,SHADE,FED STD 595 FED STD 595 SHADE IDENTIFICATION A DESIGNATION ASSIGNED IN FEDERAL STANDARD 595 TO A PARTICULAR GRADATION OF A COLOR FOR PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 BHJQD /D/ 07DOOR DOOR AN INDICATION OF WHETHER OR NOT A DOOR(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BHJRD /D/ 07COMPRESSOR COMPRESSOR AN INDICATION OF WHETHER OR NOT A COMPRESSOR(S) IS FURNISHED. SELECT REPLY CODE 10AA55 BHJSD /D/ 07DIVIDER DIVIDER AN INDICATION OF WHETHER OR NOT A DIVIDER(S) IS FURNISHED. SELECT REPLY CODE 10AA55 BHJTD /D/ 07BASE BASE AN INDICATION OF WHETHER OR NOT A BASE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BHJWD /D/ 07SHELF,POSTING POSTING SHELF AN INDICATION OF WHETHER OR NOT A POSTING SHELF(VES) IS FURNISHED. SELECT REPLY CODE 10AA55 BHJXJ 04HEIGHT ACCOMMODATED,PLATE PLATE HEIGHT ACCOMMODATED A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE ACCOMMODATED PLATE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BHJYJ 04WIDTH ACCOMMODATED,PLATE PLATE WIDTH ACCOMMODATED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ACCOMMODATED PLATE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BHJZA 19CAPACITY,PLATE,ADDRESS ADDRESS PLATE CAPACITY THE NUMBER OF ADDRESS PLATE(S) THE ITEM CAN ACCOMMODATE. 1A MODE REPLY 0 BHKBJ /D/ 04DEPTH,FILING FILING DEPTH THE MEASUREMENT BETWEEN SPECIFIED POINTS OF THE ITEM WHICH CAN BE USED FOR FILING,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BHKCJ 04WIDTH,FORM FORM WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FORM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BHKDD /D/ 07ROD,GUIDE GUIDE ROD AN INDICATION OF WHETHER OR NOT A GUIDE ROD(S) IS FURNISHED. SELECT REPLY CODE 10AA55 BHKFD 04SIZE,UNIT UNIT SIZE DESIGNATES THE SIZE BY WHICH THE UNIT IS KNOWN AND/OR IDENTIFIED. SELECT REPLY CODE 10AN14 BHKGD 18TYPE,BRACE BRACE TYPE INDICATES THE TYPE OF BRACE PROVIDED. SELECT REPLY CODE 10AH28 BHKHA 19CAPACITY,KEY KEY CAPACITY THE NUMBER OF KEYS THE ITEM CAN ACCOMMODATE. 1A MODE REPLY 0 BHKJD 11METHOD,HOLDING,KEY KEY HOLDING METHOD THE MEANS UTILIZED TO HOLD THE KEY(S). SELECT REPLY CODE 10AF39 BHKKA 12QUANTITY,DRAWER,KEY HOLDING KEY HOLDING DRAWER QUANTITY THE NUMBER OF KEY HOLDING DRAWERS PROVIDED WITH THE ITEM. 1A MODE REPLY 0 BHKLD /D/ 07PANEL,DOOR,GLASS GLASS DOOR PANEL AN INDICATION OF WHETHER OR NOT A GLASS DOOR PANEL(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BHKMA 12QUANTITY,PANEL,KEY HOLDING KEY HOLDING PANEL QUANTITY THE NUMBER OF KEY HOLDING PANELS PROVIDED WITH THE ITEM. 1A MODE REPLY 0 BHKND /D/ 07TAG,KEY KEY TAG AN INDICATION OF WHETHER OR NOT A KEY TAG/S/ IS FURNISHED. SELECT REPLY CODE 10AA55 BHKPD /D/ 07FEATURE,LOCK,CHANGEABLE CHANGEABLE LOCK FEATURE AN INDICATION OF WHETHER OR NOT A CHANGEABLE LOCK FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BHKQD /D/ 19ARRANGEMENT,GROUPING,FIRST FIRST GROUPING ARRANGEMENT THE CONDUCTORS IDENTIFIED IN THE FIRST GROUP. SELECT REPLY CODE 10AJ91 BHKRD /D/ 19ARRANGEMENT,GROUPING,SECOND SECOND GROUPING ARRANGEMENT THE CONDUCTORS IDENTIFIED IN THE SECOND GROUP. SELECT REPLY CODE 10AJ91 BHKSD /D/ 19ARRANGEMENT,GROUPING,THIRD THIRD GROUPING ARRANGEMENT THE CONDUCTORS IDENTIFIED IN THE THIRD GROUP. SELECT REPLY CODE 10AJ91 BHKTD /D/ 19ARRANGEMENT,GROUPING,FOURTH FOURTH GROUPING ARRANGEMENT THE CONDUCTORS IDENTIFIED IN THE FOURTH GROUP. SELECT REPLY CODE 10AJ91 BHKWD /D/ 19ARRANGEMENT,GROUPING,FIFTH FIFTH GROUPING ARRANGEMENT THE CONDUCTORS IDENTIFIED IN THE FIFTH GROUP. SELECT REPLY CODE 10AJ91 BHKXJ /D/A19ARRANGEMENT AND QUANTITY,GROUPING,CONDUCTOR CONDUCTOR GROUPING ARRANGEMENT AND QUANTITY THE GROUPING ARRANGEMENT AND THE NUMBER OF GROUPS INTO WHICH TWO OR MORE CONDUCTORS ARE ARRANGED. 1D AND 1A MODE REPLY12AK80 BHKYG 10UL RATING UL RATING THE RATING ISSUED TO THE ITEM BY THE UNDERWRITERS LABORATORIES. FULL TEXT WRITE-IN 0 BHKZA 12QUANTITY,LOCK,DRAWER KEY DRAWER KEY LOCK QUANTITY THE NUMBER OF DRAWERS EQUIPPED WITH A KEY LOCK. 1A MODE REPLY 0 BHLBJ 10RESISTANCE RATING RESISTANCE RATING THE RATED RESISTANCE OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BHLCD /D/ 07DEVICE,OPTICAL OPTICAL DEVICE AN INDICATION OF WHETHER OR NOT AN OPTICAL DEVICE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BHLDD /D/ 07DEVICE,ESCAPE ESCAPE DEVICE AN INDICATION OF WHETHER SELECT REPLY CODE 10AA49 BHLFD /D/ 07FEATURE,ACTIVATION,ULTRAVIOLET LIGHT ULTRAVIOLET LIGHT ACTIVATION FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE IS INCLUDED FOR ULTRAVIOLET LIGHT ACTIVATION. SELECT REPLY CODE 10AA49 BHLGD /D/ 07POINTER,ADJUSTABLE ADJUSTABLE POINTER AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH AN ADJUSTABLE POINTER. SELECT REPLY CODE 10AB22 BHLHD /D/ 07RING,INSULATING INSULATING RING AN INDICATION OF WHETHER OR NOT AN INSULATING RING IS PROVIDED. SELECT REPLY CODE 10AB22 BHLJD /D/ 07RING,RETAINING RETAINING RING AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A RETAINING RING. SELECT REPLY CODE 10AB22 BHLKD /D/ 07WINDOW,ILLUMINATION,AUXILIARY AUXILIARY ILLUMINATION WINDOW AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH AN AUXILIARY ILLUMINATION WINDOW. SELECT REPLY CODE 10AB22 BHLLA 12QUANTITY,REED REED QUANTITY THE NUMBER OF REED(S) IN THE ITEM. 1A MODE REPLY 0 BHLMJ 10FREQUENCY RATING,CENTER CENTER FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE CENTER IS RATED. 1D AND 1B MODE REPLY11AC32 BHLNB 10MEASUREMENT,MAXIMUM MAXIMUM MEASUREMENT THE HIGHEST VALUE THE ITEM CAN INDICATE. 1B MODE REPLY 0 BHLPG 01COLOR,MARKING MARKING COLOR THE HUE OR TINT OF THE MARKING(S) ON THE ITEM. FULL TEXT WRITE-IN 0 BHLQG 01COLOR,BACKGROUND BACKGROUND COLOR THE HUE OR TINT OF THE BACKGROUND OF THE ITEM. FULL TEXT WRITE-IN 0 BHLRD 18TYPE,MOVEMENT,ELECTRICAL ELECTRICAL MOVEMENT TYPE INDICATES THE TYPE OF ELECTRICAL MOVEMENT PROVIDED. SELECT REPLY CODE 10AC58 BHLSJ /D/ 04WIDTH,CHART CHART WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CHART,IN DISTINCTION FROM THICKNESS. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 BHLTJ /D/ 04LENGTH,CHART CHART LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CHART,IN DISTINCTION FROM WIDTH. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 BHLWD 18TYPE,POINT,INDICATING INDICATING POINT TYPE INDICATES THE TYPE OF INDICATING POINT PROVIDED. SELECT REPLY CODE 10AJ44 BHLXJ /D/ 04WIDTH,SLOT,AA ARM AA ARM SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BHLYJ /D/ 04WIDTH,SLOT,HORIZONTAL,BB ARM BB ARM HORIZONTAL SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BHLZG 18TYPE,SWITCH,CONTROL CONTROL SWITCH TYPE INDICATES THE TYPE OF CONTROL SWITCH. FULL TEXT WRITE-IN 0 BHMBA 12QUANTITY,POSITION,OFF OFF POSITION QUANTITY THE NUMBER OF OFF POSITION(S) PROVIDED. 1A MODE REPLY 0 BHMCD 18TYPE,CASE CASE TYPE INDICATES THE TYPE OF CASE PROVIDED. SELECT REPLY CODE 10AJ95 BHMDD 18TYPE,BEZEL BEZEL TYPE INDICATES THE TYPE OF BEZEL PROVIDED. SELECT REPLY CODE 10AM39 BHMFD /D/ 09MATERIAL,CRYSTAL,PROTECTIVE PROTECTIVE CRYSTAL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PROTECTIVE CRYSTAL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH ISAC CODING IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 BHMGG 04SIZE,CONNECTION CONNECTION SIZE DESIGNATES THE SIZE OF THE CONNECTION PROVIDED. FULL TEXT WRITE-IN 0 BHMHD 08LOCATION,CONNECTION,MOUNTING MOUNTING CONNECTION LOCATION INDICATES THE MOUNTING CONNECTION LOCATION. SELECT REPLY CODE 10AJ91 BHMJD 08LOCATION,STUD STUD LOCATION INDICATES THAT PORTION OF AN ITEM ON WHICH THE STUD IS LOCATED. SELECT REPLY CODE 10AJ91 BHMKD /D/ 07VENT,TYPE,CONNECTOR CONNECTOR TYPE VENT AN INDICATION OF WHETHER OR NOT A CONNECTOR TYPE VENT IS PROVIDED. SELECT REPLY CODE 10AB22 BHMLG /D/ 10AMOUNT,IMMERSION IMMERSION AMOUNT AN INDICATION OF THE AMOUNT OF IMMERSION REQUIRED FOR THE ITEM. FULL TEXT WRITE-IN 0 BHMMD /D/ 07FEATURE,ELIMINATING,PARALLAX PARALLAX ELIMINATING FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE FOR ELIMINATING PARALLAX IS PROVIDED. SELECT REPLY CODE 10AB22 BHMND /D/ 19LIQUID FOR WHICH DESIGNED,INDICATING INDICATING LIQUID FOR WHICH DESIGNED THE INDICATING LIQUID FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AB75 BHMPD /D/ 07LIQUID,INDICATING INDICATING LIQUID AN INDICATION OF WHETHER OR NOT INDICATING LIQUID IS PROVIDED. SELECT REPLY CODE 10AB22 BHMQD /D/ 07VALVE,CONTROL CONTROL VALVE AN INDICATION OF WHETHER OR NOT A CONTROL VALVE IS PROVIDED. SELECT REPLY CODE 10AB22 BHMRD /D/ 07VALVE,EQUALIZING EQUALIZING VALVE AN INDICATION OF WHETHER OR NOT AN EQUALIZING VALVE IS PROVIDED. SELECT REPLY CODE 10AB22 BHMSD 19PROVISION FOR WHICH DESIGNED,MOUNTING MOUNTING PROVISION FOR WHICH DESIGNED AN INDICATION OF THE MOUNTING PROVISION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AM39 BHMTJ /D/ 10FORCE,MAGNETIC MAGNETIC FORCE THE MAGNETIC FORCE MEASURED AT A SPECIFIED DISTANCE. 2D AND 1B MODE REPLY23AK092AK70 BHMWJ T10RANGE,MEASUREMENT MEASUREMENT RANGE THE MINIMUM TO MAXIMUM VALUE WHICH THE ITEM IS CAPABLE OF MEASURING. 1D AND 1F MODE REPLY12AJ20 BHMXB /D/ 10RATING IN DEG CELSIUS,ACCURACY ACCURACY RATING IN DEG CELSIUS THE ACCURACY FOR WHICH THE ITEM IS RATED, EXPRESSED IN DEGREES CELSIUS. 1B MODE REPLY 0 BHMYH /D/ 19MARKING AND COLOR,SCALE,LUMINOUS LUMINOUS SCALE MARKING AND COLOR AN INDICATION OF THE LUMINOUS SCALE MARKING/S/ AND ITS COLOR. 3D MODE REPLY 33AJ651AB546AD06 BHMZD /D/ 09MATERIAL,DEVICE,ROTATING ROTATING DEVICE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ROTATING DEVICE IS FABRICTED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BHNBJ /D/T10RANGE,FREQUENCY,IMPEDANCE MEASUREMENT IMPEDANCE MEASUREMENT FREQUENCY RANGE THE FREQUENCY RANGE OF THE ITEM FOR EACH IMPEDANCE MEASUREMENT. 1D AND 1F MODE REPLY11AC32 BHNCJ 04DIAMETER,DEVICE,ROTATING ROTATING DEVICE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A ROTATING DEVICE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BHNDJ 04WIDTH,FACE,ROTATING DEVICE ROTATING DEVICE FACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ROTATING DEVICE FACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BHNFJ /D/ 10DC SOURCE AND VOLTAGE IN VOLTS,OPERATING OPERATING DC SOURCE AND VOLTAGE IN VOLTS THE DIRECT CURRENT SOURCE AND THE VOLTAGE REQUIRED TO OPERATE THE ITEM,EXPRESSED IN VOLTS. 2D AND 1B MODE REPLY21AC202AG27 BHNGJ /D/ 10FREQUENCY,OSCILLATOR,INTERNAL INTERNAL OSCILLATOR FREQUENCY THE FREQUENCY OF THE INTERNAL OSCILLATOR. 2D AND 1B MODE REPLY21AC321AC20 BHNHJ /D/T10RANGE,MEASUREMENT,CAPACITANCE CAPACITANCE MEASUREMENT RANGE THE CAPACITANCE RANGE THAT THE ITEM IS DESIGNED TO MEASURE. 1D AND 1F MODE REPLY12AB49 BHNJJ /D/T10RANGE,FREQUENCY,CAPACITANCE MEASUREMENT CAPACITANCE MEASUREMENT FREQUENCY RANGE THE FREQUENCY RANGE OF THE ITEM FOR EACH CAPACITANCE MEASUREMENT. 1D AND 1F MODE REPLY11AC32 BHNKF /D/T10ACCURACY RATING IN PERCENT,MEASUREMENT,CAPACITANCE CAPACITANCE MEASUREMENT ACCURACY RATING IN PERCENT THE ACCURACY RATING OF THE CAPACITANCE MEASUREMENT,EXPRESSED IN PERCENT. 1F MODE REPLY 0 BHNLF /D/T10RANGE IN PERCENT,FACTOR,DISSIPATION DISSIPATION FACTOR RANGE IN PERCENT THE RANGE OF DISSIPATION FACTOR FOR WHICH THE ITEM IS DESIGNED,EXPRESSED IN PERCENT. 1F MODE REPLY 0 BHNMJ /D/ 10VOLTAGE IN VOLTS,TEST,MAXIMUM DC LEAKAGE MAXIMUM DC LEAKAGE TEST VOLTAGE IN VOLTS THE MAXIMUM DIRECT CURRENT VOLTAGE THAT THE ITEM IS CAPABLE OF APPLYING TO AN ITEM BEING TESTED TO DETERMINE ITS LEAKAGE VALUE,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY13AL41 BHNNJ /D/T10RANGE,MEASUREMENT,IMPEDANCE IMPEDANCE MEASUREMENT RANGE THE IMPEDANCE RANGE THAT THE ITEM IS DESIGNED TO MEASURE. 1D AND 1F MODE REPLY11AA57 BHNPD 14SHAPE,DEVICE,ROTATING ROTATING DEVICE SHAPE THE PHYSICAL CONFIGURATION OF THE ROTATING DEVICE. SELECT REPLY CODE 10AD07 BHNQF /D/T10ACCURACY RATING IN PERCENT,MEASUREMENT,IMPEDANCE IMPEDANCE MEASUREMENT ACCURACY RATING IN PERCENT THE ACCURACY RATING OF THE IMPEDANCE MEASUREMENT,EXPRESSED IN PERCENT. 1F MODE REPLY 0 BHNRJ /D/T10RANGE,MEASUREMENT,INDUCTANCE INDUCTANCE MEASUREMENT RANGE THE INDUCTANCE RANGE THAT THE ITEM IS DESIGNED TO MEASURE. 1D AND 1F MODE REPLY12AB49 BHNSJ /D/T10RANGE,FREQUENCY,INDUCTANCE MEASUREMENT INDUCTANCE MEASUREMENT FREQUENCY RANGE THE FREQUENCY RANGE OF THE ITEM FOR EACH INDUCTANCE MEASUREMENT. 1D AND 1F MODE REPLY11AC32 BHNTF /D/T10ACCURACY RATING IN PERCENT,MEASUREMENT,INDUCTANCE INDUCTANCE MEASUREMENT ACCURACY RATING IN PERCENT THE ACCURACY RATING OF THE INDUCTANCE MEASUREMENT,EXPRESSED IN PERCENT. 1F MODE REPLY 0 BHNWJ /D/T10RANGE,MEASUREMENT,RESISTANCE RESISTANCE MEASUREMENT RANGE THE RESISTANCE RANGE THAT THE ITEM IS DESIGNED TO MEASURE. 1D AND 1F MODE REPLY11AA57 BHNXJ /D/T10RANGE,FREQUENCY,RESISTANCE MEASUREMENT RESISTANCE MEASUREMENT FREQUENCY RANGE THE FREQUENCY RANGE OF THE ITEM FOR EACH RESISTANCE MEASUREMENT. 1D AND 1F MODE REPLY11AC32 BHNYF /D/T10ACCURACY RATING IN PERCENT,MEASUREMENT,RESISTANCE RESISTANCE MEASUREMENT ACCURACY RATING IN PERCENT THE ACCURACY RATING OF THE RESISTANCE MEASUREMENT,EXPRESSED IN PERCENT. 1F MODE REPLY 0 BHNZJ /D/T10RANGE,MEASUREMENT,VOLTAGE VOLTAGE MEASUREMENT RANGE THE VOLTAGE RANGE THAT THE ITEM IS DESIGNED TO MEASURE. 1D AND 1F MODE REPLY13AJ40 BHPBJ /D/T10RANGE,FREQUENCY,VOLTAGE MEASUREMENT VOLTAGE MEASUREMENT FREQUENCY RANGE THE FREQUENCY RANGE OF THE ITEM FOR EACH VOLTAGE MEASUREMENT. 1D AND 1F MODE REPLY11AC32 BHPCF /D/T10ACCURACY RATING IN PERCENT,MEASUREMENT,VOLTAGE VOLTAGE MEASUREMENT ACCURACY RATING IN PERCENT THE ACCURACY RATING OF THE VOLTAGE MEASUREMENT,EXPRESSED IN PERCENT. 1F MODE REPLY 0 BHPDF /D/T10RANGE,MEASUREMENT,RESISTANCE RATIO RESISTANCE RATIO MEASUREMENT RANGE THE RESISTANCE RATIO RANGE THAT THE ITEM IS DESIGNED TO MEASURE. 1F MODE REPLY 0 BHPFF /D/T10RANGE,MEASUREMENT,VOLTAGE RATIO VOLTAGE RATIO MEASUREMENT RANGE THE VOLTAGE RATIO RANGE THAT THE ITEM IS DESIGNED TO MEASURE. 1F MODE REPLY 0 BHPGD /D/ 11METHOD,ADJUSTMENT,BALANCE BALANCE ADJUSTMENT METHOD THE MEANS BY WHICH THE BALANCE IS ADJUSTED. SELECT REPLY CODE 10AL41 BHPHD 18TYPE,INCLOSURE,STEAM STEAM INCLOSURE TYPE INDICATES THE TYPE OF STEAM INCLOSURE PROVIDED. SELECT REPLY CODE 10AG85 BHPJJ 04DIAMETER,CONTAINER,INNER INNER CONTAINER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN INNER CONTAINER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BHPKJ 04DEPTH,CONTAINER,INNER INNER CONTAINER DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE INNER CONTAINER,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BHPLD /D/ 19SYSTEM FOR WHICH DESIGNED,SUPPLY,STEAM STEAM SUPPLY SYSTEM FOR WHICH DESIGNED INDICATES THE TYPE OF STEAM SUPPLY SYSTEM FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BHPMD /D/ 09MATERIAL,SHELL,EXTERIOR EXTERIOR SHELL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE EXTERIOR SHELL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BHPND /D/ 17SURFACE TREATMENT,SHELL,EXTERIOR EXTERIOR SHELL SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE EXTERIOR SHELL SURFACE. SELECT REPLY CODE 10AD09 BHPPD /D/ 07COMPARTMENT,LINED LINED COMPARTMENT AN INDICATION OF WHETHER OR NOT A LINED COMPARTMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BHPQD /D/ 17SURFACE TREATMENT,LINING LINING SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING APPLIED TO THE LINING SURFACE THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A SURFACE. SELECT REPLY CODE 10AD09 BHPRJ 04HEIGHT,INSIDE,NOMINAL NOMINAL INSIDE HEIGHT A NOMINAL INSIDE MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN OBJECT,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BHPSJ 04WIDTH,INSIDE,NOMINAL NOMINAL INSIDE WIDTH A NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE INSIDE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BHPTJ 04DEPTH,INSIDE,NOMINAL NOMINAL INSIDE DEPTH A NOMINAL INSIDE MEASUREMENT BETWEEN SPECIFIED POINTS ON AN ITEM,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 BHPWA 12QUANTITY,BASKET,STEAMING STEAMING BASKET QUANTITY THE NUMBER OF STEAMING BASKET(S) INCLUDED. 1A MODE REPLY 0 BHPXD /D/ 07LATCH,SAFETY,PRESSURE RELEASE PRESSURE RELEASE SAFETY LATCH AN INDICATION OF WHETHER OR NOT A PRESSURE RELEASE SAFETY LATCH IS INCLUDED. SELECT REPLY CODE 10AA49 BHPYJ A19CAPACITY,SLICE,TOASTING TOASTING SLICE CAPACITY THE NUMBER OF SLICE(S) THAT THE ITEM WILL TOAST. 2D AND 1A MODE REPLY22AG671AC20 BHPZD 18TYPE,CURRENT,CONVEYOR MOTOR CONVEYOR MOTOR CURRENT TYPE INDICATES THE CURRENT TYPE OF A CONVEYOR MOTOR. SELECT REPLY CODE 10AB62 BHQBJ 10VOLTAGE RATING,MOTOR,CONVEYOR CONVEYOR MOTOR VOLTAGE RATING THE VALUE(S) OF POTENTIAL FOR WHICH THE CONVEYOR MOTOR IS RATED. 2D AND 1B MODE REPLY21AB631AC20 BHQCJ 10FREQUENCY RATING,MOTOR,CONVEYOR CONVEYOR MOTOR FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE CONVEYOR MOTOR IS RATED. 2D AND 1B MODE REPLY21AC321AC20 BHQDJ 10FREQUENCY RATING,MODULATED MODULATED FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE MODULATION IS RATED. 2D AND 1B MODE REPLY21AC321AC20 BHQFJ 10FREQUENCY RATING,REPETITION,PULSE PULSE REPETITION FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE PULSE REPETITION IS RATED. 2D AND 1B MODE REPLY21AC321AC20 BHQGJ 10DEGREE,MODULATION MODULATION DEGREE AN INDICATION OF THE DEGREE OF MODULATION PROVIDED. 2D AND 1B MODE REPLY23AK091AC20 BHQHA 12QUANTITY,RECTIFIER RECTIFIER QUANTITY THE NUMBER OF RECTIFIERS PROVIDED. 1A MODE REPLY 0 BHQJD /D/ 09MATERIAL,RECTIFYING RECTIFYING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE RECTIFYING MATERIAL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BHQKA 12QUANTITY,CONNECTION,INDIVIDUAL CIRCUIT INDIVIDUAL CIRCUIT CONNECTION QUANTITY THE NUMBER OF INDIVIDUAL CIRCUIT CONNECTIONS PROVIDED. 1A MODE REPLY 0 BHQLA 12QUANTITY,RECTIFIER,INDIVIDUAL INDIVIDUAL RECTIFIER QUANTITY THE NUMBER OF INDIVIDUAL RECTIFIERS PROVIDED. 1A MODE REPLY 0 BHQMD 18TYPE,RECTIFIER,INDIVIDUAL INDIVIDUAL RECTIFIER TYPE INDICATES THE TYPE OF INDIVIDUAL RECTIFIER PROVIDED. SELECT REPLY CODE 10AK80 BHQND 11METHOD,RECTIFICATION RECTIFICATION METHOD THE MEANS USED TO CHANGE ALTERNATING CURRENT VOLTAGE TO DIRECT CURRENT VOLTAGE. SELECT REPLY CODE 10AK33 BHQPJ 10CURRENT RATING,OUTPUT,MAXIMUM MAXIMUM OUTPUT CURRENT RATING THE MAXIMUM AMOUNT OF OUTPUT CURRENT FOR WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY12AB49 BHQQJ 10VOLTAGE RATING,MAXIMUM,DC OUTPUT DC OUTPUT MAXIMUM VOLTAGE RATING THE MAXIMUM DIRECT CURRENT OUTPUT VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AB632AL71 BHQRG /D/ 19NUMBER,IDENTIFYING,RECTIFIER RECTIFIER IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE RECTIFIER. FULL TEXT WRITE-IN 0 BHQSJ /D/ 10VOLTAGE RATING,OUTPUT,DC DC OUTPUT VOLTAGE RATING THE RATED VALUE OF DIRECT CURRENT OUTPUT THAT CAN BE SUPPLIED BY THE ITEM. 3D AND 1B MODE REPLY31AB631AC202AN17 BHQTJ /D/ 10CURRENT RATING,OUTPUT,DC DC OUTPUT CURRENT RATING THE DIRECT CURRENT OUTPUT FOR WHICH THE ITEM IS RATED. 3D AND 1B MODE REPLY31AC301AC202AN17 BHQUL 16STYLE,TIP,FLANGE,LEFT-SIDE LEFT-SIDE FLANGE TIP STYLE THE STYLE DESIGNATION CORRESPONDING TO THE SHAPE OF THE LEFT-SIDE FLANGE TIP. 1L MODE REPLY 0 BHQVL 16STYLE,TIP,FLANGE,BASE BASE FLANGE TIP STYLE THE STYLE DESIGNATION CORRESPONDING TO THE SHAPE OF THE BASE FLANGE TIP. 1L MODE REPLY 0 BHQWJ /D/ 10VOLTAGE RATING,OUTPUT,AC AC OUTPUT VOLTAGE RATING THE ALTERNATING CURRENT POTENTIAL FOR WHICH THE ITEM IS RATED REFLECTED AT THE OUTPUT OF THE ITEM. 3D AND 1B MODE REPLY31AB631AC202AN17 BHQXJ /D/ 10CURRENT RATING,OUTPUT,AC AC OUTPUT CURRENT RATING THE ALTERNATING CURRENT OUTPUT FOR WHICH THE ITEM IS RATED. 3D AND 1B MODE REPLY31AC301AC202AN17 BHQYG /D/ 19SPEC/STD,TREATMENT,SURFACE SURFACE TREATMENT SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE SURFACE TREATMENT. FULL TEXT WRITE-IN 0 BHQZD /D/ 07TOP,REMOVABLE REMOVABLE TOP AN INDICATION OF WHETHER OR NOT A REMOVABLE TOP IS INCLUDED. PLEASE USE MRC CBBL IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 BHRBD /D/ 07SEAL,TOP TOP SEAL AN INDICATION OF WHETHER OR NOT A TOP SEAL IS INCLUDED. SELECT REPLY CODE 10AA49 BHRCD /D/ 07BRACES,FOLDING,TOP TOP FOLDING BRACES AN INDICATION OF WHETHER OR NOT TOP FOLDING BRACES ARE INCLUDED. SELECT REPLY CODE 10AA49 BHRDD /D/ 07TRAY,INTERNAL INTERNAL TRAY AN INDICATION OF WHETHER OR NOT AN INTERNAL TRAY/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BHRFD /D/ 07PULLS,COVER COVER PULLS AN INDICATION OF WHETHER OR NOT COVER PULLS ARE INCLUDED. SELECT REPLY CODE 10AA49 BHRGD /D/ 18TYPE,SPOUT,POURING,FLEXIBLE FLEXIBLE POURING SPOUT TYPE INDICATES THE TYPE OF FLEXIBLE POURING SPOUT PROVIDED. SELECT REPLY CODE 10AH97 BHRHA 12QUANTITY,CONTAINER,INNER INNER CONTAINER QUANTITY THE NUMBER OF INNER CONTAINERS FURNISHED WITH THE ITEM. 1A MODE REPLY 0 BHRJD /D/ 09MATERIAL,CONTAINER,OUTER OUTER CONTAINER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE OUTER CONTAINER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH ISAC TABLE 0205 IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 BHRKJ 04LENGTH,INSIDE,COIL COIL INSIDE LENGTH A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF A COIL,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BHRLJ 04WIDTH,INSIDE,COIL COIL INSIDE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE INSIDE LENGTH OF A COIL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BHRMD /D/ 09MATERIAL,CONTAINER,INNER INNER CONTAINER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INNER CONTAINER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH ISAC TABLE 0205 IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 BHRNJ 04LENGTH,OVERALL,INNER CONTAINER INNER CONTAINER OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE INNER CONTAINER. 2D AND 1B MODE REPLY21AA051AC20 BHRPJ 04WIDTH,OVERALL,INNER CONTAINER INNER CONTAINER OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN INNER CONTAINER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BHRQJ 04LENGTH,BLOCK,END END BLOCK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE END BLOCK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BHRRJ 04WIDTH,BLOCK,END END BLOCK WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE END BLOCK,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BHRSJ 04HEIGHT,BLOCK,END END BLOCK HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE END BLOCK,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BHRTG 11METHOD,CONSTRUCTION CONSTRUCTION METHOD THE MEANS USED TO CONSTRUCT THE ITEM. FULL TEXT WRITE-IN 0 BHRWJ 04DISTANCE FROM FLOOR TO TOP OF RIM DISTANCE FROM FLOOR TO TOP OF RIM THE DISTANCE FROM THE FLOOR TO THE TOP OF THE RIM. 2D AND 1B MODE REPLY21AA051AC20 BHRXD /D/ 07MECHANISM,LIFTING LIFTING MECHANISM AN INDICATION OF WHETHER OR NOT A LIFTING MECHANISM IS INCLUDED. SELECT REPLY CODE 10AA49 BHRYD 11METHOD,ASSEMBLY,SUPPORT SUPPORT ASSEMBLY METHOD THE MEANS BY WHICH THE SUPPORT IS FASTENED TOGETHER. SELECT REPLY CODE 10AB47 BHRZD 14SHAPE,CROSS-SECTIONAL,SUPPORT MATERIAL SUPPORT MATERIAL CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE SUPPORT MATERIAL WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 BHSBD 19CONSTRUCTION,SUPPORT SUPPORT CONSTRUCTION THE STRUCTURAL CHARACTERISTIC OF THE SUPPORT. SELECT REPLY CODE 10AE33 BHSCD 07ADJUSTABILITY,HEIGHT,SUPPORT SUPPORT HEIGHT ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE SUPPORT HEIGHT IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BHSDD 11METHOD,INSERTION INSERTION METHOD THE MEANS BY WHICH AN ITEM IS INSERTED. SELECT REPLY CODE 10AJ28 BHSFJ A19ITEMS AND QUANTITY,STORAGE STORAGE ITEMS AND QUANTITY THE NAME AND NUMBER OF THOSE ITEMS THAT MAY BE STORED. 1D AND 1A MODE REPLY13AK54 BHSGD /D/ 19NAME FOR WHICH DISPENSER IS DESIGNED,ITEM ITEM NAME FOR WHICH DISPENSER IS DESIGNED THE NAME OF THE ITEM FOR WHICH THE DISPENSER IS DESIGNED. SELECT REPLY CODE 10AK54 BHSHJ 04WIDTH,STOVE STOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BHSJJ 04HEIGHT,STOVE STOVE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BHSKJ 04DEPTH,STOVE STOVE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BHSLJ 04DIAMETER,SUPPORT,POT POT SUPPORT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BHSMJ 04DIAMETER,STOVE STOVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BHSND 05DIRECTION,DRAFT DRAFT DIRECTION THE DIRECTION OF THE AIR FLOW. SELECT REPLY CODE 10AJ69 BHSPA 12QUANTITY,CHAMBER,FLOAT FLOAT CHAMBER QUANTITY THE NUMBER OF FLOAT CHAMBERS PROVIDED. 1A MODE REPLY 0 BHSQD /D/ 18TYPE,FLOAT FLOAT TYPE INDICATES THE TYPE OF FLOAT USED. SELECT REPLY CODE 10AE98 BHSRD 19NAME,SUBASSEMBLY SUBASSEMBLY NAME THE NAME OF THE SUBASSEMBLY WHICH FACILITATES IDENTIFICATION. SELECT REPLY CODE 10AL83 BHSSD /D/ 07FEATURE,MOUNTING,ADAPTER ADAPTER MOUNTING FEATURE AN INDICATION OF WHETHER OR NOT AN ADAPTER MOUNTING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BHSTG /D/ 04SIZE AND QUANTITY,FACILITY,MOUNTING MOUNTING FACILITY SIZE AND QUANTITY DESIGNATES THE MOUNTING FACILITY SIZE AND NUMBER OF EACH. FULL TEXT WRITE-IN 0 BHSWA 12QUANTITY,FLANGE,FUEL OUTLET FUEL OUTLET FLANGE QUANTITY THE NUMBER OF FUEL OUTLET FLANGES PROVIDED. 1A MODE REPLY 0 BHSXD 18TYPE,CONSTRUCTION,CIRCUIT CIRCUIT CONSTRUCTION TYPE INDICATES THE TYPE OF CIRCUIT CONSTRUCTION PROVIDED IN THE ITEM. SELECT REPLY CODE 10AM43 BHSYA 10SWITCHING RATE PER SECOND SWITCHING RATE PER SECOND THE NUMBER OF SWITCHING CYCLES THAT OCCUR PER SECOND. 1A MODE REPLY 0 BHSZJ 10SHIFT,FREQUENCY FREQUENCY SHIFT THE SHIFT OF THE FREQUENCY OF THE ITEM. 1D AND 1B MODE REPLY11AC32 BHTBJ 10FREQUENCY PER CHANNEL FREQUENCY PER CHANNEL THE PORTION OF THE FREQUENCY SPECTRUM AT WHICH AN ITEM IS DESIGNED TO RECEIVE OR TRANSMIT SIGNAL POWER. 3D AND 1B MODE REPLY31AC321AC203AN18 BHTDD 18TYPE,ADJUSTMENT,FREQUENCY FREQUENCY ADJUSTMENT TYPE INDICATES THE TYPE OF FREQUENCY ADJUSTMENT INCLUDED IN THE ITEM. SELECT REPLY CODE 10AD63 BHTFJ 10FREQUENCY,STEP,INDIVIDUAL INDIVIDUAL STEP FREQUENCY THE FREQUENCY OF EACH STEP. 1D AND 1B MODE REPLY11AC32 BHTGB 10FREQUENCY RATING IN DECIBELS,VARIATION VARIATION FREQUENCY RATING IN DECIBELS THE AMOUNT OF ALLOWABLE VARIATION RELATIVE TO A SPECIFIED FREQUENCY LEVEL,EXPRESSED IN DECIBELS. 1B MODE REPLY 0 BHTHB 10ATTENUATION IN DECIBELS ATTENUATION IN DECIBELS THE DECREASE IN STRENGTH OF AN ELECTRICAL IMPULSE,EXPRESSED IN DECIBELS. 1B MODE REPLY 0 BHTJJ 10POWER RATING,AVERAGE PER CHANNEL AVERAGE POWER RATING PER CHANNEL THE RATED AVERAGE POWER FOR EACH CHANNEL. 2D AND 1B MODE REPLY21AC331AC00 BHTKJ 10VOLTAGE RATING PER CHANNEL,SIGNAL SIGNAL VOLTAGE RATING PER CHANNEL THE RATED SIGNAL VOLTAGE FOR EACH CHANNEL. 3D AND 1B MODE REPLY31AB631AC201AC00 BHTLJ 10GAIN,OVERALL OVERALL GAIN THE INCREASE IN ENERGY FROM THE INPUT TO THE OUTPUT. 1D AND 1B MODE REPLY12AB49 BHTNJ 10IMPEDANCE RATING PER CHANNEL IMPEDANCE RATING PER CHANNEL THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) TO THE FLOW OF ALTERNATING CURRENT PER CHANNEL. 2D AND 1B MODE REPLY22AE753AN18 BHTPJ 10DURATION PER CHANNEL,PULSE PULSE DURATION PER CHANNEL THE TIME REQUIRED FOR ONE COMPLETE PULSE PER CHANNEL. 3D AND 1B MODE REPLY32AB491AC203AN18 BHTQJ 10TIME PER CHANNEL,RISE,PULSE PULSE RISE TIME PER CHANNEL THE LENGTH OF TIME IT TAKES THE PULSE TO RISE PER CHANNEL. 3D AND 1B MODE REPLY32AB491AC203AN18 BHTRJ 10TIME PER CHANNEL,DECAY,PULSE PULSE DECAY TIME PER CHANNEL THE LENGTH OF TIME IT TAKES THE TRAILING EDGE OF THE PULSE TO FALL PER CHANNEL. 3D AND 1B MODE REPLY32AB491AC203AN18 BHTSH 19POLARITY PER CHANNEL POLARITY PER CHANNEL AN ELECTRICAL CONDITION DETERMINING THE DIRECTION IN WHICH CURRENT TENDS TO FLOW PER CHANNEL. 2D MODE REPLY 21AK223AN18 BHTTJ 10REPETITION RATE PER CHANNEL,PULSE PULSE REPETITION RATE PER CHANNEL THE AVERAGE RATE AT WHICH THE PULSE(S) RECURS WITHIN A SPECIFIC TIME INTERVAL PER CHANNEL. 3D AND 1B MODE REPLY32AB491AC203AN18 BHTWJ 10AMPLITUDE PER CHANNEL,PEAK,PULSE PULSE PEAK AMPLITUDE PER CHANNEL THE MAXIMUM ABSOLUTE PEAK VALUE OF THE PULSE PER CHANNEL. 2D AND 1B MODE REPLY22AB493AN18 BHTXJ A12QUANTITY PER CHANNEL,CONTENT,PULSE TRAIN PULSE TRAIN CONTENT QUANTITY PER CHANNEL THE NUMBER OF PULSES IN A GROUP PER CHANNEL. 1D AND 1A MODE REPLY13AN18 BHTYH 18TYPE PER CHANNEL,MODULATION,PULSE PULSE MODULATION TYPE PER CHANNEL INDICATES THE TYPE OF PULSE MODULATION PER CHANNEL. 2D MODE REPLY 22AJ523AN18 BHTZH 18TYPE PER CHANNEL,DATA,SIGNAL SIGNAL DATA TYPE PER CHANNEL INDICATES THE TYPE OF SIGNAL DATA PER CHANNEL. 2D MODE REPLY 23AN182AJ52 BHWBA 12QUANTITY,POINT,REFERENCE REFERENCE POINT QUANTITY THE NUMBER OF AVAILABLE REFERENCE POINTS. 1A MODE REPLY 0 BHWCD 01COLOR,TOP TOP COLOR THE HUE OR TINT OF THE TOP OF THE ITEM. SELECT REPLY CODE 10AD06 BHWDD 08LOCATION,DRAWER DRAWER LOCATION INDICATES THE LOCATION OF THE DRAWER ON THE ITEM. SELECT REPLY CODE 10AJ91 BHWFD 08LOCATION,SLIDE,PULLOUT PULLOUT SLIDE LOCATION INDICATES THE LOCATION OF THE PULLOUT SLIDE OF THE ITEM. SELECT REPLY CODE 10AJ91 BHWGD 08LOCATION,DROPLEAF DROPLEAF LOCATION INDICATES THE LOCATION OF THE DROPLEAF ON THE ITEM. SELECT REPLY CODE 10AJ91 BHWHD 01COLOR,FRAME FRAME COLOR THE HUE OR TINT OF THE FRAME. SELECT REPLY CODE 10AD06 BHWJD /D/ 09MATERIAL,LEAF LEAF MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LEAF IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BHWKD /D/ 07SHELF,BOOK,ADDITIONAL ADDITIONAL BOOK SHELF AN INDICATION OF WHETHER OR NOT AN ADDITIONAL BOOK SHELF(VES) IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BHWLD /D/ 07TOP,SLANTING SLANTING TOP AN INDICATION OF WHETHER OR NOT A SLANTING TOP(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BHWMA 12QUANTITY,SHELF,PULLOUT PULLOUT SHELF QUANTITY THE NUMBER OF PULLOUT SHELVES PROVIDED WITH THE ITEM. 1A MODE REPLY 0 BHWNJ A18TYPE AND QUANTITY,RECEPTACLE,BOOK BOOK RECEPTACLE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF BOOK RECEPTACLES PROVIDED. 1D AND 1A MODE REPLY13AM39 BHWPD /D/ 07REMOVABILITY,BOARD,BULLETIN BULLETIN BOARD REMOVABILITY AN INDICATION OF WHETHER OR NOT A BULLETIN BOARD(S) IS REMOVABLE. SELECT REPLY CODE 10AC29 BHWQD /D/ 09MATERIAL,TOP,DESK DESK TOP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE DESK TOP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BHWRD /D/ 09MATERIAL,COMPARTMENT,BOOK BOOK COMPARTMENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BOOK COMPARTMENT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BHWSH /D/ 11METHOD AND MATERIAL,SUPPORT,DESK DESK SUPPORT METHOD AND MATERIAL THE MEANS PROVIDED FOR SUPPORTING THE DESK AND THE MATERIAL. 2D MODE REPLY 23AM396AD09 BHWTD /D/ 09MATERIAL,FRAME,CHAIR CHAIR FRAME MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CHAIR FRAME IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BHWWG 04SIZE,TOP,DESK DESK TOP SIZE DESIGNATES THE SIZE OF THE DESK TOP. FULL TEXT WRITE-IN 0 BHWXJ /D/ 04HEIGHT,DESK DESK HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE DESK,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BHWYJ 04HEIGHT,SEAT SEAT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE SEAT,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BHWZD /D/ 07CHAIR,SWIVEL SWIVEL CHAIR AN INDICATION OF WHETHER OR NOT A SWIVEL CHAIR(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BHXBD 07ADJUSTABILITY,SURFACE,WRITING WRITING SURFACE ADJUSTABILITY AN INDICATION OF WHETHER OR NOT A WRITING SURFACE(S) IS ADJUSTABLE. SELECT REPLY CODE 10AC06 BHXCD /D/ 19POSITION,ADJUSTMENT ADJUSTMENT POSITION AN INDICATION OF THE POSITION(S) TO WHICH THE ITEM CAN BE ADJUSTED. SELECT REPLY CODE 10AF63 BHXDD /D/ 09MATERIAL,COVERING,TOP TOP COVERING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE COVERING OF THE TOP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BHXFD 01COLOR,COVERING COVERING COLOR THE HUE OR TINT OF THE COVERING. SELECT REPLY CODE 10AD06 BHXGJ A18TYPE AND QUANTITY,SUPPORT SUPPORT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF SUPPORTS. 1D AND 1A MODE REPLY13AA78 BHXHD /D/ 09MATERIAL,BACK,CHAIR CHAIR BACK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CHAIR BACK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BHXJD /D/ 09MATERIAL,SEAT,CHAIR CHAIR SEAT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CHAIR SEAT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BHXKH /D/ 11METHOD AND MATERIAL,SUPPORT,CHAIR CHAIR SUPPORT METHOD AND MATERIAL THE MEANS PROVIDED FOR SUPPORTING THE CHAIR AND THE MATERIAL. 2D MODE REPLY 23AM396AD09 BHXLD /D/ 07FRONT,BEADED BEADED FRONT AN INDICATION OF WHETHER OR NOT A BEADED FRONT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BHXMF T10ACCURACY IN PERCENT,MEASUREMENT,FREQUENCY FREQUENCY MEASUREMENT ACCURACY IN PERCENT AN INDICATION OF THE MEASUREMENT ACCURACY OF THE FREQUENCY,EXPRESSED IN PERCENT. 1F MODE REPLY 0 BHXNJ T10RANGE,TEMP,OPERATING,FREQUENCY MEASUREMENT FREQUENCY MEASUREMENT OPERATING TEMP RANGE THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH THE FREQUENCY MEASUREMENT IS DESIGNED TO OPERATE. 1D AND 1F MODE REPLY11AB36 BHXPD 08LOCATION,PULSE,INPUT INPUT PULSE LOCATION INDICATES THE LOCATION OF THE INPUT PULSE. SELECT REPLY CODE 10AJ91 BHXQD 18TYPE,POLARITY,INPUT PULSE INPUT PULSE POLARITY TYPE INDICATES THE TYPE OF POLARITY OF THE INPUT PULSE. SELECT REPLY CODE 10AK74 BHXRJ 10VOLTAGE RATING,PULSE,INPUT INPUT PULSE VOLTAGE RATING THE VALUE,OR RANGE OF VALUES,FOR WHICH THE INPUT PULSE IS RATED. 2D AND 1B MODE REPLY21AB631AC20 BHXSD 18TYPE,POLARITY,OUTPUT OUTPUT POLARITY TYPE INDICATES THE TYPE OF OUTPUT POLARITY OF THE ITEM. SELECT REPLY CODE 10AK74 BHXTD 18TYPE,MARKER MARKER TYPE INDICATES THE TYPE OF MARKER PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AJ12 BHXWJ 10RANGE,FREQUENCY,MARKER PULSE RECURRENCE MARKER PULSE RECURRENCE FREQUENCY RANGE THE RANGE OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE MARKER PULSE RECURRENCE IS RATED. 2D AND 1B MODE REPLY21AC321AC20 BHXXD 11METHOD,PRODUCTION,ELECTROMOTIVE FORCE ELECTROMOTIVE FORCE PRODUCTION METHOD THE MEANS BY WHICH THE NECESSARY VOLTAGE OR ELECTRIC PRESSURE REQUIRED TO CAUSE A FLOW OF ELECTRICITY MAY BE OBTAINED. SELECT REPLY CODE 10AA62 BHXYD 18TYPE,ELECTROLYTE ELECTROLYTE TYPE INDICATES THE TYPE OF ELECTROLYTE PROVIDED. SELECT REPLY CODE 10AL79 BHXZF T10ACCURACY RATING IN PERCENT,OUTPUT OUTPUT ACCURACY RATING IN PERCENT A MEASUREMENT OF THE OUTPUT ACCURACY OF THE ITEM,EXPRESSED IN PERCENT. 1F MODE REPLY 0 BHYBB 10TIME FOR MAXIMUM ACCURACY IN MINUTES,WARM-UP WARM-UP TIME FOR MAXIMUM ACCURACY IN MINUTES THE WARM-UP TIME TO OBTAIN MAXIMUM ACCURACY,EXPRESSED IN MINUTES. 1B MODE REPLY 0 BHYCD 18TYPE,DEVICE,PROTECTIVE PROTECTIVE DEVICE TYPE INDICATES THE TYPE OF PROTECTIVE DEVICE PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AH83 BHYDJ 10RESISTANCE,RESISTOR,SERIES SERIES RESISTOR RESISTANCE AN INDICATION OF THE RESISTANCE OF THE SERIES RESISTOR. 2D AND 1B MODE REPLY21AA571AC20 BHYFJ 10VOLTAGE RATING,PEAK,MAXIMUM MAXIMUM PEAK VOLTAGE RATING THE MAXIMUM INSTANTANEOUS VOLTAGE FOR WHICH AN ITEM IS RATED. 2D AND 1B MODE REPLY21AB621AB63 BHYGJ 10FREQUENCY,LIMITING LIMITING FREQUENCY THE FREQUENCY AT WHICH THERE IS A RECOGNIZABLE CHANGE IN RESPONSE FOR WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY11AC32 BHYHG /D/ 10COEFFICIENT,TEMP TEMP COEFFICIENT THE AMOUNT OF CHANGE IN THE VALUE OF PERFORMANCE CHARACTERISTIC PER DEGREE CHANGE IN TEMPERATURE. FULL TEXT WRITE-IN 0 BHYJG /D/ 04SIZE,HOLE/STUD,MOUNTING MOUNTING HOLE/STUD SIZE DESIGNATES THE SIZE OF THE HOLE AND/OR STUD FOR MOUNTING THE ITEM. FULL TEXT WRITE-IN 0 BHYKD /D/ 07PROBE PROBE AN INDICATION OF WHETHER OR NOT A PROBE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BHYLD /D/ 07INDICATOR,GAGE,DIAL DIAL GAGE INDICATOR AN INDICATION OF WHETHER OR NOT A DIAL GAGE INDICATOR(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BHYMJ T10RANGE,SCALE,VERNIER VERNIER SCALE RANGE AN INDICATION OF THE MINIMUM AND MAXIMUM LIMITS OF THE VERNIER SCALE. 1D AND 1F MODE REPLY11AA05 BHYNJ 10RESOLUTION,MEASUREMENT,VERNIER SCALE VERNIER SCALE MEASUREMENT RESOLUTION THE RESOLVED MEASUREMENT OF A VERNIER SCALE. 1D AND 1B MODE REPLY11AA05 BHYPJ T10RANGE,INDICATOR,DIAL GAGE DIAL GAGE INDICATOR RANGE THE MINIMUM AND MAXIMUM VALUES FOR WHICH THE DIAL GAGE INDICATOR IS RATED. 1D AND 1F MODE REPLY11AA05 BHYQJ 10RESOLUTION,MEASUREMENT,DIAL GAGE INDICATOR DIAL GAGE INDICATOR MEASUREMENT RESOLUTION THE RESOLVED MEASUREMENT FOR WHICH THE DIAL GAGE INDICATOR IS RATED. 1D AND 1B MODE REPLY11AA05 BHYRG 19NAME,TERMINATION TERMINATION NAME THE NAME OF THE TERMINATION AS ASSIGNED BY THE CONTROLLING AGENCY. FULL TEXT WRITE-IN 0 BHYSJ A19NUMBER,IDENTIFYING,TERMINATION TERMINATION IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE TERMINATION. 1D AND 1A MODE REPLY12AG99 BHYTD 18TYPE FOR WHICH DESIGNED,CONDUCTOR CONDUCTOR TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF CONDUCTOR FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL01 BHYWJ 04LENGTH,INSERTION INSERTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE INSERTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BHYXD 07ADJUSTABILITY,ELIMINATION,SLOPE ERROR SLOPE ERROR ELIMINATION ADJUSTABILITY AN INDICATION OF WHETHER OR NOT A SLOPE ERROR ELIMINATION(S) IS ADJUSTABLE. SELECT REPLY CODE 10AC06 BHYYG 19MARKING,UNIT,SCALE MEASUREMENT SCALE MEASUREMENT UNIT MARKING INDICATES THE TYPE OF MARKING PROVIDED ON THE SCALE MEASUREMENT UNIT. FULL TEXT WRITE-IN 0 BHYZD /D/ 09MATERIAL,SCALE SCALE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SCALE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 BHZBB /D/ 10VOLTAGE IN MILLIVOLTS VOLTAGE IN MILLIVOLTS THE TOTAL ELECTRICAL VOLTAGE,EXPRESSED IN MILLIVOLTS. 1B MODE REPLY 0 BHZDA 12QUANTITY,SHELF,SIDE,STATIONARY STATIONARY SIDE SHELF QUANTITY THE NUMBER OF STATIONARY SIDE SHELF(VES) ON THE ITEM. 1A MODE REPLY 0 BHZFD /D/ 07FEATURE,CONSTRUCTION,KNOCKDOWN KNOCKDOWN CONSTRUCTION FEATURE AN INDICATION OF WHETHER OR NOT A KNOCKDOWN CONSTRUCTION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BHZGJ 10UNIT FREQUENCY,INDIVIDUAL PLUG-IN INDIVIDUAL PLUG-IN UNIT FREQUENCY THE CYCLES PER SECOND OF THE ALTERNATING CURRENT FOR WHICH THE INDIVIDUAL PLUG-IN UNIT IS RATED. 1D AND 1B MODE REPLY11AC32 BHZHG /D/ 10RANGE,SCALE,METER METER SCALE RANGE AN INDICATION OF THE MINIMUM TO MAXIMUM SCALE OF THE METER. FULL TEXT WRITE-IN 0 BHZJF T10RANGE IN PERCENT,ACCURACY,METER METER ACCURACY RANGE IN PERCENT THE ACCEPTABLE LIMITS OF DEVIATION FROM THE DESIGNED STANDARD OUTPUT VALUE OF THE METER,EXPRESSED IN PERCENT. 1F MODE REPLY 0 BHZKG 19INFORMATION,DISPLAYED,CATHODE RAY TUBE CATHODE RAY TUBE DISPLAYED INFORMATION THE INFORMATION DISPLAYED ON THE CATHODE RAY TUBE. FULL TEXT WRITE-IN 0 BHZLD /D/ 07ACCOMMODATION,DEVICE,RECORDING RECORDING DEVICE ACCOMMODATION AN INDICATION OF WHETHER OR NOT A RECORDING DEVICE ACCOMMODATION/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 BHZMD 18TYPE,STOCK STOCK TYPE INDICATES THE TYPE OF STOCK PROVIDED. SELECT REPLY CODE 10AK54 BHZNJ A18TYPE AND QUANTITY,FILM,PROCESSED PROCESSED FILM TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF PROCESSED FILM. 1D AND 1A MODE REPLY12AG37 BHZPA 19YEAR,RELEASE RELEASE YEAR AN INDICATION OF THE YEAR THE ITEM WAS RELEASED. 1A MODE REPLY 0 BHZQD 18TYPE,FILM,MOTION PICTURE MOTION PICTURE FILM TYPE INDICATES THE TYPE OF MOTION PICTURE FILM PROVIDED. SELECT REPLY CODE 10AG37 BHZRD /D/ 07FILM FILM AN INDICATION OF WHETHER OR NOT A FILM IS INCLUDED. SELECT REPLY CODE 10AA49 BHZSD /D/ 07COMPENSATION,MOTION,IMAGE IMAGE MOTION COMPENSATION AN INDICATION OF WHETHER OR NOT THE MEANS FOR IMAGE MOTION COMPENSATION IS INCLUDED. SELECT REPLY CODE 10AA49 BHZTD 04SIZE,FORMAT FORMAT SIZE DESIGNATES THE SIZE OF THE FORMAT. SELECT REPLY CODE 10AF81 BHZWD /D/ 07CONTROL,CUTOFF,AUTOMATIC AUTOMATIC CUTOFF CONTROL AN INDICATION OF WHETHER OR NOT AN AUTOMATIC CUTOFF CONTROL(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BHZXD /D/ 07SWITCH,FILM,AUTOMATIC END AUTOMATIC END FILM SWITCH AN INDICATION OF WHETHER OR NOT AN AUTOMATIC END OF FILM SWITCH(ES) IS INCLUDED. SELECT REPLY CODE 10AA49 BHZYG 04SIZE ACCOMMODATED,FILM FILM SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE FILM THE ITEM IS DESIGNED TO ACCOMMODATE. FULL TEXT WRITE-IN 0 BHZZD /D/ 07FEATURE,NESTING,SLOPING SIDE SLOPING SIDE NESTING FEATURE AN INDICATION OF WHETHER OR NOT A NESTING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BJBBJ 10CIRCULATION RATE,WATER,MINIMUM MINIMUM WATER CIRCULATION RATE THE MINIMUM RATE AT WHICH THE ITEM CAN CIRCULATE WATER. 1D AND 1B MODE REPLY12AG67 BJBCJ 10VALUE,POINT,REFERENCE REFERENCE POINT VALUE THE VALUE REPRESENTED BY THE GENERATED REFERENCE POINTS. 1D AND 1B MODE REPLY12AB49 BJBDD /D/ 07CAPABILITY,SHIFT,ZERO ZERO SHIFT CAPABILITY AN INDICATION OF WHETHER OR NOT A ZERO SHIFT CAPABILITY IS INCLUDED. SELECT REPLY CODE 10AA49 BJBFA 12QUANTITY,POINT,REFERENCE,INTENSIFIED INTENSIFIED REFERENCE POINT QUANTITY THE NUMBER OF REFERENCE POINTS THAT ARE INTENSIFIED. 1A MODE REPLY 0 BJBGJ 18TYPE AND PERCENT,DISTORTION DISTORTION TYPE AND PERCENT INDICATES THE TYPE OF DISTORTION AND ITS PERCENT. 1D AND 1B MODE REPLY12AJ52 BJBHF T10TOLERANCE IN PERCENT,CALIBRATED CALIBRATED TOLERANCE IN PERCENT THE LIMITS OF CALBRATION,EXPRESSED IN PERCENT. 1F MODE REPLY 0 BJBJD 14SHAPE,WAVE,OUTPUT OUTPUT WAVE SHAPE THE PHYSICAL CONFIGURATION OF THE OUTPUT WAVE. SELECT REPLY CODE 10AD07 BJBKD 19PATTERN,INTERFERENCE INTERFERENCE PATTERN AN INDICATION OF THE INTERFERENCE PATTERN OF THE ITEM. SELECT REPLY CODE 10AN19 BJBLJ A18TYPE AND QUANTITY,DEVICE,INDICATOR INDICATOR DEVICE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF INDICATOR DEVICE(S) INCLUDED. 1D AND 1A MODE REPLY13AJ12 BJBMB 10TIME IN HOURS,CONTINUOUS OPERATING,MAXIMUM MAXIMUM CONTINUOUS OPERATING TIME IN HOURS THE MAXIMUM TIME AN ITEM WILL CONTINUOUSLY RUN,EXPRESSED IN HOURS. 1B MODE REPLY 0 BJBNJ 10TIME,DURATION,SHOCK PULSE SHOCK PULSE DURATION TIME THE LENGTH OF TIME AFTER IMPACT THAT ESTABLISHED THE CONDITION AT WHICH THE SHOCK RESISTANCE RATING APPLIES. 1D AND 1B MODE REPLY12AB49 BJBPH 18TYPE AND LOCATION,CONNECTION CONNECTION TYPE AND LOCATION INDICATES THE TYPE OF CONNECTION AND ITS LOCATION ON THE ITEM. 2D MODE REPLY 22AB763AJ91 BJBQJ 10FREQUENCY IN HERTZ,AC,OPERATING OPERATING AC FREQUENCY IN HERTZ THE CYCLES PER SECOND /HERTZ/ OF THE OPERATING ALTERNATING CURRENT. 2D AND 1B MODE REPLY21AC202AD88 BJBRJ 10DRAIN RATING,POWER,MAXIMUM MAXIMUM POWER DRAIN RATING THE MAXIMUM POWER DRAIN FOR WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY12AB49 BJBSD 19FUNCTION,CALIBRATION CALIBRATION FUNCTION A DESIGNATION OF THE FUNCTION WHICH IS CALIBRATED. SELECT REPLY CODE 10AJ52 BJBTJ 10PRESSURE RATING,CONNECTION,MAXIMUM MAXIMUM CONNECTION PRESSURE RATING THE MAXIMUM RATED PRESSURE THAT A CONNECTION CAN WITHSTAND WITHOUT RUPTURE. 2D AND 1B MODE REPLY21AB182AB76 BJBWJ A18TYPE AND QUANTITY,CONTACT,CONNECTION CONNECTION CONTACT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF CONTACT(S) INCLUDED IN THE CONNECTION. 2D AND 1A MODE REPLY22AB762AG81 BJBXD 14SHAPE,FLANGE,FUEL OUTLET FUEL OUTLET FLANGE SHAPE THE PHYSICAL CONFIGURATION OF THE FUEL OUTLET FLANGE. SELECT REPLY CODE 10AD07 BJBYG /D/ 04SIZE,FLANGE,FUEL OUTLET FUEL OUTLET FLANGE SIZE DESIGNATES THE SIZE OF THE FUEL OUTLET FLANGE. FULL TEXT WRITE-IN 0 BJBZD 14SHAPE,INLET,AIR AIR INLET SHAPE THE PHYSICAL CONFIGURATION OF THE AIR INLET. SELECT REPLY CODE 10AD07 BJCBG /D/ 19ARRANGEMENT,STOWAGE,BULK BULK STOWAGE ARRANGEMENT THE ARRANGEMENT(S) FOR WHICH THE BULK STOWAGE MAY PROVIDE. FULL TEXT WRITE-IN 0 BJCCJ 04DIAMETER,OUTSIDE,AIR INLET AIR INLET OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN AIR INLET,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BJCDD 14SHAPE,FLANGE,AIR INLET AIR INLET FLANGE SHAPE THE PHYSICAL CONFIGURATION OF THE AIR INLET FLANGE. SELECT REPLY CODE 10AD07 BJCFG 04SIZE,FLANGE,AIR INLET AIR INLET FLANGE SIZE DESIGNATES THE SIZE OF THE AIR INLET FLANGE. FULL TEXT WRITE-IN 0 BJCGA 12QUANTITY,HOLE,MOUNTING,AIR INLET FLANGE AIR INLET FLANGE MOUNTING HOLE QUANTITY THE NUMBER OF MOUNTING HOLES PROVIDED IN THE AIR INLET FLANGE. 1A MODE REPLY 0 BJCHJ 04DIAMETER,HOLE,MOUNTING,AIR INLET FLANGE AIR INLET FLANGE MOUNTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN AIR INLET FLANGE MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BJCJG /D/ 04SPACING,HOLE,AIR INLET FLANGE MOUNTING AIR INLET FLANGE MOUNTING HOLE SPACING THE MEASURED DISTANCE BETWEEN THE AIR INLET FLANGE MOUNTING HOLES. FULL TEXT WRITE-IN 0 BJCKD /D/ 07PROVISION,THREAD,AIR INLET FLANGE MOUNTING HOLE AIR INLET FLANGE MOUNTING HOLE THREAD PROVISION AN INDICATION OF WHETHER OR NOT THREADS ARE PROVIDED IN THE AIR INLET FLANGE MOUNTING HOLE. SELECT REPLY CODE 10AB22 BJCLA /D/ 13THREAD SIZE,HOLE,MOUNTING,AIR INLET FLANGE AIR INLET FLANGE MOUNTING HOLE THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF AN AIR INLET FLANGE MOUNTING HOLE. 1A MODE REPLY 0 BJCMD 13THREAD SERIES DESIGNATOR,HOLE,MOUNTING,AIR INLET FLANGE AIR INLET FLANGE MOUNTING HOLE THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF AN AIR INLET FLANGE MOUNTING HOLE. SELECT REPLY CODE 10AH06 BJCND 13THREAD DIRECTION,HOLE,MOUNTING,AIR INLET FLANGE AIR INLET FLANGE MOUNTING HOLE THREAD DIRECTION THE DIRECTION OF THE AIR INLET FLANGE MOUNTING HOLE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 BJCPA 13THREAD SIZE,INLET,AIR AIR INLET THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF AN AIR INLET. 1A MODE REPLY 0 BJCQD 13THREAD SERIES DESIGNATOR,INLET,AIR AIR INLET THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF AN AIR INLET. SELECT REPLY CODE 10AH06 BJCRD 13THREAD DIRECTION,INLET,AIR AIR INLET THREAD DIRECTION THE DIRECTION OF THE AIR INLET THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 BJCSD 13THREAD LOCATION,INLET,AIR AIR INLET THREAD LOCATION INDICATES THE LOCATION OF THE AIR INLET THREAD. SELECT REPLY CODE 10AJ91 BJCTD /D/ 07CHOKE,AUTOMATIC AUTOMATIC CHOKE AN INDICATION OF WHETHER OR NOT AN AUTOMATIC CHOKE IS INCLUDED. SELECT REPLY CODE 10AA49 BJCWD /D/ 07GOVERNOR GOVERNOR AN INDICATION OF WHETHER OR NOT A GOVERNOR IS INCLUDED. SELECT REPLY CODE 10AA49 BJCXD /D/ 07PUMP,ACCELERATING ACCELERATING PUMP AN INDICATION OF WHETHER OR NOT AN ACCELERATING PUMP IS INCLUDED. SELECT REPLY CODE 10AA49 BJCYD /D/ 07DEGASSER DEGASSER AN INDICATION OF WHETHER OR NOT A DEGASSER IS INCLUDED. SELECT REPLY CODE 10AA49 BJCZD /D/ 07VALVE,FLIGHT,INVERTED INVERTED FLIGHT VALVE AN INDICATION OF WHETHER OR NOT AN INVERTED FLIGHT VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 BJDBD 18TYPE,BEARING,ROTATING DEVICE ROTATING DEVICE BEARING TYPE INDICATES THE TYPE OF ROTATING DEVICE BEARING(S) PROVIDED. SELECT REPLY CODE 10AB81 BJDCA 12QUANTITY,ROW,ROTATING DEVICE ROTATING DEVICE ROW QUANTITY THE NUMBER OF ROWS OF ROTATING DEVICES PROVIDED. 1A MODE REPLY 0 BJDDG /D/ 19AGENCY,CONTROLLING,CONTACT CONTACT CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE CONTACT. FULL TEXT WRITE-IN 0 BJDFG /D/ 19NUMBER,IDENTIFYING,CONTACT CONTACT IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE CONTACT. FULL TEXT WRITE-IN 0 BJDGJ 04DISTANCE ACROSS WRENCHING SURFACE FLATS DISTANCE ACROSS WRENCHING SURFACE FLATS THE DISTANCE BETWEEN THE FLATS OF A WRENCHING SURFACE. 1D AND 1B MODE REPLY11AA05 BJDHG /D/ 04SIZE,PLATE PLATE SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE PLATE. FULL TEXT WRITE-IN 0 BJDJA /D/ 12QUANTITY,NUT,SELF-LOCKING SELF-LOCKING NUT QUANTITY THE NUMBER OF SELF-LOCKING NUT(S) PROVIDED. 1A MODE REPLY 0 BJDKJ 10INCREMENT,LARGEST,SCALE SCALE LARGEST INCREMENT THE VALUE REPRESENTED BY THE LARGEST MARKINGS ON A SCALE. 1D AND 1B MODE REPLY12AG67 BJDLD /D/ 07SETTING,RANGE,ADJUSTABLE ADJUSTABLE RANGE SETTING AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE RANGE SETTING IS PROVIDED. SELECT REPLY CODE 10AB22 BJDMD /D/ 09MATERIAL,FLOAT FLOAT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FLOAT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH ISAC FROM TBL 230 IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 BJDND /D/ 07CASE,PROTECTIVE,FLOAT FLOAT PROTECTIVE CASE AN INDICATION OF WHETHER OR NOT A PROTECTIVE FLOAT CASE IS PROVIDED. SELECT REPLY CODE 10AB22 BJDPD /D/ 07WIRE,GUIDE,FLOAT FLOAT GUIDE WIRE AN INDICATION OF WHETHER OR NOT A GUIDE WIRE(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BJDQJ 04HEIGHT,BRACKET BRACKET HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A BRACKET,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BJDRJ 04LENGTH,FLANGE FLANGE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A FLANGE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BJDSD /D/ 07SEAL,OIL OIL SEAL AN INDICATION OF WHETHER OR NOT AN OIL SEAL IS PROVIDED. SELECT REPLY CODE 10AB22 BJDTJ 10PRESSURE,OPERATING,MINIMUM MINIMUM OPERATING PRESSURE THE MINIMUM PRESSURE AT WHICH AN ITEM IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY12AJ20 BJDWJ 10PRESSURE,OPERATING,MAXIMUM MAXIMUM OPERATING PRESSURE THE MAXIMUM PRESSURE AT WHICH THE ITEM IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY12AJ20 BJDXD /D/ 07SETTING,RANGE,REMOTE REMOTE RANGE SETTING AN INDICATION OF WHETHER OR NOT A REMOTE RANGE SETTING IS PROVIDED. SELECT REPLY CODE 10AB22 BJDYA 12QUANTITY,CELL,ANEROID ANEROID CELL QUANTITY THE NUMBER OF ANEROID CELLS PROVIDED. 1A MODE REPLY 0 BJDZD 18TYPE,COMMUTATOR COMMUTATOR TYPE INDICATES THE TYPE OF COMMUTATOR PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AM39 BJFBA 12QUANTITY,SEGMENT,CONTACT CONTACT SEGMENT QUANTITY THE NUMBER OF CONTACT SEGMENTS PROVIDED WITH THE ITEM. 1A MODE REPLY 0 BJFCD /D/ 07MECHANISM,CALIBRATION,CONTACT ARM CONTACT ARM CALIBRATION MECHANISM AN INDICATION OF WHETHER OR NOT A CONTACT ARM CALIBRATION MECHANISM IS PROVIDED. SELECT REPLY CODE 10AB22 BJFDA 12QUANTITY,SWITCH,PRESSURE OPERATED PRESSURE OPERATED SWITCH QUANTITY THE NUMBER OF PRESSURE OPERATED SWITCHES PROVIDED. 1A MODE REPLY 0 BJFFJ 04DISTANCE FROM ROD END TO HANDLE DISTANCE FROM ROD END TO HANDLE THE DISTANCE FROM THE END OF THE ROD TO THE START OF THE HANDLE. 2D AND 1B MODE REPLY21AA051AC20 BJFGJ 04WIDTH,ROD ROD WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A ROD,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BJFHJ 04THICKNESS,ROD ROD THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A ROD,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BJFJJ 04DISTANCE FROM ROD END TO SCALE GRADUATION DISTANCE FROM ROD END TO SCALE GRADUATION THE DISTANCE OF SEPARATION FROM THE END OF THE ROD TO THE START OF THE SCALE GRADUATION. 2D AND 1B MODE REPLY21AA051AC20 BJFKJ 10CURRENT RATING,DEVICE,CURRENT MEASURING CURRENT MEASURING DEVICE CURRENT RATING THE CURRENT RATING AT WHICH THE CURRENT MEASURING DEVICE IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY13AJ40 BJFLG /D/ 10VOLTAGE DEVELOPED AT JUNCTION/TEMP RANGE VOLTAGE DEVELOPED AT JUNCTION/TEMP RANGE THE AMOUNT OF VOLTAGE DEVELOPED AT THE JUNCTION AND/OR TEMPERATURE RANGE OF THE ITEM. FULL TEXT WRITE-IN 0 BJFMB 10CAPACITANCE IN PICOFARADS,AIR,RATED RATED AIR CAPACITANCE IN PICOFARADS THE AMOUNT OF AIR CAPACITANCE FOR WHICH THE ITEM IS RATED,EXPRESSED IN PICOFARADS. 1B MODE REPLY 0 BJFND /D/ 07CONNECTION WITH LEAD CONNECTION WITH LEAD AN INDICATION OF WHETHER OR NOT A CONNECTION(S) IS PROVIDED WITH A LEAD(S). SELECT REPLY CODE 10AB22 BJFPD /D/ 07LEAD,CONNECTION,SHIELDED SHIELDED CONNECTION LEAD AN INDICATION OF WHETHER OR NOT A SHIELDED CONNECTION LEAD/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 BJFQJ 04LENGTH,LEAD,CONNECTION CONNECTION LEAD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CONNECTION LEAD INCLUDING THE CONNECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BJFRJ /D/ 04LENGTH FROM END TO CAP,ROD ROD LENGTH FROM END TO CAP THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE ROD END AND AT THE START OF THE CAP. 1D AND 1B MODE REPLY11AA05 BJFSJ /D/ 04LENGTH FROM END TO BREATHER,ROD ROD LENGTH FROM END TO BREATHER THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE ROD END AND AT THE START OF THE BREATHER. 1D AND 1B MODE REPLY11AA05 BJFTJ 04DIAMETER,PORTION,ROD MEASURING ROD MEASURING PORTION DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ROD MEASURING PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BJFWJ 04WIDTH,PORTION,ROD MEASURING ROD MEASURING PORTION WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ROD MEASURING PORTION,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BJFXJ 04THICKNESS,PORTION,ROD MEASURING ROD MEASURING PORTION THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE ROD MEASURING PORTION,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BJFYD 18TYPE,MOUNTING,BREATHER BREATHER MOUNTING TYPE INDICATES THE TYPE OF BREATHER MOUNTING PROVIDED. SELECT REPLY CODE 10AM39 BJFZD 18TYPE,LOCKING,BREATHER BREATHER LOCKING TYPE INDICATES THE TYPE OF BREATHER LOCKING DEVICE PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AE36 BJGBD /D/ 07SLING SLING AN INDICATION OF WHETHER OR NOT A SLING IS INCLUDED. SELECT REPLY CODE 10AA49 BJGCD /D/ 07ADAPTER,HOISTING HOISTING ADAPTER AN INDICATION OF WHETHER OR NOT A HOISTING ADAPTER IS INCLUDED. SELECT REPLY CODE 10AA49 BJGDJ /D/ 04DISTANCE FROM REMOTE CONTROL UNIT DISTANCE FROM REMOTE CONTROL UNIT THE APPROXIMATE DISTANCE FROM THE REMOTE CONTROL UNIT. 3D AND 1B MODE REPLY31AA051AC203AK95 BJGFD 14SHAPE,BASE BASE SHAPE THE PHYSICAL CONFIGURATION OF THE BASE. SELECT REPLY CODE 10AD07 BJGGJ 10CAPACITY,VERTICAL,RATED RATED VERTICAL CAPACITY A MEASUREMENT OF THE RATED CAPACITY THE ITEM CAN LIFT VERTICALLY. 1D AND 1B MODE REPLY12AG67 BJGHJ 04DISTANCE,LIFTING,HYDRAULIC HYDRAULIC LIFTING DISTANCE THE HYDRAULIC LIFTING DISTANCE OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BJGJJ 04HEIGHT,EXTENDED EXTENDED HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE ITEM WHEN FULLY EXTENDED,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BJGKJ 04DIAMETER,OUTSIDE,PISTON CYLINDER HOUSING PISTON CYLINDER HOUSING OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PISTON CYLINDER HOUSING,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BJGLD /D/ 07EXTENSION,SCREW SCREW EXTENSION AN INDICATION OF WHETHER OR NOT A SCREW EXTENSION IS INCLUDED. SELECT REPLY CODE 10AA49 BJGMJ A18TYPE AND QUANTITY,PUMP PUMP TYPE AND QUANTITY INDICATES THE PUMP TYPE UTILIZED AND THE NUMBER PROVIDED. 1D AND 1A MODE REPLY12AC58 BJGND /D/ 07PROVISION,MOUNTING,POWER OPERATED PUMP POWER OPERATED PUMP MOUNTING PROVISION AN INDICATION OF WHETHER OR NOT A POWER OPERATED PUMP MOUNTING PROVISION IS PROVIDED. SELECT REPLY CODE 10AB22 BJGPD 19RELATIONSHIP TO LIFTING DEVICE,PUMP PUMP RELATIONSHIP TO LIFTING DEVICE INDICATES THE RELATIONSHIP OF THE PUMP TO THE LIFTING DEVICE. SELECT REPLY CODE 10AD15 BJGQD /D/ 07CRANE,REMOVAL,WHEEL WHEEL REMOVAL CRANE AN INDICATION OF WHETHER OR NOT A WHEEL REMOVAL CRANE IS INCLUDED. SELECT REPLY CODE 10AA49 BJGRJ 04DIAMETER,OUTSIDE,TIRE ACCOMMODATION TIRE ACCOMMODATION OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TIRE ACCOMMODATION,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BJGSG 03DESIGNATION,GOVERNMENT,REPRESENTED REPRESENTED GOVERNMENT DESIGNATION A DESIGNATION INDICATING THE GOVERNMENT OR NATION OF WHICH THE ITEM IS REPRESENTATIVE. FULL TEXT WRITE-IN 0 BJGTD 18TYPE,AIRFOIL,AIRCRAFT AIRCRAFT AIRFOIL TYPE INDICATES THE TYPE OF AIRCRAFT AIRFOIL WITH WHICH THE ITEM IS PROVIDED. SELECT REPLY CODE 10AM91 BJGWG 10SCALE,AIRCRAFT AIRCRAFT SCALE A GRADUATED MEASUREMENT OF AN AIRCRAFT WHEREIN THE ACTUAL LINEAR DIMENSION IS REPRESENTED BY A SMALLER LINEAR DIMENSION. FULL TEXT WRITE-IN 0 BJGXD /D/ 07LATCH LATCH AN INDICATION OF WHETHER OR NOT A LATCH IS INCLUDED. SELECT REPLY CODE 10AA49 BJGYD 18TYPE,LATCH LATCH TYPE INDICATES THE TYPE OF LATCH PROVIDED. SELECT REPLY CODE 10AC52 BJGZA 12QUANTITY,LATCH LATCH QUANTITY THE NUMBER OF LATCH(ES) PROVIDED. 1A MODE REPLY 0 BJHBD /D/ 07OPENING,DUCT,PREHEATER PREHEATER DUCT OPENING AN INDICATION OF WHETHER OR NOT A PREHEATER DUCT OPENING IS INCLUDED. SELECT REPLY CODE 10AA49 BJHCJ 04HEIGHT,PLATFORM PLATFORM HEIGHT A MEASUREMENT OF THE DISTANCE FROM THE BOTTOM TO THE TOP SURFACE OF THE PLATFORM. 2D AND 1B MODE REPLY21AA051AC20 BJHDG 04LENGTH,STEP STEP LENGTH A MEASUREMENT OF THE VARIABLE DIMENSIONS OF THE STEPS,IN DISTINCTION FROM WIDTH. FULL TEXT WRITE-IN 0 BJHFG 04WIDTH,STEP STEP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE STEP,IN DISTINCTION FROM THICKNESS. FULL TEXT WRITE-IN 0 BJHGD /D/ 07TIRE,PNEUMATIC PNEUMATIC TIRE AN INDICATION OF WHETHER OR NOT A PNEUMATIC TIRE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BJHJA 12QUANTITY,CASTER CASTER QUANTITY THE NUMBER OF CASTERS PROVIDED ON THE ITEM. 1A MODE REPLY 0 BJHKD 18TYPE,CASTER CASTER TYPE INDICATES THE TYPE OF CASTERS PROVIDED. SELECT REPLY CODE 10AL49 BJHLG /D/ 03DESIGNATION,UNIT,MOBILE MOBILE UNIT DESIGNATION THE DESIGNATION BY WHICH THE MOBILE UNIT IS IDENTIFIED. FULL TEXT WRITE-IN 0 BJHMD /D/ 08LOCATION,SPUD,INLET INLET SPUD LOCATION INDICATES THE LOCATION OF THE INLET SPUD ON THE ITEM. SELECT REPLY CODE 10AJ91 BJHND /D/ 07STRAP,RETAINING,BOMB BOMB RETAINING STRAP AN INDICATION OF WHETHER OR NOT A BOMB RETAINING STRAP IS INCLUDED. SELECT REPLY CODE 10AA49 BJHPD 18TYPE,ACTION,FLUSHING FLUSHING ACTION TYPE INDICATES THE TYPE OF FLUSHING ACTION PROVIDED. SELECT REPLY CODE 10AJ27 BJHQD 18TYPE,TRAP,BOWL BOWL TRAP TYPE INDICATES THE TYPE OF BOWL TRAP PROVIDED. SELECT REPLY CODE 10AM39 BJHRJ 04SIZE,SPUD,INLET INLET SPUD SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSION OF THE INLET SPUD. 1D AND 1B MODE REPLY11AA05 BJHSD /D/ 19CONSTRUCTION,TANK/BOWL TANK/BOWL CONSTRUCTION AN INDICATION OF THE STRUCTURAL CHARACTERISTICS OF THE TANK AND/OR BOWL. SELECT REPLY CODE 10AC66 BJHTD /D/ 08LOCATION,OUTLET OUTLET LOCATION INDICATES THE LOCATION OF THE OUTLET ON THE ITEM. SELECT REPLY CODE 10AJ91 BJHWD /D/ 07SEAT,INTEGRAL INTEGRAL SEAT AN INDICATION OF WHETHER OR NOT AN INTEGRAL SEAT IS INCLUDED. SELECT REPLY CODE 10AA49 BJHXD /D/ 18TYPE,PROTRUSION,COVER/PLUG COVER/PLUG PROTRUSION TYPE INDICATES THE TYPE OF COVER AND/OR PLUG PROTRUSION PROVIDED. SELECT REPLY CODE 10AK12 BJHYD /D/ 19CLOSET FOR WHICH DESIGNED,WATER WATER CLOSET FOR WHICH DESIGNED INDICATES THE WATER CLOSET FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BJHZD /D/ 07SEAT SEAT AN INDICATION OF WHETHER OR NOT A SEAT IS INCLUDED. SELECT REPLY CODE 10AA49 BJJBD /D/ 07ECONOMIZER,VACUUM VACUUM ECONOMIZER AN INDICATION OF WHETHER OR NOT A VACUUM ECONOMIZER IS INCLUDED. SELECT REPLY CODE 10AA49 BJJCD /D/ 07BOOSTER,VACUUM VACUUM BOOSTER AN INDICATION OF WHETHER OR NOT A VACUUM BOOSTER IS INCLUDED. SELECT REPLY CODE 10AA49 BJJDD 08LOCATION,BOOSTER,VACUUM VACUUM BOOSTER LOCATION INDICATES THE LOCATION OF THE VACUUM BOOSTER ON THE ITEM. SELECT REPLY CODE 10AJ91 BJJFG /D/ 10VACUUM IN RPM,MINIMUM MINIMUM VACUUM IN RPM THE REQUIRED MINIMUM VACUUM,EXPRESSED IN REVOLUTIONS PER MINUTE. FULL TEXT WRITE-IN 0 BJJGD /D/ 07FILTER,FUEL FUEL FILTER AN INDICATION OF WHETHER OR NOT A FUEL FILTER IS INCLUDED. SELECT REPLY CODE 10AA49 BJJHD 08LOCATION,FILTER,FUEL FUEL FILTER LOCATION INDICATES THE LOCATION OF THE FUEL FILTER ON THE ITEM. SELECT REPLY CODE 10AJ91 BJJJD /D/ 07LEVER,PRIMING PRIMING LEVER AN INDICATION OF WHETHER OR NOT A PRIMING LEVER IS INCLUDED. SELECT REPLY CODE 10AA49 BJJKG /D/ 10PRESSURE ABOVE OUTLET HEIGHT,STATIC,MAXIMUM MAXIMUM STATIC PRESSURE ABOVE OUTLET HEIGHT THE MAXIMUM STATIC PRESSURE OF THE ITEM ABOVE THE OUTLET HEIGHT. FULL TEXT WRITE-IN 0 BJJLG /D/ 04DISTANCE FROM PUMP MOUNTING FACE TO ACTUATOR CENTER DISTANCE FROM PUMP MOUNTING FACE TO ACTUATOR CENTER THE DISTANCE FROM THE MOUNTING FACE OF THE PUMP TO THE CENTER OF THE ACTUATOR. FULL TEXT WRITE-IN 0 BJJMG /D/ 18TYPE/SIZE,CONNECTION,INLET INLET CONNECTION TYPE/SIZE INDICATES THE TYPE AND SIZE OF THE INLET CONNECTION(S) ON THE ITEM. FULL TEXT WRITE-IN 0 BJJNG /D/ 18TYPE/SIZE,CONNECTION,OUTLET OUTLET CONNECTION TYPE/SIZE INDICATES THE TYPE AND SIZE OF THE OUTLET CONNECTION(S) ON THE ITEM. FULL TEXT WRITE-IN 0 BJJPD /D/ 07FACILITY,DRAIN DRAIN FACILITY AN INDICATION OF WHETHER OR NOT A DRAIN FACILITY(IES) IS INCLUDED. SELECT REPLY CODE 10AA49 BJJQD /D/ 07NECK,FILLER FILLER NECK AN INDICATION OF WHETHER OR NOT A FILLER NECK IS INCLUDED. SELECT REPLY CODE 10AA49 BJJRJ 04DISTANCE FROM FILLER NECK END TO TANK BODY DISTANCE FROM FILLER NECK END TO TANK BODY THE DISTANCE FROM THE FILLER NECK END TO THE TANK BODY. 2D AND 1B MODE REPLY21AA051AC20 BJJSD /D/ 18TYPE FOR WHICH FILLER OPENING IS DESIGNED,CAP CAP TYPE FOR WHICH FILLER OPENING IS DESIGNED INDICATES THE TYPE OF CAP FOR WHICH THE FILLER OPENING IS DESIGNED. SELECT REPLY CODE 10AK54 BJJTD /D/ 08LOCATION,OPENING,LINE CONNECTION LINE CONNECTION OPENING LOCATION INDICATES THE LOCATION OF THE LINE CONNECTION OPENING(S) IN THE ITEM. SELECT REPLY CODE 10AJ91 BJJWD 11METHOD,CONNECTION,OPENING OPENING CONNECTION METHOD THE MEANS USED FOR CONNECTING TO AN OPENING. SELECT REPLY CODE 10AJ68 BJJXG 04SIZE,CONNECTION,OPENING OPENING CONNECTION SIZE DESIGNATES THE SIZE OF THE CONNECTION OPENING PROVIDED. FULL TEXT WRITE-IN 0 BJJYD /D/ 07OPENING,DRAIN DRAIN OPENING AN INDICATION OF WHETHER OR NOT A DRAIN OPENING IS INCLUDED. SELECT REPLY CODE 10AA49 BJJZG 19EQUIPMENT ON WHICH MOUNTED EQUIPMENT ON WHICH MOUNTED INDICATES THE EQUIPMENT ON WHICH THE ITEM IS MOUNTED. FULL TEXT WRITE-IN 0 BJKBD /D/ 07TRANSMITTER,QUANTITY,LIQUID LIQUID QUANTITY TRANSMITTER AN INDICATION OF WHETHER OR NOT A LIQUID QUANTITY TRANSMITTER IS INCLUDED. SELECT REPLY CODE 10AA49 BJKCJ 10CURRENT RATING,MAXIMUM MAXIMUM CURRENT RATING THE MAXIMUM CONTINUOUS CURRENT WHICH MUST NOT BE EXCEEDED IN ORDER TO AVOID DAMAGE TO THE ITEM. 2D AND 1B MODE REPLY21AC302AK53 BJKDG 19ARRANGEMENT,CONTACT CONTACT ARRANGEMENT THE DESIGNATION THAT IDENTIFIES THE SCHEMATIC DIAGRAM OF THE CONTACT ARRANGEMENT. FULL TEXT WRITE-IN 0 BJKFD /D/ 19POSITION,FLOAT FLOAT POSITION INDICATES THE POSITION OF THE FLOAT. SELECT REPLY CODE 10AC65 BJKGD /D/ 07RELAY RELAY AN INDICATION OF WHETHER OR NOT A RELAY IS INCLUDED. SELECT REPLY CODE 10AA49 BJKHD 18TYPE FOR WHICH DESIGNED,LIQUID LIQUID TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF LIQUID(S) FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AB75 BJKJD 19FUEL FOR WHICH DESIGNED,AIRCRAFT AIRCRAFT FUEL FOR WHICH DESIGNED THE AIRCRAFT FUEL FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AN21 BJKKG /D/ 19SPECIFICATION,GRADE,AIRCRAFT FUEL AIRCRAFT FUEL GRADE SPECIFICATION THE ALPHA/NUMERIC OR SYMBOL USED TO IDENTIFY THE SPECIFICATION PERTAINING TO THE AIRCRAFT FUEL. FULL TEXT WRITE-IN 0 BJKLG /D/ 19GRADE,FUEL,AIRCRAFT AIRCRAFT FUEL GRADE THE ALPHA/NUMERIC OR SYMBOL USED TO DENOTE THE AIRCRAFT FUEL GRADE. FULL TEXT WRITE-IN 0 BJKMG /D/ 10GRAVITY RATING,SPECIFIC,AIRCRAFT FUEL GRADE AIRCRAFT FUEL GRADE SPECIFIC GRAVITY RATING AN INDICATION OF THE SPECIFIC GRAVITY RATING OF THE GRADE OF AIRCRAFT FUEL. FULL TEXT WRITE-IN 0 BJKNJ 10TRAVEL,EFFECTIVE,FLOAT FLOAT EFFECTIVE TRAVEL THE DISTANCE OF THE EFFECTIVE TRAVEL OF THE FLOAT. 2D AND 1B MODE REPLY21AA051AC20 BJKPG /D/ 19DIMENSIONS,MOUNTING MOUNTING DIMENSIONS THE MOUNTING DIMENSIONS OF THE ITEM. FULL TEXT WRITE-IN 0 BJKQJ 04LENGTH,INSERTION,TANK TANK INSERTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION FROM THE MOUNTING SURFACE TO THE END OF THE ITEM,WHICH IS DESIGNED TO BE INSERTED INTO THE TANK. 2D AND 1B MODE REPLY21AA051AC20 BJKRD 08LOCATION,TANK TANK LOCATION INDICATES THE LOCATION OF THE TANK(S). SELECT REPLY CODE 10AJ91 BJKSD /D/ 09MATERIAL,TANK TANK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TANK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BJKTJ 04HEIGHT,TANK TANK HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A TANK,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BJKWJ 04WIDTH,TANK TANK WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TANK,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BJKXJ 04THICKNESS,TANK TANK THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A TANK,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BJKYA 12QUANTITY,CORE CORE QUANTITY THE NUMBER OF CORES PROVIDED. 1A MODE REPLY 0 BJKZJ 04LENGTH,TANK,PROCESSING PROCESSING TANK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE PROCESSING TANK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BJLBJ 04WIDTH,TANK,PROCESSING PROCESSING TANK WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PROCESSING TANK,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BJLCD /D/ 09MATERIAL,TANK,PROCESSING PROCESSING TANK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PROCESSING TANK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BJLDJ 04DEPTH,TANK,PROCESSING PROCESSING TANK DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE PROCESSING TANK,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 BJLFD /D/ 18TYPE,SOURCE,OUTPUT ELECTRICAL POWER OUTPUT ELECTRICAL POWER SOURCE TYPE INDICATES THE TYPE OF OUTPUT ELECTRICAL POWER SOURCE INCLUDED. SELECT REPLY CODE 10AJ13 BJLGJ /D/ 10FREQUENCY RATING,OUTPUT,POWER SUPPLY POWER SUPPLY OUTPUT FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE POWER SUPPLY OUTPUT IS RATED. 2D AND 1B MODE REPLY21AC321AC20 BJLHD /D/ 07MOUNTED,CABINET,EXTRA PROCESSING TANK EXTRA PROCESSING TANK CABINET MOUNTED AN INDICATION OF WHETHER OR NOT AN ADDITIONAL CABINET MOUNTED PROCESSING TANK IS INCLUDED. SELECT REPLY CODE 10AA49 BJLJA /D/ 12QUANTITY,TRAY,PROCESSING PROCESSING TRAY QUANTITY THE NUMBER OF PROCESSING TRAY(S) INCLUDED WITH THE ITEM. 1A MODE REPLY 0 BJLKD /D/ 09MATERIAL,TRAY,PROCESSING PROCESSING TRAY MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PROCESSING TRAY IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BJLLD /D/ 07BOTTOM,FALSE,PROCESSING TRAY PROCESSING TRAY FALSE BOTTOM AN INDICATION OF WHETHER OR NOT A FALSE BOTTOM PROCESSING TRAY IS INCLUDED. SELECT REPLY CODE 10AA49 BJLMD /D/ 07CRYSTAL,CALIBRATION,INTERNAL INTERNAL CALIBRATION CRYSTAL AN INDICATION OF WHETHER OR NOT AN INTERNAL CALIBRATION CRYSTAL(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BJLNJ /D/ 04LENGTH,INSIDE,PROCESSING TRAY PROCESSING TRAY INSIDE LENGTH THE INSIDE MEASUREMENT OF THE LONGEST DIMENSION OF THE PROCESSING TRAY,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BJLPJ /D/ 04WIDTH,INSIDE,PROCESSING TRAY PROCESSING TRAY INSIDE WIDTH THE INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PROCESSING TRAY,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BJLQJ /D/ 04DEPTH,INSIDE,PROCESSING TRAY PROCESSING TRAY INSIDE DEPTH THE INSIDE MEASUREMENT BETWEEN SPECIFIED POINTS ON THE PROCESSING TRAY,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 BJLRD /D/ 07FEATURE,CONTROLLED,TEMP TEMP CONTROLLED FEATURE AN INDICATION OF WHETHER OR NOT A CONTROLLED TEMPERATURE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BJLSD /D/ 07CABINET,CONTROLLED,TEMP TEMP CONTROLLED CABINET AN INDICATION OF WHETHER OR NOT A TEMPERATURE CONTROLLED CABINET IS PROVIDED. SELECT REPLY CODE 10AB22 BJLTD /D/ 07EDGE,TOP,BEADED BEADED TOP EDGE AN INDICATION OF WHETHER OR NOT A BEADED TOP EDGE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BJLWD 11METHOD,DRAINING DRAINING METHOD THE MEANS USED TO DRAIN THE ITEM. SELECT REPLY CODE 10AH83 BJLXJ 10RESISTANCE RATING,FIRE FIRE RESISTANCE RATING THE LENGTH OF TIME IN WHICH THE ITEM WILL RESIST FIRE. 1D AND 1B MODE REPLY12AG67 BJLYD /D/ 07FEATURE,CONTROL,HUMIDITY HUMIDITY CONTROL FEATURE AN INDICATION OF WHETHER OR NOT A HUMIDITY CONTROL FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BJLZD /D/ 07BASE,REMOVABLE REMOVABLE BASE AN INDICATION OF WHETHER OR NOT A REMOVABLE BASE IS INCLUDED. SELECT REPLY CODE 10AA49 BJMBD /D/ 17SURFACE TREATMENT,CABINET CABINET SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE CABINET. SELECT REPLY CODE 10AD09 BJMCJ 04LENGTH,OVERALL,CABINET CABINET OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CABINET. 2D AND 1B MODE REPLY21AA051AC20 BJMDD /D/ 07MOTOR,SPEED,VARIABLE VARIABLE SPEED MOTOR AN INDICATION OF WHETHER OR NOT A VARIABLE SPEED MOTOR IS INCLUDED. SELECT REPLY CODE 10AA49 BJMFD 04SIZE,DRAWER DRAWER SIZE DESIGNATES THE SIZE OF THE DRAWER. SELECT REPLY CODE 10AF81 BJMGJ 04LENGTH,INSIDE,OVERALL OVERALL INSIDE LENGTH THE INSIDE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE ENDS OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BJMHJ 04WIDTH,INSIDE,OVERALL OVERALL INSIDE WIDTH AN OVERALL INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BJMJJ 04DEPTH,INSIDE,OVERALL OVERALL INSIDE DEPTH AN OVERALL INSIDE MEASUREMENT BETWEEN SPECIFIED POINTS OF AN ITEM,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BJMKD /D/ 07FAUCET FAUCET AN INDICATION OF WHETHER OR NOT A FAUCET IS INCLUDED. SELECT REPLY CODE 10AA49 BJMLD /D/ 09MATERIAL,BASIN BASIN MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BASIN IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BJMMD /D/ 07KNIFE,TRIMMING,TOP FITTED TOP FITTED TRIMMING KNIFE AN INDICATION OF WHETHER OR NOT A TOP FITTED TRIMMING KNIFE/VES/ IS INCLUDED. SELECT REPLY CODE 10AA49 BJMNA /D/ 12QUANTITY,REWINDER REWINDER QUANTITY THE NUMBER OF REWINDER(S) FURNISHED WITH THE ITEM. 1A MODE REPLY 0 BJMPD /D/ 08LOCATION,REWINDER REWINDER LOCATION INDICATES THE LOCATION OF THE REWINDER(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 BJMQD /D/ 07VENT,FUME FUME VENT AN INDICATION OF WHETHER OR NOT A FUME VENT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BJMRD /D/ 07HEAD,SPRINKLER SPRINKLER HEAD AN INDICATION OF WHETHER OR NOT A SPRINKLER HEAD IS INCLUDED. SELECT REPLY CODE 10AA49 BJMSD /D/ 07FEATURE,STEREOSCOPIC STEREOSCOPIC FEATURE AN INDICATION OF WHETHER OR NOT A STEREOSCOPIC FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BJMTD 02DESIGN,CASE,CARRYING CARRYING CASE DESIGN INDICATES THE TYPE OF FUNCTION(S) FOR WHICH THE CARRYING CASE IS DESIGNED. SELECT REPLY CODE 10AK54 BJMWJ 04WIDTH ACCOMMODATED,PAPER PAPER WIDTH ACCOMMODATED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PAPER ACCOMMODATED,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BJMXD 18TYPE,LOADING LOADING TYPE INDICATES THE TYPE OF LOADING PROVIDED. SELECT REPLY CODE 10AG37 BJMYA 12QUANTITY,FILM,SHEET SHEET FILM QUANTITY THE NUMBER OF FILM SHEET(S) THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 BJMZJ A19NUMBER,IDENTIFYING,ACCOMMODATED EQUIPMENT ACCOMMODATED EQUIPMENT IDENTIFYING NUMBER THE NUMBER USED TO IDENTIFY THE EQUIPMENT THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1A MODE REPLY12AG99 BJNBD 18TYPE,DEVICE,OPENING OPENING DEVICE TYPE INDICATES THE TYPE OF DEVICE FURNISHED ON OR WITH THE ITEM FOR THE PURPOSE OF OPENING. SELECT REPLY CODE 10AC58 BJNCD 18TYPE,LINING,END END LINING TYPE INDICATES THE TYPE OF END LINING PROVIDED. SELECT REPLY CODE 10AB90 BJNDJ 04DIAMETER,OVERALL,INNER CONTAINER INNER CONTAINER OVERALL DIAMETER THE OVERALL LENGTH OF A STRAIGNT LINE WHICH PASSES THROUGH THE CENTER OF AN INNER CONTAINER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BJNFJ 04DEPTH,OVERALL,CONTAINER,INNER INNER CONTAINER OVERALL DEPTH AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF THE INNER CONTAINER,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BJNGA 19NUMBER,DESIGNATION,ICC ICC DESIGNATION NUMBER A DESIGNATION NUMBER ASSIGNED TO THE ITEM,IN ACCORDANCE WITH THE INTERSTATE COMMERCE COMMISSION REGULATIONS. 1A MODE REPLY 0 BJNHD 18TYPE,DUNNAGE DUNNAGE TYPE INDICATES THE TYPE OF DUNNAGE PROVIDED. SELECT REPLY CODE 10AK54 BJNJD /D/ 07SHELF,SECTION,DISPLAY DISPLAY SECTION SHELF AN INDICATION OF WHETHER OR NOT A DISPLAY SECTION SHELF IS INCLUDED. SELECT REPLY CODE 10AA49 BJNKD /D/ 07DOOR,SECTION,DISPLAY DISPLAY SECTION DOOR AN INDICATION OF WHETHER OR NOT A DISPLAY SECTION DOOR IS INCLUDED. SELECT REPLY CODE 10AA49 BJNLD 18TYPE,FIXTURE,DISPLAY SECTION LIGHT DISPLAY SECTION LIGHT FIXTURE TYPE INDICATES THE TYPE OF DISPLAY SECTION LIGHT FIXTURE(S) PROVIDED. SELECT REPLY CODE 10AD48 BJNMD 18TYPE,COMPARTMENT COMPARTMENT TYPE INDICATES THE TYPE OF COMPARTMENT PROVIDED. SELECT REPLY CODE 10AK54 BJNNJ 04WIDTH,DRAWER DRAWER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A DRAWER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BJNPJ /D/ 04WIDTH,COMPARTMENT COMPARTMENT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE COMPARTMENT AT THE OPENING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BJNQD /D/ 07FEATURE,RESISTANCE,MOISTURE MOISTURE RESISTANCE FEATURE AN INDICATION OF WHETHER OR NOT A MOISTURE RESISTANCE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BJNRD 18TYPE,HANDLE,STRAP STRAP HANDLE TYPE INDICATES THE TYPE OF STRAP HANDLE PROVIDED. SELECT REPLY CODE 10AC55 BJNSJ /D/ 10CAPACITY RATING,SHELF,CABINET DISPLAY CABINET DISPLAY SHELF CAPACITY RATING A MEASUREMENT OF THE RATED CAPACITY OF THE CABINET DISPLAY SHELF. 2D AND 1B MODE REPLY22AG671AC20 BJNTJ /D/ 10CAPACITY RATING,SHELF,CABINET STORAGE CABINET STORAGE SHELF CAPACITY RATING A MEASUREMENT OF THE RATED CAPACITY OF THE CABINET STORAGE SHELF. 2D AND 1B MODE REPLY22AG671AC20 BJNWJ 04WIDTH,OVERALL,CABINET CABINET OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A CABINET,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BJNXJ 04HEIGHT,OVERALL,CABINET CABINET OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE CABINET. 2D AND 1B MODE REPLY21AA051AC20 BJNYJ /D/ 04DEPTH,OVERALL,CABINET CABINET OVERALL DEPTH AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF A CABINET,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BJNZD /D/ 09MATERIAL,SHELL,EXTERIOR,CABINET CABINET EXTERIOR SHELL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CABINET EXTERIOR SHELL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BJPBA 12QUANTITY,DOOR,CABINET CABINET DOOR QUANTITY THE NUMBER OF CABINET DOORS PROVIDED. 1A MODE REPLY 0 BJPCD 18TYPE,CABINET CABINET TYPE INDICATES THE TYPE OF CABINET PROVIDED. SELECT REPLY CODE 10AL59 BJPDD /D/ 07ATTACHMENT,SPRAY SPRAY ATTACHMENT AN INDICATION OF WHETHER OR NOT A SPRAY ATTACHMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BJPFD /D/ 07RACK RACK AN INDICATION OF WHETHER OR NOT A RACK IS INCLUDED. SELECT REPLY CODE 10AA49 BJPGD 08LOCATION,INSCRIPTION INSCRIPTION LOCATION INDICATES THE LOCATION OF THE INSCRIPTION ON THE ITEM. SELECT REPLY CODE 10AJ91 BJPHJ 04LENGTH,STRAP,SHOULDER SHOULDER STRAP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SHOULDER STRAP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BJPJJ 04WIDTH,STRAP,SHOULDER SHOULDER STRAP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SHOULDER STRAP,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BJPLD /D/ 07HEATER,BUILT-IN BUILT-IN HEATER AN INDICATION OF WHETHER OR NOT A BUILT-IN HEATER IS INCLUDED. SELECT REPLY CODE 10AA49 BJPMJ 04DISTANCE BETWEEN PRONGS DISTANCE BETWEEN PRONGS THE DISTANCE BETWEEN THE PRONGS ON THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BJPNJ 10CAPACITY,PRONG PRONG CAPACITY A MEASUREMENT OF THE AMOUNT THE PRONGS WILL HOLD. 2D AND 1B MODE REPLY21AA051AC20 BJPPG 19NAME FOR WHICH DESIGNED,FINDER,LIST LIST FINDER NAME FOR WHICH DESIGNED THE NAME OF THE LIST FINDER FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 BJPQG 19MODEL FOR WHICH DESIGNED,FINDER,LIST LIST FINDER MODEL FOR WHICH DESIGNED THE LIST FINDER MODEL FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 BJPRD 14SHAPE,DISK DISK SHAPE THE PHYSICAL CONFIGURATION OF THE DISK. SELECT REPLY CODE 10AD07 BJPSD /D/ 09MATERIAL,CASING CASING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CASING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BJPTD /D/ 07BRUSH BRUSH AN INDICATION OF WHETHER OR NOT A BRUSH IS INCLUDED. SELECT REPLY CODE 10AA49 BJPWD /D/ 07COVERING,PROTECTIVE,BASE BASE PROTECTIVE COVERING AN INDICATION OF WHETHER OR NOT A PROTECTIVE COVERING IS INCLUDED ON THE BASE. SELECT REPLY CODE 10AA49 BJPXJ 04DIAMETER,OUTSIDE,ACCOMMODATED TAPE ROLL ACCOMMODATED TAPE ROLL OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TAPE ROLL FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BJPYJ 04DIAMETER,INSIDE,TAPE CORE TAPE CORE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TAPE CORE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BJPZJ 10CIRCUMFERENCE,BLADE,EXTENDED EXTENDED BLADE CIRCUMFERENCE THE MEASUREMENT OF THE PERIMETER OF A CIRCLE CIRCUMSCRIBED BY THE ROTARY MOTION OF THE EXTENDED BLADE. 2D AND 1B MODE REPLY21AA051AC20 BJQBJ 10MEASUREMENT,ROUGHING-IN,MINIMUM MINIMUM ROUGHING-IN MEASUREMENT THE MINIMUM ROUGHING-IN MEASUREMENT REQUIRED. 1D AND 1B MODE REPLY11AA05 BJQCD 02DESIGN,SEAT SEAT DESIGN THE DESIGN CHARACTERISTIC OF THE SEAT. SELECT REPLY CODE 10AL52 BJQDD 08LOCATION,TANK,MOUNTED MOUNTED TANK LOCATION INDICATES THE LOCATION OF THE MOUNTED TANK ON THE ITEM. SELECT REPLY CODE 10AJ91 BJQFD /D/ 17SURFACE TREATMENT,TANK TANK SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE TANK SURFACE. SELECT REPLY CODE 10AD09 BJQGD 01COLOR,TANK TANK COLOR THE HUE OR TINT OF THE TANK. SELECT REPLY CODE 10AD06 BJQHD /D/ 07BACK,EXTENDED EXTENDED BACK AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES AN EXTENDED BACK. SELECT REPLY CODE 10AA49 BJQJD /D/ 07COVER,SEAT SEAT COVER AN INDICATION OF WHETHER OR NOT A SEAT COVER IS PROVIDED. SELECT REPLY CODE 10AB22 BJQKD /D/ 17SURFACE TREATMENT,SEAT SEAT SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SEAT SURFACE. SELECT REPLY CODE 10AD09 BJQLD 01COLOR,SEAT SEAT COLOR THE HUE OR TINT OF THE SEAT. SELECT REPLY CODE 10AD06 BJQMD /D/ 07CHARACTERISTIC,DESIGN,JUVENILE JUVENILE DESIGN CHARACTERISTIC AN INDICATION OF WHETHER OR NOT A JUVENILE DESIGN CHARACTERISTIC IS PROVIDED. SELECT REPLY CODE 10AB22 BJQND 02DESIGN,PIPE,WATER SUPPLY WATER SUPPLY PIPE DESIGN THE DESIGN CHARACTERISTIC(S) OF THE WATER SUPPLY PIPE. SELECT REPLY CODE 10AD07 BJQPD 02DESIGN,VALVE,WATER SUPPLY PIPE WATER SUPPLY PIPE VALVE DESIGN THE DESIGN CHARACTERISTIC(S) OF THE WATER SUPPLY PIPE VALVE. SELECT REPLY CODE 10AD07 BJQRD 18TYPE,HINGE HINGE TYPE INDICATES THE TYPE OF HINGE(S) PROVIDED. SELECT REPLY CODE 10AK54 BJQSD /D/ 17SURFACE TREATMENT,HINGE HINGE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE HINGE SURFACE. SELECT REPLY CODE 10AD09 BJQTD 18TYPE,ENAMEL,GLAZED GLAZED ENAMEL TYPE INDICATES THE TYPE OF GLAZED ENAMEL PROVIDED. SELECT REPLY CODE 10AA65 BJQWD /D/ 07DRAINBOARD,INTEGRAL INTEGRAL DRAINBOARD AN INDICATION OF WHETHER OR NOT AN INTEGRAL DRAINBOARD IS INCLUDED. SELECT REPLY CODE 10AA49 BJQXD 08LOCATION,DRAINBOARD DRAINBOARD LOCATION INDICATES THE LOCATION OF THE DRAINBOARD(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 BJQYD /D/ 07BACK,SPLASH SPLASH BACK AN INDICATION OF WHETHER OR NOT A SPLASH BACK IS PROVIDED. SELECT REPLY CODE 10AB22 BJQZD /D/ 07CORNER,BACK,SPLASH SPLASH BACK CORNER AN INDICATION OF WHETHER OR NOT CORNERS ARE PROVIDED ON THE SPLASH BACK. SELECT REPLY CODE 10AB22 BJRBD 08LOCATION,CORNER CORNER LOCATION INDICATES THE LOCATION OF THE CORNER(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 BJRCD /D/ 07BACK,LEDGE LEDGE BACK AN INDICATION OF WHETHER OR NOT A LEDGE BACK IS PROVIDED. SELECT REPLY CODE 10AB22 BJRDD 02DESIGN,RIM RIM DESIGN THE DESIGN CHARACTERISITC(S) OF THE RIM. SELECT REPLY CODE 10AK54 BJRFD /D/ 07HEATER,WATER,STEAM STEAM WATER HEATER AN INDICATION OF WHETHER OR NOT A STEAM WATER HEATER IS INCLUDED. SELECT REPLY CODE 10AA49 BJRGA /D/ 12QUANTITY,DRAWER,CABINET CABINET DRAWER QUANTITY THE NUMBER OF CABINET DRAWER(S) PROVIDED. 1A MODE REPLY 0 BJRHJ 04DIAMETER,OPENING,DRAIN DRAIN OPENING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DRAIN OPENING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BJRJD 08LOCATION,OPENING,DRAIN DRAIN OPENING LOCATION INDICATES THE LOCATION OF THE DRAIN OPENING ON THE ITEM. SELECT REPLY CODE 10AJ91 BJRKD 08LOCATION,OPENING,SUPPLY SUPPLY OPENING LOCATION INDICATES THE LOCATION OF THE SUPPLY OPENING ON THE ITEM. SELECT REPLY CODE 10AJ91 BJRLJ /D/ 04DISTANCE BETWEEN HOT/COLD SUPPLY OPENINGS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN HOT/COLD SUPPLY OPENINGS THE CENTER TO CENTER DISTANCE BETWEEN THE HOT/COLD SUPPLY OPENINGS. 2D AND 1B MODE REPLY21AA051AC20 BJRMD /D/ 07OPENING,SPOUT SPOUT OPENING AN INDICATION OF WHETHER OR NOT A SPOUT OPENING IS PROVIDED. SELECT REPLY CODE 10AB22 BJRND /D/ 07OPENING,SUPPLY,SEPARATE DRINKING WATER SEPARATE DRINKING WATER SUPPLY OPENING AN INDICATION OF WHETHER OR NOT A SEPARATE DRINKING WATER SUPPLY OPENING IS PROVIDED. SELECT REPLY CODE 10AB22 BJRPD /D/ 07OPENING,SPRAY SPRAY OPENING AN INDICATION OF WHETHER OR NOT A SPRAY OPENING IS PROVIDED. SELECT REPLY CODE 10AB22 BJRQD /D/ 07OPENING FOR COMBINATION FAUCET,SINGLE SINGLE OPENING FOR COMBINATION FAUCET AN INDICATION OF WHETHER OR NOT A SINGLE OPENING FOR A COMBINATION FAUCET IS PROVIDED. SELECT REPLY CODE 10AB22 BJRRD 18TYPE,SEAT,COMPRESSION COMPRESSION SEAT TYPE INDICATES THE TYPE OF COMPRESSION SEAT PROVIDED. SELECT REPLY CODE 10AL52 BJRSD 18TYPE,OPERATION,SHUTOFF SHUTOFF OPERATION TYPE INDICATES THE TYPE OF SHUTOFF OPERATION PROVIDED. SELECT REPLY CODE 10AE36 BJRTD /D/ 07TAILPIECE,CONNECTION,SUPPLY SUPPLY CONNECTION TAILPIECE AN INDICATION OF WHETHER OR NOT A SUPPLY CONNECTION TAILPIECE IS INCLUDED. SELECT REPLY CODE 10AA49 BJRWD 18TYPE,TAILPIECE,SUPPLY CONNECTION SUPPLY CONNECTION TAILPIECE TYPE INDICATES THE TYPE OF SUPPLY CONNECTION TAILPIECE PROVIDED. SELECT REPLY CODE 10AK54 BJRXJ 03DESIGNATION,PIPE SIZE,NOMINAL,SUPPLY CONNECTION SUPPLY CONNECTION NOMINAL PIPE SIZE DESIGNATION THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE DIAMETER OF THE SUPPLY CONNECTION PIPE. 1D AND 1B MODE REPLY11AA05 BJRYD /D/ 07NUT,UNION,SUPPLY CONNECTION SUPPLY CONNECTION UNION NUT AN INDICATION OF WHETHER OR NOT THE SUPPLY CONNECTION INCLUDES A UNION NUT(S). SELECT REPLY CODE 10AA49 BJRZD 18TYPE,CONNECTION,SUPPLY SUPPLY CONNECTION TYPE INDICATES THE TYPE OF SUPPLY CONNECTION PROVIDED. SELECT REPLY CODE 10AG81 BJSBJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CONNECTION,SUPPLY SUPPLY CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE SUPPLY CONNECTION. 1D AND 1A MODE REPLY12AH06 BJSCH /D/ 09MATERIAL AND LOCATION,CORE CORE MATERIAL AND LOCATION THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CORE IS FABRICATED,AND ITS LOCATION. 2D MODE REPLY 26AD093AJ91 BJSDD /D/ 07FRAME FRAME AN INDICATION OF WHETHER OR NOT A FRAME IS INCLUDED.PLEASE USE MRC CBBL IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 BJSFD 18TYPE,CORE CORE TYPE INDICATES THE TYPE OF CORE PROVIDED. SELECT REPLY CODE 10AK54 BJSGD 18TYPE,END,INLET CONNECTION INLET CONNECTION END TYPE INDICATES A NARRATIVE DESCRIPTION OF THE TYPE OF INLET END CONNECTION. SELECT REPLY CODE 10AB76 BJSHA 12QUANTITY,END,INLET CONNECTION INLET CONNECTION END QUANTITY THE NUMBER OF INLET CONNECTION ENDS PROVIDED. 1A MODE REPLY 0 BJSJD 14SHAPE,END,INLET CONNECTION INLET CONNECTION END SHAPE THE PHYSICAL CONFIGURATION OF THE INLET CONNECTION END/S/. SELECT REPLY CODE 10AD07 BJSKA 12QUANTITY,END,OUTLET CONNECTION OUTLET CONNECTION END QUANTITY THE NUMBER OF OUTLET CONNECTION ENDS PROVIDED. 1A MODE REPLY 0 BJSLD /D/ 14SHAPE,END,OUTLET CONNECTION OUTLET CONNECTION END SHAPE THE PHYSICAL CONFIGURATION OF THE OUTLET CONNECTION END/S/. SELECT REPLY CODE 10AD07 BJSMA 12QUANTITY,NECK,FILLER FILLER NECK QUANTITY THE NUMBER OF FILLER NECK(S) PROVIDED. 1A MODE REPLY 0 BJSND /D/ 07CASING,VALVE VALVE CASING AN INDICATION OF WHETHER OR NOT A VALVE CASING IS INCLUDED. SELECT REPLY CODE 10AA49 BJSPJ 10PRESSURE RATING,MAXIMUM,VALVE CASING VALVE CASING MAXIMUM PRESSURE RATING THE MAXIMUM PRESSURE AT WHICH THE VALVE CASING IS RATED. 1D AND 1B MODE REPLY12AG67 BJSQD /D/ 08LOCATION,CASING,VALVE VALVE CASING LOCATION INDICATES THE LOCATION OF THE VALVE CASING. SELECT REPLY CODE 10AJ91 BJSRD /D/ 07VALVE,CHECK,ELBOW,COOLANT LEVEL COOLANT LEVEL ELBOW CHECK VALVE AN INDICATION OF WHETHER OR NOT A COOLANT LEVEL ELBOW CHECK VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 BJSSD /D/ 07SHROUD,FAN FAN SHROUD AN INDICATION OF WHETHER OR NOT A FAN SHROUD IS INCLUDED. SELECT REPLY CODE 10AA49 BJSTD /D/ 07FEATURE,MOUNTING MOUNTING FEATURE AN INDICATION OF WHETHER OR NOT A MOUNTING FEATURE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BJSWJ 10FLOW RATE,OIL OIL FLOW RATE THE RATED CAPACITY OF OIL FLOW DISCHARGED BY THE ITEM. 1D AND 1B MODE REPLY12AL69 BJSXD 14SHAPE AT FERRULE,STOCK STOCK SHAPE AT FERRULE THE PHYSICAL CONFIGURATION OF THE STOCK AT THE FERRULE. SELECT REPLY CODE 10AD07 BJSYD /D/ 07VALVE,REGULATING,TEMP TEMP REGULATING VALVE AN INDICATION OF WHETHER OR NOT A TEMPERATURE REGULATING VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 BJSZD 14SHAPE,CORE CORE SHAPE THE PHYSICAL CONFIGURATION OF THE CORE. SELECT REPLY CODE 10AD07 BJTBJ 10AREA,FRONTAL,CORE CORE FRONTAL AREA A MEASUREMENT OF THE FRONTAL AREA OF THE CORE. 1D AND 1B MODE REPLY12AG67 BJTCD /D/ 07FINS FINS AN INDICATION OF WHETHER OR NOT FINS ARE INCLUDED. SELECT REPLY CODE 10AA49 BJTDD 14SHAPE,INCLOSURE INCLOSURE SHAPE THE PHYSICAL CONFIGURATION OF THE INCLOSURE. SELECT REPLY CODE 10AD07 BJTFD /D/ 09MATERIAL,INCLOSURE INCLOSURE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INCLOSURE IS FABRICATED. SELECT REPLY CODE 10AD09 BJTGD 18TYPE,DRAIN,INCLOSURE INCLOSURE DRAIN TYPE INDICATES THE TYPE OF INCLOSURE DRAIN. SELECT REPLY CODE 10AN22 BJTHA 12QUANTITY,INLET INLET QUANTITY THE NUMBER OF INLET(S) PROVIDED. 1A MODE REPLY 0 BJTJJ 04DIAMETER,CIRCLE,BOLT HOLE BOLT HOLE CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT HOLE CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BJTKA 12QUANTITY,HOLE,OUTLET CONNECTION BOLT OUTLET CONNECTION BOLT HOLE QUANTITY THE NUMBER OF BOLT HOLES PROVIDED IN THE OUTLET CONNECTION. 1A MODE REPLY 0 BJTLJ 04DIAMETER,HOLE,BOLT,OUTLET CONNECTION OUTLET CONNECTION BOLT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN OUTLET CONNECTION BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BJTMJ 04DIAMETER,CIRCLE,BOLT HOLE,CONNECTION,OUTLET OUTLET CONNECTION BOLT HOLE CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN OUTLET CONNECTION BOLT HOLE CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BJTNJ 04DIAMETER,OUTSIDE,OUTLET CONNECTION OUTLET CONNECTION OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN OUTLET CONNECTION,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BJTPD 13THREAD LOCATION,CONNECTION,OUTLET OUTLET CONNECTION THREAD LOCATION THE PORTION OF THE OUTLET CONNECTION ON WHICH THE THREAD IS LOCATED. SELECT REPLY CODE 10AJ91 BJTQA 13THREAD SIZE,CONNECTION,OUTLET OUTLET CONNECTION THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE THREADED OUTLET CONNECTION. 1A MODE REPLY 0 BJTRD /D/ 07OPENING,VALVE,TEMP REGULATING TEMP REGULATING VALVE OPENING AN INDICATION OF WHETHER OR NOT AN OPENING IS INCLUDED FOR A TEMPERATURE REGULATING VALVE. SELECT REPLY CODE 10AA49 BJTSD /D/ 09MATERIAL,STOCK STOCK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE STOCK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BJTTJ 10PERCENTAGE,BRISTLE,HOG HOG BRISTLE PERCENTAGE THE PERCENTAGE OF HOG BRISTLE IN THE ITEM. 1D AND 1B MODE REPLY11AC20 BJTWJ 04LENGTH,EXPOSED,STOCK STOCK EXPOSED LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE EXPOSED STOCK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BJTXJ /D/ 19CHARACTERISTICS,PACKAGING,MULTIPLE UNIT MULTIPLE UNIT PACKAGING CHARACTERISTICS THE CHARACTERISTICS THAT ARE INCLUDED IN A MULTIPLE UNIT PACKAGE. 3D AND 1B MODE REPLY32AG674AE962AB49 BJTYD /D/ 07EDGE,ANGULAR ANGULAR EDGE AN INDICATION OF WHETHER OR NOT AN ANGULAR EDGE IS INCLUDED. SELECT REPLY CODE 10AA49 BJTZD /D/ 09MATERIAL,FERRULE FERRULE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FERRULE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BJWBD /D/ 07STAND STAND AN INDICATION OF WHETHER OR NOT A STAND IS INCLUDED. SELECT REPLY CODE 10AA49 BJWCD /D/ 07ARBOR ARBOR AN INDICATION OF WHETHER OR NOT AN ARBOR IS INCLUDED. SELECT REPLY CODE 10AA49 BJWDG 03DESIGNATION,SIZE,ATTACHMENT ATTACHMENT SIZE DESIGNATION THE SIZE DESIGNATION BY WHICH THE ATTACHMENT IS IDENTIFIED. FULL TEXT WRITE-IN 0 BJWFJ 10SIZE ACCOMMODATED,TOOL TOOL SIZE ACCOMMODATED DESIGNATES THE TOOL SIZE THAT THE ITEM WILL ACCOMMODATE. 2D AND 1B MODE REPLY21AA051AC20 BJWGA 12QUANTITY,JAW JAW QUANTITY THE NUMBER OF JAWS PROVIDED. 1A MODE REPLY 0 BJWHD /D/ 07JAW,REVERSIBLE REVERSIBLE JAW AN INDICATION OF WHETHER OR NOT A REVERSIBLE JAW/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 BJWJD /D/ 08LOCATION,HOLDING,WORK WORK HOLDING LOCATION INDICATES THE LOCATION AT WHICH THE WORK IS HELD BY THE ITEM. SELECT REPLY CODE 10AJ91 BJWKD /D/ 07JAWS WITH REVERSIBLE TOPS,TWO-PIECE TWO-PIECE JAWS WITH REVERSIBLE TOPS AN INDICATION OF WHETHER OR NOT TWO-PIECE JAWS WITH REVERSIBLE TOPS ARE INCLUDED. SELECT REPLY CODE 10AA49 BJWLD /D/ 07HOLE,CENTER,OBSTRUCTED OBSTRUCTED CENTER HOLE AN INDICATION OF WHETHER OR NOT AN OBSTRUCTED CENTER HOLE IS PROVIDED. SELECT REPLY CODE 10AB22 BJWMD /D/ 07FEATURE,DESIGN,ROTARY TABLE ROTARY TABLE DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A ROTARY TABLE DESIGN FEATURE IS PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AB22 BJWNJ 04DIAMETER,TABLE TABLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TABLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BJWPD /D/ 07FACEPLATE FACEPLATE AN INDICATION OF WHETHER OR NOT A FACEPLATE IS PROVIDED. SELECT REPLY CODE 10AB22 BJWQD /D/ 07FINISH,HARDENED/GROUND HARDENED/GROUND FINISH AN INDICATION OF WHETHER OR NOT A HARDENED AND GROUND FINISH IS PROVIDED. SELECT REPLY CODE 10AB22 BJWRJ T10RANGE,EXPANSION EXPANSION RANGE A MEASUREMENT TAKEN FROM THE NORMAL STATE TO THE EXPANDED MAXIMUM SIZE OF THE ITEM. 1D AND 1F MODE REPLY11AA05 BJWSG 04SIZE,TAPER,MANDREL MANDREL TAPER SIZE THE DIMINISHING MEASUREMENT OF THE DIAMETER ALONG THE MAJOR AXIS OF THE MANDREL. FULL TEXT WRITE-IN 0 BJWTD /D/ 07CENTER,AUXILIARY AUXILIARY CENTER AN INDICATION OF WHETHER OR NOT AN AUXILIARY CENTER IS INCLUDED. SELECT REPLY CODE 10AA49 BJWWD /D/ 07FILLER,CORK CORK FILLER AN INDICATION OF WHETHER OR NOT A CORK FILLER IS INCLUDED. SELECT REPLY CODE 10AA49 BJWXA /D/ 16STYLE DESIGNATOR,HOLDER HOLDER STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HOLDER. 1A MODE REPLY 0 BJWYD 19CLASS,GRIT GRIT CLASS AN INDICATION OF THE CLASS OF GRIT PROVIDED. SELECT REPLY CODE 10AF67 BJWZD 18TYPE,BOND,ABRASIVE ABRASIVE BOND TYPE INDICATES THE TYPE OF ABRASIVE BOND PROVIDED. SELECT REPLY CODE 10AK39 BJXBJ 04LENGTH,OVERALL,HOLDER HOLDER OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BJXCJ 04WIDTH,OVERALL,HOLDER HOLDER OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BJXDJ 04HEIGHT,CHANNEL,MINOR MINOR CHANNEL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BJXFJ 04HEIGHT,CHANNEL,MAJOR MAJOR CHANNEL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BJXGD 18TYPE,HOLDER HOLDER TYPE INDICATES THE TYPE OF HOLDER PROVIDED. SELECT REPLY CODE 10AK54 BJXHD /D/ 07FEATURE,TYPE,SPRING SPRING TYPE FEATURE AN INDICATION OF WHETHER OR NOT A SPRING TYPE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BJXJD 19TOOL ACCOMMODATED,CUTTER CUTTER TOOL ACCOMMODATED AN INDICATION OF THE CUTTING TOOL THE ITEM IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AK95 BJXKD 14SHAPE,TOOL,CUTTING CUTTING TOOL SHAPE THE PHYSICAL CONFIGURATION OF THE CUTTING TOOL. SELECT REPLY CODE 10AL59 BJXLJ T04DIAMETER RANGE,CUTTER CUTTER DIAMETER RANGE THE MINIMUM AND MAXIMUM DIAMETER LIMITS OF THE CUTTER. 1D AND 1F MODE REPLY11AA05 BJXMD /D/ 18TYPE FOR WHICH DESIGNED,DRIVE,CUTTER CUTTER DRIVE TYPE FOR WHICH DESIGNED INDICATES THE CUTTER DRIVE TYPE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BJXND /D/ 07PUMP,HYDRAULIC HYDRAULIC PUMP AN INDICATION OF WHETHER OR NOT A HYDRAULIC PUMP IS INCLUDED. PLEASE USE MRC PRJK IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BJXPJ 04DEPTH,JAW JAW DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE JAW,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BJXQJ 04LENGTH,OVERALL,JAW JAW OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE JAW. 2D AND 1B MODE REPLY21AA051AC20 BJXRJ 10OPENING,MAXIMUM,JAW JAW MAXIMUM OPENING A MEASUREMENT OF THE MAXIMUM OPENING BETWEEN THE JAWS. 1D AND 1B MODE REPLY11AA05 BJXSD 19POSITION,GROOVE,JAW JAW GROOVE POSITION INDICATES THE POSITION OF THE GROOVE(S) IN THE JAW(S). SELECT REPLY CODE 10AC60 BJXTG 19DEGREE IN EACH PLANE,ADJUSTMENT,BASE BASE ADJUSTMENT DEGREE IN EACH PLANE A MEASUREMENT OF THE DEGREE OF ADJUSTMENT FOR THE BASE IN EACH PLANE. FULL TEXT WRITE-IN 0 BJXWD /D/ 07PROVISION,SECURING,BASE TO MACHINE BASE TO MACHINE SECURING PROVISION AN INDICATION OF WHETHER OR NOT A BASE TO MACHINE SECURING PROVISION/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 BJXXJ 04HEIGHT,CONTRACTED CONTRACTED HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE ITEM WHEN FULLY CONTRACTED,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BJXYD /D/ 07FEATURE,GROUND GROUND FEATURE AN INDICATION OF WHETHER OR NOT A GROUND FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BJXZA 12QUANTITY PER SET,BLOCK BLOCK QUANTITY PER SET THE NUMBER OF BLOCK(S) PER SET. 1A MODE REPLY 0 BJYBB 04ANGLE IN DEG,THROW THROW ANGLE IN DEG THE ANGLE OF THROW,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BJYCD /D/ 07FITTING,CONNECTION CONNECTION FITTING AN INDICATION OF WHETHER OR NOT A CONNECTION FITTING IS INCLUDED. SELECT REPLY CODE 10AA49 BJYDJ 04LENGTH,SHAFT,ACTUATING ACTUATING SHAFT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ACTUATING SHAFT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BJYFJ 04DIAMETER,LARGEST,ACTUATING SHAFT ACTUATING SHAFT LARGEST DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST PORTION OF AN ACTUATING SHAFT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BJYGD 18TYPE,CONNECTION,ACTUATING SHAFT END ACTUATING SHAFT END CONNECTION TYPE INDICATES THE TYPE OF END CONNECTION PROVIDED ON THE ACTUATING SHAFT. SELECT REPLY CODE 10AB76 BJYHD 14SHAPE,SERRATION SERRATION SHAPE THE PHYSICAL CONFIGURATION OF THE SERRATIONS. SELECT REPLY CODE 10AD07 BJYJD 07PROVISION,THREAD,MOUNTING HOLE MOUNTING HOLE THREAD PROVISION AN INDICATION OF WHETHER OR NOT THE MOUNTING HOLE IS THREADED. SELECT REPLY CODE 10AE00 BJYKD /D/ 13THREAD SERIES DESIGNATOR,HOLE,MOUNTING MOUNTING HOLE THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATIONS APPLIED TO A MOUNTING HOLE. SELECT REPLY CODE 10AH06 BJYLA 13THREAD SIZE,SLEEVE SLEEVE THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED SLEEVE. 1A MODE REPLY 0 BJYMD 13THREAD SERIES DESIGNATOR,SLEEVE SLEEVE THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATIONS APPLIED TO A SLEEVE. SELECT REPLY CODE 10AH06 BJYND 13THREAD DIRECTION,SLEEVE SLEEVE THREAD DIRECTION THE DIRECTION OF THE SLEEVE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 BJYPD /D/ 07FEATURE,PAINTED PAINTED FEATURE AN INDICATION OF WHETHER OR NOT A PAINTED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BJYQD /D/ 07EXTENSION,ADAPTER,DRIVE DRIVE ADAPTER EXTENSION AN INDICATION OF WHETHER OR NOT A DRIVE ADAPTER EXTENSION IS INCLUDED. SELECT REPLY CODE 10AA49 BJYRD 18TYPE,EXTENSION,DRIVE ADAPTER DRIVE ADAPTER EXTENSION TYPE INDICATES THE TYPE OF DRIVE ADAPTER EXTENSION ON THE ITEM. SELECT REPLY CODE 10AL80 BJYSD 11METHOD,MOUNTING,BLADE BLADE MOUNTING METHOD THE MEANS PROVIDED FOR MOUNTING THE BLADE. SELECT REPLY CODE 10AM39 BJYTD 18TYPE,MOUNTING,DRIVE END DRIVE END MOUNTING TYPE INDICATES THE TYPE OF MOUNTING ON THE DRIVE END OF AN ITEM. SELECT REPLY CODE 10AM39 BJYWD /D/ 07HOLE,MOUNTING,DRIVE SHAFT,DRIVE END DRIVE END DRIVE SHAFT MOUNTING HOLE AN INDICATION OF WHETHER OR NOT A DRIVE END DRIVE SHAFT MOUNTING HOLE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BJYXD /D/ 07DEVICE,LOCKING,DRIVE END DRIVE END LOCKING DEVICE AN INDICATION OF WHETHER OR NOT A LOCKING DEVICE FOR THE DRIVE END IS INCLUDED. SELECT REPLY CODE 10AA49 BJYYD /D/ 07ADAPTER,SHAFT,DRIVE DRIVE SHAFT ADAPTER AN INDICATION OF WHETHER OR NOT A DRIVE SHAFT ADAPTER(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BJYZD /D/ 07NUT,ADAPTER ADAPTER NUT AN INDICATION OF WHETHER OR NOT AN ADAPTER NUT IS INCLUDED. SELECT REPLY CODE 10AA49 BJZBA 13THREAD SIZE,NUT NUT THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED NUT. 1A MODE REPLY 0 BJZCD 18TYPE,RETAINER,INSERT INSERT RETAINER TYPE INDICATES THE TYPE OF INSERT RETAINER ON THE ITEM. SELECT REPLY CODE 10AH28 BJZDD 07REPLACEABILITY,INSERT INSERT REPLACEABILITY AN INDICATION OF WHETHER OR NOT THE INSERT IS REPLACEABLE. SELECT REPLY CODE 10AG84 BJZFD /D/ 07ADAPTER,ARM,WIPER WIPER ARM ADAPTER AN INDICATION OF WHETHER OR NOT A WIPER ARM ADAPTER(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BJZGD /D/ 09MATERIAL,COVER,OUTER OUTER COVER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE OUTER COVER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BJZHD /D/ 07COATING ON ONE SIDE,ADHESIVE,PRESSURE SENSITIVE PRESSURE SENSITIVE ADHESIVE COATING ON ONE SIDE AN INDICATION OF WHETHER OR NOT A PRESSURE SENSITIVE ADHESIVE COATING ON ONE SIDE IS INCLUDED. SELECT REPLY CODE 10AA49 BJZJA /D/ 12QUANTITY PER SLIDE,PANEL PANEL QUANTITY PER SLIDE THE NUMBER OF PANEL(S) PER SLIDE. 1A MODE REPLY 0 BJZKA 12QUANTITY,LINE,PRINT PRINT LINE QUANTITY THE NUMBER OF PRINT LINE(S) PROVIDED. 1A MODE REPLY 0 BJZLD 18TYPE,SLIDE SLIDE TYPE INDICATES THE TYPE OF SLIDE PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AM39 BJZMG /D/ 19SYMBOL/DEVICE AND SIZE SYMBOL/DEVICE AND SIZE AN INDICATION OF THE SYMBOL AND/OR DEVICE AND ITS SIZE. FULL TEXT WRITE-IN 0 BJZNJ 04HEIGHT,CHARACTER CHARACTER HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE CHARACTER(S),IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BJZPJ 04HEIGHT,SYMBOL SYMBOL HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE SYMBOL(S),IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BJZQJ A10CAPACITY,LATERAL,SLIDE SLIDE LATERAL CAPACITY THE LATERAL CAPACITY OF THE SLIDE. 1D AND 1A MODE REPLY13AK54 BJZRA /D/ 12QUANTITY FOR WHICH DESIGNED,EQUIPMENT EQUIPMENT QUANTITY FOR WHICH DESIGNED THE NUMBER OF EQUIPMENT FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 BJZSA 12QUANTITY,SLOT,BACK PANEL BACK PANEL SLOT QUANTITY THE NUMBER OF SLOT(S) PROVIDED IN THE BACK PANEL. 1A MODE REPLY 0 BJZTJ /D/A10CAPACITY,SLIDE/PANEL SLIDE/PANEL CAPACITY THE CAPACITY OF THE SLIDE AND/OR PANEL. 2D AND 1A MODE REPLY23AK541AC20 BJZWD /D/ 07BORDER BORDER AN INDICATION OF WHETHER OR NOT A BORDER IS INCLUDED. SELECT REPLY CODE 10AA49 BJZXG /D/ 19SIZE/CHARACTER-SYMBOL AND QUANTITY,STENCIL STENCIL SIZE/CHARACTER-SYMBOL AND QUANTITY DESIGNATES THE SIZE,CHARACTER,AND/OR SYMBOL,AND NUMBER OF STENCIL(S) PROVIDED. FULL TEXT WRITE-IN 0 BJZYD 07REMOVABILITY,SLIDE SLIDE REMOVABILITY AN INDICATION OF WHETHER OR NOT THE SLIDE IS REMOVABLE. SELECT REPLY CODE 10AC29 BJZZD /D/ 07CONTAINER,FILE,INDEX INDEX FILE CONTAINER AN INDICATION OF WHETHER OR NOT AN INDEX FILE CONTAINER IS PROVIDED. SELECT REPLY CODE 10AB22 BKBBJ 04DISTANCE,CENTER OF CAP TO CAM END CENTER OF CAP TO CAM END DISTANCE THE DISTANCE FROM THE CENTER OF THE CAP TO THE END OF THE CAM. 1D AND 1B MODE REPLY11AA05 BKBCJ 04DIAMETER,PLATE,GUIDE GUIDE PLATE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A GUIDE PLATE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BKBDJ 04DIAMETER,OUTSIDE,BULB TIP BULB TIP OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BKBFD 19INSCRIPTION,SCALE SCALE INSCRIPTION THE INSCRIPTION AFFIXED TO OR STAMPED ON THE SCALE,EXCLUDING PART NUMBER. SELECT REPLY CODE 10AD21 BKBGD /D/ 07MATERIAL,FILTER,BREATHER BREATHER FILTER MATERIAL AN INDICATION OF WHETHER OR NOT BREATHER FILTER MATERIAL IS PROVIDED. SELECT REPLY CODE 10AB22 BKBHJ T10RANGE,PRESSURE,OPERATING OPERATING PRESSURE RANGE THE MINIMUM TO MAXIMUM PRESSURE FOR WHICH THE ITEM IS DESIGNED TO OPERATE. 1D AND 1F MODE REPLY12AJ20 BKBJD 18TYPE FOR WHICH DESIGNED,FLUID FLUID TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF FLUID FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AB75 BKBKD /D/ 07CONNECTION,PRESSURE,DIRECT,THREADED THREADED DIRECT PRESSURE CONNECTION AN INDICATION OF WHETHER OR NOT A THREADED DIRECT PRESSURE CONNECTION IS PROVIDED. SELECT REPLY CODE 10AB22 BKBLD 18TYPE,CONNECTION,TUBE TUBE CONNECTION TYPE INDICATES THE TYPE OF TUBE CONNECTION PROVIDED. SELECT REPLY CODE 10AJ68 BKBMD 18TYPE,CONNECTION,GAGE END GAGE END CONNECTION TYPE INDICATES THE TYPE OF GAGE END CONNECTION PROVIDED. SELECT REPLY CODE 10AJ68 BKBND /D/ 07PISTON,REMOVABLE REMOVABLE PISTON AN INDICATION OF WHETHER OR NOT A REMOVABLE PISTON IS PROVIDED. SELECT REPLY CODE 10AB22 BKBPA 03DESIGNATION,SIZE,PISTON PISTON SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE PISTON IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1A MODE REPLY 0 BKBQA 03DESIGNATION,SIZE,ADDITIONAL PISTON ADDITIONAL PISTON SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE ADDITIONAL PISTON(S) IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1A MODE REPLY 0 BKBRD /D/ 09MATERIAL,INSULATION,INDIVIDUAL WIRE INDIVIDUAL WIRE INSULATION MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INDIVIDUAL WIRE INSULATION IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BKBSD /D/ 09MATERIAL,INSULATION/SHEATHING,OUTER JACKET OUTER JACKET INSULATION/SHEATHING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE OUTER JACKET INSULATION AND/OR SHEATHING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BKBTD /D/ 18TYPE,TUBE,PROTECTING PROTECTING TUBE TYPE INDICATES THE TYPE OF PROTECTING TUBE PROVIDED ON THE ITEM. SELECT REPLY CODE 10AA62 BKBWJ 04LENGTH,IMMERSION IMMERSION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE IMMERSED PORTION OF THE ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BKBXA 12QUANTITY,CHANNEL,RECORDING RECORDING CHANNEL QUANTITY THE NUMBER OF RECORDING CHANNELS PROVIDED. 1A MODE REPLY 0 BKBYF T10FREQUENCY RANGE IN HERTZ,RECORDING RECORDING FREQUENCY RANGE IN HERTZ THE MINIMUM AND MAXIMUM VALUES OF THE FREQUENCY RANGE AT WHICH THE ITEM WILL RECORD,EXPRESSED IN HERTZ. 1F MODE REPLY 0 BKBZB /D/ 10DEFLECTION PER VOLT IN MILLIMETERS,SENSITIVITY SENSITIVITY DEFLECTION PER VOLT IN MILLIMETERS THE AMOUNT OF RESPONSIVE DEPARTURE PER VOLT,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 BKCBJ 10SPEED,CHART CHART SPEED THE RATED SPEED AT WHICH THE CHART IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY12AG20 BKCCG /D/ 10FREQUENCY RANGE,DEFLECTION,AMPLITUDE AMPLITUDE DEFLECTION FREQUENCY RANGE THE MEASURED AMOUNT OF DEPARTURE FROM THE MEAN POSITION TO THE EXTREME AT A SPECIFIED FREQUENCY RANGE. FULL TEXT WRITE-IN 0 BKCDD /D/ 07MARKER,EVENT EVENT MARKER AN INDICATION OF WHETHER OR NOT AN EVENT MARKER(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BKCFA 13THREAD SIZE,MALE,SMALLEST SMALLEST MALE THREAD SIZE NONE. 1A MODE REPLY 0 BKCGJ 04LENGTH,TIP,BULB BULB TIP LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BKCHJ 04LENGTH,NECK,EXTENSION EXTENSION NECK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BKCJJ 04DIAMETER,NECK,EXTENSION EXTENSION NECK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BKCKD /D/ 07CAP AFFIXED W/CHAIN,BRASS,REMOVABLE REMOVABLE BRASS CAP AFFIXED W/CHAIN AN INDICATION OF WHETHER OR NOT A REMOVABLE BRASS CAP AFFIXED WITH A CHAIN IS PROVIDED. SELECT REPLY CODE 10AB22 BKCLD /D/ 19TEMP FOR WHICH DESIGNED,INDICATING INDICATING TEMP FOR WHICH DESIGNED THE INDICATING TEMPERATURE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BKCMD 19MEDIUM,ACTUATING ACTUATING MEDIUM AN INDICATION OF THE MEDIUM USED TO ACTUATE THE ITEM. SELECT REPLY CODE 10AB75 BKCNG 10ACCURACY RATING,SCALE SCALE ACCURACY RATING THE AMOUNT OF ACCURACY FOR WHICH THE SCALE IS RATED. FULL TEXT WRITE-IN 0 BKCPJ /D/ 04LENGTH,SCALE,DIAL DIAL SCALE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE DIAL SCALE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BKCQD 19VARIATION,ADJUSTMENT,SCALE SCALE ADJUSTMENT VARIATION AN INDICATION OF THE AMOUNT OF SCALE VARIATION ADJUSTMENT PROVIDED. SELECT REPLY CODE 10AD21 BKCRD /D/ 07FRONT,MAGNIFYING,LENS LENS MAGNIFYING FRONT AN INDICATION OF WHETHER OR NOT A LENS WITH A MAGNIFYING FRONT IS PROVIDED. SELECT REPLY CODE 10AB22 BKCSD 18TYPE,TIP,ARMOR ENCASED ARMOR ENCASED TIP TYPE INDICATES THE TYPE OF ARMOR ENCASED TIP PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AJ55 BKCTA 12QUANTITY,BULB BULB QUANTITY THE NUMBER OF BULBS PROVIDED. 1A MODE REPLY 0 BKCWD 18TYPE,BULB BULB TYPE INDICATES THE TYPE OF BULB PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AK39 BKCXD 18TYPE,CONNECTION,BULB BULB CONNECTION TYPE INDICATES THE TYPE OF BULB CONNECTION PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AB76 BKCYJ 04LENGTH,PORTION,ACTIVE ACTIVE PORTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ACTIVE PORTION OF AN ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BKCZJ 04DIAMETER,PORTION,ACTIVE ACTIVE PORTION DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACTIVE PORTION OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BKDBD 18TYPE,MATERIAL,STOCK STOCK MATERIAL TYPE INDICATES THE TYPE OF STOCK MATERIAL. SELECT REPLY CODE 10AN23 BKDCJ 04WIDTH AT FERRULE,STOCK STOCK WIDTH AT FERRULE A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE STOCK AT THE FERRULE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BKDDJ 04DIAMETER AT FERRULE,STOCK STOCK DIAMETER AT FERRULE THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE STOCK AT THE FERRULE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BKDFJ 04DIAMETER FOR WHICH DESIGNED,OUTSIDE,BOILER TUBE BOILER TUBE OUTSIDE DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOILER TUBE FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BKDGJ 04THICKNESS FOR WHICH DESIGNED,WALL,BOILER TUBE BOILER TUBE WALL THICKNESS FOR WHICH DESIGNED A MEASUREMENT OF THE SMALLEST DIMENSION OF THE BOILER TUBE WALL FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BKDHD /D/ 07HANDLE,FLEXIBLE FLEXIBLE HANDLE AN INDICATION OF WHETHER OR NOT A FLEXIBLE HANDLE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BKDJD /D/ 07FEATURE,OPERATING,POWER POWER OPERATING FEATURE AN INDICATION OF WHETHER OR NOT A POWER OPERATING FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BKDKD /D/ 07JOINT,UNIVERSAL UNIVERSAL JOINT AN INDICATION OF WHETHER OR NOT A UNIVERSAL JOINT IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BKDLD /D/ 09MATERIAL,PART,BRUSH BRUSH PART MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BRUSH PART IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. USE MRC MATT AND ISAC TO TABLE 0060. SELECT REPLY CODE 10AD09 BKDMJ 04LENGTH,EXPOSED,BRUSH MATERIAL BRUSH MATERIAL EXPOSED LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE EXPOSED BRUSH MATERIAL,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BKDNA 12QUANTITY ALONG WIDTH,ROW,BRUSH BRUSH ROW QUANTITY ALONG WIDTH THE NUMBER OF BRUSH ROWS ALONG THE WIDTH. 1A MODE REPLY 0 BKDPA 12QUANTITY ALONG LENGTH,ROW,BRUSH BRUSH ROW QUANTITY ALONG LENGTH THE NUMBER OF BRUSH ROWS ALONG THE LENGTH. 1A MODE REPLY 0 BKDQD /D/ 07FEATURE,SPARKPROOF SPARKPROOF FEATURE AN INDICATION OF WHETHER OR NOT A SPARKPROOF FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BKDRD 02DESIGN,SPIRAL SPIRAL DESIGN THE BASIC DESIGN OF THE SPIRAL. SELECT REPLY CODE 10AK54 BKDSJ 04DIAMETER,BRUSH PART BRUSH PART DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BRUSH PART,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BKDTJ 04LENGTH,PART,BRUSH BRUSH PART LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BRUSH PART,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BKDWD 01COLOR,BRUSH PART BRUSH PART COLOR THE HUE OR TINT OF THE BRUSH PART. SELECT REPLY CODE 10AD06 BKDXB 10PERCENTAGE,MATERIAL MATERIAL PERCENTAGE THE PERCENTAGE OF THE MATERIALS USED IN THE ITEM. 1B MODE REPLY 0 BKDYD 14SHAPE,BLOCK BLOCK SHAPE THE PHYSICAL CONFIGURATION OF THE BLOCK. SELECT REPLY CODE 10AD07 BKDZD /D/ 07PROVISION,HANDLE,DETACHABLE DETACHABLE HANDLE PROVISION AN INDICATION OF WHETHER OR NOT A DETACHABLE HANDLE PROVISION IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BKFBJ 10VOLTAGE IN VOLTS,OPERATING,EXTERNAL DC EXTERNAL DC OPERATING VOLTAGE IN VOLTS THE VALUE(S) OF THE POTENTIAL SUPPLIED FROM AN EXTERIOR DIRECT CURRENT SOURCE TO OPERATE THE ITEM,EXPRESSED IN VOLTS. 2D AND 1B MODE REPLY21AC202AD88 BKFCJ 10VOLTAGE IN VOLTS,OPERATING,EXTERNAL AC EXTERNAL AC OPERATING VOLTAGE IN VOLTS THE VALUE(S) OF THE POTENTIAL SUPPLIED FROM AN EXTERIOR ALTERNATING CURRENT SOURCE TO OPERATE THE ITEM,EXPRESSED IN VOLTS. 2D AND 1B MODE REPLY21AC202AD88 BKFDJ 04WIDTH,BRUSH PART BRUSH PART WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BRUSH PART,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BKFFD 19GRADE,BRISTLE BRISTLE GRADE AN INDICATION OF THE GRADE OF THE BRISTLE ON THE ITEM. SELECT REPLY CODE 10AN24 BKFGD /D/ 09MATERIAL,BRISTLE BRISTLE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BRISTLE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BKFHJ 04LENGTH,BRISTLE BRISTLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BRISTLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BKFJD /D/ 07FERRULE,METAL METAL FERRULE AN INDICATION OF WHETHER OR NOT A METAL FERRULE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BKFKL /D/ 16STYLE DESIGNATOR,BRUSH,DAUBER DAUBER BRUSH STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE DAUBER BRUSH. 1L MODE REPLY 0 BKFLD /D/ 09MATERIAL,PART,BRUSH,DAUBER DAUBER BRUSH PART MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE DAUBER BRUSH PART IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BKFMJ /D/ 04LENGTH,EXPOSED,DAUBER BRUSH MATERIAL DAUBER BRUSH MATERIAL EXPOSED LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE EXPOSED DAUBER BRUSH MATERIAL,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BKFNJ /D/ 04DIAMETER,BLOCK,DAUBER DAUBER BLOCK DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A DAUBER BLOCK, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BKFPJ /D/ 04LENGTH,OVERALL,DAUBER BLOCK DAUBER BLOCK OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE DAUBER BLOCK. 2D AND 1B MODE REPLY21AA051AC20 BKFQL /D/ 16STYLE DESIGNATOR,BRUSH,POLISHER POLISHER BRUSH STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGUARTION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE POLISHER BRUSH. 1L MODE REPLY 0 BKFRD /D/ 09MATERIAL,PART,BRUSH,POLISHER POLISHER BRUSH PART MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE POLISHER BRUSH PART IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BKFSJ /D/ 04LENGTH,EXPOSED,POLISHER BRUSH MATERIAL POLISHER BRUSH MATERIAL EXPOSED LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE EXPOSED POLISHER BRUSH MATERIAL,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BKFTJ /D/ 04LENGTH,BLOCK,POLISHER POLISHER BLOCK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE POLISHER BLOCK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BKFWJ /D/ 04WIDTH,BLOCK,POLISHER POLISHER BLOCK WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE POLISHER BLOCK,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BKFXD 18TYPE,BRUSH BRUSH TYPE INDICATES THE TYPE OF BRUSH PROVIDED. SELECT REPLY CODE 10AN25 BKFYJ 04LENGTH,OVERALL,BLOCK BLOCK OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BLOCK. 2D AND 1B MODE REPLY21AA051AC20 BKFZG /D/ 10CAPACITY,LOADING,FILM FILM LOADING CAPACITY THE FILM LOADING CAPACITY OF THE ITEM. FULL TEXT WRITE-IN 0 BKGBD /D/ 07DRIER DRIER AN INDICATION OF WHETHER OR NOT A DRIER IS INCLUDED. SELECT REPLY CODE 10AA49 BKGCJ 10TIME,PROCESSING PROCESSING TIME THE TIME REQUIRED FOR PROCESSING THE ITEM. 2D AND 1B MODE REPLY22AG671AD93 BKGDD /D/ 07CONVERSION,HEAT,GAS GAS HEAT CONVERSION AN INDICATION OF WHETHER OR NOT A PROVISION TO CONVERT TO GAS HEAT IS PROVIDED. SELECT REPLY CODE 10AB22 BKGFA 12QUANTITY,TANK,REPLENISHER SOLUTION REPLENISHER SOLUTION TANK QUANTITY THE NUMBER OF REPLENISHER SOLUTION TANKS FURNISHED WITH THE ITEM. 1A MODE REPLY 0 BKGGD /D/ 07PUMP,SOLUTION,INTEGRAL REPLENISHER INTEGRAL REPLENISHER SOLUTION PUMP AN INDICATION OF WHETHER OR NOT AN INTEGRAL REPLENISHER SOLUTION PUMP IS INCLUDED. SELECT REPLY CODE 10AA49 BKGHG 10SPEED,PROCESSING PROCESSING SPEED AN INDICATION OF THE SPEED AT WHICH AN ITEM MAY BE PROCESSED. FULL TEXT WRITE-IN 0 BKGJG 10CAPACITY,DRYING DRYING CAPACITY THE DRYING CAPACITY OF THE ITEM. FULL TEXT WRITE-IN 0 BKGKA 12QUANTITY,ELEMENT,HEATING HEATING ELEMENT QUANTITY THE NUMBER OF HEATING ELEMENTS PROVIDED ON THE ITEM. 1A MODE REPLY 0 BKGLA 12QUANTITY,TANK,PROCESSING PROCESSING TANK QUANTITY THE NUMBER OF PROCESSING TANKS INCLUDED WITH THE ITEM. 1A MODE REPLY 0 BKGMD /D/ 07FEATURE,NESTING NESTING FEATURE AN INDICATION OF WHETHER OR NOT A NESTING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BKGNJ /D/ 10CAPACITY,CONTAINER,LIQUID LIQUID CONTAINER CAPACITY AN INDICATION OF THE LIQUID CAPACITY OF THE CONTAINER. 1D AND 1B MODE REPLY12AG67 BKGPG 19TITLE/DATE OF ACCESSORIES AND COMPONENTS,DOCUMENT DOCUMENT TITLE/DATE OF ACCESSORIES AND COMPONENTS THE NAME AND DATE DESIGNATION OF THE PRINTED DOCUMENT/S/ OF ACCESSORIES AND COMPONENTS. FULL TEXT WRITE-IN 0 BKGQD 18TYPE,SPLICE SPLICE TYPE INDICATES THE TYPE OF SPLICE PROVIDED. SELECT REPLY CODE 10AK54 BKGRJ 10VOLTAGE RATING,ELEMENT,HEATING HEATING ELEMENT VOLTAGE RATING THE VOLTAGE VALUE FOR WHICH THE HEATING ELEMENT IS RATED. 2D AND 1B MODE REPLY21AB631AC20 BKGSD 18TYPE,AGENT,BONDING BONDING AGENT TYPE INDICATES THE TYPE OF BONDING AGENT PROVIDED. SELECT REPLY CODE 10AK54 BKGTD 11METHOD,REDUCING,LIGHT INTENSITY LIGHT INTENSITY REDUCING METHOD THE MEANS USED TO REDUCE THE INTENSITY OF LIGHT TRANSMITTED. SELECT REPLY CODE 10AN26 BKGWJ 10CAPACITY,REEL REEL CAPACITY THE AMOUNT OF MATERIAL THE REEL WILL ACCOMMODATE. 2D AND 1B MODE REPLY21AA051AC20 BKGXD 18TYPE,PLATEN PLATEN TYPE INDICATES THE TYPE OF PLATEN PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AC58 BKGYD /D/ 18TYPE FOR WHICH DESIGNED,MATERIAL MATERIAL TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF MATERIAL FOR WHICH THE ITEM IS DESIGNED. PLEASE USE MRC CBJH IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AN27 BKGZD /D/ 07FEATURE,PRINTING,COLOR COLOR PRINTING FEATURE AN INDICATION OF WHETHER OR NOT A COLOR PRINTING FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BKHBD /D/ 07CONTROL,EXPOSURE,AUTOMATIC AUTOMATIC EXPOSURE CONTROL AN INDICATION OF WHETHER OR NOT AN AUTOMATIC EXPOSURE CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 BKHCD 11METHOD,VIEWING VIEWING METHOD THE MEANS PROVIDED FOR VIEWING. SELECT REPLY CODE 10AK54 BKHDJ 04LENGTH,FOCAL,NOMINAL,FRONT COMPONENT FRONT COMPONENT NOMINAL FOCAL LENGTH A MEASUREMENT OF THE LONGEST NOMINAL FOCAL DIMENSION OF THE FRONT COMPONENT,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BKHFJ 04LENGTH,FOCAL,LENS LENS FOCAL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION FROM THE CENTER OF A LENS TO THE FOCAL PLANE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BKHGG /D/ 10SPEED FOR WHICH DESIGNED,LENS LENS SPEED FOR WHICH DESIGNED AN INDICATION OF THE LENS SPEED FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 BKHHG /D/ 19SYSTEM,DIFFUSION/CONDENSER DIFFUSION/CONDENSER SYSTEM AN INDICATION OF THE DIFFUSION/CONDENSER SYSTEM PROVIDED. FULL TEXT WRITE-IN 0 BKHJD /D/ 19ACCESSORY,PRINTING,VARIABLE CONTRAST PAPER VARIABLE CONTRAST PAPER PRINTING ACCESSORY THE ACCESSORY/IES/ SUPPLIED WITH THE ITEM TO FACILITATE THE PRINTING OF VARIABLE CONTRAST PAPER/S/. SELECT REPLY CODE 10AC58 BKHKG 04SIZE,HOLDER,FILM FILM HOLDER SIZE DESIGNATES THE SIZE OF THE FILM HOLDER PROVIDED WITH THE ITEM. FULL TEXT WRITE-IN 0 BKHLG /D/ 19ITEM,ADJUSTABLE ADJUSTABLE ITEM AN INDICATION OF THE ADJUSTABLE ITEM/S/ INCLUDED. FULL TEXT WRITE-IN 0 BKHMJ 10SPEED,PRINTING PRINTING SPEED THE RATE OF SPEED THE ITEM WILL PRINT. 1D AND 1B MODE REPLY12AG20 BKHNA 12QUANTITY,LAMP,SAFELIGHT SAFELIGHT LAMP QUANTITY THE NUMBER OF SAFELIGHT LAMP(S) INCLUDED WITH THE ITEM. 1A MODE REPLY 0 BKHPD 18TYPE,LAMP,SAFELIGHT SAFELIGHT LAMP TYPE INDICATES THE TYPE OF SAFELIGHT LAMP PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AD48 BKHQB 10WATTAGE IN WATTS,LAMP,SAFELIGHT SAFELIGHT LAMP WATTAGE IN WATTS THE RATED POWER THAT A SAFELIGHT LAMP CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS. 1B MODE REPLY 0 BKHRA 12QUANTITY,LAMP,SCANNING SCANNING LAMP QUANTITY THE NUMBER OF SCANNING LAMP(S) INCLUDED WITH THE ITEM. 1A MODE REPLY 0 BKHSD 18TYPE,LAMP,SCANNING SCANNING LAMP TYPE INDICATES THE TYPE OF SCANNING LAMP(S) PROVIDED. SELECT REPLY CODE 10AD48 BKHTB 10WATTAGE IN WATTS,LAMP,SCANNING SCANNING LAMP WATTAGE IN WATTS THE RATED POWER THAT A SCANNING LAMP CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS. 1B MODE REPLY 0 BKHWJ /D/ 04WIDTH AND LOCATION,MAXIMUM MAXIMUM WIDTH AND LOCATION THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ITEM,IN DISTINCTION FROM THICKNESS,AND ITS LOCATION. 2D AND 1B MODE REPLY21AA053AJ91 BKHXJ /D/ 04LENGTH AND LOCATION,MAXIMUM MAXIMUM LENGTH AND LOCATION THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF THE ITEM,IN DISTINCTION FROM WIDTH,AND ITS LOCATION. 2D AND 1B MODE REPLY21AA053AJ91 BKHYJ 04HEIGHT,MAXIMUM,PICTURE PICTURE MAXIMUM HEIGHT THE MAXIMUM MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE PICTURE,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BKHZD /D/ 07FEATURE,CONVERTIBLE,FOCAL LENGTH FOCAL LENGTH CONVERTIBLE FEATURE AN INDICATION OF WHETHER OR NOT A FOCAL LENGTH CONVERTIBLE FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BKJBD /D/ 07DEVICE,CUTTING,PRESET PRESET CUTTING DEVICE AN INDICATION OF WHETHER OR NOT A PRESET CUTTING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 BKJCJ 04LENGTH,TAPE,DISPENSED DISPENSED TAPE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TAPE THE ITEM WILL DISPENSE. 2D AND 1B MODE REPLY21AA051AC20 BKJDD 07ADJUSTABILITY,CONTROL,MOISTURE MOISTURE CONTROL ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE MOISTURE CONTROL IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BKJFD 18TYPE,LEGEND LEGEND TYPE INDICATES THE TYPE OF LEGEND PROVIDED. SELECT REPLY CODE 10AK54 BKJGA 12QUANTITY,STRIP STRIP QUANTITY THE NUMBER OF INDIVIDUAL STRIP(S) PROVIDED. 1A MODE REPLY 0 BKJHJ 04LENGTH,OVERALL,STRIP STRIP OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE STRIP. 2D AND 1B MODE REPLY21AA051AC20 BKJJJ 04LENGTH,STRIP,VISIBLE VISIBLE STRIP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE VISIBLE STRIP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BKJKJ 04WIDTH,STRIP STRIP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE STRIP,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BKJLD 08LOCATION,MARGIN,RULED RULED MARGIN LOCATION INDICATES THE PHYSICAL LOCATION OF THE RULED MARGIN. SELECT REPLY CODE 10AJ91 BKJMD 02DESIGN,MARGIN MARGIN DESIGN THE DESIGN OF THE MARGIN. SELECT REPLY CODE 10AK95 BKJND 18TYPE,PROJECTION PROJECTION TYPE INDICATES THE TYPE OF PROJECTION PROVIDED. SELECT REPLY CODE 10AK54 BKJPD 14SHAPE,PROJECTION PROJECTION SHAPE THE PHYSICAL CONFIGURATION OF THE PROJECTION. SELECT REPLY CODE 10AD07 BKJQD /D/ 07FEATURE,CUTOUT CUTOUT FEATURE AN INDICATION OF WHETHER OR NOT A CUTOUT FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BKJRA /D/ 12QUANTITY PER SET,STRIP/TAB STRIP/TAB QUANTITY PER SET THE NUMBER OF STRIP(S) OR TAB(S) PROVIDED PER SET. 1A MODE REPLY 0 BKJSD /D/ 07INSERTS,BLANK BLANK INSERTS AN INDICATION OF WHETHER OR NOT BLANK INSERTS ARE PROVIDED. SELECT REPLY CODE 10AB22 BKJTD 14SHAPE,HEAD HEAD SHAPE THE PHYSICAL CONFIGURATION OF THE HEAD. SELECT REPLY CODE 10AD07 BKJWJ 04SIZE,HEAD HEAD SIZE DESIGNATES THE SIZE OF THE HEAD. 1D AND 1B MODE REPLY11AA05 BKJXD /D/ 18TYPE,MARKING,HEAD HEAD MARKING TYPE INDICATES THE TYPE OF MARKING ON THE HEAD. SELECT REPLY CODE 10AH39 BKJYD /D/ 09MATERIAL,PIN PIN MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PIN IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BKJZD /D/ 07FEATURE,STAMP OUT,HEAD PIN HEAD PIN STAMP OUT FEATURE AN INDICATION OF WHETHER OR NOT A HEAD PIN STAMP OUT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BKKBD 14SHAPE,PERFORATION PERFORATION SHAPE THE PHYSICAL CONFIGURATION OF THE PERFORATION. SELECT REPLY CODE 10AD07 BKKCJ 04DIAMETER,DIE DIE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DIE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BKKDJ 10REACH TO THROAT END,CENTER,DIE DIE CENTER REACH TO THROAT END A MEASUREMENT TAKEN FROM THE CENTER OF THE DIE TO THE END OF THE THROAT. 2D AND 1B MODE REPLY21AA051AC20 BKKFD /D/ 07GAGE,THROAT,ADJUSTABLE ADJUSTABLE THROAT GAGE AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE THROAT GAGE IS INCLUDED. SELECT REPLY CODE 10AA49 BKKGJ 10CLEARANCE,FEED FEED CLEARANCE AN INDICATION OF THE AMOUNT OF FEED CLEARANCE PROVIDED BY THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BKKHA 19SYMBOL,IDENTIFYING,SCALE SCALE IDENTIFYING SYMBOL THE ALPHA/NUMERIC SYMBOL ASSIGNED TO THE SCALE FOR IDENTIFICATION. 1A MODE REPLY 0 BKKJG 03DESIGNATOR,SCALE SCALE DESIGNATOR THE ALPHA/NUMERIC SYMBOL USED TO DESIGNATE THE SCALES PROVIDED. FULL TEXT WRITE-IN 0 BKKKD /D/ 07MAGNIFIER,INDICATOR INDICATOR MAGNIFIER AN INDICATION OF WHETHER OR NOT AN INDICATOR MAGNIFIER IS INCLUDED. SELECT REPLY CODE 10AA49 BKKLD /D/ 07ARM,LEVER LEVER ARM AN INDICATION OF WHETHER OR NOT A LEVER ARM IS INCLUDED. SELECT REPLY CODE 10AA49 BKKMJ 04WIDTH,CROWN CROWN WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A CROWN,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BKKND /D/ 07ANVIL,ADJUSTABLE ADJUSTABLE ANVIL AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE ANVIL IS INCLUDED. SELECT REPLY CODE 10AA49 BKKPG 19MODEL FOR WHICH DESIGNED MODEL FOR WHICH DESIGNED THE MODEL FOR WHICH THE ITEM IS DESIGNED TO BE USED. FULL TEXT WRITE-IN 0 BKKQD /D/ 07FEATURE,SUITABILITY,TACKER USE TACKER USE SUITABILITY FEATURE AN INDICATION OF WHETHER OR NOT A TACKER USE SUITABILITY FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BKKRD /D/ 09MATERIAL,BED BED MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BED IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BKKSJ 04WIDTH ACCOMMODATED,MAXIMUM,PAPER PAPER MAXIMUM WIDTH ACCOMMODATED THE MAXIMUM WIDTH OF THE PAPER THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BKKTJ 04LENGTH ACCOMMODATED,MAXIMUM,PAPER PAPER MAXIMUM LENGTH ACCOMMODATED THE MAXIMUM LENGTH OF THE PAPER THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BKKWD /D/ 07GUIDE,TRIMMING,MOVABLE MOVABLE TRIMMING GUIDE AN INDICATION OF WHETHER OR NOT A MOVABLE TRIMMING GUIDE IS INCLUDED. SELECT REPLY CODE 10AA49 BKKXD 08LOCATION,LINE,GUIDE GUIDE LINE LOCATION INDICATES THE LOCATION OF THE GUIDE LINE(S). SELECT REPLY CODE 10AJ91 BKKYJ 04SPACING,LINE,GUIDE GUIDE LINE SPACING THE SPACING BETWEEN THE GUIDE LINES. 1D AND 1B MODE REPLY11AA05 BKKZJ 04DIAMETER,INSIDE,MINIMUM MINIMUM INSIDE DIAMETER THE SMALLEST LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ITEM,AND TERMINATES ON THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BKLBD 13THREAD SERIES,CONNECTION,SUPPLY SUPPLY CONNECTION THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATIONS AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF A THREADED OUTLET CONNECTION. SELECT REPLY CODE 10AH06 BKLCJ /D/ 04DISTANCE BETWEEN HOT/COLD SUPPLY CONNECTIONS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN HOT/COLD SUPPLY CONNECTIONS THE CENTER TO CENTER DISTANCE BETWEEN THE HOT AND COLD SUPPLY CONNECTIONS. 2D AND 1B MODE REPLY21AA051AC20 BKLDD 19FINISH,SURFACE,HANDLE HANDLE SURFACE FINISH AN ADDITIONAL FINISHING PROCESS BY WHICH THE SURFACE OF THE HANDLE IS ALTERED IN RESPECT TO POLISHING,GRINDING,AND THE LIKE. SELECT REPLY CODE 10AA41 BKLFD /D/ 07FLANGE FLANGE AN INDICATION OF WHETHER OR NOT A FLANGE IS PROVIDED. SELECT REPLY CODE 10AB22 BKLGD /D/ 07SPOUT,SWING SWING SPOUT AN INDICATION OF WHETHER OR NOT A SWING SPOUT IS PROVIDED. SELECT REPLY CODE 10AB22 BKLHD /D/ 07SPOUT,SWING,DOUBLE JOINTED DOUBLE JOINTED SWING SPOUT AN INDICATION OF WHETHER OR NOT A DOUBLE JOINTED SWING SPOUT IS PROVIDED. SELECT REPLY CODE 10AB22 BKLJD 18TYPE,SUPPORT,SPOUT SPOUT SUPPORT TYPE INDICATES THE TYPE OF SUPPORT PROVIDED FOR THE SPOUT. SELECT REPLY CODE 10AM61 BKLKD /D/ 07SPOUT,GOOSENECK GOOSENECK SPOUT AN INDICATION OF WHETHER OR NOT A GOOSENECK SPOUT IS PROVIDED. SELECT REPLY CODE 10AB22 BKLLD /D/ 07HOOK,PAIL PAIL HOOK AN INDICATION OF WHETHER OR NOT A PAIL HOOK IS PROVIDED. SELECT REPLY CODE 10AB22 BKLMD /D/ 07CONNECTION,HOSE,SPOUT SPOUT HOSE CONNECTION AN INDICATION OF WHETHER OR NOT A SPOUT HOSE CONNECTION IS PROVIDED. SELECT REPLY CODE 10AB22 BKLND 18TYPE,CONNECTION,SPOUT HOSE SPOUT HOSE CONNECTION TYPE INDICATES THE TYPE OF SPOUT HOSE CONNECTION PROVIDED. SELECT REPLY CODE 10AB76 BKLPD /D/ 18TYPE,TIP,SPOUT SPOUT TIP TYPE INDICATES THE TYPE OF SPOUT TIP PROVIDED. SELECT REPLY CODE 10AE98 BKLQD /D/ 07HOLDER,SOAP SOAP HOLDER AN INDICATION OF WHETHER OR NOT A SOAP HOLDER IS INCLUDED. SELECT REPLY CODE 10AA49 BKLRD /D/ 07DEVICE,CLAMP-ON,FIXTURE FIXTURE CLAMP-ON DEVICE AN INDICATION OF WHETHER OR NOT A FIXTURE CLAMP-ON DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 BKLSD /D/ 07HOSE/SPRAY HOSE/SPRAY AN INDICATION OF WHETHER OR NOT A HOSE OR SPRAY IS INCLUDED. SELECT REPLY CODE 10AA49 BKLTD /D/ 07CONNECTION,WATER,DRINKING,SEPARATE SEPARATE DRINKING WATER CONNECTION AN INDICATION OF WHETHER OR NOT A SEPARATE DRINKING WATER CONNECTION IS PROVIDED. SELECT REPLY CODE 10AB22 BKLWD /D/ 07PROVISIONS,MARKING MARKING PROVISIONS AN INDICATION OF WHETHER OR NOT MARKING PROVISIONS ARE INCLUDED. SELECT REPLY CODE 10AA49 BKLXD /D/ 07STRAINER,OPEN OPEN STRAINER AN INDICATION OF WHETHER OR NOT AN OPEN STRAINER IS INCLUDED. SELECT REPLY CODE 10AA49 BKLYG /D/ 04DIMENSION,STRAINER,OPEN OPEN STRAINER DIMENSION THE DIMENSION/S/ OF THE OPEN STRAINER. FULL TEXT WRITE-IN 0 BKLZD 11METHOD,FASTENING,SOLID COVER SOLID COVER FASTENING METHOD THE MEANS USED TO FASTEN THE SOLID COVER. SELECT REPLY CODE 10AB47 BKMBD /D/ 07FEATURE,DRAINAGE,DOUBLE DOUBLE DRAINAGE FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM IS DESIGNED TO PROVIDE FOR DOUBLE DRAINAGE. SELECT REPLY CODE 10AB22 BKMCD 18TYPE,TRAP,INTEGRAL INTEGRAL TRAP TYPE INDICATES THE TYPE OF INTEGRAL TRAP PROVIDED. SELECT REPLY CODE 10AD07 BKMDD /D/ 07RING,CLAMPING CLAMPING RING AN INDICATION OF WHETHER OR NOT A CLAMPING RING IS PROVIDED. SELECT REPLY CODE 10AB22 BKMFD /D/ 07VALVE,BACKWATER BACKWATER VALVE AN INDICATION OF WHETHER OR NOT A BACKWATER VALVE IS PROVIDED. SELECT REPLY CODE 10AB22 BKMGD /D/ 07FEATURE,CLEAN-OUT CLEAN-OUT FEATURE AN INDICATION OF WHETHER OR NOT A CLEAN-OUT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BKMHD /D/ 07BUCKET,REMOVABLE REMOVABLE BUCKET AN INDICATION OF WHETHER OR NOT A REMOVABLE BUCKET IS PROVIDED. SELECT REPLY CODE 10AB22 BKMJJ 04SIZE ACCOMMODATED,PIPE,OUTLET OUTLET PIPE SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE OUTLET PIPE THAT THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BKMKD 18TYPE,JOINT,OUTLET CONNECTION OUTLET CONNECTION JOINT TYPE INDICATES THE TYPE OF OUTLET CONNECTION JOINT PROVIDED. SELECT REPLY CODE 10AB76 BKMLD 18TYPE,STOPPER STOPPER TYPE INDICATES THE TYPE OF STOPPER PROVIDED. SELECT REPLY CODE 10AM35 BKMMD 18TYPE,STRAINER STRAINER TYPE INDICATES THE TYPE OF STRAINER PROVIDED. SELECT REPLY CODE 10AK54 BKMNJ 04DIAMETER,NOMINAL,TAILPIECE TAILPIECE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TAILPIECE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BKMPJ 04LENGTH,NOMINAL,TAILPIECE TAILPIECE NOMINAL LENGTH A MEASUREMENT OF THE LONGEST NOMINAL DIMENSION OF THE TAILPIECE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BKMQJ 10SIZE FOR WHICH DESIGNED,OUTLET OUTLET SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE OUTLET FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 BKMRD /D/ 07FEATURE,USAGE,VITREOUS CHINA SINK VITREOUS CHINA SINK USAGE FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM IS DESIGNED TO BE USED WITH A VITREOUS CHINA SINK. SELECT REPLY CODE 10AB22 BKMSD /D/ 19FORM FOR WHICH DESIGNED,PHYSICAL PHYSICAL FORM FOR WHICH DESIGNED THE RECOGNIZED SHAPE,CONFIGURATION,STRUCTURE,OR MOLD OF A SUBSTANCE,NATURAL OR REFINED,FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AE98 BKMTD 08LOCATION,SLOT,DISPENSING DISPENSING SLOT LOCATION INDICATES THE LOCATION OF THE DISPENSING SLOT. SELECT REPLY CODE 10AJ91 BKMWD /D/ 07STOP,ROLL,PAPER,AUTOMATIC AUTOMATIC PAPER ROLL STOP AN INDICATION OF WHETHER OR NOT AN AUTOMATIC PAPER ROLL STOP IS PROVIDED. IF PROVIDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AB22 BKMXJ T04SIZE FOR WHICH DESIGNED,OPENING OPENING SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE OPENING FOR WHICH THE ITEM IS DESIGNED. 1D AND 1F MODE REPLY11AA05 BKMYD 18TYPE,BRACKET,MOUNTING MOUNTING BRACKET TYPE INDICATES THE TYPE OF MOUNTING BRACKET PROVIDED. SELECT REPLY CODE 10AM39 BKMZG 19COMPONENT AND QUANTITY ACCOMMODATED COMPONENT AND QUANTITY ACCOMMODATED THE NAME OF THE ITEMS THE UNIT IS DESIGNED TO ACCOMMODATE,AND THE NUMBER OF EACH. FULL TEXT WRITE-IN 0 BKNBJ 04DIAMETER,NOMINAL NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BKNCJ 04WIDTH,OVERALL,BLOCK BLOCK OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BLOCK,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BKNDD 19CONDITION FOR WHICH DESIGNED,SURFACE,FABRIC FABRIC SURFACE CONDITION FOR WHICH DESIGNED THE CONDITION OF THE FABRIC WITH RESPECT TO THE TEXTURE OF THE SURFACE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK39 BKNFJ 04DIAMETER,END,HANDLE,BRUSH PART BRUSH PART HANDLE END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BRUSH PART HANDLE END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BKNGJ 04DIAMETER,TIP,BRUSH PART BRUSH PART TIP DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BRUSH PART TIP,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BKNHJ 04LENGTH,DIAMETER,CONSTANT,BRUSH PART BRUSH PART CONSTANT DIAMETER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A BRUSH PART CONSTANT DIAMETER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BKNJJ 04LENGTH,OVERALL,BRUSH PART BRUSH PART OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BRUSH PART. 2D AND 1B MODE REPLY21AA051AC20 BKNKJ 04HEIGHT INCLUDING BRISTLE,CHANNEL CHANNEL HEIGHT INCLUDING BRISTLE A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE CHANNEL INCLUDING THE BRISTLE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BKNLJ 04HEIGHT,SOLID,COIL COIL SOLID HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE SOLID COIL,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BKNMA 19NUMBER,MODEL,BRUSH BRUSH MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE BRUSH. 1A MODE REPLY 0 BKNNG 03DESIGNATION,SIZE,BRUSH BRUSH SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE BRUSH IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. FULL TEXT WRITE-IN 0 BKNPJ 04LENGTH,OVERALL,HANDLE HANDLE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE HANDLE. 2D AND 1B MODE REPLY21AA051AC20 BKNQG /D/ 03DESIGNATION,SIZE,END ITEM END ITEM SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE END ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. FULL TEXT WRITE-IN 0 BKNRA 19NUMBER,MODEL,END ITEM END ITEM MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE END ITEM. 1A MODE REPLY 0 BKNSJ 04LENGTH,BRUSH BRUSH LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BKNTJ /D/ 04WIDTH,BRUSH PART,SMALLEST SMALLEST BRUSH PART WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BKNWJ /D/ 04WIDTH,BRUSH PART,LARGEST LARGEST BRUSH PART WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BKNXJ 04LENGTH,BLOCK BLOCK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BKNYJ /D/ 10CURRENT RATING IN AMPS,INPUT INPUT CURRENT RATING IN AMPS THE AMOUNT OF INPUT CURRENT FOR WHICH THE ITEM IS RATED,EXPRESSED IN AMPERES. 1D AND 1B MODE REPLY13AN28 BKNZJ 10VOLTAGE RATING IN VOLTS,INPUT INPUT VOLTAGE RATING IN VOLTS THE INPUT VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN VOLTS. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 1D AND 1B MODE REPLY13AN28 BKPBD 11METHOD,RATING,CURRENT CURRENT RATING METHOD THE MEANS BY WHICH THE CURRENT IS RATED. SELECT REPLY CODE 10AN29 BKPCJ 10TYPE IN VOLTS,OUTPUT,CALIBRATION VOLTAGE CALIBRATION VOLTAGE OUTPUT TYPE IN VOLTS AN INDICATION OF THE TYPE OF CALIBRATION VOLTAGE OUTPUT,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AB62 BKPDJ /D/ 18TYPE AND RATING IN VOLTS,VOLTAGE,AC OUTPUT CONNECTION AC OUTPUT CONNECTION VOLTAGE TYPE AND RATING IN VOLTS INDICATES THE TYPE OF ALTERNATING CURRENT OUTPUT CONNECTION VOLTAGE AND ITS RATING,EXPRESSED IN VOLTS. 2D AND 1B MODE REPLY23AN993AN28 BKPFJ /D/ 10VOLTAGE RATING IN VOLTS,OUTPUT,DC DC OUTPUT VOLTAGE RATING IN VOLTS THE RATED DIRECT CURRENT OUTPUT VOLTAGE THE ITEM IS DESIGNED TO PRODUCE,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY13AN28 BKPGJ /D/ 18TYPE AND RATING IN AMPS,CURRENT,OUTPUT FULL LOAD OUTPUT FULL LOAD CURRENT TYPE AND RATING IN AMPS INDICATES THE TYPE OF OUTPUT FULL LOAD CURRENT AND ITS RATING,EXPRESSED IN AMPERES. 2D AND 1B MODE REPLY21AB623AN28 BKPHJ 10TORQUE RATING AND TYPE TORQUE RATING AND TYPE INDICATES THE TORQUE RATING,AND ITS TYPE. 2D AND 1B MODE REPLY21AA562AJ34 BKPJJ /D/ 10SPEED RATING IN RPM,ROTOR,NO LOAD NO LOAD ROTOR SPEED RATING IN RPM THE SPEED RATING OF A ROTOR UNDER A NO LOAD CONDITION,EXPRESSED IN REVOLUTIONS PER MINUTE. 1D AND 1B MODE REPLY13AN28 BKPKJ /D/ 10SPEED RATING IN RPM,ROTOR,FULL LOAD FULL LOAD ROTOR SPEED RATING IN RPM THE SPEED RATING OF A ROTOR UNDER A FULL LOAD CONDITION,EXPRESSED IN REVOLUTIONS PER MINUTE. 1D AND 1B MODE REPLY13AN28 BKPLD 11METHOD,RATING RATING METHOD THE MEANS BY WHICH THE RATING IS DETERMINED. SELECT REPLY CODE 10AN29 BKPMJ /D/ 10SPEED RATING IN RPM,SHAFT,OUTPUT,GEARED HEAD FIRST DRIVE GEARED HEAD FIRST DRIVE OUTPUT SHAFT SPEED RATING IN RPM THE RATED SPEED OF THE GEARED HEAD FIRST DRIVE OUTPUT SHAFT,EXPRESSED IN REVOLUTIONS PER MINUTE. 1D AND 1B MODE REPLY13AN28 BKPNJ /D/ 10SPEED RATING IN RPM,SHAFT,OUTPUT,GEARED HEAD SECOND DRIVE GEARED HEAD SECOND DRIVE OUTPUT SHAFT SPEED RATING IN RPM THE RATED SPEED OF THE GEARED HEAD SECOND DRIVE OUTPUT SHAFT,EXPRESSED IN REVOLUTIONS PER MINUTE. 1D AND 1B MODE REPLY13AN28 BKPPH 11METHOD AND DEVICE TYPE,CONTROL,SPEED SPEED CONTROL METHOD AND DEVICE TYPE THE MEANS BY WHICH THE SPEED IS CONTROLLED AND THE TYPE OF DEVICE USED. 2D MODE REPLY 23AL283AM97 BKPQD 19SPECIFICATION,INCLOSURE INCLOSURE SPECIFICATION THE GOVERNMENT OR INDUSTRIAL SPECIFICATION OR STANDARD THAT DEFINES THE INCLOSURE FEATURE. SELECT REPLY CODE 10AN30 BKPRD /D/ 11METHOD,SWITCHING,SHAFT ROTATION SHAFT ROTATION SWITCHING METHOD THE MEANS USED FOR SWITCHING THE SHAFT ROTATION. SELECT REPLY CODE 10AC58 BKPSJ 18TYPE AND RATING IN VOLTS,VOLTAGE,CONTROL FIELD CONTROL FIELD VOLTAGE TYPE AND RATING IN VOLTS INDICATES THE TYPE OF CONTROL FIELD VOLTAGE AND ITS RATING,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AB62 BKPTD /D/ 07REEL REEL AN INDICATION OF WHETHER A REEL(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BKPWA 12QUANTITY,REEL,ACCOMMODATED ACCOMMODATED REEL QUANTITY THE NUMBER OF REELS THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 BKPXG 13THREAD DESIGNATION THREAD DESIGNATION NONE. FULL TEXT WRITE-IN 0 BKPYJ /D/ 04DIAMETER,BRUSH PART,TAPERED SMALL END TAPERED SMALL END BRUSH PART DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BKPZJ 04LENGTH,BRUSH,TIP TIP BRUSH LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BKQBD 02DESIGN ACCOMMODATED,PANEL PANEL DESIGN ACCOMMODATED THE DESIGN OF THE PANEL ACCOMMODATED. SELECT REPLY CODE 10AL59 BKQCD /D/ 08LOCATION,COLOR,BACKGROUND BACKGROUND COLOR LOCATION INDICATES THE LOCATION OF AN ITEM TO WHICH THE BACKGROUND COLOR IS APPLIED. SELECT REPLY CODE 10AJ91 BKQDD 18TYPE,TOP,COMPARTMENT COMPARTMENT TOP TYPE INDICATES THE TYPE OF COMPARTMENT TOP PROVIDED. SELECT REPLY CODE 10AK54 BKQFJ A18TYPE AND QUANTITY,PANEL PANEL TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF PANEL(S) PROVIDED. 1D AND 1A MODE REPLY12AH22 BKQGJ 04HEIGHT,PANEL PANEL HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE PANEL,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BKQHD /D/ 07EDGE,FLANGED FLANGED EDGE AN INDICATION OF WHETHER OR NOT A FLANGED EDGE IS PROVIDED. SELECT REPLY CODE 10AB22 BKQJD /D/ 07FEATURE,TOP,COVERED COVERED TOP FEATURE AN INDICATION OF WHETHER OR NOT A COVERED TOP FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BKQKD 18TYPE,COVER,TOP TOP COVER TYPE INDICATES THE TYPE OF TOP COVER FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AK54 BKQLD /D/ 07SHELF,WORK,SLIDING SLIDING WORK SHELF AN INDICATION OF WHETHER OR NOT A SLIDING WORK SHELF IS INCLUDED. SELECT REPLY CODE 10AA49 BKQMD /D/ 07SHELF,BOTTOM BOTTOM SHELF AN INDICATION OF WHETHER OR NOT A BOTTOM SHELF IS INCLUDED. SELECT REPLY CODE 10AA49 BKQNA 10CAPACITY,CARD CARD CAPACITY THE NUMBER OF CARD(S) THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 BKQPD /D/ 07HANGER HANGER AN INDICATION OF WHETHER OR NOT A HANGER/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BKQQG /D/ 19SYMBOL SYMBOL THE LETTERING OR DESIGN ON THE ITEM. FULL TEXT WRITE-IN 0 BKQRD /D/ 08LOCATION,SYMBOL SYMBOL LOCATION INDICATES THE LOCATION OF THE SYMBOL ON THE ITEM. SELECT REPLY CODE 10AJ91 BKQSA 12QUANTITY,HANGER HANGER QUANTITY THE NUMBER OF HANGER(S) PROVIDED. 1A MODE REPLY 0 BKQTJ /D/ 04LENGTH,SYMBOL SYMBOL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SYMBOL,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BKQWD /D/ 07MAGNET,PERMANENT PERMANENT MAGNET AN INDICATION OF WHETHER OR NOT A PERMANENT MAGNET IS PROVIDED IN THE ITEM. SELECT REPLY CODE 10AB22 BKQXD /D/ 07FEATURE,WAXED WAXED FEATURE AN INDICATION OF WHETHER OR NOT A WAXED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BKQYG 02DESIGN DESIGN A NARRATIVE EXPRESSION USED TO DESCRIBE THE DESIGN OF THE ITEM. FULL TEXT WRITE-IN 0 BKQZJ /D/A10CAPACITY IN POINT THICKNESS,POCKET/CARD POCKET/CARD CAPACITY IN POINT THICKNESS THE POCKET OR CARD CAPACITY OF THE ITEM,EXPRESSED IN POINT THICKNESS. 1D AND 1A MODE REPLY11AC20 BKRBD /D/ 07PROVISION,SHEET,DUAL SUPLICATING DUAL DUPLICATING SHEET PROVISION AN INDICATION OF WHETHER OR NOT A PROVISION FOR A DUAL DUPLICATING SHEET IS INCLUDED. SELECT REPLY CODE 10AA49 BKRCJ /D/ 04DIMENSION,PORTION,EXPOSED,POCKET/CARD POCKET/CARD EXPOSED PORTION DIMENSION A MEASUREMENT OF THE EXPOSED PORTION OF THE POCKET OR CARD ACCOMMODATED. 2D AND 1B MODE REPLY21AA051AC20 BKRDD /D/ 07BRACKET,HOLDING HOLDING BRACKET AN INDICATION OF WHETHER OR NOT A HOLDING BRACKET/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BKRFD 19CONDITION,SURFACE,WORKING SIDE WORKING SIDE SURFACE CONDITION THE CONDITION OF THE WORKING SIDE OF THE ITEM WITH RESPECT TO THE TEXTURE OF THE SURFACE. SELECT REPLY CODE 10AK39 BKRGD 19CONDITION,SURFACE,OPPOSITE WORKING SIDE OPPOSITE WORKING SIDE SURFACE CONDITION THE CONDITION OF THE SURFACE OPPOSITE THE WORKING SIDE WITH RESPECT TO THE TEXTURE. SELECT REPLY CODE 10AK39 BKRHD 01COLOR,RULING,PRINTED PRINTED RULING COLOR THE HUE OR TINT OF THE PRINTED RULING. SELECT REPLY CODE 10AD06 BKRJD 18TYPE,RULING,PRINTED PRINTED RULING TYPE INDICATES THE TYPE OF PRINTED RULING PROVIDED. SELECT REPLY CODE 10AK54 BKRKD /D/ 07FEATURE,RESISTANT,RUST RUST RESISTANT FEATURE AN INDICATION OF WHETHER OR NOT A RUST RESISTANT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BKRLG /D/ 19CHARACTERISTICS,RULING RULING CHARACTERISTICS A NARRATIVE EXPRESSION USED TO DESCRIBE THE CHARACTERISTICS OF THE RULING/S/ ON THE ITEM. FULL TEXT WRITE-IN 0 BKRMD 18TYPE,BACK BACK TYPE INDICATES THE TYPE OF BACK ON THE ITEM. SELECT REPLY CODE 10AL60 BKRNJ 04WIDTH,EXPOSED EXPOSED WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE EXPOSED PORTION,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BKRPJ /D/ 04LENGTH ACCOMMODATED,CARD/SHEET CARD/SHEET LENGTH ACCOMMODATED A MEASUREMENT OF THE LONGEST DIMENSION OF A CARD OR SHEET THE ITEM WILL ACCOMMODATE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BKRQJ /D/ 04WIDTH ACCOMMODATED,CARD/SHEET CARD/SHEET WIDTH ACCOMMODATED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A CARD OR SHEET ACCOMMODATED BY THE ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BKRRD /D/ 07SLOT,CARD,MULTIPLE SIZE MULTIPLE SIZE CARD SLOT AN INDICATION OF WHETHER OR NOT A MULTIPLE SIZE CARD SLOT(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BKRSJ 04LENGTH,HOLDER HOLDER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE HOLDER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BKRTJ /D/T04SIZE ACCOMMODATED,CARD,SLOT SLOT CARD SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE CARD(S) ACCOMMODATED BY THE SLOT(S). 1D AND 1F MODE REPLY11AA05 BKRWD /D/ 07EDGE,CELLULOID CELLULOID EDGE AN INDICATION OF WHETHER OR NOT A CELLULOID EDGE IS PROVIDED. SELECT REPLY CODE 10AB22 BKRXD 18TYPE,BACKGROUND,CHARACTER CHARACTER BACKGROUND TYPE INDICATES THE TYPE OF BACKGROUND PROVIDED FOR THE CHARACTER(S). SELECT REPLY CODE 10AK54 BKRYJ A18TYPE AND QUANTITY FOR WHICH DESIGNED,ROW ROW TYPE AND QUANTITY FOR WHICH DESIGNED INDICATES THE TYPE AND NUMBER OF ROW/S/ USED ON THE ITEM. 1D AND 1A MODE REPLY13AK54 BKRZD 19PURPOSE FOR WHICH DESIGNED,HOLDING HOLDING PURPOSE FOR WHICH DESIGNED THE HOLDING PURPOSE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL53 BKSBD 11METHOD,ATTACHMENT,MICROPHONE MICROPHONE ATTACHMENT METHOD THE MEANS USED TO ATTACH THE MICROPHONE. SELECT REPLY CODE 10AM39 BKSCD /D/ 07COIL,VOICE VOICE COIL AN INDICATION OF WHETHER OR NOT A VOICE COIL IS INCLUDED. USE MRC CBBL WITH CODED REPLY OF GKJ - VOICE COIL. SELECT REPLY CODE 10AA49 BKSDJ 10IMPEDANCE RATING,COIL,VOICE VOICE COIL IMPEDANCE RATING THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) WHICH THE VOICE COIL OFFERS TO THE FLOW OF ALTERNATING CURRENT. 2D AND 1B MODE REPLY22AE751AC20 BKSFJ 10IMPEDANCE RATING,COIL,ARMATURE ARMATURE COIL IMPEDANCE RATING THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) WHICH THE ARMATURE COIL OFFERS TO THE FLOW OF ALTERNATING CURRENT. 2D AND 1B MODE REPLY22AE751AC20 BKSGJ T04SIZE FOR WHICH DESIGNED,SPEAKER SPEAKER SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE SPEAKER FOR WHICH THE ITEM IS DESIGNED. 1D AND 1F MODE REPLY11AA05 BKSHB 10WATTAGE RATING IN WATTS,INPUT,NORMAL NORMAL INPUT WATTAGE RATING IN WATTS THE RATED NORMAL INPUT POWER THAT AN ITEM CAN SAFELY CONSUME,MEASURED IN WATTS. 1B MODE REPLY 0 BKSJB 10WATTAGE RATING IN WATTS,INPUT,PEAK PEAK INPUT WATTAGE RATING IN WATTS THE RATED PEAK INPUT POWER THAT AN ITEM CAN SAFELY CONSUME,MEASURED IN WATTS. 1B MODE REPLY 0 BKSKJ 04SIZE,DIAPHRAGM,NOMINAL NOMINAL DIAPHRAGM SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE NOMINAL DIMENSIONS OF THE DIAPHRAGM. 1D AND 1B MODE REPLY11AA05 BKSLJ 10IMPEDANCE RATING,PRIMARY,TRANSFORMER TRANSFORMER PRIMARY IMPEDANCE RATING THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) WHICH THE TRANSFORMER PRIMARY OFFERS TO THE FLOW OF ALTERNATING CURRENT IN THE TRANSFORMER. 1D AND 1B MODE REPLY12AE75 BKSMJ 04LENGTH DEVELOPED,ACOUSTIC ACOUSTIC LENGTH DEVELOPED A MEASUREMENT OF THE ACOUSTIC LENGTH DEVELOPED BY THE ITEM. 1D AND 1B MODE REPLY11AA05 BKSND 18TYPE ACCOMMODATED,DEVICE DEVICE TYPE ACCOMMODATED INDICATES THE TYPE OF DEVICE THE ITEM WILL ACCOMMODATE. SELECT REPLY CODE 10AG97 BKSPG /D/ 11METHOD,COUPLING COUPLING METHOD THE MEANS USED TO COUPLE THE ITEM TO ANOTHER ITEM. FULL TEXT WRITE-IN 0 BKSQJ 10IMPEDANCE RATING,EARPHONE EARPHONE IMPEDANCE RATING THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) WHICH THE EARPHONE OFFERS TO THE FLOW OF ALTERNATING CURRENT. 2D AND 1B MODE REPLY22AE751AC20 BKSRJ 10RESISTANCE RATING,DC,EARPHONE EARPHONE DC RESISTANCE RATING THE OPPOSITION TO THE FLOW OF DIRECT CURRENT OFFERED BY AN EARPHONE. 2D AND 1B MODE REPLY22AE751AC20 BKSSG 19AGENCY,CONTROLLING,EARPHONE EARPHONE CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE EARPHONE. FULL TEXT WRITE-IN 0 BKSTJ A19NUMBER,IDENTIFYING,EARPHONE EARPHONE IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERICAL ORGANIZATION CONTROLLING THE EARPHONE. 1D AND 1A MODE REPLY12AG99 BKSWD 18TYPE,ELEMENT,MICROPHONE MICROPHONE ELEMENT TYPE INDICATES THE TYPE OF MICROPHONE ELEMENT OR CARTRIDGE AS DETERMINED BY ITS CONSTRUCTION AND METHOD OF OPERATION. SELECT REPLY CODE 10AC58 BKSXG 10LEVEL RATING,OUTPUT OUTPUT LEVEL RATING AN INDICATION OF THE RATED ELECTRICAL OUTPUT OF THE ITEM. FULL TEXT WRITE-IN 0 BKSYD 11METHOD,MOUNTING,EARPHONE EARPHONE MOUNTING METHOD THE MEANS OF ATTACHING THE EARPHONE. SELECT REPLY CODE 10AM39 BKSZD 19FACILITY,MOUNTING,MICROPHONE MICROPHONE MOUNTING FACILITY THE MEANS PROVIDED TO MOUNT OR OTHERWISE ACCOMMODATE A MICROPHONE. SELECT REPLY CODE 10AM39 BKTBD 19NAME,CONNECTOR CONNECTOR NAME THE NOMENCLATURE BY WHICH THE CONNECTOR IS IDENTIFIED. SELECT REPLY CODE 10AK95 BKTCD /D/ 07BASE,MOUNTING,INSULATED INSULATED MOUNTING BASE AN INDICATION OF WHETHER OR NOT AN INSULATED MOUNTING BASE IS INCLUDED. SELECT REPLY CODE 10AA49 BKTDD /D/ 07COATING,JACKET JACKET COATING AN INDICATION OF WHETHER OR NOT A JACKET COATING IS INCLUDED. SELECT REPLY CODE 10AA49 BKTFJ A19NUMBER,IDENTIFYING,CONNECTOR CONNECTOR IDENTIFYING NUMBER A NUMBER ASSIGNED TO THE CONNECTOR FOR PURPOSE OF READY IDENTIFICATION. 1D AND 1A MODE REPLY12AG99 BKTGJ 04LENGTH,CORD,CONNECTOR TO JUNCTION CONNECTOR TO JUNCTION CORD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CORD FROM A CONNECTOR TO A JUNCTION,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BKTHD /D/ 09MATERIAL,PLATE,CHEST CHEST PLATE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CHEST PLATE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BKTJD 11METHOD,SUSPENSION,CHEST PLATE CHEST PLATE SUSPENSION METHOD THE MEANS USED TO SUSPEND THE CHEST PLATE. SELECT REPLY CODE 10AM39 BKTKD /D/ 07CORD CORD AN INDICATION OF WHETHER OR NOT A CORD IS PROVIDED. SELECT REPLY CODE 10AB22 BKTLD /D/ 07PLUG,TYPE,TELEPHONE TELEPHONE TYPE PLUG AN INDICATION OF WHETHER OR NOT A TELEPHONE TYPE PLUG IS PROVIDED. SELECT REPLY CODE 10AB22 BKTMJ 04DIAMETER,SHANK SHANK DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR SHANK,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BKTND /D/ 18TYPE,TERMINATION,CONNECTOR CONNECTOR TERMINATION TYPE INDICATES THE TYPE OF CONNECTOR TERMINATION PROVIDED. SELECT REPLY CODE 10AA58 BKTPG /D/ 04SIZE,NUT/SHELL,CONNECTOR COUPLING CONNECTOR COUPLING NUT/SHELL SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF A COUPLING NUT OR SHELL. FULL TEXT WRITE-IN 0 BKTQD 18TYPE,TERMINATION,INDIVIDUAL CONNECTOR INDIVIDUAL CONNECTOR TERMINATION TYPE INDICATES THE TYPE OF INDIVIDUAL CONDUCTOR TERMINATION(S) PROVIDED. SELECT REPLY CODE 10AE79 BKTRJ 10VOLTAGE RATING,DC,FIELD EXCITATION FIELD EXCITATION DC VOLTAGE RATING THE DIRECT CURRENT VOLTAGE REQUIRED TO EXCITE THE FIELD. 1D AND 1B MODE REPLY11AB63 BKTSJ 10DC RATING DC RATING THE DIRECT CURRENT RATING FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AC30 BKTTA 12QUANTITY,LOUDSPEAKER,INDIVIDUAL INDIVIDUAL LOUDSPEAKER QUANTITY THE NUMBER OF INDIVIDUAL LOUDSPEAKER(S) PROVIDED. 1A MODE REPLY 0 BKTWJ T10RANGE,FREQUENCY,INDIVIDUAL LOUDSPEAKER INDIVIDUAL LOUDSPEAKER FREQUENCY RANGE THE RANGE OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH AN INDIVIDUAL LOUDSPEAKER IS RATED. 1D AND 1F MODE REPLY11AC32 BKTXG /D/ 04SIZE,CONE/HORN,INDIVIDUAL LOUDSPEAKER INDIVIDUAL LOUDSPEAKER CONE/HORN SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE CONE OR HORN. FULL TEXT WRITE-IN 0 BKTYJ 10POWER RATING,AUDIO,INDIVIDUAL LOUDSPEAKER INDIVIDUAL LOUDSPEAKER AUDIO POWER RATING THE AMOUNT OF ELECTRICAL ENERGY THAT CAN BE DISSIPATED FOR THE INDIVIDUAL LOUDSPEAKER. 1D AND 1B MODE REPLY11AC33 BKTZJ /D/ 10IMPEDANCE,INPUT,NOMINAL,INDIVIDUAL LOUDSPEAKER INDIVIDUAL LOUDSPEAKER NOMINAL INPUT IMPEDANCE THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) WHICH THE INDIVIDUAL LOUDSPEAKER OFFERS TO THE NOMINAL INPUT FLOW OF ALTERNATING CURRENT. 1D AND 1B MODE REPLY11AA57 BKWBJ 04WIDTH,BRUSH,TIP TIP BRUSH WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BKWCJ 04DIAMETER,OUTSIDE,ACCOMMODATED REEL ACCOMMODATED REEL OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ACCOMMODATED REEL,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BKWDJ 04WIDTH,ACCOMMODATED REEL ACCOMMODATED REEL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ACCOMMODATED REEL FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BKWFD 07REMOVABILITY,REEL REEL REMOVABILITY AN INDICATION OF WHETHER OR NOT THE REEL IS REMOVABLE. SELECT REPLY CODE 10AC29 BKWGA 12QUANTITY,SHAFT,REEL REEL SHAFT QUANTITY THE NUMBER OF REEL SHAFT(S) PROVIDED. 1A MODE REPLY 0 BKWHD 14SHAPE,SHAFT,REEL REEL SHAFT SHAPE THE PHYSICAL CONFIGURATION OF THE REEL SHAFT. SELECT REPLY CODE 10AD07 BKWKD /D/ 07CONNECTION,ELECTRICAL,COMMUNICATION SYSTEM COMMUNICATION SYSTEM ELECTRICAL CONNECTION AN INDICATION OF WHETHER OR NOT A COMMUNICATION SYSTEM ELECTRICAL CONNECTION IS INCLUDED. SELECT REPLY CODE 10AA49 BKWLD /D/ 07FEATURE,COMMUNICATION MAINTAINED DURING REELING MACHINE OPERATION COMMUNICATION MAINTAINED DURING REELING MACHINE OPERATION FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE FOR MAINTAINING COMMUNICATIONS DURING REELING MACHINE OPERATION IS INCLUDED. SELECT REPLY CODE 10AA49 BKWMD 19SOURCE,POWER,REEL REEL POWER SOURCE THE SOURCE OF POWER UTILIZED TO OPERATE THE REEL/S/. SELECT REPLY CODE 10AG27 BKWND /D/ 07PROVISION,OPERATING,MANUAL MANUAL OPERATING PROVISION AN INDICATION OF WHETHER OR NOT A MANUAL OPERATING PROVISION IS INCLUDED. SELECT REPLY CODE 10AA49 BKWPD 18TYPE,DESIGN,ENGINE ENGINE DESIGN TYPE INDICATES THE TYPE OF ENGINE DESIGN. SELECT REPLY CODE 10AK54 BKWQA 12QUANTITY,CYLINDER,ENGINE ENGINE CYLINDER QUANTITY THE NUMBER OF CYLINDERS PROVIDED IN THE ENGINE. 1A MODE REPLY 0 BKWRD 11METHOD,COOLING,ENGINE ENGINE COOLING METHOD THE MEANS BY WHICH THE ENGINE IS COOLED. SELECT REPLY CODE 10AN05 BKWSD /D/ 07CRANK CRANK AN INDICATION OF WHETHER OR NOT A CRANK IS PROVIDED. SELECT REPLY CODE 10AB22 BKWTJ /D/ 04LENGTH,TRAILER TRAILER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A TRAILER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BKWWJ 04WIDTH,TRAILER TRAILER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A TRAILER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BKWXD 18TYPE,TIRE,ADJUSTING WHEEL ADJUSTING WHEEL TIRE TYPE INDICATES THE TYPE OF TIRE PROVIDED ON THE ADJUSTING WHEEL. SELECT REPLY CODE 10AH67 BKWYJ 10WEIGHT,MINIMUM MINIMUM WEIGHT THE MINIMUM WEIGHT OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BKWZJ 10WEIGHT,WORKING,MAXIMUM MAXIMUM WORKING WEIGHT THE MAXIMUM WORKING WEIGHT OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BKXBJ 04WIDTH,ROLLING ROLLING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE AREA ROLLED BY THE ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BKXCJ 10SPEED,RATED,MAXIMUM MAXIMUM RATED SPEED THE MAXIMUM RATED SPEED FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY12AG67 BKXDJ 10SPEED,RATED,MINIMUM MINIMUM RATED SPEED THE MINIMUM RATED SPEED FOR WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY12AG67 BKXFD /D/ 07CONVERTER,TORQUE TORQUE CONVERTER AN INDICATION OF WHETHER OR NOT A TORQUE CONVERTER IS INCLUDED. SELECT REPLY CODE 10AA49 BKXGJ 04DIAMETER,ROLL,DRIVE DRIVE ROLL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DRIVE ROLL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BKXHJ 04WIDTH,ROLL,DRIVE DRIVE ROLL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A DRIVE ROLL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BKXJJ 04DIAMETER,ROLL,STEERING STEERING ROLL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE STEERING ROLL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BKXKJ 04WIDTH,ROLL,STEERING STEERING ROLL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE STEERING ROLL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BKXLJ 10CAPACITY,BALLAST,HOPPER HOPPER BALLAST CAPACITY THE AMOUNT OF BALLAST THE HOPPER WILL HOLD. 1D AND 1B MODE REPLY12AG67 BKXMA 12QUANTITY,DRUM DRUM QUANTITY THE NUMBER OF DRUMS PROVIDED. 1A MODE REPLY 0 BKXNJ 04WIDTH,OVERALL,DRUM DRUM OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A DRUM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BKXPJ 04DIAMETER,OVERALL,DRUM DRUM OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE CIRCULAR CROSS-SECTIONAL PLANE OF THE DRUM. 2D AND 1B MODE REPLY21AA051AC20 BKXQJ 04LENGTH,OVERALL,TAMPING FOOT TAMPING FOOT OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE TAMPING FOOT. 2D AND 1B MODE REPLY21AA051AC20 BKXRJ 10AREA,FACE,TAMPING FOOT TAMPING FOOT FACE AREA A MEASUREMENT OF THE FACE AREA OF A TAMPING FOOT. 2D AND 1B MODE REPLY22AG671AC20 BKXSA 12QUANTITY PER DRUM,FOOT,TAMPING TAMPING FOOT QUANTITY PER DRUM THE NUMBER OF TAMPING FEET INCLUDED IN EACH DRUM. 1A MODE REPLY 0 BKXTJ 10WEIGHT,EMPTY EMPTY WEIGHT THE WEIGHT OF THE ITEM WHEN EMPTY. 2D AND 1B MODE REPLY22AG671AC20 BKXWJ 10WEIGHT,FILLED FILLED WEIGHT THE WEIGHT OF THE ITEM WHEN FILLED. 2D AND 1B MODE REPLY22AG671AC20 BKXXJ 04WIDTH,OVERALL,COMPACTING COMPACTING OVERALL WIDTH AN OVERALL DIMENSION TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE AREA AN ITEM CAN EFFECTIVELY COMPACT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BKXZJ /D/ 10CLEARANCE,TRUCK,LATERAL,MINIMUM MINIMUM LATERAL TRUCK CLEARANCE THE MINIMUM LATERAL TRUCK CLEARANCE OF THE ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1D AND 1B MODE REPLY11AA05 BKYBJ 04DISTANCE FROM ELBOW CENTER BEND TO END DISTANCE FROM ELBOW CENTER BEND TO END THE DISTANCE FROM THE CENTER OF THE ELBOW BEND TO THE END. 1D AND 1B MODE REPLY11AA05 BKYCJ 04LENGTH,OFFSET OFFSET LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE OFFSET,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BKYDD /D/ 07NUT,SLIP SLIP NUT AN INDICATION OF WHETHER OR NOT A SLIP NUT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BKYFD /D/ 07WASHER,NUT,SLIP SLIP NUT WASHER AN INDICATION OF WHETHER OR NOT A SLIP NUT WASHER/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BKYGD /D/ 19FINISH,ENAMEL ENAMEL FINISH AN INDICATION OF THE ENAMEL FINISH PROVIDED. SELECT REPLY CODE 10AA65 BKYHD /D/ 08LOCATION,OPENING,RECEPTOR INLET RECEPTOR INLET OPENING LOCATION INDICATES THE LOCATION OF THE RECEPTOR INLET OPENING. SELECT REPLY CODE 10AJ91 BKYJD /D/ 08LOCATION,OUTLET,WASTE RECEPTOR WASTE RECEPTOR OUTLET LOCATION INDICATES THE LOCATION OF THE WASTE RECEPTOR OUTLET. SELECT REPLY CODE 10AJ91 BKYKD /D/ 07TRAP,INTEGRAL,RECEPTOR RECEPTOR INTEGRAL TRAP AN INDICATION OF WHETHER OR NOT A TRAP IS INCLUDED AS AN INTEGRAL PART OF THE RECEPTOR. MRC DISCONTINUED AND REPLACED WITH MRC CBBL AND REPLY CODE GSU, INTEGRAL TRAP ON 03/28/2024. SELECT REPLY CODE 10AA49 BKYLD /D/ 07SHIELD,SIDE,INTEGRAL,RECEPTOR RECEPTOR INTEGRAL SIDE SHIELD AN INDICATION OF WHETHER OR NOT A SIDE SHIELD IS INCLUDED AS AN INTEGRAL PART OF THE RECEPTOR. SELECT REPLY CODE 10AA49 BKYMD 08LOCATION,SHIELD,SIDE,INTEGRAL,RECEPTOR RECEPTOR INTEGRAL SIDE SHIELD LOCATION INDICATES THE LOCATION OF THE INTEGRAL SIDE SHIELD ON THE RECEPTOR. SELECT REPLY CODE 10AJ91 BKYNJ 04LENGTH,TROUGH TROUGH LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TROUGH,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BKYPD /D/ 07BUCKET,INNER INNER BUCKET AN INDICATION OF WHETHER OR NOT AN INNER BUCKET IS INCLUDED. SELECT REPLY CODE 10AA49 BKYQJ 04DIAMETER,OVERALL,BUCKET BUCKET OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF THE BUCKET. 2D AND 1B MODE REPLY21AA051AC20 BKYRJ 04DIAMETER,OVERALL,VENT VENT OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF THE VENT. 2D AND 1B MODE REPLY21AA051AC20 BKYSA 12QUANTITY,SHOWERHEAD SHOWERHEAD QUANTITY THE NUMBER OF SHOWERHEAD(S) PROVIDED. 1A MODE REPLY 0 BKYTD /D/ 07EXCHANGER,HEAT HEAT EXCHANGER AN INDICATION OF WHETHER OR NOT A HEAT EXCHANGER IS PROVIDED. SELECT REPLY CODE 10AB22 BKYWD /D/ 09MATERIAL,BOILER BOILER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BOILER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BKYXD 11METHOD,CONNECTION,INLET INLET CONNECTION METHOD THE MEANS USED TO CONNECT THE INLET. SELECT REPLY CODE 10AJ68 BKYYD 13THREAD LOCATION,CONNECTION,INLET INLET CONNECTION THREAD LOCATION THE PORTION OF THE INLET CONNECTION ON WHICH THE THREAD(S) IS LOCATED. SELECT REPLY CODE 10AJ91 BKYZD /D/ 07FEATURE,ANTISIPHON ANTISIPHON FEATURE AN INDICATION OF WHETHER OR NOT AN ANTISIPHON FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BKZBD /D/ 07STANDARD,ADJUSTABLE ADJUSTABLE STANDARD AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE STANDARD IS PROVIDED. SELECT REPLY CODE 10AB22 BKZCJ 04SIZE ACCOMMODATED,PIPE,NOMINAL,OUTLET CONNECTION OUTLET CONNECTION NOMINAL PIPE SIZE ACCOMMODATED THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE OUTLET CONNECTION IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BKZDD 11METHOD,CONNECTION,OUTLET OUTLET CONNECTION METHOD THE MEANS USED TO CONNECT THE OUTLET. SELECT REPLY CODE 10AJ68 BKZFJ 04SIZE ACCOMMODATED,PIPE,NOMINAL,INLET CONNECTION INLET CONNECTION NOMINAL PIPE SIZE ACCOMMODATED THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE INLET CONNECTION IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BKZGD /D/ 07PLUG,CLEANOUT CLEANOUT PLUG AN INDICATION OF WHETHER OR NOT A CLEANOUT PLUG IS PROVIDED. SELECT REPLY CODE 10AB22 BKZHJ 13THREAD DIAMETER,TUBE TUBE THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE TUBE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BKZJD /D/ 07FEATURE,END,FLARED FLARED END FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES A FLARED END. SELECT REPLY CODE 10AA49 BKZKD /D/ 07FEATURE,END,ROLLED EXTENSION LIP ROLLED EXTENSION LIP END FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES A ROLLED EXTENSION LIP ON ONE END. SELECT REPLY CODE 10AA49 BKZLJ 04DIAMETER ACCOMMODATED,OUTSIDE,DRAIN OUTLET DRAIN OUTLET OUTSIDE DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED DRAIN OUTLET,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BKZMD /D/ 07FEATURE,BODY,CREVICE-FREE/SEAMLESS CREVICE-FREE/SEAMLESS BODY FEATURE AN INDICATION OF WHETHER OR NOT A CREVICE-FREE OR SEAMLESS BODY CONSTRUCTION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BKZND /D/ 07GASKET,SPOUT SPOUT GASKET AN INDICATION OF WHETHER OR NOT A SPOUT GASKET(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BKZPJ 04DIAMETER,BOTTOM,OVERALL OVERALL BOTTOM DIAMETER THE OVERALL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR BOTTOM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BKZQA 12QUANTITY,BASKET BASKET QUANTITY THE NUMBER OF BASKET(S) PROVIDED. 1A MODE REPLY 0 BKZRD 07REMOVABILITY,BASKET BASKET REMOVABILITY AN INDICATION OF WHETHER OR NOT THE BASKET(S) IS REMOVABLE. SELECT REPLY CODE 10AC29 BKZSJ 04WIDTH AT BACK,OVERALL,BASE BASE OVERALL WIDTH AT BACK AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BASE AT THE BACK,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BKZTJ 04WIDTH AT FRONT,OVERALL,BASE BASE OVERALL WIDTH AT FRONT AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BASE AT THE FRONT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BKZWA 12QUANTITY,WHEEL,NONSWIVEL NONSWIVEL WHEEL QUANTITY THE NUMBER OF NONSWIVEL WHEEL(S) PROVIDED. 1A MODE REPLY 0 BKZXA 12QUANTITY,WHEEL,SWIVEL SWIVEL WHEEL QUANTITY THE NUMBER OF SWIVEL WHEEL(S) PROVIDED. 1A MODE REPLY 0 BKZYD /D/ 07BASKET,AUXILIARY,BUILT-IN BUILT-IN AUXILIARY BASKET AN INDICATION OF WHETHER OR NOT A BUILT-IN AUXILIARY BASKET IS INCLUDED. SELECT REPLY CODE 10AA49 BKZZD /D/ 07SEAT,BABY BABY SEAT AN INDICATION OF WHETHER OR NOT A BABY SEAT IS PROVIDED. SELECT REPLY CODE 10AB22 BLACJ 04LENGTH ACCOMMODATED,BLADE BLADE LENGTH ACCOMMODATED A MEASUREMENT OF THE LONGEST DIMENSION OF THE BLADE ACCOMMODATED,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BLBBD /D/ 07BASKET,HINGED HINGED BASKET AN INDICATION OF WHETHER OR NOT A HINGED BASKET(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BLBCD /D/ 07CHARACTERS,TRANSPARENT TRANSPARENT CHARACTERS AN INDICATION OF WHETHER OR NOT TRANSPARENT CHARACTERS ARE INCLUDED. SELECT REPLY CODE 10AA49 BLBDD /D/ 07CHARACTERS,ARTWORK ARTWORK CHARACTERS AN INDICATION OF WHETHER OR NOT ARTWORK CHARACTERS ARE INCLUDED. SELECT REPLY CODE 10AA49 BLBFG /D/ 19SYMBOL,PREFIX/SUFFIX PREFIX/SUFFIX SYMBOL THE SYMBOL(S) ATTACHED TO THE BEGINNING OR END OF A WORD BASE OR PHRASE. FULL TEXT WRITE-IN 0 BLBGD /D/ 07TAB,INDEX INDEX TAB AN INDICATION OF WHETHER OR NOT AN INDEX TAB IS INCLUDED. SELECT REPLY CODE 10AA49 BLBHD /D/ 07STICK,COMPOSING COMPOSING STICK AN INDICATION OF WHETHER OR NOT A COMPOSING STICK IS FURNISHED. SELECT REPLY CODE 10AA55 BLBJD /D/ 07PLATE,DIE DIE PLATE AN INDICATION OF WHETHER OR NOT A DIE PLATE IS INCLUDED. SELECT REPLY CODE 10AA49 BLBKD 11METHOD,PRINTING PRINTING METHOD THE MEANS BY WHICH THE PRINTING IS APPLIED. SELECT REPLY CODE 10AK54 BLBLD /D/ 07SIDE,DROP DROP SIDE AN INDICATION OF WHETHER OR NOT A DROP SIDE IS INCLUDED. SELECT REPLY CODE 10AA49 BLBMA 12QUANTITY,BAND BAND QUANTITY THE NUMBER OF BANDS PROVIDED. 1A MODE REPLY 0 BLBNG 19INSCRIPTION,BAND BAND INSCRIPTION THE INSCRIPTION AFFIXED TO,OR STAMPED ON,THE BAND. FULL TEXT WRITE-IN 0 BLBPG /D/ 19INSCRIPTION,PLATE,DIE DIE PLATE INSCRIPTION THE INSCRIPTION AFFIXED TO,OR STAMPED ON,THE DIE PLATE. FULL TEXT WRITE-IN 0 BLBQA 12QUANTITY,WHEEL,PRINT PRINT WHEEL QUANTITY THE NUMBER OF PRINT WHEEL(S) PROVIDED. 1A MODE REPLY 0 BLBRD /D/ 07LOCK AND KEY LOCK AND KEY AN INDICATION OF WHETHER OR NOT A LOCK AND KEY ARE INCLUDED. SELECT REPLY CODE 10AA49 BLBSD /D/ 07OFFSET,BUILT-IN BUILT-IN OFFSET AN INDICATION OF WHETHER OR NOT A BUILT-IN OFFSET IS INCLUDED. SELECT REPLY CODE 10AA49 BLBTD 11METHOD,ADVANCE ADVANCE METHOD THE MEANS BY WHICH THE ITEM ADVANCES. SELECT REPLY CODE 10AC58 BLBWD 19POSITION,AXLE AXLE POSITION THE POSITION OF THE AXLE IN RELATION TO THE BASE OF THE ITEM. SELECT REPLY CODE 10AA99 BLBXD /D/ 07FEATURE,INDELIBLE INDELIBLE FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES AN INDELIBLE FEATURE. SELECT REPLY CODE 10AA49 BLBYD /D/ 07FEATURE,COLOR,FAST FAST COLOR FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES A FAST COLOR FEATURE. SELECT REPLY CODE 10AA49 BLBZD /D/ 07FEATURE,SOLUBLE,WATER WATER SOLUBLE FEATURE AN INDICATION OF WHETHER OR NOT A WATER SOLUBLE FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BLCBD /D/ 07FEATURE,DUSTLESS DUSTLESS FEATURE AN INDICATION OF WHETHER OR NOT A DUSTLESS FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BLCCD /D/ 07WHEEL,HAND HAND WHEEL AN INDICATION OF WHETHER OR NOT A HAND WHEEL IS INCLUDED. SELECT REPLY CODE 10AA49 BLCDA 12QUANTITY,MORTISE MORTISE QUANTITY THE NUMBER OF MORTISES PROVIDED ON THE ITEM. 1A MODE REPLY 0 BLCFA 12QUANTITY FOR WHICH DESIGNED,ROW,CARD CARD ROW QUANTITY FOR WHICH DESIGNED THE NUMBER OF CARD ROW(S) FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 BLCGA 12QUANTITY,CARD CARD QUANTITY THE NUMBER OF CARD(S) THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 BLCHJ 04WIDTH,MAXIMUM,CARD CARD MAXIMUM WIDTH THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CARD,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BLCJJ 04HEIGHT,MAXIMUM,CARD CARD MAXIMUM HEIGHT THE MAXIMUM MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE CARD,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BLCKD /D/ 07TRAY,DESK DESK TRAY AN INDICATION OF WHETHER OR NOT A DESK TRAY(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BLCLD 07REPLACEABILITY,TIP TIP REPLACEABILITY AN INDICATION OF WHETHER OR NOT THE TIP IS REPLACEABLE. SELECT REPLY CODE 10AG84 BLCMD /D/ 07END,PENETRATING,POINTED POINTED PENETRATING END AN INDICATION OF WHETHER OR NOT A POINTED PENETRATING END IS INCLUDED. SELECT REPLY CODE 10AA49 BLCNA 12QUANTITY,TIER TIER QUANTITY THE NUMBER OF TIERS CONTAINED IN THE ITEM. 1A MODE REPLY 0 BLCPD /D/ 07PLATE,ANCHOR ANCHOR PLATE AN INDICATION OF WHETHER OR NOT AN ANCHOR PLATE IS INCLUDED. SELECT REPLY CODE 10AA49 BLCQD 01COLOR,INK INK COLOR THE HUE OR TINT OF THE INK. SELECT REPLY CODE 10AD06 BLCRD /D/ 07CLIP,POCKET POCKET CLIP AN INDICATION OF WHETHER OR NOT A POCKET CLIP IS PROVIDED. SELECT REPLY CODE 10AB22 BLCSD /D/ 07CLAMP,EXTENSION EXTENSION CLAMP AN INDICATION OF WHETHER OR NOT AN EXTENSION CLAMP IS INCLUDED. SELECT REPLY CODE 10AA49 BLCTA 12QUANTITY,ENGAGER,INTEGRAL HOOK INTEGRAL HOOK ENGAGER QUANTITY THE NUMBER OF INTEGRAL HOOK ENGAGER(S) PROVIDED. 1A MODE REPLY 0 BLCWD /D/ 07BOTTLE,COLOR COLOR BOTTLE AN INDICATION OF WHETHER OR NOT A COLOR BOTTLE IS INCLUDED. SELECT REPLY CODE 10AA49 BLCXD /D/ 07CUP,COLOR COLOR CUP AN INDICATION OF WHETHER OR NOT A COLOR CUP IS INCLUDED. SELECT REPLY CODE 10AA49 BLCYD /D/ 09MATERIAL,BACKBOARD BACKBOARD MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BACKBOARD IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BLCZJ 04DISTANCE BETWEEN ENGAGER BASES DISTANCE BETWEEN ENGAGER BASES THE DISTANCE BETWEEN ENGAGER BASES. 2D AND 1B MODE REPLY21AA051AC20 BLDBD /D/ 01COLOR,BACKBOARD BACKBOARD COLOR THE HUE OR TINT OF THE BACKBOARD. SELECT REPLY CODE 10AD06 BLDCJ 04LENGTH,FOCAL,NOMINAL,REAR COMPONENT REAR COMPONENT NOMINAL FOCAL LENGTH A MEASUREMENT OF THE LONGEST NOMINAL FOCAL DIMENSION OF THE REAR COMPONENT,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BLDDG 19COVERAGE,VIEW,FIELD FIELD VIEW COVERAGE THE FILM/AREA SIZE THAT THE LENS TRANSPOSES RELATIVE TO ITS FIELD OF VIEW COVERED. FULL TEXT WRITE-IN 0 BLDFD 08LOCATION,SHUTTER SHUTTER LOCATION INDICATES THE LOCATION OF THE SHUTTER ON THE ITEM. SELECT REPLY CODE 10AJ91 BLDGG 10SPEED,MARKED MARKED SPEED AN INDICATION OF THE MARKED SPEED OF THE ITEM. FULL TEXT WRITE-IN 0 BLDHD /D/ 18TYPE,RANGE,DIAPHRAGM APERTURE DIAPHRAGM APERTURE RANGE TYPE INDICATES THE TYPE OF DIAPHRAGM APERTURE RANGE PROVIDED ON THE ITEM. SELECT REPLY CODE 10AK54 BLDJG /D/ 10RANGE,APERTURE,MARKED MARKED APERTURE RANGE THE MINIMUM AND MAXIMUM MARKINGS ON THE ITEM INDICATING THE LIMITS OF THE APERTURE. FULL TEXT WRITE-IN 0 BLDKD /D/ 07FEATURE,CONVERTIBLE,LENS SPEED LENS SPEED CONVERTIBLE FEATURE AN INDICATION OF WHETHER OR NOT A LENS SPEED CONVERTIBLE FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BLDLJ A10SPEED,COMPONENT,FRONT FRONT COMPONENT SPEED AN INDICATION OF THE SPEED OF THE FRONT COMPONENT. 1D AND 1A MODE REPLY12AL77 BLDMJ A10SPEED,COMPONENT,REAR REAR COMPONENT SPEED AN INDICATION OF THE SPEED OF THE REAR COMPONENT. 1D AND 1A MODE REPLY12AL77 BLDND 19POSITION,VIEWING VIEWING POSITION THE POSITION FROM WHICH THE ITEM IS TO BE VIEWED. SELECT REPLY CODE 10AM04 BLDPD 19POSITION,IMAGE IMAGE POSITION AN INDICATION OF THE POSITION OF THE IMAGE. SELECT REPLY CODE 10AK54 BLDQD /D/ 07LENS,REMOVABLE REMOVABLE LENS AN INDICATION OF WHETHER OR NOT A REMOVABLE LENS(ES) IS INCLUDED. SELECT REPLY CODE 10AA49 BLDRG 10STRENGTH,DIOPTER DIOPTER STRENGTH THE AMOUNT OF STRENGTH OF THE DIOPTER. FULL TEXT WRITE-IN 0 BLDSD 01COLOR,TINT TINT COLOR THE COLOR USED TO TINT THE ITEM. SELECT REPLY CODE 10AD06 BLDTD /D/ 09MATERIAL,COATING,REFLECTIVE REFLECTIVE COATING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ITEM IS COATED TO INDUCE REFLECTION,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BLDWD /D/ 07BACKING,RESISTANT,HEAT HEAT RESISTANT BACKING AN INDICATION OF WHETHER OR NOT A HEAT RESISTANT BACKING IS INCLUDED. SELECT REPLY CODE 10AA49 BLDXD /D/ 07FEATURE,RESISTANT,HEAT HEAT RESISTANT FEATURE AN INDICATION OF WHETHER OR NOT A HEAT RESISTANT FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BLDYD /D/ 07ADJUSTMENT,PARALLAX,MASKED MASKED PARALLAX ADJUSTMENT AN INDICATION OF WHETHER OR NOT A MASKED PARALLAX ADJUSTMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BLDZD /D/ 07CORRECTOR,PARALLAX,AUTOMATIC AUTOMATIC PARALLAX CORRECTOR AN INDICATION OF WHETHER OR NOT AN AUTOMATIC PARALLAX CORRECTOR IS INCLUDED. SELECT REPLY CODE 10AA49 BLFBD 18TYPE,SHUTTER SHUTTER TYPE INDICATES THE TYPE OF SHUTTER PROVIDED. SELECT REPLY CODE 10AM07 BLFCG /D/ 10RANGE,SPEED,ADJUSTABLE SHUTTER ADJUSTABLE SHUTTER SPEED RANGE AN INDICATION OF THE MINIMUM TO MAXIMUM SPEED OF THE ADJUSTABLE SHUTTER. FULL TEXT WRITE-IN 0 BLFDA 10SPEED,SHUTTER,FIXED FIXED SHUTTER SPEED AN INDICATION OF THE FIXED SHUTTER SPEED OF THE ITEM. 1A MODE REPLY 0 BLFFD /D/ 07FEATURE,SYNCHRONIZATION SYNCHRONIZATION FEATURE AN INDICATION OF WHETHER OR NOT A SYNCHRONIZATION FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BLFGD 19MEDIA FOR WHICH DESIGNED,FLASH FLASH MEDIA FOR WHICH DESIGNED INDICATES THE TYPE OF FLASH FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AD34 BLFHG /D/ 10RANGE,FOCUSING FOCUSING RANGE THE MINIMUM AND MAXIMUM DISTANCE THE ITEM CAN BE FOCUSED. FULL TEXT WRITE-IN 0 BLFJD /D/ 07DIAPHRAGM DIAPHRAGM AN INDICATION OF WHETHER OR NOT A DIAPHRAGM IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BLFKD /D/ 07BOARD,LENS LENS BOARD AN INDICATION OF WHETHER OR NOT A LENS BOARD IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BLFLJ 04DIAMETER FOR WHICH DESIGNED,BARREL,LENS LENS BARREL DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LENS BARREL FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BLFMG /D/ 18TYPE AND QUANTITY,KNOB,CONTROL CONTROL KNOB TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF CONTROL KNOB(S) PROVIDED. FULL TEXT WRITE-IN 0 BLFND /D/ 07HOLDER,FILTER FILTER HOLDER AN INDICATION OF WHETHER OR NOT A FILTER HOLDER IS INCLUDED. SELECT REPLY CODE 10AA49 BLFPA /D/ 19DATE,DOCUMENT DOCUMENT DATE THE DATE OF THE PRINTED DOCUMENT. 1A MODE REPLY 0 BLFQD /D/ 03DESIGNATOR,SIZE,ROLL ROLL SIZE DESIGNATOR THE SIZE DESIGNATION BY WHICH THE ROLL IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. SELECT REPLY CODE 10AF81 BLFRD 19POSITION,CAMERA,MOUNTED MOUNTED CAMERA POSITION THE POSITION OF THE CAMERA WHEN MOUNTED. SELECT REPLY CODE 10AF63 BLFSD /D/ 07FEATURE,STABILIZATION,HORIZONTAL HORIZONTAL STABILIZATION FEATURE AN INDICATION OF WHETHER OR NOT A HORIZONTAL STABILIZATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BLFTD 19CHARACTERISTICS,ADJUSTABLE ADJUSTABLE CHARACTERISTICS AN INDICATION OF THE ADJUSTABLE CHARACTERISTICS OF THE ITEM. SELECT REPLY CODE 10AJ41 BLFWB 10ROTATION IN DEG ROTATION IN DEG THE MEASUREMENT OF ROTATION,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BLFXD /D/ 07VIEWFINDER,BUILT-IN BUILT-IN VIEWFINDER AN INDICATION OF WHETHER OR NOT A BUILT-IN VIEWFINDER IS INCLUDED. SELECT REPLY CODE 10AA49 BLFYD /D/ 07FEATURE,ATTACHMENT,INSTANTANEOUS INSTANTANEOUS ATTACHMENT FEATURE AN INDICATION OF WHETHER OR NOT AN INSTANTANEOUS ATTACHMENT FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BLFZG 18TYPE,MOUNTING,LENS LENS MOUNTING TYPE INDICATES THE TYPE OF LENS MOUNTING PROVIDED. FULL TEXT WRITE-IN 0 BLGBD 18TYPE,POST,CENTER CENTER POST TYPE INDICATES THE TYPE OF CENTER POST INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AL76 BLGCD /D/ 07CONTROL,COLUMN,ELEVATOR ELEVATOR COLUMN CONTROL AN INDICATION OF WHETHER OR NOT AN ELEVATOR COLUMN CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 BLGDJ T04SIZE,BACKBOARD BACKBOARD SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE BACKBOARD. 1D AND 1F MODE REPLY11AA05 BLGFJ 04DISTANCE BETWEEN POST TOP AND ADJACENT ENGAGER BASE DISTANCE BETWEEN POST TOP AND ADJACENT ENGAGER BASE THE DISTANCE BETWEEN THE TOP OF THE POST AND THE ADJACENT ENGAGER BASE. 2D AND 1B MODE REPLY21AA051AC20 BLGGA 12QUANTITY,LEG,SUPPORT SUPPORT LEG QUANTITY THE NUMBER OF SUPPORT LEG(S) PROVIDED. 1A MODE REPLY 0 BLGHJ T04SIZE ACCOMMODATED,PAD,PAPER PAPER PAD SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE PAPER PAD ACCOMMODATED. 1D AND 1F MODE REPLY11AA05 BLGJD 19FEATURE,COATING COATING FEATURE AN INDICATION OF THE COATING FEATURE ON THE ITEM. SELECT REPLY CODE 10AG57 BLGKD /D/ 07FEATURE,REFLECTORIZED REFLECTORIZED FEATURE AN INDICATION OF WHETHER OR NOT A REFLECTORIZED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BLGLD 19PROCESS FOR WHICH DESIGNED,PRINTING PRINTING PROCESS FOR WHICH DESIGNED THE PRINTING PROCESS FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AH21 BLGMJ /D/ 04HEIGHT,POCKET/CARD POCKET/CARD HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A POCKET OR CARD,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BLGNJ /D/ 04WIDTH,POCKET/CARD POCKET/CARD WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A POCKET OR CARD,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BLGPD 18TYPE,LENS LENS TYPE INDICATES THE TYPE OF LENS PROVIDED ON THE ITEM. SELECT REPLY CODE 10AM04 BLGQD 14SHAPE,LENS LENS SHAPE THE PHYSICAL CONFIGURATION OF THE LENS. SELECT REPLY CODE 10AD07 BLGRJ 04DIAMETER,EFFECTIVE,LENS LENS EFFECTIVE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LENS EFFECTIVE AREA,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BLGSJ A12QUANTITY ACCOMMODATED,SLIDE SLIDE QUANTITY ACCOMMODATED THE NUMBER OF SLIDE(S) THE ITEM WILL ACCOMMODATE. 1D AND 1A MODE REPLY11AC20 BLGTJ /D/ 04LENGTH,BAR,SLOTTED SLOTTED BAR LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SLOTTED BAR,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BLGWJ /D/ 04WIDTH,BAR BAR WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BAR,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BLGXD /D/ 09MATERIAL,MOUNT,FLEXIBLE FLEXIBLE MOUNT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FLEXIBLE MOUNT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BLGYJ /D/ 04WIDTH AND LOCATION,LEG LEG WIDTH AND LOCATION A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A LEG,IN DISTINCTION FROM THICKNESS,AND ITS LOCATION. 3D AND 1B MODE REPLY31AA051AC203AJ91 BLGZJ 04HEIGHT,FRAME FRAME HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A FRAME,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BLHBJ 04THICKNESS,FRAME FRAME THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A FRAME,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BLHCD /D/ 09MATERIAL,CLOTH,WIRE WIRE CLOTH MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WIRE CLOTH IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH ISAC IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 BLHDD /D/ 17SURFACE TREATMENT,CLOTH,WIRE WIRE CLOTH SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE WIRE CLOTH SURFACE. PLEASE USE MRC SFTT WITH ISAC IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 BLHFJ 04DIAMETER,OVERALL,FRAME FRAME OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF A FRAME. 2D AND 1B MODE REPLY21AA051AC20 BLHGA 12QUANTITY PER SIDE QUANTITY PER SIDE THE NUMBER OF ITEM(S) ACCOMMODATED PER SIDE. 1A MODE REPLY 0 BLHHJ 04WIDTH,OVERALL,FRAME FRAME OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FRAME,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BLHJJ 04HEIGHT,OVERALL,FRAME FRAME OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE FRAME. 2D AND 1B MODE REPLY21AA051AC20 BLHKJ 04THICKNESS,OVERALL,FRAME FRAME OVERALL THICKNESS AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF THE FRAME,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BLHLJ 10CAPACITY,STEAM STEAM CAPACITY THE AMOUNT OF STEAM FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY22AG671AC20 BLHMJ 04DIAMETER,OPENING,FRAME FRAME OPENING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FRAME OPENING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BLHND 19CONSTRUCTION,HEADER HEADER CONSTRUCTION THE STRUCTURAL CHARACTERISTIC(S) OF THE HEADER. SELECT REPLY CODE 10AL59 BLHPJ 04WIDTH,OPENING,FRAME FRAME OPENING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FRAME OPENING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BLHQJ 10TEMP RATING,STEAM,SUPERHEATED MAXIMUM MAXIMUM SUPERHEATED STEAM TEMP RATING THE MAXIMUM SUPERHEATED STEAM TEMPERATURE FOR WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY12AB49 BLHRJ 04HEIGHT,OPENING,FRAME FRAME OPENING HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE FRAME OPENING,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BLHSA 12QUANTITY,BURNER,OIL OIL BURNER QUANTITY THE NUMBER OF OIL BURNERS PROVIDED WITH THE ITEM. 1A MODE REPLY 0 BLHTD /D/ 07HOLES,MOUNTING,FRAME FRAME MOUNTING HOLES AN INDICATION OF WHETHER OR NOT FRAME MOUNTING HOLES ARE INCLUDED. SELECT REPLY CODE 10AA49 BLHWA /D/ 12QUANTITY,STOKER STOKER QUANTITY THE NUMBER OF STOKER(S) PROVIDED. 1A MODE REPLY 0 BLHXD /D/ 07WATERWALLS WATERWALLS AN INDICATION OF WHETHER OR NOT WATERWALLS ARE PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AB22 BLHYD /D/ 07FEATURE,CIRCULATION,FORCED FORCED CIRCULATION FEATURE AN INDICATION OF WHETHER OR NOT A FORCED CIRCULATION FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BLHZD 19POSITION,BAR BAR POSITION AN INDICATION OF THE POSITION OF THE BAR/S/. SELECT REPLY CODE 10AF63 BLJBG 04SPACING,BAR BAR SPACING THE NARRATIVE EXPRESSION USED FOR INDICATING THE SPACING BETWEEN THE BARS. FULL TEXT WRITE-IN 0 BLJCD 11METHOD,IGNITION IGNITION METHOD THE MEANS USED FOR PURPOSES OF IGNITING. SELECT REPLY CODE 10AC58 BLJDG 18TYPE,NETWORK NETWORK TYPE INDICATES THE TYPE OF NETWORK PROVIDED. FULL TEXT WRITE-IN 0 BLJFJ 10IMPEDANCE,INPUT,NOMINAL,NETWORK NETWORK NOMINAL INPUT IMPEDANCE THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) WHICH THE NETWORK OFFERS TO THE INPUT FLOW OF ALTERNATING CURRENT. 1D AND 1B MODE REPLY11AA57 BLJGD /D/ 07FACILITIES,MOUNTING,SWITCH SWITCH MOUNTING FACILITIES AN INDICATION OF WHETHER OR NOT SWITCH MOUNTING FACILITIES ARE INCLUDED. SELECT REPLY CODE 10AA49 BLJHD /D/ 07FACILITIES,MOUNTING,DIAL DIAL MOUNTING FACILITIES AN INDICATION OF WHETHER OR NOT DIAL MOUNTING FACILITIES ARE INCLUDED. SELECT REPLY CODE 10AA49 BLJLD /D/ 07FEATURE,ADJUSTABILITY,HEIGHT HEIGHT ADJUSTABILITY FEATURE AN INDICATION OF WHETHER OR NOT A HEIGHT ADJUSTABILITY FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BLJMJ 04HEIGHT,MINIMUM MINIMUM HEIGHT THE MINIMUM MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE ITEM,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BLJNG 19AGENCY,CONTROLLING,CONNECTOR CONNECTOR CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE CONNECTOR. FULL TEXT WRITE-IN 0 BLJPG 11METHOD,ATTACHMENT,INSULATOR INSULATOR ATTACHMENT METHOD THE MEANS USED TO ATTACH THE INSULATOR. FULL TEXT WRITE-IN 0 BLJQD /D/ 07DEVICE,ATTACHMENT,SEPARATE INSULATOR SEPARATE INSULATOR ATTACHMENT DEVICE AN INDICATION OF WHETHER OR NOT A SEPARATE INSULATOR ATTACHMENT DEVICE IS PROVIDED. SELECT REPLY CODE 10AB22 BLJRD /D/ 07FEATURE,CLAMPING,MOUNTING BOLT MOUNTING BOLT CLAMPING FEATURE AN INDICATION OF WHETHER OR NOT A MOUNTING BOLT CLAMPING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BLJSJ T04DIAMETER RANGE ACCOMMODATED,STRAND STRAND DIAMETER RANGE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE DIAMETER LIMITS OF THE STRAND,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1F MODE REPLY11AA05 BLJTA 12QUANTITY ACCOMMODATED,RESISTOR RESISTOR QUANTITY ACCOMMODATED THE NUMBER OF RESISTORS THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 BLJWJ 04DISTANCE BETWEEN FERRULES DISTANCE BETWEEN FERRULES THE DISTANCE BETWEEN THE FERRULES. 2D AND 1B MODE REPLY21AA051AC20 BLJXD /D/ 09MATERIAL,CLIP CLIP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CLIP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BLJYD /D/ 07STOPS,END END STOPS AN INDICATION OF WHETHER OR NOT END STOPS ARE INCLUDED. SELECT REPLY CODE 10AA49 BLJZD 18TYPE,MOUNTING,BASE BASE MOUNTING TYPE INDICATES THE TYPE OF BASE MOUNTING PROVIDED. SELECT REPLY CODE 10AA78 BLKBD 18TYPE ACCOMMODATED,INSULATOR INSULATOR TYPE ACCOMMODATED INDICATES THE TYPE OF INSULATOR THE ITEM IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AK54 BLKCG 18TYPE,THREAD THREAD TYPE INDICATES THE TYPE OF THREADS PROVIDED. FULL TEXT WRITE-IN 0 BLKDJ 04DIAMETER ACCOMMODATED,CABLE CABLE DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE CABLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BLKFD /D/ 07THIMBLE,REMOVABLE REMOVABLE THIMBLE AN INDICATION OF WHETHER OR NOT A REMOVABLE THIMBLE IS INCLUDED. SELECT REPLY CODE 10AA49 BLKGJ 04LENGTH,BASE,ABOVE ABOVE BASE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION ABOVE THE BASE OF AN ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BLKHJ 04LENGTH,BASE,BELOW BELOW BASE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION BELOW THE BASE OF AN ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BLKJG 13THREAD DIAMETER,MOUNTING,INSULATOR INSULATOR MOUNTING THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED INSULATOR MOUNTING,AND TERMINATES AT THE CIRCUMFERENCE. FULL TEXT WRITE-IN 0 BLKKA 12QUANTITY,HUB HUB QUANTITY THE NUMBER OF HUBS PROVIDED. 1A MODE REPLY 0 BLKLD /D/ 07ENTRANCE,WIRING,OPEN OPEN WIRING ENTRANCE AN INDICATION OF WHETHER OR NOT AN OPEN WIRING ENTRANCE IS PROVIDED. SELECT REPLY CODE 10AB22 BLKMA 12QUANTITY,RING,CONTACT CONTACT RING QUANTITY THE NUMBER OF CONTACT RINGS PROVIDED. 1A MODE REPLY 0 BLKND /D/ 09MATERIAL,SURFACE,RING RING SURFACE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE RING(S) SURFACE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BLKPA 12QUANTITY,HOLDER,BRUSH BRUSH HOLDER QUANTITY THE NUMBER OF BRUSH HOLDERS PROVIDED. 1A MODE REPLY 0 BLKQD /D/ 18TYPE,CONTACT,INPUT INPUT CONTACT TYPE INDICATES THE TYPE OF INPUT CONTACT PROVIDED. SELECT REPLY CODE 10AN56 BLKRD 03DESIGNATION,SERIES,OUTPUT COAXIAL CONNECTION OUTPUT COAXIAL CONNECTION SERIES DESIGNATION A LETTER OR GROUP OF LETTERS USED TO DESIGNATE THE PARTICULAR OUTPUT COAXIAL CONNECTED SERIES. SELECT REPLY CODE 10AF42 BLKSD /D/ 18TYPE,CONTACT,OUTPUT OUTPUT CONTACT TYPE INDICATES THE TYPE OF OUTPUT CONTACT PROVIDED. SELECT REPLY CODE 10AN56 BLKWG /D/ 11METHOD,ATTACHMENT,SUPPORTED OBJECT/SURFACE SUPPORTED OBJECT/SURFACE ATTACHMENT METHOD THE MEANS USED IN ATTACHING THE SUPPORTED OBJECT OR SURFACE. FULL TEXT WRITE-IN 0 BLKXB 10SWING IN DEG,JOINT,BALL/SWIVEL BALL/SWIVEL JOINT SWING IN DEG AN INDICATION OF THE BALL OR SWIVEL JOINT SWING,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BLKYD 19POSITION,HUB HUB POSITION AN INDICATION OF THE POSITION OF THE HUB ON THE ITEM. SELECT REPLY CODE 10AF63 BLKZJ 04DIAMETER,STUD,MOUNTING MOUNTING STUD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING STUD,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BLLBA 12QUANTITY ACCOMMODATED,PLATE,CRYSTAL CRYSTAL PLATE QUANTITY ACCOMMODATED THE NUMBER OF CRYSTAL PLATES THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 BLLCD 08LOCATION,ADJUSTMENT,AIR GAP AIR GAP ADJUSTMENT LOCATION INDICATES THE LOCATION OF THE ADJUSTMENT ON THE AIR GAP. SELECT REPLY CODE 10AJ91 BLLDJ /D/ 10CLEARANCE,TRUCK,VERTICAL,MINIMUM MINIMUM VERTICAL TRUCK CLEARANCE THE MINIMUM VERTICAL TRUCK CLEARANCE OF THE ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1D AND 1B MODE REPLY11AA05 BLLFD /D/ 09MATERIAL,BIN BIN MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BIN IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BLLGD /D/ 11METHOD,SUPPLY,CHARGING MATERIAL CHARGING MATERIAL SUPPLY METHOD THE MEANS UTILIZED TO SUPPLY CHARGING MATERIAL TO THE ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AE35 BLLHD /D/ 07BATCHER,WEIGHING WEIGHING BATCHER AN INDICATION OF WHETHER OR NOT A WEIGHING BATCHER IS INCLUDED. SELECT REPLY CODE 10AA49 BLLJJ 10CAPACITY,BATCHER,WEIGHING WEIGHING BATCHER CAPACITY THE CAPACITY OF THE WEIGHING BATCHER. 2D AND 1B MODE REPLY22AG671AC20 BLLKD /D/ 07ELEVATOR ELEVATOR AN INDICATION OF WHETHER OR NOT AN ELEVATOR IS FURNISHED. SELECT REPLY CODE 10AA55 BLLLJ /D/ 10CAPACITY,ELEVATOR ELEVATOR CAPACITY THE CAPACITY OF THE ELEVATOR. 1D AND 1B MODE REPLY12AG67 BLLMJ /D/ 04DISTANCE BETWEEN ELEVATOR SPROCKETS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN ELEVATOR SPROCKETS THE CENTER TO CENTER DISTANCE BETWEEN THE ELEVATOR SPROCKETS. 2D AND 1B MODE REPLY21AA051AC20 BLLND 18TYPE,GATE,DISCHARGE DISCHARGE GATE TYPE INDICATES THE TYPE OF DISCHARGE GATE. SELECT REPLY CODE 10AC57 BLLPG /D/ 04SIZE,OPENING,DISCHARGE GATE DISCHARGE GATE OPENING SIZE DESIGNATES THE SIZE OF THE DISCHARGE GATE OPENING. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. FULL TEXT WRITE-IN 0 BLLQJ /D/ 10CAPACITY,BIN BIN CAPACITY THE CAPACITY OF THE BIN. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1D AND 1B MODE REPLY12AG67 BLLRJ 10CAPACITY,MAXIMUM MAXIMUM CAPACITY THE MAXIMUM CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BLLSD /D/ 07WHEEL,FIFTH FIFTH WHEEL AN INDICATION OF WHETHER OR NOT A FIFTH WHEEL IS INCLUDED. SELECT REPLY CODE 10AA49 BLLTD /D/ 07JACKLEG,ADJUSTABLE ADJUSTABLE JACKLEG AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE JACKLEG(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BLLWD /D/ 18TYPE,DRIVE,DRUM DRUM DRIVE TYPE INDICATES THE TYPE OF DRIVE FOR TURNING,ROTATING,OR POSITIONING THE DRUM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AG25 BLLXD /D/ 18TYPE,DISCHARGE,DRUM DRUM DISCHARGE TYPE INDICATES THE TYPE OF DRUM DISCHARGE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AH76 BLLYD 18TYPE,BURNER BURNER TYPE INDICATES THE TYPE OF BURNER PROVIDED. SELECT REPLY CODE 10AB75 BLLZG /D/ 10HORSEPOWER REQUIRED AT SPECIFIED RPM HORSEPOWER REQUIRED AT SPECIFIED RPM THE HORSEPOWER REQUIRED TO START AND OPERATE THE ITEM AT SPECIFIED REVOLUTIONS PER MINUTE. FULL TEXT WRITE-IN 0 BLMBD /D/ 07DIVIDER,REMOVABLE,COMPARTMENT COMPARTMENT REMOVABLE DIVIDER AN INDICATION OF WHETHER OR NOT A COMPARTMENT REMOVABLE DIVIDER IS INCLUDED. SELECT REPLY CODE 10AA49 BLMCJ 04LENGTH,OPENING,DISCHARGE GATE DISCHARGE GATE OPENING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A DISCHARGE GATE OPENING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BLMDJ 04WIDTH,OPENING,DISCHARGE GATE DISCHARGE GATE OPENING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A DISCHARGE GATE OPENING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BLMFD /D/ 07SUPPORT SUPPORT AN INDICATION OF WHETHER OR NOT A SUPPORT IS PROVIDED. SELECT REPLY CODE 10AB22 BLMGA /D/ 12QUANTITY,ACCOMMODATION,LENS LENS ACCOMMODATION QUANTITY THE NUMBER OF LENS(ES) THAT CAN BE ACCOMMODATED BY THE ITEM. 1A MODE REPLY 0 BLMHJ 10CLEARANCE,MINIMUM,LATERAL TRUCK SUPPORT LATERAL TRUCK SUPPORT MINIMUM CLEARANCE THE MINIMUM LATERAL TRUCK CLEARANCE MEASURED BETWEEN THE SUPPORTS. 1D AND 1B MODE REPLY11AA05 BLMJJ 10CLEARANCE,MINIMUM,VERTICAL TRUCK SUPPORT VERTICAL TRUCK SUPPORT MINIMUM CLEARANCE THE MINIMUM VERTICAL TRUCK CLEARANCE MEASURED FROM THE GROUND TO THE SUPPORT. 1D AND 1B MODE REPLY11AA05 BLMKJ 10CLEARANCE,MAXIMUM,LATERAL TRUCK SUPPORT LATERAL TRUCK SUPPORT MAXIMUM CLEARANCE THE MAXIMUM LATERAL TRUCK CLEARANCE MEASURED BETWEEN THE SUPPORTS. 1D AND 1B MODE REPLY11AA05 BLMLJ 10CLEARANCE,MAXIMUM,VERTICAL TRUCK SUPPORT VERTICAL TRUCK SUPPORT MAXIMUM CLEARANCE THE MAXIMUM VERTICAL TRUCK CLEARANCE MEASURED FROM THE GROUND TO THE SUPPORT. 1D AND 1B MODE REPLY11AA05 BLMMA /D/ 12QUANTITY,CONVEYOR CONVEYOR QUANTITY THE NUMBER OF CONVEYOR(S) PROVIDED. 1A MODE REPLY 0 BLMNG /D/ 04SIZE,BELT,CONVEYOR CONVEYOR BELT SIZE DESIGNATES THE SIZE OF THE BELT ON THE CONVEYOR. FULL TEXT WRITE-IN 0 BLMPD /D/ 19SOURCE,POWER,CONVEYOR CONVEYOR POWER SOURCE THE SOURCE OF POWER UTILIZED TO OPERATE THE CONVEYOR. SELECT REPLY CODE 10AG27 BLMQD /D/ 07JACKLEG,TRAILER TRAILER JACKLEG AN INDICATION OF WHETHER OR NOT A TRAILER JACKLEG(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BLMRD 18TYPE,TIRE,TRAILER TRAILER TIRE TYPE INDICATES THE TYPE OF TIRE PROVIDED ON THE TRAILER. SELECT REPLY CODE 10AH67 BLMSA /D/ 16STYLE,ARRANGEMENT,TRAILER WHEEL TRAILER WHEEL ARRANGEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE TRAILER WHEELS. 1A MODE REPLY 0 BLMTD 18TYPE,DRUM DRUM TYPE INDICATES THE TYPE OF DRUM PROVIDED. SELECT REPLY CODE 10AG25 BLMWD 08LOCATION,OPENING,DISCHARGE DISCHARGE OPENING LOCATION INDICATES THE LOCATION OF THE DISCHARGE OPENING ON THE ITEM. SELECT REPLY CODE 10AJ91 BLMXD 11METHOD,DISCHARGING DISCHARGING METHOD THE MEANS USED FOR DISCHARGING THE ITEM. SELECT REPLY CODE 10AL88 BLMYD /D/ 07TANK,WATER WATER TANK AN INDICATION OF WHETHER OR NOT A WATER TANK IS INCLUDED. SELECT REPLY CODE 10AA49 BLMZB /D/ 10HORSEPOWER REQUIRED,DRAWBAR,MINIMUM MINIMUM DRAWBAR HORSEPOWER REQUIRED THE MINIMUM DRAWBAR HORSEPOWER REQUIRED TO TOW THE ITEM. 1B MODE REPLY 0 BLNBJ 04WIDTH,CUTTING CUTTING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE CUTTING LENGTH OF THE ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BLNCJ 04DIAMETER,INSIDE,BOTTOM BOTTOM INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOTTOM OF THE ITEM,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BLNDD /D/ 09MATERIAL,BAIL BAIL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BAIL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BLNFD /D/ 17SURFACE TREATMENT,BAIL BAIL SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE BAIL SURFACE. SELECT REPLY CODE 10AD09 BLNGA 12QUANTITY,LIP,POURING POURING LIP QUANTITY THE NUMBER OF POURING LIP(S) PROVIDED. 1A MODE REPLY 0 BLNHD /D/ 07FEATURE,ACIDPROOF ACIDPROOF FEATURE AN INDICATION OF WHETHER OR NOT AN ACIDPROOF FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BLNJA /D/ 12QUANTITY,COAT,ENAMEL ENAMEL COAT QUANTITY THE NUMBER OF COAT(S) OF ENAMEL PROVIDED. 1A MODE REPLY 0 BLNKJ 04DIAMETER,OUTSIDE,TOP TOP OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TOP OF THE ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BLNLB 04ANGLE IN DEG,SPOUT,OFFSET OFFSET SPOUT ANGLE IN DEG THE ANGLE OF THE OFFSET SPOUT,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BLNMD /D/ 07END,THREADED,SPOUT SPOUT THREADED END AN INDICATION OF WHETHER OR NOT A THREADED END IS INCLUDED ON THE SPOUT. SELECT REPLY CODE 10AA49 BLNNJ 04LENGTH,SPOUT SPOUT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SPOUT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BLNPD /D/ 07VALVE,GATE GATE VALVE AN INDICATION OF WHETHER OR NOT A GATE VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 BLNQJ 04DIAMETER,OPENING,SPOUT SPOUT OPENING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SPOUT OPENING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BLNRJ 04DIAMETER,OPENING,FILL FILL OPENING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FILL OPENING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BLNSD /D/ 07SPOUT,POURING,FLEXIBLE FLEXIBLE POURING SPOUT AN INDICATION OF WHETHER OR NOT A FLEXIBLE POURING SPOUT IS INCLUDED. SELECT REPLY CODE 10AA49 BLNTD 07REMOVABILITY,SPOUT SPOUT REMOVABILITY AN INDICATION OF WHETHER OR NOT THE SPOUT IS REMOVABLE. SELECT REPLY CODE 10AC29 BLNWG /D/ 19AGENCY,CONTROLLING,TERMINAL TERMINAL CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE TERMINAL. FULL TEXT WRITE-IN 0 BLNXJ /D/A19NUMBER,IDENTIFYING,TERMINAL TERMINAL IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE TERMINAL. 1D AND 1A MODE REPLY12AG99 BLNYD /D/ 11METHOD,CODING CODING METHOD THE MEANS USED TO EXPRESS SYSTEMATIC WORDS OR OTHER SYMBOLS FOR COMMUNICATION PERTAINING TO AN ITEM. SELECT REPLY CODE 10AN32 BLNZA 12QUANTITY PER CONDUCTOR,STRAND STRAND QUANTITY PER CONDUCTOR THE NUMBER OF STRANDS PER CONDUCTOR. 1A MODE REPLY 0 BLPBD 18TYPE,CONDUIT CONDUIT TYPE INDICATES THE TYPE OF CONDUIT. SELECT REPLY CODE 10AK93 BLPCJ /D/ 04SIZE,STRAND STRAND SIZE DESIGNATES THE WIRE GAGE AND THE GAGE NUMBER USED TO DESCRIBE THE STRAND SIZE. 1D AND 1B MODE REPLY12AG67 BLPDG /D/ 19TERMINATION,FITTING,END END FITTING TERMINATION A NARRATIVE EXPRESSION USED TO INDICATE THE END FITTING TERMINATION(S). FULL TEXT WRITE-IN 0 BLPFG /D/ 19CODING AND QUANTITY,CONDUCTOR CONDUCTOR CODING AND QUANTITY THE COLOR OR OTHER CODING METHOD USED TO IDENTIFY THE PURPOSE OR FUNCTION OF A CONDUCTOR AND THE NUMBER OF CONDUCTORS CODED. FULL TEXT WRITE-IN 0 BLPGG 19AGENCY,CONTROLLING,REEL REEL CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION THAT CONTROLS THE MANUFACTURE OF THE REEL. FULL TEXT WRITE-IN 0 BLPHD /D/ 07HOLDER,REEL REEL HOLDER AN INDICATION OF WHETHER OR NOT A REEL HOLDER(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BLPJD /D/ 09MATERIAL,STRAP STRAP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE STRAP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BLPKD 18TYPE,DEVICE,OPTICAL OPTICAL DEVICE TYPE INDICATES THE TYPE OF OPTICAL DEVICE USED. SELECT REPLY CODE 10AM07 BLPLD /D/ 07SCALE,DIOPTER DIOPTER SCALE AN INDICATION OF WHETHER OR NOT A DIOPTER SCALE IS INCLUDED. SELECT REPLY CODE 10AA49 BLPMJ 04DIAMETER,APERTURE,OBJECTIVE OBJECTIVE APERTURE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OBJECTIVE APERTURE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BLPND 18TYPE,FOCUSING,EYEPIECE EYEPIECE FOCUSING TYPE INDICATES THE TYPE OF FOCUSING PROVIDED ON THE EYEPIECE. SELECT REPLY CODE 10AH21 BLPPD /D/ 07FEATURE,ADJUSTMENT,INTERPUPILLARY INTERPUPILLARY ADJUSTMENT FEATURE AN INDICATION OF WHETHER OR NOT AN INTERPUPILLARY ADJUSTMENT FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BLPQD 18TYPE,MAGNIFICATION MAGNIFICATION TYPE INDICATES THE TYPE OF MAGNIFICATION PROVIDED. SELECT REPLY CODE 10AC01 BLPRJ A19MAGNIFICATION MAGNIFICATION THE POWER AND/OR AMOUNT OF APPARENT ENLARGEMENT BY AN OPTICAL DEVICE. 1D AND 1A MODE REPLY11AC20 BLPSJ 04LENGTH,OVERALL,STRAIGHT TYPE STRAIGHT TYPE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF A STRAIGHT TYPE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BLPTJ 04LENGTH,OVERALL,OPEN DRAWTUBE OPEN DRAWTUBE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE OPEN DRAWTUBE. 2D AND 1B MODE REPLY21AA051AC20 BLPWD /D/ 07MARKINGS,SCALE SCALE MARKINGS AN INDICATION OF WHETHER OR NOT SCALE MARKINGS ARE PROVIDED. SELECT REPLY CODE 10AB22 BLPXL 16STYLE DESIGNATOR,RETICLE RETICLE STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE RETICLE. 1L MODE REPLY 0 BLPYA 19NUMBER,IDENTIFYING,RETICLE RETICLE IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE RETICLE. 1A MODE REPLY 0 BLPZD 08LOCATION,RETICLE RETICLE LOCATION INDICATES THE LOCATION OF THE RETICLE ON THE ITEM. SELECT REPLY CODE 10AJ91 BLQBA 19NUMBER,MODEL,INSTRUMENT LIGHT INSTRUMENT LIGHT MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE INSTRUMENT LIGHT. 1A MODE REPLY 0 BLQCD 19ARRANGEMENT,LENS LENS ARRANGEMENT THE ARRANGEMENT OF THE ASSEMBLED LENS(ES). SELECT REPLY CODE 10AH86 BLQDJ /D/ 04WIDTH,PORTION,ACTIVE ACTIVE PORTION WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ACTIVE PORTION OF AN ITEM,IN DISTINCTION FROM THE THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BLQFD 11METHOD,CONNECTION,INDICATOR INDICATOR CONNECTION METHOD THE MEANS USED TO CONNECT THE INDICATOR. SELECT REPLY CODE 10AJ68 BLQGJ 04LENGTH,TUBE,FLEXIBLE FLEXIBLE TUBE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FLEXIBLE TUBE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BLQHD /D/ 07SOCKET,SEPARABLE SEPARABLE SOCKET AN INDICATION OF WHETHER OR NOT A SEPARABLE SOCKET IS PROVIDED. SELECT REPLY CODE 10AB22 BLQJD /D/ 07GLASS,PROTECTIVE PROTECTIVE GLASS AN INDICATION OF WHETHER OR NOT A PROTECTIVE GLASS IS PROVIDED. SELECT REPLY CODE 10AB22 BLQKD /D/ 18TYPE,CONNECTION,MOUNTING MOUNTING CONNECTION TYPE INDICATES THE TYPE OF MOUNTING CONNECTION PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AM39 BLQLG /D/ 04SIZE/D/,CONNECTION,MOUNTING MOUNTING CONNECTION SIZE/D/ DESIGNATES THE SIZE OF THE MOUNTING CONNECTION. FULL TEXT WRITE-IN 0 BLQMD /D/ 07FACE,PROTECTIVE,TRANSPARENT TRANSPARENT PROTECTIVE FACE AN INDICATION OF WHETHER OR NOT A TRANSPARENT PROTECTIVE FACE IS PROVIDED. SELECT REPLY CODE 10AB22 BLQND /D/ 07CHAMBER,EXPANSION EXPANSION CHAMBER AN INDICATION OF WHETHER OR NOT AN EXPANSION CHAMBER IS PROVIDED. SELECT REPLY CODE 10AB22 BLQPD /D/ 07FEATURE,OFFSET FROM STEM,BULB BULB OFFSET FROM STEM FEATURE AN INDICATION OF WHETHER OR NOT A BULB OFFSET FROM STEM FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BLQQD /D/ 09MATERIAL,POINT,PIERCING PIERCING POINT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PIERCING POINT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BLQRJ 10PRESSURE,RATED,GAGE GAGE RATED PRESSURE THE PRESSURE AT WHICH THE GAGE IS RATED. 1D AND 1B MODE REPLY12AG20 BLQSD /D/ 07SHIELD,MICA MICA SHIELD AN INDICATION OF WHETHER OR NOT A MICA SHIELD IS PROVIDED. SELECT REPLY CODE 10AB22 BLQTJ T10RANGE,TEST TEST RANGE THE MINIMUM TO MAXIMUM LIMITS AT WHICH EXAMINATION OF AN ITEM IS PERFORMED. 1D AND 1F MODE REPLY12AG20 BLQWD 11METHOD,CALIBRATION,SCALE SCALE CALIBRATION METHOD THE MEANS USED TO CALIBRATE THE ITEM. SELECT REPLY CODE 10AL39 BLQXD /D/ 07SCREW,LEVELING LEVELING SCREW AN INDICATION OF WHETHER OR NOT A LEVELING SCREW(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BLQYD /D/ 07SYSTEM,SUPPLY,WATER WATER SUPPLY SYSTEM AN INDICATION OF WHETHER OR NOT A WATER SUPPLY SYSTEM IS INCLUDED. SELECT REPLY CODE 10AA49 BLQZJ 04LENGTH,TURNTABLE TURNTABLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A TURNTABLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BLRBJ 04WIDTH,TURNTABLE TURNTABLE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A TURNTABLE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BLRCJ /D/ 10RESISTANCE,INPUT,DC DC INPUT RESISTANCE THE OPPOSITION TO THE FLOW OF INPUT DIRECT CURRENT OFFERED BY THE ITEM. 2D AND 1B MODE REPLY22AE751AC20 BLRDD 18TYPE,DRIER DRIER TYPE INDICATES THE TYPE OF DRIER PROVIDED. SELECT REPLY CODE 10AN01 BLRFJ 04WIDTH,MAXIMUM,PLATE PLATE MAXIMUM WIDTH THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A PLATE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BLRGJ 04LENGTH,MAXIMUM,PLATE PLATE MAXIMUM LENGTH THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF A PLATE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BLRHJ 04HEIGHT,MAXIMUM,PILE PILE MAXIMUM HEIGHT THE MAXIMUM MEASUREMENT FROM THE BOTTOM TO THE TOP OF A PILE,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BLRJD 18TYPE,GAGE,BACK BACK GAGE TYPE INDICATES THE TYPE OF BACK GAGE PROVIDED. SELECT REPLY CODE 10AJ89 BLRKD 11METHOD,ACTUATION,CUTTING BLADE CUTTING BLADE ACTUATION METHOD THE MEANS BY WHICH THE CUTTING BLADE IS ACTUATED. SELECT REPLY CODE 10AC58 BLRLD /D/ 07FEATURE,PROCESSING,AUTOMATIC CONTINUOUS AUTOMATIC CONTINUOUS PROCESSING FEATURE AN INDICATION OF WHETHER OR NOT AN AUTOMATIC CONTINUOUS PROCESSING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BLRMJ 04WIDTH,MAXIMUM,ORIGINAL COPY ORIGINAL COPY MAXIMUM WIDTH THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ORIGINAL COPY,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BLRNJ 04LENGTH,MAXIMUM,ORIGINAL COPY ORIGINAL COPY MAXIMUM LENGTH THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF THE ORIGINAL COPY,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BLRPJ 04WIDTH,MAXIMUM,PRINT PRINT MAXIMUM WIDTH THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PRINT,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BLRQJ 04LENGTH,MAXIMUM,PRINT PRINT MAXIMUM LENGTH THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF THE PRINT,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BLRRJ 04WIDTH,EXPOSURE,COPYHOLDER COPYHOLDER EXPOSURE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE COPYHOLDER EXPOSURE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BLRSD 18TYPE,COPYHOLDER COPYHOLDER TYPE INDICATES THE TYPE OF COPYHOLDER PROVIDED. SELECT REPLY CODE 10AK54 BLRTJ 04LENGTH,EXPOSURE,COPYHOLDER COPYHOLDER EXPOSURE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE COPYHOLDER EXPOSURE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BLRWD 18TYPE,CONTROL,VACUUM VACUUM CONTROL TYPE INDICATES THE TYPE OF VACUUM CONTROL(S) PROVIDED. SELECT REPLY CODE 10AL37 BLRXD /D/ 11METHOD,ATTACHMENT,CIRCUIT CIRCUIT ATTACHMENT METHOD THE MEANS PROVIDED FOR ATTACHING AN ITEM TO A CIRCUIT. SELECT REPLY CODE 10AB47 BLRYJ /D/T10ACCURACY RATING PER INDICATOR IN PERCENT ACCURACY RATING PER INDICATOR IN PERCENT THE AMOUNT OF DEVIATION FROM THE EXACT READING PER INDICATOR,EXPRESSED IN PERCENT. 2D AND 1F MODE REPLY22AD213AJ91 BLRZD /D/ 11METHOD,SUSPENSION SUSPENSION METHOD THE MEANS EMPLOYED TO SUSPEND THE ITEM. SELECT REPLY CODE 10AH72 BLSBD 11METHOD,SELECTION,SCALE SCALE SELECTION METHOD THE MEANS PROVIDED FOR SELECTING A SCALE. SELECT REPLY CODE 10AL28 BLSCJ /D/ 10CAPACITANCE,SHUNTING SHUNTING CAPACITANCE THE VALUE OF CAPACITANCE SHUNTING THE ITEM. 2D AND 1B MODE REPLY22AE751AC20 BLSDG 19HARDWARE AND QUANTITY,MOUNTING MOUNTING HARDWARE AND QUANTITY THE MOUNTING HARDWARE FURNISHED AND THE NUMBER OF EACH. FULL TEXT WRITE-IN 0 BLSFD /D/ 07COMBINATION,FIXED LIGHT/MOVABLE SASH FIXED LIGHT/MOVABLE SASH COMBINATION AN INDICATION OF WHETHER OR NOT A COMBINATION OF FIXED LIGHT/S/ AND MOVABLE SASH IS PROVIDED. SELECT REPLY CODE 10AB22 BLSGD /D/ 07FEATURE,DESIGN,MARINE SERVICE MARINE SERVICE DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A MARINE SERVICE DESIGN FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BLSHD /D/ 07PARTS,MAINTENANCE MAINTENANCE PARTS AN INDICATION OF WHETHER OR NOT MAINTENANCE PARTS ARE PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AB22 BLSJJ 12QUANTITY,PERFORATION PERFORATION QUANTITY THE NUMBER OF PERFORATION(S) PER SPECIFIC MEASUREMENT SCALE. 2D AND 1B MODE REPLY22AG551AC20 BLSKD /D/ 07BOILER,PACKAGED PACKAGED BOILER AN INDICATION OF WHETHER OR NOT A PACKAGED BOILER IS PROVIDED. SELECT REPLY CODE 10AB22 BLSLD /D/ 07SUPERHEATER SUPERHEATER AN INDICATION OF WHETHER OR NOT A SUPERHEATER IS PROVIDED. SELECT REPLY CODE 10AB22 BLSMD /D/ 07FEATURE,FIRED,SEPARATELY SEPARATELY FIRED FEATURE AN INDICATION OF WHETHER OR NOT A SEPARATELY FIRED FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BLSND 19PROTECTION FROM HEAT SOURCE,WORK WORK PROTECTION FROM HEAT SOURCE THE EXTENT OF WORK PROTECTION PROVIDED FROM THE HEAT SOURCE. SELECT REPLY CODE 10AD33 BLSPJ 10SIZE,CELL CELL SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE CELL. 2D AND 1B MODE REPLY21AA051AC20 BLSQJ T10RANGE,TEMP,NORMAL OPERATING NORMAL OPERATING TEMP RANGE THE MINIMUM AND MAXIMUM LIMITS OF TEMPERATURE AT WHICH THE ITEM IS NORMALLY OPERATED. 1D AND 1F MODE REPLY11AB36 BLSRD /D/ 07CONSTRUCTION,WALL,DOUBLE,CABINET CABINET DOUBLE WALL CONSTRUCTION AN INDICATION OF WHETHER OR NOT A DOUBLE WALL CONSTRUCTED CABINET IS PROVIDED. IF PROVIDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AB22 BLSSB 10AREA IN PERCENT,OPEN OPEN AREA IN PERCENT THE OPEN AREA OF THE ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 BLSTD /D/ 07CABINET,INSULATED INSULATED CABINET AN INDICATION OF WHETHER OR NOT AN INSULATED CABINET IS PROVIDED. IF PROVIDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AB22 BLSWG /D/ 04THICKNESS,METAL METAL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE METAL FROM WHICH THE ITEM IS FABRICATED,IN DISTINCTION FROM LENGTH OR WIDTH. PLEASE USE MRC BNPQ IN PLACE OF THIS CANCELED MRC. FULL TEXT WRITE-IN 0 BLSXD /D/ 07VENT,EXHAUST,CABINET CABINET EXHAUST VENT AN INDICATION OF WHETHER OR NOT A CABINET EXHAUST VENT IS PROVIDED. IF PROVIDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AB22 BLSYD /D/ 07OPENING,ADJUSTABLE ADJUSTABLE OPENING AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE OPENING IS PROVIDED. IF PROVIDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AB22 BLSZD /D/ 07INTAKE,AIR,FRESH,CABINET CABINET FRESH AIR INTAKE AN INDICATION OF WHETHER OR NOT A CABINET FRESH AIR INTAKE IS PROVIDED. IF PROVIDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AB22 BLTBD /D/ 07OPENING,ADJUSTABLE,FRESH AIR INTAKE FRESH AIR INTAKE ADJUSTABLE OPENING AN INDICATION OF WHETHER OR NOT A FRESH AIR INTAKE ADJUSTABLE OPENING IS PROVIDED. IF PROVIDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AB22 BLTCD 18TYPE,THERMOMETER THERMOMETER TYPE INDICATES THE TYPE OF THERMOMETER PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AC58 BLTDA /D/ 03DESIGNATOR FOR WHICH DESIGNED,SIZE,CRUCIBLE CRUCIBLE SIZE DESIGNATOR FOR WHICH DESIGNED A DESIGNATION INDICATING THE SIZE BY WHICH THE CRUCIBLE,FOR WHICH THE ITEM IS DESIGNED,IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1A MODE REPLY 0 BLTFJ 04SIZE,NOZZLE NOZZLE SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE NOZZLE. 1D AND 1B MODE REPLY11AA05 BLTGD 18TYPE,NOZZLE NOZZLE TYPE INDICATES THE TYPE OF NOZZLE PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AK95 BLTHJ /D/A12QUANTITY AND LOCATION,NOZZLE NOZZLE QUANTITY AND LOCATION THE NUMBER OF NOZZLE/S/ PROVIDED AND THE LOCATION. 1D AND 1A MODE REPLY13AJ91 BLTJG /D/ 04SIZE,OPENING,DOWNSPOUT OUTLET DOWNSPOUT OUTLET OPENING SIZE DESIGNATES THE SIZE OF THE DOWNSPOUT OUTLET OPENING. PLEASE USE MRC BXFY IN PLACE OF THIS CANCELED MRC. FULL TEXT WRITE-IN 0 BLTKG 04SPACING,NOZZLE NOZZLE SPACING THE SPACING BETWEEN THE NOZZLES. FULL TEXT WRITE-IN 0 BLTLD 18TYPE,END,CLOSED CLOSED END TYPE INDICATES THE TYPE OF CLOSED END PROVIDED ON THE ITEM. SELECT REPLY CODE 10AK16 BLTMJ 04DIAMETER,BILGE BILGE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BILGE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BLTNJ 04DIAMETER,BOTTOM BOTTOM DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOTTOM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BLTPD 02DESIGN,LIP,POURING POURING LIP DESIGN THE DESIGN OF THE POURING LIP PROVIDED. SELECT REPLY CODE 10AM13 BLTQD 18TYPE,LIP,POURING POURING LIP TYPE INDICATES THE TYPE OF POURING LIP PROVIDED. SELECT REPLY CODE 10AH97 BLTRD 18TYPE,PRESSURE,OPERATING OPERATING PRESSURE TYPE INDICATES THE TYPE OF OPERATING PRESSURE PROVIDED. SELECT REPLY CODE 10AC58 BLTSD 11METHOD,OPERATION,CONTROL VALVE CONTROL VALVE OPERATION METHOD THE MEANS USED TO OPERATE THE CONTROL VALVE. SELECT REPLY CODE 10AC58 BLTTD 05DIRECTION,ROTATION,CAM CAM ROTATION DIRECTION THE DIRECTION OF ROTATION FOR WHICH THE CAM IS DESIGNED. SELECT REPLY CODE 10AA38 BLTWB 10ROTATION IN DEG,CAM CAM ROTATION IN DEG THE CAM ROTATION,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BLTXA 12QUANTITY,SASH,CASEMENT CASEMENT SASH QUANTITY THE NUMBER OF CASEMENT SASH(ES) PROVIDED. 1A MODE REPLY 0 BLTYJ 04WIDTH FOR WHICH DESIGNED,OPENING OPENING WIDTH FOR WHICH DESIGNED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE OPENING FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BLTZJ 04HEIGHT FOR WHICH DESIGNED,OPENING OPENING HEIGHT FOR WHICH DESIGNED A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE OPENING FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BLWBD 18TYPE,SASH SASH TYPE INDICATES THE TYPE OF SASH FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AK54 BLWCD /D/ 05DIRECTION,SWING OUT SWING OUT DIRECTION AN INDICATION OF THE SWING OUT DIRECTION. SELECT REPLY CODE 10AJ91 BLWDJ 04DEPTH,CUTTING,MAXIMUM MAXIMUM CUTTING DEPTH THE MAXIMUM MEASUREMENT BETWEEN SPECIFIED POINTS OF THE CUTTING DEPTH,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 BLWFD 18TYPE,TINE TINE TYPE INDICATES THE TYPE OF TINE PROVIDED. SELECT REPLY CODE 10AK54 BLWGJ 10CAPACITY,CUBIC,BAG BAG CUBIC CAPACITY THE CUBIC CAPACITY OF THE BAG AS ESTABLISHED BY GOVERNMENTAL OR INDUSTRIAL SPECIFICATIONS AND/OR STANDARDS. 1D AND 1B MODE REPLY12AG67 BLWHJ A19PROVISION AND QUANTITY,ATTACHING ATTACHING PROVISION AND QUANTITY THE PROVISIONS FOR ATTACHING TO AN ITEM AND THE NUMBER OF EACH. 1D AND 1A MODE REPLY13AM39 BLWJD /D/ 07DOLLY,CONVERTER CONVERTER DOLLY AN INDICATION OF WHETHER OR NOT A CONVERTER DOLLY IS INCLUDED. SELECT REPLY CODE 10AA49 BLWKD /D/ 07SCARIFIER SCARIFIER AN INDICATION OF WHETHER OR NOT A SCARIFIER IS INCLUDED. SELECT REPLY CODE 10AA49 BLWLJ 10HORSEPOWER,RECOMMENDED RECOMMENDED HORSEPOWER THE HORSEPOWER RECOMMENDED TO START AND OPERATE THE ITEM. 1D AND 1B MODE REPLY11AC20 BLWMA 12QUANTITY,SHANK SHANK QUANTITY THE NUMBER OF SHANKS PROVIDED. 1A MODE REPLY 0 BLWND /D/ 18TYPE,SHANK SHANK TYPE INDICATES THE TYPE OF SHANK PROVIDED. SELECT REPLY CODE 10AM11 BLWPD 11METHOD,OPERATION,SHANK SHANK OPERATION METHOD THE MEANS BY WHICH THE SHANK IS OPERATED. SELECT REPLY CODE 10AC58 BLWQJ 04DEPTH,SHANK PENETRATION,MAXIMUM MAXIMUM SHANK PENETRATION DEPTH THE MAXIMUM MEASUREMENT BETWEEN SPECIFIED POINTS OF THE PENETRATION DEPTH FOR WHICH THE SHANK IS DESIGNED,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 BLWRD 19COMPONENTS,REPLACEABLE,SHANK SHANK REPLACEABLE COMPONENTS THE REPLACEABLE COMPONENTS OF THE SHANK. SELECT REPLY CODE 10AE15 BLWSJ 04WIDTH,CUTTING,MAXIMUM MAXIMUM CUTTING WIDTH A MEASUREMENT OF THE MAXIMUM CUTTING WIDTH OF THE ITEM. 1D AND 1B MODE REPLY11AA05 BLWTD 19CHARACTERISTIC,ARRANGEMENT,WHEEL WHEEL ARRANGEMENT CHARACTERISTIC THE ARRANGEMENT CHARACTERISTIC/S/ OF THE WHEELS. SELECT REPLY CODE 10AH86 BLWWD 11METHOD,HEATING,MATERIAL MATERIAL HEATING METHOD THE MEANS BY WHICH THE MATERIAL IS HEATED. SELECT REPLY CODE 10AM63 BLWXB 10CAPACITY IN BTU PER HOUR,OUTPUT OUTPUT CAPACITY IN BTU PER HOUR THE OUTPUT CAPACITY OF THE ITEM,EXPRESSED IN BRITISH THERMAL UNITS PER HOUR. 1B MODE REPLY 0 BLWYB 10CAPACITY,HORSEPOWER,STEAM GENERATOR STEAM GENERATOR HORSEPOWER CAPACITY THE CAPACITY OF THE STEAM GENERATOR,EXPRESSED IN HORSEPOWER. 1B MODE REPLY 0 BLWZD /D/ 18TYPE,BURNER,FUEL FUEL BURNER TYPE INDICATES THE TYPE OF FUEL BURNER PROVIDED. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AB75 BLXBB /D/ 10CAPACITY IN KVA,GENERATOR GENERATOR CAPACITY IN KVA THE OUTPUT CAPACITY OF THE GENERATOR,EXPRESSED IN KILOVOLT-AMPERE. 1B MODE REPLY 0 BLXCJ 10OUTPUT,STEAM,MINIMUM MINIMUM STEAM OUTPUT THE MINIMUM STEAM OUTPUT OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BLXDA 19CAPACITY,HEATING,TANK CAR TANK CAR HEATING CAPACITY THE NUMBER OF TANK CAR(S) THE ITEM IS RATED TO HEAT. 1A MODE REPLY 0 BLXFD /D/ 07FEATURE,DESIGN,RESILIENT JOINT SEALING COMPOUND RESILIENT JOINT SEALING COMPOUND DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A RESILIENT JOINT SEALING COMPOUND DESIGN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BLXGA 12QUANTITY,BURNER BURNER QUANTITY THE NUMBER OF BURNERS INCLUDED ON THE ITEM. 1A MODE REPLY 0 BLXHD /D/ 07TANK,INSULATED INSULATED TANK AN INDICATION OF WHETHER OR NOT AN INSULATED TANK IS INCLUDED. SELECT REPLY CODE 10AA49 BLXJJ 04HEIGHT,LOADING LOADING HEIGHT THE HEIGHT AT WHICH THE ITEM IS DESIGNED TO BE LOADED. 2D AND 1B MODE REPLY21AA051AC20 BLXKA 12QUANTITY,LID,LOADING LOADING LID QUANTITY THE NUMBER OF LOADING LID(S) PROVIDED ON THE ITEM. 1A MODE REPLY 0 BLXLD 18TYPE,LID,LOADING LOADING LID TYPE INDICATES THE TYPE OF LOADING LID PROVIDED. SELECT REPLY CODE 10AK54 BLXMD /D/ 07AGITATOR,BITUMEN BITUMEN AGITATOR AN INDICATION OF WHETHER OR NOT A BITUMEN AGITATOR IS INCLUDED. SELECT REPLY CODE 10AA49 BLXND 11METHOD,DISCHARGING,BITUMEN BITUMEN DISCHARGING METHOD THE MEANS UTILIZED FOR DISCHARGING BITUMEN FROM THE ITEM. SELECT REPLY CODE 10AL88 BLXPJ 10CAPACITY,DISCHARGE DISCHARGE CAPACITY THE DISCHARGE CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BLXQD 19SOURCE,POWER,BITUMEN DISCHARGE BITUMEN DISCHARGE POWER SOURCE THE SOURCE OF POWER USED FOR BITUMEN DISCHARGING. SELECT REPLY CODE 10AG27 BLXRD /D/ 07FEATURE,HEATING,PAVING HAND TOOL PAVING HAND TOOL HEATING FEATURE AN INDICATION OF WHETHER OR NOT A PAVING HAND TOOL HEATING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BLXSG 10HORSEPOWER AT SPECIFIED RPM,BRAKE,ENGINE MAXIMUM ENGINE MAXIMUM BRAKE HORSEPOWER AT SPECIFIED RPM THE MAXIMUM BRAKE HORSEPOWER OF THE ENGINE,AT SPECIFIED REVOLUTIONS PER MINUTE. FULL TEXT WRITE-IN 0 BLXTJ /D/ 04WIDTH,HOOD,HEATING HEATING HOOD WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A HEATING HOOD,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BLXWJ /D/ 04LENGTH,HOOD,HEATING HEATING HOOD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A HEATING HOOD,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BLXXD /D/ 19MEDIA FOR WHICH BURNER IS DESIGNED MEDIA FOR WHICH BURNER IS DESIGNED THE TYPE OF SERVICE WITH WHICH THE BURNER IS DESIGNED TO BE USED. SELECT REPLY CODE 10AB75 BLXYA /D/ 12QUANTITY,BLADE,PLANING PLANING BLADE QUANTITY THE NUMBER OF PLANING BLADES PROVIDED. 1A MODE REPLY 0 BLXZJ /D/ 04WIDTH,CUT,PLANING PLANING CUT WIDTH A MEASUREMENT OF THE PLANING CUT WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BLYBJ /D/ 04DEPTH,CUT,PLANING,MAXIMUM MAXIMUM PLANING CUT DEPTH THE MAXIMUM MEASUREMENT BETWEEN SPECIFIED POINTS OF THE PLANING CUT,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 BLYCB 10PERCENTAGE,SILICA,ACID LEACHED GLASS ACID LEACHED GLASS SILICA PERCENTAGE THE SILICA CONTENT OF ACID LEACHED GLASS,EXPRESSED IN PERCENT. 1B MODE REPLY 0 BLYDA 12QUANTITY,SASH SASH QUANTITY THE NUMBER OF SASHES PROVIDED. 1A MODE REPLY 0 BLYFD 08LOCATION,LIGHT,FIXED FIXED LIGHT LOCATION INDICATES THE LOCATION OF THE FIXED LIGHT. SELECT REPLY CODE 10AJ91 BLYGD /D/ 03DESIGNATOR,POROSITY,MATERIAL MATERIAL POROSITY DESIGNATOR A DESIGNATION INDICATING THE GENERAL POROSITY OF THE MATERIAL. SELECT REPLY CODE 10AF67 BLYHD 08LOCATION,MATERIAL,POROUS POROUS MATERIAL LOCATION INDICATES THAT PORTION OF AN ITEM ON WHICH THE POROUS MATERIAL IS LOCATED. SELECT REPLY CODE 10AJ91 BLYJG 19ARRANGEMENT,LIGHT LIGHT ARRANGEMENT THE MANNER IN WHICH THE LIGHTS ARE ARRANGED. FULL TEXT WRITE-IN 0 BLYKG /D/ 19DIMENSIONS,LIGHT LIGHT DIMENSIONS THE MEASUREMENTS WHICH ARE CHARACTERISTIC OF THE LIGHT AND ESTABLISH ITS PHYSICAL LIMITS. FULL TEXT WRITE-IN 0 BLYLG 04SIZE,TOP TOP SIZE DESIGNATES THE SIZE OF THE TOP. FULL TEXT WRITE-IN 0 BLYMD 07FEATURE,GLAZE GLAZE FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM IS GLAZED. SELECT REPLY CODE 10AK39 BLYND 18TYPE,GLAZE GLAZE TYPE INDICATES THE TYPE OF GLAZE PROVIDED. SELECT REPLY CODE 10AK95 BLYPD /D/ 08LOCATION,GLAZE GLAZE LOCATION INDICATES THE LOCATION OF THE GLAZE ON THE ITEM. SELECT REPLY CODE 10AJ91 BLYQA /D/ 19UNDERWRITERS LABORATORIES RATING UNDERWRITERS LABORATORIES RATING A LABORATORY DESIGNATOR RATING FOR THE ITEM. 1A MODE REPLY 0 BLYRD /D/ 07STOPPER STOPPER AN INDICATION OF WHETHER OR NOT A STOPPER IS INCLUDED. SELECT REPLY CODE 10AA49 BLYSD /D/ 07FEATURE,DOOR,DOUBLE DOUBLE DOOR FEATURE AN INDICATION OF WHETHER OR NOT A DOUBLE DOOR FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BLYTD 02DESIGN,EDGES,MEETING MEETING EDGES DESIGN THE DESIGN OF THE MEETING EDGES. SELECT REPLY CODE 10AJ57 BLYWD 05DIRECTION,SWING SWING DIRECTION THE DIRECTION IN WHICH THE ITEM SWINGS. SELECT REPLY CODE 10AJ91 BLYXG /D/ 10INTERVAL,SCALE SCALE INTERVAL THE VALUE OF THE INTERVALS ON A SCALE. FULL TEXT WRITE-IN 0 BLYYH 11METHOD AND LOCATION,MOUNTING MOUNTING METHOD AND LOCATION THE MEANS OF ATTACHING THE ITEM AND ITS LOCATION. 2D MODE REPLY 23AM393AJ91 BLYZJ 04WIDTH,STILE STILE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE STILE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BLZBD 08LOCATION,RAIL RAIL LOCATION INDICATES THE LOCATION OF THE RAIL(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 BLZCJ 04WIDTH,RAIL RAIL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE RAIL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BLZDG /D/ 08LOCATION,MARKING,SCALE INTERVAL SCALE INTERVAL MARKING LOCATION AN INDICATION OF WHERE THE INTERVAL MARKING/S/ APPEARS ON THE SCALE. FULL TEXT WRITE-IN 0 BLZFD 08LOCATION,PANEL PANEL LOCATION INDICATES THE LOCATION OF THE PANEL(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 BLZGD 19PURPOSE,GRADUATION,SCALE SCALE GRADUATION PURPOSE AN INDICATION OF THE PURPOSE OF THE SCALE GRADUATION(S). SELECT REPLY CODE 10AK54 BLZHD /D/ 07ROD,FITTED FITTED ROD AN INDICATION OF WHETHER OR NOT A FITTED ROD IS INCLUDED. SELECT REPLY CODE 10AA49 BLZJA /D/ 03DESIGNATION,SIZE,STANDARD TAPER,MOUTH EXTERNAL MOUTH EXTERNAL STANDARD TAPER SIZE DESIGNATION A NUMERIC SIZE DESIGNATION BY WHICH THE EXTERNAL STANDARD TAPER OF THE MOUTH IS IDENTIFIED. 1A MODE REPLY 0 BLZKA /D/ 03DESIGNATION,SIZE,STANDARD TAPER,MOUTH INTERNAL MOUTH INTERNAL STANDARD TAPER SIZE DESIGNATION A NUMERIC SIZE DESIGNATION BY WHICH THE INTERNAL STANDARD TAPER OF THE MOUTH IS IDENTIFIED. 1A MODE REPLY 0 BLZLJ 04WIDTH,PANEL PANEL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PANEL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BLZMJ 04HEIGHT,PANEL PANEL HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE PANEL,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BLZNG 04SIZE,CROSS-SECTIONAL,WIRE WIRE CROSS-SECTIONAL SIZE DESIGNATES THE CROSS-SECTIONAL SIZE OF THE WIRE. FULL TEXT WRITE-IN 0 BLZPD 08LOCATION,SASH SASH LOCATION INDICATES THE LOCATION OF THE SASH ON THE ITEM. SELECT REPLY CODE 10AJ91 BLZQA /D/ 19NUMBER,STOPPER,RUBBER RUBBER STOPPER NUMBER THE NUMBER BY WHICH THE SIZE OF THE RUBBER STOPPER IS IDENTIFIED. 1A MODE REPLY 0 BLZRD /D/ 07TUBE,SIDE SIDE TUBE AN INDICATION OF WHETHER OR NOT A SIDE TUBE IS INCLUDED. SELECT REPLY CODE 10AA49 BLZSD /D/ 07STOPCOCK,TUBE,SIDE SIDE TUBE STOPCOCK AN INDICATION OF WHETHER OR NOT A STOPCOCK IS INCLUDED ON THE SIDE TUBE. SELECT REPLY CODE 10AA49 BLZTJ 04WIDTH,LIGHT LIGHT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE LIGHT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BLZWA 12QUANTITY,CAVITY CAVITY QUANTITY THE NUMBER OF CAVITY(IES) ON THE ITEM. 1A MODE REPLY 0 BLZXJ 04HEIGHT,LIGHT LIGHT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE LIGHT,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BLZYJ /D/ 04LENGTH,OVERALL,CAVITY CAVITY OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CAVITY. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 2D AND 1B MODE REPLY21AA051AC20 BLZZJ 04DIAMETER,OVERALL,CAVITY CAVITY OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE CIRCULAR CROSS-SECTIONAL PLANE OF THE CAVITY. 2D AND 1B MODE REPLY21AA051AC20 BMBBJ 04DEPTH,OVERALL,CAVITY CAVITY OVERALL DEPTH AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF A CAVITY,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BMBCG 08LOCATION,MORTISE MORTISE LOCATION INDICATES THE LOCATION OF THE MORTISE. FULL TEXT WRITE-IN 0 BMBDJ 04LENGTH,MORTISE MORTISE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE MORTISE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BMBFJ 04WIDTH,MORTISE MORTISE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MORTISE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BMBGD 14SHAPE,BOTTOM,CAVITY CAVITY BOTTOM SHAPE THE PHYSICAL CONFIGURATION OF THE CAVITY BOTTOM. SELECT REPLY CODE 10AD07 BMBHD /D/ 07FEATURE,TAPPED FOR HARDWARE,MORTISE MORTISE TAPPED FOR HARDWARE FEATURE AN INDICATION OF WHETHER OR NOT A TAPPED MORTISE FOR HARDWARE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BMBJD /D/ 07FEATURE,USAGE,EMBRYOLOGICAL EMBRYOLOGICAL USAGE FEATURE AN INDICATION OF WHETHER OR NOT AN EMBRYOLOGICAL USAGE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BMBKJ 04DIAMETER,WELL WELL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WELL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BMBLD /D/ 07STRAINER STRAINER AN INDICATION OF WHETHER OR NOT A STRAINER IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BMBMJ 04DEPTH,WELL WELL DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON A WELL,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BMBND /D/ 07HOLE,CENTER CENTER HOLE AN INDICATION OF WHETHER OR NOT A CENTER HOLE IS INCLUDED. SELECT REPLY CODE 10AA49 BMBPD /D/ 07HANDLE,LIP LIP HANDLE AN INDICATION OF WHETHER OR NOT A LIP HANDLE IS INCLUDED. SELECT REPLY CODE 10AA49 BMBQD /D/ 07FEATURE,RIBBED,CONVEX SIDE CONVEX SIDE RIBBED FEATURE AN INDICATION OF WHETHER OR NOT A RIBBED FEATURE IS PROVIDED ON THE CONVEX SIDE. SELECT REPLY CODE 10AB22 BMBRD 02DESIGN,BLADE BLADE DESIGN THE DESIGN OF THE BLADE. SELECT REPLY CODE 10AL25 BMBSJ /D/ 04HEIGHT,FOOT FOOT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A FOOT,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BMBTD 07ADJUSTABILITY,ANGLE ANGLE ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE ANGLE IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BMBWD /D/ 07OUTLET,SIDE SIDE OUTLET AN INDICATION OF WHETHER OR NOT A SIDE OUTLET IS INCLUDED. SELECT REPLY CODE 10AA49 BMBXJ 04DEPTH,BAR BAR DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON A BAR,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BMBYJ 04THICKNESS,BAR BAR THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A BAR,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BMBZJ 04LENGTH,PANEL PANEL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE PANEL,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BMCBD 05DIRECTION,BAR,MAIN MAIN BAR DIRECTION INDICATES THE DIRECTION THE MAIN BAR RUNS. SELECT REPLY CODE 10AK54 BMCCJ 04DISTANCE BETWEEN PARALLEL BARS DISTANCE BETWEEN PARALLEL BARS THE DISTANCE BETWEEN THE PARALLEL BARS. 2D AND 1B MODE REPLY21AA051AC20 BMCDD 14SHAPE,CROSSBAR CROSSBAR SHAPE THE PHYSICAL CONFIGURATION OF THE CROSSBAR. SELECT REPLY CODE 10AD07 BMCFJ 04LENGTH,SURFACE,CLAMPING CLAMPING SURFACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CLAMPING SURFACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BMCGD 11METHOD,ATTACHING,CROSSBAR CROSSBAR ATTACHING METHOD THE MEANS USED TO ATTACH THE CROSSBAR/S/ TO THE MAIN BAR/S/. SELECT REPLY CODE 10AA62 BMCHD /D/ 07FASTENERS,GRATE GRATE FASTENERS AN INDICATION OF WHETHER OR NOT GRATE FASTENERS ARE PROVIDED. SELECT REPLY CODE 10AB22 BMCJD 14SHAPE,SEAM SEAM SHAPE THE PHYSICAL CONFIGURATION OF THE SEAM. SELECT REPLY CODE 10AD07 BMCKD /D/ 07END,CRIMPED CRIMPED END AN INDICATION OF WHETHER OR NOT A CRIMPED END IS INCLUDED. SELECT REPLY CODE 10AA49 BMCLD /D/ 07THREADS ON ENDS,RIGHT-HAND RIGHT-HAND THREADS ON ENDS AN INDICATION OF WHETHER OR NOT RIGHT-HAND THREADS ARE PROVIDED ON ENDS. SELECT REPLY CODE 10AB22 BMCMD /D/ 07THREAD ON AXIS,LEFT-HAND,ONE ONE LEFT-HAND THREAD ON AXIS AN INDICATION OF WHETHER OR NOT ONE LEFT-HAND THREAD IS PROVIDED ON AXIS. SELECT REPLY CODE 10AB22 BMCNG /D/ 04SIZE,PIPE,NOMINAL,RUN RUN NOMINAL PIPE SIZE THE INDUSTRIAL DESIGNATOR OR TERM FOR THE SIZE OF THE NOMINAL PIPE RUN. FULL TEXT WRITE-IN 0 BMCPH 13THREAD DIRECTION AND LOCATION,PIPE,RUN RUN PIPE THREAD DIRECTION AND LOCATION THE DIRECTION AND LOCATION OF THE THREAD WHEN VIEWED AXIALLY. 2D MODE REPLY 21AA383AJ91 BMCQG /D/ 04SIZE,PIPE,NOMINAL,BRANCH BRANCH NOMINAL PIPE SIZE THE INDUSTRIAL DESIGNATOR OR TERM FOR THE SIZE OF THE NOMINAL PIPE BRANCH. FULL TEXT WRITE-IN 0 BMCRD 13THREAD DIRECTION,PIPE,BRANCH BRANCH PIPE THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AJ91 BMCSJ 04SIZE,PIPE,NOMINAL,SIDE OUTLET SIDE OUTLET NOMINAL PIPE SIZE THE INDUSTRIAL DESIGNATOR OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE SIDE OUTLET PIPE. 1D AND 1B MODE REPLY11AA05 BMCTD 13THREAD DIRECTION,PIPE,SIDE OUTLET SIDE OUTLET PIPE THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AJ91 BMCWJ A10STRENGTH,YIELD,MINIMUM MINIMUM YIELD STRENGTH THE STRESS AT WHICH A MATERIAL EXHIBITS A SPECIFIED LIMITING DEVIATION FROM THE PROPORTIONALITY OF STRESS TO STRAIN. 1D AND 1A MODE REPLY11AB18 BMCXD 14SHAPE,CROSS-SECTIONAL,SINGLE WIRE SINGLE WIRE CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE SINGLE WIRE WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 BMCYG /D/ 19DIMENSION,CROSS-SECTIONAL,WIRE WIRE CROSS-SECTIONAL DIMENSION A MEASUREMENT OF THE PHYSICAL LIMITS OF THE ITEM WHEN VIEWED IN CROSS SECTION. FULL TEXT WRITE-IN 0 BMCZD /D/ 07WIRE,TWO-STRAND TWO-STRAND WIRE AN INDICATION OF WHETHER OR NOT TWO-STRAND WIRE IS INCLUDED. SELECT REPLY CODE 10AA49 BMDBD 14SHAPE,CROSS-SECTIONAL,BARB BARB CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE BARB WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 BMDCA 12QUANTITY,VEE VEE QUANTITY THE NUMBER OF VEE(S) PROVIDED ON THE ITEM. 1A MODE REPLY 0 BMDDD 08LOCATION,VEE VEE LOCATION INDICATES THE LOCATION OF THE VEE(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 BMDFJ /D/A08LOCATION AND QUANTITY,GROOVE,MILLED MILLED GROOVE LOCATION AND QUANTITY INDICATES THE MILLED GROOVE LOCATION AND THE NUMBER PROVIDED. 1D AND 1A MODE REPLY13AJ91 BMDGJ 04DIAMETER ACCOMMODATED,MATERIAL,MAXIMUM MAXIMUM MATERIAL DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE MATERIAL,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BMDHD 14SHAPE,HOLE,INTERNAL GRIP INTERNAL GRIP HOLE SHAPE THE PHYSICAL CONFIGURATION OF THE INTERNAL GRIPPING HOLE. SELECT REPLY CODE 10AD07 BMDJJ A04SIZE,TAPER,BODY BODY TAPER SIZE DESIGNATES THE TAPER SIZE OF THE BODY. 1D AND 1A MODE REPLY12AH09 BMDKJ 10SIZE ACCOMMODATED,MATERIAL MATERIAL SIZE ACCOMMODATED DESIGNATES THE SIZE OF MATERIAL THAT THE ITEM WILL ACCOMMODATE. 2D AND 1B MODE REPLY21AA051AC20 BMDLJ 04DIAMETER,END,UPPER UPPER END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE UPPER END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BMDMJ 04LENGTH,END,LOWER LOWER END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BMDNJ 04LENGTH,END,UPPER UPPER END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BMDPJ 04LENGTH,END,LOWER,EXPANDING PILOT EXPANDING PILOT LOWER END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BMDQJ 04LENGTH,END,UPPER,EXPANDING PILOT EXPANDING PILOT UPPER END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BMDRJ A04SIZE,TAPER,OUTSIDE OUTSIDE TAPER SIZE DESIGNATES THE OUTSIDE TAPER SIZE. 1D AND 1A MODE REPLY12AH09 BMDSJ A04SIZE,TAPER,INSIDE INSIDE TAPER SIZE DESIGNATES THE INSIDE TAPER SIZE. 1D AND 1A MODE REPLY12AH09 BMDTD 18TYPE FOR WHICH DESIGNED,SHANK SHANK TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF SHANK FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AH09 BMDWA 12QUANTITY,OPENING,CUTTER CUTTER OPENING QUANTITY THE NUMBER OF CUTTER OPENING(S) PROVIDED. 1A MODE REPLY 0 BMDXD /D/ 08LOCATION,OPENING,CUTTER CUTTER OPENING LOCATION INDICATES THE LOCATION OF THE CUTTER OPENING(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 BMDYB 04ANGLE IN DEG,OPENING,CUTTER CUTTER OPENING ANGLE IN DEG THE ANGLE BETWEEN THE AXIS OF THE CUTTER OPENING AND THE AXIS OF THE ITEM,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BMDZD 11METHOD,LOCKING,CUTTER CUTTER LOCKING METHOD THE MEANS USED FOR LOCKING THE CUTTER. SELECT REPLY CODE 10AE44 BMFBD /D/ 07FEATURE,EXPANDING EXPANDING FEATURE AN INDICATION OF WHETHER OR NOT AN EXPANDING FEATURE IS INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AA49 BMFCD 14SHAPE ACCOMMODATED,BIT,CUTTER CUTTER BIT SHAPE ACCOMMODATED THE PHYSICAL CONFIGURATION OF THE CUTTER BIT THAT THE ITEM WILL ACCOMMODATE. SELECT REPLY CODE 10AD07 BMFDJ /D/T04DIAMETER RANGE,CUTTER,EXPANDING EXPANDING CUTTER DIAMETER RANGE THE MINIMUM TO MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE EXPANDING CUTTER,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1F MODE REPLY11AA05 BMFFD 19PURPOSE FOR WHICH GROUND PURPOSE FOR WHICH GROUND THE MACHINING OPERATION OR APPLICATION FOR WHICH THE CUTTER IS GROUND. SELECT REPLY CODE 10AK54 BMFGB 04ANGLE TO HORIZONTAL BAR AXIS IN DEG,END,CUTTING CUTTING END ANGLE TO HORIZONTAL BAR AXIS IN DEG THE ANGLE BETWEEN THE CUTTING END AND THE HORIZONTAL AXIS OF THE BAR,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BMFHD /D/ 07BUSHING BUSHING AN INDICATION OF WHETHER OR NOT A BUSHING IS INCLUDED. SELECT REPLY CODE 10AA49 BMFJD 14SHAPE,HOLE,CENTER CENTER HOLE SHAPE THE PHYSICAL CONFIGURATION OF THE CENTER HOLE. SELECT REPLY CODE 10AD07 BMFKA 03DESIGNATION,SIZE,TAPER TAPER SIZE DESIGNATION THE ALPHA AND/OR NUMERIC SIZE DESIGNATION BY WHICH THE TAPER IS IDENTIFIED. 1A MODE REPLY 0 BMFLJ 04WIDTH,SLOT,TEE TEE SLOT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TEE SLOT,FROM ONE EDGE TO THE OTHER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BMFMG 03DESIGNATION,SIZE,DIAMOND DIAMOND SIZE DESIGNATION THE INDUSTRIAL SIZE DESIGNATION FOR THE WEIGHT OF A DIAMOND. FULL TEXT WRITE-IN 0 BMFNA 12QUANTITY PER SET,FOLDER FOLDER QUANTITY PER SET THE NUMBER OF FOLDER(S) IN A SET. 1A MODE REPLY 0 BMFPG /D/ 04SIZE,SHEET,BASIC BASIC SHEET SIZE DESIGNATES THE BASIC SHEET SIZE. FULL TEXT WRITE-IN 0 BMFQD /D/ 07TOP,REINFORCED REINFORCED TOP AN INDICATION OF WHETHER OR NOT A REINFORCED TOP IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BMFRJ 04LENGTH,HORIZONTAL HORIZONTAL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION PARALLEL TO THE BASE OF AN ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BMFSJ 04LENGTH,VERTICAL VERTICAL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION PERPENDICULAR TO THE HORIZONTAL PLANE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BMFTD 18TYPE,BOTTOM BOTTOM TYPE INDICATES THE TYPE OF BOTTOM PROVIDED ON THE ITEM. SELECT REPLY CODE 10AJ17 BMFWD /D/ 07FASTENER,PAPER PAPER FASTENER AN INDICATION OF WHETHER OR NOT A PAPER FASTENER/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BMFXD /D/ 07INSERT,TRANSPARENT TRANSPARENT INSERT AN INDICATION OF WHETHER OR NOT A TRANSPARENT INSERT IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BMFYD /D/ 09MATERIAL,TAB TAB MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TAB IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BMFZD /D/ 07FEATURE,TAB,ANGULAR ANGULAR TAB FEATURE AN INDICATION OF WHETHER OR NOT AN ANGULAR TAB FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BMGBJ 10SPEED,MAXIMUM,FORWARD TRAVEL FORWARD TRAVEL MAXIMUM SPEED THE MAXIMUM FORWARD TRAVEL SPEED FOR WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY12AG67 BMGCJ /D/ 10SPEED,MAXIMUM,REVERSE TRAVEL REVERSE TRAVEL MAXIMUM SPEED THE MAXIMUM REVERSE TRAVEL SPEED FOR WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY12AG67 BMGDG /D/ 10RANGE,SPEED,PLANING PLANING SPEED RANGE THE MINIMUM TO MAXIMUM SPEED FOR WHICH THE PLANER IS DESIGNED. FULL TEXT WRITE-IN 0 BMGFJ 10CAPACITY,PUMP PUMP CAPACITY THE CAPACITY OF THE PUMP. 1D AND 1B MODE REPLY12AG67 BMGGG 19NAME,MANUFACTURER,TRUCK TRUCK MANUFACTURER NAME THE NAME OF THE MANUFACTURER OF THE TRUCK. FULL TEXT WRITE-IN 0 BMGHA 19NUMBER,IDENTIFYING,TRUCK MANUFACTURER TRUCK MANUFACTURER IDENTIFYING NUMBER THE NUMBER USED BY THE MANUFACTURER FOR IDENTIFYING THE TRUCK. 1A MODE REPLY 0 BMGJD /D/ 07UNIT,HEATING,TANK TANK HEATING UNIT AN INDICATION OF WHETHER OR NOT A TANK HEATING UNIT IS INCLUDED. SELECT REPLY CODE 10AA49 BMGKD 11METHOD,DISTRIBUTION DISTRIBUTION METHOD THE MEANS UTILIZED BY THE ITEM FOR DISTRIBUTION. SELECT REPLY CODE 10AF04 BMGLJ /D/A08LOCATION AND QUANTITY,HEAD,SPRINKLER SPRINKLER HEAD LOCATION AND QUANTITY INDICATES THE LOCATION AND NUMBER OF SPRINKLER HEAD(S) ON THE ITEM. 1D AND 1A MODE REPLY13AJ91 BMGMJ 04WIDTH,SPREAD SPREAD WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SPREAD,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BMGND 18TYPE,SPREADING SPREADING TYPE INDICATES THE SPREADING TYPE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BMGPD 11METHOD,SPREADING SPREADING METHOD THE MEANS USED BY THE ITEM FOR SPREADING. SELECT REPLY CODE 10AJ28 BMGQJ 04WIDTH,MAXIMUM,SPREAD PATH SPREAD PATH MAXIMUM WIDTH THE MAXIMUM WIDTH OF THE SPREAD PATH. 1D AND 1B MODE REPLY11AA05 BMGRD /D/ 07FEATURE,PATH,ADJUSTABLE SPREAD ADJUSTABLE SPREAD PATH FEATURE AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE SPREAD PATH FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BMGSD 18TYPE,OPERATION,HOPPER GATE HOPPER GATE OPERATION TYPE INDICATES THE TYPE OF HOPPER GATE UTILIZED TO OPERATE THE ITEM. SELECT REPLY CODE 10AE36 BMGTD 18TYPE,CONTROL,CAB,HOPPER GATE HOPPER GATE CAB CONTROL TYPE INDICATES THE MEANS UTILIZED TO CONTROL THE HOPPER GATE FROM THE CAB. SELECT REPLY CODE 10AL37 BMGWD /D/ 07AGITATOR,MATERIAL,HOPPER HOPPER MATERIAL AGITATOR AN INDICATION OF WHETHER OR NOT A HOPPER MATERIAL AGITATOR IS INCLUDED. SELECT REPLY CODE 10AA49 BMGXJ 10CAPACITY,STRUCK,HOPPER HOPPER STRUCK CAPACITY THE CAPACITY OF THE HOPPER STRUCK. 1D AND 1B MODE REPLY12AG67 BMGYJ A18TYPE AND QUANTITY,FACILITY,MOVING MOVING FACILITY TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF FACILITY(IES) FOR MOVING THE ITEM. 1D AND 1A MODE REPLY12AH85 BMGZD /D/ 07CHAIN,HALTER HALTER CHAIN AN INDICATION OF WHETHER OR NOT A HALTER CHAIN IS INCLUDED. SELECT REPLY CODE 10AA49 BMHBD /D/ 07WHEEL,CASTER,FULL FULL CASTER WHEEL AN INDICATION OF WHETHER OR NOT A FULL CASTER WHEEL/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BMHCJ 04DIAMETER,BUTT BUTT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR BUTT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BMHDD /D/ 07FEATURE,ADJUSTMENT,CROWN VARIATION,STRIKE-OFF PLATE STRIKE-OFF PLATE CROWN VARIATION ADJUSTMENT FEATURE AN INDICATION OF WHETHER OR NOT A STRIKE-OFF PLATE CROWN VARIATION ADJUSTMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BMHFJ 04HEIGHT,OVERALL,HOPPER HOPPER OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE HOPPER. 2D AND 1B MODE REPLY21AA051AC20 BMHGJ 04WIDTH,OVERALL,HOPPER HOPPER OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A HOPPER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BMHHJ 04LENGTH,OVERALL,HOPPER HOPPER OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE HOPPER. 2D AND 1B MODE REPLY21AA051AC20 BMHJJ 10CAPACITY,HOPPER HOPPER CAPACITY THE LOAD THAT THE HOPPER WILL ACCOMMODATE. 1D AND 1B MODE REPLY12AG67 BMHKJ T04WIDTH RANGE,SPREAD SPREAD WIDTH RANGE THE MINIMUM AND MAXIMUM WIDTH THE ITEM IS DESIGNED TO SPREAD. 1D AND 1F MODE REPLY11AA05 BMHLJ T04DEPTH RANGE,SPREAD SPREAD DEPTH RANGE THE MINIMUM AND MAXIMUM DEPTH THE ITEM IS DESIGNED TO SPREAD. 1D AND 1F MODE REPLY11AA05 BMHMD 18TYPE,LIFT LIFT TYPE INDICATES THE TYPE OF LIFT PROVIDED. SELECT REPLY CODE 10AE15 BMHND /D/ 07FEATURE,TRANSPORTING,KNOCKDOWN KNOCKDOWN TRANSPORTING FEATURE AN INDICATION OF WHETHER OR NOT A KNOCKDOWN TRANSPORTING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BMHPG /D/ 10RANGE,CAPACITY,RATED RATED CAPACITY RANGE THE CAPACITY RANGE FOR WHICH THE ITEM IS RATED. FULL TEXT WRITE-IN 0 BMHQD 18TYPE,CONNECTION,HOSE HOSE CONNECTION TYPE INDICATES THE TYPE OF HOSE CONNECTION PROVIDED. SELECT REPLY CODE 10AB76 BMHRJ 10SIZE,CONNECTION,HOSE HOSE CONNECTION SIZE DESIGNATES THE SIZE OF THE HOSE CONNECTION. 2D AND 1B MODE REPLY21AA051AC20 BMHSJ 04LENGTH,STROKE,PISTON PISTON STROKE LENGTH A MEASUREMENT OF THE DISTANCE THE PISTON TRAVELS PER STROKE. 2D AND 1B MODE REPLY21AA051AC20 BMHTJ 10CONSUMPTION,AIR AIR CONSUMPTION THE AMOUNT OF AIR REQUIRED TO OPERATE THE ITEM. 1D AND 1B MODE REPLY12AG67 BMHWD 18TYPE,GUIDE GUIDE TYPE INDICATES THE TYPE OF GUIDE PROVIDED. SELECT REPLY CODE 10AD58 BMHXJ 04DISTANCE BETWEEN JAWS DISTANCE BETWEEN JAWS THE DISTANCE BETWEEN THE JAWS. 2D AND 1B MODE REPLY21AA051AC20 BMHYJ 04WIDTH ACROSS GUIDES,OVERALL OVERALL WIDTH ACROSS GUIDES AN OVERALL MEASUREMENT ACROSS GUIDES TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM.IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BMHZD 19CONDITION,SURFACE,REMOVABLE BACKING REMOVABLE BACKING SURFACE CONDITION THE CONDITION OF THE REMOVABLE BACKING WITH RESPECT TO THE TEXTURE OF THE SURFACE. SELECT REPLY CODE 10AK39 BMJBD /D/ 07FEATURE,ELASTIC ELASTIC FEATURE AN INDICATION OF WHETHER OR NOT AN ELASTIC FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BMJCD 19PERIOD,AFTERGLOW AFTERGLOW PERIOD AN INDICATION OF THE PERIOD OF AFTERGLOW. SELECT REPLY CODE 10AB79 BMJDD 18TYPE,BACKING,ADHESIVE ADHESIVE BACKING TYPE INDICATES THE TYPE OF ADHESIVE BACKING PROVIDED. SELECT REPLY CODE 10AB47 BMJFD /D/ 07STRIP,SEPARATOR SEPARATOR STRIP AN INDICATION OF WHETHER OR NOT A SEPARATOR STRIP IS INCLUDED. SELECT REPLY CODE 10AA49 BMJGA /D/ 19IDENTIFICATION,PATTERN/STYLE PATTERN/STYLE IDENTIFICATION A DESIGNATION ASSIGNED TO THE PATTERN OR STYLE FOR THE PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 BMJHJ /D/ 10STRENGTH AT 25 PCT DEFLECTION,COMPRESSION COMPRESSION STRENGTH AT 25 PCT DEFLECTION THE SQUEEZING LOAD AN ITEM CAN WITHSTAND WITHOUT BREAKING AT 25 PERCENT DEFLECTION. 2D AND 1B MODE REPLY22AB161AC20 BMJJD /D/ 19CHARACTERISTIC,PLASTIC PLASTIC CHARACTERISTIC AN INDICATION OF THE PROPERTY CHARACTERISTICS OF THE PLASTIC. SELECT REPLY CODE 10AE98 BMJKG 10FLOW RATING FLOW RATING THE AMOUNT OF FLOW ALLOWABLE UNDER A GIVEN PRESSURE. FULL TEXT WRITE-IN 0 BMJLG /D/ 19SOURCE,RATE,FLOW FLOW RATE SOURCE AN INDICATION OF THE REFERENCE SOURCE OF THE FLOW RATE. FULL TEXT WRITE-IN 0 BMJMD /D/ 09MATERIAL,PLASTIC PLASTIC MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PLASTIC IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BMJND /D/ 07MARKINGS,CODING/SPECIAL,COLOR COLOR CODING/SPECIAL MARKINGS AN INDICATION OF WHETHER OR NOT COLOR CODING AND/OR SPECIAL MARKINGS ARE INCLUDED. SELECT REPLY CODE 10AA49 BMJPD 01COLOR CODING COLOR CODING THE HUE OR TINT OF THE COLOR CODING. SELECT REPLY CODE 10AD06 BMJQD 18TYPE,CODING,ADDITIONAL COLOR ADDITIONAL COLOR CODING TYPE INDICATES THE TYPE OF ADDITIONAL COLOR CODING PROVIDED. SELECT REPLY CODE 10AL21 BMJRJ T04DIAMETER RANGE,BUNDLE BUNDLE DIAMETER RANGE THE MINIMUM AND MAXIMUM RANGE OF THE LENGTHS OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BUNDLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1F MODE REPLY11AA05 BMJSF /D/T10RANGE IN DEG FAHRENHEIT,TEMP,OPERATING OPERATING TEMP RANGE IN DEG FAHRENHEIT THE MINIMUM AND MAXIMUM OPERATING TEMPERATURE FOR WHICH THE ITEM IS RATED,EXPRESSED IN DEGREES FAHRENHEIT. 1F MODE REPLY 0 BMJTJ 10HARDNESS RATING,DUROMETER DUROMETER HARDNESS RATING A NUMERIC VALUE THAT REFLECTS THE DUROMETER SCALE HARDNESS RATING OF A NONMETALLIC ITEM. 1D AND 1B MODE REPLY11AC20 BMJWD 18TYPE,YARN YARN TYPE INDICATES THE TYPE OF YARN PROVIDED. SELECT REPLY CODE 10AL79 BMJXD /D/ 07JACKET,BRAIDED BRAIDED JACKET AN INDICATION OF WHETHER OR NOT A BRAIDED JACKET(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BMJYD /D/ 09MATERIAL,TREATMENT TREATMENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE WITH WHICH THE ITEM IS TREATED. SELECT REPLY CODE 10AD09 BMJZD /D/ 07FEATURE,OILED OILED FEATURE AN INDICATION OF WHETHER OR NOT AN OILED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BMKBD 18TYPE FOR WHICH DESIGNED,SYSTEM,PRESSURE FUELING PRESSURE FUELING SYSTEM TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF PRESSURE FUELING SYSTEM FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AN34 BMKCD /D/ 07INSERT,WIRE WIRE INSERT AN INDICATION OF WHETHER OR NOT A WIRE INSERT IS INCLUDED. SELECT REPLY CODE 10AA49 BMKDD /D/ 07REEL,HOSE,FUELING FUELING HOSE REEL AN INDICATION OF WHETHER OR NOT A FUELING HOSE REEL(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BMKFJ 10FLOW RATE,DISCHARGE,MAXIMUM,SINGLE POINT FUELING NOZZLE SINGLE POINT FUELING NOZZLE MAXIMUM DISCHARGE FLOW RATE THE MAXIMUM RATED DISCHARGE DELIVERED BY THE SINGLE POINT FUELING NOZZLE. 1D AND 1B MODE REPLY11AC64 BMKGD /D/ 07METER,FUEL FUEL METER AN INDICATION OF WHETHER OR NOT A FUEL METER IS INCLUDED. SELECT REPLY CODE 10AA49 BMKHD /D/ 09MATERIAL,TRAILER TRAILER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TRAILER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BMKJD /D/ 07ASSEMBLY,TOWING,TRAILER PINTLE TRAILER PINTLE TOWING ASSEMBLY AN INDICATION OF WHETHER OR NOT A TRAILER PINTLE TOWING ASSEMBLY IS INCLUDED. SELECT REPLY CODE 10AA49 BMKKD 18TYPE,STEERING,TRAILER TRAILER STEERING TYPE INDICATES THE TYPE OF STEERING MECHANISM PROVIDED ON THE TRAILER. SELECT REPLY CODE 10AE83 BMKLD 11METHOD,PRIMING PRIMING METHOD THE MEANS BY WHICH THE ITEM IS PRIMED. SELECT REPLY CODE 10AC58 BMKMD 18TYPE,EXTENSION EXTENSION TYPE INDICATES THE TYPE OF EXTENSION PROVIDED. SELECT REPLY CODE 10AK95 BMKND 18TYPE,END,DISPENSING DISPENSING END TYPE INDICATES THE TYPE OF DISPENSING END PROVIDED. SELECT REPLY CODE 10AM35 BMKPD /D/ 07FITTING,LOADER LOADER FITTING AN INDICATION OF WHETHER OR NOT A LOADER FITTING IS INCLUDED. SELECT REPLY CODE 10AA49 BMKQD /D/ 07FEATURE,DISENGAGEMENT FROM FOLLOWER,PUSH HANDLE PUSH HANDLE DISENGAGEMENT FROM FOLLOWER FEATURE AN INDICATION OF WHETHER OR NOT A PUSH HANDLE DISENGAGEMENT FROM FOLLOWER FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BMKRD /D/ 07TANK,STORAGE,LUBRICANT LUBRICANT STORAGE TANK AN INDICATION OF WHETHER OR NOT A LUBRICANT STORAGE TANK IS INCLUDED. SELECT REPLY CODE 10AA49 BMKSD 11METHOD,OPERATION,LUBRICANT PUMP LUBRICANT PUMP OPERATION METHOD THE MEANS USED TO OPERATE THE LUBRICANT PUMP. SELECT REPLY CODE 10AC58 BMKTJ 10CAPACITY RATING,COMPRESSOR,AIR AIR COMPRESSOR CAPACITY RATING THE RATED CAPACITY OF THE AIR COMPRESSOR. 1D AND 1B MODE REPLY12AG67 BMKWD /D/ 07CHARGER,BATTERY BATTERY CHARGER AN INDICATION OF WHETHER OR NOT A BATTERY CHARGER IS INCLUDED. SELECT REPLY CODE 10AA49 BMKXJ A18TYPE AND QUANTITY,LIGHT LIGHT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF LIGHT(S). 1D AND 1A MODE REPLY12AG41 BMKYD 18TYPE,TREATMENT TREATMENT TYPE INDICATES THE TYPE OF TREATMENT PROVIDED. SELECT REPLY CODE 10AK89 BMKZJ 04LENGTH,LENS LENS LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE LENS,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BMLBJ 04DIAMETER,LENS LENS DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A LENS,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BMLCJ 04WIDTH,LENS LENS WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE LENS,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BMLDD /D/ 07FEATURE,PIVOT,CASE LENS CASE LENS PIVOT FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE IS PROVIDED FOR THE LENS TO PIVOT INTO THE CASE. SELECT REPLY CODE 10AB22 BMLFD /D/ 07FEATURE,FOLDING,LENS HANDLE LENS HANDLE FOLDING FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE IS PROVIDED FOR THE HANDLE TO FOLD OVER THE LENS. SELECT REPLY CODE 10AB22 BMLGD 18TYPE,STAND,MOUNTING MOUNTING STAND TYPE INDICATES THE TYPE OF MOUNTING STAND PROVIDED. SELECT REPLY CODE 10AA78 BMLHD /D/ 07FEATURE,DESIGN,EYE ORBIT EYE ORBIT DESIGN FEATURE AN INDICATION OF WHETHER OR NOT AN EYE ORBIT DESIGN FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BMLJD /D/ 07HEADSPRING,DETACHABLE DETACHABLE HEADSPRING AN INDICATION OF WHETHER OR NOT A DETACHABLE HEADSPRING IS INCLUDED. SELECT REPLY CODE 10AA49 BMLKD /D/ 07SCALE,FIELD FIELD SCALE AN INDICATION OF WHETHER OR NOT A FIELD SCALE IS INCLUDED. SELECT REPLY CODE 10AA49 BMLLG /D/ 10RANGE,SCALE,FIELD FIELD SCALE RANGE AN INDICATION OF THE MINIMUM AND MAXIMUM LIMITS OF THE FIELD SCALE. FULL TEXT WRITE-IN 0 BMLMD 02DESIGN,BINOCULAR BINOCULAR DESIGN THE DESIGN OF THE BINOCULAR. SELECT REPLY CODE 10AM04 BMLNJ 04LENGTH,OBJECTIVE OBJECTIVE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE OBJECTIVE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BMLPJ 04WIDTH,FIELD,VIEWING,LENS LENS VIEWING FIELD WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE AREA VISIBLE THROUGH THE LENS,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BMLQG 04SIZE,FIELD,VIEWING VIEWING FIELD SIZE DESIGNATES THE SIZE OF THE TOTAL SURFACE OF THE FIELD OF VIEW. FULL TEXT WRITE-IN 0 BMLRD /D/ 07HEADBAND HEADBAND AN INDICATION OF WHETHER OR NOT A HEADBAND IS PROVIDED. SELECT REPLY CODE 10AB22 BMLSG 10INCREMENT,SMALLEST,FIELD SCALE FIELD SCALE SMALLEST INCREMENT THE SMALLEST INCREMENT DESIGNATED BY THE MARKINGS ON THE FIELD SCALE. FULL TEXT WRITE-IN 0 BMLTD 18TYPE,NONSTEREOSCOPIC NONSTEREOSCOPIC TYPE INDICATES THE TYPE OF NONSTEREOSCOPIC UNIT PROVIDED. SELECT REPLY CODE 10AK95 BMLWD 19POSITION,TUBE,BODY BODY TUBE POSITION AN INDICATION OF THE POSITION OF THE BODY TUBE. SELECT REPLY CODE 10AF63 BMLXD 11METHOD,CALCULATION,ADJUSTABLE DRAWTUBE ADJUSTABLE DRAWTUBE CALCULATION METHOD THE MEANS PROVIDED FOR CALCULATION ON AN ADJUSTABLE DRAWTUBE. SELECT REPLY CODE 10AJ12 BMLYJ 04THICKNESS,AXIAL AXIAL THICKNESS A MEASUREMENT OF THE AXIAL THICKNESS OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BMLZD /D/ 07FEATURE,INTERCHANGEABILITY,BODY TUBE BODY TUBE INTERCHANGEABILITY FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE FOR INTERCHANGEABILITY OF BODY TUBES IS PROVIDED. SELECT REPLY CODE 10AB22 BMMBD /D/ 07ANALYZER,TUBE,BODY BODY TUBE ANALYZER AN INDICATION OF WHETHER OR NOT A BODY TUBE ANALYZER IS INCLUDED. SELECT REPLY CODE 10AA49 BMMCD /D/ 07LENS,BERTRAND,BODY TUBE BODY TUBE BERTRAND LENS AN INDICATION OF WHETHER OR NOT THE BODY TUBE IS PROVIDED WITH A BERTRAND LENS. SELECT REPLY CODE 10AB22 BMMDD /D/ 07SLOT,ACCESSROY,BODY TUBE BODY TUBE ACCESSROY SLOT AN INDICATION OF WHETHER OR NOT A BODY TUBE ACCESSORY SLOT IS PROVIDED. SELECT REPLY CODE 10AB22 BMMFD 14SHAPE,STAGE STAGE SHAPE THE PHYSICAL CONFIGURATION OF THE STAGE. SELECT REPLY CODE 10AD07 BMMGD /D/ 09MATERIAL,STAGE STAGE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE STAGE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BMMHD 18TYPE,STAGE STAGE TYPE INDICATES THE TYPE OF STAGE PROVIDED. SELECT REPLY CODE 10AK54 BMMJD /D/ 07FEATURE,CENTERING CENTERING FEATURE AN INDICATION OF WHETHER OR NOT A CENTERING FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BMMKJ T10RANGE,WAVELENGTH WAVELENGTH RANGE AN INDICATION OF THE WAVELENGTH MINIMUM AND MAXIMUM LIMITS. 1D AND 1F MODE REPLY11AD75 BMMLD /D/ 07PRISM,QUARTZ QUARTZ PRISM AN INDICATION OF WHETHER OR NOT A QUARTZ PRISM IS INCLUDED. SELECT REPLY CODE 10AA49 BMMMD /D/ 07CHARGER,TRICKLE TRICKLE CHARGER AN INDICATION OF WHETHER OR NOT A TRICKLE CHARGER IS INCLUDED. SELECT REPLY CODE 10AA49 BMMNJ 04THICKNESS,AXIAL,OVERALL,COMPOUND LENS COMPOUND LENS OVERALL AXIAL THICKNESS AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION THROUGH THE CENTER OF THE OUTER SURFACES OF A COMPOUND LENS,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BMMPJ 04THICKNESS,EDGE,COMPOUND LENS COMPOUND LENS EDGE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION ACROSS THE EDGE OF A COMPOUND LENS FROM ONE SURFACE TO THE OTHER,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BMMQB /D/ 04RADIUS,SURFACE,LEFT,ELEMENT ELEMENT LEFT SURFACE RADIUS THE RADIUS OF THE LEFT SURFACE OF THE ELEMENT. 1B MODE REPLY 0 BMMRB /D/ 04RADIUS,SURFACE,RIGHT,ELEMENT ELEMENT RIGHT SURFACE RADIUS THE RADIUS OF THE RIGHT SURFACE OF THE ELEMENT. 1B MODE REPLY 0 BMMSJ 04LENGTH,FOCAL,EQUIVALENT EQUIVALENT FOCAL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION FROM THE CENTER OF A LENS TO EITHER OF ITS FOCAL POINTS,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BMMTJ 04LENGTH,FOCAL,BACK BACK FOCAL LENGTH A MEASUREMENT OF THE LONGEST RECIPROCAL DIMENSION FROM THE BACK SURFACE OF THE LENS TO THE SECONDARY FOCAL POINT,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BMMWJ 04LENGTH,FOCAL,FRONT FRONT FOCAL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION FROM THE PRIMARY FOCAL POINT TO THE FRONT SURFACE OF A LENS. 1D AND 1B MODE REPLY11AA05 BMMXJ 10INDEX,REFRACTION REFRACTION INDEX AN INDICATION OF THE RATIO OF THE SPEED OF LIGHT IN THE FIRST MEDIUM TO ITS SPEED IN THE SECOND MEDIUM. 1D AND 1B MODE REPLY11AC20 BMMYD 07ADJUSTABILITY,SLIT SLIT ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE SLIT IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BMMZB 10CONSTANT,ABBE ABBE CONSTANT THE FIXED ANGLE OF REFRACTION OF THE ABBE PRISM. 1B MODE REPLY 0 BMNBD /D/ 07PROTECTOR,OVERLOAD,ELECTRICAL ELECTRICAL OVERLOAD PROTECTOR AN INDICATION OF WHETHER OR NOT AN ELECTRICAL OVERLOAD PROTECTOR IS PROVIDED. SELECT REPLY CODE 10AB22 BMNCD 11METHOD,STORAGE,DATA DATA STORAGE METHOD THE METHOD USED TO STORE AND/OR RETRIEVE INFORMATION ON THE ITEM. SELECT REPLY CODE 10AK95 BMNGJ 04HEIGHT BEHIND MOUNTING FLANGE,BODY,METER METER BODY HEIGHT BEHIND MOUNTING FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BMNHJ 04THICKNESS,CLADDING CLADDING THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE CLADDING COVERING THE ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 BMNJD /D/ 08LOCATION,CLADDING CLADDING LOCATION INDICATES THE LOCATION OF THE CLADDING ON THE ITEM. SELECT REPLY CODE 10AJ91 BMNKJ /D/ 04WIDTH ACCOMMODATED,CONDUCTOR,MAXIMUM MAXIMUM CONDUCTOR WIDTH ACCOMMODATED THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A CONDUCTOR THE ITEM WILL ACCOMMODATE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BMNLJ /D/ 04DIAMETER ACCOMMODATED,CONDUCTOR,MAXIMUM MAXIMUM CONDUCTOR DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE CONDUCTOR,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BMNMJ 04DEPTH,METER BARREL METER BARREL DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BMNNJ /D/ 04DISTANCE ALONG HORIZONTAL AXIS,CENTER TO CENTER,PERFORATION PERFORATION CENTER TO CENTER DISTANCE ALONG HORIZONTAL AXIS NONE. 2D AND 1B MODE REPLY21AA051AC20 BMNPJ /D/ 04DISTANCE ALONG VERTICAL AXIS,CENTER TO CENTER,PERFORATION PERFORATION CENTER TO CENTER DISTANCE ALONG VERTICAL AXIS NONE. 2D AND 1B MODE REPLY21AA051AC20 BMNQJ 04LENGTH,ELONGATION,PERFORATION PERFORATION ELONGATION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BMNRJ 04WIDTH,ELONGATION,PERFORATION PERFORATION ELONGATION WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BMNSJ 04DISTANCE ALONG UPWARD SLOPE,CENTER TO CENTER,PERFORATION PERFORATION CENTER TO CENTER DISTANCE ALONG UPWARD SLOPE NONE. 2D AND 1B MODE REPLY21AA051AC20 BMNTJ 04DISTANCE ALONG DOWNWARD SLOPE,CENTER TO CENTER,PERFORATION PERFORATION CENTER TO CENTER DISTANCE ALONG DOWNWARD SLOPE NONE. 2D AND 1B MODE REPLY21AA051AC20 BMNWA /D/ 12QUANTITY PER SQUARE INCH,HOLE HOLE QUANTITY PER SQUARE INCH NONE. 1A MODE REPLY 0 BMNXJ 04WIDTH,STRAND STRAND WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BMNYJ 04THICKNESS,STRAND STRAND THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BMNZJ 04WIDTH ACROSS FLATS,CROSS-SECTIONAL CROSS-SECTIONAL WIDTH ACROSS FLATS THE SHORTEST STRAIGHT LINE BETWEEN CROSS-SECTIONAL FLATS,PERPENDICULAR TO THE HEIGHT OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BMPBJ 04RADIUS,CROSS-SECTIONAL CROSS-SECTIONAL RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPCJ /D/ 04DIAMETER,TIP,BASE FLANGE BASE FLANGE TIP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPDJ /D/ 04THICKNESS,TIP,BASE FLANGE BASE FLANGE TIP THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPFJ /D/ 04RADIUS OF FILLET AT BULB,FLANGE,TOP,LEFT SIDE LEFT SIDE TOP FLANGE RADIUS OF FILLET AT BULB NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPGJ /D/ 04RADIUS OF FILLET AT BULB,FLANGE,BASE BASE FLANGE RADIUS OF FILLET AT BULB NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPHJ /D/ 04LENGTH,TAPER,BASE FLANGE INNER BASE FLANGE INNER TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPJJ /D/ 04LENGTH,TAPER,BASE FLANGE OUTER BASE FLANGE OUTER TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPKJ /D/ 04LENGTH,TAPER,LEFT SIDE FLANGE OUTER LEFT SIDE FLANGE OUTER TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPLJ /D/ 04LENGTH,TAPER,LEFT SIDE FLANGE INNER LEFT SIDE FLANGE INNER TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPMJ 04HEIGHT,OVERALL,TOE TOE OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPNJ 04DISTANCE,FLANGE OUTER FACE TO BOTTOM FLANGE CENTERLINE FLANGE OUTER FACE TO BOTTOM FLANGE CENTERLINE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPPJ 04RADIUS,CORNER,BOTTOM FLANGE RIGHT END,OUTER FACE OUTER FACE BOTTOM FLANGE RIGHT END CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPQJ 04THICKNESS,FLANGE,RIGHT SIDE BOTTOM RIGHT SIDE BOTTOM FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPRJ 04THICKNESS,FLANGE,LEFT SIDE BOTTOM LEFT SIDE BOTTOM FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPSJ /D/ 04RADIUS OF FILLET AT BULB,FLANGE,TOP,RIGHT SIDE RIGHT SIDE TOP FLANGE RADIUS OF FILLET AT BULB NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPTJ /D/ 04RADIUS AT TOE,LEG LEG RADIUS AT TOE NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPWJ 04DISTANCE TO CENTER OF BOTH FLANGES,RIGHT SIDE RIGHT SIDE DISTANCE TO CENTER OF BOTH FLANGES NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPXJ 04DISTANCE TO CENTER OF BOTH FLANGES,LEFT SIDE LEFT SIDE DISTANCE TO CENTER OF BOTH FLANGES NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPYJ /D/ 04RADIUS WHERE END FLANGE JOINS TOP FLANGE,CORNER,RIGHT SIDE INNER RIGHT SIDE INNER CORNER RADIUS WHERE END FLANGE JOINS TOP FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BMPZJ /D/ 04RADIUS WHERE END FLANGE JOINS TOP FLANGE,CORNER,RIGHT SIDE OUTER RIGHT SIDE OUTER CORNER RADIUS WHERE END FLANGE JOINS TOP FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BMQBJ T10RANGE,ELEVATION ELEVATION RANGE AN INDICATION OF THE MINIMUM TO THE MAXIMUM ELEVATION OF THE ITEM. 1D AND 1F MODE REPLY11AA05 BMQCD 18TYPE,FOOT FOOT TYPE INDICATES THE TYPE OF FEET PROVIDED ON THE ITEM. SELECT REPLY CODE 10AK95 BMQDD /D/ 07CALIBRATED HEAD FOR DEG OF ROTATION CALIBRATED HEAD FOR DEG OF ROTATION AN INDICATION OF WHETHER OR NOT A CALIBRATED HEAD FOR DEGREE OF ROTATION IS INCLUDED. SELECT REPLY CODE 10AA49 BMQFG /D/ 19CAPACITY,PRODUCTIVE,MAXIMUM MAXIMUM PRODUCTIVE CAPACITY THE MAXIMUM PRODUCTIVE CAPACITY OF THE ITEM. FULL TEXT WRITE-IN 0 BMQGD /D/ 07SCREW,TRIPOD,ADJUSTABLE ADJUSTABLE TRIPOD SCREW AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE TRIPOD SCREW IS INCLUDED. SELECT REPLY CODE 10AA49 BMQHD 18TYPE,MARGIN MARGIN TYPE INDICATES THE TYPE OF MARGIN PROVIDED ON THE ITEM. SELECT REPLY CODE 10AK54 BMQJJ 10SIZE,MARGIN MARGIN SIZE DESIGNATES THE SIZE OF MARGIN ON THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BMQKJ B04SIZE ACCOMMODATED,PAPER,MAXIMUM MAXIMUM PAPER SIZE ACCOMMODATED DESIGNATES THE MAXIMUM PAPER SIZE THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1F MODE REPLY11AA05 BMQLJ /D/B04SIZE ACCOMMODATED,FILM/PLATE,CUT CUT FILM/PLATE SIZE ACCOMMODATED DESIGNATES THE SIZE CUT FILM/PLATE THAT THE ITEM WILL ACCOMMODATE. 1D AND 1F MODE REPLY11AA05 BMQMA 12QUANTITY,SEPTUM SEPTUM QUANTITY THE NUMBER OF SEPTUM PROVIDED. 1A MODE REPLY 0 BMQNA 12QUANTITY,SLIDE SLIDE QUANTITY THE NUMBER OF SLIDES PROVIDED. 1A MODE REPLY 0 BMQPD /D/ 09MATERIAL,SLIDE SLIDE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SLIDE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BMQQJ B04SIZE,MOUNT,SLIDE SLIDE MOUNT SIZE DESIGNATES THE SIZE OF THE SLIDE MOUNT. 1D AND 1F MODE REPLY11AA05 BMQRD 18TYPE,FILM,SLIDE SLIDE FILM TYPE INDICATES THE TYPE OF SLIDE FILM FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AG37 BMQSA 12QUANTITY ACCOMMODATED,SLIDE,FILM FILM SLIDE QUANTITY ACCOMMODATED THE NUMBER OF FILM SLIDES THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 BMQTD /D/ 07COVER,TRANSPARENT TRANSPARENT COVER AN INDICATION OF WHETHER OR NOT A TRANSPARENT COVER IS PROVIDED. SELECT REPLY CODE 10AB22 BMQWA 12QUANTITY PER BINDER QUANTITY PER BINDER THE NUMBER OF ITEM(S) SUPPLIED PER BINDER. 1A MODE REPLY 0 BMQXG /D/ 11METHOD,BINDING BINDING METHOD THE MEANS BY WHICH THE ITEM IS BOUND. FULL TEXT WRITE-IN 0 BMQYD /D/ 07SPACE,MARKING,IDENTIFICATION IDENTIFICATION MARKING SPACE AN INDICATION OF WHETHER OR NOT AN IDENTIFICATION MARKING SPACE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BMQZJ 04THICKNESS ACCOMMODATED,FILTER FILTER THICKNESS ACCOMMODATED A MEASUREMENT OF THE SMALLEST DIMENSION OF THE ACCOMMODATED FILTER,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BMRBA 12QUANTITY,DEVICE,REWIND REWIND DEVICE QUANTITY THE NUMBER OF REWIND DEVICE(S) PROVIDED. 1A MODE REPLY 0 BMRCD 18TYPE,DEVICE,REWIND REWIND DEVICE TYPE INDICATES THE TYPE OF REWIND DEVICE PROVIDED. SELECT REPLY CODE 10AF46 BMRDD /D/ 07DEVICE,TENSION TENSION DEVICE AN INDICATION OF WHETHER OR NOT A TENSION DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 BMRFD /D/ 07WINDER,TIGHT TIGHT WINDER AN INDICATION OF WHETHER OR NOT A TIGHT WINDER IS INCLUDED. SELECT REPLY CODE 10AA49 BMRGD /D/ 07SUBBASE,MOUNTED MOUNTED SUBBASE AN INDICATION OF WHETHER OR NOT A MOUNTED SUBBASE IS PROVIDED. SELECT REPLY CODE 10AB22 BMRHD 18TYPE,DEVICE,REEL LOCKING REEL LOCKING DEVICE TYPE INDICATES THE TYPE OF DEVICE USED TO LOCK THE REEL. SELECT REPLY CODE 10AE36 BMRJD 18TYPE,MOUNTING,COMPONENT COMPONENT MOUNTING TYPE INDICATES THE TYPE OF COMPONENT MOUNTING PROVIDED. SELECT REPLY CODE 10AM39 BMRKF T10RATIO,GEAR GEAR RATIO THE NUMBER OF TURNS OF THE DRIVING GEAR IN RELATION TO ONE OR MORE DRIVE GEARS. 1F MODE REPLY 0 BMRLD /D/ 07GLASS GLASS AN INDICATION OF WHETHER OR NOT A GLASS IS INCLUDED. SELECT REPLY CODE 10AA49 BMRMG 04SIZE ACCOMMODATED,NEGATIVE NEGATIVE SIZE ACCOMMODATED DESIGNATES THE NEGATIVE SIZE THE ITEM IS DESIGNED TO ACCOMMODATE. FULL TEXT WRITE-IN 0 BMRNJ 04LENGTH,OPENING,DIE-CUT DIE-CUT OPENING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A DIE-CUT OPENING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BMRPD 18TYPE,PROCESSING PROCESSING TYPE INDICATES THE TYPE OF PROCESSING OF THE ITEM. SELECT REPLY CODE 10AN35 BMRQJ 04HEIGHT,CUT CUT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE CUT,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BMRRD 19INGREDIENT,ACTIVE ACTIVE INGREDIENT THE ACTIVE INGREDIENT WHICH PRODUCES OR IS CAPABLE OF PRODUCING AN EFFECT ON THE ITEM. SELECT REPLY CODE 10AJ08 BMRSB 10RATIO IN PERCENT,CONCENTRATION CONCENTRATION RATIO IN PERCENT THE RELATIVE VALUES BETWEEN TWO SUBSTANCES,EXPRESSED IN PERCENT. 1B MODE REPLY 0 BMRTD 11METHOD,DISPERSING DISPERSING METHOD THE MEANS USED TO DISPERSE THE ITEM. SELECT REPLY CODE 10AF11 BMRWD /D/ 18TYPE,ELECTRODE,CARBON ARC CARBON ARC ELECTRODE TYPE INDICATES THE TYPE OF CARBON ARC ELECTRODE(S) PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AG57 BMRXG /D/ 04SIZE,ELECTRODE,CARBON ARC CARBON ARC ELECTRODE SIZE DESIGNATES THE SIZE OF THE TOTAL SURFACE OF A CARBON ARC ELECTRODE. FULL TEXT WRITE-IN 0 BMRYG 04SIZE,PRINT PRINT SIZE DESIGNATES THE SIZE OF THE TOTAL SURFACE OF A PRINT. FULL TEXT WRITE-IN 0 BMRZJ 04LENGTH,FILM,LOADED LOADED FILM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE LOADED FILM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BMSBL 16STYLE,LENS,SINGLE SINGLE LENS STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF A SINGLE LENS. 1L MODE REPLY 0 BMSCL 16STYLE,LENS,COMPOUND COMPOUND LENS STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF A COMPOUND LENS. 1L MODE REPLY 0 BMSDL 16STYLE,LENS,INDIVIDUAL INDIVIDUAL LENS STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF AN INDIVIDUAL LENS. 1L MODE REPLY 0 BMSFD /D/ 09MATERIAL,BACKING,REFLECTIVE REFLECTIVE BACKING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE REFLECTIVE BACKING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BMSGD /D/ 19SURFACE,POLISHED POLISHED SURFACE AN INDICATION OF THE POLISHED SURFACE/S/ ON THE ITEM. SELECT REPLY CODE 10AJ91 BMSHJ 10DISPERSION DISPERSION THE VARIATION OF THE REFRACTIVE INDEX OF THE ITEM. 2D AND 1B MODE REPLY21AD751AC20 BMSJD /D/ 19SURFACE,PRODUCING,DIFFUSION DIFFUSION PRODUCING SURFACE AN INDICATION OF THE SURFACE/S/ ALTERED TO PROMOTE DIFFUSION. SELECT REPLY CODE 10AJ91 BMSKD /D/ 19SURFACE,REDUCING,REFLECTION REFLECTION REDUCING SURFACE AN INDICATION OF THE SURFACE/S/ TREATED WITH REFLECTION REDUCING FILM. SELECT REPLY CODE 10AJ91 BMSLD /D/ 09MATERIAL,PLATING,BEVELED/POLISHED EDGE BEVELED/POLISHED EDGE PLATING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE WITH WHICH THE BEVELED AND POLISHED EDGES ARE PLATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BMSMD /D/ 07PERIPHERY,POLISHED POLISHED PERIPHERY AN INDICATION OF WHETHER OR NOT A POLISHED PERIPHERY IS PROVIDED. SELECT REPLY CODE 10AB22 BMSNG 08LOCATION AND QUANTITY,EDGE,BEVELED BEVELED EDGE LOCATION AND QUANTITY INDICATES THE LOCATION AND NUMBER OF BEVELED EDGES. FULL TEXT WRITE-IN 0 BMSPJ /D/ 04ANGLE IN DEG,BEVEL BEVEL ANGLE IN DEG THE ANGLE OF THE BEVEL,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 BMSQD 19FEATURE,SIMILARITY SIMILARITY FEATURE INDICATES THE RELATIONSHIP OF ONE ITEM TO A SECOND. SELECT REPLY CODE 10AG93 BMSRD /D/ 07CROSS HAIRS,MOUNTED MOUNTED CROSS HAIRS AN INDICATION OF WHETHER OR NOT MOUNTED CROSS HAIRS ARE PROVIDED. SELECT REPLY CODE 10AB22 BMSSD 18TYPE,SCALE,MICROMETER MICROMETER SCALE TYPE INDICATES THE TYPE OF MICROMETER SCALE PROVIDED. SELECT REPLY CODE 10AM12 BMSTD /D/ 07DESIGN,USAGE,DISC INSERT DISC INSERT USAGE DESIGN AN INDICATION OF WHETHER OR NOT THE ITEM DESIGN PROVIDES FOR USE OF DISC INSERTS. SELECT REPLY CODE 10AB22 BMSWJ 04DISTANCE,WORKING WORKING DISTANCE THE DISTANCE AT WHICH THE ITEM IS CAPABLE OF SATISFACTORY OPERATION. 2D AND 1B MODE REPLY21AA051AC20 BMSXD 19FEATURE,COATING,LENS LENS COATING FEATURE AN INDICATION OF THE COATING FEATURE ON THE LENS. SELECT REPLY CODE 10AG57 BMSYD /D/ 07DIAPHRAGM,IRIS IRIS DIAPHRAGM AN INDICATION OF WHETHER OR NOT AN IRIS DIAPHRAGM IS INCLUDED. SELECT REPLY CODE 10AA49 BMSZD /D/ 07COLLAR,CORRECTION,COVER GLASS COVER GLASS CORRECTION COLLAR AN INDICATION OF WHETHER OR NOT A COVER GLASS CORRECTION COLLAR IS PROVIDED. SELECT REPLY CODE 10AB22 BMTBB 19APERTURE,NUMERIC NUMERIC APERTURE AN INDICATION OF THE NUMERIC APERTURE OF THE ITEM. 1B MODE REPLY 0 BMTDB /D/ 10APERTURE EXCLUDING FRONT ELEMENT,NUMERIC NUMERIC APERTURE EXCLUDING FRONT ELEMENT AN INDICATION OF THE NUMERIC APERTURE EXCLUDING THE FRONT ELEMENT. 1B MODE REPLY 0 BMTFJ /D/ 04LENGTH EXCLUDING FRONT ELEMENT,FOCAL FOCAL LENGTH EXCLUDING FRONT ELEMENT A MEASUREMENT OF THE LONGEST DIMENSION OF THE FOCUS,EXCLUDING THE FRONT ELEMENT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BMTGJ 04DISTANCE EXCLUDING FRONT ELEMENT,WORKING WORKING DISTANCE EXCLUDING FRONT ELEMENT THE DISTANCE,EXCLUDING THE FRONT ELEMENT,AT WHICH THE ITEM IS CAPABLE OF WORKING. 2D AND 1B MODE REPLY21AA051AC20 BMTHD 18TYPE,OBJECTIVE OBJECTIVE TYPE INDICATES THE TYPE OF OBJECTIVE PROVIDED. SELECT REPLY CODE 10AK54 BMTJL /D/ 19ARRANGEMENT,LENS LENS ARRANGEMENT THE ARRANGEMENT OF THE ASSEMBLED LENS/ES/. 1L MODE REPLY 0 BMTKD 19EYE FOR WHICH DESIGNED EYE FOR WHICH DESIGNED AN INDICATION OF THE EYE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AJ91 BMTLJ 04THICKNESS,FLANGE,INTERNAL INTERNAL FLANGE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF AN INTERNAL FLANGE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BMTMJ T04DIAMETER,INSIDE,PRESS FIT PRESS FIT INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO SURFACES OF A CIRCULAR ITEM MACHINED FOR PRESS FIT,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1F MODE REPLY11AA05 BMTNB 04SPACING IN DEG,ANGULAR,DRIVE FACILITY DRIVE FACILITY ANGULAR SPACING IN DEG THE ANGULAR SPACING BETWEEN DRIVE FACILITIES,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BMTPJ 04RADIUS FROM GEOMETRIC AXIS TO HOLE CENTER RADIUS FROM GEOMETRIC AXIS TO HOLE CENTER A MEASUREMENT OF THE DISTANCE FROM THE GEOMETRIC AXIS TO THE HOLE CENTER. 2D AND 1B MODE REPLY21AA051AC20 BMTQD 02DESIGN,GUIDE GUIDE DESIGN THE DESIGN OF THE GUIDE ON THE ITEM. SELECT REPLY CODE 10AK54 BMTRD 08LOCATION,GUIDE GUIDE LOCATION INDICATES THE LOCATION OF THE GUIDE ON THE ITEM. SELECT REPLY CODE 10AJ91 BMTSD /D/ 07SERRATION,ANNULAR,INTERNAL INTERNAL ANNULAR SERRATION AN INDICATION OF WHETHER OR NOT AN INTERNAL ANNULAR SERRATION(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BMTTD /D/ 07NOTCH,SETSCREW SETSCREW NOTCH AN INDICATION OF WHETHER OR NOT A SETSCREW NOTCH IS PROVIDED. SELECT REPLY CODE 10AB22 BMTWB /D/ 04RADIUS IN INCHES,SURFACE,CONVEX CONVEX SURFACE RADIUS IN INCHES THE RADIUS OF THE CONVEX SURFACE OF THE ITEM,EXPRESSED IN INCHES. 1B MODE REPLY 0 BMTXD 19FINISH,RIM RIM FINISH AN INDICATION OF THE FINISH ON THE RIM. SELECT REPLY CODE 10AA41 BMTYD 08LOCATION,GROOVE GROOVE LOCATION INDICATES THE LOCATION OF THE GROOVE ON THE ITEM. SELECT REPLY CODE 10AJ91 BMTZD /D/ 07CONSTRUCTION,ECCENTRIC ECCENTRIC CONSTRUCTION AN INDICATION OF WHETHER OR NOT OFF CENTER CONSTRUCTION IS PROVIDED. SELECT REPLY CODE 10AB22 BMWBJ 10ECCENTRICITY FROM GEOMETRIC AXIS,CELL CELL ECCENTRICITY FROM GEOMETRIC AXIS A MEASUREMENT OF THE CELL DEVIATION FROM THE GEOMETRIC AXIS. 1D AND 1B MODE REPLY11AA05 BMWCD /D/ 07FEATURE,UTILIZATION,ORIGINAL LUBRICANT DRUM ORIGINAL LUBRICANT DRUM UTILIZATION FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE IS INCLUDED TO PERMIT THE USE OF THE ORIGINAL LUBRICANT DRUM/S/. SELECT REPLY CODE 10AA49 BMWDA 12QUANTITY,HOSE,LUBRICANT LUBRICANT HOSE QUANTITY THE NUMBER OF LUBRICANT HOSES PROVIDED. 1A MODE REPLY 0 BMWFA 12QUANTITY,HOSE,AIR AIR HOSE QUANTITY THE NUMBER OF AIR HOSES PROVIDED. 1A MODE REPLY 0 BMWGA 12QUANTITY,FEED FEED QUANTITY THE NUMBER OF FEED(S) PROVIDED. 1A MODE REPLY 0 BMWHD 18TYPE,RESERVOIR RESERVOIR TYPE INDICATES THE TYPE OF RESERVOIR PROVIDED. SELECT REPLY CODE 10AM39 BMWJA 04SIZE,CONNECTION,OUTLET OUTLET CONNECTION SIZE DESIGNATES THE SIZE OF THE OUTLET CONNECTION INCLUDED ON THE ITEM. 1A MODE REPLY 0 BMWKD /D/ 18TYPE FOR WHICH DESIGNED,AIRLINE AIRLINE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF AIRLINE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BMWLD /D/ 07GLASS,SIGHT,OIL FEED OIL FEED SIGHT GLASS AN INDICATION OF WHETHER OR NOT AN OIL FEED SIGHT GLASS IS INCLUDED. SELECT REPLY CODE 10AA49 BMWMD /D/ 07ADJUSTABILITY UNDER PRESSURE ADJUSTABILITY UNDER PRESSURE AN INDICATION OF WHETHER OR NOT THE ITEM IS ADJUSTABLE UNDER PRESSURE. SELECT REPLY CODE 10AC06 BMWND /D/ 07REPLACEABILITY,BOWL BOWL REPLACEABILITY AN INDICATION OF WHETHER OR NOT THE BOWL IS REPLACEABLE. SELECT REPLY CODE 10AG84 BMWPA /D/ 16STYLE DESIGNATOR,SPOUT SPOUT STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SPOUT. 1A MODE REPLY 0 BMWQJ 04LENGTH ACCOMMODATED,HOSE HOSE LENGTH ACCOMMODATED A MEASUREMENT OF THE LONGEST DIMENSION OF THE HOSE THE ITEM WILL ACCOMMODATE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BMWRJ 04DIAMETER ACCOMMODATED,HOSE HOSE DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE HOSE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BMWSJ 04DIAMETER,OUTSIDE,REEL RIM REEL RIM OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE REEL RIM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BMWTJ 04WIDTH,HUB,REEL REEL HUB WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE REEL HUB,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BMWWD 18TYPE,CONNECTION,FIXED REEL HOSE PIPING FIXED REEL HOSE PIPING CONNECTION TYPE INDICATES THE TYPE OF FIXED REEL HOSE PIPING CONNECTION. SELECT REPLY CODE 10AB76 BMWXD /D/ 07MOTOR,ELECTRIC ELECTRIC MOTOR AN INDICATION OF WHETHER OR NOT AN ELECTRIC MOTOR IS INCLUDED. SELECT REPLY CODE 10AA49 BMWYD /D/ 07SWITCH,MOTOR MOTOR SWITCH AN INDICATION OF WHETHER OR NOT A MOTOR SWITCH IS INCLUDED. SELECT REPLY CODE 10AA49 BMWZJ /D/ 04WIDTH,PLATE,MOUNTING MOUNTING PLATE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING PLATE,IN DISTINCTION FROM THICKNESS. USE MRC ABGL - WITH ISAC CODING FROM TABLE 0315. 2D AND 1B MODE REPLY21AA051AC20 BMXBJ 04HEIGHT ABOVE BASE,LINE,CENTER,HUB HUB CENTER LINE HEIGHT ABOVE BASE A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE HUB CENTER LINE ABOVE THE BASE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BMXFJ 10CAPACITY,TANK,LUBRICANT LUBRICANT TANK CAPACITY THE CAPACITY OF LUBRICANT THE TANK IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY12AG67 BMXGJ 10PRESSURE DEVELOPED,GREASE,MAXIMUM MAXIMUM GREASE PRESSURE DEVELOPED AN INDICATION OF THE MAXIMUM GREASE PRESSURE DEVELOPED. 1D AND 1B MODE REPLY12AG67 BMXHD /D/ 07HOSE,LUBRICANT LUBRICANT HOSE AN INDICATION OF WHETHER OR NOT A LUBRICANT HOSE IS INCLUDED. SELECT REPLY CODE 10AA49 BMXJD 18TYPE,ELEMENT,ROLLING ROLLING ELEMENT TYPE INDICATES THE TYPE OF ROLLING ELEMENT(S) PROVIDED. SELECT REPLY CODE 10AA78 BMXKD /D/ 09MATERIAL,SPOUT SPOUT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH A SPOUT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BMXLD /D/ 17SURFACE TREATMENT,SPOUT SPOUT SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SPOUT SURFACE. SELECT REPLY CODE 10AD09 BMXMD /D/ 18TYPE,BACKING,PERMANENT PERMANENT BACKING TYPE INDICATES THE TYPE OF PERMANENT BACKING PROVIDED. SELECT REPLY CODE 10AF82 BMXND 18TYPE,BACKING,REMOVABLE REMOVABLE BACKING TYPE INDICATES THE TYPE OF REMOVABLE BACKING PROVIDED. SELECT REPLY CODE 10AF82 BMXPD 07PROVISION,THREAD,SPOUT BOTTOM END SPOUT BOTTOM END THREAD PROVISION AN INDICATION OF WHETHER OR NOT THE SPOUT BOTTOM END IS THREADED. SELECT REPLY CODE 10AE00 BMXQD /D/ 07CAP,CLOSURE,SPOUT SPOUT CLOSURE CAP AN INDICATION OF WHETHER OR NOT A SPOUT CLOSURE CAP IS INCLUDED. SELECT REPLY CODE 10AA49 BMXRD /D/ 07FEATURE,ATTACHMENT,CAP CAP ATTACHMENT FEATURE AN INDICATION OF WHETHER OR NOT A CAP ATTACHMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BMXSD /D/ 07LEVER,CONTROL,CHECK VALVE CHECK VALVE CONTROL LEVER AN INDICATION OF WHETHER OR NOT A CHECK VALVE CONTROL LEVER IS INCLUDED. SELECT REPLY CODE 10AA49 BMXTD /D/ 07BRACKET,HOLDER HOLDER BRACKET AN INDICATION OF WHETHER OR NOT A HOLDER BRACKET IS INCLUDED. SELECT REPLY CODE 10AA49 BMXWG 10CAPACITY,LUBRICANT LUBRICANT CAPACITY THE CAPACITY OF LUBRICANT AN ITEM IS DESIGNED TO HOLD. FULL TEXT WRITE-IN 0 BMXXJ T10RANGE,PRESSURE,AIR,OPERATING OPERATING AIR PRESSURE RANGE THE MINIMUM TO MAXIMUM VALUES OF AIR PRESSURE AT WHICH THE ITEM IS DESIGNED TO OPERATE. 1D AND 1F MODE REPLY12AJ20 BMXYG /D/ 19RATIO,DEVELOPED GREASE PRESSURE TO APPLIED AIR PRESSURE DEVELOPED GREASE PRESSURE TO APPLIED AIR PRESSURE RATIO AN INDICATION OF THE RATIO OF DEVELOPED GREASE PRESSURE TO APPLIED AIR PRESSURE. FULL TEXT WRITE-IN 0 BMXZA /D/ 13THREAD SIZE,CONNECTION,AIR HOSE AIR HOSE CONNECTION THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE THREADED AIR HOSE CONNECTION. 1A MODE REPLY 0 BMYBD 13THREAD SERIES,CONNECTION,AIR HOSE AIR HOSE CONNECTION THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF THE THREADED AIR HOSE CONNECTION. SELECT REPLY CODE 10AH06 BMYCG /D/ 19DIMENSION,CROSS-SECTIONAL,BARB BARB CROSS-SECTIONAL DIMENSION A MEASUREMENT OF THE PHYSICAL LIMITS OF THE BARB WHEN VIEWED IN CROSS SECTION. FULL TEXT WRITE-IN 0 BMYDA 12QUANTITY,POINT,BARB BARB POINT QUANTITY THE NUMBER OF POINT(S) PROVIDED ON THE BARB. 1A MODE REPLY 0 BMYFJ /D/ 04HEIGHT,FACE FACE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE FACE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BMYGJ /D/ 04DEPTH,FACE FACE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BMYHJ /D/ 04THICKNESS THROUGH BULKHEAD,FLANGE FLANGE THICKNESS THROUGH BULKHEAD NONE. 2D AND 1B MODE REPLY21AA051AC20 BMYJJ /D/ 04DIAMETER THROUGH BULKHEAD,FLANGE FLANGE DIAMETER THROUGH BULKHEAD NONE. 2D AND 1B MODE REPLY21AA051AC20 BMYKJ 04LENGTH,BEVEL BEVEL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BMYLJ /D/ 04HEIGHT,BEVEL BEVEL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BMYMD 01COLOR,CAP CAP COLOR THE HUE OR TINT OF THE CAP. SELECT REPLY CODE 10AD06 BMYNJ 04DISTANCE BETWEEN BARBS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN BARBS THE CENTER TO CENTER DISTANCE BETWEEN BARBS. 2D AND 1B MODE REPLY21AA051AC20 BMYPD 18TYPE,END,SPINDLE SPINDLE END TYPE INDICATES THE TYPE OF SPINDLE END ON THE ITEM. SELECT REPLY CODE 10AK95 BMYQJ /D/ 04LENGTH,SPINDLE,BUFFING/POLISHING WHEEL BUFFING/POLISHING WHEEL SPINDLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A BUFFING/POLISHING WHEEL SPINDLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BMYRJ 10SPEED IN RPM,SPINDLE SPINDLE SPEED IN RPM THE RATED SPEED/S/ OF THE SPINDLE,EXPRESSED IN REVOLUTIONS PER MINUTE. 1D AND 1B MODE REPLY11AC20 BMYSJ 04DIAMETER ACCOMMODATED,WHEEL,MAXIMUM MAXIMUM WHEEL DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE WHEEL,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BMYTJ 04THICKNESS ACCOMMODATED,WHEEL,MAXIMUM MAXIMUM WHEEL THICKNESS ACCOMMODATED THE MAXIMUM MEASUREMENT OF THE SMALLEST DIMENSION OF A WHEEL THE ITEM WILL ACCOMMODATE,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 BMYWD /D/ 02DESIGN,REST,WORK WORK REST DESIGN THE DESIGN OF WORK REST PROVIDED. SELECT REPLY CODE 10AK54 BMYXJ 10SWING,RATED,MAXIMUM MAXIMUM RATED SWING THE MAXIMUM RATED SWING OF THE ITEM. 1D AND 1B MODE REPLY11AA05 BMYYD /D/ 18TYPE,INSERT/ADDITIVE INSERT/ADDITIVE TYPE INDICATES THE TYPE OF INSERT AND/OR ADDITIVE PROVIDED. SELECT REPLY CODE 10AN41 BMYZJ 04DISTANCE BETWEEN HEAD STOCK AND TAIL STOCK CENTERS DISTANCE BETWEEN HEAD STOCK AND TAIL STOCK CENTERS THE DISTANCE BETWEEN HEAD STOCK AND TAIL STOCK CENTERS. 2D AND 1B MODE REPLY21AA051AC20 BMZAJ /D/ 10DENSITY,PRINTING,RESOLUTION RESOLUTION PRINTING DENSITY INDICATES THE NUMBER OF PRINTED DOTS THE ITEM CAN PRINT ON A RATED AREA. 2D AND 1B MODE REPLY22AB491AA99 BMZBG 04DIAMETER,FLARE,SECOND END SECOND END FLARE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SECOND END FLARE, AND TERMINATES AT THE CIRCUMFERENCE. FULL TEXT WRITE-IN 0 BNBBD 18TYPE,TABLE TABLE TYPE INDICATES THE TYPE OF TABLE PROVIDED. SELECT REPLY CODE 10AK54 BNBCJ 04DISTANCE BETWEEN TAIL STOCKS DISTANCE BETWEEN TAIL STOCKS THE DISTANCE BETWEEN THE TAIL STOCKS. 2D AND 1B MODE REPLY21AA051AC20 BNBDJ 10TRAVEL,LONGITUDINAL,TABLE TABLE LONGITUDINAL TRAVEL THE LONGITUDINAL DISTANCE THE TABLE WILL TRAVEL. 2D AND 1B MODE REPLY21AA051AC20 BNBFJ 10TRAVEL,CROSS,TABLE TABLE CROSS TRAVEL THE CROSS DISTANCE THE TABLE WILL TRAVEL. 2D AND 1B MODE REPLY21AA051AC20 BNBGB 10ADJUSTMENT IN DEG,SWIVEL,TABLE TABLE SWIVEL ADJUSTMENT IN DEG THE SWIVEL ADJUSTMENT OF THE TABLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BNBHB 10ADJUSTMENT IN DEG,TILT,TABLE TABLE TILT ADJUSTMENT IN DEG THE TILT ADJUSTMENT OF THE TABLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BNBJJ 10ADJUSTMENT,VERTICAL,TABLE TABLE VERTICAL ADJUSTMENT THE DISTANCE THE TABLE CAN BE ADJUSTED VERTICALLY. 2D AND 1B MODE REPLY21AA051AC20 BNBKD 18TYPE,HEAD,WHEEL WHEEL HEAD TYPE INDICATES THE TYPE OF WHEEL HEAD PROVIDED. SELECT REPLY CODE 10AK33 BNBLJ 10TRAVEL,HORIZONTAL,WHEEL HEAD WHEEL HEAD HORIZONTAL TRAVEL THE DISTANCE THE WHEEL HEAD WILL TRAVEL HORIZONTALLY. 2D AND 1B MODE REPLY21AA051AC20 BNBMH /D/ 09MATERIAL AND TYPE,SHUTTER SHUTTER MATERIAL AND TYPE THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHUTTER IS FABRICATED,AND THE TYPE. 2D MODE REPLY 26AD093AK54 BNBNG 19ADJUSTMENT,SWIVEL,WHEEL HEAD WHEEL HEAD SWIVEL ADJUSTMENT THE SWIVEL ADJUSTMENT OF THE WHEEL HEAD. FULL TEXT WRITE-IN 0 BNBPD /D/ 07FEATURE,TYPE,VACUUM VACUUM TYPE FEATURE AN INDICATION OF WHETHER OR NOT A VACUUM TYPE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BNBQJ 10ADJUSTMENT,VERTICAL,HEAD,WHEEL WHEEL HEAD VERTICAL ADJUSTMENT THE DISTANCE THE WHEEL HEAD CAN BE ADJUSTED VERTICALLY. 2D AND 1B MODE REPLY21AA051AC20 BNBRD /D/ 07NEEDLE,ATTACHED ATTACHED NEEDLE AN INDICATION OF WHETHER OR NOT AN ATTACHED NEEDLE IS INCLUDED. SELECT REPLY CODE 10AA49 BNBSD /D/ 07ANTICOAGULANT ANTICOAGULANT AN INDICATION OF WHETHER OR NOT AN ANTICOAGULANT IS INCLUDED. SELECT REPLY CODE 10AA49 BNBTD 19CHEMICAL,ANTICOAGULANT ANTICOAGULANT CHEMICAL THE SUBSTANCE USED AS AN ANTICOAGULANT AGENT. SELECT REPLY CODE 10AG54 BNBWJ 04DIAMETER,MAXIMUM,WHEEL WHEEL MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WHEEL,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BNBXJ 04DIAMETER AND TYPE,ATTACHMENT,WHEEL HEAD WHEEL HEAD ATTACHMENT DIAMETER AND TYPE THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A WHEEL HEAD ATTACHMENT,AND TERMINATES AT THE CIRCUMFERENCE,AND ITS TYPE. 3D AND 1B MODE REPLY31AA051AC202AG25 BNBYG 10ADJUSTMENT,SWIVEL,HEAD STOCK HEAD STOCK SWIVEL ADJUSTMENT THE SWIVEL ADJUSTMENT OF THE HEAD STOCK. FULL TEXT WRITE-IN 0 BNBZJ /D/ 04DISTANCE FROM WHEEL HEAD SPINDLE CENTER/FACE TO TABLE TOP,MAXIMUM MAXIMUM DISTANCE FROM WHEEL HEAD SPINDLE CENTER/FACE TO TABLE TOP THE MAXIMUM DISTANCE FROM THE CENTER OR FACE OF THE WHEEL HEAD SPINDLE TO THE TABLE TOP. 1D AND 1B MODE REPLY11AA05 BNCBD /D/ 09MATERIAL,MORTAR MORTAR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MORTAR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BNCCD 14SHAPE,CAVITY CAVITY SHAPE THE PHYSICAL CONFIGURATION OF THE CAVITY. SELECT REPLY CODE 10AD07 BNCDD /D/ 07MOUND,CENTER CENTER MOUND AN INDICATION OF WHETHER OR NOT A CENTER MOUND IS INCLUDED. SELECT REPLY CODE 10AA49 BNCFD /D/ 07FEATURE,POUR-OUT POUR-OUT FEATURE AN INDICATION OF WHETHER OR NOT A POUR-OUT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BNCGD 19CONSTRUCTION,PESTLE PESTLE CONSTRUCTION THE STRUCTURAL CHARACTERISTIC(S) OF THE PESTLE. SELECT REPLY CODE 10AL59 BNCHD /D/ 09MATERIAL,END,WORKING WORKING END MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WORKING END IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BNCJH /D/ 17SURFACE TREATMENT AND LOCATION SURFACE TREATMENT AND LOCATION THE PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE ITEM AND ITS LOCATION. 3D MODE REPLY 36AD093AJ912AH46 BNCKD 19CONDITION,SURFACE,GRINDING GRINDING SURFACE CONDITION THE CONDITION OF THE GRINDING SURFACE WITH RESPECT TO THE TEXTURE. SELECT REPLY CODE 10AK39 BNCLJ 04DIAMETER,OVERALL,BASE BASE OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF THE BASE. 2D AND 1B MODE REPLY21AA051AC20 BNCMD /D/ 07SLEEVE,PESTLE PESTLE SLEEVE AN INDICATION OF WHETHER OR NOT A PESTLE SLEEVE IS INCLUDED. SELECT REPLY CODE 10AA49 BNCNG 10CAPACITY,HOLDER HOLDER CAPACITY THE CAPACITY OF THE HOLDER. FULL TEXT WRITE-IN 0 BNCQD 07ADJUSTABILITY,POSITION,BURNER BURNER POSITION ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE BURNER POSITION IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BNCRD 19POSITION,ADJUSTMENT,BURNER BURNER ADJUSTMENT POSITION THE POSITION(S) TO WHICH THE BURNER CAN BE ADJUSTED. SELECT REPLY CODE 10AF63 BNCSD 19POSITION,FIXED,BURNER BURNER FIXED POSITION THE FIXED POSITION FOR WHICH THE BURNER IS DESIGNED. SELECT REPLY CODE 10AF63 BNCTA 12QUANTITY,TUBE,FEED FEED TUBE QUANTITY THE NUMBER OF FEED TUBE(S) PROVIDED. 1A MODE REPLY 0 BNCWD /D/ 02DESIGN,USAGE,FEED TUBE FEED TUBE USAGE DESIGN THE DESIGNED USE OF THE FEED TUBE. SELECT REPLY CODE 10AN61 BNCXD 18TYPE,CONTROL,FEED TUBE FEED TUBE CONTROL TYPE INDICATES THE TYPE OF DEVICE THAT CONTROLS THE FEED TUBE. SELECT REPLY CODE 10AK54 BNCYD 11METHOD,ADJUSTMENT,AIR SUPPLY AIR SUPPLY ADJUSTMENT METHOD THE MEANS USED TO ADJUST THE SUPPLY OF AIR. SELECT REPLY CODE 10AK54 BNCZD 18TYPE,TIP,BURNER BURNER TIP TYPE INDICATES THE TYPE OF BURNER TIP PROVIDED. SELECT REPLY CODE 10AJ55 BNDBD /D/ 07TIP,BURNER,REMOVABLE REMOVABLE BURNER TIP AN INDICATION OF WHETHER OR NOT A REMOVABLE BURNER TIP(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BNDCJ A18TYPE AND QUANTITY,HEAD HEAD TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF HEADS. 1D AND 1A MODE REPLY13AK54 BNDDJ 10HEATING RATE IN BTU HEATING RATE IN BTU THE RATE OF HEATING,EXPRESSED IN BRITISH THERMAL UNITS. 2D AND 1B MODE REPLY22AG551AC20 BNDFD /D/ 09MATERIAL,RESERVOIR RESERVOIR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE RESERVOIR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BNDGD 07REMOVABILITY,RESERVOIR RESERVOIR REMOVABILITY AN INDICATION OF WHETHER OR NOT THE RESERVOIR IS REMOVABLE. SELECT REPLY CODE 10AC29 BNDHD /D/ 07ATTACHMENT,LEVEL,WATER,CONSTANT CONSTANT WATER LEVEL ATTACHMENT AN INDICATION OF WHETHER OR NOT A CONSTANT WATER LEVEL ATTACHMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BNDJD /D/ 07CUTOFF,WATER,LOW LOW WATER CUTOFF AN INDICATION OF WHETHER OR NOT A LOW WATER CUTOFF IS INCLUDED. SELECT REPLY CODE 10AA49 BNDKD 01COLOR,SURFACE,INNER INNER SURFACE COLOR THE HUE OR TINT OF THE INNER SURFACE OF THE ITEM. SELECT REPLY CODE 10AD06 BNDLA 12QUANTITY,RING,NEST NEST RING QUANTITY THE NUMBER OF RING(S) IN THE NEST. 1A MODE REPLY 0 BNDMD /D/ 07RACK,TUBE,TEST TEST TUBE RACK AN INDICATION OF WHETHER OR NOT A TEST TUBE RACK IS INCLUDED. SELECT REPLY CODE 10AA49 BNDNJ 04DIAMETER,RECEPTACLE RECEPTACLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE RECEPTACLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BNDPJ 10FREQUENCY RATING,ELEMENT,HEATING HEATING ELEMENT FREQUENCY RATING THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE HEATING ELEMENT IS RATED. 2D AND 1B MODE REPLY21AC321AC20 BNDQD /D/ 07AGITATOR AGITATOR AN INDICATION OF WHETHER OR NOT AN AGITATOR IS INCLUDED. SELECT REPLY CODE 10AA49 BNDRD /D/ 07THERMOREGULATOR THERMOREGULATOR AN INDICATION OF WHETHER OR NOT A THERMOREGULATOR IS INCLUDED. SELECT REPLY CODE 10AA49 BNDSJ T10RANGE,ACCURACY ACCURACY RANGE THE RANGE OF ACCURACY FOR WHICH THE ITEM IS DESIGNED. 1D AND 1F MODE REPLY12AG67 BNDTG 19SETTINGS,REGULATING,TEMP TEMP REGULATING SETTINGS AN INDICATION OF THE TEMPERATURE REGULATING SETTINGS OF THE ITEM. FULL TEXT WRITE-IN 0 BNDWD /D/ 07COILS FOR BELOW ROOM TEMP USE,COOLING COOLING COILS FOR BELOW ROOM TEMP USE AN INDICATION OF WHETHER OR NOT COOLING COILS FOR BELOW ROOM TEMPERATURE USE ARE INCLUDED. SELECT REPLY CODE 10AA49 BNDXD /D/ 07OPENING,THERMOMETER THERMOMETER OPENING AN INDICATION OF WHETHER OR NOT A THERMOMETER OPENING IS PROVIDED. SELECT REPLY CODE 10AB22 BNDYD /D/ 07LIGHT,PILOT PILOT LIGHT AN INDICATION OF WHETHER OR NOT A PILOT LIGHT IS INCLUDED. SELECT REPLY CODE 10AA49 BNDZD /D/ 07CLOSURE,CAP,SAFETY SAFETY CAP CLOSURE AN INDICATION OF WHETHER OR NOT A SAFETY CAP CLOSURE IS PROVIDED. SELECT REPLY CODE 10AB22 BNFBD /D/ 07ADAPTER,SLEEVE SLEEVE ADAPTER AN INDICATION OF WHETHER OR NOT A SLEEVE ADAPTER IS INCLUDED. SELECT REPLY CODE 10AA49 BNFCD 18TYPE,DRIVE,OUTPUT SHAFT OUTPUT SHAFT DRIVE TYPE INDICATES THE TYPE OF DRIVE FOR TURNING,ROTATING,OR POSITIONING THE OUTPUT SHAFT. SELECT REPLY CODE 10AG25 BNFDA 10RATIO,REDUCTION REDUCTION RATIO THE MAXIMUM TO MINIMUM REDUCTION RATIO,WITH THE LARGER RELATIVE PROPORTION GIVEN,THE LOWER VALUE HAVING AN IMPLIED (NOT GIVEN) VALUE OF ONE (UNITY). 1A MODE REPLY 0 BNFFG /D/ 19POSITION,SHAFT,OUTPUT OUTPUT SHAFT POSITION THE POSITION OF THE OUTPUT SHAFT ON THE ITEM. FULL TEXT WRITE-IN 0 BNFGJ 04DIAMETER,SHAFT,OUTPUT OUTPUT SHAFT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTPUT SHAFT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNFHD /D/ 07CONTROL,SPEED,INTEGRAL INTEGRAL SPEED CONTROL AN INDICATION OF WHETHER OR NOT AN INTEGRAL SPEED CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 BNFJF T10RANGE IN RPM,CONTROL,SPEED SPEED CONTROL RANGE IN RPM THE MINIMUM AND MAXIMUM SPEED CONTROL LIMITS, EXPRESSED IN REVOLUTIONS PER MINUTE. 1F MODE REPLY 0 BNFKJ 04DIAMETER,MAXIMUM,ACCOMMODATED STIRRING ROD ACCOMMODATED STIRRING ROD MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED STIRRING ROD,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BNFLD 05DIRECTION,ADJUSTMENT ADJUSTMENT DIRECTION THE DIRECTION IN WHICH THE ITEM IS ADJUSTABLE. SELECT REPLY CODE 10AF63 BNFMD /D/ 07CORD,EXTENSION,ATTACHED ATTACHED EXTENSION CORD AN INDICATION OF WHETHER OR NOT AN ATTACHED EXTENSION CORD IS INCLUDED. SELECT REPLY CODE 10AA49 BNFND /D/ 07FEATURE,ADJUSTMENT,STIRRING POSITION STIRRING POSITION ADJUSTMENT FEATURE AN INDICATION OF WHETHER OR NOT A STIRRING POSITION ADJUSTMENT FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BNFPJ 04WIDTH,OVERALL,BASE BASE OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BASE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BNFQJ 04LENGTH,OVERALL,LEG LEG OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE LEG. 2D AND 1B MODE REPLY21AA051AC20 BNFRD /D/ 09MATERIAL,ROD,SUPPORT SUPPORT ROD MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SUPPORT ROD IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BNFSD /D/ 17SURFACE TREATMENT,ROD,SUPPORT SUPPORT ROD SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SUPPORT ROD SURFACE. SELECT REPLY CODE 10AD09 BNFTD 07DETACHABILITY,ROD,SUPPORT SUPPORT ROD DETACHABILITY AN INDICATION OF WHETHER OR NOT THE SUPPORT ROD IS DETACHABLE. SELECT REPLY CODE 10AH97 BNFWG 08LOCATION,ROD,SUPPORT SUPPORT ROD LOCATION INDICATES THE LOCATION OF THE SUPPORT ROD ON THE ITEM. FULL TEXT WRITE-IN 0 BNFXA 12QUANTITY,WELL WELL QUANTITY THE NUMBER OF WELL(S) PROVIDED. 1A MODE REPLY 0 BNFYJ 04LENGTH,INSIDE,TRIANGLE SIDE TRIANGLE SIDE INSIDE LENGTH A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF THE TRIANGLE SIDE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BNFZD 14SHAPE,CROSS-SECTIONAL,WIRE WIRE CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE WIRE WHEN VIEWED IN CROSS-SECTION. SELECT REPLY CODE 10AD07 BNGBD /D/ 09MATERIAL,PATCH,CENTER CENTER PATCH MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CENTER PATCH IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BNGCJ 04DIAMETER,PATCH,CENTER CENTER PATCH DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CENTER PATCH,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNGDJ A10COUNT,MESH MESH COUNT THE NUMBER OF OPEN SPACES BETWEEN THE YARNS PER MEASUREMENT SCALE. 1D AND 1A MODE REPLY11AB39 BNGFD 11METHOD,ADJUSTMENT,JAW ARMS JAW ARMS ADJUSTMENT METHOD THE MEANS USED TO ADJUST THE JAW ARMS. SELECT REPLY CODE 10AL28 BNGGJ 04DIAMETER,CLAMPING,MAXIMUM MAXIMUM CLAMPING DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CLAMPING FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BNGHD /D/ 07JAW,SWIVEL SWIVEL JAW AN INDICATION OF WHETHER OR NOT A SWIVEL JAW IS PROVIDED. SELECT REPLY CODE 10AB22 BNGJD /D/ 07PROVISION,ATTACHMENT,INTEGRAL INTEGRAL ATTACHMENT PROVISION AN INDICATION OF WHETHER OR NOT A MEANS IS PROVIDED FOR INTEGRAL ATTACHMENT. SELECT REPLY CODE 10AB22 BNGKD /D/ 08LOCATION,FACILITY,ATTACHMENT ATTACHMENT FACILITY LOCATION INDICATES THE LOCATION OF AN ITEM WHICH HAS THE ATTACHMENT FACILITY. SELECT REPLY CODE 10AJ91 BNGLJ 04DIAMETER,CLAMPING,MAXIMUM,ROD ROD MAXIMUM CLAMPING DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CLAMPING FOR WHICH THE ROD IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BNGMJ 04LENGTH,BLADE,SECOND SECOND BLADE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BNGNJ 04WIDTH,BLADE,SECOND SECOND BLADE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BNGPJ 04LENGTH,SPOON SPOON LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BNGQJ 04WIDTH,SPOON SPOON WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BNGRJ 10RANGE,FREQUENCY FREQUENCY RANGE THE MINIMUM AND MAXIMUM CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH AN ITEM IS RATED. 2D AND 1B MODE REPLY21AC321AC20 BNGSA 12QUANTITY,COIL,INNERSPRING INNERSPRING COIL QUANTITY THE NUMBER OF INNERSPRING COILS PROVIDED. 1A MODE REPLY 0 BNGTD 11METHOD,DETERMINATION,THRESHOLD ODOR INTENSITY THRESHOLD ODOR INTENSITY DETERMINATION METHOD THE MEANS USED TO DETERMINE THE THRESHOLD ODOR INTENSITY. SELECT REPLY CODE 10AF11 BNGWD /D/ 07VALVE,DILUTION,THRESHOLD THRESHOLD DILUTION VALVE AN INDICATION OF WHETHER OR NOT A THRESHOLD DILUTION VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 BNGXD /D/ 07TABLETS,REAGENT REAGENT TABLETS AN INDICATION OF WHETHER OR NOT REAGENT TABLETS ARE INCLUDED. SELECT REPLY CODE 10AA49 BNGYB /D/ 10PERCENT,CONCENTRATION,SOLUTION SOLUTION CONCENTRATION PERCENT THE PERCENT OF SOLUTION CONCENTRATION. 1B MODE REPLY 0 BNGZJ /D/ 10VOLUME,SOLUTION SOLUTION VOLUME THE UNIT OF VOLUME FOR WHICH THE SOLUTION IS RATED. 1D AND 1B MODE REPLY12AG67 BNHBJ /D/ 10CALIBRATION,TUBE,COMPARISON COMPARISON TUBE CALIBRATION THE CALIBRATION FOR WHICH THE COMPARISON TUBE(S) IS DESIGNED. 1D AND 1B MODE REPLY12AG67 BNHCD 18TYPE,CHEMICAL CHEMICAL TYPE INDICATES THE TYPE OF CHEMICAL PROVIDED. SELECT REPLY CODE 10AG54 BNHDA 12QUANTITY,BOTTLE BOTTLE QUANTITY THE NUMBER OF BOTTLES PROVIDED. 1A MODE REPLY 0 BNHFJ /D/ 10YIELD,SOLUTION,CONCENTRATE CONCENTRATE SOLUTION YIELD THE AMOUNT OF SOLUTION A SPECIFIED MEASURE OF CONCENTRATE WILL MAKE. 2D AND 1B MODE REPLY22AG672AE96 BNHGD /D/ 07LABEL,BOTTLE BOTTLE LABEL AN INDICATION OF WHETHER OR NOT A BOTTLE LABEL IS PROVIDED. SELECT REPLY CODE 10AB22 BNHHG /D/ 19CHEMICAL,FURNISHED FURNISHED CHEMICAL THE CHEMICAL(S) FURNISHED IN THE ITEM. FULL TEXT WRITE-IN 0 BNHJJ 04SIZE,ORIFICE,VALVE VALVE ORIFICE SIZE DESIGNATES THE SIZE OF THE VALVE ORIFICE. 1D AND 1B MODE REPLY11AA05 BNHKJ 10CAPACITY,DEPTH,SOIL SOIL DEPTH CAPACITY THE CAPACITY OF THE SOIL DEPTH OF THE ITEM. 1D AND 1B MODE REPLY11AA05 BNHLD /D/ 07FEATURE,ESCAPEMENT,STEAM STEAM ESCAPEMENT FEATURE AN INDICATION OF WHETHER OR NOT A STEAM ESCAPEMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BNHMJ 04DIAMETER,RING,LARGEST LARGEST RING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST RING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNHND /D/ 07SOURCE,HEAT,INTEGRAL INTEGRAL HEAT SOURCE AN INDICATION OF WHETHER OR NOT AN INTEGRAL HEAT SOURCE IS INCLUDED. SELECT REPLY CODE 10AA49 BNHPD /D/ 07BURNER BURNER AN INDICATION OF WHETHER OR NOT A BURNER IS INCLUDED. SELECT REPLY CODE 10AA49 BNHQJ 04HEIGHT,LEG LEG HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE LEG,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BNHRD /D/ 09MATERIAL,TRIPOD TRIPOD MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TRIPOD IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BNHSD /D/ 07SHIELD,FLAME FLAME SHIELD AN INDICATION OF WHETHER OR NOT A FLAME SHIELD IS INCLUDED. SELECT REPLY CODE 10AA49 BNHTD 07DETACHABILITY,SHIELD SHIELD DETACHABILITY AN INDICATION OF WHETHER OR NOT THE SHIELD IS DETACHABLE. SELECT REPLY CODE 10AH97 BNHWA 12QUANTITY FOR WHICH DESIGNED,PIPETTE PIPETTE QUANTITY FOR WHICH DESIGNED THE NUMBER OF PIPETTE(S) FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 BNHXD 19LIQUID,INDICATING,OPERATING TEMP OPERATING TEMP INDICATING LIQUID THE LIQUID USED TO INDICATE THE OPERATING TEMPERATURE OF THE ITEM. SELECT REPLY CODE 10AB75 BNHYD /D/ 07CONTROL,TEMP,CONSTANT CONSTANT TEMP CONTROL AN INDICATION OF WHETHER OR NOT A CONSTANT TEMPERATURE CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 BNHZJ 10ACCURACY RATING ACCURACY RATING AN INDICATION OF THE ACCURACY OF AN ITEM. 1D AND 1B MODE REPLY13AJ40 BNJBD /D/ 07CIRCULATOR,LIQUID LIQUID CIRCULATOR AN INDICATION OF WHETHER OR NOT A LIQUID CIRCULATOR IS INCLUDED. SELECT REPLY CODE 10AA49 BNJCA 12QUANTITY ACCOMMODATED,JAR,TEST TEST JAR QUANTITY ACCOMMODATED THE NUMBER OF TEST JAR(S) THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 BNJDD 08LOCATION,INSULATION INSULATION LOCATION INDICATES THE LOCATION OF AN ITEM WHICH IS INSULATED. SELECT REPLY CODE 10AJ91 BNJFA 12QUANTITY,UNIT,TEST TEST UNIT QUANTITY THE NUMBER OF TEST UNITS PROVIDED. 1A MODE REPLY 0 BNJGJ 10TEMP RATING,CALIBRATED CALIBRATED TEMP RATING THE RATED DEGREE OF TEMPERATURE AT WHICH CALIBRATED. 1D AND 1B MODE REPLY13AJ40 BNJHF T10RANGE,SECONDS,SAYBOLT SAYBOLT SECONDS RANGE THE MINIMUUM AND MAXIMUM LIMITS,EXPRESSED IN SAYBOLT SECONDS,AT WHICH THE VISCOSITY OF FLUID/S/ IS MEASURED. 1F MODE REPLY 0 BNJJD /D/ 07SPACE FOR MARKING,SANDBLASTED SANDBLASTED SPACE FOR MARKING AN INDICATION OF WHETHER OR NOT A SANDBLASTED SPACE FOR MARKING IS INCLUDED. SELECT REPLY CODE 10AA49 BNJKA 12QUANTITY,TUBE,SAMPLING SAMPLING TUBE QUANTITY THE NUMBER OF SAMPLING TUBE(S) PROVIDED. 1A MODE REPLY 0 BNJLJ 04LENGTH,OVERALL,TUBE TUBE OVERALL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TUBE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BNJMJ 10FLOW RATE,SAMPLE SAMPLE FLOW RATE THE RATED SAMPLE FLOW OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BNJND /D/ 07STAND,TELESCOPIC,SAMPLING TUBE SAMPLING TUBE TELESCOPIC STAND AN INDICATION OF WHETHER OR NOT A TELESCOPIC STAND FOR THE SAMPLING TUBE IS INCLUDED. SELECT REPLY CODE 10AA49 BNJPA /D/ 12QUANTITY,ELECTRODE ELECTRODE QUANTITY THE NUMBER OF ELECTRODE(S) PROVIDED. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 1A MODE REPLY 0 BNJQD /D/ 07GUARD,DUST,FALLING FALLING DUST GUARD AN INDICATION OF WHETHER OR NOT A FALLING DUST GUARD IS INCLUDED. SELECT REPLY CODE 10AA49 BNJRD /D/ 07HOLSTER,FLASK FLASK HOLSTER AN INDICATION OF WHETHER OR NOT A FLASK HOLSTER IS INCLUDED. SELECT REPLY CODE 10AA49 BNJSA /D/ 12QUANTITY,FLASK FLASK QUANTITY THE NUMBER OF FLASK(S) PROVIDED. 1A MODE REPLY 0 BNJTD 19CONSTRUCTION,BASE BASE CONSTRUCTION THE STRUCTURAL CHARACTERISTIC(S) OF THE BASE. SELECT REPLY CODE 10AL59 BNJWD /D/ 07STOPPER,NOZZLE NOZZLE STOPPER AN INDICATION OF WHETHER OR NOT A NOZZLE STOPPER(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BNJXD /D/ 07STOPPER,ARM,SIDE SIDE ARM STOPPER AN INDICATION OF WHETHER OR NOT A SIDE ARM STOPPER(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BNJYD /D/ 07STRAP,SHOULDER,CASE CASE SHOULDER STRAP AN INDICATION OF WHETHER OR NOT A CASE SHOULDER STRAP IS INCLUDED. SELECT REPLY CODE 10AA49 BNJZJ 04HEIGHT,OVERALL,CASE CASE OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE CASE. 2D AND 1B MODE REPLY21AA051AC20 BNKBD /D/ 07TUBE,EXTENSION EXTENSION TUBE AN INDICATION OF WHETHER OR NOT AN EXTENSION TUBE IS INCLUDED. SELECT REPLY CODE 10AA49 BNKCD /D/ 07GAGE GAGE AN INDICATION OF WHETHER OR NOT A GAGE IS INCLUDED. SELECT REPLY CODE 10AA49 BNKDF T10RANGE IN PERCENT,DETECTION DETECTION RANGE IN PERCENT THE MINIMUM AND MAXIMUM VALUES REPRESENTING THE DETECTION RATE OF THE ITEM,EXPRESSED IN PERCENT. 1F MODE REPLY 0 BNKFD 18TYPE,CELL,ANALYSIS ANALYSIS CELL TYPE INDICATES THE TYPE OF ANALYSIS CELL PROVIDED. SELECT REPLY CODE 10AK54 BNKGJ 04DIAMETER,LARGEST,END END LARGEST DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BNKHD 18TYPE,SAMPLE SAMPLE TYPE INDICATES THE TYPE OF SAMPLE PROVIDED. SELECT REPLY CODE 10AH00 BNKJJ 10TIME,RESPONSE RESPONSE TIME THE TIME REQUIRED FOR AN ITEM TO RESPOND TO A SPECIFIC CONDITION. 1D AND 1B MODE REPLY12AH68 BNKKF /D/T10RANGE IN PPM BY WEIGHT,METER METER RANGE IN PPM BY WEIGHT THE MINIMUM AND MAXIMUM LIMITS OF THE METER FOR WHICH THE ITEM IS RATED,EXPRESSED IN PARTS PER MILLION BY WEIGHT. 1F MODE REPLY 0 BNKLD 19REFERENCE,RADIATION RADIATION REFERENCE AN INDICATION OF THE RADIATION REFERENCE. SELECT REPLY CODE 10AK54 BNKMD 18TYPE EMITTED,RADIATION RADIATION TYPE EMITTED INDICATES THE TYPE OF RADIATION EMITTED. SELECT REPLY CODE 10AJ18 BNKND 09MATERIAL,RADIOACTIVE RADIOACTIVE MATERIAL INDICATES THE TYPE OF RADIOACTIVE MATERIAL. SELECT REPLY CODE 10AN41 BNKPG /D/ 19ACTIVITY,NOMINAL NOMINAL ACTIVITY THE NOMINAL AMOUNT OF ACTIVITY BY THE ITEM. FULL TEXT WRITE-IN 0 BNKQJ 10MAGNITUDE RATING,RADIOACTIVE RADIOACTIVE MAGNITUDE RATING AN INDICATION OF THE RADIOACTIVE MAGNITUDE REQUIRED FOR A GIVEN REACTION. 1D AND 1B MODE REPLY12AJ20 BNKRB 10HALF-LIFE IN YEARS HALF-LIFE IN YEARS THE PERIOD OF TIME IN WHICH THE ITEM FALLS TO HALF OF ITS ORIGINAL VALUE,EXPRESSED IN YEARS. 1B MODE REPLY 0 BNKSG /D/ 18TYPE,DETERMINATION DETERMINATION TYPE INDICATES THE TYPE OF DETERMINATION FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 BNKTG /D/ 10ACCURACY RATING ACCURACY RATING AN INDICATION OF THE RATED ACCURACY OF THE ITEM. FULL TEXT WRITE-IN 0 BNKWD /D/ 19SOLUTION,TESTED TESTED SOLUTION AN INDICATION OF THE SOLUTION TESTED BY THE ITEM. SELECT REPLY CODE 10AK54 BNKXD 18TYPE FOR WHICH DESIGNED,SPRING SPRING TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF SPRING(S) FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BNKYD /D/ 07FEATURE,USAGE,TORQUE INDICATING WRENCH TORQUE INDICATING WRENCH USAGE FEATURE AN INDICATION OF WHETHER OR NOT A TORQUE INDICATING WRENCH USAGE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BNKZD /D/ 07WRENCH,INDICATING,TORQUE TORQUE INDICATING WRENCH AN INDICATION OF WHETHER OR NOT A TORQUE INDICATING WRENCH IS INCLUDED. SELECT REPLY CODE 10AA49 BNLBD /D/ 07GAGE,TRAVEL,SPRING SPRING TRAVEL GAGE AN INDICATION OF WHETHER OR NOT A SPRING TRAVEL GAGE IS INCLUDED. SELECT REPLY CODE 10AA49 BNLCJ 04DIAMETER ACCOMMODATED,OUTSIDE,MAXIMUM,SPRING SPRING MAXIMUM OUTSIDE DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE SPRING,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BNLDJ 04LENGTH ACCOMMODATED,FREE,OVERALL,MAXIMUM,SPRING SPRING MAXIMUM OVERALL FREE LENGTH ACCOMMODATED THE MAXIMUM FREE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE SPRING THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BNLFJ 04LENGTH,OVERALL,TRAILER TRAILER OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE TRAILER. 2D AND 1B MODE REPLY21AA051AC20 BNLGJ 04WIDTH,OVERALL,TRAILER TRAILER OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TRAILER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BNLHJ 04HEIGHT,OVERALL,TRAILER TRAILER OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE TRAILER. 2D AND 1B MODE REPLY21AA051AC20 BNLJD /D/ 07COMPARTMENT COMPARTMENT AN INDICATION OF WHETHER OR NOT A COMPARTMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BNLKG 04SIZE,SHANK,POINT POINT SHANK SIZE DESIGNATES THE SIZE BY WHICH THE POINT SHANK IS IDENTIFIED. FULL TEXT WRITE-IN 0 BNLLJ 04DIAMETER,MAXIMUM,POINT POINT MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE POINT,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BNLMD 14SHAPE,RESERVOIR RESERVOIR SHAPE THE PHYSICAL CONFIGURATION OF THE RESERVOIR. SELECT REPLY CODE 10AD07 BNLNJ 04LENGTH,OVERALL,CASE CASE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CASE. 2D AND 1B MODE REPLY21AA051AC20 BNLPJ 04WIDTH,OVERALL,CASE CASE OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A CASE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BNLQJ 04DIAMETER,OUTSIDE,CYLINDER CYLINDER OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CYLINDER,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNLRJ /D/ 10CAPACITY,FLASK FLASK CAPACITY THE CAPACITY OF A FLASK. 1D AND 1B MODE REPLY12AG67 BNLSJ 04LENGTH,RESERVOIR RESERVOIR LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A RESERVOIR,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BNLTJ 04DIAMETER,RESERVOIR RESERVOIR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A RESERVOIR,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNLWJ 04WIDTH,RESERVOIR RESERVOIR WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A RESERVOIR,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BNLXJ 04DEPTH,RESERVOIR RESERVOIR DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE RESERVOIR,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BNLYJ /D/ 04LENGTH,INSIDE,RESERVOIR RESERVOIR INSIDE LENGTH A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF THE RESERVOIR,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BNLZJ 04DIAMETER,INSIDE,RESERVOIR RESERVOIR INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE RESERVOIR,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNMBJ /D/ 04WIDTH,INSIDE,RESERVOIR RESERVOIR INSIDE WIDTH AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE RESERVOIR,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BNMCJ 04DEPTH,INSIDE,RESERVOIR RESERVOIR INSIDE DEPTH A MEASUREMENT BETWEEN SPECIFIED INSIDE POINTS ON THE RESERVOIR,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BNMDD /D/ 07COVER,RESERVOIR RESERVOIR COVER AN INDICATION OF WHETHER OR NOT A RESERVOIR COVER IS PROVIDED. SELECT REPLY CODE 10AB22 BNMFD 02DESIGN,PIPETTE,ACCOMMODATED ACCOMMODATED PIPETTE DESIGN THE DESIGN OF THE PIPETTE(S) ACCOMMODATED. SELECT REPLY CODE 10AJ50 BNMGJ A19NAME AND QUANTITY ACCOMMODATED,COMPONENT COMPONENT NAME AND QUANTITY ACCOMMODATED THE NAME AND NUMBER OF COMPONENTS THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1A MODE REPLY13AL83 BNMHJ 04SIZE ACCOMMODATED,DISK,FILTER FILTER DISK SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE FILTER DISK ACCOMMODATED. 1D AND 1B MODE REPLY11AA05 BNMJA /D/ 12QUANTITY ACCOMMODATED,RECEPTACLE,CELL CELL RECEPTACLE QUANTITY ACCOMMODATED THE NUMBER OF CELL RECEPTACLE(S) ACCOMMODATED BY THE ITEM. 1A MODE REPLY 0 BNMKD /D/ 07GUIDELINE GUIDELINE AN INDICATION OF WHETHER OR NOT A GUIDELINE IS INCLUDED. SELECT REPLY CODE 10AA49 BNMLG 04SIZE ACCOMMODATED,BURETTE BURETTE SIZE ACCOMMODATED DESIGNATES THE SIZE OF BURETTE ACCOMMODATED. FULL TEXT WRITE-IN 0 BNMMD /D/ 07ROD/CLAMP,EXTENSION EXTENSION ROD/CLAMP AN INDICATION OF WHETHER OR NOT AN EXTENSION ROD AND CLAMP ARE INCLUDED. SELECT REPLY CODE 10AA49 BNMNA 12QUANTITY,TAB,PROJECTING PROJECTING TAB QUANTITY THE NUMBER OF PROJECTING TABS ON THE ITEM. 1A MODE REPLY 0 BNMPJ /D/ 04WIDTH,TROUGH TROUGH WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TROUGH,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BNMQJ /D/ 04DEPTH,TROUGH TROUGH DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE TROUGH,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BNMRD /D/ 09MATERIAL,FILLER,TROUGH TROUGH FILLER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF THE TROUGH FILLER MATERIAL. SELECT REPLY CODE 10AF45 BNMSD /D/ 07ROD,LOCKING LOCKING ROD AN INDICATION OF WHETHER OR NOT A LOCKING ROD IS INCLUDED. SELECT REPLY CODE 10AA49 BNMTD /D/ 07HANDLE,TRAY TRAY HANDLE AN INDICATION OF WHETHER OR NOT THE ITEM IS FURNISHED WITH A TRAY HANDLE. SELECT REPLY CODE 10AA55 BNMWJ 04LENGTH,OVERALL,TRAY TRAY OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE TRAY. 2D AND 1B MODE REPLY21AA051AC20 BNMXJ 04WIDTH,OVERALL,TRAY TRAY OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TRAY,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BNMYJ 04DEPTH,OVERALL,TRAY TRAY OVERALL DEPTH AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF THE TRAY,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BNMZA 12QUANTITY,RACK,INSERT INSERT RACK QUANTITY THE NUMBER OF INSERT RACKS IN THE ITEM. 1A MODE REPLY 0 BNNBJ 04LENGTH,OVERALL,INSERT RACK INSERT RACK OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE INSERT RACK. 1D AND 1B MODE REPLY11AA05 BNNCJ 04WIDTH,OVERALL,INSERT RACK INSERT RACK OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE INSERT RACK,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BNNDJ 04DEPTH,OVERALL,RACK,INSERT INSERT RACK OVERALL DEPTH AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF THE INSERT RACK,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 BNNFJ 04LENGTH ACCOMMODATED,SLIDE SLIDE LENGTH ACCOMMODATED A MEASUREMENT OF THE LONGEST DIMENSION OF THE SLIDE THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BNNGJ 04WIDTH ACCOMMODATED,SLIDE SLIDE WIDTH ACCOMMODATED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SLIDE THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BNNHJ /D/ 04DISTANCE FROM COVER BOTTOM TO HANDLE DISTANCE FROM COVER BOTTOM TO HANDLE THE DISTANCE FROM THE BOTTOM OF THE COVER TO THE HANDLE. 2D AND 1B MODE REPLY21AA051AC20 BNNJD /D/ 07ENDS,PERFORATED PERFORATED ENDS AN INDICATION OF WHETHER OR NOT PERFORATED ENDS ARE INCLUDED. SELECT REPLY CODE 10AA49 BNNKJ T04SIZE,SHELF SHELF SIZE DESIGNATES THE SIZE OF THE SHELF SURFACE(S) OF AN ITEM. 1D AND 1F MODE REPLY12AG67 BNNLA 12QUANTITY ACCOMMODATED,BOTTLE BOTTLE QUANTITY ACCOMMODATED THE NUMBER OF BOTTLES THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 BNNMD 18TYPE,CONTAINER,ICE ICE CONTAINER TYPE INDICATES THE TYPE OF ICE CONTAINER PROVIDED. SELECT REPLY CODE 10AE96 BNNNA 12QUANTITY,CONTAINER,ICE ICE CONTAINER QUANTITY THE NUMBER OF ICE CONTAINERS PROVIDED. 1A MODE REPLY 0 BNNPJ 10WEIGHT ACCOMMODATED,ICE ICE WEIGHT ACCOMMODATED THE WEIGHT OF THE ICE THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY12AG67 BNNQD /D/ 07GRIP,FINGER FINGER GRIP AN INDICATION OF WHETHER OR NOT A FINGER GRIP IS INCLUDED. SELECT REPLY CODE 10AA49 BNNRJ 04SIZE,MAXIMUM,JAW OPENING JAW OPENING MAXIMUM SIZE DESIGNATES THE MAXIMUM SIZE OF THE JAW OPENING. 1D AND 1B MODE REPLY11AA05 BNNSD /D/ 09MATERIAL,CHUCK CHUCK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CHUCK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BNNTD /D/ 17SURFACE TREATMENT,CHUCK CHUCK SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE CHUCK SURFACE. SELECT REPLY CODE 10AD09 BNNWD 14SHAPE,NEEDLE NEEDLE SHAPE THE PHYSICAL CONFIGURATION OF THE NEEDLE. SELECT REPLY CODE 10AD07 BNNXG 04SIZE ACCOMMODATED,JOINT,SPHERICAL SPHERICAL JOINT SIZE ACCOMMODATED DESIGNATES THE SIZE OF SPHERICAL JOINT THE ITEM IS DESIGNED TO ACCOMMODATE. FULL TEXT WRITE-IN 0 BNNYJ 04SIZE,MINIMUM,JAW FORK OPENING JAW FORK OPENING MINIMUM SIZE DESIGNATES THE MINIMUM SIZE OF THE JAW FORK OPENING. 1D AND 1B MODE REPLY11AA05 BNNZD /D/ 07DEVICE,LOCKING,SCREW SCREW LOCKING DEVICE AN INDICATION OF WHETHER OR NOT A SCREW LOCKING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 BNPBD /D/ 07BOTTOM,PERFORATED PERFORATED BOTTOM AN INDICATION OF WHETHER OR NOT A PERFORATED BOTTOM IS INCLUDED. SELECT REPLY CODE 10AA49 BNPCD /D/ 07SIDES,PERFORATED PERFORATED SIDES AN INDICATION OF WHETHER OR NOT PERFORATED SIDES ARE INCLUDED. SELECT REPLY CODE 10AA49 BNPDA 19NUMBER,GAGE,VENIPUNCTURE NEEDLE VENIPUNCTURE NEEDLE GAGE NUMBER THE MEASUREMENT OF THE DIAMETER OF THE VENIPUNCTURE NEEDLE SHAFT,AS DETERMINED BY THE UNIVERSAL STANDARD STUBS WIRE GAGE METHOD. 1A MODE REPLY 0 BNPFJ 04LENGTH,NEEDLE,VENIPUNCTURE VENIPUNCTURE NEEDLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE VENIPUNCTURE NEEDLE. 2D AND 1B MODE REPLY21AA051AC20 BNPGA /D/ 19NUMBER,GAGE,RUBBER STOPPER PUNCTURE NEEDLE RUBBER STOPPER PUNCTURE NEEDLE GAGE NUMBER THE MEASUREMENT OF THE DIAMETER OF THE RUBBER STOPPER PUNCTURE NEEDLE SHAFT,AS DETERMINED BY THE UNIVERSAL STANDARD STUBS WIRE GAGE METHOD. 1A MODE REPLY 0 BNPHJ /D/ 04LENGTH,NEEDLE,RUBBER STOPPER PUNCTURE RUBBER STOPPER PUNCTURE NEEDLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE RUBBER STOPPER PUNCTURE NEEDLE. 2D AND 1B MODE REPLY21AA051AC20 BNPJJ 04DIAMETER,FACILITY,FIRST END FIRST END FACILITY DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FACILITY ON THE FIRST END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNPKJ 04DIAMETER,FACILITY,SECOND END SECOND END FACILITY DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FACILITY ON THE SECOND END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNPLJ 04DIAMETER,INSIDE,CONNECTION CONNECTION INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO SURFACES OF A CIRCULAR CONNECTION,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNPMD /D/ 07HOUSING,GAP GAP HOUSING AN INDICATION OF WHETHER OR NOT A GAP HOUSING IS INCLUDED. SELECT REPLY CODE 10AA49 BNPNJ 04DEPTH,GAP GAP DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE GAP,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BNPPA 03DESIGNATOR,GAGE,METAL METAL GAGE DESIGNATOR THE DESIGNATOR FOR THE GAGE OF THE METAL. 1A MODE REPLY 0 BNPQJ 04THICKNESS,METAL METAL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE METAL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BNPRJ 04WIDTH,BED BED WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BED,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BNPSJ 10GAGE,BACK BACK GAGE THE AMOUNT OF WORK CLEARANCE AT THE REAR OF THE ITEM. 1D AND 1B MODE REPLY11AA05 BNPTJ 10GAGE,FRONT FRONT GAGE THE AMOUNT OF WORK CLEARANCE AT THE FRONT OF THE ITEM. 1D AND 1B MODE REPLY11AA05 BNPWA 12QUANTITY,STATION,DIE DIE STATION QUANTITY THE NUMBER OF DIE STATIONS PROVIDED. 1A MODE REPLY 0 BNPXJ 04DEPTH TO FRAME,THROAT THROAT DEPTH TO FRAME A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE THROAT TO THE FRAME,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BNPYJ 04DEPTH TO GAGE,THROAT THROAT DEPTH TO GAGE A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE THROAT TO THE GAGE,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BNPZG 12QUANTITY AND SIZE,PUNCH PUNCH QUANTITY AND SIZE THE NUMBER AND SIZE OF PUNCHES INCLUDED. FULL TEXT WRITE-IN 0 BNQBG /D/ 12QUANTITY AND SIZE,DIE DIE QUANTITY AND SIZE THE NUMBER AND SIZE OF DIES INCLUDED. FULL TEXT WRITE-IN 0 BNQCJ A04SIZE,TAPER,SPINDLE SPINDLE TAPER SIZE DESIGNATES THE COMMERCIAL TAPER SIZE OF THE SPINDLE. 1D AND 1A MODE REPLY12AH09 BNQDJ 04DIAMETER,QUILL,SPINDLE SPINDLE QUILL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CIRCULAR SPINDLE QUILL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNQFJ 04DISTANCE IN HEAD,TRAVEL,SPINDLE QUILL SPINDLE QUILL TRAVEL DISTANCE IN HEAD THE DISTANCE THE SPINDLE QUILL WILL TRAVEL IN THE HEAD. 2D AND 1B MODE REPLY21AA051AC20 BNQGJ 04DISTANCE ON COLUMN,TRAVEL,HEAD HEAD TRAVEL DISTANCE ON COLUMN THE DISTANCE THE HEAD WILL TRAVEL ON THE COLUMN. 2D AND 1B MODE REPLY21AA051AC20 BNQHJ 04DISTANCE FROM SPINDLE END TO TABLE TOP,MAXIMUM MAXIMUM DISTANCE FROM SPINDLE END TO TABLE TOP THE MAXIMUM DISTANCE FROM THE END OF THE SPINDLE TO THE TOP OF THE TABLE. 1D AND 1B MODE REPLY11AA05 BNQJD /D/ 07MATERIAL,BLENDED BLENDED MATERIAL AN INDICATION OF WHETHER OR NOT BLENDED MATERIAL IS INCLUDED. SELECT REPLY CODE 10AA49 BNQKJ 04DISTANCE FROM SPINDLE CENTER TO COLUMN NECK DISTANCE FROM SPINDLE CENTER TO COLUMN NECK THE DISTANCE FROM THE CENTER OF THE SPINDLE TO THE NECK OF THE COLUMN. 2D AND 1B MODE REPLY21AA051AC20 BNQLD 18TYPE,DRIVE,MAIN MAIN DRIVE TYPE INDICATES THE TYPE OF MAIN DRIVE PROVIDED FOR TURNING,ROTATING,OR POSITIONING THE MECHANISM. SELECT REPLY CODE 10AG25 BNQMA 12QUANTITY,RANGE,TABLE SPEED TABLE SPEED RANGE QUANTITY THE NUMBER OF TABLE SPEED RANGES PROVIDED. 1A MODE REPLY 0 BNQNA 12QUANTITY,SPEED,TABLE TABLE SPEED QUANTITY THE NUMBER OF TABLE SPEEDS PROVIDED. 1A MODE REPLY 0 BNQPJ 10SWING,MAXIMUM,SIDE HEAD IN WORKING POSITION SIDE HEAD IN WORKING POSITION MAXIMUM SWING THE MAXIMUM SWING DISTANCE WITH THE SIDE HEAD IN THE WORKING POSITION. 1D AND 1B MODE REPLY11AA05 BNQQJ 10SWING,MAXIMUM,SIDE HEAD BELOW TABLE TOP SIDE HEAD BELOW TABLE TOP MAXIMUM SWING THE MAXIMUM SWING DISTANCE WITH THE SIDE HEAD BELOW THE TOP OF THE TABLE. 1D AND 1B MODE REPLY11AA05 BNQRJ 04HEIGHT UNDER CROSSRAIL,MAXIMUM MAXIMUM HEIGHT UNDER CROSSRAIL THE MAXIMUM MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE ITEM UNDER THE CROSSRAIL,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BNQSJ 04HEIGHT UNDER TURRET FACE,MAXIMUM MAXIMUM HEIGHT UNDER TURRET FACE THE MAXIMUM MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE ITEM UNDER THE TURRET FACE,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BNQTA 12QUANTITY,HEAD,VERTICAL VERTICAL HEAD QUANTITY THE NUMBER OF VERTICAL HEADS ON THE ITEM. 1A MODE REPLY 0 BNQWJ 04DISTANCE,TRAVEL,VERTICAL,VERTICAL HEAD VERTICAL HEAD VERTICAL TRAVEL DISTANCE THE DISTANCE THE VERTICAL HEAD WILL TRAVEL IN A VERTICAL PLANE. 2D AND 1B MODE REPLY21AA051AC20 BNQXJ 04DISTANCE,TRAVEL,HORIZONTAL,VERTICAL HEAD VERTICAL HEAD HORIZONTAL TRAVEL DISTANCE THE DISTANCE THE VERTICAL HEAD WILL TRAVEL IN A HORIZONTAL PLANE. 2D AND 1B MODE REPLY21AA051AC20 BNQYB 04ANGLE IN DEG,ADJUSTMENT,VERTICAL HEAD VERTICAL HEAD ADJUSTMENT ANGLE IN DEG THE ANGLE TO WHICH THE VERTICAL HEAD MAY BE ADJUSTED,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BNQZA 12QUANTITY,FEED,VERTICAL HEAD VERTICAL HEAD FEED QUANTITY THE NUMBER OF VERTICAL HEAD FEEDS PROVIDED. 1A MODE REPLY 0 BNRBA 12QUANTITY,HEAD,SIDE SIDE HEAD QUANTITY THE NUMBER OF SIDE HEADS PROVIDED. 1A MODE REPLY 0 BNRCJ 04DISTANCE,TRAVEL,VERTICAL,SIDE HEAD SIDE HEAD VERTICAL TRAVEL DISTANCE THE DISTANCE THE SIDE HEAD WILL TRAVEL IN A VERTICAL PLANE. 2D AND 1B MODE REPLY21AA051AC20 BNRDJ 04DISTANCE,TRAVEL,HORIZONTAL,SIDE HEAD SIDE HEAD HORIZONTAL TRAVEL DISTANCE THE DISTANCE THE SIDE HEAD WILL TRAVEL IN A HORIZONTAL PLANE. 2D AND 1B MODE REPLY21AA051AC20 BNRFA 12QUANTITY,FEED,SIDE HEAD SIDE HEAD FEED QUANTITY THE NUMBER OF SIDE HEAD FEEDS PROVIDED. 1A MODE REPLY 0 BNRGD /D/ 07CUSHION,AIR,BED BED AIR CUSHION AN INDICATION OF WHETHER OR NOT A BED AIR CUSHION IS INCLUDED. SELECT REPLY CODE 10AA49 BNRHJ 04SIZE,ARM ARM SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE ARM. 1D AND 1B MODE REPLY11AA05 BNRJJ 04DIAMETER,COLUMN COLUMN DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COLUMN,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNRKJ A04SIZE,TAPER,SPINDLE SOCKET SPINDLE SOCKET TAPER SIZE DESIGNATES THE COMMERCIAL TAPER SIZE OF THE SPINDLE SOCKET. 1D AND 1A MODE REPLY12AH09 BNRLJ 04DISTANCE,TRAVEL,SPINDLE SPINDLE TRAVEL DISTANCE THE DISTANCE THE SPINDLE WILL TRAVEL. 2D AND 1B MODE REPLY21AA051AC20 BNRMJ 04DISTANCE FROM SPINDLE CENTER TO COLUMN,MAXIMUM MAXIMUM DISTANCE FROM SPINDLE CENTER TO COLUMN THE MAXIMUM DISTANCE FROM THE CENTER OF THE SPINDLE TO THE COLUMN. 1D AND 1B MODE REPLY11AA05 BNRNJ 04DISTANCE FROM SPINDLE CENTER TO COLUMN,MINIMUM MINIMUM DISTANCE FROM SPINDLE CENTER TO COLUMN THE MINIMUM DISTANCE FROM THE CENTER OF THE SPINDLE TO THE COLUMN. 1D AND 1B MODE REPLY11AA05 BNRPJ 04DISTANCE FROM SPINDLE NOSE TO BASE,MAXIMUM MAXIMUM DISTANCE FROM SPINDLE NOSE TO BASE THE MAXIMUM DISTANCE FROM THE NOSE OF THE SPINDLE TO THE BASE. 1D AND 1B MODE REPLY11AA05 BNRQJ 04DISTANCE FROM SPINDLE NOSE TO BASE,MINIMUM MINIMUM DISTANCE FROM SPINDLE NOSE TO BASE THE MINIMUM DISTANCE FROM THE NOSE OF THE SPINDLE TO THE BASE. 1D AND 1B MODE REPLY11AA05 BNRRD /D/ 07RECESS FOR PUNCH STEM,SLIDE SLIDE RECESS FOR PUNCH STEM AN INDICATION OF WHETHER OR NOT A RECESS IS INCLUDED IN THE SLIDE FOR THE PUNCH STEM. SELECT REPLY CODE 10AA49 BNRSD 14SHAPE,CROSS-SECTIONAL,RECESS RECESS CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE RECESS WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 BNRTJ 04DISTANCE ON ARM,TRAVEL,HEAD HEAD TRAVEL DISTANCE ON ARM THE DISTANCE THE HEAD WILL TRAVEL ON THE ARM. 2D AND 1B MODE REPLY21AA051AC20 BNRWJ 04LENGTH,SURFACE,WORKING,BASE BASE WORKING SURFACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BASE WORKING SURFACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BNRXJ 04WIDTH,SURFACE,WORKING,BASE BASE WORKING SURFACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BASE WORKING SURFACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BNRYG /D/ 10CAPABILITY,DRILLING DRILLING CAPABILITY THE DRILLING CAPABILITY/IES/ OF THE ITEM. FULL TEXT WRITE-IN 0 BNRZD 18TYPE,COLUMN COLUMN TYPE INDICATES THE TYPE OF COLUMN PROVIDED ON THE ITEM. SELECT REPLY CODE 10AK54 BNSBJ 04DISTANCE BETWEEN SPINDLE CENTERS DISTANCE BETWEEN SPINDLE CENTERS THE DISTANCE BETWEEN THE SPINDLE CENTERS. 2D AND 1B MODE REPLY21AA051AC20 BNSCG 04SIZE ACCOMMODATED,CHUCK,DRILL DRILL CHUCK SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE DRILL CHUCK THE ITEM WILL ACCOMMODATE. FULL TEXT WRITE-IN 0 BNSDJ 04DISTANCE FROM SPINDLE CENTER TO COLUMN DISTANCE FROM SPINDLE CENTER TO COLUMN THE DISTANCE FROM THE CENTER OF THE SPINDLE TO THE COLUMN. 2D AND 1B MODE REPLY21AA051AC20 BNSFD 18TYPE,SURFACE,WORKING,BASE BASE WORKING SURFACE TYPE INDICATES THE TYPE OF BASE WORKING SURFACE PROVIDED ON THE ITEM. SELECT REPLY CODE 10AK54 BNSGD 14SHAPE,SURFACE,WORKING,BASE BASE WORKING SURFACE SHAPE THE PHYSICAL CONFIGURATION OF THE BASE WORKING SURFACE. SELECT REPLY CODE 10AD07 BNSHJ 10AREA,SURFACE,WORKING,BASE BASE WORKING SURFACE AREA A MEASUREMENT OF THE BASE WORKING SURFACE AREA ON THE ITEM. 1D AND 1B MODE REPLY12AG67 BNSJJ 04DIAMETER,SURFACE,WORKING,BASE BASE WORKING SURFACE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BASE WORKING SURFACE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNSKJ 10ADJUSTMENT,VERTICAL,BASE WORKING SURFACE BASE WORKING SURFACE VERTICAL ADJUSTMENT THE DISTANCE THE BASE WORKING SURFACE CAN BE ADJUSTED VERTICALLY. 2D AND 1B MODE REPLY21AA051AC20 BNSLD /D/ 08LOCATION,MOUNTING,BASE WORKING SURFACE BASE WORKING SURFACE MOUNTING LOCATION INDICATES THE LOCATION OF THE ITEM ON WHICH THE BASE WORKING SURFACE IS MOUNTED. SELECT REPLY CODE 10AJ91 BNSMJ /D/ 04DISTANCE FROM CHUCK/SPINDLE NOSE TO BASE WORKING SURFACE,MAXIMUM MAXIMUM DISTANCE FROM CHUCK/SPINDLE NOSE TO BASE WORKING SURFACE THE MAXIMUM DISTANCE FROM THE CHUCK OR SPINDLE NOSE TO THE BASE WORKING SURFACE. 1D AND 1B MODE REPLY11AA05 BNSND 18TYPE,SURFACE,WORKING,UPPER UPPER WORKING SURFACE TYPE INDICATES THE TYPE OF UPPER WORKING SURFACE PROVIDED ON THE ITEM. SELECT REPLY CODE 10AK54 BNSPD 14SHAPE,SURFACE,WORKING,UPPER UPPER WORKING SURFACE SHAPE THE PHYSICAL CONFIGURATION OF THE UPPER WORKING SURFACE. SELECT REPLY CODE 10AD07 BNSQJ 10AREA,SURFACE,WORKING,UPPER UPPER WORKING SURFACE AREA A MEASUREMENT OF THE UPPER WORKING SURFACE AREA ON THE ITEM. 1D AND 1B MODE REPLY12AG67 BNSRJ 04DIAMETER,SURFACE,WORKING,UPPER UPPER WORKING SURFACE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE UPPER WORKING SURFACE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNSSJ 04LENGTH,SURFACE,WORKING,UPPER UPPER WORKING SURFACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE UPPER WORKING SURFACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BNSTJ 04WIDTH,SURFACE,WORKING,UPPER UPPER WORKING SURFACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE UPPER WORKING SURFACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BNSWD /D/ 07FEATURE,ADJUSTMENT,UPPER WORKING SURFACE UPPER WORKING SURFACE ADJUSTMENT FEATURE AN INDICATION OF WHETHER OR NOT AN UPPER WORKING SURFACE ADJUSTMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BNSXJ 10ADJUSTMENT,VERTICAL,UPPER WORKING SURFACE UPPER WORKING SURFACE VERTICAL ADJUSTMENT THE DISTANCE THE UPPER WORKING SURFACE CAN BE ADJUSTED VERTICALLY. 2D AND 1B MODE REPLY21AA051AC20 BNSYB 10ADJUSTMENT IN DEG,SWIVEL SWIVEL ADJUSTMENT IN DEG THE SWIVEL ADJUSTMENT,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BNSZJ /D/ 05DIRECTION AND ANGLE IN DEG,ADJUSTMENT,TILT TILT ADJUSTMENT DIRECTION AND ANGLE IN DEG THE DIRECTION AND NUMBER OF DEGREES IN WHICH THE ANGLE OF TILT CAN BE ADJUSTED. 1D AND 1B MODE REPLY13AK54 BNTBD /D/ 19FACILITY,ENGAGING/LOCKING/POSITIONING,FIRST END FIRST END ENGAGING/LOCKING/POSITIONING FACILITY THE FACILITY FURNISHED ON THE FIRST END FOR ENGAGING,LOCKING,AND/OR POSITIONING THE ITEM. SELECT REPLY CODE 10AA78 BNTCJ 04WIDTH,FACILITY,FIRST END FIRST END FACILITY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FACILITY ON THE FIRST END,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BNTDG /D/ 08LOCATION,FACILITY,FIRST END FIRST END FACILITY LOCATION INDICATES THE LOCATION OF THE FACILITY ON THE FIRST END OF THE ITEM. FULL TEXT WRITE-IN 0 BNTFD /D/ 07SEAT,BEARING,FIRST END FIRST END BEARING SEAT AN INDICATION OF WHETHER OR NOT A FIRST END BEARING SEAT/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BNTGJ 04WIDTH,SEAT,FIRST END BEARING FIRST END BEARING SEAT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BEARING SEAT ON THE FIRST END,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BNTHA 12QUANTITY,TEETH,SECOND END GEAR SECOND END GEAR TEETH QUANTITY THE NUMBER OF INDIVIDUAL TEETH ON THE SECOND END GEAR. 1A MODE REPLY 0 BNTJB 04ANGLE IN DEG,PRESSURE,SECOND END GEAR TEETH SECOND END GEAR TEETH PRESSURE ANGLE IN DEG THE PRESSURE ANGLE OF THE SECOND END GEAR TEETH,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BNTKJ 04DIAMETER,PITCH,SECOND END GEAR SECOND END GEAR PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF THE SECOND END GEAR. 2D AND 1B MODE REPLY21AA051AC20 BNTLD /D/ 05DIRECTION,TEETH,SECOND END GEAR SECOND END GEAR TEETH DIRECTION THE DIRECTION OF THE SECOND END GEAR TEETH WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AK54 BNTMD 18TYPE,SPLINE,SECOND END SECOND END SPLINE TYPE INDICATES THE TYPE OF SECOND END SPLINE PROVIDED. SELECT REPLY CODE 10AA85 BNTNB 04ANGLE IN DEG,PRESSURE,SECOND END SPLINE SECOND END SPLINE PRESSURE ANGLE IN DEG THE PRESSURE ANGLE OF THE SECOND END SPLINE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BNTPJ 04DIAMETER,HOLE,SECOND END PIN SECOND END PIN HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SECOND END PIN HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNTQD /D/ 19FACILITY,ENGAGING/LOCKING/POSITIONING,SECOND END SECOND END ENGAGING/LOCKING/POSITIONING FACILITY THE FACILITY FURNISHED ON THE SECOND END FOR ENGAGING,LOCKING,AND/OR POSITIONING THE ITEM. SELECT REPLY CODE 10AA78 BNTRJ 04WIDTH,FACILITY,SECOND END SECOND END FACILITY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FACILITY ON THE SECOND END,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BNTSG /D/ 08LOCATION,FACILITY,SECOND END SECOND END FACILITY LOCATION INDICATES THE LOCATION OF THE FACILITY ON THE SECOND END OF THE ITEM. FULL TEXT WRITE-IN 0 BNTTD /D/ 07SEAT,BEARING,SECOND END SECOND END BEARING SEAT AN INDICATION OF WHETHER OR NOT A SECOND END BEARING SEAT/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BNTWJ 04WIDTH,SEAT,SECOND END BEARING SECOND END BEARING SEAT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BEARING SEAT ON THE SECOND END,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BNTXD 18TYPE,HOLE,END END HOLE TYPE INDICATES THE TYPE OF HOLE(S) PROVIDED ON THE END OF THE ITEM. SELECT REPLY CODE 10AK54 BNTYJ 04DIAMETER,SEAT,SEAL SEAL SEAT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BNTZJ 04DEPTH,SEAT,SEAL SEAL SEAT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BNWBJ 04DISTANCE BETWEEN BODY END AND MOUNTING FLANGE,SHORTEST SHORTEST DISTANCE BETWEEN BODY END AND MOUNTING FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BNWCJ 04DISTANCE ACROSS FLANGE DISTANCE ACROSS FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BNWDJ 10SIZE,HOLE,SMALLEST MOUNTING SMALLEST MOUNTING HOLE SIZE NONE. 2D AND 1B MODE REPLY21AA051AC20 BNWFJ /D/ 04DISTANCE BETWEEN SMALLEST MOUNTING HOLE CENTERS DISTANCE BETWEEN SMALLEST MOUNTING HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BNWGJ 04DISTANCE BETWEEN CENTER APERTURE/MOUNTING HOLE AND END MOUNTING HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN CENTER APERTURE/MOUNTING HOLE AND END MOUNTING HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BNWHJ 04RADIUS,CENTER CENTER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BNWJB 04ANGLE BETWEEN EARS IN DEG ANGLE BETWEEN EARS IN DEG NONE. 1B MODE REPLY 0 BNWKB 04ANGLE FROM HORIZONTAL CENTERLINE TO EAR IN DEG ANGLE FROM HORIZONTAL CENTERLINE TO EAR IN DEG NONE. 1B MODE REPLY 0 BNWLA /D/ 16STYLE DESIGNATOR,VIEW,SIDE SIDE VIEW STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SIDE VIEW. 1A MODE REPLY 0 BNWMJ 04THICKNESS ACCOMMODATED,PANEL PANEL THICKNESS ACCOMMODATED A MEASUREMENT OF THE SMALLEST DIMENSION OF THE PANEL THE ITEM WILL ACCOMMODATE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BNWNJ 10SIZE ACCOMMODATED,SHANK SHANK SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE SHANK THE ITEM WILL ACCOMMODATE. 2D AND 1B MODE REPLY21AA051AC20 BNWPD /D/ 08LOCATION,FEATURE,PREBENT LOCKING PREBENT LOCKING FEATURE LOCATION INDICATES THE LOCATION OF THE PREBENT LOCKING FEATURE(S). SELECT REPLY CODE 10AJ91 BNWQJ T04THICKNESS RANGE,FLANGE,SUPPORTING STRUCTURAL MEMBER SUPPORTING STRUCTURAL MEMBER FLANGE THICKNESS RANGE THE MINIMUM AND MAXIMUM MEASUREMENT OF THE SMALLEST DIMENSION OF THE SUPPORTING STRUCTURAL MEMBER FLANGE,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1F MODE REPLY11AA05 BNWRJ /D/A19ITEM AND QUANTITY,SUPPORTED SUPPORTED ITEM AND QUANTITY AN INDICATION OF THE ITEM SUPPORTED AND THE NUMBER OF EACH. 1D AND 1A MODE REPLY13AK54 BNWSD /D/ 07FEATURE,YOKE YOKE FEATURE AN INDICATION OF WHETHER OR NOT A YOKE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BNWTG 03DESIGNATION,THICKNESS THICKNESS DESIGNATION A DESIGNATION INDICATING THE THICKNESS OF THE ITEM. FULL TEXT WRITE-IN 0 BNWWJ /D/ 04DIAMETER,HOOK HOOK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BNWXJ 04LENGTH FROM MOUNTING SURFACE,OVERALL OVERALL LENGTH FROM MOUNTING SURFACE THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS FROM THE MOUNTING SURFACE OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BNWZD 19POSITION,END END POSITION AN INDICATION OF THE POSITION OF THE END(S) ON THE ITEM. SELECT REPLY CODE 10AH21 BNXBJ 04WIDTH,FACE,FLANGE MOUNTING FLANGE MOUNTING FACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FLANGE MOUNTING FACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BNXCJ 04LENGTH,FACE,FLANGE MOUNTING FLANGE MOUNTING FACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FLANGE MOUNTING FACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BNXDG 08LOCATION,FLANGE,OUTPUT OUTPUT FLANGE LOCATION INDICATES THE LOCATION OF THE OUTPUT FLANGE/S/ ON THE ITEM. FULL TEXT WRITE-IN 0 BNXFD /D/ 18TYPE,KNUCKLE,STEERING STEERING KNUCKLE TYPE INDICATES THE TYPE OF STEERING KNUCKLE PROVIDED ON THE ITEM. SELECT REPLY CODE 10AC02 BNXGD /D/ 07ROD,TIE TIE ROD AN INDICATION OF WHETHER OR NOT A TIE ROD/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BNXHJ 04WIDTH,TRACK TRACK WIDTH A MEASUREMENT OF THE TRACK WIDTH OF THE ITEM. 1D AND 1B MODE REPLY11AA05 BNXJJ 04DISTANCE BETWEEN SPRING SEAT CENTERS DISTANCE BETWEEN SPRING SEAT CENTERS THE DISTANCE BETWEEN THE SPRING SEAT CENTERS. 2D AND 1B MODE REPLY21AA051AC20 BNXKD 18TYPE FOR WHICH DESIGNED,AXLE AXLE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF AXLE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AD07 BNXLD /D/ 07CARRIER CARRIER AN INDICATION OF WHETHER OR NOT A CARRIER IS INCLUDED. SELECT REPLY CODE 10AA49 BNXMD 18TYPE,AXLE AXLE TYPE INDICATES THE TYPE OF AXLE PROVIDED. SELECT REPLY CODE 10AK54 BNXND 18TYPE,GEAR,DRIVE DRIVE GEAR TYPE INDICATES THE TYPE OF DRIVE GEAR PROVIDED. SELECT REPLY CODE 10AC58 BNXPG /D/ 10RATIO,GEAR GEAR RATIO THE NUMBER OF TURNS OF THE DRIVING GEAR IN RELATION TO ONE OR MORE DRIVEN GEARS. FULL TEXT WRITE-IN 0 BNXQD /D/ 07FLANGE,SHAFT,PROPELLER PROPELLER SHAFT FLANGE AN INDICATION OF WHETHER OR NOT A PROPELLER SHAFT FLANGE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BNXRD /D/ 07YOKE,SHAFT,PROPELLER PROPELLER SHAFT YOKE AN INDICATION OF WHETHER OR NOT A PROPELLER SHAFT YOKE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BNXSD /D/ 07DIVIDER,POWER POWER DIVIDER AN INDICATION OF WHETHER OR NOT A POWER DIVIDER IS INCLUDED. SELECT REPLY CODE 10AA49 BNXTD /D/ 07CHAMBER,BRAKE BRAKE CHAMBER AN INDICATION OF WHETHER OR NOT A BRAKE CHAMBER/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BNXWD 19COMPONENTS,AXLE,FURNISHED FURNISHED AXLE COMPONENTS THE AXLE COMPONENTS FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AB28 BNXXA 12QUANTITY,TEETH,DRIVE GEAR DRIVE GEAR TEETH QUANTITY THE NUMBER OF DRIVE GEAR TEETH INCLUDED. 1A MODE REPLY 0 BNXYB 04ANGLE IN DEG,PRESSURE,DRIVE GEAR TEETH DRIVE GEAR TEETH PRESSURE ANGLE IN DEG THE PRESSURE ANGLE OF THE DRIVE GEAR TEETH,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BNXZG /D/ 10PITCH,GEAR,DRIVE DRIVE GEAR PITCH THE DISTANCE BETWEEN ONE POINT ON A DRIVE GEAR TOOTH AND THE CORRESPONDING POINT ON THE NEXT TOOTH. FULL TEXT WRITE-IN 0 BNYBD /D/ 07CABLE,CONTROL CONTROL CABLE AN INDICATION OF WHETHER OR NOT A CONTROL CABLE IS INCLUDED. SELECT REPLY CODE 10AA49 BNYCD /D/ 07ACCOMMODATION,UNIT,ACCESSORY DRIVE ACCESSORY DRIVE UNIT ACCOMMODATION AN INDICATION OF WHETHER OR NOT AN ACCESSORY DRIVE UNIT ACCOMMODATION IS INCLUDED. SELECT REPLY CODE 10AA49 BNYDD /D/ 07UNIT,DRIVE,ACCESSORY ACCESSORY DRIVE UNIT AN INDICATION OF WHETHER OR NOT AN ACCESSORY DRIVE UNIT IS INCLUDED. SELECT REPLY CODE 10AA49 BNYFA 12QUANTITY,END,OUTPUT SHAFT DRIVE OUTPUT SHAFT DRIVE END QUANTITY THE NUMBER OF DRIVE END(S) PROVIDED ON THE OUTPUT SHAFT. 1A MODE REPLY 0 BNYGD /D/ 08LOCATION,END,DRIVE DRIVE END LOCATION INDICATES THE LOCATION OF THE DRIVE ENDS. SELECT REPLY CODE 10AJ91 BNYHD 18TYPE,END,OUTPUT SHAFT DRIVE OUTPUT SHAFT DRIVE END TYPE INDICATES THE TYPE OF DRIVE END ON THE OUTPUT SHAFT. SELECT REPLY CODE 10AK95 BNYJD 11METHOD,SECURING,DRIVE END DRIVE END SECURING METHOD THE MEANS BY WHICH THE DRIVE END IS MODIFIED FOR SECURING. SELECT REPLY CODE 10AB76 BNYKD /D/ 07ASSEMBLY,ADAPTER,DRIVE GEAR EXTENSION DRIVE GEAR EXTENSION ADAPTER ASSEMBLY AN INDICATION OF WHETHER OR NOT A DRIVE GEAR EXTENSION ADAPTER ASSEMBLY IS INCLUDED. SELECT REPLY CODE 10AA49 BNYLA 03DESIGNATION,MOUNTING,SAE STANDARD SAE STANDARD MOUNTING DESIGNATION THE TYPE OR GROUP DESIGNATION OF THE SOCIETY OF AUTOMOTIVE ENGINEERS STANDARD MOUNTING. 1A MODE REPLY 0 BNYMD /D/ 07ADAPTER,PLATE,MOUNTING,SAE STANDARD SAE STANDARD MOUNTING PLATE ADAPTER AN INDICATION OF WHETHER OR NOT A SOCIETY OF AUTOMOTIVE ENGINEERS MOUNTING PLATE ADAPTER IS INCLUDED. SELECT REPLY CODE 10AA49 BNYNA 12QUANTITY,TEETH,FIRST END GEAR FIRST END GEAR TEETH QUANTITY THE NUMBER OF INDIVIDUAL TEETH ON THE FIRST END GEAR. 1A MODE REPLY 0 BNYPB 04ANGLE IN DEG,PRESSURE,FIRST END GEAR TEETH FIRST END GEAR TEETH PRESSURE ANGLE IN DEG THE PRESSURE ANGLE OF THE FIRST END GEAR TEETH,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BNYQJ 04DIAMETER,PITCH,FIRST END GEAR FIRST END GEAR PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF THE FIRST END GEAR. 2D AND 1B MODE REPLY21AA051AC20 BNYRD /D/ 05DIRECTION,TEETH,FIRST END GEAR FIRST END GEAR TEETH DIRECTION THE DIRECTION OF THE FIRST END GEAR TEETH WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AJ91 BNYSJ 04THICKNESS,OVERALL,FLANGE FLANGE OVERALL THICKNESS AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF THE FLANGE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BNYTJ 04THICKNESS AT MOUNTING HOLE,FLANGE FLANGE THICKNESS AT MOUNTING HOLE A MEASUREMENT OF THE SMALLEST DIMENSION OF THE FLANGE AT THE MOUNTING HOLE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BNYWJ 04TAPER,HOLE,FLANGE FLANGE HOLE TAPER THE TAPER OF THE FLANGE HOLE/S/ PER MEASUREMENT SCALE. 3D AND 1B MODE REPLY31AA051AC201AB39 BNYXD 18TYPE,SPLINE,FIRST END FIRST END SPLINE TYPE INDICATES THE TYPE OF FIRST END SPLINE PROVIDED. SELECT REPLY CODE 10AA85 BNYYB 04ANGLE IN DEG,PRESSURE,FIRST END SPLINE FIRST END SPLINE PRESSURE ANGLE IN DEG THE PRESSURE ANGLE OF THE FIRST END SPLINE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BNYZJ 04DIAMETER,HOLE,FIRST END PIN FIRST END PIN HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FIRST END PIN HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNZBJ /D/ 10AREA,RUDDER RUDDER AREA A MEASUREMENT OF THE RUDDER AREA. 2D AND 1B MODE REPLY21AC511AC20 BNZCB /D/ 10TURN IN DEG,RUDDER RUDDER TURN IN DEG THE NUMBER OF DEGREES THE RUDDER WILL TURN. 1B MODE REPLY 0 BNZDD /D/ 11METHOD,OPERATION,RUDDER RUDDER OPERATION METHOD THE MEANS BY WHICH THE RUDDER IS OPERATED. SELECT REPLY CODE 10AC58 BNZFD /D/ 11METHOD,OPERATION,RUDDER/PROPELLER RAISING/LOWERING MECHANISM RUDDER/PROPELLER RAISING/LOWERING MECHANISM OPERATION METHOD THE MEANS BY WHICH THE RUDDER AND PROPELLER RAISING AND LOWERING MECHANISM IS OPERATED. SELECT REPLY CODE 10AC58 BNZGA /D/ 12QUANTITY,POSITION,RUDDER/PROPELLER RUDDER/PROPELLER POSITION QUANTITY THE NUMBER OF POSITION(S) WHICH THE RUDDER AND PROPELLER CAN BE ADJUSTED. 1A MODE REPLY 0 BNZHD /D/ 11METHOD,LOCKING,RUDDER/PROPELLER RUDDER/PROPELLER LOCKING METHOD THE MEANS BY WHICH THE RUDDER AND PROPELLER CAN BE LOCKED. SELECT REPLY CODE 10AC82 BNZJD /D/ 07CROSSBEAMS,MOUNTING MOUNTING CROSSBEAMS AN INDICATION OF WHETHER OR NOT MOUNTING CROSSBEAMS ARE INCLUDED. SELECT REPLY CODE 10AA49 BNZKA 12QUANTITY FOR WHICH DESIGNED,BLADE BLADE QUANTITY FOR WHICH DESIGNED THE NUMBER OF BLADE(S) FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 BNZLD 18TYPE FOR WHICH DESIGNED,PROPELLER PROPELLER TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF PROPELLER FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL59 BNZMJ 04DIAMETER,OUTSIDE,AFT FACE AFT FACE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE AFT FACE OF THE ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNZNJ 04DIAMETER,OUTSIDE,FORWARD FACE FORWARD FACE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FORWARD FACE OF THE ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNZPD /D/ 19POSITION POSITION THE POSITION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AJ50 BNZQJ 04DIAMETER FOR WHICH DESIGNED,OUTSIDE,PROPELLER PROPELLER OUTSIDE DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PROPELLER FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNZRD 18TYPE,END,INPUT SHAFT INPUT SHAFT END TYPE INDICATES THE TYPE OF INPUT SHAFT END PROVIDED. SELECT REPLY CODE 10AF58 BNZSJ 04DIAMETER,OUTSIDE,MOUNTING FACE MOUNTING FACE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MOUNTING FACE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BNZTJ 04WIDTH,FACE,MOUNTING MOUNTING FACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING FACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BNZWJ 04LENGTH,FACE,MOUNTING MOUNTING FACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING FACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BNZXA 12QUANTITY,END,OUTPUT SHAFT OUTPUT SHAFT END QUANTITY THE NUMBER OF OUTPUT SHAFT END(S) PROVIDED. 1A MODE REPLY 0 BNZYD 18TYPE,END,OUTPUT SHAFT OUTPUT SHAFT END TYPE INDICATES THE TYPE OF OUTPUT SHAFT END PROVIDED. SELECT REPLY CODE 10AF58 BNZZJ 04DIAMETER,OUTSIDE,FLANGE MOUNTING FACE FLANGE MOUNTING FACE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FLANGE MOUNTING FACE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BPBBJ 10AMOUNT,ANTICOAGULANT ANTICOAGULANT AMOUNT THE AMOUNT OF ANTICOAGULANT PROVIDED. 1D AND 1B MODE REPLY12AG67 BPBCD 18TYPE,CONNECTION,TOWED END TOWED END CONNECTION TYPE INDICATES THE TYPE OF TOWED END CONNECTION PROVIDED. SELECT REPLY CODE 10AB76 BPBDD 18TYPE,CONNECTION,TOWING END TOWING END CONNECTION TYPE INDICATES THE TYPE OF TOWING END CONNECTION PROVIDED. SELECT REPLY CODE 10AB76 BPBFD 07ADJUSTABILITY,LENGTH LENGTH ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE LENGTH IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BPBGJ T10RANGE,SPREAD,ADJUSTABLE,TOWED END TOWED END ADJUSTABLE SPREAD RANGE THE MINIMUM TO MAXIMUM LIMITS OF THE ADJUSTABLE SPREAD AT THE TOWED END. 1D AND 1F MODE REPLY11AA05 BPBHJ 04DIAMETER,CASTER CASTER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CASTER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BPBJD 07PROVISION,THREAD,SHANK END SHANK END THREAD PROVISION AN INDICATION OF WHETHER OR NOT THE SHANK END IS THREADED. SELECT REPLY CODE 10AE00 BPBKD /D/ 07KEYWAY,END,SHANK SHANK END KEYWAY AN INDICATION OF WHETHER OR NOT THE SHANK END IS PROVIDED WITH A KEYWAY. SELECT REPLY CODE 10AB22 BPBLJ 04LENGTH FROM FLANGE TO THROAT CENTER LENGTH FROM FLANGE TO THROAT CENTER A MEASUREMENT OF THE LONGEST DIMENSION FROM THE FLANGE TO THE CENTER OF THE THROAT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BPBMD /D/ 07SLEEVE,SPRING SPRING SLEEVE AN INDICATION OF WHETHER OR NOT A SPRING SLEEVE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BPBND /D/ 07HOUSING,SPRING SPRING HOUSING AN INDICATION OF WHETHER OR NOT A SPRING HOUSING IS INCLUDED. SELECT REPLY CODE 10AA49 BPBPJ 04LENGTH FROM SHANK END TO THROAT CENTER LENGTH FROM SHANK END TO THROAT CENTER A MEASUREMENT OF THE LONGEST DIMENSION FROM THE END OF THE SHANK TO THE CENTER OF THE THROAT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BPBQJ 10SIZE,OPENING,THROAT THROAT OPENING SIZE DESIGNATES THE SIZE OF THE THROAT OPENING. 2D AND 1B MODE REPLY21AA051AC20 BPBRD /D/ 07HOLE,PIN,COTTER,DRILLED DRILLED COTTER PIN HOLE AN INDICATION OF WHETHER OR NOT A DRILLED COTTER PIN HOLE IS INCLUDED. SELECT REPLY CODE 10AA49 BPBSD /D/ 07HOLE,LEVER,LATCH LATCH LEVER HOLE AN INDICATION OF WHETHER OR NOT A LATCH LEVER HOLE IS INCLUDED. SELECT REPLY CODE 10AA49 BPBTD /D/ 18TYPE FOR WHICH DESIGNED,PINTLE PINTLE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF PINTLE FOR WHICH THE ITEM WAS DESIGNED. SELECT REPLY CODE 10AK54 BPBWD /D/ 07HOLE,LOCKING,THREADED PIVOT PIN THREADED PIVOT PIN LOCKING HOLE AN INDICATION OF WHETHER OR NOT A THREADED PIVOT PIN LOCKING HOLE IS INCLUDED. SELECT REPLY CODE 10AA49 BPBXB 04ANGLE DEG,SHANK SHANK ANGLE DEG NONE. 1B MODE REPLY 0 BPBYJ 04DIAMETER,END,UNTHREADED SHANK UNTHREADED SHANK END DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BPBZJ /D/ 04LENGTH,SHANK,MOUNTING MOUNTING SHANK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BPCBJ /D/ 04DIAMETER,SHANK,MOUNTING MOUNTING SHANK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BPCCJ /D/ 04DIAMETER,ACCOMMODATION,MOUNTING SHANK RING MOUNTING SHANK RING ACCOMMODATION DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BPCDJ 04LENGTH,DRAWBAR DRAWBAR LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BPCFJ /D/ 04HEIGHT,DRAWBAR DRAWBAR HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BPCGJ /D/ 04THICKNESS,DRAWBAR DRAWBAR THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BPCHJ 04WIDTH AT PIVOT PIN HOLE WIDTH AT PIVOT PIN HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BPCJJ 04DISTANCE BETWEEN HOLE CENTERS DISTANCE BETWEEN HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BPCKJ 04THICKNESS,SMALLEST SMALLEST THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BPCLJ 04RADIUS,INSIDE,HOOK HOOK INSIDE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BPCMJ 04WIDTH,SMALLEST SMALLEST WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BPCNJ 04DIAMETER,HOLE,LOCKING PIN LOCKING PIN HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BPCPJ 04DISTANCE FROM PIVOT PIN HOLE CENTER TO ROLLER PIN HOLE CENTER DISTANCE FROM PIVOT PIN HOLE CENTER TO ROLLER PIN HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 BPCQJ 10SIZE ACCOMMODATED,CONDUIT CONDUIT SIZE ACCOMMODATED DESIGNATES THE STANDARD SIZE OF THE CONDUIT THE ITEM WILL ACCOMMODATE. 2D AND 1B MODE REPLY21AA051AC20 BPCRD 18TYPE,THREAD THREAD TYPE INDICATES THE TYPE OF THREAD PROVIDED. SELECT REPLY CODE 10AL72 BPCSJ 04LENGTH FROM HOLE CENTER TO HOOK HEAD CENTER LENGTH FROM HOLE CENTER TO HOOK HEAD CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 BPCTJ 10SIZE FOR WHICH DESIGNED,KNOCKOUT KNOCKOUT SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE KNOCKOUT FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 BPCWJ A04SIZE FOR WHICH DESIGNED,WIRE WIRE SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE WIRE FOR WHICH THE ITEM IS DESIGNED. 1D AND 1A MODE REPLY12AG67 BPCXD /D/ 07CONNECTION,TYPE,SOLDER SOLDER TYPE CONNECTION AN INDICATION OF WHETHER OR NOT A SOLDER TYPE CONNECTION IS PROVIDED. SELECT REPLY CODE 10AB22 BPCYD /D/ 07SEAL,WATER WATER SEAL AN INDICATION OF WHETHER OR NOT A WATER SEAL IS PROVIDED. SELECT REPLY CODE 10AB22 BPCZD /D/ 07FEATURE,SEPARABILITY,RACEWAY RACEWAY SEPARABILITY FEATURE AN INDICATION OF WHETHER OR NOT A RACEWAY SEPARABILITY FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BPDBD /D/ 07FEATURE,USAGE,UNDERFLOOR UNDERFLOOR USAGE FEATURE AN INDICATION OF WHETHER OR NOT AN UNDERFLOOR USAGE FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BPDCD 08LOCATION,CHAMFER CHAMFER LOCATION INDICATES THE LOCATION OF THE CHAMFER(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 BPDDG 04SIZE,CHAMFER CHAMFER SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE CHAMFER. FULL TEXT WRITE-IN 0 BPDFD 11METHOD,SECURING,ELEMENT ELEMENT SECURING METHOD THE MEANS BY WHICH THE ELEMENT IS SECURED TO THE ITEM. SELECT REPLY CODE 10AM39 BPDGA 19AGENCY,CONTROLLING,CELL CELL CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY CONTROLLING THE CELL. 1A MODE REPLY 0 BPDHJ A19NUMBER,IDENTIFYING,CELL CELL IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE CELL. 1D AND 1A MODE REPLY12AG99 BPDJA 12QUANTITY,ELEMENT,OPTICAL OPTICAL ELEMENT QUANTITY THE NUMBER OF OPTICAL ELEMENTS INCLUDED. 1A MODE REPLY 0 BPDKD 18TYPE,ELEMENT,OPTICAL OPTICAL ELEMENT TYPE INDICATES THE TYPE OF OPTICAL ELEMENT PROVIDED. SELECT REPLY CODE 10AM04 BPDLA 19AGENCY,CONTROLLING,OPTICAL ELEMENT OPTICAL ELEMENT CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE OPTICAL ELEMENT. 1A MODE REPLY 0 BPDMJ A19NUMBER,IDENTIFYING,OPTICAL ELEMENT OPTICAL ELEMENT IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE OPTICAL ELEMENT. 1D AND 1A MODE REPLY12AG99 BPDNJ 04DIAMETER,INSIDE,VIEWING END VIEWING END INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO SURFACES OF THE VIEWING END OF THE ITEM,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BPDPJ 04DIAMETER,INSIDE,ATTACHMENT END ATTACHMENT END INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO SURFACES OF THE ATTACHMENT END OF THE ITEM,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BPDQD /D/ 07PERIPHERY,KNURLED KNURLED PERIPHERY AN INDICATION OF WHETHER OR NOT A KNURLED PERIPHERY IS PROVIDED. SELECT REPLY CODE 10AB22 BPDRD 19GRADUATIONS/MARKINGS GRADUATIONS/MARKINGS AN INDICATION OF THE GRADUATIONS AND/OR MARKINGS ON THE ITEM. SELECT REPLY CODE 10AJ65 BPDSG 19INSCRIPTION,IDENTIFICATION,AMMUNITION AMMUNITION IDENTIFICATION INSCRIPTION THE ITEM INSCRIPTION IDENTIFYING THE AMMUNITION FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 BPDTJ 04THICKNESS,EDGE EDGE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION ACROSS THE EDGE OF AN ITEM FROM ONE SURFACE TO ANOTHER,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BPDWJ 04DEPTH AND LOCATION,BEVEL BEVEL DEPTH AND LOCATION A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE BEVEL,IN DISTINCTION FROM HEIGHT,AND ITS LOCATION. 3D AND 1B MODE REPLY31AA051AC203AJ91 BPDXD /D/ 07MECHANISM,ADJUSTMENT,AZIMUTH AZIMUTH ADJUSTMENT MECHANISM AN INDICATION OF WHETHER OR NOT A MECHANISM FOR AZIMUTH ADJUSTMENT IS PROVIDED. SELECT REPLY CODE 10AB22 BPDYD /D/ 07MECHANISM,ADJUSTMENT,ELEVATION ELEVATION ADJUSTMENT MECHANISM AN INDICATION OF WHETHER OR NOT A MECHANISM FOR ELEVATION ADJUSTMENT IS PROVIDED. SELECT REPLY CODE 10AB22 BPDZD /D/ 07ACCOMMODATION,LIGHT,INSTRUMENT INSTRUMENT LIGHT ACCOMMODATION AN INDICATION OF WHETHER OR NOT AN ACCOMMODATION(S) FOR AN INSTRUMENT LIGHT(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BPFBD 19FACILITY,CALIBRATION,STAGE STAGE CALIBRATION FACILITY AN INDICATION OF THE STAGE CALIBRATION FACILITY PROVIDED. SELECT REPLY CODE 10AJ12 BPFCD 02DESIGN,CONDENSER,SUBSTAGE SUBSTAGE CONDENSER DESIGN THE DESIGN OF THE SUBSTAGE CONDENSER. SELECT REPLY CODE 10AM04 BPFDD 07ADJUSTABILITY,CONDENSER CONDENSER ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE CONDENSER IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BPFFD 18TYPE,DIAPHRAGM,IRIS IRIS DIAPHRAGM TYPE INDICATES THE TYPE OF IRIS DIAPHRAGM. SELECT REPLY CODE 10AK54 BPFGD /D/ 07POLARIZER POLARIZER AN INDICATION OF WHETHER OR NOT A POLARIZER IS PROVIDED. SELECT REPLY CODE 10AB22 BPFHA 12QUANTITY,MIRROR MIRROR QUANTITY THE NUMBER OF MIRROR(S) PROVIDED. 1A MODE REPLY 0 BPFJD 19CONTOUR,SURFACE,MIRROR MIRROR SURFACE CONTOUR THE PHYSICAL CONFIGURATION OF THE MIRROR FACE/S/. SELECT REPLY CODE 10AD07 BPFKD 02DESIGN,NOSEPIECE NOSEPIECE DESIGN THE DESIGN OF THE NOSEPIECE. SELECT REPLY CODE 10AK54 BPFLA 12QUANTITY,PLACE,NOSEPIECE NOSEPIECE PLACE QUANTITY THE NUMBER OF PLACE(S) PROVIDED ON THE NOSEPIECE. 1A MODE REPLY 0 BPFMA 12QUANTITY,OBJECTIVE OBJECTIVE QUANTITY THE NUMBER OF OBJECTIVE(S) PROVIDED. 1A MODE REPLY 0 BPFNA 19POWER EXCLUDING FRONT ELEMENT,OBJECTIVE,DIVISIBLE DIVISIBLE OBJECTIVE POWER EXCLUDING FRONT ELEMENT THE DESIGNATION INDICATING THE AMOUNT OF APPARENT ENLARGEMENT BY A DIVISIBLE OBJECTIVE,EXCLUDING THE FRONT ELEMENT. 1A MODE REPLY 0 BPFPD /D/ 07FEATURE,DESIGN,FUNNEL STOP FUNNEL STOP DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A FUNNEL STOP DESIGN FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BPFQD /D/ 07DIAPHRAGM,IRIS,OBJECTIVE OBJECTIVE IRIS DIAPHRAGM AN INDICATION OF WHETHER OR NOT AN IRIS DIAPHRAGM IS PROVIDED ON THE OBJECTIVE. SELECT REPLY CODE 10AB22 BPFRD /D/ 07SCALE,MICROMETER,MOUNTED MOUNTED MICROMETER SCALE AN INDICATION OF WHETHER OR NOT A MOUNTED MICROMETER SCALE IS PROVIDED. SELECT REPLY CODE 10AB22 BPFSD /D/ 09MATERIAL,PANEL,REMOVABLE REMOVABLE PANEL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE REMOVABLE PANEL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BPFTD 01COLOR,PANEL,REMOVABLE REMOVABLE PANEL COLOR THE HUE OR TINT OF THE REMOVABLE PANEL. SELECT REPLY CODE 10AD06 BPFWA 12QUANTITY,EYEPIECE EYEPIECE QUANTITY THE NUMBER OF EYEPIECE(S) PROVIDED. 1A MODE REPLY 0 BPFXD 03DESIGNATOR,EYEPIECE EYEPIECE DESIGNATOR A DESIGNATION BY WHICH THE EYEPIECE IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. SELECT REPLY CODE 10AK54 BPFYA 19MAGNIFICATION,EYEPIECE EYEPIECE MAGNIFICATION A DESIGNATION INDICATING THE AMOUNT OF APPARENT ENLARGEMENT BY THE EYEPIECE. 1A MODE REPLY 0 BPFZD /D/ 07EYEPIECE,FIELD,WIDE WIDE FIELD EYEPIECE AN INDICATION OF WHETHER OR NOT A WIDE FIELD EYEPIECE IS PROVIDED. SELECT REPLY CODE 10AB22 BPGBA 13THREAD SIZE,FLANGE FLANGE THREAD SIZE NONE. 1A MODE REPLY 0 BPGCD /D/ 13THREAD LOCATION,CONNECTION,AIR HOSE AIR HOSE CONNECTION THREAD LOCATION THE PORTION OF THE AIR HOSE CONNECTION ON WHICH THE THREADS ARE LOCATED. SELECT REPLY CODE 10AJ91 BPGDA 13THREAD SIZE,CONNECTION,EXTENSION EXTENSION CONNECTION THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE EXTENSION CONNECTION. 1A MODE REPLY 0 BPGFD 13THREAD SERIES,CONNECTION,EXTENSION EXTENSION CONNECTION THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF THE EXTENSION CONNECTION. SELECT REPLY CODE 10AH06 BPGGD 13THREAD LOCATION,CONNECTION,EXTENSION EXTENSION CONNECTION THREAD LOCATION INDICATES THE LOCATION OF THE EXTENSION CONNECTION ON WHICH THE THREADS ARE LOCATED. SELECT REPLY CODE 10AJ91 BPGHA 12QUANTITY,CONTAINER,ADDITIONAL GREASE ADDITIONAL GREASE CONTAINER QUANTITY THE NUMBER OF ADDITIONAL GREASE CONTAINER(S) PROVIDED. 1A MODE REPLY 0 BPGJD /D/ 07METHOD,HEATING,RESERVOIR RESERVOIR HEATING METHOD AN INDICATION OF WHETHER OR NOT A RESERVOIR HEATING METHOD IS INCLUDED. SELECT REPLY CODE 10AA49 BPGKD /D/ 07COMPARTMENT,STOWAGE STOWAGE COMPARTMENT AN INDICATION OF WHETHER OR NOT A STOWAGE COMPARTMENT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BPGLD /D/ 07REEL,HOSE HOSE REEL AN INDICATION OF WHETHER OR NOT A HOSE REEL IS INCLUDED. SELECT REPLY CODE 10AA49 BPGMD 11METHOD,OPERATION,REEL REEL OPERATION METHOD THE MEANS USED TO OPERATE THE REEL. SELECT REPLY CODE 10AC58 BPGND /D/ 07BRAKES,PARKING PARKING BRAKES AN INDICATION OF WHETHER OR NOT PARKING BRAKES ARE INCLUDED. SELECT REPLY CODE 10AA49 BPGPD 18TYPE,HITCH HITCH TYPE INDICATES THE TYPE OF HITCH PROVIDED. SELECT REPLY CODE 10AE35 BPGQD /D/ 19CHARACTERISTIC,DIRECTIONAL DIRECTIONAL CHARACTERISTIC AN INDICATION OF THE DIRECTIONAL CHARACTERISTIC OF THE ITEM. SELECT REPLY CODE 10AK54 BPGRD /D/ 02DESIGN,HITCH HITCH DESIGN THE DESIGN OF THE HITCH. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/16/2024 SELECT REPLY CODE 10AH28 BPGSD /D/ 07FITTINGS,LIFTING/TIEDOWN LIFTING/TIEDOWN FITTINGS AN INDICATION OF WHETHER OR NOT LIFTING AND TIEDOWN FITTINGS ARE INCLUDED. SELECT REPLY CODE 10AA49 BPGTD 18TYPE,CONNECTION,INLET FITTING INLET FITTING CONNECTION TYPE INDICATES THE TYPE OF INLET FITTING CONNECTION PROVIDED. SELECT REPLY CODE 10AB76 BPGWD 18TYPE,CONNECTION,NOZZLE NOZZLE CONNECTION TYPE INDICATES THE TYPE OF NOZZLE CONNECTION PROVIDED. SELECT REPLY CODE 10AB76 BPGXD 11METHOD,ENGAGEMENT ENGAGEMENT METHOD THE MEANS USED TO ENGAGE THE ITEM. SELECT REPLY CODE 10AM39 BPGYD /D/ 07LEVER,SELF-CLOSING SELF-CLOSING LEVER AN INDICATION OF WHETHER OR NOT A SELF-CLOSING LEVER IS INCLUDED. SELECT REPLY CODE 10AA49 BPGZD 18TYPE,SURFACE,SEATING SEATING SURFACE TYPE INDICATES THE TYPE OF SEATING SURFACE PROVIDED. SELECT REPLY CODE 10AH67 BPHBB 10DEGREE,SWIVEL SWIVEL DEGREE AN INDICATION OF THE DEGREE OF SWIVEL. 1B MODE REPLY 0 BPHCD /D/ 07POSITIONS,LOCKING LOCKING POSITIONS AN INDICATION OF WHETHER OR NOT LOCKING POSITIONS ARE INCLUDED. SELECT REPLY CODE 10AA49 BPHDJ 10PRESSURE,WORKING,MAXIMUM MAXIMUM WORKING PRESSURE THE MAXIMUM WORKING PRESSURE AT WHICH AN ITEM IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY12AG67 BPHFJ 04LENGTH,OVERALL,EXTENSION EXTENSION OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE EXTENSION. 2D AND 1B MODE REPLY21AA051AC20 BPHGD 13THREAD SERIES DESIGNATOR,CONNECTION CONNECTION THREAD SERIES DESIGNATOR A DESIGNATOR INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF THE THREADED CONNECTION. SELECT REPLY CODE 10AH06 BPHHD /D/ 07VALVE,CHECK CHECK VALVE AN INDICATION OF WHETHER OR NOT A CHECK VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 BPHKD /D/ 07DESIGN,EXTENSION EXTENSION DESIGN AN INDICATION OF WHETHER OR NOT AN EXTENSION DESIGN IS INCLUDED. SELECT REPLY CODE 10AA49 BPHLG /D/ 10EQUIVALENT,MINIMUM,PYROMETRIC CONE PYROMETRIC CONE MINIMUM EQUIVALENT AN INDICATION OF THE MINIMUM PYROMETRIC CONE EQUIVALENT. FULL TEXT WRITE-IN 0 BPHMJ 10MODULUS,RUPTURE,MINIMUM MINIMUM RUPTURE MODULUS AN INDICATION OF THE MINIMUM MODULUS BEFORE RUPTURE. 1D AND 1B MODE REPLY12AG67 BPHND /D/ 09MATERIAL,COMPONENT COMPONENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH A COMPONENT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BPHPD 18TYPE,SETTING SETTING TYPE INDICATES THE TYPE OF SETTING PROVIDED. SELECT REPLY CODE 10AK54 BPHQJ /D/ 10TEMP,VITRIFICATION VITRIFICATION TEMP AN INDICATION OF THE TEMPERATURE AT WHICH THE ITEM BECOMES VITRIFIED. 1D AND 1B MODE REPLY12AG67 BPHRJ 10TEMP FOR WHICH DESIGNED,MAXIUM MAXIMUM TEMP FOR WHICH DESIGNED THE MAXIMUM VALUE WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AS APPLIED TO THE OPERATION,OR LIMITATION OF OPERATION FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY12AG67 BPHSD 11METHOD,PREPARATION PREPARATION METHOD THE MEANS USED TO PREPARE THE ITEM. SELECT REPLY CODE 10AC58 BPHTG 10LIMITATION IN PERCENT,IMPURITIES,MAXIMUM MAXIMUM IMPURITIES LIMITATION IN PERCENT THE MAXIMUM LIMITATIONS PLACED ON IMPURITIES TO MAKE THE ITEM SUITABLE FOR PARTICULAR USES. FULL TEXT WRITE-IN 0 BPHWG 04SIZE GRADATION PERCENTAGE,PARTICLE PARTICLE SIZE GRADATION PERCENTAGE THE RETAINED MINIMUM AND/OR MAXIMUM PARTICLES FROM PROCESS OF SCREENING IN PERCENTAGE. FULL TEXT WRITE-IN 0 BPHXJ /D/ 04DIAMETER,INSIDE,LARGE LARGE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BPHYJ /D/ 04LENGTH,FACE,FRONT FRONT FACE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BPHZJ /D/ 04DISTANCE FROM BOLT CENTER TO OUTER EDGE ALONG WIDTH DISTANCE FROM BOLT CENTER TO OUTER EDGE ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BPJBJ /D/ 04DISTANCE FROM BOLT CENTER TO OUTER EDGE ALONG LENGTH DISTANCE FROM BOLT CENTER TO OUTER EDGE ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BPJCD /D/ 07INSERT,PRESET PRESET INSERT AN INDICATION OF WHETHER OR NOT A PRESET INSERT IS PROVIDED. SELECT REPLY CODE 10AB22 BPJDD /D/ 07FACILITY,MOUNTING MOUNTING FACILITY AN INDICATION OF WHETHER OR NOT A MOUNTING FACILITY IS INCLUDED. SELECT REPLY CODE 10AA49 BPJFJ 04DISTANCE BETWEEN MOUNTING HOLE AND FERRULE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLE AND FERRULE THE DISTANCE BETWEEN THE CENTERLINE OF THE MOUNTING HOLE AND THE CENTERLINE OF THE FERRULE. 2D AND 1B MODE REPLY21AA051AC20 BPJGJ 04THREAD DIAMETER,MOUNTING,MAJOR MAJOR MOUNTING THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST THREADED MOUNTING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BPJHG 19AGENCY,CONTROLLING,CABLE CABLE CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE CABLE. FULL TEXT WRITE-IN 0 BPJJG /D/ 19NUMBER,IDENTIFYING,CABLE CABLE IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE CABLE. FULL TEXT WRITE-IN 0 BPJKD 18TYPE,DESIGN,SLEEVE SLEEVE DESIGN TYPE INDICATES THE TYPE OF SLEEVE DESIGN. SELECT REPLY CODE 10AK54 BPJLJ 04LENGTH ACROSS MOUNTING ENDS,OVERALL,BODY BODY OVERALL LENGTH ACROSS MOUNTING ENDS THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BODY ACROSS THE MOUNTING ENDS. 2D AND 1B MODE REPLY21AA051AC20 BPJMJ 04RADIUS,OUTSIDE,BODY CURVATURE BODY CURVATURE OUTSIDE RADIUS THE OUTSIDE MEASUREMENT OF THE CURVATURE FROM THE CENTER OF THE BODY. 2D AND 1B MODE REPLY21AA051AC20 BPJNJ 04RADIUS,INSIDE,BODY CURVATURE BODY CURVATURE INSIDE RADIUS THE INSIDE MEASUREMENT OF THE CURVATURE FROM THE CENTER OF THE BODY. 2D AND 1B MODE REPLY21AA051AC20 BPJQA 12QUANTITY,LUG,SOLDER SOLDER LUG QUANTITY THE NUMBER OF SOLDER LUGS PROVIDED. 1A MODE REPLY 0 BPJRJ 04WIDTH,SEAT,BUSHING BUSHING SEAT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BUSHING SEAT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BPJSJ 04DIAMETER,SEAT,BUSHING BUSHING SEAT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BUSHING SEAT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BPJTD /D/ 18TYPE FOR WHICH DESIGNED,DUCT DUCT TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF DUCT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BPJWJ 04DIAMETER,NOMINAL,DUCT DUCT NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A DUCT,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BPJXB 04ANGLE IN DEG,TILT TILT ANGLE IN DEG THE ANGLE OF TILT,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BPJYD /D/ 07ACCOMMODATION,FILM,ROLL ROLL FILM ACCOMMODATION AN INDICATION OF WHETHER OR NOT AN ACCOMMODATION FOR ROLL FILM IS INCLUDED. SELECT REPLY CODE 10AA49 BPJZD 08LOCATION,USAGE USAGE LOCATION INDICATES THE LOCATION AT WHICH THE ITEM IS TO BE USED. SELECT REPLY CODE 10AJ91 BPKBD /D/ 07CHEST CHEST AN INDICATION OF WHETHER OR NOT A CHEST IS PROVIDED. SELECT REPLY CODE 10AB22 BPKCJ /D/ 04SIZE ACCOMMODATED,FILM,MAXIMUM MAXIMUM FILM SIZE ACCOMMODATED THE MAXIMUM FILM SIZE THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BPKDD /D/ 07TANK,INSERT INSERT TANK AN INDICATION OF WHETHER OR NOT AN INSERT TANK(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BPKFJ 04HEIGHT,PANEL,BACK BACK PANEL HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BACK PANEL,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BPKGD /D/ 07VALVE,CONTROL,WATER WATER CONTROL VALVE AN INDICATION OF WHETHER OR NOT A WATER CONTROL VALVE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BPKHD /D/ 07VALVE,MIXING,THERMOSTATIC THERMOSTATIC MIXING VALVE AN INDICATION OF WHETHER OR NOT A THERMOSTATIC MIXING VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 BPKJD /D/ 07SAFELIGHT,PANEL,BACK BACK PANEL SAFELIGHT AN INDICATION OF WHETHER OR NOT A BACK PANEL SAFELIGHT IS INCLUDED. SELECT REPLY CODE 10AA49 BPKKD /D/ 07TIMER TIMER AN INDICATION OF WHETHER OR NOT A TIMER IS INCLUDED. SELECT REPLY CODE 10AA49 BPKLD /D/ 07SWITCH,ELECTRICAL ELECTRICAL SWITCH AN INDICATION OF WHETHER OR NOT AN ELECTRICAL SWITCH(ES) IS INCLUDED. SELECT REPLY CODE 10AA49 BPKMD /D/ 07BREAKER,VACUUM VACUUM BREAKER AN INDICATION OF WHETHER OR NOT A VACUUM BREAKER IS INCLUDED. SELECT REPLY CODE 10AA49 BPKND /D/ 07SAFELIGHT,CABINET,INCLOSED INCLOSED CABINET SAFELIGHT AN INDICATION OF WHETHER OR NOT AN INCLOSED CABINET SAFELIGHT IS INCLUDED. SELECT REPLY CODE 10AA49 BPKPD /D/ 07WINDOW,VIEWING VIEWING WINDOW AN INDICATION OF WHETHER OR NOT A VIEWING WINDOW IS INCLUDED. SELECT REPLY CODE 10AA49 BPKQD /D/ 07ARMHOLE,LIGHTPROOF LIGHTPROOF ARMHOLE AN INDICATION OF WHETHER OR NOT A LIGHTPROOF ARMHOLE IS INCLUDED. SELECT REPLY CODE 10AA49 BPKRD /D/ 07SLEEVE SLEEVE AN INDICATION OF WHETHER OR NOT A SLEEVE IS INCLUDED. SELECT REPLY CODE 10AA49 BPKSD /D/ 07BENCH,WORK,INTERNAL INTERNAL WORK BENCH AN INDICATION OF WHETHER OR NOT AN INTERNAL WORK BENCH IS INCLUDED. SELECT REPLY CODE 10AA49 BPKTD /D/ 07UNIT,COOLING COOLING UNIT AN INDICATION OF WHETHER OR NOT A COOLING UNIT IS PROVIDED. SELECT REPLY CODE 10AB22 BPKWG /D/ 19DEVICE AND QUANTITY,CONTROL CONTROL DEVICE AND QUANTITY THE DEVICES THAT CONTROL THE ITEM AND THE NUMBER OF EACH. FULL TEXT WRITE-IN 0 BPKXJ 10CURRENT RATING,OUTPUT,TRANSFORMER TRANSFORMER OUTPUT CURRENT RATING THE OUTPUT CURRENT RATING AT WHICH THE TRANSFORMER IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY11AC30 BPKYJ 10VOLTAGE RATING,PEAK,TRANSFORMER TRANSFORMER PEAK VOLTAGE RATING THE MAXIMUM INSTANTANEOUS VOLTAGE FOR WHICH THE TRANSFORMER IS RATED. 1D AND 1B MODE REPLY11AB63 BPKZD 18TYPE,RECTIFICATION RECTIFICATION TYPE INDICATES THE TYPE OF RECTIFICATION PROVIDED. SELECT REPLY CODE 10AK80 BPLBD 18TYPE,INSERT,TUBE TUBE INSERT TYPE INDICATES THE TYPE OF TUBE INSERT PROVIDED. SELECT REPLY CODE 10AB47 BPLCJ A19FUNCTION AND QUANTITY,WINDING WINDING FUNCTION AND QUANTITY THE PURPOSE AND THE TOTAL NUMBER OF INDIVIDUAL (NOT ELECTRICALLY CONNECTED) WINDINGS DESIGNED TO PERFORM IN A TRANSFORMER. 1D AND 1A MODE REPLY11AC03 BPLDJ /D/ 10VOLTAGE RATING PER FUNCTION,AC,WINDING WINDING AC VOLTAGE RATING PER FUNCTION THE VALUE(S) OF ROOT MEAN SQUARE POTENTIAL PER FUNCTION FOR WHICH THE WINDING IS RATED. 3D AND 1B MODE REPLY31AB631AC202AH19 BPLFJ /D/ 10VOLTAGE RATING PER FUNCTION,DC,WINDING WINDING DC VOLTAGE RATING PER FUNCTION THE VALUE(S) OF DIRECT CURRENT POTENTIAL PER FUNCTION FOR WHICH THE WINDING IS RATED. 3D AND 1B MODE REPLY31AB631AC202AH19 BPLGJ 10CURRENT RATING PER FUNCTION,WINDING WINDING CURRENT RATING PER FUNCTION THE AMOUNT OF CURRENT PER FUNCTION FOR WHICH THE WINDING IS DESIGNED. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 4D AND 1B MODE REPLY41AC301AB621AC202AH19 BPLHJ /D/ 10RESISTANCE RATING PER FUNCTION IN OHMS,DC DC RESISTANCE RATING PER FUNCTION IN OHMS THE OPPOSITION TO THE FLOW OF DIRECT CURRENT PER FUNCTION OFFERED BY AN ITEM,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY12AH19 BPLJJ /D/ 10INDUCTANCE RATING PER FUNCTION INDUCTANCE RATING PER FUNCTION THE VALUE/S/ OF INDUCTANCE PER FUNCTION INHERENT IN THE ITEM. 3D AND 1B MODE REPLY31AC311AC202AH19 BPLKJ /D/ 10IMPEDANCE RATING PER FUNCTION IN OHMS IMPEDANCE RATING PER FUNCTION IN OHMS THE TOTAL OPPOSITION PER FUNCTION /RESISTIVE AND REACTIVE/ WHICH THE ITEM OFFERS TO THE FLOW OF ALTERNATING CURRENT,EXPRESSED IN OHMS. 2D AND 1B MODE REPLY21AC202AH19 BPLLD /D/ 07SHANK,TAPERED TAPERED SHANK AN INDICATION OF WHETHER OR NOT A TAPERED SHANK IS INCLUDED. SELECT REPLY CODE 10AA49 BPLMD 18TYPE,DISK DISK TYPE INDICATES THE TYPE OF DISK. SELECT REPLY CODE 10AK95 BPLNJ 04DIAMETER ACCOMMODATED,MAXIMUM,SANDING PAD SANDING PAD MAXIMUM DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR A SANDING PAD,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BPLPB 10SPEED RATING IN RPM,NO LOAD NO LOAD SPEED RATING IN RPM THE SPEED RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE AT NO LOAD,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 BPLQJ 04LENGTH,TABLE,DISK DISK TABLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A DISK TABLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BPLRJ 04WIDTH,TABLE,DISK DISK TABLE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A DISK TABLE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BPLSB 04ANGLE IN DEG,TILT,DOWNWARD,DISK TABLE DISK TABLE DOWNWARD TILT ANGLE IN DEG THE DOWNWARD TILT ANGLE OF THE DISK TABLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BPLTB 04ANGLE IN DEG,TILT,UPWARD,DISK TABLE DISK TABLE UPWARD TILT ANGLE IN DEG THE UPWARD TILT ANGLE OF THE DISK TABLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BPLWJ 04LENGTH,TABLE,BELT BELT TABLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A BELT TABLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BPLXJ 04WIDTH,TABLE,BELT BELT TABLE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BELT TABLE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BPLYB 04ANGLE TOWARD BELT IN DEG,TILT,TABLE TABLE TILT ANGLE TOWARD BELT IN DEG THE TILT ANGLE OF THE TABLE TOWARD THE BELT,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BPLZB 04ANGLE FROM BELT IN DEG,TILT,TABLE TABLE TILT ANGLE FROM BELT IN DEG THE TILT ANGLE OF THE TABLE AWAY FROM THE BELT,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BPMBD /D/ 07SHANK W/LOCKNUT,THREADED THREADED SHANK W/LOCKNUT AN INDICATION OF WHETHER OR NOT A THREADED SHANK WITH LOCKNUT IS PROVIDED. SELECT REPLY CODE 10AB22 BPMCJ 04DIAMETER,MAXIMUM,BIT SHANK ACCOMMODATED BIT SHANK ACCOMMODATED MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR A BIT SHANK,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BPMDD /D/ 07BIT,BORING BORING BIT AN INDICATION OF WHETHER OR NOT A BORING BIT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BPMFJ 04RADIUS,SWEEP SWEEP RADIUS A MEASUREMENT OF THE DISTANCE FROM THE CENTERLINE TO THE AXIS OF THE SWEEP. 2D AND 1B MODE REPLY21AA051AC20 BPMGL 16STYLE DESIGNATOR,WEDGE WEDGE STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE WEDGE. 1L MODE REPLY 0 BPMHJ 04WIDTH ACROSS FLATS,BLADE BLADE WIDTH ACROSS FLATS THE SHORTEST STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT OF THE BLADE. 2D AND 1B MODE REPLY21AA051AC20 BPMJA 12QUANTITY,END,WORKING WORKING END QUANTITY THE NUMBER OF WORKING ENDS PROVIDED. 1A MODE REPLY 0 BPMKD /D/ 07SCREWDRIVER/WRENCH ON SAME END SCREWDRIVER/WRENCH ON SAME END AN INDICATION OF WHETHER OR NOT A SCREWDRIVER AND WRENCH ARE PROVIDED ON THE SAME END. SELECT REPLY CODE 10AB22 BPMLD /D/ 09MATERIAL,TIP,SCREWDRIVER SCREWDRIVER TIP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SCREWDRIVER TIP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BPMMD /D/ 07TIP,SCREWDRIVER,RECESSED RECESSED SCREWDRIVER TIP AN INDICATION OF WHETHER OR NOT A RECESSED SCREWDRIVER TIP IS PROVIDED. SELECT REPLY CODE 10AB22 BPMND 18TYPE,WRENCH WRENCH TYPE INDICATES THE TYPE OF WRENCH PROVIDED. SELECT REPLY CODE 10AJ57 BPMPG 04SIZE,WRENCH WRENCH SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE WRENCH. FULL TEXT WRITE-IN 0 BPMQD /D/ 07HOOK,ADJUSTMENT,AIR TRIMMER AIR TRIMMER ADJUSTMENT HOOK AN INDICATION OF WHETHER OR NOT AN AIR TRIMMER ADJUSTMENT HOOK IS PROVIDED. SELECT REPLY CODE 10AB22 BPMRD /D/ 07PROVISION,TOOL,POWER DRIVEN POWER DRIVEN TOOL PROVISION AN INDICATION OF WHETHER OR NOT A PROVISION FOR A POWER DRIVEN TOOL/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 BPMSD /D/ 08LOCATION,COVERING,ADDITIONAL INSULATION ADDITIONAL INSULATION COVERING LOCATION THE DESIGNATION OF THAT PART OF AN ITEM TO WHICH ADDITIONAL INSULATION COVERING HAS BEEN APPLIED. SELECT REPLY CODE 10AJ91 BPMTA 03DESIGNATION,SIZE,TIP TIP SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE TIP IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1A MODE REPLY 0 BPMWD /D/ 07SIDE,FLARED FLARED SIDE AN INDICATION OF WHETHER OR NOT A FLARED SIDE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BPMXD 18TYPE,SHANK,DRIVE DRIVE SHANK TYPE INDICATES THE TYPE OF DRIVE SHANK. SELECT REPLY CODE 10AH09 BPMYJ 04SIZE,NOMINAL,DRIVE DRIVE NOMINAL SIZE DESIGNATES THE NOMINAL SIZE OF THE DRIVE,SUCH AS LENGTH,WIDTH,DIAMETER,AND THE LIKE. 1D AND 1B MODE REPLY11AA05 BPMZD 14SHAPE,SOCKET SOCKET SHAPE THE PHYSICAL CONFIGURATION OF THE SOCKET. SELECT REPLY CODE 10AD07 BPNBJ 04DISTANCE ACROSS FLATS,SOCKET SOCKET DISTANCE ACROSS FLATS THE DISTANCE MEASURED ACROSS THE FLATS OF THE SOCKET. 2D AND 1B MODE REPLY21AA051AC20 BPNCB 04ANGLE IN DEG,CHAMFER,HOLE HOLE CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 BPNDJ 04DIAMETER,CHAMFER,HOLE HOLE CHAMFER DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BPNFB 04ANGLE IN DEG,TAPER,SHOULDER SHOULDER TAPER ANGLE IN DEG NONE. 1B MODE REPLY 0 BPNGA 13THREAD SIZE,SHOULDER SHOULDER THREAD SIZE NONE. 1A MODE REPLY 0 BPNHJ 04DIAMETER,MINOR,TAPERED SHOULDER TAPERED SHOULDER MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BPNJJ 04LENGTH,LAYING LAYING LENGTH A MEASUREMENT OF THE LONGEST LAYING DIMENSION OF THE ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BPNKB /D/ 04ANGLE IN DEG,TURN TURN ANGLE IN DEG THE ANGLE FORMED BY THE TURN OF THE ITEM,EXPRESSED IN DEGREES. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. 1B MODE REPLY 0 BPNLD 18TYPE,JOINT,END END JOINT TYPE INDICATES THE TYPE OF END JOINT(S) ON THE ITEM. SELECT REPLY CODE 10AM35 BPNMJ 10STRENGTH,COMPRESSIVE,CONCRETE CONCRETE COMPRESSIVE STRENGTH AN INDICATION OF THE COMPRESSIVE STRENGTH AT WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY12AG67 BPNND /D/ 07COLLAR COLLAR AN INDICATION OF WHETHER OR NOT A COLLAR(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BPNPB 04ANGLE FORMED BY SPUR AND RUN IN DEG ANGLE FORMED BY SPUR AND RUN IN DEG THE ANGLE FORMED BY THE SPUR AND RUN,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BPNQJ 04DIAMETER,INSIDE,RUN RUN INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO SURFACES OF THE RUN,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BPNRJ 04DIAMETER,INSIDE,SPUR SPUR INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO SURFACES OF THE SPUR,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BPNSD /D/ 07VITRIFICATION VITRIFICATION AN INDICATION OF WHETHER OR NOT VITRIFICATION IS PROVIDED. SELECT REPLY CODE 10AB22 BPNTJ /D/ 04LENGTH,RADIUS RADIUS LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE RADIUS OF THE ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BPNWD /D/ 07COUPLING COUPLING AN INDICATION OF WHETHER OR NOT A COUPLING(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BPNXD /D/ 07COUPLING,SNAP SNAP COUPLING AN INDICATION OF WHETHER OR NOT A SNAP COUPLING(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BPNYJ 04LENGTH,COUNTERSINK COUNTERSINK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE COUNTERSINK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BPNZJ /D/ 04SIZE,PIPE,NOMINAL,BITUMINIZED FIBER CONNECTION BITUMINIZED FIBER CONNECTION NOMINAL PIPE SIZE DESIGNATES THE NOMINAL PIPE SIZE OF THE BITUMINIZED FIBER CONNECTION. 1D AND 1B MODE REPLY11AA05 BPPBD /D/ 18TYPE,CONNECTION,ADAPTING END ADAPTING END CONNECTION TYPE INDICATES THE TYPE OF CONNECTION FOR WHICH THE ADAPTING END OF THE ITEM IS DESIGNED. SELECT REPLY CODE 10AB76 BPPCJ /D/ 04SIZE,PIPE,ADAPTING END ADAPTING END PIPE SIZE DESIGNATES THE PIPE SIZE OF THE ADAPTING END. 1D AND 1B MODE REPLY11AA05 BPPDG 19INSCRIPTION,UNIT OF MEASURE,SCALE SCALE UNIT OF MEASURE INSCRIPTION THE STANDARD OF VALUATION AS REPRESENTED BY THE INSCRIPTION. FULL TEXT WRITE-IN 0 BPPFJ 04DIAMETER,OUTSIDE,ACCOMMODATED INLET CONNECTION TUBE ACCOMMODATED INLET CONNECTION TUBE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR AN INLET CONNECTION TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BPPGD 07PROVISION,THREAD,INLET CONNECTION INLET CONNECTION THREAD PROVISION AN INDICATION OF WHETHER OR NOT THE INLET CONNECTION IS THREADED. SELECT REPLY CODE 10AE00 BPPHD 13SCREW THREAD SERIES DESIGNATOR,CONNECTION,OUTLET OUTLET CONNECTION SCREW THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF OUTLET CONNECTION SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 BPPJA 13THREAD CLASS,CONNECTION,OUTLET OUTLET CONNECTION THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL OUTLET CONNECTION THREAD. 1A MODE REPLY 0 BPPKJ T13THREAD PITCH DIAMETER,CONNECTION,OUTLET OUTLET CONNECTION THREAD PITCH DIAMETER THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF AN OUTLET CONNECTION STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 BPPLD 18TYPE,FACILITY,WRENCHING WRENCHING FACILITY TYPE INDICATES THE TYPE OF FACILITY UTILIZED TO ASSEMBLE OR DISASSEMBLE THE ITEM. SELECT REPLY CODE 10AL17 BPPMJ /D/ 04THICKNESS,FLANGE,UNDERCUT UNDERCUT FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BPPNJ 04DIAMETER,BORE,ACCOMMODATED CANNON ACCOMMODATED CANNON BORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE CANNON BORE FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BPPPA 19NUMBER FOR WHICH DESIGNED,MODEL,CANNON CANNON MODEL NUMBER FOR WHICH DESIGNED THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE CANNON FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 BPPQD /D/ 19ARRANGEMENT FOR WHICH DESIGNED,VALVE VALVE ARRANGEMENT FOR WHICH DESIGNED THE VALVE ARRANGEMENT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BPPRD /D/ 07FEATURE,USAGE,SUPERCHARGER SUPERCHARGER USAGE FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM PROVIDES FOR USE OF A SUPERCHARGER. SELECT REPLY CODE 10AB22 BPPSD /D/ 07RECESS,VALVE VALVE RECESS AN INDICATION OF WHETHER OR NOT A VALVE RECESS(ES) IS INCLUDED. SELECT REPLY CODE 10AA49 BPPTD /D/ 07CHAMFER,INSIDE,TOP TOP INSIDE CHAMFER AN INDICATION OF WHETHER OR NOT A TOP INSIDE CHAMFER IS INCLUDED. SELECT REPLY CODE 10AA49 BPPWD /D/ 07CHAMFER,INSIDE,BOTTOM BOTTOM INSIDE CHAMFER AN INDICATION OF WHETHER OR NOT A BOTTOM INSIDE CHAMFER IS INCLUDED. SELECT REPLY CODE 10AA49 BPPXD /D/ 07PORT,INTAKE,TOP TOP INTAKE PORT AN INDICATION OF WHETHER OR NOT A TOP INTAKE PORT IS INCLUDED. SELECT REPLY CODE 10AA49 BPPYJ 04DIAMETER UNDER FLANGE,OUTSIDE,LARGEST LARGEST OUTSIDE DIAMETER UNDER FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BPPZJ 04WIDTH UNDER FLANGE,DIAMETER,OUTSIDE,LARGEST LARGEST OUTSIDE DIAMETER WIDTH UNDER FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BPQBJ 04DIAMETER,OUTSIDE,GROOVED PORTION GROOVED PORTION OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BPQCJ 04WIDTH,PORTION,GROOVED GROOVED PORTION WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BPQDD 18TYPE,FOCUS,TUBE TUBE FOCUS TYPE INDICATES THE TYPE OF TUBE FOCUS PROVIDED. SELECT REPLY CODE 10AH21 BPQFD /D/ 07INSERT,TUBE,SPARE X-RAY SPARE X-RAY TUBE INSERT AN INDICATION OF WHETHER OR NOT A SPARE X-RAY TUBE INSERT IS PROVIDED. SELECT REPLY CODE 10AB22 BPQGA 19CAPACITY,DRYING,FILM HANGER FILM HANGER DRYING CAPACITY THE NUMBER OF FILM HANGER(S) THE ITEM WILL HOLD FOR DRYING. 1A MODE REPLY 0 BPQHB 10TIME IN MINUTES,DRYING DRYING TIME IN MINUTES THE DRYING TIME FOR WHICH THE ITEM IS RATED,EXPRESSED IN MINUTES. 1B MODE REPLY 0 BPQJD /D/ 07FAN,CIRCULATING CIRCULATING FAN AN INDICATION OF WHETHER OR NOT A CIRCULATING FAN IS INCLUDED. SELECT REPLY CODE 10AA49 BPQKD /D/ 07STAND,FOLDING FOLDING STAND AN INDICATION OF WHETHER OR NOT A FOLDING STAND IS INCLUDED. SELECT REPLY CODE 10AA49 BPQLD 08LOCATION,OPENING,DOOR DOOR OPENING LOCATION INDICATES THE LOCATION OF THE DOOR OPENING. SELECT REPLY CODE 10AJ91 BPQMD /D/ 07STOP,PLANE,HORIZONTAL HORIZONTAL PLANE STOP AN INDICATION OF WHETHER OR NOT A HORIZONTAL PLANE STOP IS INCLUDED. SELECT REPLY CODE 10AA49 BPQNJ /D/ 10OPACITY RATING,X-RAY,LINING LINING X-RAY OPACITY RATING THE RATED X-RAY OPACITY OF LINING IN THE ITEM. 1D AND 1B MODE REPLY11AA05 BPQPG 12SIZE AND QUANTITY ACCOMMODATED,PACKAGE,FILM FILM PACKAGE SIZE AND QUANTITY ACCOMMODATED DESIGNATES THE SIZE AND NUMBER OF THE FILM PACKAGE(S) THE ITEM WILL ACCOMMODATE. FULL TEXT WRITE-IN 0 BPQQA /D/ 12QUANTITY,STOP,FILM STORAGE BIN FILM STORAGE BIN STOP QUANTITY THE NUMBER OF STOP(S) PROVIDED IN THE FILM STORAGE BIN. 1A MODE REPLY 0 BPQRD 18TYPE,HEATER HEATER TYPE INDICATES THE TYPE OF HEATER PROVIDED. SELECT REPLY CODE 10AB04 BPQSA 12QUANTITY,HEATER HEATER QUANTITY THE NUMBER OF HEATER(S) PROVIDED. 1A MODE REPLY 0 BPQTA 12QUANTITY ACCOMMODATED PER DRAWER,HANGER,FILM FILM HANGER QUANTITY ACCOMMODATED PER DRAWER THE NUMBER OF FILM HANGER(S) ACCOMMODATED IN EACH DRAWER. 1A MODE REPLY 0 BPQWD 18TYPE,SUSPENSION SUSPENSION TYPE INDICATES THE TYPE OF SUSPENSION PROVIDED. SELECT REPLY CODE 10AK54 BPQXD 08LOCATION,FAN,EXHAUST EXHAUST FAN LOCATION INDICATES THE LOCATION OF THE EXHAUST FAN. SELECT REPLY CODE 10AJ91 BPQYJ 10CAPACITY,AIR AIR CAPACITY THE RATED AIR CAPACITY PASSED THROUGH THE ITEM. 1D AND 1B MODE REPLY12AG67 BPQZD /D/ 07FEATURE,COUNTERSUNK COUNTERSUNK FEATURE AN INDICATION OF WHETHER OR NOT A COUNTERSUNK FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BPRBD /D/ 07SWITCH,IDENTIFIED IDENTIFIED SWITCH AN INDICATION OF WHETHER OR NOT AN IDENTIFIED SWITCH/ES/ IS PROVIDED. SELECT REPLY CODE 10AB22 BPRCD /D/ 07FEATURE,INTERLOCKED W/FAN,HEATER HEATER INTERLOCKED W/FAN FEATURE AN INDICATION OF WHETHER OR NOT A HEATER INTERLOCKED WITH FAN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BPRDD /D/ 07COMPARTMENT,STORAGE,CASSETTE SPARE CASSETTE SPARE STORAGE COMPARTMENT AN INDICATION OF WHETHER OR NOT A CASSETTE SPARE STORAGE COMPARTMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BPRFA /D/ 12QUANTITY ACCOMMODATED,CASSETTE CASSETTE QUANTITY ACCOMMODATED THE NUMBER OF CASSETTE(S) ACCOMMODATED BY THE ITEM. 1A MODE REPLY 0 BPRGG /D/ 04SIZE ACCOMMODATED,CASSETTE,SPARE COMPARTMENT SPARE COMPARTMENT CASSETTE SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE CASSETTE THE SPARE COMPARTMENT WILL ACCOMMODATE. FULL TEXT WRITE-IN 0 BPRHD /D/ 07COMPARTMENT,STORAGE,ACCESSORY ACCESSORY STORAGE COMPARTMENT AN INDICATION OF WHETHER OR NOT AN ACCESSORY STORAGE COMPARTMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BPRJD /D/ 07TIMER,AUTOMATIC AUTOMATIC TIMER AN INDICATION OF WHETHER OR NOT AN AUTOMATIC TIMER IS INCLUDED. SELECT REPLY CODE 10AA49 BPRKD /D/ 08LOCATION,LEAF,DROP DROP LEAF LOCATION INDICATES THE LOCATION OF THE DROP LEAF(VES). SELECT REPLY CODE 10AJ91 BPRLD 04SIZE FOR WHICH DESIGNED,AMMUNITION AMMUNITION SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE AMMUNITION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AF81 BPRMJ 10SPACING BETWEEN FLIGHTS SPACING BETWEEN FLIGHTS THE SPACING BETWEEN FLIGHTS. 2D AND 1B MODE REPLY21AA051AC20 BPRND 11METHOD,OPERATION,MANUAL MANUAL OPERATION METHOD THE MEANS USED TO MANUALLY OPERATE THE ITEM. SELECT REPLY CODE 10AC58 BPRPA 19NAME,MANUFACTURER,MAIN HYDRAULIC PUMPING UNIT MAIN HYDRAULIC PUMPING UNIT MANUFACTURER NAME THE NAME OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE MAIN HYDRAULIC PUMPING UNIT. 1A MODE REPLY 0 BPRQG 03DESIGNATOR,IDENTIFICATION,HYDRAULIC PUMP,MAIN MAIN HYDRAULIC PUMP IDENTIFICATION DESIGNATOR A DESIGNATION ASSIGNED TO THE MAIN HYDRAULIC PUMP FOR THE PURPOSE OF READY IDENTIFICATION. FULL TEXT WRITE-IN 0 BPRRD /D/ 07MOTOR,HYDRAULIC HYDRAULIC MOTOR AN INDICATION OF WHETHER OR NOT A HYDRAULIC MOTOR IS INCLUDED. SELECT REPLY CODE 10AA49 BPRSD 11METHOD,OPERATION,BRAKE BRAKE OPERATION METHOD THE MEANS USED TO ACTIVATE THE BRAKE. SELECT REPLY CODE 10AC58 BPRTD /D/ 07SWITCH,INTERLOCK,CONTROL CONTROL INTERLOCK SWITCH AN INDICATION OF WHETHER OR NOT A CONTROL INTERLOCK SWITCH/ES/ IS INCLUDED. SELECT REPLY CODE 10AA49 BPRWD 11METHOD,REMOVING,MOISTURE MOISTURE REMOVING METHOD THE MEANS USED TO REMOVE MOISTURE FROM THE ITEM. SELECT REPLY CODE 10AN37 BPRXH /D/ 01COLOR AND LOCATION,LENS LENS COLOR AND LOCATION THE HUE OR TINT OF THE LENS AND ITS LOCATION. 2D MODE REPLY 26AD063AJ91 BPRYD /D/ 07ROLLER,PUSH PUSH ROLLER AN INDICATION OF WHETHER OR NOT A PUSH ROLLER(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BPRZD 18TYPE,DEVICE,SAFETY SAFETY DEVICE TYPE INDICATES THE TYPE OF SAFETY DEVICE(S) PROVIDED. SELECT REPLY CODE 10AM97 BPSBJ /D/ 04WIDTH,LARGEST LARGEST WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE LARGEST PORTION OF AN ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BPSCD 11METHOD,ACTUATION,BOOM BOOM ACTUATION METHOD THE MEANS BY WHICH THE BOOM IS ACTUATED. SELECT REPLY CODE 10AC58 BPSDJ 10AMOUNT,RESIN RESIN AMOUNT THE AMOUNT OF RESIN PROVIDED. 2D AND 1B MODE REPLY22AG671AC20 BPSFD /D/ 07MARKINGS,GRID GRID MARKINGS AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES GRID MARKINGS. SELECT REPLY CODE 10AA49 BPSGD 19POSITION,SPINDLE SPINDLE POSITION THE POSITION OF THE SPINDLE ON THE ITEM. SELECT REPLY CODE 10AK54 BPSHJ 10AREA,FILTERING FILTERING AREA DESIGNATES THE SIZE OF THE FILTERING AREA. 2D AND 1B MODE REPLY22AG671AC20 BPSJD /D/ 07FEATURE,MOUNTED,RIM RIM MOUNTED FEATURE AN INDICATION OF WHETHER OR NOT A RIM MOUNTED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BPSKJ 04LENGTH,SURFACE,WORK WORK SURFACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A WORK SURFACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BPSLA 12QUANTITY ACCOMMODATED,TUBE,TEST TEST TUBE QUANTITY ACCOMMODATED THE NUMBER OF TEST TUBES THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 BPSMJ 04WIDTH,SURFACE,WORK WORK SURFACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A WORK SURFACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BPSND /D/ 07CUSHION,RUBBER RUBBER CUSHION AN INDICATION OF WHETHER OR NOT A RUBBER CUSHION(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BPSPJ 10TRAVEL,LONGITUDINAL,WORK SURFACE WORK SURFACE LONGITUDINAL TRAVEL THE LONGITUDINAL DISTANCE THE WORK SURFACE WILL TRAVEL. 2D AND 1B MODE REPLY21AA051AC20 BPSQJ 10TRAVEL,CROSS,WORK SURFACE WORK SURFACE CROSS TRAVEL THE DISTANCE THE WORK SURFACE WILL EXTEND FROM ONE SIDE TO THE OTHER. 2D AND 1B MODE REPLY21AA051AC20 BPSRJ 04DIAMETER,SURFACE,WORK WORK SURFACE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A WORK SURFACE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BPSSJ 10ADJUSTMENT,VERTICAL,WORK SURFACE WORK SURFACE VERTICAL ADJUSTMENT THE MEASURED DISTANCE THE WORK SURFACE CAN BE ADJUSTED VERTICALLY. 2D AND 1B MODE REPLY21AA051AC20 BPSTD 11METHOD,FEED,WORK SURFACE WORK SURFACE FEED METHOD THE MEANS BY WHICH MATERIALS ARE FED TO THE WORK SURFACE. SELECT REPLY CODE 10AG25 BPSWD 19DEVICE,HOLDING,WORK WORK HOLDING DEVICE THE DEVICE USED TO HOLD THE WORK IN PLACE. SELECT REPLY CODE 10AJ27 BPSXJ 10ADJUSTMENT,VERTICAL,HEAD HEAD VERTICAL ADJUSTMENT THE MEASURED DISTANCE THE HEAD CAN BE ADJUSTED VERTICALLY. 2D AND 1B MODE REPLY21AA051AC20 BPSYJ 10TRAVEL,CROSS,HEAD HEAD CROSS TRAVEL THE DISTANCE THE HEAD WILL EXTEND FROM ONE SIDE TO THE OTHER. 2D AND 1B MODE REPLY21AA051AC20 BPSZD 18TYPE,FEED,HEAD HEAD FEED TYPE INDICATES THE TYPE OF HEAD FEED PROVIDED. SELECT REPLY CODE 10AG25 BPTBJ /D/ 04DISTANCE FROM SPINDLE CENTER/END TO WORK SURFACE TOP,MAXIMUM MAXIMUM DISTANCE FROM SPINDLE CENTER/END TO WORK SURFACE TOP THE MAXIMUM DISTANCE FROM THE CENTER OR END OF THE SPINDLE TO THE TOP OF THE WORK SURFACE. 1D AND 1B MODE REPLY11AA05 BPTCD 07REMOVABILITY,TIP,SPOUT SPOUT TIP REMOVABILITY AN INDICATION OF WHETHER OR NOT THE SPOUT TIP IS REMOVABLE. SELECT REPLY CODE 10AC29 BPTDJ 10STROKE,MAXIMUM MAXIMUM STROKE THE MAXIMUM STROKE OF THE ITEM. 1D AND 1B MODE REPLY11AA05 BPTFJ 04DIAMETER,HOLE,MAXIMUM,GRINDING CAPABILITY GRINDING CAPABILITY MAXIMUM HOLE DIAMETER THE MAXIMUM HOLE DIAMETER THE ITEM IS CAPABLE OF GRINDING. 1D AND 1B MODE REPLY11AA05 BPTGD 18TYPE FOR WHICH DESIGNED,BLADE,SAW SAW BLADE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF SAW BLADE(S) FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AJ02 BPTHJ 04WIDTH ACCOMMODATED,BLADE,MINIMUM MINIMUM BLADE WIDTH ACCOMMODATED THE MINIMUM BLADE WIDTH THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BPTJJ /D/ 04WIDTH ACCOMMODATED,BLADE,MAXIMUM MAXIMUM BLADE WIDTH ACCOMMODATED THE MAXIMUM BLADE WIDTH THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BPTKJ 10MEASUREMENT,SCALE SCALE MEASUREMENT THE MEASUREMENT THE SCALE IS DESIGNED TO INDICATE. 2D AND 1B MODE REPLY21AA051AC20 BPTLJ 04DIAMETER ACCOMMODATED,BLADE,MINIMUM MINIMUM BLADE DIAMETER ACCOMMODATED THE MINIMUM BLADE DIAMETER THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BPTMJ 04DIAMETER ACCOMMODATED,MAXIMUM,BLADE BLADE MAXIMUM DIAMETER ACCOMMODATED THE MAXIMUM BLADE DIAMETER THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BPTNJ T04DIAMETER RANGE ACCCOMMODATED,ARBOR HOLE,BLADE BLADE ARBOR HOLE DIAMETER RANGE ACCOMMODATED THE DIAMETER RANGE OF BLADE ARBOR HOLES THE ITEM WILL ACCOMMODATE. 1D AND 1F MODE REPLY11AA05 BPTPJ 04DIAMETER,MAXIMUM,ABRASIVE WHEEL ABRASIVE WHEEL MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ABRASIVE WHEEL,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BPTQJ 04THICKNESS,MAXIMUM,ABRASIVE WHEEL ABRASIVE WHEEL MAXIMUM THICKNESS THE MAXIMUM MEASUREMENT OF THE SMALLEST DIMENSION OF THE ABRASIVE WHEEL,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 BPTRJ T04DIAMETER RANGE ACCOMMODATED DIAMETER RANGE ACCOMMODATED THE RANGE OF DIAMETERS THE ITEM WILL ACCOMMODATE. 1D AND 1F MODE REPLY11AA05 BPTSA 12QUANTITY ACCOMMODATED,FLUTE FLUTE QUANTITY ACCOMMODATED THE NUMBER OF FLUTES THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 BPTTJ /D/A18TYPE AND QUANTITY,SHELF SHELF TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF SHELVES PROVIDED. 1D AND 1A MODE REPLY12AG37 BPTWF T04ANGLE ADJUSTMENT RANGE ACCOMMODATED IN DEG ANGLE ADJUSTMENT RANGE ACCOMMODATED IN DEG THE ANGLE ADJUSTMENT RANGE THE ITEM WILL ACCOMMODATE,EXPRESSED IN DEGREES. 1F MODE REPLY 0 BPTXJ /D/T04SIZE AND TYPE ACCOMMODATED,UNIT UNIT SIZE AND TYPE ACCOMMODATED DESIGNATES THE SIZE AND TYPE OF THE ACCOMMODATED UNIT. 2D AND 1F MODE REPLY21AA052AG37 BPTZJ 04WIDTH,FACE,WHEEL WHEEL FACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A WHEEL FACE FROM SIDE TO SIDE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BPWBJ 04DIAMETER,HOLE,WHEEL MOUNTING WHEEL MOUNTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A WHEEL MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BPWCD 11METHOD,GRINDING GRINDING METHOD THE MEANS USED FOR GRINDING. SELECT REPLY CODE 10AF75 BPWDJ 04THICKNESS AT BASE,FLANGE,LEFT LEFT FLANGE THICKNESS AT BASE NONE. 2D AND 1B MODE REPLY21AA051AC20 BPWFJ 04THICKNESS AT BASE,FLANGE,RIGHT RIGHT FLANGE THICKNESS AT BASE NONE. 2D AND 1B MODE REPLY21AA051AC20 BPWGJ /D/ 04RADIUS WHERE END FLANGE JOINS TOP FLANGE,CORNER,LEFT SIDE INNER LEFT SIDE INNER CORNER RADIUS WHERE END FLANGE JOINS TOP FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BPWHJ /D/ 04RADIUS WHERE END FLANGE JOINS TOP FLANGE,CORNER,LEFT SIDE OUTER LEFT SIDE OUTER CORNER RADIUS WHERE END FLANGE JOINS TOP FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BPWJJ /D/ 04HEIGHT,TOP,LEFT SIDE FLANGE LEFT SIDE FLANGE TOP HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BPWKJ /D/ 04HEIGHT,TOP,RIGHT SIDE FLANGE RIGHT SIDE FLANGE TOP HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BPWLJ /D/ 04LENGTH,TAPER,INNER,LEFT SIDE BASE FLANGE LEFT SIDE BASE FLANGE INNER TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BPWMJ /D/ 04LENGTH,TAPER,OUTER,LEFT SIDE BASE FLANGE LEFT SIDE BASE FLANGE OUTER TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BPWNJ /D/ 04LENGTH,TAPER,INNER,RIGHT SIDE BASE FLANGE RIGHT SIDE BASE FLANGE INNER TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BPWPJ /D/ 04LENGTH,TAPER,OUTER,RIGHT SIDE BASE FLANGE RIGHT SIDE BASE FLANGE OUTER TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BPWQJ /D/ 04THICKNESS,TIP,LEFT SIDE BASE FLANGE LEFT SIDE BASE FLANGE TIP THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BPWRJ /D/ 04THICKNESS,TIP,RIGHT SIDE BASE FLANGE RIGHT SIDE BASE FLANGE TIP THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BPWSJ /D/ 04RADIUS,TIP,RIGHT SIDE BASE FLANGE RIGHT SIDE BASE FLANGE TIP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BPWTJ /D/ 04RADIUS,TIP,LEFT SIDE BASE FLANGE LEFT SIDE BASE FLANGE TIP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BPWWJ /D/ 04RADIUS AT TOE,INNER SIDE,RIGHT SIDE BASE FLANGE RIGHT SIDE BASE FLANGE INNER SIDE RADIUS AT TOE NONE. 2D AND 1B MODE REPLY21AA051AC20 BPWXJ /D/ 04RADIUS AT TOE,OUTER SIDE,RIGHT SIDE BASE FLANGE RIGHT SIDE BASE FLANGE OUTER SIDE RADIUS AT TOE NONE. 2D AND 1B MODE REPLY21AA051AC20 BPWYJ /D/ 04RADIUS AT TOE,INNER SIDE,LEFT SIDE BASE FLANGE LEFT SIDE BASE FLANGE INNER SIDE RADIUS AT TOE NONE. 2D AND 1B MODE REPLY21AA051AC20 BPWZJ /D/ 04RADIUS AT TOE,OUTER SIDE,LEFT SIDE BASE FLANGE LEFT SIDE BASE FLANGE OUTER SIDE RADIUS AT TOE NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXBJ /D/ 04RADIUS OF FILLET AT BULB,FLANGE,BOTTOM,LEFT SIDE LEFT SIDE BOTTOM FLANGE RADIUS OF FILLET AT BULB NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXCJ /D/ 04RADIUS OF FILLET AT BULB,FLANGE,BOTTOM,RIGHT SIDE RIGHT SIDE BOTTOM FLANGE RADIUS OF FILLET AT BULB NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXDJ 04DISTANCE TO CENTER OF BOTH FLANGES,FLANGE,TOP,LEFT SIDE LEFT SIDE TOP FLANGE DISTANCE TO CENTER OF BOTH FLANGES NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXFJ 04DISTANCE TO CENTER OF BOTH FLANGES,FLANGE,BOTTOM,LEFT SIDE LEFT SIDE BOTTOM FLANGE DISTANCE TO CENTER OF BOTH FLANGES NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXGJ 04DISTANCE TO CENTER OF BOTH FLANGES,FLANGE,TOP,RIGHT SIDE RIGHT SIDE TOP FLANGE DISTANCE TO CENTER OF BOTH FLANGES NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXHJ 04DISTANCE TO CENTER OF BOTH FLANGES,FLANGE,BOTTOM,RIGHT SIDE RIGHT SIDE BOTTOM FLANGE DISTANCE TO CENTER OF BOTH FLANGES NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXJJ 04RADIUS WHERE TOP LEFT FLANGE JOINS WEB FLANGE/LEG,FILLET FILLET RADIUS WHERE TOP LEFT FLANGE JOINS WEB FLANGE/LEG NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXKJ 04RADIUS WHERE BOTTOM LEFT FLANGE JOINS WEB FLANGE/LEG,FILLET FILLET RADIUS WHERE BOTTOM LEFT FLANGE JOINS WEB FLANGE/LEG NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXLJ 04RADIUS WHERE TOP RIGHT FLANGE JOINS WEB FLANGE/LEG,FILLET FILLET RADIUS WHERE TOP RIGHT FLANGE JOINS WEB FLANGE/LEG NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXMJ 04RADIUS WHERE BOTTOM RIGHT FLANGE JOINS WEB FLANGE/LEG,FILLET FILLET RADIUS WHERE BOTTOM RIGHT FLANGE JOINS WEB FLANGE/LEG NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXNJ 04THICKNESS,FLANGE,WEB WEB FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXPJ /D/ 04DIAMETER,BOTTOM,LEFT SIDE FLANGE LEFT SIDE FLANGE BOTTOM DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXQJ /D/ 04DIAMETER,BOTTOM,RIGHT SIDE FLANGE RIGHT SIDE FLANGE BOTTOM DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXRJ /D/ 04RADIUS,OUTER,LEFT SIDE FLANGE BOTTOM LEFT SIDE FLANGE BOTTOM OUTER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXSJ /D/ 04RADIUS,INNER,LEFT SIDE FLANGE BOTTOM LEFT SIDE FLANGE BOTTOM INNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXTJ /D/ 04RADIUS,INNER,RIGHT SIDE FLANGE BOTTOM RIGHT SIDE FLANGE BOTTOM INNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXWJ /D/ 04RADIUS,OUTER,RIGHT SIDE FLANGE BOTTOM RIGHT SIDE FLANGE BOTTOM OUTER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXXJ /D/ 04RADIUS,BOTTOM,RIGHT SIDE FLANGE RIGHT SIDE FLANGE BOTTOM RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BPXYB /D/ 04ANGLE IN DEG,INSIDE,LEFT TOP LEFT TOP INSIDE ANGLE IN DEG NONE. 1B MODE REPLY 0 BPXZB /D/ 04ANGLE IN DEG,INSIDE,LEFT BOTTOM LEFT BOTTOM INSIDE ANGLE IN DEG NONE. 1B MODE REPLY 0 BPYBB /D/ 04ANGLE IN DEG,INSIDE,RIGHT TOP RIGHT TOP INSIDE ANGLE IN DEG NONE. 1B MODE REPLY 0 BPYCB /D/ 04ANGLE IN DEG,INSIDE,RIGHT BOTTOM RIGHT BOTTOM INSIDE ANGLE IN DEG NONE. 1B MODE REPLY 0 BPYDJ 04LENGTH,MINOR MINOR LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BPYFJ 04WIDTH,SECTION,DISPLAY DISPLAY SECTION WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A DISPLAY SECTION,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BPYGJ 04HEIGHT,SECTION,DISPLAY DISPLAY SECTION HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE DISPLAY SECTION,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BPYHJ 04DEPTH,SECTION,DISPLAY DISPLAY SECTION DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON A DISPLAY SECTION,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BPYJA 12QUANTITY,SHELF,DISPLAY SECTION DISPLAY SECTION SHELF QUANTITY THE NUMBER OF DISPLAY SECTION SHELVES PROVIDED WITH THE ITEM. 1A MODE REPLY 0 BPYKD /D/ 09MATERIAL,SHELF SHELF MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHELF IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BPYLA 12QUANTITY,DOOR,DISPLAY SECTION DISPLAY SECTION DOOR QUANTITY THE NUMBER OF DISPLAY SECTION DOORS PROVIDED WITH THE ITEM. 1A MODE REPLY 0 BPYMA 12QUANTITY,WING WING QUANTITY THE NUMBER OF WINGS PROVIDED WITH THE ITEM. 1A MODE REPLY 0 BPYNJ 04WIDTH,WING WING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A WING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BPYPJ 04WIDTH,SURFACE,POSTING POSTING SURFACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE POSTING SURFACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BPYQD /D/ 07SLOTS,INSERT,POSTING SURFACE POSTING SURFACE INSERT SLOTS AN INDICATION OF WHETHER OR NOT INSERT SLOTS ARE INCLUDED ON THE POSTING SURFACE. SELECT REPLY CODE 10AA49 BPYRJ 04DISTANCE BETWEEN SLOTS DISTANCE BETWEEN SLOTS THE DISTANCE BETWEEN THE SLOTS ON THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BPYSJ 04HEIGHT,SURFACE,POSTING POSTING SURFACE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE POSTING SURFACE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BPYTD 18TYPE,FACE,POSTING SURFACE POSTING SURFACE FACE TYPE INDICATES THE TYPE OF POSTING SURFACE FACE PROVIDED. SELECT REPLY CODE 10AG89 BPYWD 11METHOD,HANGING HANGING METHOD THE MEANS BY WHICH THE ITEM IS HUNG. SELECT REPLY CODE 10AB47 BPYXD /D/ 07FEATURE,RULED RULED FEATURE AN INDICATION OF WHETHER OR NOT A RULED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BPYYD /D/ 07TROUGH,ERASER ERASER TROUGH AN INDICATION OF WHETHER OR NOT AN ERASER TROUGH IS PROVIDED. SELECT REPLY CODE 10AB22 BPYZA 12QUANTITY PER HORIZONTAL ROW,LOCKER LOCKER QUANTITY PER HORIZONTAL ROW THE NUMBER OF LOCKERS IN A HORIZONTAL ROW. 1A MODE REPLY 0 BPZBA 12QUANTITY,LOCKER,INDIVIDUAL INDIVIDUAL LOCKER QUANTITY THE NUMBER OF INDIVIDUAL LOCKERS PROVIDED. 1A MODE REPLY 0 BPZCJ 04WIDTH,LOCKER,INDIVIDUAL INDIVIDUAL LOCKER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE INDIVIDUAL LOCKER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BPZDJ 04DEPTH,LOCKER,INDIVIDUAL INDIVIDUAL LOCKER DEPTH THE MEASUREMENT BETWEEN SPECIFIED POINTS ON THE INDIVIDUAL LOCKER,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BPZFJ 04HEIGHT,LOCKER,INDIVIDUAL INDIVIDUAL LOCKER HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE INDIVIDUAL LOCKER,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BPZGD 18TYPE,VENTILATION,DOOR DOOR VENTILATION TYPE INDICATES THE TYPE OF DOOR VENTILATION PROVIDED. SELECT REPLY CODE 10AC53 BPZHG /D/ 19EQUIPMENT AND QUANTITY,INTERIOR,INDIVIDUAL LOCKER INDIVIDUAL LOCKER INTERIOR EQUIPMENT AND QUANTITY THE NAME AND NUMBER OF INTERIOR EQUIPMENT FURNISHED WITH THE INDIVIDUAL LOCKER. FULL TEXT WRITE-IN 0 BPZJD /D/ 17SURFACE TREATMENT,TOP TOP SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE TOP SURFACE. SELECT REPLY CODE 10AD09 BPZKD /D/ 07COVER,TOP,REMOVABLE REMOVABLE TOP COVER AN INDICATION OF WHETHER OR NOT A REMOVABLE TOP COVER IS INCLUDED. SELECT REPLY CODE 10AA49 BPZLD /D/ 07FEATURE,MARBLEIZED MARBLEIZED FEATURE AN INDICATION OF WHETHER OR NOT A MARBLEIZED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BPZMD /D/ 01COLOR,MARBLED MARBLED COLOR THE HUE OR TINT OF THE MARBLED PORTION OF THE ITEM. SELECT REPLY CODE 10AD06 BPZND /D/ 07RAIL,TOP TOP RAIL AN INDICATION OF WHETHER OR NOT A TOP RAIL IS INCLUDED. SELECT REPLY CODE 10AA49 BPZPD /D/ 07TOP,ELEVATED ELEVATED TOP AN INDICATION OF WHETHER OR NOT AN ELEVATED TOP IS INCLUDED. SELECT REPLY CODE 10AA49 BPZQD /D/ 07DOOR,COMPARTMENT COMPARTMENT DOOR AN INDICATION OF WHETHER OR NOT A COMPARTMENT DOOR(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BPZRA 12QUANTITY,SHELF,COMPARTMENT COMPARTMENT SHELF QUANTITY THE NUMBER OF SHELVES FURNISHED IN THE COMPARTMENT. 1A MODE REPLY 0 BPZSD 18TYPE,RACK,COMPARTMENT COMPARTMENT RACK TYPE INDICATES THE TYPE OF COMPARTMENT RACK PROVIDED. SELECT REPLY CODE 10AG60 BPZTD /D/ 07RACK,BASIN BASIN RACK AN INDICATION OF WHETHER OR NOT A BASIN RACK IS INCLUDED. SELECT REPLY CODE 10AA49 BPZWD /D/ 07BAR,TOWEL TOWEL BAR AN INDICATION OF WHETHER OR NOT A TOWEL BAR IS INCLUDED. SELECT REPLY CODE 10AA49 BPZXD /D/ 09MATERIAL,SURFACE,WORK WORK SURFACE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WORK SURFACE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BPZYJ 04HEIGHT ABOVE FLOOR,SURFACE,WORK WORK SURFACE HEIGHT ABOVE FLOOR A MEASUREMENT OF THE HEIGHT OF THE WORK SURFACE ABOVE THE FLOOR. 2D AND 1B MODE REPLY21AA051AC20 BPZZD /D/ 07STOP,BACK BACK STOP AN INDICATION OF WHETHER OR NOT A BACK STOP IS INCLUDED. SELECT REPLY CODE 10AA49 BQBBA 12QUANTITY ACCOMMODATED,HANGER HANGER QUANTITY ACCOMMODATED THE NUMBER OF HANGERS THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 BQBCA 12QUANTITY,SHELF,HAT HAT SHELF QUANTITY THE NUMBER OF HAT SHELVES FURNISHED WITH THE ITEM. 1A MODE REPLY 0 BQBDJ 04DEPTH,RADIUS,GROOVE GROOVE RADIUS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BQBFD /D/ 07HOLE,INTAKE INTAKE HOLE AN INDICATION OF WHETHER OR NOT AN INTAKE HOLE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BQBGJ 04DISTANCE BETWEEN ROWS,CENTER TO CENTER,HOLE HOLE CENTER TO CENTER DISTANCE BETWEEN ROWS THE HOLE CENTER TO CENTER DISTANCE BETWEEN ROWS. 2D AND 1B MODE REPLY21AA051AC20 BQBHA 12QUANTITY PER ROW,HOLE HOLE QUANTITY PER ROW THE NUMBER OF HOLES IN EACH ROW. 1A MODE REPLY 0 BQBJJ 04DISTANCE FROM TOP TO CENTER OF FIRST ROW DISTANCE FROM TOP TO CENTER OF FIRST ROW THE DISTANCE FROM THE TOP OF THE ITEM TO THE CENTER OF THE FIRST ROW. 2D AND 1B MODE REPLY21AA051AC20 BQBKJ 04DEPTH,CLEARANCE,ROD,CONNECTING CONNECTING ROD CLEARANCE DEPTH A MEASUREMENT OF THE CONNECTING ROD CLEARANCE DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BQBLD /D/ 07GROOVE,CARBON CARBON GROOVE AN INDICATION OF WHETHER OR NOT A CARBON GROOVE IS INCLUDED. SELECT REPLY CODE 10AA49 BQBMA /D/ 16STYLE,END,PISTON CONNECTING PISTON CONNECTING END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PISTON CONNECTING END. 1A MODE REPLY 0 BQBNJ 04RADIUS,EDGE EDGE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQBPJ 04DIAMETER,INSIDE,END HOLE END HOLE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BQBQJ 04DIAMETER,HOLE,ANCHOR,PISTON PIN PISTON PIN ANCHOR HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BQBRJ /D/ 04DEPTH,HOLE,CENTERLINE TO FORK CENTERLINE TO FORK HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BQBSB 04ANGLE BETWEEN ANCHOR PIN HOLE AND ROD CENTERLINES IN DEG ANGLE BETWEEN ANCHOR PIN HOLE AND ROD CENTERLINES IN DEG NONE. 1B MODE REPLY 0 BQBTD /D/ 07BEARING,END,PISTON CONNECTING PISTON CONNECTING END BEARING AN INDICATION OF WHETHER OR NOT A PISTON CONNECTING END BEARING IS INCLUDED. SELECT REPLY CODE 10AA49 BQBWD 07REPLACEABILITY,BEARING BEARING REPLACEABILITY AN INDICATION OF WHETHER OR NOT THE BEARING IS REPLACEABLE. SELECT REPLY CODE 10AG84 BQBXA /D/ 16STYLE,END,SHAFT CONNECTING SHAFT CONNECTING END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SHAFT CONNECTING END. 1A MODE REPLY 0 BQBYD /D/ 07FEATURE,DRILL,PISTON CONNECTING END LUBRICATION PISTON CONNECTING END LUBRICATION DRILL FEATURE AN INDICATION OF WHETHER OR NOT A DRILL FEATURE FOR LUBRICATION PURPOSES IS INCLUDED WITH THE PISTON CONNECTING END. SELECT REPLY CODE 10AA49 BQBZD 11METHOD,LUBRICATION,PISTON CONNECTING END PISTON CONNECTING END LUBRICATION METHOD THE MEANS USED TO LUBRICATE THE PISTON CONNECTING END. SELECT REPLY CODE 10AB75 BQCBD /D/ 07BEARING,END,SHAFT CONNECTING SHAFT CONNECTING END BEARING AN INDICATION OF WHETHER OR NOT A SHAFT CONNECTING END BEARING IS INCLUDED. SELECT REPLY CODE 10AA49 BQCCJ 04DIAMETER,INSIDE,SHAFT CONNECTING END HOLE SHAFT CONNECTING END HOLE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SHAFT CONNECTING END HOLE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BQCDJ /D/ 04RADIUS,CORNER,SHAFT CONNECTING END SHAFT CONNECTING END CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQCFJ 04RADIUS,EDGE,SHAFT CONNECTING END SHAFT CONNECTING END EDGE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQCGJ 04WIDTH,END,SHAFT CONNECTING SHAFT CONNECTING END WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BQCHJ 04THICKNESS,END,SHAFT CONNECTING SHAFT CONNECTING END THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQCJJ /D/ 04DEPTH,SHAFT CONNECTING END HOLE CENTERLINE TO FORK SHAFT CONNECTING END HOLE CENTERLINE TO FORK DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BQCKJ 04LENGTH,FORK,SHAFT CONNECTING END SHAFT CONNECTING END FORK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BQCLJ /D/ 04WIDTH,SPAN,FORK,SHAFT CONNECTING END SHAFT CONNECTING END FORK SPAN WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BQCMJ /D/ 04DIAMETER,CIRCLE,HOLE,SHAFT CONNECTING END KNUCKLE PIN SHAFT CONNECTING END KNUCKLE PIN HOLE CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BQCNA 12QUANTITY,HOLE,PIN,SHAFT CONNECTING END KNUCKLE SHAFT CONNECTING END KNUCKLE PIN HOLE QUANTITY NONE. 1A MODE REPLY 0 BQCPJ /D/ 04DIAMETER,HOLE,SHAFT CONNECTING END KNUCKLE PIN SHAFT CONNECTING END KNUCKLE PIN HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BQCQJ 04LENGTH,MAJOR,TAPER TAPER MAJOR LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BQCRJ /D/ 04DISTANCE BETWEEN THIRD AND FOURTH MOUNTING HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN THIRD AND FOURTH MOUNTING HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BQCSJ /D/ 04DISTANCE BETWEEN HOLE CENTERS,SECOND SECOND DISTANCE BETWEEN HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQCTJ 04DIAMETER,HOLE,TOP TOP HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BQCWJ 04DIAMETER,HOLE,BOTTOM BOTTOM HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BQCXB /D/ 04ANGLE IN DEG,SHANK,REAR REAR SHANK ANGLE IN DEG NONE. 1B MODE REPLY 0 BQCYD 07REPLACEABILITY,BEARING,SHAFT CONNECTING END SHAFT CONNECTING END BEARING REPLACEABILITY AN INDICATION OF WHETHER OR NOT THE SHAFT CONNECTING END BEARING IS REPLACEABLE. SELECT REPLY CODE 10AG84 BQCZD /D/ 07FEATURE,DRILL,SHAFT CONNECTING END LUBRICATION SHAFT CONNECTING END LUBRICATION DRILL FEATURE AN INDICATION OF WHETHER OR NOT A DRILL FEATURE FOR LUBRICATION PURPOSES IS INCLUDED WITH THE SHAFT CONNECTING END. SELECT REPLY CODE 10AA49 BQDBD 11METHOD,LUBRICATION,SHAFT CONNECTING END SHAFT CONNECTING END LUBRICATION METHOD THE MEANS USED TO LUBRICATE THE SHAFT CONNECTING END. SELECT REPLY CODE 10AB75 BQDCD /D/ 07COUNTERSINK,BORE BORE COUNTERSINK AN INDICATION OF WHETHER OR NOT A BORE COUNTERSINK IS INCLUDED. SELECT REPLY CODE 10AA49 BQDDD 08LOCATION,COUNTERSINK COUNTERSINK LOCATION INDICATES THE LOCATION OF THE COUNTERSINK ON THE ITEM. SELECT REPLY CODE 10AJ91 BQDFD /D/ 07BENCH BENCH AN INDICATION OF WHETHER OR NOT A BENCH IS PROVIDED. SELECT REPLY CODE 10AB22 BQDGD 18TYPE,BENCH BENCH TYPE INDICATES THE TYPE OF BENCH PROVIDED. SELECT REPLY CODE 10AA78 BQDHA 12QUANTITY,CHUCK CHUCK QUANTITY THE NUMBER OF CHUCKS PROVIDED. 1A MODE REPLY 0 BQDJJ T10RANGE,CHUCK CHUCK RANGE THE MINIMUM AND MAXIMUM LIMITS OF THE CHUCK. 1D AND 1F MODE REPLY11AA05 BQDKF T04ANGLE ADJUSTMENT RANGE IN DEG,FACE,VALVE VALVE FACE ANGLE ADJUSTMENT RANGE IN DEG THE ANGLE ADJUSTMENT RANGE OF THE VALVE FACE,EXPRESSED IN DEGREES. 1F MODE REPLY 0 BQDLJ 10SIZE ACCOMMODATED,HEAD,VALVE VALVE HEAD SIZE ACCOMMODATED DESIGNATES THE SIZE OF VALVE HEAD THE ITEM WILL ACCOMMODATE. 2D AND 1B MODE REPLY21AA051AC20 BQDMD 18TYPE,HOLE HOLE TYPE INDICATES THE TYPE OF HOLE(S) PROVIDED IN THE ITEM. SELECT REPLY CODE 10AH37 BQDND /D/ 07MEANS FOR GRINDING VALVE STEM AND ROCKER ARM,INTEGRAL INTEGRAL MEANS FOR GRINDING VALVE STEM AND ROCKER ARM AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES INTEGRAL MEANS FOR GRINDING THE VALVE STEM AND ROCKER ARM. SELECT REPLY CODE 10AA49 BQDPA 12QUANTITY,HOLE,DRILLED DRILLED HOLE QUANTITY THE NUMBER OF DRILLED HOLES IN THE ITEM. 1A MODE REPLY 0 BQDQD 08LOCATION,HOLE,DRILLED DRILLED HOLE LOCATION INDICATES THE LOCATION OF THE DRILLED HOLE(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 BQDRA 12QUANTITY,HOLE,TAPPED TAPPED HOLE QUANTITY THE NUMBER OF TAPPED HOLES IN THE ITEM. 1A MODE REPLY 0 BQDSD 08LOCATION,HOLE,TAPPED TAPPED HOLE LOCATION INDICATES THE LOCATION OF THE TAPPED HOLE(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 BQDTD 02DESIGN,SCREEN,LIGHT TRANSMISSION LIGHT TRANSMISSION SCREEN DESIGN THE SCREEN DESIGN WHICH CONTROLS THE EMERGENCE OF LIGHT QUANTITY TRANSMITTED. SELECT REPLY CODE 10AG41 BQDWJ 04WIDTH,MAXIMUM,BELT BELT MAXIMUM WIDTH THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BELT,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BQDXD /D/ 07RECESS,BEVEL BEVEL RECESS AN INDICATION OF WHETHER OR NOT A BEVEL RECESS IS PROVIDED. SELECT REPLY CODE 10AB22 BQDYD 14SHAPE FOR WHICH TOP IS DESIGNED,BASE,CENTRIFUGE TUBE CENTRIFUGE TUBE BASE SHAPE FOR WHICH TOP IS DESIGNED THE PHYSICAL CONFIGURATION OF THE CENTRIFUGE TUBE BASE FOR WHICH THE TOP IS DESIGNED. SELECT REPLY CODE 10AD07 BQDZJ 10CIRCUMFERENCE,BELT,MAXIMUM MAXIMUM BELT CIRCUMFERENCE THE MAXIMUM CIRCUMFERENCE OF THE BELT. 1D AND 1B MODE REPLY11AA05 BQFBD /D/ 07CLAMP,ROD,SUPPORT SUPPORT ROD CLAMP AN INDICATION OF WHETHER OR NOT A SUPPORT ROD CLAMP IS INCLUDED. SELECT REPLY CODE 10AA49 BQFCD /D/ 07RING,CONCENTRIC CONCENTRIC RING AN INDICATION OF WHETHER OR NOT A CONCENTRIC RING(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BQFDD /D/ 07CLAMP CLAMP AN INDICATION OF WHETHER OR NOT A CLAMP IS PROVIDED. SELECT REPLY CODE 10AB22 BQFFJ 04DISTANCE FROM RING TO SUPPORT ROD,CENTER TO CENTER CENTER TO CENTER DISTANCE FROM RING TO SUPPORT ROD THE DISTANCE FROM THE RING CENTER TO THE SUPPORT ROD CENTER. 2D AND 1B MODE REPLY21AA051AC20 BQFGD /D/ 07TABLE TABLE AN INDICATION OF WHETHER OR NOT A TABLE IS INCLUDED. SELECT REPLY CODE 10AA49 BQFHJ 04LENGTH,OVERALL,ARM ARM OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ARM. 2D AND 1B MODE REPLY21AA051AC20 BQFJD /D/ 07GROOVE,COLLAR,INTERNAL INTERNAL COLLAR GROOVE AN INDICATION OF WHETHER OR NOT AN INTERNAL COLLAR GROOVE IS INCLUDED. SELECT REPLY CODE 10AA49 BQFKA 12QUANTITY,RING,ADDITIONAL ADDITIONAL RING QUANTITY THE NUMBER OF ADDITIONAL RINGS PROVIDED. 1A MODE REPLY 0 BQFLD /D/ 07SHELF,BURNER BURNER SHELF AN INDICATION OF WHETHER OR NOT A BURNER SHELF IS INCLUDED. SELECT REPLY CODE 10AA49 BQFMD /D/ 07CLAMP,INDICATOR,DIAL DIAL INDICATOR CLAMP AN INDICATION OF WHETHER OR NOT A DIAL INDICATOR CLAMP IS INCLUDED. SELECT REPLY CODE 10AA49 BQFND /D/ 07FEATURE,WETPACK WETPACK FEATURE AN INDICATION OF WHETHER OR NOT A WETPACK FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BQFPJ 04DIAMETER ACCOMMODATED,BRAKE SHOE,MAXIMUM MAXIMUM BRAKE SHOE DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE BRAKE SHOE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BQFQJ 04DIAMETER ACCOMMODATED,BRAKE SHOE,MINIMUM MINIMUM BRAKE SHOE DIAMETER ACCOMMODATED THE MINIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE BRAKE SHOE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BQFRJ 04WIDTH ACCOMMODATED,MAXIMUM,BRAKE SHOE BRAKE SHOE MAXIMUM WIDTH ACCOMMODATED THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ACCOMMODATION FOR THE BRAKE SHOE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BQFSD /D/ 09MATERIAL,SPOON SPOON MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SPOON IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BQFTJ /D/ 10CAPACITY,CHAMBER,DESICCANT DESICCANT CHAMBER CAPACITY THE AMOUNT OF LIQUID,GRANULES,AND THE LIKE,THE DESICCANT CHAMBER WILL ACCOMMODATE. 1D AND 1B MODE REPLY12AG67 BQFWL 16STYLE DESIGNATOR,CONDENSER CONDENSER STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CONDENSER. 1L MODE REPLY 0 BQFXL 16STYLE DESIGNATOR,FLASK,BOILING BOILING FLASK STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BOILING FLASK. 1L MODE REPLY 0 BQFYD /D/ 07TIP,DRIP DRIP TIP AN INDICATION OF WHETHER OR NOT A DRIP TIP IS INCLUDED. SELECT REPLY CODE 10AA49 BQFZJ 10CAPACITY,FLASK,BOILING BOILING FLASK CAPACITY THE AMOUNT OF LIQUID,GRANULES,AND THE LIKE,THE BOILING FLASK WILL ACCOMMODATE. 1D AND 1B MODE REPLY12AG67 BQGBA /D/ 16STYLE DESIGNATOR,CHAMBER,DRYING DRYING CHAMBER STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE DRYING CHAMBER. 1A MODE REPLY 0 BQGCD 14SHAPE,SPINDLE SPINDLE SHAPE THE PHYSICAL CONFIGURATION OF THE SPINDLE. SELECT REPLY CODE 10AD07 BQGDD 14SHAPE,ABRASIVE ABRASIVE SHAPE THE PHYSICAL CONFIGURATION OF THE ABRASIVE. SELECT REPLY CODE 10AD07 BQGFJ 04DISTANCE FROM PIVOTING POINT,OUTREACH OUTREACH DISTANCE FROM PIVOTING POINT THE DISTANCE THE ITEM WILL REACH OUT FROM THE PIVOTING POINT. 2D AND 1B MODE REPLY21AA051AC20 BQGGJ 10LOAD RATING PER SET LOAD RATING PER SET THE RATED LOAD PER SET THE ITEM IS DESIGNED TO ACCOMMODATE. 2D AND 1B MODE REPLY22AG671AC20 BQGHJ 04DISTANCE BETWEEN DAVIT HEAD AND DECK DISTANCE BETWEEN DAVIT HEAD AND DECK THE DISTANCE BETWEEN THE DECK AND THE DAVIT HEAD. 2D AND 1B MODE REPLY21AA051AC20 BQGJJ 04LENGTH FOR WHICH DESIGNED,BOAT BOAT LENGTH FOR WHICH DESIGNED A MEASUREMENT OF THE LONGEST DIMENSION OF THE BOAT FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BQGKD /D/ 07FEATURE,STRONGBACK STRONGBACK FEATURE AN INDICATION OF WHETHER OR NOT A STRONGBACK FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BQGLD 08LOCATION,STRONGBACK STRONGBACK LOCATION INDICATES THE LOCATION OF THE STRONGBACK ON THE ITEM. SELECT REPLY CODE 10AJ91 BQGMJ 04DISTANCE BETWEEN FLOATING BLOCK RECESSES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FLOATING BLOCK RECESSES THE CENTER TO CENTER DISTANCE BETWEEN THE FLOATING BLOCK RECESSES. 2D AND 1B MODE REPLY21AA051AC20 BQGNG /D/ 19FACILITY,ATTACHING,HOISTING APPARATUS HOISTING APPARATUS ATTACHING FACILITY THE FACILITY/IES/ PROVIDED FOR ATTACHING THE HOISTING APPARATUS TO THE ITEM. FULL TEXT WRITE-IN 0 BQGPG /D/ 19FACILITY,ATTACHMENT,LIFTING LIFTING ATTACHMENT FACILITY THE FACILITY/IES/ PROVIDED FOR ATTACHING ITEMS TO BE LIFTED. FULL TEXT WRITE-IN 0 BQGQJ 04DISTANCE BELOW BEAM,DROP,HAND CHAIN HAND CHAIN DROP DISTANCE BELOW BEAM THE DISTANCE THE HAND CHAIN DROPS BELOW THE BEAM. 2D AND 1B MODE REPLY21AA051AC20 BQGRG /D/ 04SIZE FOR WHICH DESIGNED,I-BEAM I-BEAM SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE I-BEAM FOR WHICH THE ITEM IS DESIGNED. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/16/2024 FULL TEXT WRITE-IN 0 BQGSD /D/ 07WHEEL,FLANGED FLANGED WHEEL AN INDICATION OF WHETHER OR NOT A FLANGED WHEEL(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BQGTJ /D/A18TYPE/LOCATION AND QUANTITY,ATTACHMENT ATTACHMENT TYPE/LOCATION AND QUANTITY INDICATES THE TYPE,LOCATION,AND NUMBER OF ATTACHMENT(S). USE MRC BDHD WITH ISAC CODING TO TABLE 0370 AND RELATIONSHIP MRC TAQT TO MRC BDHD IN REPLACE OF THIS CANCELED MRC. 2D AND 1A MODE REPLY23AJ743AJ91 BQGWG /D/ 12LENGTH AND QUANTITY,LEG LEG LENGTH AND QUANTITY A MEASUREMENT OF THE LONGEST DIMENSION OF A LEG,IN DISTINCTION FROM WIDTH,AND THE NUMBER OF EACH. FULL TEXT WRITE-IN 0 BQGXA 12QUANTITY,LOOP LOOP QUANTITY THE NUMBER OF LOOPS PROVIDED. 1A MODE REPLY 0 BQGYJ 10CIRCUMFERENCE,INSIDE,LOOP LOOP INSIDE CIRCUMFERENCE THE DISTANCE AROUND THE INSIDE SURFACE OF THE LOOP. 2D AND 1B MODE REPLY21AA051AC20 BQGZD 19FORM,ASSEMBLY,DRUM HOOK DRUM HOOK ASSEMBLY FORM THE ASSEMBLY FORM OF THE DRUM HOOK. SELECT REPLY CODE 10AE33 BQHBD /D/ 07FACING,GUM,CUSHION CUSHION GUM FACING AN INDICATION OF WHETHER OR NOT A CUSHION GUM FACING IS INCLUDED. SELECT REPLY CODE 10AA49 BQHCJ /D/ 10AREA AREA THE MEASURED SURFACE OF THE ITEM. 2D AND 1B MODE REPLY22AG671AC20 BQHDD /D/ 07UNIT,HEAT,ATTACHED ATTACHED HEAT UNIT AN INDICATION OF WHETHER OR NOT AN ATTACHED HEAT UNIT IS INCLUDED. SELECT REPLY CODE 10AA49 BQHFD /D/ 18TYPE FOR WHICH DESIGNED,REPAIR REPAIR TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF REPAIR FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BQHGA 03DESIGNATOR,SIZE,TOP TERMINAL TOP TERMINAL SIZE DESIGNATOR A DESIGNATION INDICATING THE SIZE BY WHICH THE TOP TERMINAL IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1A MODE REPLY 0 BQHHD /D/ 07SPREADER,SLING SLING SPREADER AN INDICATION OF WHETHER OR NOT A SLING SPREADER IS INCLUDED. PLEASE USE MRC ABFF OR TMQY INPLACE OF THIS CANCELD MRC. SELECT REPLY CODE 10AA49 BQHJD /D/ 07BAR,SPREADER SPREADER BAR AN INDICATION OF WHETHER OR NOT A SPREADER BAR IS INCLUDED. SELECT REPLY CODE 10AA49 BQHKJ 10CAPACITY,LIFTING LIFTING CAPACITY THE LIFTING CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BQHLJ 04LENGTH,OVERALL,BEAM BEAM OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BEAM. 2D AND 1B MODE REPLY21AA051AC20 BQHMJ 04WIDTH,OVERALL,BEAM BEAM OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BEAM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BQHNJ 04DIAMETER,OVERALL,BEAM BEAM OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF A BEAM. 2D AND 1B MODE REPLY21AA051AC20 BQHPD /D/ 07BAR,HOLDING,SHEET SHEET HOLDING BAR AN INDICATION OF WHETHER OR NOT A SHEET HOLDING BAR IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BQHQJ A18TYPE AND QUANTITY,ATTACHMENT,BEAM TO HOISTING APPARATUS BEAM TO HOISTING APPARATUS ATTACHMENT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF FACILITIES PROVIDED FOR ATTACHING THE BEAM TO THE HOISTING APPARATUS. 1D AND 1A MODE REPLY13AJ74 BQHRJ A18TYPE AND QUANTITY,ATTACHMENT,BEAM TO LOAD BEAM TO LOAD ATTACHMENT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF FACILITIES PROVIDED FOR ATTACHING THE LOAD TO THE BEAM. 1D AND 1A MODE REPLY12AB47 BQHSD /D/ 07ROPE,GUIDE,COMMON ATTACHMENT COMMON ATTACHMENT GUIDE ROPE AN INDICATION OF WHETHER OR NOT A COMMON ATTACHMENT GUIDE ROPE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BQHTA 12QUANTITY,ROPE,GUIDE GUIDE ROPE QUANTITY THE NUMBER OF GUIDE ROPES PROVIDED. 1A MODE REPLY 0 BQHWD /D/ 09MATERIAL,ROPE,GUIDE GUIDE ROPE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE GUIDE ROPE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BQHXJ 04LENGTH,ROPE,GUIDE GUIDE ROPE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A GUIDE ROPE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BQHYJ 04DIAMETER,MAXIMUM,REPAIRABLE PUNCTURE REPAIRABLE PUNCTURE MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE REPAIRABLE PUNCTURE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BQHZJ 10CONTENT,COMPOUND,RUBBER RUBBER COMPOUND CONTENT THE AMOUNT OF RUBBER COMPOUND THE ITEM CONTAINS. 1D AND 1B MODE REPLY12AG67 BQJBD 18TYPE,PLUNGER PLUNGER TYPE INDICATES THE TYPE OF PLUNGER PROVIDED. SELECT REPLY CODE 10AK54 BQJCJ 04THICKNESS,FACING FACING THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE FACING,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BQJDG 19ITEM FOR WHICH BOTTOM TERMINAL IS DESIGNED ITEM FOR WHICH BOTTOM TERMINAL IS DESIGNED THE ITEM FOR WHICH THE BOTTOM TERMINAL/S/ IS DESIGNED. FULL TEXT WRITE-IN 0 BQJFJ /D/ 04RADIUS,BOTTOM,LEFT SIDE FLANGE LEFT SIDE FLANGE BOTTOM RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQJGJ 04WIDTH,FLANGE,TOP TOP FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BQJHJ 04WIDTH,FLANGE,BOTTOM BOTTOM FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BQJKJ 04THICKNESS,TIP,LEFT SIDE TOP FLANGE LEFT SIDE TOP FLANGE TIP THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQJLJ 04THICKNESS,TIP,LEFT SIDE BOTTOM FLANGE LEFT SIDE BOTTOM FLANGE TIP THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQJMJ 04THICKNESS,TIP,RIGHT SIDE TOP FLANGE RIGHT SIDE TOP FLANGE TIP THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQJNJ 04THICKNESS,TIP,RIGHT SIDE BOTTOM FLANGE RIGHT SIDE BOTTOM FLANGE TIP THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQJPB /D/ 04ANGLE IN DEG,INNER FACE TO OUTER FACE,LEFT TOP LEFT TOP INNER FACE TO OUTER FACE ANGLE IN DEG NONE. 1B MODE REPLY 0 BQJQB /D/ 04ANGLE IN DEG,INNER FACE TO OUTER FACE,LEFT BOTTOM LEFT BOTTOM INNER FACE TO OUTER FACE ANGLE IN DEG NONE. 1B MODE REPLY 0 BQJRB /D/ 04ANGLE IN DEG,INNER FACE TO OUTER FACE,RIGHT TOP RIGHT TOP INNER FACE TO OUTER FACE ANGLE IN DEG NONE. 1B MODE REPLY 0 BQJSB /D/ 04ANGLE IN DEG,INNER FACE TO OUTER FACE,RIGHT BOTTOM RIGHT BOTTOM INNER FACE TO OUTER FACE ANGLE IN DEG NONE. 1B MODE REPLY 0 BQJTJ /D/ 04RADIUS WHERE END FLANGE JOINS BOTTOM FLANGE,CORNER,LEFT SIDE INNER LEFT SIDE INNER CORNER RADIUS WHERE END FLANGE JOINS BOTTOM FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BQJWJ /D/ 04RADIUS WHERE END FLANGE JOINS BOTTOM FLANGE,CORNER,LEFT SIDE OUTER LEFT SIDE OUTER CORNER RADIUS WHERE END FLANGE JOINS BOTTOM FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BQJXJ /D/ 04RADIUS WHERE END FLANGE JOINS BOTTOM FLANGE,CORNER,RIGHT SIDE INNER RIGHT SIDE INNER CORNER RADIUS WHERE END FLANGE JOINS BOTTOM FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BQJYJ /D/ 04RADIUS WHERE END FLANGE JOINS BOTTOM FLANGE,CORNER,RIGHT SIDE OUTER RIGHT SIDE OUTER CORNER RADIUS WHERE END FLANGE JOINS BOTTOM FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BQJZJ /D/ 04HEIGHT,BOTTOM,LEFT SIDE FLANGE LEFT SIDE FLANGE BOTTOM HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BQKBJ /D/ 04HEIGHT,BOTTOM,RIGHT SIDE FLANGE RIGHT SIDE FLANGE BOTTOM HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BQKCJ /D/ 04RADIUS OF FILLET AT LEFT SIDE OF BULB,LEG LEG RADIUS OF FILLET AT LEFT SIDE OF BULB NONE. 2D AND 1B MODE REPLY21AA051AC20 BQKDJ /D/ 04RADIUS OF FILLET AT RIGHT SIDE OF BULB,LEG LEG RADIUS OF FILLET AT RIGHT SIDE OF BULB NONE. 2D AND 1B MODE REPLY21AA051AC20 BQKFJ /D/ 04RADIUS AT RIGHT SIDE OF TOE,LEG LEG RADIUS AT RIGHT SIDE OF TOE NONE. 2D AND 1B MODE REPLY21AA051AC20 BQKGJ /D/ 04RADIUS AT LEFT SIDE OF TOE,LEG LEG RADIUS AT LEFT SIDE OF TOE NONE. 2D AND 1B MODE REPLY21AA051AC20 BQKHJ 04THICKNESS,TIP,LEG LEG TIP THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQKJH /D/ 19FINISH AND LOCATION,SURFACE,POINTER POINTER SURFACE FINISH AND LOCATION AN INDICATION OF THE SURFACE FINISH ON THE POINTER AND THE LOCATION. 2D MODE REPLY 21AB543AJ91 BQKKH /D/ 01COLOR AND LOCATION,POINTER POINTER COLOR AND LOCATION AN INDICATION OF THE COLOR ON THE POINTER AND THE LOCATION. 2D MODE REPLY 26AD063AJ91 BQKLJ 04RADIUS,CORNER,LEFT END,OUTER FACE TOP FLANGE OUTER FACE TOP FLANGE LEFT END CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQKMJ /D/ 04RADIUS,CORNER,LEFT,OUTER FACE BOTTOM FLANGE OUTER FACE BOTTOM FLANGE LEFT CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQKNJ /D/ 04DISTANCE,OUTER FACE TO FLANGE TO CENTERLINE OF TOP FLANGE OUTER FACE TO FLANGE TO CENTERLINE OF TOP FLANGE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 BQKPJ /D/ 04RADIUS,CORNER,RIGHT,OUTER FACE TOP FLANGE OUTER FACE TOP FLANGE RIGHT CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQKQJ 04RADIUS WHERE TOP LEFT FLANGE JOINS WEB FLANGE,OUTER OUTER RADIUS WHERE TOP LEFT FLANGE JOINS WEB FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BQKRJ 04RADIUS WHERE BOTTOM RIGHT FLANGE JOINS WEB FLANGE,OUTER OUTER RADIUS WHERE BOTTOM RIGHT FLANGE JOINS WEB FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BQKSJ /D/ 04DIAMETER AT TOE,LEG LEG DIAMETER AT TOE NONE. 2D AND 1B MODE REPLY21AA051AC20 BQKTJ /D/ 04DEPTH,PILING PILING DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BQKWJ /D/ 04WIDTH,PILING PILING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BQKXJ /D/ 04WIDTH,LEG/FLANGE,LEFT LEFT LEG/FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BQKYJ /D/ 04WIDTH,LEG/FLANGE,RIGHT RIGHT LEG/FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BQKZJ /D/ 04DISTANCE FROM CENTER OF TOP LEG SOCKET/BALL TO END OF LEFT LEG DISTANCE FROM CENTER OF TOP LEG SOCKET/BALL TO END OF LEFT LEG NONE. 2D AND 1B MODE REPLY21AA051AC20 BQLBJ /D/ 04DISTANCE FROM CENTER OF TOP LEG SOCKET/BALL TO END OF RIGHT LEG DISTANCE FROM CENTER OF TOP LEG SOCKET/BALL TO END OF RIGHT LEG NONE. 2D AND 1B MODE REPLY21AA051AC20 BQLCJ /D/ 04DISTANCE FROM CENTER OF LEFT LEG SOCKET/BALL TO END OF TOP LEG DISTANCE FROM CENTER OF LEFT LEG SOCKET/BALL TO END OF TOP LEG NONE. 2D AND 1B MODE REPLY21AA051AC20 BQLDA /D/ 16STYLE DESIGNATOR,CHAMBER,DESICCANT DESICCANT CHAMBER STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE DESICCANT CHAMBER. 1A MODE REPLY 0 BQLFJ 04SIZE ACCOMMODATED,AXLE,MAXIMUM MAXIMUM AXLE SIZE ACCOMMODATED THE MAXIMUM AXLE SIZE THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BQLGG /D/ 04SIZE,JOINT,DRYING CHAMBER TO DESICCANT CHAMBER DRYING CHAMBER TO DESICCANT CHAMBER JOINT SIZE NONE. FULL TEXT WRITE-IN 0 BQLHG /D/ 04SIZE,JOINT,DRYING CHAMBER TO BOILING FLASH DRYING CHAMBER TO BOILING FLASH JOINT SIZE NONE. FULL TEXT WRITE-IN 0 BQLJG /D/ 04SIZE,JOINT,DRYING CHAMBER TO CONDENSER DRYING CHAMBER TO CONDENSER JOINT SIZE NONE. FULL TEXT WRITE-IN 0 BQLKG 04SIZE,JOINT,VAPOR INLET VAPOR INLET JOINT SIZE NONE. FULL TEXT WRITE-IN 0 BQLLG 04SIZE,JOINT,CONDENSOR OUTLET CONDENSOR OUTLET JOINT SIZE NONE. FULL TEXT WRITE-IN 0 BQLMJ 04LENGTH,JACKET JACKET LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BQLND 19POSITION,FEED FEED POSITION AN INDICATION OF THE POSITION OF THE FEED. SELECT REPLY CODE 10AK54 BQLPD 18TYPE,DRIVE,WHEEL SPINDLE WHEEL SPINDLE DRIVE TYPE INDICATES THE TYPE OF DRIVE FOR TURNING,ROTATING,OR POSITIONING THE WHEEL SPINDLE MECHANISM. SELECT REPLY CODE 10AG25 BQLQJ 10CAPACITY,LOAD LOAD CAPACITY THE RATED LOAD THAT THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY12AG67 BQLRD 18TYPE,SPINDLE SPINDLE TYPE INDICATES THE TYPE OF SPINDLE PROVIDED. SELECT REPLY CODE 10AC55 BQLSB /D/ 10HEAT RATING IN BTU,GAS,MAXIMUM MAXIMUM GAS HEAT RATING IN BTU THE MAXIMUM GAS HEAT RATING,EXPRESSED IN BRITISH THERMAL UNITS. 1B MODE REPLY 0 BQLTJ 04DIAMETER,ARBOR ARBOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ARBOR,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BQLWD /D/ 09MATERIAL,ELEMENT,ROLLING ROLLING ELEMENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ROLLING ELEMENT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BQLXA 12QUANTITY,UNIT,DISTILLING DISTILLING UNIT QUANTITY THE NUMBER OF DISTILLING UNITS INCLUDED. 1A MODE REPLY 0 BQLYJ 04DISTANCE FROM SPINDLE CENTER TO MOUNTING DISTANCE FROM SPINDLE CENTER TO MOUNTING THE DISTANCE FROM THE CENTER OF THE SPINDLE TO THE MOUNTING. 2D AND 1B MODE REPLY21AA051AC20 BQLZJ 04HEIGHT,OVERALL,CONDENSER JACKET CONDENSER JACKET OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE CONDENSER JACKET. 2D AND 1B MODE REPLY21AA051AC20 BQMBJ /D/ 04LENGTH,OVERALL,CONDENSER JACKET CONDENSER JACKET OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CONDENSER JACKET. 2D AND 1B MODE REPLY21AA051AC20 BQMCJ 04DISTANCE BETWEEN INSIDE WHEEL FLANGES ON SPINDLE DISTANCE BETWEEN INSIDE WHEEL FLANGES ON SPINDLE THE DISTANCE BETWEEN THE INSIDE WHEEL FLANGES ON THE SPINDLE. 2D AND 1B MODE REPLY21AA051AC20 BQMDJ 04DIAMETER,OVERALL,BOILER CHAMBER BOILER CHAMBER OVERALL DIAMETER THE OVERALL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOILER CHAMBER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BQMFJ 04HEIGHT,OVERALL,BOILER CHAMBER BOILER CHAMBER OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE BOILER CHAMBER. 2D AND 1B MODE REPLY21AA051AC20 BQMGD /D/ 07SUPPRESSION,INTERFERENCE,MOTOR RADIO MOTOR RADIO INTERFERENCE SUPPRESSION AN INDICATION OF WHETHER OR NOT A MOTOR RADIO INTERFERENCE SUPPRESSION IS INCLUDED. SELECT REPLY CODE 10AA49 BQMHD /D/ 09MATERIAL,WALL,OUTER,CABINET CABINET OUTER WALL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CABINET OUTER WALL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BQMJD /D/ 09MATERIAL,WALL,INNER,CABINET CABINET INNER WALL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CABINET INNER WALL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BQMKD /D/ 07CABLE/PLUG,EXTENSION,ELECTRIC ELECTRIC EXTENSION CABLE/PLUG AN INDICATION OF WHETHER OR NOT AN ELECTRIC EXTENSION CABLE AND PLUG IS INCLUDED. SELECT REPLY CODE 10AA49 BQMLD 18TYPE,MOUNTING,CABINET CABINET MOUNTING TYPE INDICATES THE TYPE OF MOUNT UTILIZED TO SUPPORT THE CABINET. SELECT REPLY CODE 10AM39 BQMMJ 04LENGTH,CORD CORD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CORD,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BQMNA 12QUANTITY,DOOR,OUTER OUTER DOOR QUANTITY THE NUMBER OF OUTER DOORS INCLUDED. 1A MODE REPLY 0 BQMPD /D/ 09MATERIAL,DOOR,OUTER OUTER DOOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE OUTER DOOR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BQMQA 12QUANTITY,HANDBOOK,INSTRUCTION INSTRUCTION HANDBOOK QUANTITY THE NUMBER OF INSTRUCTION HANDBOOKS PROVIDED. 1A MODE REPLY 0 BQMRD /D/ 07FEATURE,INSULATION,OUTER DOOR OUTER DOOR INSULATION FEATURE AN INDICATION OF WHETHER OR NOT AN OUTER DOOR INSULATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BQMSA 12QUANTITY,DOOR,INNER INNER DOOR QUANTITY THE NUMBER OF INNER DOORS INCLUDED. 1A MODE REPLY 0 BQMTD /D/ 09MATERIAL,DOOR,INNER INNER DOOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INNER DOOR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BQMWD 11METHOD,MOUNTING,INNER DOOR INNER DOOR MOUNTING METHOD THE MEANS OF ATTACHING THE INNER DOOR. SELECT REPLY CODE 10AM39 BQMXJ 04SIZE ACCOMMODATED,PIPE,MINIMUM MINIMUM PIPE SIZE ACCOMMODATED DESIGNATES THE MINIMUM PIPE SIZE THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BQMYJ 04SIZE ACCOMMODATED,PIPE,MAXIMUM MAXIMUM PIPE SIZE ACCOMMODATED DESIGNATES THE MAXIMUM PIPE SIZE THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BQMZJ 04DIAMETER ACCOMMODATED,BOLT,MINIMUM MINIMUM BOLT DIAMETER ACCOMMODATED THE MINIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE BOLT,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BQNBJ 04DIAMETER ACCOMMODATED,BOLT,MAXIMUM MAXIMUM BOLT DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE BOLT,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BQNCA 12QUANTITY,HEAD,DIE DIE HEAD QUANTITY THE NUMBER OF DIE HEADS PROVIDED. 1A MODE REPLY 0 BQNDD /D/ 18TYPE,HEAD,DIE DIE HEAD TYPE INDICATES THE TYPE OF DIE HEAD PROVIDED. SELECT REPLY CODE 10AE98 BQNFD 19MARKING,INDEX,TAB TAB INDEX MARKING AN INDICATION OF THE TAB INDEX MARKING. SELECT REPLY CODE 10AJ65 BQNGJ 04WIDTH,OVERALL,DIVIDER DIVIDER OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE DIVIDER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BQNHJ 04HEIGHT,OVERALL,DIVIDER DIVIDER OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE DIVIDER. 2D AND 1B MODE REPLY21AA051AC20 BQNJG 18TYPE,DESIGN,FASTENER FASTENER DESIGN TYPE INDICATES THE TYPE OF THE FASTENER DESIGN. FULL TEXT WRITE-IN 0 BQNKG 08LOCATION,FASTENER FASTENER LOCATION INDICATES THE LOCATION OF THE FASTENER IN RELATION TO THE ITEM. FULL TEXT WRITE-IN 0 BQNLD 01COLOR,COVER COVER COLOR THE HUE OR TINT OF THE COVER. SELECT REPLY CODE 10AD06 BQNMD 18TYPE,DESIGN,COVER COVER DESIGN TYPE INDICATES THE TYPE OF THE COVER DESIGN. SELECT REPLY CODE 10AD03 BQNND 18TYPE,BACK,COVER COVER BACK TYPE INDICATES THE TYPE OF COVER BACK PROVIDED. SELECT REPLY CODE 10AF72 BQNPD /D/ 07HINGE,CENTER CENTER HINGE AN INDICATION OF WHETHER OR NOT A CENTER HINGE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BQNQD /D/ 08LOCATION,OPENING,COVER COVER OPENING LOCATION INDICATES THE LOCATION OF THE COVER OPENING/S/ ON THE ITEM. PLEASE USE MRC ARQT IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AJ91 BQNRF T10ACCURACY IN DECIBELS,ATTENUATION,OVERALL OVERALL ATTENUATION ACCURACY IN DECIBELS THE OVERALL LIMITS OF PERMISSIBLE VARIATION IN THE ATTENUATION ACCURACY FROM THE NOMINAL VALUE AT A SPECIFIED FREQUENCY RATING OR RANGE,EXPRESSED IN DECIBELS. 1F MODE REPLY 0 BQNSF T10RANGE IN DECIBELS,ATTENUATION,SEGMENT SEGMENT ATTENUATION RANGE IN DECIBELS THE MINIMUM AND MAXIMUM LIMITS OF ATTENUATION WITHIN THE OVERALL ATTENUATION RANGE FOR WHICH A RELATED ACCURACY VALUE HAS BEEN SPECIFIED,EXPRESSED IN DECIBELS. 1F MODE REPLY 0 BQNTF T10ACCURACY IN DECIBELS,ATTENUATION,SEGMENT SEGMENT ATTENUATION ACCURACY IN DECIBELS THE LIMITS OF PERMISSIBLE VARIATION IN THE ATTENUATION ACCURACY AT ANY POINT BETWEEN TWO SPECIFIED ATTENUATION VALUES WITHIN THE OVERALL RANGE OF THE ITEM,EXPRESSED IN DECIBELS. 1F MODE REPLY 0 BQNWJ 10ACCURACY,FLATNESS,LAP LAP FLATNESS ACCURACY A MEASUREMENT OF THE AMOUNT OF VARIANCE OF THE LAP. 2D AND 1B MODE REPLY21AA051AC20 BQNXD 02DESIGN,GROOVE,LAP LAP GROOVE DESIGN THE DESIGN OF THE LAP GROOVE/S/. SELECT REPLY CODE 10AD07 BQNYD 19PATTERN,GROOVING,LAP LAP GROOVING PATTERN THE OVERALL PATTERN OF THE LAP GROOVE(S). SELECT REPLY CODE 10AD07 BQNZD 19FACILITY,HOLDING,WORK WORK HOLDING FACILITY THE WORK HOLDING FACILITY INCLUDED ON THE ITEM. SELECT REPLY CODE 10AG25 BQPBA 12QUANTITY,FACILITY,WORK HOLDING WORK HOLDING FACILITY QUANTITY THE NUMBER OF WORK HOLDING FACILITIES INCLUDED WITH THE ITEM. 1A MODE REPLY 0 BQPCJ 04LENGTH,FACILITY,WORK HOLDING WORK HOLDING FACILITY LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE WORK HOLDING FACILITY,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BQPDD /D/ 07HINGE,METAL METAL HINGE AN INDICATION OF WHETHER OR NOT A METAL HINGE IS PROVIDED. IF PROVIDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AB22 BQPFA 12QUANTITY,FASTENER FASTENER QUANTITY THE NUMBER OF FASTENERS PROVIDED WITH THE ITEM. 1A MODE REPLY 0 BQPGG 04SPACING,CENTER,FASTENER FASTENER CENTER SPACING AN INDICATION OF THE SPACING BETWEEN THE FASTENER CENTERS. FULL TEXT WRITE-IN 0 BQPHJ 04HEIGHT,OVERALL,BEAM BEAM OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE BEAM. 2D AND 1B MODE REPLY21AA051AC20 BQPJJ /D/ 04WIDTH,THONG THONG WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE THONG,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BQPKJ 04LENGTH,SHEET,ACCOMMODATED ACCOMMODATED SHEET LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SHEET THAT THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BQPLJ 04WIDTH,SHEET,ACCOMMODATED ACCOMMODATED SHEET WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SHEET THAT THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BQPMJ T10RANGE,VALUE,OVERALL ELECTRICAL OVERALL ELECTRICAL VALUE RANGE AN INDICATION OF THE MINIMUM AND MAXIMUM OVERALL ELECTRICAL VALUE OF THE ITEM. 1D AND 1F MODE REPLY12AB49 BQPNJ 10VALUE PER SECTION,INCREMENT,ELECTRICAL ELECTRICAL INCREMENT VALUE PER SECTION THE INCREMENT OF ELECTRICAL VALUE PROVIDED BY EACH SECTION. 1D AND 1B MODE REPLY12AB49 BQPPA 12QUANTITY,SIDE,OPENING OPENING SIDE QUANTITY THE NUMBER OF SIDES WHICH OPEN. 1A MODE REPLY 0 BQPQD /D/ 07STRING,TIE TIE STRING AN INDICATION OF WHETHER OR NOT A TIE STRING IS INCLUDED. SELECT REPLY CODE 10AA49 BQPRD /D/ 07FASTENER,SLIDE SLIDE FASTENER AN INDICATION OF WHETHER OR NOT A SLIDE FASTENER IS INCLUDED. SELECT REPLY CODE 10AA49 BQPSG /D/ 18TYPE AND LOCATION,POCKET POCKET TYPE AND LOCATION INDICATES THE TYPE AND LOCATION OF THE POCKET. FULL TEXT WRITE-IN 0 BQPTD /D/ 07BINDER,RING RING BINDER AN INDICATION OF WHETHER OR NOT A RING BINDER IS INCLUDED. SELECT REPLY CODE 10AA49 BQPWD /D/ 07REMOVABILITY,BINDER,RING RING BINDER REMOVABILITY AN INDICATION OF WHETHER OR NOT THE RING BINDER IS REMOVABLE. SELECT REPLY CODE 10AC29 BQPXJ /D/ 04DIAMETER,RING RING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A RING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BQPYJ /D/ 04SPACING,RING RING SPACING THE SPACING BETWEEN RINGS. 2D AND 1B MODE REPLY21AA051AC20 BQPZD /D/ 07INSERT,PAPER PAPER INSERT AN INDICATION OF WHETHER OR NOT A PAPER INSERT IS INCLUDED. SELECT REPLY CODE 10AA49 BQQBG /D/ 08LOCATION AND QUANTITY,HOLE HOLE LOCATION AND QUANTITY INDICATES THE LOCATION AND THE TOTAL NUMBER OF HOLES. FULL TEXT WRITE-IN 0 BQQCF T10COEFFICIENT OF ELECTRICAL VALUE IN PPM PER DEG CELSIUS,TEMP TEMP COEFFICIENT OF ELECTRICAL VALUE IN PPM PER DEG CELSIUS THE CONSTANT THAT REPRESENTS THE PROPORTIONATE CHANGE IN VALUE CAUSED BY A CHANGE IN TEMPERATURE,EXPRESSED IN PARTS PER MILLION PER DEGREE CELSIUS. 1F MODE REPLY 0 BQQDJ /D/ 08LOCATION,LEGEND LEGEND LOCATION INDICATES THE LOCATION OF THE LEGEND ON THE ITEM. 2D AND 1B MODE REPLY21AA053AJ91 BQQFD /D/ 07HOLDER,UMBRELLA UMBRELLA HOLDER AN INDICATION OF WHETHER OR NOT AN UMBRELLA HOLDER IS INCLUDED. SELECT REPLY CODE 10AA49 BQQGD /D/ 09MATERIAL,HOOK HOOK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HOOK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH USE OF ISAC IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 BQQHA 12QUANTITY,HOOK,COAT/HAT COAT/HAT HOOK QUANTITY THE NUMBER OF COAT AND/OR HAT HOOKS PROVIDED. 1A MODE REPLY 0 BQQJD 19FLEXIBILITY,JOINT,BASE BASE JOINT FLEXIBILITY AN INDICATION OF THE BASE JOINT FLEXIBILITY. SELECT REPLY CODE 10AD03 BQQKD 18TYPE,RECEPTACLE,ASH ASH RECEPTACLE TYPE INDICATES THE TYPE OF ASH RECEPTACLE PROVIDED. SELECT REPLY CODE 10AM17 BQQLD 08LOCATION,RECEPTACLE,ASH ASH RECEPTACLE LOCATION INDICATES THE LOCATION OF THE ASH RECEPTACLE ON THE ITEM. SELECT REPLY CODE 10AJ91 BQQMD /D/ 07TRAY,SERVING SERVING TRAY AN INDICATION OF WHETHER OR NOT A SERVING TRAY IS INCLUDED. SELECT REPLY CODE 10AA49 BQQND /D/ 07FEATURE,BASE,WEIGHTED WEIGHTED BASE FEATURE AN INDICATION OF WHETHER OR NOT A WEIGHTED BASE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BQQPD /D/ 07FEATURE,BASE,ROCKING ROCKING BASE FEATURE AN INDICATION OF WHETHER OR NOT A ROCKING BASE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BQQQD /D/ 07WINGS,SIDE SIDE WINGS AN INDICATION OF WHETHER OR NOT SIDE WINGS ARE INCLUDED. SELECT REPLY CODE 10AA49 BQQRJ 04THICKNESS,GLASS GLASS THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE GLASS,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BQQTD /D/ 07ETCHING,ORNAMENTAL ORNAMENTAL ETCHING AN INDICATION OF WHETHER OR NOT ORNAMENTAL ETCHING IS INCLUDED. SELECT REPLY CODE 10AA49 BQQWJ 04LENGTH ACCOMMODATED,PICTURE PICTURE LENGTH ACCOMMODATED A MEASUREMENT OF THE LONGEST DIMENSION OF THE PICTURE THAT THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BQQXJ 04WIDTH ACCOMMODATED,PICTURE PICTURE WIDTH ACCOMMODATED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PICTURE THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BQQYD /D/ 09MATERIAL,COVERING,PANEL PANEL COVERING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PANEL COVERING IS FABRICATED. SELECT REPLY CODE 10AD09 BQQZD 01COLOR,PANEL PANEL COLOR THE HUE OR TINT OF THE PANEL. SELECT REPLY CODE 10AD06 BQRAJ /D/ 04WIDTH,SECTION,INDIVIDUAL INDIVIDUAL SECTION WIDTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 2D AND 1B MODE REPLY21AA051AC20 BQRBJ 04HEIGHT,SECTION,INDIVIDUAL INDIVIDUAL SECTION HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN INDIVIDUAL SECTION,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BQRCJ 04LENGTH,SECTION,INDIVIDUAL INDIVIDUAL SECTION LENGTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN INDIVIDUAL SECTION,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BQRDD /D/ 07TIEBACK TIEBACK AN INDICATION OF WHETHER OR NOT A TIEBACK(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BQRFD /D/ 07HOOK,SEWN-IN SEWN-IN HOOK AN INDICATION OF WHETHER OR NOT A SEWN-IN HOOK(S) IS FURNISHED. SELECT REPLY CODE 10AA55 BQRGJ /D/ 10CONTENT IN PERCENT,MATERIAL MATERIAL CONTENT IN PERCENT THE AMOUNT OF MATERIAL CONTAINED IN THE ITEM,EXPRESSED IN PERCENT. 1D AND 1B MODE REPLY16AD09 BQRHJ 10WEIGHT,FINISHED FINISHED WEIGHT A RELATIVE MEASURE OF THE MASS OF AN ITEM WITH RESPECT TO ITS DENSITY WHEN FINISHED. 2D AND 1B MODE REPLY22AG671AC20 BQRJD /D/ 19SOURCE,PATTERN/STYLE PATTERN/STYLE SOURCE THE NAME OF THE GOVERNMENT AGENCY,COMMERCIAL ORGANIZATION,OR MANUFACTURER CONTROLLING THE PATTERN AND/OR STYLE DESIGNATOR. SELECT REPLY CODE 10AF94 BQRKD /D/ 19SOURCE,SHADE,MARKING MARKING SHADE SOURCE THE NAME OF THE REFERENCE SOURCE OF THE MARKING SHADE IDENTIFICATION DESIGNATOR. SELECT REPLY CODE 10AF94 BQRLJ 04LENGTH,TORN TORN LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TORN ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BQRMJ 04LENGTH,FINISHED FINISHED LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FINISHED ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BQRNA /D/ 19IDENTIFICATION,SHADE,MARKING MARKING SHADE IDENTIFICATION A DESIGNATION APPLIED TO A PARTICULAR GRADATION OF A COLOR FOR THE PURPOSE OF READY IDENTIFICATION OF THE MARKING. 1A MODE REPLY 0 BQRPD 07DISPOSABILITY DISPOSABILITY AN INDICATION OF WHETHER OR NOT AN ITEM IS DISPOSABLE. SELECT REPLY CODE 10AJ61 BQRQD 02DESIGN,MOUNTING MOUNTING DESIGN THE DESIGN OF THE MOUNTING. SELECT REPLY CODE 10AH79 BQRRD 18TYPE,SLAT SLAT TYPE INDICATES THE TYPE OF SLAT PROVIDED. SELECT REPLY CODE 10AB00 BQRSJ 04WIDTH,PROJECTION PROJECTION WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BQRTJ 04HEIGHT,DROP DROP HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE DROP,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BQRWD 18TYPE,TRIM,BOTTOM EDGE BOTTOM EDGE TRIM TYPE INDICATES THE TYPE OF BOTTOM EDGE TRIM PROVIDED. SELECT REPLY CODE 10AK84 BQRXD 07REMOVABILITY,COVER COVER REMOVABILITY AN INDICATION OF WHETHER OR NOT THE COVER IS REMOVABLE. SELECT REPLY CODE 10AC29 BQRYD /D/ 07STRAP STRAP AN INDICATION OF WHETHER OR NOT A STRAP(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BQRZD /D/ 09MATERIAL,SHADE SHADE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHADE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BQSBD /D/ 07FEATURE,RESISTANT,STAIN STAIN RESISTANT FEATURE AN INDICATION OF WHETHER OR NOT A STAIN RESISTANT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BQSCJ 04WIDTH,OVERALL,ROLLER ROLLER OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ROLLER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BQSDD 18TYPE,HEM HEM TYPE INDICATES THE TYPE OF HEM PROVIDED. SELECT REPLY CODE 10AK84 BQSFD /D/ 07COUNTERBORE,BORE BORE COUNTERBORE AN INDICATION OF WHETHER OR NOT A BORE COUNTERBORE IS INCLUDED. SELECT REPLY CODE 10AA49 BQSGD /D/ 07DEVICE,ADJUSTING ADJUSTING DEVICE AN INDICATION OF WHETHER OR NOT AN ADJUSTING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 BQSHJ /D/ 04DIAMETER,AA END AA END DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BQSJJ /D/ 04DIAMETER,SHANK,BB END BB END SHANK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BQSKJ /D/ 04LENGTH,CHAMFER,BB END BB END CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 BQSLB 04ANGLE IN DEG,CHAMFER,BB END BB END CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 BQSMJ /D/ 04LENGTH,CHAMFER,AA END AA END CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 BQSNB 04ANGLE IN DEG,CHAMFER,AA END AA END CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 BQSPJ /D/ 04RADIUS,AA END AA END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQSQJ /D/ 04RADIUS,BB END BB END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQSRJ 04RADIUS,FILLET,FIRST,SHOULDER SHOULDER FIRST FILLET RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQSTJ 04RADIUS,FILLET,SECOND,SHOULDER SHOULDER SECOND FILLET RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQSXJ 04RADIUS,STEP,FILLET FILLET STEP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQSYJ 10HARDNESS RATING,END END HARDNESS RATING A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF THE END(S) WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE. 2D AND 1B MODE REPLY22AC261AC20 BQSZD 07INDICATOR,CASEHARDENING,END END CASEHARDENING INDICATOR INDICATES WHETHER OR NOT AN OBJECT WITH FERROUS ALLOY ENDS HAS BEEN SUBJECTED TO A PROCESS WHEREBY THE END OUTER PORTION IS MADE SUBSTANTIALLY HARDER THAN THE INNER PORTION. SELECT REPLY CODE 10AA70 BQTCJ 04DIAMETER,FLAT FLAT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BQTDJ 04RADIUS,SPHERICAL,END END SPHERICAL RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQTFJ 04DEPTH,RADIUS,SPHERICAL SPHERICAL RADIUS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BQTGJ 04WIDTH,OUTSIDE,LARGEST LARGEST OUTSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BQTHJ 04DIAMETER,COUNTERSINK,TOP,LARGEST LARGEST TOP COUNTERSINK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BQTJJ 04DIAMETER,COUTERSINK,BOTTOM,LARGEST LARGEST BOTTOM COUNTERSINK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BQTKB 04ANGLE IN DEG,CHAMFER,LARGEST OUTSIDE DIAMETER LARGEST OUTSIDE DIAMETER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 BQTLB 04ANGLE IN DEG,CHAMFER,SMALLEST OUTSIDE DIAMETER SMALLEST OUTSIDE DIAMETER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 BQTMG 10DEVIATION,LIGHT LIGHT DEVIATION THE AMOUNT OF DEVIATION AND/OR BENDING OF AN INCOMING LIGHT RAY FROM ITS ORIGINAL PATH. FULL TEXT WRITE-IN 0 BQTNB 04ANGLE IN DEG,INCLUDED,TOP COUNTERSINK TOP COUNTERSINK INCLUDED ANGLE IN DEG NONE. 1B MODE REPLY 0 BQTPB 04ANGLE IN DEG,INCLUDED,BOTTOM COUNTERSINK BOTTOM COUNTERSINK INCLUDED ANGLE IN DEG NONE. 1B MODE REPLY 0 BQTQJ 04DEPTH,COUNTERBORE,TOP TOP COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BQTRJ 04DEPTH,COUNTERBORE,BOTTOM BOTTOM COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BQTSJ 04RADIUS,TOP,INSIDE DIAMETER INSIDE DIAMETER TOP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQTTJ 04RADIUS,BOTTOM,INSIDE DIAMETER INSIDE DIAMETER BOTTOM RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BQTWB 10ROTATION IN DEG,MINIMUM MINIMUM ROTATION IN DEG A MEASUREMENT OF THE SMALLEST DEGREE OF ROTATION. 1B MODE REPLY 0 BQTXJ T10RANGE,LOAD,STARTING STARTING LOAD RANGE THE STARTING LOAD MINIMUM AND MAXIMUM LIMITS FOR WHICH THE ITEM IS DESIGNED. 1D AND 1F MODE REPLY12AJ20 BQTYG 04ANGLE IN DEG,INCLUDED,TAPERED BORE TAPERED BORE INCLUDED ANGLE IN DEG NONE. FULL TEXT WRITE-IN 0 BQTZJ /D/ 04DIAMETER,INSIDE,SPRING AND BALL RETAINER SPRING AND BALL RETAINER INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BQWBJ 04DISTANCE FROM END TO NEAREST STEP DISTANCE FROM END TO NEAREST STEP NONE. 2D AND 1B MODE REPLY21AA051AC20 BQWCG /D/ 04CHAMFER/RADIUS OF OUTSIDE CORNER CHAMFER/RADIUS OF OUTSIDE CORNER NONE. FULL TEXT WRITE-IN 0 BQWDG /D/ 04CHAMFER/RADIUS OF INSIDE CORNER CHAMFER/RADIUS OF INSIDE CORNER NONE. FULL TEXT WRITE-IN 0 BQWFJ 04DIAMETER,HOLE,OIL OIL HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BQWGD 02DESIGN,HEAD,DIE DIE HEAD DESIGN THE DESIGN OF THE DIE HEAD. SELECT REPLY CODE 10AK54 BQWHD 19CHARACTERISTIC,MATERIAL MATERIAL CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC(S) OF THE MATERIAL. SELECT REPLY CODE 10AA62 BQWJD /D/ 07PREWETTING PRIOR TO APPLICATION PREWETTING PRIOR TO APPLICATION AN INDICATION OF WHETHER OR NOT PREWETTING IS REQUIRED PRIOR TO APPLICATION. SELECT REPLY CODE 10AE40 BQWKD /D/ 07CHASER,CUTTING,THREAD THREAD CUTTING CHASER AN INDICATION OF WHETHER OR NOT A THREAD CUTTING CHASER/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BQWLA 12QUANTITY,SET SET QUANTITY THE NUMBER OF SETS PROVIDED. 1A MODE REPLY 0 BQWMD 18TYPE,DEVICE,CUTTING CUTTING DEVICE TYPE INDICATES THE TYPE OF DEVICE USED FOR CUTTING. SELECT REPLY CODE 10AC82 BQWND /D/ 07CHAMBER,VACUUM VACUUM CHAMBER AN INDICATION OF WHETHER OR NOT A VACUUM CHAMBER IS INCLUDED. SELECT REPLY CODE 10AA49 BQWPJ 04LENGTH,OVERALL,VACUUM CHAMBER VACUUM CHAMBER OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE VACUUM CHAMBER. 2D AND 1B MODE REPLY21AA051AC20 BQWQJ 04DIAMETER,INSIDE,VACUUM CHAMBER VACUUM CHAMBER INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE VACUUM CHAMBER,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BQWRD 07REMOVABILITY,CHAMBER,VACUUM VACUUM CHAMBER REMOVABILITY AN INDICATION OF WHETHER OR NOT THE VACUUM CHAMBER IS REMOVABLE. SELECT REPLY CODE 10AC29 BQWSJ T04DIAMETER RANGE,WORKING WORKING DIAMETER RANGE THE RANGE OF DIAMETERS THE ITEM ACCOMMODATES. 1D AND 1F MODE REPLY11AA05 BQWTJ T04LENGTH RANGE,WORKING WORKING LENGTH RANGE THE MINIMUM AND MAXIMUM LIMITS OF THE WORKING LENGTH OF THE ITEM. 1D AND 1F MODE REPLY11AA05 BQWWJ A18TYPE AND QUANTITY,ELEMENT,WORKING WORKING ELEMENT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF WORKING ELEMENTS PROVIDED. 1D AND 1A MODE REPLY12AG25 BQWXD /D/ 07SHUT-OFF,HEATER,AUTOMATIC,LOW WATER LOW WATER AUTOMATIC HEATER SHUT-OFF AN INDICATION OF WHETHER OR NOT A LOW WATER AUTOMATIC HEATER SHUT-OFF IS INCLUDED. SELECT REPLY CODE 10AA49 BQWYD /D/ 07DEVICE,BLEEDER BLEEDER DEVICE AN INDICATION OF WHETHER OR NOT A BLEEDER DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 BQWZJ /D/ 04DISTANCE BETWEEN WORKING ELEMENTS DISTANCE BETWEEN WORKING ELEMENTS THE DISTANCE BETWEEN THE WORKING ELEMENTS. 2D AND 1B MODE REPLY21AA051AC20 BQXBJ /D/ 04DISTANCE FROM TABLE TOP TO SPINDLE DISTANCE FROM TABLE TOP TO SPINDLE THE DISTANCE FROM THE TOP OF THE TABLE TO THE SPINDLE. 2D AND 1B MODE REPLY21AA051AC20 BQXCJ 04DIAMETER BETWEEN FLANGES,SPINDLE SPINDLE DIAMETER BETWEEN FLANGES THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SPINDLE BETWEEN FLANGES,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BQXDJ 10DISPLACEMENT,PISTON PISTON DISPLACEMENT THE VOLUME DISPLACED BY A PISTON IN A SINGLE STROKE. 2D AND 1B MODE REPLY21AD421AC20 BQXFD /D/ 07GEAR,REDUCTION/REVERSE,INTEGRAL INTEGRAL REDUCTION/REVERSE GEAR AN INDICATION OF WHETHER OR NOT AN INTEGRAL REDUCTION AND REVERSE GEAR IS INCLUDED. SELECT REPLY CODE 10AA49 BQXGD 11METHOD,LUBRICATION,OUTBOARD DRIVE OUTBOARD DRIVE LUBRICATION METHOD THE MEANS USED TO LUBRICATE THE OUTBOARD DRIVE. SELECT REPLY CODE 10AG57 BQXHD 11METHOD,OPERATING,OUTBOARD DRIVE STEERING MECHANISM OUTBOARD DRIVE STEERING MECHANISM OPERATING METHOD THE MEANS BY WHICH THE OUTBOARD DRIVE STEERING MECHANISM IS OPERATED. SELECT REPLY CODE 10AG25 BQXJD 11METHOD,OPERATING,OUTBOARD DRIVE TILTING MECHANISM OUTBOARD DRIVE TILTING MECHANISM OPERATING METHOD THE MEANS BY WHICH THE OUTBOARD DRIVE TILTING MECHANISM IS OPERATED. SELECT REPLY CODE 10AG25 BQXKD /D/ 07BRAKE,LOCKING,OUTBOARD DRIVE OUTBOARD DRIVE LOCKING BRAKE AN INDICATION OF WHETHER OR NOT A LOCKING BRAKE IS INCLUDED ON THE OUTBOARD DRIVE. SELECT REPLY CODE 10AA49 BQXLD /D/ 07SKEG,PROTECTIVE,OUTBOARD DRIVE OUTBOARD DRIVE PROTECTIVE SKEG AN INDICATION OF WHETHER OR NOT A PROTECTIVE SKEG IS INCLUDED ON THE OUTBOARD DRIVE. SELECT REPLY CODE 10AA49 BQXMA 12QUANTITY,BLADE,PROPELLER PROPELLER BLADE QUANTITY THE NUMBER OF PROPELLER BLADES PROVIDED. 1A MODE REPLY 0 BQXNJ 04DIAMETER,BLADE,PROPELLER PROPELLER BLADE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR PROPELLER BLADE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BQXPJ 10PITCH,BLADE,PROPELLER PROPELLER BLADE PITCH THE DISTANCE THE PROPELLER BLADE ADVANCES IN ONE REVOLUTION. 2D AND 1B MODE REPLY21AA051AC20 BQXQD 05DIRECTION,ROTATION,PROPELLER PROPELLER ROTATION DIRECTION THE DIRECTION IN WHICH THE PROPELLER IS DESIGNED TO ROTATE,WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AA38 BQXRD /D/ 09MATERIAL,PROPELLER PROPELLER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PROPELLER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BQXSD 11METHOD,ATTACHMENT,PROPELLER PROPELLER ATTACHMENT METHOD THE MEANS USED TO ATTACH THE PROPELLER. SELECT REPLY CODE 10AB87 BQXTD /D/ 09MATERIAL,SHAFT,PROPELLER PROPELLER SHAFT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PROPELLER SHAFT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BQXWA /D/ 12QUANTITY,SECTION,PROPELLER SHAFT PROPELLER SHAFT SECTION QUANTITY THE NUMBER OF SECTIONS INCLUDED IN THE PROPELLER SHAFT. 1A MODE REPLY 0 BQXXD /D/ 18TYPE,JOINT,PROPELLER SHAFT SECTION PROPELLER SHAFT SECTION JOINT TYPE INDICATES THE TYPE OF PROPELLER SHAFT SECTION JOINT PROVIDED. SELECT REPLY CODE 10AC02 BQXYD /D/ 09MATERIAL,PONTOON PONTOON MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PONTOON IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BQXZJ /D/ 04LENGTH,OVERALL,PONTOON PONTOON OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF A PONTOON. 2D AND 1B MODE REPLY21AA051AC20 BQYBJ /D/ 04WIDTH,OVERALL,PONTOON PONTOON OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A PONTOON. 2D AND 1B MODE REPLY21AA051AC20 BQYCJ /D/ 04DEPTH,END,BOW,PONTOON PONTOON BOW END DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE PONTOON BOW END,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BQYDJ /D/ 04DISTANCE FROM SUPERSTRUCTURE TOP TO RUDDER BOTTOM DISTANCE FROM SUPERSTRUCTURE TOP TO RUDDER BOTTOM THE DISTANCE FROM THE TOP OF THE SUPERSTRUCTURE TO THE BOTTOM OF THE RUDDER. 2D AND 1B MODE REPLY21AA051AC20 BQYFD /D/ 09MATERIAL,RUDDER RUDDER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE RUDDER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BQYGA 12QUANTITY,SLING SLING QUANTITY THE NUMBER OF SLINGS PROVIDED. 1A MODE REPLY 0 BQYHA 12QUANTITY PER SLING,LEG LEG QUANTITY PER SLING THE NUMBER OF LEGS ON EACH SLING. 1A MODE REPLY 0 BQYJD /D/ 18TYPE,LEG,SLING SLING LEG TYPE INDICATES THE TYPE OF SLING LEG PROVIDED. SELECT REPLY CODE 10AK54 BQYKD /D/ 09MATERIAL,LEG,SLING SLING LEG MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SLING LEG IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BQYLG /D/ 04LENGTH BETWEEN TERMINAL BEARING SURFACES,LEG LEG LENGTH BETWEEN TERMINAL BEARING SURFACES A MEASUREMENT OF THE LONGEST DIMENSION BETWEEN THE TERMINAL BEARING SURFACES OF THE LEG,IN DISTINCTION FROM WIDTH. FULL TEXT WRITE-IN 0 BQYMD 18TYPE,SPREADER,SLING SLING SPREADER TYPE INDICATES THE TYPE OF SLING SPREADER PROVIDED. SELECT REPLY CODE 10AK54 BQYNA 12QUANTITY,NET NET QUANTITY THE NUMBER OF NETS PROVIDED. 1A MODE REPLY 0 BQYPD 18TYPE,NET NET TYPE INDICATES THE TYPE OF NET PROVIDED. SELECT REPLY CODE 10AK54 BQYQJ 04LENGTH,OVERALL,NET NET OVERALL LENGTH AN OVERALL MEASUREMENT OF THE LONGEST DIMENSION OF THE NET,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BQYRJ 04WIDTH,OVERALL,NET NET OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE NET,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BQYSJ 04DIAMETER,MEMBER,MESH,NET NET MESH MEMBER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A NET MESH MEMBER, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BQYTJ 04DIAMETER,ROPE,NET FRAME NET FRAME ROPE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A NET FRAME ROPE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BQYWJ /D/ 04LENGTH,LEG,NET NET LEG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE NET LEG,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BQYXJ 04DIAMETER,LEG,NET NET LEG DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A NET LEG,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BQYYD 18TYPE,MATERIAL,BACKING BACKING MATERIAL TYPE INDICATES THE TYPE OF BACKING MATERIAL PROVIDED. SELECT REPLY CODE 10AL60 BQYZJ 10CIRCUMFERENCE,INSIDE INSIDE CIRCUMFERENCE THE DISTANCE AROUND THE INSIDE SURFACE OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BQZBD /D/ 09MATERIAL,ITEM,FURNISHED FURNISHED ITEM MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FURNISHED ITEM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BQZCD 02DESIGN,MESH MESH DESIGN THE DESIGN OF THE MESH IN THE ITEM. SELECT REPLY CODE 10AK54 BQZDG /D/ 18TYPE AND SIZE,MEMBER,MESH MESH MEMBER TYPE AND SIZE INDICATES THE TYPE AND SIZE OF MESH MEMBER. FULL TEXT WRITE-IN 0 BQZFG /D/ 18TYPE AND SIZE,JACKSTAY JACKSTAY TYPE AND SIZE INDICATES THE TYPE AND SIZE OF JACKSTAY. FULL TEXT WRITE-IN 0 BQZGJ /D/ 04LENGTH,SECTION,OPEN CENTER OPEN CENTER SECTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE OPEN CENTER SECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BQZHJ /D/ 04WIDTH,SECTION,OPEN CENTER OPEN CENTER SECTION WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE OPEN CENTER SECTION,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BQZJJ 04DIAMETER,INSIDE,CORNER RING CORNER RING INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO SURFACES OF THE CORNER RING,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BQZKJ 04LENGTH,LINE,ATTACHED ATTACHED LINE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ATTACHED LINE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BQZLA /D/ 12QUANTITY,SPREADER SPREADER QUANTITY THE NUMBER OF SPREADERS PROVIDED. 1A MODE REPLY 0 BQZMD /D/ 07END,SLOTTED SLOTTED END AN INDICATION OF WHETHER OR NOT A SLOTTED END IS INCLUDED. SELECT REPLY CODE 10AA49 BQZND /D/ 07END,DRILLED DRILLED END AN INDICATION OF WHETHER OR NOT A DRILLED END IS INCLUDED. SELECT REPLY CODE 10AA49 BQZPA 12QUANTITY EACH END,HOLE HOLE QUANTITY EACH END THE NUMBER OF HOLES PROVIDED ON EACH END OF THE ITEM. 1A MODE REPLY 0 BRBGG 19CHARACTERISTIC,KEY KEY CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC(S) OF A KEY. FULL TEXT WRITE-IN 0 BRBHG 19CHARACTERISTIC,ADAPTER ADAPTER CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC(S) OF AN ADAPTER. FULL TEXT WRITE-IN 0 BRBJD /D/ 07GRIPPER,SCREW,EXTERNAL EXTERNAL SCREW GRIPPER AN INDICATION OF WHETHER OR NOT AN EXTERNAL SCREW GRIPPER IS PROVIDED. SELECT REPLY CODE 10AB22 BRBKD /D/ 07TIP,MAGNETIC MAGNETIC TIP AN INDICATION OF WHETHER OR NOT A MAGNETIC TIP IS PROVIDED. SELECT REPLY CODE 10AB22 BRBLD /D/ 07GRIP,WRENCH WRENCH GRIP AN INDICATION OF WHETHER OR NOT A WRENCH GRIP IS PROVIDED. SELECT REPLY CODE 10AB22 BRBMD /D/ 07EXTENSION,BLADE THROUGH HANDLE BLADE THROUGH HANDLE EXTENSION AN INDICATION OF WHETHER OR NOT A BLADE EXTENSION THROUGH THE HANDLE IS PROVIDED. SELECT REPLY CODE 10AB22 BRBND 07REMOVABILITY,BLADE BLADE REMOVABILITY AN INDICATION OF WHETHER OR NOT A BLADE IS REMOVABLE. SELECT REPLY CODE 10AC29 BRBPD 18TYPE,RACHET RACHET TYPE INDICATES THE TYPE OF RACHET. SELECT REPLY CODE 10AJ57 BRBQD 18TYPE,RETURN RETURN TYPE INDICATES THE TYPE OF RETURN. SELECT REPLY CODE 10AN38 BRBRD /D/ 07SLEEVE,CENTERING CENTERING SLEEVE AN INDICATION OF WHETHER OR NOT A CENTERING SLEEVE IS PROVIDED. SELECT REPLY CODE 10AB22 BRBSD /D/ 07HANDLE,MAGAZINE MAGAZINE HANDLE AN INDICATION OF WHETHER OR NOT A MAGAZINE HANDLE IS INCLUDED. SELECT REPLY CODE 10AA49 BRBTJ 04DIAMETER CAPACITY DIAMETER CAPACITY THE DIAMETER CAPACITY OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BRBWJ /D/ 04THICKNESS,KEY KEY THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A KEY,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BRBXJ 04DIAMETER FOR WHICH DESIGNED,BIT,SMALLEST SMALLEST BIT DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST BIT FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BRBYD /D/ 07FEATURE,BLADE,BANKED BANKED BLADE FEATURE AN INDICATION OF WHETHER OR NOT A BANKED BLADE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BRBZD /D/ 07FEATURE,BLADE,CURVED CURVED BLADE FEATURE AN INDICATION OF WHETHER OR NOT A CURVED BLADE IS PROVIDED. SELECT REPLY CODE 10AB22 BRCBD 19FINISH,SURFACE,BLADE BLADE SURFACE FINISH AN ADDITIONAL FINISHING PROCESS BY WHICH THE SURFACE OF A BLADE IS ALTERED IN RESPECT TO POLISHING,GRINDING,AND THE LIKE. SELECT REPLY CODE 10AA41 BRCCD /D/ 07COMPARTMENT,BLADE BLADE COMPARTMENT AN INDICATION OF WHETHER OR NOT A BLADE COMPARTMENT IS PROVIDED. SELECT REPLY CODE 10AB22 BRCDL 16STYLE,SOCKET,ELECTRON TUBE ELECTRON TUBE SOCKET STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ELECTRON TUBE SOCKET. 1L MODE REPLY 0 BRCFD 18TYPE FOR WHICH DESIGNED,TOOL TOOL TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF TOOL FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AJ57 BRCGG 04SIZE FOR WHICH DESIGNED,CONTACT CONTACT SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE CONTACT FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 BRCHD /D/ 07FEATURE,DIE,REVOLVING REVOLVING DIE FEATURE AN INDICATION OF WHETHER OR NOT A REVOLVING DIE FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BRCJD /D/ 07JAW,CUTTING CUTTING JAW AN INDICATION OF WHETHER OR NOT A CUTTING JAW IS PROVIDED. SELECT REPLY CODE 10AB22 BRCKD /D/ 07STRIPPER,WIRE WIRE STRIPPER AN INDICATION OF WHETHER OR NOT A WIRE STRIPPER IS PROVIDED. SELECT REPLY CODE 10AB22 BRCLG 18TYPE FOR WHICH DESIGNED,TUBE,ELECTRON ELECTRON TUBE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF ELECTRON TUBE FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 BRCMD 18TYPE FOR WHICH DESIGNED,LAMP LAMP TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF LAMP FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AD48 BRCNJ 04DIAMETER ACCOMMODATED,BULB BULB DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE BULB,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BRCPD /D/ 09MATERIAL,END,EXTRACTOR EXTRACTOR END MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE EXTRACTOR END IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BRCQD /D/ 07HANDLE,SECTIONAL SECTIONAL HANDLE AN INDICATION OF WHETHER OR NOT A SECTIONAL HANDLE IS PROVIDED. SELECT REPLY CODE 10AB22 BRCRD /D/ 07HOLE,MOUNTING MOUNTING HOLE AN INDICATION OF WHETHER OR NOT A MOUNTING HOLE/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 BRCSD /D/ 07POST,GUIDE GUIDE POST AN INDICATION OF WHETHER OR NOT A GUIDE POST IS PROVIDED. SELECT REPLY CODE 10AB22 BRCTJ A03DESIGNATION,SIZE SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1D AND 1A MODE REPLY13AF81 BRCWG 04SIZE FOR WHICH DESIGNED,SPIKE SPIKE SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE SPIKE FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 BRCXJ 04WIDTH,END,WORKING WORKING END WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BRCYA /D/ 12QUANTITY,BLADE,EXTRA EXTRA BLADE QUANTITY THE NUMBER OF EXTRA BLADES PROVIDED. 1A MODE REPLY 0 BRCZL 16STYLE,END,TOOL HEAD TOOL HEAD END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TOOL HEAD END. 1L MODE REPLY 0 BRDBJ 04DIAMETER ACCOMMODATED,MAXIMUM,CABLE CABLE MAXIMUM DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE CABLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BRDCL 16STYLE,END,BUTT BUTT END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BUTT END. 1L MODE REPLY 0 BRDDD /D/ 07ATTACHMENT,BODY BODY ATTACHMENT AN INDICATION OF WHETHER OR NOT A BODY ATTACHMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BRDFL /D/ 16STYLE,ATTACHMENT,BODY BODY ATTACHMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BODY ATTACHMENT. 1L MODE REPLY 0 BRDGJ /D/ 04DISTANCE BETWEEN CENTER OF LEFT LEG SOCKET/BALL AND END OF BOTTOM LEG DISTANCE BETWEEN CENTER OF LEFT LEG SOCKET/BALL AND END OF BOTTOM LEG NONE. 2D AND 1B MODE REPLY21AA051AC20 BRDHJ /D/ 04DISTANCE FROM FLANGE FACE TO CENTER OF BALL SOCKET DISTANCE FROM FLANGE FACE TO CENTER OF BALL SOCKET NONE. 2D AND 1B MODE REPLY21AA051AC20 BRDJJ /D/ 04DISTANCE FROM FLANGE FACE TO CENTER OF LEG SOCKET DISTANCE FROM FLANGE FACE TO CENTER OF LEG SOCKET NONE. 2D AND 1B MODE REPLY21AA051AC20 BRDKJ /D/ 04DISTANCE FROM CENTER OF TOP LEG BALL TO FACE OF CENTER LEG FLANGE DISTANCE FROM CENTER OF TOP LEG BALL TO FACE OF CENTER LEG FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BRDLJ 04HEIGHT,RETRACTED RETRACTED HEIGHT A MEASUREMENT FROM THE BOTTOM OF THE MOUNTING BASE TO THE TOP OF THE ITEM,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BRDMJ /D/ 04DISTANCE FROM FACE OF CENTER LEG FLANGE TO FACE OF BOTTOM LEG FLANGE DISTANCE FROM FACE OF CENTER LEG FLANGE TO FACE OF BOTTOM LEG FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BRDNJ /D/ 04DISTANCE FROM CENTER OF BOTTOM LEG SOCKET/BALL TO FACE OF RIGHT LEG DISTANCE FROM CENTER OF BOTTOM LEG SOCKET/BALL TO FACE OF RIGHT LEG NONE. 2D AND 1B MODE REPLY21AA051AC20 BRDPJ /D/ 04DISTANCE FROM TOP LEG SOCKET/BALL TO FACE OF RIGHT LEG DISTANCE FROM TOP LEG SOCKET/BALL TO FACE OF RIGHT LEG NONE. 2D AND 1B MODE REPLY21AA051AC20 BRDQB /D/ 04ANGLE IN DEG,FIRST LEG TO SECOND LEG FIRST LEG TO SECOND LEG ANGLE IN DEG NONE. 1B MODE REPLY 0 BRDRB /D/ 04ANGLE IN DEG,SECOND LEG TO THIRD LEG SECOND LEG TO THIRD LEG ANGLE IN DEG NONE. 1B MODE REPLY 0 BRDSB /D/ 04ANGLE IN DEG,THIRD LEG TO FIRST LEG THIRD LEG TO FIRST LEG ANGLE IN DEG NONE. 1B MODE REPLY 0 BRDTD 11METHOD,LEVELING LEVELING METHOD THE MEANS USED TO LEVEL THE ITEM. SELECT REPLY CODE 10AA62 BRDWB 10CONSTRUCTION IN PERCENT,LAMINATION LAMINATION CONSTRUCTION IN PERCENT AN INDICATION OF THE AMOUNT OF LAMINATION CONSTRUCTION,EXPRESSED IN PERCENT. 1B MODE REPLY 0 BRDXA 12QUANTITY,LAMINATION LAMINATION QUANTITY THE NUMBER OF LAMINATIONS PROVIDED. 1A MODE REPLY 0 BRDYJ 04THICKNESS,LAMINATION LAMINATION THICKNESS THE DISTANCE BETWEEN THE OPPOSITE FLAT SURFACES OF THE INDIVIDUAL LAMINATIONS. 2D AND 1B MODE REPLY21AA051AC20 BRDZD 05DIRECTION,EDGE,CORRUGATED CORRUGATED EDGE DIRECTION THE DIRECTION IN WHICH THE CORRUGATED EDGES ARE TURNED IN RELATION TO EACH OTHER WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AC72 BRFBJ 10AREA,COVERING COVERING AREA THE AREA,PER UNIT OF WEIGHT,THE ITEM WILL COVER. 1D AND 1B MODE REPLY12AG67 BRFCD 11METHOD,COATING COATING METHOD THE MEANS BY WHICH THE COATING IS APPLIED. SELECT REPLY CODE 10AK01 BRFDJ 10WEIGHT PER UNIT MEASURE WEIGHT PER UNIT MEASURE THE WEIGHT OF THE ITEM WITH RESPECT TO A UNIT OF MEASURE. 1D AND 1B MODE REPLY12AG69 BRFFD /D/ 11METHOD,CASTING CASTING METHOD THE MEANS USED IN CASTING THE ITEM. SELECT REPLY CODE 10AA62 BRFGJ 04WIDTH,MAXIMUM,ROLL ROLL MAXIMUM WIDTH THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ROLL,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BRFHJ 04DIAMETER,MAXIMUM,ROLL ROLL MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ROLL,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BRFJJ 04LENGTH,CUTOFF,ROLL ROLL CUTOFF LENGTH A MEASUREMENT OF THE LONGEST CUTOFF DIMENSION OF A ROLL,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BRFKJ 04LENGTH,MAXIMUM,ROLL ROLL MAXIMUM LENGTH THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF THE ROLL,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BRFLJ 04LENGTH,MAXIMUM MAXIMUM LENGTH THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF THE ITEM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BRFMJ 04WIDTH,MINIMUM MINIMUM WIDTH THE MINIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ITEM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BRFNJ 04LENGTH,MAXIMUM,TRANSFER AREA TRANSFER AREA MAXIMUM LENGTH THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF THE TRANSFER AREA,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BRFPJ 04WIDTH,MAXIMUM,TRANSFER AREA TRANSFER AREA MAXIMUM WIDTH THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TRANSFER AREA,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BRFQJ 04WIDTH,INSIDE,BED BED INSIDE WIDTH AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BED,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BRFRJ 04LENGTH,INSIDE,BED BED INSIDE LENGTH A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF THE BED,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BRFSD /D/ 07COUNTER,COPY COPY COUNTER AN INDICATION OF WHETHER OR NOT A COPY COUNTER IS INCLUDED. SELECT REPLY CODE 10AA49 BRFTD 18TYPE,ROLLER,INKING INKING ROLLER TYPE INDICATES THE TYPE OF INKING ROLLER(S) PROVIDED. SELECT REPLY CODE 10AC68 BRFWA 12QUANTITY,LAMP,PRINTING PRINTING LAMP QUANTITY THE NUMBER OF PRINTING LAMPS PROVIDED. 1A MODE REPLY 0 BRFXJ /D/ 10INTENSITY IN WATTS PER INCH,LAMP,PRINTING PRINTING LAMP INTENSITY IN WATTS PER INCH THE PREDETERMINED LIGHT INTENSITY (UNITS OF ILLUMINATION) AT WHICH THE ITEM IS DESIGNED TO PRINT,EXPRESSED IN WATTS PER INCH. 1D AND 1B MODE REPLY11AC20 BRFYD 08LOCATION,DELIVERY,PRINT PRINT DELIVERY LOCATION INDICATES THE LOCATION OF THE PRINT DELIVERY IN RELATION TO THE ITEM. SELECT REPLY CODE 10AJ91 BRFZD /D/ 07TRIMMER TRIMMER AN INDICATION OF WHETHER OR NOT A TRIMMER IS INCLUDED. SELECT REPLY CODE 10AA49 BRGBD 14SHAPE,PUNCH PUNCH SHAPE THE PHYSICAL CONFIGURATION OF THE PUNCH. SELECT REPLY CODE 10AD07 BRGCJ 04THICKNESS ACCOMMODATED,WORK,MAXIMUM MAXIMUM WORK THICKNESS ACCOMMODATED THE MAXIMUM MEASUREMENT OF THE SMALLEST DIMENSION OF THE WORK THE ITEM WILL ACCOMMODATE,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 BRGDJ 04DIAMETER ACCOMMODATED,DRILL,MAXIMUM MAXIMUM DRILL DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DRILL THE ITEM WILL ACCOMMODATE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BRGFJ 04DISTANCE FROM SHEET EDGE TO DRILL CENTER,MAXIMUM MAXIMUM DISTANCE FROM SHEET EDGE TO DRILL CENTER THE MAXIMUM DISTANCE FROM THE EDGE OF THE SHEET TO THE CENTER OF THE DRILL. 1D AND 1B MODE REPLY11AA05 BRGPD 19POSITION,LIFTING LIFTING POSITION THE POSITION IN WHICH THE ITEM DOES THE LIFTING. SELECT REPLY CODE 10AM84 BRGQD 18TYPE,ACTION,GRIPPING GRIPPING ACTION TYPE INDICATES THE TYPE OF THE GRIPPING ACTION USED BY THE ITEM. SELECT REPLY CODE 10AJ27 BRGRJ 04LENGTH ACCOMMODATED,MATERIAL MATERIAL LENGTH ACCOMMODATED A MEASUREMENT OF THE LONGEST DIMENSION OF THE MATERIAL THE ITEM WILL ACCOMMODATE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BRGSJ /D/ 04WIDTH ACCOMMODATED,MATERIAL MATERIAL WIDTH ACCOMMODATED PLEASE USE MRC BBGD IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 BRGTJ 04HEIGHT,FORK FORK HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE FORK, IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BRGWJ 04DIAMETER,OUTSIDE,MAXIMUM MAXIMUM OUTSIDE DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BRHBG 19CLASS FOR WHICH SUITABLE,VESSEL VESSEL CLASS FOR WHICH SUITABLE THE CLASS OF VESSEL FOR WHICH THE ITEM IS SUITABLE. FULL TEXT WRITE-IN 0 BRHCJ /D/A19NUMBER,ASSOCIATION,TIRE AND RIM TIRE AND RIM ASSOCIATION NUMBER A NUMBER ASSIGNED TO THE ITEM BY THE TIRE AND RIM ASSOCIATION FOR IDENTIFICATION. 1D AND 1A MODE REPLY13AN39 BRHDD 14SHAPE,ACCOMMODATION,HOLE HOLE ACCOMMODATION SHAPE THE PHYSICAL CONFIGURATION OF THE HOLE ACCOMMODATION. SELECT REPLY CODE 10AD07 BRHFD 18TYPE,BASE,RUBBER RUBBER BASE TYPE INDICATES THE TYPE OF RUBBER BASE PROVIDED. SELECT REPLY CODE 10AJ57 BRHGD 18TYPE,TENSION,SPRING SPRING TENSION TYPE INDICATES THE TENSION TYPE OF THE SPRING. SELECT REPLY CODE 10AK09 BRHHD /D/ 07ACCOMMODATION,CORE,VALVE VALVE CORE ACCOMMODATION AN INDICATION OF WHETHER OR NOT A VALVE CORE ACCOMMODATION IS INCLUDED. SELECT REPLY CODE 10AA49 BRHJD 03DESIGNATION,SIZE,BORE BORE SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE BORE IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. SELECT REPLY CODE 10AF81 BRHKD /D/ 19AGENT,DISPENSING DISPENSING AGENT THE MEDIUM THROUGH WHICH THE LIQUID IS DISPERSED. SELECT REPLY CODE 10AF11 BRHLJ /D/ 04LENGTH,SURFACE,BEARING,NUT NUT BEARING SURFACE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BRHMG 04SIZE FOR WHICH DESIGNED,VALVE VALVE SIZE FOR WHICH DESIGNED NONE. FULL TEXT WRITE-IN 0 BRHNJ /D/ 04WIDTH,END,LIP LIP END WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BRHPA 13THREAD SIZE,CAP CAP THREAD SIZE NONE. 1A MODE REPLY 0 BRHQJ 04HEIGHT,EFFECTIVE EFFECTIVE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BRHRJ 04DISTANCE FROM CENTER TO END DISTANCE FROM CENTER TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 BRHSB /D/ 04ANGLE IN DEG,OUTSIDE OUTSIDE ANGLE IN DEG NONE. 1B MODE REPLY 0 BRHTD /D/ 19FORM,ISSUE ISSUE FORM AN INDICATION OF THE FORM IN WHICH THE ITEM IS ISSUED. PLEASE USE MRC AXGW IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AE98 BRHWD /D/ 18TYPE FOR WHICH DESIGNED,PRESSURE PRESSURE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF PRESSURE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL77 BRHXD /D/ 18TYPE ACCOMMODATED,RIM RIM TYPE ACCOMMODATED INDICATES THE TYPE OF RIM THE ITEM WILL ACCOMMODATE. SELECT REPLY CODE 10AK54 BRHYG /D/ 04SIZE ACCOMMODATED,TIRE TIRE SIZE ACCOMMODATED DESIGNATES THE TIRE SIZE THE ITEM WILL ACCOMMODATE. FULL TEXT WRITE-IN 0 BRHZD /D/ 07ADJUSTABILITY,WIDTH WIDTH ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE WIDTH IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BRJBA /D/ 19NUMBER,CODE,INDUSTRIAL INDUSTRIAL CODE NUMBER THE STANDARD CODE NUMBER USED BY INDUSTRY TO IDENTIFY THE ITEM. 1A MODE REPLY 0 BRJCJ 04LENGTH,UNIT,CURING CURING UNIT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CURING UNIT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BRJDJ 04WIDTH,UNIT,CURING CURING UNIT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CURING UNIT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BRJFG /D/ 18TYPE AND QUANTITY,CLAMP CLAMP TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF CLAMPS PROVIDED. FULL TEXT WRITE-IN 0 BRJGD /D/ 07FEATURE,PULL,CENTER HOLE CENTER HOLE PULL FEATURE AN INDICATION OF WHETHER OR NOT A CENTER HOLE PULL FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BRJHJ 04DISTANCE,RISE RISE DISTANCE THE DISTANCE THE ITEM WILL RISE FROM THE RETRACTED POSITION. 2D AND 1B MODE REPLY21AA051AC20 BRJJD /D/ 07CAP,EXTENSION EXTENSION CAP AN INDICATION OF WHETHER OR NOT AN EXTENSION CAP IS INCLUDED. SELECT REPLY CODE 10AA49 BRJKD 18TYPE,PUMP PUMP TYPE INDICATES THE TYPE OF PUMP PROVIDED. SELECT REPLY CODE 10AK95 BRJLD /D/ 07GEAR GEAR AN INDICATION OF WHETHER OR NOT A GEAR IS PROVIDED. SELECT REPLY CODE 10AB22 BRJMD 18TYPE,LOAD,LOWERING UNDER LOWERING UNDER LOAD TYPE INDICATES THE TYPE OF LOWERING UNDER LOAD PROVIDED ON THE ITEM. SELECT REPLY CODE 10AK53 BRJND /D/ 07LIFT,FOOT FOOT LIFT AN INDICATION OF WHETHER OR NOT A FOOT LIFT IS PROVIDED. SELECT REPLY CODE 10AB22 BRJPD 18TYPE,LIFT,FOOT FOOT LIFT TYPE INDICATES THE TYPE OF FOOT LIFT PROVIDED. SELECT REPLY CODE 10AE15 BRJQD /D/ 07BAR,LINING,SQUARE HANDLE SOCKET SQUARE HANDLE SOCKET LINING BAR AN INDICATION OF WHETHER OR NOT A SQUARE HANDLE SOCKET LINING BAR IS PROVIDED. SELECT REPLY CODE 10AB22 BRJRD 18TYPE,CONTROL,SELF-LOWERING SELF-LOWERING CONTROL TYPE INDICATES THE TYPE OF SELF-LOWERING CONTROL PROVIDED. SELECT REPLY CODE 10AL37 BRJSD /D/ 07MECHANISM,RATCHET RATCHET MECHANISM AN INDICATION OF WHETHER OR NOT A RATCHET MECHANISM IS PROVIDED. SELECT REPLY CODE 10AB22 BRJTD 14SHAPE,PIKE PIKE SHAPE THE PHYSICAL CONFIGURATION OF THE PIKE. SELECT REPLY CODE 10AD07 BRJWD /D/ 07HOOK,PIKE PIKE HOOK AN INDICATION OF WHETHER OR NOT A PIKE HOOK IS PROVIDED. SELECT REPLY CODE 10AB22 BRJXD /D/ 07GUARD,PIKE PIKE GUARD AN INDICATION OF WHETHER OR NOT A PIKE GUARD IS PROVIDED. SELECT REPLY CODE 10AB22 BRJYJ /D/ 10WEIGHT,HEAD HEAD WEIGHT A RELATIVE MEASURE OF THE MASS OF A HEAD WITH RESPECT TO ITS DENSITY. 2D AND 1B MODE REPLY22AB161AC20 BRJZD /D/ 07GAGE,ADJUSTABLE ADJUSTABLE GAGE AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE GAGE IS PROVIDED. SELECT REPLY CODE 10AB22 BRKBJ /D/ 04SIZE AND TYPE ACCOMMODATED,DEVICE,FASTENING FASTENING DEVICE SIZE AND TYPE ACCOMMODATED DESIGNATES THE SIZE AND TYPE OF THE FASTENING DEVICE THE ITEM WILL ACCOMMODATE. 2D AND 1B MODE REPLY21AA052AE36 BRKCG 19NAME,CHARACTER CHARACTER NAME AN INDICATION OF THE NAME OF THE CHARACTER(S). FULL TEXT WRITE-IN 0 BRKDD /D/ 07HANDLE,ANGLE,ADJUSTABLE ADJUSTABLE ANGLE HANDLE AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE ANGLE HANDLE IS PROVIDED. SELECT REPLY CODE 10AB22 BRKFD /D/ 07HANDLE,HOLLOW HOLLOW HANDLE AN INDICATION OF WHETHER OR NOT A HOLLOW HANDLE IS PROVIDED. SELECT REPLY CODE 10AB22 BRKGA 12QUANTITY,DRILL,FURNISHED FURNISHED DRILL QUANTITY THE NUMBER OF DRILLS FURNISHED WITH THE ITEM. 1A MODE REPLY 0 BRKHG 04SIZE ACCOMMODATED,MATERIAL MATERIAL SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE MATERIAL THE ITEM WILL ACCOMMODATE. FULL TEXT WRITE-IN 0 BRKJD /D/ 07FEATURE,SPEED,TWO TWO SPEED FEATURE AN INDICATION OF WHETHER OR NOT A TWO SPEED FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BRKKD /D/ 07HANDLE,SIDE SIDE HANDLE AN INDICATION OF WHETHER OR NOT A SIDE HANDLE IS PROVIDED. SELECT REPLY CODE 10AB22 BRKLG 03DESIGNATION,SIZE,SOCKET SOCKET SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE SOCKET IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. FULL TEXT WRITE-IN 0 BRKMG /D/ 03DESIGNATION,SIZE,REDUCING SOCKET REDUCING SOCKET SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE REDUCING SOCKET IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. FULL TEXT WRITE-IN 0 BRKND /D/ 07RATCHET,REVERSIBLE REVERSIBLE RATCHET AN INDICATION OF WHETHER OR NOT A REVERSIBLE RATCHET IS PROVIDED. SELECT REPLY CODE 10AB22 BRKPJ /D/ 04WIDTH BETWEEN POINTS,BLADE BLADE WIDTH BETWEEN POINTS NONE. 2D AND 1B MODE REPLY21AA051AC20 BRKQL /D/ 16STYLE DESIGNATOR,KNIFE KNIFE STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE KNIFE. 1L MODE REPLY 0 BRKRD 10DUTY RATING DUTY RATING THE DUTY FOR WHICH THE ITEM IS RATED. SELECT REPLY CODE 10AF07 BRKSJ A18TYPE AND QUANTITY,BLADE BLADE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF BLADES PROVIDED. 1D AND 1A MODE REPLY12AJ46 BRKTD /D/ 07GUARD,BLADE BLADE GUARD AN INDICATION OF WHETHER OR NOT A BLADE GUARD IS PROVIDED. SELECT REPLY CODE 10AB22 BRKWD /D/ 07NOTCH,EXTENSION,BLADE BLADE EXTENSION NOTCH AN INDICATION OF WHETHER OR NOT A BLADE EXTENSION NOTCH/ES/ IS PROVIDED. SELECT REPLY CODE 10AB22 BRKXA 12QUANTITY,BLADE,HANDLE STORAGE HANDLE STORAGE BLADE QUANTITY THE NUMBER OF BLADES INCLUDED IN THE HANDLE STORAGE SPACE. 1A MODE REPLY 0 BRKYD /D/ 07DEVICE,OPENING,SPRING SPRING OPENING DEVICE AN INDICATION OF WHETHER OR NOT A SPRING OPENING DEVICE IS PROVIDED. SELECT REPLY CODE 10AB22 BRKZD /D/ 07CLEVIS CLEVIS AN INDICATION OF WHETHER OR NOT A CLEVIS IS PROVIDED. SELECT REPLY CODE 10AB22 BRLBJ 10SIZE,HOLE,SQUARE SQUARE HOLE SIZE DESIGNATES THE SIZE OF THE SQUARE HOLE. 2D AND 1B MODE REPLY21AA051AC20 BRLCA 04THICKNESS FOR WHICH DESIGNED,GAGE,BLADE BLADE GAGE THICKNESS FOR WHICH DESIGNED THE MEASUREMENT OF THE SMALLEST DIMENSION OF THE BLADE GAGE FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM LENGTH OR WIDTH. 1A MODE REPLY 0 BRLDF /D/T12QUANTITY PER INCH RANGE,POINT POINT QUANTITY PER INCH RANGE AN INDICATION OF THE MINIMUM AND MAXIMUM NUMBER OF POINTS PER INCH. 1F MODE REPLY 0 BRLFL 16STYLE DESIGNATOR,SCRAPER SCRAPER STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SCRAPER. 1L MODE REPLY 0 BRLGD 18TYPE,BRACKET,ROLLER ROLLER BRACKET TYPE INDICATES THE TYPE OF ROLLER BRACKET PROVIDED. SELECT REPLY CODE 10AK54 BRLHD /D/ 07HOOK,SUSPENSION,WIRE WIRE SUSPENSION HOOK AN INDICATION OF WHETHER OR NOT A WIRE SUSPENSION HOOK IS INCLUDED. SELECT REPLY CODE 10AA49 BRLJD /D/ 07ROD,TROUSER TROUSER ROD AN INDICATION OF WHETHER OR NOT A TROUSER ROD IS INCLUDED. SELECT REPLY CODE 10AA49 BRLKD /D/ 09MATERIAL,SLAT SLAT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SLAT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BRLLD 01COLOR,SLAT SLAT COLOR THE HUE OR TINT OF THE SLAT. SELECT REPLY CODE 10AD06 BRLMA 12QUANTITY,TAPE TAPE QUANTITY THE NUMBER OF TAPES PROVIDED. 1A MODE REPLY 0 BRLND 01COLOR,TAPE TAPE COLOR THE HUE OR TINT OF THE TAPE. SELECT REPLY CODE 10AD06 BRLPD 18TYPE,OPERATION,LIFT LIFT OPERATION TYPE INDICATES THE TYPE OF LIFT USED TO OPERATE THE ITEM. SELECT REPLY CODE 10AK54 BRLQD 18TYPE,LOCK,LIFTING CORD LIFTING CORD LOCK TYPE INDICATES THE TYPE OF LIFTING CORD LOCK PROVIDED. SELECT REPLY CODE 10AE36 BRLRD 18TYPE,DEVICE,TILTING TILTING DEVICE TYPE INDICATES THE TYPE OF DEVICE USED FOR TILTING THE ITEM. SELECT REPLY CODE 10AK54 BRLSD /D/ 07ROD,DRAPERY DRAPERY ROD AN INDICATION OF WHETHER OR NOT A DRAPERY ROD IS INCLUDED. SELECT REPLY CODE 10AA49 BRLTD 18TYPE,BRACKET,HANGER HANGER BRACKET TYPE INDICATES THE TYPE OF HANGER BRACKET PROVIDED. SELECT REPLY CODE 10AK54 BRLWD 18TYPE,COTTON COTTON TYPE INDICATES THE TYPE OF COTTON PROVIDED. SELECT REPLY CODE 10AH43 BRLXD /D/ 07STRAPS,CROSS,SOLID WOVEN SOLID WOVEN CROSS STRAPS AN INDICATION OF WHETHER OR NOT SOLID WOVEN CROSS STRAPS ARE INCLUDED. SELECT REPLY CODE 10AA49 BRLYJ 04WIDTH ACCOMMODATED,SLAT SLAT WIDTH ACCOMMODATED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SLAT THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BRLZJ 04WIDTH,STRAP,SIDE SIDE STRAP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SIDE STRAP,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BRMBJ 04WIDTH,STRAP,CROSS CROSS STRAP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CROSS STRAP,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BRMCJ 04DISTANCE BETWEEN CROSS STRAPS DISTANCE BETWEEN CROSS STRAPS THE DISTANCE FROM ONE CROSS STRAP TO THE OTHER. 2D AND 1B MODE REPLY21AA051AC20 BRMDD /D/ 18TYPE FOR WHICH DESIGNED,CHAIR/STOOL CHAIR/STOOL TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF CHAIR OR STOOL FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AC55 BRMFJ 04LENGTH,OVERALL,BODY BELT BODY BELT OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BRMGJ 04DISTANCE BETWEEN D RINGS DISTANCE BETWEEN D RINGS NONE. 2D AND 1B MODE REPLY21AA051AC20 BRMHJ 04WIDTH,BELT,BODY BODY BELT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BRMJJ 04WIDTH,PAD,CUSHION CUSHION PAD WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BRMKJ 04LENGTH,PAD,CUSHION CUSHION PAD LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BRMLD /D/ 07HARDWARE,NONSPARKING NONSPARKING HARDWARE AN INDICATION OF WHETHER OR NOT NONSPARKING HARDWARE IS INCLUDED. USE MRC CBBL WITH REPLY GLF. SELECT REPLY CODE 10AA49 BRMMG 04SIZE,WAIST WAIST SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE WAIST. FULL TEXT WRITE-IN 0 BRMNJ 04WIDTH,WAISTBAND WAISTBAND WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BRMPJ 04LENGTH,OVERALL,WAISTBAND WAISTBAND OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BRMQD 07ADJUSTABILITY,STRAP,SHOULDER SHOULDER STRAP ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE SHOULDER STRAP IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BRMRD 11METHOD,ADJUSTMENT,WAISTBAND WAISTBAND ADJUSTMENT METHOD THE MEANS PROVIDED TO ADJUST THE WAISTBAND. SELECT REPLY CODE 10AL41 BRMSD /D/ 07SUPPORT,LEG,ADJUSTABLE ADJUSTABLE LEG SUPPORT AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE LEG SUPPORT(S) IS FURNISHED. SELECT REPLY CODE 10AA55 BRMTD /D/ 07LIFELINE LIFELINE AN INDICATION OF WHETHER OR NOT A LIFELINE IS INCLUDED. SELECT REPLY CODE 10AA49 BRMWD /D/ 11METHOD,ATTACHMENT,D-RING D-RING ATTACHMENT METHOD THE MEANS USED TO ATTACH THE D-RING TO THE ITEM. SELECT REPLY CODE 10AB47 BRMXD /D/ 09MATERIAL,LINE LINE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LINE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BRMYD /D/ 07STRAP/PAD STRAP/PAD AN INDICATION OF WHETHER OR NOT STRAPS AND PADS ARE PROVIDED. SELECT REPLY CODE 10AB22 BRMZD /D/ 09MATERIAL,CUSHION,INNER INNER CUSHION MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INNER CUSHION IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BRNBL 16STYLE DESIGNATOR,FRONT FRONT STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FRONT. 1L MODE REPLY 0 BRNCD /D/ 09MATERIAL,BRIDGE BRIDGE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BRIDGE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BRNDD /D/ 17SURFACE TREATMENT,BRIDGE BRIDGE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE BRIDGE SURFACE. SELECT REPLY CODE 10AD09 BRNFD /D/ 09MATERIAL,RIM RIM MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE RIM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BRNGJ 04LENGTH,EFFECTIVE,CENTER TO CENTER CENTER TO CENTER EFFECTIVE LENGTH A MEASUREMENT OF THE DISTANCE BETWEEN THE CENTERS OF TWO HOLES THAT DETERMINES THE EFFECTIVE LENGTH OF AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 BRNHJ 04WIDTH AT PISTON CONNECTING END,BODY BODY WIDTH AT PISTON CONNECTING END A MEASUREMENT OF THE WIDTH OF THE BODY OF AN ITEM AT THE PISTON CONNECTING END. 2D AND 1B MODE REPLY21AA051AC20 BRNJJ 04WIDTH AT SHAFT CONNECTING END,BODY BODY WIDTH AT SHAFT CONNECTING END A MEASUREMENT OF THE WIDTH OF THE BODY OF AN ITEM AT THE SHAFT CONNECTING END. 2D AND 1B MODE REPLY21AA051AC20 BRNKJ 04THICKNESS AT PISTON CONNECTING END,BODY BODY THICKNESS AT PISTON CONNECTING END A MEASUREMENT OF THE THICKNESS OF THE BODY OF AN ITEM AT THE PISTON CONNECTING END. 2D AND 1B MODE REPLY21AA051AC20 BRNLJ 04THICKNESS AT SHAFT CONNECTING END,BODY BODY THICKNESS AT SHAFT CONNECTING END A MEASUREMENT OF THE THICKNESS OF THE BODY OF AN ITEM AT THE SHAFT CONNECTING END. 2D AND 1B MODE REPLY21AA051AC20 BRNMJ 04DIAMETER,END,CAM CAM END DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BRNNJ 04LENGTH,END,CAM CAM END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BRNPJ 04HEIGHT,CROWN CROWN HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BRNQJ 04HEIGHT,END,CAM CAM END HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BRNRJ 04DISTANCE FROM BOSS FACE TO CAM END DISTANCE FROM BOSS FACE TO CAM END NONE. 2D AND 1B MODE REPLY21AA051AC20 BRNSJ /D/ 04WIDTH,END,CAM CAM END WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BRNTJ /D/ 04RADIUS,END,CAM CAM END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BRNWJ 04DIAMETER,HOLE,BODY BODY HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BRNXJ 04DISTANCE FROM BODY HOLE CENTER TO CAM END DISTANCE FROM BODY HOLE CENTER TO CAM END NONE. 2D AND 1B MODE REPLY21AA051AC20 BRNYJ /D/ 04RADIUS,SPHERICAL,PUSH ROD END PUSH ROD END SPHERICAL RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BRNZJ 04DIAMETER,SPHERICAL,PUSH ROD END PUSH ROD END SPHERICAL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPBJ 04RADIUS,SPHERICAL,CUP CUP SPHERICAL RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPCJ 04DIAMETER,SPHERICAL,CUP CUP SPHERICAL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPDJ 04DEPTH,CUP CUP DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF A CUP,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BRPFJ 04WIDTH,SLOT,FORK FORK SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPGJ 04DIAMETER,HOLE,FORK FORK HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPHJ 04DIAMETER,GROOVE,BODY BODY GROOVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPJJ 04DISTANCE FROM BODY GROOVE CENTER TO CAM END DISTANCE FROM BODY GROOVE CENTER TO CAM END NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPKJ 04DIAMETER,GROOVE,CUP END CUP END GROOVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPLJ 04WIDTH,GROOVE,CUP END CUP END GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPMJ 04DISTANCE FROM CUP END GROOVE CENTER TO CUP END DISTANCE FROM CUP END GROOVE CENTER TO CUP END NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPNJ 04RADIUS,RIDGE,FIRST FIRST RIDGE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPPJ 04RADIUS,RIDGE,SECOND SECOND RIDGE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPQJ 04RADIUS,RIDGE,THIRD THIRD RIDGE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPRJ 04DISTANCE BETWEEN FIRST AND SECOND RIDGE CENTERS DISTANCE BETWEEN FIRST AND SECOND RIDGE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPSJ 04DISTANCE BETWEEN FIRST AND SECOND GROOVE CENTERS DISTANCE BETWEEN FIRST AND SECOND GROOVE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPTJ 04DISTANCE BETWEEN SECOND AND THIRD RIDGE CENTERS DISTANCE BETWEEN SECOND AND THIRD RIDGE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPWJ 04DISTANCE BETWEEN SECOND AND THIRD GROOVE CENTERS DISTANCE BETWEEN SECOND AND THIRD GROOVE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPXJ 04DISTANCE FROM BOTTOM TO FIRST RIDGE CENTER DISTANCE FROM BOTTOM TO FIRST RIDGE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPYJ 04DISTANCE FROM BOTTOM TO FIRST GROOVE CENTER DISTANCE FROM BOTTOM TO FIRST GROOVE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 BRPZJ 04WIDTH,RIDGE,FIRST FIRST RIDGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BRQBJ 04WIDTH,RIDGE,SECOND SECOND RIDGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BRQCJ 04WIDTH,RIDGE,THIRD THIRD RIDGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BRQDJ 04HEIGHT TO SHOULDER HEIGHT TO SHOULDER NONE. 2D AND 1B MODE REPLY21AA051AC20 BRQFJ /D/ 04DIAMETER AT GROOVE BOTTOM DIAMETER AT GROOVE BOTTOM NONE. 2D AND 1B MODE REPLY21AA051AC20 BRQGJ /D/ 04DISTANCE FROM BOTTOM TO RADIUS AT INSIDE DIAMETER DISTANCE FROM BOTTOM TO RADIUS AT INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BRQHB 04ANGLE IN DEG,INCLUDED,INSIDE INSIDE INCLUDED ANGLE IN DEG NONE. 1B MODE REPLY 0 BRQJB 04ANGLE IN DEG,INCLUDED,OUTSIDE OUTSIDE INCLUDED ANGLE IN DEG NONE. 1B MODE REPLY 0 BRQKJ 04RADIUS AT TOP OUTSIDE DIAMETER RADIUS AT TOP OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BRQLJ 04LENGTH TO SHOULDER LENGTH TO SHOULDER NONE. 2D AND 1B MODE REPLY21AA051AC20 BRQMJ 04LENGTH FROM AA END TO LARGEST DIAMETER FACE LENGTH FROM AA END TO LARGEST DIAMETER FACE NONE. 2D AND 1B MODE REPLY21AA051AC20 BRQND 19MEDIA DETECTED MEDIA DETECTED AN INDICATION OF THE MEDIA DETECTED BY THE ITEM. SELECT REPLY CODE 10AB75 BRQPD /D/ 14SHAPE,BOTTOM,TUBE TUBE BOTTOM SHAPE THE PHYSICAL CONFIGURATION OF THE BOTTOM OF THE TUBE(S). SELECT REPLY CODE 10AD07 BRQQD /D/ 09MATERIAL,STAND STAND MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE STAND IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BRQRD /D/ 07SET,WEIGHT WEIGHT SET AN INDICATION OF WHETHER OR NOT A WEIGHT SET IS INLCUDED. SELECT REPLY CODE 10AA49 BRQSJ /D/T10SIZE RANGE,WEIGHT WEIGHT SIZE RANGE DESIGNATES THE SIZE RANGE OF THE WEIGHTS. 1D AND 1F MODE REPLY12AG67 BRQTD 02DESIGN,SYSTEM,LEVER LEVER SYSTEM DESIGN THE DESIGN OF THE LEVER SYSTEM. SELECT REPLY CODE 10AK54 BRQWD /D/ 09MATERIAL,PAN PAN MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PAN IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BRQXD 19POSITION,MOUNTING,PAN PAN MOUNTING POSITION THE INSTALLED POSITION FOR WHICH THE PAN IS DESIGNED. SELECT REPLY CODE 10AM84 BRQYD /D/ 07WEIGHT WEIGHT AN INDICATION OF WHETHER OR NOT A WEIGHT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BRQZD /D/ 07PLUMMET,THERMOMETER,GLASS GLASS THERMOMETER PLUMMET AN INDICATION OF WHETHER OR NOT A GLASS THERMOMETER PLUMMET IS INCLUDED. SELECT REPLY CODE 10AA49 BRRBD 08LOCATION,BEAM,WEIGHT WEIGHT BEAM LOCATION INDICATES THE LOCATION OF THE WEIGHT BEAM. SELECT REPLY CODE 10AJ91 BRRCD /D/ 07PROVISION,BASE,ROD MOUNTING ROD MOUNTING BASE PROVISION AN INDICATION OF WHETHER OR NOT A ROD MOUNTING BASE PROVISION(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BRRDD /D/ 07ACCOMMODATION,HOOK,SPECIFIC GRAVITY WEIGHING SPECIFIC GRAVITY WEIGHING HOOK ACCOMMODATION AN INDICATION OF WHETHER OR NOT A HOOK ACCOMMODATION FOR SPECIFIC GRAVITY WEIGHING IS INCLUDED. SELECT REPLY CODE 10AA49 BRRFD 19FORM,CONTENT,UNIT PACKAGE UNIT PACKAGE CONTENT FORM AN INDICATION OF THE PREPARED STATE OF THE PACKAGED ITEM/S/. SELECT REPLY CODE 10AK54 BRRGD /D/ 07HANDLE,PROBE PROBE HANDLE AN INDICATION OF WHETHER OR NOT A PROBE HANDLE IS INCLUDED. SELECT REPLY CODE 10AA49 BRRHA 12QUANTITY,YOKE,MAGNET MAGNET YOKE QUANTITY THE NUMBER OF MAGNET YOKES PROVIDED. 1A MODE REPLY 0 BRRJJ T10RANGE ACCOMMODATED,GAP,MAGNET MAGNET GAP RANGE ACCOMMODATED A MEASUREMENT OF THE MINIMUM AND MAXIMUM MAGNET GAPS THE ITEM WILL ACCOMMODATE. 1D AND 1F MODE REPLY11AA05 BRRKJ T04DIAMETER RANGE ACCOMMODATED,MAGNET MAGNET DIAMETER RANGE ACCOMMODATED A MEASUREMENT OF THE MINIMUM AND MAXIMUM MAGNET DIAMETERS THE ITEM WILL ACCOMMODATE. 1D AND 1F MODE REPLY11AA05 BRRLD /D/ 09MATERIAL,TUBING,HYDROMETER HYDROMETER TUBING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HYDROMETER TUBING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BRRMD /D/ 09MATERIAL,BALLAST,HYDROMETER HYDROMETER BALLAST MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HYDROMETER BALLAST IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BRRNF T10RANGE,SCALE,HYDROMETER HYDROMETER SCALE RANGE AN INDICATION OF THE MINIMUM AND MAXIMUM LIMITS OF THE HYDROMETER SCALE. 1F MODE REPLY 0 BRRPD 18TYPE,LUMEN,CYLINDER CYLINDER LUMEN TYPE INDICATES THE TYPE OF CYLINDER LUMEN. SELECT REPLY CODE 10AA78 BRRQD /D/ 07GRADUATION,CYLINDER CYLINDER GRADUATION AN INDICATION OF WHETHER OR NOT A CYLINDER(S) GRADUATION IS INCLUDED. SELECT REPLY CODE 10AA49 BRRRD /D/ 07LIP,POURING,CYLINDER CYLINDER POURING LIP AN INDICATION OF WHETHER OR NOT A CYLINDER POURING LIP IS INCLUDED. SELECT REPLY CODE 10AA49 BRRSD /D/ 07TRANSFORMER,LAMP LAMP TRANSFORMER AN INDICATION OF WHETHER OR NOT A TRANSFORMER IS INCLUDED WITH THE LAMP. SELECT REPLY CODE 10AA49 BRRTD /D/ 07SCALE,CONVERSION,TEMP TEMP CONVERSION SCALE AN INDICATION OF WHETHER OR NOT A TEMPERATURE CONVERSION SCALE IS INCLUDED. SELECT REPLY CODE 10AA49 BRRWD /D/ 09MATERIAL,WIRE,TORSION TORSION WIRE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TORSION WIRE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BRRXD /D/ 09MATERIAL,RING RING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE RING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BRRYJ 10CIRCUMFERENCE,RING RING CIRCUMFERENCE A MEASUREMENT OF THE EXTERNAL BOUNDARY OR SURFACE OF THE RING. 1D AND 1B MODE REPLY11AA05 BRRZD /D/ 07TARPAULIN TARPAULIN AN INDICATION OF WHETHER OR NOT A TARPAULIN IS INCLUDED. SELECT REPLY CODE 10AA49 BRSBD /D/ 07BOWS,TOP TOP BOWS AN INDICATION OF WHETHER OR NOT TOP BOWS ARE INCLUDED. SELECT REPLY CODE 10AA49 BRSCJ /D/ 04DISTANCE FROM FLOOR TO TOP BOW,INSIDE INSIDE DISTANCE FROM FLOOR TO TOP BOW THE INSIDE DISTANCE FROM THE FLOOR TO THE TOP BOW. 2D AND 1B MODE REPLY21AA051AC20 BRSDD /D/ 07TAILGATE TAILGATE AN INDICATION OF WHETHER OR NOT A TAILGATE IS INCLUDED. SELECT REPLY CODE 10AA49 BRSFD /D/ 07OPENING,CHUTE CHUTE OPENING AN INDICATION OF WHETHER OR NOT A CHUTE OPENING IS INCLUDED. SELECT REPLY CODE 10AA49 BRSGD /D/ 07PARTITION,BODY BODY PARTITION AN INDICATION OF WHETHER OR NOT A BODY PARTITION(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BRSHD /D/ 07SEAT,TROOP TROOP SEAT AN INDICATION OF WHETHER OR NOT A TROOP SEAT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BRSJJ /D/ 04SIZE ACCOMMODATED,TIRE,MAXIMUM MAXIMUM TIRE SIZE ACCOMMODATED DESIGNATES THE MAXIMUM TIRE SIZE THAT THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BRSKD /D/ 18TYPE FOR WHICH DESIGNED,TESTING TESTING TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF TESTING FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BRSLD 19DEVICE,CONTROL,INDICATOR OPERATION INDICATOR OPERATION CONTROL DEVICE THE CONTROL DEVICE THAT ACTUATES THE OPERATION OF THE INDICATOR. SELECT REPLY CODE 10AK24 BRSMJ T10RANGE,CALIBRATION CALIBRATION RANGE THE MINIMUM AND MAXIMUM CALIBRATED RANGE OF THE ITEM. 1D AND 1F MODE REPLY12AG67 BRSNG /D/ 10GRADUATED DIVISION PER RANGE,SMALLEST SMALLEST GRADUATED DIVISION PER RANGE THE SMALLEST GRADUATED DIVISION MARKINGS WITHIN A GIVEN RANGE. FULL TEXT WRITE-IN 0 BRSPJ /D/A08LOCATION AND QUANTITY,SURFACE,CALIBRATED CALIBRATED SURFACE LOCATION AND QUANTITY INDICATES THE LOCATION AND NUMBER OF CALIBRATED SURFACES. 1D AND 1A MODE REPLY13AJ91 BRSQD 18TYPE,CHUCK CHUCK TYPE INDICATES THE TYPE OF CHUCK FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AK54 BRSRB 04ANGLE IN DEG,MOUNTING,FOOT CHUCK FOOT CHUCK MOUNTING ANGLE IN DEG THE MOUNTING ANGLE OF THE FOOT CHUCK,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BRSSD /D/ 07CLIP,HOLDING,CHUCK VALVE CHUCK VALVE HOLDING CLIP AN INDICATION OF WHETHER OR NOT A CHUCK VALVE HOLDING CLIP IS INCLUDED. SELECT REPLY CODE 10AA49 BRSTD /D/ 07EXTENSION EXTENSION AN INDICATION OF WHETHER OR NOT AN EXTENSION IS INCLUDED. SELECT REPLY CODE 10AA49 BRSWD /D/ 07POSITION,DEFLATING DEFLATING POSITION AN INDICATION OF WHETHER OR NOT A DEFLATING POSITION IS INCLUDED. SELECT REPLY CODE 10AA49 BRSXD /D/ 07COCK,DEFLATING DEFLATING COCK AN INDICATION OF WHETHER OR NOT A DEFLATING COCK IS INCLUDED. SELECT REPLY CODE 10AA49 BRSYD /D/ 07DUCT,OIL OIL DUCT AN INDICATION OF WHETHER OR NOT AN OIL DUCT IS INCLUDED. SELECT REPLY CODE 10AA49 BRSZD /D/ 07FEATURE,QUICK CONNECTION TO INFLATING AIR CHUCK,HOSE COUPLER HOSE COUPLER QUICK CONNECTION TO INFLATING AIR CHUCK FEATURE AN INDICATION OF WHETHER OR NOT A HOSE COUPLER QUICK CONNECTION TO INFLATING AIR CHUCK FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BRTBD 18TYPE,COUPLER,QUICK CONNECTION QUICK CONNECTION COUPLER TYPE INDICATES THE TYPE OF QUICK CONNECTION COUPLER PROVIDED. SELECT REPLY CODE 10AH98 BRTCD /D/ 07HOSE,SAFETY,LONG HIGH PRESSURE LONG HIGH PRESSURE SAFETY HOSE AN INDICATION OF WHETHER OR NOT A LONG HIGH PRESSURE SAFETY HOSE IS INCLUDED. SELECT REPLY CODE 10AA49 BRTDG /D/ 04SIZE ACCOMMODATED,TIRE,AUTOMOTIVE TYPE,MINIMUM MINIMUM AUTOMOTIVE TYPE TIRE SIZE ACCOMMODATED DESIGNATES THE MINIMUM AUTOMOTIVE TYPE TIRE SIZE THE ITEM WILL ACCOMMODATE. FULL TEXT WRITE-IN 0 BRTFG /D/ 04SIZE ACCOMMODATED,TIRE,AUTOMOTIVE TYPE,MAXIMUM MAXIMUM AUTOMOTIVE TYPE TIRE SIZE ACCOMMODATED DESIGNATES THE MAXIMUM AUTOMOTIVE TYPE TIRE SIZE THE ITEM WILL ACCOMMODATE. FULL TEXT WRITE-IN 0 BRTGG 04SIZE ACCOMMODATED,TIRE,AIRPLANE TYPE AIRPLANE TYPE TIRE SIZE ACCOMMODATED DESIGNATES THE AIRPLANE TYPE TIRE SIZE THE ITEM WILL ACCOMMODATE. FULL TEXT WRITE-IN 0 BRTHD 18TYPE,DRIVE,HYDRAULIC UNIT HYDRAULIC UNIT DRIVE TYPE INDICATES THE TYPE OF HYDRAULIC DRIVE UNIT PROVIDED. SELECT REPLY CODE 10AG25 BRTJJ 10PRESSURE,AIR,OPERATING OPERATING AIR PRESSURE THE AMOUNT OF AIR PRESSURE REQUIRED TO OPERATE THE ITEM. 1D AND 1B MODE REPLY12AG67 BRTKD 11METHOD,SUPPLY,WORKING MECHANISM PRESSURE WORKING MECHANISM PRESSURE SUPPLY METHOD THE MEANS OF SUPPLYING PRESSURE TO THE WORKING MECHANISM. SELECT REPLY CODE 10AC58 BRTLJ 10PRESSURE,HYDRAULIC,DEVELOPED DEVELOPED HYDRAULIC PRESSURE THE AMOUNT OF PRESSURE DEVELOPED BY HYDRAULIC FORCE. 1D AND 1B MODE REPLY12AG67 BRTMJ 04WIDTH,MAXIMUM,SPREAD SPREAD MAXIMUM WIDTH THE MAXIMUM WIDTH OF THE SPREAD OF THE ITEM. 1D AND 1B MODE REPLY11AA05 BRTND 02DESIGN,SPREAD SPREAD DESIGN THE DESIGN OF SPREAD THE ITEM CAN PRODUCE. SELECT REPLY CODE 10AK54 BRTPJ T04DIAMETER RANGE ACCOMMODATED,BEAD,TIRE TIRE BEAD DIAMETER RANGE ACCOMMODATED THE MINIMUM AND MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TIRE BEAD THAT THE ITEM WILL ACCOMMODATE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1F MODE REPLY11AA05 BRTQJ T04SIZE RANGE ACCOMMODATED,CROSS-SECTIONAL,TIRE TIRE CROSS-SECTIONAL SIZE RANGE ACCOMMODATED DESIGNATES THE MINIMUM AND MAXIMUM CROSS-SECTIONAL SIZES OF THE TIRE THAT THE ITEM WILL ACCOMMODATE. 1D AND 1F MODE REPLY11AA05 BRTRA 12QUANTITY,ARM,SPREADER SPREADER ARM QUANTITY THE NUMBER OF SPREADER ARMS PROVIDED. 1A MODE REPLY 0 BRTSD /D/ 18TYPE,ARM,SPREADER SPREADER ARM TYPE INDICATES THE TYPE OF SPREADER ARM(S) PROVIDED. SELECT REPLY CODE 10AK54 BRTTD /D/ 18TYPE,KIT,CONVERSION,MOUNTING MOUNTING CONVERSION KIT TYPE INDICATES THE TYPE OF MOUNTING CONVERSION KIT FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AK54 BRTWD 11METHOD,ACTUATION,REEL REEL ACTUATION METHOD THE MEANS BY WHICH THE REEL IS ACTUATED. SELECT REPLY CODE 10AC58 BRTXJ 04LENGTH,OVERALL,DELIVERY HOSE DELIVERY HOSE OVERALL LENGTH THE DIMENSIONS MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE DELIVERY HOSE. 2D AND 1B MODE REPLY21AA051AC20 BRTYD 18TYPE,FITTING,SERVICE END SERVICE END FITTING TYPE INDICATES THE TYPE OF FITTING USED ON THE SERVICE END OF THE ITEM. SELECT REPLY CODE 10AK54 BRTZG 13THREAD CHARACTERISTICS,INLET,REEL REEL INLET THREAD CHARACTERISTICS DESIGNATES THE REEL INLET THREAD CHARACTERISTICS. FULL TEXT WRITE-IN 0 BRWBG 13THREAD CHARACTERISTICS,OUTLET,REEL REEL OUTLET THREAD CHARACTERISTICS DESIGNATES THE REEL OUTLET THREAD CHARACTERISTICS. FULL TEXT WRITE-IN 0 BRWCJ 10READING,MAXIMUM,PRESSURE GAGE PRESSURE GAGE MAXIMUM READING THE MAXIMUM PRESSURE READING OF THE GAGE. 1D AND 1B MODE REPLY12AG67 BRWDG /D/ 19CHARACTERISTICS,HARDWARE,FURNISHED FURNISHED HARDWARE CHARACTERISTICS THE CHARACTERISTICS OF FURNISHED HARDWARE. FULL TEXT WRITE-IN 0 BRWFG /D/ 19CODE AND SIZE/TYPE FOR WHICH DESIGNED,MANUFACTURER,NOZZLE NOZZLE MANUFACTURER CODE AND SIZE/TYPE FOR WHICH DESIGNED THE FEDERAL SUPPLY CODE FOR MANUFACTURERS AND THE SIZE AND/OR TYPE OF THE NOZZLE FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 BRWGJ 04HEIGHT,LIFT,HYDRAULIC HYDRAULIC LIFT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE HYDRAULIC LIFT,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BRWHJ 04HEIGHT,MAXIMUM,FRAME FRAME MAXIMUM HEIGHT THE MAXIMUM MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE FRAME,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BRWJJ 04HEIGHT,EXTENSION,SCREW SCREW EXTENSION HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE SCREW EXTENSION,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BRWKD /D/ 07EXTENSION,LEG LEG EXTENSION AN INDICATION OF WHETHER OR NOT A LEG EXTENSION(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BRWLJ 04HEIGHT,EXTENDED,MAXIMUM MAXIMUM EXTENDED HEIGHT THE MAXIMUM MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE ITEM WHEN EXTENDED,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BRWMD /D/ 07FEATURE,SWIVEL,REAR WHEEL REAR WHEEL SWIVEL FEATURE AN INDICATION OF WHETHER OR NOT A REAR WHEEL SWIVEL FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BRWND 18TYPE,CAP CAP TYPE INDICATES THE TYPE OF CAP FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AK54 BRWPD 07REMOVABILITY,PUMP PUMP REMOVABILITY AN INDICATION OF WHETHER OR NOT THE PUMP IS REMOVABLE. SELECT REPLY CODE 10AC29 BRWQD 18TYPE,DRIVE,CONCENTRIC CONCENTRIC DRIVE TYPE INDICATES THE TYPE OF CONCENTRIC DRIVE PROVIDED. SELECT REPLY CODE 10AG25 BRWRD 18TYPE,CURRENT,ELECTRIC MOTOR ELECTRIC MOTOR CURRENT TYPE INDICATES THE TYPE OF CURRENT FOR THE ELECTRIC MOTOR. SELECT REPLY CODE 10AB62 BRWSD /D/ 07ASSEMBLY FOR SHIPBOARD USE,CABLE,SPECIAL SPECIAL CABLE ASSEMBLY FOR SHIPBOARD USE AN INDICATION OF WHETHER OR NOT A SPECIAL CABLE ASSEMBLY FOR SHIPBOARD USE IS INCLUDED. SELECT REPLY CODE 10AA49 BRWTG /D/ 19SPECIFICATION,ASSEMBLY,CABLE CABLE ASSEMBLY SPECIFICATION THE SPECIFICATION USED TO LIMIT AND/OR CONTROL THE CONSTRUCTION OF THE CABLE ASSEMBLY. FULL TEXT WRITE-IN 0 BRWWA /D/ 12QUANTITY,ITEM ITEM QUANTITY THE NUMBER OF ITEMS PROVIDED. 1A MODE REPLY 0 BRWXJ 04SIZE ACCOMMODATED,PLUG,SPARK SPARK PLUG SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE SPARK PLUG THAT AN ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BRWYG 10PRESSURE RATING AND TYPE REQUIRED PRESSURE RATING AND TYPE REQUIRED THE AMOUNT AND TYPE OF PRESSURE REQUIRED FOR OPERATION. FULL TEXT WRITE-IN 0 BRWZJ 04SIZE,NOMINAL,HOSE CONNECTION HOSE CONNECTION NOMINAL SIZE THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL HOSE CONNECTION SIZE. 1D AND 1B MODE REPLY11AA05 BRXBD 11METHOD,INDICATION,SPARK SPARK INDICATION METHOD THE MEANS BY WHICH THE SPARK IS INDICATED. SELECT REPLY CODE 10AF04 BRXCD /D/ 11METHOD,HEATING,MOLD MOLD HEATING METHOD THE MEANS BY WHICH THE MOLD IS HEATED. SELECT REPLY CODE 10AM63 BRXDD /D/ 07GENERATOR,STEAM STEAM GENERATOR AN INDICATION OF WHETHER OR NOT A STEAM GENERATOR IS INCLUDED. SELECT REPLY CODE 10AA49 BRXFB /D/ 10HORSEPOWER RATING,BOILER,RECOMMENDED RECOMMENDED BOILER HORSEPOWER RATING THE RECOMMENDED HORSEPOWER FOR WHICH THE BOILER IS RATED. 1B MODE REPLY 0 BRXGD /D/ 11METHOD,FIRING FIRING METHOD THE MEANS BY WHICH THE ITEM IS FIRED. SELECT REPLY CODE 10AL88 BRXHD /D/ 18TYPE,CURRENT,FIRING FIRING CURRENT TYPE INDICATES THE TYPE OF FIRING CURRENT PROVIDED. SELECT REPLY CODE 10AB62 BRXJB /D/ 10VOLTAGE IN VOLTS,CURRENT,FIRING FIRING CURRENT VOLTAGE IN VOLTS THE FIRING CURRENT VOLTAGE,EXPRESSED IN VOLTS. 1B MODE REPLY 0 BRXKB /D/ 10WATTAGE RATING IN WATTS,CURRENT,FIRING FIRING CURRENT WATTAGE RATING IN WATTS THE FIRING CURRENT WATTAGE FOR WHICH THE ITEM IS RATED,EXPRESSED IN WATTS. 1B MODE REPLY 0 BRXLB /D/ 10FREQUENCY IN HERTZ,CURRENT,FIRING FIRING CURRENT FREQUENCY IN HERTZ THE FIRING CURRENT FREQUENCY OF THE ITEM,EXPRESSED IN HERTZ. 1B MODE REPLY 0 BRXMD /D/ 19PHASE,CURRENT,FIRING FIRING CURRENT PHASE THE NUMBER OF FIRING CURRENT PHASES OF THE ITEM. SELECT REPLY CODE 10AD02 BRXND 11METHOD,TRANSFER,HEAT HEAT TRANSFER METHOD THE MEANS BY WHICH THE HEAT IS TRANSFERRED. SELECT REPLY CODE 10AK43 BRXPD /D/ 11METHOD,OPENING/CLOSING,MOLD MOLD OPENING/CLOSING METHOD THE MEANS BY WHICH THE MOLD IS OPENED AND/OR CLOSED. SELECT REPLY CODE 10AH25 BRXQD /D/ 07CONTROL,THERMOSTAT THERMOSTAT CONTROL AN INDICATION OF WHETHER OR NOT A THERMOSTAT CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 BRXRD /D/ 07BRACKET,MOUNTING,INTEGRAL INTEGRAL MOUNTING BRACKET AN INDICATION OF WHETHER OR NOT AN INTEGRAL MOUNTING BRACKET IS INCLUDED. SELECT REPLY CODE 10AA49 BRXSJ 04LENGTH,RUNWAY RUNWAY LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE RUNWAY,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BRXTJ 04HEIGHT,RUNWAY RUNWAY HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE RUNWAY,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BRXWD /D/ 07BALANCER,WHEEL WHEEL BALANCER AN INDICATION OF WHETHER OR NOT A WHEEL BALANCER IS INCLUDED. SELECT REPLY CODE 10AA49 BRXXD /D/ 07EQUIPMENT,ALIGNMENT,FRONT END FRONT END ALIGNMENT EQUIPMENT AN INDICATION OF WHETHER OR NOT FRONT END ALIGNMENT EQUIPMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BRXYD /D/ 07EQUIPMENT,STRAIGHTENING,AXLE HOUSING AXLE HOUSING STRAIGHTENING EQUIPMENT AN INDICATION OF WHETHER OR NOT AXLE HOUSING STRAIGHTENING EQUIPMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BRXZD /D/ 18TYPE,GAGE GAGE TYPE INDICATES THE TYPE OF GAGE PROVIDED ON THE ITEM. SELECT REPLY CODE 10AJ89 BRYCD 18TYPE FOR WHICH DESIGNED,GAGE,THREAD THREAD GAGE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF THREAD GAGE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AJ89 BRYDJ 13THREAD PITCH THREAD PITCH A MEASUREMENT OF THE DISTANCE FROM ANY POINT ON THE THREAD TO THE CORRESPONDING POINT ON AN ADJACENT THREAD MEASURED PARALLEL TO THE AXIS. 2D AND 1B MODE REPLY21AA051AC20 BRYFJ 13THREAD LEAD THREAD LEAD THE DISTANCE A SCREW THREAD ADVANCES AXIALLY IN ONE TURN. 2D AND 1B MODE REPLY21AA051AC20 BRYGJ 04THREAD STAMPED PITCH DIAMETER THREAD STAMPED PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF THE THREADED PORTION THAT IS STAMPED ON THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BRYHJ 13THREAD DESIGN PITCH DIAMETER THREAD DESIGN PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF A SCREW THREAD DESIGN. 2D AND 1B MODE REPLY21AA051AC20 BRYJJ 04LENGTH,EDGE,FIRST SCRAPING FIRST SCRAPING EDGE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BRYKJ 04LENGTH,EDGE,SECOND SCRAPING SECOND SCRAPING EDGE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BRYLJ 04DISTANCE BETWEEN SCRAPING EDGES DISTANCE BETWEEN SCRAPING EDGES NONE. 2D AND 1B MODE REPLY21AA051AC20 BRYMJ 04LENGTH EXCLUDING TANG LENGTH EXCLUDING TANG NONE. 2D AND 1B MODE REPLY21AA051AC20 BRYND /D/ 07EDGE,CUTTING,CARBIDE TIPPED CARBIDE TIPPED CUTTING EDGE AN INDICATION OF WHETHER OR NOT A CARBIDE TIPPED CUTTING EDGE IS PROVIDED. SELECT REPLY CODE 10AB22 BRYPA 12QUANTITY,EYE EYE QUANTITY THE NUMBER OF EYES PROVIDED. 1A MODE REPLY 0 BRYQD /D/ 07REVERSIBILITY,BLADE BLADE REVERSIBILITY AN INDICATION OF WHETHER OR NOT A BLADE IS REVERSIBLE. SELECT REPLY CODE 10AF62 BRYRL /D/ 16STYLE,STRIPPER STRIPPER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE STRIPPER. 1L MODE REPLY 0 BRYSD /D/ 07RETURN,STOP,AUTOMATIC AUTOMATIC STOP RETURN AN INDICATION OF WHETHER OR NOT AN AUTOMATIC STOP RETURN IS PROVIDED. SELECT REPLY CODE 10AB22 BRYTG 04SIZE ACCOMMODATED,CABLE/WIRE CABLE/WIRE SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE CABLE OR WIRE ACCOMMODATED. FULL TEXT WRITE-IN 0 BRYXL 16STYLE,END,CURVED CURVED END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CURVED END. 1L MODE REPLY 0 BRYYJ 04LENGTH UNDER HANDLE LENGTH UNDER HANDLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BRYZJ 04DISTANCE ACROSS THROAT DISTANCE ACROSS THROAT NONE. 2D AND 1B MODE REPLY21AA051AC20 BRZBD /D/ 07FEATURE,DESIGN,MEAT HANDLING MEAT HANDLING DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A MEAT HANDLING DESIGN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BRZCD /D/ 07FEATURE,DESIGN,CHAIN HANDLING CHAIN HANDLING DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A CHAIN HANDLING DESIGN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BRZDD /D/ 18TYPE,ROPE ROPE TYPE INDICATES THE TYPE OF ROPE PROVIDED. SELECT REPLY CODE 10AK95 BRZFD /D/ 14SHAPE,EYE EYE SHAPE THE PHYSICAL CONFIGURATION OF THE EYE. SELECT REPLY CODE 10AD07 BRZGD 08LOCATION,EYE EYE LOCATION INDICATES THE TYPE OF EYE IN RELATION TO THE ITEM. SELECT REPLY CODE 10AJ91 BRZHD /D/ 03DESIGNATION,NUMBER NUMBER DESIGNATION A NUMBER/S/ BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. SELECT REPLY CODE 10AN13 BRZJD 07REMOVABILITY,DIE DIE REMOVABILITY AN INDICATION OF WHETHER OR NOT A DIE IS REMOVABLE. SELECT REPLY CODE 10AB00 BRZKG /D/ 19LEGEND/SYMBOL,FACE,DIE DIE FACE LEGEND/SYMBOL THE LEGEND AND/OR SYMBOL ENGRAVED ON THE FACE OF THE DIE. FULL TEXT WRITE-IN 0 BRZLJ 04THICKNESS,TIP,CLOSED CLOSED TIP THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BRZMD /D/ 07END,GRIPPING,NONSPARKING NONSPARKING GRIPPING END AN INDICATION OF WHETHER OR NOT A NONSPARKING GRIPPING END IS PROVIDED. SELECT REPLY CODE 10AB22 BRZND /D/ 07END,HANDLE,NONSPARKING NONSPARKING HANDLE END AN INDICATION OF WHETHER OR NOT A NONSPARKING HANDLE END IS PROVIDED. SELECT REPLY CODE 10AB22 BRZPD 19FLEXIBILITY,HANDLE HANDLE FLEXIBILITY AN INDICATION OF THE FLEXIBILITY OF A HANDLE. SELECT REPLY CODE 10AD03 BRZQD 18TYPE,MECHANISM,HANDLE OPERATING HANDLE OPERATING MECHANISM TYPE INDICATES THE TYPE OF OPERATING MECHANISM INCORPORATED IN THE HANDLE. SELECT REPLY CODE 10AJ57 BRZRD 18TYPE,END,DRIVE DRIVE END TYPE INDICATES THE TYPE OF DRIVE END PROVIDED. SELECT REPLY CODE 10AK84 BRZSD /D/ 14SHAPE,END,DRIVE DRIVE END SHAPE THE PHYSICAL CONFIGURATION OF THE DRIVE END. SELECT REPLY CODE 10AD07 BRZTJ 10SPEED IN RPM,NO LOAD NO LOAD SPEED IN RPM THE SPEED AT WHICH AN ITEM CAN BE OPERATED UNDER A NO LOAD CONDITION,EXPRESSED IN REVOLUTIONS PER MINUTE. 1D AND 1B MODE REPLY11AC20 BRZWJ 10SPEED IN RPM,SHAFT SHAFT SPEED IN RPM THE SPEED AT WHICH THE SHAFT ROTATES,EXPRESSED IN REVOLUTIONS PER MINUTE. 1D AND 1B MODE REPLY11AC20 BRZXD 19DRIVE FOR WHICH DESIGNED DRIVE FOR WHICH DESIGNED AN INDICATION OF THE DRIVE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AN40 BRZYD /D/ 07SWITCH,REVERSING REVERSING SWITCH AN INDICATION OF WHETHER OR NOT A REVERSING SWITCH IS INCLUDED. MRC DISCONTINUED AND REPLACED WITH MRC CBBL AND REPLY CODE GSV, REVERSE SWITCH ON 03/28/2024. SELECT REPLY CODE 10AA49 BRZZD 18TYPE,CONNECTOR,PLUG PLUG CONNECTOR TYPE INDICATES THE TYPE OF PLUG CONNECTOR PROVIDED. SELECT REPLY CODE 10AK12 BSBBJ 04DIAMETER ACCOMMODATED,THREAD,MAXIMUM MAXIMUM THREAD DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR A THREADED ITEM,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BSBCA 04SIZE ACCOMMODATED,WOOD SCREW,MAXIMUM MAXIMUM WOOD SCREW SIZE ACCOMMODATED DESIGNATES THE MAXIMUM SIZE OF THE WOOD SCREW THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 BSBDD /D/ 07GRIP,BODY BODY GRIP AN INDICATION OF WHETHER OR NOT A BODY GRIP IS PROVIDED. SELECT REPLY CODE 10AB22 BSBFD /D/ 07SCREW,FEED FEED SCREW AN INDICATION OF WHETHER OR NOT A FEED SCREW IS PROVIDED. SELECT REPLY CODE 10AB22 BSBGD /D/ 07GUARD,WHEEL WHEEL GUARD AN INDICATION OF WHETHER OR NOT A WHEEL GUARD IS PROVIDED. SELECT REPLY CODE 10AB22 BSBHD /D/ 07FEATURE,TINTED TINTED FEATURE AN INDICATION OF WHETHER OR NOT A TINTED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSBJD 18TYPE,READING,SCALE SCALE READING TYPE INDICATES THE TYPE OF READING PROVIDED BY THE SCALE. SELECT REPLY CODE 10AK54 BSBKD /D/ 09MATERIAL,SURFACE,POSTING POSTING SURFACE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE POSTING SURFACE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BSBLD /D/ 09MATERIAL,COVERING,POSTING SURFACE POSTING SURFACE COVERING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE POSTING SURFACE COVERING IS FABRICATED. SELECT REPLY CODE 10AD09 BSBMD /D/ 18TYPE,TOP,ADDITIONAL CABINET ADDITIONAL CABINET TOP TYPE INDICATES THE TYPE OF ADDITIONAL CABINET TOP PROVIDED. SELECT REPLY CODE 10AK54 BSBND /D/ 07HOIST,TAKEOFF,POWER POWER TAKEOFF HOIST AN INDICATION OF WHETHER OR NOT A POWER TAKEOFF HOIST IS INCLUDED. SELECT REPLY CODE 10AA49 BSBPD /D/ 07PROTECTOR,CAB CAB PROTECTOR AN INDICATION OF WHETHER OR NOT A CAB PROTECTOR IS INCLUDED. SELECT REPLY CODE 10AA49 BSBQD /D/ 07LIGHT,REAR REAR LIGHT AN INDICATION OF WHETHER OR NOT A REAR LIGHT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BSBRD /D/ 07HOIST/SUBFRAME,HYDRAULIC HYDRAULIC HOIST/SUBFRAME AN INDICATION OF WHETHER OR NOT A HYDRAULIC HOIST AND/OR SUBFRAME IS INCLUDED. SELECT REPLY CODE 10AA49 BSBSD /D/ 07PROVISION,TIRE,SPARE SPARE TIRE PROVISION AN INDICATION OF WHETHER OR NOT A SPARE TIRE PROVISION/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BSBTD /D/ 09MATERIAL,MEMBER,CROSS CROSS MEMBER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CROSS MEMBER/S/ IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BSBWD /D/ 07STAKES STAKES AN INDICATION OF WHETHER OR NOT STAKES ARE INCLUDED. SELECT REPLY CODE 10AA49 BSBXG 04SIZE,END,MOUNTING MOUNTING END SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE MOUNTING END. FULL TEXT WRITE-IN 0 BSBYD /D/ 07FASTENER,SIDE,INTERLOCKING INTERLOCKING SIDE FASTENER AN INDICATION OF WHETHER OR NOT AN INTERLOCKING SIDE FASTENER(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BSBZD 02DESIGN,END,POCKET POCKET END DESIGN THE DESIGN OF THE POCKET END. SELECT REPLY CODE 10AK54 BSCBD /D/ 07ACCOMMODATION,CROSSPIECE CROSSPIECE ACCOMMODATION AN INDICATION OF WHETHER OR NOT A CROSSPIECE ACCOMMODATION(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BSCCD /D/ 07FITTING,EYE EYE FITTING AN INDICATION OF WHETHER OR NOT AN EYE FITTING(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BSCDD /D/ 07BRACKET,ANGLE ANGLE BRACKET AN INDICATION OF WHETHER OR NOT AN ANGLE BRACKET(S) IS INCLUDED. MRC DISCONTINUED AND REPLACED WITH MRC ABFF AND REPLY CODE AUH, ANGLE BRACKET ON 03/28/2024. SELECT REPLY CODE 10AA49 BSCFD /D/ 07FEATURE,CONSTRUCTION,WELDED WELDED CONSTRUCTION FEATURE AN INDICATION OF WHETHER OR NOT A WELDED CONSTRUCTION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSCGJ 10SIZE,PLATE PLATE SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE PLATE. 2D AND 1B MODE REPLY21AA051AC20 BSCHJ 04DIAMETER,HOLE,KING PIN LOCKING KING PIN LOCKING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE KING PIN LOCKING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BSCJD /D/ 07PIN,KING KING PIN AN INDICATION OF WHETHER OR NOT A KING PIN IS INCLUDED. SELECT REPLY CODE 10AA49 BSCKJ 04DIAMETER,OUTSIDE,LOCKING RECESS LOCKING RECESS OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR LOCKING RECESS,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BSCLD /D/ 07KINGPIN,RETRACTABLE RETRACTABLE KINGPIN AN INDICATION OF WHETHER OR NOT A RETRACTABLE KINGPIN IS INCLUDED. SELECT REPLY CODE 10AA49 BSCMD /D/ 07ATTACHMENT,TRANSMISSION,POWER POWER TRANSMISSION ATTACHMENT AN INDICATION OF WHETHER OR NOT A POWER TRANSMISSION ATTACHMENT/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BSCND /D/ 07FEATURE,ELEVATING ELEVATING FEATURE AN INDICATION OF WHETHER OR NOT AN ELEVATING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSCPD /D/ 07CONNECTION,BRAKE,AUTOMATIC AUTOMATIC BRAKE CONNECTION AN INDICATION OF WHETHER OR NOT AN AUTOMATIC BRAKE CONNECTION IS INCLUDED. SELECT REPLY CODE 10AA49 BSCQD 11METHOD,FABRICATION,PLATE PLATE FABRICATION METHOD THE MEANS USED TO MANUFACTURE THE PLATE. SELECT REPLY CODE 10AA62 BSCRD 18TYPE,ASSEMBLY,MOUNTED MOUNTED ASSEMBLY TYPE INDICATES THE TYPE OF MOUNTED ASSEMBLY FURNISHED. SELECT REPLY CODE 10AG25 BSCSD /D/ 07FEATURE,MOUNT,RUBBER RUBBER MOUNT FEATURE AN INDICATION OF WHETHER OR NOT A RUBBER MOUNT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSCTD /D/ 07PROVISION,MOUNTING,PLATE W/INTEGRAL RAMP PLATE W/INTEGRAL RAMP MOUNTING PROVISION AN INDICATION OF WHETHER OR NOT A MOUNTING PROVISION FOR PLATE WITH INTEGRAL RAMP/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BSCWD /D/ 07PLATE,MOUNTING MOUNTING PLATE AN INDICATION OF WHETHER OR NOT A MOUNTING PLATE IS INCLUDED. SELECT REPLY CODE 10AA49 BSCXD 08LOCATION,CONTROL CONTROL LOCATION INDICATES THE LOCATION OF THE CONTROL ON THE ITEM. SELECT REPLY CODE 10AJ91 BSCYD /D/ 07CONTROL,RELEASE,KINGPIN HAND LEVER KINGPIN HAND LEVER RELEASE CONTROL AN INDICATION OF WHETHER OR NOT A KINGPIN HAND LEVER RELEASE CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 BSCZJ /D/ 04DISTANCE FROM FLANGE CENTER TO FLAT DISTANCE FROM FLANGE CENTER TO FLAT THE DISTANCE FROM THE FLANGE CENTER TO THE FLAT. 2D AND 1B MODE REPLY21AA051AC20 BSDBJ 04LENGTH,OVERALL,FRAME FRAME OVERALL LENGTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FRAME,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BSDCA 12QUANTITY,PANE PANE QUANTITY THE NUMBER OF PANES PROVIDED WITH THE ITEM. 1A MODE REPLY 0 BSDFD /D/ 09MATERIAL,PANE PANE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PANE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BSDGJ 04LENGTH,PANE PANE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE PANE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BSDHJ 04WIDTH,PANE PANE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PANE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BSDJJ 04THICKNESS,PANE PANE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE PANE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BSDKD /D/ 07GLASS,SAFETY SAFETY GLASS AN INDICATION OF WHETHER OR NOT SAFETY GLASS IS INCLUDED. SELECT REPLY CODE 10AA49 BSDLJ T04DIAMETER TOLERANCE,PITCH PITCH DIAMETER TOLERANCE THE RANGE OF VARIATION PERMITTED ON THE PITCH DIAMETER. 1D AND 1F MODE REPLY11AA05 BSDMD /D/ 07THREADS,TAPERED TAPERED THREADS AN INDICATION OF WHETHER OR NOT TAPERED THREADS ARE INCLUDED. SELECT REPLY CODE 10AA49 BSDND /D/ 08LOCATION,DIAMETER,PITCH,PITCH CONE PITCH CONE PITCH DIAMETER LOCATION INDICATES THE LOCATION OF THE PITCH DIAMETER ON THE PITCH CONE. SELECT REPLY CODE 10AJ91 BSDPA /D/ 18TYPE PER MIL-P-7105,DESIGN DESIGN TYPE PER MIL-P-7105 INDICATES THE TYPE OF THE ITEM AS ILLUSTRATED IN MILITARY SPECIFICATION MIL-P-7105. 1A MODE REPLY 0 BSDQD /D/ 07FEATURE,TRUNCATION,THREAD MAJOR DIAMETER THREAD MAJOR DIAMETER TRUNCATION FEATURE AN INDICATION OF WHETHER OR NOT A THREAD MAJOR DIAMETER TRUNCATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSDRJ 04DIAMETER,MAJOR,TRUNCATED TRUNCATED MAJOR DIAMETER THE MAJOR LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TRUNCATED OUTER MOST SURFACE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BSDSD 03DESIGNATION,LENGTH,TRUNCATION TRUNCATION LENGTH DESIGNATION A DESIGNATION INDICATING THE LENGTH OF THE TRUNCATION. SELECT REPLY CODE 10AK85 BSDYJ 04DIAMETER,OUTSIDE,GAGING MEMBER GAGING MEMBER OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GAGING MEMBER,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BSDZJ T04DIAMETER TOLERANCE,OUTSIDE,GAGING MEMBER GAGING MEMBER OUTSIDE DIAMETER TOLERANCE THE RANGE OF VARIATION PERMITTED ON THE GAGING MEMBER OUTSIDE DIAMETER. 1D AND 1F MODE REPLY11AA05 BSFBD /D/ 07FEATURE,GROOVE,AIR AIR GROOVE FEATURE AN INDICATION OF WHETHER OR NOT AN AIR GROOVE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSFCJ T10RANGE,GAGING GAGING RANGE THE GAGING RANGE FOR WHICH THE ITEM IS DESIGNED. 1D AND 1F MODE REPLY11AA05 BSFDJ /D/A19NAME AND STYLE NUMBER,MEMBER,GAGING GAGING MEMBER NAME AND STYLE NUMBER THE NAME OF THE GAGING MEMBER AND ITS STYLE NUMBER. 1D AND 1A MODE REPLY13AK54 BSFFA 12QUANTITY,MEMBER,GAGING GAGING MEMBER QUANTITY THE NUMBER OF GAGING MEMBERS PROVIDED. 1A MODE REPLY 0 BSFGD 18TYPE,ENGAGEMENT ENGAGEMENT TYPE INDICATES THE TYPE OF ENGAGEMENT PROVIDED. SELECT REPLY CODE 10AK54 BSFHD /D/ 09MATERIAL,ANVIL ANVIL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ANVIL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BSFJJ 04HEIGHT,ENGAGEMENT ENGAGEMENT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE ENGAGEMENT,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 BSFKJ T10TOLERANCE,HEIGHT,ENGAGEMENT ENGAGEMENT HEIGHT TOLERANCE THE RANGE OF VARIATON PERMITTED ON THE ENGAGEMENT HEIGHT. 1D AND 1F MODE REPLY11AA05 BSFLJ 04LENGTH,ENGAGEMENT ENGAGEMENT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ENGAGEMENT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BSFMG 08LOCATION,ENGAGEMENT ENGAGEMENT LOCATION INDICATES THE LOCATION OF THE ENGAGEMENT ON THE ITEM. FULL TEXT WRITE-IN 0 BSFNJ 04DIAMETER,INSIDE,GAGING SURFACE GAGING SURFACE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO GAGING SURFACES OF THE ITEM,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BSFPJ T10TOLERANCE,INSIDE DIAMETER,GAGING SURFACE GAGING SURFACE INSIDE DIAMETER TOLERANCE THE RANGE OF VARIATION PERMITTED ON THE INSIDE DIAMETER OF THE GAGING SURFACE. 1D AND 1F MODE REPLY11AA05 BSFQJ 04LENGTH,MEMBER,GAGING GAGING MEMBER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE GAGING MEMBER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BSFRD 19FINISH,SURFACE,WORKING WORKING SURFACE FINISH AN ADDITIONAL FINISHING PROCESS BY WHICH THE WORKING SURFACE/S/ OF AN ITEM IS ALTERED IN RESPECT TO POLISHING,GRINDING,AND THE LIKE. SELECT REPLY CODE 10AA41 BSFSA 12QUANTITY,SURFACE,WORKING WORKING SURFACE QUANTITY THE NUMBER OF WORKING SURFACES PROVIDED. 1A MODE REPLY 0 BSFTD /D/ 07SLOT SLOT AN INDICATION OF WHETHER OR NOT A SLOT(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BSFWJ 04HEIGHT,FACE,ANGLE ANGLE FACE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE ANGLE FACE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BSFXJ 04WIDTH,FACE,ANGLE ANGLE FACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ANGLE FACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BSFYJ 10ACCURACY,FLATNESS,WORKING SURFACE WORKING SURFACE FLATNESS ACCURACY A MEASUREMENT OF THE FLATNESS ACCURACY OF THE WORKING SURFACE. 2D AND 1B MODE REPLY21AA051AC20 BSFZJ 04DIAMETER,BORE,FIELD HUB FIELD HUB BORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FIELD HUB BORE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BSGBJ 04DIAMETER,BORE,ARMATURE HUB ARMATURE HUB BORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ARMATURE HUB BORE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BSGCB 10HORSEPOWER RATING AT 100 RPM,MAXIMUM MAXIMUM HORSEPOWER RATING AT 100 RPM THE MAXIMUM RATED HORSEPOWER OF THE ITEM AT 100 REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 BSGDJ /D/ 10CURRENT REQUIRED,DIRECT DIRECT CURRENT REQUIRED THE AMOUNT OF DIRECT CURRENT REQUIRED FOR THE ITEM. 1D AND 1B MODE REPLY11AC30 BSGFJ /D/ 10AREA,SURFACE,FRICTION FRICTION SURFACE AREA A MEASUREMENT OF THE FRICTION SURFACE AREA OF THE ITEM. 2D AND 1B MODE REPLY22AG671AC20 BSGGD /D/ 07FACILITY,KEYING KEYING FACILITY AN INDICATION OF WHETHER OR NOT A KEYING FACILITY IS INCLUDED. PLEASE USE MRC ABFF FOR NIINS WERE ANSWERD WITH "INCLUDED" IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BSGHA 12QUANTITY,FACILITY,KEYING KEYING FACILITY QUANTITY THE NUMBER OF KEYING FACILITIES PROVIDED. 1A MODE REPLY 0 BSGJB 04SPACING IN DEG,FACILITY,KEYING KEYING FACILITY SPACING IN DEG THE ANGLE AT WHICH THE KEYING FACILITY(IES) IS SPACED,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BSGKD 18TYPE,FACILITY,KEYING KEYING FACILITY TYPE INDICATES THE TYPE OF KEYING FACILITY PROVIDED. SELECT REPLY CODE 10AK54 BSGLD /D/ 17SURFACE TREATMENT,RIM RIM SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE RIM SURFACE. SELECT REPLY CODE 10AD09 BSGMD 01COLOR,FRONT,PLASTIC PLASTIC FRONT COLOR THE HUE OR TINT OF THE PLASTIC FRONT. SELECT REPLY CODE 10AD06 BSGNJ 04WIDTH,BRIDGE,NOSE NOSE BRIDGE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE NOSE BRIDGE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BSGPD /D/ 07SHIELD,NOSE NOSE SHIELD AN INDICATION OF WHETHER OR NOT A NOSE SHIELD IS INCLUDED. SELECT REPLY CODE 10AA49 BSGQD /D/ 09MATERIAL,SHIELD,NOSE NOSE SHIELD MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE NOSE SHIELD IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BSGRD /D/ 07COVER,BRIDGE BRIDGE COVER AN INDICATION OF WHETHER OR NOT A BRIDGE COVER IS INCLUDED. SELECT REPLY CODE 10AA49 BSGSA /D/ 16STYLE DESIGNATOR,SECTION,TEMPLE TEMPLE SECTION STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TEMPLE SECTION. 1A MODE REPLY 0 BSGTD /D/ 09MATERIAL,SECTION,TEMPLE TEMPLE SECTION MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TEMPLE SECTION IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BSGWD /D/ 17SURFACE TREATMENT,SECTION,TEMPLE TEMPLE SECTION SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE TEMPLE SECTION SURFACE. SELECT REPLY CODE 10AD09 BSGXD 19EXTENT,INSULATION,TEMPLE SECTION TEMPLE SECTION INSULATION EXTENT AN INDICATION AS TO WHAT EXTENT THE TEMPLE SECTION IS INSULATED. SELECT REPLY CODE 10AL70 BSGYD /D/ 07CORE,TEMPLE TEMPLE CORE AN INDICATION OF WHETHER OR NOT A TEMPLE CORE IS INCLUDED. SELECT REPLY CODE 10AA49 BSGZD /D/ 07FEATURE,BICOLORED BICOLORED FEATURE AN INDICATION OF WHETHER OR NOT A BICOLORED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSHBB 10PERCENT,PORTION,COLORED COLORED PORTION PERCENT THE PERCENT OF THE ITEM THAT IS COLORED. 1B MODE REPLY 0 BSHCA 19NUMBER,SHADE,NATIONAL BUREAU OF STANDARDS NATIONAL BUREAU OF STANDARDS SHADE NUMBER A SHADE NUMBER ASSIGNED TO THE ITEM BY THE NATIONAL BUREAU OF STANDARDS. 1A MODE REPLY 0 BSHDD /D/ 07LENS,CURVE,DIOPTER DIOPTER CURVE LENS AN INDICATION OF WHETHER OR NOT A DIOPTER CURVE LENS IS INCLUDED. SELECT REPLY CODE 10AA49 BSHFD /D/ 07LENS,SPARE SPARE LENS AN INDICATION OF WHETHER OR NOT SPARE LENS(ES) IS INCLUDED. SELECT REPLY CODE 10AA49 BSHGD /D/ 07SHIELD,SIDE SIDE SHIELD AN INDICATION OF WHETHER OR NOT A SIDE SHIELD(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BSHHD 19TRANSPARENCY,SHIELD SHIELD TRANSPARENCY THE ABILITY OF THE SHIELD TO TRANSMIT LIGHT AND ALLOW VISUAL PERCEPTION. SELECT REPLY CODE 10AF93 BSHJL /D/ 16STYLE DESIGNATOR,FRAME FRAME STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FRAME. 1L MODE REPLY 0 BSHKD /D/ 07FEATURE,VENTILATION,FRAME FRAME VENTILATION FEATURE AN INDICATION OF WHETHER OR NOT A FRAME VENTILATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSHLD /D/ 07CUP,EYE EYE CUP AN INDICATION OF WHETHER OR NOT AN EYE CUP(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BSHMA /D/ 16STYLE DESIGNATOR,CUP,EYE EYE CUP STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE EYE CUP. 1A MODE REPLY 0 BSHPD /D/ 18TYPE,BRIDGE,NOSE NOSE BRIDGE TYPE INDICATES THE TYPE OF NOSE BRIDGE PROVIDED. SELECT REPLY CODE 10AK54 BSHQD /D/ 07DESIGN,USAGE,OVER OTHER SPECTACLES OVER OTHER SPECTACLES USAGE DESIGN AN INDICATION OF WHETHER OR NOT AN OVER OTHER SPECTACLES USAGE DESIGN IS INCLUDED. SELECT REPLY CODE 10AA49 BSHRD /D/ 07BAR,LIFT,DUAL DUAL LIFT BAR AN INDICATION OF WHETHER OR NOT A DUAL LIFT BAR IS INCLUDED. SELECT REPLY CODE 10AA49 BSHSD /D/ 18TYPE,ELEMENT,APERATURE APERATURE ELEMENT TYPE INDICATES THE TYPE OF ELEMENT WITHIN THE APERATURE. SELECT REPLY CODE 10AM07 BSHTA /D/ 12QUANTITY,LENS,INDIVIDUAL APERTURE INDIVIDUAL APERTURE LENS QUANTITY THE NUMBER OF INDIVIDUAL APERTURE LENSES PROVIDED. 1A MODE REPLY 0 BSHWD /D/ 07FEATURE,BICOLORED,FILTER LENS FILTER LENS BICOLORED FEATURE AN INDICATION OF WHETHER OR NOT A FILTER LENS BICOLORED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSHXA /D/ 19NUMBER,SHADE,NATIONAL BUREAU OF STANDARDS,FILTER LENS FILTER LENS NATIONAL BUREAU OF STANDARDS SHADE NUMBER A SHADE NUMBER ASSIGNED TO THE FILTER LENS BY THE NATIONAL BUREAU OF STANDARDS. 1A MODE REPLY 0 BSHYD /D/ 07FEATURE,HARDENED HARDENED FEATURE AN INDICATION OF WHETHER OR NOT A HARDENED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSHZD 03DESIGNATOR,CURVE,DIOPTER DIOPTER CURVE DESIGNATOR A DESIGNATION INDICATING THE POWER OF THE LENS. SELECT REPLY CODE 10AF81 BSJBD /D/ 07CURVE,DIOPTER DIOPTER CURVE AN INDICATION OF WHETHER OR NOT A DIOPTER CURVE IS INCLUDED ON THE ITEM. SELECT REPLY CODE 10AA49 BSJCD /D/ 18TYPE,LENS,SPARE SPARE LENS TYPE INDICATES THE TYPE OF SPARE LENS(ES) PROVIDED. SELECT REPLY CODE 10AM04 BSJDA 12QUANTITY,LENS,SPARE SPARE LENS QUANTITY THE NUMBER OF SPARE LENSES PROVIDED. 1A MODE REPLY 0 BSJFJ /D/ 04DIAMETER,SCREEN,WIRE WIRE SCREEN DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WIRE SCREEN,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BSJGD /D/ 07PAD,FOREHEAD FOREHEAD PAD AN INDICATION OF WHETHER OR NOT A FOREHEAD PAD IS INCLUDED. SELECT REPLY CODE 10AA49 BSJHD 01COLOR,VISOR VISOR COLOR THE HUE OR TINT OF THE VISOR. SELECT REPLY CODE 10AD06 BSJJD 07REPLACEABILITY,VISOR VISOR REPLACEABILITY AN INDICATION OF WHETHER OR NOT THE VISOR IS REPLACEABLE. SELECT REPLY CODE 10AG84 BSJKD /D/ 07FEATURE,TILTABLE,VISOR VISOR TILTABLE FEATURE AN INDICATION OF WHETHER OR NOT A VISOR TILTABLE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSJLD /D/ 07REGULATOR,VOLUME,AIR AIR VOLUME REGULATOR AN INDICATION OF WHETHER OR NOT AN AIR VOLUME REGULATOR IS PROVIDED. SELECT REPLY CODE 10AB22 BSJML 16STYLE,SHANK,ACCOMMODATED TOOL ACCOMMODATED TOOL SHANK STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SHANK THAT THE TOOL WILL ACCOMMODATE. 1L MODE REPLY 0 BSJND 18TYPE,STAND STAND TYPE INDICATES THE TYPE OF STAND PROVIDED. SELECT REPLY CODE 10AK54 BSJPD /D/ 07BREASTPLATE BREASTPLATE AN INDICATION OF WHETHER OR NOT A BREASTPLATE IS PROVIDED. SELECT REPLY CODE 10AB22 BSJQJ 04LENGTH,SHAFT,FLEXIBLE FLEXIBLE SHAFT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A FLEXIBLE SHAFT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BSJRD /D/ 07FEATURE,OPERATION,HIGH SPEED HIGH SPEED OPERATION FEATURE AN INDICATION OF WHETHER OR NOT A HIGH SPEED OPERATION FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BSJSD /D/ 07SPINDLE,EXTENSION EXTENSION SPINDLE AN INDICATION OF WHETHER OR NOT AN EXTENSION SPINDLE IS PROVIDED. SELECT REPLY CODE 10AB22 BSJTD 11METHOD,OPERATION,ELECTRIC POWER ELECTRIC POWER OPERATION METHOD THE MEANS BY WHICH ELECTRICITY IS USED TO POWER THE OPERATING MECHANISM OF THE ITEM. SELECT REPLY CODE 10AC58 BSJWJ 10SIZE,DRILL,MASONRY MASONRY DRILL SIZE DESIGNATES THE MASONRY DRILL SIZE OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BSJXD 18TYPE,IMPACT,RIVETING RIVETING IMPACT TYPE INDICATES THE TYPE OF RIVETING IMPACT PROVIDED. SELECT REPLY CODE 10AJ57 BSJYJ 04DIAMETER ACCOMMODATED,RIVET,COLD ALUMINUM ALLOY COLD ALUMINUM ALLOY RIVET DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR A COLD ALUMINUM ALLOY RIVET,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BSJZJ 04DIAMETER ACCOMMODATED,RIVET,COLD STEEL COLD STEEL RIVET DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR A COLD STEEL RIVET,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BSKBD 10SPEED,HITTING HITTING SPEED AN INDICATION OF THE HITTING SPEED OF THE ITEM. SELECT REPLY CODE 10AG48 BSKCD /D/ 07DEVICE,RETAINING,NAIL DRIVING NAIL DRIVING RETAINING DEVICE AN INDICATION OF WHETHER OR NOT A NAIL DRIVING RETAINING DEVICE IS PROVIDED. SELECT REPLY CODE 10AB22 BSKDJ 04DIAMETER,BORE,PISTON PISTON BORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PISTON BORE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BSKFA 10CAPACITY,CUTTING,MAXIMUM,USS GAGE SHEET STEEL USS GAGE SHEET STEEL MAXIMUM CUTTING CAPACITY THE MAXIMUM THICKNESS GAGE NUMBER OF UNITED STATES STANDARD SHEET STEEL THAT THE ITEM CAN CUT. 1A MODE REPLY 0 BSKGJ 04WIDTH FOR WHICH DESIGNED,JAW JAW WIDTH FOR WHICH DESIGNED A MEASUREMENT OF THE WIDTH OF THE JAW FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 BSKJJ 10LOAD RATING,TEST TEST LOAD RATING AN INDICATION OF THE LOAD RATING FOR WHICH THE ITEM IS TESTED. 1D AND 1B MODE REPLY11AB10 BSKKD 18TYPE,PROTECTION,WELDING WELDING PROTECTION TYPE INDICATES THE TYPE OF PROTECTION PROVIDED FOR WELDING. SELECT REPLY CODE 10AL37 BSKLD /D/ 07PROVISION,ATTACHMENT,GROUND CABLE GROUND CABLE ATTACHMENT PROVISION AN INDICATION OF WHETHER OR NOT A GROUND CABLE ATTACHMENT PROVISION IS PROVIDED. SELECT REPLY CODE 10AB22 BSKMD /D/ 07FEATURE,ADJUSTMENT,QUICK QUICK ADJUSTMENT FEATURE AN INDICATION OF WHETHER OR NOT A QUICK ADJUSTMENT FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BSKNJ 10OPENING,NOMINAL,JAW JAW NOMINAL OPENING THE NOMINAL MEASUREMENT OF THE JAW OPENING OF THE ITEM. 1D AND 1B MODE REPLY11AA05 BSKPJ 04LENGTH,OVERALL,CLOSED CLOSED OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BSKQL 16STYLE DESIGNATOR,CLAMP,PLIERS PLIERS CLAMP STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PLIERS CLAMP. 1L MODE REPLY 0 BSKRJ 04DISTANCE FROM SCREW AXIS TO BAR EDGE DISTANCE FROM SCREW AXIS TO BAR EDGE THE DISTANCE FROM THE AXIS OF THE SCREW TO THE EDGE OF THE BAR. 2D AND 1B MODE REPLY21AA051AC20 BSKSD /D/ 07BRIDLE,CABLE,BODY BODY CABLE BRIDLE AN INDICATION OF WHETHER OR NOT A BODY CABLE BRIDLE IS PROVIDED. SELECT REPLY CODE 10AB22 BSKTD 18TYPE,EYE,PULLING PULLING EYE TYPE INDICATES THE TYPE OF PULLING EYE PROVIDED. SELECT REPLY CODE 10AK95 BSKWD /D/ 09MATERIAL,JAW JAW MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE JAW IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BSKXD 19CONDITION,SURFACE,JAW JAW SURFACE CONDITION THE CONDITION OF THE JAW WITH RESPECT TO THE TEXTURE OF THE SURFACE. SELECT REPLY CODE 10AK39 BSKYD /D/ 07WEDGE,ALTERNATE ALTERNATE WEDGE AN INDICATION OF WHETHER OR NOT AN ALTERNATE WEDGE(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BSKZD /D/ 07BRIDLE,CABLE,WEDGE WEDGE CABLE BRIDLE AN INDICATION OF WHETHER OR NOT A WEDGE CABLE BRIDLE IS PROVIDED. SELECT REPLY CODE 10AB22 BSLBD /D/ 07PULLEY PULLEY AN INDICATION OF WHETHER OR NOT A PULLEY IS PROVIDED. SELECT REPLY CODE 10AB22 BSLCA 12QUANTITY,EYE,PULLING PULLING EYE QUANTITY THE NUMBER OF PULLING EYES PROVIDED. 1A MODE REPLY 0 BSLDD 02DESIGN,EYE,PULLING PULLING EYE DESIGN THE DESIGN OF THE PULLING EYE PROVIDED. SELECT REPLY CODE 10AK54 BSLFL 16STYLE DESIGNATOR,PLIERS PLIERS STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PLIERS. 1L MODE REPLY 0 BSLGB /D/ 04ANGLE IN DEG,JAW JAW ANGLE IN DEG THE ANGLE OF THE JAW,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BSLHJ /D/ 04SIZE ACCOMMODATED,STAPLE,HOG RING HOG RING STAPLE SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE HOG RING STAPLE(S) THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 BSLJB 04ANGLE IN DEG,TIP TIP ANGLE IN DEG THE ANGLE OF THE TIP,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BSLKD /D/ 07HANDLE,INSULATED INSULATED HANDLE AN INDICATION OF WHETHER OR NOT AN INSULATED HANDLE(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BSLLJ /D/ 04DISTANCE FROM STITCH TO FRAME DISTANCE FROM STITCH TO FRAME THE DISTANCE FROM THE STITCH TO THE FRAME OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BSLMA 12QUANTITY,SECTION,FOLDING FOLDING SECTION QUANTITY THE NUMBER OF FOLDING SECTIONS PROVIDED. 1A MODE REPLY 0 BSLND 18TYPE,FOLDER FOLDER TYPE INDICATES THE TYPE OF FOLDER PROVIDED. SELECT REPLY CODE 10AL76 BSLPJ /D/ 04LENGTH,MAXIMUM,SHEET,PARALLEL FOLD PARALLEL FOLD SHEET MAXIMUM LENGTH THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF A SHEET THAT THE ITEM CAN PARALLEL FOLD,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BSLQJ 04WIDTH,MAXIMUM,SHEET,PARALLEL FOLD PARALLEL FOLD SHEET MAXIMUM WIDTH THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A SHEET THAT THE ITEM CAN PARALLEL FOLD,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BSLRA 12QUANTITY,HEAD,STITCHING STITCHING HEAD QUANTITY THE NUMBER OF STITCHING HEADS PROVIDED. 1A MODE REPLY 0 BSLSJ 04THICKNESS,MAXIMUM,STITCHING STITCHING MAXIMUM THICKNESS THE MAXIMUM MEASUREMENT OF THE SMALLEST DIMENSION OF THE STITCHING OF THE ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 BSLTD /D/ 07GAGE,BACK,AUTOMATIC TRIP AUTOMATIC TRIP BACK GAGE AN INDICATION OF WHETHER OR NOT AN AUTOMATIC TRIP BACK GAGE IS INCLUDED. SELECT REPLY CODE 10AA49 BSLWJ /D/ 04LENGTH,MAXIMUM,SHEET,RIGHT ANGLE FOLD RIGHT ANGLE FOLD SHEET MAXIMUM LENGTH THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF A SHEET THAT THE ITEM CAN RIGHT ANGLE FOLD,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BSLXJ 04WIDTH,MAXIMUM,SHEET,RIGHT ANGLE FOLD RIGHT ANGLE FOLD SHEET MAXIMUM WIDTH THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A SHEET THAT THE ITEM CAN RIGHT ANGLE FOLD,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BSLYD /D/ 07ATTACHMENT,PASTING PASTING ATTACHMENT AN INDICATION OF WHETHER OR NOT A PASTING ATTACHMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BSLZD /D/ 07ATTACHMENT,PERFORATING PERFORATING ATTACHMENT AN INDICATION OF WHETHER OR NOT A PERFORATING ATTACHMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BSMBD /D/ 07ATTACHMENT,SLITTING SLITTING ATTACHMENT AN INDICATION OF WHETHER OR NOT A SLITTING ATTACHMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BSMCD /D/ 07ATTACHMENT,SCORING SCORING ATTACHMENT AN INDICATION OF WHETHER OR NOT A SCORING ATTACHMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BSMDG 04SIZE,COPY,IMAGE IMAGE COPY SIZE DESIGNATES THE SIZE OF THE TOTAL SURFACE OF THE IMAGE COPY. FULL TEXT WRITE-IN 0 BSMFD /D/ 11METHOD,STOCKING STOCKING METHOD THE MEANS BY WHICH THE ITEM IS STOCKED. SELECT REPLY CODE 10AB47 BSMGG /D/ 12QUANTITY BY SIZE PER FONT,PIECE PIECE QUANTITY BY SIZE PER FONT THE NUMBER OF PIECES OF A SPECIFIED SIZE PER FONT. FULL TEXT WRITE-IN 0 BSMHF /D/T04SIZE RANGE IN EMS,STOCK STOCK SIZE RANGE IN EMS DESIGNATES THE SIZE RANGE OF THE STOCK,EXPRESSED IN EMS. 1F MODE REPLY 0 BSMJD 08LOCATION,PERFORATION PERFORATION LOCATION INDICATES THE LOCATION OF THE PERFORATION(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 BSMKG /D/ 11METHOD,ATTACHMENT ATTACHMENT METHOD THE MEANS USED TO ATTACH THE ITEM. FULL TEXT WRITE-IN 0 BSMLD 18TYPE,END,ATTACHING ATTACHING END TYPE INDICATES THE TYPE OF END(S) USED TO ATTACH THE ITEM. SELECT REPLY CODE 10AK84 BSMMD 08LOCATION,COATING,SENSITIZED SENSITIZED COATING LOCATION INDICATES THE LOCATION OF THE SENSITIZED COATING ON THE ITEM. SELECT REPLY CODE 10AJ91 BSMND 08LOCATION,SURFACE,PRINTING PRINTING SURFACE LOCATION INDICATES THE LOCATION OF THE PRINTING SURFACE ON THE ITEM. SELECT REPLY CODE 10AJ91 BSMPA 12QUANTITY,LIFE RATING IN COPY,AVERAGE,PRINTING SURFACE PRINTING SURFACE AVERAGE LIFE RATING IN COPY QUANTITY THE NUMERIC VALUE INDICATING THE AVERAGE LIFE EXPECTANCY FOR WHICH THE PRINTING SURFACE IS RATED,EXPRESSED IN THE NUMBER OF COPIES. 1A MODE REPLY 0 BSMQD /D/ 07INDICIA,MARGINAL MARGINAL INDICIA AN INDICATION OF WHETHER OR NOT A MARGINAL INDICIA IS PROVIDED. SELECT REPLY CODE 10AB22 BSMRD 18TYPE FOR WHICH DESIGNED,IMAGE IMAGE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF IMAGE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AG50 BSMSD 11METHOD,TRANSFER TRANSFER METHOD THE MEANS BY WHICH THE TRANSFER IS ACCOMPLISHED. SELECT REPLY CODE 10AK43 BSMTJ 04LENGTH,UNIT,SUBSTANCE SUBSTANCE UNIT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SUBSTANCE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BSMWJ 04WIDTH,UNIT,SUBSTANCE SUBSTANCE UNIT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SUBSTANCE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BSMXD 18TYPE,BACKGROUND BACKGROUND TYPE INDICATES THE TYPE OF BACKGROUND PROVIDED. SELECT REPLY CODE 10AK54 BSMZJ 04WIDTH,EXTENDED EXTENDED WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM WHEN IT IS IN AN EXTENDED POSITION,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BSNBJ 04WIDTH,RETRACTED RETRACTED WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM WHEN IT IS IN A RETRACTED POSITION,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BSNCD 19TRANSPARENCY,GLASS,WORKING SURFACE WORKING SURFACE GLASS TRANSPARENCY AN INDICATION OF THE TRANSPARENCY OF THE GLASS WORKING SURFACE. SELECT REPLY CODE 10AF93 BSNDJ 04LENGTH,SURFACE,WORKING WORKING SURFACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SURFACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BSNFJ 04WIDTH,SURFACE,WORKING WORKING SURFACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A WORKING SURFACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BSNGD /D/ 09MATERIAL,COMPARTMENT COMPARTMENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE COMPARTMENT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BSNHD /D/ 07EDGE,STRAIGHT,MOVABLE HORIZONTAL MOVABLE HORIZONTAL STRAIGHT EDGE AN INDICATION OF WHETHER OR NOT A MOVABLE HORIZONTAL STRAIGHT EDGE IS INCLUDED. SELECT REPLY CODE 10AA49 BSNJD /D/ 07EDGE,STRAIGHT,MOVABLE VERTICAL MOVABLE VERTICAL STRAIGHT EDGE AN INDICATION OF WHETHER OR NOT A MOVABLE VERTICAL STRAIGHT EDGE IS INCLUDED. SELECT REPLY CODE 10AA49 BSNKD 18TYPE,BLANKET BLANKET TYPE INDICATES THE TYPE OF BLANKET PROVIDED. SELECT REPLY CODE 10AK84 BSNLJ 04WIDTH,FACILITY,KEYING KEYING FACILITY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE KEYING FACILITY,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BSNMJ 04DISTANCE FROM BORE CENTER TO KEYING FACILITY DISTANCE FROM BORE CENTER TO KEYING FACILITY THE DISTANCE FROM THE CENTER OF THE BORE TO THE KEYING FACILITY. 2D AND 1B MODE REPLY21AA051AC20 BSNND /D/ 07FEATURE,COUNTERBORE,BORE BORE COUNTERBORE FEATURE AN INDICATION OF WHETHER OR NOT A BORE COUNTERBORE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSNPD 11METHOD,SECURING SECURING METHOD THE MEANS BY WHICH THE ITEM IS SECURED. SELECT REPLY CODE 10AM39 BSNQA 12QUANTITY,HOLE,THREADED THREADED HOLE QUANTITY THE NUMBER OF THREADED HOLES PROVIDED. 1A MODE REPLY 0 BSNRG 08LOCATION,HOLE,THREADED THREADED HOLE LOCATION INDICATES THE LOCATION OF A THREADED HOLE ON THE ITEM. FULL TEXT WRITE-IN 0 BSNSA 12QUANTITY,HOLE,UNTHREADED UNTHREADED HOLE QUANTITY THE NUMBER OF UNTHREADED HOLES PROVIDED. 1A MODE REPLY 0 BSNTA /D/ 19NUMBER,TAPER,HOLE HOLE TAPER NUMBER A NUMBER INDICATING THE AMOUNT OF TAPER IN A HOLE. 1A MODE REPLY 0 BSNWG 08LOCATION,HOLE,UNTHREADED UNTHREADED HOLE LOCATION INDICATES THE LOCATION OF AN UNTHREADED HOLE ON THE ITEM. FULL TEXT WRITE-IN 0 BSNXJ /D/ 04DIAMETER,RACE,FORK FORK RACE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FORK RACE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BSNYJ /D/ 04WIDTH,RACE,FORK FORK RACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FORK RACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BSNZG /D/ 08LOCATION,RACE,FORK FORK RACE LOCATION INDICATES THE LOCATION OF A FORK RACE ON THE ITEM. FULL TEXT WRITE-IN 0 BSPBD 19CONFIGURATION,END END CONFIGURATION THE GEOMETRIC CONFIGURATION OF THE END/S/ WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AE88 BSPCG /D/ 19DIMENSIONS,CHAMFER,END END CHAMFER DIMENSIONS THE MEASUREMENT TAKEN TO SPECIFY THE CHAMFER OF THE END ON AN ITEM. FULL TEXT WRITE-IN 0 BSPDD /D/ 07FACING,MATERIAL,FRICTION FRICTION MATERIAL FACING AN INDICATION OF WHETHER OR NOT A FRICTION MATERIAL FACING IS INCLUDED. SELECT REPLY CODE 10AA49 BSPFD 18TYPE,COMPOSITION,ASBESTOS ASBESTOS COMPOSITION TYPE INDICATES THE TYPE OF ASBESTOS COMPOSITION PROVIDED. SELECT REPLY CODE 10AN27 BSPGJ /D/ 04DIAMETER,OUTSIDE,MATERIAL MATERIAL OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MATERIAL,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BSPHJ /D/ 04DIAMETER,INSIDE,MATERIAL MATERIAL INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MATERIAL,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BSPJA /D/ 12QUANTITY PER SIDE,SECTION SECTION QUANTITY PER SIDE THE NUMBER OF SECTIONS ON EACH SIDE OF THE ITEM. 1A MODE REPLY 0 BSPKD /D/ 07GROOVE,FACING,MATERIAL MATERIAL FACING GROOVE AN INDICATION OF WHETHER OR NOT A GROOVE(S) IS PROVIDED IN THE MATERIAL FACING. SELECT REPLY CODE 10AB22 BSPLD /D/ 11METHOD,ATTACHMENT,FACING FACING ATTACHMENT METHOD THE MEANS BY WHICH THE FACING IS ATTACHED. SELECT REPLY CODE 10AB47 BSPMA /D/ 12QUANTITY,SEGMENT,CUSHION CUSHION SEGMENT QUANTITY THE NUMBER OF CUSHION SEGMENTS PROVIDED. 1A MODE REPLY 0 BSPNA /D/ 12QUANTITY,SPRING,DAMPER DAMPER SPRING QUANTITY THE NUMBER OF DAMPER SPRINGS PROVIDED. 1A MODE REPLY 0 BSPPD /D/ 07PROVISION,ENCASEMENT,DAMPER SPRING DAMPER SPRING ENCASEMENT PROVISION AN INDICATION OF WHETHER OR NOT A DAMPER SPRING ENCASEMENT PROVISION IS INCLUDED. SELECT REPLY CODE 10AA49 BSPQA /D/ 12QUANTITY,DEFLECTOR,OIL OIL DEFLECTOR QUANTITY THE NUMBER OF OIL DEFLECTORS PROVIDED. 1A MODE REPLY 0 BSPRJ /D/ 04DIAMETER,OUTSIDE,OIL DEFLECTOR OIL DEFLECTOR OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OIL DEFLECTOR,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BSPSD /D/ 07HUB,INTEGRAL INTEGRAL HUB AN INDICATION OF WHETHER OR NOT AN INTEGRAL HUB IS INCLUDED. SELECT REPLY CODE 10AA49 BSPTJ /D/ 04DISTANCE FROM FLYWHEEL FACE TO REAR OF HUB DISTANCE FROM FLYWHEEL FACE TO REAR OF HUB THE DISTANCE FROM THE FLYWHEEL FACE TO THE REAR OF THE HUB. 2D AND 1B MODE REPLY21AA051AC20 BSPWD /D/ 09MATERIAL,DISK DISK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE DISK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BSPXJ 04DIAMETER,INSIDE,SMALLEST SMALLEST INSIDE DIAMETER THE SMALLEST LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO SURFACES OF A CIRCULAR ITEM,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BSPYJ /D/ 04ANGLE BETWEEN SLOTS IN DEG ANGLE BETWEEN SLOTS IN DEG THE ANGLE BETWEEN THE SLOTS,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 BSPZA /D/ 12QUANTITY,SET,TEETH TEETH SET QUANTITY THE NUMBER OF TEETH SETS PROVIDED. 1A MODE REPLY 0 BSQBA /D/ 12QUANTITY PER SET,TEETH TEETH QUANTITY PER SET THE NUMBER OF TEETH IN EACH SET. 1A MODE REPLY 0 BSQCA 12QUANTITY PER DISK,TEETH TEETH QUANTITY PER DISK THE NUMBER OF TEETH IN EACH DISK. 1A MODE REPLY 0 BSQDJ /D/ 04DIAMETER,PITCH,TEETH TEETH PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF THE TEETH. 2D AND 1B MODE REPLY21AA051AC20 BSQFD /D/ 07HOLE,BOLT BOLT HOLE AN INDICATION OF WHETHER OR NOT A BOLT HOLE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BSQGD 18TYPE,GEAR GEAR TYPE INDICATES THE TYPE OF GEAR PROVIDED. SELECT REPLY CODE 10AH55 BSQHG 10RATIO,TOTAL TOTAL RATIO THE TOTAL RATIO OF THE INPUT REVOLUTIONS TO THE OUTPUT REVOLUTIONS OF THE ITEM. FULL TEXT WRITE-IN 0 BSQJD /D/ 07DESIGN,USAGE,SHIPBOARD SHIPBOARD USAGE DESIGN AN INDICATION OF WHETHER OR NOT A SHIPBOARD USAGE DESIGN IS PROVIDED. SELECT REPLY CODE 10AB22 BSQKD 19SYSTEM,LUBRICATION LUBRICATION SYSTEM THE SYSTEM USED FOR LUBRICATING THE ITEM. SELECT REPLY CODE 10AN42 BSQLD 11METHOD,SUPPORT,VISOR VISOR SUPPORT METHOD THE MEANS PROVIDED TO SUPPORT THE VISOR. SELECT REPLY CODE 10AM39 BSQMD 11METHOD,ATTACHMENT,VISOR SUPPORT VISOR SUPPORT ATTACHMENT METHOD THE MEANS USED TO ATTACH THE VISOR SUPPORT. SELECT REPLY CODE 10AM39 BSQNJ 04LENGTH,VISOR VISOR LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE VISOR,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BSQPJ 04WIDTH,VISOR VISOR WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE VISOR,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BSQQJ 04THICKNESS,VISOR VISOR THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE VISOR,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BSQRA 12QUANTITY,CANISTER CANISTER QUANTITY THE NUMBER OF CANISTERS PROVIDED. 1A MODE REPLY 0 BSQSD /D/ 19PROTECTION FOR WHICH DESIGNED,CANISTER CANISTER PROTECTION FOR WHICH DESIGNED AN INDICATION OF THE PROTECTION FOR WHICH THE CANISTER IS DESIGNED. SELECT REPLY CODE 10AA65 BSQTA 19SYMBOL,MANUFACTURER,CANISTER CANISTER MANUFACTURER SYMBOL THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED SYMBOL OF THE CANISTER MANUFACTURER. 1A MODE REPLY 0 BSQWD /D/ 07FILTER,PARTICULATE,CANISTER CANISTER PARTICULATE FILTER AN INDICATION OF WHETHER OR NOT A CANISTER PARTICULATE FILTER IS INCLUDED. SELECT REPLY CODE 10AA49 BSQXD 11METHOD,ATTACHMENT,CANISTER TO FACEPIECE CANISTER TO FACEPIECE ATTACHMENT METHOD THE MEANS BY WHICH THE CANISTER IS ATTACHED TO THE FACEPIECE. SELECT REPLY CODE 10AM39 BSQYA 12QUANTITY,HOSE HOSE QUANTITY THE NUMBER OF HOSES PROVIDED. 1A MODE REPLY 0 BSQZD 19CODE,COLOR,CANISTER IDENTIFICATION CANISTER IDENTIFICATION COLOR CODE THE APPLICATION OF COLOR OR SERIES OF COLOR FOR THE EXPRESSED PURPOSE OF IDENTIFYING THE SPECIFIC DESIGN AND/OR SYSTEM APPLICATION OF A CANISTER. SELECT REPLY CODE 10AD06 BSRBD /D/ 07TIMER,AUTOMATIC,CANISTER CANISTER AUTOMATIC TIMER AN INDICATION OF WHETHER OR NOT A CANISTER AUTOMATIC TIMER IS INCLUDED. SELECT REPLY CODE 10AA49 BSRCD /D/ 07HARNESS,CARRYING,CANISTER CANISTER CARRYING HARNESS AN INDICATION OF WHETHER OR NOT A CANISTER CARRYING HARNESS IS INCLUDED. SELECT REPLY CODE 10AA49 BSRDD 19POSITION FOR WHICH DESIGNED,CARRYING CARRYING POSITION FOR WHICH DESIGNED THE CARRYING POSITION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AM84 BSRFD 02DESIGN,FACEPIECE FACEPIECE DESIGN THE DESIGN OF THE FACEPIECE PROVIDED. SELECT REPLY CODE 10AK54 BSRGD /D/ 07PROVISION,USAGE,SPECTACLE SPECTACLE USAGE PROVISION AN INDICATION OF WHETHER OR NOT A SPECTACLE USAGE PROVISION IS PROVIDED. SELECT REPLY CODE 10AB22 BSRHD /D/ 09MATERIAL,FACEPIECE FACEPIECE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FACEPIECE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BSRJD /D/ 09MATERIAL,LENS,FACEPIECE FACEPIECE LENS MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FACEPIECE LENS IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BSRKD /D/ 07DIAPHRAGM,SPEAKING,FACEPIECE FACEPIECE SPEAKING DIAPHRAGM AN INDICATION OF WHETHER OR NOT A FACEPIECE SPEAKING DIAPHRAGM IS INCLUDED. SELECT REPLY CODE 10AA49 BSRLD 03DESIGNATION,SIZE,FACEPIECE FACEPIECE SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE FACEPIECE IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. SELECT REPLY CODE 10AF81 BSRMD /D/ 09MATERIAL,HARNESS,HEAD HEAD HARNESS MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HEAD HARNESS IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BSRND /D/ 07LINING,FACE FACE LINING AN INDICATION OF WHETHER OR NOT A FACE LINING IS INCLUDED. SELECT REPLY CODE 10AA49 BSRPD 19FACILITY,CARRYING CARRYING FACILITY AN INDICATION OF THE CARRYING FACILITY PROVIDED. SELECT REPLY CODE 10AC55 BSRQD 18TYPE,POSITION,CARRIER CARRIER POSITION TYPE INDICATES THE TYPE OF CARRIER POSITION PROVIDED. SELECT REPLY CODE 10AK84 BSRRD 19POSITION,WEARING,CARRIER CARRIER WEARING POSITION THE POSITION IN WHICH THE CARRIER IS DESIGNED TO BE WORN. SELECT REPLY CODE 10AM84 BSRSD 19POSITION,WEARING,CARRIER,MASK NOT IN USE MASK NOT IN USE CARRIER WEARING POSITION THE POSITION IN WHICH THE CARRIER IS DESIGNED TO BE WORN WHEN THE MASK IS NOT IN USE. SELECT REPLY CODE 10AM84 BSRTD /D/ 19APPROVAL,BUREAU OF MINES BUREAU OF MINES APPROVAL AN INDICATION OF WHETHER OR NOT A BUREAU OF MINES APPROVAL IS REQUIRED. SELECT REPLY CODE 10AE40 BSRWA /D/ 19SCHEDULE,BUREAU OF MINES BUREAU OF MINES SCHEDULE THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH IDENTIFIES THE BUREAU OF MINES SCHEDULE. 1A MODE REPLY 0 BSRXD 18TYPE,SYSTEM,OXYGEN OXYGEN SYSTEM TYPE INDICATES THE TYPE OF OXYGEN SYSTEM PROVIDED. SELECT REPLY CODE 10AL77 BSRYD /D/ 07FASTENER,HELMET HELMET FASTENER AN INDICATION OF WHETHER OR NOT A HELMET FASTENER(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BSRZJ 04LENGTH,TUBE,INTAKE INTAKE TUBE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE INTAKE TUBE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BSSBD /D/ 07FEATURE,CORRUGATED,INTAKE TUBE INTAKE TUBE CORRUGATED FEATURE AN INDICATION OF WHETHER OR NOT AN INTAKE TUBE CORRUGATED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSSCD /D/ 07MICROPHONE MICROPHONE AN INDICATION OF WHETHER OR NOT A MICROPHONE IS INCLUDED. SELECT REPLY CODE 10AA49 BSSDD /D/ 07POCKET,MICROPHONE MICROPHONE POCKET AN INDICATION OF WHETHER OR NOT A MICROPHONE POCKET IS INCLUDED. SELECT REPLY CODE 10AA49 BSSFD 03DESIGNATION,SIZE,MASK MASK SIZE DESIGNATION THE SIZE DESIGNATION BY WHICH THE MASK IS COMMERCIALLY KNOWN. SELECT REPLY CODE 10AF81 BSSGD 07REPLACEABILITY,FILTER FILTER REPLACEABILITY AN INDICATION OF WHETHER OR NOT THE FILTER IS REPLACEABLE. SELECT REPLY CODE 10AG84 BSSHD /D/ 07FEATURE,COUPLING,QUICK DISCONNECT QUICK DISCONNECT COUPLING FEATURE AN INDICATION OF WHETHER OR NOT A QUICK DISCONNECT COUPLING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSSJD 18TYPE,COVER,FACE FACE COVER TYPE INDICATES THE TYPE OF FACE COVER PROVIDED. SELECT REPLY CODE 10AK54 BSSKD 19SPECIES FOR WHICH DESIGNED,ANIMAL ANIMAL SPECIES FOR WHICH DESIGNED AN INDICATION OF THE SPECIES OF ANIMALS FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AE92 BSSLD /D/ 07PANE,TINTED TINTED PANE AN INDICATION OF WHETHER OR NOT A TINTED PANE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BSSMJ 10CAPACITY,TANK TANK CAPACITY INDICATES THE CAPACITY OF THE TANK. 1D AND 1B MODE REPLY12AG67 BSSNA 12QUANTITY,OPENING,LINE CONNECTION LINE CONNECTION OPENING QUANTITY THE NUMBER OF LINE CONNECTION OPENINGS ON THE ITEM. 1A MODE REPLY 0 BSSPD 11METHOD,CONNECTION,LINE OPENING LINE OPENING CONNECTION METHOD THE MEANS USED TO CONNECT THE LINES. SELECT REPLY CODE 10AJ68 BSSQA 13THREAD SIZE,OPENING OPENING THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASURMENT SCALE OF A THREADED OPENING. 1A MODE REPLY 0 BSSRD 13THREAD SERIES DESIGNATOR,OPENING OPENING THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF A THREADED OPENING. SELECT REPLY CODE 10AH06 BSSSD 08LOCATION,BRACKET,MOUNTING MOUNTING BRACKET LOCATION INDICATES THE LOCATION OF THE MOUNTING BRACKET ON THE ITEM. SELECT REPLY CODE 10AJ91 BSSTD 08LOCATION,MECHANISM,OPERATING OPERATING MECHANISM LOCATION INDICATES THE LOCATION OF THE OPERATING MECHANISM ON THE ITEM. SELECT REPLY CODE 10AJ91 BSSWJ 04HEIGHT,RETRACTED RETRACTED HEIGHT A MEASUREMENT FROM THE MOUNTING BASE TO THE TOP OF AN ITEM WHEN RETRACTED,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BSSXJ 04LENGTH,ADJUSTMENT ADJUSTMENT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ADJUSTMENT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BSSYD 02DESIGN,BASE BASE DESIGN THE DESIGN OF THE BASE OF THE ITEM. SELECT REPLY CODE 10AK54 BSSZD /D/ 07FEATURE,ADJUSTMENT,PIN HOLE PIN HOLE ADJUSTMENT FEATURE AN INDICATION OF WHETHER OR NOT A PIN HOLE ADJUSTMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSTBJ 04WIDTH,TIRE TIRE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FLAT SURFACE OF A TIRE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BSTCD /D/ 08LOCATION,OPENING,LOAD LOAD OPENING LOCATION INDICATES THE LOCATION OF THE LOAD OPENING(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 BSTDD /D/ 07DEVICE,LOADING,POWER OPERATED POWER OPERATED LOADING DEVICE AN INDICATION OF WHETHER OR NOT A POWER OPERATED LOADING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 BSTFD 18TYPE,DEVICE,LOADING LOADING DEVICE TYPE INDICATES THE TYPE OF LOADING DEVICE PROVIDED. SELECT REPLY CODE 10AK95 BSTGD /D/ 07COMPACTER,LOAD LOAD COMPACTER AN INDICATION OF WHETHER OR NOT A LOAD COMPACTER IS INCLUDED. SELECT REPLY CODE 10AA49 BSTHD /D/ 07FEATURE,LEAKPROOF LEAKPROOF FEATURE AN INDICATION OF WHETHER OR NOT A LEAKPROOF FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSTJD /D/ 07TANK,SUMP,LIQUID LIQUID SUMP TANK AN INDICATION OF WHETHER OR NOT A LIQUID SUMP TANK IS INCLUDED. SELECT REPLY CODE 10AA49 BSTKD /D/ 07WELL,WHEEL WHEEL WELL AN INDICATION OF WHETHER OR NOT A WHEEL WELL(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BSTLD /D/ 07TAILGATE,ACTUATED,POWER POWER ACTUATED TAILGATE AN INDICATION OF WHETHER OR NOT A POWER ACTUATED TAILGATE IS INCLUDED. SELECT REPLY CODE 10AA49 BSTMJ /D/ 04DISTANCE FROM CAB TO AXLE OF VEHICLE FOR WHICH DESIGNED DISTANCE FROM CAB TO AXLE OF VEHICLE FOR WHICH DESIGNED THE DISTANCE FROM THE CAB TO THE AXLE OF THE VEHICLE FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 BSTND /D/ 08LOCATION,CONVEYOR CONVEYOR LOCATION INDICATES THE LOCATION OF THE CONVEYOR ON THE ITEM. SELECT REPLY CODE 10AJ91 BSTPD /D/ 18TYPE,ATTACHMENT,SPREADING SPREADING ATTACHMENT TYPE INDICATES THE TYPE OF SPREADING ATTACHMENT PROVIDED. SELECT REPLY CODE 10AK54 BSTQJ /D/ 10CAPACITY FOR WHICH DESIGNED,CHASSIS,TRUCK TRUCK CHASSIS CAPACITY FOR WHICH DESIGNED THE CAPACITY OF THE TRUCK CHASSIS FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY12AG67 BSTRD /D/ 07FEATURE,CRADLE CRADLE FEATURE AN INDICATION OF WHETHER OR NOT A CRADLE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSTSD /D/ 07COMPARTMENT,SEALED SEALED COMPARTMENT AN INDICATION OF WHETHER OR NOT A SEALED COMPARTMENT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BSTTD 18TYPE,ACCOMMODATION,WHEEL WELL WHEEL WELL ACCOMMODATION TYPE INDICATES THE TYPE OF WHEEL WELL ACCOMMODATION. SELECT REPLY CODE 10AA78 BSTWJ 04DISTANCE,WHEEL WELL CENTERLINE TO BODY FRONT WHEEL WELL CENTERLINE TO BODY FRONT DISTANCE THE DISTANCE FROM THE WHEEL WELL CENTERLINE TO THE FRONT OF THE BODY. 2D AND 1B MODE REPLY21AA051AC20 BSTXJ /D/ 10CAPACITY RATING,RECEPTACLE RECEPTACLE CAPACITY RATING A MEASUREMENT OF THE CAPACITY FOR WHICH THE RECEPTACLE IS RATED. 1D AND 1B MODE REPLY12AG67 BSTYA 12QUANTITY,MANHOLE MANHOLE QUANTITY THE NUMBER OF MANHOLES INCLUDED. 1A MODE REPLY 0 BSTZD /D/ 07FACILITY,HEATING,TANK CONTENT TANK CONTENT HEATING FACILITY AN INDICATION OF WHETHER OR NOT A TANK CONTENT HEATING FACILITY/IES/ IS INCLUDED. SELECT REPLY CODE 10AA49 BSWBG 08LOCATION,COMPARTMENT,STOWAGE STOWAGE COMPARTMENT LOCATION INDICATES THE LOCATION(S) OF THE STOWAGE COMPARTMENT(S) ON THE ITEM. FULL TEXT WRITE-IN 0 BSWCD /D/ 07CATWALK CATWALK AN INDICATION OF WHETHER OR NOT A CATWALK(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BSWDD /D/ 08LOCATION,CATWALK CATWALK LOCATION INDICATES THE LOCATION(S) OF THE CATWALK(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 BSWFA /D/ 12QUANTITY,EXTINGUISHER,FIRE FIRE EXTINGUISHER QUANTITY THE NUMBER OF FIRE EXTINGUISHERS PROVIDED. 1A MODE REPLY 0 BSWGD /D/ 07FEATURE,LIFT LIFT FEATURE AN INDICATION OF WHETHER OR NOT A LIFT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSWHD 18TYPE,STAKE STAKE TYPE INDICATES THE TYPE OF STAKE(S) PROVIDED ON THE ITEM. SELECT REPLY CODE 10AK54 BSWJD 07ADJUSTABILITY,LEG LEG ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE LEG(S) IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BSWKD 11METHOD,RETRACTING RETRACTING METHOD THE MEANS PROVIDED TO RETRACT AN ITEM. SELECT REPLY CODE 10AL41 BSWLD /D/ 07MECHANISM,RETRACTING RETRACTING MECHANISM AN INDICATION OF WHETHER OR NOT A RETRACTING MECHANISM IS INCLUDED. SELECT REPLY CODE 10AA49 BSWMD 18TYPE,SHAFT,INPUT INPUT SHAFT TYPE INDICATES THE TYPE OF INPUT SHAFT PROVIDED. SELECT REPLY CODE 10AF58 BSWNA 12QUANTITY,SHAFT,INPUT INPUT SHAFT QUANTITY THE NUMBER OF INPUT SHAFTS PROVIDED. 1A MODE REPLY 0 BSWPJ /D/ 04DIAMETER,SHAFT,INPUT,STRAIGHT STRAIGHT INPUT SHAFT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A STRAIGHT INPUT SHAFT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BSWQD 18TYPE,SHAFT,OUTPUT OUTPUT SHAFT TYPE INDICATES THE TYPE OF OUTPUT SHAFT PROVIDED. SELECT REPLY CODE 10AF58 BSWRA 12QUANTITY,SHAFT,OUTPUT OUTPUT SHAFT QUANTITY THE NUMBER OF OUTPUT SHAFTS PROVIDED. 1A MODE REPLY 0 BSWSJ /D/ 04DIAMETER,SHAFT,OUTPUT,STRAIGHT STRAIGHT OUTPUT SHAFT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A STRAIGHT OUTPUT SHAFT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BSWTG 19POSITION,SHAFT SHAFT POSITION THE POSITION OF THE SHAFT(S) ON THE ITEM. FULL TEXT WRITE-IN 0 BSWWG /D/ 10RATIO,FORWARD,FIXED GEAR FIXED GEAR FORWARD RATIO THE RATIO BETWEEN FIXED GEARS FOR FORWARD ACTION. FULL TEXT WRITE-IN 0 BSWXG /D/ 10RATIO,REVERSE,FIXED GEAR FIXED GEAR REVERSE RATIO THE RATIO BETWEEN FIXED GEARS FOR REVERSE ACTION. FULL TEXT WRITE-IN 0 BSWYA /D/ 12QUANTITY,RANGE,TRANSFER TRANSMISSION TRANSFER TRANSMISSION RANGE QUANTITY THE NUMBER OF TRANSFER TRANSMISSION RANGES PROVIDED. 1A MODE REPLY 0 BSWZG /D/ 10RATIO,VARIABLE,MAXIMUM MAXIMUM VARIABLE RATIO THE MAXIMUM VARIABLE RATIO OF THE ITEM. FULL TEXT WRITE-IN 0 BSXBG /D/ 10RATIO,VARIABLE,MINIMUM MINIMUM VARIABLE RATIO THE MINIMUM VARIABLE RATIO OF THE ITEM. FULL TEXT WRITE-IN 0 BSXCD /D/ 07DEVICE,LOCKOUT,MANUALLY ACTUATED FORWARD SPEED MANUALLY ACTUATED FORWARD SPEED LOCKOUT DEVICE AN INDICATION OF WHETHER OR NOT A MANUALLY ACTUATED FORWARD SPEED LOCKOUT DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 BSXDD /D/ 07COOLER,OIL,INTEGRAL INTEGRAL OIL COOLER AN INDICATION OF WHETHER OR NOT AN INTEGRAL OIL COOLER IS INCLUDED. SELECT REPLY CODE 10AA49 BSXFD 18TYPE,TRANSMISSION,TRANSFER TRANSFER TRANSMISSION TYPE INDICATES THE TYPE OF TRANSFER TRANSMISSION PROVIDED. SELECT REPLY CODE 10AM54 BSXGA 12QUANTITY,RANGE RANGE QUANTITY THE NUMBER OF RANGES PROVIDED. 1A MODE REPLY 0 BSXHD /D/ 07FEATURE,ATTACHMENT,EXTERNAL OVERDRIVE EXTERNAL OVERDRIVE ATTACHMENT FEATURE AN INDICATION OF WHETHER OR NOT AN EXTERNAL OVERDRIVE ATTACHMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSXJD /D/ 07OVERDRIVE,EXTERNAL EXTERNAL OVERDRIVE AN INDICATION OF WHETHER OR NOT AN EXTERNAL OVERDRIVE IS INCLUDED. SELECT REPLY CODE 10AA49 BSXKD /D/ 07FEATURE,MOUNTING,POWER TAKEOFF UNIT,SEPARABLE SEPARABLE POWER TAKEOFF UNIT MOUNTING FEATURE AN INDICATION OF WHETHER OR NOT A SEPARABLE POWER TAKEOFF UNIT/S/ MOUNTING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSXLA /D/ 12QUANTITY,ACCOMMODATION,POWER TAKEOFF UNIT POWER TAKEOFF UNIT ACCOMMODATION QUANTITY THE NUMBER OF POWER TAKEOFF UNITS THAT CAN BE ACCOMMODATED. 1A MODE REPLY 0 BSXMA /D/ 12QUANTITY,UNIT,POWER TAKEOFF POWER TAKEOFF UNIT QUANTITY THE NUMBER OF POWER TAKEOFF UNITS FURNISHED WITH THE ITEM. 1A MODE REPLY 0 BSXNG /D/ 10RATIO,GEAR,FORWARD FORWARD GEAR RATIO THE RATIO BETWEEN GEARS FOR FORWARD ACTION. FULL TEXT WRITE-IN 0 BSXPG /D/ 10RATIO,GEAR,REVERSE REVERSE GEAR RATIO THE RATIO BETWEEN GEARS FOR REVERSE ACTION. FULL TEXT WRITE-IN 0 BSXQD /D/ 18TYPE FOR WHICH DESIGNED,BOOSTER,SHIFTING SHIFTING BOOSTER TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF SHIFTING BOOSTER FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BSXRD /D/ 07BOOSTER,SHIFTING SHIFTING BOOSTER AN INDICATION OF WHETHER OR NOT A SHIFTING BOOSTER IS INCLUDED. SELECT REPLY CODE 10AA49 BSXSD 18TYPE,OPERATION OPERATION TYPE INDICATES THE TYPE OF OPERATION BY WHICH THE ITEM IS CONTROLLED. SELECT REPLY CODE 10AK54 BSXTD /D/ 08LOCATION,MOUNTING,CONTROL,SHIFTING SHIFTING CONTROL MOUNTING LOCATION INDICATES THE LOCATION OF THE SHIFTING CONTROL MOUNTING. SELECT REPLY CODE 10AJ91 BSXWG /D/ 19FINISH AND LOCATION,SURFACE,FORK FORK SURFACE FINISH AND LOCATION DESIGNATES THE SURFACE ROUGHNESS RATING REPRESENTING THE ARITHMETIC AVERAGE DEVIATION OF THE SURFACE FROM THE MAINLINE IN A PROFILE AND ITS LOCATION ON THE FORK. FULL TEXT WRITE-IN 0 BSXXD /D/ 07BEARING,HOLE,FORK END FORK END HOLE BEARING AN INDICATION OF WHETHER OR NOT A FORK END HOLE BEARING/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BSXYD /D/ 07BEARING,HOLE,MOUNTING MOUNTING HOLE BEARING AN INDICATION OF WHETHER OR NOT A MOUNTING HOLE BEARING(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BSXZD /D/ 07SPIDER,JOINT,UNIVERSAL UNIVERSAL JOINT SPIDER AN INDICATION OF WHETHER OR NOT A UNIVERSAL JOINT SPIDER IS INCLUDED. SELECT REPLY CODE 10AA49 BSYBD 14SHAPE,BEARING,SPIDER SPIDER BEARING SHAPE THE PHYSICAL CONFIGURATION OF THE SPIDER BEARING. SELECT REPLY CODE 10AD07 BSYCD 18TYPE,RETAINER,SPIDER BEARING SPIDER BEARING RETAINER TYPE INDICATES THE TYPE OF SPIDER BEARING RETAINER PROVIDED. SELECT REPLY CODE 10AK54 BSYDD /D/ 19FACILITY,MOUNTING,SPIDER BEARING SPIDER BEARING MOUNTING FACILITY THE FACILITY USED FOR MOUNTING THE SPIDER BEARING/S/. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. SELECT REPLY CODE 10AM39 BSYFD /D/ 07FINISH,SURFACE,MACHINED,OUTER PERIPHERY OUTER PERIPHERY MACHINED SURFACE FINISH AN INDICATION OF WHETHER OR NOT AN OUTER PERIPHERY MACHINED SURFACE FINISH IS INCLUDED. SELECT REPLY CODE 10AA49 BSYGD /D/ 07FEATURE,HUB,SPLIT SPLIT HUB FEATURE AN INDICATION OF WHETHER OR NOT A SPLIT HUB FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSYHD /D/ 07BOLT,HUB,SPLIT SPLIT HUB BOLT AN INDICATION OF WHETHER OR NOT A BOLT/S/ IS FURNISHED FOR A SPLIT HUB. SELECT REPLY CODE 10AA55 BSYJD 07PROVISION,THREAD,HUB END HUB END THREAD PROVISION AN INDICATION OF WHETHER OR NOT THE HUB END IS THREADED. SELECT REPLY CODE 10AE00 BSYKD /D/ 07CAP,RETAINING,PACKING PACKING RETAINING CAP AN INDICATION OF WHETHER OR NOT A PACKING RETAINING CAP IS INCLUDED. SELECT REPLY CODE 10AA49 BSYLD /D/ 07BORE,HUB HUB BORE AN INDICATION OF WHETHER OR NOT A HUB BORE IS INCLUDED. SELECT REPLY CODE 10AA49 BSYMD /D/ 07SLOT,TITLE TITLE SLOT AN INDICATION OF WHETHER OR NOT A TITLE SLOT IS INCLUDED. PLEASE USE MRC BCRG IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BSYND /D/ 07FEATURE,INSCRIPTION,REVERSE REVERSE INSCRIPTION FEATURE AN INDICATION OF WHETHER OR NOT A REVERSE INSCRIPTION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BSYPJ B04SIZE,SPACE,WINDOW WINDOW SPACE SIZE DESIGNATES THE SIZE OF THE WINDOW SPACE PROVIDED ON THE ITEM. 1D AND 1F MODE REPLY11AA05 BSYQJ /D/ 04LENGTH,CARD/LABEL,ACCOMMODATED ACCOMMODATED CARD/LABEL LENGTH A MEASUREMENT OF THE CARD AND/OR LABEL THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BSYRJ /D/ 04WIDTH,CARD/LABEL,ACCOMMODATED ACCOMMODATED CARD/LABEL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CARD AND/OR LABEL THAT THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BSYSD /D/ 07SHIELD,WINDOW WINDOW SHIELD AN INDICATION OF WHETHER OR NOT A WINDOW SHIELD IS INCLUDED. SELECT REPLY CODE 10AA49 BSYTD 18TYPE,ADJUSTMENT,MECHANICAL MECHANICAL ADJUSTMENT TYPE INDICATES THE TYPE OF MECHANICAL ADJUSTMENT PROVIDED ON THE ITEM. SELECT REPLY CODE 10AJ74 BSYWD /D/ 07COVER,CARD,INNER INNER CARD COVER AN INDICATION OF WHETHER OR NOT AN INNER COVER IS INCLUDED. SELECT REPLY CODE 10AA49 BSYXJ 04WIDTH,HOLDER HOLDER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE HOLDER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BSYYD 18TYPE,ADJUSTMENT ADJUSTMENT TYPE INDICATES THE TYPE OF ADJUSTMENT INCLUDED IN THE ITEM. SELECT REPLY CODE 10AC58 BSYZD 07ADJUSTABILITY,COMPARTMENT COMPARTMENT ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE COMPARTMENT(S) IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BSZBD 18TYPE,PARTITION PARTITION TYPE INDICATES THE TYPE OF PARTITION(S) PROVIDED. SELECT REPLY CODE 10AK54 BSZCJ 04DISTANCE BETWEEN COMPARTMENTS DISTANCE BETWEEN COMPARTMENTS THE DISTANCE BETWEEN COMPARTMENTS. 1D AND 1B MODE REPLY11AA05 BSZFD /D/ 07SPACE,INDEX INDEX SPACE AN INDICATION OF WHETHER OR NOT AN INDEX SPACE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BSZGD 18TYPE,SECTION SECTION TYPE INDICATES THE TYPE OF SECTION PROVIDED. SELECT REPLY CODE 10AK54 BSZHJ 04LENGTH,BACK BACK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A BACK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BSZJA 12QUANTITY,TRAY,TIERED TIERED TRAY QUANTITY THE NUMBER OF TIERED TRAYS PROVIDED. 1A MODE REPLY 0 BSZKD /D/ 07STRAP,ARM ARM STRAP AN INDICATION OF WHETHER OR NOT AN ARM STRAP IS INCLUDED. PLEASE USE MRC CDGG IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BSZLD /D/ 07PADS,PROTECTIVE PROTECTIVE PADS AN INDICATION OF WHETHER OR NOT PROTECTIVE PADS ARE INCLUDED. SELECT REPLY CODE 10AA49 BSZMA 12QUANTITY,HANDRAIL HANDRAIL QUANTITY THE NUMBER OF HANDRAILS PROVIDED. 1A MODE REPLY 0 BSZND /D/ 09MATERIAL,RAIL,SIDE SIDE RAIL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SIDE RAIL/S/ IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BSZPJ 04LENGTH,RAIL,SIDE SIDE RAIL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SIDE RAIL(S),IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BSZQJ /D/A18TYPE AND QUANTITY,CROSSPIECE CROSSPIECE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF CROSSPIECES PROVIDED. 1D AND 1A MODE REPLY13AK54 BSZRD /D/ 09MATERIAL,RUNG RUNG MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE RUNG IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BSZSD /D/ 09MATERIAL,STEP STEP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE STEP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BSZTJ 04LENGTH,CROSSPIECE CROSSPIECE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CROSSPIECE OF AN ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BSZWD /D/ 07TREAD,CROSSPIECE CROSSPIECE TREAD AN INDICATION OF WHETHER OR NOT A CROSSPIECE TREAD IS INCLUDED. SELECT REPLY CODE 10AA49 BSZXD /D/ 09MATERIAL,TREAD TREAD MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TREAD IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BSZYD /D/ 07SHOES,SAFETY SAFETY SHOES AN INDICATION OF WHETHER OR NOT SAFETY SHOES ARE INCLUDED. SELECT REPLY CODE 10AA49 BSZZD 18TYPE,CROSSPIECE CROSSPIECE TYPE INDICATES THE TYPE OF CROSSPIECE PROVIDED. SELECT REPLY CODE 10AK54 BTBBD /D/ 07HOOKS,ATTACHMENT ATTACHMENT HOOKS AN INDICATION OF WHETHER OR NOT ATTACHMENT HOOKS ARE INCLUDED. SELECT REPLY CODE 10AA49 BTBCD /D/ 18TYPE,SURFACE,CROSSPIECE CROSSPIECE SURFACE TYPE INDICATES THE TYPE OF SURFACE ON THE CROSSPIECE. SELECT REPLY CODE 10AK54 BTBDD 18TYPE,PLATFORM PLATFORM TYPE INDICATES THE TYPE OF PLATFORM PROVIDED. SELECT REPLY CODE 10AK54 BTBFD /D/ 07GUARD,PLATFORM PLATFORM GUARD AN INDICATION OF WHETHER OR NOT A PLATFORM GUARD IS INCLUDED. SELECT REPLY CODE 10AA49 BTBGJ 04DISTANCE FROM FLOOR TO PLATFORM TOP DISTANCE FROM FLOOR TO PLATFORM TOP THE DISTANCE FROM THE FLOOR TO THE TOP OF THE PLATFORM. 2D AND 1B MODE REPLY21AA051AC20 BTBHD /D/ 07FEET,SAFETY SAFETY FEET AN INDICATION OF WHETHER OR NOT SAFETY FEET ARE INCLUDED. SELECT REPLY CODE 10AA49 BTBJD /D/ 18TYPE,FEET,SAFETY SAFETY FEET TYPE INDICATES THE TYPE OF SAFETY FEET PROVIDED. SELECT REPLY CODE 10AK54 BTBKD /D/ 07LOCK,SAFETY SAFETY LOCK AN INDICATION OF WHETHER OR NOT A SAFETY LOCK/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BTBLD /D/ 07ROPE/PULLEY ROPE/PULLEY AN INDICATION OF WHETHER OR NOT A ROPE AND PULLEY ARE INCLUDED. SELECT REPLY CODE 10AA49 BTBMD /D/ 07HOLE,SECURING,HUB HUB SECURING HOLE AN INDICATION OF WHETHER OR NOT A HUB SECURING HOLE IS INCLUDED. SELECT REPLY CODE 10AA49 BTBNG 08LOCATION,HOLE,SECURING SECURING HOLE LOCATION INDICATES THE LOCATION OF THE SECURING HOLE ON THE ITEM. FULL TEXT WRITE-IN 0 BTBPA /D/ 19NUMBER,PIN,ACCOMMODATED TAPER,SECURING HOLE SECURING HOLE ACCOMMODATED TAPER PIN NUMBER THE NUMERIC DESIGNATION FOR THE TAPER PIN ACCOMMODATED BY A SECURING HOLE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. 1A MODE REPLY 0 BTBQA 13THREAD SIZE DESIGNATOR,HOLE,SECURING SECURING HOLE THREAD SIZE DESIGNATOR DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE FOR A THREADED SECURING HOLE(S). 1A MODE REPLY 0 BTBRD 18TYPE,SPLINE,SHAFT END SHAFT END SPLINE TYPE INDICATES THE TYPE OF SPLINE(S) ON THE END OF THE SHAFT. SELECT REPLY CODE 10AA85 BTBSJ 04LENGTH FROM UNIVERSAL JOINT SPIDER CENTERLINE TO SHAFT END LENGTH FROM UNIVERSAL JOINT SPIDER CENTERLINE TO SHAFT END A MEASUREMENT OF THE LONGEST DIMENSION FROM THE CENTERLINE OF THE UNIVERSAL JOINT SPIDER TO THE SHAFT END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BTBTA /D/ 16STYLE,JOINT,UNIVERSAL UNIVERSAL JOINT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE UNIVERSAL JOINT. 1A MODE REPLY 0 BTBWD /D/ 07CLUTCH,SAFETY SAFETY CLUTCH AN INDICATION OF WHETHER OR NOT A SAFETY CLUTCH IS INCLUDED. SELECT REPLY CODE 10AA49 BTBXH 18TYPE AND LOCATION,COMPONENT,END END COMPONENT TYPE AND LOCATION INDICATES THE TYPE AND LOCATION OF THE END COMPONENT(S). 2D MODE REPLY 23AK843AJ91 BTBYL 16STYLE,END,SHAFT SHAFT END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SHAFT END. 1L MODE REPLY 0 BTBZD 14SHAPE,OUTSIDE OUTSIDE SHAPE THE PHYSICAL CONFIGURATION OF THE OUTSIDE OF THE ITEM. SELECT REPLY CODE 10AD07 BTCBA /D/ 16STYLE,FORK,YOKE YOKE FORK STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE YOKE FORK. 1A MODE REPLY 0 BTCCD /D/ 18TYPE,END,CONNECTION,UNIVERSAL JOINT UNIVERSAL JOINT CONNECTION END TYPE INDICATES THE TYPE OF CONNECTION END(S) ON THE UNIVERSAL JOINT. SELECT REPLY CODE 10AK84 BTCDD 07PROVISION,THREAD,SHAFT END SHAFT END THREAD PROVISION AN INDICATION OF WHETHER OR NOT THE SHAFT END IS THREADED.MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. SELECT REPLY CODE 10AE00 BTCFD /D/ 07DEFLECTOR,DIRT-LIQUID DIRT-LIQUID DEFLECTOR AN INDICATION OF WHETHER OR NOT A DIRT AND LIQUID DEFLECTOR IS INCLUDED. SELECT REPLY CODE 10AA49 BTCGD /D/ 07FEATURE,CONSTRUCTION,LAMINATED LAMINATED CONSTRUCTION FEATURE AN INDICATION OF WHETHER OR NOT A LAMINATED CONSTRUCTION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BTCHD /D/ 09MATERIAL,GEAR GEAR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE GEAR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BTCJG 10RATIO,GEAR GEAR RATIO THE RATIO RELATIONSHIP BETWEEN GEARS. FULL TEXT WRITE-IN 0 BTCKF T10RANGE IN DEG,OPERATING,ANGULAR ANGULAR OPERATING RANGE IN DEG THE RANGE OF ANGLES WITHIN WHICH THE ITEM WILL OPERATE,EXPRESSED IN DEGREES. 1F MODE REPLY 0 BTCLD /D/ 18TYPE,BRACKET,MOUNTING MOUNTING BRACKET TYPE INDICATES THE TYPE OF MOUNTING BRACKET PROVIDED. SELECT REPLY CODE 10AM39 BTCMD /D/ 07COUPLING,EXPANSION EXPANSION COUPLING AN INDICATION OF WHETHER OR NOT AN EXPANSION COUPLING IS INCLUDED. SELECT REPLY CODE 10AA49 BTCND /D/ 09MATERIAL,BELLOWS BELLOWS MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BELLOWS ARE FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BTCPD /D/ 07COVER,CHAIN CHAIN COVER AN INDICATION OF WHETHER OR NOT A CHAIN COVER IS INCLUDED. SELECT REPLY CODE 10AA49 BTCQD /D/ 07BOLT,COUPLING COUPLING BOLT AN INDICATION OF WHETHER OR NOT A COUPLING BOLT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BTCRJ /D/ 04LENGTH,FACILITY,KEYING KEYING FACILITY LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A KEYING FACILITY,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BTCSL /D/ 16STYLE,HOLE,POSITIONING POSITIONING HOLE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE HOLE(S) PROVIDED FOR POSITIONING THE ITEM. 1L MODE REPLY 0 BTCTA /D/ 13THREAD SIZE DESIGNATOR,HOLE HOLE THREAD SIZE DESIGNATOR DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE FOR A THREADED HOLE. 1A MODE REPLY 0 BTCWA 12QUANTITY,RUNG RUNG QUANTITY THE NUMBER OF RUNGS PROVIDED. 1A MODE REPLY 0 BTCXJ 04WIDTH,RUNG RUNG WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE RUNG,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BTCYJ 04THICKNESS,RUNG RUNG THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A RUNG,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BTCZB /D/ 10SPEED IN RPM,RATED,MAXIMUM,INPUT SHAFT INPUT SHAFT MAXIMUM RATED SPEED IN RPM THE MAXIMUM SPEED FOR WHICH THE INPUT SHAFT HAS BEEN TESTED AND RATED,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 BTDBB /D/ 10HORSEPOWER RATING,UNIT,GEAR ASSEMBLY GEAR ASSEMBLY UNIT HORSEPOWER RATING THE RATED HORSEPOWER OF THE GEAR ASSEMBLY UNIT. 1B MODE REPLY 0 BTDCJ /D/ 04LENGTH,OVERALL,GEAR ASSEMBLY GEAR ASSEMBLY OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE GEAR ASSEMBLY. 2D AND 1B MODE REPLY21AA051AC20 BTDDJ /D/ 04WIDTH,OVERALL,GEAR ASSEMBLY GEAR ASSEMBLY OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE GEAR ASSEMBLY,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BTDFJ /D/ 04DIAMETER,OVERALL,GEAR ASSEMBLY GEAR ASSEMBLY OVERALL DIAMETER THE OVERALL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A GEAR ASSEMBLY,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BTDGJ /D/ 04HEIGHT,OVERALL,GEAR ASSEMBLY GEAR ASSEMBLY OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE GEAR ASSEMBLY. 2D AND 1B MODE REPLY21AA051AC20 BTDHJ 04DIAMETER,OUTSIDE,JAW CIRCLE JAW CIRCLE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BTDJJ 04LENGTH,PROJECTION,JAW JAW PROJECTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTDKJ 04DIAMETER,INSIDE,JAW CIRCLE JAW CIRCLE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BTDLB 04LENGTH IN DEG,ARC,JAW JAW ARC LENGTH IN DEG NONE. 1B MODE REPLY 0 BTDMG 18TYPE ACCOMMODATED,RING RING TYPE ACCOMMODATED INDICATES THE TYPE OF RING(S) THE ITEM IS DESIGNED TO ACCOMMODATE. FULL TEXT WRITE-IN 0 BTDNG /D/ 04DIAMETER,RING SIZE/PLIERS TIP RING SIZE/PLIERS TIP DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE RING SIZE AND/OR PLIERS TIP,AND TERMINATES AT THE CIRCUMFERENCE. FULL TEXT WRITE-IN 0 BTDPD /D/ 07FEATURE,OPERATED,HYDRAULICALLY HYDRAULICALLY OPERATED FEATURE AN INDICATION OF WHETHER OR NOT A HYDRAULICALLY OPERATED FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BTDQD /D/ 07JAW,BACK,SWIVEL SWIVEL BACK JAW AN INDICATION OF WHETHER OR NOT A SWIVEL BACK JAW IS PROVIDED. SELECT REPLY CODE 10AB22 BTDRD /D/ 07FEATURE,BACK,ANVIL ANVIL BACK FEATURE AN INDICATION OF WHETHER OR NOT AN ANVIL BACK FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BTDSD /D/ 07REMOVABILITY,FACE,JAW JAW FACE REMOVABILITY AN INDICATION OF WHETHER OR NOT A JAW FACE(S) IS REMOVABLE. SELECT REPLY CODE 10AB00 BTDTJ 10SIZE ACCOMMODATED,PIPE PIPE SIZE ACCOMMODATED DESIGNATES THE PIPE SIZE THE ITEM WILL ACCOMMODATE. 2D AND 1B MODE REPLY21AA051AC20 BTDWJ /D/T10RANGE,ACCOMMODATED,CHAIN PITCH CHAIN PITCH ACCOMMODATED RANGE THE MINIMUM AND MAXIMUM VALUES OF THE CHAIN PITCH THE ITEM WILL ACCOMMODATE. 1D AND 1F MODE REPLY11AA05 BTDXJ 04LENGTH,END,MALE MALE END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTDYJ 04LENGTH,END,FEMALE FEMALE END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTDZJ 10RANGE,SPREAD SPREAD RANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BTFBJ 04THICKNESS,TIP TIP THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A TIP,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BTFCJ 04DIAMETER,END,NOSE NOSE END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A NOSE END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BTFDJ 04WIDTH,END,NOSE NOSE END WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTFGJ 04WIDTH,NOMINAL,JAW JAW NOMINAL WIDTH A NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A JAW,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BTFHJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,END,MALE MALE END THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE MALE END. 1D AND 1A MODE REPLY12AH06 BTFJA 13THREAD CLASS,END,MALE MALE END THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL MALE END THREAD. 1A MODE REPLY 0 BTFKJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,END,FEMALE FEMALE END THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE FEMALE END. 1D AND 1A MODE REPLY12AH06 BTFLA 13THREAD CLASS,END,FEMALE FEMALE END THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN INTERNAL FEMALE END THREAD. 1A MODE REPLY 0 BTFMJ 04DIAMETER ACCOMMODATED,RING RING DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR A RING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BTFNJ 04DIAMETER ACROSS FLATS DIAMETER ACROSS FLATS THE LENGTH OF A STRAIGHT LINE WHICH PASSES ACROSS THE CENTER OF THE FLATS,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BTFPJ 04DIAMETER,HOLE,HANDLE MOUNTING HANDLE MOUNTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HANDLE MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BTFQA 12QUANTITY,COLLAR,DRIVER DRIVER COLLAR QUANTITY THE NUMBER OF DRIVER COLLARS PROVIDED. 1A MODE REPLY 0 BTFRJ 10SIZE,PLATE,TAPPET TAPPET PLATE SIZE DESIGNATES THE SIZE OF THE TAPPET PLATE. 2D AND 1B MODE REPLY21AA051AC20 BTFSJ 10CAPACITY,OPENING OPENING CAPACITY THE OPENING CAPACITY OF AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 BTFTD /D/ 07ADJUSTMENT,DEPTH DEPTH ADJUSTMENT AN INDICATION OF WHETHER OR NOT AN ADJUSTMENT FOR DEPTH IS INCLUDED. SELECT REPLY CODE 10AA49 BTFWA 12QUANTITY,JAW,STRAIGHT STRAIGHT JAW QUANTITY THE NUMBER OF STRAIGHT JAWS PROVIDED. 1A MODE REPLY 0 BTFXA 12QUANTITY,JAW,OFFSET OFFSET JAW QUANTITY THE NUMBER OF OFFSET JAWS PROVIDED. 1A MODE REPLY 0 BTFYD /D/ 02DESIGN,USAGE,OFFSET JAW OFFSET JAW USAGE DESIGN AN INDICATION OF THE DESIGNED USE OF THE OFFSET JAW. SELECT REPLY CODE 10AK54 BTFZD /D/ 07COMPRESSOR,SPRING SPRING COMPRESSOR AN INDICATION OF WHETHER OR NOT A SPRING COMPRESSOR IS PROVIDED. SELECT REPLY CODE 10AB22 BTGBA 12QUANTITY,HOLDER,SPRING SPRING HOLDER QUANTITY THE NUMBER OF SPRING HOLDERS PROVIDED. 1A MODE REPLY 0 BTGCJ 04DIAMETER,MIRROR MIRROR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MIRROR,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BTGDG 04SIZE ACCOMMODATED,STUD STUD SIZE ACCOMMODATED DESIGNATES THE STUD SIZE THE ITEM WILL ACCOMMODATE. FULL TEXT WRITE-IN 0 BTGFJ 10RANGE,SPREAD,EXPANDING COLLET EXPANDING COLLET SPREAD RANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BTGGJ 10RANGE,SPREAD,ENGAGING TAP ENGAGING TAP SPREAD RANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BTGHJ 10RANGE,SPREAD,ENGAGING BUSHING ENGAGING BUSHING SPREAD RANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BTGJJ 10RANGE,SPREAD,INSTALLING PLATE INSTALLING PLATE SPREAD RANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BTGKJ 10RANGE,SPREAD,PULLING ADAPTER PULLING ADAPTER SPREAD RANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BTGLJ 10RANGE,ARBOR,EXPANDING EXPANDING ARBOR RANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BTGMD /D/ 09MATERIAL,ROLL ROLL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ROLL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BTGND /D/ 07SPINDLE SPINDLE AN INDICATION OF WHETHER OR NOT A SPINDLE IS INCLUDED. SELECT REPLY CODE 10AA49 BTGPG 08LOCATION,SCALE SCALE LOCATION INDICATES THE LOCATION OF THE SCALE ON THE ITEM. FULL TEXT WRITE-IN 0 BTGQD 07FEATURE,RADIOACTIVE RADIOACTIVE FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM IS RADIOACTIVE. SELECT REPLY CODE 10AB54 BTGRD /D/ 07MARKINGS,FILLED FILLED MARKINGS AN INDICATION OF WHETHER OF NOT FILLED MARKINGS ARE PROVIDED. SELECT REPLY CODE 10AB22 BTGSD /D/ 07GRADUATED TO TIP GRADUATED TO TIP AN INDICATION OF WHETHER OR NOT GRADUATIONS TO THE TIP OF THE ITEM ARE PROVIDED. SELECT REPLY CODE 10AB22 BTGTD /D/ 07ADJUSTMENT FOR BLOWING OUT LAST DROP,VOLUME VOLUME ADJUSTMENT FOR BLOWING OUT LAST DROP AN INDICATION OF WHETHER OR NOT A VOLUME ADJUSTMENT FOR BLOWING OUT THE LAST DROP IS PROVIDED. SELECT REPLY CODE 10AB22 BTGWD /D/ 08LOCATION,BULB BULB LOCATION INDICATES THE LOCATION OF THE BULB ON THE ITEM. SELECT REPLY CODE 10AJ91 BTGXD /D/ 07STOPCOCK STOPCOCK AN INDICATION OF WHETHER OR NOT A STOPCOCK IS PROVIDED. SELECT REPLY CODE 10AB22 BTGYD /D/ 07TIP,ELONGATED ELONGATED TIP AN INDICATION OF WHETHER OR NOT AN ELONGATED TIP IS PROVIDED. SELECT REPLY CODE 10AB22 BTGZD /D/ 07TIP,CAPILLARY CAPILLARY TIP AN INDICATION OF WHETHER OR NOT A CAPILLARY TIP IS PROVIDED. SELECT REPLY CODE 10AB22 BTHBD /D/ 07FEATURE,FILLING,CAPILLARY ACTION CAPILLARY ACTION FILLING FEATURE AN INDICATION OF WHETHER OR NOT A FILLING FEATURE BY CAPILLARY ACTION IS PROVIDED. SELECT REPLY CODE 10AB22 BTHCD /D/ 07CAPILLARY AT GRADUATION MARK CAPILLARY AT GRADUATION MARK AN INDICATION OF WHETHER OR NOT A CAPILLARY AT GRADUATION MARK IS PROVIDED. SELECT REPLY CODE 10AB22 BTHDD /D/ 07TUBING/MOUTHPIECE TUBING/MOUTHPIECE AN INDICATION OF WHETHER OR NOT A TUBING AND/OR MOUTHPIECE IS PROVIDED. SELECT REPLY CODE 10AB22 BTHFJ /D/ 04LENGTH,TUBE,GLASS GLASS TUBE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A GLASS TUBE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BTHGD /D/ 01COLOR,PELLET PELLET COLOR THE HUE OR TINT OF THE PELLET. SELECT REPLY CODE 10AD06 BTHHF /D/T10RATIO,DILUTION DILUTION RATIO THE PROPORTION OF THE SUBSTANCE TO BE DILUTED TO THE DILUTING ELEMENT. 1F MODE REPLY 0 BTHJD /D/ 07CERTIFICATION,NATIONAL BUREAU OF STANDARDS NATIONAL BUREAU OF STANDARDS CERTIFICATION AN INDICATION OF WHETHER OR NOT A NATIONAL BUREAU OF STANDARDS STAMP OF CERTIFICATION IS PROVIDED. SELECT REPLY CODE 10AB22 BTHLD /D/ 07BULB,OVERFLOW,SAFETY SAFETY OVERFLOW BULB AN INDICATION OF WHETHER OR NOT A SAFETY OVERFLOW BULB IS PROVIDED. SELECT REPLY CODE 10AB22 BTHMD /D/ 07ACCURACY,NATIONAL BUREAU OF STANDARDS NATIONAL BUREAU OF STANDARDS ACCURACY AN INDICATION OF WHETHER OR NOT A TOLERANCE FOR ACCURACY AS ESTABLISHED BY THE NATIONAL BUREAU OF STANDARDS IS PROVIDED. SELECT REPLY CODE 10AB22 BTHND 19CERTIFIER,ACCURACY ACCURACY CERTIFIER THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZAITON ATTESTING TO THE TOLERANCE ACCURACY OF THE ITEM. SELECT REPLY CODE 10AM46 BTHPD /D/ 07CLOSURE,BOTTLE,BULB INCORPORATED BULB INCORPORATED BOTTLE CLOSURE AN INDICATION OF WHETHER OR NOT A BULB IS PROVIDED AS PART OF THE BOTTLE CLOSURE. SELECT REPLY CODE 10AB22 BTHQD /D/ 09MATERIAL,CLOSURE,BOTTLE BOTTLE CLOSURE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BOTTLE CLOSURE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BTHRL 16STYLE,TOP TOP STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TOP. 1L MODE REPLY 0 BTHSL /D/ 16STYLE,BOTTOM BOTTOM STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BOTTOM. 1L MODE REPLY 0 BTHTL /D/ 16STYLE,HEAD,DISTILLING DISTILLING HEAD STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE DISTILLING HEAD. 1L MODE REPLY 0 BTHWJ /D/A19CONNECTION A CONNECTION A NONE. 1D AND 1A MODE REPLY13AM35 BTHXJ /D/A19CONNECTION B CONNECTION B NONE. 1D AND 1A MODE REPLY13AM35 BTHYJ /D/A19CONNECTION C CONNECTION C NONE. 1D AND 1A MODE REPLY13AM35 BTHZJ /D/A19CONNECTION D CONNECTION D NONE. 1D AND 1A MODE REPLY13AM35 BTJBL /D/ 16STYLE,TUBE/ADAPTER,CONNECTING CONNECTING TUBE/ADAPTER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CONNECTING TUBE AND/OR ADAPTER. 1L MODE REPLY 0 BTJCG /D/ 04SIZE,END,SOCKET SOCKET END SIZE NONE. FULL TEXT WRITE-IN 0 BTJDG /D/ 04SIZE,END,FIRST BALL FIRST BALL END SIZE NONE. FULL TEXT WRITE-IN 0 BTJFG /D/ 04SIZE,END,SECOND BALL SECOND BALL END SIZE NONE. FULL TEXT WRITE-IN 0 BTJGL /D/ 16STYLE,TUBE,DRYING DRYING TUBE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE DRYING TUBE. 1L MODE REPLY 0 BTJHJ /D/A04SIZE,INLET,FIRST FIRST INLET SIZE NONE. 1D AND 1A MODE REPLY13AM35 BTJJJ /D/A04SIZE,INLET,SECOND SECOND INLET SIZE NONE. 1D AND 1A MODE REPLY13AM35 BTJKJ /D/ 04DIAMETER,OUTSIDE,FIRST CONNECTION ARM FIRST CONNECTION ARM OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BTJLJ /D/ 04DIAMETER,OUTSIDE,SECOND CONNECTION ARM SECOND CONNECTION ARM OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BTJMJ /D/ 04DISTANCE FROM MOUNTING FACILITY CENTERLINE TO ARCH CENTERLINE DISTANCE FROM MOUNTING FACILITY CENTERLINE TO ARCH CENTERLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 BTJNJ /D/ 04WIDTH,FORK,SECOND ARCH SECOND ARCH FORK WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTJPJ 04WIDTH,END,FORK FORK END WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A FORK, IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BTJQJ 04RADIUS,INSIDE,ARCH ARCH INSIDE RADIUS A MEASUREMENT OF A LINE SEGMENT EXTENDING FROM THE CENTER OF AN ARCH TO THE INSIDE SURFACE. 2D AND 1B MODE REPLY21AA051AC20 BTJRJ /D/ 04RADIUS,INSIDE,SECOND ARCH SECOND ARCH INSIDE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BTJSJ /D/ 04WIDTH,OPENING,FORK END FORK END OPENING WIDTH NONE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 2D AND 1B MODE REPLY21AA051AC20 BTJTJ /D/ 04HEIGHT,OPENING,FORK END FORK END OPENING HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BTJWG /D/ 04SIZE,HOLE,FORK END FORK END HOLE SIZE NONE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. FULL TEXT WRITE-IN 0 BTJXD /D/ 18TYPE,SPRING,INTERNAL GEAR/GRID INTERNAL GEAR/GRID SPRING TYPE INDICATES THE TYPE OF INTERNAL GEAR AND/OR GRID SPRING PROVIDED. SELECT REPLY CODE 10AK54 BTJYD 18TYPE,BOLT BOLT TYPE INDICATES THE TYPE OF BOLT PROVIDED. SELECT REPLY CODE 10AK54 BTJZJ /D/ 04THICKNESS,PROJECTION,FORK END FORK END PROJECTION THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BTKBJ /D/ 04LENGTH,PROJECTION,FORK END FORK END PROJECTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTKCJ 04DISTANCE BETWEEN ARCH CENTER LINES DISTANCE BETWEEN ARCH CENTER LINES NONE. 2D AND 1B MODE REPLY21AA051AC20 BTKDJ 04DIAMETER,HOLE,BEARING BEARING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BTKFJ /D/ 04DEPTH,RECESS/KEYWAY,BEARING BEARING RECESS/KEYWAY DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTKGJ 04DISTANCE FROM FLANGE TO YOKE DISTANCE FROM FLANGE TO YOKE NONE. 2D AND 1B MODE REPLY21AA051AC20 BTKHJ /D/ 04DISTANCE FROM CENTERLINE TO KEYING FACILITY DISTANCE FROM CENTERLINE TO KEYING FACILITY NONE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 2D AND 1B MODE REPLY21AA051AC20 BTKJJ /D/ 04DISTANCE ACROSS FLATS,MAJOR MAJOR DISTANCE ACROSS FLATS NONE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 2D AND 1B MODE REPLY21AA051AC20 BTKKJ /D/ 04DISTANCE ACROSS FLATS,MINOR MINOR DISTANCE ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 BTKLJ 04DISTANCE ACROSS CORNERS DISTANCE ACROSS CORNERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BTKMJ /D/ 04LENGTH,LEG,TRIANGLE TRIANGLE LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTKNJ /D/ 04DISTANCE FROM CENTERLINE OF SHAFT TO COLLAR FACE DISTANCE FROM CENTERLINE OF SHAFT TO COLLAR FACE NONE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. 2D AND 1B MODE REPLY21AA051AC20 BTKPJ /D/ 04WIDTH,KEY,DIFFERENTIATING DIFFERENTIATING KEY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTKQJ /D/ 04WIDTH,KEYWAY,DIFFERENTIATING DIFFERENTIATING KEYWAY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTKRJ /D/ 04HEIGHT,KEY,DIFFERENTIATING DIFFERENTIATING KEY HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BTKSJ /D/ 04DEPTH,KEYWAY,DIFFERENTIATING DIFFERENTIATING KEYWAY DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTKTJ /D/ 04DISTANCE FROM BORE CENTERLINE TO BOTTOM OF KEYING FACILITY DISTANCE FROM BORE CENTERLINE TO BOTTOM OF KEYING FACILITY NONE. 2D AND 1B MODE REPLY21AA051AC20 BTKWJ /D/ 04LENGTH,SLOT,LARGE END CROSS KEY LARGE END CROSS KEY SLOT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTKXJ /D/ 04TAPER PER FOOT,SLOT,CROSS KEY CROSS KEY SLOT TAPER PER FOOT NONE. 2D AND 1B MODE REPLY21AA051AC20 BTKYJ /D/ 04WIDTH,SLOT,CROSS KEY CROSS KEY SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTKZJ /D/ 04WIDTH,FACILITY,KEYING,BODY BODY KEYING FACILITY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTLBJ /D/ 04DEPTH/HEIGHT,KEYING FACILITY,BODY BODY KEYING FACILITY DEPTH/HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BTLCJ /D/ 04DISTANCE FROM BORE CENTERLINE TO BODY KEYING FACILITY BOTTOM/TOP DISTANCE FROM BORE CENTERLINE TO BODY KEYING FACILITY BOTTOM/TOP NONE. 2D AND 1B MODE REPLY21AA051AC20 BTLDJ /D/ 04DISTANCE BETWEEN CENTERLINES OF BORE AND BODY KEYING FACILITY,OFFSET OFFSET DISTANCE BETWEEN CENTERLINES OF BORE AND BODY KEYING FACILITY NONE. 2D AND 1B MODE REPLY21AA051AC20 BTLFJ /D/ 04WIDTH,SLOT,POSITIONING POSITIONING SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTLGB /D/ 04ANGLE,INCLUDED,POSITIONING SLOT POSITIONING SLOT INCLUDED ANGLE NONE. 1B MODE REPLY 0 BTLHA /D/ 12QUANTITY,FACILITY,POSITIONING POSITIONING FACILITY QUANTITY NONE. 1A MODE REPLY 0 BTLJJ /D/ 04DIAMETER,CIRCLE,BOLT,POSITIONING FACILITY POSITIONING FACILITY BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BTLKJ /D/ 04DIAMETER,INSIDE,GROOVE GROOVE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BTLLJ /D/ 04THICKNESS,FACE,RAISED RAISED FACE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BTLMD 11METHOD FOR WHICH DESIGNED,ATTACHMENT ATTACHMENT METHOD FOR WHICH DESIGNED THE ATTACHMENT MEANS FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AA78 BTLNA 12QUANTITY,CONNECTION,HOSE HOSE CONNECTION QUANTITY THE NUMBER OF HOSE CONNECTIONS PROVIDED. 1A MODE REPLY 0 BTLPD /D/ 07CONTAINER,METAL,SEALED SEALED METAL CONTAINER AN INDICATION OF WHETHER OR NOT A SEALED METAL CONTAINER IS PROVIDED. SELECT REPLY CODE 10AB22 BTLQA 12QUANTITY,FILTER,MASK MASK FILTER QUANTITY THE NUMBER OF MASK FILTERS REQUIRED. 1A MODE REPLY 0 BTLRD 19PROTECTION FOR WHICH FILTER IS DESIGNED PROTECTION FOR WHICH FILTER IS DESIGNED AN INDICATION OF THE PROTECTION FOR WHICH THE FILTER IS DESIGNED. SELECT REPLY CODE 10AA65 BTLSD /D/ 07VALVE,EXHAUST EXHAUST VALVE AN INDICATION OF WHETHER OR NOT AN EXHAUST VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 BTLTJ 10FILTRATION RATE FILTRATION RATE A MEASUREMENT OF THE RATE OF FILTRATION. 2D AND 1B MODE REPLY22AG671AC20 BTLWG 09MATERIAL,DESICCANT DESICCANT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE DESICCANT IS FABRICATED. FULL TEXT WRITE-IN 0 BTLXD /D/ 09MATERIAL,RESILIENT RESILIENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE RESILIENT MATERIAL IS FABRICATED. SELECT REPLY CODE 10AD09 BTLYA 19CAPACITY,SEATING SEATING CAPACITY THE NUMBER OF SEATING PLACES PROVIDED. 1A MODE REPLY 0 BTLZD 19PORTION,UPHOLSTERED UPHOLSTERED PORTION THE PORTION OF THE ITEM WHICH IS UPHOLSTERED. SELECT REPLY CODE 10AC58 BTMBD /D/ 07ATTACHMENT,MOUNTING MOUNTING ATTACHMENT AN INDICATION OF WHETHER OR NOT A MOUNTING ATTACHMENT(S) IS INCLUDED. PLEASE USE MRC ABFF OR TMQY IN PLACE OF THIS CANCELED MRC USING REPLY MOUNTING ATTACHMENT. SELECT REPLY CODE 10AA49 BTMCD /D/ 07FEATURE,MOUNTING,FOLDING FOLDING MOUNTING FEATURE AN INDICATION OF WHETHER OR NOT A FOLDING MOUNTING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BTMDD 07ADJUSTABILITY,MOUNTING MOUNTING ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE MOUNTING IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BTMFD /D/ 07SPRINGS,CUSHION CUSHION SPRINGS AN INDICATION OF WHETHER OR NOT SELECT REPLY CODE 10AA49 BTMGD /D/ 07BAG,PNEUMATIC PNEUMATIC BAG AN INDICATION OF WHETHER OR NOT A PNEUMATIC BAG IS INCLUDED. SELECT REPLY CODE 10AA49 BTMHD /D/ 07BACKREST BACKREST AN INDICATION OF WHETHER OR NOT A BACKREST IS INCLUDED. SELECT REPLY CODE 10AA49 BTMJD /D/ 07FEATURE,CONTOURED CONTOURED FEATURE AN INDICATION OF WHETHER OR NOT A CONTOURED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BTMKD /D/ 07ARMREST ARMREST AN INDICATION OF WHETHER OR NOT AN ARMREST(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BTMLD /D/ 09MATERIAL,COVER,BACKREST BACKREST COVER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BACKREST COVER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BTMMD /D/ 09MATERIAL,PADDING,BACKREST BACKREST PADDING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BACKREST PADDING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BTMND 05DIRECTION,EJECTION EJECTION DIRECTION THE DIRECTION IN WHICH THE ITEM IS EJECTED. SELECT REPLY CODE 10AA38 BTMPD 08LOCATION,CONTROL,EJECTION EJECTION CONTROL LOCATION INDICATES THE LOCATION OF THE EJECTION CONTROL(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 BTMQD 19ACCOMMODATION,EQUIPMENT,PERSONAL PERSONAL EQUIPMENT ACCOMMODATION THE PERSONAL EQUIPMENT ACCOMMODATION(S) FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AJ77 BTMRJ 04LENGTH,MAXIMUM,ADJUSTMENT ADJUSTMENT MAXIMUM LENGTH A MEASUREMENT OF THE MAXIMUM DIMENSION THE ITEM CAN BE ADJUSTED,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BTMSD /D/ 07RELEASE,AUTOMATIC,CARTRIDGE OPERATED CARTRIDGE OPERATED AUTOMATIC RELEASE AN INDICATION OF WHETHER OR NOT A CARTRIDGE OPERATED AUTOMATIC RELEASE IS INCLUDED. SELECT REPLY CODE 10AA49 BTMTD /D/ 07ASSEMBLY,ACTUATING ACTUATING ASSEMBLY AN INDICATION OF WHETHER OR NOT AN ACTUATING ASSEMBLY IS INCLUDED. SELECT REPLY CODE 10AA49 BTMWD 18TYPE,CASE,CARTRIDGE CARTRIDGE CASE TYPE INDICATES THE TYPE OF CARTRIDGE CASE PROVIDED. SELECT REPLY CODE 10AK54 BTMXJ 04LENGTH,ASSEMBLY,CABLE CABLE ASSEMBLY LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CABLE ASSEMBLY,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BTMYD 18TYPE,REEL REEL TYPE INDICATES THE TYPE OF REEL PROVIDED. SELECT REPLY CODE 10AK37 BTMZD 08LOCATION,REEL REEL LOCATION INDICATES THE LOCATION OF THE REEL ON THE ITEM. SELECT REPLY CODE 10AJ91 BTNBD /D/ 18TYPE FOR WHICH DESIGNED,ATTACHMENT,SHOULDER HARNESS SHOULDER HARNESS ATTACHMENT TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF SHOULDER HARNESS ATTACHMENT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BTNCJ 04LENGTH ON DRUM,TRAVEL,CABLE CABLE TRAVEL LENGTH ON DRUM A MEASUREMENT OF THE LENGTH THE CABLE WILL TRAVEL ON THE DRUM 2D AND 1B MODE REPLY21AA051AC20 BTNDJ 04LENGTH,TRAVEL,ROLLER WEBBING ROLLER WEBBING TRAVEL LENGTH A MEASUREMENT OF THE LENGTH THE WEBBING WILL TRAVEL ON THE ROLLER. 2D AND 1B MODE REPLY21AA051AC20 BTNFD /D/ 07ATTACHMENT,HARNESS,SHOULDER SHOULDER HARNESS ATTACHMENT AN INDICATION OF WHETHER OR NOT A SHOULDER HARNESS ATTACHMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BTNGJ 04LENGTH,EXTENDED,ATTACHMENT,SHOULDER,HARNESS SHOULDER HARNESS ATTACHMENT EXTENDED LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SHOULDER HARNESS ATTACHMENT WHEN IT IS IN AN EXTENDED LENGTH. 2D AND 1B MODE REPLY21AA051AC20 BTNHD /D/ 18TYPE,CONTROL,MANUAL LOCK MANUAL LOCK CONTROL TYPE INDICATES THE TYPE OF MANUAL LOCK CONTROL. SELECT REPLY CODE 10AK54 BTNJJ 04DISTANCE FROM REEL TO CONTROL HANDLE SHAFT,CENTER TO CENTER CENTER TO CENTER DISTANCE FROM REEL TO CONTROL HANDLE SHAFT THE DISTANCE FROM THE REEL CENTERLINE TO THE CENTER OF THE CONTROL HANDLE SHAFT. 2D AND 1B MODE REPLY21AA051AC20 BTNKD /D/ 07CONTROL,OPERATED,ELECTRICALLY ELECTRICALLY OPERATED CONTROL AN INDICATION OF WHETHER OR NOT AN ELECTRICALLY OPERATED CONTROL(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BTNLD /D/ 07CONNECTOR,ELECTRICAL ELECTRICAL CONNECTOR AN INDICATION OF WHETHER OR NOT AN ELECTRICAL CONNECTOR(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BTNNA 12QUANTITY,COLLET,EXPANDING EXPANDING COLLET QUANTITY THE NUMBER OF EXPANDING COLLETS PROVIDED. 1A MODE REPLY 0 BTNPA 12QUANTITY,TAP,ENGAGING ENGAGING TAP QUANTITY THE NUMBER OF ENGAGING TAPS PROVIDED. 1A MODE REPLY 0 BTNQA 12QUANTITY,BUSHING,ENGAGING ENGAGING BUSHING QUANTITY THE NUMBER OF ENGAGING BUSHINGS PROVIDED. 1A MODE REPLY 0 BTNRA 12QUANTITY,PLATE,INSTALLING INSTALLING PLATE QUANTITY THE NUMBER OF INSTALLING PLATES PROVIDED. 1A MODE REPLY 0 BTNSA 12QUANTITY,PLATE,ADAPTER ADAPTER PLATE QUANTITY THE NUMBER OF ADAPTER PLATES PROVIDED. 1A MODE REPLY 0 BTNTA 12QUANTITY,ARBOR,EXPANDING EXPANDING ARBOR QUANTITY THE NUMBER OF EXPANDING ARBORS PROVIDED. 1A MODE REPLY 0 BTNWG 04SIZE FOR WHICH DESIGNED,HOLE,ANVIL ANVIL HOLE SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE ANVIL HOLE FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 BTNYJ 04HEIGHT,POST POST HEIGHT A MEASUREMENT OF A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF A POST,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BTNZD 18TYPE FOR WHICH DESIGNED,VALVE VALVE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF VALVE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL80 BTPBJ 04HEIGHT,END,RECTANGULAR RECTANGULAR END HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BTPCJ 04WIDTH,END,RECTANGULAR RECTANGULAR END WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTPFA /D/ 16STYLE DESIGNATOR,TOOL TOOL STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TOOL(S). 1A MODE REPLY 0 BTPGJ 04DEPTH,BOWL BOWL DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE BOWL,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BTPHA 12QUANTITY,LIP LIP QUANTITY THE NUMBER OF LIPS PROVIDED. 1A MODE REPLY 0 BTPJD /D/ 07HANDLE,SLEEVE,SLIDING SLIDING SLEEVE HANDLE AN INDICATION OF WHETHER OR NOT A SLIDING SLEEVE HANDLE IS PROVIDED. SELECT REPLY CODE 10AB22 BTPKD /D/ 07FEATURE,SELF-SKIMMING SELF-SKIMMING FEATURE AN INDICATION OF WHETHER OR NOT A SELF-SKIMMING FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BTPLL /D/ 16STYLE,TOOL,HAND HAND TOOL STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HAND TOOL/S/. 1L MODE REPLY 0 BTPMD /D/ 09MATERIAL FOR WHICH DESIGNED MATERIAL FOR WHICH DESIGNED THE MATERIAL FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AD09 BTPND /D/ 07LIP LIP AN INDICATION OF WHETHER OR NOT A LIP IS PROVIDED. SELECT REPLY CODE 10AB22 BTPPD 18TYPE ACCOMMODATED,GLUE GLUE TYPE ACCOMMODATED INDICATES THE TYPE OF GLUE THE ITEM WILL ACCOMMODATE. SELECT REPLY CODE 10AK54 BTPQD 08LOCATION,ELEMENT,HEATING HEATING ELEMENT LOCATION INDICATES THE LOCATION OF THE HEATING ELEMENT(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 BTPRD 07ADJUSTABILITY,CONTROL,THERMOSTAT THERMOSTAT CONTROL ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE THERMOSTAT CONTROL IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BTPSD /D/ 07LADLE LADLE AN INDICATION OF WHETHER OR NOT A LADLE IS PROVIDED. SELECT REPLY CODE 10AB22 BTPTD /D/ 18TYPE FOR WHICH DESIGNED,HEAD HEAD TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF HEAD FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AE98 BTPWG /D/ 04SIZE FOR WHICH DESIGNED,RIVET RIVET SIZE FOR WHICH DESIGNED DESIGNATES THE COMMERCIAL SIZE OR DIAMETER OF THE RIVET FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 BTPXG 19CHARACTERISTICS AND QUANTITY,HEAD,PULLING PULLING HEAD CHARACTERISTICS AND QUANTITY THE PULLING HEAD CHARACTERISTICS,SUCH AS THE RIVET DIAMETER,RIVET HEAD STYLE ACCOMMODATED,MANUFACTURERS TYPE,AND THE NUMBER OF EACH PROVIDED. FULL TEXT WRITE-IN 0 BTPYG /D/ 19CHARACTERISTICS,TEMPLATE TEMPLATE CHARACTERISTICS AN INDICATION OF THE TEMPLATE CHARACTERISTICS OF THE ITEM. FULL TEXT WRITE-IN 0 BTPZD /D/ 07PROVISION,SCREW,LEFT-HAND LEFT-HAND SCREW PROVISION AN INDICATION OF WHETHER OR NOT A PROVISION FOR A LEFT-HAND SCREW/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BTQBD /D/ 07NUT,TURNOUT,SLIDING SLIDING TURNOUT NUT AN INDICATION OF WHETHER OR NOT A SLIDING TURNOUT NUT IS INCLUDED. SELECT REPLY CODE 10AA49 BTQCD /D/ 07GUIDE,DRILL DRILL GUIDE AN INDICATION OF WHETHER OR NOT A DRILL GUIDE IS INCLUDED. SELECT REPLY CODE 10AA49 BTQDD /D/ 07DRILL DRILL AN INDICATION OF WHETHER OR NOT A DRILL IS INCLUDED. SELECT REPLY CODE 10AA49 BTQFJ 10SIZE,SCREW SCREW SIZE DESIGNATES THE SIZE OF THE SCREW. 2D AND 1B MODE REPLY21AA051AC20 BTQGJ 10SIZE,PIPE PIPE SIZE DESIGNATES THE SIZE OF THE PIPE. 2D AND 1B MODE REPLY21AA051AC20 BTQHA /D/ 04SIZE ACCOMMODATED,CUTTING,DIE DIE CUTTING SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE CUTTING DIE(S) THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 BTQJG 04SIZE,DRIVE DRIVE SIZE DESIGNATES THE SIZE OF THE DRIVE. FULL TEXT WRITE-IN 0 BTQKJ 10SIZE FOR WHICH DESIGNED,TAP TAP SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE TAP FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 BTQLJ /D/T04SIZE RANGE ACCOMMODATED,CUTTING,DIE DIE CUTTING SIZE RANGE ACCOMMODATED DESIGNATES THE SIZE RANGE OF THE CUTTING DIE(S) THE ITEM WILL ACCOMMODATE. 1D AND 1F MODE REPLY11AA05 BTQMD /D/ 07SHOE SHOE AN INDICATION OF WHETHER OR NOT A SHOE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BTQNJ 04WIDTH FOR WHICH DESIGNED,FRAME FRAME WIDTH FOR WHICH DESIGNED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FRAME FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BTQPJ 10UNDERCLEARANCE,MAXIMUM MAXIMUM UNDERCLEARANCE THE MAXIMUM DISTANCE BETWEEN THE GROUND SURFACE AND THE BOTTOM OF THE ITEM. 1D AND 1B MODE REPLY11AA05 BTQQJ /D/ 04LENGTH FROM TOP OF HEAD TO RADIUS CENTER LENGTH FROM TOP OF HEAD TO RADIUS CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 BTQRJ 04RADIUS,HEAD HEAD RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BTQSJ 04LENGTH,RECESS,LOCKING LOCKING RECESS LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTQTJ 04LENGTH,RECESS,LOWER LOCKING LOWER LOCKING RECESS LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTQWJ /D/ 04DEPTH,SHANK SHANK DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTQXJ 04DIAMETER,OUTSIDE,LOWER LOCKING RECESS LOWER LOCKING RECESS OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BTQYD 19AGENT FOR WHICH DESIGNED,EXTINGUISHING EXTINGUISHING AGENT FOR WHICH DESIGNED AN INDICATION OF THE EXTINGUISHING AGENT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AG54 BTQZA 12QUANTITY,TANK,WATER WATER TANK QUANTITY THE NUMBER OF WATER TANKS PROVIDED. 1A MODE REPLY 0 BTRBA 12QUANTITY,TANK,CHEMICAL CHEMICAL TANK QUANTITY THE NUMBER OF CHEMICAL TANKS PROVIDED. 1A MODE REPLY 0 BTRCJ 10CAPACITY,TANK,CHEMICAL CHEMICAL TANK CAPACITY THE AMOUNT OF CHEMICALS THE TANK WILL HOLD. 1D AND 1B MODE REPLY12AG67 BTRDD /D/ 07LADDER,AERIAL AERIAL LADDER AN INDICATION OF WHETHER OR NOT AN AERIAL LADDER/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BTRFD 03DESIGNATION,SIZE,CHASSIS CHASSIS SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE CHASSIS IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. SELECT REPLY CODE 10AA27 BTRGD /D/ 07FEATURE,DRIVE,FRONT WHEEL FRONT WHEEL DRIVE FEATURE AN INDICATION OF WHETHER OR NOT A FRONT WHEEL DRIVE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BTRHJ 10LOAD RATING,CHASSIS CHASSIS LOAD RATING THE MAXIMUM RATED LOAD THE CHASSIS IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY12AG67 BTRJJ 04SIZE,WHEELBASE WHEELBASE SIZE DESIGNATES THE SIZE OF THE WHEELBASE BETWEEN THE FRONT AND REAR AXLES. 1D AND 1B MODE REPLY11AA05 BTRKD 08LOCATION,CAB CAB LOCATION INDICATES THE LOCATION OF THE CAB ON THE CHASSIS. SELECT REPLY CODE 10AJ91 BTRLD 02DESIGN,CAB CAB DESIGN THE DESIGN OF THE CAB. SELECT REPLY CODE 10AK54 BTRMJ T10RANGE,WEIGHT,GROSS GROSS WEIGHT RANGE THE GROSS WEIGHT MINIMUM TO MAXIMUM LIMITS OF THE ITEM. 1D AND 1F MODE REPLY12AG67 BTRND /D/ 07WINCH WINCH AN INDICATION OF WHETHER OR NOT A WINCH IS INCLUDED. SELECT REPLY CODE 10AA49 BTRPD 11METHOD,DISCHARGE,EXTINGUISHING AGENT EXTINGUISHING AGENT DISCHARGE METHOD THE MEANS BY WHICH THE EXTINGUISHING AGENT IS DISCHARGED. SELECT REPLY CODE 10AL88 BTRQD 18TYPE,CYLINDER CYLINDER TYPE INDICATES THE TYPE OF CYLINDER PROVIDED. SELECT REPLY CODE 10AA78 BTRRD /D/ 07FEATURE,SPLASHPROOF SPLASHPROOF FEATURE AN INDICATION OF WHETHER OR NOT A SPLASHPROOF FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BTRSD /D/ 17SURFACE TREATMENT,CONTAINER CONTAINER SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE CONTAINER. SELECT REPLY CODE 10AD09 BTRTD /D/ 07FEATURE,DEMOUNTABLE/NESTABLE DEMOUNTABLE/NESTABLE FEATURE AN INDICATION OF WHETHER OR NOT A DEMOUNTABLE AND NESTABLE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BTRWA 04SIZE FOR WHICH DESIGNED,EXTINGUISHER EXTINGUISHER SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE EXTINGUISHER FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 BTRXD 18TYPE,CYLINDER,GAS GAS CYLINDER TYPE INDICATES THE TYPE OF GAS CYLINDER PROVIDED. SELECT REPLY CODE 10AB75 BTRYA /D/ 16STYLE DESIGNATOR,BRACKET BRACKET STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BRACKET. 1A MODE REPLY 0 BTRZD /D/ 18TYPE ACCOMMODATED,HOSE HOSE TYPE ACCOMMODATED INDICATES THE TYPE OF HOSE THE ITEM WILL ACCOMMODATE. SELECT REPLY CODE 10AJ58 BTSBD /D/ 07STRAP,RETAINING,HINGED HOSE HINGED HOSE RETAINING STRAP AN INDICATION OF WHETHER OR NOT A HINGED HOSE RETAINING STRAP(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BTSCJ /D/ 04DIAMETER,CLAMP,PIPE PIPE CLAMP DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PIPE CLAMP,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BTSDJ 04DISTANCE BETWEEN SIDES DISTANCE BETWEEN SIDES THE DISTANCE BETWEEN THE SIDES OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BTSFJ /D/ 04DIAMETER,THREAD,END END THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE END THREADED PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BTSGD /D/ 18TYPE,FACILITY,WRENCHING,THREADED END THREADED END WRENCHING FACILITY TYPE INDICATES THE TYPE OF WRENCHING FACILITY USED TO ASSEMBLE OR DISASSEMBLE THE THREADED END OF AN ITEM. SELECT REPLY CODE 10AL17 BTSHD /D/ 07FEATURE,SWIVEL,THREADED END THREADED END SWIVEL FEATURE AN INDICATION OF WHETHER OR NOT THE THREADED END INCLUDES A SWIVEL FEATURE. SELECT REPLY CODE 10AA49 BTSJJ /D/ 13THREAD QUANTITY,END END THREAD QUANTITY THE NUMBER OF THREADS ON THE END OF THE ITEM,MEASURED ON A LINE PARALLEL TO THE THREAD AXIS. 1D AND 1B MODE REPLY11AB39 BTSKD /D/ 07FIXTURE,MOUNTING,GROUND GROUND MOUNTING FIXTURE AN INDICATION OF WHETHER OR NOT A GROUND MOUNTING FIXTURE IS INCLUDED. SELECT REPLY CODE 10AA49 BTSLD /D/ 07TIP TIP AN INDICATION OF WHETHER OR NOT A TIP(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BTSMJ 04THREAD DIAMETER,END,PLAY PIPE DISCHARGE PLAY PIPE DISCHARGE END THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PLAY PIPE DISCHARGE END THREADED PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BTSNG /D/ 13THREAD SIZE DESIGNATOR,BORE BORE THREAD SIZE DESIGNATOR NONE. FULL TEXT WRITE-IN 0 BTSPJ /D/ 04DIAMETER,BORE,UNTHREADED UNTHREADED BORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BTSQJ /D/ 04DEPTH,BORE,UNTHREADED UNTHREADED BORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTSRJ /D/ 04DIAMETER,COUNTERBORE,POSITIONING HOLE POSITIONING HOLE COUNTERBORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BTSSJ /D/ 04DEPTH,COUNTERBORE,HOLE,POSITIONING POSITIONING HOLE COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTSTJ /D/ 04DIAMETER,HOLE,RECESSED RECESSED HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BTSWJ /D/ 04DEPTH,HOLE,RECESSED RECESSED HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BTSXJ 04DIAMETER ACCOMMODATED,BAR STOCK,MAXIMUM MAXIMUM BAR STOCK DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BAR STOCK ACCOMMODATED,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BTSYJ 04DISTANCE OVER UNIVERSAL CARRIAGE,CHUCKING,MAXIMUM MAXIMUM CHUCKING DISTANCE OVER UNIVERSAL CARRIAGE THE MAXIMUM DISTANCE OF THE CHUCK OVER THE UNIVERSAL CARRIAGE. 1D AND 1B MODE REPLY11AA05 BTSZA 12QUANTITY,SPEED,SPINDLE SPINDLE SPEED QUANTITY THE NUMBER OF SPINDLE SPEEDS PROVIDED. 1A MODE REPLY 0 BTTBF T10RANGE IN RPM,SPEED,SPINDLE SPINDLE SPEED RANGE IN RPM THE MINIMUM TO MAXIMUM SPEED LIMITS OF THE SPINDLE,EXPRESSED IN REVOLUTIONS PER MINUTE. 1F MODE REPLY 0 BTTCD 07REVERSIBILITY,SPINDLE SPINDLE REVERSIBILITY AN INDICATION OF WHETHER OR NOT THE SPINDLE IS REVERSIBLE. SELECT REPLY CODE 10AF62 BTTDJ 10SWING,RATED RATED SWING A MEASUREMENT OF THE RATED SWING OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BTTFJ 10SWING OVER BED,ACTUAL ACTUAL SWING OVER BED A MEASUREMENT OF THE ACTUAL SWING OVER THE BED OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BTTGJ 10SWING OVER CROSS SLIDE SWING OVER CROSS SLIDE A MEASUREMENT OF THE SWING OVER THE CROSS SLIDE OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BTTHJ 04DISTANCE FROM SPINDLE NOSE TO TURRET FACE,MAXIMUM MAXIMUM DISTANCE FROM SPINDLE NOSE TO TURRET FACE THE MAXIMUM DISTANCE FROM THE SPINDLE NOSE TO THE TURRET FACE. 1D AND 1B MODE REPLY11AA05 BTTJJ 10TRAVEL,LONGITUDINAL,UNIVERSAL CARRIAGE UNIVERSAL CARRIAGE LONGITUDINAL TRAVEL THE DISTANCE THE UNIVERSAL CARRIAGE IS DESIGNED TO TRAVEL LONGITUDINALLY. 2D AND 1B MODE REPLY21AA051AC20 BTTKJ 10TRAVEL,CROSS,UNIVERSAL CARRIAGE UNIVERSAL CARRIAGE CROSS TRAVEL THE DISTANCE THE UNIVERSAL CARRIAGE IS DESIGNED FOR CROSS TRAVEL. 2D AND 1B MODE REPLY21AA051AC20 BTTLD 18TYPE,FEED,UNIVERSAL CARRIAGE UNIVERSAL CARRIAGE FEED TYPE INDICATES THE TYPE OF FEED PROVIDED ON THE UNIVERSAL CARRIAGE. SELECT REPLY CODE 10AK97 BTTMJ T10RANGE PER SPINDLE REVOLUTION,FEED,LONGITUDINAL LONGITUDINAL FEED RANGE PER SPINDLE REVOLUTION THE LONGITUDINAL FEED RANGE OF THE ITEM,PER SPINDLE REVOLUTION. 1D AND 1F MODE REPLY11AA05 BTTNJ T10RANGE PER SPINDLE REVOLUTION,FEED,CROSS CROSS FEED RANGE PER SPINDLE REVOLUTION THE CROSS FEED RANGE OF THE ITEM,PER SPINDLE REVOLUTION. 1D AND 1F MODE REPLY11AA05 BTTPD /D/ 07COMPOUND,CARRIAGE,UNIVERSAL UNIVERSAL CARRIAGE COMPOUND AN INDICATION OF WHETHER OR NOT A UNIVERSAL CARRIAGE COMPOUND IS INCLUDED. SELECT REPLY CODE 10AA49 BTTQB 10TRAVEL IN DEG,ROTATION ROTATION TRAVEL IN DEG THE DEGREE OF ROTATION AT WHICH THE ITEM IS DESIGNED TO TRAVEL. 1B MODE REPLY 0 BTTRJ 10TRAVEL,LONGITUDINAL,TURRET CARRIAGE TURRET CARRIAGE LONGITUDINAL TRAVEL THE DISTANCE THE TURRET CARRIAGE IS DESIGNED TO TRAVEL LONGITUDINALLY. 2D AND 1B MODE REPLY21AA051AC20 BTTSJ 10TRAVEL,CROSS,TURRET CARRIAGE TURRET CARRIAGE CROSS TRAVEL THE DISTANCE THE TURRET CARRIAGE IS DESIGNED TO CROSS TRAVEL. 2D AND 1B MODE REPLY21AA051AC20 BTTTD 18TYPE,FEED,TURRET CARRIAGE TURRET CARRIAGE FEED TYPE INDICATES THE TYPE OF FEED PROVIDED FOR THE TURRET CARRIAGE. SELECT REPLY CODE 10AK97 BTTWF /D/T10RANGE PER SPINDLE REVOLUTION,FEED,LONGITUDINAL,TURRET CARRIAGE TURRET CARRIAGE LONGITUDINAL FEED RANGE PER SPINDLE REVOLUTION THE LONGITUDINAL FEED RANGE OF THE TURRET CARRIAGE,PER SPINDLE REVOLUTION. 1F MODE REPLY 0 BTTXF /D/T10RANGE PER SPINDLE REVOLUTION,FEED,CROSS,TURRET CARRIAGE TURRET CARRIAGE CROSS FEED RANGE PER SPINDLE REVOLUTION THE CROSS FEED RANGE OF THE TURRET CARRIAGE,PER SPINDLE REVOLUTION. 1F MODE REPLY 0 BTTYD 14SHAPE,TURRET TURRET SHAPE THE PHYSICAL CONFIGURATION OF THE TURRET. SELECT REPLY CODE 10AD07 BTTZA 12QUANTITY,POSITION,TURRET TURRET POSITION QUANTITY THE NUMBER OF TURRET POSITIONS PROVIDED. 1A MODE REPLY 0 BTWAJ 10PRESSURE,AIR AIR PRESSURE THE AMOUNT OF AIR PRESSURE REQUIRED FOR OPERATION. 2D AND 1B MODE REPLY22AG671AC20 BTWBA 12QUANTITY,THREAD CHANGE THREAD CHANGE QUANTITY THE NUMBER OF THREAD CHANGES PROVIDED. 1A MODE REPLY 0 BTWCJ 10SWING THROUGH OPEN GAP,RATED RATED SWING THROUGH OPEN GAP A MEASUREMENT OF THE RATED SWING THROUGH THE OPEN GAP. 2D AND 1B MODE REPLY21AA051AC20 BTWDJ 10SWING THROUGH OPEN GAP,ACTUAL ACTUAL SWING THROUGH OPEN GAP A MEASUREMENT OF THE ACTUAL SWING THROUGH THE OPEN GAP. 2D AND 1B MODE REPLY21AA051AC20 BTWFJ 10SWING OVER CLOSED GAP,RATED RATED SWING OVER CLOSED GAP A MEASUREMENT OF THE RATED SWING OVER THE CLOSED GAP. 2D AND 1B MODE REPLY21AA051AC20 BTWGJ 10SWING OVER CLOSED GAP,ACTUAL ACTUAL SWING OVER CLOSED GAP A MEASUREMENT OF THE ACTUAL SWING OVER THE CLOSED GAP. 2D AND 1B MODE REPLY21AA051AC20 BTWJJ 04DISTANCE BETWEEN OPEN CENTERS DISTANCE BETWEEN OPEN CENTERS THE CENTER TO CENTER DISTANCE OF THE ITEM WHEN OPEN. 2D AND 1B MODE REPLY21AA051AC20 BTWKJ 04DISTANCE BETWEEN CLOSED CENTERS DISTANCE BETWEEN CLOSED CENTERS THE CENTER TO CENTER DISTANCE OF THE ITEM WHEN CLOSED. 2D AND 1B MODE REPLY21AA051AC20 BTWLD 18TYPE,DRIVE,HEADSTOCK HEADSTOCK DRIVE TYPE INDICATES THE TYPE OF HEADSTOCK DRIVE PROVIDED FOR TURNING,ROTATING,OR POSITIONING THE MECHANISM. SELECT REPLY CODE 10AG25 BTWMJ /D/A03DESIGNATOR,SIZE,HEADSTOCK CENTER TAPER HEADSTOCK CENTER TAPER SIZE DESIGNATOR THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE HEADSTOCK CENTER TAPER SIZE. 1D AND 1A MODE REPLY12AH09 BTWNG /D/ 04SIZE ACCOMMODATED,MATERIAL,GUIDE GUIDE MATERIAL SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE MATERIAL THE GUIDE WILL ACCOMMODATE. FULL TEXT WRITE-IN 0 BTWPD 14SHAPE FOR WHICH DESIGNED,DIE DIE SHAPE FOR WHICH DESIGNED THE PHYSICAL CONFIGURATION OF THE DIE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AD07 BTWQJ 04DIAMETER ACCOMMODATED,DIE DIE DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR A DIE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BTWRJ 04WIDTH ACCOMMODATED,DIE DIE WIDTH ACCOMMODATED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE DIE THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BTWSJ 04THICKNESS,ACCOMMODATED,DIE DIE THICKNESS ACCOMMODATED A MEASUREMENT OF THE SMALLEST DIMENSION OF THE DIE THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BTWTD 07ADJUSTABILITY,GUIDE GUIDE ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE GUIDE IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BTWWD /D/ 07BUSHING,GUIDE GUIDE BUSHING AN INDICATION OF WHETHER OR NOT A GUIDE BUSHING IS PROVIDED. SELECT REPLY CODE 10AB22 BTWXD /D/ 09MATERIAL,TAP TAP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH A TAP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BTWYG 19CHARACTERISTIC,TAP TAP CHARACTERISTIC AN INDICATION OF THE TAP CHARACTERISTIC(S) OF THE ITEM. FULL TEXT WRITE-IN 0 BTWZG /D/ 19NUMBER AND QUANTITY,STOCK,TAP WRENCH TAP WRENCH STOCK NUMBER AND QUANTITY AN INDICATION OF THE STOCK NUMBER AND NUMBER OF TAP WRENCHES PROVIDED. FULL TEXT WRITE-IN 0 BTXAJ /D/ 10PRESSURE,WATER WATER PRESSURE THE AMOUNT OF WATER PRESSURE REQUIRED FOR OPERATION. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 2D AND 1B MODE REPLY22AG671AC20 BTXBG 19CHARACTERISTIC,TOOL,COUNTERBORE COUNTERBORE TOOL CHARACTERISTIC AN INDICATION OF THE COUNTERBORE TOOL CHARACTERISTICS. FULL TEXT WRITE-IN 0 BTXCD 18TYPE,TOOTH,FLEXIBLE BACK FLEXIBLE BACK TOOTH TYPE INDICATES THE TYPE OF FLEXIBLE BACK TEETH PROVIDED. SELECT REPLY CODE 10AL23 BTXDD /D/ 18TYPE,SET,TOOTH TOOTH SET TYPE INDICATES THE TYPE OF TOOTH SET PROVIDED. SELECT REPLY CODE 10AK54 BTXFJ 04LENGTH,COILED COILED LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ITEM WHEN COILED,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BTXGJ 04LENGTH,JOINED JOINED LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ITEM WHEN JOINED,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BTXHG /D/ 19PITCH,TOOTH TOOTH PITCH AN INDICATION OF THE PITCH OF THE TOOTH. FULL TEXT WRITE-IN 0 BTXJD 18TYPE,EDGE,TOOTH TOOTH EDGE TYPE INDICATES THE TYPE OF TOOTH EDGE PROVIDED. SELECT REPLY CODE 10AL25 BTXKA 19NUMBER,GAGE,RIM RIM GAGE NUMBER THE GAGE DESIGNATION USED TO INDICATE THE NUMBER OF THE RIM. 1A MODE REPLY 0 BTXLJ 04THICKNESS,RIM RIM THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE RIM,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BTXMA /D/ 16STYLE,TOOTH,SOLID SOLID TOOTH STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SOLID TOOTH. 1A MODE REPLY 0 BTXNG 19NAME/SPEC TITLE,MANUFACTURER MANUFACTURER NAME/SPEC TITLE THE MANUFACTURER NAME AND/OR SPECIFICATION TITLE USED TO IDENTIFY THE ITEM. FULL TEXT WRITE-IN 0 BTXPG 18TYPE DESIGNATOR,MANUFACTURER MANUFACTURER TYPE DESIGNATOR THE MANUFACTURER IDENTIFYING TYPE DESIGNATION ASSIGNED TO THE ITEM. FULL TEXT WRITE-IN 0 BTXQA /D/ 12QUANTITY,PINHOLE PINHOLE QUANTITY THE NUMBER OF PINHOLES PROVIDED. 1A MODE REPLY 0 BTXRB 04ANGLE FROM SAW IN DEG,TILT,LEFT,TABLE TABLE LEFT TILT ANGLE FROM SAW IN DEG THE LEFT TILT ANGLE OF THE TABLE FROM THE SAW,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BTXSJ 04DIAMETER,CIRCLE,PINHOLE PINHOLE CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PINHOLE CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BTXTJ /D/ 04DIAMETER,OUTSIDE,BLADE BLADE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BLADE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BTXWG /D/ 19NUMBER FOR WHICH DESIGNED,MANUFACTURER/SPEC,ARBOR ARBOR MANUFACTURER/SPEC NUMBER FOR WHICH DESIGNED THE MANUFACTURER AND/OR SPECIFICATION NUMBER USED TO IDENTIFY THE ARBOR /MANDREL/ FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 BTXXJ A12QUANTITY,POINT POINT QUANTITY THE NUMBER OF POINTS ON THE ITEM. 1D AND 1A MODE REPLY11AB39 BTXYD 18TYPE,END,BUTT BUTT END TYPE INDICATES THE TYPE OF BUTT END PROVIDED. SELECT REPLY CODE 10AK84 BTXZD /D/ 19PATTERN,TOOTH TOOTH PATTERN AN INDICATION OF THE PATTERN OF THE TEETH. SELECT REPLY CODE 10AK18 BTYBD /D/ 03DESIGNATION,PATTERN,TOOTH TOOTH PATTERN DESIGNATION AN INDICATION OF THE TOOTH PATTERN DESIGNATION OF THE ITEM. SELECT REPLY CODE 10AE92 BTYCJ /D/ 04WIDTH,CENTER CENTER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CENTER OF THE ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BTYDD /D/ 07FEATURE,WIDTH,UNIFORM UNIFORM WIDTH FEATURE AN INDICATION OF WHETHER OR NOT A UNIFORM WIDTH FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BTYFJ /D/ 04THICKNESS,EDGE,CUTTING CUTTING EDGE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE CUTTING EDGE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BTYGD /D/ 07TAPER,ENDS TO CENTER,BLADE BACK BLADE BACK ENDS TO CENTER TAPER AN INDICATION OF WHETHER OR NOT A TAPER FROM THE ENDS TO THE CENTER OF THE BLADE BACK IS PROVIDED. SELECT REPLY CODE 10AB22 BTYHD 14SHAPE,BACK BACK SHAPE THE PHYSICAL CONFIGURATION OF THE BACK OF THE ITEM. SELECT REPLY CODE 10AD07 BTYJJ 04WIDTH,BUTT,BLADE BLADE BUTT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BLADE AT THE BUTT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BTYKJ 04WIDTH,POINT,BLADE BLADE POINT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BLADE AT THE POINT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BTYLD 18TYPE,ARBOR ARBOR TYPE INDICATES THE TYPE OF ARBOR PROVIDED. SELECT REPLY CODE 10AK54 BTYMD /D/ 07SPRING,EJECTOR,ARBOR ARBOR EJECTOR SPRING AN INDICATION OF WHETHER OR NOT AN ARBOR EJECTOR SPRING IS PROVIDED. SELECT REPLY CODE 10AB22 BTYNJ 10SIZE,HOLE,HOLLOW SPINDLE HOLLOW SPINDLE HOLE SIZE DESIGNATES THE SIZE OF THE HOLLOW SPINDLE HOLE. 2D AND 1B MODE REPLY21AA051AC20 BTYPJ 04DIAMETER THROUGH SPINDLE,HOLE HOLE DIAMETER THROUGH SPINDLE THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THROUGH HOLE OF A SPINDLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BTYQA 12QUANTITY,CARRIAGE CARRIAGE QUANTITY THE NUMBER OF CARRIAGES PROVIDED. 1A MODE REPLY 0 BTYRD 11METHOD,OPERATION,CARRIAGE LONGITUDINAL FEED CARRIAGE LONGITUDINAL FEED OPERATION METHOD THE MEANS USED TO OPERATE THE CARRIAGE LONGITUDINAL FEED. SELECT REPLY CODE 10AJ28 BTYSD 11METHOD,OPERATION,CARRIAGE CROSS FEED CARRIAGE CROSS FEED OPERATION METHOD THE MEANS USED TO OPERATE THE CARRIAGE CROSS FEED. SELECT REPLY CODE 10AJ28 BTYTA 12QUANTITY,CHANGE,CARRIAGE FEED CARRIAGE FEED CHANGE QUANTITY THE NUMBER OF CARRIAGE FEED CHANGES PROVIDED. 1A MODE REPLY 0 BTYWD /D/ 18TYPE,CHANGE,GEAR GEAR CHANGE TYPE INDICATES THE TYPE OF GEAR CHANGE PROVIDED. SELECT REPLY CODE 10AK54 BTYXJ 04DIAMETER ACCOMMODATED,DRUM,MAXIMUM MAXIMUM DRUM DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE DRUM,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BTYYJ 04DIAMETER ACCOMMODATED,DRUM,MINIMUM MINIMUM DRUM DIAMETER ACCOMMODATED THE MINIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION OF THE DRUM,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BTYZD 18TYPE,TOOL,CUTTING CUTTING TOOL TYPE INDICATES THE TYPE OF CUTTING TOOL PROVIDED. SELECT REPLY CODE 10AJ57 BTZBD /D/ 07PROVISION,GRINDING GRINDING PROVISION AN INDICATION OF WHETHER OR NOT A GRINDING PROVISION IS INCLUDED. SELECT REPLY CODE 10AA49 BTZCJ 10TRAVEL,VERTICAL,TABLE TABLE VERTICAL TRAVEL THE MEASURED DISTANCE THE TABLE IS DESIGNED TO TRAVEL VERTICALLY. 2D AND 1B MODE REPLY21AA051AC20 BTZDJ 05DIRECTION AND ADJUSTMENT IN DEG,SWIVEL,TABLE TABLE SWIVEL DIRECTION AND ADJUSTMENT IN DEG THE SWIVEL DIRECTION AND ADJUSTMENT OF THE TABLE,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY13AM84 BTZFJ 10ADJUSTMENT,SPINDLE SPINDLE ADJUSTMENT A MEASUREMENT OF THE SPINDLE ADJUSTMENT. 2D AND 1B MODE REPLY21AA051AC20 BTZGJ 10ADJUSTMENT,CROSS,SPINDLE SPINDLE CROSS ADJUSTMENT A MEASUREMENT OF THE SPINDLE CROSS ADJUSTMENT. 2D AND 1B MODE REPLY21AA051AC20 BTZHJ 10ADJUSTMENT,CROSS,RAM RAM CROSS ADJUSTMENT A MEASUREMENT OF THE RAM CROSS ADJUSTMENT. 2D AND 1B MODE REPLY21AA051AC20 BTZJJ 04DISTANCE FROM SPINDLE CENTER TO TABLE TOP,MAXIMUM MAXIMUM DISTANCE FROM SPINDLE CENTER TO TABLE TOP THE MAXIMUM DISTANCE FROM SPINDLE CENTER TO TABLE TOP. 1D AND 1B MODE REPLY11AA05 BTZKJ 04DISTANCE FROM SPINDLE NOSE TO WORKING SURFACE,MAXIMUM MAXIMUM DISTANCE FROM SPINDLE NOSE TO WORKING SURFACE THE MAXIMUM DISTANCE FROM SPINDLE NOSE TO WORKING SURFACE. 1D AND 1B MODE REPLY11AA05 BTZLJ 10ADJUSTMENT,HEAD HEAD ADJUSTMENT A MEASUREMENT OF THE HEAD ADJUSTMENT. 2D AND 1B MODE REPLY21AA051AC20 BTZMD /D/ 07FEATURE,RESISTANT,FUNGUS,ELECTRIC MOTOR ELECTRIC MOTOR FUNGUS RESISTANT FEATURE AN INDICATION OF WHETHER OR NOT A FUNGUS RESISTANT FEATURE IS PROVIDED FOR THE ELECTRIC MOTOR. SELECT REPLY CODE 10AB22 BTZNJ 10SWING OVER GAP,RATED RATED SWING OVER GAP A MEASUREMENT OF THE RATED SWING OVER GAP. 2D AND 1B MODE REPLY21AA051AC20 BTZPJ 10SWING OVER BED,RATED RATED SWING OVER BED A MEASUREMENT OF THE RATED SWING OVER BED. 2D AND 1B MODE REPLY21AA051AC20 BTZQJ 04WIDTH,GAP GAP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE GAP,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BTZRJ T13THREAD QUANTITY RANGE THREAD QUANTITY RANGE THE MINIMUM AND MAXIMUM NUMBER OF THREADS PROVIDED ON THE ITEM. 1D AND 1F MODE REPLY11AB39 BTZSD /D/ 07SUPPRESSION,INTERFERENCE,RADIO,ELECTRIC MOTOR ELECTRIC MOTOR RADIO INTERFERENCE SUPPRESSION AN INDICATION OF WHETHER OR NOT RADIO INTERFERENCE SUPPRESSION FOR AN ELECTRIC MOTOR IS INCLUDED. SELECT REPLY CODE 10AA49 BTZTJ /D/ 04WIDTH,MAXIMUM,SLIDING GAP SLIDING GAP MAXIMUM WIDTH THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SLIDING GAP,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BTZWJ /D/ 19DIMENSION,BED,OPEN OPEN BED DIMENSION THE DIMENSION OF THE BED WHEN OPEN. 2D AND 1B MODE REPLY21AA051AC20 BTZXJ /D/ 19DIMENSION,BED,CLOSED CLOSED BED DIMENSION THE DIMENSION OF THE BED WHEN CLOSED. 2D AND 1B MODE REPLY21AA051AC20 BTZYJ 10SWING OVER SOLID BED,RATED RATED SWING OVER SOLID BED A MEASUREMENT OF THE RATED SWING OVER A SOLID BED. 2D AND 1B MODE REPLY21AA051AC20 BTZZJ /D/ 10SWING OVER SOLE PLATE,RATED RATED SWING OVER SOLE PLATE A MEASUREMENT OF THE RATED SWING OVER A SOLE PLATE. 2D AND 1B MODE REPLY21AA051AC20 BWACJ 04WIDTH ACCOMMODATED,BLADE BLADE WIDTH ACCOMMODATED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BLADE ACCOMMODATED, IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BWBBJ /D/A03DESIGNATOR,SIZE,HEADSTOCK SPINDLE NOSE TAPER HEADSTOCK SPINDLE NOSE TAPER SIZE DESIGNATOR THE INDUSTRIAL DESIGNATOR OR TERM USED TO DEFINE THE HEADSTOCK SPINDLE NOSE TAPER. 1D AND 1A MODE REPLY12AH09 BWBCD /D/ 07FEATURE,CENTER,DRIVE,HEADSTOCK HOLLOW SPINDLE HEADSTOCK HOLLOW SPINDLE DRIVE CENTER FEATURE AN INDICATION OF WHETHER OR NOT A HEADSTOCK HOLLOW SPINDLE DRIVE CENTER/S/ FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BWBDD /D/ 11METHOD,ATTACHMENT,HEADSTOCK FACEPLATE/CHUCK HEADSTOCK FACEPLATE/CHUCK ATTACHMENT METHOD THE MEANS BY WHICH THE HEADSTOCK FACEPLATE AND/OR CHUCK IS ATTACHED. SELECT REPLY CODE 10AB47 BWBFD 18TYPE,SUPPORT,TOOL TOOL SUPPORT TYPE INDICATES THE TYPE OF TOOL SUPPORT PROVIDED. SELECT REPLY CODE 10AM61 BWBGJ 04LENGTH ACCOMMODATED,MAXIMUM,ARMATURE ARMATURE MAXIMUM LENGTH ACCOMMODATED THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF THE ACCOMMODATION FOR THE ARMATURE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BWBHJ 04DIAMETER ACCOMMODATED,ARMATURE,MAXIMUM MAXIMUM ARMATURE DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE ARMATURE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BWBJJ 04DIAMETER ACCOMMODATED,COMMUTATOR,MAXIMUM MAXIMUM COMMUTATOR DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE COMMUTATOR,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BWBKJ 04LENGTH,MAXIMUM,CUTTING STROKE CUTTING STROKE MAXIMUM LENGTH THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF THE CUTTING STROKE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BWBLD /D/ 07ACCOMMODATION,MULTICUTTER,ADJUSTABLE SPINDLE ADJUSTABLE SPINDLE MULTICUTTER ACCOMMODATION AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE SPINDLE TO ACCOMMODATE MORE THAN ONE CUTTER IS INCLUDED. SELECT REPLY CODE 10AA49 BWBMJ 04LENGTH,STROKE,RAM RAM STROKE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE RAM STROKE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BWBNG /D/ 19SPECIFICATION,CALIBRATION CALIBRATION SPECIFICATION THE SPECIFICATION USED TO CONTROL OR REGULATE THE ACCURACY OF AN ITEM. FULL TEXT WRITE-IN 0 BWBPD /D/ 07BACKGROUND,MARKING MARKING BACKGROUND AN INDICATION OF WHETHER OR NOT A BACKGROUND FOR MARKING/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 BWBQD /D/ 18TYPE,MARKING,SCALE SCALE MARKING TYPE INDICATES THE TYPE OF SCALE MARKING(S) PROVIDED. SELECT REPLY CODE 10AM12 BWBRD /D/ 07PLATE PLATE AN INDICATION OF WHETHER OR NOT A PLATE IS PROVIDED. SELECT REPLY CODE 10AB22 BWBSA /D/ 12QUANTITY,POUR OUT POUR OUT QUANTITY THE NUMBER OF POUR OUTS PROVIDED. 1A MODE REPLY 0 BWBTA /D/ 03DESIGNATION,SIZE,NATIONAL BUREAU OF STANDARDS NATIONAL BUREAU OF STANDARDS SIZE DESIGNATION A DESIGNATION INDICATING THE NATIONAL BUREAU OF STANDARDS SIZE BY WHICH THE ITEM IS KNOWN AND/OR IDENTIFIED. 1A MODE REPLY 0 BWBWJ /D/ 04DIAMETER,OUTSIDE,MOUTH MOUTH OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MOUTH,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BWBXD /D/ 11METHOD,REINFORCEMENT,NECK NECK REINFORCEMENT METHOD THE MEANS USED TO REINFORCE THE NECK OF THE ITEM. SELECT REPLY CODE 10AE37 BWBYD /D/ 07RIM AROUND MOUTH RIM AROUND MOUTH AN INDICATION OF WHETHER OR NOT A RIM AROUND THE MOUTH IS PROVIDED. SELECT REPLY CODE 10AB22 BWBZD /D/ 07RIM,MOUTH,FLAT GROUND FLAT GROUND MOUTH RIM AN INDICATION OF WHETHER OR NOT A FLAT GROUND MOUTH RIM IS PROVIDED. SELECT REPLY CODE 10AB22 BWCBD /D/ 11METHOD,EVACUATION EVACUATION METHOD THE MEANS USED FOR EVACUATION. SELECT REPLY CODE 10AL88 BWCCD /D/ 07FUNNEL,SIDE SIDE FUNNEL AN INDICATION OF WHETHER OR NOT A SIDE FUNNEL IS PROVIDED. SELECT REPLY CODE 10AB22 BWCDA 12QUANTITY,YARN,CORE CORE YARN QUANTITY THE NUMBER OF YARNS UTILIZED TO MAKE UP THE CORE. 1A MODE REPLY 0 BWCFA 03DESIGNATION,SIZE,SINGLE PLY SINGLE PLY SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH A SINGLE PLY IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1A MODE REPLY 0 BWCGA /D/ 12QUANTITY,YARN YARN QUANTITY THE NUMBER OF YARNS UTILIZED TO MAKE UP THE ITEM. 1A MODE REPLY 0 BWCHJ /D/ 10LENGTH PER WEIGHT LENGTH PER WEIGHT A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM FOR A SPECIFIED WEIGHT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY22AG671AC20 BWCJD 18TYPE,TWIST,FINISHING FINISHING TWIST TYPE INDICATES THE TYPE OF FINISHING TWIST PROVIDED. SELECT REPLY CODE 10AG70 BWCKJ 04LENGTH PER TEN TURNS LENGTH PER TEN TURNS A MEASUREMENT OF THE LONGEST DIMENSION OF TEN TURNS. 2D AND 1B MODE REPLY21AA051AC20 BWCLJ 10WEIGHT,FORM,ISSUE ISSUE FORM WEIGHT THE WEIGHT OF THE ITEM IN ISSUE FORM. 2D AND 1B MODE REPLY22AG671AC20 BWCMD 11METHOD,RETENTION,LOOP LOOP RETENTION METHOD THE MEANS USED FOR RETAINING A LOOP. SELECT REPLY CODE 10AM39 BWCNJ 10PERIMETER,INNER,FIRST FIRST INNER PERIMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BWCPJ 10PERIMETER,INNER,SECOND SECOND INNER PERIMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BWCQJ 10PERIMETER,INNER INNER PERIMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BWCRJ A16STYLE AND LOCATION,ATTACHMENT ATTACHMENT STYLE AND LOCATION THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ATTACHMENT,AND ITS LOCATION. 1D AND 1A MODE REPLY13AJ91 BWCSH /D/ 09MATERIAL AND LOCATION,ASSEMBLY ASSEMBLY MATERIAL AND LOCATION THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH AN ASSEMBLY IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT,AND ITS LOCATION. 2D MODE REPLY 26AD093AJ91 BWCTH /D/ 17SURFACE TREATMENT AND LOCATION,ATTACHMENT ATTACHMENT SURFACE TREATMENT AND LOCATION THE PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE ATTACHMENT,AND ITS LOCATION. 2D MODE REPLY 26AD093AJ91 BWCWD /D/ 18TYPE,TUBULATURE,SIDE SIDE TUBULATURE TYPE INDICATES THE TYPE OF SIDE TUBULATOR PROVIDED. SELECT REPLY CODE 10AM35 BWCXA /D/ 12QUANTITY,RIDGE,INTERNAL LONGITUDINAL INTERNAL LONGITUDINAL RIDGE QUANTITY THE NUMBER OF INTERNAL LONGITUDINAL RIDGES ON THE ITEM. 1A MODE REPLY 0 BWCYA /D/ 19CAPACITY,SLIDE SLIDE CAPACITY THE NUMBER OF SLIDES THE ITEM CAN ACCOMMODATE. 1A MODE REPLY 0 BWCZD /D/ 07BASE,FLANGE FLANGE BASE AN INDICATION OF WHETHER OR NOT A FLANGE BASE IS PROVIDED. SELECT REPLY CODE 10AB22 BWDBD 18TYPE FOR WHICH DESIGNED,GAGE,RING RING GAGE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF RING GAGE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AJ89 BWDCJ 10WEIGHT,COATING COATING WEIGHT THE WEIGHT OF THE COATING TO BE APPLIED TO THE ITEM. 1D AND 1B MODE REPLY12AG69 BWDDD /D/ 07HANDLE,COVER COVER HANDLE AN INDICATION OF WHETHER OR NOT THE COVER IS FURNISHED WITH A HANDLE. SELECT REPLY CODE 10AA55 BWDFD /D/ 18TYPE,HANDLE,COVER COVER HANDLE TYPE INDICATES THE TYPE OF COVER HANDLE PROVIDED. SELECT REPLY CODE 10AC55 BWDGH /D/ 19CHARACTERISTIC AND LOCATION,GLAZE GLAZE CHARACTERISTIC AND LOCATION AN INDICATION OF WHETHER OR NOT A GLAZE CHARACTERISTIC IS PROVIDED AND ITS LOCATION ON THE ITEM. 2D MODE REPLY 23AK393AJ91 BWDHD /D/ 18TYPE FOR WHICH DESIGNED,HEADWEAR HEADWEAR TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF HEADWEAR FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AG74 BWDJD /D/ 07INTERIOR,BLACK BLACK INTERIOR AN INDICATION OF WHETHER OR NOT THE COLOR PROVIDED ON THE INSIDE SURFACE IS BLACK. SELECT REPLY CODE 10AB22 BWDKD /D/ 07STOPCOCK,BASE BASE STOPCOCK AN INDICATION OF WHETHER OR NOT A BASE STOPCOCK IS PROVIDED. SELECT REPLY CODE 10AB22 BWDLD /D/ 07KNOB KNOB AN INDICATION OF WHETHER OR NOT THE ITEM IS FURNISHED WITH A KNOB. SELECT REPLY CODE 10AA55 BWDMD /D/ 18TYPE,OPENING,TOP TOP OPENING TYPE INDICATES THE TYPE OF OPENING PROVIDED AT THE TOP OF THE ITEM. SELECT REPLY CODE 10AM35 BWDND 07ADJUSTABILITY,LENGTH,ARM ARM LENGTH ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE ARM LENGTH IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BWDPJ /D/ 04LENGTH,ARM,EXTENDED EXTENDED ARM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ARM WHEN FULLY EXTENDED. 2D AND 1B MODE REPLY21AA051AC20 BWDQJ 04LENGTH,ARM,CLOSED CLOSED ARM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ARM WHEN IN A COMPLETELY CLOSED POSITION. 2D AND 1B MODE REPLY21AA051AC20 BWDRG /D/ 08LOCATION,HOLE,MOUNTING MOUNTING HOLE LOCATION INDICATES THE LOCATION OF THE MOUNTING HOLE(S) IN OR ON THE ITEM. FULL TEXT WRITE-IN 0 BWDSJ 04DIAMETER,HOLE,MOUNTING,MIRROR MIRROR MOUNTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MIRROR MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BWDTD /D/ 09MATERIAL,MIRROR MIRROR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MIRROR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BWDWD 14SHAPE,MIRROR MIRROR SHAPE THE PHYSICAL CONFIGURATION OF THE MIRROR. SELECT REPLY CODE 10AD07 BWDXD /D/ 07OPENING,WINDOW WINDOW OPENING AN INDICATION OF WHETHER OR NOT A WINDOW OPENING(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BWDYD /D/ 07FRAME,METAL METAL FRAME AN INDICATION OF WHETHER OR NOT A METAL FRAME(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BWDZD /D/ 07OPENING,REACH-IN REACH-IN OPENING AN INDICATION OF WHETHER OR NOT A REACH-IN OPENING IS INCLUDED. SELECT REPLY CODE 10AA49 BWFBD /D/ 07FEATURE,DESIGN,ROLL UP ROLL UP DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A ROLL UP DESIGN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BWFCD /D/ 07CORNER,METAL,DETACHABLE DETACHABLE METAL CORNER AN INDICATION OF WHETHER OR NOT A DETACHABLE METAL CORNER(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BWFDD /D/ 07LEG,SIDE SIDE LEG AN INDICATION OF WHETHER OR NOT A SIDE LEG(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BWFFJ 04WIDTH,END,MOUNTING MOUNTING END WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING END,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BWFGJ 04THICKNESS,END,MOUNTING MOUNTING END THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE MOUNTING END,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BWFHJ 10OFFSET FROM LEG CENTERLINE,END,MOUNTING MOUNTING END OFFSET FROM LEG CENTERLINE A MEASUREMENT OF THE MOUNTING END OFFSET FROM THE LEG CENTERLINE. 2D AND 1B MODE REPLY21AA051AC20 BWFJA 12QUANTITY,HOLE,MOUNTING END MOUNTING END HOLE QUANTITY THE NUMBER OF MOUNTING END HOLES PROVIDED. 1A MODE REPLY 0 BWFKJ 04DIAMETER,HOLE,MOUNTING END MOUNTING END HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR MOUNTING END HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BWFLD /D/ 02DESIGN,WAIST WAIST DESIGN THE DESIGN OF THE PORTION OF A GARMENT THAT ENCIRCLES THE WAIST. SELECT REPLY CODE 10AH80 BWFMD /D/ 09MATERIAL,SURFACE,WEAR WEAR SURFACE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WEAR SURFACE IS FABRICATED. SELECT REPLY CODE 10AD09 BWFNJ 04DISTANCE BETWEEN MOUNTING PIVOT AND LINKAGE CONTACT,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING PIVOT AND LINKAGE CONTACT THE CENTER TO CENTER DISTANCE BETWEEN THE MOUNTING PIVOT AND THE LINKAGE CONTACT. 2D AND 1B MODE REPLY21AA051AC20 BWFPJ 04WIDTH,KNUCKLE KNUCKLE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A KNUCKLE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BWFQJ 04DISTANCE BETWEEN SOCKET HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SOCKET HOLES THE CENTER TO CENTER DISTANCE BETWEEN THE SOCKET HOLES. 2D AND 1B MODE REPLY21AA051AC20 BWFRD 18TYPE,DEVICE,CONNECTING CONNECTING DEVICE TYPE INDICATES THE TYPE OF CONNECTING DEVICE PROVIDED. SELECT REPLY CODE 10AK54 BWFSD 18TYPE,DEVICE,MANUAL CONTROL MANUAL CONTROL DEVICE TYPE INDICATES THE TYPE OF MANUAL CONTROL DEVICE PROVIDED. SELECT REPLY CODE 10AM97 BWFTD /D/ 07HOLE,BOLT,MOUNTING END MOUNTING END BOLT HOLE AN INDICATION OF WHETHER OR NOT A MOUNTING END BOLT HOLE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BWFWD 08LOCATION,SWITCH SWITCH LOCATION INDICATES THE LOCATION OF THE SWITCH ON THE ITEM. SELECT REPLY CODE 10AJ91 BWFXG 19MARKING,SWITCH SWITCH MARKING AN INDICATION OF THE MARKING(S) ON THE SWITCH. FULL TEXT WRITE-IN 0 BWFYG 19MARKING,RESISTOR RESISTOR MARKING AN INDICATION OF THE MARKING(S) ON THE RESISTOR. FULL TEXT WRITE-IN 0 BWFZD /D/ 07CABLE,ELECTRICAL ELECTRICAL CABLE AN INDICATION OF WHETHER OR NOT AN ELECTRICAL CABLE IS INCLUDED. SELECT REPLY CODE 10AA49 BWGBD /D/ 18TYPE FOR WHICH DESIGNED,MOUNTING MOUNTING TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF MOUNTING FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AM39 BWGCD 18TYPE,ARM,LIFT LIFT ARM TYPE INDICATES THE TYPE OF LIFT ARM PROVIDED. SELECT REPLY CODE 10AK54 BWGDJ 10TRAVEL,MAXIMUM,LIFT ARM LIFT ARM MAXIMUM TRAVEL THE MAXIMUM DISTANCE THE LIFT ARM WILL TRAVEL. 1D AND 1B MODE REPLY11AA05 BWGFD 14SHAPE,SHAFT,HANDLE HANDLE SHAFT SHAPE THE PHYSICAL CONFIGURATION OF THE HANDLE SHAFT. SELECT REPLY CODE 10AD07 BWGGD /D/ 07PLATE,HANDLE/ESCUTCHEON HANDLE/ESCUTCHEON PLATE AN INDICATION OF WHETHER OR NOT A HANDLE AND/OR ESCUTCHEON PLATE IS INCLUDED. SELECT REPLY CODE 10AA49 BWGHD /D/ 07CHANNEL,LIFT,GLASS GLASS LIFT CHANNEL AN INDICATION OF WHETHER OR NOT A GLASS LIFT CHANNEL IS INCLUDED. SELECT REPLY CODE 10AA49 BWGJD 18TYPE,TRACK,ACTUATOR ACTUATOR TRACK TYPE INDICATES THE TYPE OF ACTUATOR TRACK PROVIDED. SELECT REPLY CODE 10AK54 BWGKJ /D/ 10RATING,BUOYANCY BUOYANCY RATING THE RATE OF HOW MUCH WEIGHT A FLOTATION DEVICE CAN SAFELY KEEP ABOVE WATER. 2D AND 1B MODE REPLY21AC202AG67 BWGLJ 04LENGTH,SECTION SECTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BWGMJ 04LENGTH,SLOT,SECTION SECTION SLOT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SECTION SLOT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BWGND /D/ 07FEATURE,SEPARATION,SECTION SECTION SEPARATION FEATURE AN INDICATION OF WHETHER OR NOT A SECTION SEPARATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BWGPA 12QUANTITY,SECTION SECTION QUANTITY THE NUMBER OF SECTIONS INCLUDED. 1A MODE REPLY 0 BWGQD /D/ 07HOOKS,ROOF ROOF HOOKS AN INDICATION OF WHETHER OR NOT ROOF HOOKS ARE INCLUDED. SELECT REPLY CODE 10AA49 BWGRD /D/ 07CAPS,END END CAPS AN INDICATION OF WHETHER OR NOT END CAPS ARE INCLUDED. SELECT REPLY CODE 10AA49 BWGSD /D/ 07FEATURE,MOBILITY MOBILITY FEATURE AN INDICATION OF WHETHER OR NOT A MOBILITY FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BWGTJ 04WIDTH,STEP,INTERMEDIATE INTERMEDIATE STEP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE INTERMEDIATE STEP(S),IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BWGWD /D/ 17SURFACE TREATMENT,RUNG RUNG SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE RUNG. SELECT REPLY CODE 10AD09 BWGXD /D/ 09MATERIAL,SIDE SIDE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SIDE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BWGYD /D/ 17SURFACE TREATMENT,SIDE SIDE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SIDE SURFACE. SELECT REPLY CODE 10AD09 BWGZD /D/ 17SURFACE TREATMENT,DISK DISK SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE DISK SURFACE. SELECT REPLY CODE 10AD09 BWHBJ 10SPACING,RUNG RUNG SPACING THE SPACING OF THE RUNG ON THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BWHCD /D/ 07LANYARD LANYARD AN INDICATION OF WHETHER OR NOT A LANYARD(S) IS INCLUDED. MRC IS DISCONTINUED AND REPLACED WITH MRC ABFF AND REPLY CODE AQJ, LANYARD ON 03/28/2024. SELECT REPLY CODE 10AA49 BWHDD 08LOCATION,LANYARD LANYARD LOCATION INDICATES THE LOCATION OF THE LANYARD(S). SELECT REPLY CODE 10AJ91 BWHFJ 04DISTANCE FROM BASE TO TOP STEP DISTANCE FROM BASE TO TOP STEP THE DISTANCE FROM THE BASE OF THE ITEM TO THE TOP STEP. 2D AND 1B MODE REPLY21AA051AC20 BWHGD /D/ 07STEPS,OPPOSING OPPOSING STEPS AN INDICATION OF WHETHER OR NOT OPPOSING STEPS ARE INCLUDED. SELECT REPLY CODE 10AA49 BWHHJ 04WIDTH,STEP,TOP TOP STEP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TOP STEP,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BWHJD /D/ 07HANDRAILS HANDRAILS AN INDICATION OF WHETHER OR NOT HANDRAILS ARE INCLUDED. SELECT REPLY CODE 10AA49 BWHKJ 04HEIGHT ABOVE TOP STEP,HANDRAIL HANDRAIL HEIGHT ABOVE TOP STEP A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE HANDRAIL ABOVE THE TOP STEP,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BWHLD /D/ 07EXTENSION AROUND TOP STEP EXTENSION AROUND TOP STEP AN INDICATION OF WHETHER OR NOT AN EXTENSION AROUND THE TOP STEP IS INCLUDED. SELECT REPLY CODE 10AA49 BWHMD 18TYPE,WHEEL,FRONT FRONT WHEEL TYPE INDICATES THE TYPE OF FRONT WHEEL(S) PROVIDED ON THE ITEM. SELECT REPLY CODE 10AK54 BWHNJ 10CLEARANCE BETWEEN CUTTING EDGE AND GROUND AT MAXIMUM BLADE ELEVATION,MINIMUM MINIMUM CLEARANCE BETWEEN CUTTING EDGE AND GROUND AT MAXIMUM BLADE ELEVATION THE MINIMUM CLEARANCE BETWEEN THE CUTTING EDGE AND GROUND AT MAXIMUM BLADE ELEVATION. 1D AND 1B MODE REPLY11AA05 BWHPG /D/ 04ANGLE IN DEG,CUTTING,BLADE MAXIMUM BANK BLADE MAXIMUM BANK CUTTING ANGLE IN DEG THE MAXIMUM BANK CUTTING ANGLE OF THE BLADE,EXPRESSED IN DEGREES. FULL TEXT WRITE-IN 0 BWHQD 11METHOD,CONTROL,BLADE BLADE CONTROL METHOD THE MEANS OF CONTROLLING THE BLADE. SELECT REPLY CODE 10AK54 BWHRD /D/ 07CONTROL,BLADE,AUTOMATIC AUTOMATIC BLADE CONTROL AN INDICATION OF WHETHER OR NOT AN AUTOMATIC BLADE CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 BWHSJ 10PULL RATING,BLADE BLADE PULL RATING THE PULL FOR WHICH THE BLADE IS RATED,PER MEASUREMENT SCALE. 2D AND 1B MODE REPLY21AB101AC20 BWHTD 11METHOD,CONTROL,STEERING STEERING CONTROL METHOD THE MEANS OF CONTROLLING THE STEERING. SELECT REPLY CODE 10AK54 BWHWD /D/ 18TYPE,MOUNTING,FULL TRACKED TRACTOR FRAME FULL TRACKED TRACTOR FRAME MOUNTING TYPE INDICATES THE TYPE OF FULL TRACKED TRACTOR FRAME MOUNTING PROVIDED. SELECT REPLY CODE 10AK54 BWHXJ 04HEIGHT,OVERALL,BLADE BLADE OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE BLADE. 2D AND 1B MODE REPLY21AA051AC20 BWHYJ 04WIDTH,CUT,SCOOP SCOOP CUT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CUT FOR WHICH THE SCOOP IS DESIGNED,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BWHZD 07REVERSIBILITY,EDGE,BLADE CUTTING BLADE CUTTING EDGE REVERSIBILITY AN INDICATION OF WHETHER OR NOT THE BLADE CUTTING EDGE IS REVERSIBLE. SELECT REPLY CODE 10AF62 BWJBD /D/ 07FEATURE,DESIGN,TRACTOR MOUNTING TRACTOR MOUNTING DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A TRACTOR MOUNTING DESIGN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BWJCJ T10RATING FOR WHICH DESIGNED,PULL,DRAWBAR DRAWBAR PULL RATING FOR WHICH DESIGNED THE DRAWBAR PULL RATING FOR WHICH THE ITEM IS DESIGNED. 1D AND 1F MODE REPLY11AB10 BWJDD 18TYPE,BEVEL BEVEL TYPE INDICATES THE TYPE OF BEVEL ON THE ITEM. SELECT REPLY CODE 10AC66 BWJFD 19SIDE FOR WHICH DESIGNED SIDE FOR WHICH DESIGNED AN INDICATION OF THE SIDE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AJ91 BWJGG 04DISTANCE BETWEEN BOLT HOLES FROM END TO END,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES FROM END TO END THE CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES FROM END TO END. FULL TEXT WRITE-IN 0 BWJHJ 04WIDTH ACROSS FLATS,HOLE HOLE WIDTH ACROSS FLATS THE SHORTEST STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT OF THE HOLE. 2D AND 1B MODE REPLY21AA051AC20 BWJJD /D/ 07HOLE,BOLT,COUNTERSUNK COUNTERSUNK BOLT HOLE AN INDICATION OF WHETHER OR NOT A COUNTERSUNK BOLT HOLE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BWJKD /D/ 18TYPE FOR WHICH DESIGNED,BOLT BOLT TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF BOLT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BWJLG 04SIZE FOR WHICH DESIGNED,BOLT BOLT SIZE FOR WHICH DESIGNED DESIGNATES THE BOLT SIZE FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 BWJMD 11METHOD,OPERATION,SCOOP SCOOP OPERATION METHOD THE MEANS UTILIZED TO OPERATE THE SCOOP. SELECT REPLY CODE 10AC58 BWJND /D/ 08LOCATION,MOUNTING,UPPER WORKING SURFACE UPPER WORKING SURFACE MOUNTING LOCATION INDICATES THE LOCATION OF THE ITEM ON WHICH THE UPPER WORKING SURFACE IS MOUNTED. SELECT REPLY CODE 10AJ91 BWJPJ /D/ 04DISTANCE FROM CHUCK/SPINDLE NOSE TO UPPER WORKING SURFACE,MAXIMUM MAXIMUM DISTANCE FROM CHUCK/SPINDLE NOSE TO UPPER WORKING SURFACE THE MAXIMUM DISTANCE FROM THE CHUCK OR SPINDLE NOSE TO THE UPPER WORKING SURFACE. 1D AND 1B MODE REPLY11AA05 BWJQD 18TYPE,SURFACE,WORKING,INTERMEDIATE INTERMEDIATE WORKING SURFACE TYPE INDICATES THE TYPE OF INTERMEDIATE WORKING SURFACE PROVIDED ON THE ITEM. SELECT REPLY CODE 10AK54 BWJRD 14SHAPE,SURFACE,WORKING,INTERMEDIATE INTERMEDIATE WORKING SURFACE SHAPE THE PHYSICAL CONFIGURATION OF THE INTERMEDIATE WORKING SURFACE. SELECT REPLY CODE 10AD07 BWJSJ /D/ 10AREA,SURFACE,WORKING,INTERMEDIATE INTERMEDIATE WORKING SURFACE AREA A MEASUREMENT OF THE INTERMEDIATE WORKING SURFACE AREA ON THE ITEM. 1D AND 1B MODE REPLY12AG67 BWJTJ 04DIAMETER,SURFACE,WORKING,INTERMEDIATE INTERMEDIATE WORKING SURFACE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INTERMEDIATE WORKING SURFACE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BWJWJ /D/ 04HEIGHT,SURFACE,WORKING,INTERMEDIATE INTERMEDIATE WORKING SURFACE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE INTERMEDIATE WORKING SURFACE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BWJXJ /D/ 04LENGTH,SURFACE,WORKING,INTERMEDIATE INTERMEDIATE WORKING SURFACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE INTERMEDIATE WORKING SURFACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BWJYJ /D/ 04WIDTH,SURFACE,WORKING,INTERMEDIATE INTERMEDIATE WORKING SURFACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE INTERMEDIATE WORKING SURFACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BWJZD /D/ 08LOCATION,MOUNTING,INTERMEDIATE WORKING SURFACE INTERMEDIATE WORKING SURFACE MOUNTING LOCATION INDICATES THE LOCATION OF THE ITEM ON WHICH THE INTERMEDIATE WORKING SURFACE IS MOUNTED. SELECT REPLY CODE 10AJ91 BWKBJ /D/ 04DISTANCE FROM CHUCK/SPINDLE NOSE TO INTERMEDIATE WORKING SURFACE,MAXIMUM MAXIMUM DISTANCE FROM CHUCK/SPINDLE NOSE TO INTERMEDIATE WORKING SURFACE THE DISTANCE FROM THE CHUCK OR SPINDLE NOSE TO THE INTERMEDIATE WORKING SURFACE. 1D AND 1B MODE REPLY11AA05 BWKCD 07ADJUSTABILITY,SPAN,COLUMN COLUMN SPAN ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE SPAN BETWEEN COLUMNS IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BWKDJ 04DISTANCE BETWEEN COLUMNS DISTANCE BETWEEN COLUMNS THE DISTANCE BETWEEN COLUMNS. 2D AND 1B MODE REPLY21AA051AC20 BWKFJ 10SPREAD BETWEEN BED PLATES,MAXIMUM MAXIMUM SPREAD BETWEEN BED PLATES THE MAXIMUM DISTANCE BETWEEN THE BED PLATES. 1D AND 1B MODE REPLY11AA05 BWKGJ 04DISTANCE,TRAVEL,BED BED TRAVEL DISTANCE THE DISTANCE THE BED IS DESIGNED TO TRAVEL. 2D AND 1B MODE REPLY21AA051AC20 BWKHD /D/ 07PLATE,SWIVEL SWIVEL PLATE AN INDICATION OF WHETHER OR NOT A SWIVEL PLATE IS INCLUDED. SELECT REPLY CODE 10AA49 BWKJJ 04DISTANCE BETWEEN UPRIGHTS DISTANCE BETWEEN UPRIGHTS THE DISTANCE BETWEEN UPRIGHTS. 2D AND 1B MODE REPLY21AA051AC20 BWKKJ 04DISTANCE FROM RAM CENTER TO FRAME FRONT DISTANCE FROM RAM CENTER TO FRAME FRONT THE DISTANCE FROM THE CENTER OF THE RAM TO THE FRONT OF THE FRAME. 2D AND 1B MODE REPLY21AA051AC20 BWKLJ 04LENGTH,STROKE,SLIDE SLIDE STROKE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SLIDE STROKE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BWKMJ 04DISTANCE,FRONT TO BACK,BED BED FRONT TO BACK DISTANCE THE DISTANCE FROM THE FRONT OF THE BED TO THE BACK OF THE BED. 2D AND 1B MODE REPLY21AA051AC20 BWKNJ 04DISTANCE,RIGHT TO LEFT,BED BED RIGHT TO LEFT DISTANCE THE DISTANCE FROM THE RIGHT OF THE BED TO THE LEFT OF THE BED. 2D AND 1B MODE REPLY21AA051AC20 BWKPJ 04DISTANCE,FRONT TO BACK,BED OPENING BED OPENING FRONT TO BACK DISTANCE THE DISTANCE FROM THE FRONT OF THE BED OPENING TO THE BACK OF THE BED OPENING. 2D AND 1B MODE REPLY21AA051AC20 BWKQJ 04DISTANCE,RIGHT TO LEFT,BED OPENING BED OPENING RIGHT TO LEFT DISTANCE THE DISTANCE FROM THE RIGHT OF THE BED OPENING TO THE LEFT OF THE BED OPENING. 2D AND 1B MODE REPLY21AA051AC20 BWKRJ 04DISTANCE ACROSS FLATS,RECESS RECESS DISTANCE ACROSS FLATS THE DISTANCE ACROSS THE RECESS FLATS. 2D AND 1B MODE REPLY21AA051AC20 BWKSJ 10SPACE,DIE DIE SPACE THE DIE SPACE ON THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BWKTD /D/ 07PLATE,BOLSTER BOLSTER PLATE AN INDICATION OF WHETHER OR NOT A BOLSTER PLATE IS INCLUDED. SELECT REPLY CODE 10AA49 BWKWD 18TYPE,KNOCKOUT,SLIDE SLIDE KNOCKOUT TYPE INDICATES THE TYPE OF KNOCKOUT PROVIDED IN THE SLIDE. SELECT REPLY CODE 10AH28 BWKXJ 10WATTAGE RATING IN WATTS,INPUT INPUT WATTAGE RATING IN WATTS THE RATED INPUT POWER OF THE ITEM,EXPRESSED IN WATTS. 1D AND 1B MODE REPLY11AC20 BWKYJ 10PRESSURE REQUIRED,AIR,MINIMUM MINIMUM AIR PRESSURE REQUIRED THE MINIMUM AIR PRESSURE REQUIRED TO OPERATE THE ITEM. 1D AND 1B MODE REPLY12AG67 BWKZG 10CONSUMPTION RATE,AIR AIR CONSUMPTION RATE THE AMOUNT OF AIR CONSUMED BY THE ITEM. FULL TEXT WRITE-IN 0 BWLBD /D/ 07BRUSH,REVOLVING REVOLVING BRUSH AN INDICATION OF WHETHER OR NOT A REVOLVING BRUSH IS INCLUDED. SELECT REPLY CODE 10AA49 BWLCD /D/ 07OUTLET,BLOWER BLOWER OUTLET AN INDICATION OF WHETHER OR NOT A BLOWER OUTLET IS INCLUDED. SELECT REPLY CODE 10AA49 BWLDD /D/ 07FEATURE,DESIGN,WATER LIFT WATER LIFT DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A WATER LIFT DESIGN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BWLFD 02DESIGN,TANK,WATER WATER TANK DESIGN THE DESIGN OF THE WATER TANK ON THE ITEM. SELECT REPLY CODE 10AK54 BWLGD /D/ 07ABSORBER,WATER,SQUEEGEE SQUEEGEE WATER ABSORBER AN INDICATION OF WHETHER OR NOT A SQUEEGEE WATER ABSORBER IS INCLUDED. SELECT REPLY CODE 10AA49 BWLHD /D/ 07DISPENSER,WAX,HOT HOT WAX DISPENSER AN INDICATION OF WHETHER OR NOT A HOT WAX DISPENSER IS INCLUDED. SELECT REPLY CODE 10AA49 BWLJD /D/ 07REEL,CABLE,AUTOMATIC WINDING AUTOMATIC WINDING CABLE REEL AN INDICATION OF WHETHER OR NOT AN AUTOMATIC WINDING CABLE REEL IS INCLUDED. SELECT REPLY CODE 10AA49 BWLKJ /D/ 10VELOCITY,DISCHARGE,MINIMUM MINIMUM DISCHARGE VELOCITY THE MINIMUM DISCHARGE RATE OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BWLLD /D/ 09MATERIAL,HOLDER,BLADE BLADE HOLDER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BLADE HOLDER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BWLMD 07ADJUSTABILITY,SOCKET,HANDLE HANDLE SOCKET ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE HANDLE SOCKET IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BWLND /D/ 14SHAPE,SHANK,ARBOR ARBOR SHANK SHAPE THE PHYSICAL CONFIGURATION OF THE ARBOR SHANK. SELECT REPLY CODE 10AD07 BWLPJ 04WIDTH ACROSS FLATS,SHANK SHANK WIDTH ACROSS FLATS THE SHORTEST STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT OF THE SHANK. 2D AND 1B MODE REPLY21AA051AC20 BWLQG /D/ 04SIZE,TAPER,SHANK SHANK TAPER SIZE DESIGNATES THE SHANK TAPER SIZE. FULL TEXT WRITE-IN 0 BWLRD /D/ 09MATERIAL,DRILL,PILOT PILOT DRILL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PILOT DRILL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BWLSD 18TYPE FOR WHICH DESIGNED,CUT CUT TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF CUT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL18 BWLTJ 04WIDTH,SECTION,ROLLER ROLLER SECTION WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A ROLLER SECTION,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BWLWB 04ANGLE IN DEG,TILT,FORWARD,TABLE TABLE FORWARD TILT ANGLE IN DEG THE FORWARD TILT ANGLE OF THE TABLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BWLXB 04ANGLE IN DEG,TILT,REARWARD,TABLE TABLE REARWARD TILT ANGLE IN DEG THE REARWARD TILT ANGLE OF THE TABLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BWLYB 04ANGLE IN DEG,TILT,RIGHT,TABLE TABLE RIGHT TILT ANGLE IN DEG THE RIGHT TILT ANGLE OF THE TABLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BWLZB 04ANGLE IN DEG,TILT,LEFT,TABLE TABLE LEFT TILT ANGLE IN DEG THE LEFT TILT ANGLE OF THE TABLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BWMBB 04ANGLE FROM SAW IN DEG,TILT,RIGHT,TABLE TABLE RIGHT TILT ANGLE FROM SAW IN DEG THE RIGHT TILT ANGLE OF THE TABLE FROM THE SAW,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BWMCD /D/ 18TYPE FOR WHICH DESIGNED,BAND BAND TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF BAND FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BWMDJ 04LENGTH ACCOMMODATED,MAXIMUM,FILE FILE MAXIMUM LENGTH ACCOMMODATED THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF THE FILE THE ITEM WILL ACCOMMODATE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BWMFJ 04WIDTH ACCOMMODATED,MAXIMUM,FILE FILE MAXIMUM WIDTH ACCOMMODATED THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FILE THE ITEM WILL ACCOMMODATE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BWMGJ 04LENGTH ACCOMMODATED,MAXIMUM,BLADE BLADE MAXIMUM LENGTH ACCOMMODATED THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF THE BLADE THE ITEM WILL ACCOMMODATE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BWMHJ 04WIDTH ACCOMMODATED,MAXIMUM,BLADE BLADE MAXIMUM WIDTH ACCOMMODATED THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BLADE THE ITEM WILL ACCOMMODATE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BWMJB 04ANGLE IN DEG,TILT,RIGHT,FRAME FRAME RIGHT TILT ANGLE IN DEG THE RIGHT TILT ANGLE OF THE FRAME,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BWMKB 04ANGLE IN DEG,TILT,LEFT,FRAME FRAME LEFT TILT ANGLE IN DEG THE LEFT TILT ANGLE OF THE FRAME,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BWMLD /D/ 07VISE VISE AN INDICATION OF WHETHER OR NOT A VISE IS PROVIDED. SELECT REPLY CODE 10AB22 BWMMA 12QUANTITY,SPEED,STROKE STROKE SPEED QUANTITY THE NUMBER OF STROKE SPEEDS PROVIDED. 1A MODE REPLY 0 BWMNJ 04DISTANCE BETWEEN GUIDE AND TABLE DISTANCE BETWEEN GUIDE AND TABLE THE DISTANCE BETWEEN THE GUIDE AND THE TABLE. 2D AND 1B MODE REPLY21AA051AC20 BWMPJ 04DISTANCE BETWEEN SAW AND COLUMN DISTANCE BETWEEN SAW AND COLUMN THE DISTANCE BETWEEN THE SAW AND THE COLUMN. 2D AND 1B MODE REPLY21AA051AC20 BWMQJ A10SPEED IN STROKES PER MINUTE,SAWING SAWING SPEED IN STROKES PER MINUTE THE SPEED OF THE SAW,EXPRESSED IN STROKES PER MINUTE. 1D AND 1A MODE REPLY11AC20 BWMRJ 04THICKNESS ACCOMMODATED,STOCK,MAXIMUM MAXIMUM STOCK THICKNESS ACCOMMODATED THE MAXIMUM MEASUREMENT OF THE SMALLEST DIMENSION OF THE ACCOMMODATION FOR THE STOCK,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 BWMSJ 10CAPACITY,BLADE BLADE CAPACITY THE CAPACITY OF THE BLADE. 1D AND 1B MODE REPLY11AA05 BWMTJ 04DEPTH,CUTTING,BLADE BLADE CUTTING DEPTH THE CUTTING MEASUREMENT BETWEEN SPECIFIED POINTS OF THE BLADE,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 BWMWD /D/ 07CONVEYOR,STOCK STOCK CONVEYOR AN INDICATION OF WHETHER OR NOT A STOCK CONVEYOR IS PROVIDED. SELECT REPLY CODE 10AB22 BWMXD /D/ 07MECHANISM,FEED,STOCK STOCK FEED MECHANISM AN INDICATION OF WHETHER OR NOT A STOCK FEED MECHANISM IS PROVIDED. SELECT REPLY CODE 10AB22 BWMYD 18TYPE,VISE VISE TYPE INDICATES THE TYPE OF VISE PROVIDED. SELECT REPLY CODE 10AK54 BWMZJ T10RANGE,SPEED,CUTTING CUTTING SPEED RANGE THE MINIMUM AND MAXIMUM LIMITS OF THE CUTTING SPEED. 1D AND 1F MODE REPLY12AG67 BWNBA 12QUANTITY,SPEED,CUTTING CUTTING SPEED QUANTITY THE NUMBER OF CUTTING SPEEDS PROVIDED. 1A MODE REPLY 0 BWNCD /D/ 07FEATURE,SPEED,INFINITE CUTTING INFINITE CUTTING SPEED FEATURE AN INDICATION OF WHETHER OR NOT AN INFINITE CUTTING SPEED FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BWNDD /D/ 07FEATURE,FEED,POWER POWER FEED FEATURE AN INDICATION OF WHETHER OR NOT A POWER FEED FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BWNFD 18TYPE,DEVICE,BRAKING BRAKING DEVICE TYPE INDICATES THE TYPE OF BRAKING DEVICE PROVIDED. SELECT REPLY CODE 10AK54 BWNGD /D/ 07SYSTEM,COOLANT,BUILT-IN BUILT-IN COOLANT SYSTEM AN INDICATION OF WHETHER OR NOT A BUILT-IN COOLANT SYSTEM IS INCLUDED. SELECT REPLY CODE 10AA49 BWNHD /D/ 07WELDER,BUTT,INTEGRAL INTEGRAL BUTT WELDER AN INDICATION OF WHETHER OR NOT AN INTEGRAL BUTT WELDER IS INCLUDED. SELECT REPLY CODE 10AA49 BWNJD /D/ 07GRINDER,INTEGRAL INTEGRAL GRINDER AN INDICATION OF WHETHER OR NOT AN INTEGRAL GRINDER IS INCLUDED. SELECT REPLY CODE 10AA49 BWNKJ 10FEED RATE FEED RATE AN INDICATION OF THE FEED RATE OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BWNLJ 04WIDTH,RIPPING,MAXIMUM MAXIMUM RIPPING WIDTH THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE RIP OF THE ITEM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BWNMJ 10CUT,CROSS,MAXIMUM MAXIMUM CROSS CUT THE MAXIMUM CROSS CUT OF THE ITEM. 1D AND 1B MODE REPLY11AA05 BWNNJ 10FEED,VERTICAL,RAM HEAD RAM HEAD VERTICAL FEED THE MEASURED VERTICAL TRAVEL THE RAM HEAD WILL FEED. 2D AND 1B MODE REPLY21AA051AC20 BWNPD /D/ 07FEATURE,GEARED,BACK BACK GEARED FEATURE AN INDICATION OF WHETHER OR NOT A BACK GEARED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BWNQD /D/ 07FEATURE,OPERATED,HYDRAULICALLY HYDRAULICALLY OPERATED FEATURE AN INDICATION OF WHETHER OR NOT A HYDRAULICALLY OPERATED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BWNRJ 04DISTANCE,TRAVEL,HORIZONTAL,TABLE TABLE HORIZONTAL TRAVEL DISTANCE THE DISTANCE THE TABLE IS DESIGNED TO TRAVEL IN A HORIZONTAL DIRECTION. 2D AND 1B MODE REPLY21AA051AC20 BWNSJ 04DISTANCE,TRAVEL,VERTICAL,TABLE TABLE VERTICAL TRAVEL DISTANCE THE DISTANCE THE TABLE IS DESIGNED TO TRAVEL IN A VERTICAL DIRECTION. 2D AND 1B MODE REPLY21AA051AC20 BWNTD 05DIRECTION,TRAVERSE,RAPID RAPID TRAVERSE DIRECTION THE DIRECTION OF THE RAPID TRAVERSE. SELECT REPLY CODE 10AJ46 BWNWJ 04DISTANCE,MAXIMUM,RAM TO TABLE RAM TO TABLE MAXIMUM DISTANCE THE MAXIMUM DISTANCE FROM THE RAM TO TABLE. 1D AND 1B MODE REPLY11AA05 BWNXD /D/ 07TREATMENT,RESISTANT,FUNGUS FUNGUS RESISTANT TREATMENT AN INDICATION OF WHETHER OR NOT A TREATMENT IS INCLUDED TO PRODUCE A FUNGUS RESISTANT CONDITION. SELECT REPLY CODE 10AA49 BWNYJ /D/ 04DISTANCE BETWEEN HOUSINGS DISTANCE BETWEEN HOUSINGS THE DISTANCE BETWEEN THE HOUSINGS ON THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BWNZJ /D/ 04DISTANCE BETWEEN COLUMN EDGE AND TOOL IN LEFT-HAND RAILHEAD,MAXIMUM MAXIMUM DISTANCE BETWEEN COLUMN EDGE AND TOOL IN LEFT-HAND RAILHEAD THE MAXIMUM DISTANCE FROM THE COLUMN EDGE TO THE TOOL IN LEFT-HAND RAILHEAD. 1D AND 1B MODE REPLY11AA05 BWPBJ /D/ 04DISTANCE FROM TABLE TO CROSSRAIL,MAXIMUM MAXIMUM DISTANCE FROM TABLE TO CROSSRAIL THE MAXIMUM DISTANCE FROM THE TABLE TO THE CROSSRAIL. 1D AND 1B MODE REPLY11AA05 BWPCJ /D/ 04LENGTH,STROKE,TABLE TABLE STROKE LENGTH THE DISTANCE OF THE TABLE STROKE. 1D AND 1B MODE REPLY11AA05 BWPDJ /D/ 04DISTANCE BETWEEN CHIP POCKETS DISTANCE BETWEEN CHIP POCKETS THE DISTANCE BETWEEN THE CHIP POCKETS. 2D AND 1B MODE REPLY21AA051AC20 BWPFA /D/ 12QUANTITY,TOOLHEAD,CROSSRAIL CUTTING CROSSRAIL CUTTING TOOLHEAD QUANTITY THE NUMBER OF CROSSRAIL CUTTING TOOLHEADS PROVIDED. 1A MODE REPLY 0 BWPGJ /D/ 04DISTANCE,DOWNFEED,CROSSRAIL CUTTING TOOLHEAD CROSSRAIL CUTTING TOOLHEAD DOWNFEED DISTANCE THE DOWNFEED DISTANCE OF THE CROSSRAIL CUTTING TOOLHEAD. 2D AND 1B MODE REPLY21AA051AC20 BWPHA /D/ 12QUANTITY,TOOLHEAD,SIDE CUTTING SIDE CUTTING TOOLHEAD QUANTITY THE NUMBER OF SIDE CUTTING TOOLHEADS PROVIDED. 1A MODE REPLY 0 BWPJJ /D/ 04DISTANCE,INFEED,SIDE CUTTING TOOLHEAD SIDE CUTTING TOOLHEAD INFEED DISTANCE THE INFEED DISTANCE OF THE SIDE CUTTING TOOLHEAD. 2D AND 1B MODE REPLY21AA051AC20 BWPKD /D/ 18TYPE,UNIT,POWER TRANSMITTING POWER TRANSMITTING UNIT TYPE INDICATES THE TYPE OF POWER TRANSMITTING UNIT PROVIDED. SELECT REPLY CODE 10AK95 BWPLJ T04DIAMETER RANGE ACCOMMODATED,PIPE PIPE DIAMETER RANGE ACCOMMODATED THE MINIMUM AND MAXIMUM DIMENSIONS OF THE PIPE DIAMETER THAT THE ITEM WILL ACCOMMODATE. 1D AND 1F MODE REPLY11AA05 BWPMJ /D/ 10PRESSURE,AIR,MINIMUM MINIMUM AIR PRESSURE THE MINIMUM AIR PRESSURE OF THE ITEM. PLEASE USE MRC BTWA IN PLACE OF THIS CANCELED MRC. 1D AND 1B MODE REPLY12AG67 BWPND 11METHOD,FEED,BLAST MATERIAL BLAST MATERIAL FEED METHOD THE MEANS BY WHICH THE BLAST MATERIAL IS FED. SELECT REPLY CODE 10AJ28 BWPPG 19DIMENSION ACCOMMODATED,OVERALL,CASTING CASTING OVERALL DIMENSION ACCOMMODATED A MEASUREMENT OF THE OVERALL DIMENSION OF THE CASTING THE ITEM WILL ACCOMMODATE. FULL TEXT WRITE-IN 0 BWPQA 12QUANTITY,NOZZLE NOZZLE QUANTITY THE NUMBER OF NOZZLES PROVIDED. 1A MODE REPLY 0 BWPRD /D/ 09MATERIAL,NOZZLE NOZZLE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE NOZZLE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH USE OF ISAC IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 BWPSJ 10SIZE,NOZZLE NOZZLE SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE NOZZLE. 2D AND 1B MODE REPLY21AA051AC20 BWPTD 18TYPE,CONTROL,BLASTING STREAM BLASTING STREAM CONTROL TYPE INDICATES THE TYPE OF BLASTING STREAM CONTROL PROVIDED. SELECT REPLY CODE 10AL37 BWPWD 18TYPE ACCOMMODATED,ABRASIVE ABRASIVE TYPE ACCOMMODATED INDICATES THE TYPE OF ABRASIVE THE ITEM WILL ACCOMMODATE. SELECT REPLY CODE 10AF67 BWPXD 18TYPE,COMPARTMENT,ABRASIVE TANK ABRASIVE TANK COMPARTMENT TYPE INDICATES THE TYPE OF ABRASIVE TANK COMPARTMENT PROVIDED. SELECT REPLY CODE 10AK54 BWPYA 12QUANTITY,OUTLET,BLAST HOSE BLAST HOSE OUTLET QUANTITY THE NUMBER OF BLAST HOSE OUTLETS PROVIDED. 1A MODE REPLY 0 BWPZJ 10PRESSURE,OPERATING,MAXIMUM,ABRASIVE TANK ABRASIVE TANK MAXIMUM OPERATING PRESSURE THE MAXIMUM PRESSURE AT WHICH THE ABRASIVE TANK IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY12AG67 BWQBJ 10CAPACITY AND TYPE,TANK,ABRASIVE ABRASIVE TANK CAPACITY AND TYPE THE ABRASIVE TANK CAPACITY AND THE TYPE. 2D AND 1B MODE REPLY22AG672AF67 BWQCD /D/ 07VALVE,STOP/START,INSTANTANEOUS BLAST INSTANTANEOUS BLAST STOP/START VALVE AN INDICATION OF WHETHER OR NOT AN INSTANTANEOUS BLAST STOP/START VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 BWQDD /D/ 07BOX,MIXER,AUTOMATIC START AUTOMATIC START MIXER BOX AN INDICATION OF WHETHER OR NOT AN AUTOMATIC START MIXER BOX IS INCLUDED. SELECT REPLY CODE 10AA49 BWQFD /D/ 07FEATURE,ADJUSTMENT,ABRASIVE ABRASIVE ADJUSTMENT FEATURE AN INDICATION OF WHETHER OR NOT AN ABRASIVE ADJUSTMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BWQGD /D/ 07CONTROL,REMOTE REMOTE CONTROL AN INDICATION OF WHETHER OR NOT A REMOTE CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 BWQHD /D/ 07ELEMENT,HEATING HEATING ELEMENT AN INDICATION OF WHETHER OR NOT A HEATING ELEMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BWQJD /D/ 07FEATURE,CONTROLLED,THERMOSTATICALLY,HOT AIR HOT AIR THERMOSTATICALLY CONTROLLED FEATURE AN INDICATION OF WHETHER OR NOT A HOT AIR THERMOSTATICALLY CONTROLLED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BWQKD /D/ 07FEATURE,SUSPENSION SUSPENSION FEATURE AN INDICATION OF WHETHER OR NOT A SUSPENSION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BWQLB 10VOLTAGE IN VOLTS,OPERATING,ELECTRIC MOTOR ELECTRIC MOTOR OPERATING VOLTAGE IN VOLTS THE AMOUNT OF OPERATING VOLTAGE OF THE ELECTRIC MOTOR,EXPRESSED IN VOLTS. 1B MODE REPLY 0 BWQMB 10FREQUENCY IN HERTZ,OPERATING,ELECTRIC MOTOR ELECTRIC MOTOR OPERATING FREQUENCY IN HERTZ THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT FOR WHICH THE ELECTRIC MOTOR IS RATED. 1B MODE REPLY 0 BWQNJ /D/ 10SIZE ACCOMMODATED,CHAIN/ROPE CHAIN/ROPE SIZE ACCOMMODATED NONE. 2D AND 1B MODE REPLY21AA051AC20 BWQQD /D/ 09MATERIAL,END,CONNECTION CONNECTION END MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CONNECTION END IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BWQRD /D/ 07FEATURE,COVERED,RUBBER RUBBER COVERED FEATURE AN INDICATION OF WHETHER OR NOT A RUBBER COVERED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BWQSD /D/ 07RING,UNATTACHED UNATTACHED RING AN INDICATION OF WHETHER OR NOT AN UNATTACHED RING IS INCLUDED. SELECT REPLY CODE 10AA49 BWQTJ 04DISTANCE BETWEEN BASES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN BASES THE CENTER TO CENTER DISTANCE BETWEEN THE BASES. 2D AND 1B MODE REPLY21AA051AC20 BWQWJ 04LENGTH ACROSS HORNS,OVERALL OVERALL LENGTH ACROSS HORNS THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS ACROSS THE HORNS. 2D AND 1B MODE REPLY21AA051AC20 BWQXD /D/ 07FEATURE,ACTION,CAM CAM ACTION FEATURE AN INDICATION OF WHETHER OR NOT A CAM ACTION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BWQYJ 04DISTANCE BETWEEN CUP AND MOUNTING HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN CUP AND MOUNTING HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BWQZJ 04HEIGHT,GRIP GRIP HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BWRBJ 04WIDTH BETWEEN CUP FLATS WIDTH BETWEEN CUP FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 BWRCJ 04DIAMETER,HOLE,END END HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BWRDJ 04DEPTH,CHAMFER,INSIDE INSIDE CHAMFER DEPTH NONE. REPLACED BY MRC AGHG WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 BWRFJ 04DEPTH,CHAMFER,OUTSIDE OUTSIDE CHAMFER DEPTH NONE. REPLACED BY MRC AGHG WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 BWRGB 04ANGLE IN DEG,CHAMFER,INSIDE INSIDE CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 BWRHB 04ANGLE IN DEG,CHAMFER,OUTSIDE OUTSIDE CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 BWRJD /D/ 07FEATURE,DESIGN,SPLIT SPLIT DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A SPLIT DESIGN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BWRKJ 04WIDTH,CROSS-SECTIONAL,BODY BODY CROSS-SECTIONAL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BWRLJ 04LENGTH,CROSS-SECTIONAL,CENTER HOLE CENTER HOLE CROSS-SECTIONAL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BWRMJ 04WIDTH,CROSS-SECTIONAL,CENTER HOLE CENTER HOLE CROSS-SECTIONAL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BWRNJ 04LENGTH,CROSS-SECTIONAL,BODY BODY CROSS-SECTIONAL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BWRPJ 04DIAMETER,LARGEST,TAPERED BODY TAPERED BODY LARGEST DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST END OF A TAPERED BODY,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BWRQJ 04DIAMETER,SMALLEST,TAPERED BODY TAPERED BODY SMALLEST DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST END OF A TAPERED BODY,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BWRRJ 04DIAMETER,SMALLEST,LONGER TAPER LONGER TAPER SMALLEST DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BWRSJ 04DIAMETER,SMALLEST,TAPERED CENTER HOLE TAPERED CENTER HOLE SMALLEST DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BWRTJ 04HEIGHT ABOVE FLANGE,BODY BODY HEIGHT ABOVE FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BWRWJ 04DIAMETER,LARGEST,TAPERED CENTER HOLE TAPERED CENTER HOLE LARGEST DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BWRXG /D/ 04RADIUS,CURVATURE,BODY END BODY END CURVATURE RADIUS NONE. FULL TEXT WRITE-IN 0 BWRYG /D/ 04DEG AND DISTANCE FROM BODY BOTTOM,BEVEL BEVEL DEG AND DISTANCE FROM BODY BOTTOM NONE. FULL TEXT WRITE-IN 0 BWRZG /D/ 04DEG AND DISTANCE FROM FLANGE TOP,BEVEL BEVEL DEG AND DISTANCE FROM FLANGE TOP NONE. FULL TEXT WRITE-IN 0 BWSBG /D/ 04DEG AND DISTANCE FROM BODY TOP,BEVEL BEVEL DEG AND DISTANCE FROM BODY TOP NONE. FULL TEXT WRITE-IN 0 BWSCJ 04RADIUS,CORNER,FLANGE FLANGE CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BWSDJ 04RADIUS,CORNER,FLANGE END HOLE FLANGE END HOLE CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BWSFJ 04RADIUS BETWEEN FLANGE AND BODY,CORNER CORNER RADIUS BETWEEN FLANGE AND BODY NONE. 2D AND 1B MODE REPLY21AA051AC20 BWSGJ 04RADIUS,CORNER,BODY TOP BODY TOP CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BWSHJ 04RADIUS,CORNER,CENTER HOLE TOP CENTER HOLE TOP CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BWSJJ 04THICKNESS,SURFACE,CONTACT CONTACT SURFACE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BWSKJ 04HEIGHT,PORTION,TAPERED TAPERED PORTION HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BWSLJ 04HEIGHT,BOTTOM,TAPERED PORTION BOTTOM TAPERED PORTION HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BWSMJ 04RADIUS,BODY,CONVEX CONVEX BODY RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 BWSND /D/ 07EDGE FOR FRAME INSERTION,BEADED BEADED EDGE FOR FRAME INSERTION AN INDICATION OF WHETHER OR NOT A BEADED EDGE FOR FRAME INSERTION IS INCLUDED. SELECT REPLY CODE 10AA49 BWSPD 18TYPE,SPONGE SPONGE TYPE INDICATES THE TYPE OF SPONGE. SELECT REPLY CODE 10AJ50 BWSQJ 10CIRCUMFERENCE CIRCUMFERENCE THE DISTANCE AROUND THE OUTSIDE OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BWSRJ 10WEIGHT PER DOZEN WEIGHT PER DOZEN A MEASUREMENT OF THE WEIGHT OF THE ITEM PER DOZEN. 1D AND 1B MODE REPLY12AG67 BWSSJ 04WIDTH,MOPHEAD MOPHEAD WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOPHEAD,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BWSTD 11METHOD,ATTACHMENT,MOPHEAD MOPHEAD ATTACHMENT METHOD THE MEANS USED TO ATTACH THE MOPHEAD. SELECT REPLY CODE 10AF69 BWSWJ 04LENGTH,CUTTING CUTTING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CUT THE ITEM IS CAPABLE OF MAKING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BWSXD /D/ 07FEATURE,NAPPED NAPPED FEATURE AN INDICATION OF WHETHER OR NOT A NAPPED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BWSYD /D/ 08LOCATION,NAP NAP LOCATION INDICATES THE LOCATION OF AN ITEM WHICH IS NAPPED. SELECT REPLY CODE 10AJ91 BWSZJ 10AREA,SURFACE,MINIMUM MINIMUM SURFACE AREA THE MINIMUM MEASUREMENT OF THE SURFACE AREA OF AN ITEM. 1D AND 1B MODE REPLY12AG67 BWTBJ /D/ 04WIDTH,SIDE SIDE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SIDE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BWTCJ /D/ 04LENGTH,OVERALL,BRISTLE SECTION BRISTLE SECTION OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BRISTLE SECTION OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BWTDJ /D/ 04LENGTH ABOVE BLOCK,BRISTLE BRISTLE LENGTH ABOVE BLOCK A MEASUREMENT OF THE LONGEST DIMENSION OF THE BRISTLE ABOVE THE BLOCK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BWTFD /D/ 07FEATURE,COMBINATION,SCRAPER/SQUEEGEE BLADE SCRAPER/SQUEEGEE BLADE COMBINATION FEATURE AN INDICATION OF WHETHER OR NOT A SCRAPER AND SQUEEGEE BLADE COMBINATION FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BWTGD /D/ 09MATERIAL,SCRAPER SCRAPER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SCRAPER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BWTHJ /D/ 04WIDTH,SCRAPER SCRAPER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SCRAPER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BWTJD /D/ 09MATERIAL,SQUEEGEE SQUEEGEE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SQUEEGEE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BWTKJ /D/ 04LENGTH,BLADE,SQUEEGUE SQUEEGUE BLADE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SQUEEGEE BLADE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BWTLJ /D/ 04HEIGHT OVER WORKING SURFACE,MAXIMUM MAXIMUM HEIGHT OVER WORKING SURFACE A MEASUREMENT OF THE MAXIMUM CLEARANCE OVER THE WORKING SURFACE. 2D AND 1B MODE REPLY21AA053AK54 BWTMJ 04DISTANCE,TRAVEL,WORKING SURFACE WORKING SURFACE TRAVEL DISTANCE THE DISTANCE THE WORKING SURFACE WILL TRAVEL. 3D AND 1B MODE REPLY31AA051AC203AK54 BWTNJ 04DISTANCE,TRAVEL,RAM RAM TRAVEL DISTANCE THE DISTANCE THE RAM WILL TRAVEL. 2D AND 1B MODE REPLY21AA051AC20 BWTPJ /D/ 04DISTANCE BETWEEN BED FACILITIES,FIXED FIXED DISTANCE BETWEEN BED FACILITIES THE FIXED DISTANCE BETWEEN BED FACILITIES. 3D AND 1B MODE REPLY31AA051AC203AK54 BWTQJ 04DISTANCE BETWEEN RAM AND WORKING SURFACE,MINIMUM MINIMUM DISTANCE BETWEEN RAM AND WORKING SURFACE THE MINIMUM DISTANCE BETWEEN THE RAM AND THE WORKING SURFACE. 2D AND 1B MODE REPLY21AA053AK54 BWTRJ 04DIAMETER,OUTSIDE,STEM STEM OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE STEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BWTSJ /D/ 04DIAMETER,OUTSIDE,BULB BULB OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BULB,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BWTTJ /D/ 04DIAMETER,INSIDE,CHAMBER CHAMBER INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CHAMBER,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BWTWJ /D/ 04LENGTH,INSIDE,CHAMBER CHAMBER INSIDE LENGTH A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF THE CHAMBER,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BWTXJ 04DIAMETER ACCOMMODATED,NECK,MAXIMUM MAXIMUM NECK DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE NECK,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BWTYD /D/ 07FLANGE,SECURING,CAP CAP SECURING FLANGE AN INDICATION OF WHETHER OR NOT A CAP SECURING FLANGE IS INCLUDED. SELECT REPLY CODE 10AA49 BWTZD /D/ 07TAB,CAP CAP TAB AN INDICATION OF WHETHER OR NOT A CAP TAB IS INCLUDED. SELECT REPLY CODE 10AA49 BWWBA 12QUANTITY,SOCKET,CAP CAP SOCKET QUANTITY THE NUMBER OF CAP SOCKETS PROVIDED. 1A MODE REPLY 0 BWWCA 12QUANTITY,APPLICATOR APPLICATOR QUANTITY THE NUMBER OF APPLICATORS PROVIDED. 1A MODE REPLY 0 BWWDD 14SHAPE,BULB BULB SHAPE THE PHYSICAL CONFIGURATION OF THE BULB. SELECT REPLY CODE 10AD07 BWWFD /D/ 18TYPE,FITTING,RECEIVER JOINT RECEIVER JOINT FITTING TYPE INDICATES THE TYPE OF RECEIVER JOINT FITTING PROVIDED. SELECT REPLY CODE 10AJ68 BWWGG /D/ 04SIZE,JOINT,RECEIVER RECEIVER JOINT SIZE DESIGNATES THE SIZE BY WHICH THE RECEIVER JOINT IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. FULL TEXT WRITE-IN 0 BWWHD /D/ 18TYPE,FITTING,DRAINER JOINT DRAINER JOINT FITTING TYPE INDICATES THE TYPE OF DRAINER JOINT FITTING PROVIDED. SELECT REPLY CODE 10AJ68 BWWJG /D/ 04SIZE,JOINT,DRAINER DRAINER JOINT SIZE DESIGNATES THE SIZE BY WHICH THE DRAINER JOINT IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. FULL TEXT WRITE-IN 0 BWWKG /D/ 04SIZE,PLUG,DRAINER DRAINER PLUG SIZE DESIGNATES THE SIZE BY WHICH THE DRAINER PLUG IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. FULL TEXT WRITE-IN 0 BWWLJ /D/ 04DIAMETER,BORE,DRAINER PLUG DRAINER PLUG BORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A DRAINER PLUG BORE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BWWMG /D/ 04SIZE,PLUG,VACUUM LINE VACUUM LINE PLUG SIZE DESIGNATES THE SIZE BY WHICH THE VACUUM LINE PLUG IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. FULL TEXT WRITE-IN 0 BWWND 19PHASE,MOTOR,ELECTRIC ELECTRIC MOTOR PHASE THE NUMBER OF ALTERNATING CURRENT PHASES FOR WHICH THE ELECTRIC MOTOR IS DESIGNED. SELECT REPLY CODE 10AD02 BWWPD 19TREATED FOR FUNGUS CONTROL,COMPONENT COMPONENT TREATED FOR FUNGUS CONTROL A DESIGNATION INDICATING WHICH COMPONENT/S/ IS TREATED TO CONTROL FUNGUS. SELECT REPLY CODE 10AN43 BWWQD /D/ 07GENERATOR,ULTRASONIC ULTRASONIC GENERATOR AN INDICATION OF WHETHER OR NOT AN ULTRASONIC GENERATOR IS INCLUDED. SELECT REPLY CODE 10AA49 BWWRJ 10POWER RATING,INPUT,GENERATOR GENERATOR INPUT POWER RATING THE VALUE OF ELECTRICAL INPUT POWER FOR WHICH THE GENERATOR IS RATED. 1D AND 1B MODE REPLY11AC33 BWWSJ 10POWER RATING,OUTPUT,GENERATOR GENERATOR OUTPUT POWER RATING THE VALUE OF ELECTRICAL OUTPUT POWER FOR WHICH THE GENERATOR IS RATED. 1D AND 1B MODE REPLY11AC33 BWWTJ T10RANGE,FREQUENCY,GENERATOR OUTPUT GENERATOR OUTPUT FREQUENCY RANGE THE RANGE OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE GENERATOR OUTPUT IS RATED. 1D AND 1F MODE REPLY11AC32 BWWWD 11METHOD,COOLING,GENERATOR GENERATOR COOLING METHOD THE MEANS BY WHICH THE GENERATOR IS COOLED. SELECT REPLY CODE 10AN05 BWWXJ 04HEIGHT,OVERALL,GENERATOR GENERATOR OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE GENERATOR. 2D AND 1B MODE REPLY21AA051AC20 BWWYJ 04WIDTH,OVERALL,GENERATOR GENERATOR OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE GENERATOR,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BWWZJ 04DEPTH,OVERALL,GENERATOR GENERATOR OVERALL DEPTH AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF THE GENERATOR,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BWXBD /D/ 07ASSEMBLY,CABLE,ELECTRICAL ELECTRICAL CABLE ASSEMBLY AN INDICATION OF WHETHER OR NOT AN ELECTRICAL CABLE ASSEMBLY IS INCLUDED. SELECT REPLY CODE 10AA49 BWXCG /D/ 19SPEC/STD,ASSEMBLY,ELECTRICAL CABLE ELECTRICAL CABLE ASSEMBLY SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO COVER THE CONSTRUCTION OF THE ELECTRICAL CABLE ASSEMBLY. FULL TEXT WRITE-IN 0 BWXDD /D/ 07RECONDITIONER,SOLVENT SOLVENT RECONDITIONER AN INDICATION OF WHETHER OR NOT A SOLVENT RECONDITIONER IS INCLUDED. SELECT REPLY CODE 10AA49 BWXFD /D/ 07PROVISION,CLEANING,SPRAY SPRAY CLEANING PROVISION AN INDICATION OF WHETHER OR NOT A SPRAY CLEANING PROVISION IS PROVIDED. SELECT REPLY CODE 10AB22 BWXGD /D/ 07SUPPLY,SOLVENT,AUXILIARY AUXILIARY SOLVENT SUPPLY AN INDICATION OF WHETHER OR NOT AN AUXILIARY SOLVENT SUPPLY IS INCLUDED. SELECT REPLY CODE 10AA49 BWXHD 18TYPE,PRESSURE,LINE LINE PRESSURE TYPE INDICATES THE TYPE OF LINE PRESSURE UTILIZED. SELECT REPLY CODE 10AL77 BWXJJ 04HEIGHT,BENCH BENCH HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BENCH,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BWXKD /D/ 07CURTAIN,FIRE,SAFETY SAFETY FIRE CURTAIN AN INDICATION OF WHETHER OR NOT A SAFETY FIRE CURTAIN IS INCLUDED. SELECT REPLY CODE 10AA49 BWXLD /D/ 07FAN,EXHAUST EXHAUST FAN AN INDICATION OF WHETHER OR NOT AN EXHAUST FAN IS INCLUDED. SELECT REPLY CODE 10AA49 BWXQB 10FREQUENCY IN HERTZ,MOTOR,FAN FAN MOTOR FREQUENCY IN HERTZ THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT FOR WHICH THE FAN MOTOR IS RATED. 1B MODE REPLY 0 BWXSD /D/ 07FEATURE,PROOF,EXPLOSION,FAN MOTOR FAN MOTOR EXPLOSION PROOF FEATURE AN INDICATION OF WHETHER OR NOT A FAN MOTOR EXLOSION PROOF FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BWXTA 12QUANTITY,SPEED,WINDING WINDING SPEED QUANTITY THE NUMBER OF WINDING SPEEDS PROVIDED. 1A MODE REPLY 0 BWXWF T10RANGE IN RPM,SPEED,WINDING WINDING SPEED RANGE IN RPM THE WINDING SPEED RANGE OF THE ITEM,EXPRESSED IN REVOLUTIONS PER MINUTE. 1F MODE REPLY 0 BWXXJ 04DIAMETER,FACEPLATE FACEPLATE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FACEPLATE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BWXYJ 04DISTANCE FROM FACEPLATE CENTER TO MOUNTING SURFACE DISTANCE FROM FACEPLATE CENTER TO MOUNTING SURFACE THE DISTANCE FROM THE CENTER OF THE FACEPLATE TO THE MOUNTING SURFACE. 2D AND 1B MODE REPLY21AA051AC20 BWXZD /D/ 07CHUCK CHUCK AN INDICATION OF WHETHER OR NOT A CHUCK IS INCLUDED. SELECT REPLY CODE 10AA49 BWYBD /D/ 07TAILSTOCK TAILSTOCK AN INDICATION OF WHETHER OR NOT A TAILSTOCK IS INCLUDED. SELECT REPLY CODE 10AA49 BWYCJ /D/ 04DISTANCE BETWEEN TAILSTOCK AND JOB HOLDING DEVICE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN TAILSTOCK AND JOB HOLDING DEVICE THE CENTER TO CENTER DISTANCE BETWEEN THE TAILSTOCK AND THE JOB HOLDING DEVICE. 2D AND 1B MODE REPLY21AA051AC20 BWYDD /D/ 07COUNTER,REVOLUTION REVOLUTION COUNTER AN INDICATION OF WHETHER OR NOT A REVOLUTION COUNTER IS INCLUDED. SELECT REPLY CODE 10AA49 BWYFD /D/ 07CONTROL,TREADLE,FOOT FOOT TREADLE CONTROL AN INDICATION OF WHETHER OR NOT A FOOT TREADLE CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 BWYGD 08LOCATION,ENTRANCE ENTRANCE LOCATION INDICATES THE LOCATION OF THE ENTRANCE(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 BWYHD /D/ 08LOCATION,THREAD,HOSE CONNECTION PIPE HOSE CONNECTION PIPE THREAD LOCATION THE PORTION OF THE HOSE CONNECTION ON WHICH THE PIPE THREAD IS LOCATED. SELECT REPLY CODE 10AJ91 BWYJJ 04DIAMETER,CONNECTION,HOSE HOSE CONNECTION DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOSE CONNECTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BWYKD 19FACILITY,PUMPING PUMPING FACILITY AN INDICATION OF THE PUMPING FACILITY(IES) PROVIDED. SELECT REPLY CODE 10AC55 BWYLD 18TYPE,STIRRER STIRRER TYPE INDICATES THE TYPE OF STIRRER PROVIDED. SELECT REPLY CODE 10AK54 BWYMA 12QUANTITY,STIRRER STIRRER QUANTITY THE NUMBER OF STIRRERS PROVIDED. 1A MODE REPLY 0 BWYNJ 13THREAD QUANTITY,END,PLAY PIPE DISCHARGE PLAY PIPE DISCHARGE END THREAD QUANTITY A MEASUREMENT OF THE NUMBER OF THREADS ON THE PLAY PIPE DISCHARGE END,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1D AND 1B MODE REPLY11AB39 BWYPD 13THREAD SERIES DESIGNATOR,END,PLAY PIPE DISCHARGE PLAY PIPE DISCHARGE END THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF PLAY PIPE DISCHARGE END THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 BWYQD /D/ 07CARRIER,TIP,INTEGRAL INTEGRAL TIP CARRIER AN INDICATION OF WHETHER OR NOT AN INTEGRAL TIP CARRIER IS INCLUDED. SELECT REPLY CODE 10AA49 BWYRD 18TYPE,DEVICE,SHUTOFF SHUTOFF DEVICE TYPE INDICATES THE TYPE OF DEVICE USED FOR SHUTOFF. SELECT REPLY CODE 10AK54 BWYSD 13THREAD LOCATION,CONNECTION,HOSE HOSE CONNECTION THREAD LOCATION THE PORTION(S) OF THE HOSE CONNECTION ON WHICH THE THREAD(S) IS LOCATED. SELECT REPLY CODE 10AJ91 BWYTJ 04THREAD DIAMETER,CONNECTION,HOSE HOSE CONNECTION THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE HOSE CONNECTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BWYWJ 13THREAD QUANTITY,CONNECTION,HOSE HOSE CONNECTION THREAD QUANTITY A MEASUREMENT OF THE NUMBER OF THREADS ON THE HOSE CONNECTION,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1D AND 1B MODE REPLY11AB39 BWYXD 13THREAD SERIES DESIGNATOR,CONNECTION,HOSE HOSE CONNECTION THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF HOSE CONNECTION THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 BWYYD /D/ 07OUTLET,BODY,THREADED THREADED BODY OUTLET AN INDICATION OF WHETHER OR NOT A THREADED BODY OUTLET IS INCLUDED. SELECT REPLY CODE 10AA49 BWYZD /D/ 07TIP,REMOVABLE REMOVABLE TIP AN INDICATION OF WHETHER OR NOT A REMOVABLE TIP IS INCLUDED. SELECT REPLY CODE 10AA49 BWZBD 18TYPE,DISCHARGE DISCHARGE TYPE INDICATES THE TYPE OF DISCHARGE. SELECT REPLY CODE 10AK54 BWZCJ 04DIAMETER,DISCHARGE DISCHARGE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DISCHARGE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BWZDD /D/ 07FEATURE,THREADED,DISCHARGE END DISCHARGE END THREADED FEATURE AN INDICATION OF WHETHER OR NOT THE DISCHARGE END INCLUDES A THREADED FEATURE. SELECT REPLY CODE 10AA49 BWZFD 13THREAD LOCATION,END,DISCHARGE DISCHARGE END THREAD LOCATION INDICATES THE PORTION(S) OF THE DISCHARGE END ON WHICH THE THREAD(S) IS LOCATED. SELECT REPLY CODE 10AJ91 BWZGJ /D/ 13THREAD DIAMETER,END,DISCHARGE DISCHARGE END THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE DISCHARGE END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BWZHJ /D/ 13THREAD QUANTITY,END,DISCHARGE DISCHARGE END THREAD QUANTITY A MEASUREMENT OF THE NUMBER OF THREADS ON THE DISCHARGE END,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1D AND 1B MODE REPLY11AB39 BWZJD /D/ 13THREAD SERIES DESIGNATOR,END,DISCHARGE DISCHARGE END THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF DISCHARGE END THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 BWZKD /D/ 07BUMPER,RUBBER RUBBER BUMPER AN INDICATION OF WHETHER OR NOT A RUBBER BUMPER IS INCLUDED. SELECT REPLY CODE 10AA49 BWZLD 18TYPE,CONNECTION,INLET END INLET END CONNECTION TYPE INDICATES THE TYPE OF INLET END CONNECTION. SELECT REPLY CODE 10AB76 BWZMJ 13THREAD DIAMETER,END,INLET INLET END THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE INLET END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BWZNJ 13THREAD QUANTITY,END,INLET INLET END THREAD QUANTITY A MEASUREMENT OF THE NUMBER OF THREADS ON THE INLET END,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1D AND 1B MODE REPLY11AB39 BWZPD 13THREAD SERIES DESIGNATOR,END,INLET INLET END THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF INLET END THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 BWZQA 12QUANTITY,ADAPTER ADAPTER QUANTITY THE NUMBER OF ADAPTERS PROVIDED. 1A MODE REPLY 0 BWZRD 13THREAD LOCATION,END,LARGE LARGE END THREAD LOCATION INDICATES THE PORTION(S) OF THE LARGE END ON WHICH THE THREAD(S) IS LOCATED. SELECT REPLY CODE 10AJ91 BWZSJ 13THREAD DIAMETER,END,LARGE LARGE END THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE LARGE END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BWZTJ 13THREAD QUANTITY,END,LARGE LARGE END THREAD QUANTITY A MEASUREMENT OF THE NUMBER OF THREADS ON THE LARGE END,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1D AND 1B MODE REPLY11AB39 BWZWD 13THREAD SERIES DESIGNATOR,END,LARGE LARGE END THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THE LARGE END THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 BWZXD 13THREAD LOCATION,END,SMALL SMALL END THREAD LOCATION INDICATES THE PORTION(S) OF THE SMALL END ON WHICH THE THREAD(S) IS LOCATED. SELECT REPLY CODE 10AJ91 BWZYJ 13THREAD DIAMETER,END,SMALL SMALL END THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE SMALL END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BWZZJ 13THREAD QUANTITY,END,SMALL SMALL END THREAD QUANTITY A MEASUREMENT OF THE NUMBER OF THREADS ON THE SMALL END,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1D AND 1B MODE REPLY11AB39 BXBBD 13THREAD SERIES DESIGNATOR,END,SMALL SMALL END THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF SMALL END THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 BXBCJ 04LENGTH,APPLICATOR APPLICATOR LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN APPLICATOR,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BXBDJ /D/ 04DIAMETER,DISCHARGE,ONE-PIECE TYPE ONE-PIECE TYPE DISCHARGE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ONE-PIECE TYPE DISCHARGE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BXBFJ 04LENGTH,OVERALL,ONE-PIECE TYPE BODY ONE-PIECE TYPE BODY OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF A ONE-PIECE TYPE BODY. 2D AND 1B MODE REPLY21AA051AC20 BXBGJ 04LENGTH,BODY,TIP TYPE,REMOVABLE REMOVABLE TIP TYPE BODY LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A REMOVABLE TIP TYPE BODY,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BXBHJ 10PRESSURE REQUIRED,WATER,MINIMUM MINIMUM WATER PRESSURE REQUIRED THE MINIMUM WATER PRESSURE REQUIRED TO OPERATE THE ITEM. 1D AND 1B MODE REPLY12AG67 BXBJD /D/ 07TUBE,PICK-UP PICK-UP TUBE AN INDICATION OF WHETHER OR NOT A PICK-UP TUBE IS INCLUDED. SELECT REPLY CODE 10AA49 BXBKD 07ADJUSTABILITY,TIP TIP ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE TIP IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BXBLD /D/ 13THREAD SERIES DESIGNATOR,CONNECTION,INLET INLET CONNECTION THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF INLET CONNECTION THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 BXBMJ /D/ 13THREAD DIAMETER,CONNECTION,INLET INLET CONNECTION THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE INLET CONNECTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BXBND /D/ 07FEATURE,GRIP,PISTOL PISTOL GRIP FEATURE AN INDICATION OF WHETHER OR NOT A PISTOL GRIP FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BXBPJ /D/ 04RADIUS,BODY,CONCAVE CONCAVE BODY RADIUS NONE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. 2D AND 1B MODE REPLY21AA051AC20 BXBQA /D/ 16STYLE DESIGNATOR,CONTOUR,OUTER OUTER CONTOUR STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE OUTER CONTOUR. 1A MODE REPLY 0 BXBRJ 04DIAMETER,INSIDE,HOLE HOLE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOLE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BXBSJ 04WIDTH,SPLIT SPLIT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SPLIT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BXBTJ 04LENGTH,PORTION,TAPERED TAPERED PORTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TAPERED PORTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BXBWG 04ANGLE,INCLUDED,TAPER TAPER INCLUDED ANGLE THE INCLUDED ANGLE OF THE TAPER. FULL TEXT WRITE-IN 0 BXBXJ /D/ 04LENGTH,CHAMFER,FLANGE FLANGE CHAMFER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FLANGE CHAMFER,IN DISTINCTION FROM WIDTH. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 BXBYB /D/ 04ANGLE IN DEG,CHAMFER,FLANGE FLANGE CHAMFER ANGLE IN DEG THE ANGLE OF THE FLANGE CHAMFER,EXPRESSED IN DEGREES. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 BXBZJ /D/ 04RADIUS,EDGE,FLANGE ROUNDED FLANGE ROUNDED EDGE RADIUS A MEASUREMENT OF THE LINE SEGMENT FROM THE CENTER TO THE MIDPOINT OF THE ROUNDED EDGE OF THE FLANGE. 2D AND 1B MODE REPLY21AA051AC20 BXCBH /D/ 09MATERIAL AND LOCATION,MEMBER,RIGID RIGID MEMBER MATERIAL AND LOCATION THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE RIGID MEMBER/S/ IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT,AND ITS LOCATION. 2D MODE REPLY 26AD093AJ91 BXCCH /D/ 17SURFACE TREATMENT AND LOCATION,MEMBER,RIGID RIGID MEMBER SURFACE TREATMENT AND LOCATION CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A RIGID MEMBER SURFACE,AND ITS LOCATION. 2D MODE REPLY 26AD093AJ91 BXCDJ 04DISTANCE FROM FLANGE TO END DISTANCE FROM FLANGE TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 BXCFJ 04LENGTH AT LARGE END OF BODY TAPER,STUD STUD LENGTH AT LARGE END OF BODY TAPER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXCGA 13THREAD SIZE AT LARGE END OF BODY TAPER THREAD SIZE AT LARGE END OF BODY TAPER NONE. 1A MODE REPLY 0 BXCHJ 04DISTANCE BETWEEN MOUNTING HOLE CENTERS,SHORTEST SHORTEST DISTANCE BETWEEN MOUNTING HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BXCJJ 04DISTANCE BETWEEN MOUNTING STUD CENTERS,SHORTEST SHORTEST DISTANCE BETWEEN MOUNTING STUD CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BXCKJ 04DISTANCE FROM MOUNTING SURFACE TO MOUNTING HOLE CENTER DISTANCE FROM MOUNTING SURFACE TO MOUNTING HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXCLJ 04DISTANCE FROM MOUNTING SURFACE TO MOUNTING HOLE CENTER,SHORTEST SHORTEST DISTANCE FROM MOUNTING SURFACE TO MOUNTING HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXCMJ 04WIDTH,MINOR,T SLOT T SLOT MINOR WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BXCNJ 04WIDTH,MAJOR,T SLOT T SLOT MAJOR WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BXCPJ 04HEIGHT,SLOT SLOT HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BXCQJ 04DIAMETER,HOLE,FLANGE MOUNTING FLANGE MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXCRJ 04HEIGHT,MEMBER,FLEXING FLEXING MEMBER HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BXCSJ 04DIAMETER,OUTSIDE,FLEXING MEMBER FLEXING MEMBER OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXCTG 10LOAD RATING AT SPECIFIED DEFLECTION,STATIC STATIC LOAD RATING AT SPECIFIED DEFLECTION THE RATED STATIC LOAD WHICH THE ITEM IS DESIGNED TO ACCOMMODATE AT A SPECIFIED DEFLECTION. FULL TEXT WRITE-IN 0 BXCWG /D/ 10RANGE,LOAD/FREQUENCY LOAD/FREQUENCY RANGE THE RATED LOAD THE ITEM IS DESIGNED TO ACCOMMODATE AT A SPECIFIED FREQUENCY RANGE. FULL TEXT WRITE-IN 0 BXCXJ /D/ 04DIAMETER,FLANGE,OUTSIDE/TOP OUTSIDE/TOP FLANGE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXCYJ 04DIAMETER,FLANGE,BOTTOM BOTTOM FLANGE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXCZJ 04DIAMETER,COUNTERBORE,FIRST FIRST COUNTERBORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXDBJ 04HEIGHT,CLEARANCE,INSIDE,CENTER CENTER INSIDE CLEARANCE HEIGHT A MEASUREMENT FROM FLOOR LEVEL TO CENTER CLEARANCE OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BXDCJ 04DISTANCE FROM CENTER OF BUMPER TO CENTER OF MOUNTING HOLE DISTANCE FROM CENTER OF BUMPER TO CENTER OF MOUNTING HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BXDDJ 04DIAMETER,COUNTERSINK,LARGEST LARGEST COUNTERSINK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXDFJ 04DIAMETER,COUNTERSINK,SMALLEST SMALLEST COUNTERSINK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXDGG /D/ 04SIZE AND TYPE,DEVICE,FASTENING FASTENING DEVICE SIZE AND TYPE DESIGNATES THE SIZE AND TYPE OF FASTENING DEVICE FURNISHED WITH THE ITEM. FULL TEXT WRITE-IN 0 BXDHJ 04LENGTH,SPAN SPAN LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SPAN,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BXDJD /D/ 07FEATURE,PANELED,PARTIALLY PARTIALLY PANELED FEATURE AN INDICATION OF WHETHER OR NOT A PARTIALLY PANELED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BXDKJ 04HEIGHT,CLEARANCE,INSIDE,SIDEWALL SIDEWALL INSIDE CLEARANCE HEIGHT A MEASUREMENT FROM THE FLOOR LEVEL TO THE TOP OF THE SIDEWALL. 2D AND 1B MODE REPLY21AA051AC20 BXDLD /D/ 09MATERIAL,FRAMING,ROOF ROOF FRAMING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ROOF FRAME IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXDMD /D/ 09MATERIAL,MEMBER,RESILIENT RESILIENT MEMBER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE RESILIENT MEMBER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXDND /D/ 09MATERIAL,ROOF ROOF MATERIAL THE ELEMENT,COMPOUND OR MIXTURE OF WHICH THE ROOF IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH USE IF ISAC TABLE 0143 IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 BXDPJ 04DISTANCE BETWEEN SECTIONS DISTANCE BETWEEN SECTIONS THE DISTANCE BETWEEN SECTIONS. 2D AND 1B MODE REPLY21AA051AC20 BXDQJ 04LENGTH,CHANNEL,GLASS GLASS CHANNEL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A GLASS CHANNEL,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BXDRJ 04WIDTH,INSIDE,LARGEST,GLASS CHANNEL GLASS CHANNEL LARGEST INSIDE WIDTH THE LARGEST INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE GLASS CHANNEL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BXDSJ 04DEPTH,CHANNEL,GLASS GLASS CHANNEL DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON A GLASS CHANNEL,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BXDTD /D/ 07STRIP,WEATHER,GLASS SEATING GLASS SEATING WEATHER STRIP AN INDICATION OF WHETHER OR NOT A GLASS SEATING WEATHER STRIP IS INCLUDED. SELECT REPLY CODE 10AA49 BXDWJ 04LENGTH FROM WEDGE CENTER TO END LENGTH FROM WEDGE CENTER TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 BXDXJ 04WIDTH,LARGEST,WEDGE WEDGE LARGEST WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BXDYB 04ANGLE IN DEG,TAPER,FIRST FIRST TAPER ANGLE IN DEG NONE. 1B MODE REPLY 0 BXDZB 04ANGLE IN DEG,TAPER,SECOND SECOND TAPER ANGLE IN DEG NONE. 1B MODE REPLY 0 BXFBJ /D/ 04DISTANCE ALONG LENGTH,MAJOR,HOLE CENTERS HOLE CENTERS MAJOR DISTANCE ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BXFCJ /D/ 04DISTANCE ALONG LENGTH,MINOR,HOLE CENTERS HOLE CENTERS MINOR DISTANCE ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BXFDA /D/ 16STYLE ARRANGEMENT,HOLE HOLE STYLE ARRANGEMENT THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HOLE ARRANGEMENT. 1A MODE REPLY 0 BXFFD /D/ 09MATERIAL,BLOCK BLOCK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BLOCK(S) IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXFGD /D/ 17SURFACE TREATMENT,BLOCK BLOCK SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE BLOCK SURFACE. SELECT REPLY CODE 10AD09 BXFHA 12QUANTITY,HOLE,STRAIGHT END MOUNTING STRAIGHT END MOUNTING HOLE QUANTITY NONE. 1A MODE REPLY 0 BXFJJ 04DIAMETER,HOLE,STRAIGHT END MOUNTING STRAIGHT END MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXFKA /D/ 12QUANTITY,HOLE,OFFSET END MOUNTING OFFSET END MOUNTING HOLE QUANTITY NONE. 1A MODE REPLY 0 BXFLJ /D/ 04DIAMETER,HOLE,OFFSET END MOUNTING OFFSET END MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXFMJ 04DISTANCE BETWEEN STRAIGHT END MOUNTING HOLES ALONG WIDTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN STRAIGHT END MOUNTING HOLES ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BXFNJ 04DISTANCE BETWEEN STRAIGHT END MOUNTING HOLES ALONG LENGTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN STRAIGHT END MOUNTING HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BXFPJ /D/ 04DISTANCE BETWEEN STRAIGHT END AND OFFSET END MOUNTING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN STRAIGHT END AND OFFSET END MOUNTING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 BXFQJ 04DISTANCE BETWEEN OFFSET END MOUNTING HOLES ALONG LENGTH,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN OFFSET END MOUNTING HOLES ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BXFRJ /D/ 04DISTANCE TO CENTER OF FIRST STRAIGHT END MOUNTING HOLE,INSIDE,STEP STEP INSIDE DISTANCE TO CENTER OF FIRST STRAIGHT END MOUNTING HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BXFSD /D/ 07DIMPLES,WELDING WELDING DIMPLES AN INDICATION OF WHETHER OR NOT WELDING DIMPLES ARE INCLUDED. SELECT REPLY CODE 10AA49 BXFTA 12QUANTITY,POINT,ATTACHING ATTACHING POINT QUANTITY THE NUMBER OF ATTACHING POINTS PROVIDED. 1A MODE REPLY 0 BXFWG 04SIZE,OPENING,INLET INLET OPENING SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE INLET OPENING. FULL TEXT WRITE-IN 0 BXFXA 19NUMBER,SCREEN,INLET INLET SCREEN NUMBER THE NUMBER BY WHICH THE SIZE OF THE INLET SCREEN IS IDENTIFIED. 1A MODE REPLY 0 BXFYG 04SIZE,OPENING,OUTLET OUTLET OPENING SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE OUTLET OPENING. FULL TEXT WRITE-IN 0 BXFZA 19AIRCRAFT FOR WHICH DESIGNED AIRCRAFT FOR WHICH DESIGNED AN INDICATION OF THE AIRCRAFT FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 BXGBA 12QUANTITY,PIECE PIECE QUANTITY THE NUMBER OF PIECES PROVIDED. 1A MODE REPLY 0 BXGCD /D/ 07PLUG,FILLER FILLER PLUG AN INDICATION OF WHETHER OR NOT A FILLER PLUG IS INCLUDED. SELECT REPLY CODE 10AA49 BXGDD /D/ 07TANK,FLUID,SIDE ATTACHED SIDE ATTACHED FLUID TANK AN INDICATION OF WHETHER OR NOT A SIDE ATTACHED FLUID TANK IS INCLUDED. SELECT REPLY CODE 10AA49 BXGFJ /D/ 04DISTANCE BETWEEN HOLE/STUD CENTERS,HORIZONTAL HORIZONTAL DISTANCE BETWEEN HOLE/STUD CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BXGGJ /D/ 04DISTANCE BETWEEN UPPER HOLE/STUD CENTERS,HORIZONTAL HORIZONTAL DISTANCE BETWEEN UPPER HOLE/STUD CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BXGHJ /D/ 04DISTANCE BETWEEN LOWER HOLE/STUD CENTERS,HORIZONTAL HORIZONTAL DISTANCE BETWEEN LOWER HOLE/STUD CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BXGJJ /D/ 04DISTANCE FROM VERTICAL HOLE/STUD CENTERLINE TO LEFT HOLE/STUD CENTER DISTANCE FROM VERTICAL HOLE/STUD CENTERLINE TO LEFT HOLE/STUD CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXGKJ /D/ 04DISTANCE FROM HORIZONTAL HOLE/STUD CENTER TO UPPER HOLE/STUD CENTER DISTANCE FROM HORIZONTAL HOLE/STUD CENTER TO UPPER HOLE/STUD CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXGLJ /D/ 04DISTANCE BETWEEN LEFT UPPER HOLE/STUD CENTERLINE AND LEFT LOWER HOLE/STUD CENTERLINE,HORIZONTAL HORIZONTAL DISTANCE BETWEEN LEFT UPPER HOLE/STUD CENTERLINE AND LEFT LOWER HOLE/STUD CENTERLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 BXGMA /D/ 16STYLE,LEVER LEVER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LEVER. 1A MODE REPLY 0 BXGNJ /D/ 04THICKNESS,END,CONNECTION CONNECTION END THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BXGPJ 04DIAMETER,STIRRER STIRRER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE STIRRER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BXGQD /D/ 07NOZZLE NOZZLE AN INDICATION OF WHETHER OR NOT A NOZZLE IS INCLUDED. SELECT REPLY CODE 10AA49 BXGRJ 10DISPLACEMENT RATING DISPLACEMENT RATING THE DISPLACEMENT BY VOLUME OF THE ITEM. 2D AND 1B MODE REPLY22AG671AC20 BXGSJ 04DIAMETER ACCOMMODATED,PROPELLER,MAXIMUM MAXIMUM PROPELLER DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR A PROPELLER,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BXGTD 11METHOD,OPERATION,AGITATOR AGITATOR OPERATION METHOD THE MEANS BY WHICH THE AGITATOR IS OPERATED. SELECT REPLY CODE 10AC58 BXGWD /D/ 18TYPE,CASE,MOTOR MOTOR CASE TYPE INDICATES THE TYPE OF MOTOR CASE PROVIDED. SELECT REPLY CODE 10AJ95 BXGXJ 10CONSUMPTION,AIR,MAXIMUM MAXIMUM AIR CONSUMPTION THE MAXIMUM AIR THAT IS CONSUMED BY THE ITEM. 1D AND 1B MODE REPLY12AG67 BXGYB 10SPEED IN RPM,MAXIMUM,PADDLE PADDLE MAXIMUM SPEED IN RPM THE MAXIMUM SPEED OF THE PADDLE/S/,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 BXGZG 13SCREW THREAD SERIES DESIGNATOR,OUTLET OUTLET SCREW THREAD SERIES DESIGNATOR A DESIGNATOR DISTINGUISHING ONE GROUP OF OUTLET SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. FULL TEXT WRITE-IN 0 BXHBD 13SCREW THREAD SERIES DESIGNATOR,INLET INLET SCREW THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF INLET SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 BXHCD /D/ 09MATERIAL,LID LID MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LID IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXHDD /D/ 17SURFACE TREATMENT,LID LID SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE LID SURFACE. SELECT REPLY CODE 10AD09 BXHFD 11METHOD,SECURING,LID LID SECURING METHOD THE MEANS BY WHICH THE LID IS SECURED. SELECT REPLY CODE 10AM39 BXHGJ 04DIAMETER,HOSE HOSE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOSE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BXHHD /D/ 07SHAFT,FLEXIBLE FLEXIBLE SHAFT AN INDICATION OF WHETHER OR NOT A FLEXIBLE SHAFT IS INCLUDED. SELECT REPLY CODE 10AA49 BXHJD 19LIQUID FOR WHICH DESIGNED LIQUID FOR WHICH DESIGNED THE LIQUID FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AB75 BXHKD 14SHAPE,COMPARTMENT COMPARTMENT SHAPE THE PHYSICAL CONFIGURATION OF THE COMPARTMENT. SELECT REPLY CODE 10AD07 BXHLD /D/ 17SURFACE TREATMENT,INSIDE,COMPARTMENT COMPARTMENT INSIDE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL.OR MILD MECHANICAL PROCESS WHICH PROTECTS THE COMPARTMENT INSIDE SURFACE. SELECT REPLY CODE 10AD09 BXHMD /D/ 07PROVISION,SUSPENSION,MATERIAL MATERIAL SUSPENSION PROVISION AN INDICATION OF WHETHER OR NOT A PROVISION FOR THE SUSPENSION OF MATERIAL(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BXHNA /D/ 12QUANTITY,DRAINBOARD DRAINBOARD QUANTITY THE NUMBER OF DRAINBOARDS PROVIDED. 1A MODE REPLY 0 BXHPD /D/ 07FEATURE,SAFETY,FUSIBLE LINK FUSIBLE LINK SAFETY FEATURE AN INDICATION OF WHETHER OR NOT A FUSIBLE LINK SAFETY FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BXHRJ 04DIAMETER,OUTSIDE,CABLE CABLE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CABLE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BXHSJ 04LENGTH ACCOMMODATED,SECTION,CABLE CABLE SECTION LENGTH ACCOMMODATED A MEASUREMENT OF THE LONGEST DIMENSION OF THE CABLE SECTION THE ITEM WILL ACCOMMODATE. 2D AND 1B MODE REPLY21AA051AC20 BXHTD /D/ 07FEATURE,CENTER,ENLARGED ENLARGED CENTER FEATURE AN INDICATION OF WHETHER OR NOT AN ENLARGED CENTER FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BXHWD 07SOURCE,STEAM,OUTSIDE OUTSIDE STEAM SOURCE AN INDICATION OF WHETHER OR NOT AN OUTSIDE STEAM SOURCE IS REQUIRED. SELECT REPLY CODE 10AE40 BXHXJ 10PRESSURE RATING,STEAM STEAM PRESSURE RATING THE AMOUNT OF STEAM PRESSURE FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY22AG671AC20 BXHYD 07SOURCE,WATER,OUTSIDE OUTSIDE WATER SOURCE AN INDICATION OF WHETHER OR NOT AN OUTSIDE WATER SOURCE IS REQUIRED. SELECT REPLY CODE 10AE40 BXHZJ 10PRESSURE RATING,JET,CLEANING SOLUTION,MAXIMUM MAXIMUM CLEANING SOLUTION JET PRESSURE RATING THE MAXIMUM AMOUNT OF CLEANING SOLUTION PRESSURE FOR WHICH THE JET IS RATED. 1D AND 1B MODE REPLY12AG67 BXJBJ 10DISCHARGE RATE,MAXIMUM,CLEANING SOLUTION CLEANING SOLUTION MAXIMUM DISCHARGE RATE THE MAXIMUM RATE OF CLEANING SOLUTION THE ITEM IS DESIGNED TO DISCHARGE. 1D AND 1B MODE REPLY12AG67 BXJCJ 10PRESSURE RATING,JET,LIQUID,MAXIMUM MAXIMUM LIQUID JET PRESSURE RATING THE MAXIMUM AMOUNT OF LIQUID PRESSURE FOR WHICH THE JET IS RATED. 1D AND 1B MODE REPLY12AG67 BXJDJ 10DISCHARGE RATE,LIQUID,MAXIMUM MAXIMUM LIQUID DISCHARGE RATE THE MAXIMUM RATE OF LIQUID THE ITEM IS DESIGNED TO DISCHARGE. 1D AND 1B MODE REPLY12AG67 BXJFA 12QUANTITY,GUN,CLEANING CLEANING GUN QUANTITY THE NUMBER OF CLEANING GUNS PROVIDED. 1A MODE REPLY 0 BXJGD 07ADJUSTABILITY,NOZZLE NOZZLE ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE NOZZLE IS ADJUSTABLE. SELECT REPLY CODE 10AB00 BXJJA 12QUANTITY,TANK,STORAGE STORAGE TANK QUANTITY THE NUMBER OF STORAGE TANKS PROVIDED. 1A MODE REPLY 0 BXJKD 19MATERIAL,STORED STORED MATERIAL AN INDICATION OF THE MATERIAL THAT IS STORED. SELECT REPLY CODE 10AN44 BXJLD /D/ 07FEATURE,SUPPORT,RETRACTABLE RETRACTABLE SUPPORT FEATURE AN INDICATION OF WHETHER OR NOT A RETRACTABLE SUPPORT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BXJMJ 04DIAMETER,WHEEL,CASTER CASTER WHEEL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CASTER WHEEL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BXJND 18TYPE,TIRE,CASTER CASTER TIRE TYPE INDICATES THE TYPE OF TIRE PROVIDED ON THE CASTER(S). SELECT REPLY CODE 10AH67 BXJPJ 04DIAMETER ACCOMMODATED,ARBOR,SAW SAW ARBOR DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR A SAW ARBOR,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BXJQJ 10ADJUSTMENT,VERTICAL,ARBOR ARBOR VERTICAL ADJUSTMENT A MEASUREMENT OF THE VERTICAL ADJUSTMENT OF THE ARBOR. 2D AND 1B MODE REPLY21AA051AC20 BXJRB 04ANGLE IN DEG,TILT,ARBOR ARBOR TILT ANGLE IN DEG THE TILT ANGLE OF THE ARBOR,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BXJSJ 04LENGTH,ARBOR ARBOR LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ARBOR,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BXJTD 18TYPE,SPRING,FLEXIBLE FLEXIBLE SPRING TYPE INDICATES THE TYPE OF FLEXIBLE SPRING PROVIDED. SELECT REPLY CODE 10AK54 BXJWJ 04DIAMETER,OVERALL,SPRING SPRING OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE CROSS-SECTIONAL PLANE OF THE SPRING. 2D AND 1B MODE REPLY21AA051AC20 BXJXJ 04WIDTH,OVERALL,SPRING SPRING OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A SPRING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BXJYL 16STYLE,IMPLEMENT,DIGGING DIGGING IMPLEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE DIGGING IMPLEMENT(S). 1L MODE REPLY 0 BXJZD /D/ 07KNIFE,BEVELING/GROOVING BEVELING/GROOVING KNIFE AN INDICATION OF WHETHER OR NOT A BEVELING AND/OR GROOVING KNIFE/VES/ IS PROVIDED. SELECT REPLY CODE 10AB22 BXKBD 18TYPE,CONSTRUCTION,BLADE BLADE CONSTRUCTION TYPE INDICATES THE TYPE OF CONSTRUCTION OF THE BLADE. SELECT REPLY CODE 10AK54 BXKCD 14SHAPE,ORIFICE ORIFICE SHAPE THE PHYSICAL CONFIGURATION OF THE ORIFICE. SELECT REPLY CODE 10AD07 BXKDJ 04LENGTH,SLOT,ORIFICE ORIFICE SLOT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ORIFICE SLOT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BXKFJ 04WIDTH,SLOT,ORIFICE ORIFICE SLOT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ORIFICE SLOT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BXKGJ /D/ 04SIZE,ORIFICE,TRIANGULAR TRIANGULAR ORIFICE SIZE DESIGNATES THE SIZE BY WHICH A TRIANGULAR ORIFICE IS IDENTIFIED. 1D AND 1B MODE REPLY11AA05 BXKHD /D/ 07HOOK,GROPING GROPING HOOK AN INDICATION OF WHETHER OR NOT A GROPING HOOK IS PROVIDED. SELECT REPLY CODE 10AB22 BXKJD /D/ 18TYPE FOR WHICH DESIGNED,PIPE PIPE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF PIPE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BXKKD /D/ 07ROLLER,CONVERSION CONVERSION ROLLER AN INDICATION OF WHETHER OR NOT A CONVERSION ROLLER(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BXKLD 18TYPE,MECHANISM,CUTTING CUTTING MECHANISM TYPE INDICATES THE TYPE OF CUTTING MECHANISM PROVIDED. SELECT REPLY CODE 10AC82 BXKMD /D/ 18TYPE FOR WHICH DESIGNED,CABLE CABLE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF CABLE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BXKPD 13THREAD LOCATION,SHANK SHANK THREAD LOCATION INDICATES THE THREAD LOCATION OF THE SHANK. SELECT REPLY CODE 10AJ91 BXKQJ T04DIAMETER RANGE,CUTTING,CIRCLE CIRCLE CUTTING DIAMETER RANGE THE MINIMUM AND MAXIMUM LENGTHS OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CIRCLE THE ITEM IS CAPABLE OF CUTTING,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1F MODE REPLY11AA05 BXKRJ T04DIAMETER RANGE ACCOMMODATED,GAGE,TUBULAR TUBULAR GAGE DIAMETER RANGE ACCOMMODATED THE MINIMUM AND MAXIMUM LENGTHS OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION OF A TUBULAR GAGE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1F MODE REPLY11AA05 BXKSD /D/ 07PIVOT,DRILL DRILL PIVOT AN INDICATION OF WHETHER OR NOT A DRILL PIVOT IS PROVIDED. SELECT REPLY CODE 10AB22 BXKTD /D/ 07PIVOT,RETRACTABLE RETRACTABLE PIVOT AN INDICATION OF WHETHER OR NOT A RETRACTABLE PIVOT IS PROVIDED. SELECT REPLY CODE 10AB22 BXKWD /D/ 07BOARD,CUTTING CUTTING BOARD AN INDICATION OF WHETHER OR NOT A CUTTING BOARD IS PROVIDED. SELECT REPLY CODE 10AB22 BXKXD 18TYPE,END,CUTTING CUTTING END TYPE INDICATES THE TYPE OF CUTTING END PROVIDED. SELECT REPLY CODE 10AK84 BXKYD /D/ 07TURRET,END,CUTTING CUTTING END TURRET AN INDICATION OF WHETHER OR NOT A CUTTING END TURRET IS PROVIDED. SELECT REPLY CODE 10AB22 BXKZA 12QUANTITY,WHEEL,CUTTING,ADDITIONAL ADDITIONAL CUTTING WHEEL QUANTITY THE NUMBER OF ADDITIONAL CUTTING WHEELS PROVIDED. 1A MODE REPLY 0 BXLBD /D/ 07FEATURE,CUTOFF,CLOSE FLARE CLOSE FLARE CUTOFF FEATURE AN INDICATION OF WHETHER OR NOT A CLOSE FLARE CUTOFF FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BXLCD /D/ 07TOOL,DEBURRING DEBURRING TOOL AN INDICATION OF WHETHER OR NOT A DEBURRING TOOL IS PROVIDED. SELECT REPLY CODE 10AB22 BXLDD 18TYPE,PATTERN PATTERN TYPE INDICATES THE TYPE OF PATTERN PROVIDED. SELECT REPLY CODE 10AK54 BXLFD /D/ 07FEATURE,USAGE,MULTIPLE SIZE MULTIPLE SIZE USAGE FEATURE AN INDICATION OF WHETHER OR NOT A MULTIPLE SIZE USAGE FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BXLGJ 04THICKNESS FOR WHICH DESIGNED,WALL,TUBING TUBING WALL THICKNESS FOR WHICH DESIGNED A MEASUREMENT OF THE SMALLEST DIMENSION OF THE TUBING WALL FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BXLHJ 04DISTANCE,HEEL TO POINT HEEL TO POINT DISTANCE THE DISTANCE FROM THE HEEL TO THE POINT OF AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 BXLJJ 04THICKNESS,LARGEST LARGEST THICKNESS THE LONGEST MEASUREMENT OF THE SMALLEST DIMENSION OF THE ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 BXLKD 18TYPE,CUT,FACE FACE CUT TYPE INDICATES THE TYPE OF FACE CUT PROVIDED. SELECT REPLY CODE 10AL18 BXLLD 18TYPE,CUT,EDGE EDGE CUT TYPE INDICATES THE TYPE OF EDGE CUT PROVIDED. SELECT REPLY CODE 10AL18 BXLMD 18TYPE,CUT,COARSE COARSE CUT TYPE INDICATES THE TYPE OF COARSE CUT OF THE ITEM. SELECT REPLY CODE 10AL18 BXLNA 12QUANTITY,FILE FILE QUANTITY THE NUMBER OF FILES PROVIDED. 1A MODE REPLY 0 BXLPJ /D/ 04DIAMETER,BORE,VACUUM LINE PLUG VACUUM LINE PLUG BORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A VACUUM LINE PLUG BORE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BXLQA /D/ 12QUANTITY,PLUG,VACUUM LINE VACUUM LINE PLUG QUANTITY THE NUMBER OF VACUUM LINE PLUGS PROVIDED. 1A MODE REPLY 0 BXLRJ /D/ 04DIAMETER,OUTSIDE,CONDUCTOR CONDUCTOR OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CONDUCTOR,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BXLSJ /D/ 04DIAMETER,OVERALL,FUSE FUSE OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE CIRCULAR CROSS-SECTIONAL PLANE OF THE FUSE. 2D AND 1B MODE REPLY21AA051AC20 BXLTJ /D/ 04LENGTH,OVERALL,FUSE FUSE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE FUSE. 2D AND 1B MODE REPLY21AA051AC20 BXLWD 18TYPE,CONNECTION,MOUTH MOUTH CONNECTION TYPE INDICATES THE TYPE OF MOUTH CONNECTION PROVIDED. SELECT REPLY CODE 10AM35 BXLXD 18TYPE,CONNECTION,STEM STEM CONNECTION TYPE INDICATES THE TYPE OF STEM CONNECTION PROVIDED. SELECT REPLY CODE 10AM35 BXLYJ /D/ 04DIAMETER,CONNECTOR CONNECTOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CONNECTOR,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BXLZD /D/ 09MATERIAL,CONNECTOR CONNECTOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CONNECTOR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXMBD /D/ 19POROSITY,DISK DISK POROSITY AN INDICATION OF THE POROSITY OF THE DISK. SELECT REPLY CODE 10AF67 BXMCD /D/ 07CONDUCTOR CONDUCTOR AN INDICATION OF WHETHER OR NOT A CONDUCTOR IS INCLUDED. SELECT REPLY CODE 10AA49 BXMDD /D/ 07ARM,SIDE SIDE ARM AN INDICATION OF WHETHER OR NOT A SIDE ARM IS INCLUDED. SELECT REPLY CODE 10AA49 BXMFJ /D/ 04DIAMETER,OUTSIDE,SIDE ARM SIDE ARM OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SIDE ARM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BXMGD 14SHAPE,TUBE,OUTLET OUTLET TUBE SHAPE THE PHYSICAL CONFIGURATION OF THE OUTLET TUBE. SELECT REPLY CODE 10AD07 BXMHD /D/ 09MATERIAL,VALVE VALVE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE VALVE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXMJD /D/ 07WASHER WASHER AN INDICATION OF WHETHER OR NOT A WASHER IS INCLUDED. SELECT REPLY CODE 10AA49 BXMKD /D/ 07RACK,PIPETTE PIPETTE RACK AN INDICATION OF WHETHER OR NOT A PIPETTE RACK IS INCLUDED. SELECT REPLY CODE 10AA49 BXMLJ 04DEPTH,OVERALL,CHAMBER CHAMBER OVERALL DEPTH AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF A CHAMBER,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 BXMMJ 04DIAMETER,OVERALL,CHAMBER CHAMBER OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE CIRCULAR CROSS-SECTIONAL PLANE OF THE CHAMBER. 2D AND 1B MODE REPLY21AA051AC20 BXMNJ 04DIAMETER,OVERALL,OUTLET NIPPLE OUTLET NIPPLE OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE CROSS-SECTIONAL PLANE OF THE OUTLET NIPPLE. 2D AND 1B MODE REPLY21AA051AC20 BXMPD 18TYPE,CONNECTION,OUTLET NIPPLE OUTLET NIPPLE CONNECTION TYPE INDICATES THE TYPE OF OUTLET NIPPLE CONNECTION PROVIDED. SELECT REPLY CODE 10AM35 BXMQJ 04DIAMETER,OVERALL,INLET NIPPLE INLET NIPPLE OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE CROSS-SECTIONAL PLANE OF THE INLET NIPPLE. 2D AND 1B MODE REPLY21AA051AC20 BXMRD 18TYPE,CONNECTION,INLET NIPPLE INLET NIPPLE CONNECTION TYPE INDICATES THE TYPE OF INLET NIPPLE CONNECTION PROVIDED. SELECT REPLY CODE 10AM35 BXMSJ /D/ 10CAPACITY,BOTTLE,RESERVOIR RESERVOIR BOTTLE CAPACITY THE CAPACITY OF THE RESERVOIR BOTTLE(S). 1D AND 1B MODE REPLY12AG67 BXMTD /D/ 18TYPE,PIPETTE PIPETTE TYPE INDICATES THE TYPE OF PIPETTE(S) PROVIDED. SELECT REPLY CODE 10AM54 BXMWD /D/ 07TUBE,OVERFLOW OVERFLOW TUBE AN INDICATION OF WHETHER OR NOT AN OVERFLOW TUBE IS INCLUDED. SELECT REPLY CODE 10AA49 BXMXG /D/ 11METHOD,SECURING,PIPETTE TO RESERVOIR PIPETTE TO RESERVOIR SECURING METHOD THE MEANS USED TO ATTACH THE PIPETTE TO THE RESERVOIR. FULL TEXT WRITE-IN 0 BXMYD /D/ 07TOP,CONSTRICTED CONSTRICTED TOP AN INDICATION OF WHETHER OR NOT A CONSTRICTED TOP IS INCLUDED. SELECT REPLY CODE 10AA49 BXMZD /D/ 07BULB,RUBBER RUBBER BULB AN INDICATION OF WHETHER OR NOT A RUBBER BULB IS INCLUDED. SELECT REPLY CODE 10AA49 BXNBA /D/ 16STYLE,ROD,STIRRING STIRRING ROD STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE STIRRING ROD. 1A MODE REPLY 0 BXNCD /D/ 07BLADE,ROD,STIRRING,DETACHABLE DETACHABLE STIRRING ROD BLADE AN INDICATION OF WHETHER OR NOT A DETACHABLE STIRRING ROD BLADE IS INCLUDED. SELECT REPLY CODE 10AA49 BXNDD /D/ 07MAGNET,STIRRING STIRRING MAGNET AN INDICATION OF WHETHER OR NOT A STIRRING MAGNET IS INCLUDED. SELECT REPLY CODE 10AA49 BXNFA 12QUANTITY,BAR,TOTAL TOTAL BAR QUANTITY THE TOTAL NUMBER OF BARS PROVIDED. 1A MODE REPLY 0 BXNGA 12QUANTITY,BAR,INDIVIDUAL INDIVIDUAL BAR QUANTITY THE NUMBER OF INDIVIDUAL BARS PROVIDED. 1A MODE REPLY 0 BXNHJ 04LENGTH,OVERALL,BAR BAR OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BAR. 1D AND 1B MODE REPLY11AA05 BXNJJ 04DIAMETER,BODY,BAR BAR BODY DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CIRCULAR CROSS SECTION OF THE BAR BODY,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BXNKD /D/ 07RING,PADDLE PADDLE RING AN INDICATION OF WHETHER OR NOT A PADDLE RING IS INCLUDED. SELECT REPLY CODE 10AA49 BXNLD 18TYPE FOR WHICH DESIGNED,EXTINGUISHER EXTINGUISHER TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF EXTINGUISHER FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AG54 BXNMA 12QUANTITY,SPLINE,SHAFT FACILITY SHAFT FACILITY SPLINE QUANTITY NONE. 1A MODE REPLY 0 BXNNG /D/ 13THREAD SIZE DESIGNATOR,FACILITY,SHAFT SHAFT FACILITY THREAD SIZE DESIGNATOR NONE. FULL TEXT WRITE-IN 0 BXNPJ 04DISTANCE BETWEEN STAKES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN STAKES THE CENTER TO CENTER DISTANCE BETWEEN STAKES. 2D AND 1B MODE REPLY21AA051AC20 BXNQJ 04DIAMETER,OPENING,OUTLET DISCHARGE OUTLET DISCHARGE OPENING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTLET DISCHARGE OPENING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BXNRD /D/ 07FEATURE,OUTLET,THREADED THREADED OUTLET FEATURE AN INDICATION OF WHETHER OR NOT A THREADED OUTLET FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BXNSD /D/ 07BUMPER,RUBBER,OUTLET OUTLET RUBBER BUMPER AN INDICATION OF WHETHER OR NOT AN OUTLET RUBBER BUMPER IS INCLUDED. SELECT REPLY CODE 10AA49 BXNTA 12QUANTITY,TERMINATION TERMINATION QUANTITY THE NUMBER OF TERMINATIONS PROVIDED. 1A MODE REPLY 0 BXNWJ 10SETTING,TEMP,MINIMUM,FIRE ALARM FIRE ALARM MINIMUM TEMP SETTING THE MINIMUM TEMPERATURE AT WHICH THE ITEM WILL ACTUATE THE FIRE ALARM. 1D AND 1B MODE REPLY11AB36 BXNXG 10CAPACITY AT SPECIFIED PRESSURE RATING,FLOW FLOW CAPACITY AT SPECIFIED PRESSURE RATING THE RATED AMOUNT OF FLOW AT A SPECIFIC RATED PRESSURE. FULL TEXT WRITE-IN 0 BXNYJ 04DIAMETER,CYLINDER,UPPER UPPER CYLINDER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE UPPER CYLINDER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BXNZJ 04DIAMETER,CYLINDER,LOWER LOWER CYLINDER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LOWER CYLINDER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BXPBJ 04DISTANCE,LIFT,PISTON PISTON LIFT DISTANCE THE VERTICAL DISTANCE THE PISTON WILL LIFT. 2D AND 1B MODE REPLY21AA051AC20 BXPCD /D/ 07BOX,STUFFING STUFFING BOX AN INDICATION OF WHETHER OR NOT A STUFFING BOX IS INCLUDED. SELECT REPLY CODE 10AA49 BXPDA /D/ 16STYLE,HOLDER,BLADE BLADE HOLDER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BLADE HOLDER. 1A MODE REPLY 0 BXPFJ 04LENGTH,INSIDE,BLADE HOLDER BLADE HOLDER INSIDE LENGTH A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF THE BLADE HOLDER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BXPGD /D/ 07HOLDER,HANDLE HANDLE HOLDER AN INDICATION OF WHETHER OR NOT A HANDLE HOLDER IS INCLUDED. SELECT REPLY CODE 10AA49 BXPHD /D/ 07GUARD,HEAD,PICK PICK HEAD GUARD AN INDICATION OF WHETHER OR NOT A PICK HEAD GUARD IS INCLUDED. SELECT REPLY CODE 10AA49 BXPJJ 04SIZE,CONNECTION CONNECTION SIZE DESIGNATES THE SIZE OF THE CONNECTION. 1D AND 1B MODE REPLY11AA05 BXPKJ 04SIZE,DRAIN DRAIN SIZE DESIGNATES THE SIZE OF THE DRAIN. 1D AND 1B MODE REPLY11AA05 BXPLJ /D/ 04SIZE,PIPE,AIR INLET IRON AIR INLET IRON PIPE SIZE DESIGNATES THE IRON PIPE SIZE FOR WHICH THE AIR INLET IS DESIGNED. 1D AND 1B MODE REPLY11AA05 BXPMJ 10PROTECTION,TEMP,MINIMUM MINIMUM TEMP PROTECTION AN INDICATION OF THE LOWEST TEMPERATURE FOR WHICH THE ITEM IS PROTECTED. 1D AND 1B MODE REPLY11AB36 BXPND /D/ 18TYPE FOR WHICH DESIGNED,GENERATOR GENERATOR TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF GENERATOR FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BXPPD /D/ 18TYPE,POWDER POWDER TYPE INDICATES THE TYPE OF POWDER PROVIDED. SELECT REPLY CODE 10AG34 BXPQJ 10VOLUME,SOLUTION,FOAM,MINIMUM MINIMUM FOAM SOLUTION VOLUME AN INDICATION OF THE MINIMUM AMOUNT OF FOAM PRODUCED PER EQUAL AMOUNT OF SOLUTION. 1D AND 1B MODE REPLY12AG67 BXPRD /D/ 09MATERIAL,COVERING,BODY BODY COVERING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BODY COVERING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXPSD /D/ 07HOOK,LADDER LADDER HOOK AN INDICATION OF WHETHER OR NOT A LADDER HOOK IS INCLUDED. SELECT REPLY CODE 10AA49 BXPTJ 04THREAD DIAMETER,INLET INLET THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE INLET,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BXPWJ 13THREAD QUANTITY,INLET INLET THREAD QUANTITY A MEASUREMENT OF THE NUMBER OF THREADS ON THE INLET,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREADED AXIS. 1D AND 1B MODE REPLY11AB39 BXPYD 18TYPE,FACILITY,WRENCHING,INLET INLET WRENCHING FACILITY TYPE INDICATES THE TYPE OF WRENCHING FACILITY USED TO ASSEMBLE OR DISASSEMBLE THE INLET. SELECT REPLY CODE 10AL17 BXPZJ 04THREAD DIAMETER,OUTLET OUTLET THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE OUTLET,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BXQBJ 13THREAD QUANTITY,OUTLET OUTLET THREAD QUANTITY A MEASUREMENT OF THE NUMBER OF THREADS ON THE OUTLET,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1D AND 1B MODE REPLY11AB39 BXQDD /D/ 18TYPE,FACILITY,WRENCHING,OUTLET OUTLET WRENCHING FACILITY TYPE INDICATES THE TYPE OF WRENCHING FACILITY USED TO ASSEMBLE OR DISASSEMBLE THE OUTLET. SELECT REPLY CODE 10AL17 BXQFJ /D/ 10WEIGHT,NET NET WEIGHT THE WEIGHT OF AN ITEM EXCLUDING ANY EXTRA EQUIPMENT. 2D AND 1B MODE REPLY22AG671AC20 BXQGD /D/ 07CUSHION CUSHION AN INDICATION OF WHETHER OR NOT A CUSHION(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BXQHD /D/ 09MATERIAL,STRIP,BONDING BONDING STRIP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BONDING STRIP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXQJD /D/ 07PAD,MOUNTING MOUNTING PAD AN INDICATION OF WHETHER OR NOT A MOUNTING PAD(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BXQKA /D/ 16STYLE DESIGNATOR,BUCKLE BUCKLE STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BUCKLE(S). 1A MODE REPLY 0 BXQLJ 04WIDTH,ACCOMMODATION,STRAP STRAP ACCOMMODATION WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BXQMD /D/ 09MATERIAL,BUCKLE BUCKLE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BUCKLE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXQND /D/ 17SURFACE TREATMENT,BUCKLE BUCKLE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS THAT PROTECTS THE BUCKLE SURFACE. SELECT REPLY CODE 10AD09 BXQPA 12QUANTITY,MULTISTAGE,VALVE VALVE MULTISTAGE QUANTITY THE NUMBER OF STAGES IN A MULTISTAGE VALVE. 1A MODE REPLY 0 BXQQD /D/ 07HOOK,HANG-UP HANG-UP HOOK AN INDICATION OF WHETHER OR NOT A HANG-UP HOOK IS INCLUDED. SELECT REPLY CODE 10AA49 BXQRG 10CAPACITY RATING,FLOW,AIR AIR FLOW CAPACITY RATING THE RATED CAPACITY OF AIR FLOW. FULL TEXT WRITE-IN 0 BXQSD /D/ 18TYPE,COUPLING COUPLING TYPE INDICATES THE TYPE OF COUPLING PROVIDED. SELECT REPLY CODE 10AH98 BXQTJ 04DIAMETER,OUTSIDE,HOSE END HOSE END OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOSE END,AND TERMINATES ON THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BXQWA 12QUANTITY,GUN,SPRAY SPRAY GUN QUANTITY THE NUMBER OF SPRAY GUNS PROVIDED. 1A MODE REPLY 0 BXQXD /D/ 07FEATURE,DESIGN,SPRAY GUN EXTENSION HEAD SPRAY GUN EXTENSION HEAD DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A SPRAY GUN EXTENSION HEAD DESIGN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BXQYJ 04LENGTH,HEAD,EXTENSION EXTENSION HEAD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE EXTENSION HEAD,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BXQZD /D/ 19RELATIONSHIP TO EXTENSION,HEAD,SPRAY SPRAY HEAD RELATIONSHIP TO EXTENSION AN INDICATION OF THE RELATIONSHIP OF THE SPRAY HEAD TO THE EXTENSION. SELECT REPLY CODE 10AE98 BXRBB 10RELATIONSHIP TO EXTENSION IN DEG,ANGULAR,SPRAY HEAD SPRAY HEAD ANGULAR RELATIONSHIP TO EXTENSION IN DEG THE ANGULAR RELATIONSHIP OF THE SPRAY HEAD TO THE EXTENSION,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BXRCD /D/ 19RELATIONSHIP ON LONGITUDINAL AXIS,HEAD,EXTENSION EXTENSION HEAD RELATIONSHIP ON LONGITUDINAL AXIS AN INDICATION OF THE RELATIONSHIP OF THE EXTENSION HEAD ON THE LONGITUDINAL AXIS. SELECT REPLY CODE 10AE98 BXRDD 11METHOD,CONTROL,SPRAY GUN SPRAY GUN CONTROL METHOD THE MEANS BY WHICH THE SPRAY GUN IS CONTROLLED. SELECT REPLY CODE 10AL28 BXRFD 18TYPE,MIX,SPRAY GUN AIR CAP SPRAY GUN AIR CAP MIX TYPE INDICATES THE TYPE OF AIR CAP MIX PROVIDED ON THE SPRAY GUN. SELECT REPLY CODE 10AL82 BXRGG 10CONSUMPTION RATE,AIR,MAXIMUM MAXIMUM AIR CONSUMPTION RATE THE MAXIMUM AMOUNT OF AIR CONSUMPTION FOR WHICH THE ITEM IS RATED. FULL TEXT WRITE-IN 0 BXRHD 18TYPE,CUP,SPRAY GUN FEED SPRAY GUN FEED CUP TYPE INDICATES THE TYPE OF FEED CUP UTILIZED BY THE SPRAY GUN. SELECT REPLY CODE 10AK97 BXRJD /D/ 07TANK,FEED,PRESSURE MATERIAL PRESSURE MATERIAL FEED TANK AN INDICATION OF WHETHER OR NOT A PRESSURE MATERIAL FEED TANK IS INCLUDED. SELECT REPLY CODE 10AA49 BXRKD 18TYPE,TANK TANK TYPE INDICATES THE TYPE OF TANK PROVIDED. SELECT REPLY CODE 10AK54 BXRLD /D/ 07OUTLET,BOTTOM BOTTOM OUTLET AN INDICATION OF WHETHER OR NOT A BOTTOM OUTLET IS INCLUDED. SELECT REPLY CODE 10AA49 BXRMD /D/ 07CONTAINER,REMOVABLE REMOVABLE CONTAINER AN INDICATION OF WHETHER OR NOT A REMOVABLE CONTAINER IS INCLUDED. SELECT REPLY CODE 10AA49 BXRND /D/ 07REGULATOR REGULATOR AN INDICATION OF WHETHER OR NOT A REGULATOR IS INCLUDED. SELECT REPLY CODE 10AA49 BXRPG /D/ 19NAME AND QUANTITY,COMPONENT,TANK ACCESSORY TANK ACCESSORY COMPONENT NAME AND QUANTITY THE NAME AND NUMBER OF PARTS SUPPLIED WITH THE TANK WHICH MAY BE REQUIRED FOR APPLICATION. FULL TEXT WRITE-IN 0 BXRQD /D/ 07SEPARATOR,WATER WATER SEPARATOR AN INDICATION OF WHETHER OR NOT A WATER SEPARATOR IS INCLUDED. SELECT REPLY CODE 10AA49 BXRRJ 10PRESSURE RATE,WORKING,COMPRESSOR COMPRESSOR WORKING PRESSURE RATE THE AMOUNT OF WORKING PRESSURE FOR WHICH THE COMPRESSOR IS RATED. 2D AND 1B MODE REPLY22AG671AC20 BXRSD /D/ 07TANK,RECEIVER,AIR AIR RECEIVER TANK AN INDICATION OF WHETHER OR NOT AN AIR RECEIVER TANK IS INCLUDED. SELECT REPLY CODE 10AA49 BXRTJ 10CAPACITY,TANK,AIR RECEIVER AIR RECEIVER TANK CAPACITY THE RATED CAPACITY OF THE AIR RECEIVER TANK. 2D AND 1B MODE REPLY22AG671AC20 BXRWD 18TYPE,MOUNTING,COMPRESSOR COMPRESSOR MOUNTING TYPE INDICATES THE TYPE OF MOUNT UTILIZED TO SUPPORT THE COMPRESSOR. SELECT REPLY CODE 10AA78 BXRXD /D/ 07HEAD,EXTENSION EXTENSION HEAD AN INDICATION OF WHETHER OR NOT AN EXTENSION HEAD IS INCLUDED. SELECT REPLY CODE 10AA49 BXRYD /D/ 07HANDLE,ADAPTABLE ADAPTABLE HANDLE AN INDICATION OF WHETHER OR NOT AN ADAPTABLE HANDLE IS INCLUDED. SELECT REPLY CODE 10AA49 BXRZG /D/ 03DESIGNATION,MANUFACTURER,FLUID TIP SIZE FLUID TIP SIZE MANUFACTURER DESIGNATION THE MANUFACTURERS DESIGNATION INDICATING THE SIZE OF THE FLUID TIP. FULL TEXT WRITE-IN 0 BXSBJ 10DISPLACEMENT RATE,AIR,FREE FREE AIR DISPLACEMENT RATE THE VOLUME OF FREE AIR PASSED PER UNIT OF TIME THROUGH AN ITEM. 1D AND 1B MODE REPLY12AG67 BXSCG 13SCREW THREAD SERIES DESIGNATOR,CONNECTION,AIR HOSE AIR HOSE CONNECTION SCREW THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF AIR HOSE CONNECTION SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. FULL TEXT WRITE-IN 0 BXSDA /D/ 13THREAD SIZE,CONNECTION,FLUID HOSE FLUID HOSE CONNECTION THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED FLUID HOSE CONNECTION. 1A MODE REPLY 0 BXSFG 13SCREW THREAD SERIES DESIGNATOR,CONNECTION,FLUID HOSE FLUID HOSE CONNECTION SCREW THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF FLUID HOSE CONNECTION THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. FULL TEXT WRITE-IN 0 BXSGD /D/ 07ATTACHMENT,COVER COVER ATTACHMENT AN INDICATION OF WHETHER OR NOT A COVER ATTACHMENT IS PROVIDED. SELECT REPLY CODE 10AB22 BXSHD /D/ 19RELATIONSHIP TO FACE CENTERLINE,WEB/SPOKE WEB/SPOKE RELATIONSHIP TO FACE CENTERLINE AN INDICATION OF THE RELATIONSHIP BETWEEN THE WEBBING OR SPOKES AND THE CENTERLINE OF THE FACE. SELECT REPLY CODE 10AE98 BXSJD /D/ 07HOLE,LIGHTENING LIGHTENING HOLE AN INDICATION OF WHETHER OR NOT A LIGHTENING HOLE/S/ IS INCLUDED. PLEASE USEMRC ABFF FOR NIINS WERE ANSWERED WITH "INCLUDED" IN PLACE OF THIS CANCELLED MRC. SELECT REPLY CODE 10AA49 BXSKD /D/ 07VANE,COOLING,INTEGRAL INTEGRAL COOLING VANE AN INDICATION OF WHETHER OR NOT AN INTEGRAL COOLING VANE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BXSLD /D/ 07FACE,CROWN CROWN FACE AN INDICATION OF WHETHER OR NOT A CROWN FACE IS INCLUDED. SELECT REPLY CODE 10AA49 BXSMD 14SHAPE,GROOVE GROOVE SHAPE THE PHYSICAL CONFIGURATION OF THE GROOVE. SELECT REPLY CODE 10AD07 BXSNA 03DESIGNATION FOR WHICH DESIGNED,SECTION,STANDARD V-BELT STANDARD V-BELT SECTION DESIGNATION FOR WHICH DESIGNED THE ALPHA AND/OR NUMERIC SECTION DESIGNATION OF THE STANDARD V-BELT FOR WHICH DESIGNED. 1A MODE REPLY 0 BXSPJ 04DEPTH,MAXIMUM CUT,SCOOP SCOOP MAXIMUM CUT DEPTH THE MAXIMUM CUT DEPTH FOR WHICH THE SCOOP IS DESIGNED. 1D AND 1B MODE REPLY11AA05 BXSQJ 10CAPACITY,STRUCK,SCOOP SCOOP STRUCK CAPACITY THE STRUCK CAPACITY FOR WHICH THE SCOOP IS RATED. 1D AND 1B MODE REPLY11AD42 BXSRD /D/ 18TYPE,BOWL,SCOOP SCOOP BOWL TYPE INDICATES THE TYPE OF SCOOP BOWL PROVIDED. SELECT REPLY CODE 10AK54 BXSSJ 04DEPTH,SPREAD,MAXIMUM MAXIMUM SPREAD DEPTH THE DEPTH OF SPREAD FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AA05 BXSTJ 10CLEARANCE,GROUND,HAULING HAULING GROUND CLEARANCE A MEASUREMENT OF THE CLEARANCE BETWEEN THE BOTTOM OF THE ITEM AND THE GROUND WHEN HAULING. 1D AND 1B MODE REPLY11AA05 BXSWD /D/ 18TYPE FOR WHICH DESIGNED,DOZER DOZER TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF DOZER FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BXSXJ 10CLEARANCE,DUMPING,MAXIMUM MAXIMUM DUMPING CLEARANCE THE MAXIMUM CLEARANCE IN A FORWARD DUMPING POSITION. 1D AND 1B MODE REPLY11AA05 BXSYJ /D/ 10CAPACITY RATING,BUCKET,SAE SAE BUCKET CAPACITY RATING THE BUCKET CAPACITY AS RATED BY THE SOCIETY OF AUTOMOTIVE ENGINEERS. 2D AND 1B MODE REPLY21AD421AC20 BXSZJ 04WIDTH,BUCKET BUCKET WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BUCKET,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BXTBD 18TYPE,BUCKET BUCKET TYPE INDICATES THE TYPE OF BUCKET PROVIDED. SELECT REPLY CODE 10AK54 BXTCD /D/ 07TRANSMISSION,TORQUE CONVERTER,HYDRAULIC HYDRAULIC TORQUE CONVERTER TRANSMISSION AN INDICATION OF WHETHER OR NOT A HYDRAULIC TORQUE CONVERTER TRANSMISSION IS INCLUDED. SELECT REPLY CODE 10AA49 BXTDD /D/ 07SYSTEM,STEERING,HINGED FRAME HINGED FRAME STEERING SYSTEM AN INDICATION OF WHETHER OR NOT A HINGED FRAME STEERING SYSTEM IS INCLUDED. SELECT REPLY CODE 10AA49 BXTFD /D/ 07AXLE,TYPE,PLANETARY PLANETARY TYPE AXLE AN INDICATION OF WHETHER OR NOT A PLANETARY TYPE AXLE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BXTGD /D/ 07CAB,CLOSED CLOSED CAB AN INDICATION OF WHETHER OR NOT A CLOSED CAB IS INCLUDED. SELECT REPLY CODE 10AA49 BXTHJ 10CAPACITY,BUCKET BUCKET CAPACITY THE RATED CAPACITY THAT THE BUCKET WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AD42 BXTJD 11METHOD,DISCHARGE,BUCKET BUCKET DISCHARGE METHOD THE MEANS PROVIDED FOR THE BUCKET DISCHARGE. SELECT REPLY CODE 10AJ91 BXTKJ /D/ 10CAPACITY,LIFTING,MAXIMUM MAXIMUM LIFTING CAPACITY THE MAXIMUM WEIGHT THAT THE ITEM IS DESIGNED TO LIFT. 1D AND 1B MODE REPLY11AB10 BXTLD /D/ 07CAB CAB AN INDICATION OF WHETHER OR NOT A CAB IS INCLUDED. SELECT REPLY CODE 10AA49 BXTMJ 04HEIGHT,MAXIMUM,DISCHARGE DISCHARGE MAXIMUM HEIGHT THE MAXIMUM HEIGHT AT WHICH THE ITEM IS DESIGNED TO DISCHARGE. 1D AND 1B MODE REPLY11AA05 BXTNJ 10CAPACITY,SCOOP SCOOP CAPACITY THE RATED LOAD THAT THE SCOOP WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AD42 BXTQG /D/ 19NUMBER,MODEL,TRUCK TRUCK MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE TRUCK. FULL TEXT WRITE-IN 0 BXTRJ 04DISTANCE BETWEEN SPROCKETS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SPROCKETS THE CENTER TO CENTER DISTANCE BETWEEN THE SPROCKETS. 2D AND 1B MODE REPLY21AA051AC20 BXTSD 11METHOD,OPERATION,DEPTH CONTROL DEPTH CONTROL OPERATION METHOD THE MEANS USED FOR OPERATING THE DEPTH CONTROL. SELECT REPLY CODE 10AK54 BXTTD 18TYPE,FACILITY,DISCHARGE DISCHARGE FACILITY TYPE INDICATES THE TYPE OF FACILITY UTILIZED FOR DISCHARGING. SELECT REPLY CODE 10AK54 BXTWJ 04LENGTH,FACILITY,DISCHARGE DISCHARGE FACILITY LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE DISCHARGE FACILITY,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BXTXJ 04WIDTH,FACILITY,DISCHARGE DISCHARGE FACILITY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE DISCHARGE FACILITY,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BXTYJ 04HEIGHT,DUMPING,DISCHARGE FACILITY DISCHARGE FACILITY DUMPING HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE DISCHARGE FACILITY IN THE DUMPING POSITION,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BXTZJ 04DEPTH,CUT,MAXIMUM MAXIMUM CUT DEPTH AN INDICATION OF THE MAXIMUM CUT DEPTH. 1D AND 1B MODE REPLY11AA05 BXWBJ 04WIDTH,MINIMUM,CUT CUT MINIMUM WIDTH THE MINIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CUT. 1D AND 1B MODE REPLY11AA05 BXWCJ 10SPEED,DIGGING,MAXIMUM MAXIMUM DIGGING SPEED THE MAXIMUM DIGGING SPEED AT WHICH THE ITEM IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY12AB49 BXWDD /D/ 18TYPE FOR WHICH DESIGNED,TRACTOR TRACTOR TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF TRACTOR FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BXWFJ 04DIAMETER,FLANGE,DRUM DRUM FLANGE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DRUM FLANGE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BXWGG 10CAPACITY,CABLE,DRUM DRUM CABLE CAPACITY THE CAPACITY OF THE DRUM CABLE. FULL TEXT WRITE-IN 0 BXWHG /D/ 10PULL,LINE,MAXIMUM MAXIMUM LINE PULL AN INDICATION OF THE MAXIMUM LINE PULL. FULL TEXT WRITE-IN 0 BXWJJ T10RANGE,SPEED,LINE LINE SPEED RANGE THE LINE SPEED RANGE FOR WHICH THE ITEM IS RATED. 1D AND 1F MODE REPLY12AB49 BXWKD 18TYPE,DUMP DUMP TYPE INDICATES THE TYPE OF DUMP. SELECT REPLY CODE 10AK54 BXWLD /D/ 18TYPE,DUMP,BODY BODY DUMP TYPE INDICATES THE BODY DUMP TYPE. SELECT REPLY CODE 10AK54 BXWND 11METHOD,OPERATION,DUMP MECHANISM DUMP MECHANISM OPERATION METHOD THE MEANS USED TO OPERATE THE DUMP MECHANISM. SELECT REPLY CODE 10AK54 BXWPD /D/ 09MATERIAL,FRAMING,SIDEWALL SIDEWALL FRAMING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SIDEWALL FRAME IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXWQD /D/ 09MATERIAL,SIDEWALL,OUTSIDE OUTSIDE SIDEWALL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE OUTSIDE SIDEWALL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXWRD /D/ 09MATERIAL,SIDEWALL,INSIDE INSIDE SIDEWALL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INSIDE SIDEWALL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXWSD /D/ 09MATERIAL,FRAMING,ENDWALL ENDWALL FRAMING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ENDWALL FRAME IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXWTD /D/ 09MATERIAL,ENDWALL,OUTSIDE OUTSIDE ENDWALL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE OUTSIDE ENDWALL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXWWD /D/ 09MATERIAL,ENDWALL,INSIDE INSIDE ENDWALL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INSIDE ENDWALL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXWXD /D/ 09MATERIAL,FRAMING,FLOOR FLOOR FRAMING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FLOOR FRAME IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXWYD /D/ 09MATERIAL,POST,FOUNDATION FOUNDATION POST MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FOUNDATION POST(S) IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXWZD /D/ 09MATERIAL,SKIRTING SKIRTING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SKIRTING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXXBD /D/ 09MATERIAL,SKID SKID MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SKID(S) IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXXCD /D/ 09MATERIAL,CEILING CEILING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CEILING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXXDD /D/ 09MATERIAL,PARTITION PARTITION MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PARTITION(S) IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXXFA 12QUANTITY,ROOM ROOM QUANTITY THE NUMBER OF ROOMS PROVIDED. 1A MODE REPLY 0 BXXGA 12QUANTITY,OPENING,DOOR DOOR OPENING QUANTITY THE NUMBER OF DOOR OPENINGS PROVIDED. 1A MODE REPLY 0 BXXHD 18TYPE,OPENING,DOOR DOOR OPENING TYPE INDICATES THE TYPE OF DOOR OPENING PROVIDED. SELECT REPLY CODE 10AJ91 BXXJJ 04WIDTH,OPENING,DOOR DOOR OPENING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE DOOR UPRIGHTS. 2D AND 1B MODE REPLY21AA051AC20 BXXKJ 04HEIGHT,OPENING,DOOR DOOR OPENING HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE DOOR OPENING,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BXXLJ 04WIDTH,DOOR DOOR WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE DOOR. 2D AND 1B MODE REPLY21AA051AC20 BXXMJ 04HEIGHT,DOOR DOOR HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE DOOR,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BXXNA 12QUANTITY,OPENING,WINDOW WINDOW OPENING QUANTITY THE NUMBER OF WINDOW OPENINGS PROVIDED. 1A MODE REPLY 0 BXXPD 18TYPE,OPENING,WINDOW WINDOW OPENING TYPE INDICATES THE TYPE OF WINDOW OPENING PROVIDED. SELECT REPLY CODE 10AJ91 BXXQD 08LOCATION,OPENING,WINDOW WINDOW OPENING LOCATION INDICATES THE LOCATION OF THE WINDOW OPENING. SELECT REPLY CODE 10AJ91 BXXRJ 04WIDTH,OPENING,WINDOW WINDOW OPENING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE WINDOW OPENING. 2D AND 1B MODE REPLY21AA051AC20 BXXSJ 04HEIGHT,OPENING,WINDOW WINDOW OPENING HEIGHT A MEASUREMENT TAKEN FROM THE BOTTOM TO THE TOP OF THE WINDOW OPENING,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BXXTA 12QUANTITY,SHUTTER SHUTTER QUANTITY THE NUMBER OF SHUTTERS PROVIDED. 1A MODE REPLY 0 BXXWA 12QUANTITY,SCREEN SCREEN QUANTITY THE NUMBER OF SCREENS PROVIDED. 1A MODE REPLY 0 BXXXA 12QUANTITY,OPENING,LOUVER LOUVER OPENING QUANTITY THE NUMBER OF LOUVER OPENINGS PROVIDED. 1A MODE REPLY 0 BXXYA 12QUANTITY,LOUVER LOUVER QUANTITY THE NUMBER OF LOUVERS PROVIDED. 1A MODE REPLY 0 BXXZA 12QUANTITY,OPENING,VENTILATOR VENTILATOR OPENING QUANTITY THE NUMBER OF VENTILATOR OPENINGS PROVIDED. 1A MODE REPLY 0 BXYBA 12QUANTITY,VENTILATOR VENTILATOR QUANTITY THE NUMBER OF VENTILATORS PROVIDED. 1A MODE REPLY 0 BXYCA 12QUANTITY,OPENING,STACK STACK OPENING QUANTITY THE NUMBER OF STACK OPENINGS PROVIDED. 1A MODE REPLY 0 BXYDL /D/ 16STYLE FOR WHICH DESIGNED,BUILDING BUILDING STYLE FOR WHICH DESIGNED THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BUILDING FOR WHICH THE ITEM IS DESIGNED. 1L MODE REPLY 0 BXYFJ /D/ 04HEIGHT,EAVES EAVES HEIGHT A MEASUREMENT TAKEN FROM THE BOTTOM TO THE TOP OF THE EAVES,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BXYGD /D/ 09MATERIAL,FRAMING,PANEL PANEL FRAMING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PANEL FRAME IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXYHD /D/ 09MATERIAL,FACING,PANEL INTERIOR PANEL INTERIOR FACING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PANEL INTERIOR FACING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXYJD /D/ 09MATERIAL,FACING,PANEL EXTERIOR PANEL EXTERIOR FACING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PANEL EXTERIOR FACING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXYKD /D/ 07INSULATION,PANEL PANEL INSULATION AN INDICATION OF WHETHER OR NOT INSULATION IS INCLUDED WITH THE PANEL. SELECT REPLY CODE 10AA49 BXYLD /D/ 07SECTION,SCREENED,PANEL PANEL SCREENED SECTION AN INDICATION OF WHETHER OR NOT A PANEL SCREENED SECTION IS INCLUDED. SELECT REPLY CODE 10AA49 BXYMD /D/ 07CURTAIN CURTAIN AN INDICATION OF WHETHER OR NOT A CURTAIN(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BXYND /D/ 09MATERIAL,CURTAIN CURTAIN MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CURTAIN IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BXYPJ /D/ 04DISTANCE FROM BEND TO CENTERLINE DISTANCE FROM BEND TO CENTERLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 BXYQJ /D/ 04THICKNESS,ARM,LEFT FORK LEFT FORK ARM THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BXYRD /D/ 19FACILITY,MOUNTING,LEVER LEVER MOUNTING FACILITY AN INDICATION OF THE FACILITY USED FOR MOUNTING THE ITEM. SELECT REPLY CODE 10AM39 BXYSL 16STYLE,CONNECTION,PISTON END PISTON END CONNECTION STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PISTON END CONNECTION. 1L MODE REPLY 0 BXYTJ /D/ 04DIAMETER,INSIDE,PISTON END PISTON END INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXYWJ /D/ 04DIAMETER,INSIDE,CYLINDER END CYLINDER END INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXYXJ /D/ 04DIAMETER,INSIDE,LARGEST,PISTON END PISTON END LARGEST INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXYZJ /D/ 04DIAMETER,INSIDE,LARGEST,CYLINDER END CYLINDER END LARGEST INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZBJ /D/ 04DIAMETER,OUTSIDE,PISTON END PISTON END OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZCJ /D/ 04DIAMETER,OUTSIDE,CYLINDER END CYLINDER END OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZDJ /D/ 04THICKNESS,END,PISTON PISTON END THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZFJ /D/ 04THICKNESS,END,CYLINDER CYLINDER END THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZGJ /D/ 04WIDTH,END,PISTON PISTON END WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZHJ /D/ 04WIDTH,END,CYLINDER CYLINDER END WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZJJ /D/ 04DEPTH,FORK,END,PISTON PISTON END FORK DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZKJ /D/ 04DEPTH,FORK,END,CYLINDER CYLINDER END FORK DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZLJ /D/ 04THICKNESS,ARM,PISTON END FORK PISTON END FORK ARM THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZMJ /D/ 04THICKNESS,ARM,CYLINDER END FORK CYLINDER END FORK ARM THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZNJ /D/ 04THICKNESS,ARM,PISTON END RIGHT FORK PISTON END RIGHT FORK ARM THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZPJ /D/ 04THICKNESS,ARM,CYLINDER END RIGHT FORK CYLINDER END RIGHT FORK ARM THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZQJ /D/ 04WIDTH,SPAN,FORK,PISTON END PISTON END FORK SPAN WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZRJ /D/ 04WIDTH,SPAN,FORK,CYLINDER END CYLINDER END FORK SPAN WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZSJ /D/ 04LENGTH,SHANK,PISTON END PISTON END SHANK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZTJ /D/ 04LENGTH,SHANK,CYLINDER END CYLINDER END SHANK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZWJ /D/ 04DIAMETER,SHANK,PISTON END PISTON END SHANK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZXJ /D/ 04DIAMETER,SHANK,CYLINDER END CYLINDER END SHANK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZYJ /D/ 04LENGTH,PORTION,UNTHREADED,PISTON END SHANK PISTON END SHANK UNTHREADED PORTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BXZZJ /D/ 04LENGTH,PORTION,UNTHREADED,CYLINDER END SHANK CYLINDER END SHANK UNTHREADED PORTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYBBA /D/ 13THREAD SIZE,CONNECTION,PISTON END PISTON END CONNECTION THREAD SIZE DESIGNATES THE THREAD DIAMETER AND THE NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED PISTON END CONNECTION. 1A MODE REPLY 0 BYBCD /D/ 13THREAD SERIES DESIGNATOR,CONNECTION,PISTON END PISTON END CONNECTION THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF PISTON END CONNECTION THREAD DIAMETER-PITCH COMBINATION FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 BYBDD /D/ 13THREAD DIRECTION,CONNECTION,PISTON END PISTON END CONNECTION THREAD DIRECTION THE DIRECTION OF THE PISTON END CONNECTION THREAD WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AA38 BYBFL 16STYLE,CONNECTION,CYLINDER END CYLINDER END CONNECTION STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CYLINDER END CONNECTION. 1L MODE REPLY 0 BYBGA /D/ 13THREAD SIZE,CONNECTION,CYLINDER END CYLINDER END CONNECTION THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED CYLINDER END CONNECTION. 1A MODE REPLY 0 BYBHD /D/ 13THREAD SERIES DESIGNATOR,CONNECTION,CYLINDER END CYLINDER END CONNECTION THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF CYLINDER END CONNECTION THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 BYBJD /D/ 13THREAD DIRECTION,CONNECTION,CYLINDER END CYLINDER END CONNECTION THREAD DIRECTION THE DIRECTION OF THE CYLINDER END CONNECTION THREAD WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AA38 BYBKB 10TRAVEL IN DEG,ARM ARM TRAVEL IN DEG THE DISTANCE THE ARM WILL TRAVEL,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BYBMJ 04LENGTH,TRAVEL TRAVEL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION THE ARM WILL TRAVEL. 2D AND 1B MODE REPLY21AA051AC20 BYBND /D/ 07SHIELD,DUST DUST SHIELD AN INDICATION OF WHETHER OR NOT A DUST SHIELD IS INCLUDED. SELECT REPLY CODE 10AA49 BYBPG 08LOCATION,BUCKLE BUCKLE LOCATION INDICATES THE LOCATION OF THE BUCKLE(S). FULL TEXT WRITE-IN 0 BYBQD /D/ 07FEATURE,BUCKLE,FASTENED FASTENED BUCKLE FEATURE AN INDICATION OF WHETHER OR NOT A FASTENED BUCKLE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BYBRD 11METHOD,FASTENING,BUCKLE BUCKLE FASTENING METHOD THE MEANS USED TO FASTEN THE BUCKLE(S). SELECT REPLY CODE 10AF69 BYBSG /D/ 08LOCATION AND QUANTITY,HOLE,BUCKLE TONGUE BUCKLE TONGUE HOLE LOCATION AND QUANTITY INDICATES THE LOCATION AND NUMBER OF BUCKLE TONGUE HOLES ON THE ITEM. FULL TEXT WRITE-IN 0 BYBTD 18TYPE,FOLD FOLD TYPE INDICATES THE TYPE OF FOLD(S) UTILIZED ON THE ITEM. SELECT REPLY CODE 10AF05 BYBWJ 04DISTANCE FROM STRAP END TO FIRST HOLE DISTANCE FROM STRAP END TO FIRST HOLE THE DISTANCE FROM THE STRAP END TO THE FIRST HOLE. 2D AND 1B MODE REPLY21AA051AC20 BYBXA /D/ 16STYLE DESIGNATOR,CLIP,END END CLIP STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END CLIP/S/. 1A MODE REPLY 0 BYBYD /D/ 09MATERIAL,CLIP,END END CLIP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE END CLIP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BYBZA 12QUANTITY,CLIP,END END CLIP QUANTITY THE NUMBER OF END CLIPS PROVIDED. 1A MODE REPLY 0 BYCBL 16STYLE DESIGNATOR,HOOK HOOK STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HOOK(S). 1L MODE REPLY 0 BYCCD 18TYPE,CONNECTION,HOOK HOOK CONNECTION TYPE INDICATES THE TYPE OF HOOK CONNECTION(S) PROVIDED. SELECT REPLY CODE 10AL49 BYCDD /D/ 07FEATURE,HOOK,FASTENED FASTENED HOOK FEATURE AN INDICATION OF WHETHER OR NOT A FASTENED HOOK FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BYCFD 11METHOD,FASTENING,HOOK HOOK FASTENING METHOD THE MEANS USED TO FASTEN THE HOOK(S). SELECT REPLY CODE 10AF69 BYCGD /D/ 09MATERIAL,KEEPER KEEPER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE KEEPER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BYCHA 12QUANTITY,KEEPER KEEPER QUANTITY THE NUMBER OF KEEPERS PROVIDED. 1A MODE REPLY 0 BYCJD /D/ 07FEATURE,KEEPER,FASTENED FASTENED KEEPER FEATURE AN INDICATION OF WHETHER OR NOT A FASTENED KEEPER FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BYCKA /D/ 16STYLE DESIGNATOR,LOOP LOOP STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LOOP(S). 1A MODE REPLY 0 BYCLD /D/ 09MATERIAL,LOOP LOOP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LOOP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BYCMD /D/ 07FEATURE,LOOP,FASTENED FASTENED LOOP FEATURE AN INDICATION OF WHETHER OR NOT A FASTENED LOOP FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BYCND 11METHOD,FASTENING,LOOP LOOP FASTENING METHOD THE MEANS USED TO FASTEN THE LOOP(S). SELECT REPLY CODE 10AF69 BYCPG 08LOCATION,LOOP LOOP LOCATION INDICATES THE LOCATION OF THE LOOP(S). FULL TEXT WRITE-IN 0 BYCQA 12QUANTITY,GROMMET GROMMET QUANTITY THE NUMBER OF GROMMETS PROVIDED. 1A MODE REPLY 0 BYCRA /D/ 16STYLE DESIGNATOR,WASHER,GROMMET GROMMET WASHER STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE GROMMET WASHER. 1A MODE REPLY 0 BYCSJ 04DISTANCE FROM STRAP END TO FIRST GROMMET HOLE CENTER DISTANCE FROM STRAP END TO FIRST GROMMET HOLE CENTER THE DISTANCE FROM THE STRAP END TO THE HOLE CENTER OF THE FIRST GROMMET. 2D AND 1B MODE REPLY21AA051AC20 BYCTJ 04DISTANCE BETWEEN GROMMET HOLE CENTERS DISTANCE BETWEEN GROMMET HOLE CENTERS THE DISTANCE BETWEEN GROMMET HOLE CENTERS. 2D AND 1B MODE REPLY21AA051AC20 BYCWA /D/ 16STYLE DESIGNATOR,BARREL,GROMMET GROMMET BARREL STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE GROMMET BARREL. 1A MODE REPLY 0 BYCXA /D/ 16STYLE DESIGNATOR,FLANGE,GROMMET GROMMET FLANGE STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE GROMMET FLANGE. 1A MODE REPLY 0 BYCYD 11METHOD,FASTENING,PAD PAD FASTENING METHOD THE MEANS USED TO FASTEN THE PAD(S). SELECT REPLY CODE 10AF69 BYCZD 14SHAPE,RING RING SHAPE THE PHYSICAL CONFIGURATION OF THE RING. SELECT REPLY CODE 10AD07 BYDBD /D/ 07FEATURE,RING,FASTENED FASTENED RING FEATURE AN INDICATION OF WHETHER OR NOT A FASTENED RING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BYDCD 11METHOD,FASTENING,RING RING FASTENING METHOD THE MEANS USED TO FASTEN THE RING(S). SELECT REPLY CODE 10AF69 BYDDG 08LOCATION,RING RING LOCATION INDICATES THE LOCATION OF THE RING(S). FULL TEXT WRITE-IN 0 BYDFJ 04DISTANCE FROM STRAP END TO SNAP FASTENER,SHORTEST SHORTEST DISTANCE FROM STRAP END TO SNAP FASTENER THE SHORTEST DISTANCE FROM THE END OF THE STRAP TO THE SNAP FASTENER. 1D AND 1B MODE REPLY11AA05 BYDGD /D/ 07PAD,ANTIABRASION ANTIABRASION PAD AN INDICATION OF WHETHER OR NOT AN ANTIABRASION PAD(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BYDHJ 04WIDTH,OVERALL,BUCKLE BUCKLE OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYDJJ 04LENGTH,BUCKLE BUCKLE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYDKJ 04DISTANCE FROM MOUNTING HOLE CENTER TO BUCKLE END DISTANCE FROM MOUNTING HOLE CENTER TO BUCKLE END NONE. 2D AND 1B MODE REPLY21AA051AC20 BYDLJ 04DISTANCE FROM MOUNTING HOLE CENTER TO SWIVEL BASE DISTANCE FROM MOUNTING HOLE CENTER TO SWIVEL BASE NONE. 2D AND 1B MODE REPLY21AA051AC20 BYDMJ 04DISTANCE FROM RIVET CENTER TO RIVET BASE DISTANCE FROM RIVET CENTER TO RIVET BASE NONE. 2D AND 1B MODE REPLY21AA051AC20 BYDNJ /D/ 04DISTANCE FROM MOUNTING HOLE CENTER TO LUG EDGE DISTANCE FROM MOUNTING HOLE CENTER TO LUG EDGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BYDPD 18TYPE,RIM RIM TYPE INDICATES THE TYPE OF RIM PROVIDED. SELECT REPLY CODE 10AK54 BYDQJ A12QUANTITY,LINE LINE QUANTITY THE NUMBER OF LINES PER MEASUREMENT SCALE. 1D AND 1A MODE REPLY13AJ40 BYDRD 08LOCATION,FLANGE FLANGE LOCATION INDICATES THE LOCATION OF THE FLANGE ON THE ITEM. SELECT REPLY CODE 10AJ91 BYDSD /D/ 07FEATURE,BORE BORE FEATURE AN INDICATION OF WHETHER OR NOT A BORE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BYDTD 18TYPE,BEARING BEARING TYPE INDICATES THE TYPE OF BEARING PROVIDED. SELECT REPLY CODE 10AH96 BYDWJ 10SIZE FOR WHICH DESIGNED,SHAFT SHAFT SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE SHAFT FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 BYDXD 08LOCATION,DIAMETER,LARGEST MINOR,TAPERED SPLINE TAPERED SPLINE LARGEST MINOR DIAMETER LOCATION INDICATES THE LOCATION OF THE TAPERED SPLINE LARGEST MINOR DIAMETER. SELECT REPLY CODE 10AJ91 BYDYD /D/ 08LOCATION,DIMENSION,LARGEST,KEYING FACILITY KEYING FACILITY LARGEST DIMENSION LOCATION INDICATES THE LOCATION OF THE LARGEST DIMENSION OF THE KEYING FACILITY. SELECT REPLY CODE 10AJ91 BYDZD 19CHARACTERISTIC,HUB,PROTRUDING PROTRUDING HUB CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC OF THE PROTRUDING HUB. SELECT REPLY CODE 10AJ88 BYFBD /D/ 08LOCATION,GROOVE/STEP GROOVE/STEP LOCATION INDICATES THE LOCATION OF THE GROOVE OR STEP ON THE ITEM. SELECT REPLY CODE 10AJ91 BYFCD 08LOCATION,SPLIT,HUB HUB SPLIT LOCATION INDICATES THE LOCATION OF THE SPLIT(S) ON THE HUB. SELECT REPLY CODE 10AJ91 BYFDA 12QUANTITY,BOLT,CLAMPING CLAMPING BOLT QUANTITY THE NUMBER OF CLAMPING BOLTS PROVIDED. 1A MODE REPLY 0 BYFFD 08LOCATION,SECURING SECURING LOCATION INDICATES THE LOCATION FOR SECURING THE ITEM. SELECT REPLY CODE 10AJ91 BYFGA 04SIZE,HOLE,TAPERED TAPERED HOLE SIZE DESIGNATES THE STANDARD SIZE DESIGNATION OF THE TAPERED HOLE. 1A MODE REPLY 0 BYFHD /D/ 04SIZE FOR WHICH DESIGNED,BELT/CHAIN/FILM BELT/CHAIN/FILM SIZE FOR WHICH DESIGNED DESIGNATES THE BELT,CHAIN,OR FILM SIZE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BYFJD /D/ 18TYPE FOR WHICH DESIGNED,PITCH,ROLLER CHAIN ROLLER CHAIN PITCH TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF ROLLER CHAIN PITCH FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BYFLA 12QUANTITY,ROW,TEETH TEETH ROW QUANTITY THE NUMBER OF ROWS OF TEETH PROVIDED. 1A MODE REPLY 0 BYFMJ 04DISTANCE BETWEEN TEETH ROWS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN TEETH ROWS THE CENTER TO CENTER DISTANCE BETWEEN THE TEETH ROWS. 2D AND 1B MODE REPLY21AA051AC20 BYFNA 12QUANTITY PER ROW,TEETH TEETH QUANTITY PER ROW THE NUMBER OF TEETH INCLUDED IN EACH ROW. 1A MODE REPLY 0 BYFPA 19NUMBER,CHAIN,ASA STANDARD ASA STANDARD CHAIN NUMBER THE AMERICAN STANDARDS ASSOCIATION NUMBER BY WHICH THE CHAIN IS IDENTIFIED. 1A MODE REPLY 0 BYFQD 11METHOD,TEST,HARDNESS RATING HARDNESS RATING TEST METHOD THE MEANS USED TO TEST THE RATED HARDNESS OF AN ITEM. SELECT REPLY CODE 10AL43 BYFRJ 10HARDNESS RATING,TEETH TEETH HARDNESS RATING A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF THE TEETH WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE. 2D AND 1B MODE REPLY22AC261AC20 BYFSD /D/ 07BEARING,BORE BORE BEARING AN INDICATION OF WHETHER OR NOT A BORE BEARING IS INCLUDED. PLEASE USE MRC ABFF FOR NIINS WERE ANSWERD WITH "INCLUDED" IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BYFTJ 04DISTANCE,RADIAL CENTER TO FLAT SURFACE RADIAL CENTER TO FLAT SURFACE DISTANCE THE DISTANCE FROM THE RADIAL CENTER TO THE FLAT SURFACE. 2D AND 1B MODE REPLY21AA051AC20 BYFWD /D/ 07KEYWAY,EXTERNAL,HUB HUB EXTERNAL KEYWAY AN INDICATION OF WHETHER OR NOT A HUB EXTERNAL KEYWAY IS INCLUDED. SELECT REPLY CODE 10AA49 BYFXD 08LOCATION,KEYWAY,EXTERNAL EXTERNAL KEYWAY LOCATION INDICATES THE LOCATION OF THE EXTERNAL KEYWAY. SELECT REPLY CODE 10AJ91 BYFYJ /D/ 04DIAMETER,KEYWAY KEYWAY DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR KEYWAY,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BYFZD 19CONSTRUCTION,BLOCK BLOCK CONSTRUCTION THE CONSTRUCTION OF THE BLOCK. SELECT REPLY CODE 10AL59 BYGBD 18TYPE,ROLLER ROLLER TYPE INDICATES THE TYPE OF ROLLER(S) PROVIDED. SELECT REPLY CODE 10AK54 BYGCD /D/ 18TYPE,PLATE,LINK LINK PLATE TYPE INDICATES THE TYPE OF LINK PLATE PROVIDED. SELECT REPLY CODE 10AK41 BYGDJ 10PITCH,CHAIN CHAIN PITCH THE CENTER TO CENTER DISTANCE BETWEEN THE CHAIN LINK PINS MEASURED ALONG THE PITCH LINE. 2D AND 1B MODE REPLY21AA051AC20 BYGFJ 10PITCH,TOOTH TOOTH PITCH THE CENTER TO CENTER DISTANCE BETWEEN TEETH MEASURED ALONG THE PITCH LINE. 2D AND 1B MODE REPLY21AA051AC20 BYGGJ 04HEIGHT,BLOCK BLOCK HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A BLOCK,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BYGHA /D/ 12QUANTITY,PITCH,LENGTH LENGTH PITCH QUANTITY THE NUMBER OF PITCHES EXTENDING THE LENGTH OF THE ITEM. 1A MODE REPLY 0 BYGJA /D/ 12QUANTITY,LINK,CROSS-SECTIONAL CROSS-SECTIONAL LINK QUANTITY THE NUMBER OF LINKS INCLUDED ACROSS THE WIDTH OF AN ITEM. 1A MODE REPLY 0 BYGKJ /D/ 04THICKNESS,LINK,CROSS-SECTIONAL CROSS-SECTIONAL LINK THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A CROSS-SECTIONAL LINK,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BYGLD 18TYPE,DEVICE,ATTACHMENT ATTACHMENT DEVICE TYPE INDICATES THE TYPE OF DEVICE USED FOR FASTENING AND/OR POSITIONING THE ITEM. SELECT REPLY CODE 10AJ74 BYGMD /D/ 18TYPE,PLATE,LINK,CONNECTING CONNECTING LINK PLATE TYPE INDICATES THE TYPE OF LINK PLATE USED TO CONNECT THE ITEM. SELECT REPLY CODE 10AK41 BYGND /D/ 07SHIELD,STONE STONE SHIELD AN INDICATION OF WHETHER OR NOT A STONE SHIELD IS INCLUDED. SELECT REPLY CODE 10AA49 BYGPD /D/ 07COMPARTMENT,STORAGE STORAGE COMPARTMENT AN INDICATION OF WHETHER OR NOT A STORAGE COMPARTMENT IS INCLUDED. SELECT REPLY CODE 10AA49 BYGQD /D/ 07FEATURE,REPAIRABLE REPAIRABLE FEATURE AN INDICATION OF WHETHER OR NOT A REPAIRABLE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BYGRJ /D/ 10RESISTANCE,COMPRESSION COMPRESSION RESISTANCE AN INDICATION OF THE AMOUNT OF COMPRESSION OPPOSITION OFFERED BY THE ITEM. 1D AND 1B MODE REPLY12AG67 BYGSJ /D/ 10RESISTANCE,REBOUND REBOUND RESISTANCE AN INDICATION OF THE AMOUNT OF REBOUND RESISTANCE OFFERED BY THE ITEM. 1D AND 1B MODE REPLY12AG67 BYGTA /D/ 12QUANTITY PER MINUTE,STROKE,RATED RATED STROKE QUANTITY PER MINUTE THE NUMBER OF STROKES PER MINUTE AT WHICH THE ITEM IS RATED. 1A MODE REPLY 0 BYGWJ 04DIAMETER,OUTSIDE,NECK NECK OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BYGXJ 04LENGTH,TAPERED,BASE BASE TAPERED LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYGYJ 04WIDTH,TAPERED,BASE BASE TAPERED WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYGZJ 04LENGTH,TAPERED,BODY BODY TAPERED LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYHBJ /D/ 04HEIGHT,TAPERED,BODY BODY TAPERED HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BYHCJ 04DIAMETER,OVERALL,FLANGE FLANGE OVERALL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BYHDJ 04THICKNESS,METAL,SHEET SHEET METAL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE SHEET METAL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BYHGG /D/ 03DESIGNATION,SIZE,TIRE TIRE SIZE DESIGNATION THE SIZE DESIGNATION BY WHICH THE TIRE IS IDENTIFIED. FULL TEXT WRITE-IN 0 BYHHB /D/ 04SIZE FOR WHICH DESIGNED,CROSS-SECTIONAL,TIRE TIRE CROSS-SECTIONAL SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE TIRE CROSS SECTION FOR WHICH THE ITEM IS DESIGNED. 1B MODE REPLY 0 BYHJD /D/ 09MATERIAL,CHAIN,CROSS CROSS CHAIN MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CROSS CHAIN IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BYHKD /D/ 17SURFACE TREATMENT,CHAIN,CROSS CROSS CHAIN SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A CROSS CHAIN SURFACE. SELECT REPLY CODE 10AD09 BYHLD /D/ 09MATERIAL,CHAIN,SIDE SIDE CHAIN MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SIDE CHAIN IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BYHMD /D/ 17SURFACE TREATMENT,CHAIN,SIDE SIDE CHAIN SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SIDE CHAIN SURFACE. SELECT REPLY CODE 10AD09 BYHNA 12QUANTITY,LINK,CROSS CHAIN CROSS CHAIN LINK QUANTITY THE NUMBER OF CROSS CHAIN LINKS PROVIDED. 1A MODE REPLY 0 BYHPD 18TYPE,CHAIN,CROSS CROSS CHAIN TYPE INDICATES THE TYPE OF CROSS CHAIN PROVIDED. SELECT REPLY CODE 10AC71 BYHQJ 04LENGTH,CHAIN,CROSS CROSS CHAIN LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CROSS CHAIN,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BYHRA 12QUANTITY,CHAIN,CROSS CROSS CHAIN QUANTITY THE NUMBER OF CROSS CHAINS PROVIDED. 1A MODE REPLY 0 BYHSD /D/ 07INDICATOR,CASEHARDENING,CROSS CHAIN CROSS CHAIN CASEHARDENING INDICATOR INDICATES WHETHER OR NOT A FERROUS ALLOY CROSS CHAIN HAS BEEN SUBJECTED TO A PROCESS WHEREBY THE OUTER PORTION IS MADE SUBSTANTIALLY HARDER THAN THE INNER PORTION OR CORE. SELECT REPLY CODE 10AA70 BYHTJ 10SIZE,WIRE,CROSS CHAIN LINK CROSS CHAIN LINK WIRE SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE CROSS CHAIN LINK WIRE. 2D AND 1B MODE REPLY21AA051AC20 BYHWJ 10SIZE,WIRE,CROSS CHAIN HOOK CROSS CHAIN HOOK WIRE SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE CROSS CHAIN HOOK WIRE. 2D AND 1B MODE REPLY21AA051AC20 BYHXJ 04LENGTH,CHAIN,OUTER SIDE OUTER SIDE CHAIN LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE OUTER SIDE CHAIN,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BYHYA 12QUANTITY,LINK,OUTER SIDE CHAIN OUTER SIDE CHAIN LINK QUANTITY THE NUMBER OF OUTER SIDE CHAIN LINKS PROVIDED. 1A MODE REPLY 0 BYHZJ 04LENGTH,CHAIN,INNER SIDE INNER SIDE CHAIN LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE INNER SIDE CHAIN,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BYJBA 12QUANTITY,LINK,INNER SIDE CHAIN INNER SIDE CHAIN LINK QUANTITY THE NUMBER OF INNER SIDE CHAIN LINKS PROVIDED. 1A MODE REPLY 0 BYJCG 04SPACING,CHAIN,CROSS CROSS CHAIN SPACING THE SPACING OF THE CROSS CHAINS. FULL TEXT WRITE-IN 0 BYJDJ 10SIZE,WIRE,SIDE CHAIN SIDE CHAIN WIRE SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE SIDE CHAIN WIRE. 2D AND 1B MODE REPLY21AA051AC20 BYJFD 18TYPE,SEAT SEAT TYPE INDICATES THE TYPE OF SEAT PROVIDED. SELECT REPLY CODE 10AK54 BYJGA /D/ 12QUANTITY,PAIRS,TYING TAPE TYING TAPE PAIRS QUANTITY THE NUMBER OF TYING TAPE PAIRS PROVIDED. 1A MODE REPLY 0 BYJHD /D/ 08LOCATION,FASTENER FASTENER LOCATION INDICATES THE LOCATION OF THE FASTENER IN RELATION TO THE ITEM. SELECT REPLY CODE 10AJ91 BYJJD /D/ 07SPLIT,LEG LEG SPLIT AN INDICATION OF WHETHER OR NOT A LEG SPLIT IS INCLUDED. SELECT REPLY CODE 10AA49 BYJKD 18TYPE,SPRING SPRING TYPE INDICATES THE TYPE OF SPRING PROVIDED. SELECT REPLY CODE 10AK54 BYJLD /D/ 07BELT,TIE TIE BELT AN INDICATION OF WHETHER OR NOT A TIE BELT IS INCLUDED. SELECT REPLY CODE 10AA49 BYJMA /D/ 12QUANTITY,PLEAT,BOX BOX PLEAT QUANTITY THE NUMBER OF BOX PLEATS PROVIDED. 1A MODE REPLY 0 BYJNG 19CHARACTERISTICS,FILE FILE CHARACTERISTICS AN INDICATION OF THE CHARACTERISTICS OF THE FILE. FULL TEXT WRITE-IN 0 BYJPD /D/ 07BRUSH,CLEANER,FILE FILE CLEANER BRUSH AN INDICATION OF WHETHER OR NOT A FILE CLEANER BRUSH IS PROVIDED. SELECT REPLY CODE 10AB22 BYJQA 12QUANTITY,HANDLE,SEPARABLE SEPARABLE HANDLE QUANTITY THE NUMBER OF SEPARABLE HANDLES PROVIDED. 1A MODE REPLY 0 BYJRA 03DESIGNATOR,SHAPE,MANUFACTURER MANUFACTURER SHAPE DESIGNATOR THE MANUFACTURER DESIGNATION BY WHICH THE SHAPE OF THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1A MODE REPLY 0 BYJSD 02DESIGN,CUTTER CUTTER DESIGN THE DESIGN OF THE CUTTER. SELECT REPLY CODE 10AK54 BYJTD 14SHAPE,CUTTER CUTTER SHAPE THE PHYSICAL CONFIGURATION OF THE CUTTER. SELECT REPLY CODE 10AD07 BYJWD /D/ 07FEATURE,NOSE,SHORT SHORT NOSE FEATURE AN INDICATION OF WHETHER OR NOT A SHORT NOSE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BYJXD /D/ 07ACTION,LEVER,COMPOUND COMPOUND LEVER ACTION AN INDICATION OF WHETHER OR NOT A COMPOUND LEVER ACTION IS INCLUDED. SELECT REPLY CODE 10AA49 BYJYD /D/ 07NOTCH,STRIPPING STRIPPING NOTCH AN INDICATION OF WHETHER OR NOT A STRIPPING NOTCH IS PROVIDED. SELECT REPLY CODE 10AB22 BYJZD /D/ 07OPENING,SLEEVE SLEEVE OPENING AN INDICATION OF WHETHER OR NOT A SLEEVE OPENING(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BYKBD /D/ 07HOLE,SKINNING SKINNING HOLE AN INDICATION OF WHETHER OR NOT A SKINNING HOLE IS PROVIDED. SELECT REPLY CODE 10AB22 BYKCA 12QUANTITY,REAMER REAMER QUANTITY THE NUMBER OF REAMERS PROVIDED. 1A MODE REPLY 0 BYKDD 18TYPE ACCOMMODATED,FILE FILE TYPE ACCOMMODATED INDICATES THE TYPE OF FILE THE ITEM IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AJ57 BYKFD /D/ 07FEATURE,FLARING,DOUBLE DOUBLE FLARING FEATURE AN INDICATION OF WHETHER OR NOT A DOUBLE FLARING FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BYKGG 19CHARACTERISTICS,REAMER REAMER CHARACTERISTICS AN INDICATION OF THE CHARACTERISTICS OF THE REAMER. FULL TEXT WRITE-IN 0 BYKHD /D/ 07FEATURE,OPERATION,LEFT-HAND LEFT-HAND OPERATION FEATURE AN INDICATION OF WHETHER OR NOT A LEFT-HAND OPERATION FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BYKJD 18TYPE,END,BLADE BLADE END TYPE INDICATES THE TYPE OF BLADE END PROVIDED. SELECT REPLY CODE 10AK84 BYKKD 18TYPE,PATTERN,SINGLE LEVER SINGLE LEVER PATTERN TYPE INDICATES THE TYPE OF SINGLE LEVER PATTERN PROVIDED. SELECT REPLY CODE 10AK54 BYKLD 18TYPE,CUT,COMPOUND LEVER COMPOUND LEVER CUT TYPE INDICATES THE TYPE OF COMPOUND LEVER CUT PROVIDED. SELECT REPLY CODE 10AL18 BYKMJ 04LENGTH ACCOMMODATED,FILE FILE LENGTH ACCOMMODATED A MEASUREMENT OF THE LONGEST DIMENSION OF THE FILE ACCOMMODATED,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BYKND /D/ 07CLOSURE,FLAP FLAP CLOSURE AN INDICATION OF WHETHER OR NOT A FLAP CLOSURE IS PROVIDED. SELECT REPLY CODE 10AB22 BYKPJ 04DIAMETER,BIT BIT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BIT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BYKQJ 04LENGTH,PROJECTION,HOOK HOOK PROJECTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE PROJECTION OF A HOOK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BYKRB 04ANGLE IN DEG,FLARE,PRODUCED PRODUCED FLARE ANGLE IN DEG THE ANGLE OF THE FLARE PRODUCED BY THE ITEM,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BYKSD 07ADAPTER,FLARING,DOUBLE DOUBLE FLARING ADAPTER AN INDICATION OF WHETHER OR NOT A DOUBLE FLARING ADAPTER(S) IS REQUIRED. SELECT REPLY CODE 10AE40 BYKTJ 04DIAMETER ACCOMMODATED,OUTSIDE,DOUBLE FLARING TUBE DOUBLE FLARING TUBE OUTSIDE DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE DOUBLE FLANGE TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BYKWD /D/ 07GAGE,FLARE,ATTACHED ATTACHED FLARE GAGE AN INDICATION OF WHETHER OR NOT AN ATTACHED FLARE GAGE IS PROVIDED. SELECT REPLY CODE 10AB22 BYKXD 18TYPE FOR WHICH DESIGNED,GROMMET GROMMET TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF GROMMET FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AC40 BYKYJ 04HEIGHT,POCKET POCKET HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A POCKET,IN DISTICTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 BYKZJ 04WIDTH,POCKET POCKET WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A POCKET,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BYLBA 12QUANTITY,DRAWER,COMPARTMENTED COMPARTMENTED DRAWER QUANTITY THE NUMBER OF DRAWERS COMPARTMENTED. 1A MODE REPLY 0 BYLCA 12QUANTITY PER DRAWER,COMPARTMENT COMPARTMENT QUANTITY PER DRAWER THE NUMBER OF COMPARTMENTS IN EACH INDIVIDUAL DRAWER. 1A MODE REPLY 0 BYLDD /D/ 07TILL,TOP TOP TILL AN INDICATION OF WHETHER OR NOT A TOP TILL IS PROVIDED. SELECT REPLY CODE 10AB22 BYLFD /D/ 07FRONT,PANEL PANEL FRONT AN INDICATION OF WHETHER OR NOT A PANEL FRONT IS PROVIDED. SELECT REPLY CODE 10AB22 BYLGG 18TYPE AND QUANTITY,FACILITY,CLOSING CLOSING FACILITY TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF THE CLOSING FACILITY/IES/ PROVIDED. FULL TEXT WRITE-IN 0 BYLHD 18TYPE,LOCK LOCK TYPE INDICATES THE TYPE OF LOCK PROVIDED. SELECT REPLY CODE 10AE36 BYLJG /D/ 04SIZE,CROSS-SECTIONAL,BODY BODY CROSS-SECTIONAL SIZE DESIGNATES THE SIZE OF THE BODY WHEN VIEWED IN CROSS SECTION. FULL TEXT WRITE-IN 0 BYLKD /D/ 07DEVICE,FASTENING,BELT BELT FASTENING DEVICE AN INDICATION OF WHETHER OR NOT A BELT FASTENING DEVICE IS PROVIDED. SELECT REPLY CODE 10AB22 BYLLJ 04RADIUS,BEADING BEADING RADIUS THE DISTANCE FROM THE CENTERLINE TO THE AXIS OF THE BEADING. 2D AND 1B MODE REPLY21AA051AC20 BYLMD 02DESIGN,CUPPED CUPPED DESIGN THE DESIGN OF A CUPPED ITEM. SELECT REPLY CODE 10AN46 BYLNJ /D/ 04DISTANCE FROM LUG MOUNTING HOLE CENTER TO BASE DISTANCE FROM LUG MOUNTING HOLE CENTER TO BASE NONE. 2D AND 1B MODE REPLY21AA051AC20 BYLPJ 04WIDTH,LUG,MOUNTING MOUNTING LUG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYLQJ /D/ 04WIDTH,OPENING,LUG LUG OPENING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYLRJ 04THICKNESS,MATERIAL,BUCKLE BUCKLE MATERIAL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BYLSJ /D/ 04SIZE FOR WHICH DESIGNED,SCREW SCREW SIZE FOR WHICH DESIGNED NONE. 2D AND 1B MODE REPLY21AA051AC20 BYLTJ 04LENGTH,OVERALL,SHORT LEG SHORT LEG OVERALL LENGTH A DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE SHORT LEG. 2D AND 1B MODE REPLY21AA051AC20 BYLWJ 04LENGTH,OVERALL,LONG LEG LONG LEG OVERALL LENGTH A DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE LONG LEG. 2D AND 1B MODE REPLY21AA051AC20 BYLXD 18TYPE FOR WHICH DESIGNED,STRAPPING STRAPPING TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF STRAPPING FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BYLYD /D/ 07EARS EARS AN INDICATION OF WHETHER OR NOT EARS ARE INCLUDED. SELECT REPLY CODE 10AA49 BYLZJ 04WIDTH FOR WHICH DESIGNED,STRAPPING STRAPPING WIDTH FOR WHICH DESIGNED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE STRAPPING WIDTH FOR WHICH THE ITEM IS DESIGNED, IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BYMBD /D/ 19EQUIPMENT FOR WHICH DESIGNED,SEALING SEALING EQUIPMENT FOR WHICH DESIGNED THE SEALING EQUIPMENT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BYMCG 19NAME,TOOL,SEALING SEALING TOOL NAME THE NAME ASSIGNED TO THE SEALING TOOL BY THE CONTROLLING AGENCY. FULL TEXT WRITE-IN 0 BYMDA 19NUMBER,MODEL,SEALING TOOL SEALING TOOL MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE SEALING TOOL. 1A MODE REPLY 0 BYMFG /D/ 19NAME,MACHINE,STRETCHING/SEALING STRETCHING/SEALING MACHINE NAME THE NAME ASSIGNED TO THE STRETCHING AND SEALING MACHINE BY THE CONTROLLING AGENCY. FULL TEXT WRITE-IN 0 BYMGA /D/ 19NUMBER,MODEL,STRETCHING/SEALING MACHINE STRETCHING/SEALING MACHINE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE STRETCHING AND SEALING MACHINE. 1A MODE REPLY 0 BYMHD 01COLOR,BODY BODY COLOR THE HUE OR TINT OF THE BODY. SELECT REPLY CODE 10AD06 BYMJD /D/ 07INSIGNIA INSIGNIA AN INDICATION OF WHETHER OR NOT AN INSIGNIA(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BYMKJ 04LENGTH,OPENING,LOOP LOOP OPENING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE LOOP OPENING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BYMLJ 10SIZE,HOLE,MOUNTING MOUNTING HOLE SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSION OF THE MOUNTING HOLE. 2D AND 1B MODE REPLY21AA051AC20 BYMMJ 04DISTANCE BETWEEN BASE AND INSIDE OF ARCH DISTANCE BETWEEN BASE AND INSIDE OF ARCH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYMNJ 04DISTANCE BETWEEN BASE AND INSIDE OF LARGE ARCH DISTANCE BETWEEN BASE AND INSIDE OF LARGE ARCH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYMPJ /D/ 04DIAMETER/ARCH LENGTH,INSIDE INSIDE DIAMETER/ARCH LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYMQJ /D/ 04DIAMETER/LARGE ARCH LENGTH,INSIDE INSIDE DIAMETER/LARGE ARCH LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYMRJ 04DISTANCE BETWEEN ARCH AND MOUNTING HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN ARCH AND MOUNTING HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BYMSJ 04DISTANCE BETWEEN LARGE ARCH AND MOUNTING HOLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN LARGE ARCH AND MOUNTING HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 BYMTJ 04DISTANCE BETWEEN MOUNTING HOLE CENTER AND INSIDE EDGE OF ARCH DISTANCE BETWEEN MOUNTING HOLE CENTER AND INSIDE EDGE OF ARCH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYMWA 12QUANTITY,ARCH ARCH QUANTITY NONE. 1A MODE REPLY 0 BYMXJ 04DISTANCE BETWEEN BASE AND END OF ARCH PROTRUDING PORTION DISTANCE BETWEEN BASE AND END OF ARCH PROTRUDING PORTION NONE. 2D AND 1B MODE REPLY21AA051AC20 BYMYJ 04DISTANCE BETWEEN CENTER OF MOUNTING HOLE AND ARCH END DISTANCE BETWEEN CENTER OF MOUNTING HOLE AND ARCH END NONE. 2D AND 1B MODE REPLY21AA051AC20 BYMZJ 04RADIUS,ARCH ARCH RADIUS A MEASUREMENT OF A STRAIGHT LINE EXTENDING FROM THE CENTERLINE TO THE ARCH END. 2D AND 1B MODE REPLY21AA051AC20 BYNBJ 04DISTANCE BETWEEN HOLE CENTER AND OUTSIDE EDGE OF RETAINING HOOK DISTANCE BETWEEN HOLE CENTER AND OUTSIDE EDGE OF RETAINING HOOK NONE. 2D AND 1B MODE REPLY21AA051AC20 BYNCJ 04DIAMETER,HOLE,RETAINING HOOK RETAINING HOOK HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BYNDJ 10TOLERANCE,SETTING,TEMP TEMP SETTING TOLERANCE THE PERMISSIBLE TEMPERATURE DEVIATION FROM THE SPECIFIED SETTING. 2D AND 1B MODE REPLY21AB361AC20 BYNFA /D/ 12QUANTITY,FENESTRATION FENESTRATION QUANTITY THE NUMBER OF FENESTRATIONS PROVIDED. 1A MODE REPLY 0 BYNGD 14SHAPE,CROSS-SECTIONAL,BLADE BLADE CR0SS-SECTIONAL SHAPE THE PHYSICAL CONFIGURATION OF THE BLADE WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 BYNHJ 04WIDTH,TANG TANG WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TANG,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BYNJD 18TYPE,POINT,BLADE BLADE POINT TYPE INDICATES THE TYPE OF BLADE POINT(S) PROVIDED. SELECT REPLY CODE 10AJ44 BYNKD /D/ 08LOCATION,SURFACE,BLADE CUTTING BLADE CUTTING SURFACE LOCATION INDICATES THE LOCATION OF THE CUTTING SURFACE ON THE BLADE. SELECT REPLY CODE 10AJ91 BYNLG 04SIZE,BLADE BLADE SIZE THE RECOGNIZED TRADE DESIGNATION OR TERM INDICATING THE BLADE SIZE. FULL TEXT WRITE-IN 0 BYNMA 12QUANTITY,BLADE,MOVABLE MOVABLE BLADE QUANTITY THE NUMBER OF BLADES THAT CAN BE MOVED OR REPOSITIONED. 1A MODE REPLY 0 BYNNJ 10CAPACITY,STRUCK STRUCK CAPACITY THE STRUCK CAPACITY FOR WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY12AG67 BYNPJ 10SPEED,HAULING,MAXIMUM MAXIMUM HAULING SPEED THE MAXIMUM SPEED AT WHICH THE ITEM IS RATED FOR HAULING. 1D AND 1B MODE REPLY11AA22 BYNQG 19NAME,MANUFACTURER,TRACTOR TRACTOR MANUFACTURER NAME THE NAME OF THE MANUFACTURER OF THE TRACTOR. FULL TEXT WRITE-IN 0 BYNRA 19NAME,TRACTOR TRACTOR NAME THE NOMENCLATURE BY WHICH THE TRACTOR IS IDENTIFIED. 1A MODE REPLY 0 BYNSG 19NUMBER,IDENTIFYING,TRACTOR TRACTOR IDENTIFYING NUMBER THE IDENTIFICATION NUMBER OF THE TRACTOR. FULL TEXT WRITE-IN 0 BYNTG 19NAME,MANUFACTURER,TRAILER TRAILER MANUFACTURER NAME THE NAME OF THE MANUFACTURER OF THE TRAILER. FULL TEXT WRITE-IN 0 BYNWG 19NUMBER,IDENTIFYING,TRAILER TRAILER IDENTIFYING NUMBER THE IDENTIFICATION NUMBER OF THE TRAILER. FULL TEXT WRITE-IN 0 BYNXJ T10RANGE,SPEED SPEED RANGE THE MINIMUM TO MAXIMUM SPEED OF THE ITEM. 1D AND 1F MODE REPLY12AJ20 BYNYD /D/ 19NAME,CLOTH,WOVEN WOVEN CLOTH NAME THE TERM/S/ BY WHICH THE WOVEN CLOTH IS KNOWN OR DESIGNATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AF82 BYNZD /D/ 07SHOULDER,CAP CAP SHOULDER AN INDICATION OF WHETHER OR NOT A CAP SHOULDER/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BYPBD /D/ 11METHOD,FABRICATION,COLLARETTE/WRISTLET COLLARETTE/WRISTLET FABRICATION METHOD THE MEANS USED IN MANUFACTURING THE COLLARETTE(S) AND WRISTLET(S). SELECT REPLY CODE 10AK54 BYPCJ /D/ 04SIZE,CHEST CHEST SIZE DESIGNATES THE CHEST SIZE. 2D AND 1B MODE REPLY21AA051AC20 BYPDD /D/ 18TYPE,SEAT,GARMENT GARMENT SEAT TYPE INDICATES THE TYPE OF GARMENT SEAT PROVIDED. SELECT REPLY CODE 10AK54 BYPFD /D/ 07FEATURE,CLOSURE,FLAP/BUTTON FLAP/BUTTON CLOSURE FEATURE AN INDICATION OF WHETHER OR NOT A FLAP AND BUTTON CLOSURE FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BYPGD 18TYPE,YOKE YOKE TYPE INDICATES THE TYPE OF YOKE(S) PROVIDED. SELECT REPLY CODE 10AK54 BYPHJ /D/ 04LENGTH,BACK,CENTER CENTER BACK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CENTER BACK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BYPJD /D/ 11METHOD,CLOSING,NECK NECK CLOSING METHOD THE MEANS BY WHICH THE NECK IS CLOSED. SELECT REPLY CODE 10AK54 BYPKD /D/ 11METHOD,FABRICATION,MATERIAL MATERIAL FABRICATION METHOD THE MEANS USED IN MANUFACTURING THE MATERIAL. SELECT REPLY CODE 10AK54 BYPLD /D/ 01COLOR,CUFF CUFF COLOR THE HUE OR TINT OF THE CUFF. SELECT REPLY CODE 10AD06 BYPMA /D/ 19IDENTIFICATION,SHADE,CUFF CUFF SHADE IDENTIFICATION A DESIGNATION ASSIGNED TO A PARTICULAR GRADATION OF A COLOR FOR PURPOSE OF READY IDENTIFICATION OF THE CUFF SHADE. 1A MODE REPLY 0 BYPND /D/ 19SOURCE,SHADE,CUFF CUFF SHADE SOURCE THE NAME OF THE GOVERNMENT AGENCY,COMMERCIAL ORGANIZATION,OR MANUFACTURER CONTROLLING THE CUFF SHADE DESIGNATOR. SELECT REPLY CODE 10AF94 BYPPD /D/ 13THREAD SERIES,ACCOMMODATION,PRIMARY TERMINAL PRIMARY TERMINAL ACCOMMODATION THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF A PRIMARY TERMINAL ACCOMMODATION. SELECT REPLY CODE 10AH06 BYPRD /D/ 07BUTTON BUTTON AN INDICATION OF WHETHER OR NOT A BUTTON/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 BYPSD /D/ 18TYPE,STITCH,BODY BODY STITCH TYPE INDICATES THE TYPE OF BACK STITCH PROVIDED. SELECT REPLY CODE 10AK54 BYPTD /D/ 18TYPE,STITCH,WAISTBAND WAISTBAND STITCH TYPE INDICATES THE TYPE OF WAISTBAND STITCH PROVIDED. SELECT REPLY CODE 10AK54 BYPWD /D/ 18TYPE,STITCH,CUFF CUFF STITCH TYPE INDICATES THE TYPE OF CUFF STITCH PROVIDED. SELECT REPLY CODE 10AK54 BYPXD /D/ 18TYPE,STITCH,COLLAR COLLAR STITCH TYPE INDICATES THE TYPE OF COLLAR STITCH PROVIDED. SELECT REPLY CODE 10AK54 BYPYD /D/ 18TYPE,STITCH,SLEEVE SLEEVE STITCH TYPE INDICATES THE TYPE OF SLEEVE STITCH PROVIDED. SELECT REPLY CODE 10AK54 BYPZD /D/ 18TYPE,STITCH,NECK NECK STITCH TYPE INDICATES THE TYPE OF NECK STITCH PROVIDED. SELECT REPLY CODE 10AK54 BYQBD /D/ 18TYPE,STITCH,YOKE YOKE STITCH TYPE INDICATES THE TYPE OF YOKE STITCH PROVIDED. SELECT REPLY CODE 10AK54 BYQCD /D/ 18TYPE,GARMENT,UPPER UPPER GARMENT TYPE INDICATES THE TYPE OF UPPER GARMENT FURNISHED. SELECT REPLY CODE 10AK54 BYQDD 02DESIGN,GARMENT,UPPER UPPER GARMENT DESIGN THE DESIGN OF THE BODY OF THE UPPER GARMENT,EXCLUDING THE TYPE OF SLEEVES,CUFFS,COLLAR,AND THE LIKE. SELECT REPLY CODE 10AK54 BYQFD /D/ 11METHOD,CLOSING,UPPER GARMENT UPPER GARMENT CLOSING METHOD THE MEANS BY WHICH THE PRINCIPAL OPENING OF THE UPPER GARMENT IS CLOSED. SELECT REPLY CODE 10AK54 BYQGD /D/ 18TYPE,LEG,TROUSER TROUSER LEG TYPE INDICATES THE TYPE OF TROUSER LEG PROVIDED. SELECT REPLY CODE 10AK54 BYQHD /D/ 11METHOD,CLOSURE,TROUSER LEG TROUSER LEG CLOSURE METHOD THE MEANS BY WHICH THE TROUSER LEG IS CLOSED. SELECT REPLY CODE 10AF69 BYQJD /D/ 07FEATURE,STRAP,SHOE,TROUSER LEG TROUSER LEG SHOE STRAP FEATURE AN INDICATION OF WHETHER OR NOT A TROUSER LEG SHOE STRAP FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BYQKD /D/ 11METHOD,SUPPORT,TROUSER TROUSER SUPPORT METHOD THE MEANS BY WHICH THE TROUSERS ARE SUPPORTED. SELECT REPLY CODE 10AF69 BYQLD /D/ 09MATERIAL,LINING,TROUSER TROUSER LINING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TROUSER LINING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BYQMD /D/ 02DESIGN,HEADWEAR HEADWEAR DESIGN THE DESIGN OF THE HEAD COVERING. SELECT REPLY CODE 10AK54 BYQND /D/ 17SURFACE TREATMENT,PANEL PANEL SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A PANEL SURFACE. SELECT REPLY CODE 10AD09 BYQPA /D/ 12QUANTITY PER OPENING,DOOR DOOR QUANTITY PER OPENING THE NUMBER OF DOORS IN EACH OPENING. 1A MODE REPLY 0 BYQQD /D/ 07GLASS,DOOR,FITTED FITTED DOOR GLASS AN INDICATION OF WHETHER OR NOT A FITTED DOOR GLASS IS INCLUDED. SELECT REPLY CODE 10AA49 BYQRD /D/ 18TYPE,GLASS,DOOR DOOR GLASS TYPE INDICATES THE TYPE OF DOOR GLASS PROVIDED. SELECT REPLY CODE 10AF82 BYQSD /D/ 07SCREEN,DOOR,FITTED FITTED DOOR SCREEN AN INDICATION OF WHETHER OR NOT A FITTED DOOR SCREEN IS INCLUDED. SELECT REPLY CODE 10AA49 BYQWA /D/ 12QUANTITY PER OPENING,SASH,WINDOW WINDOW SASH QUANTITY PER OPENING THE NUMBER OF WINDOW SASHES PER OPENING PROVIDED. 1A MODE REPLY 0 BYQXA /D/ 16STYLE,END,EYE EYE END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE EYE END. 1A MODE REPLY 0 BYQYJ 10LIFT,RATED RATED LIFT A MEASUREMENT OF THE LIFT FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY21AA051AC20 BYQZD 18TYPE FOR WHICH DESIGNED,SHANK,BLADE BLADE SHANK TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF BLADE SHANK FOR WHICH DESIGNED. SELECT REPLY CODE 10AH09 BYRBD /D/ 09MATERIAL,COATING,UPPER FOOTWEAR UPPER FOOTWEAR COATING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE,WITH WHICH THE UPPER FOOTWEAR IS COATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BYRCD 18TYPE,END,CONNECTION CONNECTION END TYPE INDICATES THE TYPE OF CONNECTION END ON THE ITEM. SELECT REPLY CODE 10AB76 BYRDD /D/ 09MATERIAL,SUPPORT,FRONT LINING,INSIDE LEGGING INSIDE LEGGING FRONT LINING SUPPORT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LINING SUPPORT INSIDE LEGGING FRONT IS FABRICATED. SELECT REPLY CODE 10AD09 BYRFD /D/ 09MATERIAL BETWEEN LEG FRONT AND LINING,SUPPORT,INTERLINING INTERLINING SUPPORT MATERIAL BETWEEN LEG FRONT AND LINING THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INTERLINING SUPPORT BETWEEN LEG FRONT AND LINING IS FABRICATED. SELECT REPLY CODE 10AD09 BYRGD /D/ 07STRAP,STIRRUP STIRRUP STRAP AN INDICATION OF WHETHER OR NOT A STIRRUP STRAP(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BYRHD /D/ 07STRAP,GROUNDING,CONDUCTIVE CONDUCTIVE GROUNDING STRAP AN INDICATION OF WHETHER OR NOT A CONDUCTIVE GROUNDING STRAP IS INCLUDED. SELECT REPLY CODE 10AA49 BYRJD /D/ 07FEATURE,STERILIZABLE STERILIZABLE FEATURE AN INDICATION OF WHETHER OR NOT A STERILIZABLE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BYRKA /D/ 03DESIGNATION,DENIER DENIER DESIGNATION A DESIGNATION OF A UNIT OF FINENESS FOR SILK,RAYON,OR NYLON YARN EQUAL TO THE FINENESS OF A YARN WEIGHING ONE GRAM FOR EACH NINE THOUSAND METERS. 1A MODE REPLY 0 BYRLD /D/ 09MATERIAL,COVERING,PROTECTIVE,SHOE TOP/SIDE SHOE TOP/SIDE PROTECTIVE COVERING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PROTECTIVE COVERING FOR SHOE TOP AND/OR SIDE IS FABRICATED. SELECT REPLY CODE 10AD09 BYRMB /D/ 10PERCENTAGE,MATERIAL,BASIC BASIC MATERIAL PERCENTAGE THE PERCENTAGE OF MATERIALS USED IN THE ITEM. 1B MODE REPLY 0 BYRNA /D/ 03DESIGNATION,GAGE GAGE DESIGNATION A DESIGNATION OF THE FINENESS OF A KNITTED FABRIC IN LOOPS PER ONE AND A HALF INCHES. 1A MODE REPLY 0 BYRPJ /D/ 10WEIGHT PER DOZEN PAIR WEIGHT PER DOZEN PAIR THE WEIGHT WHEN THE ITEM IS NORMALLY SUPPLIED IN LOTS OF A DOZEN PAIR. 1D AND 1B MODE REPLY12AG67 BYRQD /D/ 04LENGTH,LEG,GARMENT GARMENT LEG LENGTH THE LEG LENGTH OF THE GARMENT. SELECT REPLY CODE 10AF81 BYRRD /D/ 09MATERIAL,CORD,LACING LACING CORD MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LACING CORD IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BYRSD /D/ 09MATERIAL,TAPE,ADJUSTMENT ADJUSTMENT TAPE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ADJUSTMENT TAPE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BYRTD /D/ 08LOCATION,TAPE,DRAW DRAW TAPE LOCATION INDICATES THE LOCATION OF THE DRAW TAPE IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 BYRWD /D/ 08LOCATION,CORD,LACING LACING CORD LOCATION INDICATES THE LOCATION OF THE LACING CORD IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 BYRXA /D/ 12QUANTITY,POCKET,LEFT LEGGING LEFT LEGGING POCKET QUANTITY THE NUMBER OF POCKETS INCLUDED IN THE LEFT LEGGING. 1A MODE REPLY 0 BYRYD /D/ 18TYPE,POCKET,LEFT LEGGING LEFT LEGGING POCKET TYPE INDICATES THE TYPE OF POCKET ON THE LEFT LEGGING. SELECT REPLY CODE 10AF87 BYRZJ /D/ 04DEPTH,POCKET,LEFT LEGGING LEFT LEGGING POCKET DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE LEFT LEGGING POCKET,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 BYSBJ /D/ 04WIDTH,POCKET,LEFT LEGGING LEFT LEGGING POCKET WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A LEFT LEGGING POCKET,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BYSCD /D/ 08LOCATION,POCKET,LEFT LEGGING LEFT LEGGING POCKET LOCATION INDICATES THE LOCATION OF THE POCKET IN OR ON THE LEFT LEGGING. SELECT REPLY CODE 10AJ91 BYSDD /D/ 11METHOD,CLOSING,LEFT LEGGING POCKET LEFT LEGGING POCKET CLOSING METHOD THE MEANS BY WHICH THE LEFT LEGGING POCKET OPENING IS CLOSED. SELECT REPLY CODE 10AF69 BYSFA /D/ 12QUANTITY,POCKET,RIGHT LEGGING RIGHT LEGGING POCKET QUANTITY THE NUMBER OF POCKETS INCLUDED IN THE RIGHT LEGGING. 1A MODE REPLY 0 BYSGD /D/ 18TYPE,POCKET,RIGHT LEGGING RIGHT LEGGING POCKET TYPE INDICATES THE TYPE OF POCKET ON THE RIGHT LEGGING. SELECT REPLY CODE 10AF87 BYSHJ /D/ 04DEPTH,POCKET,RIGHT LEGGING RIGHT LEGGING POCKET DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE RIGHT LEGGING POCKET,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 BYSJJ /D/ 04WIDTH,POCKET,RIGHT LEGGING RIGHT LEGGING POCKET WIDTH THE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A RIGHT LEGGING POCKET,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BYSKD /D/ 08LOCATION,POCKET,RIGHT LEGGING RIGHT LEGGING POCKET LOCATION INDICATES THE LOCATION OF THE POCKET IN OR ON THE RIGHT LEGGING. SELECT REPLY CODE 10AJ91 BYSLD /D/ 07TAB,PULL PULL TAB AN INDICATION OF WHETHER OR NOT A PULL TAB IS INCLUDED. SELECT REPLY CODE 10AA49 BYSMD /D/ 09MATERIAL,REINFORCING,STIRRUP STIRRUP REINFORCING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE STIRRUP REINFORCING MATERIAL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BYSND /D/ 08LOCATION,PLEAT,BOX BOX PLEAT LOCATION INDICATES THE LOCATION OF THE BOX PLEATS IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 BYSPD /D/ 18TYPE,PLAID PLAID TYPE INDICATES THE PLAID TYPE PATTERNED TO DESIGNATE A DISTINCTIVE CLAN. SELECT REPLY CODE 10AF83 BYSQD /D/ 02DESIGN,SKIRT SKIRT DESIGN THE DESIGN OF THE SKIRT. SELECT REPLY CODE 10AC48 BYSRD 18TYPE,FASTENER,BELT BELT FASTENER TYPE INDICATES THE TYPE OF BELT FASTENER. SELECT REPLY CODE 10AF69 BYSSA /D/ 12QUANTITY,GORE GORE QUANTITY THE NUMBER OF GORES PROVIDED. 1A MODE REPLY 0 BYSTA /D/ 12QUANTITY,PLEAT PLEAT QUANTITY THE NUMBER OF PLEATS PROVIDED. 1A MODE REPLY 0 BYSWD /D/ 18TYPE,PLEAT PLEAT TYPE INDICATES THE TYPE OF PLEAT(S) PROVIDED. SELECT REPLY CODE 10AK54 BYSXD /D/ 08LOCATION,PLEAT PLEAT LOCATION INDICATES THE LOCATION OF THE PLEAT(S) IN RELATION TO THE ITEM. SELECT REPLY CODE 10AJ91 BYSYJ /D/ 04LENGTH,SLIT SLIT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SLIT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BYSZD /D/ 08LOCATION,SLIT SLIT LOCATION INDICATES THE LOCATION OF THE SLIT IN RELATION TO THE ITEM. SELECT REPLY CODE 10AJ91 BYTBD /D/ 07FEATURE,PRESHRUNK PRESHRUNK FEATURE AN INDICATION OF WHETHER OR NOT A PRESHRUNK FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BYTCD /D/ 07SKIRT SKIRT AN INDICATION OF WHETHER OR NOT A SKIRT IS INCLUDED. SELECT REPLY CODE 10AA49 BYTDD /D/ 11METHOD,SUPPORT,BRASSIERE BRASSIERE SUPPORT METHOD THE MEANS PROVIDED FOR SUPPORTING THE BRASSIERE. SELECT REPLY CODE 10AH72 BYTFD /D/ 11METHOD,SUPPORT,SKIRT SKIRT SUPPORT METHOD THE MEANS USED FOR SUPPORTING THE SKIRT. SELECT REPLY CODE 10AH72 BYTGD /D/ 07FEATURE,USAGE,ASPHALT SURFACE ASPHALT SURFACE USAGE FEATURE AN INDICATION OF WHETHER OR NOT AN ASPHALT SURFACE USAGE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BYTHD /D/ 03DESIGNATOR,USER,RESTRICTED RESTRICTED USER DESIGNATOR A DESIGNATION INDICATING THE PERSONNEL,ORGANIZATION,PROFESSION,TRADE,AND THE LIKE,TO WHICH THE ITEM IS RESTRICTED. SELECT REPLY CODE 10AL31 BYTJD 07USAGE,WATER WATER USAGE AN INDICATION OF WHETHER OR NOT WATER IS REQUIRED FOR USE WITH THE ITEM. SELECT REPLY CODE 10AE40 BYTKB /D/ 10PERCENTAGE,SUBSTANCE,ACTIVE ENZYME/BACTERIAL ACTIVE ENZYME/BACTERIAL SUBSTANCE PERCENTAGE THE PERCENTAGE OF ACTIVE ENZYME AND/OR BACTERIAL SUBSTANCE OF THE ITEM. 1B MODE REPLY 0 BYTLD /D/ 07FEATURE,SELF-POLISHING SELF-POLISHING FEATURE AN INDICATION OF WHETHER OR NOT A SELF-POLISHING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BYTMD 01COLOR,SURFACE,IMPARTED IMPARTED SURFACE COLOR THE HUE OR TINT IMPARTED TO THE SURFACE. SELECT REPLY CODE 10AD06 BYTND /D/ 07FEATURE,NONFREEZING NONFREEZING FEATURE AN INDICATION OF WHETHER OR NOT A NONFREEZING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BYTPD /D/ 18TYPE,MATERIAL MATERIAL TYPE INDICATES THE TYPE OF MATERIAL COMPOSING THE ITEM. SELECT REPLY CODE 10AJ06 BYTQG 10PERCENTAGE BY WEIGHT,COMPOSITION COMPOSITION PERCENTAGE BY WEIGHT THE ELEMENTS USED IN THE COMPOSITION OF THE ITEM,EXPRESSED IN PERCENTAGE BY WEIGHT. FULL TEXT WRITE-IN 0 BYTRB /D/ 10ALKALINITY IN PERCENT,MINIMUM,SODIUM OXIDE SODIUM OXIDE MINIMUM ALKALINITY IN PERCENT THE MINIMUM ALKALINITY AS SODIUM OXIDE,EXPRESSED IN PERCENT. 1B MODE REPLY 0 BYTSH /D/ 09MATERIAL AND LOCATION,LINING,PARTIAL PARTIAL LINING MATERIAL AND LOCATION THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PARTIAL LINING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT,AND ITS LOCATION. 2D MODE REPLY 26AD093AJ91 BYTTD /D/ 01COLOR,INSERT INSERT COLOR THE HUE OR TINT OF THE INSERT. SELECT REPLY CODE 10AD06 BYTWD 18TYPE,CUFF CUFF TYPE INDICATES THE TYPE OF CUFF(S) PROVIDED. SELECT REPLY CODE 10AF69 BYTXD 18TYPE,MATERIAL,FILTERING FILTERING MATERIAL TYPE INDICATES THE TYPE OF FILTERING MATERIAL PROVIDED. SELECT REPLY CODE 10AN27 BYTYD /D/ 07FEATURE FOR LEVER LOCKING DEVICE,DRILLED DRILLED FEATURE FOR LEVER LOCKING DEVICE AN INDICATION OF WHETHER OR NOT A DRILLED FEATURE FOR A LEVER LOCKING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 BYTZD /D/ 08LOCATION,RESISTOR RESISTOR LOCATION INDICATES THE LOCATION OF THE RESISTOR(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 BYWBD /D/ 07LOOP,ASSEMBLY,HARNESS,ATTACHING ATTACHING HARNESS ASSEMBLY LOOP AN INDICATION OF WHETHER OR NOT A LOOP FOR ATTACHING THE HARNESS ASSEMBLY IS INCLUDED. SELECT REPLY CODE 10AA49 BYWCD /D/ 07FEATURE,CUT,GUNN GUNN CUT FEATURE AN INDICATION OF WHETHER OR NOT A GUNN CUT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BYWDA /D/ 12QUANTITY,SHEATH,TOTAL FINGER TOTAL FINGER SHEATH QUANTITY THE TOTAL NUMBER OF FINGER SHEATHS PROVIDED. 1A MODE REPLY 0 BYWFA /D/ 12QUANTITY EXCLUDING THUMB,SHEATH,FINGER FINGER SHEATH QUANTITY EXCLUDING THUMB THE NUMBER OF FINGER SHEATHS PROVIDED,EXCLUDING THE THUMB. 1A MODE REPLY 0 BYWGA /D/ 03DESIGNATOR,SHEATHED,FINGER FINGER SHEATHED DESIGNATOR A DESIGNATION OF THE SHEATHED FINGERS ON THE ITEM. 1A MODE REPLY 0 BYWHD /D/ 09MATERIAL,STRAP,TAKEUP TAKEUP STRAP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TAKEUP STRAP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BYWJD /D/ 07CUFF,GAUNTLET,FABRIC FACED FABRIC FACED GAUNTLET CUFF AN INDICATION OF WHETHER OR NOT A FABRIC FACED GAUNTLET CUFF IS INCLUDED. SELECT REPLY CODE 10AA49 BYWKJ /D/ 10CIRCUMFERENCE,PALM PALM CIRCUMFERENCE A MEASUREMENT OF THE EXTERNAL BOUNDARY OR SURFACE OF A PALM. 2D AND 1B MODE REPLY21AA051AC20 BYWLJ /D/ 04LENGTH,HAND HAND LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE HAND,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BYWMD /D/ 03DESIGNATION,LENGTH LENGTH DESIGNATION A DESIGNATION WHICH SERVES TO IDENTIFY THE LENGTH OF AN ITEM. SELECT REPLY CODE 10AK95 BYWND /D/ 09MATERIAL,MULTILAYER MULTILAYER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MULTILAYER MATERIAL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BYWPG /D/ 19SPEC/STD,MATERIAL,MULTILAYER MULTILAYER MATERIAL SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE MULTILAYER MATERIAL. FULL TEXT WRITE-IN 0 BYWQD /D/ 07IMPREGNATION,LUBRICANT,MATERIAL MATERIAL LUBRICANT IMPREGNATION AN INDICATION OF WHETHER OR NOT A MATERIAL LUBRICANT IMPREGNATION IS INCLUDED. SELECT REPLY CODE 10AA49 BYWRJ /D/ 10AXIS,MAJOR,INSIDE INSIDE MAJOR AXIS NONE. 2D AND 1B MODE REPLY21AA051AC20 BYWSJ /D/ 10AXIS,MINOR,INSIDE INSIDE MINOR AXIS NONE. 2D AND 1B MODE REPLY21AA051AC20 BYWTA /D/ 12QUANTITY ALONG R DIMENSION,HOLE,BOLT BOLT HOLE QUANTITY ALONG R DIMENSION NONE. 1A MODE REPLY 0 BYWWJ 04DIAMETER,HOLE,BOLT,SMALLEST SMALLEST BOLT HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BYWXJ 04DIAMETER,HOLE,BOLT,LARGEST LARGEST BOLT HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BYWYJ /D/ 10PITCH PITCH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYWZB 04ANGLE IN DEG,BEVEL,INSIDE INSIDE BEVEL ANGLE IN DEG NONE. 1B MODE REPLY 0 BYXBJ 04WIDTH,CUTOUT CUTOUT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYXCJ 04DEPTH,SEAT,BALL BALL SEAT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYXDJ 04WIDTH,PORTION,STRAIGHT BODY STRAIGHT BODY PORTION WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYXFJ 04WIDTH,FLANGE,SMALLER SMALLER FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYXGJ 04DIAMETER,INSIDE,STRAIGHT BORE STRAIGHT BORE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BYXHJ 04DEPTH,BORE,STRAIGHT STRAIGHT BORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYXJJ 04WIDTH,SERRATION SERRATION WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYXKJ 04DIAMETER,SHOULDER,EXTERNAL EXTERNAL SHOULDER DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BYXLJ 04DEPTH,SHOULDER,EXTERNAL EXTERNAL SHOULDER DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYXMJ /D/ 04DIAMETER,RECESS,OPPOSITE BORE OPPOSITE BORE RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BYXNJ /D/ 04DEPTH,RECESS,BORE,OPPOSITE OPPOSITE BORE RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BYXPJ 04DIAMETER,SHOULDER,INTERNAL INTERNAL SHOULDER DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BYXQJ 04THICKNESS,SHOULDER,INTERNAL INTERNAL SHOULDER THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 BYXRJ 04DIAMETER,OUTSIDE,MAXIMUM,BODY BODY MAXIMUM OUTSIDE DIAMETER NONE. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 1D AND 1B MODE REPLY11AA05 BYXSJ 04DIAMETER,OUTSIDE,MINIMUM,BODY BODY MINIMUM OUTSIDE DIAMETER NONE.MRC DISCONTINURED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 1D AND 1B MODE REPLY11AA05 BYXTJ /D/ 04DIAMETER,MAJOR,MAXIMUM,TAPERED BORE TAPERED BORE MAXIMUM MAJOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BYXWJ /D/ 04DIAMETER,MAJOR,MINIMUM,TAPERED BORE TAPERED BORE MINIMUM MAJOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BYXXJ /D/ 04DIAMETER,MINOR,MAXIMUM,TAPERED BORE TAPERED BORE MAXIMUM MINOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BYXYJ /D/ 04DIAMETER,MINOR,MINIMUM,TAPERED BORE TAPERED BORE MINIMUM MINOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BYXZJ /D/ 04DIAMETER,MAXIMUM,END INTERNAL BEVEL END INTERNAL BEVEL MAXIMUM DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BYYBJ /D/ 04DIAMETER,MINIMUM,END INTERNAL BEVEL END INTERNAL BEVEL MINIMUM DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BYYCJ /D/ 04DIAMETER,MAXIMUM,BODY MINOR TAPER BODY MINOR TAPER MAXIMUM DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BYYDJ /D/ 04DIAMETER,MINIMUM,BODY MINOR TAPER BODY MINOR TAPER MINIMUM DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BYYFB 04TAPER IN DEG,BORE BORE TAPER IN DEG NONE. 1B MODE REPLY 0 BYYGJ /D/ 04ANGLE IN DEG,BEVEL,INTERNAL,END END INTERNAL BEVEL ANGLE IN DEG NONE. 1D AND 1B MODE REPLY11AC20 BYYHJ /D/ 04ANGLE IN DEG,BEVEL,INTERNAL,SMALLEST END SMALLEST END INTERNAL BEVEL ANGLE IN DEG NONE. 1D AND 1B MODE REPLY11AC20 BYYJJ /D/ 04TAPER IN DEG,BODY BODY TAPER IN DEG NONE. 1D AND 1B MODE REPLY11AC20 BYYKG /D/ 19CHARACTERISTICS,CORNER,LEFT,BODY OUTSIDE BODY OUTSIDE LEFT CORNER CHARACTERISTICS NONE. FULL TEXT WRITE-IN 0 BYYLG /D/ 19CHARACTERISTICS,CORNER,RIGHT,BODY OUTSIDE BODY OUTSIDE RIGHT CORNER CHARACTERISTICS NONE. FULL TEXT WRITE-IN 0 BYYMG /D/ 19CHARACTERISTICS,CORNER,INSIDE,LEFT FLANGE LEFT FLANGE INSIDE CORNER CHARACTERISTICS NONE. FULL TEXT WRITE-IN 0 BYYND /D/ 18TYPE,DEVICE,CONNECTING LINK ATTACHMENT CONNECTING LINK ATTACHMENT DEVICE TYPE THE TYPE OF DEVICE USED FOR FASTENING AND/OR POSITIONING THE CONNECTING LINK. SELECT REPLY CODE 10AJ74 BYYPB 10HORSEPOWER RATING,POWER SOURCE POWER SOURCE HORSEPOWER RATING THE RATED HORSEPOWER OF THE POWER SOURCE. 1B MODE REPLY 0 BYYQJ 04DIAMETER FOR WHICH DESIGNED,PIN PIN DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PIN FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BYYRD 18TYPE,PIN PIN TYPE INDICATES THE TYPE OF PIN PROVIDED. SELECT REPLY CODE 10AK54 BYYSJ T04THICKNESS RANGE,BELT,ACCOMMODATED ACCOMMODATED BELT THICKNESS RANGE THE MINIMUM AND MAXIMUM MEASUREMENT OF THE SMALLEST DIMENSION OF AN ACCOMMODATED BELT,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1F MODE REPLY11AA05 BYYTJ 04THICKNESS FOR WHICH DESIGNED,BELT BELT THICKNESS FOR WHICH DESIGNED A MEASUREMENT OF THE SMALLEST DIMENSION OF THE BELT FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BYYWJ 04LENGTH,SERIES,WIRE HOOK WIRE HOOK SERIES LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SERIES OF WIRE HOOKS,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BYYXD 18TYPE,PIN,HINGE HINGE PIN TYPE INDICATES THE TYPE OF HINGE PIN PROVIDED. SELECT REPLY CODE 10AK54 BYZDJ /D/ 04DIAMETER AND LOCATION,OUTSIDE,HUB END HUB END OUTSIDE DIAMETER AND LOCATION NONE. PLEASE USE MRC ALNC WITH ISAC TBL 0368 IN PLACE OF THIS CANCELED MRC. 3D AND 1B MODE REPLY31AA051AC203AJ91 BYZFJ /D/ 04DISTANCE FROM OUTSIDE FLANGE/RIM TO HUB END AND LOCATION DISTANCE FROM OUTSIDE FLANGE/RIM TO HUB END AND LOCATION NONE. PLEASE USE MRC ASYR WITH USE OF ISAC TBL 0368 IN PLACE OF THIS CANCELED MRC. 3D AND 1B MODE REPLY31AA051AC203AJ91 BYZGJ 04DISTANCE FROM PILOT END TO FLANGE FACE DISTANCE FROM PILOT END TO FLANGE FACE NONE. 2D AND 1B MODE REPLY21AA051AC20 BYZLJ /D/ 04DIAMETER AND LOCATION,LARGEST,FACE,FIRST STEP FIRST STEP FACE LARGEST DIAMETER AND LOCATION THE LARGEST DIAMETER AND LOCATION OF THE FIRST STEP FACE. PLEASE USE MRC ABPR WITH ISAC TBL 0368 IN PLACE OF THIS CANCELED MRC. 3D AND 1B MODE REPLY31AA051AC203AJ91 BYZMJ /D/ 04DIAMETER AND LOCATION,LARGEST,FACE,SECOND STEP SECOND STEP FACE LARGEST DIAMETER AND LOCATION THE LARGEST DIAMETER AND LOCATION OF THE SECOND STEP FACE. PLEASE USE MRC ABPT WITH ISAC TBL 0368 IN PLACE OF THIS CANCELED MRC. 3D AND 1B MODE REPLY31AA051AC203AJ91 BYZNJ /D/ 04LENGTH AND LOCATION,STEP,FIRST FIRST STEP LENGTH AND LOCATION THE LENGTH AND LOCATION OF THE FIRST STEP. PLEASE USE MRC ABPS WITH ISAC TBL 0368 IN PLACE OF THIS CANCELED MRC. 3D AND 1B MODE REPLY31AA051AC203AJ91 BYZPJ /D/ 04LENGTH AND LOCATION,STEP,SECOND SECOND STEP LENGTH AND LOCATION THE LENGTH AND LOCATION OF THE SECOND STEP. PLEASE USE MRC ABPU WITH ISAC TBL 0368 IN PLACE OF THIS CANCELED MRC. 3D AND 1B MODE REPLY31AA051AC203AJ91 BYZQJ /D/ 04DIAMETER AND LOCATION,LARGEST,FACE,THIRD STEP THIRD STEP FACE LARGEST DIAMETER AND LOCATION THE LARGEST DIAMETER AND LOCATION OF THE THIRD STEP FACE. 3D AND 1B MODE REPLY31AA051AC203AJ91 BYZRJ /D/ 04DIAMETER AND LOCATION,GROOVE,FIRST END FIRST END GROOVE DIAMETER AND LOCATION THE DIAMETER AND LOCATION OF THE FIRST END GROOVE. PLEASE USE MRC AAHH WITH ISAC TBL 0368 IN PLACE OF THIS CANCELED MRC. 3D AND 1B MODE REPLY31AA051AC203AJ91 BYZSJ /D/ 04WIDTH AND LOCATION,GROOVE,FIRST END FIRST END GROOVE WIDTH AND LOCATION THE WIDTH AND LOCATION OF THE FIRST END GROOVE. PLEASE USE MRC AAHG WITH ISAC TBL 0368 IN PLACE OF THIS CANCELED MRC. 3D AND 1B MODE REPLY31AA051AC203AJ91 BYZTJ /D/ 04LENGTH FROM GROOVE TO END AND LOCATION,END,FIRST FIRST END LENGTH FROM GROOVE TO END AND LOCATION THE LENGTH FROM THE GROVE TO THE END AND ITS LOCATION ON THE FIRST END. 3D AND 1B MODE REPLY31AA051AC203AJ91 BYZWJ /D/ 04DIAMETER AND LOCATION,LARGEST,FACE,FOURTH STEP FOURTH STEP FACE LARGEST DIAMETER AND LOCATION THE LARGEST DIAMETER AND LOCATION OF THE FOURTH STEP FACE. 3D AND 1B MODE REPLY31AA051AC203AJ91 BYZXJ 04LENGTH AND LOCATION,STEP,THIRD THIRD STEP LENGTH AND LOCATION THE LENGTH AND LOCATION OF THE THIRD STEP. 3D AND 1B MODE REPLY31AA051AC203AJ91 BYZYJ /D/ 04LENGTH AND LOCATION,STEP,FOURTH FOURTH STEP LENGTH AND LOCATION THE LENGTH AND LOCATION OF THE FOURTH STEP. 3D AND 1B MODE REPLY31AA051AC203AJ91 BYZZJ /D/ 04WIDTH AND LOCATION,GROOVE,SECOND END SECOND END GROOVE WIDTH AND LOCATION THE WIDTH AND LOCATION OF THE SECOND END GROOVE. 3D AND 1B MODE REPLY31AA051AC203AJ91 BZBBJ /D/ 04DISTANCE FROM GROOVE TO END AND LOCATION,END,SECOND SECOND END DISTANCE FROM GROOVE TO END AND LOCATION THE LENGTH FROM THE GROOVE TO THE END AND ITS LOCATION ON THE SECOND END. 3D AND 1B MODE REPLY31AA051AC203AJ91 BZBCJ /D/ 04DIAMETER AND LOCATION,GROOVE,SECOND END SECOND END GROOVE DIAMETER AND LOCATION THE DIAMETER AND LOCATION OF THE SECOND END GROOVE. 3D AND 1B MODE REPLY31AA051AC203AJ91 BZBDJ 04DISTANCE,PITCH PITCH DISTANCE THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT TEETH OR FLUTES. 2D AND 1B MODE REPLY21AA051AC20 BZBFJ 04DISTANCE BETWEEN ROLLER LINK PLATES DISTANCE BETWEEN ROLLER LINK PLATES A MEASUREMENT OF THE DISTANCE BETWEEN THE ROLLER LINK PLATES. 2D AND 1B MODE REPLY21AA051AC20 BZBGD 19CHARACTERISTIC,TRANSPARENCY TRANSPARENCY CHARACTERISTIC THE CHARACTERISTIC OF THE ITEM TO TRANSMIT LIGHT AND ALLOW VISUAL PERCEPTION. SELECT REPLY CODE 10AF93 BZBHJ /D/ 04WIDTH AT ROLLER END,PLATE,LINK LINK PLATE WIDTH AT ROLLER END NONE. 2D AND 1B MODE REPLY21AA051AC20 BZBJJ 04THICKNESS,PLATE,LINK LINK PLATE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE LINK PLATE, IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BZBKJ /D/ 04WIDTH,PLATE,OFFSET LINK OFFSET LINK PLATE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN OFFSET LINK, IN DISTINCTION FROM THICKNESS. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. 2D AND 1B MODE REPLY21AA051AC20 BZBLJ /D/ 04DISTANCE BETWEEN FLAT LINK PLATES DISTANCE BETWEEN FLAT LINK PLATES A MEASUREMENT OF THE DISTANCE BETWEEN THE FLAT LINK PLATES. 2D AND 1B MODE REPLY21AA051AC20 BZBMJ /D/ 04WIDTH AT BUSHING END,PLATE,TAPERED OFFSET LINK TAPERED OFFSET LINK PLATE WIDTH AT BUSHING END AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TAPERED OFFSET LINK PLATE AT THE BUSHING END, IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BZBNG /D/ 19CHARACTERISTICS,CORNER,INSIDE,RIGHT FLANGE RIGHT FLANGE INSIDE CORNER CHARACTERISTICS NONE. FULL TEXT WRITE-IN 0 BZBPG /D/ 19CHARACTERISTICS,CORNER,INSIDE,LEFT BORE LEFT BORE INSIDE CORNER CHARACTERISTICS NONE. FULL TEXT WRITE-IN 0 BZBQG /D/ 19CHARACTERISTICS,CORNER,INSIDE,RIGHT BORE RIGHT BORE INSIDE CORNER CHARACTERISTICS NONE. FULL TEXT WRITE-IN 0 BZBRJ 04DEPTH,COUNTERBORE,LEFT,FIRST FIRST LEFT COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZBSJ 04WIDTH,STEP,FIRST LEFT FIRST LEFT STEP WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZBTJ 04DEPTH,COUNTERBORE,LEFT,SECOND SECOND LEFT COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZBWJ 04WIDTH,STEP,SECOND LEFT SECOND LEFT STEP WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZBXJ 04DEPTH,COUNTERBORE,RIGHT,FIRST FIRST RIGHT COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZBYJ 04WIDTH,STEP,FIRST RIGHT FIRST RIGHT STEP WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZBZJ 04DEPTH,COUNTERBORE,RIGHT,SECOND SECOND RIGHT COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZCBJ 04WIDTH,STEP,SECOND RIGHT SECOND RIGHT STEP WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZCCJ 04WIDTH,KEYWAY,LEFT LEFT KEYWAY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZCDJ 04DEPTH,KEYWAY,LEFT LEFT KEYWAY DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZCFJ 04WIDTH,KEYWAY,RIGHT RIGHT KEYWAY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZCGJ 04DEPTH,KEYWAY,RIGHT RIGHT KEYWAY DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZCHJ 04DIAMETER,INSIDE,MAXIMUM,BODY BODY MAXIMUM INSIDE DIAMETER NONE. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 1D AND 1B MODE REPLY11AA05 BZCJJ 04DIAMETER,INSIDE,MINIMUM,BODY BODY MINIMUM INSIDE DIAMETER THE MINIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BZCMJ 04DIAMETER,INSIDE,MAXIMUM,FIRST LEFT COUNTERBORE FIRST LEFT COUNTERBORE MAXIMUM INSIDE DIAMETER NONE. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 1D AND 1B MODE REPLY11AA05 BZCNJ 04DIAMETER,INSIDE,MINIMUM,FIRST LEFT COUNTERBORE FIRST LEFT COUNTERBORE MINIMUM INSIDE DIAMETER NONE. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 1D AND 1B MODE REPLY11AA05 BZCPJ /D/ 04DIAMETER,OUTSIDE,MAXIMUM,FIRST LEFT STEP FIRST LEFT STEP MAXIMUM OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BZCQJ /D/ 04DIAMETER,OUTSIDE,MINIMUM,FIRST LEFT STEP FIRST LEFT STEP MINIMUM OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BZCRJ /D/ 04DIAMETER,INSIDE,MAXIMUM,SECOND LEFT COUNTERBORE SECOND LEFT COUNTERBORE MAXIMUM INSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BZCSJ /D/ 04DIAMETER,INSIDE,MINIMUM,SECOND LEFT COUNTERBORE SECOND LEFT COUNTERBORE MINIMUM INSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BZCTJ /D/ 04DIAMETER,OUTSIDE,MAXIMUM,SECOND LEFT STEP SECOND LEFT STEP MAXIMUM OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BZCWJ /D/ 04DIAMETER,OUTSIDE,MINIMUM,SECOND LEFT STEP SECOND LEFT STEP MINIMUM OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BZCXJ /D/ 04DIAMETER,INSIDE,MAXIMUM,FIRST RIGHT COUNTERBORE FIRST RIGHT COUNTERBORE MAXIMUM INSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BZCYJ /D/ 04DIAMETER,INSIDE,MINIMUM,FIRST RIGHT COUNTERBORE FIRST RIGHT COUNTERBORE MINIMUM INSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BZCZJ /D/ 04DIAMETER,OUTSIDE,MAXIMUM,FIRST RIGHT STEP FIRST RIGHT STEP MAXIMUM OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BZDBJ /D/ 04DIAMETER,OUTSIDE,MINIMUM,FIRST RIGHT STEP FIRST RIGHT STEP MINIMUM OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BZDCJ /D/ 04DIAMETER,INSIDE,MAXIMUM,SECOND RIGHT COUNTERBORE SECOND RIGHT COUNTERBORE MAXIMUM INSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BZDDJ /D/ 04DIAMETER,INSIDE,MINIMUM,SECOND RIGHT COUNTERBORE SECOND RIGHT COUNTERBORE MINIMUM INSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BZDFJ /D/ 04DIAMETER,OUTSIDE,MAXIMUM,SECOND RIGHT STEP SECOND RIGHT STEP MAXIMUM OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BZDGJ /D/ 04DIAMETER,OUTSIDE,MINIMUM,SECOND RIGHT STEP SECOND RIGHT STEP MINIMUM OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 BZDHJ 04DISTANCE FROM END TO FIRST STEP DISTANCE FROM END TO FIRST STEP NONE. 2D AND 1B MODE REPLY21AA051AC20 BZDJB 04ANGLE IN DEG,COUNTERSINK,SECOND SECOND COUNTERSINK ANGLE IN DEG NONE. 1B MODE REPLY 0 BZDKJ 04DIAMETER,COUNTERSINK,SECOND SECOND COUNTERSINK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BZDLJ 04LENGTH,COUNTERBORE COUNTERBORE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZDMJ 04LENGTH,COUNTERBORE,SECOND SECOND COUNTERBORE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZDND /D/ 01COLOR,BASIC,CUFF CUFF BASIC COLOR THE BASIC HUE OR TINT OF THE CUFF. SELECT REPLY CODE 10AD06 BZDPA /D/ 12QUANTITY,STRIPE,CUFF CUFF STRIPE QUANTITY THE NUMBER OF STRIPES INCLUDED ON THE CUFF. 1A MODE REPLY 0 BZDQJ /D/ 04WIDTH,STRIPE,CUFF CUFF STRIPE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A CUFF STRIPE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BZDRD /D/ 01COLOR,STRIPE,CUFF CUFF STRIPE COLOR THE HUE OR TINT OF THE CUFF STRIPE. SELECT REPLY CODE 10AD06 BZDSD /D/ 05DIRECTION,STRIPE,CUFF CUFF STRIPE DIRECTION THE DIRECTION OF THE STRIPE IN RELATION TO THE CUFF. SELECT REPLY CODE 10AK95 BZDTD /D/ 08LOCATION,STRIPE,CUFF CUFF STRIPE LOCATION INDICATES THE LOCATION OF THE CUFF STRIPE. SELECT REPLY CODE 10AJ91 BZDWD /D/ 01COLOR,BASIC,BODY BODY BASIC COLOR THE BASIC HUE OR TINT OF THE BODY. SELECT REPLY CODE 10AD06 BZDXA /D/ 12QUANTITY,STRIPE,BODY BODY STRIPE QUANTITY THE NUMBER OF STRIPES INCLUDED ON THE BODY. 1A MODE REPLY 0 BZDYJ /D/ 04WIDTH,STRIPE,BODY BODY STRIPE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BODY STRIPE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BZDZD /D/ 01COLOR,STRIPE,BODY BODY STRIPE COLOR THE HUE OR TINT OF THE BODY STRIPE. SELECT REPLY CODE 10AD06 BZFBD /D/ 05DIRECTION,STRIPE,BODY BODY STRIPE DIRECTION THE DIRECTION OF THE STRIPE IN RELATION TO THE BODY. SELECT REPLY CODE 10AK95 BZFCD /D/ 08LOCATION,STRIPE,BODY BODY STRIPE LOCATION INDICATES THE LOCATION OF THE BODY STRIPE. SELECT REPLY CODE 10AJ91 BZFDD /D/ 01COLOR,ANKLET ANKLET COLOR THE HUE OR TINT OF THE ANKLET(S). SELECT REPLY CODE 10AD06 BZFFD /D/ 07FEATURE,STRETCH STRETCH FEATURE AN INDICATION OF WHETHER OR NOT A STRETCH FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BZFGD /D/ 18TYPE,STITCH,BODY KNIT BODY KNIT STITCH TYPE INDICATES THE TYPE OF OPERATION FOR INTERLOCKING LOOPS OF YARN BY USE OF NEEDLES TO MAKE UP THE BODY. SELECT REPLY CODE 10AG71 BZFHD /D/ 07HEEL/TOE,REINFORCED,NYLON NYLON REINFORCED HEEL/TOE AN INDICATION OF WHETHER OR NOT A NYLON REINFORCED HEEL AND/OR TOE IS PROVIDED. SELECT REPLY CODE 10AB22 BZFJD /D/ 07FEATURE,TOP,ELASTIC KNIT-IN ELASTIC KNIT-IN TOP FEATURE AN INDICATION OF WHETHER OR NOT AN ELASTIC KNIT-IN TOP FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BZFKD /D/ 07HIGH HEEL/HEEL/SOLE/TOE AND RING TOE,STITCH,TERRY TERRY STITCH HIGH HEEL/HEEL/SOLE/TOE AND RING TOE AN INDICATION OF WHETHER OR NOT A TERRY STITCH HIGH HEEL,HEEL,SOLE,TOE,AND RING TOE IS INCLUDED. SELECT REPLY CODE 10AA49 BZFLD /D/ 07STRAP,PULL PULL STRAP AN INDICATION OF WHETHER OR NOT A PULL STRAP IS INCLUDED. SELECT REPLY CODE 10AA49 BZFMD /D/ 07STITCH INSIDE ENTIRE SOCK,KNIT,TERRY TERRY KNIT STITCH INSIDE ENTIRE SOCK AN INDICATION OF WHETHER OR NOT A TERRY KNIT STITCH INSIDE ENTIRE SOCK IS INCLUDED. SELECT REPLY CODE 10AA49 BZFND /D/ 07SOLE,CUSHION CUSHION SOLE AN INDICATION OF WHETHER OR NOT A CUSHION SOLE IS INCLUDED. SELECT REPLY CODE 10AA49 BZFPJ A03DESIGNATION,SHADE SHADE DESIGNATION A DESIGNATION USED TO IDENTIFY THE COLOR AGENT. 1D AND 1A MODE REPLY12AF94 BZFQD 19SOURCE,COLOR,PIGMENT PIGMENT COLOR SOURCE THE NAME OF THE REFERENCE SOURCE OF THE COLOR NUMBER OR NAME. SELECT REPLY CODE 10AF94 BZFRD 19GRADE,PIGMENT PIGMENT GRADE AN INDICATION OF THE QUALITY OF THE PIGMENT. SELECT REPLY CODE 10AF70 BZFSB 10PERCENTAGE,PIGMENT PIGMENT PERCENTAGE THE PROPORTION OF COLORING AGENT CONTAINED IN THE ITEM. 1B MODE REPLY 0 BZFTJ /D/ 18TYPE AND PERCENTAGE,ADDITIVE ADDITIVE TYPE AND PERCENTAGE INDICATES THE TYPE AND PERCENTAGE OF ADDITIVE. 1D AND 1B MODE REPLY15AG54 BZFWD /D/ 07FEATURE,COMPATIBILITY,METHYL ETHYL KETONE METHYL ETHYL KETONE COMPATIBILITY FEATURE AN INDICATION OF WHETHER OR NOT A COMPATIBILIY FEATURE WITH METHYL ETHYL KETONE IS PROVIDED. SELECT REPLY CODE 10AB22 BZFXJ /D/ 10AMOUNT,DYE DYE AMOUNT THE AMOUNT OF DYE. 1D AND 1B MODE REPLY12AG67 BZFYD /D/ 02DESIGN,WINDOW,HINGED HINGED WINDOW DESIGN THE DESIGN OF THE HINGED WINDOW. SELECT REPLY CODE 10AJ91 BZFZJ 04DIAMETER,OUTSIDE,PRONG PRONG OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BZGBJ 04DIAMETER,INSIDE,HEAD OPENING HEAD OPENING INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BZGCJ 04LENGTH,INSIDE,HEAD OPENING HEAD OPENING INSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZGDJ 04WIDTH,INSIDE,HEAD OPENING HEAD OPENING INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZGFL 16STYLE,DRIVE,RECESSED RECESSED DRIVE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE RECESSED DRIVE. 1L MODE REPLY 0 BZGGD /D/ 07PANEL,BLACKOUT BLACKOUT PANEL AN INDICATION OF WHETHER OR NOT A BLACKOUT PANEL IS PROVIDED. SELECT REPLY CODE 10AB22 BZGHD 18TYPE FOR WHICH DESIGNED,INSERT INSERT TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF INSERT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AB47 BZGJG 04SIZE,INSERT INSERT SIZE DESIGNATES THE SIZE BY WHICH THE INSERT IS IDENTIFIED. FULL TEXT WRITE-IN 0 BZGKA 12QUANTITY,UNIT UNIT QUANTITY THE NUMBER OF UNITS PROVIDED. 1A MODE REPLY 0 BZGLD /D/ 09MATERIAL,LOUVER LOUVER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LOUVER(S) IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BZGMD /D/ 07END,CLOSED CLOSED END AN INDICATION OF WHETHER OR NOT A CLOSED END IS INCLUDED. SELECT REPLY CODE 10AA49 BZGNJ /D/ 04WIDTH AT PIN END,PLATE,TAPERED OFFSET LINK TAPERED OFFSET LINK PLATE WIDTH AT PIN END AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TAPERED OFFSET LINK AT THE PIN END, IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BZGPJ /D/ 04DISTANCE BETWEEN ROLLER LINK PLATES AT STRAIGHT LINK END DISTANCE BETWEEN ROLLER LINK PLATES AT STRAIGHT LINK END NONE. 2D AND 1B MODE REPLY21AA051AC20 BZGQJ /D/ 04THICKNESS AT STRAIGHT LINK END,PLATE,LINK LINK PLATE THICKNESS AT STRAIGHT LINK END NONE. 2D AND 1B MODE REPLY21AA051AC20 BZGRJ /D/ 04DIAMETER,INSIDE,BUSHING BUSHING INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BZGSD 07RETRACTABILITY,POINT POINT RETRACTABILITY AN INDICATION OF WHETHER OR NOT THE POINT IS RETRACTABLE. SELECT REPLY CODE 10AB86 BZGTD /D/ 07CARTRIDGE,MULTIPLE MULTIPLE CARTRIDGE AN INDICATION OF WHETHER OR NOT A MULTIPLE CARTRIDGE IS PROVIDED. SELECT REPLY CODE 10AB22 BZGWD 07REPLACEABILITY,CARTRIDGE,INK INK CARTRIDGE REPLACEABILITY AN INDICATION OF WHETHER OR NOT THE INK CARTRIDGE IS REPLACEABLE. SELECT REPLY CODE 10AG84 BZGXD /D/ 07CARTRIDGE,INK,EXTRA EXTRA INK CARTRIDGE AN INDICATION OF WHETHER OR NOT AN EXTRA INK CARTRIDGE IS PROVIDED. SELECT REPLY CODE 10AB22 BZGYD 01COLOR,INK,CARTRIDGE CARTRIDGE INK COLOR THE HUE OR TINT OF THE CARTRIDGE INK. SELECT REPLY CODE 10AD06 BZGZA 12QUANTITY,POINT,PEN PEN POINT QUANTITY THE NUMBER OF PEN POINTS PROVIDED. 1A MODE REPLY 0 BZHBA 12QUANTITY,RESERVOIR RESERVOIR QUANTITY THE NUMBER OF RESERVOIRS PROVIDED. 1A MODE REPLY 0 BZHCA 12QUANTITY,SOCKET,BASE BASE SOCKET QUANTITY THE NUMBER OF BASE SOCKETS PROVIDED. 1A MODE REPLY 0 BZHDD /D/ 07SOCKET,BASE,HINGED HINGED BASE SOCKET AN INDICATION OF WHETHER OR NOT A HINGED BASE SOCKET(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BZHFD /D/ 07PEN,QUILL,CROW CROW QUILL PEN AN INDICATION OF WHETHER OR NOT A CROW QUILL PEN IS PROVIDED. SELECT REPLY CODE 10AB22 BZHGD 18TYPE,MEDIUM,MARKING MARKING MEDIUM TYPE INDICATES THE TYPE OF MARKING MEDIUM PROVIDED. SELECT REPLY CODE 10AJ12 BZHHD /D/ 07FEATURE,GRADE,INTENSE INTENSE GRADE FEATURE AN INDICATION OF WHETHER OR NOT AN INTENSE GRADE FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BZHJD 01COLOR,LEAD LEAD COLOR THE HUE OR TINT OF THE LEAD. SELECT REPLY CODE 10AD06 BZHKD 04SIZE,LEAD LEAD SIZE DESIGNATES THE SIZE OF THE LEAD. SELECT REPLY CODE 10AF81 BZHLD /D/ 19SURFACE FOR WHICH DESIGNED,MARKING MARKING SURFACE FOR WHICH DESIGNED AN INDICATION OF THE MARKING SURFACE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BZHMD /D/ 07CONDUCTIVITY FOR ELECTROGRAPHIC WORK,ELECTRICAL ELECTRICAL CONDUCTIVITY FOR ELECTROGRAPHIC WORK AN INDICATION OF WHETHER OR NOT AN ELECTRICAL CONDUCTIVITY FOR ELECTROGRAPHIC WORK IS PROVIDED. SELECT REPLY CODE 10AB22 BZHND /D/ 07CASING,CROSS-SECTION,OBLONG OBLONG CROSS-SECTION CASING AN INDICATION OF WHETHER OR NOT AN OBLONG CROSS-SECTION CASING IS PROVIDED. SELECT REPLY CODE 10AB22 BZHPG /D/ 18TYPE,HEAD,CLEANER CLEANER HEAD TYPE INDICATES THE TYPE OF CLEANER HEAD PROVIDED. FULL TEXT WRITE-IN 0 BZHQD 14SHAPE,CROSS-SECTIONAL,LEAD LEAD CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE LEAD WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 BZHRD /D/ 07CASING,PAPER PAPER CASING AN INDICATION OF WHETHER OR NOT A PAPER CASING IS PROVIDED. SELECT REPLY CODE 10AB22 BZHSA 12QUANTITY PER SET,COLOR,ASSORTED ASSORTED COLOR QUANTITY PER SET THE NUMBER OF ASSORTED COLOR PROVIDED IN EACH SET. 1A MODE REPLY 0 BZHTD 07SUITABILITY,WASH EFFECT WASH EFFECT SUITABILITY AN INDICATION OF WHETHER OR NOT THE ITEM IS SUITABLE FOR WASH EFFECT(S). SELECT REPLY CODE 10AM09 BZHWD 01COLOR,BARREL BARREL COLOR THE HUE OR TINT OF THE BARREL. SELECT REPLY CODE 10AD06 BZHXD 18TYPE,MECHANISM,OPERATING OPERATING MECHANISM TYPE INDICATES THE TYPE OF OPERATING MECHANISM PROVIDED. SELECT REPLY CODE 10AC82 BZHYD 04SIZE ACCOMMODATED,DIAMETER,NOMINAL,LEAD LEAD NOMINAL DIAMETER SIZE ACCOMMODATED DESIGNATES THE NOMINAL DIAMETER SIZE OF THE LEAD THE ITEM WILL ACCOMMODATE. SELECT REPLY CODE 10AF81 BZHZD /D/ 07POINT,DOUBLE DOUBLE POINT AN INDICATION OF WHETHER OR NOT A DOUBLE POINT IS PROVIDED. SELECT REPLY CODE 10AB22 BZJBD 18TYPE,LEAD LEAD TYPE INDICATES THE TYPE OF LEAD PROVIDED. SELECT REPLY CODE 10AK54 BZJCD /D/ 07FEATURE,MARKING,GLAZED SURFACE GLAZED SURFACE MARKING FEATURE AN INDICATION OF WHETHER OR NOT A GLAZED SURFACE MARKING FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BZJDD /D/ 18TYPE FOR WHICH DESIGNED,INK INK TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF INK FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BZJFA 03DESIGNATOR,VISCOSITY,GARDNER LITHOGRAPHIC SCALE GARDNER LITHOGRAPHIC SCALE VISCOSITY DESIGNATOR THE ALPHA AND/OR NUMERIC VISCOSITY DESIGNATOR OF THE GARDNER LITHOGRAPHIC SCALE. 1A MODE REPLY 0 BZJGD /D/ 07FEATURE,PREINKED PREINKED FEATURE AN INDICATION OF WHETHER OR NOT A PREINKED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BZJHD /D/ 07SPOOL SPOOL AN INDICATION OF WHETHER OR NOT A SPOOL IS PROVIDED. SELECT REPLY CODE 10AB22 BZJJD /D/ 19DEGREE,RATED,INKING INKING RATED DEGREE THE DEGREE OF INKING FOR WHICH THE ITEM IS RATED. SELECT REPLY CODE 10AF07 BZJKG 19NAME FOR WHICH DESIGNED,MANUFACTURER,MACHINE MACHINE MANUFACTURER NAME FOR WHICH DESIGNED THE NAME OF THE MANUFACTURER OF THE MACHINE FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 BZJLD 18TYPE,MACHINE MACHINE TYPE INDICATES THE TYPE OF MACHINE PROVIDED. SELECT REPLY CODE 10AK54 BZJMG /D/ 19NAME,MACHINE MACHINE NAME THE NAME OF THE MACHINE. FULL TEXT WRITE-IN 0 BZJNA 04SIZE,STOPPER STOPPER SIZE DESIGNATES THE SIZE OF THE STOPPER. 1A MODE REPLY 0 BZJPD /D/ 18TYPE,CONNECTION,TUBULATURE TUBULATURE CONNECTION TYPE INDICATES THE TYPE OF TUBULATURE CONNECTION. SELECT REPLY CODE 10AM35 BZJQA /D/ 12QUANTITY,TUBULATURE,SIDE SIDE TUBULATURE QUANTITY THE NUMBER OF SIDE TUBULATURES PROVIDED. 1A MODE REPLY 0 BZJRA /D/ 04SIZE,TAPER,STANDARD,SIDE TUBULATURE SIDE TUBULATURE STANDARD TAPER SIZE DESIGNATES THE STANDARD TAPER SIZE OF A SIDE TUBULATURE. 1A MODE REPLY 0 BZJSD /D/ 07PLATE,BOTTOM BOTTOM PLATE AN INDICATION OF WHETHER OR NOT A BOTTOM PLATE IS INCLUDED. SELECT REPLY CODE 10AA49 BZJTD /D/ 19POROSITY,DISK,FRITTED GLASS FRITTED GLASS DISK POROSITY THE POROSITY RATING OF A FRITTED GLASS DISK. SELECT REPLY CODE 10AF67 BZJWJ /D/ 04DIAMETER,PERFORATION,BOTTOM BOTTOM PERFORATION DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOTTOM PERFORATION,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY12AG67 BZJXD /D/ 07DISK,FILTER,REMOVABLE REMOVABLE FILTER DISK AN INDICATION OF WHETHER OR NOT A REMOVABLE FILTER DISK IS PROVIDED. SELECT REPLY CODE 10AB22 BZJYD /D/ 07GROOVE,INTEGRAL INTEGRAL GROOVE AN INDICATION OF WHETHER OR NOT AN INTEGRAL GROOVE/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 BZJZD /D/ 07TRAY,REMOVABLE REMOVABLE TRAY AN INDICATION OF WHETHER OR NOT A REMOVABLE TRAY IS PROVIDED. SELECT REPLY CODE 10AB22 BZKCL /D/ 16STYLE,FLASK,DISTILLING DISTILLING FLASK STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE DISTILLING FLASK. 1L MODE REPLY 0 BZKDJ /D/A04SIZE,OPENING A OPENING A SIZE NONE. 1D AND 1A MODE REPLY13AM35 BZKFJ /D/A04SIZE,OPENING B OPENING B SIZE NONE. 1D AND 1A MODE REPLY13AM35 BZKGJ /D/A04SIZE,OPENING C OPENING C SIZE NONE. 1D AND 1A MODE REPLY13AM35 BZKHJ /D/ 04ANGLE IN DEG,ATTACHMENT,SIDE ARM SIDE ARM ATTACHMENT ANGLE IN DEG THE SIDE ARM ATTACHMENT ANGLE,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 BZKJJ 04LENGTH,ARM,SIDE SIDE ARM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SIDE ARM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BZKKJ 04DISTANCE FROM TOP TO SIDE ARM CENTERLINE DISTANCE FROM TOP TO SIDE ARM CENTERLINE THE DISTANCE FROM THE TOP OF THE ITEM TO THE SIDE ARM CENTERLINE. 2D AND 1B MODE REPLY21AA051AC20 BZKLD /D/ 18TYPE,NECK NECK TYPE INDICATES THE TYPE OF NECK ON THE ITEM. SELECT REPLY CODE 10AK54 BZKMD /D/ 07SURFACE,SILVERED SILVERED SURFACE AN INDICATION OF WHETHER OR NOT A SILVERED SURFACE IS PROVIDED. SELECT REPLY CODE 10AB22 BZKND /D/ 07CONSTRUCTION,WALL,HEAVY HEAVY WALL CONSTRUCTION AN INDICATION OF WHETHER OR NOT HEAVY WALL CONSTRUCTION IS PROVIDED. SELECT REPLY CODE 10AB22 BZKPD /D/ 07FEATURE,EVACUATED EVACUATED FEATURE AN INDICATION OF WHETHER OR NOT AN EVACUATED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BZKQB /D/ 04ANGLE IN DEG,APICAL,CONE CONE APICAL ANGLE IN DEG THE APICAL ANGLE OF THE CONE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BZKRD /D/ 07CONE,RIBBED RIBBED CONE AN INDICATION OF WHETHER OR NOT RIBBING IS PROVIDED ON THE CONE. SELECT REPLY CODE 10AB22 BZKSJ /D/ 04DISTANCE FROM DISK TO LIP DISTANCE FROM DISK TO LIP THE DISTANCE FROM THE DISK TO THE LIP OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BZKTD /D/ 18TYPE,DISK,FILTER FILTER DISK TYPE INDICATES THE TYPE OF FILTER DISK PROVIDED. SELECT REPLY CODE 10AK95 BZKWD /D/ 14SHAPE,FUNNEL FUNNEL SHAPE THE PHYSICAL CONFIGURATION OF THE FUNNEL. SELECT REPLY CODE 10AD07 BZKXD 14SHAPE,BOTTOM BOTTOM SHAPE THE PHYSICAL CONFIGURATION OF THE BOTTOM OF THE ITEM. SELECT REPLY CODE 10AD07 BZKYB /D/ 04ENGLE IN DEG,TIP,STEM STEM TIP ENGLE IN DEG THE ANGLE OF THE STEM TIP,EXPRESSED IN DEGREES. 1B MODE REPLY 0 BZKZL /D/ 16STYLE,STOPCOCK STOPCOCK STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE STOPCOCK. 1L MODE REPLY 0 BZLBD /D/ 07PLUG,TAPER,STANDARD STANDARD TAPER PLUG AN INDICATION OF WHETHER OR NOT A STANDARD TAPER PLUG IS PROVIDED. SELECT REPLY CODE 10AB22 BZLCF /D/T10RATIO,TAPER,NONSTANDARD NONSTANDARD TAPER RATIO THE RATE OF DECREASE IN THICKNESS IN RELATION TO THE LENGTH OF THE TAPERED PORTION. 1F MODE REPLY 0 BZLDD /D/ 05DIRECTION,BORE,PLUG PLUG BORE DIRECTION AN INDICATION OF THE DIRECTION IN WHICH THE PLUG IS BORED. SELECT REPLY CODE 10AF63 BZLFD /D/ 07OUTLET,PLUG PLUG OUTLET AN INDICATION OF WHETHER OR NOT A PLUG OUTLET IS PROVIDED. SELECT REPLY CODE 10AB22 BZLGD /D/ 07SEAL,MERCURY MERCURY SEAL AN INDICATION OF WHETHER OR NOT A MERCURY SEAL IS PROVIDED. SELECT REPLY CODE 10AB22 BZLHJ 04DIAMETER,BALL BALL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BALL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BZLJJ /D/ 04DIAMETER,INSIDE,COVER RIM COVER RIM INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COVER RIM,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BZLKJ /D/ 10CAPACITY,CRUCIBLE CRUCIBLE CAPACITY THE CAPACITY OF THE CRUCIBLE. 2D AND 1B MODE REPLY22AG671AC20 BZLLJ 04DIAMETER ACCOMMODATED,INSIDE,TUBING TUBING INSIDE DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE TUBING,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BZLMD /D/ 07LIP,SUSPENSION SUSPENSION LIP AN INDICATION OF WHETHER OR NOT A SUSPENSION LIP IS PROVIDED. SELECT REPLY CODE 10AB22 BZLNJ 04DIAMETER,COUNTERBORE,SECOND SECOND COUNTERBORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BZLPJ 04DEPTH,DEPRESSION DEPRESSION DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZLQJ 04DISTANCE FROM CENTER TO BEGINNING OF RIDGE DISTANCE FROM CENTER TO BEGINNING OF RIDGE NONE. 2D AND 1B MODE REPLY21AA051AC20 BZLRJ 04HEIGHT,LAND LAND HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 BZLSJ /D/ 04DISTANCE FROM HOLE CENTER TO FLAT CENTER DISTANCE FROM HOLE CENTER TO FLAT CENTER THE DISTANCE FROM THE CENTER OF THE HOLE TO THE CENTER OF THE FLAT. 2D AND 1B MODE REPLY21AA051AC20 BZLTJ /D/ 04DISTANCE FROM HOLE CENTER TO FLAT CENTER,OUTSIDE OUTSIDE DISTANCE FROM HOLE CENTER TO FLAT CENTER THE OUTSIDE DISTANCE FROM THE CENTER OF THE HOLE TO THE CENTER OF THE FLAT. 2D AND 1B MODE REPLY21AA051AC20 BZLWJ 04THICKNESS,OUTSIDE OUTSIDE THICKNESS AN OUTSIDE MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 2D AND 1B MODE REPLY21AA051AC20 BZLXD 14SHAPE,CORNER CORNER SHAPE THE PHYSICAL CONFIGURATION OF THE CORNER. SELECT REPLY CODE 10AE88 BZLYD /D/ 08LOCATION,KEYWAY KEYWAY LOCATION INDICATES THE LOCATION OF THE KEYWAY ON THE ITEM. SELECT REPLY CODE 10AJ91 BZMBA /D/ 12QUANTITY,OPENING,HOLE HOLE OPENING QUANTITY THE NUMBER OF HOLE OPENINGS PROVIDED. 1A MODE REPLY 0 BZMCA /D/ 12QUANTITY,OPENING,SLOT SLOT OPENING QUANTITY THE NUMBER OF SLOT OPENINGS PROVIDED. 1A MODE REPLY 0 BZMDD /D/ 07FILLING,GRAPHITE GRAPHITE FILLING AN INDICATION OF WHETHER OR NOT A GRAPHITE FILLING IS INCLUDED. SELECT REPLY CODE 10AA49 BZMFD /D/ 07IMPREGNATION,LUBRICANT LUBRICANT IMPREGNATION AN INDICATION OF WHETHER OR NOT LUBRICANT IMPREGNATION IS INCLUDED. SELECT REPLY CODE 10AA49 BZMGG /D/ 19SPEC/STD,LUBRICANT LUBRICANT SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE LUBRICANT. FULL TEXT WRITE-IN 0 BZMHJ 04RADIUS,TOP,SPHERICAL SEAT SPHERICAL SEAT TOP RADIUS THE RADIUS OF THE SPHERICAL SEAT TOP. 2D AND 1B MODE REPLY21AA051AC20 BZMJJ /D/ 04DEPTH,CHAMFER,CORNER CORNER CHAMFER DEPTH NONE. REPLACED BY MRC AGHG WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 BZMKB /D/ 04ANGLE IN DEG,CHAMFER,CORNER CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 BZMLJ /D/ 04DEPTH,CORNER CORNER DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZMMD /D/ 07TOOL,SETTING,INSTALLATION INSTALLATION SETTING TOOL AN INDICATION OF WHETHER OR NOT A SETTING TOOL IS REQUIRED FOR INSTALLATION. SELECT REPLY CODE 10AE40 BZMND /D/ 07THREAD,LEFT-HAND LEFT-HAND THREAD AN INDICATION OF WHETHER OR NOT A LEFT-HAND THREAD IS PROVIDED. SELECT REPLY CODE 10AB22 BZMPJ 13THREAD SIZE FOR WHICH DESIGNED,NOMINAL,CONNECTOR CONNECTOR NOMINAL THREAD SIZE FOR WHICH DESIGNED THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL THREAD SIZE OF THE CONNECTOR FOR WHICH DESIGNED. 1D AND 1B MODE REPLY11AA05 BZMQJ 04LENGTH,DIAMETER,INSIDE INSIDE DIAMETER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE INSIDE DIAMETER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BZMRD /D/ 07SEAT,BEVELED BEVELED SEAT AN INDICATION OF WHETHER OR NOT A BEVELED SEAT IS INCLUDED. SELECT REPLY CODE 10AA49 BZMSD /D/ 07GASKET,ATTACHED ATTACHED GASKET AN INDICATION OF WHETHER OR NOT AN ATTACHED GASKET IS INCLUDED. SELECT REPLY CODE 10AA49 BZMTD /D/ 07SHOULDER SHOULDER AN INDICATION OF WHETHER OR NOT A SHOULDER IS INCLUDED. SELECT REPLY CODE 10AA49 BZMWJ /D/ 04TAPER IN DEG,BORE BORE TAPER IN DEG NONE. 1D AND 1B MODE REPLY11AC20 BZMXD 19CONDITION,SURFACE,OUTSIDE,ROUND CAP ROUND CAP OUTSIDE SURFACE CONDITION AN INDICATION OF THE CONDITION OF THE OUTSIDE SURFACE OF A ROUND CAP. SELECT REPLY CODE 10AA41 BZMYJ 04DIAMETER,OVERALL,CLOSED END CLOSED END OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF THE CLOSED END. 2D AND 1B MODE REPLY21AA051AC20 BZMZJ /D/ 04WIDTH,LOUVER LOUVER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE LOUVER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BZNBJ 04LENGTH UNDER SHOULDER LENGTH UNDER SHOULDER A MEASUREMENT OF THE LONGEST DIMENSION OF THAT PORTION OF THE ITEM UNDER THE SHOULDER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BZNCD 18TYPE,MEDIUM,REFINEMENT REFINEMENT MEDIUM TYPE INDICATES THE TYPE OF REFINEMENT MEDIUM. SELECT REPLY CODE 10AH21 BZNDD 18TYPE,DEVICE,REFINEMENT REFINEMENT DEVICE TYPE INDICATES THE TYPE OF REFINEMENT DEVICE PROVIDED. SELECT REPLY CODE 10AC58 BZNFA 12QUANTITY,HOLE,VENT VENT HOLE QUANTITY THE NUMBER OF VENT HOLES PROVIDED ON THE ITEM. 1A MODE REPLY 0 BZNGD 14SHAPE,HOLE,VENT VENT HOLE SHAPE THE PHYSICAL CONFIGURATION OF THE VENT HOLE. SELECT REPLY CODE 10AD07 BZNHJ 04LENGTH,HOLE,SQUARE VENT SQUARE VENT HOLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SQUARE VENT HOLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BZNJA 19NUMBER,TAPER,END CONNECTION END CONNECTION TAPER NUMBER AN INDICATION OF THE NUMBER OF THE END CONNECTION TAPER. 1A MODE REPLY 0 BZNKD 19FINISH,SURFACE,MACHINED MACHINED SURFACE FINISH AN INDICATION OF THE TYPE OF MACHINED SURFACE FINISH ON THE ITEM. SELECT REPLY CODE 10AA41 BZNLD /D/ 07PROVISION,WIRE/CORD WIRE/CORD PROVISION AN INDICATION OF WHETHER OR NOT A PROVISION FOR A WIRE AND/OR CORD IS INCLUDED. SELECT REPLY CODE 10AA49 BZNMJ 04DIAMETER FOR WHICH DESIGNED,WIRE/CORD WIRE/CORD DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WIRE OR CORD FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BZNNA 12QUANTITY,PRONG PRONG QUANTITY THE NUMBER OF PRONGS PROVIDED. 1A MODE REPLY 0 BZNPD /D/ 07FEATURE,REINFORCEMENT,BLADE BLADE REINFORCEMENT FEATURE AN INDICATION OF WHETHER OR NOT A BLADE REINFORCEMENT FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BZNQD 18TYPE,EDGE,BLADE BLADE EDGE TYPE INDICATES THE TYPE OF BLADE EDGE PROVIDED. SELECT REPLY CODE 10AL25 BZNRJ /D/ 04DIAMETER,CUT CUT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CUT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BZNSD /D/ 08LOCATION,EDGE,NONCUTTING NONCUTTING EDGE LOCATION INDICATES THE LOCATION OF THE NONCUTTING EDGE. SELECT REPLY CODE 10AJ91 BZNTJ /D/A12QUANTITY PER UNIT OF MEASURE,TWIST TWIST QUANTITY PER UNIT OF MEASURE THE NUMBER OF COMPLETE TWISTS PER UNIT OF MEASURE. 1D AND 1A MODE REPLY11AB39 BZNWJ 04LENGTH,SECTION,TOOTH TOOTH SECTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TOOTH SECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BZNXJ 10EXPANSION,MAXIMUM MAXIMUM EXPANSION THE MAXIMUM DISTANCE THE ITEM CAN BE EXPANDED. 1D AND 1B MODE REPLY11AA05 BZNYD 11METHOD,GRASPING,BLADE BLADE GRASPING METHOD THE MEANS USED TO GRASP OR HOLD THE BLADE(S). SELECT REPLY CODE 10AE44 BZNZD 19CONDITION,SURFACE,BLADE OUTSIDE BLADE OUTSIDE SURFACE CONDITION THE CONDITION OF THE BLADE WITH RESPECT TO THE OUTSIDE SURFACE TEXTURE. SELECT REPLY CODE 10AK39 BZPBD /D/ 07GAGE,ADJUSTMENT ADJUSTMENT GAGE AN INDICATION OF WHETHER OR NOT AN ADJUSTMENT GAGE IS PROVIDED. SELECT REPLY CODE 10AB22 BZPCJ /D/ 04DIAMETER,MAXIMUM,SHAFT SHAFT MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHAFT,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BZPDJ /D/ 04WIDTH,MAXIMUM,SHAFT SHAFT MAXIMUM WIDTH A MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SHAFT,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 BZPFD 11METHOD,RETENTION,EXPANSION EXPANSION RETENTION METHOD THE MEANS USED TO RETAIN THE ITEM IN ITS EXPANDED FORM. SELECT REPLY CODE 10AE36 BZPGD /D/ 07LID,BASKET,HINGED HINGED BASKET LID AN INDICATION OF WHETHER OR NOT A HINGED BASKET LID IS PROVIDED. SELECT REPLY CODE 10AB22 BZPHD 02DESIGN,GUARD GUARD DESIGN THE DESIGN OF THE GUARD. SELECT REPLY CODE 10AK54 BZPJJ 04DIAMETER,END,DISTAL DISTAL END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DISTAL END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BZPKJ 04WIDTH,END,DISTAL DISTAL END WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE DISTAL END,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BZPLD /D/ 07FEATURE,IRRIGATION IRRIGATION FEATURE AN INDICATION OF WHETHER OR NOT AN IRRIGATION FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BZPMD /D/ 07FEATURE,SELF-RETAINING SELF-RETAINING FEATURE AN INDICATION OF WHETHER OR NOT A SELF-RETAINING FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 BZPND /D/ 07SEPARATOR,FLASK FLASK SEPARATOR AN INDICATION OF WHETHER OR NOT A FLASK SEPARATOR IS PROVIDED. SELECT REPLY CODE 10AB22 BZPPD /D/ 07FEATURE,WEIGHTED WEIGHTED FEATURE AN INDICATION OF WHETHER OR NOT A WEIGHTED FEATURE/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 BZPQD /D/ 07TRACTOR,AXIS AXIS TRACTOR AN INDICATION OF WHETHER OR NOT AN AXIS TRACTOR(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BZPRD /D/ 07TUBE,SUCTION SUCTION TUBE AN INDICATION OF WHETHER OR NOT A SUCTION TUBE(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BZPSD 08LOCATION,SCALE SCALE LOCATION INDICATES THE LOCATION OF THE SCALE ON THE ITEM. SELECT REPLY CODE 10AJ91 BZPTD 18TYPE,GLASS,BARREL BARREL GLASS TYPE INDICATES THE TYPE OF BARREL GLASS PROVIDED. SELECT REPLY CODE 10AM13 BZPWD /D/ 07TIP,DISPOSABLE DISPOSABLE TIP AN INDICATION OF WHETHER OR NOT A DISPOSABLE TIP IS PROVIDED. SELECT REPLY CODE 10AB22 BZPXA 12QUANTITY,RING,FINGER FINGER RING QUANTITY THE NUMBER OF FINGER RINGS PROVIDED. 1A MODE REPLY 0 BZPYD 18TYPE,GLASS,PLUNGER PLUNGER GLASS TYPE INDICATES THE TYPE OF PLUNGER GLASS PROVIDED. SELECT REPLY CODE 10AM13 BZPZD 19MARKING,PLUNGER PLUNGER MARKING AN INDICATION OF THE MARKING(S) ON THE PLUNGER. SELECT REPLY CODE 10AB44 BZQBD 02DESIGN,TIP,BARREL BARREL TIP DESIGN THE DESIGN OF THE BARREL TIP. SELECT REPLY CODE 10AK54 BZQCD /D/ 18TYPE,REST,THUMB,PLUNGER PLUNGER THUMB REST TYPE INDICATES THE TYPE OF THUMB REST PROVIDED ON THE PLUNGER. SELECT REPLY CODE 10AK54 BZQDD /D/ 07THREADS TO ACCOMMODATE HANDLE,END,PLUNGED PLUNGER END THREADS TO ACCOMMODATE HANDLE AN INDICATION OF WHETHER OR NOT THREADS ON THE PLUNGER END ARE PROVIDED TO ACCOMMODATE A HANDLE. SELECT REPLY CODE 10AB22 BZQFD /D/ 09MATERIAL,CANNULA CANNULA MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CANNULA IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BZQGD 14SHAPE,CANNULA CANNULA SHAPE THE PHYSICAL CONFIGURATION OF THE CANNULA. SELECT REPLY CODE 10AD07 BZQHJ /D/ 04LENGTH,OVERALL,NEEDLE NEEDLE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE NEEDLE. 2D AND 1B MODE REPLY21AA051AC20 BZQJD /D/ 07HUB,NEEDLE NEEDLE HUB AN INDICATION OF WHETHER OR NOT A NEEDLE HUB IS PROVIDED. SELECT REPLY CODE 10AB22 BZQKJ 04LENGTH,HUB HUB LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE HUB,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 BZQLJ 04LENGTH,OVERALL,BARREL BARREL OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BARREL. 1D AND 1B MODE REPLY11AA05 BZQMJ 04DIAMETER,OUTSIDE,BARREL BARREL OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BARREL,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BZQNG /D/ 19NAME FOR WHICH DESIGNED,TRADE,MACHINE MACHINE TRADE NAME FOR WHICH DESIGNED THE TRADE NAME OF THE MACHINE FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 BZQPG /D/ 19MODEL ON WHICH USED,MACHINE MACHINE MODEL ON WHICH USED THE MODEL OF MACHINE ON WHICH THE ITEM IS USED. FULL TEXT WRITE-IN 0 BZQQJ 10STRENGTH,BREAKING BREAKING STRENGTH THE MEASURED LOAD REQUIRED TO BREAK THE ITEM IN TENSION. 2D AND 1B MODE REPLY21AB181AC20 BZQRJ /D/ 04DIAMETER,SHAFT,FIRST FIRST SHAFT DIAMETER NONE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. 2D AND 1B MODE REPLY21AA051AC20 BZQSJ /D/ 04DIAMETER,SHAFT,SECOND SECOND SHAFT DIAMETER NONE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. 2D AND 1B MODE REPLY21AA051AC20 BZQTJ /D/ 04LENGTH,SHAFT,FIRST FIRST SHAFT LENGTH NONE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 2D AND 1B MODE REPLY21AA051AC20 BZQWJ /D/ 04LENGTH,SHAFT,SECOND SECOND SHAFT LENGTH NONE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. 2D AND 1B MODE REPLY21AA051AC20 BZQXJ /D/ 04DIAMETER,OUTSIDE,FIRST HUB FIRST HUB OUTSIDE DIAMETER NONE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/16/2024 2D AND 1B MODE REPLY21AA051AC20 BZQYJ /D/ 04DIAMETER,OUTSIDE,SECOND HUB SECOND HUB OUTSIDE DIAMETER NONE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 2D AND 1B MODE REPLY21AA051AC20 BZQZJ /D/ 04LENGTH,HUB,FIRST FIRST HUB LENGTH NONE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 2D AND 1B MODE REPLY21AA051AC20 BZRBJ /D/ 04LENGTH,HUB,SECOND SECOND HUB LENGTH NONE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. 2D AND 1B MODE REPLY21AA051AC20 BZRCA 12QUANTITY,STRAND STRAND QUANTITY THE NUMBER OF STRANDS PROVIDED. 1A MODE REPLY 0 BZRDJ 04DIAMETER,PITCH,V GROOVE V GROOVE PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF THE V GROOVE. 2D AND 1B MODE REPLY21AA051AC20 BZRFA /D/ 12QUANTITY PER LENGTH,SECTION,PIPE PIPE SECTION QUANTITY PER LENGTH THE NUMBER OF INDIVIDUAL PIPE SECTIONS PER LENGTH. 1A MODE REPLY 0 BZRGD 11METHOD,FASTENING,LONGITUDINAL JOINT LONGITUDINAL JOINT FASTENING METHOD THE MEANS USED FOR FASTENING THE LONGITUDINAL JOINT. SELECT REPLY CODE 10AM39 BZRHD /D/ 18TYPE,FASTENER,JOINT JOINT FASTENER TYPE INDICATES THE TYPE OF JOINT FASTENER(S) PROVIDED. SELECT REPLY CODE 10AC52 BZRJG 19AGENCY,APPROVING,INGESTED LIQUID USE INGESTED LIQUID USE APPROVING AGENCY THE NAME OF THE AGENCY APPROVING THE USE OF INGESTED LIQUIDS/S/. FULL TEXT WRITE-IN 0 BZRKG 19AGENCY,APPROVING,POTABLE WATER USE POTABLE WATER USE APPROVING AGENCY THE NAME OF THE AGENCY APPROVING THE USE OF POTABLE WATER. FULL TEXT WRITE-IN 0 BZRLJ /D/ 04DIAMETER,OUTSIDE,BEAD BEAD OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BZRMJ 04LENGTH,FLARE FLARE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZRNJ /D/ 04LENGTH FROM GROOVE/BEAD TO END LENGTH FROM GROOVE/BEAD TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 BZRPJ /D/ 04WIDTH,BEAD BEAD WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZRQJ /D/ 04LENGTH,BEAD CENTER TO END BEAD CENTER TO END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZRRD 13THREAD SERIES THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS. SELECT REPLY CODE 10AH06 BZRSG /D/ 19SPEC/STD,CONNECTION,END END CONNECTION SPEC/STD THE SPECIFICATION AND/OR STANDARD OF THE END CONNECTION. FULL TEXT WRITE-IN 0 BZRTG /D/ 19SPEC/STD,MATERIAL,COVER COVER MATERIAL SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE COVER MATERIAL. FULL TEXT WRITE-IN 0 BZRWJ /D/ 04LENGTH,END,PLAIN PLAIN END LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS, FROM THE END TO THE TERMOF THE SMOOTH SURFACE. 2D AND 1B MODE REPLY21AA051AC20 BZRXD /D/ 07END,ENLARGED ENLARGED END AN INDICATION OF WHETHER OR NOT AN ENLARGED END(S) IS PROVIDED. SELECT REPLY CODE 10AB22 BZRYJ /D/ 08LOCATION AND LENGTH,PORTION,ENLARGED ENLARGED PORTION LOCATION AND LENGTH INDICATES THE LOCATION OF THE ENLARGED PORTION AND ITS LENGTH. 3D AND 1B MODE REPLY31AA051AC203AJ91 BZRZJ /D/ 08LOCATION AND INSIDE DIAMETER,END,ENLARGED ENLARGED END LOCATION AND INSIDE DIAMETER INDICATES THE LOCATION OF THE ENLARGED END AND ITS INSIDE DIAMETER. 3D AND 1B MODE REPLY31AA051AC203AJ91 BZSBG /D/ 19COMPOSITION IN PERCENT,CHEMICAL CHEMICAL COMPOSITION IN PERCENT THE CHEMICAL/S/ AND THE ALLOWABLE PERCENTAGE OF EACH USED TO COMPOUND THE BASIC MATERIAL OF THE ITEM. FULL TEXT WRITE-IN 0 BZSCD /D/ 11METHOD,PROCESS PROCESS METHOD THE MEANS USED FOR PROCESSING THE ITEM. SELECT REPLY CODE 10AC58 BZSDD /D/ 07SEAM,SPIRAL SPIRAL SEAM AN INDICATION OF WHETHER OR NOT A SPIRAL SEAM IS PROVIDED. SELECT REPLY CODE 10AB22 BZSFL /D/ 16STYLE,BEND,PIPE/TUBE PIPE/TUBE BEND STYLE THE STYLE DESIGNATION INDICATING THE CONFIRGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PIPE AND/OR TUBE BEND/S/. 1L MODE REPLY 0 BZSGJ /D/ 19LEGEND P1 LEGEND P1 NONE. 2D AND 1B MODE REPLY21AA051AC20 BZSHJ /D/ 19LEGEND R1 LEGEND R1 NONE. 2D AND 1B MODE REPLY21AA051AC20 BZSJJ /D/ 19LEGEND R2 LEGEND R2 NONE. 2D AND 1B MODE REPLY21AA051AC20 BZSKJ /D/ 19LEGEND T1 LEGEND T1 NONE. 2D AND 1B MODE REPLY21AA051AC20 BZSLD /D/ 19PROJECTILE FOR WHICH DESIGNED PROJECTILE FOR WHICH DESIGNED AN INDICATION OF THE PROJECTILE(S) FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 BZSMD /D/ 18TYPE,CONTROL,PROJECTILE RELEASE PROJECTILE RELEASE CONTROL TYPE INDICATES THE TYPE OF PROJECTILE RELEASE CONTROL PROVIDED. SELECT REPLY CODE 10AL37 BZSNA /D/ 12QUANTITY,JAR JAR QUANTITY THE NUMBER OF JARS PROVIDED. 1A MODE REPLY 0 BZSPD /D/ 09MATERIAL,ARM,FLOAT FLOAT ARM MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FLOAT ARM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BZSQJ A18TYPE AND QUANTITY,CONNECTION,INLET INLET CONNECTION TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF INLET CONNECTIONS PROVIDED. 1D AND 1A MODE REPLY12AB76 BZSRA 13THREAD QUANTITY PER INCH,INLET INLET THREAD QUANTITY PER INCH A MEASUREMENT OF THE NUMBER OF THREADS ON THE INLET PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 BZSSJ A18TYPE AND QUANTITY,CONNECTION,OUTLET OUTLET CONNECTION TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF OUTLET CONNECTIONS PROVIDED. 1D AND 1A MODE REPLY12AB76 BZSTJ /D/ 04DIAMETER,OUTSIDE,OUTLET FLANGE OUTLET FLANGE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTLET FLANGE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BZSWA 13THREAD QUANTITY PER INCH,OUTLET OUTLET THREAD QUANTITY PER INCH A MEASUREMENT OF THE NUMBER OF THREADS ON THE OUTLET PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 BZSXJ 10CAPACITY AT MAXIMUM WORKING PRESSURE,RATED RATED CAPACITY AT MAXIMUM WORKING PRESSURE THE RATED CAPACITY OF THE ITEM AT MAXIMUM WORKING PRESSURE. 1D AND 1B MODE REPLY12AG67 BZSYJ 10AREA ON WHICH CAPACITY IS BASED,SURFACE,RADIATING RADIATING SURFACE AREA ON WHICH CAPACITY IS BASED A MEASUREMENT OF THE AREA OF THE RADIATING SURFACE ON WHICH THE CAPACITY OF THE ITEM IS BASED. 1D AND 1B MODE REPLY12AG67 BZSZJ 10CAPACITY PER HOUR,WATER WATER CAPACITY PER HOUR THE CAPACITY OF WATER PER HOUR OF THE ITEM. 1D AND 1B MODE REPLY12AG67 BZTBD /D/ 19SIMILARITY,CONNECTION,INLET/OUTLET INLET/OUTLET CONNECTION SIMILARITY AN INDICATION OF WHETHER OR NOT THE INLET AND/OR OUTLET CONNECTION(S) IS IDENTICAL. SELECT REPLY CODE 10AB78 BZTCJ /D/ 04SIZE,PIPE,NOMINAL,INLET/OUTLET CONNECTION INLET/OUTLET CONNECTION NOMINAL PIPE SIZE THE VALUE USED TO DEFINE THE NOMINAL DIAMETER OF THE INLET AND/OR OUTLET CONNECTION PIPE. 1D AND 1B MODE REPLY11AA05 BZTDD /D/ 18TYPE,CONNECTION,INLET/OUTLET INLET/OUTLET CONNECTION TYPE INDICATES THE TYPE OF INLET AND/OR OUTLET CONNECTION PROVIDED. PLEASE USE MRC ACQW FOR INLET CONNECTION TYPE AND MRC ARTH FOR OUTLET CONNECTION TYPE IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AB76 BZTFD 18TYPE,FACING,FLANGE FLANGE FACING TYPE INDICATES THE TYPE OF FLANGE FACING PROVIDED. SELECT REPLY CODE 10AG89 BZTGJ 04DIAMETER,CIRCLE,BOLT,FLANGE FLANGE BOLT CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FLANGE BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BZTHD /D/ 07PROVISION,THREAD,INLET/OUTLET CONNECTION INLET/OUTLET CONNECTION THREAD PROVISION AN INDICATION OF WHETHER OR NOT THE INLET AND/OR OUTLET CONNECTION IS THREADED. SELECT REPLY CODE 10AE00 BZTJD /D/ 08LOCATION IN RELATION TO INSTALLED POSITION,INLET INLET LOCATION IN RELATION TO INSTALLED POSITION INDICATES THE LOCATION OF THE INLET IN RELATION TO THE INSTALLED POSITION OF THE ITEM. SELECT REPLY CODE 10AJ91 BZTKD /D/ 08LOCATION IN RELATION TO INSTALLED POSITION,OUTLET OUTLET LOCATION IN RELATION TO INSTALLED POSITION INDICATES THE LOCATION OF THE OUTLET IN RELATION TO THE INSTALLED POSITION OF THE ITEM. SELECT REPLY CODE 10AJ91 BZTLD /D/ 07GLASS,GAGE GAGE GLASS AN INDICATION OF WHETHER OR NOT A GAGE GLASS IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 BZTMJ /D/A18TYPE AND QUANTITY,STRAINER STRAINER TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF STRAINERS PROVIDED. 1D AND 1A MODE REPLY13AK54 BZTNJ 04DIAMETER,INSIDE,LOOP LOOP INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LOOP,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BZTPJ 04DISTANCE FROM OUTER EDGE OF LUG TO HOLE CENTER DISTANCE FROM OUTER EDGE OF LUG TO HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 BZTQJ 04DIAMETER,HOLE,LUG LUG HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BZTRJ 04DISTANCE FROM LOOP CENTER TO BASE OF OFFSET TONGUE DISTANCE FROM LOOP CENTER TO BASE OF OFFSET TONGUE NONE. 2D AND 1B MODE REPLY21AA051AC20 BZTSJ 04LENGTH BETWEEN FASTENERS LENGTH BETWEEN FASTENERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BZTTD /D/ 07HOLE,TONGUE TONGUE HOLE AN INDICATION OF WHETHER OR NOT A HOLE/S/ ON THE TONGUE IS INCLUDED. SELECT REPLY CODE 10AA49 BZTWD /D/ 09MATERIAL,FASTENER FASTENER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FASTENER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 BZTXD /D/ 07LOCKWASHER LOCKWASHER AN INDICATION OF WHETHER OR NOT A LOCKWASHER IS PROVIDED. SELECT REPLY CODE 10AB22 BZTYJ /D/ 04DIAMETER,CLAMP,CLOSED CLOSED CLAMP DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CLAMP WHEN IN A CLOSED POSITION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BZTZJ /D/ 04DIAMETER,CLAMP,OPEN OPEN CLAMP DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CLAMP WHEN IN AN OPEN POSITION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BZWBG /D/ 11METHOD,ACTUATING,ADJUSTING MECHANISM ADJUSTING MECHANISM ACTUATING METHOD THE MEANS OF ACTUATING THE ADJUSTING MECHANISM. FULL TEXT WRITE-IN 0 BZWCG /D/ 11METHOD,MOUNTING,CLAMP TO INSTRUMENT PANEL CLAMP TO INSTRUMENT PANEL MOUNTING METHOD THE MEANS USED TO MOUNT THE CLAMP TO THE INSTRUMENT PANEL. FULL TEXT WRITE-IN 0 BZWDD /D/ 13THREAD FEATURE,SELF-LOCKING SELF-LOCKING THREAD FEATURE AN INDICATION OF WHETHER OR NOT A SELF-LOCKING THREAD FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BZWFD /D/ 07DEVICE,FASTENING FASTENING DEVICE AN INDICATION OF WHETHER OR NOT A FASTENING DEVICE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BZWGJ 04THICKNESS FOR WHICH DESIGNED,PANEL PANEL THICKNESS FOR WHICH DESIGNED A MEASUREMENT OF THE SMALLEST DIMENSION OF THE PANEL FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BZWHD /D/ 07RIVET RIVET AN INDICATION OF WHETHER OR NOT A RIVET(S) IS INCLUDED. SELECT REPLY CODE 10AA49 BZWJJ 10SIZE ACCOMMODATED,I-BEAM I-BEAM SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE I-BEAM THE ITEM WILL ACCOMMODATE. 2D AND 1B MODE REPLY21AA051AC20 BZWKJ /D/ 04DISTANCE BETWEEN SUSPENDED CLAMP HALVES DISTANCE BETWEEN SUSPENDED CLAMP HALVES THE DISTANCE BETWEEN THE CLAMP HALVES WHEN SUSPENDED. 2D AND 1B MODE REPLY21AA051AC20 BZWLJ /D/ 04DIAMETER,COUNTERSINK,FIRST FIRST COUNTERSINK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BZWMD 11METHOD,DELAY,SIGNAL SIGNAL DELAY METHOD THE MEANS BY WHICH THE SIGNAL IS DELAYED. SELECT REPLY CODE 10AK95 BZWND /D/ 07FINGER,TRIGGER TRIGGER FINGER AN INDICATION OF WHETHER OR NOT A TRIGGER FINGER IS INCLUDED. SELECT REPLY CODE 10AA49 BZWPD /D/ 07CODED,COLOR,SIZE SIZE COLOR CODED AN INDICATION OF WHETHER OR NOT COLOR CODING FOR SIZE IS INCLUDED. SELECT REPLY CODE 10AA49 BZWQD /D/ 07FEATURE,PREPOWDERED PREPOWDERED FEATURE AN INDICATION OF WHETHER OR NOT A PREPOWDERED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BZWRD /D/ 07INDICATOR,STERILIZATION STERILIZATION INDICATOR AN INDICATION OF WHETHER OR NOT A STERILIZATION INDICATOR IS INCLUDED. SELECT REPLY CODE 10AA49 BZWSH /D/ 11METHOD AND LOCATION,CLOSURE,CAPE CAPE CLOSURE METHOD AND LOCATION THE MEANS BY WHICH THE CAPE IS CLOSED AND THE LOCATION TO WHICH THE CLOSURE METHOD IS APPLICABLE. 2D MODE REPLY 23AM393AJ91 BZWTH /D/ 11METHOD AND LOCATION,CLOSURE,BIB BIB CLOSURE METHOD AND LOCATION THE MEANS BY WHICH THE BIB IS CLOSED AND THE LOCATION TO WHICH THE CLOSURE METHOD IS APPLICABLE. 2D MODE REPLY 23AM393AJ91 BZWWH /D/ 11METHOD AND LOCATION,FASTENING FASTENING METHOD AND LOCATION THE MEANS BY WHICH THE ITEM IS FASTENED AND THE LOCATION TO WHICH THE FASTENING METHOD IS APPLICABLE. 2D MODE REPLY 23AM393AJ91 BZWXJ 04LENGTH,ARM,LIFT LIFT ARM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE LIFT ARM,IN DISTINCION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BZWYD 11METHOD,FASTENING,HANDLE HANDLE FASTENING METHOD THE MEANS BY WHICH THE HANDLE IS FASTENED TO THE ITEM. SELECT REPLY CODE 10AB47 BZWZD /D/ 07DEVICE,CONNECTING CONNECTING DEVICE AN INDICATION OF WHETHER A CONNECTING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 BZXBJ /D/A19NUMBER,IDENTIFYING,CONNECTOR CONNECTOR IDENTIFYING NUMBER THE NUMBER ASSIGNED TO THE CONNECTOR FOR THE PURPOSE OF READY IDENTIFICATION. 1D AND 1A MODE REPLY12AG99 BZXCJ /D/ 04DISTANCE BETWEEN HOLES/STUD CENTERS,VERTICAL VERTICAL DISTANCE BETWEEN HOLE/STUD CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 BZXDH /D/ 09MATERIAL AND LOCATION,FASTENER FASTENER MATERIAL AND LOCATION THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FASTENER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT,AND ITS LOCATION. 2D MODE REPLY 26AD093AJ91 BZXFD /D/ 08LOCATION,ADJUSTMENT,WAIST WAIST ADJUSTMENT LOCATION INDICATES THE LOCATION OF THE WAIST ADJUSTMENT ON THE ITEM. SELECT REPLY CODE 10AJ91 BZXGD /D/ 07IMPREGNATION,PROTECTIVE,VESICANT GAS VESICANT GAS PROTECTIVE IMPREGNATION AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A PROTECTIVE IMPREGNATION AGAINST VESICANT GAS. SELECT REPLY CODE 10AB22 BZXHD /D/ 07CROTCH,FASTENER,SNAP SNAP FASTENER CROTCH AN INDICATION OF WHETHER OR NOT A SNAP FASTENER CROTCH IS INCLUDED. SELECT REPLY CODE 10AA49 BZXJD /D/ 07KNEES,REINFORCED REINFORCED KNEES AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH REINFORCED KNEES. SELECT REPLY CODE 10AB22 BZXKD /D/ 07SEAMS,SEALED,ELECTRONICALLY ELECTRONICALLY SEALED SEAMS AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH ELECTRONICALLY SEALED SEAMS. SELECT REPLY CODE 10AB22 BZXLD /D/ 04SIZE,WAIST WAIST SIZE DESIGNATES THE WAIST SIZE AS DETERMINED BY THE MANUFACTURER. SELECT REPLY CODE 10AF81 BZXMD 11METHOD,FASTENING FASTENING METHOD THE MEANS BY WHICH THE ITEM IS FASTENED. SELECT REPLY CODE 10AF69 BZXND /D/ 11METHOD,ATTACHMENT,SHOULDER STRAP SHOULDER STRAP ATTACHMENT METHOD THE MEANS BY WHICH THE SHOULDER STRAP IS ATTACHED TO THE ITEM. SELECT REPLY CODE 10AF69 BZXPA /D/ 12QUANTITY,LINER LINER QUANTITY THE NUMBER OF LINERS PROVIDED. 1A MODE REPLY 0 BZXQJ /D/ 10WEIGHT,MATERIAL,LINER LINER MATERIAL WEIGHT A DESIGNATION EXPRESSED IN UNITS OF WEIGHT PER SQUARE OR LINEAR YARD OF A SPECIFIED /BASIC/ WIDTH OF THE LINER. 2D AND 1B MODE REPLY22AG691AC20 BZXRD /D/ 18TYPE,CLOTH CLOTH TYPE INDICATES THE TYPE OF CLOTH FROM WHICH THE ITEM IS FABRICATED. SELECT REPLY CODE 10AA62 BZXSD /D/ 07FEATURE,SELF-LOCKING SELF-LOCKING FEATURE AN INDICATION OF WHETHER OR NOT A SELF-LOCKING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BZXTA /D/ 12QUANTITY,KEY,FURNISHED FURNISHED KEY QUANTITY THE NUMBER OF KEYS FURNISHED WITH THE ITEM. 1A MODE REPLY 0 BZXWJ 04WIDTH,FIN FIN WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZXXJ /D/ 04WIDTH,FIN,SECOND SECOND FIN WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZXYJ 04DIAMETER,FIN FIN DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BZXZJ 04DISTANCE FROM FIN TO INSERT HEAD DISTANCE FROM FIN TO INSERT HEAD NONE. 2D AND 1B MODE REPLY21AA051AC20 BZYBJ /D/ 04DISTANCE,FIN TO FIN FIN TO FIN DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 BZYCJ 04DIAMETER,OUTSIDE,TOP UNTHREADED PORTION TOP UNTHREADED PORTION OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 BZYDJ 04LENGTH,OUTSIDE,UNTHREADED,TOP PORTION TOP PORTION UNTHREADED OUTSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZYFJ 04DEPTH,RELIEF,THREAD,INTERNAL INTERNAL THREAD RELIEF DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZYGJ 04THREAD LENGTH,INTERNAL,FULL FULL INTERNAL THREAD LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZYHJ 04LENGTH,OUTSIDE,UNTHREADED,BOTTOM PORTION BOTTOM PORTION UNTHREADED OUTSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 BZYJD /D/ 07FEATURE,DESIGN,COILED WIRE COILED WIRE DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A COILED WIRE DESIGN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BZYKD /D/ 07NOTCH NOTCH AN INDICATION OF WHETHER OR NOT A NOTCH IS INCLUDED. SELECT REPLY CODE 10AA49 BZYLD /D/ 07LEAD ON TOP COIL,SERRATED SERRATED LEAD ON TOP COIL AN INDICATION OF WHETHER OR NOT A SERRATED LEAD ON THE TOP COIL IS INCLUDED. SELECT REPLY CODE 10AA49 BZYMD /D/ 07FEATURE,LOCKING,INTERNAL THREAD INTERNAL THREAD LOCKING FEATURE AN INDICATION OF WHETHER OR NOT AN INTERNAL THREAD LOCKING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 BZYNJ 10SIZE FOR WHICH DESIGNED,RIVET RIVET SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE RIVET FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 BZYPD 18TYPE,FLUSH FLUSH TYPE INDICATES THE TYPE OF FLUSH PROVIDED. SELECT REPLY CODE 10AK54 BZYQJ 04WIDTH,POINT POINT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE POINT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BZYRJ 04DIAMETER FOR WHICH DESIGNED,STUD,SOLID SOLID STUD DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SOLID STUD FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BZYSD 18TYPE ACCOMMODATED,UNIT,PROJECTILE PROJECTILE UNIT TYPE ACCOMMODATED INDICATES THE TYPE OF PROJECTILE UNIT(S) ACCOMMODATED BY THE ITEM. SELECT REPLY CODE 10AK95 BZYTJ 04DIAMETER ACCOMMODATED,UNIT,PROJECTILE PROJECTILE UNIT DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PROJECTILE UNIT ACCOMMODATION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 BZYWD /D/ 07CASE,FITTED FITTED CASE AN INDICATION OF WHETHER OR NOT A FITTED CASE IS PROVIDED. SELECT REPLY CODE 10AB22 BZYXA /D/ 12QUANTITY,FRAME,BEADER BEADER FRAME QUANTITY THE NUMBER OF BEADER FRAMES PROVIDED. 1A MODE REPLY 0 BZYZJ /D/ 04RADIUS,BELLING BELLING RADIUS THE BELLING RADIUS OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 BZZBJ /D/ 04ANGLE IN DEG,FLARE FLARE ANGLE IN DEG THE ANGLE OF THE FLARE,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 BZZCJ 04DIAMETER ACCOMMODATED,MAXIMUM,RIVET RIVET MAXIMUM DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE RIVET ACCOMMODATION,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 BZZDG 19CHARACTERISTICS,ATTACHMENT,PULLING HEAD PULLING HEAD ATTACHMENT CHARACTERISTICS AN INDICATION OF THE CHARACTERISTICS OF THE PULLING HEAD ATTACHMENT. FULL TEXT WRITE-IN 0 BZZFL 16STYLE ACCOMMODATED,SHANK SHANK STYLE ACCOMMODATED THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SHANK THAT WILL ACCOMMODATE THE ITEM. 1L MODE REPLY 0 BZZGD /D/ 07RETURN,PLUNGER,AUTOMATIC RIVET SET AUTOMATIC RIVET SET PLUNGER RETURN AN INDICATION OF WHETHER OR NOT AN AUTOMATIC RIVET SET PLUNGER RETURN IS PROVIDED. SELECT REPLY CODE 10AB22 BZZHG 10CAPACITY,CUTOFF CUTOFF CAPACITY THE CUTOFF CAPACITY OF THE ITEM. FULL TEXT WRITE-IN 0 BZZJJ 10CAPACITY,RIPPING,MAXIMUM MAXIMUM RIPPING CAPACITY THE MAXIMUM RIPPING CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY11AA05 BZZKJ 10REACH,YOKE YOKE REACH THE REACH DISTANCE OF THE YOKE. 1D AND 1B MODE REPLY11AA05 BZZLJ 10GAP,YOKE YOKE GAP A MEASUREMENT OF THE GAP IN THE YOKE. 1D AND 1B MODE REPLY11AA05 BZZMJ 04DISTANCE ACROSS FLATS,BODY BODY DISTANCE ACROSS FLATS THE DISTANCE FROM ONE FLAT TO THE OPPOSITE FLAT OF THE BODY. 2D AND 1B MODE REPLY21AA051AC20 BZZNJ B04SIZE ACCOMMODATED,CROSS-SECTIONAL,RECTANGULAR MATERIAL RECTANGULAR MATERIAL CROSS-SECTIONAL SIZE ACCOMMODATED DESIGNATES THE RECTANGULAR CROSS-SECTIONAL SIZE OF THE MATERIAL ACCOMMODATED BY THE ITEM. 1D AND 1F MODE REPLY11AA05 BZZPJ 04DIAMETER ACCOMMODATED,CROSS-SECTIONAL,ROUND MATERIAL ROUND MATERIAL CROSS-SECTIONAL DIAMETER ACCOMMODATED A MEASUREMENT OF THE ROUND CROSS-SECTIONAL DIAMETER OF THE MATERIAL ACCOMMODATED BY THE ITEM. 1D AND 1B MODE REPLY11AA05 BZZQJ 04LENGTH,BLADE,CUTTING CUTTING BLADE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CUTTING BLADE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BZZRJ 04WIDTH,BLADE,CUTTING CUTTING BLADE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CUTTING BLADE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 BZZSJ 04THICKNESS,BLADE,CUTTING CUTTING BLADE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A CUTTING BLADE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 BZZTJ 10CAPACITY,CUTTING CUTTING CAPACITY THE CUTTING CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY11AA05 BZZWD 19POSITION,AXIS,MOTOR ARMATURE MOTOR ARMATURE AXIS POSITION AN INDICATION OF THE POSITION OF THE MOTOR ARMATURE AXIS. SELECT REPLY CODE 10AG19 BZZXJ 04DEPTH,CUT,VERTICAL VERTICAL CUT DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF A VERTICAL CUT,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 BZZYD /D/ 07ACCOMMODATION,HEAD,DADO DADO HEAD ACCOMMODATION AN INDICATION OF WHETHER OR NOT A DADO HEAD ACCOMMODATION IS INCLUDED. SELECT REPLY CODE 10AA49 BZZZJ 04DIAMETER ACCOMMODATED,ARBOR,BLADE BLADE ARBOR DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR A BLADE ARBOR,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBBBD /D/ 07FEED,RIP,POWER POWER RIP FEED AN INDICATION OF WHETHER OR NOT A POWER RIP FEED IS INCLUDED. SELECT REPLY CODE 10AA49 CBBCD /D/ 07CROSSFEED,POWER POWER CROSSFEED AN INDICATION OF WHETHER OR NOT A POWER CROSSFEED IS INCLUDED. SELECT REPLY CODE 10AA49 CBBDD /D/ 07FEATURE,BRAKE,ELECTRIC,SAW BLADE MOTOR SAW BLADE MOTOR ELECTRIC BRAKE FEATURE AN INDICATION OF WHETHER OR NOT A SAW BLADE MOTOR ELECTRIC BRAKE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CBBFB 10ROTATION IN DEG,ARM ARM ROTATION IN DEG THE ROTATION OF THE ARM,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CBBGB 04ANGLE IN DEG,SWIVEL SWIVEL ANGLE IN DEG THE SWIVEL ANGLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CBBHB 04ANGLE IN DEG,TILT,MOTOR MOTOR TILT ANGLE IN DEG THE TILT ANGLE OF THE MOTOR,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CBBJD /D/ 07FEATURE,ARBOR,TAPPED,CUTTING TOOL CUTTING TOOL TAPPED ARBOR FEATURE AN INDICATION OF WHETHER OR NOT A CUTTING TOOL TAPPED ARBOR FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CBBKD 11METHOD,POWER,ELECTRIC GENERATOR ELECTRIC GENERATOR POWER METHOD THE MEANS USED TO POWER THE ELECTRIC GENERATOR. SELECT REPLY CODE 10AL40 CBBLD 19FEATURES PROVIDED FEATURES PROVIDED THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM. SELECT REPLY CODE 10AN47 CBBMD /D/ 07SUPPORT,TRAILER,RETRACTABLE RETRACTABLE TRAILER SUPPORT AN INDICATION OF WHETHER OR NOT A RETRACTABLE TRAILER SUPPORT(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CBBND /D/ 07WIRE WIRE AN INDICATION OF WHETHER OR NOT A WIRE IS INCLUDED. SELECT REPLY CODE 10AA49 CBBPD /D/ 07STAMPED ON CORE,NUMBER,HEAT HEAT NUMBER STAMPED ON CORE AN INDICATION OF WHETHER OR NOT A HEAT NUMBER STAMPED ON CORE IS INCLUDED. SELECT REPLY CODE 10AA49 CBBQD /D/ 07PROVISION,ATTACHMENT,BLOWOFF LINE BLOWOFF LINE ATTACHMENT PROVISION AN INDICATION OF WHETHER OR NOT A PROVISION FOR ATTACHMENT OF A BLOWOFF LINE IS INCLUDED. SELECT REPLY CODE 10AA49 CBBRD /D/ 18TYPE,LINE,BLOWOFF BLOWOFF LINE TYPE INDICATES THE TYPE OF BLOWOFF LINE PROVIDED. SELECT REPLY CODE 10AK54 CBBSJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,LINE,BLOWOFF BLOWOFF LINE THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE FOR THE BLOWOFF LINE. 1D AND 1A MODE REPLY12AH06 CBBTD /D/ 13THREAD LOCATION,LINE,BLOWOFF BLOWOFF LINE THREAD LOCATION INDICATES THE THREAD LOCATION OF THE BLOWOFF LINE. SELECT REPLY CODE 10AJ91 CBBWJ 04DIAMETER,OUTSIDE,UNTHREADED BLOWOFF LINE UNTHREADED BLOWOFF LINE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE UNTHREADED BLOWOFF LINE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBBXD 03DESIGNATOR,STANDARD STANDARD DESIGNATOR A DESIGNATION INDICATING THE AUTHORITY THAT CONTROLS THE STANDARD FOR THE ITEM. SELECT REPLY CODE 10AJ50 CBBYJ 10TEMP RATING,FUSING,CORE CORE FUSING TEMP RATING THE RATED FUSING TEMPERATURE OF THE CORE AT ITS MELTING POINT. 1D AND 1B MODE REPLY12AB49 CBBZJ 04DIAMETER,CUP CUP DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CUP,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBCBJ /D/ 04LENGTH,CUP CUP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CUP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBCCJ 04HEIGHT,CUP CUP HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE CUP,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CBCDD 02DESIGN,DEVICE,ATTACHMENT ATTACHMENT DEVICE DESIGN THE DESIGN OF THE ATTACHMENT DEVICE. SELECT REPLY CODE 10AG81 CBCFD /D/ 09MATERIAL,DEVICE,ATTACHMENT ATTACHMENT DEVICE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ATTACHMENT DEVICE IS FABRICATED. SELECT REPLY CODE 10AD09 CBCGJ 04LENGTH,DEVICE,ATTACHMENT ATTACHMENT DEVICE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ATTACHMENT DEVICE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBCHJ /D/ 04HEIGHT,LOUVER LOUVER HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE LOUVER,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CBCJD /D/ 07SCREEN,LOUVER LOUVER SCREEN AN INDICATION OF WHETHER OR NOT A LOUVER SCREEN IS PROVIDED. SELECT REPLY CODE 10AB22 CBCKD /D/ 08LOCATION,LOUVER LOUVER LOCATION INDICATES THE LOCATION OF THE LOUVER. SELECT REPLY CODE 10AJ91 CBCLD 18TYPE,SURFACE SURFACE TYPE INDICATES THE TYPE OF SURFACE PROVIDED. SELECT REPLY CODE 10AL59 CBCMA 12QUANTITY,SURFACE SURFACE QUANTITY THE NUMBER OF SURFACES PROVIDED. 1A MODE REPLY 0 CBCNG 04SIZE,FRAME FRAME SIZE DESIGNATES THE SIZE OF THE FRAME. FULL TEXT WRITE-IN 0 CBCPD /D/ 07BRACING,FRAME FRAME BRACING AN INDICATION OF WHETHER OR NOT A FRAME BRACING IS INCLUDED. SELECT REPLY CODE 10AA49 CBCQJ /D/A18TYPE AND QUANTITY,WINDOW WINDOW TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF WINDOWS PROVIDED. 1D AND 1A MODE REPLY13AK54 CBCRD /D/ 09MATERIAL,SASH,WINDOW WINDOW SASH MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WINDOW SASH IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBCSG 08LOCATION,WINDOW WINDOW LOCATION INDICATES THE LOCATION OF THE WINDOW. FULL TEXT WRITE-IN 0 CBCTD /D/ 09MATERIAL,FRAME,WINDOW WINDOW FRAME MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WINDOW FRAME IS FABRICATED. SELECT REPLY CODE 10AD09 CBCWJ /D/ 04THICKNESS,FRAME,WINDOW WINDOW FRAME THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE WINDOW FRAME,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBCXJ /D/ 04WIDTH,FRAME,WINDOW WINDOW FRAME WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE WINDOW FRAME,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CBCYG 08LOCATION,DOOR DOOR LOCATION INDICATES THE LOCATION OF THE DOOR. FULL TEXT WRITE-IN 0 CBCZJ 04THICKNESS,DOOR DOOR THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE DOOR,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBDBD /D/ 09MATERIAL,FRAME,DOOR DOOR FRAME MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE DOOR FRAME IS FABRICATED. SELECT REPLY CODE 10AD09 CBDCJ /D/ 04THICKNESS,FRAME,DOOR DOOR FRAME THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE DOOR FRAME,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBDDJ /D/ 04WIDTH,FRAME,DOOR DOOR FRAME WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE DOOR FRAME,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CBDFJ /D/A18TYPE AND QUANTITY,SCREEN SCREEN TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF SCREENS PROVIDED. 1D AND 1A MODE REPLY13AK54 CBDGD /D/ 09MATERIAL,FRAME,SCREEN SCREEN FRAME MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SCREEN FRAME IS FABRICATED. SELECT REPLY CODE 10AD09 CBDHG /D/ 08LOCATION,SCREEN SCREEN LOCATION INDICATES THE LOCATION OF THE SCREEN. FULL TEXT WRITE-IN 0 CBDJJ /D/ 04HEIGHT,FRAME,SCREEN SCREEN FRAME HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE SCREEN FRAME,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CBDKJ /D/ 04THICKNESS,FRAME,SCREEN SCREEN FRAME THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A SCREEN FRAME,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBDLJ /D/ 04WIDTH,FRAME,SCREEN SCREEN FRAME WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SCREEN FRAME,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CBDMJ /D/A18TYPE AND QUANTITY,SHUTTER SHUTTER TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF SHUTTERS PROVIDED. 1D AND 1A MODE REPLY13AK54 CBDNA 12QUANTITY,OPENING,BARREL BARREL OPENING QUANTITY THE NUMBER OF OPENINGS PROVIDED IN THE BARREL. 1A MODE REPLY 0 CBDPJ 04LENGTH,OPENING,BARREL BARREL OPENING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BARREL OPENING,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CBDQJ 04WIDTH,OPENING,BARREL BARREL OPENING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BARREL OPENING,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CBDRJ 04LENGTH ACCOMMODATED,CARTRIDGE CARTRIDGE LENGTH ACCOMMODATED A MEASUREMENT OF THE LONGEST DIMENSION OF THE CARTRIDGE ACCOMMODATED,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBDSJ 04DIAMETER ACCOMMODATED,CARTRIDGE CARTRIDGE DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED CARTRIDGE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBDTD /D/ 09MATERIAL,BALL,PERFORATED PERFORATED BALL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PERFORATED BALL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBDWD /D/ 17SURFACE TREATMENT,BALL,PERFORATED PERFORATED BALL SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE PERFORATED BALL SURFACE. SELECT REPLY CODE 10AD09 CBDXD 14SHAPE,TUBE TUBE SHAPE THE PHYSICAL CONFIGURATION OF THE TUBE(S). SELECT REPLY CODE 10AD07 CBDYD /D/ 09MATERIAL,END,TUBE TUBE END MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TUBE END IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBDZD /D/ 07ADJUSTABILITY,DELIVERY,PREDETERMINED VOLUME PREDETERMINED VOLUME DELIVERY ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE ITEM IS ADJUSTABLE TO DELIVER PREDETERMINED VOLUME. SELECT REPLY CODE 10AB00 CBFBD /D/ 09MATERIAL,ADAPTER,NOZZLE NOZZLE ADAPTER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE NOZZLE ADAPTER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBFCJ 04LENGTH,ADAPTER,NOZZLE NOZZLE ADAPTER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A NOZZLE ADAPTER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBFDD /D/ 07CONNECTION,THREADED THREADED CONNECTION AN INDICATION OF WHETHER OR NOT A THREADED CONNECTION IS PROVIDED. SELECT REPLY CODE 10AB22 CBFFD /D/ 07CLAMP,CUTOFF CUTOFF CLAMP AN INDICATION OF WHETHER OR NOT A CUTOFF CLAMP(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CBFGD /D/ 09MATERIAL,BAG BAG MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BAG IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBFHJ 04LENGTH,BAG BAG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A BAG,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBFJJ 04WIDTH,BAG BAG WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BAG,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CBFKA 12QUANTITY,NOZZLE,IRRIGATING IRRIGATING NOZZLE QUANTITY THE NUMBER OF IRRIGATING NOZZLES PROVIDED WITH THE ITEM. 1A MODE REPLY 0 CBFLD 18TYPE,NOZZLE,IRRIGATING IRRIGATING NOZZLE TYPE INDICATES THE TYPE OF IRRIGATING NOZZLE(S) PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AK95 CBFMJ 04LENGTH,NOZZLE NOZZLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE NOZZLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBFNJ 04WIDTH,CASE CASE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A CASE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CBFPJ 04LENGTH,CASE CASE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CASE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBFQD /D/ 07SHIELD SHIELD AN INDICATION OF WHETHER OR NOT A SHIELD IS PROVIDED. SELECT REPLY CODE 10AB22 CBFRJ 04LENGTH,TIP,CURVE TO DISTAL CURVE TO DISTAL TIP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CURVE TO DISTAL TIP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBFSJ 04RADIUS,CURVATURE CURVATURE RADIUS THE RADIUS FROM THE CENTER OF THE CIRCLE TO THE OUTSIDE SURFACE. 1D AND 1B MODE REPLY11AA05 CBFTJ 04DIAMETER,HOLE,BOTTOM BASE PLATE STUD BOTTOM BASE PLATE STUD HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOTTOM BASE PLATE STUD HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CBFWJ 04WIDTH,OPENING,CENTRAL CENTRAL OPENING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CENTRAL OPENING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CBFXJ 04LENGTH,OVERALL,CLAMP SCREW CLAMP SCREW OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CLAMP SCREW. 2D AND 1B MODE REPLY21AA051AC20 CBFYD 14SHAPE,END,DISTAL DISTAL END SHAPE THE PHYSICAL CONFIGURATION OF THE DISTAL END(S). SELECT REPLY CODE 10AD07 CBFZA 12QUANTITY,SET,JAW JAW SET QUANTITY THE NUMBER OF JAW SETS PROVIDED. 1A MODE REPLY 0 CBGBD 11METHOD,GRASPING,JAW JAW GRASPING METHOD THE MEANS USED BY THE JAW TO GRASP OR HOLD. SELECT REPLY CODE 10AK54 CBGCJ A12QUANTITY PER JAW,FACILITY,GRASPING GRASPING FACILITY QUANTITY PER JAW THE NUMBER OF GRASPING FACILITIES ON EACH JAW. 1D AND 1A MODE REPLY13AJ91 CBGDD /D/ 08LOCATION,FACILITY,JAW GRASPING JAW GRASPING FACILITY LOCATION INDICATES THE LOCATION OF THE JAW GRASPING FACILITY/IES/. SELECT REPLY CODE 10AJ91 CBGFD 02DESIGN,PATTERN,SERRATED SERRATED PATTERN DESIGN THE DESIGN OF THE SERRATED PATTERN. SELECT REPLY CODE 10AK18 CBGGD /D/ 14SHAPE,BITE,JAW JAW BITE SHAPE THE PHYSICAL CONFIGURATION OF THE JAW BITE. SELECT REPLY CODE 10AD07 CBGHJ /D/ 04LENGTH,BITE BITE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BITE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBGJJ /D/ 04WIDTH,BITE BITE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BITE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CBGKJ /D/ 04DIAMETER,BITE BITE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BITE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBGLD /D/ 19ARRANGEMENT,FACILITY,JAW GRASPING JAW GRASPING FACILITY ARRANGEMENT AN INDICATION OF THE ARRANGEMENT OF THE JAW GRASPING FACILITY/IES/. SELECT REPLY CODE 10AJ91 CBGMJ 04LENGTH,SURFACE,GRASPING,JAW JAW GRASPING SURFACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE JAW GRASPING SURFACE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CBGNJ 04DIAMETER,WHEEL,CASTER CASTER WHEEL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CASTER WHEEL,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CBGPJ /D/ 10SPEED IN RPM,CUTTING,RECOMMENDED RECOMMENDED CUTTING SPEED IN RPM THE RECOMMENDED SPEED AT WHICH THE ITEM HAS BEEN TESTED AND/OR RATED FOR CUTTING,EXPRESSED IN REVOLUTIONS PER MINUTE. 1D AND 1B MODE REPLY11AC20 CBGQG 03DESIGNATION PER FED SPEC/STD 595,COLOR COLOR DESIGNATION PER FED SPEC/STD 595 A COLOR DESIGNATION ASSIGNED TO A PARTICULAR GRADATION OF A COLOR IN ACCORDANCE WITH FEDERAL SPECIFICATION/STANDARD 595 FOR PURPOSE OF READY IDENTIFICATION. FULL TEXT WRITE-IN 0 CBGRD 03DESIGNATION,GLOSS GLOSS DESIGNATION THE DESIGNATOR OR TERM USED TO IDENTIFY THE GLOSS. SELECT REPLY CODE 10AK39 CBGSD 18TYPE,MATERIAL,PIGMENT PIGMENT MATERIAL TYPE INDICATES THE TYPE OF ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PIGMENT IS FABRICATED. SELECT REPLY CODE 10AN48 CBGTD 18TYPE,MATERIAL,VEHICLE VEHICLE MATERIAL TYPE INDICATES THE TYPE OF ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE VEHICLE IS FABRICATED. SELECT REPLY CODE 10AN48 CBGWD /D/ 07FEATURE,FINISH,WRINKLE WRINKLE FINISH FEATURE AN INDICATION OF WHETHER OR NOT A WRINKLE FINISH FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CBGXD 19FINISH FOR WHICH FORMULATED FINISH FOR WHICH FORMULATED AN INDICATION OF THE FINISH FOR WHICH THE ITEM IS FORMULATED. SELECT REPLY CODE 10AA41 CBGYD /D/ 07PIGMENT,ALUMINUM ALUMINUM PIGMENT AN INDICATION OF WHETHER OR NOT AN ALUMINUM PIGMENT IS INCLUDED. SELECT REPLY CODE 10AA49 CBGZD 18TYPE,PACKAGE,SEPARATE,PIGMENT PIGMENT SEPARATE PACKAGE TYPE INDICATES THE TYPE OF SEPARATE PACKAGE IN WHICH THE PIGMENT IS CONTAINED. SELECT REPLY CODE 10AE96 CBHBD /D/ 07FORM,PASTE PASTE FORM AN INDICATION OF WHETHER OR NOT A PASTE FORM IS INCLUDED. SELECT REPLY CODE 10AA49 CBHCB 10PERCENTAGE,MINIMUM,NONVOLATILE MATERIAL NONVOLATILE MATERIAL MINIMUM PERCENTAGE THE MINIMUM PERCENT OF NONVOLATILE MATERIAL INCLUDED IN THE ITEM. 1B MODE REPLY 0 CBHDJ /D/ 10WEIGHT AND TYPE,MATERIAL,RETRODIRECTIVE RETRODIRECTIVE MATERIAL WEIGHT AND TYPE THE WEIGHT AND TYPE OF RETRODIRECTIVE MATERIAL INCLUDED IN THE ITEM. 3D AND 1B MODE REPLY32AB491AC204AE98 CBHFD /D/ 07FEATURE,THINNING,WHITE GASOLINE ONLY WHITE GASOLINE ONLY THINNING FEATURE AN INDICATION OF WHETHER OR NOT A WHITE GASOLINE ONLY THINNING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CBHGD /D/ 07FEATURE,BAKE DRY ONLY BAKE DRY ONLY FEATURE AN INDICATION OF WHETHER OR NOT A BAKE DRY ONLY FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CBHHD /D/ 19MEDIUM FOR WHICH DESIGNED,REMOVAL REMOVAL MEDIUM FOR WHICH DESIGNED AN INDICATION OF THE REMOVAL MEDIUM FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AB75 CBHJD /D/ 07OIL,WATER-DISPERSIBLE,SEPARATE SEPARATE WATER-DISPERSIBLE OIL AN INDICATION OF WHETHER OR NOT A SEPARATE WATER-DISPERSIBLE OIL/S/ IS FURNISHED. SELECT REPLY CODE 10AA55 CBHKB /D/ 10WEIGHT IN PERCENT,CONTENT,MINIMUM PORTLAND CEMENT MINIMUM PORTLAND CEMENT CONTENT WEIGHT IN PERCENT THE MINIMUM PORTLAND CEMENT CONTENT BY WEIGHT,EXPRESSED IN PERCENT. 1B MODE REPLY 0 CBHLD /D/ 07AGGREGATE,SILICEOUS SILICEOUS AGGREGATE AN INDICATION OF WHETHER OR NOT A SILICEOUS AGGREGATE IS INCLUDED. SELECT REPLY CODE 10AA49 CBHMD /D/ 07PIGMENT,OXIDE,ZINC ZINC OXIDE PIGMENT AN INDICATION OF WHETHER OR NOT A ZINC OXIDE PIGMENT IS INCLUDED. SELECT REPLY CODE 10AA49 CBHNJ 10TIME,DRYING,AIR,RECOATING RECOATING AIR DRYING TIME AN INDICATION OF THE AIR DRYING TIME REQUIRED FOR RECOATING. 2D AND 1B MODE REPLY22AG671AC20 CBHPD 18TYPE,MATERIAL,BASIC BASIC MATERIAL TYPE INDICATES THE TYPE OF ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BASIC MATERIAL IS FABRICATED. SELECT REPLY CODE 10AN48 CBHQD 11METHOD,COLORING COLORING METHOD THE MEANS USED TO COLOR THE ITEM. SELECT REPLY CODE 10AM39 CBHRD 03DESIGNATION,STRENGTH,BODY BODY STRENGTH DESIGNATION A DESIGNATION INDICATING THE STRENGTH OF THE BODY. SELECT REPLY CODE 10AJ87 CBHSB 10GLOSS RATING,SPECULAR,60 DEG 60 DEG SPECULAR GLOSS RATING THE 60 DEGREE SPECULAR GLOSS RATING OF THE ITEM. 1B MODE REPLY 0 CBHTD /D/ 07FEATURE,FUNGICIDAL FUNGICIDAL FEATURE AN INDICATION OF WHETHER OR NOT A FUNGICIDAL FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CBHWD 19DERIVATIVE,CELLULOSIC CELLULOSIC DERIVATIVE THE BASIC INGREDIENT(S) FROM WHICH THE ITEM IS DERIVED. SELECT REPLY CODE 10AJ06 CBHXD 18TYPE,MATERIAL,RESIN RESIN MATERIAL TYPE INDICATES THE TYPE OF ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE RESIN IS FABRICATED. SELECT REPLY CODE 10AN48 CBHYB 10REDUCTION IN PERCENT,KAURI KAURI REDUCTION IN PERCENT AN INDICATION OF THE KAURI REDUCTION OF THE ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 CBHZG /D/ 10VISCOSITY RATING IN GARDNER-HOLDT UNITS VISCOSITY RATING IN GARDNER-HOLDT UNITS AN INDICATION OF THE VISCOSITY RATING,EXPRESSED IN GARDNER-HOLDT UNITS. FULL TEXT WRITE-IN 0 CBJBG /D/ 19CONTROLLER,SAMPLE,GOVERNMENT AGENCY STANDARD GOVERNMENT AGENCY STANDARD SAMPLE CONTROLLER THE NAME OF THE GOVERNMENT AGENCY WHICH CONTROLS THE STANDARD SAMPLE/S/. FULL TEXT WRITE-IN 0 CBJCD 18TYPE,LINING LINING TYPE INDICATES THE TYPE OF LINING PROVIDED. SELECT REPLY CODE 10AK54 CBJDD 03DESIGNATION,SHADE SHADE DESIGNATION A DESIGNATION OF THE DENSITY OF THE SHADE. SELECT REPLY CODE 10AN49 CBJFD /D/ 07FEATURE,NONBLEEDING NONBLEEDING FEATURE AN INDICATION OF WHETHER OR NOT A NONBLEEDING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CBJGJ T10RANGE,TEMP,DISTILLATION DISTILLATION TEMP RANGE THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH DISTILLATION TAKES PLACE. 1D AND 1F MODE REPLY13AJ40 CBJHD 18TYPE FOR WHICH DESIGNED,MATERIAL MATERIAL TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF MATERIAL FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AN48 CBJJD /D/ 07FEATURE,RETARDANT BLUSH BLUSH RETARDANT FEATURE AN INDICATION OF WHETHER OR NOT A BLUSH RETARDANT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CBJKA 19NUMBER,IODINE,MINIMUM MINIMUM IODINE NUMBER THE MINIMUM IODINE NUMBER OF THE ITEM. 1A MODE REPLY 0 CBJLD 18TYPE,MATERIAL MATERIAL TYPE INDICATES THE TYPE OF MATERIAL COMPOSING THE ITEM. SELECT REPLY CODE 10AN48 CBJMD /D/ 07SOLVENT SOLVENT AN INDICATION OF WHETHER OR NOT A SOLVENT IS INCLUDED. SELECT REPLY CODE 10AA49 CBJNJ 04LENGTH,JAW JAW LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE JAW,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBJPD 11METHOD,RETAINING,COMPRESSION COMPRESSION RETAINING METHOD THE MEANS USED TO RETAIN COMPRESSION. SELECT REPLY CODE 10AE36 CBJQD /D/ 07SPRING,DISTENDING DISTENDING SPRING AN INDICATION OF WHETHER OR NOT A DISTENDING SPRING(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CBJRD /D/ 07PIN,GUIDE GUIDE PIN AN INDICATION OF WHETHER OR NOT A GUIDE PIN(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CBJSD /D/ 08LOCATION,PIN,GUIDE GUIDE PIN LOCATION INDICATES THE LOCATION OF THE GUIDE PIN ON THE ITEM. SELECT REPLY CODE 10AJ91 CBJTJ 10CLEARANCE REQUIRED,MINIMUM MINIMUM CLEARANCE REQUIRED THE MINIMUM CLEARANCE REQUIRED FOR THE ITEM. 1D AND 1B MODE REPLY11AA05 CBJWD /D/ 07CLIPPER CLIPPER AN INDICATION OF WHETHER OR NOT A CLIPPER(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CBJXD /D/ 07BLOCK,STRIKING STRIKING BLOCK AN INDICATION OF WHETHER OR NOT A STRIKING BLOCK(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CBJYD /D/ 07RING,METAL METAL RING AN INDICATION OF WHETHER OR NOT A METAL RING(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CBJZD /D/ 18TYPE FOR WHICH DESIGNED,HANDPIECE HANDPIECE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF HANDPIECE FOR WHICH THE ITEM IS DESIGNED TO BE USED. SELECT REPLY CODE 10AK54 CBKBA /D/ 16STYLE,TIP TIP STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TIP. 1A MODE REPLY 0 CBKCD /D/ 07TIP,PLATINUM PLATINUM TIP AN INDICATION OF WHETHER OR NOT A PLATINUM TIP IS PROVIDED. SELECT REPLY CODE 10AB22 CBKDJ /D/ 04DIAMETER ACCOMMODATED,DRILL DRILL DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE DRILL,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CBKFJ /D/ 04LENGTH,TIP,GUIDE GUIDE TIP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE GUIDE TIP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBKGD /D/ 07ACCOMMODATION,CHUCK,JACOBS JACOBS CHUCK ACCOMMODATION AN INDICATION OF WHETHER OR NOT A JACOBS CHUCK ACCOMMODATION/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 CBKHD /D/ 07HOLE,EXTRACTOR EXTRACTOR HOLE AN INDICATION OF WHETHER OR NOT AN EXTRACTOR HOLE(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CBKJD 18TYPE,OPENING,SLOTTED SLOTTED OPENING TYPE INDICATES THE TYPE OF SLOTTED OPENING(S) PROVIDED. SELECT REPLY CODE 10AK54 CBKKG 03DESIGNATION,SIZE,WIRE WIRE SIZE DESIGNATION THE SIZE BY WHICH THE WIRE IS COMMERCIALLY KNOWN AND/OR DESIGNATED. FULL TEXT WRITE-IN 0 CBKLA 03DESIGNATION,SIZE,HEAD HEAD SIZE DESIGNATION THE RECOGNIZED TRADE DESIGNATION OR TERM INDICATING THE HEAD SIZE. 1A MODE REPLY 0 CBKMJ 04DIAMETER,OVERALL,HEAD HEAD OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE CIRCULAR CROSS-SECTIONAL PLANE OF THE HEAD. 1D AND 1B MODE REPLY11AA05 CBKND /D/ 07FEATURE,CROSSCUT,HEAD HEAD CROSSCUT FEATURE AN INDICATION OF WHETHER OR NOT A HEAD CROSSCUT FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CBKPD /D/ 07FEATURE,SHAPE,PREFORMED PREFORMED SHAPE FEATURE AN INDICATION OF WHETHER OR NOT A PREFORMED SHAPE FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CBKQD /D/ 03DESIGNATION,SIZE,NECK NECK SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE NECK IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. SELECT REPLY CODE 10AF81 CBKRD /D/ 18TYPE FOR WHICH DESIGNED,SNARE SNARE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF SNARE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 CBKSJ 04WIDTH,OVERALL,TIP TIP OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A TIP,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CBKTJ /D/ 04DIAMETER,OVERALL OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE. 2D AND 1B MODE REPLY21AF981AC20 CBKWD /D/ 07TIP,FLUTED,SPIRAL SPIRAL FLUTED TIP AN INDICATION OF WHETHER OR NOT A SPIRAL FLUTED TIP(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CBKXJ 04DIAMETER,OVERALL,BLADE BLADE OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE CIRCULAR CROSS-SECTIONAL PLANE OF THE BLADE. 1D AND 1B MODE REPLY11AA05 CBKYD /D/ 14SHAPE,CROSS-SECTIONAL,SHANK SHANK CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE SHANK WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 CBKZD /D/ 03DESIGNATION,DESIGN,SHANK SHANK DESIGN DESIGNATION THE DESIGNATION DERIVED FROM THE NAME OF THE DESIGNER BY WHICH THE SHANK IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. SELECT REPLY CODE 10AJ50 CBLBJ 04LENGTH,OVERALL,SHANK SHANK OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE SHANK. 1D AND 1B MODE REPLY11AA05 CBLCA 12QUANTITY,CANNULA CANNULA QUANTITY THE NUMBER OF CANNULAS PROVIDED. 1A MODE REPLY 0 CBLDJ 04LENGTH,CANNULA CANNULA LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CANNULA,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CBLFJ 04DIAMETER,CANNULA CANNULA DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CANNULA,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CBLGA 12QUANTITY,WIRE,SNARE SNARE WIRE QUANTITY THE NUMBER OF SNARE WIRES PROVIDED. 1A MODE REPLY 0 CBLHD 18TYPE,WIRE,SNARE SNARE WIRE TYPE INDICATES THE TYPE OF SNARE WIRE PROVIDED. SELECT REPLY CODE 10AK54 CBLJD /D/ 07INSULATION,ELECTRICAL ELECTRICAL INSULATION AN INDICATION OF WHETHER OR NOT ELECTRICAL INSULATION IS INCLUDED. SELECT REPLY CODE 10AA49 CBLKD /D/ 07WRENCH WRENCH AN INDICATION OF WHETHER OR NOT A WRENCH IS PROVIDED. SELECT REPLY CODE 10AB22 CBLLD /D/ 18TYPE,DEVICE,SELECTOR SELECTOR DEVICE TYPE INDICATES THE TYPE OF SELECTOR DEVICE PROVIDED. SELECT REPLY CODE 10AK54 CBLMJ /D/ 04LENGTH,OVERALL,BATTERY BATTERY OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BATTERY. 1D AND 1B MODE REPLY11AA05 CBLNA /D/ 12QUANTITY,ACCOMMODATED,PROJECTILE PROJECTILE ACCOMMODATED QUANTITY THE NUMBER OF PROJECTILES THAT THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 CBLPA 12QUANTITY ACCOMMODATED,WEAPON WEAPON QUANTITY ACCOMMODATED THE NUMBER OF WEAPONS THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 CBLQJ 04WIDTH,OVERALL,TOP TOP OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TOP OF AN ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CBLRJ 04WIDTH,OVERALL,BOTTOM BOTTOM OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BOTTOM OF AN ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CBLSD 11METHOD,EJECTION EJECTION METHOD THE MEANS BY WHICH THE ITEM IS EJECTED. SELECT REPLY CODE 10AG89 CBLTA 12QUANTITY,TUBE,BOMB BOMB TUBE QUANTITY THE NUMBER OF BOMB TUBES PROVIDED. 1A MODE REPLY 0 CBLWA 19NUMBER FOR WHICH DESIGNED,MODEL,BOMB BOMB MODEL NUMBER FOR WHICH DESIGNED THE MODEL NUMBER OF THE BOMB FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 CBLXH /D/ 18TYPE AND LOCATION,CONTAINER,DISPENSING DISPENSING CONTAINER TYPE AND LOCATION INDICATES THE TYPE OF DISPENSING CONTAINER AND ITS LOCATION. 2D MODE REPLY 22AF723AJ91 CBLYD /D/ 18TYPE,PROPELLANT,FLAME FLAME PROPELLANT TYPE INDICATES THE TYPE OF FLAME PROPELLANT PROVIDED. SELECT REPLY CODE 10AB75 CBLZG /D/ 19VEHICLE FOR WHICH SERVING AS ARMAMENT VEHICLE FOR WHICH SERVING AS ARMAMENT INDICATES THE VEHICLE(S) ON WHICH THE ITEM MAY SERVE AS ARMAMENT. FULL TEXT WRITE-IN 0 CBMBG 19WEAPON AND CALIBER FOR WHICH DESIGNED WEAPON AND CALIBER FOR WHICH DESIGNED AN INDICATION OF THE WEAPON AND CALIBER FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 CBMCD 02DESIGN,POSITION,WEARING WEARING POSITION DESIGN THE DESIGN OF THE ITEM INDICATING ITS WEARING POSITION. SELECT REPLY CODE 10AM84 CBMDD /D/ 09MATERIAL,STIFFENER STIFFENER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH A STIFFENER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBMEJ 10CUBIC MEASURE CUBIC MEASURE A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS. 1D AND 1B MODE REPLY12AN76 CBMFD 08LOCATION,WEARING WEARING LOCATION INDICATES THE LOCATION OF THE ITEM WHEN WORN. SELECT REPLY CODE 10AJ91 CBMGG 11METHOD,ATTACHMENT TO BELT ATTACHMENT TO BELT METHOD THE MEANS BY WHICH THE ITEM IS ATTACHED TO THE BELT. FULL TEXT WRITE-IN 0 CBMHA 04SIZE,SIMULATED SIMULATED SIZE DESIGNATES THE SIZE OF THE SIMULATED ITEM. 1A MODE REPLY 0 CBMJD 18TYPE,SUPPORT,BASE BASE SUPPORT TYPE INDICATES THE TYPE OF BASE SUPPORT PROVIDED. SELECT REPLY CODE 10AM61 CBMKD 19DEG,FIDELITY FIDELITY DEG THE DEGREE OF FIDELITY OF THE ITEM. SELECT REPLY CODE 10AF07 CBMLD /D/ 09MATERIAL,FORM FORM MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FORM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBMMJ 04LENGTH FOR WHICH DESIGNED,BLADE BLADE LENGTH FOR WHICH DESIGNED A MEASUREMENT OF THE LONGEST DIMENSION OF THE BLADE FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBMNA 12QUANTITY,TUBE,CLUSTER CLUSTER TUBE QUANTITY THE NUMBER OF TUBES IN THE CLUSTER. 1A MODE REPLY 0 CBMPD 18TYPE,BRIDLE BRIDLE TYPE INDICATES THE TYPE OF BRIDLE PROVIDED. SELECT REPLY CODE 10AK54 CBMQA 12QUANTITY,LEG,FORWARD FORWARD LEG QUANTITY THE NUMBER OF FORWARD LEGS PROVIDED. 1A MODE REPLY 0 CBMRJ 04LENGTH,LEG,FORWARD FORWARD LEG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FORWARD LEG,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBMSA 04SIZE,CHAIN,FORWARD LEG FORWARD LEG CHAIN SIZE DESIGNATES THE SIZE BY WHICH THE FORWARD LEG CHAIN IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1A MODE REPLY 0 CBMTD /D/ 09MATERIAL,LEG,FORWARD FORWARD LEG MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FORWARD LEG IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBMWA 12QUANTITY,LEG,AFTER AFTER LEG QUANTITY THE NUMBER OF AFTER LEGS PROVIDED. 1A MODE REPLY 0 CBMXJ 04LENGTH,LEG,AFTER AFTER LEG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE AFTER LEG,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBMYA 04SIZE,CHAIN,AFTER LEG AFTER LEG CHAIN SIZE DESIGNATES THE SIZE BY WHICH THE AFTER LEG CHAIN IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1A MODE REPLY 0 CBMZD /D/ 09MATERIAL,LEG,AFTER AFTER LEG MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE AFTER LEG IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBNBD 18TYPE,ATTACHMENT,COMMON COMMON ATTACHMENT TYPE INDICATES THE TYPE OF COMMON ATTACHMENT PROVIDED. SELECT REPLY CODE 10AJ74 CBNCD /D/ 09MATERIAL,ATTACHMENT,COMMON COMMON ATTACHMENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE COMMON ATTACHMENT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBNDD /D/ 07LEG,BEAM,UPPER UPPER BEAM LEG AN INDICATION OF WHETHER OR NOT AN UPPER BEAM LEG IS INCLUDED. SELECT REPLY CODE 10AA49 CBNFJ 04LENGTH,LEG,UPPER BEAM UPPER BEAM LEG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE UPPER BEAM LEG,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBNGD /D/ 09MATERIAL,LEG,UPPER BEAM UPPER BEAM LEG MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE UPPER BEAM LEG IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBNHD /D/ 07LEG,BEAM,MIDDLE MIDDLE BEAM LEG AN INDICATION OF WHETHER OR NOT A MIDDLE BEAM LEG IS INCLUDED. SELECT REPLY CODE 10AA49 CBNJJ 04LENGTH,LEG,MIDDLE BEAM MIDDLE BEAM LEG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE MIDDLE BEAM LEG,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBNKD /D/ 09MATERIAL,LEG,MIDDLE BEAM MIDDLE BEAM LEG MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MIDDLE BEAM LEG IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBNLD /D/ 07LEG,BEAM,LOWER LOWER BEAM LEG AN INDICATION OF WHETHER OR NOT A LOWER BEAM LEG IS INCLUDED. SELECT REPLY CODE 10AA49 CBNMJ 04LENGTH,LEG,LOWER BEAM LOWER BEAM LEG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE LOWER BEAM LEG,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBNND /D/ 09MATERIAL,SHUTTER SHUTTER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHUTTER IS FABRICATED. SELECT REPLY CODE 10AD09 CBNPG /D/ 08LOCATION,SHUTTER SHUTTER LOCATION INDICATES THE LOCATION OF THE SHUTTER. FULL TEXT WRITE-IN 0 CBNQJ /D/ 04HEIGHT,SHUTTER SHUTTER HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE SHUTTER,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CBNRJ /D/ 04THICKNESS,SHUTTER SHUTTER THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE SHUTTER,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBNSJ /D/ 04WIDTH,SHUTTER SHUTTER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SHUTTER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CBNTJ /D/A18TYPE AND QUANTITY,VENT VENT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF VENTS PROVIDED. 1D AND 1A MODE REPLY13AK54 CBNWD /D/ 09MATERIAL,VENT VENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE VENT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBNXJ /D/ 04HEIGHT,VENT VENT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE VENT,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CBNYJ /D/ 04THICKNESS,VENT VENT THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE VENT,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBNZJ /D/ 04WIDTH,VENT VENT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE VENT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CBPBG /D/ 08LOCATION,ITEM,ELECTRICAL ELECTRICAL ITEM LOCATION INDICATES THE LOCATION OF THE ELECTRICAL ITEM. FULL TEXT WRITE-IN 0 CBPCJ /D/A19NAME AND QUANTITY,COMPONENT,ELECTRICAL ELECTRICAL COMPONENT NAME AND QUANTITY THE NAME AND NUMBER OF THE ELECTRICAL COMPONENTS THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1A MODE REPLY13AL83 CBPDG /D/ 19NAME AND QUANTITY,FACILITY,PLUMBING PLUMBING FACILITY NAME AND QUANTITY THE NAME AND NUMBER OF THE PLUMBING FACILITY THE ITEM IS DESIGNED TO ACCOMMODATE. FULL TEXT WRITE-IN 0 CBPFG /D/ 08LOCATION,FACILITY,PLUMBING PLUMBING FACILITY LOCATION INDICATES THE LOCATION OF THE PLUMBING FACILITY(IES). FULL TEXT WRITE-IN 0 CBPGG 19AGENCY,CONTROLLING,REQUIRED SUPPORT REQUIRED SUPPORT CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION THAT CONTROLS THE MANUFACTURE OF THE REQUIRED SUPPORT. FULL TEXT WRITE-IN 0 CBPHG 19NAME,EQUIPMENT,REQUIRED SUPPORT REQUIRED SUPPORT EQUIPMENT NAME THE NAME BY WHICH THE REQUIRED SUPPORT EQUIPMENT IS KNOWN. FULL TEXT WRITE-IN 0 CBPJG /D/ 03DESIGNATOR,IDENTIFICATION,REQUIRED SUPPORT REQUIRED SUPPORT IDENTIFICATION DESIGNATOR A DESIGNATION ASSIGNED TO THE REQUIRED SUPPORT FOR PURPOSE OF READY IDENTIFICATION. FULL TEXT WRITE-IN 0 CBPKD /D/ 07STAVES STAVES AN INDICATION OF WHETHER OR NOT STAVES ARE INCLUDED. SELECT REPLY CODE 10AA49 CBPLD /D/ 07WIRES,GUY GUY WIRES AN INDICATION OF WHETHER OR NOT GUY WIRES ARE INCLUDED. SELECT REPLY CODE 10AA49 CBPMD /D/ 07ATTACHMENT,BAR,SPRAY SPRAY BAR ATTACHMENT AN INDICATION OF WHETHER OR NOT A SPRAY BAR ATTACHMENT IS INCLUDED. SELECT REPLY CODE 10AA49 CBPND 19EXTENT,INSULATION,WEATHER WEATHER INSULATION EXTENT AN INDICATION OF THE EXTENT OF WEATHER INSULATION PROVIDED. SELECT REPLY CODE 10AK95 CBPPD /D/ 07FEATURE,SHIELDED,ELECTRICALLY ELECTRICALLY SHIELDED FEATURE AN INDICATION OF WHETHER OR NOT AN ELECTRICALLY SHIELDED FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 CBPQD 18TYPE,WELD WELD TYPE INDICATES THE TYPE OF WELD PROVIDED. SELECT REPLY CODE 10AD07 CBPRD /D/ 09MATERIAL,GASKET GASKET MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE GASKET IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBPSJ 04THICKNESS,MATERIAL,SHELL SHELL MATERIAL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE SHELL MATERIAL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBPTJ 04THICKNESS,MATERIAL,END END MATERIAL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE END MATERIAL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBPWD /D/ 09MATERIAL,END END MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE END IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBPXD /D/ 07FEATURE,COMPARTMENT,TWO TWO COMPARTMENT FEATURE AN INDICATION OF WHETHER OR NOT A TWO COMPARTMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CBPYD /D/ 09MATERIAL,BOTTOM BOTTOM MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BOTTOM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBPZJ 04THICKNESS,MATERIAL,BOTTOM BOTTOM MATERIAL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE BOTTOM MATERIAL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBQBD /D/ 07TOP TOP AN INDICATION OF WHETHER OR NOT A TOP IS INCLUDED. SELECT REPLY CODE 10AA49 CBQCJ 04THICKNESS,MATERIAL,TOP TOP MATERIAL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE TOP MATERIAL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBQDA 12QUANTITY,BRACKET BRACKET QUANTITY THE NUMBER OF BRACKETS PROVIDED. 1A MODE REPLY 0 CBQFJ A18TYPE AND QUANTITY,MANHOLE MANHOLE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF MANHOLES PROVIDED. 1D AND 1A MODE REPLY12AA78 CBQGD 11METHOD,MOUNTING,MANHOLE MANHOLE MOUNTING METHOD THE MEANS OF ATTACHING THE MANHOLE. SELECT REPLY CODE 10AM39 CBQHG 08LOCATION,MANHOLE MANHOLE LOCATION INDICATES THE LOCATION OF THE MANHOLE. FULL TEXT WRITE-IN 0 CBQJD 14SHAPE,MANHOLE MANHOLE SHAPE THE PHYSICAL CONFIGURATION OF THE MANHOLE. SELECT REPLY CODE 10AD07 CBQKD 18TYPE,CLEANOUT CLEANOUT TYPE INDICATES THE TYPE OF CLEANOUT PROVIDED ON THE ITEM. SELECT REPLY CODE 10AK54 CBQLG 08LOCATION,CLEANOUT CLEANOUT LOCATION INDICATES THE LOCATION OF THE CLEANOUT. FULL TEXT WRITE-IN 0 CBQMD 14SHAPE,CLEANOUT CLEANOUT SHAPE THE PHYSICAL CONFIGURATION OF THE CLEANOUT. SELECT REPLY CODE 10AD07 CBQND 11METHOD,LOCKING LOCKING METHOD THE MEANS BY WHICH THE ITEM IS LOCKED. SELECT REPLY CODE 10AE44 CBQPA /D/ 12QUANTITY,COIL,GRIP GRIP COIL QUANTITY THE NUMBER OF GRIP COILS PROVIDED. 1A MODE REPLY 0 CBQQD /D/ 17SURFACE TREATMENT,PLATE PLATE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE PLATE SURFACE. SELECT REPLY CODE 10AD09 CBQRD /D/ 17SURFACE TREATMENT,BAR BAR SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS THAT PROTECTS A BAR SURFACE. SELECT REPLY CODE 10AD09 CBQSD 11METHOD,MOUNTING,CASE CASE MOUNTING METHOD THE MEANS OF ATTACHING THE CASE. SELECT REPLY CODE 10AM39 CBQTA 12QUANTITY,STRIKE STRIKE QUANTITY THE NUMBER OF STRIKES PROVIDED. 1A MODE REPLY 0 CBQWD 18TYPE,STRIKE STRIKE TYPE INDICATES THE TYPE OF STRIKE PROVIDED. SELECT REPLY CODE 10AG25 CBQXD /D/ 14SHAPE,BAR BAR SHAPE THE PHYSICAL CONFIGURATION OF THE BAR. SELECT REPLY CODE 10AD07 CBQYJ /D/ 04DIAMETER,BAR BAR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BAR,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBQZJ /D/ 04LENGTH,OVERALL,BAR BAR OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BAR. 2D AND 1B MODE REPLY21AA051AC20 CBRBG /D/ 04SIZE,BASE BASE SIZE DESIGNATES THE SIZE OF THE TOTAL SURFACE OF THE BASE. FULL TEXT WRITE-IN 0 CBRCH /D/ 19NAME AND MATERIAL,COMPONENT COMPONENT NAME AND MATERIAL THE NAME OF THE COMPONENT/S/,AND THE ELEMENTS,COMPOUND,OR MIXTURE OF WHICH THE COMPONENT/S/ IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. 2D MODE REPLY 23AL836AD09 CBRDH /D/ 19NAME AND SURFACE TREATMENT,COMPONENT COMPONENT NAME AND SURFACE TREATMENT THE NAME OF THE COMPONENT AND THE PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE COMPONENT SURFACE. 2D MODE REPLY 23AL836AD09 CBRFJ /D/ 04THICKNESS FOR WHICH CLAMP IS DESIGNED,MATERIAL MATERIAL THICKNESS FOR WHICH CLAMP IS DESIGNED A MEASUREMENT OF THE SMALLEST DIMENSION OF THE MATERIAL WHICH THE CLAMP IS DESIGNED TO HOLD. 2D AND 1B MODE REPLY21AA051AC20 CBRGJ /D/ 04DIAMETER FOR WHICH CLAMP IS DESIGNED,MATERIAL MATERIAL DIAMETER FOR WHICH CLAMP IS DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MATERIAL FOR WHICH THE CLAMP IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBRHJ /D/ 09MATERIAL AND PERCENTAGE,BLENDED BLENDED MATERIAL AND PERCENTAGE THE BLENDED MATERIAL OF WHICH THE ITEM IS FABRICATED AND THE PERCENTAGE OF EACH MATERIAL. 1D AND 1B MODE REPLY16AD09 CBRJJ 04LENGTH,CLOSED CLOSED LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN OBJECT WHEN CLOSED,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBRKD /D/ 07WALL,INSIDE,CORRUGATED CORRUGATED INSIDE WALL AN INDICATON OF WHETHER OR NOT A CORRUGATED INSIDE WALL IS INCLUDED. SELECT REPLY CODE 10AA49 CBRLD 14SHAPE,SURFACE,WEARING WEARING SURFACE SHAPE THE PHYSICAL CONFIGURATION OF THE WEARING SURFACE. SELECT REPLY CODE 10AD07 CBRMD 19CONDITION,SURFACE,WEARING WEARING SURFACE CONDITION THE CONDITION OF THE ITEM WITH RESPECT TO THE TEXTURE OF THE WEARING SURFACE. SELECT REPLY CODE 10AK39 CBRND /D/ 07SECTION,BASE,METAL DISK ON INSIDE SURFACE METAL DISK ON INSIDE SURFACE BASE SECTION AN INDICATION OF WHETHER OR NOT A METAL DISK ON THE INSIDE SURFACE OF THE BASE SECTION IS INCLUDED. SELECT REPLY CODE 10AA49 CBRPJ /D/ 04DIAMETER,OUTSIDE,LEG TUBING LEG TUBING OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LEG TUBING,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBRQD 18TYPE,CUSHIONING CUSHIONING TYPE INDICATES THE TYPE OF CUSHIONING PROVIDED. SELECT REPLY CODE 10AC52 CBRRD /D/ 09MATERIAL,PLATE,PATCH PATCH PLATE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PATCH PLATE(S) IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBRSD /D/ 17SURFACE TREATMENT,PLATE,PATCH PATCH PLATE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING WHICH CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE PATCH PLATE SURFACE. SELECT REPLY CODE 10AD09 CBRTJ 04DIAMETER,PLATE,PATCH PATCH PLATE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR PATCH PLATE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBRWJ 04THICKNESS,MATERIAL,PATCH PLATE PATCH PLATE MATERIAL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE PATCH PLATE MATERIAL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBRXD /D/ 07FEATURE,ANTITURN,KEYED,PATCH PLATE PATCH PLATE KEYED ANTITURN FEATURE AN INDICATION OF WHETHER OR NOT A PATCH PLATE KEYED ANTITURN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CBRYD /D/ 09MATERIAL,SCREW SCREW MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SCREW IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBRZD /D/ 17SURFACE TREATMENT,SCREW SCREW SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SCREW SURFACE. SELECT REPLY CODE 10AD09 CBSBB /D/ 04ANGLE IN DEG,COUNTERSINK,SCREW HEAD SCREW HEAD COUNTERSINK ANGLE IN DEG THE ANGLE OF THE SCREW HEAD COUNTERSINK,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CBSCD 18TYPE,DRIVE,SCREW SCREW DRIVE TYPE INDICATES THE TYPE OF DRIVE PROVIDED FOR TURNING,ROTATING,OR POSITIONING THE SCREW. SELECT REPLY CODE 10AG25 CBSDA /D/ 13THREAD SIZE,SCREW SCREW THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A SCREW. 1A MODE REPLY 0 CBSFJ /D/ 04LENGTH,SCREW SCREW LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SCREW,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBSGD /D/ 09MATERIAL,NUT NUT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE NUT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBSHD /D/ 17SURFACE TREATMENT,NUT NUT SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE NUT SURFACE. SELECT REPLY CODE 10AD09 CBSJJ 04THICKNESS,MATERIAL,NUT NUT MATERIAL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A NUT,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBSKJ /D/ 04DIAMETER,OUTSIDE,BEARING AREA BEARING AREA OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BEARING AREA,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBSLG /D/ 19SPEC/STD,MATERIAL,TUBE TUBE MATERIAL SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE TUBE MATERIAL. FULL TEXT WRITE-IN 0 CBSMJ 04DIAMETER FOR WHICH DESIGNED,CABLE CABLE DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CABLE FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBSNJ /D/ 04DIAMETER,OVERALL,BATTERY BATTERY OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE CIRCULAR CROSS-SECTIONAL PLANE OF A BATTERY. 1D AND 1B MODE REPLY11AA05 CBSPD /D/ 07CONTROL,RHEOSTAT RHEOSTAT CONTROL AN INDICATION OF WHETHER OR NOT A RHEOSTAT CONTROL(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CBSQD /D/ 07REMOVABILITY,SECTION,TUBE WALL TUBE WALL SECTION REMOVABILITY AN INDICATION OF WHETHER OR NOT THE TUBE WALL SECTION IS REMOVABLE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. SELECT REPLY CODE 10AC29 CBSRD /D/ 08LOCATION,SECTION SECTION LOCATION INDICATES THE LOCATION OF A SECTION. SELECT REPLY CODE 10AJ91 CBSSJ 04LENGTH,OVERALL,TUBE TUBE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE TUBE. 1D AND 1B MODE REPLY11AA05 CBSTJ /D/ 04WIDTH,INSIDE,TUBE TUBE INSIDE WIDTH AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A TUBE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CBSWJ /D/ 04HEIGHT,INSIDE,TUBE TUBE INSIDE HEIGHT AN INSIDE MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE TUBE,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 CBSXJ /D/ 04DIAMETER,INSIDE,MINIMUM,TUBE TUBE MINIMUM INSIDE DIAMETER THE SMALLEST LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A TUBE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 1D AND 1B MODE REPLY11AA05 CBSYJ /D/ 04DIAMETER,INSIDE,MAXIMUM,TUBE TUBE MAXIMUM INSIDE DIAMETER THE LARGEST LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A TUBE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 1D AND 1B MODE REPLY11AA05 CBSZD /D/ 19FACILITY,ATTACHMENT/FASTENING,END END ATTACHMENT/FASTENING FACILITY AN INDICATION OF THE END ATTACHMENT/S/ AND/OR FASTENING FACILITY/IES/ PROVIDED. PLEASE USE MRC BBXW WITH ISAC CODING INPLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AC52 CBTBD /D/ 07FEATURE,ENAMELED ENAMELED FEATURE AN INDICATION OF WHETHER OR NOT AN ENAMELED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CBTCD 04SIZE,HANDLE,BATTERY BATTERY HANDLE SIZE DESIGNATES THE SIZE OF THE BATTERY HANDLE(S). SELECT REPLY CODE 10AF81 CBTDD /D/ 07AXIS,ASTIGMATISM FINDING ASTIGMATISM FINDING AXIS AN INDICATION OF WHETHER OR NOT AN AXIS FOR ASTIGMATISM FINDING IS PROVIDED. SELECT REPLY CODE 10AB22 CBTFD /D/ 07SCALE SCALE AN INDICATION OF WHETHER OR NOT A SCALE IS PROVIDED. SELECT REPLY CODE 10AB22 CBTGD /D/ 07RHEOSTAT,BUILT-IN BUILT-IN RHEOSTAT AN INDICATION OF WHETHER OR NOT A BUILT-IN RHEOSTAT IS PROVIDED. SELECT REPLY CODE 10AB22 CBTHJ /D/ 03DESIGNATOR,SIZE SIZE DESIGNATOR A DESIGNATION INDICATING THE SIZE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 2D AND 1B MODE REPLY21AF981AC20 CBTJD /D/ 02DESIGN,SLEEVE,ELECTRICAL/WATER CONNECTING ELECTRICAL/WATER CONNECTING SLEEVE DESIGN AN INDICATION OF WHETHER OR NOT THE ELECTRICAL AND/OR WATER CONNECTION SLEEVE PERMITS FREE ROTATION OF THE SHEATH. SELECT REPLY CODE 10AK54 CBTKD /D/ 07COMBINATION,CARRIER,TELESCOPE/LIGHT TELESCOPE/LIGHT CARRIER COMBINATION AN INDICATION OF WHETHER OR NOT A TELESCOPE AND LIGHT CARRIER COMBINATION IS PROVIDED. SELECT REPLY CODE 10AB22 CBTLD 18TYPE,VISION VISION TYPE INDICATES THE TYPE OF VISION PROVIDED BY THE CONSTRUCTION OF THE ITEM. SELECT REPLY CODE 10AF63 CBTMJ /D/ 04DIAMETER,OUTSIDE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AF98 CBTND /D/ 07FEATURE,PNEUMATIC PNEUMATIC FEATURE AN INDICATION OF WHETHER OR NOT A PNEUMATIC FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CBTPA 12QUANTITY,CARRIER,LAMP LAMP CARRIER QUANTITY THE NUMBER OF LAMP CARRIERS PROVIDED. 1A MODE REPLY 0 CBTQA 12QUANTITY,VENT,AIR AIR VENT QUANTITY THE NUMBER OF AIR VENTS PROVIDED. 1A MODE REPLY 0 CBTRD /D/ 07CARRIER,LIGHT LIGHT CARRIER AN INDICATION OF WHETHER OR NOT A LIGHT CARRIER(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CBTSA 03DESIGNATOR,SIZE,SHEATH SHEATH SIZE DESIGNATOR A DESIGNATION INDICATING THE SIZE BY WHICH THE SHEATH IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1A MODE REPLY 0 CBTTD /D/ 07OBTURATOR OBTURATOR AN INDICATION OF WHETHER OR NOT AN OBTURATOR(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CBTWD /D/ 02DESIGN,END,SHEATH DISTAL SHEATH DISTAL END DESIGN THE DESIGN OF THE SHEATH DISTAL END. SELECT REPLY CODE 10AK54 CBTXD /D/ 07ASSEMBLY,BRIDGE BRIDGE ASSEMBLY AN INDICATION OF WHETHER OR NOT A BRIDGE ASSEMBLY IS PROVIDED. SELECT REPLY CODE 10AB22 CBTYA 12QUANTITY,SPECULUM SPECULUM QUANTITY THE NUMBER OF SPECULUMS PROVIDED WITH THE ITEM. 1A MODE REPLY 0 CBTZA 12QUANTITY,TIP,EAR EAR TIP QUANTITY THE NUMBER OF EAR TIPS PROVIDED WITH THE ITEM. 1A MODE REPLY 0 CBWBD /D/ 07ATTACHMENT,INSUFFLATOR INSUFFLATOR ATTACHMENT AN INDICATION OF WHETHER OR NOT AN INSUFFLATOR ATTACHMENT IS PROVIDED. SELECT REPLY CODE 10AB22 CBWCJ 10CURRENT RATING,LAMP LAMP CURRENT RATING THE AMOUNT OF CURRENT FOR WHICH THE LAMP IS RATED. 1D AND 1B MODE REPLY11AC30 CBWDJ 04DIAMETER,OVERALL,MIRROR MIRROR OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF A MIRROR. 1D AND 1B MODE REPLY11AA05 CBWFD 07REMOVABILITY,MIRROR MIRROR REMOVABILITY AN INDICATION OF WHETHER OR NOT THE MIRROR IS REMOVABLE. SELECT REPLY CODE 10AC29 CBWGD 07VARIABILITY,PEEPHOLE PEEPHOLE VARIABILITY AN INDICATION OF WHETHER OR NOT THE PEEPHOLE IS VARIABLE. SELECT REPLY CODE 10AH65 CBWHA 12QUANTITY ACCOMMDATED,SLIDE SLIDE QUANTITY ACCOMMODATED THE NUMBER OF SLIDES THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 CBWJB 10POWER RATING IN DIOPTERS POWER RATING IN DIOPTERS THE RATED POWER OF THE ITEM,EXPRESSED IN DIOPTERS. 1B MODE REPLY 0 CBWKD /D/ 19DETERMINATION,VISUAL VISUAL DETERMINATION AN INDICATION OF THE VISUAL DETERMINATION/S/ PROVIDED. SELECT REPLY CODE 10AK54 CBWLD /D/ 07HANDLE,CORD CORD HANDLE AN INDICATION OF WHETHER OR NOT A CORD HANDLE(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CBWMD /D/ 07HANDLE,BATTERY BATTERY HANDLE AN INDICATION OF WHETHER OR NOT A BATTERY HANDLE(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CBWND /D/ 07STRAP,CHIN CHIN STRAP AN INDICATION OF WHETHER OR NOT A CHIN STRAP IS INCLUDED. SELECT REPLY CODE 10AA49 CBWPD /D/ 18TYPE,LINING,UPPER GARMENT UPPER GARMENT LINING TYPE INDICATES THE TYPE OF UPPER GARMENT LINING FURNISHED. SELECT REPLY CODE 10AK54 CBWQD /D/ 07BOLT BOLT AN INDICATION OF WHETHER OR NOT A BOLT IS INCLUDED. SELECT REPLY CODE 10AA49 CBWRD 18TYPE,COPY COPY TYPE INDICATES THE TYPE OF COPY PROVIDED. SELECT REPLY CODE 10AK54 CBWSA 12QUANTITY,PARTS PARTS QUANTITY THE NUMBER OF PARTS PROVIDED. 1A MODE REPLY 0 CBWTD 19PROCESS FOR WHICH DESIGNED PROCESS FOR WHICH DESIGNED THE PROCESS FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AH21 CBWWD 11METHOD,TRANSFER,MULTICOPY MULTICOPY TRANSFER METHOD THE MEANS OF TRANSFERRING COPY FOR MULTICOPY TYPE ITEMS. SELECT REPLY CODE 10AK54 CBWXD /D/ 07COATING,PREVENTIVE,SMEAR/STAIN SMEAR/STAIN PREVENTIVE COATING AN INDICATION OF WHETHER OR NOT A SMEAR AND/OR STAIN PREVENTIVE COATING IS PROVIDED. SELECT REPLY CODE 10AB22 CBWYD /D/ 07FEATURE,PRINTED PRINTED FEATURE AN INDICATION OF WHETHER OR NOT A PRINTED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CBWZD 08LOCATION,RULING RULING LOCATION INDICATES THE LOCATION OF THE RULING ON THE ITEM. SELECT REPLY CODE 10AJ91 CBXBD /D/ 07LINE,MARGINAL,VERTICAL VERTICAL MARGINAL LINE AN INDICATION OF WHETHER OR NOT A VERTICAL MARGINAL LINE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 CBXCA 12QUANTITY,LINE,VERTICAL RULED,LEFT-HAND PAGE LEFT-HAND PAGE VERTICAL RULED LINE QUANTITY THE NUMBER OF VERTICAL RULED LINES PROVIDED ON THE LEFT-HAND PAGE. 1A MODE REPLY 0 CBXDJ /D/A04SPACING,LINES,VERTICAL RULED,LEFT-HAND PAGE LEFT-HAND PAGE VERTICAL RULED LINES SPACING THE SPACING OF THE LEFT-HAND PAGE VERTICAL RULED LINES. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 1D AND 1A MODE REPLY13AJ40 CBXFA 12QUANTITY,LINE,VERTICAL RULED,RIGHT-HAND PAGE RIGHT-HAND PAGE VERTICAL RULED LINE QUANTITY THE NUMBER OF VERTICAL RULED LINES PROVIDED ON THE RIGHT-HAND PAGE. 1A MODE REPLY 0 CBXGJ /D/A04SPACING,LINES,VERTICAL RULED,RIGHT-HAND PAGE RIGHT-HAND PAGE VERTICAL RULED LINES SPACING THE SPACING OF THE RIGHT-HAND PAGE VERTICAL RULED LINES. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. 1D AND 1A MODE REPLY13AJ40 CBXHB 10PERCENTAGE PER PAGE,STOCK,RAG RAG STOCK PERCENTAGE PER PAGE THE PERCENTAGE OF RAG STOCK CONTAINED IN EACH PAGE. 1B MODE REPLY 0 CBXJA 12QUANTITY,PAGE PAGE QUANTITY THE NUMBER OF PAGES PROVIDED. 1A MODE REPLY 0 CBXKD /D/ 07PAGES,NUMBERED NUMBERED PAGES AN INDICATION OF WHETHER OR NOT NUMBERED PAGES ARE PROVIDED. IF PROVIDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AB22 CBXMD /D/ 07FEATURE,MOUNTING,MUSLIN MUSLIN MOUNTING FEATURE AN INDICATION OF WHETHER OR NOT A MUSLIN MOUNTING FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 CBXND 01COLOR,LINE LINE COLOR THE HUE OR TINT OF THE LINE. SELECT REPLY CODE 10AD06 CBXPD /D/ 07FEATURE,RULED,PEN PEN RULED FEATURE AN INDICATION OF WHETHER OR NOT A PEN RULED FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 CBXQG 19DIVISION,RULING RULING DIVISION THE RULING DIVISION OF THE ITEM. FULL TEXT WRITE-IN 0 CBXRJ B04SIZE,AREA,PRINTED PRINTED AREA SIZE DESIGNATES THE SIZE OF THE PRINTED AREA. 1D AND 1F MODE REPLY11AA05 CBXSG /D/ 19INSCRIPTION/DESIGN,ADDITIONAL ADDITIONAL INSCRIPTION/DESIGN AN INDICATION OF ANY ADDITIONAL LETTERING OR TYPE OF DESIGN ON THE ITEM. FULL TEXT WRITE-IN 0 CBXTD /D/ 07HOLE,PUNCHED PUNCHED HOLE AN INDICATION OF WHETHER OR NOT A PUNCHED HOLE/S/ IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 CBXWD /D/ 07FOLD,FLAT,CONTINUOUS CONTINUOUS FLAT FOLD AN INDICATION OF WHETHER OR NOT A CONTINUOUS FLAT FOLD IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 CBXXJ 04LENGTH,FOLD FOLD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A FOLD,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBXYD 08LOCATION,PUNCH,FILING FILING PUNCH LOCATION INDICATES THE LOCATION OF THE FILING PUNCH. SELECT REPLY CODE 10AJ91 CBXZD 18TYPE,SIZING SIZING TYPE INDICATES THE TYPE OF SIZING PROVIDED. SELECT REPLY CODE 10AK54 CBYBD /D/ 07FEED,SPROCKET SPROCKET FEED AN INDICATION OF WHETHER OR NOT A SPROCKET FEED IS INCLUDED. SELECT REPLY CODE 10AA49 CBYCJ 04DIAMETER,HOLE,SPROCKET SPROCKET HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SPROCKET HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBYDJ 04WIDTH,FOLD FOLD WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A FOLD,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CBYFJ /D/ 10INTERVAL,FOLDING FOLDING INTERVAL THE DISTANCE BETWEEN FOLDS. 2D AND 1B MODE REPLY21AA051AC20 CBYGJ 04LENGTH,FORM,FOLDED FOLDED FORM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FOLDED FORM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBYHJ 04LENGTH,FORM,ROLL ROLL FORM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ROLL FORM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBYJJ 04LENGTH,SIDE,BINDING BINDING SIDE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BINDING SIDE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBYKD /D/ 07EDGE,CLEAN CLEAN EDGE AN INDICATION OF WHETHER OR NOT A CLEAN EDGE IS INCLUDED. SELECT REPLY CODE 10AA49 CBYLD /D/ 18TYPE FOR WHICH DESIGNED,BINDER BINDER TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF BINDER FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 CBYMA /D/ 12QUANTITY PER PAD/BLOCK,SHEET SHEET QUANTITY PER PAD/BLOCK THE NUMBER OF SHEETS CONTAINED IN EACH PAD AND/OR BLOCK. PLEASE USE MRC CJXL IN PLACE OF THIS CANCELED MRC. 1A MODE REPLY 0 CBYND /D/ 09MATERIAL,LEG,LOWER BEAM LOWER BEAM LEG MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LOWER BEAM LEG IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBYPD /D/ 07LEG,LIFTING LIFTING LEG AN INDICATION OF WHETHER OR NOT A LIFTING LEG IS INCLUDED. SELECT REPLY CODE 10AA49 CBYQJ 04LENGTH,LEG,LIFTING LIFTING LEG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE LIFTING LEG,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CBYRD /D/ 09MATERIAL,LEG,LIFTING LIFTING LEG MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LIFTING LEG IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CBYSA 12QUANTITY,PENDANT,SPAN SPAN PENDANT QUANTITY THE NUMBER OF SPAN PENDANTS PROVIDED. 1A MODE REPLY 0 CBYTD /D/ 07FEATURE,NONMAGNETIC NONMAGNETIC FEATURE AN INDICATION OF WHETHER OR NOT A NONMAGNETIC FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CBYWJ 04DIAMETER ACCOMMODATED,ROPE,WIRE WIRE ROPE DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE WIRE ROPE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBYXD 05DIRECTION,LAY,ACCOMMODATED WIRE ROPE ACCOMMODATED WIRE ROPE LAY DIRECTION THE LAY DIRECTION OF THE WIRE ROPE ACCOMMODATED BY THE ITEM. SELECT REPLY CODE 10AA38 CBYYJ 04DIAMETER,OUTSIDE,LARGEST,SLEEVE SLEEVE LARGEST OUTSIDE DIAMETER THE LARGEST LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SLEEVE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBYZJ 04DIAMETER,INSIDE,LARGEST,SLEEVE SLEEVE LARGEST INSIDE DIAMETER THE LARGEST LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SLEEVE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBZBJ /D/ 04TAPER PER FOOT,SLEEVE SLEEVE TAPER PER FOOT THE AMOUNT OF TAPER OF THE SLEEVE,EXPRESSED AS A UNIT OF MEASURE PER FOOT. 1D AND 1B MODE REPLY12AG67 CBZCJ 04DIAMETER,OUTSIDE,GRIP LARGEST FREE GRIP LARGEST FREE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE LARGEST FREE CENTER OF THE GRIP,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBZDJ /D/ 04TAPER PER FOOT,GRIP GRIP TAPER PER FOOT THE AMOUNT OF TAPER OF THE GRIP,EXPRESSED AS A UNIT OF MEASURE PER FOOT. 1D AND 1B MODE REPLY12AG67 CBZFJ 04DIAMETER,INSIDE,GRIP GRIP INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A GRIP,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBZGD 14SHAPE,HOUSING HOUSING SHAPE THE PHYSICAL CONFIGURATION OF THE HOUSING. SELECT REPLY CODE 10AD07 CBZHJ /D/ 04HEIGHT,END,NOSE NOSE END HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A NOSE END,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CBZJJ /D/ 04RADIUS,SWIVEL SWIVEL RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CBZKJ /D/ 04HEIGHT,END,TAIL TAIL END HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A TAIL END,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CBZLJ /D/ 04DIAMETER,END,TAIL TAIL END DIAMETER THE LENGTH OF STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR TAIL END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBZMD 13THREAD SERIES DESIGNATOR,STEM STEM THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF STEM THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CBZNA 13THREAD QUANTITY PER INCH,STEM STEM THREAD QUANTITY PER INCH A MEASUREMENT OF THE NUMBER OF THREADS ON THE STEM PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE AXIS. 1A MODE REPLY 0 CBZPJ 04THREAD DIAMETER,STEM STEM THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF A STEM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CBZQJ 03DESIGNATOR,SIZE,NOMINAL PIPE,STEM STEM NOMINAL PIPE SIZE DESIGNATOR THE INDUSTRIAL SIZE DESIGNATION USED TO INDICATE THE DIAMETER OF THE STEM PIPE. 1D AND 1B MODE REPLY11AA05 CBZRL 16STYLE,SOCKET,STEM STEM SOCKET STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE STEM SOCKET. 1L MODE REPLY 0 CBZSJ 03DESIGNATOR,SIZE,NOMINAL PIPE,STEM SOCKET STEM SOCKET NOMINAL PIPE SIZE DESIGNATOR THE INDUSTRIAL SIZE DESIGNATION USED TO INDICATE THE DIAMETER OF THE STEM SOCKET PIPE. 1D AND 1B MODE REPLY11AA05 CBZTL 16STYLE,PLATE PLATE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PLATE. 1L MODE REPLY 0 CBZWJ 04WIDTH,BULGE BULGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CBZXJ 04LENGTH,ARM,FIRST FIRST ARM LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CBZYJ 04LENGTH,ARM,SECOND SECOND ARM LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CBZZD 18TYPE,BEARING,WHEEL WHEEL BEARING TYPE INDICATES THE TYPE OF WHEEL BEARING(S) PROVIDED. SELECT REPLY CODE 10AH96 CCBBD 18TYPE,BEARING,SWIVEL SWIVEL BEARING TYPE INDICATES THE TYPE OF SWIVEL BEARING(S) PROVIDED. SELECT REPLY CODE 10AH96 CCBCD 19ARRANGEMENT,BEARING,SWIVEL SWIVEL BEARING ARRANGEMENT THE ARRANGEMENT OF THE SWIVEL BEARING(S) IN OR ON THE ITEM. SELECT REPLY CODE 10AH86 CCBDD 18TYPE,BEARING,KING BOLT KING BOLT BEARING TYPE INDICATES THE TYPE OF KING BOLT BEARING PROVIDED. SELECT REPLY CODE 10AH96 CCBGD /D/ 07CAPABILITY,DISASSEMBLY DISASSEMBLY CAPABILITY AN INDICATION OF WHETHER OR NOT A DISASSEMBLY CAPABILITY IS PROVIDED. SELECT REPLY CODE 10AB22 CCBHJ 04WIDTH,TREAD TREAD WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TREAD,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CCBJJ /D/ 04WIDTH,STEM STEM WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCBKJ 04DIAMETER,HOLE,STEM MOUNTING STEM MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CCBLA /D/ 12QUANTITY,HOLE,STEM MOUNTING STEM MOUNTING HOLE QUANTITY NONE. 1A MODE REPLY 0 CCBMJ 04DISTANCE BETWEEN HOLES ALONG STEM,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG STEM NONE. 2D AND 1B MODE REPLY21AA051AC20 CCBND /D/ 07CONTACT,ROTATING ROTATING CONTACT AN INDICATION OF WHETHER OR NOT A ROTATING CONTACT(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCBPD /D/ 03DESIGNATION,DESIGN,TELESCOPE TELESCOPE DESIGN DESIGNATION THE DESIGNATION DERIVED FROM THE NAME OF THE DESIGNER BY WHICH THE TELESCOPE IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. SELECT REPLY CODE 10AJ50 CCBQD /D/ 03DESIGNATION,DESIGN,EVACUATION EVACUATION DESIGN DESIGNATION THE DESIGNATION DERIVED FROM THE NAME OF THE DESIGNER BY WHICH THE EVACUATOR IS COMMERICALLY KNOWN AND/OR IDENTIFIED. SELECT REPLY CODE 10AJ50 CCBRD 18TYPE,RADIATION,ULTRAVIOLET ULTRAVIOLET RADIATION TYPE INDICATES THE TYPE OF ULTRAVIOLET RADIATION REQUIRED FOR OPERATION OF THE ITEM. SELECT REPLY CODE 10AD48 CCBSJ 04LENGTH,CABINET CABINET LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CABINET,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CCBTJ 04WIDTH,CABINET CABINET WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A CABINET,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CCBWJ 04DEPTH,CABINET CABINET DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON A CABINET,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CCBXD /D/ 07PLATE,CONTROL,CABINET PANEL CABINET PANEL CONTROL PLATE AN INDICATION OF WHETHER OR NOT A CABINET PANEL CONTROL PLATE(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCBYD /D/ 07REST,CHIN,CABINET CABINET CHIN REST AN INDICATION OF WHETHER OR NOT A CABINET CHIN REST/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 CCBZD 18TYPE,RECEPTACLE,CABINET CABINET RECEPTACLE TYPE INDICATES THE TYPE OF CABINET RECEPTACLE PROVIDED. SELECT REPLY CODE 10AM39 CCCBD /D/ 07STAND,MOUNTING MOUNTING STAND AN INDICATION OF WHETHER OR NOT A MOUNTING STAND(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCCCJ /D/ 04DIAMETER,OUTSIDE,CANNULA CANNULA OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CANNULA,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. PLEASE USE MRC ABHE WITH ISAC TABLE 0230 IN PLACE OF THIS CANCELED MRC. 2D AND 1B MODE REPLY21AF981AC20 CCCDJ /D/ 04LENGTH,REPOSITOR REPOSITOR LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE REPOSITOR,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CCCFD /D/ 07ATTACHMENT,IRRIGATING,REPLACEMENT REPLACEMENT IRRIGATING ATTACHMENT AN INDICATION OF WHETHER OR NOT A REPLACEMENT IRRIGATING ATTACHMENT IS PROVIDED. SELECT REPLY CODE 10AB22 CCCGD /D/ 03DESIGNATION,SIZE,HANDLE HANDLE SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE HANDLE IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. SELECT REPLY CODE 10AF81 CCCHD /D/ 07FEATURE,TIP,DOUBLE DOUBLE TIP FEATURE AN INDICATION OF WHETHER OR NOT A DOUBLE TIP FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CCCJD /D/ 18TYPE,SECTION,FORE FORE SECTION TYPE INDICATES THE TYPE OF FORE SECTION PROVIDED. SELECT REPLY CODE 10AK54 CCCKD /D/ 07EYE EYE AN INDICATION OF WHETHER OR NOT AN EYE(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCCLD /D/ 07SHIELD,POINT POINT SHIELD AN INDICATION OF WHETHER OR NOT A POINT SHIELD(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCCMD /D/ 07PROBE,WIRE WIRE PROBE AN INDICATION OF WHETHER OR NOT A WIRE PROBE(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCCND /D/ 07FEATURE,SHOTTED SHOTTED FEATURE AN INDICATION OF WHETHER OR NOT A SHOTTED FEATURE/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 CCCPD /D/ 07FEATURE,JOINTED JOINTED FEATURE AN INDICATION OF WHETHER OR NOT A JOINTED FEATURE/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 CCCQD /D/ 07CONNECTION,SCREW,HANDLE REVERSIBLE HANDLE REVERSIBLE SCREW CONNECTION AN INDICATION OF WHETHER OR NOT A HANDLE REVERSIBLE SCREW CONNECTION/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 CCCRD /D/ 07DETACHABILITY,POINT,WORKING WORKING POINT DETACHABILITY AN INDICATION OF WHETHER OR NOT THE WORKING POINT/S/ IS DETACHABLE. SELECT REPLY CODE 10AH97 CCCSA /D/ 12QUANTITY,SPRING SPRING QUANTITY THE NUMBER OF SPRINGS PROVIDED. 1A MODE REPLY 0 CCCTD /D/ 07RACK,POINT POINT RACK AN INDICATION OF WHETHER OR NOT A POINT RACK(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCCWA /D/ 12QUANTITY,STEP,ADJUSTMENT ADJUSTMENT STEP QUANTITY THE NUMBER OF ADJUSTMENT STEPS PROVIDED. 1A MODE REPLY 0 CCCXD 03DESIGNATION,DESIGN,CHUCK CHUCK DESIGN DESIGNATION THE DESIGNATION DERIVED FROM THE NAME OF THE DESIGNER BY WHICH THE CHUCK IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. SELECT REPLY CODE 10AJ50 CCCYD 11METHOD,ATTACHMENT,INSTRUMENT INSTRUMENT ATTACHMENT METHOD THE MEANS BY WHICH THE INSTRUMENT IS ATTACHED TO THE ITEM. SELECT REPLY CODE 10AB47 CCCZJ /D/ 04DISTANCE,TESTING TESTING DISTANCE THE DISTANCE THE ITEM IS DESIGNED TO TEST. 1D AND 1B MODE REPLY11AA05 CCDBD 07ADJUSTABILITY,ARM ARM ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE ARM(S) IS ADJUSTABLE. SELECT REPLY CODE 10AB00 CCDCA 12QUANTITY ACCOMMODATED,BATTERY BATTERY QUANTITY ACCOMMODATED THE NUMBER OF BATTERIES THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 CCDDD 07RECHARGEABILITY RECHARGEABILITY AN INDICATION OF WHETHER OR NOT THE ITEM IS RECHARGEABLE. SELECT REPLY CODE 10AK95 CCDFD /D/ 02DESIGN,SPRING SPRING DESIGN THE DESIGN OF THE SPRING(S). SELECT REPLY CODE 10AK54 CCDGJ 04WIDTH ACROSS FLATS,OVERALL OVERALL WIDTH ACROSS FLATS THE OVERALL MEASUREMENT FROM ONE FLATTED SURFACE TO THE OPPOSITE FLATTED SURFACE. 2D AND 1B MODE REPLY21AA051AC20 CCDHJ 04LENGTH ACCOMMODATED,SHANK,ELECTRODE ELECTRODE SHANK LENGTH ACCOMMODATED A MEASUREMENT OF THE LONGEST DIMENSION OF THE ELECTRODE SHANK THAT THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CCDJJ 04DIAMETER ACCOMMODATED,SHANK,ELECTRODE ELECTRODE SHANK DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE ELECTRODE SHANK,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CCDKJ 04DISTANCE ACCOMMODATED,CENTER TO CENTER,SHANK,ELECTRODE ELECTRODE SHANK CENTER TO CENTER DISTANCE ACCOMMODATED THE CENTER TO CENTER DISTANCE OF THE ELECTRODE SHANK THAT THE ITEM IS DESIGNED TO ACCOMMODATE. 2D AND 1B MODE REPLY21AA051AC20 CCDLJ 04DIAMETER,OUTSIDE,GRIP GRIP OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GRIP,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CCDMD /D/ 07END TO ACCOMMODATE PLUGGER POINTS,THREADED THREADED END TO ACCOMMODATE PLUGGER POINTS AN INDICATION OF WHETHER OR NOT A THREADED END/S/ TO ACCOMMODATE PLUGGER POINTS IS PROVIDED. SELECT REPLY CODE 10AB22 CCDND 11METHOD,VARIATION,DELAY TIME DELAY TIME VARIATION METHOD THE MEANS USED TO VARY THE DELAY TIME OF THE ITEM. SELECT REPLY CODE 10AD63 CCDPJ 10TIME PER STEP,DELAY DELAY TIME PER STEP THE AMOUNT OF TIME DELAY BETWEEN ADJACENT STEP SETTINGS. 2D AND 1B MODE REPLY22AB491AC20 CCDQJ 10TIME,DELAY,SECTION SECTION DELAY TIME THE TIME DELAY OF EACH SECTION OF AN ITEM. 3D AND 1B MODE REPLY32AB491AC202AH19 CCDRJ A12QUANTITY PER SECTION,SEGMENT SEGMENT QUANTITY PER SECTION THE NUMBER OF SEGMENTS INTO WHICH A SECTION IS DIVIDED. 1D AND 1A MODE REPLY12AH19 CCDSJ 10TIME,DELAY,SEGMENT SEGMENT DELAY TIME THE TIME DELAY OF EACH SEGMENT. 4D AND 1B MODE REPLY42AB491AC202AH192AD80 CCDTJ 10VARIATION PER DEG CELSIUS,TIME,DELAY DELAY TIME VARIATION PER DEG CELSIUS THE CHANGE IN DELAY AS A RESULT OF THE TEMPERATURE CHANGE PER DEGREE CELSIUS. 1D AND 1B MODE REPLY12AB49 CCDXJ 10TIME RATING,RISE,PULSE PULSE RISE TIME RATING THE RATED TIME REQUIRED FOR THE PULSE TO RISE. 1D AND 1B MODE REPLY12AB49 CCDYJ /D/ 04WIDTH,KNOB KNOB WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCDZJ /D/ 04DEPTH,BRACKET BRACKET DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCFBJ 04DISTANCE FROM FLANGE TO BOTTOM OF BODY DISTANCE FROM FLANGE TO BOTTOM OF BODY NONE. 2D AND 1B MODE REPLY21AA051AC20 CCFCJ 04DISTANCE FROM END OF BODY TO CENTER OF SHAFT DISTANCE FROM END OF BODY TO CENTER OF SHAFT NONE. 2D AND 1B MODE REPLY21AA051AC20 CCFDJ 04DISTANCE FROM BOTTOM OF BODY TO CENTER OF SHAFT DISTANCE FROM BOTTOM OF BODY TO CENTER OF SHAFT NONE. 2D AND 1B MODE REPLY21AA051AC20 CCFFJ /D/A18TYPE AND QUANTITY,TERMINAL TERMINAL TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION. PLEASE USE MRC TTQY IN PLACE OF THIS CANCELED MRC. 1D AND 1A MODE REPLY14AA58 CCFGJ 04SIZE,VALVE VALVE SIZE DESIGNATES THE SIZE OF THE VALVE. 1D AND 1B MODE REPLY11AA05 CCFHG /D/ 10FLOW RATE AND FLUID TYPE FLOW RATE AND FLUID TYPE THE AMOUNT OF FLOW PER UNIT OF MEASURE,AND TYPE OF FLUID FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 CCFJJ 04DEPTH,COUNTERBORE,SECOND SECOND COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCFKG /D/ 04SIZE FOR WHICH DESIGNED,HOSE/TUBE HOSE/TUBE SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF HOSE OR TUBE FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 CCFLJ 13THREAD DIAMETER,PIPE,NOMINAL,CONNECTING END CONNECTING END NOMINAL PIPE THREAD DIAMETER THE NOMINAL PIPE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE CONNECTING END,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CCFMD /D/ 07FEATURE,CHANGE,AUTOMATIC,REVERSE FLOW PORT AREA REVERSE FLOW PORT AREA AUTOMATIC CHANGE FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE IS INCLUDED FOR PERMITTING THE PORT AREA TO BE AUTOMATICALLY CHANGED WHEN FLOW IS REVERSED. SELECT REPLY CODE 10AA49 CCFND 18TYPE,SCREEN SCREEN TYPE INDICATES THE TYPE OF SCREEN PROVIDED. SELECT REPLY CODE 10AC48 CCFPD /D/ 07REMOVABILITY,SCREEN SCREEN REMOVABILITY AN INDICATION OF WHETHER OR NOT THE SCREEN IS REMOVABLE. SELECT REPLY CODE 10AC29 CCFQG /D/ 10RATIO OF OPEN SCREEN AREA TO INLET AREA RATIO OF OPEN SCREEN AREA TO INLET AREA THE INDICATED RATIO BETWEEN OPEN SCREEN AREA TO INLET AREA. FULL TEXT WRITE-IN 0 CCFRD /D/ 07MAGNET MAGNET AN INDICATION OF WHETHER OR NOT A MAGNET(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CCFSJ 04DIAMETER,INSIDE,INLET FLANGE INLET FLANGE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INLET FLANGE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CCFTJ /D/ 04DIAMETER,CIRCLE,BOLT,INLET FLANGE INLET FLANGE BOLT CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT CIRCLE ON THE INLET FLANGE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CCFWG /D/ 04SPACING,HOLE,INLET FLANGE MOUNTING INLET FLANGE MOUNTING HOLE SPACING THE SPACING OF THE MOUNTING HOLES ON THE INLET FLANGE. FULL TEXT WRITE-IN 0 CCFXD /D/ 07PROVISION,THREAD,INLET FLANGE MOUNTING HOLE INLET FLANGE MOUNTING HOLE THREAD PROVISION AN INDICATION OF WHETHER OR NOT THE MOUNTING HOLE/S/ ON THE INLET FLANGE IS THREADED. SELECT REPLY CODE 10AE00 CCFZD /D/ 13THREAD SERIES,HOLE,INLET MOUNTING INLET MOUNTING HOLE THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF AN INLET MOUNTING HOLE. SELECT REPLY CODE 10AH06 CCGBD /D/ 13THREAD DIRECTION,HOLE,INLET MOUNTING INLET MOUNTING HOLE THREAD DIRECTION THE DIRECTION OF THE INLET MOUNTING HOLE THREAD WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AA38 CCGCD /D/ 07FITTING,INLET INLET FITTING AN INDICATION OF WHETHER OR NOT AN INLET FITTING IS INCLUDED. SELECT REPLY CODE 10AA49 CCGDA /D/ 13THREAD SIZE,FITTING,INLET INLET FITTING THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED INLET FITTING. 1A MODE REPLY 0 CCGFD /D/ 13THREAD SERIES,FITTING,INLET INLET FITTING THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF AN INLET FITTING. SELECT REPLY CODE 10AH06 CCGGD 13THREAD DIRECTION,FITTING,INLET INLET FITTING THREAD DIRECTION THE DIRECTION OF THE INLET FITTING THREAD WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AA38 CCGHD /D/ 13THREAD LOCATION,FITTING,INLET INLET FITTING THREAD LOCATION INDICATES THE LOCATION OF THE THREADED PORTION OF THE INLET FITTING. SELECT REPLY CODE 10AJ91 CCGKJ 04DIAMETER,INSIDE,OUTLET FLANGE OUTLET FLANGE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTLET FLANGE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CCGLA /D/ 12QUANTITY,HOLE,OUTLET FLANGE MOUNTING OUTLET FLANGE MOUNTING HOLE QUANTITY THE NUMBER OF OUTLET FLANGE MOUNTING HOLES PROVIDED. 1A MODE REPLY 0 CCGMJ /D/ 04DIAMETER,CIRCLE,BOLT,OUTLET FLANGE OUTLET FLANGE BOLT CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTLET FLANGE CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CCGNG /D/ 11METHOD,SECURING,TUBE TUBE SECURING METHOD THE MEANS BY WHICH THE TUBE IS SECURED. FULL TEXT WRITE-IN 0 CCGPD /D/ 07GLASS TO DESICCATOR JAR,GROUND GROUND GLASS TO DESICCATOR JAR AN INDICATION OF WHETHER OR NOT GROUND GLASS TO DESICCATOR JAR IS PROVIDED. SELECT REPLY CODE 10AB22 CCGQD /D/ 09MATERIAL,JAR,DESICCATOR DESICCATOR JAR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE DESICCATOR JAR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCGRD /D/ 07BLOCK,COOLING COOLING BLOCK AN INDICATION OF WHETHER OR NOT A COOLING BLOCK IS PROVIDED. SELECT REPLY CODE 10AB22 CCGSD 18TYPE,FLUE FLUE TYPE INDICATES THE TYPE OF FLUE PROVIDED. SELECT REPLY CODE 10AK54 CCGTD /D/ 09MATERIAL,FLUE FLUE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FLUE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCGWD /D/ 07SUPPORT,GLASSWARE,WIRE WIRE GLASSWARE SUPPORT AN INDICATION OF WHETHER OR NOT A WIRE GLASSWARE SUPPORT IS PROVIDED. SELECT REPLY CODE 10AB22 CCGXD /D/ 07GLASSWARE GLASSWARE AN INDICATION OF WHETHER OR NOT GLASSWARE IS PROVIDED. SELECT REPLY CODE 10AB22 CCGYD /D/ 07TUBING TUBING AN INDICATION OF WHETHER OR NOT TUBING IS PROVIDED. SELECT REPLY CODE 10AB22 CCGZD /D/ 07PUMP,SUCTION SUCTION PUMP AN INDICATION OF WHETHER OR NOT A SUCTION PUMP IS PROVIDED. SELECT REPLY CODE 10AB22 CCHBJ /D/T10RANGE,GAGE,PRESSURE PRESSURE GAGE RANGE THE MINIMUM TO MAXIMUM PRESSURE AT WHICH THE PRESSURE GAGE WILL OPERATE. 1D AND 1F MODE REPLY12AG20 CCHCD 07ADJUSTABILITY,ANGLE,INCLINATION INCLINATION ANGLE ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE INCLINATION ANGLE IS ADJUSTABLE. SELECT REPLY CODE 10AB00 CCHDD /D/ 18TYPE,MIRROR MIRROR TYPE INDICATES THE TYPE OF MIRROR PROVIDED. SELECT REPLY CODE 10AK54 CCHFD /D/ 07MATERIAL DIFFERENT FROM BASIC MATERIAL,PARTS PARTS MATERIAL DIFFERENT FROM BASIC MATERIAL AN INDICATION OF WHETHER OR NOT THE PARTS MATERIAL IS DIFFERENT FROM THE BASIC MATERIAL. SELECT REPLY CODE 10AB00 CCHGD /D/ 09MATERIAL,LINING,PARTIAL PARTIAL LINING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PARTIAL LINING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCHHD /D/ 08LOCATION,LINING,PARTIAL PARTIAL LINING LOCATION INDICATES THE LOCATION OF THE PARTIAL LINING PORTION OF AN ITEM. SELECT REPLY CODE 10AJ91 CCHJD /D/ 09MATERIAL,LINING,HAND HAND LINING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HAND LINING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCHKD /D/ 09MATERIAL,LINING,GAUNTLET GAUNTLET LINING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE GAUNTLET LINING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCHLD /D/ 09MATERIAL,PALM,SHELL SHELL PALM MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHELL PALM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCHMD /D/ 09MATERIAL,GAUNTLET,SHELL SHELL GAUNTLET MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHELL GAUNTLET IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCHND /D/ 18TYPE,CLOSURE,SHELL SHELL CLOSURE TYPE INDICATES THE TYPE OF SHELL CLOSURE PROVIDED. SELECT REPLY CODE 10AK54 CCHPD /D/ 11METHOD,ATTACHMENT,BIB TO CAPE BIB TO CAPE ATTACHMENT METHOD THE MEANS USED TO ATTACH THE BIB TO THE CAPE. SELECT REPLY CODE 10AM39 CCHQD /D/ 09MATERIAL,PANELS/BINDING PANELS/BINDING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PANELS AND BINDING ARE FABRICATED. SELECT REPLY CODE 10AD09 CCHRD /D/ 01COLOR,PANELS/BINDING PANELS/BINDING COLOR THE HUE OR TINT OF THE PANELS AND/OR BINDING. SELECT REPLY CODE 10AD06 CCHSA /D/ 19IDENTIFICATION,SHADE,PANELS/BINDING PANELS/BINDING SHADE IDENTIFICATION A DESIGNATION ASSIGNED TO A PARTICULAR GRADATION OF THE PANELS AND/OR BINDING COLOR FOR PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 CCHTD /D/ 09MATERIAL,BACK,SHELL SHELL BACK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHELL BACK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCHWD /D/ 19SOURCE,SHADE,PANELS/BINDING PANELS/BINDING SHADE SOURCE THE NAME OF THE REFERENCE SOURCE OF THE PANELS AND/OR BINDING SHADE IDENTIFICATION DESIGNATOR. SELECT REPLY CODE 10AF94 CCHXD /D/ 09MATERIAL,INTERIOR INTERIOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INTERIOR IS FABRICATED. SELECT REPLY CODE 10AD09 CCHYD 18TYPE,MOUNTING,MAGNIFIER MAGNIFIER MOUNTING TYPE INDICATES THE TYPE OF MOUNT USED TO SUPPORT THE MAGNIFIER. SELECT REPLY CODE 10AA78 CCHZD /D/ 11METHOD,SUPPORT,DISH DISH SUPPORT METHOD THE MEANS PROVIDED FOR SUPPORTING THE DISH. SELECT REPLY CODE 10AH72 CCJBJ 04DIAMETER,OVERALL,LENS,MAGNIFIER MAGNIFIER LENS OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE CROSS-SECTIONAL PLANE OF THE MAGNIFIER LENS. 1D AND 1B MODE REPLY11AA05 CCJCJ 04DIAMETER,OVERALL,APERTURE,PLATE PLATE APERTURE OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE CROSS-SECTIONAL PLANE OF THE PLATE APERTURE. 1D AND 1B MODE REPLY11AA05 CCJDJ /D/ 04DIAMETER,OUTSIDE,CONDENSER TUBE INLET CONDENSER TUBE INLET OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CCJFJ /D/ 04DIAMETER,OUTSIDE,CONDENSER TUBE OUTLET CONDENSER TUBE OUTLET OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CCJGG /D/ 04SIZE,TAPER,STANDARD,CONDENSER TUBE VACUUM CONDENSER TUBE VACUUM STANDARD TAPER SIZE NONE. FULL TEXT WRITE-IN 0 CCJHJ /D/ 04DIAMETER,OUTSIDE,CONDENSER TUBE CONDENSER TUBE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CONDENSER TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CCJJJ /D/ 10VOLUME,INTERNAL INTERNAL VOLUME THE UNIT OF VOLUME FOR WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY12AG67 CCJKG 11METHOD,GENERATION,HYDROGEN HYDROGEN GENERATION METHOD THE CHARGE USED OR PROCESS EMPLOYED IN THE GENERATION OF HYDROGEN. FULL TEXT WRITE-IN 0 CCJLJ 04LENGTH,OVERALL,CYLINDER BODY CYLINDER BODY OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CYLINDER BODY. 2D AND 1B MODE REPLY21AA051AC20 CCJMJ 04DIAMETER,OVERALL,BODY,CYLINDER CYLINDER BODY OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE CROSS-SECTIONAL PLANE OF THE CYLINDER BODY. 2D AND 1B MODE REPLY21AA051AC20 CCJNJ /D/ 04LENGTH ACCOMMODATED,MAXIMUM,NAIL NAIL MAXIMUM LENGTH ACCOMMODATED THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF A NAIL THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CCJPJ 04DIAMETER ACCOMMODATED,DRILL,MAXIMUM MAXIMUM DRILL DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE DRILL,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CCJQD /D/ 07LOCK,GEAR GEAR LOCK AN INDICATION OF WHETHER OR NOT A GEAR LOCK(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCJRD 19SPACING,HOLE HOLE SPACING THE HOLE SPACING OF THE ITEM. SELECT REPLY CODE 10AM06 CCJSL 16STYLE,END,BLADE DRIVE BLADE DRIVE END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BLADE DRIVE END. 1L MODE REPLY 0 CCJTD 18TYPE,HOLDER,SCREW SCREW HOLDER TYPE INDICATES THE TYPE OF SCREW HOLDER(S) PROVIDED. SELECT REPLY CODE 10AK54 CCJWD /D/ 07FINISH,FACE FACE FINISH AN INDICATION OF WHETHER OR NOT A FACE FINISH IS PROVIDED. SELECT REPLY CODE 10AB22 CCJXA 12QUANTITY,END,BEVELED BEVELED END QUANTITY THE NUMBER OF ENDS THAT ARE BEVELED. 1A MODE REPLY 0 CCJYD /D/ 08LOCATION,HOOK,HANDLE HANDLE HOOK LOCATION INDICATES THE LOCATION OF THE HANDLE HOOK(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 CCJZD /D/ 07BRUSH/NEEDLE BRUSH/NEEDLE AN INDICATION OF WHETHER OR NOT A BRUSH AND NEEDLE ARE PROVIDED. SELECT REPLY CODE 10AB22 CCKBD /D/ 07HANDLE,RULED RULED HANDLE AN INDICATION OF WHETHER OR NOT A RULED HANDLE(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCKCD /D/ 07SUPPORT,SPLINT SPLINT SUPPORT AN INDICATION OF WHETHER OR NOT A SPLINT SUPPORT(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCKDD 14SHAPE,SECTION SECTION SHAPE THE PHYSICAL CONFIGURATION OF THE SECTION(S). SELECT REPLY CODE 10AD07 CCKFD /D/ 07SECTION,HINGED HINGED SECTION AN INDICATION OF WHETHER OR NOT A HINGED SECTION(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCKGD /D/ 07BAND,RED RED BAND AN INDICATION OF WHETHER OR NOT A RED BAND(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCKHD /D/ 19SECTION,ADJUSTMENT,ANGULAR ANGULAR ADJUSTMENT SECTION AN INDICATION OF THE SECTION/S/ THAT IS PROVIDED WITH ANGULAR ADJUSTMENT. SELECT REPLY CODE 10AJ91 CCKJD /D/ 07FEATURE,ANGULATION,ACUTE ACUTE ANGULATION FEATURE AN INDICATION OF WHETHER OR NOT AN ACUTE ANGULATION FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CCKKJ /D/ 04DIAMETER,LOOP,FOOT FOOT LOOP DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FOOT LOOP,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CCKLJ 04LENGTH,STRAP,RETENTION RETENTION STRAP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A RETENTION STRAP,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CCKMJ /D/ 04LENGTH,STRAP,HEEL HEEL STRAP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A HEEL STRAP,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CCKNJ /D/ 04LENGTH,STRAP,TRACTION TRACTION STRAP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A TRACTION STRAP,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CCKPJ /D/ 04LENGTH,INSTEP INSTEP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE INSTEP,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CCKQA /D/ 12QUANTITY,CROSSPIECE CROSSPIECE QUANTITY THE NUMBER OF CROSSPIECES PROVIDED. 1A MODE REPLY 0 CCKRJ /D/ 04SPACING,CROSSPIECE CROSSPIECE SPACING THE SPACING BETWEEN THE CROSSPIECES. 1D AND 1B MODE REPLY11AA05 CCKSJ A12QUANTITY PER UNIT OF MEASURE,HOOK HOOK QUANTITY PER UNIT OF MEASURE THE NUMBER OF HOOKS PER SPECIFIC UNIT OF MEASURE. 1D AND 1A MODE REPLY11AB39 CCKTA /D/ 12QUANTITY,ARM,ATTACHMENT ROD ATTACHMENT ROD ARM QUANTITY THE NUMBER OF ATTACHMENT ROD ARMS PROVIDED. 1A MODE REPLY 0 CCKWJ /D/ 04LENGTH,ARM,ATTACHMENT ROD ATTACHMENT ROD ARM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ATTACHMENT ROD ARM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CCKXJ 04DIAMETER,END,HANDLE HANDLE END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HANDLE END,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CCKYJ 04DIAMETER,END,TIP TIP END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A TIP END,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CCKZD /D/ 07CRUTCH CRUTCH AN INDICATION OF WHETHER OR NOT A CRUTCH(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCLBD /D/ 07SUPPORT/FOOTREST,SPLINT,ONE-PIECE ONE-PIECE SPLINT SUPPORT/FOOTREST AN INDICATION OF WHETHER OR NOT A ONE-PIECE SPLINT SUPPORT AND FOOTREST ARE PROVIDED. SELECT REPLY CODE 10AB22 CCLCD 14SHAPE,SECTION,BATTENED BATTENED SECTION SHAPE THE PHYSICAL CONFIGURATION OF THE BATTENED SECTION(S). SELECT REPLY CODE 10AD07 CCLDD 11METHOD,FASTENING,BATTENED SECTION BATTENED SECTION FASTENING METHOD THE MEANS BY WHICH THE BATTENED SECTION IS FASTENED. SELECT REPLY CODE 10AF69 CCLFA 12QUANTITY,FASTENER,BATTENED SECTION BATTENED SECTION FASTENER QUANTITY THE NUMBER OF BATTENED SECTION FASTENERS PROVIDED. 1A MODE REPLY 0 CCLGA 12QUANTITY,ANCHOR,BATTENED SECTION TRACTION BAR BATTENED SECTION TRACTION BAR ANCHOR QUANTITY THE NUMBER OF BATTENED SECTION TRACTION BAR ANCHORS PROVIDED. 1A MODE REPLY 0 CCLHA 12QUANTITY,BATTEN,BATTENED SECTION BATTENED SECTION BATTEN QUANTITY THE NUMBER OF BATTENS PROVIDED IN THE BATTENED SECTION. 1A MODE REPLY 0 CCLJD 11METHOD,FASTENING,EXTENSION SECTION EXTENSION SECTION FASTENING METHOD THE MEANS BY WHICH THE EXTENSION SECTION IS FASTENED. SELECT REPLY CODE 10AF69 CCLKD 11METHOD,FASTENING,CUFF CUFF FASTENING METHOD THE MEANS BY WHICH THE CUFF IS FASTENED. SELECT REPLY CODE 10AF69 CCLLA 12QUANTITY,PAIR,CUFF FASTENER CUFF FASTENER PAIR QUANTITY THE NUMBER OF PAIRS OF CUFF FASTENERS PROVIDED. 1A MODE REPLY 0 CCLMD /D/ 07STRAP,TRACTION,FOOT FOOT TRACTION STRAP AN INDICATION OF WHETHER OR NOT A FOOT TRACTION STRAP IS PROVIDED. SELECT REPLY CODE 10AB22 CCLNJ 04DIAMETER,INSIDE,CLEANOUT CLEANOUT INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO SURFACES OF THE CLEANOUT,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CCLPJ 04HEIGHT,INSIDE,CLEANOUT CLEANOUT INSIDE HEIGHT AN INSIDE MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE ITEM,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CCLQJ 04WIDTH,INSIDE,CLEANOUT CLEANOUT INSIDE WIDTH AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A CLEANOUT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CCLRJ A18TYPE AND QUANTITY,FITTING FITTING TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF FITTINGS PROVIDED. 1D AND 1A MODE REPLY13AM35 CCLSG 04SIZE,FITTING FITTING SIZE DESIGNATES THE SIZE OF THE FITTING(S) PROVIDED. FULL TEXT WRITE-IN 0 CCLTG 08LOCATION,FITTING FITTING LOCATION INDICATES THE LOCATION OF THE FITTING. FULL TEXT WRITE-IN 0 CCLWA 12QUANTITY,OPENING,FITTING FITTING OPENING QUANTITY THE NUMBER OF FITTING OPENINGS PROVIDED. 1A MODE REPLY 0 CCLXD /D/ 07PROVISION,THREAD,FITTING OPENING FITTING OPENING THREAD PROVISION AN INDICATION OF WHETHER THE FITTING OPENING IS THREADED. SELECT REPLY CODE 10AK54 CCLYJ 04DIAMETER,OPENING,FITTING FITTING OPENING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FITTING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CCLZG 08LOCATION,OPENING,FITTING FITTING OPENING LOCATION INDICATES THE LOCATION OF THE FITTING OPENING. FULL TEXT WRITE-IN 0 CCMBD 08LOCATION,LADDER LADDER LOCATION INDICATES THE LOCATION OF THE LADDER. SELECT REPLY CODE 10AK54 CCMCD /D/ 07SHOWER SHOWER AN INDICATION OF WHETHER OR NOT A SHOWER IS INCLUDED. SELECT REPLY CODE 10AA49 CCMDD /D/ 07ROOF ROOF AN INDICATION OF WHETHER OR NOT A ROOF IS INCLUDED. SELECT REPLY CODE 10AA49 CCMFD /D/ 14SHAPE,ROOF ROOF SHAPE THE PHYSICAL CONFIGURATION OF THE ROOF. SELECT REPLY CODE 10AD07 CCMGG 19NAME,ITEM,SUPPORTED SUPPORTED ITEM NAME THE NAME OF THE SUPPORTED ITEM/S/. FULL TEXT WRITE-IN 0 CCMHJ 04LENGTH,BOTTOM BOTTOM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BOTTOM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CCMJJ 04LENGTH,TOP TOP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TOP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CCMKD 19FACILITY,CLIMBING CLIMBING FACILITY THE FACILITY PROVIDED FOR CLIMBING THE ITEM. SELECT REPLY CODE 10AK54 CCMLA 12QUANTITY,PLATFORM,REST REST PLATFORM QUANTITY THE NUMBER OF REST PLATFORMS PROVIDED. 1A MODE REPLY 0 CCMMD /D/ 07CABIN CABIN AN INDICATION OF WHETHER OR NOT A CABIN IS INCLUDED. SELECT REPLY CODE 10AA49 CCMND /D/ 09MATERIAL,CABIN CABIN MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CABIN IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCMPD /D/ 17SURFACE TREATMENT,CABIN CABIN SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE CABIN SURFACE. SELECT REPLY CODE 10AD09 CCMQD /D/ 07LADDER,ROOF ROOF LADDER AN INDICATION OF WHETHER OR NOT A ROOF LADDER IS INCLUDED. SELECT REPLY CODE 10AA49 CCMRJ 04DIAMETER,CABIN CABIN DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CABIN,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CCMSJ 04HEIGHT,CABIN CABIN HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE CABIN,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CCMTJ 04LENGTH,CABIN CABIN LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CABIN,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CCMWJ 04WIDTH,CABIN CABIN WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CABIN,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CCMXD /D/ 07ROD,LIGHTNING LIGHTNING ROD AN INDICATION OF WHETHER OR NOT A LIGHTNING ROD(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CCMYD 19FACILITY,ELEVATING ELEVATING FACILITY AN INDICATION OF THE TYPE OF ELEVATING FACILITY INCLUDED. SELECT REPLY CODE 10AK95 CCMZA 12QUANTITY,SIDE,LATERAL LATERAL SIDE QUANTITY THE NUMBER OF LATERAL SIDES PROVIDED. 1A MODE REPLY 0 CCNBD 02DESIGN,SECTION SECTION DESIGN THE DESIGN OF THE SECTION(S). SELECT REPLY CODE 10AK54 CCNCG 02DESIGN,FUNCTION FUNCTION DESIGN THE DESIGN FUNCTION OF THE ITEM. FULL TEXT WRITE-IN 0 CCNDG /D/ 19LIQUID FOR WHICH DESIGNED LIQUID FOR WHICH DESIGNED THE LIQUID FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 CCNFG 19APPLICATION/FUNCTION APPLICATION/FUNCTION THE APPLICATION AND/OR FUNCTION FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 CCNGD 18TYPE,PITCH PITCH TYPE INDICATES THE TYPE OF PITCH USED WITH THE ITEM. SELECT REPLY CODE 10AL59 CCNHJ 04RADIUS AT WHICH PITCH IS MEASURED,SECTIONAL,BLADE BLADE SECTIONAL RADIUS AT WHICH PITCH IS MEASURED THE SECTIONAL RADIUS OF THE BLADE AT WHICH THE DESIGNED PITCH IS MEASURED. 1D AND 1B MODE REPLY11AA05 CCNJJ 10PITCH,DESIGN DESIGN PITCH THE MEAN DISTANCE OF FORWARD MOVEMENT FOR EACH REVOLUTION OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CCNKJ /D/ 04LENGTH,LUFF LUFF LENGTH A MEASUREMENT OF THE LONGEST DIMENSION BETWEEN THE TOP AND BOTTOM OF THE FORWARD EDGE OF THE ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CCNLJ /D/ 04LENGTH,LEECH LEECH LENGTH A MEASUREMENT OF THE LONGEST DIMENSION BETWEEN THE TOP AND BOTTOM OF THE AFTER EDGE OF THE ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CCNMJ /D/ 04LENGTH,FOOT FOOT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION BETWEEN THE ENDS OF THE LOWER EDGE OF THE ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CCNNA 12QUANTITY,VIAL VIAL QUANTITY THE NUMBER OF VIALS PROVIDED ON THE ITEM. 1A MODE REPLY 0 CCNPD 19ARRANGEMENT,VIAL VIAL ARRANGEMENT THE ARRANGEMENT OF THE VIALS ON THE ITEM. SELECT REPLY CODE 10AM39 CCNQD /D/ 07GRADUATIONS,VIAL VIAL GRADUATIONS AN INDICATION OF WHETHER OR NOT VIAL GRADUATIONS ARE INCLUDED. SELECT REPLY CODE 10AA49 CCNRG 10VALUE,GRADUATION,VIAL VIAL GRADUATION VALUE THE VALUE REPRESENTED BY EACH GRADUATION ON THE VIAL. FULL TEXT WRITE-IN 0 CCNSD 19FINISH,SURFACE,VIAL VIAL SURFACE FINISH AN ADDITIONAL FINISHING PROCESS BY WHICH THE SURFACE OF THE VIAL IS ALTERED IN RESPECT TO POLISHING,GRINDING,AND THE LIKE. SELECT REPLY CODE 10AA41 CCNTF T10RANGE IN MINUTES,GRADUATION,VIAL VIAL GRADUATION RANGE IN MINUTES THE MINIMUM AND MAXIMUM VALUES REPRESENTED BY THE GRADUATIONS ON THE VIAL,EXPRESSED IN MINUTES. 1F MODE REPLY 0 CCNWD /D/ 07VIAL IN ACCORDANCE W/MILITARY STD VIAL IN ACCORDANCE W/MILITARY STD AN INDICATION OF WHETHER OR NOT A VIAL IN ACCORDANCE WITH A MILITARY STANDARD IS PROVIDED. SELECT REPLY CODE 10AB22 CCNXG /D/ 03DESIGNATOR,STANDARD,MILITARY MILITARY STANDARD DESIGNATOR A DESIGNATION ASSIGNED TO THE MILITARY STANDARD. FULL TEXT WRITE-IN 0 CCNYD 14SHAPE,VIAL VIAL SHAPE THE PHYSICAL CONFIGURATION OF THE VIAL. SELECT REPLY CODE 10AD07 CCNZD 01COLOR,LIQUID LIQUID COLOR THE HUE OR TINT OF THE LIQUID. SELECT REPLY CODE 10AD06 CCPBD 18TYPE,VIAL VIAL TYPE INDICATES THE TYPE OF VIAL FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AK54 CCPCJ 04LENGTH,SLOT,LOCK,VISOR VISOR LOCK SLOT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SLOT PROVIDED FOR THE VISOR LOCK,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CCPDD 18TYPE FOR WHICH DESIGNED,FRAME FRAME TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF FRAME FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AH28 CCPFD /D/ 09MATERIAL,GUIDE,VISOR VISOR GUIDE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE VISOR GUIDE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCPGD /D/ 09MATERIAL,SPRING,GUIDE,VISOR VISOR GUIDE SPRING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE VISOR GUIDE SPRING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCPHD /D/ 09MATERIAL,KNOB KNOB MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE KNOB IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCPJD 01COLOR,KNOB KNOB COLOR THE HUE OR TINT OF THE KNOB. SELECT REPLY CODE 10AD06 CCPKD /D/ 07FEATURE,POLARIZATION,LENS LENS POLARIZATION FEATURE AN INDICATION OF WHETHER OR NOT THE LENS INCLUDES A POLARIZATION FEATURE. SELECT REPLY CODE 10AA49 CCPLJ /D/ 04THICKNESS,OVERALL,LENS LENS OVERALL THICKNESS AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF THE LENS,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CCPMF /D/T10RANGE IN PERCENT,TRANSMISSION,LENS,RAY RAY LENS TRANSMISSION RANGE IN PERCENT THE MINIMUM AND MAXIMUM VALUES OF THE RAYS TRANSMITTED BY THE LENS,EXPRESSED IN PERCENT. 1F MODE REPLY 0 CCPND /D/ 07FRAME,OPAQUE OPAQUE FRAME AN INDICATION OF WHETHER OR NOT AN OPAQUE FRAME IS INCLUDED. SELECT REPLY CODE 10AA49 CCPPD /D/ 09MATERIAL,LENS,FILTER FILTER LENS MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FILTER LENS IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCPQF T10RANGE IN MILLIMICRONS,WAVELENGTH,FILTER LENS LIGHT TRANSMISSION FILTER LENS LIGHT TRANSMISSION WAVELENGTH RANGE IN MILLIMICRONS THE MINIMUM AND MAXIMUM VALUES OF THE LIGHT WAVELENGTH TRANSMITTED BY THE FILTER LENS,EXPRESSED IN MILLIMICRONS. 1F MODE REPLY 0 CCPRG 04SIZE,LENS,FILTER FILTER LENS SIZE DESIGNATES THE SIZE OF THE TOTAL SURFACE OF THE LENS FILTER. FULL TEXT WRITE-IN 0 CCPSD 18TYPE,HEADBAND HEADBAND TYPE INDICATES THE TYPE OF HEADBAND FURNISHED. SELECT REPLY CODE 10AF69 CCPTD /D/ 07FEATURE,OPTIC,LENS LENS OPTIC FEATURE AN INDICATION OF WHETHER OR NOT THE LENS INCLUDES AN OPTIC FEATURE. SELECT REPLY CODE 10AA49 CCPWD /D/ 07BRIDGE,NOSE,HINGED HINGED NOSE BRIDGE AN INDICATION OF WHETHER OR NOT A HINGED NOSE BRIDGE IS INCLUDED. SELECT REPLY CODE 10AA49 CCPXD /D/ 07REST,BROW BROW REST AN INDICATION OF WHETHER OR NOT A BROW REST IS INCLUDED. SELECT REPLY CODE 10AA49 CCPYD /D/ 09MATERIAL,REST,BROW BROW REST MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BROW REST IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH ISAC REPLY TABLE 0014 IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 CCPZD 18TYPE,REST,BROW BROW REST TYPE INDICATES THE TYPE OF BROW REST PROVIDED. SELECT REPLY CODE 10AK54 CCQBD /D/ 09MATERIAL,PAD,NOSE NOSE PAD MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE NOSE PAD IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH ISAC REPLY TABLE 0014 IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 CCQCD 07ADJUSTABILITY,PAD,NOSE NOSE PAD ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE NOSE PAD IS ADJUSTABLE. SELECT REPLY CODE 10AB00 CCQDD 18TYPE,PAD,NOSE NOSE PAD TYPE INDICATES THE TYPE OF NOSE PAD PROVIDED. SELECT REPLY CODE 10AG25 CCQFD /D/ 09MATERIAL,PIECE,TEMPLE TEMPLE PIECE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TEMPLE PIECE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH ISAC REPLY TABLE 0014 IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 CCQGD 07ADJUSTABILITY,PIECE,TEMPLE TEMPLE PIECE ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE TEMPLE PIECE IS ADJUSTABLE. SELECT REPLY CODE 10AB00 CCQHD /D/ 18TYPE,PIECE,TEMPLE TEMPLE PIECE TYPE INDICATES THE TYPE OF TEMPLE PIECE PROVIDED. SELECT REPLY CODE 10AK54 CCQJD /D/ 09MATERIAL,MASK MASK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MASK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCQKD 01COLOR,MASK MASK COLOR THE HUE OR TINT OF THE MASK. SELECT REPLY CODE 10AD06 CCQLD 18TYPE,FILTER,SINGLE EYE CELL SINGLE EYE CELL FILTER TYPE INDICATES THE TYPE OF SINGLE EYE CELL FILTER PROVIDED. SELECT REPLY CODE 10AH81 CCQMD /D/ 07FEATURE,INTERCHANGEABLE INTERCHANGEABLE FEATURE AN INDICATION OF WHETHER OR NOT AN INTERCHANGEABLE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CCQNJ 04SIZE ACCOMMODATED,WIRE WIRE SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE WIRE THE ITEM IS DESIGNED TO ACCOMMODATE. 2D AND 1B MODE REPLY21AB961AC20 CCQPD /D/ 07ATTACHMENT,STEPLADDER STEPLADDER ATTACHMENT AN INDICATION OF WHETHER OR NOT A STEPLADDER ATTACHMENT IS INCLUDED. SELECT REPLY CODE 10AA49 CCQQJ /D/ 04DEPTH,WELL,INSIDE INSIDE WELL DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE INSIDE OF A WELL,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CCQRB /D/ 10GRAVITY RATING,SPECIFIC,DRY FORM DRY FORM SPECIFIC GRAVITY RATING AN INDICATION OF THE SPECIFIC GRAVITY RATING OF THE DRY FORM. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 1B MODE REPLY 0 CCQSD /D/ 07WING,FOLDING,BARREL SUPPORT BARREL SUPPORT FOLDING WING AN INDICATION OF WHETHER OR NOT A FOLDING WING/S/ TO SUPPORT A BARREL IS INCLUDED. SELECT REPLY CODE 10AA49 CCQTD 14SHAPE,CROSSBAR,FRAME FRAME CROSSBAR SHAPE THE PHYSICAL CONFIGURATION OF THE CROSSBAR(S) OF THE FRAME. SELECT REPLY CODE 10AD07 CCQWD /D/ 07FRAME,BACK,SOLID SOLID BACK FRAME AN INDICATION OF WHETHER OR NOT THE FRAME HAS A SOLID BACK INCLUDED. SELECT REPLY CODE 10AA49 CCQXD /D/ 07FRAME,TAPERED TAPERED FRAME AN INDICATION OF WHETHER OR NOT A TAPERED FRAME IS INCLUDED. SELECT REPLY CODE 10AA49 CCQYJ 04LENGTH,NOSE NOSE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE NOSE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CCQZD /D/ 07BOX,EQUIPMENT EQUIPMENT BOX AN INDICATION OF WHETHER OR NOT AN EQUIPMENT BOX IS INCLUDED. SELECT REPLY CODE 10AA49 CCRBD /D/ 09MATERIAL,BOX BOX MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BOX IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCRCJ /D/ 04DEPTH,BOX BOX DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON A BOX,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CCRDD /D/ 07BOX,DUMP DUMP BOX AN INDICATION OF WHETHER OR NOT A DUMP BOX IS INCLUDED. SELECT REPLY CODE 10AA49 CCRFD /D/ 18TYPE,LID,BOX BOX LID TYPE INDICATES THE TYPE OF LID ON THE BOX. SELECT REPLY CODE 10AK54 CCRGD /D/ 07COCK,DRAIN DRAIN COCK AN INDICATION OF WHETHER OR NOT A DRAIN COCK IS INCLUDED. SELECT REPLY CODE 10AA49 CCRHD /D/ 07BRAKE,FOOT FOOT BRAKE AN INDICATION OF WHETHER OR NOT A FOOT BRAKE IS INCLUDED. SELECT REPLY CODE 10AA49 CCRJD 18TYPE,SHELF SHELF TYPE INDICATES THE TYPE OF SHELF(VES) PROVIDED. SELECT REPLY CODE 10AK54 CCRKG 04SPACING,SHELF SHELF SPACING THE SPACING BETWEEN SHELVES. FULL TEXT WRITE-IN 0 CCRLJ 04LENGTH,SHELF SHELF LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SHELF,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CCRMD /D/ 07DIVIDER,SHELF SHELF DIVIDER AN INDICATION OF WHETHER OR NOT A SHELF DIVIDER(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CCRND /D/ 09MATERIAL,CHASSIS CHASSIS MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CHASSIS IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCRPD 07REMOVABILITY,SHELF SHELF REMOVABILITY AN INDICATION OF WHETHER OR NOT A SHELF(VES) IS REMOVABLE. SELECT REPLY CODE 10AB00 CCRQD /D/ 09MATERIAL,FRAME/PLATFORM FRAME/PLATFORM MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH A FRAME AND/OR PLATFORM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCRRD /D/ 07FEATURE,LINKED,CHAIN CHAIN LINKED FEATURE AN INDICATION OF WHETHER OR NOT A CHAIN LINKED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CCRSG 08LOCATION,ELEMENT,ROLLING ROLLING ELEMENT LOCATION INDICATES THE LOCATION OF THE ROLLING ELEMENT(S). FULL TEXT WRITE-IN 0 CCRTJ 04HEIGHT ABOVE FLOOR,PLATFORM PLATFORM HEIGHT ABOVE FLOOR A MEASUREMENT FROM THE FLOOR TO THE TOP OF THE PLATFORM,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CCRWD 18TYPE,DRAWBAR DRAWBAR TYPE INDICATES THE TYPE OF DRAWBAR PROVIDED. SELECT REPLY CODE 10AK54 CCRXD 19CONSTRUCTION,DRAWBAR DRAWBAR CONSTRUCTION AN INDICATION OF THE CONSTRUCTION OF THE DRAWBAR. SELECT REPLY CODE 10AL59 CCRYA 12QUANTITY,COUPLING COUPLING QUANTITY THE NUMBER OF COUPLINGS PROVIDED. 1A MODE REPLY 0 CCRZA 12QUANTITY,STAKE STAKE QUANTITY THE NUMBER OF STAKES PROVIDED. 1A MODE REPLY 0 CCSBA 12QUANTITY,POCKET,STAKE STAKE POCKET QUANTITY THE NUMBER OF STAKE POCKETS PROVIDED. 1A MODE REPLY 0 CCSCJ 04HEIGHT,STAKE STAKE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A STAKE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CCSDD 18TYPE,FORMULATION,BASIC BASIC FORMULATION TYPE INDICATES THE TYPE OF BASIC FORMULATION COMPOSING THE ITEM. SELECT REPLY CODE 10AJ06 CCSFA 19NUMBER,ACID,MAXIMUM MAXIMUM ACID NUMBER THE MAXIMUM NUMBER THAT REPRESENTS THE ACID CONDITION OF THE ITEM. 1A MODE REPLY 0 CCSGJ 04HEIGHT,LIFT,NO LOAD NO LOAD LIFT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE LIFT WITHOUT A LOAD,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CCSHJ 04HEIGHT,LIFT,MAXIMUM LOAD MAXIMUM LOAD LIFT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE LIFT WITH MAXIMUM LOAD,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 CCSJJ /D/ 04LENGTH AND TYPE,FACILITY,LOAD LOAD FACILITY LENGTH AND TYPE A MEASUREMENT OF THE LONGEST DIMENSION OF THE LOAD FACILITY AND THE TYPE PROVIDED. 3D AND 1B MODE REPLY31AA051AC202AC55 CCSKJ 04LENGTH,BOLSTER BOLSTER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A BOLSTER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CCSLJ 04HEIGHT,MAXIMUM,LOAD LOAD MAXIMUM HEIGHT THE MAXIMUM MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE LOAD. 1D AND 1B MODE REPLY11AA05 CCSMJ 04WIDTH,MAXIMUM,LOAD LOAD MAXIMUM WIDTH THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE LOAD. 1D AND 1B MODE REPLY11AA05 CCSNJ 04DISTANCE TO FIRST HOLE,BASE STEM BASE STEM DISTANCE TO FIRST HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 CCSPJ 04DISTANCE TO CENTERLINE HOLE,FIRST HOLE FIRST HOLE DISTANCE TO CENTERLINE HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 CCSQJ 04DEPTH,STEM SOCKET STEM SOCKET DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCSRJ 04DIAMETER,SOCKET,STEM STEM SOCKET DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CCSSJ 04WIDTH,SOCKET,STEM STEM SOCKET WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCSTJ /D/ 04DIAMETER,PLATE,STEM SOCKET STEM SOCKET PLATE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CCSWJ 04HEIGHT,OVERALL,STEM SOCKET STEM SOCKET OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CCSXJ /D/ 04LENGTH,PLATE,STEM SOCKET STEM SOCKET PLATE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCSYJ /D/ 04WIDTH,PLATE,STEM SOCKET STEM SOCKET PLATE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCSZJ /D/ 04LENGTH,SLOT,STEM SOCKET MOUNTING STEM SOCKET MOUNTING SLOT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCTBJ /D/ 04WIDTH,SLOT,STEM SOCKET MOUNTING STEM SOCKET MOUNTING SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCTCJ /D/ 04DIAMETER,HOLE,STEM SOCKET STEM SOCKET HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CCTDJ /D/ 04DISTANCE BETWEEN SLOTS ON STEM SOCKET,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SLOTS ON STEM SOCKET NONE. 2D AND 1B MODE REPLY21AA051AC20 CCTFA /D/ 12QUANTITY,HOLE,STEM SOCKET MOUNTING STEM SOCKET MOUNTING HOLE QUANTITY NONE. 1A MODE REPLY 0 CCTGA /D/ 12QUANTITY,SLOT,STEM SOCKET MOUNTING STEM SOCKET MOUNTING SLOT QUANTITY NONE. 1A MODE REPLY 0 CCTHJ /D/ 04DISTANCE FROM CENTER OF ANGLE PLATE TO HOLE DISTANCE FROM CENTER OF ANGLE PLATE TO HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 CCTJJ /D/ 04DISTANCE FROM CENTER OF ANGLE PLATE TO SLOT DISTANCE FROM CENTER OF ANGLE PLATE TO SLOT NONE. 2D AND 1B MODE REPLY21AA051AC20 CCTKJ /D/ 04DISTANCE FROM BOTTOM EDGE OF ANGLE PLATE TO HOLE DISTANCE FROM BOTTOM EDGE OF ANGLE PLATE TO HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 CCTLJ /D/ 04DISTANCE FROM BOTTOM EDGE OF ANGLE PLATE TO SLOT DISTANCE FROM BOTTOM EDGE OF ANGLE PLATE TO SLOT NONE. 2D AND 1B MODE REPLY21AA051AC20 CCTMJ /D/ 04DISTANCE FROM CENTER OF SOCKET HOLE TO OUTER SURFACE OF PLATE DISTANCE FROM CENTER OF SOCKET HOLE TO OUTER SURFACE OF PLATE NONE. 2D AND 1B MODE REPLY21AA051AC20 CCTNJ /D/ 04DISTANCE BETWEEN SECOND AND THIRD HOLE CENTERLINES DISTANCE BETWEEN SECOND AND THIRD HOLE CENTERLINES NONE. 2D AND 1B MODE REPLY21AA051AC20 CCTPJ 04LENGTH,PLATE,CASTER CASTER PLATE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCTQJ 04WIDTH,PLATE,CASTER CASTER PLATE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCTRJ 04DISTANCE BETWEEN MOUNTING SLOTS ALONG LENGTH,MAJOR,CENTER TO CENTER CENTER TO CENTER MAJOR DISTANCE BETWEEN MOUNTING SLOTS ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCTSJ 04DISTANCE BETWEEN MOUNTING SLOTS ALONG LENGTH,MINOR,CENTER TO CENTER CENTER TO CENTER MINOR DISTANCE BETWEEN MOUNTING SLOTS ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCTTJ 04DISTANCE BETWEEN MOUNTING SLOTS ALONG WIDTH,MAJOR,CENTER TO CENTER CENTER TO CENTER MAJOR DISTANCE BETWEEN MOUNTING SLOTS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCTWJ 04DISTANCE BETWEEN MOUNTING SLOTS ALONG WIDTH,MINOR,CENTER TO CENTER CENTER TO CENTER MINOR DISTANCE BETWEEN MOUNTING SLOTS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCTXB /D/ 19LEGEND D LEGEND D NONE. 1B MODE REPLY 0 CCTYB /D/ 19LEGEND V LEGEND V NONE. 1B MODE REPLY 0 CCTZJ 04LENGTH,SLOT,CASTER PLATE MOUNTING CASTER PLATE MOUNTING SLOT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCWBJ 04WIDTH,SLOT,CASTER PLATE MOUNTING CASTER PLATE MOUNTING SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCWCJ 04DIAMETER,HOLE,CASTER PLATE MOUNTING CASTER PLATE MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CCWDJ /D/ 04DISTANCE FROM KING BOLT HOLE CENTER TO MOUNTING HOLE CENTER ALONG LENGTH DISTANCE FROM KING BOLT HOLE CENTER TO MOUNTING HOLE CENTER ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCWFJ /D/ 04DISTANCE FROM KING BOLT HOLE CENTER TO MOUNTING HOLE CENTER ALONG WIDTH DISTANCE FROM KING BOLT HOLE CENTER TO MOUNTING HOLE CENTER ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CCWGA /D/ 12QUANTITY,HOLE,CASTER PLATE MOUNTING CASTER PLATE MOUNTING HOLE QUANTITY NONE. 1A MODE REPLY 0 CCWHA /D/ 12QUANTITY,SLOT,CASTER PLATE MOUNTING CASTER PLATE MOUNTING SLOT QUANTITY NONE. 1A MODE REPLY 0 CCWJG /D/ 08LOCATION AND QUANTITY,OPENING,ACCESS ACCESS OPENING LOCATION AND QUANTITY INDICATES THE LOCATION OF THE ACCESS OPENING(S) PROVIDED AND THE NUMBER OF EACH. FULL TEXT WRITE-IN 0 CCWKD /D/ 07BOX,SOUND SOUND BOX AN INDICATION OF WHETHER OR NOT A SOUND BOX IS INCLUDED. SELECT REPLY CODE 10AA49 CCWLJ 10BUOYANCY,RESERVE RESERVE BUOYANCY A RELATIVE MEASURE OF THE RESERVE BUOYANCY AN ITEM IS CAPABLE OF MAINTAINING WITH RESPECT TO ITS DENSITY. 1D AND 1B MODE REPLY12AG67 CCWMG 19COMPONENT AND QUANTITY,MAJOR MAJOR COMPONENT AND QUANTITY THE NAME OF THE MAJOR COMPONENTS AND THE NUMBER OF EACH. FULL TEXT WRITE-IN 0 CCWND /D/ 07CUSHION,AXILLARY AXILLARY CUSHION AN INDICATION OF WHETHER OR NOT AN AXILLARY CUSHION(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCWPD /D/ 07TAPER TO ACCOMMODATE TIP,END END TAPER TO ACCOMMODATE TIP AN INDICATION OF WHETHER OR NOT AN END TAPER TO ACCOMMODATE A TIP IS PROVIDED. SELECT REPLY CODE 10AB22 CCWQD 18TYPE,TUBE,ENEMA ENEMA TUBE TYPE INDICATES THE TYPE OF ENEMA TUBE PROVIDED. SELECT REPLY CODE 10AK54 CCWRD /D/ 07RESERVOIR,SHOULDERED SHOULDERED RESERVOIR AN INDICATION OF WHETHER OR NOT A SHOULDERED RESERVOIR(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCWSJ 04SIZE,BAG BAG SIZE DESIGNATES THE SIZE OF THE BAG. 1D AND 1B MODE REPLY11AA05 CCWTD /D/ 07TIP,NASAL NASAL TIP AN INDICATION OF WHETHER OR NOT A NASAL TIP(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCWWD 14SHAPE,BASIN,CATCH,CHAMBER CHAMBER CATCH BASIN SHAPE THE PHYSICAL CONFIGURATION OF THE CHAMBER CATCH BASIN. SELECT REPLY CODE 10AD07 CCWXD 14SHAPE,SECTION,CHAMBER TOP CHAMBER TOP SECTION SHAPE THE PHYSICAL CONFIGURATION OF THE CHAMBER TOP SECTION. SELECT REPLY CODE 10AD07 CCWYJ 04DIAMETER,INSIDE,TUBULATURE,BULB BULB TUBULATURE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO SURFACES OF A BULB TUBULATURE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CCWZJ 04DIAMETER,OUTSIDE,STEM,TUBING TUBING STEM OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBING STEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CCXBJ 04LENGTH,OVERALL,ENEMA TUBE ENEMA TUBE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ENEMA TUBE. 1D AND 1B MODE REPLY11AA05 CCXCJ 04DIAMETER,OUTSIDE,ENEMA TUBE TIP ENEMA TUBE TIP OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ENEMA TUBE TIP,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AF98 CCXDJ 04DIAMETER,OUTSIDE,ENEMA TUBE ENEMA TUBE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ENEMA TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CCXFJ 04HEIGHT,BOTTLE BOTTLE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BOTTLE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CCXGJ 04DIAMETER,BOTTLE BOTTLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOTTLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CCXHJ 04DIAMETER,INSIDE,BOTTLE MOUTH BOTTLE MOUTH INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TWO SURFACES OF A BOTTLE MOUTH,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CCXJD /D/ 07VALVE,INLET INLET VALVE AN INDICATION OF WHETHER OR NOT AN INLET VALVE(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCXKD 01COLOR,BULB BULB COLOR THE HUE OR TINT OF THE BULB. SELECT REPLY CODE 10AD06 CCXLD /D/ 08LOCATION,CAP,SCREW SCREW CAP LOCATION INDICATES THE LOCATION OF THE SCREW CAP(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 CCXMD /D/ 07STEM STEM AN INDICATION OF WHETHER OR NOT A STEM(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCXND /D/ 09MATERIAL,SECTION,NEEDLE NEEDLE SECTION MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE NEEDLE SECTION IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCXPD /D/ 19FORM,DESIGN,NEEDLE SECTION NEEDLE SECTION DESIGN FORM THE PHYSICAL CONFIGURATION OF THE NEEDLE SECTION. SELECT REPLY CODE 10AL52 CCXQD /D/ 18TYPE,DEVICE,STRIPPING STRIPPING DEVICE TYPE INDICATES THE TYPE OF STRIPPING DEVICE(S) PROVIDED. SELECT REPLY CODE 10AK95 CCXSD 18TYPE,DEVICE,GRASPING GRASPING DEVICE TYPE INDICATES THE TYPE OF GRASPING DEVICE(S) PROVIDED. SELECT REPLY CODE 10AK54 CCXTD /D/ 07CUTTER,OPERATED,SCREW SCREW OPERATED CUTTER AN INDICATION OF WHETHER OR NOT A SCREW OPERATED CUTTER/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 CCXWJ /D/ 04DIAMETER,DEVICE,GRASPING,SPIRAL SPIRAL GRASPING DEVICE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SPIRAL GRASPING DEVICE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AF98 CCXXD /D/ 07FEATURE,INTERCHANGEABLE,HANDLE HANDLE INTERCHANGEABLE FEATURE AN INDICATION OF WHETHER OR NOT A HANDLE INTERCHANGEABLE FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CCXYD /D/ 11METHOD,ATTACHMENT,HANDLE,SHAFT SHAFT HANDLE ATTACHMENT METHOD THE MEANS USED TO ATTACH THE HANDLE TO THE SHAFT. SELECT REPLY CODE 10AK54 CCXZD /D/ 19TREATMENT,RESISTANT,ABSORPTION ABSORPTION RESISTANT TREATMENT AN INDICATION OF THE TREATMENT USED TO RETARD ABSORPTION. SELECT REPLY CODE 10AA41 CCYBD /D/ 07CAPABILITY,BOILING BOILING CAPABILITY AN INDICATION OF WHETHER OR NOT THE ITEM CAN BE BOILED. SELECT REPLY CODE 10AH43 CCYCD /D/ 18TYPE,POINT,NEEDLE NEEDLE POINT TYPE INDICATES THE TYPE OF NEEDLE POINT(S) PROVIDED. SELECT REPLY CODE 10AJ44 CCYDD /D/ 07EYE,NEEDLE NEEDLE EYE AN INDICATION OF WHETHER OR NOT A NEEDLE EYE IS PROVIDED. SELECT REPLY CODE 10AB22 CCYFD 18TYPE,CONNECTION,OPENING OPENING CONNECTION TYPE INDICATES THE TYPE OF OPENING CONNECTION/S/ PROVIDED. SELECT REPLY CODE 10AB60 CCYGD /D/ 09MATERIAL,MESH MESH MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MESH IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCYHD /D/ 07COVERING,MESH,WIRE WIRE MESH COVERING AN INDICATION OF WHETHER OR NOT WIRE MESH COVERING IS PROVIDED. SELECT REPLY CODE 10AB22 CCYJJ /D/ 04DIAMETER,INSIDE,STEM,AORTIC AORTIC STEM INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN AORTIC STEM,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CCYKJ /D/ 04DIAMETER,INSIDE,LIMB LIMB INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE TWO SURFACES OF A CIRCULAR LIMB,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CCYLJ /D/ 04DIAMETER,INSIDE,RING RING INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A RING,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CCYMA /D/ 03DESIGNATION,SIZE,RING RING SIZE DESIGNATION THE SIZE DESIGNATION BY WHICH THE RING IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1A MODE REPLY 0 CCYND /D/ 11METHOD,MEASURING MEASURING METHOD THE MEANS USED FOR MEASURING VOLUME,WEIGHT,PRESSURE,AND THE LIKE,OF A SUBSTANCE. SELECT REPLY CODE 10AG67 CCYPJ /D/T10RANGE,SCALE,BURETTE UPPER STEM BURETTE UPPER STEM SCALE RANGE AN INDICATION OF THE SCALE LIMITS OF THE BURETTE UPPER STEM. 1D AND 1F MODE REPLY12AB49 CCYQJ /D/ 10DIVISION,SMALLEST,BURETTE UPPER STEM BURETTE UPPER STEM SMALLEST DIVISION AN INDICATION OF THE SMALLEST DIVISION MARKINGS OF A BURETTE UPPER STEM. 1D AND 1B MODE REPLY12AB49 CCYRJ /D/ 10GRADUATION,PORTION,LOWER,BURETTE BURETTE LOWER PORTION GRADUATION THE GRADUATED MARKINGS ON THE BURETTE LOWER PORTION. 1D AND 1B MODE REPLY12AB49 CCYSD /D/ 07DEVICE,SHAKING,ELECTRICAL ELECTRICAL SHAKING DEVICE AN INDICATION OF WHETHER OR NOT AN ELECTRICAL SHAKING DEVICE IS PROVIDED. SELECT REPLY CODE 10AB22 CCYTG /D/ 19NAME AND QUANTITY,UNIT,AUXILIARY AUXILIARY UNIT NAME AND QUANTITY THE NAME AND NUMBER OF AUXILIARY UNITS INCLUDED WITH THE ITEM. FULL TEXT WRITE-IN 0 CCYWD /D/ 07LINK,CONNECTING CONNECTING LINK AN INDICATION OF WHETHER OR NOT A CONNECTING LINK(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CCYXD /D/ 07TOTALIZER TOTALIZER AN INDICATION OF WHETHER OR NOT A TOTALIZER IS PROVIDED. SELECT REPLY CODE 10AB22 CCYYD /D/ 07PROVISION,THREAD,PISTON END CONNECTION PISTON END CONNECTION THREAD PROVISION AN INDICATION OF WHETHER A PORTION OF THE PISTON END CONNECTION IS THREADED. SELECT REPLY CODE 10AK54 CCYZD /D/ 07PROVISION,THREAD,CYLINDER END CONNECTION CYLINDER END CONNECTION THREAD PROVISION AN INDICATION OF WHETHER A PORTION OF THE CYLINDER END CONNECTION IS THREADED. SELECT REPLY CODE 10AK54 CCZBB /D/ 10LENGTH IN COUNTS,CYCLE CYCLE LENGTH IN COUNTS THE LENGTH OF THE CYCLE AS DETERMINED BY THE NUMBER OF COUNTS THE ITEM IS DESIGNED TO MAKE. 1B MODE REPLY 0 CCZCA 12QUANTITY,DEVICE,RESET RESET DEVICE QUANTITY THE NUMBER OF RESET DEVICES PROVIDED. 1A MODE REPLY 0 CCZDD /D/ 07WEIGHT,COATING,MATERIAL MATERIAL COATING WEIGHT AN INDICATION OF WHETHER OR NOT THE COATING WEIGHT IS INCLUDED IN THE MATERIAL WEIGHT. SELECT REPLY CODE 10AA49 CCZFJ /D/ 10WEIGHT,CLOTH,COATED COATED CLOTH WEIGHT AN INDICATION OF THE WEIGHT OF THE CLOTH AFTER BEING COATED. 2D AND 1B MODE REPLY22AG691AC20 CCZGD /D/ 09MATERIAL,BLADDER BLADDER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BLADDER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CCZHJ /D/ 10WEIGHT,MATERIAL,BLADDER,FINISHED FINISHED BLADDER MATERIAL WEIGHT A RELATIVE MEASURE OF THE MASS OF THE FINISHED BLADDER MATERIAL WITH RESPECT TO ITS DENSITY. 2D AND 1B MODE REPLY22AG671AC20 CCZJD /D/ 11METHOD,ADJUSTMENT,SIZE SIZE ADJUSTMENT METHOD THE MEANS USED TO ADJUST THE SIZE. SELECT REPLY CODE 10AL28 CCZKD 18TYPE,SUPPORT,MOBILITY MOBILITY SUPPORT TYPE INDICATES THE TYPE OF SUPPORT PROVIDED FOR MOBILITY. SELECT REPLY CODE 10AM61 CCZLD /D/ 07VALVE,SWITCH-OVER SWITCH-OVER VALVE AN INDICATION OF WHETHER OR NOT A SWITCH-OVER VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 CCZMA 12QUANTITY,ELEMENT,FILTERING FILTERING ELEMENT QUANTITY THE NUMBER OF FILTERING ELEMENTS PROVIDED. 1A MODE REPLY 0 CCZND 07FEATURE,REUSABILITY,ELEMENT ELEMENT REUSABILITY FEATURE THE DESIGN CAPABILITY WHICH ALLOWS THE ELEMENT TO BE CLEANED AND USED. SELECT REPLY CODE 10AJ61 CCZPD /D/ 07BLADE,CLEANING CLEANING BLADE AN INDICATION OF WHETHER OR NOT A CLEANING BLADE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CCZQD 11METHOD,ROTATION ROTATION METHOD THE MEANS BY WHICH THE ITEM IS ROTATED. SELECT REPLY CODE 10AC58 CCZRD /D/ 07VALVE,BYPASS,INTERNAL INTERNAL BYPASS VALVE AN INDICATION OF WHETHER OR NOT AN INTERNAL BYPASS VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 CCZSD 18TYPE,FLOW FLOW TYPE INDICATES THE TYPE OF FLOW PROVIDED. SELECT REPLY CODE 10AK04 CCZTD /D/ 07VALVE,BYPASS BYPASS VALVE AN INDICATION OF WHETHER OR NOT A BYPASS VALVE IS INCLUDED. PLEASE USE MRC ASHM IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 CCZWD /D/ 07VALVE,AIR-BLEED AIR-BLEED VALVE AN INDICATION OF WHETHER OR NOT AN AIR-BLEED VALVE IS INCLUDED. PLEASE USE MRC ASHM IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 CCZXD /D/ 08LOCATION,CONNECTION,INLET INLET CONNECTION LOCATION INDICATES THE LOCATION OF THE INLET CONNECTION(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 CCZYG /D/ 04SPACING/D/,HOLE,OUTLET FLANGE MOUNTING OUTLET FLANGE MOUNTING HOLE SPACING/D/ THE SPACING OF THE MOUNTING HOLES ON THE OUTLET FLANGE. FULL TEXT WRITE-IN 0 CCZZD /D/ 07PROVISION,THREAD,OUTLET FLANGE MOUNTING HOLE OUTLET FLANGE MOUNTING HOLE THREAD PROVISION AN INDICATION OF WHETHER OR NOT THE MOUNTING HOLE/S/ ON THE OUTLET FLANGE IS THREADED. SELECT REPLY CODE 10AE00 CDBBD /D/ 13THREAD SERIES,HOLE,OUTLET MOUNTING OUTLET MOUNTING HOLE THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF AN OUTLET MOUNTING HOLE. SELECT REPLY CODE 10AH06 CDBCD /D/ 13THREAD DIRECTION,HOLE,OUTLET MOUNTING OUTLET MOUNTING HOLE THREAD DIRECTION THE DIRECTION OF THE OUTLET MOUNTING HOLE THREAD WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AA38 CDBDD /D/ 07FITTING,OUTLET OUTLET FITTING AN INDICATION OF WHETHER OR NOT AN OUTLET FITTING IS INCLUDED. SELECT REPLY CODE 10AA49 CDBFD /D/ 08LOCATION,CONNECTION,OUTLET OUTLET CONNECTION LOCATION INDICATES THE LOCATION OF THE OUTLET CONNECTION(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 CDBGD /D/ 18TYPE,BRACKET BRACKET TYPE INDICATES THE TYPE OF BRACKET PROVIDED. SELECT REPLY CODE 10AK54 CDBHB 10FILTRATION RATING IN MICRONS,ABSOLUTE ABSOLUTE FILTRATION RATING IN MICRONS THE ABSOLUTE SIZE OF THE PARTICLE WHICH THE ELEMENT IS CAPABLE OF REMOVING FROM THE FLUID WHICH PASSES THROUGH THE FILTERING MATERIAL. 1B MODE REPLY 0 CDBJJ /D/ 04LENGTH,HOLE,MOUNTING MOUNTING HOLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING HOLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CDBKD /D/ 09MATERIAL,BOWL,SEDIMENT SEDIMENT BOWL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SEDIMENT BOWL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CDBLJ 10CAPACITY,FACILITY,STORAGE STORAGE FACILITY CAPACITY THE CAPACITY OF THE STORAGE FACILITY(IES). 1D AND 1B MODE REPLY12AG67 CDBMG 19NAME,MANUFACTURER,CIRCULATING PUMP CIRCULATING PUMP MANUFACTURER NAME THE NAME OF THE MANUFACTURER OF THE CIRCULATING PUMP. FULL TEXT WRITE-IN 0 CDBND /D/ 07DOWEL,PIPE,CENTER CENTER PIPE DOWEL AN INDICATION OF WHETHER OR NOT A CENTER PIPE DOWEL IS INCLUDED. SELECT REPLY CODE 10AA49 CDBPJ /D/ 04DISTANCE BETWEEN FABRIC STRIPS DISTANCE BETWEEN FABRIC STRIPS THE DISTANCE BETWEEN STRIPS OF FABRIC. 2D AND 1B MODE REPLY21AA051AC20 CDBQD 18TYPE,COLOR,GARNISHING GARNISHING COLOR TYPE INDICATES THE TYPE OF GARNISHING COLOR PROVIDED. SELECT REPLY CODE 10AL21 CDBRJ /D/ 04WIDTH,GARNISH GARNISH WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE GARNISH,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CDBSJ /D/ 04LENGTH,GARNISH GARNISH LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE GARNISH,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CDBTJ T10RANGE,ADJUSTABILITY ADJUSTABILITY RANGE THE MINIMUM AND MAXIMUM LIMITS OF THE ADJUSTMENT/S/ OF THE ITEM. 1D AND 1F MODE REPLY11AA05 CDBWD /D/ 07COLLAR,SUPPORT SUPPORT COLLAR AN INDICATION OF WHETHER OR NOT A SUPPORT COLLAR IS INCLUDED. SELECT REPLY CODE 10AA49 CDBXD /D/ 07CLAMP,COLLAR,ADJUSTABLE ADJUSTABLE COLLAR CLAMP AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE COLLAR CLAMP IS INCLUDED. SELECT REPLY CODE 10AA49 CDBYD /D/ 07PLATE,BASE BASE PLATE AN INDICATION OF WHETHER OR NOT A BASE PLATE IS INCLUDED. SELECT REPLY CODE 10AA49 CDBZD /D/ 07COLLECTOR,CABLE,COLUMN COLUMN CABLE COLLECTOR AN INDICATION OF WHETHER OR NOT A COLUMN CABLE COLLECTOR IS INCLUDED. SELECT REPLY CODE 10AA49 CDCBJ /D/ 04DIAMETER,INSIDE,PLATE PLATE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CDCCJ 04DIAMETER,OUTSIDE,PLATE PLATE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PLATE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDCDJ /D/ 04DIAMETER,HOLE,CABLE CABLE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CDCFJ 04DIAMETER,INSIDE,SECTION SECTION INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR SECTION,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDCGD /D/ 07FEATURE,DESIGN,SHRIMP NET SHRIMP NET DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A SHRIMP NET DESIGN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CDCHD /D/ 07GARNISHING GARNISHING AN INDICATION OF WHETHER OR NOT GARNISHING IS INCLUDED. SELECT REPLY CODE 10AA49 CDCJD /D/ 09MATERIAL,GARNISHING GARNISHING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE GARNISHING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CDCKD 19PATTERN,COLOR COLOR PATTERN THE PATTERN OF THE COLOR ON THE ITEM. SELECT REPLY CODE 10AK18 CDCLD 01COLOR,GARNISHING GARNISHING COLOR THE HUE OR TINT OF THE GARNISHING. SELECT REPLY CODE 10AD06 CDCMG /D/ 18TYPE AND LOCATION,DEVICE,ATTACHMENT ATTACHMENT DEVICE TYPE AND LOCATION INDICATES THE TYPE OF DEVICE USED FOR FASTENING AND/OR POSITIONING THE ITEM AND ITS LOCATION. FULL TEXT WRITE-IN 0 CDCND /D/ 07DEVICE,RELEASE,OUTSIDE EDGE EMBRASURE OUTSIDE EDGE EMBRASURE RELEASE DEVICE AN INDICATION OF WHETHER OR NOT AN OUTSIDE EDGE EMBRASURE RELEASE DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 CDCPA /D/ 12QUANTITY,EDGE,DEVICE ACCOMMODATED DEVICE ACCOMMODATED EDGE QUANTITY THE NUMBER OF EDGES WHICH WILL ACCOMMODATE A DEVICE(S). 1A MODE REPLY 0 CDCQD 03DESIGNATION,SIZE,MESH MESH SIZE DESIGNATION A DESIGNATION INDICATING THE MESH SIZE OF THE ITEM. SELECT REPLY CODE 10AF81 CDCRJ /D/ 04WIDTH,OPENING,CLEAR CLEAR OPENING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CLEAR OPENING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CDCSD 19PROTECTION,ENVIRONMENTAL,GARNISHING GARNISHING ENVIRONMENTAL PROTECTION THE ENVIRONMENTAL ELEMENT OR CONDITIONS THAT THE GARNISHING IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY. SELECT REPLY CODE 10AA65 CDCTA /D/ 12QUANTITY,BRACKET,AMMUNITION/MORTAR SECURING AMMUNITION/MORTAR SECURING BRACKET QUANTITY THE NUMBER OF AMMUNITION AND/OR MORTAR SECURING BRACKETS PROVIDED. 1A MODE REPLY 0 CDCWD /D/ 07STRAP,SECURING SECURING STRAP AN INDICATION OF WHETHER OR NOT A SECURING STRAP IS INCLUDED. SELECT REPLY CODE 10AA49 CDCXD /D/ 07LUNETTE LUNETTE AN INDICATION OF WHETHER OR NOT A LUNETTE IS INCLUDED. SELECT REPLY CODE 10AA49 CDCZJ /D/ 04DIAMETER,MINIMUM,NECK NECK MINIMUM DIAMETER THE MINIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE NECK,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CDDBJ 04DIAMETER,INSIDE,LARGE END LARGE END INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGE END,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDDCJ /D/ 04THICKNESS,END,LARGE LARGE END THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE LARGE END,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CDDDJ 04DIAMETER,INSIDE,SMALL END SMALL END INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALL END,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDDFJ /D/ 04THICKNESS,END,SMALL SMALL END THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE SMALL END,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CDDGJ 04WIDTH,RECESS RECESS WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A RECESS,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CDDHJ /D/ 04WIDTH,OPENING,HOLDING BRACKET BASE HOLDING BRACKET BASE OPENING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CDDJD 18TYPE,DESIGN,TIRE TIRE DESIGN TYPE INDICATES THE DESIGN TYPE OF THE TIRE. SELECT REPLY CODE 10AK54 CDDKD /D/ 19FEATURE FOR WHICH DESIGNED,BRAKING BRAKING FEATURE FOR WHICH DESIGNED AN INDICATION OF THE BRAKING FEATURE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 CDDLJ 04DIAMETER,INSIDE,INNER BEARING CONE INNER BEARING CONE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN INNER BEARING CONE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDDMJ 04DIAMETER,INSIDE,OUTER BEARING CONE OUTER BEARING CONE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN OUTER BEARING CONE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDDNA /D/ 12QUANTITY,VISOR VISOR QUANTITY THE NUMBER OF VISORS PROVIDED. 1A MODE REPLY 0 CDDPD /D/ 07CONTAINER CONTAINER AN INDICATION OF WHETHER OR NOT A CONTAINER IS INCLUDED. SELECT REPLY CODE 10AA49 CDDQD /D/ 07MATCH,MATERIAL,GARMENT GARMENT MATERIAL MATCH AN INDICATION OF WHETHER OR NOT A MATCH TO THE GARMENT MATERIAL IS PROVIDED. SELECT REPLY CODE 10AB22 CDDRD 18TYPE,BUCKLE BUCKLE TYPE INDICATES THE TYPE OF BUCKLE PROVIDED. SELECT REPLY CODE 10AE36 CDDSD /D/ 01COLOR,BUCKLE BUCKLE COLOR THE HUE OR TINT OF THE BUCKLE. SELECT REPLY CODE 10AD06 CDDTD /D/ 19SOURCE,SHADE,BUCKLE BUCKLE SHADE SOURCE THE NAME OF THE REFERENCE SOURCE OF THE BUCKLE SHADE IDENTIFICATION DESIGNATOR. SELECT REPLY CODE 10AF94 CDDWA /D/ 19SDENTIFICATION,SHADE,BUCKLE BUCKLE SHADE SDENTIFICATION A DESIGNATION ASSIGNED TO A PARTICULAR GRADATION OF A COLOR FOR PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 CDDXD /D/ 19SIZE FOR WHICH DESIGNED,JACKET JACKET SIZE FOR WHICH DESIGNED A DESIGNATION INDICATING THE JACKET SIZE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AF81 CDDYA /D/ 12QUANTITY,HOLE,ADJUSTMENT ADJUSTMENT HOLE QUANTITY THE NUMBER OF ADJUSTMENT HOLES PROVIDED. 1A MODE REPLY 0 CDDZD /D/ 07FASTENER FOR ATTACHING AMMUNITION MAGAZINE CARRIER,SNAP,FEMALE FEMALE SNAP FASTENER FOR ATTACHING AMMUNITION MAGAZINE CARRIER AN INDICATION OF WHETHER OR NOT A FEMALE SNAP FASTENER FOR ATTACHING AN AMMUNITION MAGAZINE CARRIER IS INCLUDED. SELECT REPLY CODE 10AA49 CDFBD /D/ 11METHOD,ATTACHMENT,EQUIPMENT EQUIPMENT ATTACHMENT METHOD THE MEANS BY WHICH EQUIPMENT IS ATTACHED TO THE ITEM. SELECT REPLY CODE 10AF69 CDFCD /D/ 11METHOD,ATTACHMENT,FIELD PACK SUSPENDERS FIELD PACK SUSPENDERS ATTACHMENT METHOD THE MEANS BY WHICH THE FIELD PACK SUSPENDERS ARE ATTACHED TO THE ITEM. SELECT REPLY CODE 10AF69 CDFDG /D/ 10CAPACITY/D/,POCKET POCKET CAPACITY/D/ THE CAPACITY OF THE POCKET. FULL TEXT WRITE-IN 0 CDFFD /D/ 07EYELETS ALONG TOP/BOTTOM FOR ATTACHING EQUIPMENT EYELETS ALONG TOP/BOTTOM FOR ATTACHING EQUIPMENT AN INDICATION OF WHETHER OR NOT EYELETS ALONG THE TOP AND BOTTOM FOR ATTACHING EQUIPMENT ARE INCLUDED. SELECT REPLY CODE 10AA49 CDFGA /D/ 12QUANTITY,STRAP,SHOULDER SHOULDER STRAP QUANTITY THE NUMBER OF SHOULDER STRAPS PROVIDED. 1A MODE REPLY 0 CDFHD /D/ 11METHOD,ADJUSTMENT,STRAP STRAP ADJUSTMENT METHOD THE MEANS USED TO ADJUST THE STRAP. SELECT REPLY CODE 10AF69 CDFJD /D/ 09MATERIAL,BINDING,EDGE EDGE BINDING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE EDGE BINDING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CDFKD /D/ 07THONG,CLAMP,HINGED HINGED CLAMP THONG AN INDICATION OF WHETHER OR NOT A HINGED CLAMP THONG IS INCLUDED. SELECT REPLY CODE 10AA49 CDFLJ /D/ 04WIDTH,OPENING,STRAP STRAP OPENING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE OPENING FOR THE STRAP,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CDFMG /D/ 18TYPE,ATTACHMENT,LOOP/END LOOP/END ATTACHMENT TYPE INDICATES THE TYPE OF LOOP(S) AND/OR END ATTACHMENT(S) PROVIDED ON THE ITEM. FULL TEXT WRITE-IN 0 CDFNA /D/ 12QUANTITY,EYELET,OUTER EDGE OUTER EDGE EYELET QUANTITY THE NUMBER OF EYELETS PROVIDED ON THE OUTER EDGE(S). 1A MODE REPLY 0 CDFPD /D/ 19SIZE FOR WHICH DESIGNED,BOOT BOOT SIZE FOR WHICH DESIGNED A DESIGNATION INDICATING THE BOOT SIZE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AF81 CDFQD /D/ 11METHOD,ATTACHMENT,RIFLE BUTT POCKET TO RUCKSACK RIFLE BUTT POCKET TO RUCKSACK ATTACHMENT METHOD THE MEANS OF ATTACHING THE RIFLE BUTT POCKET TO THE RUCKSACK. SELECT REPLY CODE 10AF69 CDFRG /D/ 11METHOD,ATTACHMENT,SECURING STRAP SECURING STRAP ATTACHMENT METHOD THE MEANS BY WHICH THE SECURING STRAP IS ATTACHED TO THE ITEM. FULL TEXT WRITE-IN 0 CDFSA /D/ 12QUANTITY IN ONE CONTINUOUS LENGTH,STOP STOP QUANTITY IN ONE CONTINUOUS LENGTH THE NUMBER OF STOPS PROVIDED IN ONE CONTINUOUS LENGTH. 1A MODE REPLY 0 CDFTJ /D/ 04LENGTH,OVERALL,INDIVIDUAL STOP INDIVIDUAL STOP OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE INDIVIDUAL STOP. 2D AND 1B MODE REPLY21AA051AC20 CDFWJ /D/ 04DISTANCE BETWEEN TIPS DISTANCE BETWEEN TIPS THE DISTANCE BETWEEN THE TIPS ON AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 CDFXD /D/ 17SURFACE TREATMENT,TIP TIP SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE TIP SURFACE. SELECT REPLY CODE 10AD09 CDFYD /D/ 01COLOR,MATERIAL,BASIC BASIC MATERIAL COLOR THE HUE OR TINT OF THE BASIC MATERIAL. SELECT REPLY CODE 10AD06 CDFZD /D/ 19SOURCE,SHADE,BASIC MATERIAL BASIC MATERIAL SHADE SOURCE THE NAME OF THE REFERENCE SOURCE OF THE BASIC MATERIAL SHADE IDENTIFICATION DESIGNATOR. SELECT REPLY CODE 10AF94 CDGBA /D/ 19IDENTIFICATION,SHADE,BASIC MATERIAL BASIC MATERIAL SHADE IDENTIFICATION A DESIGNATION ASSIGNED TO A PARTICULAR GRADATION OF A COLOR FOR PURPOSE OF READY IDENTIFICATION OF THE BASIC MATERIAL. 1A MODE REPLY 0 CDGCJ /D/ 04WIDTH,WAISTBAND WAISTBAND WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE WAISTBAND,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CDGDD /D/ 11METHOD,ADJUSTMENT,LENGTH LENGTH ADJUSTMENT METHOD THE MEANS USED TO REGULATE THE LENGTH OF THE ITEM. SELECT REPLY CODE 10AF69 CDGFD /D/ 11METHOD TO BELT,ATTACHMENT ATTACHMENT METHOD TO BELT THE MEANS BY WHICH THE ITEM IS ATTACHED TO A BELT. SELECT REPLY CODE 10AF69 CDGGD 18TYPE,STRAP STRAP TYPE INDICATES THE TYPE OF STRAP PROVIDED. SELECT REPLY CODE 10AC55 CDGHJ /D/ 04LENGTH,STRAP STRAP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE STRAP,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CDGJG /D/ 08LOCATION/D/,STRAP STRAP LOCATION/D/ INDICATES THE LOCATION OF THE STRAP IN OR ON THE ITEM. FULL TEXT WRITE-IN 0 CDGKD /D/ 08LOCATION,BUCKLE BUCKLE LOCATION INDICATES THE LOCATION OF THE BUCKLE(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 CDGLD /D/ 09MATERIAL,THONG THONG MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE THONG IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CDGMD /D/ 08LOCATION,THONG THONG LOCATION INDICATES THE LOCATION OF THE THONG(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 CDGNJ /D/ 04DIAMETER,OUTSIDE,CONE END CONE END OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CONE END,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CDGPJ /D/ 04LENGTH,SECTION,NEEDLE NEEDLE SECTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE NEEDLE SECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CDGQJ /D/ 04RADIUS,CURVATURE,NEEDLE SECTION NEEDLE SECTION CURVATURE RADIUS A MEASUREMENT OF A LINE EXTENDING FROM THE CONCAVE SIDE OF THE NEEDLE SECTION CURVE TO THE CURVATURE CENTER. 1D AND 1B MODE REPLY11AA05 CDGRJ 04DIAMETER,SHAFT SHAFT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR SHAFT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AF981AC20 CDGSJ 04DIAMETER,TIP TIP DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR TIP,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AF981AC20 CDGTJ /D/ 04LENGTH,HANDLE TO TIP HANDLE TO TIP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION FROM THE HANDLE TO THE TIP OF THE ITEM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CDGWJ /D/T04DISTANCE RANGE BETWEEN POINTS DISTANCE RANGE BETWEEN POINTS THE MINIMUM AND MAXIMUM RANGES OF DISTANCE BETWEEN POINTS. 1D AND 1F MODE REPLY11AA05 CDGXD /D/ 07PERIPHERY,INFLATABLE INFLATABLE PERIPHERY AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH AN INFLATABLE PERIPHERY. SELECT REPLY CODE 10AB22 CDGYD /D/ 07ATTACHMENT,HARNESS HARNESS ATTACHMENT AN INDICATION OF WHETHER OR NOT A HARNESS ATTACHMENT(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CDGZD /D/ 11METHOD,ATTACHMENT,MASK MASK ATTACHMENT METHOD THE MEANS USED TO ATTACH THE MASK TO THE ITEM. SELECT REPLY CODE 10AB47 CDHBD /D/ 11METHOD,ATTACHMENT,REFLECTOR REFLECTOR ATTACHMENT METHOD THE MEANS USED TO ATTACH THE REFLECTOR TO THE ITEM. SELECT REPLY CODE 10AB47 CDHCD /D/ 07PERFORATION,TONGUE,BUCKLE BUCKLE TONGUE PERFORATION AN INDICATION OF WHETHER OR NOT A BUCKLE TONGUE PERFORATION/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 CDHDD /D/ 07GRID GRID AN INDICATION OF WHETHER OR NOT A GRID(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CDHFD /D/ 18TYPE,GRID GRID TYPE INDICATES THE TYPE OF GRID PROVIDED. SELECT REPLY CODE 10AK54 CDHGG /D/ 04SPACING BETWEEN LINES SPACING BETWEEN LINES THE SPACING BETWEEN THE LINES. FULL TEXT WRITE-IN 0 CDHHJ T10RANGE,SCALE,GAGE GAGE SCALE RANGE THE MINIMUM TO MAXIMUM LIMITS OF THE GAGE SCALE. 1D AND 1F MODE REPLY12AB49 CDHJG /D/ 08LOCATION,MARKING,GAGE SCALE TOLERANCE GAGE SCALE TOLERANCE MARKING LOCATION INDICATES THE LOCATION(S) OF THE TOLERANCE MARKING(S) ON THE GAGE SCALE. FULL TEXT WRITE-IN 0 CDHKA 19NUMBER,GLASS GLASS NUMBER AN INDICATION OF THE NUMBER ASSIGNED TO THE GLASS. 1A MODE REPLY 0 CDHLJ 04DIAMETER,GLASS GLASS DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR GLASS,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDHMJ /D/ 04THICKNESS,HANDLE HANDLE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CDHNJ /D/ 04THICKNESS,RECTANGLE RECTANGLE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CDHPD /D/ 11METHOD,ATTACHMENT,HANDLE HANDLE ATTACHMENT METHOD THE MEANS USED TO ATTACH THE HANDLE TO THE ITEM. SELECT REPLY CODE 10AB47 CDHQD 03DESIGNATION,TEST TEST DESIGNATION A DESIGNATION DERIVED FOR THE NAME OF THE DESIGNER OR THE USE FOR WHICH THE ITEM IS INTENDED. SELECT REPLY CODE 10AJ50 CDHRD /D/ 07DISK,SEPARABLE SEPARABLE DISK AN INDICATION OF WHETHER OR NOT A SEPARABLE DISK(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CDHSD /D/ 07DISK,OPAQUE OPAQUE DISK AN INDICATION OF WHETHER OR NOT AN OPAQUE DISK(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CDHTD /D/ 01COLOR,DISK DISK COLOR THE HUE OR TINT OF THE DISK. SELECT REPLY CODE 10AD06 CDHWD /D/ 07APERTURE IN EACH DISK APERTURE IN EACH DISK AN INDICATION OF WHETHER OR NOT AN APERTURE IS PROVIDED IN EACH DISK. SELECT REPLY CODE 10AB22 CDHXD 11METHOD,ATTACHMENT,HEADBAND HEADBAND ATTACHMENT METHOD THE MEANS USED TO ATTACH THE HEADBAND. SELECT REPLY CODE 10AK08 CDHYD /D/ 18TYPE,MOUNTING,DISK DISK MOUNTING TYPE INDICATES THE TYPE OF MOUNT USED TO SUPPORT THE DISK. SELECT REPLY CODE 10AA78 CDHZJ /D/ 04WIDTH,BRIDGE BRIDGE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BRIDGE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CDJBJ /D/ 04DIAMETER,MAXIMUM,COMPARTMENT COMPARTMENT MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COMPARTMENT,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CDJCD /D/ 11METHOD,LOCKING,SECTION SECTION LOCKING METHOD THE MEANS USED TO LOCK THE SECTION(S) IN POSITION. SELECT REPLY CODE 10AE44 CDJDJ /D/ 04DIAMETER,STRAP STRAP DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A STRAP,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDJFJ 04LENGTH,ENVELOPE ENVELOPE LENGTH THE MEASUREMENT OF THE LONGEST DIMENSION OF AN ENVELOPE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CDJGJ 04DIAMETER,HOLE,REFLECTING ELEMENT REFLECTING ELEMENT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE REFLECTING ELEMENT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDJHJ 04LENGTH,FOCAL,REFLECTING ELEMENT REFLECTING ELEMENT FOCAL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION FROM THE CENTER OF A REFLECTING ELEMENT TO THE FOCAL PLANE. 2D AND 1B MODE REPLY21AA051AC20 CDJJJ 04LENGTH,OVERALL,LARGEST SECTION,HORIZONTAL AXIS HORIZONTAL AXIS LARGEST SECTION OVERALL LENGTH THE DIMENSION MEASURED ALONG THE HORIZONTAL AXIS AT THE LARGEST SECTION WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CDJKJ 04LENGTH,OVERALL,LARGEST SECTION,VERTICAL AXIS VERTICAL AXIS LARGEST SECTION OVERALL LENGTH THE DIMENSION MEASURED ALONG THE VERTICAL AXIS AT THE LARGEST SECTION WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CDJLA /D/ 12QUANTITY ACCOMMODATED,RECORD,MAXIMUM MAXIMUM RECORD QUANTITY ACCOMMODATED THE MAXIMUM NUMBER OF RECORDS THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 CDJMJ /D/ 04LENGTH,TAPE,ACCOMMODATED ACCOMMODATED TAPE LENGTH THE LENGTH OF TAPE THAT THE ITEM IS DESIGNED TO ACCOMMODATE. 2D AND 1B MODE REPLY21AA051AC20 CDJNJ /D/ 04LENGTH AND LOCATION,SIDE SIDE LENGTH AND LOCATION A MEASUREMENT OF THE LONGEST DIMENSION OF THE SIDE,IN DISTINCTION FROM WIDTH,AND ITS LOCATION. 3D AND 1B MODE REPLY31AA051AC203AJ91 CDJPD /D/ 07BAG BAG AN INDICATION OF WHETHER OR NOT A BAG IS PROVIDED. SELECT REPLY CODE 10AB22 CDJQG /D/ 19SOURCE,PATTERN/STYLE,COLOR COLOR PATTERN/STYLE SOURCE THE NAME OF THE GOVERNMENT AGENCY,COMMERCIAL ORGANIZATION,OR MANUFACTURER CONTROLLING THE COLOR PATTERN AND/OR STYLE. FULL TEXT WRITE-IN 0 CDJRG /D/ 19IDENTIFICATION,PATTERN/STYLE,COLOR COLOR PATTERN/STYLE IDENTIFICATION A DESIGNATION ASSIGNED TO A PARTICULAR COLOR PATTERN AND/OR STYLE FOR THE PURPOSE OF READY IDENTIFICATION. FULL TEXT WRITE-IN 0 CDJSD 18TYPE,TAILPIECE TAILPIECE TYPE INDICATES THE TYPE OF TAILPIECE FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AK54 CDJTD /D/ 07FEATURE,DESIGN,SCOOP SCOOP DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A SCOOP DESIGN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CDJWD /D/ 07HOLE,SCREW,WOOD WOOD SCREW HOLE AN INDICATION OF WHETHER OR NOT A WOOD SCREW HOLE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CDJXD 18TYPE,STEM STEM TYPE INDICATES THE TYPE OF STEM. SELECT REPLY CODE 10AK54 CDJYJ 04DIAMETER,OUTSIDE,SERRATION SERRATION OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SERRATION,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDJZJ 10DEGREE,PITCH PITCH DEGREE THE DEGREE OF PITCH OF THE ITEM. 1D AND 1B MODE REPLY11AC20 CDKBJ 04LENGTH,SPIGOT SPIGOT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SPIGOT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CDKCJ 04DIAMETER FOR WHICH DESIGNED,HUB,PROPELLER PROPELLER HUB DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PROPELLER HUB FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDKDG /D/ 18TYPE AND QUANTITY,FACILITY,MOUNTING MOUNTING FACILITY TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF FACILITIES FURNISHED TO MOUNT THE ITEM. FULL TEXT WRITE-IN 0 CDKFJ 04THICKNESS,LIP LIP THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CDKGJ 04DIAMETER,OUTSIDE,FRAME FRAME OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FRAME,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDKHJ 04WIDTH,OUTSIDE,FRAME FRAME OUTSIDE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE OUTSIDE LENGTH OF THE FRAME,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CDKJJ 04LENGTH,OPENING,FRAME FRAME OPENING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FRAME OPENING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CDKKJ 04LENGTH,OUTSIDE,FRAME FRAME OUTSIDE LENGTH A MEASUREMENT OF THE LONGEST OUTSIDE DIMENSION OF THE FRAME,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CDKLJ /D/ 04WIDTH,SPIGOT SPIGOT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SPIGOT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CDKMD /D/ 07RING,FINISHING,OUTSIDE OUTSIDE FINISHING RING AN INDICATION OF WHETHER OR NOT AN OUTSIDE FINISHING RING IS INCLUDED. SELECT REPLY CODE 10AA49 CDKND /D/ 07PIN,HINGE,REMOVABLE REMOVABLE HINGE PIN AN INDICATION OF WHETHER OR NOT A REMOVABLE HINGE PIN IS INCLUDED. SELECT REPLY CODE 10AA49 CDKPD /D/ 07GLASS IN HOLDER,PLATE PLATE GLASS IN HOLDER AN INDICATION OF WHETHER OR NOT PLATE GLASS IS INCLUDED IN THE HOLDER. SELECT REPLY CODE 10AA49 CDKQD /D/ 07FEATURE,FROSTED,GLASS ONE SIDE GLASS ONE SIDE FROSTED FEATURE AN INDICATION OF WHETHER OR NOT A FROSTED GLASS FEATURE ON ONE SIDE IS INCLUDED. SELECT REPLY CODE 10AA49 CDKRD /D/ 07SCREEN SCREEN AN INDICATION OF WHETHER OR NOT SELECT REPLY CODE 10AA49 CDKSD /D/ 07RING,SNAP,RETAINING RETAINING SNAP RING AN INDICATION OF WHETHER OR NOT A RETAINING SNAP RING IS INCLUDED. SELECT REPLY CODE 10AA49 CDKTD /D/ 07SHED,WATER WATER SHED AN INDICATION OF WHETHER OR NOT A WATER SHED IS INCLUDED. SELECT REPLY CODE 10AA49 CDKWD /D/ 09MATERIAL,SHED,WATER WATER SHED MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WATER SHED IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CDKXD /D/ 07DEADLIGHT,VENTILATING VENTILATING DEADLIGHT AN INDICATION OF WHETHER OR NOT A VENTILATING DEADLIGHT IS INCLUDED. SELECT REPLY CODE 10AA49 CDKYD /D/ 19CHARACTERISTICS,HINGE,GLASS FRAME/COVER GLASS FRAME/COVER HINGE CHARACTERISTICS THE CHARACTERISTICS OF THE GLASS FRAME AND COVER HINGE. SELECT REPLY CODE 10AK95 CDKZD /D/ 09MATERIAL,BAND BAND MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BAND IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CDLBD 14SHAPE,HORN HORN SHAPE THE PHYSICAL CONFIGURATION OF THE HORN. SELECT REPLY CODE 10AD07 CDLCD /D/ 07JAW,SWIVEL,AUXILIARY AUXILIARY SWIVEL JAW AN INDICATION OF WHETHER OR NOT AN AUXILIARY SWIVEL JAW IS INCLUDED. SELECT REPLY CODE 10AA49 CDLDD /D/ 07SOCKET SOCKET AN INDICATION OF WHETHER OR NOT A SOCKET IS INCLUDED. SELECT REPLY CODE 10AA49 CDLFD /D/ 07EYE,ATTACHING,SAFETY CHAIN SAFETY CHAIN ATTACHING EYE AN INDICATION OF WHETHER OR NOT AN EYE FOR ATTACHING SAFETY CHAIN IS INCLUDED. SELECT REPLY CODE 10AA49 CDLGJ 04DIAMETER ACCOMMODATED,POLE POLE DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE POLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDLHD /D/ 07POLE POLE AN INDICATION OF WHETHER OR NOT A POLE IS INCLUDED. SELECT REPLY CODE 10AA49 CDLJJ 04LENGTH,POLE POLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE POLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CDLKH /D/ 11METHOD AND LOCATION,CONSTRUCTION CONSTRUCTION METHOD AND LOCATION THE MEANS USED IN FABRICATING THE ITEM AND ITS LOCATION. 2D MODE REPLY 23AL593AJ91 CDLLJ 04LENGTH FROM CROWN TO CENTERLINE OF SHACKLE PIN HOLE,SHANK SHANK LENGTH FROM CROWN TO CENTERLINE OF SHACKLE PIN HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 CDLMJ 04LENGTH,OVERALL,STOCK STOCK OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CDLND 08LOCATION,BEARING BEARING LOCATION INDICATES THE LOCATION OF THE BEARING(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 CDLPD 18TYPE,BORE,AXLE AXLE BORE TYPE INDICATES THE TYPE OF AXLE BORE PROVIDED. SELECT REPLY CODE 10AL72 CDLQD /D/ 07BRAKE BRAKE AN INDICATION OF WHETHER OR NOT A BRAKE IS INCLUDED. SELECT REPLY CODE 10AA49 CDLRD /D/ 07DRUM,BRAKE BRAKE DRUM AN INDICATION OF WHETHER OR NOT A BRAKE DRUM(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CDLSA 12QUANTITY,NOTCH,VALVE CLEARANCE VALVE CLEARANCE NOTCH QUANTITY THE NUMBER OF VALVE CLEARANCE NOTCHES PROVIDED. 1A MODE REPLY 0 CDLTD /D/ 07SLOT,LEVERAGE LEVERAGE SLOT AN INDICATION OF WHETHER OR NOT A LEVERAGE SLOT IS INCLUDED. SELECT REPLY CODE 10AA49 CDLWD 13THREAD SERIES DESIGNATOR,SOCKET,STEM STEM SOCKET THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF A STEM SOCKET. SELECT REPLY CODE 10AH06 CDLXJ 04DIAMETER FOR WHICH DESIGNED,TIRE TIRE DIAMETER FOR WHICH DESIGNED THE DIAMETER OF THE TIRE FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AA05 CDLYD /D/ 07FEATURE,RIM,SPLIT SPLIT RIM FEATURE AN INDICATION OF WHETHER OR NOT A SPLIT RIM FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CDLZD /D/ 07LUG,HOLE,INTEGRAL MOUNTING BOLT INTEGRAL MOUNTING BOLT HOLE LUG AN INDICATION OF WHETHER OR NOT AN INTEGRAL MOUNTING BOLT HOLE LUG/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CDMBD 18TYPE,RING,RETAINING,TIRE TIRE RETAINING RING TYPE INDICATES THE TYPE OF TIRE RETAINING RING PROVIDED. SELECT REPLY CODE 10AB47 CDMCD 14SHAPE,HOLE,VALVE VALVE HOLE SHAPE THE PHYSICAL CONFIGURATION OF THE VALVE HOLE. SELECT REPLY CODE 10AD07 CDMDD /D/ 07DESIGN,APPLICATION,LIMITED CLEARANCE LIMITED CLEARANCE APPLICATION DESIGN AN INDICATION OF WHETHER OR NOT A LIMITED CLEARANCE APPLICATION DESIGN IS INCLUDED. SELECT REPLY CODE 10AA49 CDMFJ /D/ 04DISTANCE BETWEEN BEAM KINGPIN HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN BEAM KINGPIN HOLES THE DISTANCE BETWEEN THE BEAM KINGPIN HOLE CENTERS. 2D AND 1B MODE REPLY21AA051AC20 CDMGJ /D/ 04DISTANCE,MAXIMUM,SPINDLE CENTERLINE TO AXLE CENTERLINE SPINDLE CENTERLINE TO AXLE CENTERLINE MAXIMUM DISTANCE THE MAXIMUM DISTANCE FROM THE SPINDLE CENTERLINE TO THE AXLE CENTERLINE. 1D AND 1B MODE REPLY11AA05 CDMHJ /D/ 04DISTANCE BETWEEN SPRING SEATS,MAXIMUM,CENTER TO CENTER CENTER TO CENTER MAXIMUM DISTANCE BETWEEN SPRING SEATS THE MAXIMUM CENTER TO CENTER DISTANCE BETWEEN THE SPRING SEAT CENTERS. 1D AND 1B MODE REPLY11AA05 CDMJJ /D/ 04DIAMETER,SURFACE,LARGEST WHEEL BEARING LARGEST WHEEL BEARING SURFACE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST WHEEL BEARING SURFACE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDMKJ /D/ 04LENGTH,EFFECTIVE,SPINDLE SPINDLE EFFECTIVE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE EFFECTIVE LENGTH OF THE SPINDLE. 2D AND 1B MODE REPLY21AA051AC20 CDMLD /D/ 07FLANGE,PLATE,BRAKE BRAKE PLATE FLANGE AN INDICATION OF WHETHER OR NOT A BRAKE PLATE FLANGE IS INCLUDED. SELECT REPLY CODE 10AA49 CDMMB /D/ 10ANGULAR POSITION IN DEG,RELATIVE,ROD END ROD END RELATIVE ANGULAR POSITION IN DEG A MEASUREMENT OF THE RELATIVE POSITION OF THE ROD END(S),EXPRESSED IN DEGREES. 1B MODE REPLY 0 CDMND 08LOCATION,STUD,BALL BALL STUD LOCATION INDICATES THE LOCATION OF THE BALL STUD ON THE ITEM. SELECT REPLY CODE 10AJ91 CDMPD 08LOCATION,CLEVIS CLEVIS LOCATION INDICATES THE LOCATION OF THE CLEVIS ON THE ITEM. SELECT REPLY CODE 10AJ91 CDMQD 08LOCATION,CONNECTOR,ROD ROD CONNECTOR LOCATION INDICATES THE LOCATION OF THE ROD CONNECTOR ON THE ITEM. SELECT REPLY CODE 10AJ91 CDMSD /D/ 09MATERIAL,HUB HUB MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HUB IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CDMTD /D/ 07RECESS,BUTTON,HORN HORN BUTTON RECESS AN INDICATION OF WHETHER OR NOT A HORN BUTTON RECESS IS INCLUDED. SELECT REPLY CODE 10AA49 CDMWD /D/ 07RECESS,TUBE,STEERING COLUMN STEERING COLUMN TUBE RECESS AN INDICATION OF WHETHER OR NOT A STEERING COLUMN TUBE RECESS IS INCLUDED. SELECT REPLY CODE 10AA49 CDMXD /D/ 07FEATURE,DESIGN,POWER ACTUATION POWER ACTUATION DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A POWER ACTUATION DESIGN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CDMYD /D/ 08LOCATION,END,STEERING ARM SHAFT STEERING ARM SHAFT END LOCATION INDICATES THE LOCATION OF THE STEERING ARM SHAFT END. SELECT REPLY CODE 10AJ91 CDMZD /D/ 07WHEEL,STEERING STEERING WHEEL AN INDICATION OF WHETHER OR NOT A STEERING WHEEL IS INCLUDED. SELECT REPLY CODE 10AA49 CDNBD 18TYPE,END,WHEEL SHAFT WHEEL SHAFT END TYPE INDICATES THE TYPE OF WHEEL SHAFT END. SELECT REPLY CODE 10AB76 CDNCD /D/ 07TUBE,SHAFT,STEERING WHEEL STEERING WHEEL SHAFT TUBE AN INDICATION OF WHETHER OR NOT A STEERING WHEEL SHAFT TUBE IS INCLUDED. SELECT REPLY CODE 10AA49 CDNDJ 04DISTANCE FROM TUBE END TO SHAFT THREADED PORTION DISTANCE FROM TUBE END TO SHAFT THREADED PORTION THE DISTANCE FROM THE TUBE END TO THE THREADED PORTION OF THE SHAFT. 2D AND 1B MODE REPLY21AA051AC20 CDNFD /D/ 07ARM,STEERING STEERING ARM AN INDICATION OF WHETHER OR NOT A STEERING ARM IS INCLUDED. SELECT REPLY CODE 10AA49 CDNGD 05DIRECTION,TURNING,STEERING ARM BALL STEERING ARM BALL TURNING DIRECTION AN INDICATION OF THE DIRECTION THE STEERING ARM BALL IS DESIGNED TO TURN. SELECT REPLY CODE 10AA38 CDNHG /D/ 10TRAVEL IN DEG,MAXIMUM MAXIMUM TRAVEL IN DEG THE MAXIMUM DISTANCE THE ITEM IS DESIGNED TO TRAVEL,EXPRESSED IN DEGREES. FULL TEXT WRITE-IN 0 CDNJJ 04DISTANCE,ARM SHAFT CENTERLINE TO BALL STUD CENTERLINE ARM SHAFT CENTERLINE TO BALL STUD CENTERLINE DISTANCE THE DISTANCE FROM THE CENTERLINE OF THE ARM SHAFT TO THE CENTERLINE OF THE BALL STUD. 2D AND 1B MODE REPLY21AA051AC20 CDNKJ 04DISTANCE,WHEEL SHAFT CENTERLINE TO BALL STUD CENTERLINE WHEEL SHAFT CENTERLINE TO BALL STUD CENTERLINE DISTANCE THE DISTANCE FROM THE CENTERLINE OF THE WHEEL SHAFT TO THE CENTERLINE OF THE BALL STUD. 2D AND 1B MODE REPLY21AA051AC20 CDNLD 18TYPE,END,ARM SHAFT ARM SHAFT END TYPE INDICATES THE TYPE OF ARM SHAFT END. SELECT REPLY CODE 10AB76 CDNMJ 04DIAMETER,MAJOR,ARM SHAFT END ARM SHAFT END MAJOR DIAMETER THE DIAMETER OF THE OUTERMOST SURFACE OF THE ARM SHAFT END. 2D AND 1B MODE REPLY21AA051AC20 CDNNA /D/ 13THREAD SIZE,HOLE,OUTLET MOUNTING OUTLET MOUNTING HOLE THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE OUTLET MOUNTING HOLE. 1A MODE REPLY 0 CDNPA /D/ 13THREAD SIZE,FITTING,OUTLET OUTLET FITTING THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE OUTLET FITTING. 1A MODE REPLY 0 CDNQD /D/ 13THREAD SERIES,FITTING,OUTLET OUTLET FITTING THREAD SERIES A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF AN OUTLET FITTING. SELECT REPLY CODE 10AH06 CDNRD 13THREAD DIRECTION,FITTING,OUTLET OUTLET FITTING THREAD DIRECTION THE DIRECTION OF THE OUTLET FITTING THREAD WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AA38 CDNSD /D/ 13THREAD LOCATION,FITTING,OUTLET OUTLET FITTING THREAD LOCATION THE PORTION OF THE OUTLET FITTING ON WHICH THE THREAD IS LOCATED. SELECT REPLY CODE 10AJ91 CDNTJ 04SIZE ACCOMMODATED,PIPE,NOMINAL,OUTLET OUTLET NOMINAL PIPE SIZE ACCOMMODATED THE DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THAT THE OUTLET WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 CDNWJ /D/ 04DIAMETER ACCOMMODATED,OUTSIDE,OUTLET TUBE OUTLET TUBE OUTSIDE DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTLET TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDNXD /D/ 07CONNECTION,CLEANOUT CLEANOUT CONNECTION AN INDICATION OF WHETHER OR NOT A CLEANOUT CONNECTION IS INCLUDED. SELECT REPLY CODE 10AA49 CDNYD /D/ 07PROVISION,THREAD,CLEANOUT CONNECTION CLEANOUT CONNECTION THREAD PROVISION AN INDICATION OF WHETHER OR NOT A CLEANOUT CONNECTION THREAD PROVISION IS PROVIDED. SELECT REPLY CODE 10AB22 CDNZA /D/ 13THREAD SIZE,CONNECTION,CLEANOUT CLEANOUT CONNECTION THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE CLEANOUT CONNECTION. 1A MODE REPLY 0 CDPBD /D/ 13THREAD SERIES,CONNECTION,CLEANOUT CLEANOUT CONNECTION THREAD SERIES A DESIGNATION INDICATING THE DIAMETER PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF A CLEANOUT CONNECTION. SELECT REPLY CODE 10AH06 CDPCA 19NUMBER,STOCK,NATIONAL,SWITCH SWITCH NATIONAL STOCK NUMBER THE NATIONAL STOCK NUMBER BY WHICH THE SWITCH IS IDENTIFIED. 1A MODE REPLY 0 CDPDA /D/ 19NUMBER,STOCK,NATIONAL,JACK JACK NATIONAL STOCK NUMBER THE NATIONAL STOCK NUMBER BY WHICH THE JACK IS IDENTIFIED. 1A MODE REPLY 0 CDPFA 19NUMBER,STOCK,NATIONAL,CIRCUIT BREAKER CIRCUIT BREAKER NATIONAL STOCK NUMBER THE NATIONAL STOCK NUMBER BY WHICH THE CIRCUIT BREAKER IS IDENTIFIED. 1A MODE REPLY 0 CDPGJ 18TYPE,PRESSURE AND SERVICE,WORKING WORKING PRESSURE AND SERVICE TYPE A MEASUREMENT OF THE WORKING PRESSURE AND THE TYPE OF SERVICE FOR WHICH RATED. 3D AND 1B MODE REPLY32AG671AC203AB75 CDPHJ 18TYPE,TEMP AND SERVICE,WORKING WORKING TEMP AND SERVICE TYPE A MEASUREMENT OF THE WORKING TEMPERATURE AND THE TYPE OF SERVICE FOR WHICH RATED. 3D AND 1B MODE REPLY32AG671AC203AB75 CDPJD 18TYPE,END,OPEN OPEN END TYPE INDICATES THE TYPE OF OPEN END PROVIDED. SELECT REPLY CODE 10AK84 CDPKD /D/ 07HOLE,SECURING,FLANGE FLANGE SECURING HOLE AN INDICATION OF WHETHER OR NOT A FLANGE SECURING HOLE IS INCLUDED. SELECT REPLY CODE 10AA49 CDPLG /D/ 04SPACING,HOLE,SECURING SECURING HOLE SPACING THE SPACING BETWEEN THE SECURING HOLES. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. FULL TEXT WRITE-IN 0 CDPMD 19CHARACTERISTIC,END,FEMALE FEMALE END CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC(S) OF THE FEMALE END. SELECT REPLY CODE 10AH37 CDPNJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,HOLE,SECURING SECURING HOLE THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE SECURING HOLE. 1D AND 1A MODE REPLY12AH06 CDPPD 13THREAD DIRECTION,HOLE,SECURING SECURING HOLE THREAD DIRECTION THE DIRECTION OF THE SECURING HOLE THREAD WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AA38 CDPQG /D/ 08LOCATION,COUNTERBORE/COUNTERSINK COUNTERBORE/COUNTERSINK LOCATION INDICATES THE LOCATION OF THE COUNTERBORE AND/OR COUNTERSINK ON THE ITEM. FULL TEXT WRITE-IN 0 CDPRD /D/ 07HOLE,END,CLOSED CLOSED END HOLE AN INDICATION OF WHETHER OR NOT A HOLE IS INCLUDED IN THE CLOSED END. SELECT REPLY CODE 10AA49 CDPSJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,HOLE HOLE THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE HOLE. 1D AND 1A MODE REPLY12AH06 CDPTD /D/ 07RECESS,CIRCULAR,CLOSED END CLOSED END CIRCULAR RECESS AN INDICATION OF WHETHER OR NOT A CLOSED END CIRCULAR RECESS(ES) IS INCLUDED. SELECT REPLY CODE 10AA49 CDPWJ 04DIAMETER,MAXIMUM,RECESS RECESS MAXIMUM DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST RECESS,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CDPXJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,INLET INLET THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE INLET. PLEASE USE MRC THDS WITH USE OF ISAC FOR INLET IN PLACE OF THIS CANCELED MRC. 1D AND 1A MODE REPLY12AH06 CDPYJ 04DIAMETER,FACILITY,WRENCHING WRENCHING FACILITY DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WRENCHING PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDPZJ 04SIZE,PIPE,NOMINAL,OUTLET OUTLET NOMINAL PIPE SIZE THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE OUTLET PIPE. 1D AND 1B MODE REPLY11AA05 CDQBJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,OUTLET OUTLET THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE OUTLET. PLEASE USE MRC THDS WITH USE OF ISAC FOR OUTLET IN PLACE OF THIS CANCELED MRC. 1D AND 1A MODE REPLY12AH06 CDQCD 18TYPE,CONNECTION,DRAIN HOLE DRAIN HOLE CONNECTION TYPE INDICATES THE TYPE OF DRAIN HOLE CONNECTION PROVIDED. SELECT REPLY CODE 10AB76 CDQDJ 04DIAMETER,CIRCLE,BOLT,DRAIN HOLE FLANGE DRAIN HOLE FLANGE BOLT CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A DRAIN HOLE FLANGE BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDQFA 12QUANTITY,HOLE,DRAIN HOLE FLANGE BOLT DRAIN HOLE FLANGE BOLT HOLE QUANTITY THE NUMBER OF DRAIN HOLE FLANGE BOLT HOLES PROVIDED. 1A MODE REPLY 0 CDQGJ 04DIAMETER,HOLE,BOLT,DRAIN HOLE FLANGE DRAIN HOLE FLANGE BOLT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A DRAIN HOLE FLANGE BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDQHJ /D/ 04DIAMETER,OUTSIDE,FLANGE,DRAIN HOLE DRAIN HOLE FLANGE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A DRAIN HOLE FLANGE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDQJJ 04DISTANCE BETWEEN INLET FACE AND OUTLET FACE CONNECTIONS DISTANCE BETWEEN INLET FACE AND OUTLET FACE CONNECTIONS THE DISTANCE BETWEEN INLET FACE AND OUTLET FACE CONNECTIONS. 2D AND 1B MODE REPLY21AA051AC20 CDQKJ 04WIDTH,HOLE,SLOTTED SLOTTED HOLE WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SLOTTED HOLE, IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CDQLJ /D/ 04DISTANCE BETWEEN INLET AND OUTLET CONNECTION CENTERLINE AND DRAIN CONNECTION FACE DISTANCE BETWEEN INLET AND OUTLET CONNECTION CENTERLINE AND DRAIN CONNECTION FACE THE DISTANCE BETWEEN THE CENTERLINE OF INLET AND OUTLET CONNECTIONS AND FACE OF DRAIN CONNECTION. 2D AND 1B MODE REPLY21AA051AC20 CDQMJ /D/ 04DISTANCE BETWEEN DRAIN CONNECTION CENTERLINE AND OUTLET CONNECTION FACE DISTANCE BETWEEN DRAIN CONNECTION CENTERLINE AND OUTLET CONNECTION FACE THE DISTANCE BETWEEN THE CENTERLINE OF DRAIN CONNECTION AND FACE OF OUTLET CONNECTION. 2D AND 1B MODE REPLY21AA051AC20 CDQND 18TYPE,HOIST HOIST TYPE INDICATES THE TYPE OF HOIST PROVIDED. SELECT REPLY CODE 10AK54 CDQPJ 04HEIGHT,CLEARANCE,INSIDE INSIDE CLEARANCE HEIGHT A MEASUREMENT OF THE INSIDE CLEARANCE HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CDQQJ 04WIDTH,CLEARANCE,INSIDE INSIDE CLEARANCE WIDTH A MEASUREMENT OF THE INSIDE CLEARANCE WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CDQRD /D/ 07CAB,DRIVER,COVERED COVERED DRIVER CAB AN INDICATION OF WHETHER OR NOT A COVERED DRIVER CAB IS INCLUDED. SELECT REPLY CODE 10AA49 CDQSD /D/ 07FEATURE,POWERED,BATTERY BATTERY POWERED FEATURE AN INDICATION OF WHETHER OR NOT A BATTERY POWERED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CDQTD /D/ 18TYPE,PLUG/RECEPTACLE PLUG/RECEPTACLE TYPE INDICATES THE TYPE OF PLUG AND RECEPTACLE UTILIZED BY THE ITEM. SELECT REPLY CODE 10AK12 CDQWD /D/ 07TURNTABLE,FRAME/PLATFORM FRAME/PLATFORM TURNTABLE AN INDICATION OF WHETHER OR NOT A FRAME AND/OR PLATFORM TURNTABLE IS INCLUDED. SELECT REPLY CODE 10AA49 CDQXD /D/ 09MATERIAL,TRAY/PAN TRAY/PAN MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH A TRAY AND/OR PAN IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CDQYJ /D/ 10CAPACITY,TRAY/PAN TRAY/PAN CAPACITY THE CAPACITY OF A PAN AND/OR TRAY. 1D AND 1B MODE REPLY11AB10 CDQZD /D/ 07SIDE,REMOVABLE REMOVABLE SIDE AN INDICATION OF WHETHER OR NOT A REMOVABLE SIDE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CDRBD /D/ 07MOTOR,DRIVE,ELECTRIC ELECTRIC DRIVE MOTOR AN INDICATION OF WHETHER OR NOT AN ELECTRIC DRIVE MOTOR IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 CDRCJ 04DISTANCE,BOOM OUTREACH TO HOOK CENTER BOOM OUTREACH TO HOOK CENTER DISTANCE THE DISTANCE FROM THE BOOM OUTREACH TO THE CENTER OF THE HOOK. 2D AND 1B MODE REPLY21AA051AC20 CDRDD 18TYPE,HANDLING,DRUM DRUM HANDLING TYPE INDICATES THE TYPE OF DRUM HANDLING PROVIDED. SELECT REPLY CODE 10AG25 CDRFJ 04LENGTH,OVERALL,HORIZONTAL ARM HORIZONTAL ARM OVERALL LENGTH THE OVERALL LENGTH OF THE HORIZONTAL ARM. 2D AND 1B MODE REPLY21AA051AC20 CDRGJ 04WIDTH,OVERALL,HORIZONTAL ARM HORIZONTAL ARM OVERALL WIDTH THE OVERALL WIDTH OF THE HORIZONTAL ARM. 2D AND 1B MODE REPLY21AA051AC20 CDRHJ 04THICKNESS,OVERALL,HORIZONTAL ARM HORIZONTAL ARM OVERALL THICKNESS THE OVERALL THICKNESS OF THE HORIZONTAL ARM. 2D AND 1B MODE REPLY21AA051AC20 CDRJJ 04LENGTH,OVERALL,VERTICAL ARM VERTICAL ARM OVERALL LENGTH THE OVERALL LENGTH OF THE VERTICAL ARM. 2D AND 1B MODE REPLY21AA051AC20 CDRKJ 04WIDTH,OVERALL,VERTICAL ARM VERTICAL ARM OVERALL WIDTH THE OVERALL WIDTH OF THE VERTICAL ARM. 2D AND 1B MODE REPLY21AA051AC20 CDRLJ 04THICKNESS,OVERALL,VERTICAL ARM VERTICAL ARM OVERALL THICKNESS THE OVERALL THICKNESS OF THE VERTICAL ARM. 2D AND 1B MODE REPLY21AA051AC20 CDRMG /D/ 19NAME,MANUFACTURER,LIFT TRUCK LIFT TRUCK MANUFACTURER NAME THE NAME OF THE MANUFACTURER OF THE LIFT TRUCK. FULL TEXT WRITE-IN 0 CDRNB 10VOLTAGE IN VOLTS,PRIMARY,TRANSFORMER TRANSFORMER PRIMARY VOLTAGE IN VOLTS THE TOTAL PRIMARY VOLTAGE OF THE TRANSFORMER,EXPRESSED IN VOLTS. 1B MODE REPLY 0 CDRPJ 10FREQUENCY IN HERTZ,TRANSFORMER TRANSFORMER FREQUENCY IN HERTZ THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT OF THE TRANSFORMER. 1D AND 1B MODE REPLY11AC20 CDRQD 10PHASE,TRANSFORMER TRANSFORMER PHASE THE NUMBER OF ALTERNATING CURRENT PHASES OF THE TRANSFORMER. SELECT REPLY CODE 10AD02 CDRRD 18TYPE,CURRENT,ARC ARC CURRENT TYPE INDICATES THE TYPE OF CURRENT OF THE ARC. SELECT REPLY CODE 10AB62 CDRSG 10CURRENT AT SPECIFIED VOLTAGE,MINIMUM MINIMUM CURRENT AT SPECIFIED VOLTAGE THE MINIMUM CURRENT WHICH MUST BE MAINTAINED AT A SPECIFIED VOLTAGE. FULL TEXT WRITE-IN 0 CDRTG 10CURRENT AT SPECIFIED VOLTAGE,MAXIMUM MAXIMUM CURRENT AT SPECIFIED VOLTAGE THE MAXIMUM CURRENT WHICH MUST NOT BE EXCEEDED AT A SPECIFIED VOLTAGE. FULL TEXT WRITE-IN 0 CDRWD /D/ 18TYPE FOR WHICH DESIGNED,OPERATOR OPERATOR TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF OPERATOR FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 CDRXG 13THREAD CHARACTERISTICS THREAD CHARACTERISTICS AN INDICATION OF THE CHARACTERISTICS OF THE THREAD. FULL TEXT WRITE-IN 0 CDRYD /D/ 07DESIGN,CONTROL,REMOTE REMOTE CONTROL DESIGN AN INDICATION OF WHETHER OR NOT A REMOTE CONTROL DESIGN IS INCLUDED. SELECT REPLY CODE 10AA49 CDRZD /D/ 07DESIGN,OUTPUT,AUXILIARY POWER AUXILIARY POWER OUTPUT DESIGN AN INDICATION OF WHETHER OR NOT AN AUXILIARY POWER OUTPUT DESIGN IS INCLUDED. SELECT REPLY CODE 10AA49 CDSBD /D/ 09MATERIAL,LINING,GUN GUN LINING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE GUN LINING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CDSCD /D/ 04ANGLE,HEAD,REVERSIBLE REVERSIBLE HEAD ANGLE AN INDICATION OF WHETHER OR NOT A REVERSIBLE HEAD ANGLE IS INCLUDED. SELECT REPLY CODE 10AA49 CDSDH 11METHOD AND CONTROL TYPE,OPERATION OPERATION METHOD AND CONTROL TYPE THE MEANS USED TO OPERATE THE ITEM AND THE TYPE OF CONTROL PROVIDED. 2D MODE REPLY 23AC583AL37 CDSFB /D/ 10KILOVOLT-AMPERE RATING KILOVOLT-AMPERE RATING THE AMOUNT OF APPARENT POWER,AS DISTINGUISHED FROM TRUE POWER,FOR WHICH THE ITEM IS RATED. 1B MODE REPLY 0 CDSGA 12QUANTITY,STEP,HEAT HEAT STEP QUANTITY THE NUMBER OF SETTINGS PROVIDED TO REGULATE THE HEAT. 1A MODE REPLY 0 CDSHJ 10CLEARANCE,VERTICAL,THROAT MAXIMUM THROAT MAXIMUM VERTICAL CLEARANCE THE MAXIMUM VERTICAL CLEARANCE OF THE THROAT. 1D AND 1B MODE REPLY11AA05 CDSJD /D/ 07ELECTRODE,COOLED,WATER WATER COOLED ELECTRODE AN INDICATION OF WHETHER OR NOT A WATER COOLED ELECTRODE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CDSKJ /D/ 04DIAMETER,OUTSIDE,OVERALL TUBE OVERALL TUBE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CDSLJ /D/ 04DIAMETER,OUTSIDE,TIP END TIP END OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CDSMJ /D/ 04DISTANCE FROM ATTACHMENT END TO BEND DISTANCE FROM ATTACHMENT END TO BEND NONE. 2D AND 1B MODE REPLY21AA051AC20 CDSNJ /D/ 04DIAMETER,INSIDE,ACCOMMODATED TAPE CORE ACCOMMODATED TAPE CORE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TAPE CORE THAT THE ITEM IS DESIGNED TO ACCOMMODATE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDSPD /D/ 09MATERIAL,RULER RULER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE RULER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CDSQD /D/ 07SETSCREW,ADJUSTING ADJUSTING SETSCREW AN INDICATION OF WHETHER OR NOT AN ADJUSTING SETSCREW(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CDSRJ 10CAPACITY,CONTAINER,IMMEDIATE IMMEDIATE CONTAINER CAPACITY THE RATED CAPACITY OF THE IMMEDIATE CONTAINER. 1D AND 1B MODE REPLY12AG67 CDSSD 18TYPE,END,TUBE TUBE END TYPE INDICATES THE TYPE OF TUBE END(S) PROVIDED. SELECT REPLY CODE 10AK54 CDSTD /D/ 07FEATURE,TRACTION,FINGER FINGER TRACTION FEATURE AN INDICATION OF WHETHER OR NOT A FINGER TRACTION FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CDSWJ /D/ 04DISTANCE FROM END TO FLAT DISTANCE FROM END TO FLAT NONE. 2D AND 1B MODE REPLY21AA051AC20 CDSXJ /D/ 04LENGTH,FLAT FLAT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CDSYJ /D/ 04WIDTH,FLAT FLAT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CDSZJ /D/ 04WIDTH,FLAT,FIRST END FIRST END FLAT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CDTBJ /D/ 04WIDTH,FLAT,SECOND END SECOND END FLAT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CDTCJ 04DISTANCE FROM END TO GROOVE DISTANCE FROM END TO GROOVE NONE. 2D AND 1B MODE REPLY21AA051AC20 CDTDD 13THREAD SERIES DESIGNATOR,FACILITY,MOUNTING MOUNTING FACILITY THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A MOUNTING FACILITY DIAMETER. SELECT REPLY CODE 10AH06 CDTFJ 04THREAD DIAMETER,FACILITY,MOUNTING MOUNTING FACILITY THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MOUNTING FACILITY WHICH WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD. 2D AND 1B MODE REPLY21AA051AC20 CDTGA 13THREAD QUANTITY PER INCH,FACILITY,MOUNTING MOUNTING FACILITY THREAD QUANTITY PER INCH THE NUMBER OF THREADS ON THE MOUNTING FACILITY PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CDTHG /D/ 04SIZE ACCOMMODATED ,KEY KEY SIZE ACCOMMODATED NONE. FULL TEXT WRITE-IN 0 CDTJG /D/ 04SIZE ACCOMMODATED/D/,KEY,FIRST END FIRST END KEY SIZE ACCOMMODATED NONE. FULL TEXT WRITE-IN 0 CDTKG /D/ 04SIZE ACCOMMODATED/D/,KEY,SECOND END SECOND END KEY SIZE ACCOMMODATED NONE. FULL TEXT WRITE-IN 0 CDTLJ /D/ 04LENGTH,KEYWAY,FIRST END FIRST END KEYWAY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CDTMJ /D/ 04LENGTH,KEYWAY,SECOND END SECOND END KEYWAY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CDTNJ /D/ 04DISTANCE FROM KEYWAY CENTER TO END DISTANCE FROM KEYWAY CENTER TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 CDTPB /D/ 04ANGLE IN DEG,TAPER,FIRST END FIRST END TAPER ANGLE IN DEG NONE. 1B MODE REPLY 0 CDTQB /D/ 04ANGLE IN DEG,TAPER,SECOND END SECOND END TAPER ANGLE IN DEG NONE. 1B MODE REPLY 0 CDTRJ 04LENGTH,TONGUE,FIRST END FIRST END TONGUE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CDTSJ 04LENGTH,TONGUE,SECOND END SECOND END TONGUE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CDTTJ /D/ 19DIMENSION,END,SQUARE SQUARE END DIMENSION NONE. 2D AND 1B MODE REPLY21AA051AC20 CDTWJ /D/ 19DIMENSION,END,FIRST END SQUARE FIRST END SQUARE END DIMENSION NONE. 2D AND 1B MODE REPLY21AA051AC20 CDTXJ /D/ 19DIMENSION,END,SECOND END SQUARE SECOND END SQUARE END DIMENSION NONE. 2D AND 1B MODE REPLY21AA051AC20 CDTYJ /D/ 04LENGTH,END,SQUARE,FIRST END FIRST END SQUARE END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CDTZJ /D/ 04LENGTH,END,SQUARE,SECOND END SECOND END SQUARE END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CDWBJ 04DISTANCE FROM HOLE CENTER TO END DISTANCE FROM HOLE CENTER TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 CDWCJ /D/ 13THREAD LENGTH,END,FIRST FIRST END THREAD LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CDWDJ /D/ 13THREAD LENGTH,END,SECOND SECOND END THREAD LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CDWFG 13THREAD DESIGNATION,INTERNAL INTERNAL THREAD DESIGNATION NONE. FULL TEXT WRITE-IN 0 CDWGG /D/ 13THREAD DESIGNATION/D/,INTERNAL,FIRST END FIRST END INTERNAL THREAD DESIGNATION/D/ NONE. FULL TEXT WRITE-IN 0 CDWHG /D/ 13THREAD DESIGNATION/D/,INTERNAL,SECOND END SECOND END INTERNAL THREAD DESIGNATION/D/ NONE. FULL TEXT WRITE-IN 0 CDWJG 13THREAD DESIGNATION,EXTERNAL EXTERNAL THREAD DESIGNATION NONE. FULL TEXT WRITE-IN 0 CDWKG /D/ 13THREAD DESIGNATION/D/,EXTERNAL,FIRST END FIRST END EXTERNAL THREAD DESIGNATION/D/ NONE. FULL TEXT WRITE-IN 0 CDWLG /D/ 13THREAD DESIGNATION/D/,EXTERNAL,SECOND END SECOND END EXTERNAL THREAD DESIGNATION/D/ NONE. FULL TEXT WRITE-IN 0 CDWMD /D/ 07HOLE,LUBRICATION,PRESSURE PRESSURE LUBRICATION HOLE AN INDICATION OF WHETHER OR NOT A PRESSURE LUBRICATION HOLE(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CDWNG 19NAME,IDENTIFYING,CIRCULATING PUMP MANUFACTURER CIRCULATING PUMP MANUFACTURER IDENTIFYING NAME THE NAME USED BY THE MANUFACTURER FOR IDENTIFYING THE CIRCULATING PUMP. FULL TEXT WRITE-IN 0 CDWPG /D/ 19NUMBER,IDENTIFYING,CIRCULATING PUMP MANUFACTURER CIRCULATING PUMP MANUFACTURER IDENTIFYING NUMBER THE NUMBER USED BY THE MANUFACTURER FOR IDENTIFYING THE CIRCULATING PUMP. FULL TEXT WRITE-IN 0 CDWQD 18TYPE,SYSTEM,HEATING HEATING SYSTEM TYPE INDICATES THE TYPE OF HEATING SYSTEM INCLUDED IN OR ON THE ITEM. SELECT REPLY CODE 10AB04 CDWRD /D/ 09MATERIAL,MEDIA,WATER SEPARATING WATER SEPARATING MEDIA MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WATER SEPARATING MEDIA IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CDWSA 12QUANTITY,SUMP,ACCUMULATOR ACCUMULATOR SUMP QUANTITY THE NUMBER OF ACCUMULATOR SUMPS PROVIDED. 1A MODE REPLY 0 CDWTD 11METHOD,OPERATION,WATER DISCHARGE,ACCUMULATOR SUMP ACCUMULATOR SUMP WATER DISCHARGE OPERATION METHOD THE MEANS USED TO DISCHARGE WATER FROM THE ACCUMULATOR SUMP. SELECT REPLY CODE 10AC58 CDWWJ A18TYPE AND QUANTITY,ADAPTER ADAPTER TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF ADAPTERS PROVIDED. 1D AND 1A MODE REPLY12AA78 CDWXG /D/ 19NAME,VEHICLE VEHICLE NAME THE NOMENCLATURE BY WHICH THE VEHICLE IS IDENTIFIED. FULL TEXT WRITE-IN 0 CDWYB 10SPEED IN RPM,BOWL,MAXIMUM MAXIMUM BOWL SPEED IN RPM THE MAXIMUM SPEED AT WHICH THE BOWL WILL OPERATE,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 CDWZB 10SPEED IN RPM,MOTOR MOTOR SPEED IN RPM THE SPEED AT WHICH THE MOTOR WILL OPERATE,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 CDXBD 18TYPE,INCLOSURE,MOTOR MOTOR INCLOSURE TYPE INDICATES THE TYPE OF INCLOSURE PROVIDED TO COAT,COVER,PROTECT,OR ENCASE THE MOTOR. SELECT REPLY CODE 10AG85 CDXCD 19POSITION,MOUNTING,MOTOR MOTOR MOUNTING POSITION THE INSTALLED POSITION FOR WHICH THE MOTOR IS DESIGNED. SELECT REPLY CODE 10AM84 CDXDG 19NAME,MANUFACTURER,MOTOR MOTOR MANUFACTURER NAME THE NAME OF THE MANUFACTURER OF THE MOTOR. FULL TEXT WRITE-IN 0 CDXFA 19IDENTIFICATION,FRAME,MOTOR MOTOR FRAME IDENTIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS IDENTIFICATION NUMBER AND/OR SYMBOL USED TO IDENTIFY THE MOTOR FRAME. 1A MODE REPLY 0 CDXGJ A19NUMBER,IDENTIFYING,MOTOR MANUFACTURER MOTOR MANUFACTURER IDENTIFYING NUMBER THE NUMBER USED BY THE MANUFACTURER FOR IDENTIFYING THE MOTOR. 1D AND 1A MODE REPLY12AG99 CDXHG 19CLASSIFICATION,SERVICE,SPECIAL,MOTOR MOTOR SPECIAL SERVICE CLASSIFICATION AN INDICATION OF THE SPECIAL SERVICE CLASSIFICATION OF THE MOTOR. FULL TEXT WRITE-IN 0 CDXJD 18TYPE,INCLOSURE,CONTROL CONTROL INCLOSURE TYPE INDICATES THE TYPE OF INCLOSURE PROVIDED TO COAT,COVER,PROTECT,OR ENCASE THE CONTROL. SELECT REPLY CODE 10AG85 CDXKJ A18TYPE AND QUANTITY,HOLE,MOUNTING MOUNTING HOLE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF MOUNTING HOLES PROVIDED IN OR ON THE ITEM. 1D AND 1A MODE REPLY12AA78 CDXLD /D/ 07RETAINER,ELEMENT,FLUID FILTER FLUID FILTER ELEMENT RETAINER AN INDICATION OF WHETHER OR NOT A FLUID FILTER ELEMENT RETAINER IS INCLUDED. SELECT REPLY CODE 10AA49 CDXMD 18TYPE,PORT,INLET INLET PORT TYPE INDICATES THE TYPE OF INLET PORT PROVIDED. SELECT REPLY CODE 10AH98 CDXNJ /D/T13THREAD PITCH DIAMETER,INLET INLET THREAD PITCH DIAMETER THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF THE INLET STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 CDXPD /D/ 07FEATURE,FACE,RAISED,INLET FLANGE INLET FLANGE RAISED FACE FEATURE AN INDICATION OF WHETHER OR NOT AN INLET FLANGE RAISED FACE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CDXQD 18TYPE,PORT,OUTLET OUTLET PORT TYPE INDICATES THE TYPE OF OUTLET PORT PROVIDED. SELECT REPLY CODE 10AH98 CDXRA 13THREAD CLASS,OUTLET OUTLET THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD. 1A MODE REPLY 0 CDXSJ /D/T13THREAD PITCH DIAMETER,OUTLET OUTLET THREAD PITCH DIAMETER THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF THE OUTLET STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 CDXTB /D/ 04ANGLE IN DEG,SEAT,OUTLET OUTLET SEAT ANGLE IN DEG THE ANGLE OF THE OUTLET END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CDXWJ 04DIAMETER,OUTSIDE,OUTLET FLANGE OUTLET FLANGE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTLET FLANGE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDXXD /D/ 07FEATURE,FACE,RAISED,OUTLET FLANGE OUTLET FLANGE RAISED FACE FEATURE AN INDICATION OF WHETHER OR NOT AN OUTLET FLANGE RAISED FACE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CDXYD /D/ 07VALVE VALVE AN INDICATION OF WHETHER OR NOT A VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 CDXZJ 04DIAMETER,HOLE,BOWL MOUNTING BOWL MOUNTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOWL MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDYBD 11METHOD,MOUNTING,BOWL BOWL MOUNTING METHOD THE MEANS OF ATTACHING THE BOWL. SELECT REPLY CODE 10AM39 CDYCD /D/ 07HOLE,BOLT,MOUNTING MOUNTING BOLT HOLE AN INDICATION OF WHETHER OR NOT A MOUNTING BOLT HOLE(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CDYDD /D/ 07ELEMENT,FILTER FILTER ELEMENT AN INDICATION OF WHETHER OR NOT A FILTER ELEMENT IS INCLUDED. SELECT REPLY CODE 10AA49 CDYFD /D/ 07HOLE,SECURING,FLANGE FLANGE SECURING HOLE AN INDICATION OF WHETHER OR NOT A FLANGE SECURING HOLE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CDYGD 14SHAPE,END,CLOSED CLOSED END SHAPE THE PHYSICAL CONFIGURATION OF THE CLOSED END OF THE ITEM. SELECT REPLY CODE 10AD07 CDYHD /D/ 13THREAD LOCATION,HOLE HOLE THREAD LOCATION THE POSITION(S) OF THE HOLE ON WHICH THE THREAD(S) IS LOCATED. SELECT REPLY CODE 10AJ91 CDYKD /D/ 07RECESS,CIRCULAR,HOLE HOLE CIRCULAR RECESS AN INDICATION OF WHETHER OR NOT A HOLE CIRCULAR RECESS IS INCLUDED. SELECT REPLY CODE 10AA49 CDYLJ /D/ 04DIAMETER,MAXIMUM,HOLE RECESS HOLE RECESS MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE RECESS,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CDYMJ /D/ 04LENGTH,COAT COAT LENGTH A MEASUREMENT TAKEN FROM THE UNDERCOLLAR SEAM AT THE CENTER TO THE BOTTOM EDGE OF THE COAT. 1D AND 1B MODE REPLY11AA05 CDYNG /D/ 19SIGNIFICANCE,DESIGN DESIGN SIGNIFICANCE THE DISTINCTION,QUALIFICATION,OR TITLE SIGNIFIED BY THE DESIGN. FULL TEXT WRITE-IN 0 CDYPD 03DESIGNATION,DEPARTMENT DEPARTMENT DESIGNATION THE MILITARY,CIVILIAN,OR GOVERNMENT DEPARTMENT UTILIZING THE ITEM. SELECT REPLY CODE 10AL31 CDYQD 19RANK FOR WHICH DESIGNED RANK FOR WHICH DESIGNED AN INDICATION OF THE RANK FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL31 CDYRD /D/ 08LOCATION,CONDITION,SURFACE SURFACE CONDITION LOCATION INDICATES THE LOCATION OF AN ITEM TO WHICH A SURFACE CONDITION IS APPLICABLE. SELECT REPLY CODE 10AJ91 CDYSD /D/ 19COUNTRY,AWARDING AWARDING COUNTRY THE NAME OF THE COUNTRY PRESENTING THE AWARD. SELECT REPLY CODE 10AJ50 CDYTD /D/ 03DESIGNATION,WAR WAR DESIGNATION THE NAME OF THE ARMED CONFLICT. SELECT REPLY CODE 10AK54 CDYWJ /D/ 04WIDTH,TOP,OPEN SLEEVE OPEN SLEEVE TOP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SLEEVE TOP WHEN OPEN,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CDYXJ /D/ 04WIDTH,BOTTOM,OPEN SLEEVE OPEN SLEEVE BOTTOM WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SLEEVE BOTTOM WHEN OPEN,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CDYYJ /D/ 04DIAMETER,CORD CORD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CORD,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDYZJ /D/ 04LENGTH,MINIMUM,ROLL ROLL MINIMUM LENGTH THE MINIMUM MEASUREMENT OF THE LONGEST DIMENSION OF THE ROLL,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CDZBD /D/ 07TAB TAB AN INDICATION OF WHETHER OR NOT A TAB IS INCLUDED. SELECT REPLY CODE 10AA49 CDZCJ /D/ 04LENGTH,STRIPE STRIPE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE STRIPE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CDZDJ /D/ 04WIDTH,STRIPE STRIPE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE STRIPE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CDZFH 08LOCATION AND CONSTRUCTION,ATTACHMENT,INTERMEDIATE INTERMEDIATE ATTACHMENT LOCATION AND CONSTRUCTION INDICATES THE LOCATION AND CONSTRUCTION OF THE INTERMEDIATE ATTACHMENTS PROVIDED. 2D MODE REPLY 23AJ911AC06 CDZGH /D/ 18TYPE AND LOCATION,ATTACHMENT ATTACHMENT TYPE AND LOCATION INDICATES THE TYPE AND LOCATION OF THE ATTACHMENT(S) PROVIDED. 2D MODE REPLY 23AJ743AJ91 CDZHA /D/ 12QUANTITY,YEAR,REPRESENTED REPRESENTED YEAR QUANTITY THE NUMBER OF YEARS REPRESENTED BY THE ITEM. 1A MODE REPLY 0 CDZJD /D/ 18TYPE,JEWEL JEWEL TYPE INDICATES THE TYPE OF JEWEL PROVIDED. SELECT REPLY CODE 10AD09 CDZKD /D/ 07NUMBER,SERIAL SERIAL NUMBER AN INDICATION OF WHETHER OR NOT A SERIAL NUMBER IS INCLUDED. SELECT REPLY CODE 10AA49 CDZLD /D/ 09MATERIAL,BACKGROUND BACKGROUND MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BACKGROUND IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CDZMJ /D/A18TYPE AND QUANTITY,INSCRIPTION INSCRIPTION TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF INSCRIPTIONS ON THE ITEM. 1D AND 1A MODE REPLY12AJ03 CDZND /D/ 01COLOR,TRIM,ENAMEL ENAMEL TRIM COLOR THE HUE OR TINT OF THE ENAMEL TRIM. SELECT REPLY CODE 10AD06 CDZPJ /D/ 04DIAMETER,CIRCLE,CIRCUMSCRIBING CIRCUMSCRIBING CIRCLE DIAMETER A MEASUREMENT OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCUMSCRIBING CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CDZQD /D/ 01COLOR,BAND BAND COLOR THE HUE OR TINT OF THE BAND. SELECT REPLY CODE 10AD06 CDZRJ /D/ 04LENGTH,BAND BAND LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BAND,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CDZSA 04SIZE IN LINES SIZE IN LINES A MEASUREMENT OF THE ITEM,EXPRESSED IN LINES. 1A MODE REPLY 0 CDZTD /D/ 18TYPE,EDGE,END END EDGE TYPE INDICATES THE TYPE OF EDGE PROVIDED ON THE END OF THE ITEM. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. SELECT REPLY CODE 10AL25 CDZWD /D/ 18TYPE,EDGE,SIDE SIDE EDGE TYPE INDICATES THE TYPE OF EDGE PROVIDED ON THE SIDE OF THE ITEM. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. SELECT REPLY CODE 10AL25 CDZXD /D/ 07FEATURE,ABRASIVE ABRASIVE FEATURE AN INDICATION OF WHETHER OR NOT AN ABRASIVE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CDZYJ 04WIDTH,CELL CELL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CDZZJ 04LENGTH,CELL CELL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CFBBJ 04THICKNESS AT SIDE,SHELL SHELL THICKNESS AT SIDE NONE. 2D AND 1B MODE REPLY21AA051AC20 CFBCJ /D/ 04THICKNESS AT JAMB/SASH RECESS END,SHELL SHELL THICKNESS AT JAMB/SASH RECESS END NONE. 2D AND 1B MODE REPLY21AA051AC20 CFBDJ /D/ 04THICKNESS AT BOND JOINT END,SHELL SHELL THICKNESS AT BOND JOINT END NONE. 2D AND 1B MODE REPLY21AA051AC20 CFBFJ 04THICKNESS AT EXPOSED CORNER END,SHELL SHELL THICKNESS AT EXPOSED CORNER END NONE. 2D AND 1B MODE REPLY21AA051AC20 CFBGJ /D/ 04WIDTH,RECESS,JAMB/SASH/HEADER/TOP JAMB/SASH/HEADER/TOP RECESS WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CFBHJ /D/ 04DEPTH,RECESS,JAMB/SASH/HEADER/TOP JAMB/SASH/HEADER/TOP RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CFBJJ /D/ 04DEPTH,RECESS,END,OPEN OPEN END RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CFBKJ /D/ 04DISTANCE FROM RECESS CENTER TO CORNER DISTANCE FROM RECESS CENTER TO CORNER NONE. 2D AND 1B MODE REPLY21AA051AC20 CFBLJ /D/ 04WIDTH,OUTLET,CLEANOUT/ELECTRICAL CLEANOUT/ELECTRICAL OUTLET WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CFBMJ /D/ 04HEIGHT,OUTLET,CLEANOUT/ELECTRICAL CLEANOUT/ELECTRICAL OUTLET HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CFBNJ 04DISTANCE,STEERING ARM SHAFT CENTERLINE TO STEERING WHEEL SHAFT END STEERING ARM SHAFT CENTERLINE TO STEERING WHEEL SHAFT END DISTANCE THE DISTANCE FROM THE CENTERLINE OF THE STEERING ARM SHAFT TO THE END OF THE STEERING WHEEL SHAFT. 2D AND 1B MODE REPLY21AA051AC20 CFBPJ 04DISTANCE,STEERING WHEEL SHAFT CENTERLINE TO STEERING ARM SHAFT END STEERING WHEEL SHAFT CENTERLINE TO STEERING ARM SHAFT END DISTANCE THE DISTANCE FROM THE CENTERLINE OF THE STEERING WHEEL SHAFT TO THE END OF THE STEERING ARM SHAFT. 2D AND 1B MODE REPLY21AA051AC20 CFBRJ 04WIDTH,OVERALL,SECTOR SHAFT MOUNTING END SECTOR SHAFT MOUNTING END OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SECTOR SHAFT MOUNTING END,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CFBSJ 04THICKNESS,OVERALL,SECTOR SHAFT MOUNTING END SECTOR SHAFT MOUNTING END OVERALL THICKNESS A MEASUREMENT OF THE SMALLEST OVERALL DIMENSION OF THE SECTOR SHAFT MOUNTING END,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CFBTD /D/ 07BORE,SERRATED,SECTOR SHAFT MOUNTING END SECTOR SHAFT MOUNTING END SERRATED BORE AN INDICATION OF WHETHER OR NOT A SECTOR SHAFT MOUNTING END SERRATED BORE IS INCLUDED. SELECT REPLY CODE 10AA49 CFBWJ 04DIAMETER,MAJOR,SMALL END SMALL END MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE LARGEST CIRCULAR SECTION OF THE SMALL END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFBXG 04ANGLE IN DEG,CUT,TEETH TEETH CUT ANGLE IN DEG THE ANGLE FORMED BY THE TEETH CUT,EXPRESSED IN DEGREES. FULL TEXT WRITE-IN 0 CFBYJ 04DEPTH,TEETH,SMALL END SMALL END TEETH DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE TEETH AT THE SMALL END. 2D AND 1B MODE REPLY21AA051AC20 CFBZD 19CHARACTERISTIC,END,DRAG LINK DRAG LINK END CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC OF THE DRAG LINK END. SELECT REPLY CODE 10AJ88 CFCBJ /D/ 04TAPER PER FOOT,BORE BORE TAPER PER FOOT THE DIMINISHING MEASUREMENT OF THE DIAMETER ALONG THE MAJOR AXIS OF THE BORE,EXPRESSED PER FOOT. 2D AND 1B MODE REPLY21AA051AC20 CFCCJ /D/ 04DISTANCE BETWEEN BALL/BALL STUD HOLE AND SECTOR SHAFT BORE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN BALL/BALL STUD HOLE AND SECTOR SHAFT BORE THE CENTER TO CENTER DISTANCE BETWEEN THE BALL AND/OR BALL STUD HOLE AND THE SECTOR SHAFT BORE. 2D AND 1B MODE REPLY21AA051AC20 CFCDD /D/ 07STUD,BALL BALL STUD AN INDICATION OF WHETHER OR NOT A BALL STUD IS INCLUDED. SELECT REPLY CODE 10AA49 CFCFJ 04DIAMETER,MAJOR,TAPERED BEARING SURFACE TAPERED BEARING SURFACE MAJOR DIAMETER THE DISTANCE ACROSS THE LARGEST CIRCULAR CROSS SECTION OF THE TAPERED BEARING SURFACE. 2D AND 1B MODE REPLY21AA051AC20 CFCGJ 04DISTANCE FROM PIVOT HOLE CENTER TO ROD CONNECTING END DISTANCE FROM PIVOT HOLE CENTER TO ROD CONNECTING END THE DISTANCE FROM THE CENTER OF THE PIVOT HOLE TO THE ROD CONNECTING END. 2D AND 1B MODE REPLY21AA051AC20 CFCHJ 04DIAMETER,SPHERICAL SPHERICAL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SPHERICAL FIGURE OR BODY,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFCJJ 04THICKNESS AT PIVOT HOLE,BODY BODY THICKNESS AT PIVOT HOLE A MEASUREMENT OF THE SMALLEST DIMENSION OF A BODY AT THE PIVOT HOLE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CFCKJ 04HEIGHT AT PIVOT HOLE,BODY BODY HEIGHT AT PIVOT HOLE A MEASUREMENT FROM THE BOTTOM TO THE PIVOT HOLE OF THE BODY,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CFCLD 13THREAD LOCATION,END,ROD CONNECTING ROD CONNECTING END THREAD LOCATION THE PORTION/S/ OF THE ROD CONNECTION END ON WHICH THE THREAD IS LOCATED. SELECT REPLY CODE 10AJ91 CFCMA 13THREAD SIZE,END,ROD CONNECTING ROD CONNECTING END THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE ROD CONNECTING END. 1A MODE REPLY 0 CFCND 13THREAD SERIES DESIGNATOR,END,ROD CONNECTING ROD CONNECTING END THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A DIAMETER OF THE ROD CONNECTING END. SELECT REPLY CODE 10AH06 CFCPD 13THREAD DIRECTION,END,ROD CONNECTING ROD CONNECTING END THREAD DIRECTION THE DIRECTION OF THE ROD CONNECTING END THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 CFCQJ 04THREAD LENGTH,END,ROD CONNECTING ROD CONNECTING END THREAD LENGTH A MEASUREMENT OF THE EXTENT OF COMPLETE (FULL) THREADS ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS OF THE ROD CONNECTING END. 2D AND 1B MODE REPLY21AA051AC20 CFCRA 12QUANTITY,BEND BEND QUANTITY THE NUMBER OF BENDS IN THE ITEM. 1A MODE REPLY 0 CFCSD 18TYPE,ARM,STEERING STEERING ARM TYPE INDICATES THE TYPE OF STEERING ARM. SELECT REPLY CODE 10AK54 CFCTJ 04DISTANCE FROM BALL STUD CENTERLINE TO THREADED END DISTANCE FROM BALL STUD CENTERLINE TO THREADED END THE DISTANCE FROM THE CENTERLINE OF THE BALL STUD TO THE THREADED END. 2D AND 1B MODE REPLY21AA051AC20 CFCWJ 04DISTANCE FROM EYE CENTER TO NEAREST END DISTANCE FROM EYE CENTER TO NEAREST END THE DISTANCE FROM THE CENTER OF THE EYE TO THE NEAREST END. 2D AND 1B MODE REPLY21AA051AC20 CFCXJ /D/ 04DISTANCE FROM ROD/LINK END TO NEAREST EDGE OF OPENING DISTANCE FROM ROD/LINK END TO NEAREST EDGE OF OPENING THE DISTANCE FROM THE ROD AND/OR LINK END TO THE NEAREST EDGE OF THE OPENING. 2D AND 1B MODE REPLY21AA051AC20 CFCYD 14SHAPE,OPENING OPENING SHAPE THE PHYSICAL CONFIGURATION OF THE OPENING. SELECT REPLY CODE 10AD07 CFCZJ 04DIAMETER,LARGEST,OPENING OPENING LARGEST DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CIRCULAR OPENING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFDBD /D/ 07PLUG,SEAT/THREADED,BALL STUD BALL STUD SEAT/THREADED PLUG AN INDICATION OF WHETHER OR NOT A BALL STUD SEAT/S/ AND THREADED PLUG IS INCLUDED. SELECT REPLY CODE 10AA49 CFDCJ 04DISTANCE BETWEEN CONNECTING CENTERS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN CONNECTING CENTERS THE CENTER TO CENTER DISTANCE BETWEEN THE CONNECTING CENTERS. 2D AND 1B MODE REPLY21AA051AC20 CFDDJ 04DISTANCE FROM CONNECTING CENTER TO OPPOSITE END DISTANCE FROM CONNECTING CENTER TO OPPOSITE END THE DISTANCE FROM THE CONNECTING CENTER TO THE OPPOSITE END. 2D AND 1B MODE REPLY21AA051AC20 CFDFD /D/ 07CLAMP,LOCK,ROD END ROD END LOCK CLAMP AN INDICATION OF WHETHER OR NOT A ROD END LOCK CLAMP IS INCLUDED. SELECT REPLY CODE 10AA49 CFDGJ /D/ 04DISTANCE FROM NEAREST END TO GROOVE/SLOT CENTER DISTANCE FROM NEAREST END TO GROOVE/SLOT CENTER THE DISTANCE FROM THE NEAREST END TO THE CENTER OF THE GROOVE AND/OR SLOT. 2D AND 1B MODE REPLY21AA051AC20 CFDHJ /D/ 04DISTANCE BETWEEN GROOVE/SLOT,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN GROOVE/SLOT THE CENTER TO CENTER DISTANCE BETWEEN THE GROOVE AND/OR SLOT. 2D AND 1B MODE REPLY21AA051AC20 CFDJD /D/ 07END,SECURING,THREADED THREADED SECURING END AN INDICATION OF WHETHER OR NOT A THREADED SECURING END IS INCLUDED. SELECT REPLY CODE 10AA49 CFDKD /D/ 07END,SLOTTED,SCREWDRIVER SCREWDRIVER SLOTTED END AN INDICATION OF WHETHER OR NOT A SCREWDRIVER SLOTTED END IS INCLUDED. SELECT REPLY CODE 10AA49 CFDLD /D/ 07HOLE,THREADED,LUBRICATION FITTING LUBRICATION FITTING THREADED HOLE AN INDICATION OF WHETHER OR NOT A LUBRICATION FITTING THREADED HOLE IS INCLUDED. SELECT REPLY CODE 10AA49 CFDMD 18TYPE,GROOVE,LUBRICATION LUBRICATION GROOVE TYPE INDICATES THE TYPE OF LUBRICATION GROOVE PROVIDED. SELECT REPLY CODE 10AK54 CFDND /D/ 05DIRECTION,HOLE,DRILLED DRILLED HOLE DIRECTION AN INDICATION OF THE DIRECTION THE HOLE IS DRILLED. SELECT REPLY CODE 10AJ69 CFDPG /D/ 08LOCATION,FINISH,MICROINCH MICROINCH FINISH LOCATION INDICATES THE LOCATION OF THE MICROINCH FINISH ON THE ITEM. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. FULL TEXT WRITE-IN 0 CFDQJ /D/ 10FINISH RATING,SURFACE,MICROINCH MICROINCH SURFACE FINISH RATING THE SURFACE ROUGHNESS RATING WHICH INDICATES THE AMOUNT OF DEVIATION FROM THE MEANLINE. 1D AND 1B MODE REPLY13AK09 CFDRJ 04ANGLE IN DEG,CHAMFER CHAMFER ANGLE IN DEG NONE. 1D AND 1B MODE REPLY11AC20 CFDSJ /D/ 04LENGTH,OVERALL,LARGEST DIAMETER LARGEST DIAMETER OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CFDTL /D/ 16STYLE,END,STEP STEP END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE STEP END(S). 1L MODE REPLY 0 CFDWL /D/ 16STYLE,END,MAJOR COMPLEMENT MAJOR COMPLEMENT END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE MAJOR DIAMETER END/S/. 1L MODE REPLY 0 CFDXJ /D/ 04DISTANCE BETWEEN KEYWAY CENTERS DISTANCE BETWEEN KEYWAY CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 CFDYB /D/ 04ANGLE IN DEG BETWEEN KEYWAYS ANGLE IN DEG BETWEEN KEYWAYS NONE. 1B MODE REPLY 0 CFDZB /D/ 04ANGLE IN DEG BETWEEN HOLES ANGLE IN DEG BETWEEN HOLES NONE. 1B MODE REPLY 0 CFFBA 13THREAD QUANTITY,WORM WORM THREAD QUANTITY THE NUMBER OF THREADS ON THE WORM. 1A MODE REPLY 0 CFFCJ 13THREAD LEAD,WORM WORM THREAD LEAD THE DISTANCE A WORM THREAD ADVANCES AXIALLY IN ONE COMPLETE TURN. 2D AND 1B MODE REPLY21AA051AC20 CFFDD 13THREAD DIRECTION,WORM WORM THREAD DIRECTION THE DIRECTION OF THE WORM THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 CFFFB 04ANGLE IN DEG,PRESSURE,WORM WORM PRESSURE ANGLE IN DEG THE PRESSURE ANGLE OF THE WORM,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CFFGG 04ANGLE,HELIX,WORM WORM HELIX ANGLE THE ANGULAR AMOUNT THE WORM IS INCLINED. FULL TEXT WRITE-IN 0 CFFHJ 04RADIUS,CURVATURE,CONCAVE WORM THROAT CONCAVE WORM THROAT CURVATURE RADIUS A MEASUREMENT OF THE THROAT CURVATURE RADIUS OF A CONCAVE WORM. 2D AND 1B MODE REPLY21AA051AC20 CFFJJ 04DIAMETER,THROAT,CONCAVE WORM CONCAVE WORM THROAT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CONCAVE WORM THROAT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFFKJ 04DIAMETER,OUTSIDE,WORM WORM OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WORM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFFLJ 04DIAMETER,PITCH,WORM WORM PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF THE WORM. 2D AND 1B MODE REPLY21AA051AC20 CFFMJ 10HARDNESS RATING,SHAFT SHAFT HARDNESS RATING A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF THE SHAFT WHEN USED IN CONJUNCITON WITH A HARDNESS RATING SCALE. 2D AND 1B MODE REPLY22AC261AC20 CFFNJ 04THREAD SECTION LENGTH,WORM WORM THREAD SECTION LENGTH A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS OF THE WORM. 2D AND 1B MODE REPLY21AA051AC20 CFFPJ 04LENGTH,BODY,WORM WORM BODY LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE WORM BODY,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CFFQD /D/ 07END,SURFACE,WORM BODY TAPERED BEARING WORM BODY TAPERED BEARING SURFACE END AN INDICATION OF WHETHER OR NOT THE WORM BODY END/S/ IS PROVIDED WITH A TAPERED BEARING SURFACE. SELECT REPLY CODE 10AB22 CFFRJ 04DIAMETER,LARGEST,TAPERED BEARING SURFACE TAPERED BEARING SURFACE LARGEST DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST TAPERED BEARING SURFACE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFFSJ 04DIAMETER,SMALLEST,TAPERED BEARING SURFACE TAPERED BEARING SURFACE SMALLEST DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST TAPERED BEARING SURFACE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFFTJ 04LENGTH,SURFACE,TAPERED BEARING TAPERED BEARING SURFACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TAPERED BEARING SURFACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CFFWD 08LOCATION,SHAFT SHAFT LOCATION INDICATES THE LOCATION OF THE SHAFT(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 CFFXJ 04LENGTH,UNTHREADED,STRAIGHT STRAIGHT UNTHREADED LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE STRAIGHT UNTHREADED PORTION OF THE ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CFFYJ 04DIAMETER,SECTION,STRAIGHT UNTHREADED STRAIGHT UNTHREADED SECTION DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE STRAIGHT UNTHREADED SECTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFFZJ 04WIDTH,KEYWAY,UNTHREADED SECTION UNTHREADED SECTION KEYWAY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN UNTHREADED SECTION KEYWAY. 2D AND 1B MODE REPLY21AA051AC20 CFGBJ 04DEPTH,KEYWAY,SECTION,UNTHREADED UNTHREADED SECTION KEYWAY DEPTH THE DISTANCE MEASURED ALONG A STRAIGHT LINE FROM THE TOP TO THE INNERMOST POINT OF THE UNTHREADED SECTION OF THE KEYWAY. 2D AND 1B MODE REPLY21AA051AC20 CFGCJ 04DIAMETER,HOLE,UNTHREADED SECTION PIN UNTHREADED SECTION PIN HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE UNTHREADED SECTION PIN HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFGDJ 04DIAMETER,LARGEST,TAPER TAPER LARGEST DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST PORTION OF THE TAPER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFGFJ 04DIAMETER,HOLE,TAPERED SECTION PIN TAPERED SECTION PIN HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TAPERED SECTION PIN HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFGGJ 04WIDTH,KEYWAY,TAPERED SECTION TAPERED SECTION KEYWAY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TAPERED SECTION KEYWAY. 2D AND 1B MODE REPLY21AA051AC20 CFGHJ 04DEPTH,KEYWAY,TAPERED SECTION TAPERED SECTION KEYWAY DEPTH THE DISTANCE MEASURED ALONG A STRAIGHT LINE FROM THE TOP TO THE INNERMOST POINT OF THE TAPERED SECTION OF THE KEYWAY. 2D AND 1B MODE REPLY21AA051AC20 CFGJA 12QUANTITY,SPLINE,INVOLUTE INVOLUTE SPLINE QUANTITY THE NUMBER OF INVOLUTE SPLINES ON THE ITEM. 1A MODE REPLY 0 CFGKB 04ANGLE IN DEG,PRESSURE,INVOLUTE SPLINE INVOLUTE SPLINE PRESSURE ANGLE IN DEG THE PRESSURE ANGLE OF THE INVOLUTE SPLINE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CFGLJ 04DIAMETER,PITCH,INVOLUTE SPLINE INVOLUTE SPLINE PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF THE INVOLUTE SPLINE. 2D AND 1B MODE REPLY21AA051AC20 CFGMJ 04LENGTH,SPLINE,INVOLUTE INVOLUTE SPLINE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE INVOLUTE SPLINE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CFGND /D/ 07FEATURE,IMPREGNATED,LUBRICANT LUBRICANT IMPREGNATED FEATURE AN INDICATION OF WHETHER OR NOT A LUBRICANT IMPREGNATED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CFGPD 19CHARACTERISTIC,END,BALL SEAT BALL SEAT END CHARACTERISTIC INDICATES THE PHYSICAL CHARACTERISTIC(S) OF THE BALL SEAT END. SELECT REPLY CODE 10AK54 CFGQD 14SHAPE,CROSS-SECTIONAL,FIRST END FIRST END CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE FIRST END WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 CFGRA 12QUANTITY,TEETH,FIRST END FIRST END TEETH QUANTITY THE NUMBER OF TEETH PROVIDED AT THE FIRST END. 1A MODE REPLY 0 CFGSJ 04LENGTH,SERRATION,FIRST END FIRST END SERRATION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SERRATION AT THE FIRST END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CFGTJ 04DIAMETER,MAJOR,FIRST END FIRST END MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTERMOST SURFACE OF THE FIRST END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFGWB 04ANGLE IN DEG,PRESSURE,FIRST END FIRST END PRESSURE ANGLE IN DEG THE PRESSURE ANGLE OF THE FIRST END,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CFGXD 14SHAPE,CROSS-SECTIONAL,SECOND END SECOND END CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE SECOND END WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 CFGYA 12QUANTITY,TEETH,SECOND END SECOND END TEETH QUANTITY THE NUMBER OF TEETH PROVIDED AT THE SECOND END. 1A MODE REPLY 0 CFGZJ 04LENGTH,SERRATION,SECOND END SECOND END SERRATION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF SERRATION AT THE SECOND END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CFHBJ 04DIAMETER,MAJOR,SECOND END SECOND END MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTERMOST SURFACE OF THE SECOND END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFHCB 04ANGLE IN DEG,PRESSURE,SECOND END SECOND END PRESSURE ANGLE IN DEG THE PRESSURE ANGLE OF THE SECOND END,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CFHDJ /D/ 04WIDTH ACROSS FLATS,END,SECOND SECOND END WIDTH ACROSS FLATS THE DISTANCE FROM ONE FLAT TO THE OPPOSITE FLAT OF THE SECOND END. 2D AND 1B MODE REPLY21AA051AC20 CFHFD /D/ 19CHARACTERISTIC AT FIRST END,END,SOLID BAR SOLID BAR END CHARACTERISTIC AT FIRST END INDICATES THE PHYSICAL CHARACTERISTIC OF THE END OF THE SOLID BAR AT THE FIRST END. SELECT REPLY CODE 10AB76 CFHGD /D/ 19CHARACTERISTIC AT SECOND END,END,SOLID BAR SOLID BAR END CHARACTERISTIC AT SECOND END INDICATES THE PHYSICAL CHARACTERISTIC OF THE END OF THE SOLID BAR AT THE SECOND END. SELECT REPLY CODE 10AB76 CFHHJ 04THREAD DIAMETER,CONNECTOR CONNECTOR THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE CONNECTOR, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFHJA /D/ 13THREAD QUANTITY PER INCH,CONNECTION CONNECTION THREAD QUANTITY PER INCH THE NUMBER OF THREADS ON THE CONNECTION PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CFHKA 13SCREW THREAD QUANTITY PER INCH SCREW THREAD QUANTITY PER INCH THE NUMBER OF SCREW THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CFHLD 13THREAD CLASS THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH-DIAMETER TOLERANCE AND THE EXTERNAL OR INTERNAL LOCATION OF THE THREAD. SELECT REPLY CODE 10AN53 CFHMJ 04DIAMETER,OUTSIDE,COVER COVER OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COVER,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFHNJ 04LENGTH,OVERALL,COVER COVER OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE COVER. 2D AND 1B MODE REPLY21AA051AC20 CFHPJ 04LENGTH,LARGEST,BAR END TO COVER BAR END TO COVER LARGEST LENGTH A MEASUREMENT OF THE LARGEST DIMENSION FROM THE END OF THE BAR TO THE COVER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CFHQJ 04DIAMETER,NOMINAL,TIRE RIM TIRE RIM NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TIRE RIM,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CFHRD /D/ 07TIRE TIRE AN INDICATION OF WHETHER OR NOT A TIRE IS INCLUDED. SELECT REPLY CODE 10AA49 CFHSD 18TYPE,FACE,MOUNTING MOUNTING FACE TYPE INDICATES THE TYPE OF MOUNTING FACE. SELECT REPLY CODE 10AG89 CFHTJ 04DISTANCE FROM RIM CENTERLINE TO OUTSIDE WHEEL MOUNTING FACE,OFFSET OFFSET DISTANCE FROM RIM CENTERLINE TO OUTSIDE WHEEL MOUNTING FACE THE OFFSET DISTANCE FROM THE CENTERLINE OF THE RIM TO THE OUTSIDE OF THE WHEEL MOUNTING FACE. 2D AND 1B MODE REPLY21AA051AC20 CFHWD /D/ 07FEATURE,MOUNTING,HUB CAP HUB CAP MOUNTING FEATURE AN INDICATION OF WHETHER OR NOT A HUB CAP MOUNTING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CFHXD /D/ 07CAP,HUB HUB CAP AN INDICATION OF WHETHER OR NOT A HUB CAP IS INCLUDED.PLEASE USE MRC ABFF FOR NIINS WERE ANSWERED WITH "INCLUDED"IN PLACE OF THIS CANCELLED MRC. SELECT REPLY CODE 10AA49 CFHYA /D/ 16STYLE,RIM RIM STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE RIM. 1A MODE REPLY 0 CFHZJ /D/ 04DIAMETER,OUTSIDE,WHEEL/SPIDER WHEEL/SPIDER OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WHEEL AND/OR SPIDER,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.PLEASE USE MRC ABKVWITH ISAC CODING OF RIM,OVERAL AND TIRE IN PLACE OF THIS CANCELLED MRC. 2D AND 1B MODE REPLY21AA051AC20 CFJBJ 04WIDTH AT OUTSIDE DIAMETER,WHEEL WHEEL WIDTH AT OUTSIDE DIAMETER THE WIDTH OF THE WHEEL AT THE OUTSIDE DIAMETER. 2D AND 1B MODE REPLY21AA051AC20 CFJCD /D/ 07FACILITY,THREADED,RIM FASTENING RIM FASTENING THREADED FACILITY AN INDICATION OF WHETHER OR NOT A RIM FASTENING THREADED FACILITY(IES) IS INCLUDED.PLEASE USE MRC ABFF FOR NIINS WERE ANSWERED WITH "INCLUDED" IN PLACE OF THIS CANCELLED MRC. SELECT REPLY CODE 10AA49 CFJDD 19FACILITY,FASTENING,RIM RIM FASTENING FACILITY THE FACILITY FOR WHICH THE RIM IS FASTENED. SELECT REPLY CODE 10AM39 CFJFD /D/ 18TYPE FOR WHICH DESIGNED,RING RING TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF RING FOR WHICH THE ITEM IS DESIGNED. PLEASE USE MRC ALQF IN PLACE OF THIS CANCELLED MRC. SELECT REPLY CODE 10AK54 CFJGD /D/ 07FACILITY,MOUNTING,BOLT/STUD BOLT/STUD MOUNTING FACILITY AN INDICATION OF WHETHER OR NOT A BOLT AND/OR STUD MOUNTING FACILITY IS INCLUDED. PLEASE USE MRC CBBL IN PLACE OF THIS CANCELLED MRC. SELECT REPLY CODE 10AA49 CFJHD 19CHARACTERISTIC,HUB HUB CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC OF THE HUB. SELECT REPLY CODE 10AJ88 CFJJA /D/ 16STYLE,HUB HUB STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HUB. 1A MODE REPLY 0 CFJKD 19CHARACTERISTIC,RIM RIM CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC OF THE RIM. SELECT REPLY CODE 10AJ88 CFJLD 18TYPE,RIM,DEMOUNTABLE DEMOUNTABLE RIM TYPE INDICATES THE TYPE OF DEMOUNTABLE RIM PROVIDED. SELECT REPLY CODE 10AK54 CFJMD 18TYPE,RIM,INTEGRAL INTEGRAL RIM TYPE INDICATES THE TYPE OF INTEGRAL RIM PROVIDED. SELECT REPLY CODE 10AK54 CFJND /D/ 11METHOD,CLOSING/SUPPORTING,TROUSERS WAIST TROUSERS WAIST CLOSING/SUPPORTING METHOD THE MEANS BY WHICH THE OPENING IS CLOSED AND/OR SUPPORTED AT THE WAIST OF THE TROUSERS. SELECT REPLY CODE 10AF69 CFJPD /D/ 01COLOR,BELT BELT COLOR THE HUE OR TINT OF THE BELT. SELECT REPLY CODE 10AD06 CFJQD /D/ 09MATERIAL,SURFACE,OUTER,ELBOW/KNEE PAD ELBOW/KNEE PAD OUTER SURFACE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE OUTER SURFACE OF THE ELBOW AND/OR KNEE PAD IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CFJRD /D/ 02DESIGN,JUMPER JUMPER DESIGN THE DESIGN OF THE JUMPER EXCLUDING THE SLEEVES,CUFFS,COLLAR,AND THE LIKE. SELECT REPLY CODE 10AK54 CFJSD /D/ 07WAIST,ELASTIC,JUMPER JUMPER ELASTIC WAIST AN INDICATION OF WHETHER OR NOT A JUMPER ELASTIC WAIST IS INCLUDED. SELECT REPLY CODE 10AA49 CFJTD /D/ 11METHOD,CLOSURE,BODY BODY CLOSURE METHOD THE MEANS BY WHICH THE BODY OPENING IS CLOSED. SELECT REPLY CODE 10AF69 CFJWD /D/ 08LOCATION,DEVICE,CLOSING,BODY BODY CLOSING DEVICE LOCATION INDICATES THE LOCATION OF THE CLOSING DEVICE IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 CFJXA /D/ 12QUANTITY,CLOSURE,LEG LEG CLOSURE QUANTITY THE NUMBER OF CLOSURES INCLUDED ON THE LEG PORTION OF AN ITEM. 1A MODE REPLY 0 CFJYD /D/ 11METHOD,CLOSING,LEG LEG CLOSING METHOD THE MEANS BY WHICH THE LEG PORTION IS CLOSED. SELECT REPLY CODE 10AF69 CFJZD /D/ 08LOCATION,DEVICE,CLOSING,LEG LEG CLOSING DEVICE LOCATION INDICATES THE LOCATION OF THE LEG CLOSING DEVICE ON THE GARMENT. SELECT REPLY CODE 10AJ91 CFKBD /D/ 07STRAP,ANKLE ANKLE STRAP AN INDICATION OF WHETHER OR NOT AN ANKLE STRAP IS INCLUDED. SELECT REPLY CODE 10AA49 CFKCD /D/ 07STRAP,CUFF,WRIST WRIST CUFF STRAP AN INDICATION OF WHETHER OR NOT A WRIST CUFF STRAP IS INCLUDED. SELECT REPLY CODE 10AA49 CFKDD /D/ 07FEATURE,FREE,LINT/STATIC LINT/STATIC FREE FEATURE AN INDICATION OF WHETHER OR NOT A LINT AND/OR STATIC FREE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CFKFD /D/ 11METHOD,CLOSING,WRIST WRIST CLOSING METHOD THE MEANS BY WHICH THE WRIST OPENING IS CLOSED. SELECT REPLY CODE 10AF69 CFKGD /D/ 07PASS-THROUGHS,POCKET,SIDE SIDE POCKET PASS-THROUGHS AN INDICATION OF WHETHER OR NOT SIDE POCKET PASS-THROUGHS ARE INCLUDED. SELECT REPLY CODE 10AA49 CFKHD 18TYPE,BELT BELT TYPE INDICATES THE TYPE OF BELT PROVIDED. SELECT REPLY CODE 10AK54 CFKJD /D/ 07DRAWCORD,WAIST WAIST DRAWCORD AN INDICATION OF WHETHER OR NOT A WAIST DRAWCORD IS INCLUDED. SELECT REPLY CODE 10AA49 CFKKD /D/ 07DETACHABILITY DETACHABILITY AN INDICATION OF WHETHER OR NOT AN ITEM IS DETACHABLE. SELECT REPLY CODE 10AH97 CFKLD /D/ 11METHOD,CLOSING,FACE APERTURE FACE APERTURE CLOSING METHOD THE MEANS BY WHICH THE FACE APERTURE IS CLOSED. SELECT REPLY CODE 10AF69 CFKMD /D/ 11METHOD,ADJUSTMENT,ANKLE ANKLE ADJUSTMENT METHOD THE MEANS USED TO ADJUST AN ITEM AT THE ANKLE(S). SELECT REPLY CODE 10AM39 CFKNA /D/ 12QUANTITY,BUCKLE BUCKLE QUANTITY THE NUMBER OF BUCKLES INCLUDED. 1A MODE REPLY 0 CFKPD /D/ 07MITTENS,ATTACHED ATTACHED MITTENS AN INDICATION OF WHETHER OR NOT ATTACHED MITTENS ARE INCLUDED. SELECT REPLY CODE 10AA49 CFKQD /D/ 07SOCKS,ATTACHED ATTACHED SOCKS AN INDICATION OF WHETHER OR NOT ATTACHED SOCKS ARE INCLUDED. SELECT REPLY CODE 10AA49 CFKRD /D/ 07MARKER,DYE,SEA SEA DYE MARKER AN INDICATION OF WHETHER OR NOT A SEA DYE MARKER IS INCLUDED. SELECT REPLY CODE 10AA49 CFKSA /D/ 12QUANTITY,APERTURE,HOSE HOSE APERTURE QUANTITY THE NUMBER OF HOSE APERTURES INCLUDED. 1A MODE REPLY 0 CFKTD /D/ 08LOCATION,APERTURE,HOSE HOSE APERTURE LOCATION INDICATES THE LOCATION OF THE ITEM THAT CONTAINS THE HOSE APERTURE(S). SELECT REPLY CODE 10AJ91 CFKWD /D/ 09MATERIAL,CUFF,GARMENT GARMENT CUFF MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CUFF(S) OF A GARMENT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CFKXD /D/ 07GLOVES,ATTACHED ATTACHED GLOVES AN INDICATION OF WHETHER OR NOT ATTACHED GLOVES ARE INCLUDED. SELECT REPLY CODE 10AA49 CFKYD /D/ 08LOCATION,CHAMBER,BUOYANCY BUOYANCY CHAMBER LOCATION INDICATES THE LOCATION OF THE BUOYANCY CHAMBER(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 CFKZD /D/ 02DESIGN,JACKET JACKET DESIGN THE DESIGN OF THE BODY OF THE JACKET EXCLUDING THE SLEEVES,CUFFS,COLLAR,AND THE LIKE. SELECT REPLY CODE 10AK54 CFLBD /D/ 11METHOD,CLOSING,JACKET JACKET CLOSING METHOD THE MEANS BY WHICH THE PRINCIPAL OPENING OF THE JACKET IS CLOSED. SELECT REPLY CODE 10AF69 CFLCD /D/ 08LOCATION,DEVICE,CLOSING,JACKET JACKET CLOSING DEVICE LOCATION INDICATES THE LOCATION OF THE CLOSING DEVICE ON THE JACKET. SELECT REPLY CODE 10AJ91 CFLDD /D/ 07SLEEVES,LENGTH,FULL FULL LENGTH SLEEVES AN INDICATION OF WHETHER OR NOT FULL LENGTH SLEEVES ARE INCLUDED. SELECT REPLY CODE 10AA49 CFLFD /D/ 07SUSPENDERS,ATTACHED,TROUSERS TROUSERS ATTACHED SUSPENDERS AN INDICATION OF WHETHER OR NOT ATTACHED SUSPENDERS ARE INCLUDED ON THE TROUSERS. SELECT REPLY CODE 10AA49 CFLGD /D/ 07STRAP/BUCKLE,ADJUSTMENT,WAIST WAIST ADJUSTMENT STRAP/BUCKLE AN INDICATION OF WHETHER OR NOT A WAIST ADJUSTMENT STRAP(S) AND/OR BUCKLE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CFLHD /D/ 07TAPE,TIE,LEG BOTTOM LEG BOTTOM TIE TAPE AN INDICATION OF WHETHER OR NOT A LEG BOTTOM TIE TAPE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CFLJD 18TYPE FOR WHICH DESIGNED,PROTECTION PROTECTION TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF PROTECTION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AF34 CFLKD /D/ 07FEET FEET AN INDICATION OF WHETHER OR NOT FEET ARE INCLUDED. SELECT REPLY CODE 10AA49 CFLLD 04LENGTH,LEG,GARMENT GARMENT LEG LENGTH THE LENGTH OF THE LEG WITH REFERENCE TO THE PART OF THE BODY THE GARMENT REACHES. SELECT REPLY CODE 10AF68 CFLMD /D/ 09MATERIAL,LINING,JACKET JACKET LINING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE JACKET LINING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CFLNJ 04DISTANCE ACROSS ARMS,BILL TO BILL BILL TO BILL DISTANCE ACROSS ARMS NONE. 2D AND 1B MODE REPLY21AA051AC20 CFLPJ 04LENGTH FROM STOCK CENTERLINE TO SHACKLE PIN HOLE CENTERLINE,SHANK SHANK LENGTH FROM STOCK CENTERLINE TO SHACKLE PIN HOLE CENTERLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 CFLQJ 04LENGTH FROM STOCK CENTERLINE TO TIP,FLUKE FLUKE LENGTH FROM STOCK CENTERLINE TO TIP NONE. 2D AND 1B MODE REPLY21AA051AC20 CFLRJ 04LENGTH FROM CROWN FLAT BASE TO SHACKLE PIN HOLE CENTERLINE,SHANK SHANK LENGTH FROM CROWN FLAT BASE TO SHACKLE PIN HOLE CENTERLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 CFLSJ 04WIDTH ACROSS FLUKES,OVERALL OVERALL WIDTH ACROSS FLUKES NONE. 2D AND 1B MODE REPLY21AA051AC20 CFLTJ 04LENGTH FROM CROWN FLAT BASE TO TIP,FLUKE FLUKE LENGTH FROM CROWN FLAT BASE TO TIP NONE. 2D AND 1B MODE REPLY21AA051AC20 CFLWJ 04WIDTH ACROSS STABILIZER,OVERALL OVERALL WIDTH ACROSS STABILIZER NONE. 2D AND 1B MODE REPLY21AA051AC20 CFLXJ /D/ 04LENGTH BETWEEN SHACKLE PIN CENTERLINE AND PELICAN HOOK CENTERLINE,MAXIMUM MAXIMUM LENGTH BETWEEN SHACKLE PIN CENTERLINE AND PELICAN HOOK CENTERLINE THE MAXIMUM DISTANCE MEASURED FROM THE CENTERLINE OF THE SHACKLE PIN TO THE CENTERLINE OF THE PELICAN HOOK. 1D AND 1B MODE REPLY11AA05 CFLYJ 10SPREAD,OVERALL,PRONGS PRONGS OVERALL SPREAD A MEASUREMENT OF A STRAIGHT LINE EXTENDING BETWEEN BOUNDARIES OF THE AREA COVERED BY THE PRONGS. 2D AND 1B MODE REPLY21AA051AC20 CFLZJ 04DIAMETER,INSIDE,SHANK TOP EYE SHANK TOP EYE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SHANK TOP EYE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFMBD 02DESIGN,FLUKE FLUKE DESIGN THE DESIGN OF THE FLUKE. SELECT REPLY CODE 10AD07 CFMCD 02DESIGN,STOCK STOCK DESIGN THE DESIGN OF THE STOCK. SELECT REPLY CODE 10AD07 CFMDJ 10SIZE,THIMBLE,SHANK EYE SHANK EYE THIMBLE SIZE DESIGNATES THE SIZE OF THE THIMBLE IN THE EYE OF THE SHANK. 2D AND 1B MODE REPLY21AA051AC20 CFMFJ 04DIAMETER,INSIDE,SHANK BASE EYE SHANK BASE EYE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SHANK BASE EYE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFMGD /D/ 07SHACKLE SHACKLE AN INDICATION OF WHETHER OR NOT A SHACKLE IS INCLUDED ON THE ITEM. SELECT REPLY CODE 10AA49 CFMHD /D/ 07HOLE,FLUKE FLUKE HOLE AN INDICATION OF WHETHER OR NOT A HOLE(S) IS INCLUDED IN THE FLUKE(S). SELECT REPLY CODE 10AA49 CFMJD /D/ 07BAND,BALANCING BALANCING BAND AN INDICATION OF WHETHER OR NOT A BALANCING BAND IS INCLUDED. SELECT REPLY CODE 10AA49 CFMKA 12QUANTITY,POST POST QUANTITY THE NUMBER OF POSTS INCLUDED. 1A MODE REPLY 0 CFMLJ 04DISTANCE BETWEEN POSTS DISTANCE BETWEEN POSTS THE DISTANCE BETWEEN THE POSTS. 2D AND 1B MODE REPLY21AA051AC20 CFMMD 14SHAPE,CAP CAP SHAPE THE PHYSICAL CONFIGURATION OF THE CAP. SELECT REPLY CODE 10AD07 CFMNJ 04DISTANCE FROM POST TO LIP OUTSIDE DISTANCE FROM POST TO LIP OUTSIDE THE DISTANCE FROM THE POST TO THE OUTSIDE OF THE LIP. 2D AND 1B MODE REPLY21AA051AC20 CFMPJ 04DISTANCE FROM POST TOP TO DECK DISTANCE FROM POST TOP TO DECK THE DISTANCE FROM THE TOP OF THE POST TO THE DECK. 2D AND 1B MODE REPLY21AA051AC20 CFMQD 14SHAPE,POST POST SHAPE THE PHYSICAL CONFIGURATION OF THE POST. SELECT REPLY CODE 10AD07 CFMRJ 04WIDTH ACROSS FLATS,OUTSIDE OUTSIDE WIDTH ACROSS FLATS A MEASUREMENT OF THE OUTSIDE DISTANCE FROM ONE FLAT TO THE OPPOSITE FLAT. 2D AND 1B MODE REPLY21AA051AC20 CFMSD /D/ 07CROSSARM CROSSARM AN INDICATION OF WHETHER OR NOT A CROSSARM IS INCLUDED. SELECT REPLY CODE 10AA49 CFMTD /D/ 09MATERIAL,CROSSARM CROSSARM MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CROSSARM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CFMWJ 04DIAMETER,OUTSIDE,CROSSARM CROSSARM OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CROSSARM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFMXJ 04DISTANCE FROM BASE TOP TO CROSSARM CENTERLINE DISTANCE FROM BASE TOP TO CROSSARM CENTERLINE THE DISTANCE FROM THE TOP OF THE BASE TO THE CROSSARM CENTERLINE. 2D AND 1B MODE REPLY21AA051AC20 CFMYJ 04DIAMETER,INSIDE,CROSSARM CROSSARM INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CROSSARM,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFMZD 14SHAPE,CROSS-SECTIONAL,HORIZONTAL HORIZONTAL CROSS-SECTIONAL SHAPE THE PHYSICAL CONFIGURATION OF THE ITEM VIEWED IN A HORIZONTAL POSITION. SELECT REPLY CODE 10AD07 CFNBD 02DESIGN,SIDE SIDE DESIGN THE DESIGN OF THE SIDE(S). SELECT REPLY CODE 10AK54 CFNCJ /D/ 04WIDTH,FACE,TOP TOP FACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TOP FACE OF THE ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CFNDJ /D/ 04LENGTH,OVERALL,TOP FACE TOP FACE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE TOP FACE. 2D AND 1B MODE REPLY21AA051AC20 CFNFD 18TYPE,CONNECTION,CHAIN ASSEMBLY ATTACHMENT CHAIN ASSEMBLY ATTACHMENT CONNECTION TYPE INDICATES THE TYPE OF CONNECTION FOR ATTACHING THE CHAIN ASSEMBLY. SELECT REPLY CODE 10AA78 CFNGJ /D/ 04DIAMETER,CONNECTION,ATTACHMENT,CHAIN ASSEMBLY CHAIN ASSEMBLY ATTACHMENT CONNECTION DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CONNECTION IN THE ITEM TO WHICH THE CHAIN ASSEMBLY ATTACHMENT IS CONNECTED,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFNHJ 04THICKNESS FOR WHICH DESIGNED,RAIL,MOUNTING MOUNTING RAIL THICKNESS FOR WHICH DESIGNED A MEASUREMENT OF THE SMALLEST DIMENSION OF THE MOUNTING RAIL FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CFNJJ 04DIAMETER ACCOMMODATED,ROPE,MAXIMUM MAXIMUM ROPE DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE ROPE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CFNKJ 04DIAMETER,CENTER CENTER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ITEM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFNLJ 04SIZE FOR WHICH DESIGNED,CHAIN,STUD LINK STUD LINK CHAIN SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE STUD LINK CHAIN FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 CFNMJ /D/ 04SIZE FOR WHICH DESIGNED,CHAIN,ANCHOR ANCHOR CHAIN SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF ANCHOR CHAIN FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 CFNND 18TYPE FOR WHICH DESIGNED,SERVICE SERVICE TYPE FOR WHICH DESIGNED INDICATES THE SERVICE TYPE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AB75 CFNPA 12QUANTITY,BAFFLE,SELF-CONTAINED SELF-CONTAINED BAFFLE QUANTITY THE NUMBER OF SELF-CONTAINED BAFFLES PROVIDED. 1A MODE REPLY 0 CFNQJ 04DISTANCE BETWEEN INLET CENTERLINE AND OUTLET FACE DISTANCE BETWEEN INLET CENTERLINE AND OUTLET FACE THE DISTANCE BETWEEN THE CENTERLINE OF THE INLET AND THE FACE OF THE OUTLET. 2D AND 1B MODE REPLY21AA051AC20 CFNRJ /D/ 04DISTANCE BETWEEN OUTLET CENTERLINE AND INLET FACE DISTANCE BETWEEN OUTLET CENTERLINE AND INLET FACE THE DISTANCE BETWEEN THE CENTERLINE OF THE OUTLET AND THE FACE OF THE INLET. 2D AND 1B MODE REPLY21AA051AC20 CFNSJ /D/ 04DISTANCE BETWEEN HORIZONTAL CONNECTION CENTERLINE AND BOTTOM OF DRAIN CONNECTION DISTANCE BETWEEN HORIZONTAL CONNECTION CENTERLINE AND BOTTOM OF DRAIN CONNECTION THE DISTANCE BETWEEN THE CENTERLINE OF THE HORIZONTAL CONNECTION AND THE BOTTOM OF THE DRAIN CONNECTION. 2D AND 1B MODE REPLY21AA051AC20 CFNTJ 04DEPTH,COUNTERBORE,FIRST FIRST COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CFNWD 14SHAPE,HEAD,UPPER SECTION UPPER SECTION HEAD SHAPE THE PHYSICAL CONFIGURATION OF THE UPPER SECTION HEAD. SELECT REPLY CODE 10AD07 CFNXD 07PROVISION,THREAD,UPPER SECTION HEAD UPPER SECTION HEAD THREAD PROVISION AN INDICATION OF WHETHER OR NOT THE UPPER SECTION HEAD IS THREADED. SELECT REPLY CODE 10AE00 CFNYD /D/ 07SECTION,EXTENSION EXTENSION SECTION AN INDICATION OF WHETHER OR NOT AN EXTENSION SECTION IS INCLUDED. SELECT REPLY CODE 10AA49 CFNZD /D/ 18TYPE,SECTION,EXTENSION EXTENSION SECTION TYPE INDICATES THE TYPE OF EXTENSION SECTION PROVIDED. SELECT REPLY CODE 10AK95 CFPBJ /D/ 04LENGTH,SECTION,EXTENSION EXTENSION SECTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE EXTENSION SECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CFPCA /D/ 16STYLE,BASE,LOWER SECTION LOWER SECTION BASE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LOWER SECTION BASE. 1A MODE REPLY 0 CFPDA /D/ 16STYLE,BASE,ADDITIONAL ADDITIONAL BASE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ADDITIONAL BASE. 1A MODE REPLY 0 CFPFD /D/ 07BASE FOR LOWER SECTION,ADDITIONAL ADDITIONAL BASE FOR LOWER SECTION AN INDICATION OF WHETHER OR NOT AN ADDITIONAL BASE FOR THE LOWER SECTION IS INCLUDED. SELECT REPLY CODE 10AA49 CFPGD /D/ 07LID LID AN INDICATION OF WHETHER OR NOT A LID IS INCLUDED. SELECT REPLY CODE 10AA49 CFPHD 18TYPE,LID LID TYPE INDICATES THE TYPE OF LID PROVIDED. SELECT REPLY CODE 10AD99 CFPJJ 04DIAMETER,SECTION,LID UPPER LID UPPER SECTION DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LID UPPER SECTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFPKD /D/ 07ROD ROD AN INDICATION OF WHETHER OR NOT A ROD IS INCLUDED. SELECT REPLY CODE 10AA49 CFPLJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR AND LOCATION,CONNECTION,INLET INLET CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR AND LOCATION DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE INLET CONNECTION,AND THE THREAD LOCATION. 2D AND 1A MODE REPLY22AH063AJ91 CFPMJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR AND LOCATION,CONNECTION,OUTLET OUTLET CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR AND LOCATION DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE OUTLET CONNECTION,AND THE THREAD LOCATION. 2D AND 1A MODE REPLY22AH063AJ91 CFPND /D/ 07VALVE,OUTLET OUTLET VALVE AN INDICATION OF WHETHER OR NOT AN OUTLET VALVE(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CFPPD 18TYPE,DEVICE,MAXIMUM PRESSURE INDICATING MAXIMUM PRESSURE INDICATING DEVICE TYPE INDICATES THE TYPE OF DEVICE INCLUDED WITH THE ITEM FOR INDICATING WHEN THE MAXIMUM PRESSURE LIMIT OF THE ITEM HAS BEEN REACHED. SELECT REPLY CODE 10AG15 CFPQD /D/ 07DEFLATOR,SPECIAL SPECIAL DEFLATOR AN INDICATION OF WHETHER OR NOT A SPECIAL DEFLATOR IS INCLUDED. SELECT REPLY CODE 10AA49 CFPRD /D/ 07CLIP,HOLDING HOLDING CLIP AN INDICATION OF WHETHER OR NOT A HOLDING CLIP IS INCLUDED. SELECT REPLY CODE 10AA49 CFPSG /D/ 18TYPE AND SIZE FOR WHICH DESIGNED,COMPONENT,END CONNECTION END CONNECTION COMPONENT TYPE AND SIZE FOR WHICH DESIGNED INDICATES THE END CONNECTION COMPONENT TYPE AND SIZE FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 CFPTJ 04DIAMETER,RECESS,PACKING PACKING RECESS DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PACKING RECESS,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFPWJ 04DEPTH,RECESS,PACKING PACKING RECESS DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE PACKING RECESS,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CFPXD /D/ 07FEATURE,COUNTERSUNK,PACKING RECESS PACKING RECESS COUNTERSUNK FEATURE AN INDICATION OF WHETHER OR NOT A COUNTERSUNK FEATURE IS INCLUDED ON THE PACKING RECESS. SELECT REPLY CODE 10AA49 CFPYD /D/ 07WASHER,JOINT,SLIP SLIP JOINT WASHER AN INDICATION OF WHETHER OR NOT A SLIP JOINT WASHER IS INCLUDED. SELECT REPLY CODE 10AA49 CFPZD /D/ 07RING,FRICTION FRICTION RING AN INDICATION OF WHETHER OR NOT A FRICTION RING IS INCLUDED. SELECT REPLY CODE 10AA49 CFQBJ 04WIDTH,STEP,SHOULDER SHOULDER STEP WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CFQCJ 04DIAMETER,SEAT,SHOULDER SHOULDER SEAT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CFQDD /D/ 14SHAPE,SURFACE,OUTSIDE OUTSIDE SURFACE SHAPE THE PHYSICAL CONFIGURATION OF THE OUTSIDE SURFACE. SELECT REPLY CODE 10AD07 CFQGJ 04DIAMETER,OUTSIDE,MAJOR UNTHREADED MAJOR UNTHREADED OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CFQHA 12QUANTITY,PROTRUSION PROTRUSION QUANTITY NONE. 1A MODE REPLY 0 CFQJD 18TYPE FOR WHICH DESIGNED,END END TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF END FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK84 CFQKJ 10PRESSURE RATING,WORKING WORKING PRESSURE RATING THE WORKING PRESSURE AT WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY22AG671AC20 CFQLJ 04DIAMETER,HOLE,BOLT,SECOND SECOND BOLT HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CFQMB 10DEG BETWEEN OUTLETS DEG BETWEEN OUTLETS NONE. 1B MODE REPLY 0 CFQNJ 04LENGTH,SPLINE,STRAIGHT STRAIGHT SPLINE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A STRAIGHT SPLINE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CFQPJ 04DIAMETER,HOLE,THREADED SECTION PIN THREADED SECTION PIN HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED SECTION PIN HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFQQG 04SIZE,SECTION,SHAFT SHAFT SECTION SIZE THE DESIGNATION BY WHICH THE SIZE OF THE SHAFT SECTION(S) IS IDENTIFIED. FULL TEXT WRITE-IN 0 CFQRJ 04RADIUS,PORTION,CIRCULAR CIRCULAR PORTION RADIUS A MEASUREMENT OF THE DISTANCE FROM THE CENTER OF THE ITEM TO THE CURVE OF THE CIRCULAR SECTION. 2D AND 1B MODE REPLY21AA051AC20 CFQSJ 04DIAMETER,BEARING BEARING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BEARING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFQTA 12QUANTITY,SPLINE,STRAIGHT STRAIGHT SPLINE QUANTITY THE NUMBER OF STRAIGHT SPLINES ON THE ITEM. 1A MODE REPLY 0 CFQWJ 04SIZE AND LOCATION,CROSS SECTION CROSS SECTION SIZE AND LOCATION A MEASUREMENT OF THE DISTANCE FROM ONE SIDE TO THE OPPOSITE SIDE OF THE CROSS SECTION OF AN ITEM AND THE LOCATION. 3D AND 1B MODE REPLY31AA051AC203AJ91 CFQXG /D/ 04SIZE,FEATURE,MACHINED MACHINED FEATURE SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE MACHINED FEATURE OF THE ITEM. FULL TEXT WRITE-IN 0 CFQYA 12QUANTITY,HOLE,SECURING,THREADED THREADED SECURING HOLE QUANTITY THE NUMBER OF THREADED SECURING HOLES PROVIDED. 1A MODE REPLY 0 CFQZA 13THREAD SIZE,HOLE,SECURING SECURING HOLE THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A SECURING HOLE. 1A MODE REPLY 0 CFRBG 08LOCATION,HOLE,SECURING,THREADED THREADED SECURING HOLE LOCATION INDICATES THE LOCATION OF THE THREADED SECURING HOLE(S) ON THE ITEM. FULL TEXT WRITE-IN 0 CFRCA 12QUANTITY,HOLE,SECURING,UNTHREADED UNTHREADED SECURING HOLE QUANTITY THE NUMBER OF UNTHREADED SECURING HOLES PROVIDED. 1A MODE REPLY 0 CFRDG 08LOCATION,HOLE,SECURING,UNTHREADED UNTHREADED SECURING HOLE LOCATION INDICATES THE LOCATION OF THE UNTHREADED SECURING HOLE(S) ON THE ITEM. FULL TEXT WRITE-IN 0 CFRFJ 04DIAMETER,BUSHING,PANEL PANEL BUSHING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PANEL BUSHING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFRGJ /D/A13THREAD QUANTITY PER MEASUREMENT SCALE,BUSHING,PANEL PANEL BUSHING THREAD QUANTITY PER MEASUREMENT SCALE THE NUMBER OF PANEL BUSHING THREADS PER MEASUREMENT SCALE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. 1D AND 1A MODE REPLY13AJ40 CFRHJ /D/A18TYPE AND QUANTITY,FEATURE,ENGAGING ENGAGING FEATURE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF ENGAGING DEVICES PROVIDED. 1D AND 1A MODE REPLY13AK54 CFRJJ 04DIAMETER,PITCH,GEAR GEAR PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF THE GEAR. 2D AND 1B MODE REPLY21AA051AC20 CFRKG /D/ 04ANGLE IN DEG,HELIX HELIX ANGLE IN DEG THE ANGULAR AMOUNT THE HELIX IS INCLINED,EXPRESSED IN DEGREES. FULL TEXT WRITE-IN 0 CFRLB /D/ 04ANGLE IN DEG,PITCH,BEVEL GEAR BEVEL GEAR PITCH ANGLE IN DEG THE BEVEL GEAR PITCH ANGLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CFRMG /D/ 10DEFLECTION RATING,TORSIONAL TORSIONAL DEFLECTION RATING THE AMOUNT OF TWISTING OR DEGREE OF BENDING WHICH THE ITEM IS DESIGNED TO WITHSTAND. FULL TEXT WRITE-IN 0 CFRND /D/ 17SURFACE TREATMENT,CASING CASING SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE CASING SURFACE. SELECT REPLY CODE 10AD09 CFRPJ 04LENGTH BETWEEN FERRULES,CASING CASING LENGTH BETWEEN FERRULES A MEASUREMENT OF THE LONGEST DIMENSION OF THE CASING BETWEEN FERRULES,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CFRQJ 04DIAMETER,OUTSIDE,CASING CASING OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CASING,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFRRD 18TYPE,DEVICE,CASING PROTECTIVE CASING PROTECTIVE DEVICE TYPE INDICATES THE TYPE OF PROTECTIVE DEVICE INCLUDED WITH THE CASING. SELECT REPLY CODE 10AH83 CFRSA /D/ 12QUANTITY,HOLE,FLANGE MOUNTING FLANGE MOUNTING HOLE QUANTITY THE NUMBER OF FLANGE MOUNTING HOLES PROVIDED. 1A MODE REPLY 0 CFRTD /D/ 07END,SWIVEL SWIVEL END AN INDICATION OF WHETHER OR NOT A SWIVEL END(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CFRWJ 04DIAMETER,OVERALL,END END OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF THE END OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CFRXG 04SIZE,END,OVERALL OVERALL END SIZE DESIGNATES THE OVERALL SIZE OF THE END DIMENSIONS OF THE ITEM. FULL TEXT WRITE-IN 0 CFRYD /D/ 07FITTING,LUBRICATION LUBRICATION FITTING AN INDICATION OF WHETHER OR NOT A LUBRICATION FITTING(S) IS PROVIDED. PLEASEUSE MRC ABFF FOR NIINS WERE ANSWERED WITH "INCLUDED" IN PLACE OF THIS CANCELLED MRC. SELECT REPLY CODE 10AB22 CFRZJ 04LENGTH,OVERALL,CORE CORE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CORE. 2D AND 1B MODE REPLY21AA051AC20 CFSBD 05DIRECTION,ROTATION,CORE CORE ROTATION DIRECTION THE DIRECTION IN WHICH THE CORE IS DESIGNED TO ROTATE,WHEN VIEWED AXIALLY,FROM THE DRIVE END. SELECT REPLY CODE 10AA38 CFSCA /D/ 13THREAD SIZE,TIP,CORE CORE TIP THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE CORE TIP. 1A MODE REPLY 0 CFSDD /D/ 13THREAD SERIES DESIGNATOR,TIP,CORE CORE TIP THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE OF THE CORE TIP. SELECT REPLY CODE 10AH06 CFSFA 13THREAD CLASS,TIP,CORE CORE TIP THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL CORE TIP THREAD. 1A MODE REPLY 0 CFSGJ T13THREAD PITCH DIAMETER,NONSTANDARD NONSTANDARD THREAD PITCH DIAMETER THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A NONSTANDARD STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 CFSHD 13THREAD DIRECTION,TIP,CORE CORE TIP THREAD DIRECTION THE DIRECTION OF THE CORE TIP THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 CFSJJ 13THREAD LENGTH,TIP,CORE CORE TIP THREAD LENGTH A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS OF THE CORE TIP. 2D AND 1B MODE REPLY21AA051AC20 CFSKB /D/ 04ANGLE IN DEG,PITCH PITCH ANGLE IN DEG THE PITCH ANGLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CFSLD 07REMOVABILITY,CORE CORE REMOVABILITY AN INDICATION OF WHETHER OR NOT THE CORE(S) IS REMOVABLE. SELECT REPLY CODE 10AC29 CFSMJ /D/ 10CHARACTERISTICS,RATING,STRENGTH STRENGTH RATING CHARACTERISTICS AN INDICATION OF THOSE CHARACTERISTICS WHICH DETERMINE THE STRENGTH RATING OF THE ITEM. 3D AND 1B MODE REPLY31AA562AM453AA38 CFSNJ /D/ 04DISTANCE FROM BEND TO TIP END DISTANCE FROM BEND TO TIP END NONE. 2D AND 1B MODE REPLY21AA051AC20 CFSPB 10WATTAGE RATING IN KILOWATTS WATTAGE RATING IN KILOWATTS THE RATED POWER THAT AN ITEM CAN SAFELY CONSUME OR PROVIDE,MEASURED IN KILOWATTS. 1B MODE REPLY 0 CFSQD /D/ 07HEARTH,TILTING TILTING HEARTH AN INDICATION OF WHETHER OR NOT A TILTING HEARTH IS INCLUDED. SELECT REPLY CODE 10AA49 CFSRD /D/ 07BASKET,HOLDING,WORK WORK HOLDING BASKET AN INDICATION OF WHETHER OR NOT A WORK HOLDING BASKET IS INCLUDED. SELECT REPLY CODE 10AA49 CFSSG /D/ 08LOCATION AND QUANTITY,DOOR/OPENING DOOR/OPENING LOCATION AND QUANTITY INDICATES THE LOCATION AND NUMBER OF DOORS AND/OR OPENINGS. FULL TEXT WRITE-IN 0 CFSTD /D/ 07COUNTERWEIGHT COUNTERWEIGHT AN INDICATION OF WHETHER OR NOT A COUNTERWEIGHT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CFSWD /D/ 07EQUIPMENT FOR FLAME CURTAIN EQUIPMENT FOR FLAME CURTAIN AN INDICATION OF WHETHER OR NOT EQUIPMENT FOR A FLAME CURTAIN IS INCLUDED. PLEASE USE MRC ABFF OR MRC TMQY IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 CFSXD /D/ 09MATERIAL,HEARTH HEARTH MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HEARTH IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CFSYD 14SHAPE,HEARTH HEARTH SHAPE THE PHYSICAL CONFIGURATION OF THE HEARTH. SELECT REPLY CODE 10AD07 CFSZJ 04SIZE,HEARTH HEARTH SIZE DESIGNATES THE SIZE OF THE TOTAL SURFACE OF THE HEARTH. 1D AND 1B MODE REPLY12AG67 CFTBJ 04DEPTH,NOMINAL,HEARTH HEARTH NOMINAL DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF A HEARTH,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 CFTCD /D/ 07BOX,COAL COAL BOX AN INDICATION OF WHETHER OR NOT A COAL BOX IS INCLUDED. SELECT REPLY CODE 10AA49 CFTDD 18TYPE,HOOD HOOD TYPE INDICATES THE TYPE OF HOOD PROVIDED. SELECT REPLY CODE 10AK54 CFTFD /D/ 07BLOWER BLOWER AN INDICATION OF WHETHER OR NOT A BLOWER IS INCLUDED. SELECT REPLY CODE 10AA49 CFTGA /D/ 12QUANTITY,POCKET,TOTAL TOTAL POCKET QUANTITY THE TOTAL NUMBER OF POCKETS INCLUDED. 1A MODE REPLY 0 CFTHA 12QUANTITY,LOOP,TOTAL TOTAL LOOP QUANTITY THE TOTAL NUMBER OF LOOPS INCLUDED. 1A MODE REPLY 0 CFTJD /D/ 07INSULATION,COMPARTMENT COMPARTMENT INSULATION AN INDICATION OF WHETHER OR NOT COMPARTMENT INSULATION IS INCLUDED. SELECT REPLY CODE 10AA49 CFTKJ 10TEMP,MAINTAINED,MAXIMUM MAXIMUM MAINTAINED TEMP THE MAXIMUM TEMPERATURE AT WHICH THE ITEM CAN BE MAINTAINED. 1D AND 1B MODE REPLY11AB36 CFTLD 18TYPE,REPRESENTATION REPRESENTATION TYPE INDICATES THE REPRESENTATION TYPE PROVIDED BY THE ITEM. SELECT REPLY CODE 10AK54 CFTMD 19SIMULATED,EQUIPMENT,SPECIAL SPECIAL EQUIPMENT SIMULATED AN INDICATION OF THE SPECIAL EQUIPMENT THE ITEM SIMULATES. SELECT REPLY CODE 10AN51 CFTNA /D/ 12QUANTITY,SEGMENT,PANEL/SIMILAR PANEL/SIMILAR SEGMENT QUANTITY THE NUMBER OF PANELS AND/OR SIMILAR SEGMENTS PROVIDED. 1A MODE REPLY 0 CFTPG /D/ 11METHOD,PRESENTATION,COMPONENT/ITEM FUNCTIONING COMPONENT/ITEM FUNCTIONING PRESENTATION METHOD THE MEANS USED TO PRESENT THE FUNCTIONING OF THE COMPONENT(S) AND/OR ITEM(S). FULL TEXT WRITE-IN 0 CFTQG 19SIMULATED,SYSTEM SYSTEM SIMULATED AN INDICATION OF THE SYSTEM/S/ THE ITEM SIMULATES. FULL TEXT WRITE-IN 0 CFTRD 19GOVERNMENT,CONTROLLING,PROTOTYPE PROTOTYPE CONTROLLING GOVERNMENT THE NAME OF THE GOVERNMENT CONTROLLING THE PROTOTYPE. SELECT REPLY CODE 10AJ50 CFTSG 19AGENCY,CONTROLLING,PROTOTYPE PROTOTYPE CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE PROTOTYPE. FULL TEXT WRITE-IN 0 CFTTA 19NUMBER,MODEL,PROTOTYPE PROTOTYPE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE PROTOTYPE. 1A MODE REPLY 0 CFTWG 19NAME,MODEL,PROTOTYPE PROTOTYPE MODEL NAME AN INDICATION OF THE PROTOTYPE MODEL NAME. FULL TEXT WRITE-IN 0 CFTXG 19NAME,MANUFACTURER,PROTOTYPE PROTOTYPE MANUFACTURER NAME THE NAME OF THE MANUFACTURER OF THE PROTOTYPE. FULL TEXT WRITE-IN 0 CFTYA /D/ 12QUANTITY,MODEL MODEL QUANTITY THE NUMBER OF MODELS PROVIDED. 1A MODE REPLY 0 CFTZJ 04LENGTH,CONTAINER CONTAINER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CONTAINER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CFWBJ /D/ 04HEIGHT,CONTAINER CONTAINER HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE CONTAINER,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CFWCJ /D/ 04WIDTH,CONTAINER CONTAINER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CONTAINER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CFWDD /D/ 07FEATURE,COMPARTMENTAL,CONTAINER CONTAINER COMPARTMENTAL FEATURE AN INDICATION OF WHETHER OR NOT A CONTAINER COMPARTMENTAL FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CFWFG /D/ 19MODELED,AREA AREA MODELED THE AREA REPRESENTED BY THE MODEL. FULL TEXT WRITE-IN 0 CFWGD /D/ 09MATERIAL,FEATURE,TERRAIN TERRAIN FEATURE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TERRAIN FEATURE(S) IS FABRICATED. SELECT REPLY CODE 10AD09 CFWHA /D/ 10PROPORTION,SCALE,HORIZONTAL HORIZONTAL SCALE PROPORTION THE PROPORTIONAL HORIZONTAL SCALE OF THE ITEM. 1A MODE REPLY 0 CFWJA /D/ 10DIFFERENTIAL,SCALE,VERTICAL TO HORIZONTAL VERTICAL TO HORIZONTAL SCALE DIFFERENTIAL AN INDICATION OF THE EXTENT THAT THE VERTICAL SCALE DIFFERS FROM THE HORIZONTAL SCALE. 1A MODE REPLY 0 CFWKJ /D/ 04LENGTH,OVERALL,PANEL PANEL OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE PANEL. 2D AND 1B MODE REPLY21AA051AC20 CFWLJ /D/ 04WIDTH,OVERALL,PANEL PANEL OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PANEL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CFWMJ /D/ 04HEIGHT,OVERALL,PANEL PANEL OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF A PANEL. 2D AND 1B MODE REPLY21AA051AC20 CFWNJ /D/ 04LENGTH BETWEEN SHACKLE PIN CENTERLINE AND PELICAN HOOK CENTERLINE,MINIMUM MINIMUM LENGTH BETWEEN SHACKLE PIN CENTERLINE AND PELICAN HOOK CENTERLINE THE MINIMUM DISTANCE MEASURED FROM THE CENTERLINE OF THE SHACKLE PIN TO THE CENTERLINE OF THE PELICAN HOOK. 1D AND 1B MODE REPLY11AA05 CFWPJ /D/ 10TAKEUP TAKEUP THE DISTANCE THE ITEM CAN BE SHORTENED BY DRAWING TOGETHER. 2D AND 1B MODE REPLY21AA051AC20 CFWQD /D/ 07PLATE,LOCKING,TURNBUCKLE TURNBUCKLE LOCKING PLATE AN INDICATION OF WHETHER OR NOT A LOCKING PLATE FOR TURNBUCKLE IS INCLUDED. SELECT REPLY CODE 10AA49 CFWRD /D/ 07WRENCH,ADJUSTMENT ADJUSTMENT WRENCH AN INDICATION OF WHETHER OR NOT AN ADJUSTMENT WRENCH IS INCLUDED. SELECT REPLY CODE 10AA49 CFWSD /D/ 09MATERIAL,PLATE,COVER COVER PLATE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE COVER PLATE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CFWTG 10PRESSURE RATING,TEST TEST PRESSURE RATING THE AMOUNT OF PRESSURE THE ITEM WILL WITHSTAND. FULL TEXT WRITE-IN 0 CFWWD /D/ 07FEATURE,OPERATING,QUICK QUICK OPERATING FEATURE AN INDICATION OF WHETHER OR NOT A QUICK OPERATING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CFWXD 08LOCATION,OPERATING OPERATING LOCATION INDICATES THE LOCATION FROM WHICH THE ITEM CAN BE OPERATED. SELECT REPLY CODE 10AM56 CFWYG /D/ 04SIZE,OPENING OPENING SIZE DESIGNATES THE SIZE OF THE TOTAL SURFACE OF AN OPENING. FULL TEXT WRITE-IN 0 CFWZJ 04RADIUS,CORNER,OPENING OPENING CORNER RADIUS A MEASUREMENT OF A STRAIGHT LINE FROM THE MIDPOINT OF AN OPENING CORNER TO ITS CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFXBD 14SHAPE,OPENING,BOTTOM BOTTOM OPENING SHAPE THE PHYSICAL CONFIGURATION OF THE BOTTOM OPENING. SELECT REPLY CODE 10AD07 CFXCD 14SHAPE,OPENING,MOUTH MOUTH OPENING SHAPE THE PHYSICAL CONFIGURATION OF THE MOUTH OPENING. SELECT REPLY CODE 10AD07 CFXDJ 04DIAMETER,INSIDE,MOUTH OPENING MOUTH OPENING INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUTH OPENING,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CFXFJ 04WIDTH,INSIDE,MOUTH OPENING MOUTH OPENING INSIDE WIDTH AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUTH OPENING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CFXGJ 04HEIGHT,INSIDE,MOUTH OPENING MOUTH OPENING INSIDE HEIGHT AN INSIDE MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE MOUTH,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CFXHJ 04HEIGHT,COAMING COAMING HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE COAMING,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CFXJJ 04THICKNESS,COAMING COAMING THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE COAMING,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CFXKA 12QUANTITY,DOG DOG QUANTITY THE NUMBER OF DOGS FURNISHED WITH THE ITEM. 1A MODE REPLY 0 CFXLD 08LOCATION,DOG DOG LOCATION INDICATES THE LOCATION OF THE DOG(S). SELECT REPLY CODE 10AJ91 CFXMD 18TYPE,DOG DOG TYPE INDICATES THE TYPE OF DOG PROVIDED. SELECT REPLY CODE 10AK54 CFXND 08LOCATION,HASP HASP LOCATION INDICATES THE LOCATION OF THE HASP ON THE ITEM. SELECT REPLY CODE 10AJ91 CFXPD /D/ 07SCUTTLE,PASSING PASSING SCUTTLE AN INDICATION OF WHETHER OR NOT A PASSING SCUTTLE IS INCLUDED. SELECT REPLY CODE 10AA49 CFXQJ 04DISTANCE BETWEEN SILL AND PASSING SCUTTLE DISTANCE BETWEEN SILL AND PASSING SCUTTLE THE DISTANCE BETWEEN THE SILL AND THE PASSING SCUTTLE. 2D AND 1B MODE REPLY21AA051AC20 CFXRD 08LOCATION,SIDE,PASSING PASSING SIDE LOCATION INDICATES THE LOCATION OF THE PASSING SIDE. SELECT REPLY CODE 10AJ91 CFXSD /D/ 07LIGHT,FIXED FIXED LIGHT AN INDICATION OF WHETHER OR NOT A FIXED LIGHT IS INCLUDED. SELECT REPLY CODE 10AA49 CFXTJ 04DISTANCE BETWEEN SILL AND FIXED LIGHT DISTANCE BETWEEN SILL AND FIXED LIGHT THE DISTANCE FROM THE SILL TO THE FIXED LIGHT. 2D AND 1B MODE REPLY21AA051AC20 CFXWD /D/ 07BASE,MOUNTING,INTEGRAL INTEGRAL MOUNTING BASE AN INDICATION OF WHETHER OR NOT AN INTEGRAL MOUNTING BASE IS INCLUDED. SELECT REPLY CODE 10AA49 CFXXD 18TYPE,VENTILATOR VENTILATOR TYPE INDICATES THE TYPE OF VENTILATOR PROVIDED. SELECT REPLY CODE 10AK54 CFXYD /D/ 07PLATE,DECK DECK PLATE AN INDICATION OF WHETHER OR NOT A DECK PLATE IS INCLUDED. SELECT REPLY CODE 10AA49 CFXZG /D/ 04SIZE,PLATE,DECK DECK PLATE SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE DECK PLATE. FULL TEXT WRITE-IN 0 CFYBG 04SIZE,CONNECTION,SCREW SCREW CONNECTION SIZE DESIGNATES THE SIZE OF THE CONNECTION FURNISHED WITH THE SCREW. FULL TEXT WRITE-IN 0 CFYCD /D/ 07DEVICE,CLOSING,VENTILATION VENTILATION CLOSING DEVICE AN INDICATION OF WHETHER OR NOT A VENTILATION CLOSING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 CFYDD /D/ 07FEATURE,CLOSING,BELOW DECK BELOW DECK CLOSING FEATURE AN INDICATION OF WHETHER OR NOT A BELOW DECK CLOSING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CFYFD /D/ 07FEATURE,INSECTPROOF INSECTPROOF FEATURE AN INDICATION OF WHETHER OR NOT AN INSECTPROOF FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CFYGD /D/ 07FEATURE,BALANCE,SPRING SPRING BALANCE FEATURE AN INDICATION OF WHETHER OR NOT A SPRING BALANCE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CFYHD /D/ 07HASP HASP AN INDICATION OF WHETHER OR NOT A HASP IS INCLUDED. SELECT REPLY CODE 10AA49 CFYJD /D/ 07SCUTTLE SCUTTLE AN INDICATION OF WHETHER OR NOT A SCUTTLE IS INCLUDED. SELECT REPLY CODE 10AA49 CFYKG 19MARKINGS,CAP CAP MARKINGS MARKINGS INCLUDED ON THE CAP FOR PURPOSE OF READY IDENTIFICATION. FULL TEXT WRITE-IN 0 CFYLD /D/ 07CHAIN,RETAINING,CAP CAP RETAINING CHAIN AN INDICATION OF WHETHER OR NOT A CAP RETAINING CHAIN IS INCLUDED. SELECT REPLY CODE 10AA49 CFYMD /D/ 07THREADS,PIPE PIPE THREADS AN INDICATION OF WHETHER OR NOT PIPE THREADS ARE INCLUDED. SELECT REPLY CODE 10AA49 CFYND /D/ 09MATERIAL,PLY,INNER,TROUSER FRONT TROUSER FRONT INNER PLY MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TROUSER FRONT INNER PLY IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CFYPD /D/ 11METHOD,CLOSING,GARMENT FRONT GARMENT FRONT CLOSING METHOD THE MEANS BY WHICH THE GARMENT FRONT OPENING IS CLOSED. SELECT REPLY CODE 10AF69 CFYQD /D/ 08LOCATION,DEVICE,CLOSING,GARMENT FRONT GARMENT FRONT CLOSING DEVICE LOCATION INDICATES THE LOCATION OF THE CLOSING DEVICE ON THE GARMENT FRONT. SELECT REPLY CODE 10AJ91 CFYRD /D/ 07ACCESS TO INNER CLOTHING,OPENING,SIDE SIDE OPENING ACCESS TO INNER CLOTHING AN INDICATION OF WHETHER OR NOT A SIDE OPENING/S/ FOR ACCESS TO INNER CLOTHING IS INCLUDED. SELECT REPLY CODE 10AA49 CFYSD /D/ 09MATERIAL,COATING,OUTSIDE SHELL OUTSIDE SHELL COATING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE WITH WHICH THE OUTSIDE SHELL IS COATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CFYTD /D/ 08LOCATION,COATING,OUTSIDE SHELL OUTSIDE SHELL COATING LOCATION INDICATES THE LOCATION OF THE OUTSIDE SHELL TO WHICH THE COATING IS APPLIED. SELECT REPLY CODE 10AJ91 CFYWD /D/ 02DESIGN,PATTERN,OUTSIDE SHELL PERFORATION OUTSIDE SHELL PERFORATION PATTERN DESIGN THE PATTERN DESIGN OF THE OUTSIDE SHELL PERFORATION(S). SELECT REPLY CODE 10AK18 CFYXD /D/ 01COLOR,SHELL,OUTSIDE OUTSIDE SHELL COLOR THE HUE OR TINT OF THE OUTSIDE SHELL. SELECT REPLY CODE 10AD06 CFYYA /D/ 19IDENTIFICATION,SHADE,OUTSIDE SHELL OUTSIDE SHELL SHADE IDENTIFICATION A DESIGNATION ASSIGNED TO A PARTICULAR GRADATION OF THE OUTSIDE SHELL COLOR FOR PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 CFYZD /D/ 19SOURCE,SHADE,OUTSIDE SHELL OUTSIDE SHELL SHADE SOURCE THE NAME OF THE REFERENCE SOURCE OF THE OUTSIDE SHELL SHADE IDENTIFICATION DESIGNATOR. SELECT REPLY CODE 10AF94 CFZBD /D/ 09MATERIAL,BARRIER,VAPOR VAPOR BARRIER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE VAPOR BARRIER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CFZCD /D/ 09MATERIAL,COATING,VAPOR BARRIER VAPOR BARRIER COATING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE VAPOR BARRIER COATING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CFZDD /D/ 08LOCATION,COATING,VAPOR BARRIER VAPOR BARRIER COATING LOCATION INDICATES THE LOCATION OF THE VAPOR BARRIER TO WHICH THE COATING IS APPLIED. SELECT REPLY CODE 10AJ91 CFZFG /D/ 08LOCATION,LINING LINING LOCATION INDICATES THE LOCATION OF THE LINING ON THE ITEM. FULL TEXT WRITE-IN 0 CFZGA /D/ 19IDENTIFICATION,SHADE,LINING LINING SHADE IDENTIFICATION A DESIGNATION ASSIGNED TO A PARTICULAR GRADATION OF THE LINING COLOR FOR PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 CFZHD /D/ 19SOURCE,SHADE,LINING LINING SHADE SOURCE THE NAME OF THE REFERENCE SOURCE OF THE LINING SHADE IDENTIFICATION DESIGNATOR. SELECT REPLY CODE 10AF94 CFZJA /D/ 12QUANTITY,LAYER,INTERLINING INTERLINING LAYER QUANTITY THE NUMBER OF INTERLINING LAYERS PROVIDED. 1A MODE REPLY 0 CFZKD /D/ 07COVERS,GLOVES/SHOE,INTEGRAL INTEGRAL GLOVES/SHOE COVERS AN INDICATION OF WHETHER OR NOT INTEGRAL GLOVES AND/OR SHOE COVERS ARE INCLUDED. SELECT REPLY CODE 10AA49 CFZLJ /D/ 04WIDTH,HEM,SLACKS SLACKS HEM WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SLACKS HEM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CFZMD /D/ 11METHOD,ATTACHMENT,HOOD HOOD ATTACHMENT METHOD THE MEANS BY WHICH THE HOOD IS ATTACHED TO AN ITEM. SELECT REPLY CODE 10AM39 CFZND /D/ 11METHOD,SUPPORT,HOOD HOOD SUPPORT METHOD THE MEANS PROVIDED FOR SUPPORTING THE HOOD. SELECT REPLY CODE 10AH72 CFZPD /D/ 07HOOD,ATTACHED ATTACHED HOOD AN INDICATION OF WHETHER OR NOT AN ATTACHED HOOD IS INCLUDED. SELECT REPLY CODE 10AA49 CFZQD /D/ 18TYPE,FACEPIECE,ATTACHED HOOD ATTACHED HOOD FACEPIECE TYPE AN ATTACHED HOOD SHIELD FABRICATED FROM GLASS OR OTHER TRANSPARENT MATERIAL THAT PROTECTS THE FACE OF THE WEARER. SELECT REPLY CODE 10AG76 CFZRD /D/ 07COATING,CONDUCTOR,NONELECTRICAL,FACEPIECE FACEPIECE NONELECTRICAL CONDUCTOR COATING AN INDICATION OF WHETHER OR NOT A FACEPIECE NONELECTRICAL CONDUCTOR COATING IS INCLUDED. SELECT REPLY CODE 10AA49 CFZSD /D/ 09MATERIAL,COATING,FACEPIECE FACEPIECE COATING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE WITH WHICH THE FACEPIECE IS COATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CFZTD /D/ 11METHOD,SUPPORT,ATTACHED HOOD ATTACHED HOOD SUPPORT METHOD THE MEANS PROVIDED FOR SUPPORTING THE ATTACHED HOOD. SELECT REPLY CODE 10AH72 CFZWD /D/ 08LOCATION,FEED,AIR AIR FEED LOCATION INDICATES THE LOCATION OF THE AIR FEED IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 CFZXD 08LOCATION,EXHAUST,AIR AIR EXHAUST LOCATION INDICATES THE LOCATION OF THE AIR EXHAUST IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 CFZYD /D/ 11METHOD,EXHAUST,AIR AIR EXHAUST METHOD THE AIR EXHAUST MEANS PROVIDED. SELECT REPLY CODE 10AM42 CFZZD /D/ 07BELT,SAFETY SAFETY BELT AN INDICATION OF WHETHER OR NOT A SAFETY BELT IS INCLUDED. SELECT REPLY CODE 10AA49 CGBBD /D/ 07PALM,LEATHER LEATHER PALM AN INDICATION OF WHETHER OR NOT A LEATHER PALM/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CGBCD /D/ 07BOOTS,ATTACHED ATTACHED BOOTS AN INDICATION OF WHETHER OR NOT ATTACHED BOOTS ARE INCLUDED. SELECT REPLY CODE 10AA49 CGBDD /D/ 11METHOD,ADJUSTMENT,WAIST/SLEEVE/ANKLE WAIST/SLEEVE/ANKLE ADJUSTMENT METHOD THE MEANS OF ADJUSTING THE WAIST,SLEEVE/S/,AND ANKLES. SELECT REPLY CODE 10AL41 CGBFD /D/ 08LOCATION,CONNECTOR,ELECTRONIC,ATTENUATION TESTING ATTENUATION TESTING ELECTRONIC CONNECTOR LOCATION INDICATES THE LOCATION OF THE ATTENUATION TESTING ELECTRONIC CONNECTOR IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 CGBGJ /D/A19NUMBER,IDENTIFYING,CONNECTOR COVER CONNECTOR COVER IDENTIFYING NUMBER THE NUMBER ASSIGNED TO THE CONNECTOR COVER FOR THE PURPOSE OF READY IDENTIFICATION. 1D AND 1A MODE REPLY12AG99 CGBHD /D/ 07GENERATOR,SIGNALING SIGNALING GENERATOR AN INDICATION OF WHETHER OR NOT A SIGNALING GENERATOR IS FURNISHED. SELECT REPLY CODE 10AA55 CGBJJ /D/A19NUMBER,IDENTIFYING,SIGNALING GENERATOR SIGNALING GENERATOR IDENTIFYING NUMBER THE NUMBER ASSIGNED TO THE SIGNALING GENERATOR FOR THE PURPOSE OF READY IDENTIFICATION. 1D AND 1A MODE REPLY12AG99 CGBKD /D/ 07ANTENNA,TRANSMITTING TRANSMITTING ANTENNA AN INDICATION OF WHETHER OR NOT A TRANSMITTING ANTENNA IS FURNISHED. SELECT REPLY CODE 10AA55 CGBLJ /D/ 19NUMBER,IDENTIFYING,TRANSMITTING ANTENNA TRANSMITTING ANTENNA IDENTIFYING NUMBER THE NUMBER ASSIGNED TO THE TRANSMITTING ANTENNA FOR PURPOSE OF READY IDENTIFICATION. 1D AND 1B MODE REPLY12AG99 CGBMD /D/ 19SOURCE,PATTERN,BACKGROUND BACKGROUND PATTERN SOURCE THE NAME OF THE GOVERNMENT AGENCY,COMMERCIAL ORGANIZATION,OR MANUFACTURER CONTROLLING THE BACKGROUND PATTERN DESIGNATOR. SELECT REPLY CODE 10AF94 CGBNJ /D/ 04DISTANCE FROM OUTLET SIDE TO CORNER DISTANCE FROM OUTLET SIDE TO CORNER NONE. 2D AND 1B MODE REPLY21AA051AC20 CGBPJ /D/ 04THICKNESS AT TOP,FLANGE FLANGE THICKNESS AT TOP NONE. 2D AND 1B MODE REPLY21AA051AC20 CGBQJ /D/ 04THICKNESS AT WEB,FLANGE FLANGE THICKNESS AT WEB NONE. 2D AND 1B MODE REPLY21AA051AC20 CGBRJ /D/ 04WIDTH,RECESS,SASH SASH RECESS WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CGBSJ /D/ 04DEPTH,RECESS,SASH SASH RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CGBTJ /D/ 04DISTANCE FROM SASH RECESS CENTER TO CORNER DISTANCE FROM SASH RECESS CENTER TO CORNER NONE. 2D AND 1B MODE REPLY21AA051AC20 CGBWD /D/ 07PLUNGER PLUNGER AN INDICATION OF WHETHER OR NOT A PLUNGER IS INCLUDED. SELECT REPLY CODE 10AA49 CGBXJ 04LENGTH FROM SHOULDER TO BASE LENGTH FROM SHOULDER TO BASE A MEASUREMENT OF THE LONGEST DIMENSION FROM THE SHOULDER TO THE BASE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CGBYD /D/ 08LOCATION,USAGE,RUG RUG USAGE LOCATION INDICATES THE LOCATION AT WHICH THE RUG IS TO BE USED. SELECT REPLY CODE 10AJ91 CGBZJ 04DIAMETER,CENTER,TAPER TAPER CENTER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A TAPERED CIRCULAR ITEM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CGCBJ 10TIME,BURNING BURNING TIME THE LENGTH OF TIME THE ITEM WILL BURN. 2D AND 1B MODE REPLY22AG671AC20 CGCCB /D/ 10CONTENT IN PERCENT,BEESWAX BEESWAX CONTENT IN PERCENT THE BEESWAX CONTAINED IN THE ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 CGCDJ /D/A12QUANTITY PER UNIT OF MEASURE,CANDLE CANDLE QUANTITY PER UNIT OF MEASURE THE NUMBER OF CANDLES PER A SPECIFIC UNIT OF MEASURE. 1D AND 1A MODE REPLY12AG67 CGCFD /D/ 07ENDS,SELF-FITTING SELF-FITTING ENDS AN INDICATION OF WHETHER OR NOT SELF-FITTING ENDS ARE INCLUDED. SELECT REPLY CODE 10AA49 CGCGD /D/ 07SEAL,INNER INNER SEAL AN INDICATION OF WHETHER OR NOT AN INNER SEAL IS INCLUDED. SELECT REPLY CODE 10AA49 CGCHD /D/ 09MATERIAL,SEAL,INNER INNER SEAL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INNER SEAL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGCJD /D/ 02DESIGN,HANDRAIL HANDRAIL DESIGN THE DESIGN OF THE HANDRAIL. SELECT REPLY CODE 10AK54 CGCKD /D/ 08LOCATION,HANDRAIL HANDRAIL LOCATION INDICATES THE LOCATION OE THE HANDRAIL(S). SELECT REPLY CODE 10AJ91 CGCLD /D/ 09MATERIAL,TRIM,INTERIOR INTERIOR TRIM MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INTERIOR TRIM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGCMD /D/ 01COLOR,TRIM,INTERIOR INTERIOR TRIM COLOR THE HUE OR TINT OF THE INTERIOR TRIM. SELECT REPLY CODE 10AD06 CGCNJ /D/ 04LENGTH,FOLDED FOLDED LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ITEM WHEN IN A FOLDED POSITION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CGCPJ /D/ 04HEIGHT,FOLDED FOLDED HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE ITEM WHEN IN A FOLDED POSITION,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CGCQA 12QUANTITY,CASTER,LOCK SWIVEL LOCK SWIVEL CASTER QUANTITY THE NUMBER OF SWIVEL CASTERS CAPABLE OF BEING LOCKED. 1A MODE REPLY 0 CGCRA 12QUANTITY,WHEEL,BRAKE EQUIPPED BRAKE EQUIPPED WHEEL QUANTITY THE NUMBER OF WHEELS EQUIPPED WITH BRAKES. 1A MODE REPLY 0 CGCSD /D/ 09MATERIAL,TANK/PERCOLATOR TANK/PERCOLATOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TANK AND/OR PERCOLATOR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGCTD /D/ 17SURFACE TREATMENT,TANK/PERCOLATOR TANK/PERCOLATOR SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE TANK AND/OR PERCOLATOR SURFACE. SELECT REPLY CODE 10AD09 CGCWJ /D/ 10CAPACITY RATING,TANK/PERCOLATOR TANK/PERCOLATOR CAPACITY RATING THE RATED CAPACITY OF THE TANK AND/OR PERCOLATOR. 1D AND 1B MODE REPLY12AG67 CGCXD /D/ 03DESIGNATION,AWARD AWARD DESIGNATION AN INDICATION OF THE AWARD DESIGNATION. SELECT REPLY CODE 10AJ50 CGCYD 19CLASS CLASS AN INDICATION OF THE CLASS TO WHICH THE ITEM BELONGS. SELECT REPLY CODE 10AE92 CGCZB 10PERCENTAGE,CONTENT,NITROGEN NITROGEN CONTENT PERCENTAGE THE NITROGEN CONTENT OF THE ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 CGDBB 10PERCENTAGE,CONTENT,PHOSPHORIC OXIDE,AVAILABLE AVAILABLE PHOSPHORIC OXIDE CONTENT PERCENTAGE THE AVAILABLE PHOSPHORIC OXIDE CONTENT,EXPRESSED IN PERCENT. 1B MODE REPLY 0 CGDCB 10PERCENTAGE,CONTENT,POTASH,AVAILABLE AVAILABLE POTASH CONTENT PERCENTAGE THE AVAILABLE POTASH CONTENT,EXPRESSED IN PERCENT. 1B MODE REPLY 0 CGDDB 10PERCENTAGE,CONTENT,MOISTURE,MAXIMUM MAXIMUM MOISTURE CONTENT PERCENTAGE THE MAXIMUM MOISTURE CONTENT OF THE ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 CGDFB 10PERCENTAGE BY WEIGHT,CONTENT,ASH,MAXIMUM MAXIMUM ASH CONTENT PERCENTAGE BY WEIGHT THE MAXIMUM ASH CONTENT OF THE ITEM,EXPRESSED IN PERCENT BY WEIGHT. 1B MODE REPLY 0 CGDGB /D/ 10PERCENTAGE,RETENTION,WATER,MINIMUM MINIMUM WATER RETENTION PERCENTAGE THE MINIMUM PERCENTAGE OF WATER THE ITEM IS CAPABLE OF HOLDING. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 1B MODE REPLY 0 CGDHG /D/ 19INGREDIENT AND WEIGHT PER 100000 CAPSULES INGREDIENT AND WEIGHT PER 100000 CAPSULES THE NAME AND WEIGHT OF THE INDIVIDUAL INGREDIENTS PER 100000 CAPSULES. FULL TEXT WRITE-IN 0 CGDJD 19VARIETY VARIETY A NAME WHICH REPRESENTS A CLASSIFICATION OF A SUBSPECIES. SELECT REPLY CODE 10AL42 CGDKB 10PERCENTAGE,CONTENT,VARIETY VARIETY CONTENT PERCENTAGE THE VARIETY CONTENT,EXPRESSED IN PERCENT. 1B MODE REPLY 0 CGDLB 10PERCENTAGE,PURITY,MINIMUM MINIMUM PURITY PERCENTAGE THE MINIMUM PURITY LEVEL OF THE ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 CGDMB 10PERCENTAGE,GERMINATION,MINIMUM MINIMUM GERMINATION PERCENTAGE THE MINIMUM PERCENTAGE OF GERMINATION. 1B MODE REPLY 0 CGDNJ 04RADIUS,OPERATING,MINIMUM MINIMUM OPERATING RADIUS THE RADIUS OF THE SMALLEST OPERATING CIRCLE FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AA05 CGDPJ /D/ 10STRENGTH,TORQUE,MAXIMUM MAXIMUM TORQUE STRENGTH THE MAXIMUM TORQUE LOAD FOR WHICH THE ITEM IS RATED. 2D AND 1B MODE REPLY21AA561AB39 CGDQJ 10DEFLECTION IN DEG,ANGULAR,MAXIMUM SHAFT MAXIMUM SHAFT ANGULAR DEFLECTION IN DEG THE MAXIMUM AMOUNT OF SHAFT ANGULAR DEFLECTION,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AB39 CGDRD /D/ 07CASING,METAL METAL CASING AN INDICATION OF WHETHER OR NOT A METAL CASING(S) IS PROVIDED. SELECT REPLY CODE 10AB22 CGDSD /D/ 09MATERIAL,COVER,CASE CASE COVER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CASE COVER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGDTD 01COLOR,TOPSIDE TOPSIDE COLOR THE HUE OR TINT OF THE TOPSIDE. SELECT REPLY CODE 10AD06 CGDWD 01COLOR,UNDERSIDE UNDERSIDE COLOR THE HUE OR TINT OF THE UNDERSIDE. SELECT REPLY CODE 10AD06 CGDXA 12QUANTITY SUPPORTED ALONGSIDE,PERSONNEL PERSONNEL QUANTITY SUPPORTED ALONGSIDE THE NUMBER OF PERSONS THAT CAN BE SUPPORTED ALONGSIDE. 1A MODE REPLY 0 CGDYD 11METHOD,INFLATION INFLATION METHOD THE MEANS USED TO INFLATE THE ITEM. SELECT REPLY CODE 10AH53 CGDZD /D/ 07CYLINDER,GAS,CARBON DIOXIDE CARBON DIOXIDE GAS CYLINDER AN INDICATION OF WHETHER OR NOT A CARBON DIOXIDE GAS CYLINDER(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CGFBJ 04WIDTH,BEAM BEAM WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BEAM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CGFCD /D/ 07COVER,RESISTANT,FIRE FIRE RESISTANT COVER AN INDICATION OF WHETHER OR NOT A FIRE RESISTANT COVER/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CGFDD /D/ 07SAIL SAIL AN INDICATION OF WHETHER OR NOT A SAIL(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CGFFA /D/ 12QUANTITY,PACK,PARACHUTE PARACHUTE PACK QUANTITY THE NUMBER OF PARACHUTE PACKS INCLUDED WITH THE ITEM. 1A MODE REPLY 0 CGFGA /D/ 12QUANTITY PER PACK,PARACHUTE PARACHUTE QUANTITY PER PACK THE NUMBER OF PARACHUTES CONTAINED IN EACH PACK. 1A MODE REPLY 0 CGFHJ /D/ 04DIAMETER,CANOPY,PARACHUTE PARACHUTE CANOPY DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PARACHUTE CANOPY HAVING A SHAPE OTHER THAN RECTANGULAR OR SQUARE,AND TERMINATES AT THE EXTREME ENDS OF THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CGFJJ /D/ 10RANGE,CRUISING,MAXIMUM MAXIMUM CRUISING RANGE THE MAXIMUM CRUISING RANGE OF THE ITEM. 1D AND 1B MODE REPLY13AJ40 CGFKD /D/ 07CONTROL,REMOTE,RADIO RADIO REMOTE CONTROL AN INDICATION OF WHETHER OR NOT RADIO REMOTE CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 CGFLD 07APPROVAL,US COAST GUARD US COAST GUARD APPROVAL AN INDICATION OF WHETHER OR NOT THE ITEM HAS BEEN APPROVED BY THE UNITED STATES COAST GUARD. SELECT REPLY CODE 10AM27 CGFMD /D/ 07CYLINDER,GAS GAS CYLINDER AN INDICATION OF WHETHER OR NOT A GAS CYLINDER(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CGFNG /D/ 11METHOD,FASTENING FASTENING METHOD THE MEANS BY WHICH THE ITEM IS FASTENED. FULL TEXT WRITE-IN 0 CGFPD 11METHOD,BUOYANCY BUOYANCY METHOD THE MEANS USED TO RENDER THE ITEM BUOYANT. SELECT REPLY CODE 10AH53 CGFQJ 04DEPTH,DIVING,RECOMMENDED,MAXIMUM MAXIMUM RECOMMENDED DIVING DEPTH AN INDICATION OF THE MAXIMUM DEPTH RECOMMENDED FOR SAFE DIVING. 1D AND 1B MODE REPLY11AA05 CGFRA /D/ 12QUANTITY PER BANK,FLASK FLASK QUANTITY PER BANK THE NUMBER OF FLASKS CONTAINED IN EACH BANK. 1A MODE REPLY 0 CGFSA /D/ 12QUANTITY,POCKET,TOOL TOOL POCKET QUANTITY THE NUMBER OF TOOL POCKETS INCLUDED IN THE ITEM. 1A MODE REPLY 0 CGFTD /D/ 07PROVISION,LACING,LEG LEG LACING PROVISION AN INDICATION OF WHETHER OR NOT A LEG LACING PROVISION/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CGFXD /D/ 07CUFFS,ATTACHED ATTACHED CUFFS AN INDICATION OF WHETHER OR NOT ATTACHED CUFFS ARE INCLUDED. SELECT REPLY CODE 10AA49 CGFYD /D/ 09MATERIAL,LINING,INNER INNER LINING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INNER LINING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGFZD /D/ 09MATERIAL,FABRIC,OUTER OUTER FABRIC MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE OUTER FABRIC IS MADE,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGGBD /D/ 14SHAPE,PREFORMED PREFORMED SHAPE THE PREFORMED SHAPE OF THE ITEM. SELECT REPLY CODE 10AD07 CGGCD /D/ 09MATERIAL,WEIGHT WEIGHT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WEIGHT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGGDD 19FINISH,TANNING,STRAP STRAP TANNING FINISH AN INDICATION OF THE TANNING FINISH ON THE STRAP. SELECT REPLY CODE 10AG36 CGGFD 19FINISH,BUCKLE BUCKLE FINISH AN INDICATION OF THE FINISH OF THE BUCKLE. SELECT REPLY CODE 10AG33 CGGGJ 03DESIGNATION,SIZE,WEIGHT WEIGHT SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE OF THE WEIGHT(S). 1D AND 1B MODE REPLY12AG67 CGGHG 11METHOD,SECURING,WEIGHT WEIGHT SECURING METHOD THE MEANS USED TO SECURE THE WEIGHT(S). FULL TEXT WRITE-IN 0 CGGJD /D/ 13THREAD SERIES DESIGNATOR,MOUNTING MOUNTING THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO THE MOUNTING DIAMETER. SELECT REPLY CODE 10AH06 CGGKJ A13THREAD QUANTITY,MOUNTING MOUNTING THREAD QUANTITY THE NUMBER OF MOUNTING THREADS ON THE ITEM MEASURED ON A LINE PARALLEL TO THE THREAD AXIS,INCLUDING INCOMPLETE THREADS. 1D AND 1A MODE REPLY11AB39 CGGLD /D/ 07STRAP,SHOULDER SHOULDER STRAP AN INDICATION OF WHETHER OR NOT A SHOULDER STRAP(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CGGMG /D/ 19CHARACTERISTIC,LAYER,INNER INNER LAYER CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC(S) OF THE INNER LAYER OF THE ITEM. FULL TEXT WRITE-IN 0 CGGNA /D/ 19IDENTIFICATION,PATTERN,BACKGROUND BACKGROUND PATTERN IDENTIFICATION A DESIGNATION ASSIGNED TO THE BACKGROUND PATTERN FOR THE PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 CGGPD /D/ 19SOURCE,PATTERN,STRIPES/CHECKS STRIPES/CHECKS PATTERN SOURCE THE NAME OF THE GOVERNMENT AGENCY,COMMERCIAL ORGANIZATION,OR MANUFACTURER CONTROLLING THE STRIPES AND/OR CHECKS PATTERN DESIGNATOR. SELECT REPLY CODE 10AF94 CGGQA /D/ 19IDENTIFICATION,PATTERN,STRIPES/CHECKS STRIPES/CHECKS PATTERN IDENTIFICATION A DESIGNATION ASSIGNED TO THE STRIPES AND/OR CHECKS PATTERN FOR THE PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 CGGRD /D/ 07FEATURE,NONSTATIC NONSTATIC FEATURE AN INDICATION OF WHETHER OR NOT A NONSTATIC FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CGGSD /D/ 07COVERING,FLY,UPPER GARMENT UPPER GARMENT FLY COVERING AN INDICATION OF WHETHER OR NOT AN UPPER GARMENT FLY COVERING IS INCLUDED. SELECT REPLY CODE 10AA49 CGGTD /D/ 07FLAP,CLOSURE,PROTECTIVE,BUTTON BUTTON PROTECTIVE CLOSURE FLAP AN INDICATION OF WHETHER OR NOT A BUTTON PROTECTIVE CLOSURE FLAP IS INCLUDED. SELECT REPLY CODE 10AA49 CGGWD /D/ 18TYPE,CUFF,LEG LEG CUFF TYPE INDICATES THE TYPE OF LEG CUFF(S) PROVIDED. SELECT REPLY CODE 10AF69 CGGXD /D/ 11METHOD,ADJUSTMENT,LEG CUFF LEG CUFF ADJUSTMENT METHOD THE MEANS PROVIDED TO ADJUST THE LEG CUFF/S/. SELECT REPLY CODE 10AL41 CGGYD /D/ 07PIECE,FLY,PROTECTIVE,FRONT OPENING FRONT OPENING PROTECTIVE FLY PIECE AN INDICATION OF WHETHER OR NOT A FRONT OPENING PROTECTIVE FLY PIECE IS INCLUDED. SELECT REPLY CODE 10AA49 CGGZD /D/ 11METHOD,CLOSING,INSIDE FLAP INSIDE FLAP CLOSING METHOD THE MEANS BY WHICH THE INSIDE FLAP IS CLOSED. SELECT REPLY CODE 10AF69 CGHBD /D/ 08LOCATION,HOLDER,IDENTIFICATION IDENTIFICATION HOLDER LOCATION INDICATES THE LOCATION OF THE IDENTIFICATION HOLDER IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 CGHCD /D/ 07LINING,GARMENT,UPPER UPPER GARMENT LINING AN INDICATION OF WHETHER OR NOT AN UPPER GARMENT LINING IS FURNISHED. SELECT REPLY CODE 10AA55 CGHDD /D/ 19FIBER,LINING LINING FIBER THE NATURAL AND/OR MAN-MADE FIBERS COMPRISING THE LINING. SELECT REPLY CODE 10AD09 CGHFB /D/ 10PERCENT,FIBER,LINING LINING FIBER PERCENT THE PERCENTAGE OF NATURAL AND/OR MAN-MADE FIBERS COMPRISING THE LINING. 1B MODE REPLY 0 CGHGD /D/ 07VENT,SWORD SWORD VENT AN INDICATION OF WHETHER OR NOT A SWORD VENT IS INCLUDED. SELECT REPLY CODE 10AA49 CGHHD /D/ 08LOCATION,VENT,SWORD SWORD VENT LOCATION INDICATES THE LOCATION OF THE SWORD VENT IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 CGHJD /D/ 11METHOD,CLOSING,SWORD VENT SWORD VENT CLOSING METHOD THE MEANS OF CLOSING THE SWORD VENT OPENING. SELECT REPLY CODE 10AF69 CGHKD /D/ 07BRAID,SLEEVE,SEWN-ON SEWN-ON SLEEVE BRAID AN INDICATION OF WHETHER OR NOT SEWN-ON SLEEVE BRAID IS INCLUDED. SELECT REPLY CODE 10AA49 CGHLD /D/ 07DEVICE,COLLAR,SEWN-ON SEWN-ON COLLAR DEVICE AN INDICATION OF WHETHER OR NOT A SEWN-ON COLLAR DEVICE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CGHMA /D/ 12QUANTITY,POCKET,TROUSERS TROUSERS POCKET QUANTITY THE NUMBER OF TROUSERS POCKETS INCLUDED. 1A MODE REPLY 0 CGHND /D/ 18TYPE,POCKET,TROUSERS TROUSERS POCKET TYPE INDICATES THE TYPE OF TROUSERS POCKET BY THE STYLE OR DESIGN. SELECT REPLY CODE 10AF87 CGHPD /D/ 08LOCATION,POCKET,TROUSERS TROUSERS POCKET LOCATION INDICATES THE LOCATION OF THE POCKET(S) IN OR ON THE TROUSERS. SELECT REPLY CODE 10AJ91 CGHQD /D/ 07FLAP,POCKET,TROUSERS TROUSERS POCKET FLAP AN INDICATION OF WHETHER OR NOT A TROUSERS POCKET FLAP(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CGHRD /D/ 11METHOD,CLOSING,TROUSERS FLY TROUSERS FLY CLOSING METHOD THE MEANS BY WHICH THE TROUSERS FLY OPENING IS CLOSED. SELECT REPLY CODE 10AF69 CGHSD /D/ 07PIECE,FLY,PROTECTIVE,TROUSERS FRONT OPENING TROUSERS FRONT OPENING PROTECTIVE FLY PIECE AN INDICATION OF WHETHER OR NOT A TROUSERS FRONT OPENING PROTECTIVE FLY PIECE IS INCLUDED. SELECT REPLY CODE 10AA49 CGHTA /D/ 12QUANTITY,POCKET,SKIRT SKIRT POCKET QUANTITY THE NUMBER OF POCKETS INCLUDED IN THE SKIRT. 1A MODE REPLY 0 CGHWD /D/ 18TYPE,POCKET,SKIRT SKIRT POCKET TYPE INDICATES THE TYPE OF SKIRT POCKET BY THE STYLE OR DESIGN. SELECT REPLY CODE 10AF87 CGHXD /D/ 08LOCATION,POCKET,SKIRT SKIRT POCKET LOCATION INDICATES THE LOCATION OF THE POCKET IN THE SKIRT. SELECT REPLY CODE 10AJ91 CGHYD /D/ 07FLAP,POCKET,SKIRT SKIRT POCKET FLAP AN INDICATION OF WHETHER OR NOT A SKIRT POCKET FLAP(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CGHZD /D/ 11METHOD,CLOSING,SKIRT POCKET SKIRT POCKET CLOSING METHOD THE MEANS BY WHICH THE SKIRT POCKET OPENING IS CLOSED. SELECT REPLY CODE 10AF69 CGJBD 13THREAD LOCATION,END,CONNECTING CONNECTING END THREAD LOCATION INDICATES THE LOCATION OF THE THREAD ON THE CONNECTING END OF THE ITEM. SELECT REPLY CODE 10AJ91 CGJCJ /D/ 04LENGTH,WAISTBAND TOP TO SKIRT BOTTOM WAISTBAND TOP TO SKIRT BOTTOM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION FROM THE TOP OF THE WAISTBAND TO THE SKIRT BOTTOM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CGJDA /D/ 12QUANTITY,OPENING,SLACKS PLACKET SLACKS PLACKET OPENING QUANTITY THE NUMBER OF PLACKET OPENINGS INCLUDED IN THE SLACKS. 1A MODE REPLY 0 CGJFA /D/ 12QUANTITY,POCKET,SLACKS SLACKS POCKET QUANTITY THE NUMBER OF POCKETS INCLUDED IN THE SLACKS. 1A MODE REPLY 0 CGJGD /D/ 18TYPE,POCKET,SLACKS SLACKS POCKET TYPE INDICATES THE TYPE OF SLACKS POCKET BY THE STYLE OR DESIGN. SELECT REPLY CODE 10AF87 CGJHD /D/ 08LOCATION,POCKET,SLACKS SLACKS POCKET LOCATION INDICATES THE LOCATION OF THE POCKET(S) IN OR ON THE SLACKS. SELECT REPLY CODE 10AJ91 CGJJD /D/ 07FLAP,POCKET,SLACKS SLACKS POCKET FLAP AN INDICATION OF WHETHER OR NOT A SLACKS POCKET FLAP(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CGJKD /D/ 11METHOD,CLOSING,SLACKS POCKET SLACKS POCKET CLOSING METHOD THE MEANS BY WHICH THE SLACKS POCKET OPENING IS CLOSED. SELECT REPLY CODE 10AF69 CGJLG /D/ 18TYPE FOR WHICH DESIGNED,ARMOR,BODY BODY ARMOR TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF BODY ARMOR FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 CGJMD /D/ 09MATERIAL,BACK/CHEST PLATE CUSHION/SPALL COVER BACK/CHEST PLATE CUSHION/SPALL COVER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BACK,CHEST PLATE CUSHION,AND SPALL COVER ARE FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGJNA 12QUANTITY,HOLE,FLANGE MOUNTING FLANGE MOUNTING HOLE QUANTITY THE NUMBER OF MOUNTING HOLES IN THE FLANGE. 1A MODE REPLY 0 CGJPD /D/ 07KEY KEY AN INDICATION OF WHETHER OR NOT A KEY IS INCLUDED. SELECT REPLY CODE 10AA49 CGJQD 08LOCATION,HINGE,RETANGULAR HATCH RECTANGULAR HATCH HINGE LOCATION INDICATES THE LOCATION OF THE HINGE ON A RECTANGULAR HATCH. SELECT REPLY CODE 10AJ91 CGJRD 11METHOD,COUNTERBALANCE COUNTERBALANCE METHOD THE MEANS USED TO COUNTERBALANCE THE ITEM. SELECT REPLY CODE 10AM39 CGJSA 12QUANTITY,BERTH BERTH QUANTITY THE NUMBER OF BERTHS FURNISHED WITH THE ITEM. 1A MODE REPLY 0 CGJTD /D/ 07MATTRESS MATTRESS AN INDICATION OF WHETHER OR NOT A MATTRESS(ES) IS INCLUDED. SELECT REPLY CODE 10AA49 CGJWJ 04LENGTH ACCOMMODATED,OVERALL,MATTRESS MATTRESS OVERALL LENGTH ACCOMMODATED THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE MATTRESS THE ITEM WILL ACCOMMODATE. 2D AND 1B MODE REPLY21AA051AC20 CGJXJ 04WIDTH ACCOMMODATED,OVERALL,MATTRESS MATTRESS OVERALL WIDTH ACCOMMODATED AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MATTRESS THE ITEM WILL ACCOMMODATE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CGJYJ 04THICKNESS ACCOMMODATED,OVERALL,MATTRESS MATTRESS OVERALL THICKNESS ACCOMMODATED AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF THE MATTRESS THE ITEM WILL ACCOMMODATE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CGJZD /D/ 07RAIL,GUARD,REMOVABLE REMOVABLE GUARD RAIL AN INDICATION OF WHETHER OR NOT A REMOVABLE GUARD RAIL(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CGKBD /D/ 07RETAINER,BEDDING BEDDING RETAINER AN INDICATION OF WHETHER OR NOT A BEDDING RETAINER IS INCLUDED. SELECT REPLY CODE 10AA49 CGKCD /D/ 09MATERIAL,COVERING,TRANSOM TRANSOM COVERING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TRANSOM COVERING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGKDD /D/ 09MATERIAL,PADDING,TRANSOM TRANSOM PADDING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TRANSOM PADDING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGKFA 12QUANTITY,DRAWER,TRANSOM TRANSOM DRAWER QUANTITY THE NUMBER OF DRAWERS PROVIDED IN THE TRANSOM. 1A MODE REPLY 0 CGKGD 18TYPE,BERTH BERTH TYPE INDICATES THE TYPE OF BERTH PROVIDED. SELECT REPLY CODE 10AC55 CGKHD 18TYPE,COAT,FINISH FINISH COAT TYPE INDICATES THE TYPE OF FINISH COAT PROVIDED. SELECT REPLY CODE 10AL72 CGKJD /D/ 07BOTTOM BOTTOM AN INDICATION OF WHETHER OR NOT A BOTTOM IS INCLUDED. SELECT REPLY CODE 10AA49 CGKKD 10CAPACITY,BERTH BERTH CAPACITY THE NUMBER OF PERSONS THE BERTH WILL ACCOMMODATE. SELECT REPLY CODE 10AL77 CGKLD /D/ 09MATERIAL,CELL CELL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CELL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGKMJ T10RANGE,CAPACITY,AIR FLOW AIR FLOW CAPACITY RANGE A MEASUREMENT OF THE MINIMUM AND MAXIMUM VOLUME OF AIR MOVED THROUGH THE ITEM. 1D AND 1F MODE REPLY12AG67 CGKNA 12QUANTITY,CELL,SCREEN SCREEN CELL QUANTITY THE NUMBER OF CELLS PROVIDED IN THE SCREEN. 1A MODE REPLY 0 CGKPJ 04DIAMETER,LARGEST,BODY BODY LARGEST DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CGKQJ 04HEIGHT FROM COUNTERWEIGHT BOTTOM TO LANTERN FOCAL PLANE HEIGHT FROM COUNTERWEIGHT BOTTOM TO LANTERN FOCAL PLANE A MEASUREMENT FROM THE BOTTOM OF THE COUNTERWEIGHT TO THE FOCAL PLANE OF THE LANTERN. 2D AND 1B MODE REPLY21AA051AC20 CGKRD /D/ 07REFLECTOR,RADAR RADAR REFLECTOR AN INDICATION OF WHETHER OR NOT A RADAR REFLECTOR IS INCLUDED. SELECT REPLY CODE 10AA49 CGKSD /D/ 07DEVICE,SOUND SOUND DEVICE AN INDICATION OF WHETHER OR NOT A SOUND DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 CGKTD 11METHOD,LIGHTING LIGHTING METHOD THE MEANS USED TO LIGHT THE ITEM. SELECT REPLY CODE 10AB75 CGKXD /D/ 19CLASS,COAST GUARD COAST GUARD CLASS DESIGNATES THE COAST GUARD CLASSIFICATION. SELECT REPLY CODE 10AJ91 CGKYD /D/ 18TYPE,COAST GUARD COAST GUARD TYPE INDICATES THE COAST GUARD TYPE. SELECT REPLY CODE 10AK54 CGKZG 19CLASS FOR WHICH DESIGNED,VESSEL VESSEL CLASS FOR WHICH DESIGNED THE CLASS OF VESSEL FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 CGLBD 03DESIGNATION,USAGE,SPECIFICATION SPECIFICATION USAGE DESIGNATION THE DESIGNED USE OF THE ITEM AS DIRECTED BY A SPECIFICATION. SELECT REPLY CODE 10AE74 CGLCD /D/ 07FEATURE,AIR-ENTRAINING AIR-ENTRAINING FEATURE AN INDICATION OF WHETHER OR NOT AN AIR-ENTRAINING FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 CGLDD /D/ 07FEATURE,CUTBACK CUTBACK FEATURE AN INDICATION OF WHETHER OR NOT A CUTBACK FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CGLFD /D/ 07EMULSION EMULSION AN INDICATION OF WHETHER OR NOT EMULSION IS INCLUDED. SELECT REPLY CODE 10AA49 CGLGD /D/ 07FEATURE,PENETRATION PENETRATION FEATURE AN INDICATION OF WHETHER OR NOT A PENETRATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CGLHG /D/ 10RANGE,PENETRATION PENETRATION RANGE AN INDICATION OF THE PENETRATION RANGE. FULL TEXT WRITE-IN 0 CGLJJ T10RANGE,SOFTENING,PENETRATION PENETRATION SOFTENING RANGE AN INDICATION OF THE PENETRATION SOFTENING MINIMUM AND MAXIMUM LIMITS. 1D AND 1F MODE REPLY13AJ40 CGLLD /D/ 07FILLER,MINERAL MINERAL FILLER AN INDICATION OF WHETHER OR NOT A MINERAL FILLER IS INCLUDED. SELECT REPLY CODE 10AA49 CGLMD 19CONSISTENCY,FILLER,MINERAL MINERAL FILLER CONSISTENCY AN INDICATION OF THE CONSISTENCY OF THE MINERAL FILLER. SELECT REPLY CODE 10AL32 CGLNA 12QUANTITY,CONNECTION,FLUID FLUID CONNECTION QUANTITY THE NUMBER OF FLUID CONNECTIONS PROVIDED. 1A MODE REPLY 0 CGLPG /D/ 18TYPE AND SIZE FOR WHICH DESIGNED,CONVEYANCE,FLUID FLUID CONVEYANCE TYPE AND SIZE FOR WHICH DESIGNED INDICATES THE FLUID CONVEYANCE TYPE AND SIZE FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 CGLQD /D/ 07SERRATIONS,FLATS,BOLT HOLE BOLT HOLE FLATS SERRATIONS AN INDICATION OF WHETHER OR NOT SERRATIONS ARE PROVIDED ON BOLT HOLE FLATS. SELECT REPLY CODE 10AB22 CGLRD /D/ 07PASSAGE,FLUID,BOLT HOLE BOLT HOLE FLUID PASSAGE AN INDICATION OF WHETHER OR NOT A BOLT HOLE FLUID PASSAGE IS PROVIDED. SELECT REPLY CODE 10AB22 CGLSD /D/ 07HOLE,LOCKWIRE LOCKWIRE HOLE AN INDICATION OF WHETHER OR NOT A LOCKWIRE HOLE IS INCLUDED. SELECT REPLY CODE 10AA49 CGLTB /D/ 10DEG BETWEEN OUTLETS,SECOND SECOND DEG BETWEEN OUTLETS NONE. 1B MODE REPLY 0 CGLWJ /D/ 04HEIGHT,SLOT,MOUNTING MOUNTING SLOT HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CGLXJ 04DISTANCE FROM FLANGED END TO TUBING CLEARANCE HOLE DISTANCE FROM FLANGED END TO TUBING CLEARANCE HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 CGLYJ 04DIAMETER,FACE,FLANGE FLANGE FACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CGLZJ /D/ 04HEIGHT,FLANGE,SMALLEST SMALLEST FLANGE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CGMBD 07APPROVAL,LIQUID,INGESTED INGESTED LIQUID APPROVAL AN INDICATION OF WHETHER OR NOT INGESTED LIQUID USE IS APPROVED. SELECT REPLY CODE 10AM27 CGMCJ 04DIAMETER,CIRCLE,BOLT,END END BOLT CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN END BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CGMDD 13SCREW THREAD SERIES DESIGNATOR,EXTERNAL EXTERNAL SCREW THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF EXTERNAL SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CGMFD 13THREAD DIRECTION,EXTERNAL EXTERNAL THREAD DIRECTION THE DIRECTION OF THE EXTERNAL THREAD WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AA38 CGMGJ 04SIZE,PIPE,NOMINAL,DRAIN HOLE CONNECTION DRAIN HOLE CONNECTION NOMINAL PIPE SIZE DESIGNATES THE SIZE OF THE NOMINAL DIAMETER OF THE DRAIN HOLE CONNECTION PIPE. 1D AND 1B MODE REPLY11AA05 CGMHD 13SCREW THREAD SERIES DESIGNATOR,INTERNAL INTERNAL SCREW THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF INTERNAL SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CGMJD 13THREAD DIRECTION,INTERNAL INTERNAL THREAD DIRECTION THE DIRECTION OF THE INTERNAL THREAD WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AA38 CGMKA 13THREAD SIZE,END,MALE MALE END THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED MALE END. 1A MODE REPLY 0 CGMLD 13SCREW THREAD SERIES DESIGNATOR,END,MALE MALE END SCREW THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF MALE END SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CGMMJ T13THREAD PITCH DIAMETERS,END,MALE MALE END THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A MALE END STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 CGMND 13THREAD DIRECTION,END,MALE MALE END THREAD DIRECTION THE DIRECTION OF THE MALE END THREAD WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AA38 CGMPJ 04THREAD LENGTH,END,MALE MALE END THREAD LENGTH A MEASUREMENT OF THE EXTENT OF THE MALE END COMPLETE (FULL) THREADS ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS. 2D AND 1B MODE REPLY21AA051AC20 CGMQA 13THREAD SIZE,END,FEMALE FEMALE END THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED FEMALE END. 1A MODE REPLY 0 CGMRD 13SCREW THREAD SERIES DESIGNATOR,END,FEMALE FEMALE END SCREW THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF FEMALE THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CGMSJ T13THREAD PITCH DIAMETERS,END,FEMALE FEMALE END THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A FEMALE END STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 CGMTD 13THREAD DIRECTION,END,FEMALE FEMALE END THREAD DIRECTION THE DIRECTION OF THE FEMALE END THREAD WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AA38 CGMWJ 04THREAD LENGTH,END,FEMALE FEMALE END THREAD LENGTH A MEASUREMENT OF THE EXTENT OF FEMALE END COMPLETE (FULL) THREADS ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS. 2D AND 1B MODE REPLY21AA051AC20 CGMXD /D/ 07STUD,MOUNTING,INTEGRAL INTEGRAL MOUNTING STUD AN INDICATION OF WHETHER OR NOT AN INTEGRAL MOUNTING STUD IS INCLUDED. SELECT REPLY CODE 10AA49 CGMYD /D/ 07FEATURE,DESIGN,SPECIAL SPECIAL DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A SPECIAL DESIGN FEATURE IS REQUIRED. SELECT REPLY CODE 10AE40 CGMZG 04SIZE ACCOMMODATED,PIPE PIPE SIZE ACCOMMODATED DESIGNATES THE PIPE SIZE THE ITEM WILL ACCOMMODATE. FULL TEXT WRITE-IN 0 CGNBD /D/ 09MATERIAL,SEAT,GROUND JOINT GROUND JOINT SEAT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE GROUND JOINT SEAT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC CYBM IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 CGNCD /D/ 07FEATURE,END,MALE MALE END FEATURE AN INDICATION OF WHETHER OR NOT A MALE END FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CGNDA 13THREAD SIZE,END,UNION UNION END THREAD SIZE DESIGNATES THE UNION END THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE. 1A MODE REPLY 0 CGNFD 13SCREW THREAD SERIES DESIGNATOR,END,UNION UNION END SCREW THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF UNION END SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CGNGD 13THREAD DIRECTION,END,UNION UNION END THREAD DIRECTION THE DIRECTION OF THE UNION END THREAD WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AA38 CGNHD /D/ 07FEATURE,BULKHEAD BULKHEAD FEATURE AN INDICATION OF WHETHER OR NOT A BULKHEAD FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CGNJD /D/ 07FLANGE,RETAINING,NUT NUT RETAINING FLANGE AN INDICATION OF WHETHER OR NOT A NUT RETAINING FLANGE IS INCLUDED. SELECT REPLY CODE 10AA49 CGNKJ 04DIAMETER,OUTSIDE,UNION UNION OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE UNION,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CGNLA 12QUANTITY,HOLE,BOLT,END END BOLT HOLE QUANTITY THE NUMBER OF BOLT HOLES PROVIDED ON THE END OF THE ITEM. 1A MODE REPLY 0 CGNMJ 04DIAMETER,HOLE,BOLT,END END BOLT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE END BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CGNND /D/ 14SHAPE,OPENING,CENTER CENTER OPENING SHAPE THE PHYSICAL CONFIGURATION OF THE CENTER OPENING. SELECT REPLY CODE 10AD07 CGNPJ /D/ 04LENGTH,INSIDE,CENTER OPENING CENTER OPENING INSIDE LENGTH A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF THE CENTER OPENING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CGNQJ /D/ 04WIDTH,INSIDE,CENTER OPENING CENTER OPENING INSIDE WIDTH AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CENTER OPENING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CGNRJ T10RANGE,ADJUSTMENT,HEIGHT HEIGHT ADJUSTMENT RANGE THE MINIMUM AND MAXIMUM HEIGHT LIMITS TO WHICH THE ITEM MAY BE ADJUSTED. 1D AND 1F MODE REPLY11AA05 CGNTA 12QUANTITY,CHOCK CHOCK QUANTITY THE NUMBER OF CHOCKS PROVIDED. 1A MODE REPLY 0 CGNWD /D/ 07RAMP,LOADING LOADING RAMP AN INDICATION OF WHETHER OR NOT A LOADING RAMP(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CGNXJ 04DISTANCE FROM BODY FRONT TO DRAWBAR COUPLER CENTER DISTANCE FROM BODY FRONT TO DRAWBAR COUPLER CENTER THE DISTANCE FROM THE FRONT OF THE BODY TO THE CENTER OF THE DRAWBAR COUPLER. 2D AND 1B MODE REPLY21AA051AC20 CGNYD 18TYPE,WHEEL,FIFTH FIFTH WHEEL TYPE INDICATES THE TYPE OF FIFTH WHEEL PROVIDED ON THE ITEM. SELECT REPLY CODE 10AK54 CGNZJ 04DISTANCE FROM DRAWBAR COUPLER CENTER TO WHEEL CENTERLINE DISTANCE FROM DRAWBAR COUPLER CENTER TO WHEEL CENTERLINE THE DISTANCE FROM THE CENTER OF THE DRAWBAR COUPLER TO THE WHEEL CENTERLINE. 2D AND 1B MODE REPLY21AA051AC20 CGPBD 18TYPE,DRAWBAR,DOLLY DOLLY DRAWBAR TYPE INDICATES THE TYPE OF DRAWBAR INCLUDED WITH THE DOLLY. SELECT REPLY CODE 10AK54 CGPCD 19CHARACTERISTIC,DRAWBAR,DOLLY DOLLY DRAWBAR CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC(S) OF THE DOLLY DRAWBAR. SELECT REPLY CODE 10AH28 CGPDD 18TYPE,COUPLER,DRAWBAR,DOLLY DOLLY DRAWBAR COUPLER TYPE INDICATES THE TYPE OF DOLLY DRAWBAR COUPLER PROVIDED. SELECT REPLY CODE 10AH98 CGPFD 18TYPE,BRAKE,SERVICE SERVICE BRAKE TYPE INDICATES THE TYPE OF SERVICE BRAKE(S) PROVIDED ON THE ITEM. SELECT REPLY CODE 10AG25 CGPGD 19CHARACTERISTIC,DRAWBAR DRAWBAR CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC(S) OF THE DRAWBAR. SELECT REPLY CODE 10AH28 CGPHD 18TYPE,COUPLER,DRAWBAR DRAWBAR COUPLER TYPE INDICATES THE TYPE OF DRAWBAR COUPLER PROVIDED. SELECT REPLY CODE 10AH98 CGPJD 18TYPE,SUPPORT,AUXILIARY AUXILIARY SUPPORT TYPE INDICATES THE TYPE OF AUXILIARY SUPPORT(S) INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AM61 CGPKD /D/ 07HOOK,PINTLE,TOWING TOWING PINTLE HOOK AN INDICATION OF WHETHER OR NOT A TOWING PINTLE HOOK(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CGPLJ A08LOCATION AND QUANTITY,DOOR DOOR LOCATION AND QUANTITY INDICATES THE LOCATION AND NUMBER OF DOORS INCLUDED. 1D AND 1A MODE REPLY13AJ91 CGPMD /D/ 08LOCATION,OPENING,HORIZONTAL,BODY BODY HORIZONTAL OPENING LOCATION INDICATES THE LOCATION OF THE HORIZONTAL OPENING(S) IN THE BODY. SELECT REPLY CODE 10AJ91 CGPND 14SHAPE,FRONT,BODY BODY FRONT SHAPE THE PHYSICAL CONFIGURATION OF THE FRONT OF THE BODY. SELECT REPLY CODE 10AD07 CGPPD 07ADJUSTABILITY,HEIGHT,PLATFORM LOADING PLATFORM LOADING HEIGHT ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE PLATFORM LOADING HEIGHT IS ADJUSTABLE. SELECT REPLY CODE 10AB00 CGPQJ A08LOCATION AND QUANTITY,WINDOW WINDOW LOCATION AND QUANTITY INDICATES THE LOCATION AND NUMBER OF WINDOWS INCLUDED. 1D AND 1A MODE REPLY13AJ91 CGPRD /D/ 07OUTLET,ELECTRIC,INTERIOR INTERIOR ELECTRIC OUTLET AN INDICATION OF WHETHER OR NOT AN INTERIOR ELECTRIC OUTLET(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CGPSJ /D/ 10WEIGHT,GROSS,VEHICLE VEHICLE GROSS WEIGHT THE TOTAL WEIGHT OF THE VEHICLE FULLY EQUIPPED. 1D AND 1B MODE REPLY12AG67 CGPTD /D/ 19FACILITY,HANGING,MEAT MEAT HANGING FACILITY AN INDICATION OF THE FACILITY/IES/ PROVIDED FOR HANGING MEAT. SELECT REPLY CODE 10AK54 CGPWG 10TEMP AT SPECIFIED OUTSIDE TEMP,INSIDE,MAINTAINED MAINTAINED INSIDE TEMP AT SPECIFIED OUTSIDE TEMP THE INSIDE TEMPERATURE THAT CAN BE MAINTAINED AT A SPECIFIED OUTSIDE TEMPERATURE. FULL TEXT WRITE-IN 0 CGPXD 18TYPE,REFRIGERANT,REFRIGERATING UNIT REFRIGERATING UNIT REFRIGERANT TYPE INDICATES THE TYPE OF REFRIGERANT CONTAINED IN THE REFRIGERATING UNIT. SELECT REPLY CODE 10AB75 CGPYD 11METHOD,COOLING,CONDENSER,REFRIGERATING UNIT REFRIGERATING UNIT CONDENSER COOLING METHOD THE COOLING MEANS USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE REFRIGERATING UNIT CONDENSER. SELECT REPLY CODE 10AN05 CGPZD /D/ 07ENGINE,GASOLINE,REFRIGERATING UNIT REFRIGERATING UNIT GASOLINE ENGINE AN INDICATION OF WHETHER OR NOT A REFRIGERATING UNIT GASOLINE ENGINE IS INCLUDED. SELECT REPLY CODE 10AA49 CGQBD /D/ 07MOTOR,ELECTRIC,REFRIGERATING UNIT REFRIGERATING UNIT ELECTRIC MOTOR AN INDICATION OF WHETHER OR NOT A REFRIGERATING UNIT ELECTRIC MOTOR IS INCLUDED. SELECT REPLY CODE 10AA49 CGQCA 12QUANTITY,SHEATH SHEATH QUANTITY THE NUMBER OF INDIVIDUAL SHEATHS PROVIDED. 1A MODE REPLY 0 CGQDD 08LOCATION,MOUNTING,REFRIGERATING UNIT REFRIGERATING UNIT MOUNTING LOCATION INDICATES THE MOUNTING LOCATION OF THE REFRIGERATING UNIT. SELECT REPLY CODE 10AJ91 CGQFD /D/ 07UNIT,REFRIGERATING REFRIGERATING UNIT AN INDICATION OF WHETHER OR NOT A REFRIGERATING UNIT IS INCLUDED. SELECT REPLY CODE 10AA49 CGQGJ 10SIZE,SYSTEM,PIPING PIPING SYSTEM SIZE THE NUMERIC SIZE DESIGNATION OF THE PIPING SYSTEM. 2D AND 1B MODE REPLY21AA051AC20 CGQHD 11METHOD,OPERATION,PUMP PUMP OPERATION METHOD THE MEANS USED TO OPERATE THE PUMP. SELECT REPLY CODE 10AC58 CGQJJ /D/ 10CAPACITY RATING FOR WHICH DESIGNED,PONTON PONTON CAPACITY RATING FOR WHICH DESIGNED THE RATED CAPACITY OF THE PONTON FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY12AG67 CGQKD /D/ 07CHEST,EQUIPMENT,GOOSENECK GOOSENECK EQUIPMENT CHEST AN INDICATION OF WHETHER OR NOT A GOOSENECK EQUIPMENT CHEST IS INCLUDED. SELECT REPLY CODE 10AA49 CGQLD /D/ 07SUPPORT,PONTON,GOOSENECK GOOSENECK PONTON SUPPORT AN INDICATION OF WHETHER OR NOT A GOOSENECK PONTON SUPPORT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CGQMJ 04HEIGHT,PLATFORM,LOAD LOAD PLATFORM HEIGHT A MEASUREMENT OF THE DISTANCE FROM GROUND LEVEL TO THE LOAD PLATFORM. 2D AND 1B MODE REPLY21AA051AC20 CGQND /D/ 09MATERIAL,PADDING,SHOULDER SHOULDER PADDING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHOULDER PADDING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGQPG /D/ 08LOCATION,OPENING,ARMOR PLATE INSERTION ARMOR PLATE INSERTION OPENING LOCATION INDICATES THE LOCATION OF THE OPENINGS FOR THE INSERTION OF THE ARMOR PLATES IN OR ON THE ITEM. FULL TEXT WRITE-IN 0 CGQQD /D/ 11METHOD,CLOSING,CASING CASING CLOSING METHOD THE MEANS BY WHICH THE CASING OPENING IS CLOSED. SELECT REPLY CODE 10AF69 CGQRD /D/ 07POCKET,UTILITY UTILITY POCKET AN INDICATION OF WHETHER OR NOT A UTILITY POCKET(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CGQSD /D/ 08LOCATION,COMPARTMENT,UTILITY POCKET PENCIL UTILITY POCKET PENCIL COMPARTMENT LOCATION INDICATES THE LOCATION OF THE COMPARTMENT IN OR ON THE UTILITY POCKET. SELECT REPLY CODE 10AJ91 CGQTG /D/ 11METHOD,ADJUSTMENT ADJUSTMENT METHOD THE MEANS PROVIDED TO ADJUST AN ITEM. FULL TEXT WRITE-IN 0 CGQWG /D/ 11METHOD,CLOSURE,SHOULDER STRAP SHOULDER STRAP CLOSURE METHOD THE MEANS PROVIDED TO CLOSE THE SHOULDER STRAP. FULL TEXT WRITE-IN 0 CGQXG /D/ 11METHOD,CLOSING,WAIST WAIST CLOSING METHOD THE MEANS PROVIDED TO CLOSE THE WAIST OPENING. FULL TEXT WRITE-IN 0 CGQYD /D/ 07PLATE,ARMOR ARMOR PLATE AN INDICATION OF WHETHER OR NOT AN ARMOR PLATE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CGQZD /D/ 09MATERIAL,PLATE,ARMOR ARMOR PLATE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ARMOR PLATE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGRBD /D/ 08LOCATION,PLATE,ARMOR ARMOR PLATE LOCATION INDICATES THE LOCATION OF THE ARMOR PLATE IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 CGRCD /D/ 07FEATURE,DESIGN,CLOSE PROXIMITY TO HIGH TEMP FIRE CLOSE PROXIMITY TO HIGH TEMP FIRE DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A DESIGN FEATURE FOR USE IN CLOSE PROXIMITY TO HIGH TEMPERATURE FIRE IS INCLUDED. SELECT REPLY CODE 10AA49 CGRDD /D/ 09MATERIAL,OUTSIDE OUTSIDE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE OUTSIDE MATERIAL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGRFD /D/ 07BACK,BELLOWS BELLOWS BACK AN INDICATION OF WHETHER OR NOT A BELLOWS BACK IS INCLUDED. SELECT REPLY CODE 10AA49 CGRGD /D/ 08LOCATION,PART,LEATHER,GLOVE OUTSIDE GLOVE OUTSIDE LEATHER PART LOCATION INDICATES THE LOCATION OF THE LEATHER PART(S) ON THE OUTSIDE OF THE GLOVE(S). SELECT REPLY CODE 10AJ91 CGRHD /D/ 19DEGREE,LINING,GLOVE GLOVE LINING DEGREE THE EXTENT OF THE LINING WHICH COVERS THE INNER SURFACE OF THE GLOVE(S). SELECT REPLY CODE 10AF86 CGRJD /D/ 09MATERIAL,LINING,GLOVE GLOVE LINING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE GLOVE LINING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGRKD /D/ 08LOCATION,STRAP,SIZE TAKEUP ADJUSTMENT SIZE TAKEUP ADJUSTMENT STRAP LOCATION INDICATES THE LOCATION OF THE SIZE TAKEUP ADJUSTMENT STRAP/S/ IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 CGRLD /D/ 11METHOD,CLOSING,SLEEVE/LEG SLEEVE/LEG CLOSING METHOD THE MEANS BY WHICH THE SLEEVE(S) AND/OR LEG OPENING(S) IS CLOSED. SELECT REPLY CODE 10AF69 CGRMD /D/ 07STRAPS,SECURING,WRIST/ANKLE WRIST/ANKLE SECURING STRAPS AN INDICATION OF WHETHER OR NOT SECURING STRAPS AT THE WRISTS AND/OR ANKLES ARE INCLUDED. SELECT REPLY CODE 10AA49 CGRND /D/ 09MATERIAL,FRONT,SHIRT SHIRT FRONT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHIRT FRONT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGRPD /D/ 09MATERIAL,PANEL,SHIRT CENTER BACK SHIRT CENTER BACK PANEL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHIRT CENTER BACK PANEL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGRQD /D/ 09MATERIAL,INSERT,SHIRT SIDE BACK SHIRT SIDE BACK INSERT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHIRT SIDE BACK INSERT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGRRA /D/ 12QUANTITY,POCKET,SHIRT SHIRT POCKET QUANTITY THE NUMBER OF SHIRT POCKETS INCLUDED. 1A MODE REPLY 0 CGRSD /D/ 18TYPE,POCKET,SHIRT SHIRT POCKET TYPE INDICATES THE TYPE OF SHIRT POCKET BY THE STYLE OR DESIGN. SELECT REPLY CODE 10AF87 CGRTD /D/ 07FLAP,POCKET,SHIRT SHIRT POCKET FLAP AN INDICATION OF WHETHER OR NOT A SHIRT POCKET FLAP(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CGRWD /D/ 11METHOD,CLOSING,SHIRT POCKET SHIRT POCKET CLOSING METHOD THE MEANS BY WHICH THE SHIRT POCKET OPENING/S/ IS CLOSED. SELECT REPLY CODE 10AF69 CGRXD /D/ 08LOCATION,POCKET,SHIRT SHIRT POCKET LOCATION INDICATES THE LOCATION OF THE SHIRT POCKET(S) IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 CGRYD /D/ 18TYPE,END,SLEEVE SLEEVE END TYPE INDICATES THE TYPE OF SLEEVE END BY THE STYLE OR FINISH. SELECT REPLY CODE 10AK84 CGRZD /D/ 01COLOR,SHIRT SHIRT COLOR THE HUE OR TINT OF THE SHIRT. SELECT REPLY CODE 10AD06 CGSBD /D/ 19SOURCE,SHADE,SHIRT SHIRT SHADE SOURCE THE NAME OF THE REFERENCE SOURCE OF THE SHIRT SHADE IDENTIFICATION DESIGNATOR. SELECT REPLY CODE 10AF94 CGSCA /D/ 19IDENTIFICATION,SHADE,SHIRT SHIRT SHADE IDENTIFICATION A DESIGNATION ASSIGNED TO A PARTICULAR GRADATION OF A COLOR FOR PURPOSE OF READY IDENTIFICATION OF THE SHIRT. 1A MODE REPLY 0 CGSDD /D/ 18TYPE,TROUSERS TROUSERS TYPE INDICATES THE TYPE OF TROUSERS BY THE STYLE OR DESIGN. SELECT REPLY CODE 10AH80 CGSFD /D/ 09MATERIAL,TROUSERS TROUSERS MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TROUSERS ARE FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGSGG /D/ 19SPEC/STD,FILTER,GAS/PARTICULATE GAS/PARTICULATE FILTER SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE GAS AND PARTICULATE FILTER. FULL TEXT WRITE-IN 0 CGSHA 19NUMBER,MODEL,GAS FILTER GAS FILTER MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE GAS FILTER. 1A MODE REPLY 0 CGSJG 19SPEC/STD,FILTER,GAS GAS FILTER SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE GAS FILTER. FULL TEXT WRITE-IN 0 CGSKD /D/ 11METHOD,CLOSING,TROUSERS POCKET TROUSERS POCKET CLOSING METHOD THE MEANS BY WHICH THE TROUSERS POCKET OPENING/S/ IS CLOSED. SELECT REPLY CODE 10AF69 CGSLD /D/ 07LOOP,BELT,TROUSERS TROUSERS BELT LOOP AN INDICATION OF WHETHER OR NOT A BELT LOOP(S) IS INCLUDED ON THE TROUSERS. SELECT REPLY CODE 10AA49 CGSMD /D/ 07BOTTOMS,FINISHED,TROUSERS TROUSERS FINISHED BOTTOMS AN INDICATION OF WHETHER OR NOT FINISHED BOTTOMS ARE INCLUDED ON THE TROUSERS. SELECT REPLY CODE 10AA49 CGSNG 19STUDY COVERED,FIELD FIELD STUDY COVERED AN INDICATION OF THE FIELD OF STUDY COVERED BY THE ITEM. FULL TEXT WRITE-IN 0 CGSPD 11METHOD,OPERATION,ACCESS ACCESS OPERATION METHOD THE MEANS USED TO OPERATE THE ACCESS. SELECT REPLY CODE 10AC58 CGSQG 19TIP AND QUANTITY,SUPPLY SUPPLY TIP AND QUANTITY A LISTING OF THOSE TIPS WHICH ARE COMPRISED OF A NATIONAL STOCK NUMBER,AN ITEM NAME,STANDARDIZED NAME,OR PART NAME,AND THE NUMBER OF EACH. FULL TEXT WRITE-IN 0 CGSRG 19TIP AND QUANTITY,NONSUPPLY NONSUPPLY TIP AND QUANTITY A LISTING OF THOSE TIPS,OUTSIDE THE SCOPE OF AN ITEM OF SUPPLY TO BE CATALOGED,AS INDICATED BY THE NAME OF THE MANUFACTURER,AND THE NAME AND NUMBER OF THE ITEM AS IDENTIFIED BY THE MANUFACTURER,AND THE NUMBER OF EACH. FULL TEXT WRITE-IN 0 CGSSG 19BACK,PRINTED,SPECIAL SPECIAL PRINTED BACK AN INDICATION OF THE SPECIAL PRINTING ON THE BACK/S/ OF THE ITEM. FULL TEXT WRITE-IN 0 CGSTJ 04LENGTH,CARD CARD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CARD,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CGSWJ 04WIDTH,CARD CARD WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CARD,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CGSXD /D/ 18TYPE,ADAPTER,OUTLET OUTLET ADAPTER TYPE INDICATES THE TYPE OF OUTLET ADAPTER PROVIDED. SELECT REPLY CODE 10AL20 CGSYG /D/ 12LENGTH AND QUANTITY,TUBE,PLASTIC PLASTIC TUBE LENGTH AND QUANTITY A MEASUREMENT OF THE LONGEST DIMENSION OF THE PLASTIC TUBE AND THE NUMBER OF EACH. FULL TEXT WRITE-IN 0 CGSZD /D/ 19MARKING,PASSAGEWAY PASSAGEWAY MARKING AN INDICATION OF THE PASSAGEWAY MARKING(S). SELECT REPLY CODE 10AN52 CGTBD /D/ 19ACTION UNDER PRESSURE,PASSAGEWAY PASSAGEWAY ACTION UNDER PRESSURE THE ACTION THAT TAKES PLACE IN THE PASSAGEWAY WHEN PRESSURE IS APPLIED. SELECT REPLY CODE 10AD21 CGTCD /D/ 19ACTION UNDER SUCTION,PASSAGEWAY PASSAGEWAY ACTION UNDER SUCTION THE ACTION THAT TAKES PLACE IN THE PASSAGEWAY WHEN SUCTION IS APPLIED. SELECT REPLY CODE 10AD21 CGTDD /D/ 19SIMULATED,AREA,BODY BODY AREA SIMULATED AN INDICATION OF THAT PORTION OF THE BODY THE ITEM SIMULATES. SELECT REPLY CODE 10AE98 CGTFD 03DESIGNATION,SEX SEX DESIGNATION DESIGNATES THE SEX OF THE ITEM. SELECT REPLY CODE 10AJ60 CGTGD /D/ 07JAW,HEAD/ARTICULATED,MOVABLE MOVABLE HEAD/ARTICULATED JAW AN INDICATION OF WHETHER OR NOT A MOVABLE HEAD AND AN ARTICULATED JAW IS INCLUDED. SELECT REPLY CODE 10AA49 CGTHD /D/ 07REACTION,BREASTBONE,UNCONSCIOUS UNCONSCIOUS BREASTBONE REACTION AN INDICATION OF WHETHER OR NOT AN UNCONSCIOUS BREASTBONE REACTION IS INCLUDED. SELECT REPLY CODE 10AA49 CGTJD /D/ 07ATTACHMENT TO SIMULATE CAROTID PULSE PRESSURE ATTACHMENT TO SIMULATE CAROTID PULSE PRESSURE AN INDICATION OF WHETHER OR NOT AN ATTACHMENT TO SIMULATE CAROTID PULSE PRESSURE IS INCLUDED. SELECT REPLY CODE 10AA49 CGTKG 11METHOD AND QUANTITY,ATTACHMENT ATTACHMENT METHOD AND QUANTITY THE MEANS USED TO ATTACH THE ITEM AND THE NUMBER OF EACH. FULL TEXT WRITE-IN 0 CGTLD /D/ 18TYPE,MATERIAL,CONTENT CONTENT MATERIAL TYPE INDICATES THE TYPE OF MATERIAL COMPOSING THE CONTENT. SELECT REPLY CODE 10AN48 CGTMD /D/ 07STERILITY,MATERIAL,CONTENT CONTENT MATERIAL STERILITY AN INDICATION OF WHETHER OR NOT THE MATERIAL CONTENT IS FREE OF LIVING ORGANISMS. SELECT REPLY CODE 10AG96 CGTND /D/ 07FEATURE,USAGE,PARENTERAL PARENTERAL USAGE FEATURE AN INDICATION OF WHETHER OR NOT A PARENTERAL USAGE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CGTPJ 10CAPACITY,FLUID FLUID CAPACITY THE AMOUNT OF FLUID THE ITEM IS DESIGNED TO HOLD. 1D AND 1B MODE REPLY12AG67 CGTQD /D/ 07STYLET,WIRE WIRE STYLET AN INDICATION OF WHETHER OR NOT A WIRE STYLET IS INCLUDED. SELECT REPLY CODE 10AA49 CGTRD /D/ 07COVER,NEEDLE NEEDLE COVER AN INDICATION OF WHETHER OR NOT A NEEDLE COVER IS INCLUDED. SELECT REPLY CODE 10AA49 CGTSD 19COMPONENT,CONVEYING CONVEYING COMPONENT AN INDICATION OF THE CONVEYING COMPONENT(S) PROVIDED. SELECT REPLY CODE 10AM42 CGTTJ /D/ 10FREQUENCY AT WHICH IMPEDANCE RATING APPLIES PER FUNCTION FREQUENCY AT WHICH IMPEDANCE RATING APPLIES PER FUNCTION THE NUMBER OF PULSES OR THE FREQUENCY AT WHICH THE IMPEDANCE OF AN ITEM IS MEASURED PER FUNCTION. 2D AND 1B MODE REPLY21AE062AH19 CGTWJ 10CAPACITY,MAXIMUM,SHOVEL SHOVEL MAXIMUM CAPACITY THE MAXIMUM CAPACITY OF THE SHOVEL. 1D AND 1B MODE REPLY12AG67 CGTXJ 10LIFTING CAPACITY,MAXIMUM MAXIMUM LIFTING CAPACITY THE MAXIMUM WEIGHT THAT THE ITEM IS DESIGNED TO LIFT. 1D AND 1B MODE REPLY12AG67 CGTYJ 04LENGTH AT WHICH LIFTING CAPACITY IS RATED,BOOM BOOM LENGTH AT WHICH LIFTING CAPACITY IS RATED A MEASUREMENT OF THE BOOM LENGTH AT WHICH THE LIFTING CAPACITY IS RATED. 2D AND 1B MODE REPLY21AA051AC20 CGTZJ 04RADIUS AT WHICH LIFTING CAPACITY IS RATED,BOOM BOOM RADIUS AT WHICH LIFTING CAPACITY IS RATED A MEASUREMENT OF THE BOOM RADIUS AT WHICH THE LIFTING CAPACITY IS RATED. 2D AND 1B MODE REPLY21AA051AC20 CGWBD 19POSITION AT WHICH LIFTING CAPACITY IS RATED,OUTRIGGER OUTRIGGER POSITION AT WHICH LIFTING CAPACITY IS RATED AN INDICATION OF THE OUTRIGGER POSITION AT WHICH THE LIFTING CAPACITY IS RATED. SELECT REPLY CODE 10AB00 CGWCJ 10CAPACITY,MAXIMUM,BACKHOE BACKHOE MAXIMUM CAPACITY THE MAXIMUM CAPACITY OF THE BACKHOE. 1D AND 1B MODE REPLY12AG67 CGWDD 18TYPE,ENGINE,CRANE CRANE ENGINE TYPE INDICATES THE TYPE OF CRANE ENGINE PROVIDED. SELECT REPLY CODE 10AG27 CGWFJ 04LENGTH,OVERALL,BOOM BOOM OVERALL LENGTH THE LONGEST DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BOOM. 2D AND 1B MODE REPLY21AA051AC20 CGWGB 04ANGLE IN DEG,MAXIMUM,BOOM BOOM MAXIMUM ANGLE IN DEG THE MAXIMUM BOOM ANGLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CGWHD /D/ 07FEATURE,ROTATION,CONTINUOUS,BOOM BOOM CONTINUOUS ROTATION FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE THAT PERMITS CONTINUOUS ROTATION OF THE BOOM IS INCLUDED. SELECT REPLY CODE 10AA49 CGWJB 10RATATION IN DEG,MAXIMUM,BOOM BOOM MAXIMUM ROTATION IN DEG THE MAXIMUM BOOM ROTATION,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CGWKD 18TYPE,EXTENSION,BOOM BOOM EXTENSION TYPE INDICATES THE TYPE OF BOOM EXTENSION PROVIDED. SELECT REPLY CODE 10AK95 CGWLA 12QUANTITY,WHEEL,REAR DRIVE REAR DRIVE WHEEL QUANTITY THE NUMBER OF REAR DRIVE WHEELS PROVIDED ON THE ITEM. 1A MODE REPLY 0 CGWMA 12QUANTITY,WHEEL,FRONT DRIVE FRONT DRIVE WHEEL QUANTITY THE NUMBER OF FRONT DRIVE WHEELS PROVIDED ON THE ITEM. 1A MODE REPLY 0 CGWND /D/ 11METHOD,CLOSING,DROP SEAT DROP SEAT CLOSING METHOD THE MEANS BY WHICH THE DROP SEAT OPENING IS CLOSED. SELECT REPLY CODE 10AF69 CGWPD /D/ 01COLOR,TROUSERS TROUSERS COLOR THE HUE OR TINT OF THE TROUSERS. SELECT REPLY CODE 10AD06 CGWQD /D/ 19SOURCE,SHADE,TROUSERS TROUSERS SHADE SOURCE THE NAME OF THE REFERENCE SOURCE OF THE TROUSERS SHADE IDENTIFICATION DESIGNATOR. SELECT REPLY CODE 10AF94 CGWRA /D/ 19IDENTIFICATION,SHADE,TROUSERS TROUSERS SHADE IDENTIFICATION A DESIGNATION ASSIGNED TO A PARTICULAR GRADATION OF A COLOR FOR PURPOSE OF READY IDENTIFICATION OF THE TROUSERS. 1A MODE REPLY 0 CGWSD /D/ 11METHOD,CLOSING,TROUSERS FRONT FLY TROUSERS FRONT FLY CLOSING METHOD THE MEANS OF CLOSING THE TROUSERS FRONT FLY OPENING. SELECT REPLY CODE 10AF69 CGWTD /D/ 04LENGTH,LEG,TROUSERS TROUSERS LEG LENGTH THE LENGTH OF THE TROUSERS LEGS WITH REFERENCE TO THE PART OF THE BODY THE TROUSERS REACHES. SELECT REPLY CODE 10AF68 CGWWD /D/ 11METHOD,ADJUSTMENT,TROUSERS WAIST TROUSERS WAIST ADJUSTMENT METHOD THE MEANS PROVIDED TO ADJUST THE FIT OF THE TROUSERS AT THE WAIST. SELECT REPLY CODE 10AL41 CGWXG /D/ 18TYPE,BUREAU OF MINES BUREAU OF MINES TYPE INDICATES THE TYPE AS DESIGNATED BY THE BUREAU OF MINES. FULL TEXT WRITE-IN 0 CGWYD /D/ 07DESICCANT DESICCANT AN INDICATION OF WHETHER OR NOT DESICCANT IS INCLUDED. SELECT REPLY CODE 10AA49 CGWZA /D/ 19NUMBER,MODEL,GAS/PARTICULATE FILTER GAS/PARTICULATE FILTER MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE GAS AND PARTICULATE FILTER. 1A MODE REPLY 0 CGXBA 19NUMBER,MODEL,PARTICULATE FILTER PARTICULATE FILTER MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE PARTICULATE FILTER. 1A MODE REPLY 0 CGXCG 19SPEC/STD,FILTER,PARTICULATE PARTICULATE FILTER SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE PARTICULATE FILTER. FULL TEXT WRITE-IN 0 CGXDA 12QUANTITY,CYCLE,ENGINE ENGINE CYCLE QUANTITY THE NUMBER OF ENGINE CYCLES PROVIDED. 1A MODE REPLY 0 CGXFJ A19DEVICE AND QUANTITY ACCOMMODATED,PROTECTIVE,INDIVIDUAL INDIVIDUAL PROTECTIVE DEVICE AND QUANTITY ACCOMMODATED THE INDIVIDUAL PROTECTIVE DEVICE AND THE NUMBER THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1A MODE REPLY12AH83 CGXGD /D/ 07MASK,FACE FACE MASK AN INDICATION OF WHETHER OR NOT A FACE MASK IS INCLUDED. SELECT REPLY CODE 10AA49 CGXHD /D/ 07HEADPIECE HEADPIECE AN INDICATION OF WHETHER OR NOT A HEADPIECE IS INCLUDED. SELECT REPLY CODE 10AA49 CGXJD /D/ 07HEATER,AIR AIR HEATER AN INDICATION OF WHETHER OR NOT AN AIR HEATER(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CGXKD 02DESIGN,USAGE,BLOWER ASSEMBLY BLOWER ASSEMBLY USAGE DESIGN THE DESIGNED USE OF THE BLOWER ASSEMBLY. SELECT REPLY CODE 10AH21 CGXLD 07SHIELD,RAIN RAIN SHIELD AN INDICATION OF WHETHER OR NOT A RAIN SHIELD IS REQUIRED. SELECT REPLY CODE 10AE40 CGXMD /D/ 07KIT,INSTALLATION INSTALLATION KIT AN INDICATION OF WHETHER OR NOT AN INSTALLATION KIT IS INCLUDED. SELECT REPLY CODE 10AA49 CGXND /D/ 07KIT,TOOL TOOL KIT AN INDICATION OF WHETHER OR NOT A TOOL KIT IS INCLUDED. SELECT REPLY CODE 10AA49 CGXPJ A18TYPE AND QUANTITY,FILTER,FURNISHED FURNISHED FILTER TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF FILTERS FURNISHED. 1D AND 1A MODE REPLY12AH81 CGXQD 18TYPE,MASK MASK TYPE INDICATES THE TYPE OF MASK PROVIDED. SELECT REPLY CODE 10AK54 CGXRD 18TYPE,PROVISION,VISUAL VISUAL PROVISION TYPE INDICATES THE TYPE OF VISUAL PROVISION PROVIDED. SELECT REPLY CODE 10AC58 CGXSD /D/ 09MATERIAL,PROVISION,VISUAL VISUAL PROVISION MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE VISUAL PROVISION IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CGXTD /D/ 07HARNESS,HEAD HEAD HARNESS AN INDICATION OF WHETHER OR NOT A HEAD HARNESS IS INCLUDED. SELECT REPLY CODE 10AA49 CGXWD /D/ 07FEATURE,HARDENED,SPARE LENS SPARE LENS HARDENED FEATURE AN INDICATION OF WHETHER OR NOT A SPARE LENS/ES/ HARDENED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CGXXD /D/ 07STOPS,FLOOR FLOOR STOPS AN INDICATION OF WHETHER OR NOT FLOOR STOPS ARE INCLUDED. SELECT REPLY CODE 10AA49 CGXYD /D/ 07DEVICE,LOCKING,POSITION POSITION LOCKING DEVICE AN INDICATION OF WHETHER OR NOT A POSITION LOCKING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 CGXZJ 10CLEARANCE,RADIAL RADIAL CLEARANCE A MEASUREMENT OF THE RADIAL CLEARANCE OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CGYBD 07ADJUSTABILITY,POSITION,WORK HOLDING DEVICE WORK HOLDING DEVICE POSITION ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE POSITION OF THE WORK HOLDING DEVICE IS ADJUSTABLE. SELECT REPLY CODE 10AB00 CGYCD 18TYPE FOR WHICH DESIGNED,ENGINE,NONAIRCRAFT NONAIRCRAFT ENGINE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF NONAIRCRAFT ENGINE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AG27 CGYDG 19MODEL TESTED,ENGINE ENGINE MODEL TESTED THE DESIGNATION USED TO IDENTIFY THE ENGINE THE ITEM IS DESIGNED TO TEST. FULL TEXT WRITE-IN 0 CGYFD 18TYPE,SEMITRAILER SEMITRAILER TYPE INDICATES THE TYPE OF SEMITRAILER PROVIDED. SELECT REPLY CODE 10AK54 CGYGJ 10CAPACITY,SEMITRAILER SEMITRAILER CAPACITY THE CAPACITY OF THE SEMITRAILER. 1D AND 1B MODE REPLY12AG67 CGYHG 19NAME,MANUFACTURER,SEMITRAILER SEMITRAILER MANUFACTURER NAME THE NAME OF THE MANUFACTURER OF THE SEMITRAILER. FULL TEXT WRITE-IN 0 CGYJA 19NUMBER,IDENTIFYING,SEMITRAILER SEMITRAILER IDENTIFYING NUMBER THE NUMBER ASSIGNED TO THE SEMITRAILER FOR PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 CGYKD /D/ 07FEATURE,DESIGN,TESTING,ENGINE DRIVEN HYDRAULIC PUMP ENGINE DRIVEN HYDRAULIC PUMP TESTING DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A DESIGN FEATURE FOR TESTING ENGINE DRIVEN HYDRAULIC PUMPS IS INCLUDED. SELECT REPLY CODE 10AA49 CGYLJ 10CAPACITY RATING,FLOW FLOW CAPACITY RATING THE RATED FLOW CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 CGYMD /D/ 07SUBCIRCUIT,MANIFOLD,PRESSURE PRESSURE MANIFOLD SUBCIRCUIT AN INDICATION OF WHETHER OR NOT A PRESSURE MANIFOLD SUBCIRCUIT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CGYND /D/ 07SPACE,NAME NAME SPACE AN INDICATION OF WHETHER OR NOT A NAME SPACE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 CGYPA /D/ 12QUANTITY EXCLUDING NAME SPACE,COLUMN COLUMN QUANTITY EXCLUDING NAME SPACE THE NUMBER OF COLUMNS PROVIDED,EXCLUDING THE NAME SPACE. 1A MODE REPLY 0 CGYQJ 04DEPTH,FOLD FOLD DEPTH A MEASUREMENT OF THE DEPTH OF THE FOLD. 2D AND 1B MODE REPLY21AA051AC20 CGYRA 12QUANTITY PER FOLD,FORM FORM QUANTITY PER FOLD THE NUMBER OF FORMS IN EACH FOLD. 1A MODE REPLY 0 CGYSD 11METHOD,TRANSFER,COPY COPY TRANSFER METHOD THE MEANS OF TRANSFERRING THE COPY. SELECT REPLY CODE 10AK54 CGYTD 18TYPE,EXTRACTION,CARBON PAPER CARBON PAPER EXTRACTION TYPE INDICATES THE TYPE OF CARBON PAPER EXTRACTION. SELECT REPLY CODE 10AK54 CGYWD /D/ 07PERFORATIONS FOR SPROCKET FEED,MARGINAL MARGINAL PERFORATIONS FOR SPROCKET FEED AN INDICATION OF WHETHER OR NOT MARGINAL PERFORATIONS ARE INCLUDED FOR SPROCKET FEED. SELECT REPLY CODE 10AA49 CGYXD 19POSITION,OPENING,COVER COVER OPENING POSITION THE POSITION FROM WHICH THE COVER OPENS. SELECT REPLY CODE 10AJ91 CGYYA 12QUANTITY PER SET,PARTS PARTS QUANTITY PER SET THE NUMBER OF PARTS PER SET. 1A MODE REPLY 0 CGYZA 12QUANTITY,PARTS,GUMMED GUMMED PARTS QUANTITY THE NUMBER OF GUMMED PARTS PROVIDED. 1A MODE REPLY 0 CGZBD /D/ 19PARTS,GUMMED GUMMED PARTS AN INDICATION OF THE GUMMED PARTS. SELECT REPLY CODE 10AH91 CGZCA 12QUANTITY,ENVELOPE,TRANSPARENT TRANSPARENT ENVELOPE QUANTITY THE NUMBER OF TRANSPARENT ENVELOPES PROVIDED. 1A MODE REPLY 0 CGZDA /D/ 12QUANTITY,PAGE,NUMBERED NUMBERED PAGE QUANTITY THE TOTAL NUMBERED PAGES PROVIDED. 1A MODE REPLY 0 CGZFB 10DIVISION IN HOURS,INTERVAL,TIME TIME INTERVAL DIVISION IN HOURS THE NUMERIC VALUE INDICATING THE TIME INTERVAL DIVISION,EXPRESSED IN HOURS. 1B MODE REPLY 0 CGZGD 08LOCATION,INDEX INDEX LOCATION INDICATES THE LOCATION OF THE INDEX. SELECT REPLY CODE 10AJ91 CGZHD /D/ 07LEGEND AT TOP SHOWING DAY/MONTH,PRINTED PRINTED LEGEND AT TOP SHOWING DAY/MONTH AN INDICATION OF WHETHER OR NOT A PRINTED LEGEND AT THE TOP SHOWING THE DAY AND MONTH IS INCLUDED. SELECT REPLY CODE 10AA49 CGZJD /D/ 07FEATURE,LEAF,LOOSE LOOSE LEAF FEATURE AN INDICATION OF WHETHER OR NOT A LOOSE LEAF FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CGZKD 18TYPE,EXTRACTION,INTERLEAVED CARBON PAPER INTERLEAVED CARBON PAPER EXTRACTION TYPE INDICATES THE TYPE OF EXTRACTION PROVIDED FOR INTERLEAVED CARBON PAPER. SELECT REPLY CODE 10AK54 CGZLD /D/ 07PERFORATION,MARGINAL MARGINAL PERFORATION AN INDICATION OF WHETHER OR NOT A MARGINAL PERFORATION/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 CGZMJ /D/ 19DIMENSION AND LOCATION,MARGIN,PERFORMATED PERFORATED MARGIN DIMENSION AND LOCATION THE DIMENSION OF THE PERFORATED MARGIN AND LOCATION ON THE ITEM. 2D AND 1B MODE REPLY21AA053AJ91 CGZNJ /D/ 19DIMENSION AND LOCATION,MARGIN,CARBON PERFORATED CARBON PERFORATED MARGIN DIMENSION AND LOCATION THE DIMENSION OF THE CARBON PERFORATED MARGIN AND LOCATION ON THE ITEM. 2D AND 1B MODE REPLY21AA053AJ91 CGZPJ 04DISTANCE BETWEEN PERFORATIONS,HORIZONTAL HORIZONTAL DISTANCE BETWEEN PERFORATIONS THE DISTANCE FROM ONE PERFORATION TO THE NEXT ON A HORIZONTAL PLANE. 1D AND 1B MODE REPLY11AA05 CGZQA /D/ 12QUANTITY PER INCH,LINE,HORIZONTAL HORIZONTAL LINE QUANTITY PER INCH THE NUMBER OF HORIZONTAL LINES PER INCH. 1A MODE REPLY 0 CGZRA 12QUANTITY,LINE,VERTICAL VERTICAL LINE QUANTITY THE NUMBER OF VERTICAL LINES. 1A MODE REPLY 0 CGZSJ /D/ 04SPACING,FASTENER FASTENER SPACING AN INDICATION OF THE FASTENER SPACING. 1D AND 1B MODE REPLY11AA05 CGZTD 19SEQUENCE ACROSS TAPE WIDTH,PRINTED PRINTED SEQUENCE ACROSS TAPE WIDTH AN INDICATION OF THE PRINTED SEQUENCE ACROSS THE WIDTH OF THE TAPE. SELECT REPLY CODE 10AF81 CGZWD 19SEQUENCE ALONG TAPE LENGTH,PRINTED PRINTED SEQUENCE ALONG TAPE LENGTH AN INDICATION OF THE PRINTED SEQUENCE ALONG THE LENGTH OF THE TAPE. SELECT REPLY CODE 10AF81 CGZXA /D/ 12QUANTITY,SECTION,PRINTED PRINTED SECTION QUANTITY THE NUMBER OF PRINTED SECTIONS INCLUDED. 1A MODE REPLY 0 CGZYJ 04WIDTH,HORIZONTAL HORIZONTAL WIDTH THE HORIZONTAL WIDTH OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CGZZA 19YEAR FOR WHICH DESIGNED YEAR FOR WHICH DESIGNED THE YEAR FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 CHBBA 12QUANTITY,GUIDE,DIARY PLANNING DIARY PLANNING GUIDE QUANTITY THE NUMBER OF DIARY PLANNING GUIDES PROVIDED. 1A MODE REPLY 0 CHBCD /D/ 19MARKING,GUIDE,DIARY PLANNING DIARY PLANNING GUIDE MARKING AN INDICATION OF THE MARKING/S/ THAT APPEARS ON THE DIARY PLANNING GUIDE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. SELECT REPLY CODE 10AJ65 CHBDJ 04LENGTH,GUIDE,DIARY PLANNING DIARY PLANNING GUIDE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A DIARY PLANNING GUIDE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CHBFJ 04WIDTH,GUIDE,DIARY PLANNING DIARY PLANNING GUIDE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A DIARY PLANNING GUIDE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CHBGD 18TYPE,OPENING,DIARY PLANNING GUIDE DIARY PLANNING GUIDE OPENING TYPE INDICATES THE TYPE OF OPENING PROVIDED ON THE DIARY PLANNING GUIDE. SELECT REPLY CODE 10AK54 CHBHD /D/ 19MARKING,DIVIDER DIVIDER MARKING AN INDICATION OF THE MARKING(S) THAT APPEARS ON THE DIVIDER. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. SELECT REPLY CODE 10AJ65 CHBJJ /D/ 04LENGTH,DIVIDER DIVIDER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A DIVIDER,IN DISTINCTION FROM WIDTH. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 2D AND 1B MODE REPLY21AA051AC20 CHBKJ 04WIDTH,DIVIDER DIVIDER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE DIVIDER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CHBLA /D/ 03DESIGNATOR,CUT,DIVIDER DIVIDER CUT DESIGNATOR A DESIGNATOR THAT IDENTIFIES THE DIVIDER CUT. 1A MODE REPLY 0 CHBMD /D/ 09MATERIAL,WALLET WALLET MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WALLET IS FABRICATED. SELECT REPLY CODE 10AD09 CHBND /D/ 07TRACK,FITTED,LOADING RAMP LOADING RAMP FITTED TRACK AN INDICATION OF WHETHER OR NOT A FITTED TRACK(S) IS INCLUDED WITH THE LOADING RAMP(S). SELECT REPLY CODE 10AA49 CHBPJ /D/ 10GAGE,TRACK TRACK GAGE A MEASUREMENT OF THE WIDTH BETWEEN THE RAIL HEADS. 2D AND 1B MODE REPLY21AA051AC20 CHBQJ /D/ 10WEIGHT,RAIL RAIL WEIGHT A RELATIVE MEASURE OF THE MASS OF A RAIL WITH RESPECT TO ITS DENSITY. 1D AND 1B MODE REPLY12AG67 CHBRD /D/ 07POCKET,STAKE STAKE POCKET AN INDICATION OF WHETHER OR NOT A STAKE POCKET(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CHBSD /D/ 07FEATURE,DESIGN,TRANSPORTING CRANE SHOVEL ATTACHMENT TRANSPORTING CRANE SHOVEL ATTACHMENT DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A DESIGN FEATURE FOR TRANSPORTING CRANE SHOVEL ATTACHMENT IS INCLUDED. SELECT REPLY CODE 10AA49 CHBTJ 04LENGTH,GOOSENECK GOOSENECK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A GOOSENECK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CHBWD 18TYPE,GOOSENECK GOOSENECK TYPE INDICATES THE TYPE OF GOOSENECK PROVIDED. SELECT REPLY CODE 10AK54 CHBXD /D/ 07DECK,LOADING,GOOSENECK GOOSENECK LOADING DECK AN INDICATION OF WHETHER OR NOT A GOOSENECK LOADING DECK IS INCLUDED. SELECT REPLY CODE 10AA49 CHBYJ /D/ 10CAPACITY RATING,PULL/LIFT,WINCH WINCH PULL/LIFT CAPACITY RATING THE RATED CAPACITY THAT THE WINCH IS CAPABLE OF PULLING AND/OR LIFTING. 1D AND 1B MODE REPLY12AG67 CHBZD /D/ 19SOURCE,POWER,WINCH WINCH POWER SOURCE THE SOURCE OF POWER WHICH DRIVES THE WINCH. SELECT REPLY CODE 10AG27 CHCBD /D/ 07TIRE,SOLID SOLID TIRE AN INDICATION OF WHETHER OR NOT A SOLID TIRE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CHCCD /D/ 18TYPE,MATERIAL,INTERIOR COVERING INTERIOR COVERING MATERIAL TYPE INDICATES THE TYPE OF ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INTERIOR COVERING IS FABRICATED. SELECT REPLY CODE 10AN48 CHCDD /D/ 18TYPE,MATERIAL,EXTERIOR COVERING EXTERIOR COVERING MATERIAL TYPE INDICATES THE TYPE OF ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE EXTERIOR COVERING IS FABRICATED. SELECT REPLY CODE 10AN48 CHCFA /D/ 12QUANTITY,COMPARTMENT,BODY SECTIONAL BODY SECTIONAL COMPARTMENT QUANTITY THE NUMBER OF SECTIONAL COMPARTMENTS INCLUDED IN THE BODY. 1A MODE REPLY 0 CHCGD /D/ 07CHOCK,ADJUSTABLE,CARGO POSITIONING CARGO POSITIONING ADJUSTABLE CHOCK AN INDICATION OF WHETHER OR NOT A CARGO POSITIONING ADJUSTABLE CHOCK(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CHCHA /D/ 12QUANTITY,BEAM,LONGITUDINAL LONGITUDINAL BEAM QUANTITY THE NUMBER OF LONGITUDINAL BEAMS PROVIDED. 1A MODE REPLY 0 CHCJA /D/ 12QUANTITY,BEAM,ADJUSTABLE ADJUSTABLE BEAM QUANTITY THE NUMBER OF ADJUSTABLE BEAMS PROVIDED. 1A MODE REPLY 0 CHCKA /D/ 12QUANTITY,ROD,TIE TIE ROD QUANTITY THE NUMBER OF TIE RODS PROVIDED. 1A MODE REPLY 0 CHCLD /D/ 18TYPE,SECTION,CENTER,PLATFORM PLATFORM CENTER SECTION TYPE INDICATES THE TYPE OF PLATFORM CENTER SECTION PROVIDED. SELECT REPLY CODE 10AK54 CHCMD /D/ 08LOCATION,DEVICE,TIE-DOWN TIE-DOWN DEVICE LOCATION INDICATES THE LOCATION OF THE TIE-DOWN DEVICE(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 CHCND /D/ 07ADJUSTABILITY,DEVICE,WARHEAD HANDLING WARHEAD HANDLING DEVICE ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE WARHEAD HANDLING DEVICE IS ADJUSTABLE. SELECT REPLY CODE 10AB00 CHCPD /D/ 11METHOD,OPERATION,WARHEAD HANDLING DEVICE WARHEAD HANDLING DEVICE OPERATION METHOD THE MEANS BY WHICH THE WARHEAD HANDLING DEVICE IS OPERATED. SELECT REPLY CODE 10AC58 CHCQD /D/ 07COVER,HATCH HATCH COVER AN INDICATION OF WHETHER OR NOT A HATCH COVER(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CHCRD /D/ 07HOIST,TROLLEY TROLLEY HOIST AN INDICATION OF WHETHER OR NOT A TROLLEY HOIST(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CHCSA /D/ 12QUANTITY,RAIL,TROLLEY TROLLEY RAIL QUANTITY THE NUMBER OF TROLLEY RAILS PROVIDED. 1A MODE REPLY 0 CHCTJ /D/ 04DISTANCE BETWEEN RAILS DISTANCE BETWEEN RAILS THE DISTANCE BETWEEN THE RAILS. 2D AND 1B MODE REPLY21AA051AC20 CHCWJ /D/ 04HEIGHT ABOVE LOADING SURFACE,RAIL RAIL HEIGHT ABOVE LOADING SURFACE A MEASUREMENT FROM THE LOADING SURFACE TO THE TOP OF THE RAIL(S),IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CHCXJ /D/ 04LENGTH BEYOND TRAILER REAR END,RAIL RAIL LENGTH BEYOND TRAILER REAR END A MEASUREMENT OF THE EXTENDED LENGTH OF THE RAIL/S/ BEYOND THE TRAILER REAR END. 2D AND 1B MODE REPLY21AA051AC20 CHCYA /D/ 12QUANTITY,HOIST,TROLLEY TROLLEY HOIST QUANTITY THE NUMBER OF TROLLEY HOISTS PROVIDED. 1A MODE REPLY 0 CHCZJ /D/ 04DISTANCE,TRAVEL,MAXIMUM,TROLLEY HOIST TROLLEY HOIST MAXIMUM TRAVEL DISTANCE THE MAXIMUM DISTANCE THE TROLLEY HOIST IS CAPABLE OF TRAVELING. 1D AND 1B MODE REPLY11AA05 CHDBJ /D/ 10CAPACITY RATING,LOAD,TROLLEY HOIST TROLLEY HOIST LOAD CAPACITY RATING THE RATED LOAD CAPACITY THAT THE TROLLEY HOIST WILL ACCOMMODATE. 1D AND 1B MODE REPLY12AG67 CHDCA 12QUANTITY,DOOR,PASSENGER PASSENGER DOOR QUANTITY THE NUMBER OF PASSENGER DOORS PROVIDED. 1A MODE REPLY 0 CHDDD /D/ 08LOCATION,DOOR,PASSENGER PASSENGER DOOR LOCATION INDICATES THE LOCATION OF THE PASSENGER DOOR(S). SELECT REPLY CODE 10AJ91 CHDFD /D/ 11METHOD,ACTUATION,PASSENGER DOOR PASSENGER DOOR ACTUATION METHOD THE MEANS BY WHICH THE PASSENGER DOOR/S/ IS ACTUATED. SELECT REPLY CODE 10AC58 CHDGD /D/ 07DOOR,EMERGENCY EMERGENCY DOOR AN INDICATION OF WHETHER OR NOT AN EMERGENCY DOOR(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CHDJJ /D/ 04RADIUS,CLEARANCE,KINGPIN KINGPIN CLEARANCE RADIUS A MEASURMENT OF THE DISTANCE FROM THE KINGPIN CENTER TO THE CLEARANCE CURVE. 2D AND 1B MODE REPLY21AA051AC20 CHDKA 12QUANTITY,BOLSTER BOLSTER QUANTITY THE NUMBER OF BOLSTERS PROVIDED. 1A MODE REPLY 0 CHDLD 18TYPE,BOLSTER BOLSTER TYPE INDICATES THE TYPE OF BOLSTER PROVIDED. SELECT REPLY CODE 10AK54 CHDMA 12QUANTITY,STANCHION STANCHION QUANTITY THE NUMBER OF STANCHIONS PROVIDED. 1A MODE REPLY 0 CHDNG /D/ 03DESIGNATION,SIZE,SIEVE,USS TESTING USS TESTING SIEVE SIZE DESIGNATION AN INDICATION OF THE USS TESTING SIEVE SIZE. FULL TEXT WRITE-IN 0 CHDPB /D/ 10PERCENTAGE,BITUMEN BITUMEN PERCENTAGE THE AVERAGE NUMERIC PERCENTAGE OF BITUMEN IN THE ITEM. 1B MODE REPLY 0 CHDQJ /D/ 10TEMP,APPLICATION APPLICATION TEMP AN INDICATION OF THE REQUIRED TEMPERATURE OF THE ITEM FOR APPLICATION. 2D AND 1B MODE REPLY23AJ401AC20 CHDRG /D/ 10CONSISTENCY RATING AT SPECIFIED TEMP CONSISTENCY RATING AT SPECIFIED TEMP THE RATED CONSISTENCY OF THE ITEM GIVEN AT A SPECIFIED TEMPERATURE. FULL TEXT WRITE-IN 0 CHDSD /D/ 19NAME,EMULSIFIER EMULSIFIER NAME AN INDICATION OF THE NAME OF THE EMULSIFIER. SELECT REPLY CODE 10AH24 CHDTJ /D/ 10PERCENTAGE,EMULSIFIER EMULSIFIER PERCENTAGE THE PERCENTAGE OF EMULSIFIER IN THE ITEM. 1D AND 1B MODE REPLY11AC20 CHDWJ /D/T10RANGE,TEMP,SOFTENING POINT SOFTENING POINT TEMP RANGE AN INDICATION OF THE SOFTENING POINT TEMPERATURE RANGE. 1D AND 1F MODE REPLY13AJ40 CHDXG 10GRAVITY AT SPECIFIED TEMP,SPECIFIC SPECIFIC GRAVITY AT SPECIFIED TEMP THE NUMERIC VALUE WHICH INDICATES THE RATIO OF THE WEIGHT IN AIR OF A GIVEN VOLUME OF MATERIAL AT A SPECIFIED TEMPERATURE. FULL TEXT WRITE-IN 0 CHDYB /D/ 10PERCENTAGE UNDER 300 DEG CELSIUS,MAXIMUM,DISTILLATE DISTILLATE MAXIMUM PERCENTAGE UNDER 300 DEG CELSIUS THE MAXIMUM PERCENT OF DISTILLATE OBTAINED THROUGH DISTILLATION UNDER 300 DEGREES CELSIUS. 1B MODE REPLY 0 CHDZG /D/ 10GRAVITY AT SPECIFIED TEMP RANGE,SPECIFIC,MINIMUM,DISTILLATE DISTILLATE MINIMUM SPECIFIC GRAVITY AT SPECIFIED TEMP RANGE THE MINIMUM SPECIFIC GRAVITY OF THE DISTILLATE AT SPECIFIED TEMPERATURE RANGE. FULL TEXT WRITE-IN 0 CHFBD /D/ 11METHOD,TEST,ABRASION RESISTANCE ABRASION RESISTANCE TEST METHOD THE MEANS USED FOR TESTING THE ABRASION RESISTANCE. SELECT REPLY CODE 10AL43 CHFCG /D/ 10PERCENTAGE,LIMITATION,WEAR WEAR LIMITATION PERCENTAGE THE LIMIT OF PERCENTAGE OF WEAR. FULL TEXT WRITE-IN 0 CHFDD /D/ 11METHOD,TEST,SOUNDNESS SOUNDNESS TEST METHOD THE MEANS USED TO TEST THE SOUNDNESS OF THE ITEM. SELECT REPLY CODE 10AN48 CHFFA /D/ 12QUANTITY,CYCLE,TEST TEST CYCLE QUANTITY THE NUMBER OF TEST CYCLES PROVIDED. 1A MODE REPLY 0 CHFGB /D/ 10PERCENTAGE,LIMITATION,WEIGHTED LOSS WEIGHTED LOSS LIMITATION PERCENTAGE THE LIMIT OF PERCENTAGE OF WEIGHTED LOSS. 1B MODE REPLY 0 CHFHD /D/ 18TYPE FOR WHICH DESIGNED,SEAL,RUBBER RUBBER SEAL TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF RUBBER SEAL FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK39 CHFJG /D/ 10VISCOSITY AT RATED TEMP,MINIMUM,OIL CONSTITUENT OIL CONSTITUENT MINIMUM VISCOSITY AT RATED TEMP THE MINIMUM KINEMATIC UNITS (CENTISTOKES) OF THE OIL CONSTITUENT AT A SPECIFIED TEMPERATURE. FULL TEXT WRITE-IN 0 CHFKD /D/ 07FEATURE,APPLICATION,BRAKE BRAKE APPLICATION FEATURE AN INDICATION OF WHETHER OR NOT A BRAKE APPLICATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CHFLF /D/T10RANGE IN DEG FAHRENHEIT,TEMP,OPERATING,EFFECTIVE EFFECTIVE OPERATING TEMP RANGE IN DEG FAHRENHEIT THE EFFECTIVE OPERATING TEMPERATURE RANGE OF THE ITEM,EXPRESSED IN DEGREES FAHRENHEIT. 1F MODE REPLY 0 CHFMF /D/T10RANGE IN DEG FAHRENHEIT,DISTILLATION DISTILLATION RANGE IN DEG FAHRENHEIT THE DISTILLATION RANGE OF THE ITEM,EXPRESSED IN DEGREES FAHRENHEIT. 1F MODE REPLY 0 CHFND /D/ 07BASE,ESTER,PHOSPHATE PHOSPHATE ESTER BASE AN INDICATION OF WHETHER OR NOT A PHOSPHATE ESTER BASE IS PROVIDED. SELECT REPLY CODE 10AB22 CHFPB /D/ 10TEMP IN DEG FAHRENHEIT,FREEZING FREEZING TEMP IN DEG FAHRENHEIT THE TEMPERATURE AT WHICH THE ITEM WILL FREEZE,EXPRESSED IN DEGREES FAHRENHEIT. 1B MODE REPLY 0 CHFQG /D/ 10RANGE AT SPECIFIED TEMP,PENETRATION PENETRATION RANGE AT SPECIFIED TEMP THE RATED PENETRATION OF THE ITEM AT A SPECIFIED TEMPERATURE. FULL TEXT WRITE-IN 0 CHFRD 18TYPE,VEHICLE VEHICLE TYPE INDICATES THE TYPE OF VEHICLE PROVIDED. SELECT REPLY CODE 10AG63 CHFSD 07AGITATION AGITATION AN INDICATION OF THE NECESSITY OF AGITATING THE ITEM. SELECT REPLY CODE 10AE40 CHFTH /D/ 18TYPE AND LOCATION,MATERIAL MATERIAL TYPE AND LOCATION INDICATES THE TYPE OF MATERIAL USED AND ITS LOCATION. 2D MODE REPLY 24AN483AJ91 CHFWD /D/ 07GRAPHITE GRAPHITE AN INDICATION OF WHETHER OR NOT GRAPHITE IS INCLUDED. SELECT REPLY CODE 10AA49 CHFXB 10PERCENTAGE,GRAPHITE GRAPHITE PERCENTAGE THE PERCENTAGE OF GRAPHITE IN THE ITEM. 1B MODE REPLY 0 CHFYG /D/ 10PENETRATION AT SPECIFIED TEMP,WORKED WORKED PENETRATION AT SPECIFIED TEMP THE WORKED PENETRATION OF THE ITEM AT A SPECIFIED TEMPERATURE. FULL TEXT WRITE-IN 0 CHFZG 10PENETRATION AT SPECIFIED TEMP,UNWORKED UNWORKED PENETRATION AT SPECIFIED TEMP THE UNWORKED PENETRATION OF THE ITEM AT A SPECIFIED TEMPERATURE. FULL TEXT WRITE-IN 0 CHGBB /D/ 10POINT IN DEG FAHRENHEIT,DROPPING,MINIMUM MINIMUM DROPPING POINT IN DEG FAHRENHEIT THE NUMERIC VALUE OF THE MINIMUM DROPPING POINT,EXPRESSED IN DEGREES FAHRENHEIT. 1B MODE REPLY 0 CHGCB /D/ 10POINT IN DEG FAHRENHEIT,MELTING,MINIMUM MINIMUM MELTING POINT IN DEG FAHRENHEIT THE NUMERIC VALUE OF THE MINIMUM MELTING POINT,EXPRESSED IN DEGREES FAHRENHEIT. 1B MODE REPLY 0 CHGDB /D/ 10PRESSURE IN DEG FAHRENHEIT,VAPOR,MAXIMUM MAXIMUM VAPOR PRESSURE IN DEG FAHRENHEIT THE MAXIMUM VAPOR PRESSURE FOR WHICH THE ITEM IS RATED,EXPRESSED IN DEGREES FAHRENHEIT. 1B MODE REPLY 0 CHGFB /D/ 10INDEX,WEAR,MINIMUM PRESSURE MINIMUM PRESSURE WEAR INDEX THE NUMERIC VALUE OF THE MINIMUM PRESSURE WEAR INDEX OF THE ITEM. 1B MODE REPLY 0 CHGGG /D/ 10VISCOSITY AT RATED TEMP,MINERAL OIL MINERAL OIL VISCOSITY AT RATED TEMP THE KINEMATIC UNITS (CENTISTOKES) OF THE ITEM AT A SPECIFIED TEMPERATURE. FULL TEXT WRITE-IN 0 CHGHD /D/ 07FEATURE,FORM,STICK STICK FORM FEATURE AN INDICATION OF WHETHER OR NOT A STICK FORM FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CHGJD 18TYPE,POINT,CURVED CURVED POINT TYPE INDICATES THE TYPE OF CURVED POINT(S) PROVIDED. SELECT REPLY CODE 10AJ44 CHGKD 18TYPE,POINT,STRAIGHT STRAIGHT POINT TYPE INDICATES THE TYPE OF STRAIGHT POINT(S) PROVIDED. SELECT REPLY CODE 10AJ44 CHGLD 18TYPE,GREASE GREASE TYPE INDICATES THE TYPE OF GREASE PROVIDED. SELECT REPLY CODE 10AM39 CHGMD 18TYPE,INTAKE,EMERGENCY AIR EMERGENCY AIR INTAKE TYPE INDICATES THE TYPE OF EMERGENCY AIR INTAKE PROVIDED. SELECT REPLY CODE 10AC57 CHGNG /D/ 12QUANTITY AND MAXIMUM OPERATING PRESSURE,SUBCIRCUIT SUBCIRCUIT QUANTITY AND MAXIMUM OPERATING PRESSURE THE NUMBER OF SUBCIRCUITS PROVIDED AND THE MAXIMUM OPERATING PRESSURE OF EACH SUBCIRCUIT. FULL TEXT WRITE-IN 0 CHGPJ 10PRESSURE RATING,CIRCUIT CIRCUIT PRESSURE RATING THE PRESSURE AT WHICH THE CIRCUIT IS RATED. 2D AND 1B MODE REPLY22AG671AC20 CHGQD /D/ 07SYSTEM,FILTERING FILTERING SYSTEM AN INDICATION OF WHETHER OR NOT A FILTERING SYSTEM IS INCLUDED. SELECT REPLY CODE 10AA49 CHGRD /D/ 07HOSE,PRESSURE/SUCTION PRESSURE/SUCTION HOSE AN INDICATION OF WHETHER OR NOT A PRESSURE AND SUCTION HOSE ARE INCLUDED. SELECT REPLY CODE 10AA49 CHGSF T10RANGE IN RPM,TEST,LOW SPEED LOW SPEED TEST RANGE IN RPM THE MINIMUM TO MAXIMUM LIMITS AT WHICH EXAMINATION OF AN ITEM IS PERFORMED AT LOW SPEED,EXPRESSED IN REVOLUTIONS PER MINUTE. 1F MODE REPLY 0 CHGTF T10RANGE IN RPM,TEST,HIGH SPEED HIGH SPEED TEST RANGE IN RPM THE MINIMUM TO MAXIMUM LIMITS AT WHICH EXAMINATION OF AN ITEM IS PERFORMED AT HIGH SPEED,EXPRESSED IN REVOLUTIONS PER MINUTE. 1F MODE REPLY 0 CHGWF T10RANGE IN RPM,TEST,SPEED SPEED TEST RANGE IN RPM THE MINIMUM TO MAXIMUM LIMITS AT WHICH EXAMINATION OF AN ITEM IS PERFORMED,EXPRESSED IN REVOLUTIONS PER MINUTE. 1F MODE REPLY 0 CHGXJ 04DIAMETER ACCOMMODATED,GENERATOR,MAXIMUM MAXIMUM GENERATOR DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MAXIMUM GENERATOR THE ITEM IS DESIGNED TO ACCOMMODATE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CHGYJ T10RANGE IN VOLTS AND CURRENT TYPE ACCOMMODATED,VOLTAGE,GENERATOR GENERATOR VOLTAGE RANGE IN VOLTS AND CURRENT TYPE ACCOMMODATED AN INDICATION OF THE GENERATOR VOLTAGE RANGE AND CURRENT TYPE THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1F MODE REPLY11AB62 CHGZB 10OUTPUT IN AMPS ACCOMMODATED,GENERATOR,MAXIMUM MAXIMUM GENERATOR OUTPUT IN AMPS ACCOMMODATED THE MAXIMUM GENERATOR OUTPUT CURRENT THE ITEM IS DESIGNED TO ACCOMMODATE,EXPRESSED IN AMPERES. 1B MODE REPLY 0 CHHBD /D/ 07TRANSMISSION,MOTOR,DRIVING DRIVING MOTOR TRANSMISSION AN INDICATION OF WHETHER OR NOT A DRIVING MOTOR TRANSMISSION IS INCLUDED. SELECT REPLY CODE 10AA49 CHHCA 12QUANTITY,SPEED SPEED QUANTITY THE NUMBER OF SPEEDS PROVIDED. 1A MODE REPLY 0 CHHDD /D/ 07BLOWER,MOTOR,ELECTRIC ELECTRIC MOTOR BLOWER AN INDICATION OF WHETHER OR NOT AN ELECTRIC MOTOR BLOWER IS INCLUDED. SELECT REPLY CODE 10AA49 CHHFJ 10VOLTAGE IN VOLTS,MOTOR,BLOWER BLOWER MOTOR VOLTAGE IN VOLTS THE VALUE,OR RANGE OF VALUES,OF POTENTIAL FOR WHICH THE BLOWER MOTOR IS RATED,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AC20 CHHGD /D/ 07FILTER,PARTICULATE PARTICULATE FILTER AN INDICATION OF WHETHER OR NOT A PARTICULATE FILTER IS INCLUDED. SELECT REPLY CODE 10AA49 CHHHD 10PHASE,MOTOR,BLOWER BLOWER MOTOR PHASE THE NUMBER OF BLOWER MOTOR ALTERNATING CURRENT PHASES. SELECT REPLY CODE 10AD02 CHHJJ 10FREQUENCY IN HERTZ,MOTOR,BLOWER BLOWER MOTOR FREQUENCY IN HERTZ THE CYCLES PER SECOND (HERTZ) OF THE BLOWER MOTOR ALTERNATING CURRENT. 1D AND 1B MODE REPLY11AC20 CHHKB 10TILT FROM HORIZONTAL POSITION IN DEG,MAXIMUM MAXIMUM TILT FROM HORIZONTAL POSITION IN DEG AN INDICATION OF THE MAXIMUM TILT OF THE TABLE PLANE FROM THE HORIZONTAL POSITION OF THE ITEM,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CHHLD /D/ 07DEVICE,LEVELING,TABLE TOP TABLE TOP LEVELING DEVICE AN INDICATION OF WHETHER OR NOT A TABLE TOP LEVELING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 CHHMD /D/ 07SCALE,TILTING,VERNIER VERNIER TILTING SCALE AN INDICATION OF WHETHER OR NOT A VERNIER TILTING SCALE IS INCLUDED. SELECT REPLY CODE 10AA49 CHHND /D/ 07SCALE,ANGULAR,VERNIER VERNIER ANGULAR SCALE AN INDICATION OF WHETHER OR NOT A VERNIER ANGULAR SCALE IS INCLUDED. SELECT REPLY CODE 10AA49 CHHPD /D/ 07OUTRIGGERS OUTRIGGERS AN INDICATION OF WHETHER OR NOT OUTRIGGERS ARE INCLUDED. SELECT REPLY CODE 10AA49 CHHQJ /D/ 10CAPACITY W/OUTRIGGERS,LOAD,RATED RATED LOAD CAPACITY W/OUTRIGGERS A MEASUREMENT OF THE RATED LOAD THE ITEM IS DESIGNED TO ACCOMMODATE WHEN EQUIPPED WITH OUTRIGGERS. 1D AND 1B MODE REPLY12AG67 CHHRJ /D/ 10CAPACITY W/O OUTRIGGERS,LOAD,RATED RATED LOAD CAPACITY W/O OUTRIGGERS A MEASUREMENT OF THE RATED LOAD CAPACITY THE ITEM IS DESIGNED TO ACCOMMODATE WHEN NOT EQUIPPED WITH OUTRIGGERS. 1D AND 1B MODE REPLY12AG67 CHHSJ 04HEIGHT,RAIL,GUARD,PLATFORM PLATFORM GUARD RAIL HEIGHT A MEASUREMENT FROM THE PLATFORM TO THE TOP OF THE GUARD RAIL,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CHHTD /D/ 07INSULATION,PLATFORM PLATFORM INSULATION AN INDICATION OF WHETHER OR NOT PLATFORM INSULATION IS INCLUDED. SELECT REPLY CODE 10AA49 CHHWB 10VOLTAGE RATING IN VOLTS,PROTECTION,SAFE SAFE PROTECTION VOLTAGE RATING IN VOLTS THE TOTAL ELECTRICAL VOLTAGE AT WHICH THE ITEM IS RATED FOR SAFE PROTECTION,EXPRESSED IN VOLTS. 1B MODE REPLY 0 CHHXJ 04HEIGHT WITH BOOM EXTENDED,MAXIMUM,PLATFORM PLATFORM MAXIMUM HEIGHT WITH BOOM EXTENDED THE MAXIMUM MEASUREMENT FROM GROUND LEVEL TO THE UPPERMOST PORTION OF THE PLATFORM WITH THE BOOM EXTENDED. 1D AND 1B MODE REPLY11AA05 CHHYJ 04THREAD DIAMETER FOR WHICH DESIGNED,SHAFT SHAFT THREAD DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A THREADED SHAFT FOR WHICH DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CHHZJ 10REACH,HORIZONTAL,MAXIMUM,PLATFORM PLATFORM MAXIMUM HORIZONTAL REACH A MEASUREMENT OF THE MAXIMUM HORIZONTAL DISTANCE THE PLATFORM CAN REACH. 1D AND 1B MODE REPLY11AA05 CHJBB /D/ 10ROTATION IN DEG,BOOM,MAXIMUM MAXIMUM BOOM ROTATION IN DEG A MEASUREMENT OF THE MAXIMUM ROTATION OF THE BOOM,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CHJCD /D/ 07FEATURE,DESIGN,BELOW SURFACE LEVEL REACH BELOW SURFACE LEVEL REACH DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A DESIGN FEATURE FOR REACHING BELOW SURFACE LEVEL IS INCLUDED. SELECT REPLY CODE 10AA49 CHJDD 08LOCATION,CONTROL,OPERATING OPERATING CONTROL LOCATION INDICATES THE LOCATION OF THE OPERATING CONTROL(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 CHJFG 19NAME,MANUFACTURER,VEHICLE VEHICLE MANUFACTURER NAME THE NAME OF THE MANUFACTURER OF THE VEHICLE. FULL TEXT WRITE-IN 0 CHJGG /D/ 19NUMBER,IDENTIFYING,VEHICLE VEHICLE IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE VEHICLE. FULL TEXT WRITE-IN 0 CHJHG /D/ 04DIMENSION,LEVEL,WORKING WORKING LEVEL DIMENSION A MEASUREMENT OF THE HEIGHT,HEIGHT RANGE,OR DEPTH AT WHICH THE WORK IS PERFORMED. FULL TEXT WRITE-IN 0 CHJJA 12QUANTITY,PLATFORM,WORKING WORKING PLATFORM QUANTITY THE NUMBER OF WORKING PLATFORMS PROVIDED. 1A MODE REPLY 0 CHJKD 18TYPE,SHELTER SHELTER TYPE INDICATES THE TYPE OF SHELTER PROVIDED. SELECT REPLY CODE 10AK54 CHJLD /D/ 07LADDER LADDER AN INDICATION OF WHETHER OR NOT A LADDER(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CHJMD /D/ 07GUARD,SAFETY,PLATFORM PLATFORM SAFETY GUARD AN INDICATION OF WHETHER OR NOT A PLATFORM SAFETY GUARD(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CHJND 18TYPE,STANCHION STANCHION TYPE INDICATES THE TYPE OF STANCHION(S) PROVIDED. SELECT REPLY CODE 10AK54 CHJPD /D/ 07ACCOMMODATION,REEL REEL ACCOMMODATION AN INDICATION OF WHETHER OR NOT A REEL ACCOMMODATION/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CHJQD 18TYPE,SUPPORT,REEL REEL SUPPORT TYPE INDICATES THE TYPE OF REEL SUPPORT PROVIDED. SELECT REPLY CODE 10AK54 CHJRJ 04DIAMETER,OUTSIDE,LARGEST ACCOMMODATED REEL LARGEST ACCOMMODATED REEL OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST REEL THE ITEM IS DESIGNED TO ACCOMMODATE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CHJSD /D/ 19POSITION FOR WHICH DESIGNED,MOUNTING,REEL REEL MOUNTING POSITION FOR WHICH DESIGNED AN INDICATION OF THE MOUNTING POSITION OF THE REEL FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AC60 CHJWA 12QUANTITY,ACCOMMODATION,SLEEPING SLEEPING ACCOMMODATION QUANTITY THE NUMBER OF SLEEPING ACCOMMODATIONS PROVIDED. 1A MODE REPLY 0 CHJXD 18TYPE,FACILITY,BATH BATH FACILITY TYPE INDICATES THE TYPE OF FACILITY(IES) PROVIDED FOR BATHING. SELECT REPLY CODE 10AK54 CHJYD /D/ 07SHELL,CYLINDER,OUTER OUTER CYLINDER SHELL AN INDICATION OF WHETHER OR NOT AN OUTER CYLINDER SHELL IS INCLUDED. SELECT REPLY CODE 10AA49 CHJZA 12QUANTITY,CYLINDER,GAS GAS CYLINDER QUANTITY THE NUMBER OF GAS CYLINDERS PROVIDED. 1A MODE REPLY 0 CHKBJ 10CAPACITY RATING,CYLINDER CYLINDER CAPACITY RATING A MEASUREMENT OF THE RATED CAPACITY OF THE CYLINDER. 1D AND 1B MODE REPLY12AG67 CHKCD 19POSITION,MOUNTING,CYLINDER CYLINDER MOUNTING POSITION THE INSTALLED POSITION OF THE CYLINDER. SELECT REPLY CODE 10AM84 CHKDD /D/ 07PUMP,TRANSFER TRANSFER PUMP AN INDICATION OF WHETHER OR NOT A TRANSFER PUMP(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CHKFD /D/ 07PUMP,VACUUM VACUUM PUMP AN INDICATION OF WHETHER OR NOT A VACUUM PUMP(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CHKGD /D/ 07TAILGATE,HINGED HINGED TAILGATE AN INDICATION OF WHETHER OR NOT A HINGED TAILGATE IS INCLUDED. SELECT REPLY CODE 10AA49 CHKHD 08LOCATION,ACCESS,STORAGE FACILITY STORAGE FACILITY ACCESS LOCATION INDICATES THE ACCESS LOCATION(S) OF THE STORAGE FACILITY(IES). SELECT REPLY CODE 10AJ91 CHKJD /D/ 07SIDE,FOLD-DOWN FOLD-DOWN SIDE AN INDICATION OF WHETHER OR NOT A FOLD-DOWN SIDE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CHKKJ 04LENGTH ACCOMMODATED,BODY BODY LENGTH ACCOMMODATED A MEASUREMENT OF THE LONGEST DIMENSION OF THE BODY THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CHKLJ 04WIDTH ACCOMMODATED,BODY BODY WIDTH ACCOMMODATED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BODY THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CHKMJ 04DISTANCE FROM FLOOR TO FRAME TOP DISTANCE FROM FLOOR TO FRAME TOP THE DISTANCE FROM THE FLOOR TO THE TOP OF THE FRAME. 2D AND 1B MODE REPLY21AA051AC20 CHKND 18TYPE,PLATE,COUPLER COUPLER PLATE TYPE INDICATES THE TYPE OF COUPLER PLATE PROVIDED. SELECT REPLY CODE 10AK54 CHKPD 03DESIGNATION FOR WHICH DESIGNED,SIZE,KINGPIN KINGPIN SIZE DESIGNATION FOR WHICH DESIGNED THE SIZE DESIGNATION OF THE KINGPIN FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AE25 CHKQD 03DESIGNATION,SIZE,PLATE KINGPIN PLATE KINGPIN SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE PLATE KINGPIN IS COMMERCIALLY KNOWN. SELECT REPLY CODE 10AE25 CHKRJ 04WIDTH ACCOMMODATED,REEL REEL WIDTH ACCOMMODATED THE WIDTH OF THE REEL THE ITEM IS DESIGNED TO ACCOMMODATE. 2D AND 1B MODE REPLY21AA051AC20 CHKSD /D/ 19POSITION,MOUNTING,REEL AXLE REEL AXLE MOUNTING POSITION AN INDICATION OF THE MOUNTING POSITION OF THE REEL AXLE/S/. SELECT REPLY CODE 10AC60 CHKTA 12QUANTITY,AXLE,REEL REEL AXLE QUANTITY THE NUMBER OF REEL AXLES PROVIDED. 1A MODE REPLY 0 CHKWD /D/ 07PROVISION,DRAWING,HAND HAND DRAWING PROVISION AN INDICATION OF WHETHER OR NOT A PROVISION/S/ FOR DRAWING BY HAND IS INCLUDED. SELECT REPLY CODE 10AA49 CHKXD /D/ 07DEVICE,LIFTING,INTEGRAL INTEGRAL LIFTING DEVICE AN INDICATION OF WHETHER OR NOT AN INTEGRAL LIFTING DEVICE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CHKYD 19CONSTRUCTION,FRAME FRAME CONSTRUCTION THE STRUCTURAL CHARACTERISTIC(S) OF THE FRAME. SELECT REPLY CODE 10AL59 CHKZJ 04LENGTH,WHEELBASE WHEELBASE LENGTH A MEASUREMENT OF THE LONGEST CENTER TO CENTER DIMENSION BETWEEN THE FRONT AND REAR WHEELS. 2D AND 1B MODE REPLY21AA051AC20 CHLBJ 04HEIGHT,RETRACTED,OVERALL,CRADLE CRADLE OVERALL RETRACTED HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE CRADLE IN ITS RETRACTED POSITION. 2D AND 1B MODE REPLY21AA051AC20 CHLCJ 04HEIGHT,EXTENDED,OVERALL,CRADLE CRADLE OVERALL EXTENDED HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE CRADLE IN ITS EXTENDED POSITION. 2D AND 1B MODE REPLY21AA051AC20 CHLDJ 10UNDERCLEARANCE,OVERALL OVERALL UNDERCLEARANCE AN OVERALL MEASUREMENT OF THE DISTANCE BETWEEN THE GROUND SURFACE AND THE BOTTOM OF AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 CHLFD 18TYPE,SEAT,OPERATOR OPERATOR SEAT TYPE INDICATES THE TYPE OF SEAT PROVIDED FOR THE OPERATOR. SELECT REPLY CODE 10AK54 CHLGD 11METHOD,STEERING STEERING METHOD THE MEANS USED TO STEER THE ITEM. SELECT REPLY CODE 10AC58 CHLHD /D/ 07TURRET TURRET AN INDICATION OF WHETHER OR NOT A TURRET(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CHLJB 10TRAVERSE IN DEG TRAVERSE IN DEG AN INDICATION OF THE DEGREE OF TRAVERSE. 1B MODE REPLY 0 CHLKD 02DESIGN,TURRET TURRET DESIGN THE DESIGN OF THE TURRET. SELECT REPLY CODE 10AK54 CHLLD /D/ 07SPADE,ANCHOR ANCHOR SPADE AN INDICATION OF WHETHER OR NOT AN ANCHOR SPADE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CHLMJ 10WEIGHT,FIGHTING FIGHTING WEIGHT THE TOTAL WEIGHT OF THE ITEM WHEN COMBAT LOADED. 1D AND 1B MODE REPLY12AG67 CHLND 19CHARACTERISTIC,EQUALIZATION EQUALIZATION CHARACTERISTIC AN INDICATION OF THE EQUALIZATION CHARACTERISTIC(S) OF THE ITEM. SELECT REPLY CODE 10AK54 CHLPA 12QUANTITY,SLEEVE SLEEVE QUANTITY THE NUMBER OF SLEEVES PROVIDED. 1A MODE REPLY 0 CHLQD /D/ 17SURFACE TREATMENT,SLEEVE SLEEVE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SLEEVE SURFACE. PLEASE USE MRC SFTT WITH USE OF ISAC TBL 0094 IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 CHLRD /D/ 17SURFACE TREATMENT,FLANGE FLANGE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE FLANGE SURFACE. PLEASE USE MRC SFTT WITH USE OF ISAC TBL 0094 IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 CHLSD /D/ 11METHOD,OPERATION,DEAD BOLT DEAD BOLT OPERATION METHOD THE MEANS USED TO OPERATE THE DEAD BOLT. SELECT REPLY CODE 10AC58 CHLTJ 04LENGTH,MAXIMUM,TRAVERSE TRAVERSE MAXIMUM LENGTH THE MEASUREMENT OF THE MAXIMUM TRAVERSE LENGTH OF THE ITEM. 1D AND 1B MODE REPLY11AA05 CHLWD 18TYPE,SHOULDER SHOULDER TYPE INDICATES THE TYPE OF SHOULDER(S) PROVIDED. SELECT REPLY CODE 10AB47 CHLXD /D/ 11METHOD,OPERATION,LATCH BOLT LATCH BOLT OPERATION METHOD THE MEANS USED TO OPERATE THE LATCH BOLT. SELECT REPLY CODE 10AC58 CHLYJ /D/T04THICKNESS RANGE FOR WHICH DESIGNED,DOOR DOOR THICKNESS RANGE FOR WHICH DESIGNED THE MINIMUM AND MAXIMUM THICKNESS OF THE DOOR FOR WHICH THE ITEM IS DESIGNED. 1D AND 1F MODE REPLY11AA05 CHLZD 18TYPE,MECHANISM,LOCKING LOCKING MECHANISM TYPE INDICATES THE TYPE OF LOCKING MECHANISM PROVIDED. SELECT REPLY CODE 10AE36 CHMBJ /D/ 04THICKNESS FOR WHICH DESIGNED,MINIMUM,DOOR DOOR MINIMUM THICKNESS FOR WHICH DESIGNED THE MINIMUM THICKNESS OF THE DOOR FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AA05 CHMCJ 04THICKNESS FOR WHICH DESIGNED,MINIMUM,MEMBER MEMBER MINIMUM THICKNESS FOR WHICH DESIGNED THE MINIMUM THICKNESS OF THE MEMBER FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AA05 CHMDD /D/ 17SURFACE TREATMENT,KNOB KNOB SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE KNOB SURFACE. SELECT REPLY CODE 10AD09 CHMFD 14SHAPE,KNOB KNOB SHAPE THE PHYSICAL CONFIGURATION OF THE KNOB. SELECT REPLY CODE 10AD07 CHMGD /D/ 02DESIGN,KNOB KNOB DESIGN THE DESIGN OF THE KNOB. SELECT REPLY CODE 10AK54 CHMHA 12QUANTITY,PULL,DOOR DOOR PULL QUANTITY THE NUMBER OF DOOR PULLS PROVIDED. 1A MODE REPLY 0 CHMJD /D/ 09MATERIAL,PULL,DOOR DOOR PULL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE DOOR PULL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CHMKD /D/ 17SURFACE TREATMENT,PULL,DOOR DOOR PULL SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A DOOR PULL SURFACE. SELECT REPLY CODE 10AD09 CHMLD 18TYPE,PULL,DOOR DOOR PULL TYPE INDICATES THE TYPE OF DOOR PULL FURNISHED. SELECT REPLY CODE 10AC55 CHMMD /D/ 07KEYWAY,PULL,DOOR DOOR PULL KEYWAY AN INDICATION OF WHETHER OR NOT A DOOR PULL KEYWAY IS PROVIDED. SELECT REPLY CODE 10AB22 CHMND /D/ 07BAR,RELEASE RELEASE BAR AN INDICATION OF WHETHER OR NOT A RELEASE BAR IS INCLUDED. SELECT REPLY CODE 10AA49 CHMPD /D/ 09MATERIAL,BAR BAR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH A BAR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CHMQJ /D/ 04DIAMETER,MAJOR,BAR BAR MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BAR,AND TERMINATES AT THE OUTERMOST CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CHMRJ /D/ 04DIAMETER,MINOR,BAR BAR MINOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BAR,AND TERMINATES AT THE INNERMOST CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CHMSJ /D/ 04HEIGHT,CASE,ACTIVE ACTIVE CASE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN ACTIVE CASE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CHMTJ /D/ 04WIDTH,CASE,ACTIVE ACTIVE CASE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ACTIVE CASE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CHMWJ /D/ 04HEIGHT,PLATE,ACTIVE ESCUTCHEON ACTIVE ESCUTCHEON PLATE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A ACTIVE ESCUTCHEON PLATE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CHMXJ /D/ 04WIDTH,PLATE,ACTIVE ESCUTCHEON ACTIVE ESCUTCHEON PLATE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ACTIVE ESCUTCHEON PLATE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CHMYJ /D/ 04HEIGHT,CASE,SUPPORTING SUPPORTING CASE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A SUPPORTING CASE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CHMZJ /D/ 04WIDTH,CASE,SUPPORTING SUPPORTING CASE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SUPPORTING CASE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CHNBJ /D/ 04HEIGHT,PLATE,SUPPORTING ESCUTCHEON SUPPORTING ESCUTCHEON PLATE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A SUPPORTING ESCUTCHEON PLATE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CHNCJ /D/ 04WIDTH,PLATE,SUPPORTING ESCUTCHEON SUPPORTING ESCUTCHEON PLATE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A SUPPORTING ESCUTCHEON PLATE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CHNDD /D/ 07DEVICE,HOLDING,DEPRESSED POSITION BAR DEPRESSED POSITION BAR HOLDING DEVICE AN INDICATION OF WHETHER OR NOT A DEPRESSED POSITION BAR HOLDING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 CHNFJ /D/ 04HEIGHT,CASE CASE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE CASE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CHNGJ /D/ 04THICKNESS,CASE CASE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A CASE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CHNHJ /D/ 04SPACING DIMENSION SPACING DIMENSION THE SPACING BETWEEN TWO SPECIFIED POINTS ON AN ITEM. 2D AND 1B MODE REPLY21AA053AJ91 CHNJJ /D/ 04SPACING DIMENSION,OUTSIDE OUTSIDE SPACING DIMENSION THE SPACING BETWEEN TWO SPECIFIED OUTSIDE POINTS ON AN ITEM. 2D AND 1B MODE REPLY21AA053AJ91 CHNKJ /D/ 04SPACING DIMENSION,INSIDE INSIDE SPACING DIMENSION THE SPACING BETWEEN TWO SPECIFIED INSIDE POINTS ON AN ITEM. 2D AND 1B MODE REPLY21AA053AJ91 CHNLJ 04DEPTH,BACKSET BACKSET DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE BACKSET,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CHNMD /D/ 17SURFACE TREATMENT,FACE FACE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A FACE SURFACE. SELECT REPLY CODE 10AD09 CHNND 01COLOR,WALLET WALLET COLOR THE HUE OR TINT OF THE WALLET. SELECT REPLY CODE 10AD06 CHNPJ /D/T04SIZE,WALLET,OPEN OPEN WALLET SIZE DESIGNATES THE SIZE OF THE WALLET IN AN OPEN POSITION. 1D AND 1F MODE REPLY11AA05 CHNQJ /D/T04SIZE,WALLET,CLOSED CLOSED WALLET SIZE DESIGNATES THE SIZE OF THE WALLET IN A CLOSED POSITION. 1D AND 1F MODE REPLY11AA05 CHNRD /D/ 07INDEX,TELEPHONE TELEPHONE INDEX AN INDICATION OF WHETHER OR NOT A TELEPHONE INDEX IS INCLUDED. SELECT REPLY CODE 10AA49 CHNSD /D/ 07SPACE FOR MEMORANDA,BLANK BLANK SPACE FOR MEMORANDA AN INDICATION OF WHETHER OR NOT A BLANK SPACE FOR MEMORANDA IS INCLUDED. SELECT REPLY CODE 10AA49 CHNTG 19MARKING,TAB TAB MARKING AN INDICATION OF THE MARKING(S) ON THE TAB. FULL TEXT WRITE-IN 0 CHNWJ 04LENGTH,SQUARE,HEAD HEAD SQUARE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SQUARE PORTION OF THE HEAD,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CHNXD /D/ 07ROD,TURNING,HAND HAND TURNING ROD AN INDICATION OF WHETHER OR NOT A HAND TURNING ROD IS INCLUDED. SELECT REPLY CODE 10AA49 CHNYG /D/ 19LEGEND K LEGEND K NONE. FULL TEXT WRITE-IN 0 CHNZA /D/ 16STYLE,ROLLER ROLLER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ROLLER. 1A MODE REPLY 0 CHPBD 14SHAPE FOR WHICH SPLIT DIE IS DESIGNED,STEEL,DRILL DRILL STEEL SHAPE FOR WHICH SPLIT DIE IS DESIGNED THE PHYSICAL CONFIGURATION OF THE DRILL STEEL FOR WHICH THE SPLIT DIE IS DESIGNED. SELECT REPLY CODE 10AD07 CHPCJ 04WIDTH ACROSS FLATS,STEEL,DRILL DRILL STEEL WIDTH ACROSS FLATS A MEASUREMENT OF THE DRILL STEEL DISTANCE FROM ONE FLAT TO THE OPPOSITE FLAT,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CHPDJ /D/ 04DIAMETER,STEEL,DRILL DRILL STEEL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CIRCULAR DRILL STEEL,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CHPFD 14SHAPE FOR WHICH MOVABLE DIE IS DESIGNED,STEEL,DRILL DRILL STEEL SHAPE FOR WHICH MOVABLE DIE IS DESIGNED THE PHYSICAL CONFIGURATION OF THE DRILL STEEL FOR WHICH THE MOVABLE DIE IS DESIGNED. SELECT REPLY CODE 10AD07 CHPGJ 04WIDTH ACROSS FLATS,SHANK,STEEL,DRILL DRILL STEEL SHANK WIDTH ACROSS FLATS A MEASUREMENT OF THE DRILL STEEL SHANK DISTANCE FROM ONE FLAT TO THE OPPOSITE FLAT,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CHPHJ /D/ 04DIAMETER,SHANK,STEEL,DRILL DRILL STEEL SHANK DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR DRILL STEEL SHANK,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CHPJJ 04LENGTH ACCOMMODATED,END,DRILL STEEL SHANK,MOVABLE DIE MOVABLE DIE DRILL STEEL SHANK END LENGTH ACCOMMODATED A MEASUREMENT OF THE LONGEST DEMENSION OF A DRILL STEEL SHANK END ACCOMMODATED BY THE MOVABLE DIE. 2D AND 1B MODE REPLY21AA051AC20 CHPKJ 04LENGTH,SHANK,SQUARE SQUARE SHANK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SQUARE SHANK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CHPLJ 04DIAMETER,HOLE,GUIDE GUIDE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CHPMJ 04DIAMETER,END,MACHINE MACHINE END DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CHPNJ /D/ 04DISTANCE TO FLAT,CENTER,HOLE HOLE CENTER DISTANCE TO FLAT NONE. 2D AND 1B MODE REPLY21AA051AC20 CHPPJ 04DIAMETER,PUNCHING PUNCHING DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CHPQA 19NUMBER,SIZE,MORSE TAPER DRIVE MORSE TAPER DRIVE SIZE NUMBER AN INDICATION OF THE MORSE TAPER DRIVE SIZE NUMBER. 1A MODE REPLY 0 CHPRJ 04DIAMETER FOR WHICH DESIGNED,INSIDE,TUBE TUBE INSIDE DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBE FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CHPSJ /D/ 04THICKNESS,SHEET,TUBE TUBE SHEET THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE TUBE SHEET,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CHPTD 07ADJUSTABILITY,CAGE CAGE ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE CAGE IS ADJUSTABLE. SELECT REPLY CODE 10AB00 CHPWJ A18TYPE AND QUANTITY,ROLL ROLL TYPE AND QUANTITY INDICATES THE TYPE OF ROLL(S) AND THE NUMBER PROVIDED. 1D AND 1A MODE REPLY13AM21 CHPXG 04SIZE,HANDHOLE,ENTERING ENTERING HANDHOLE SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE ENTERING HANDHOLE. FULL TEXT WRITE-IN 0 CHPYD /D/ 07MOUNTING MOUNTING AN INDICATION OF WHETHER OR NOT A MOUNTING/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CHPZG 12QUANTITY AND SIZE,DIE,PIPE PIPE DIE QUANTITY AND SIZE AN INDICATION OF THE NUMBER AND SIZE(S) OF THE PIPE DIE(S) INCLUDED. FULL TEXT WRITE-IN 0 CHQBB /D/ 10PERCENTAGE,TRIOXIDE,SULFUR SULFUR TRIOXIDE PERCENTAGE A MEASUREMENT OF THE AMOUNT OF SULFUR TRIOXIDE CONTAINED IN THE ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 CHQCB /D/ 10PERCENTAGE,ACIDS,FATTY,FREE/COMBINED FREE/COMBINED FATTY ACIDS PERCENTAGE A MEASUREMENT OF THE AMOUNT OF FREE AND COMBINED FATTY ACIDS CONTAINED IN THE ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 CHQDB /D/ 10POINT IN DEG FAHRENHEIT,SOLIDIFICATION SOLIDIFICATION POINT IN DEG FAHRENHEIT THE TEMPERATURE AT WHICH THE ITEM WILL BECOME SOLID OR HARD,EXPRESSED IN DEGREES FAHRENHEIT. 1B MODE REPLY 0 CHQFD /D/ 07FEATURE,RESISTANT,MILDEW MILDEW RESISTANT FEATURE AN INDICATION OF WHETHER OR NOT A MILDEW RESISTANT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CHQGB 10NUMBER,NEUTRALIZATION,MAXIMUM MAXIMUM NEUTRALIZATION NUMBER AN INDICATION OF THE HIGHEST NEUTRALIZATION NUMBER OF THE ITEM. 1B MODE REPLY 0 CHQHJ /D/T10RANGE,TEMP,WAX MELTING POINT WAX MELTING POINT TEMP RANGE THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH THE WAX WILL MELT. 1D AND 1F MODE REPLY13AJ40 CHQJF /D/T10PERCENTAGE,VOLUME,TEMP RANGE TEMP RANGE VOLUME PERCENTAGE A MEASUREMENT OF THE PERCENT OF THE ITEM,BY VOLUME,THAT FALLS WITHIN THE TEMPERATURE RANGE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 1F MODE REPLY 0 CHQKJ /D/ 10NUMBER,IODINE IODINE NUMBER A NUMBER,OR VALUE,EXPRESSING THE PERCENTAGE OF IODINE ABSORBED BY A SUBSTANCE. 1D AND 1B MODE REPLY11AC20 CHQLJ 10NUMBER,ACID ACID NUMBER A NUMBER,OR VALUE,WHICH REPRESENTS THE NUMBER OF MILLIGRAMS OF POTASSIUM HYDROXIDE REQUIRED TO NEUTRALIZE THE FREE FATTY ACIDS IN A GRAM OF SUBSTANCE. 1D AND 1B MODE REPLY11AC20 CHQMJ /D/ 10NUMBER,SAPONIFICATION SAPONIFICATION NUMBER THE NUMBER OF MILLIGRAMS OF POTASSIUM HYDROXIDE REQUIRED FOR THE COMPLETE SAPONIFICATION OF ONE GRAM OF SUBSTANCE. 1D AND 1B MODE REPLY11AC20 CHQND 18TYPE,GUARD,SAFETY SAFETY GUARD TYPE INDICATES THE TYPE OF SAFETY GUARD(S) PROVIDED. SELECT REPLY CODE 10AK54 CHQPJ 04LENGTH,OVERALL,MAXIMUM MAXIMUM OVERALL LENGTH A MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CHQQJ 04WIDTH,OVERALL,MAXIMUM MAXIMUM OVERALL WIDTH THE MAXIMUM MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CHQRJ 04HEIGHT,OVERALL,MAXIMUM MAXIMUM OVERALL HEIGHT THE MAXIMUM DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM. 1D AND 1B MODE REPLY11AA05 CHQSJ /D/ 04LENGTH,OVERALL,STAND STAND OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE STAND. 2D AND 1B MODE REPLY21AA051AC20 CHQTJ /D/ 04WIDTH,OVERALL,STAND STAND OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A STAND,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CHQWJ 04HEIGHT,OVERALL,STAND STAND OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE STAND. 2D AND 1B MODE REPLY21AA051AC20 CHQXD /D/ 18TYPE,VARIETAL VARIETAL TYPE THE NAME OR PHASE WHICH REPRESENTS THE SUBDIVISION OF A VARIETY. SELECT REPLY CODE 10AL42 CHQYA /D/ 10TIME IN DAYS,MATURITY MATURITY TIME IN DAYS THE AVERAGE NUMBER OF DAYS REQUIRED FOR MATURITY. 1A MODE REPLY 0 CHQZD 03DESIGNATION,PROPAGATION PROPAGATION DESIGNATION THE DESIGNATION BY WHICH THE PROPAGATION OF AN ITEM IS IDENTIFIED. SELECT REPLY CODE 10AH50 CHRBD /D/ 18TYPE,RESISTANCE RESISTANCE TYPE INDICATES THE FACTOR(S) TO WHICH THE ITEM IS RESISTANT. SELECT REPLY CODE 10AA65 CHRCB 10PERCENTAGE,CONTENT,MAXIMUM WEED SEED MAXIMUM WEED SEED CONTENT PERCENTAGE THE MAXIMUM WEED SEED CONTENT,EXPRESSED IN PERCENT. 1B MODE REPLY 0 CHRDD 19PROTECTION FOR WHICH CARTRIDGE IS DESIGNED PROTECTION FOR WHICH CARTRIDGE IS DESIGNED AN INDICATION OF THE PROTECTION FOR WHICH THE CARTRIDGE IS DESIGNED. SELECT REPLY CODE 10AA65 CHRFD /D/ 18TYPE,FACILITY,FILING FILING FACILITY TYPE INDICATES THE TYPE OF FACILITY(IES) PROVIDED FOR FILING. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. SELECT REPLY CODE 10AK54 CHRGD /D/ 07FEATURE,PAPER,INTERLEAVED W/CARBON INTERLEAVED W/CARBON PAPER FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE IS INCLUDED FOR THE ITEM TO BE INTERLEAVED WITH CARBON PAPER. SELECT REPLY CODE 10AA49 CHRHG /D/ 19NUMBER,IDENTIFYING,PUBLISHER PUBLISHER IDENTIFYING NUMBER THE NUMBER ASSIGNED TO THE ITEM BY THE PUBLISHER FOR IDENTIFICATION. FULL TEXT WRITE-IN 0 CHRJJ 04WIDTH,SHEET SHEET WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SHEET,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CHRKJ 04LENGTH,SHEET SHEET LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SHEET,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CHRLA 12QUANTITY,PERFORATION,RING RING PERFORATION QUANTITY THE NUMBER OF RING PERFORATIONS PROVIDED. 1A MODE REPLY 0 CHRMD /D/ 13THREAD SERIES DESIGNATOR,STUD,MOUNTING MOUNTING STUD THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF DIAMETERS OF A MOUNTING STUD. SELECT REPLY CODE 10AH06 CHRNJ /D/ 13THREAD DIAMETER,STUD,MOUNTING MOUNTING STUD THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE MOUNTING STUD,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CHRPA /D/ 13THREAD QUANTITY PER INCH,STUD,MOUNTING MOUNTING STUD THREAD QUANTITY PER INCH THE NUMBER OF THREADS ON THE MOUNTING STUD PER LINEAR INCH MEASURE ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CHRQJ /D/ 04DEPTH TO GAGE,THROAT THROAT DEPTH TO GAGE A MEASUREMENT OF THE DEPTH OF THE THROAT TO GAGE. 1D AND 1B MODE REPLY11AA05 CHRRG 04THICKNESS ACCOMMODATED,METAL METAL THICKNESS ACCOMMODATED A MEASUREMENT OF THE SMALLEST DIMENSION OF THE METAL THE ITEM WILL ACCOMMODATE,IN DISTINCTION FROM LENGTH OR WIDTH. FULL TEXT WRITE-IN 0 CHRSJ 04WIDTH,WORKING WORKING WIDTH A MEASUREMENT OF THE WORKING WIDTH OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CHRTG 12QUANTITY/TYPE/SIZE/CAPACITY,ROLL ROLL QUANTITY/TYPE/SIZE/CAPACITY AN INDICATION OF THE NUMBER,TYPE,SIZE,OR CAPACITY OF A ROLL. FULL TEXT WRITE-IN 0 CHRWD 11METHOD,ADJUSTMENT,ROLL ROLL ADJUSTMENT METHOD THE MEANS USED FOR ADJUSTING THE ROLL(S). SELECT REPLY CODE 10AL41 CHRXJ 04DIAMETER ACCOMMODATED,INSIDE,MINIMUM,TUBE TUBE MINIMUM INSIDE DIAMETER ACCOMMODATED THE SMALLEST MEASUREMENT OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A TUBE THE ITEM IS DESIGNED TO ACCOMMODATE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CHRYJ 04DIAMETER,EXPANSION,RATED RATED EXPANSION DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE EXPANSION FOR WHICH THE ITEM IS RATED,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CHRZJ 04THICKNESS,MAXIMUM,TUBE SHEET TUBE SHEET MAXIMUM THICKNESS A MAXIMUM MEASUREMENT OF THE SMALLEST DIMENSION OF THE TUBE SHEET,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 CHSBD /D/ 07RING,GUARD GUARD RING AN INDICATION OF WHETHER OR NOT A GUARD RING IS INCLUDED. SELECT REPLY CODE 10AA49 CHSCJ 04LENGTH,EFFECTIVE,ROLLER ROLLER EFFECTIVE LENGTH A MEASUREMENT OF THE LONGEST EFFECTIVE DIMENSION OF THE ROLLER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CHSDD 18TYPE,MANDREL MANDREL TYPE INDICATES THE TYPE OF MANDREL. SELECT REPLY CODE 10AK84 CHSFD /D/ 07TIP,FLEXIBLE FLEXIBLE TIP AN INDICATION OF WHETHER OR NOT A FLEXIBLE TIP IS INCLUDED. SELECT REPLY CODE 10AA49 CHSGJ 04LENGTH,SECTION,HEAD HEAD SECTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE HEAD SECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CHSHJ /D/ 04LENGTH,SECTION,STRAIGHT,SECOND SECOND STRAIGHT SECTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SECOND STRAIGHT SECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CHSJJ /D/ 04LENGTH,SECTION,STRAIGHT,THIRD THIRD STRAIGHT SECTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE THIRD STRAIGHT SECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CHSKA 19NUMBER,SIZE,MORSE TAPER HEAD MORSE TAPER HEAD SIZE NUMBER AN INDICATION OF THE MORSE TAPER HEAD SIZE NUMBER. 1A MODE REPLY 0 CHSLJ 04WIDTH ACROSS FLATS,HEAD,SQUARE SQUARE HEAD WIDTH ACROSS FLATS THE DISTANCE FROM ONE FLAT TO THE OPPOSITE FLAT OF THE SQUARE HEAD. 2D AND 1B MODE REPLY21AA051AC20 CHSND /D/ 18TYPE FOR WHICH DESIGNED,RIM RIM TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF RIM FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 CHSPD 19CHARACTERISTIC,TIRE TIRE CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC OF THE TIRE. SELECT REPLY CODE 10AJ88 CHSQD 19CHARACTERISTIC,ARRANGEMENT,TIRE TIRE ARRANGEMENT CHARACTERISTIC THE CHARACTERISTIC ARRANGEMENT OF THE TIRE/S/. SELECT REPLY CODE 10AH86 CHSRA 04SIZE FOR WHICH DESIGNED,TIRE TIRE SIZE FOR WHICH DESIGNED DESIGNATES THE TIRE SIZE FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 CHSSJ 04DISTANCE FROM RIM CENTERLINE TO OUTSIDE OF WHEEL MOUNTING,OFFSET OFFSET DISTANCE FROM RIM CENTERLINE TO OUTSIDE OF WHEEL MOUNTING THE OFFSET DISTANCE FROM THE CENTERLINE OF THE RIM TO OUTSIDE OF WHEEL MOUNTING. 2D AND 1B MODE REPLY21AA051AC20 CHSTJ 04DIAMETER,OVERALL,RIM RIM OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF THE RIM. 2D AND 1B MODE REPLY21AA051AC20 CHSWD /D/ 07FEATURE,TREAD,SOFT SOFT TREAD FEATURE AN INDICATION OF WHETHER OR NOT A SOFT TREAD FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CHSXJ 04DIAMETER,RECESS,AXLE AXLE RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CHSYJ 04DIAMETER,MAJOR,AXLE RECESS AXLE RECESS MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CHSZJ 04DIAMETER,MINOR,AXLE RECESS AXLE RECESS MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CHTBJ 04DIAMETER,RECESS,SAND BAND SAND BAND RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CHTCJ 04DIAMETER,MAJOR,SAND BAND RECESS SAND BAND RECESS MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CHTDJ 04DIAMETER,MINOR,SAND BAND RECESS SAND BAND RECESS MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CHTFJ 04DIAMETER,RECESS,BEARING BEARING RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CHTGJ 04DEPTH,RECESS,SAND BAND SAND BAND RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CHTHJ 04DEPTH,RECESS,SAND BAND,MAJOR MAJOR SAND BAND RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CHTJJ 04DEPTH,RECESS,SAND BAND,MINOR MINOR SAND BAND RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CHTKJ 04DEPTH,RECESS,BEARING BEARING RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CHTMD /D/ 07BLOWER,AIR AIR BLOWER AN INDICATION OF WHETHER OR NOT AN AIR BLOWER IS INCLUDED. SELECT REPLY CODE 10AA49 CHTNG 10DISCHARGED AT RATED VELOCITY,AIR,RATED RATED AIR DISCHARGED AT RATED VELOCITY THE VOLUME OF DISCHARGED AIR RELATIVE TO THE RATED SPEED OF THE ITEM. FULL TEXT WRITE-IN 0 CHTPA 12QUANTITY,NOZZLE,DISCHARGE DISCHARGE NOZZLE QUANTITY THE NUMBER OF DISCHARGE NOZZLES PROVIDED. 1A MODE REPLY 0 CHTQG 10DISCHARGE RATE AT SPECIFIED PRESSURE,MAXIMUM MAXIMUM DISCHARGE RATE AT SPECIFIED PRESSURE THE MAXIMUM AMOUNT OF DISCHARGE AT A SPECIFIED PRESSURE. FULL TEXT WRITE-IN 0 CHTRD /D/ 07REGULATOR,PRESSURE PRESSURE REGULATOR AN INDICATION OF WHETHER OR NOT A PRESSURE REGULATOR IS INCLUDED. SELECT REPLY CODE 10AA49 CHTSD /D/ 07TANK,SOLUTION SOLUTION TANK AN INDICATION OF WHETHER OR NOT A SOLUTION TANK IS INCLUDED. SELECT REPLY CODE 10AA49 CHTTD 18TYPE,PUMP,SOLUTION SOLUTION PUMP TYPE INDICATES THE TYPE OF SOLUTION PUMP PROVIDED. SELECT REPLY CODE 10AK95 CHTWD 07REMOVABILITY,TOP,TANK TANK TOP REMOVABILITY AN INDICATION OF WHETHER OR NOT THE TANK TOP IS REMOVABLE. SELECT REPLY CODE 10AB00 CHTXJ /D/ 04SIZE ACCOMMODATED,DRUM DRUM SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE DRUM THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY12AG67 CHTYH /D/ 19SYSTEM PER FUNCTION FOR WHICH DESIGNED SYSTEM PER FUNCTION FOR WHICH DESIGNED THE SYSTEM USED PER FUNCTION FOR WHICH THE ITEM IS DESIGNED. 2D MODE REPLY 22AE812AH19 CHTZJ 10CURRENT RATING,SATURATION SATURATION CURRENT RATING THE AMOUNT OF CONTROL CURRENT BEYOND WHICH AN INCREASE IN CONTROL CURRENT PRODUCES NO INCREASE IN THE ITEMS OUTPUT. 1D AND 1B MODE REPLY11AC30 CHWBJ A19COMPONENTS AND QUANTITY,ACCESSORY ACCESSORY COMPONENTS AND QUANTITY THE NAME AND NUMBER OF ACCESSORY COMPONENTS SUPPLIED WITH THE ITEM WHICH MAY BE REQUIRED FOR APPLICATION. 1D AND 1A MODE REPLY13AL37 CHWCD 07ADJUSTABILITY,SPRAY SPRAY ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE SPRAY IS ADJUSTABLE. SELECT REPLY CODE 10AB00 CHWDD /D/ 07VALVE,CONTROL,DISCHARGE DISCHARGE CONTROL VALVE AN INDICATION OF WHETHER OR NOT A DISCHARGE CONTROL VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 CHWFA 12QUANTITY,HOSE,DISCHARGE DISCHARGE HOSE QUANTITY THE NUMBER OF DISCHARGE HOSES PROVIDED. 1A MODE REPLY 0 CHWGD /D/ 07TANK,PRESSURE,SEPARATE SEPARATE PRESSURE TANK AN INDICATION OF WHETHER OR NOT A SEPARATE PRESSURE TANK IS INCLUDED. SELECT REPLY CODE 10AA49 CHWHG /D/ 10DISCHARGE RATE,COMPRESSOR,AIR AIR COMPRESSOR DISCHARGE RATE THE RATED DISCHARGE OF THE AIR COMPRESSOR. FULL TEXT WRITE-IN 0 CHWJD /D/ 07PANEL,CONTROL CONTROL PANEL AN INDICATION OF WHETHER OR NOT A CONTROL PANEL IS INCLUDED. SELECT REPLY CODE 10AA49 CHWKD /D/ 07FEATURE,EXTENSION,WHEEL WHEEL EXTENSION FEATURE AN INDICATION OF WHETHER OR NOT A WHEEL EXTENSION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CHWLJ /D/T10RANGE,EXTENSION,WHEEL WHEEL EXTENSION RANGE THE MINIMUM TO MAXIMUM LIMITS TO WHICH THE WHEEL/S/ CAN BE EXTENDED. 1D AND 1F MODE REPLY11AA05 CHWMJ 10CAPACITY,TANK,SOLUTION SOLUTION TANK CAPACITY THE SOLUTION TANK CAPACITY. 1D AND 1B MODE REPLY12AG67 CHWNJ 04LENGTH,OVERALL,BASE,CRAWLER CRAWLER BASE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CRAWLER BASE. 2D AND 1B MODE REPLY21AA051AC20 CHWPJ 04WIDTH,OVERALL,CRAWLER BASE CRAWLER BASE OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CRAWLER BASE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CHWQJ 04WIDTH,SHOE,CRAWLER TRACK CRAWLER TRACK SHOE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CRAWLER TRACK SHOE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CHWRD /D/ 07ATTACHMENT,SHOVEL SHOVEL ATTACHMENT AN INDICATION OF WHETHER OR NOT A SHOVEL ATTACHMENT IS INCLUDED. SELECT REPLY CODE 10AA49 CHWSJ 04HEIGHT,DUMPING,MAXIMUM MAXIMUM DUMPING HEIGHT THE MAXIMUM MEASUREMENT OF THE DUMPING HEIGHT OF THE ITEM. 1D AND 1B MODE REPLY11AA05 CHWTJ 04RADIUS,DUMPING,MAXIMUM MAXIMUM DUMPING RADIUS THE MAXIMUM MEASUREMENT OF THE DUMPING RADIUS OF THE ITEM. 1D AND 1B MODE REPLY11AA05 CHWWJ 04HEIGHT,DIGGING,MAXIMUM MAXIMUM DIGGING HEIGHT THE MAXIMUM MEASUREMENT OF THE DIGGING HEIGHT OF THE ITEM. 1D AND 1B MODE REPLY11AA05 CHWXJ 04RADIUS,DIGGING,MAXIMUM MAXIMUM DIGGING RADIUS THE MAXIMUM MEASUREMENT OF THE DIGGING RADIUS OF THE ITEM. 1D AND 1B MODE REPLY11AA05 CHWYJ 10CUT,MAXIMUM,BELOW FLOOR LEVEL MAXIMUM CUT BELOW FLOOR LEVEL THE MAXIMUM MEASUREMENT OF THE CUT BELOW FLOOR LEVEL. 1D AND 1B MODE REPLY11AA05 CHWZD /D/ 07BACKHOE BACKHOE AN INDICATION OF WHETHER OR NOT A BACKHOE IS INCLUDED. SELECT REPLY CODE 10AA49 CHXBJ 04DEPTH,DIGGING,MAXIMUM,BACKHOE BACKHOE MAXIMUM DIGGING DEPTH THE MAXIMUM MEASUREMENT OF THE DIGGING DEPTH OF THE BACKHOE. 1D AND 1B MODE REPLY11AA05 CHXCJ 04RADIUS,DIGGING,MAXIMUM,BACKHOE BACKHOE MAXIMUM DIGGING RADIUS THE MAXIMUM MEASUREMENT OF THE DIGGING RADIUS OF THE BACKHOE. 1D AND 1B MODE REPLY11AA05 CHXDJ 04HEIGHT,DUMPING,MAXIMUM,BACKHOE BACKHOE MAXIMUM DUMPING HEIGHT THE MAXIMUM MEASUREMENT OF THE DUMPING HEIGHT OF THE BACKHOE. 1D AND 1B MODE REPLY11AA05 CHXFJ 04RADIUS,DUMPING,MAXIMUM,BACKHOE BACKHOE MAXIMUM DUMPING RADIUS THE MAXIMUM MEASUREMENT OF THE DUMPING RADIUS OF THE BACKHOE. 1D AND 1B MODE REPLY11AA05 CHXGD /D/ 07DRIVER,PILE PILE DRIVER AN INDICATION OF WHETHER OR NOT A PILE DRIVER IS INCLUDED. SELECT REPLY CODE 10AA49 CHXHJ 10WEIGHT,HAMMER HAMMER WEIGHT A RELATIVE MEASURE OF THE MASS OF THE HAMMER WITH RESPECT TO ITS DENSITY. 2D AND 1B MODE REPLY22AG671AC20 CHXJJ 04DIAMETER ACCOMMODATED,PILE,MAXIMUM MAXIMUM PILE DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR A PILE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CHXKD /D/ 07CAB,OPERATOR,CRANE CRANE OPERATOR CAB AN INDICATION OF WHETHER OR NOT A CRANE OPERATOR(S) CAB IS INCLUDED. SELECT REPLY CODE 10AA49 CHXLD 18TYPE,SYSTEM,LIGHTING LIGHTING SYSTEM TYPE INDICATES THE TYPE OF LIGHTING SYSTEM PROVIDED. SELECT REPLY CODE 10AK54 CHXMD 18TYPE,BOOM BOOM TYPE INDICATES THE TYPE OF BOOM PROVIDED. SELECT REPLY CODE 10AK54 CHXNJ 04LENGTH,OVERHANG,BOOM BOOM OVERHANG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BOOM OVERHANG,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CHXPJ 04DISTANCE BETWEEN TRESTLE SUPPORTING MEMBERS,MAXIMUM MAXIMUM DISTANCE BETWEEN TRESTLE SUPPORTING MEMBERS THE MAXIMUM DISTANCE BETWEEN THE TRESTLE SUPPORTING MEMBERS. 1D AND 1B MODE REPLY11AA05 CHXQD 18TYPE,LEAD,DRUM DRUM LEAD TYPE INDICATES THE TYPE OF DRUM LEAD PROVIDED. SELECT REPLY CODE 10AK54 CHXRD 11METHOD,LOCKING,LOAD POSITION LOAD POSITION LOCKING METHOD THE MEANS UTILIZED FOR LOCKING A LOAD IN A FIXED POSITION. SELECT REPLY CODE 10AE44 CHXSD /D/ 07FEATURE,BED BED FEATURE AN INDICATION OF WHETHER OR NOT A BED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CHXTA 10PROPORTION,SCALE SCALE PROPORTION INDICATES THE PROPORTIONAL SCALE OF THE ITEM. 1A MODE REPLY 0 CHXWA 12QUANTITY PER SET,CARD CARD QUANTITY PER SET THE NUMBER OF CARDS INCLUDED IN EACH SET. 1A MODE REPLY 0 CHXXA 12QUANTITY,MOTOR MOTOR QUANTITY THE NUMBER OF MOTORS PROVIDED. 1A MODE REPLY 0 CHXYJ 10LOAD RATING,BOOM BOOM LOAD RATING THE RATED LOAD THAT THE BOOM IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY12AG67 CHXZD /D/ 07SWIVEL,TRUCK,END END TRUCK SWIVEL AN INDICATION OF WHETHER OR NOT AN END TRUCK SWIVEL IS INCLUDED. SELECT REPLY CODE 10AA49 CHYBJ /D/ 04DISTANCE BETWEEN GANTRY SUPPORTS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN GANTRY SUPPORTS THE CENTER TO CENTER DISTANCE BETWEEN THE GANTRY SUPPORTS. 3D AND 1B MODE REPLY31AA051AC203AM39 CHYCJ 04DISTANCE FROM BOTTOM OF GANTRY BRIDGE TO GROUND LEVEL DISTANCE FROM BOTTOM OF GANTRY BRIDGE TO GROUND LEVEL THE DISTANCE FROM THE BOTTOM OF THE GANTRY BRIDGE TO GROUND LEVEL. 2D AND 1B MODE REPLY21AA051AC20 CHYDJ /D/ 04DISTANCE FROM GROUND LEVEL TO BOOM PIN CENTER DISTANCE FROM GROUND LEVEL TO BOOM PIN CENTER THE DISTANCE FROM GROUND LEVEL TO THE CENTER OF THE BOOM PIN. 2D AND 1B MODE REPLY21AA051AC20 CHYFJ 04DISTANCE,CLEARANCE CLEARANCE DISTANCE THE CLEARANCE DISTANCE OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CHYGG 10CAPACITY AT SPECIFIED RADIUS,BOOM BOOM CAPACITY AT SPECIFIED RADIUS THE WEIGHT THE BOOM IS DESIGNED TO ACCOMMODATE AT A SPECIFIED RADIUS. FULL TEXT WRITE-IN 0 CHYHJ 10LIFTING CAPACITY,MAXIMUM,BOOM BOOM MAXIMUM LIFTING CAPACITY THE MAXIMUM WEIGHT THE BOOM IS DESIGNED TO LIFT. 1D AND 1B MODE REPLY12AG67 CHYJD 11METHOD,OPERATION,BOOM BOOM OPERATION METHOD THE MEANS USED TO OPERATE THE BOOM. SELECT REPLY CODE 10AC58 CHYKJ 04DIAMETER,DRUM,BOOM BOOM DRUM DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOOM DRUM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CHYLJ 04LENGTH,DRUM,BOOM BOOM DRUM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BOOM DRUM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CHYMG /D/ 04LENGTH AND SIZE ACCOMMODATED,CABLE,BOOM DRUM BOOM DRUM CABLE LENGTH AND SIZE ACCOMMODATED THE LENGTH OF A CABLE OF A GIVEN SIZE THAT THE BOOM DRUM WILL ACCOMMODATE. FULL TEXT WRITE-IN 0 CHYNG /D/ 19ARMAMENT/GUN MOUNT TYPE/MODEL NUMBER AND QUANTITY ARMAMENT/GUN MOUNT TYPE/MODEL NUMBER AND QUANTITY INDICATES THE TYPE,MODEL NUMBER,AND NUMBER OF EACH ARMAMENT AND GUN MOUNT. FULL TEXT WRITE-IN 0 CHYPJ 04LENGTH,TRACK,GROUND GROUND TRACK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF TRACK ON THE GROUND. 2D AND 1B MODE REPLY21AA051AC20 CHYQJ 04DISTANCE BETWEEN TRACKS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN TRACKS THE CENTER TO CENTER DISTANCE BETWEEN THE TRACKS. 2D AND 1B MODE REPLY21AA051AC20 CHYRD 08LOCATION,DRIVE,FINAL FINAL DRIVE LOCATION INDICATES THE LOCATION OF THE FINAL DRIVE ON THE ITEM. SELECT REPLY CODE 10AJ91 CHYSJ 04DISTANCE BETWEEN WHEELS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN WHEELS THE CENTER TO CENTER DISTANCE BETWEEN THE WHEELS. 2D AND 1B MODE REPLY21AA051AC20 CHYTD /D/ 07TRANSMISSION,AUXILIARY AUXILIARY TRANSMISSION AN INDICATION OF WHETHER OR NOT AN AUXILIARY TRANSMISSION IS INCLUDED. MRC IS DISCONTINUED AND REPLACED WITH MRC CBBL AND REPLY CODE GSW, AUXILIARY TRANSMISSION ON 03/28/2024. SELECT REPLY CODE 10AA49 CHYWD /D/ 07TRANSMISSION,TRANSFER TRANSFER TRANSMISSION AN INDICATION OF WHETHER OR NOT A TRANSFER TRANSMISSION IS INCLUDED. MRC DISCONTINUED AND REPLACED WITH MRC CBBL AND REPLY CODE GSX, TRANSFER CASE ON 03/28/2024. SELECT REPLY CODE 10AA49 CHYXD /D/ 07FEATURE,TAKEOFF,POWER POWER TAKEOFF FEATURE AN INDICATION OF WHETHER OR NOT A POWER TAKEOFF FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CHYYD /D/ 07ROLLER,FRONT,SPRING MOUNTED SPRING MOUNTED FRONT ROLLER AN INDICATION OF WHETHER OR NOT A SPRING MOUNTED FRONT ROLLER(S) IS INCLUDED. MRC DISCONTIUED AND REPLACED WITH MRC ABFF, REPLY CODE CPZ, CASTERS ON 03/28/2024. SELECT REPLY CODE 10AA49 CHYZA 12QUANTITY,WINCH WINCH QUANTITY THE NUMBER OF WINCHES PROVIDED. 1A MODE REPLY 0 CHZBD /D/ 07HEAD,GYPSY GYPSY HEAD AN INDICATION OF WHETHER OR NOT A GYPSY HEAD(S) IS INCLUDED. MRC DISCONTINUED AND REPLACED WITH MRC ABFF AND REPLY CODE BFG, CHAIN WHEEL ON 03/28/2024. SELECT REPLY CODE 10AA49 CHZCB 10VOLTAGE RATING,SYSTEM,STARTING STARTING SYSTEM VOLTAGE RATING THE ELECTRICAL VOLTAGE OF THE STARTING SYSTEM FOR WHICH THE ITEM IS DESIGNED. 1B MODE REPLY 0 CHZDB 10VOLTAGE RATING,SYSTEM,LIGHTING LIGHTING SYSTEM VOLTAGE RATING THE ELECTRICAL VOLTAGE OF THE LIGHTING SYSTEM FOR WHICH THE ITEM IS DESIGNED. 1B MODE REPLY 0 CHZFD /D/ 07SET,GENERATOR,AUXILIARY AUXILIARY GENERATOR SET AN INDICATION OF WHETHER OR NOT AN AUXILIARY GENERATOR SET(S) IS INCLUDED. MRC DISCONTINUED AND REPLACED WITH MRC CBBL AND REPLY CODE GKH, AUXILIARY GENERATOR SET ON 03/28/2024. SELECT REPLY CODE 10AA49 CHZGD 18TYPE,CONNECTION,TRAILER BRAKE TRAILER BRAKE CONNECTION TYPE INDICATES THE TYPE OF TRAILER BRAKE CONNECTION(S) PROVIDED ON THE ITEM. SELECT REPLY CODE 10AG25 CHZHD /D/ 18TYPE,TIRE,BOGIE WHEEL BOGIE WHEEL TIRE TYPE INDICATES THE TYPE OF BOGIE WHEEL TIRE(S) PROVIDED. SELECT REPLY CODE 10AH67 CHZJD /D/ 07FEATURE,COOLING,ENGINE AIR ENGINE AIR COOLING FEATURE AN INDICATION OF WHETHER OR NOT AN ENGINE AIR COOLING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CHZKB 10VOLTAGE RATING,SYSTEM,IGNITION IGNITION SYSTEM VOLTAGE RATING THE ELECTRICAL VOLTAGE OF THE IGNITION SYSTEM FOR WHICH THE ITEM IS DESIGNED. 1B MODE REPLY 0 CHZLJ /D/ 04DISTANCE,CAB BACK TO FRAME END CAB BACK TO FRAME END DISTANCE THE DISTANCE FROM THE BACK OF THE CAB TO THE END OF THE FRAME. 2D AND 1B MODE REPLY21AA051AC20 CHZMA 12QUANTITY,WHEEL,FRONT FRONT WHEEL QUANTITY THE NUMBER OF FRONT WHEELS PROVIDED ON THE ITEM. 1A MODE REPLY 0 CHZND 19CHARACTERISTIC,ARRANGEMENT,FRONT WHEEL FRONT WHEEL ARRANGEMENT CHARACTERISTIC THE ARRANGEMENT CHARACTERISTIC/S/ OF THE FRONT WHEELS. SELECT REPLY CODE 10AH86 CHZPD 18TYPE,TIRE,FRONT FRONT TIRE TYPE INDICATES THE TYPE OF FRONT TIRE(S) PROVIDED. SELECT REPLY CODE 10AH67 CHZQD /D/ 07FEATURE,DRIVE,FRONT WHEEL FRONT WHEEL DRIVE FEATURE AN INDICATION OF WHETHER OR NOT A FRONT WHEEL DRIVE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CHZRD /D/ 07FEATURE,STEERABLE,FRONT WHEEL FRONT WHEEL STEERABLE FEATURE AN INDICATION OF WHETHER OR NOT A FRONT WHEEL STEERABLE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CHZSA 12QUANTITY,WHEEL,REAR REAR WHEEL QUANTITY THE NUMBER OF REAR WHEELS PROVIDED ON THE ITEM. 1A MODE REPLY 0 CHZTD 19CHARACTERISTIC,ARRANGEMENT,REAR WHEEL REAR WHEEL ARRANGEMENT CHARACTERISTIC THE ARRANGEMENT CHARACTERISTIC/S/ OF THE REAR WHEELS. SELECT REPLY CODE 10AH86 CHZWD 18TYPE,TIRE,REAR REAR TIRE TYPE INDICATES THE TYPE OF REAR TIRE(S) PROVIDED. SELECT REPLY CODE 10AH67 CHZXD /D/ 07FEATURE,DRIVE,REAR WHEEL REAR WHEEL DRIVE FEATURE AN INDICATION OF WHETHER OR NOT A REAR WHEEL DRIVE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CHZYD /D/ 07FEATURE,STEERABLE,REAR WHEEL REAR WHEEL STEERABLE FEATURE AN INDICATION OF WHETHER OR NOT A REAR WHEEL STEERABLE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CHZZJ 04WIDTH BETWEEN FRONT WHEELS,TREAD,CENTER TO CENTER CENTER TO CENTER TREAD WIDTH BETWEEN FRONT WHEELS THE CENTER TO CENTER TREAD WIDTH BETWEEN THE FRONT WHEELS. 2D AND 1B MODE REPLY21AA051AC20 CJBBJ 04WIDTH BETWEEN REAR WHEELS,TREAD,CENTER TO CENTER CENTER TO CENTER TREAD WIDTH BETWEEN REAR WHEELS A MEASUREMENT OF THE TREAD WIDTH BETWEEN THE REAR WHEEL CENTERS. 2D AND 1B MODE REPLY21AA051AC20 CJBCD 07LIMITATION,OPERATION,HARD SURFACE HARD SURFACE OPERATION LIMITATION AN INDICATION OF WHETHER OR NOT THE ITEM IS LIMITED TO HARD SURFACE OPERATION. SELECT REPLY CODE 10AJ98 CJBDJ 10UNDERCLEARANCE,MINIMUM MINIMUM UNDERCLEARANCE THE MINIMUM DISTANCE BETWEEN THE GROUND SURFACE AND THE BOTTOM OF THE ITEM. 1D AND 1B MODE REPLY11AA05 CJBFD /D/ 07WINCH,MOUNTED,INTEGRALLY INTEGRALLY MOUNTED WINCH AN INDICATION OF WHETHER OR NOT AN INTEGRALLY MOUNTED WINCH(S) IS INCLUDED. MRC DISCONTINUED AND REPLACED WITH MRC CBBL AND REPLY CODE FWJ, WINCH ON 03/28/2024. SELECT REPLY CODE 10AA49 CJBGD /D/ 07PROVISION,STOWAGE,TOW BAR/WHEEL CHOCK TOW BAR/WHEEL CHOCK STOWAGE PROVISION AN INDICATION OF WHETHER OR NOT A PROVISION FOR TOW BAR/S/ AND WHEEL CHOCK/S/ STOWAGE IS INCLUDED. SELECT REPLY CODE 10AA49 CJBHD /D/ 07FEATURE,DESIGN,OPERATOR CAB ALL WEATHER OPERATION OPERATOR CAB ALL WEATHER OPERATION DESIGN FEATURE AN INDICATION OF WHETHER OR NOT AN ALL WEATHER OPERATION DESIGN FEATURE IS INCLUDED ON THE OPERATOR CAB. SELECT REPLY CODE 10AA49 CJBJG 19NOMENCLATURE AND QUANTITY,ATTACHMENT ATTACHMENT NOMENCLATURE AND QUANTITY AN INDICATION OF THE COMPLETE NOMENCLATURE OF THE ATTACHMENT/S/ ON THE ITEM,AND THE NUMBER OF EACH. FULL TEXT WRITE-IN 0 CJBKD /D/ 07CONDITIONER,AIR AIR CONDITIONER AN INDICATION OF WHETHER OR NOT AN AIR CONDITIONER/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CJBLD /D/ 07EQUIPMENT,SERVICING,AUXILIARY POWER AUXILIARY POWER SERVICING EQUIPMENT AN INDICATION OF WHETHER OR NOT AUXILIARY POWER SERVICING EQUIPMENT IS INCLUDED. SELECT REPLY CODE 10AA49 CJBMG 10OUTPUT RATING IN GPM AT PSI OUTPUT RATING IN GPM AT PSI THE RATED CAPACITY OF THE FLUID OUTPUT DELIVERED BY THE ITEM,EXPRESSED IN GALLONS PER MINUTE AT POUNDS PER SQUARE INCH. FULL TEXT WRITE-IN 0 CJBND /D/ 09MATERIAL,DEVICE,AIR INTAKE AIR INTAKE DEVICE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE AIR INTAKE DEVICE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CJBPJ 04THICKNESS,OVERALL,WALL WALL OVERALL THICKNESS AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF THE WALL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CJBQJ 04DIAMETER,LUMEN LUMEN DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR LUMEN,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJBRJ 10SIZE ACCOMMODATED,CATHETER CATHETER SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE ACCOMMODATED CATHETER. 2D AND 1B MODE REPLY21AF981AC20 CJBSJ 04LENGTH ACCOMMODATED,MAXIMUM,NEEDLE NEEDLE MAXIMUM LENGTH ACCOMMODATED THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF A NEEDLE THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 CJBTA 12QUANTITY ACCOMMODATED,NEEDLE NEEDLE QUANTITY ACCOMMODATED THE NUMBER OF NEEDLES ACCOMMODATED. 1A MODE REPLY 0 CJBWA 12QUANTITY,CONSTRICTION CONSTRICTION QUANTITY THE NUMBER OF CONSTRICTIONS PROVIDED. 1A MODE REPLY 0 CJBXD /D/ 07KNURL KNURL AN INDICATION OF WHETHER OR NOT A KNURL IS INCLUDED. MRC DISCONTINUED AND REPLACED WITH MRC ABFF AND REPLY CODE CVE, KNURLED HUB ON 03/28/2024. SELECT REPLY CODE 10AA49 CJBYD /D/ 07FLANGE,LOCKING,SYRINGE SYRINGE LOCKING FLANGE AN INDICATION OF WHETHER OR NOT A SYRINGE LOCKING FLANGE IS INCLUDED. MRC DISCONTINUED AND REPLACED WITH MRC CBBL AND REPLY CODE EVM, LUER LOCK SAFETY DEVICE ON 03/28/2024. SELECT REPLY CODE 10AA49 CJBZD /D/ 07LUMEN,THREADED THREADED LUMEN AN INDICATION OF WHETHER OR NOT A THREADED LUMEN IS INCLUDED. MRC DISCONTINUED AND REPLACED WITH MRC CBBL AND REPLY CODES GSY, SINGLE LUMEN OR GSZ, DOUBLE LUMEN ON 03/28/2024. SELECT REPLY CODE 10AA49 CJCBD /D/ 07PROTECTOR,METAL METAL PROTECTOR AN INDICATION OF WHETHER OR NOT A METAL PROTECTOR IS INCLUDED. MRC DISCONTINUED AND REPLACED WITH MRC ABFF AND REPLY CODE AQB, PROTECTIVE CASE ON 03/28/2024. SELECT REPLY CODE 10AA49 CJCCD /D/ 19RELATIONSHIP TO CG AIDS TO NAVIGATION MANUAL,DESIGNATION,SHAPE/SIZE SHAPE/SIZE DESIGNATION RELATIONSHIP TO CG AIDS TO NAVIGATION MANUAL AN INDICATION OF WHETHER OR NOT THE RELATIONSHIP OF THE SHAPE AND SIZE DESIGNATIONS OF THE ITEM IS IN ACCORDANCE WITH THE COAST GUARD AIDS TO NAVIGATION MANUAL. SELECT REPLY CODE 10AB78 CJCDD /D/ 18TYPE,PERFORATION PERFORATION TYPE INDICATES THE TYPE OF PERFORATION PROVIDED. SELECT REPLY CODE 10AK95 CJCFD /D/ 07FEATURE,RECESSED RECESSED FEATURE AN INDICATION OF WHETHER OR NOT A RECESSED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CJCGD /D/ 07PORT,INLET INLET PORT AN INDICATION OF WHETHER OR NOT AN INLET PORT IS INCLUDED. MRC DISCONTINUED AND REPLACED WITH MRC CBBL AND REPLY CODE GTA, INLET PORT ON 03/28/2024. SELECT REPLY CODE 10AA49 CJCHA 10CALIBRATION,MILLIMETER,MAXIMUM MAXIMUM MILLIMETER CALIBRATION THE MAXIMUM CALIBRATION,OR READING,EXPRESSED IN MILLIMETERS. 1A MODE REPLY 0 CJCJD /D/ 09MATERIAL,ADAPTER ADAPTER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ADAPTER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CJCKJ /D/ 10EQUIVALENT,CAPACITY,WEIGHT WEIGHT CAPACITY EQUIVALENT THE LIQUID CAPACITY OF WHICH THE WEIGHT IS EQUIVALENT. 1D AND 1B MODE REPLY12AG67 CJCLD /D/ 07CLAMP,PINCH PINCH CLAMP AN INDICATION OF WHETHER OR NOT A PINCH CLAMP IS INCLUDED. SELECT REPLY CODE 10AA49 CJCMJ 04DIAMETER ACCOMMODATED,MAXIMUM,TUBING,INLET INLET TUBING MAXIMUM DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INLET TUBING ACCOMMODATED BY THE ITEM,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CJCNJ 04DIAMETER ACCOMMODATED,MAXIMUM,TUBING,OUTLET OUTLET TUBING MAXIMUM DIAMETER ACCOMMODATED THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTLET TUBING ACCOMMODATED BY THE ITEM,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CJCPD 08LOCATION,CODE,COLOR COLOR CODE LOCATION INDICATES THE LOCATION(S) OF AN ITEM THAT IS IDENTIFIED BY COLOR. SELECT REPLY CODE 10AJ91 CJCQA 12QUANTITY,END,FEMALE ADAPTER FEMALE ADAPTER END QUANTITY THE NUMBER OF FEMALE ADAPTER ENDS PROVIDED. 1A MODE REPLY 0 CJCRD /D/ 07END,ADAPTER,MALE MALE ADAPTER END AN INDICATION OF WHETHER OR NOT A MALE ADAPTER END IS INCLUDED. SELECT REPLY CODE 10AA49 CJCSJ 04LENGTH,TUBING,ATTACHED ATTACHED TUBING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ATTACHED TUBING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CJCTD /D/ 07ADAPTER,NEEDLE NEEDLE ADAPTER AN INDICATION OF WHETHER OR NOT A NEEDLE ADAPTER IS INCLUDED. SELECT REPLY CODE 10AA49 CJCWD /D/ 09MATERIAL,PAD,REMOVABLE PUNCTURE REMOVABLE PUNCTURE PAD MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE REMOVABLE PUNCTURE PAD IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CJCXD /D/ 09MATERIAL,COVERING,WINDOW WINDOW COVERING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WINDOW COVERING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CJCYJ 04WIDTH,INSIDE,WINDOW WINDOW INSIDE WIDTH AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE WINDOW OPENING. 2D AND 1B MODE REPLY21AA051AC20 CJCZJ 04HEIGHT,INSIDE,WINDOW WINDOW INSIDE HEIGHT AN INSIDE MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE WINDOW,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CJDBD /D/ 09MATERIAL,ORIFICE,JEWEL JEWEL ORIFICE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE JEWEL ORIFICE IS FABRICATED. SELECT REPLY CODE 10AD09 CJDCJ 04DIAMETER,OUTLET,ORIFICE ORIFICE OUTLET DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ORIFICE OUTLET,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJDDD /D/ 07ABRASIVE DISK BONDED TO NOZZLE ABRASIVE DISK BONDED TO NOZZLE AN INDICATION OF WHETHER OR NOT AN ABRASIVE DISK BONDED TO A NOZZLE IS INCLUDED. SELECT REPLY CODE 10AA49 CJDFD 08LOCATION,TAPER TAPER LOCATION INDICATES THE LOCATION OF THE TAPER ON THE ITEM. SELECT REPLY CODE 10AJ91 CJDGJ 04DIAMETER,INSIDE,TAPERED END TAPERED END INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TAPERED END OF AN ITEM,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJDHJ 04DIAMETER,OUTSIDE,TAPERED END TAPERED END OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TAPERED END OF AN ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJDJD 13THREAD LOCATION,END,THREADED THREADED END THREAD LOCATION THE PORTION OF THE THREADED END ON WHICH THE THREAD/S/ IS LOCATED. SELECT REPLY CODE 10AJ91 CJDKD 13THREAD LOCATION,STEM STEM THREAD LOCATION THE PORTION OF THE STEM ON WHICH THE THREAD(S) IS LOCATED. SELECT REPLY CODE 10AJ91 CJDLJ 04DIAMETER,INSIDE,THREADED END THREADED END INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED END OF AN ITEM,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJDMJ 04DIAMETER,OUTSIDE,THREADED END THREADED END OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED END OF AN ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJDNJ 10CAPACITY,TANK,DUST DUST TANK CAPACITY THE DUST TANK CAPACITY. 1D AND 1B MODE REPLY12AG67 CJDPD 19CHARACTERISTIC,SPRAY SPRAY CHARACTERISTIC AN INDICATION OF THE SPRAY CHARACTERISTIC. SELECT REPLY CODE 10AD63 CJDQD /D/ 07CONTAINER,LIQUID LIQUID CONTAINER AN INDICATION OF WHETHER OR NOT A LIQUID CONTAINER IS INCLUDED. SELECT REPLY CODE 10AA49 CJDRD /D/ 07INTERIOR,RESISTANT,RUST RUST RESISTANT INTERIOR AN INDICATION OF WHETHER OR NOT A RUST RESISTANT INTERIOR IS PROVIDED. SELECT REPLY CODE 10AB22 CJDSD /D/ 07VALVE,DISCHARGE DISCHARGE VALVE AN INDICATION OF WHETHER OR NOT A DISCHARGE VALVE IS INCLUDED. SELECT REPLY CODE 10AA49 CJDTD /D/ 07HOSE,DISCHARGE DISCHARGE HOSE AN INDICATION OF WHETHER OR NOT A DISCHARGE HOSE IS INCLUDED. SELECT REPLY CODE 10AA49 CJDWD /D/ 07TOP,REMOVABLE REMOVABLE TOP AN INDICATION OF WHETHER OR NOT A REMOVABLE TOP IS INCLUDED. PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AA49 CJDXD /D/ 07CONTROL,FEED FEED CONTROL AN INDICATION OF WHETHER OR NOT A FEED CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 CJDYJ /D/T10RANGE,OUTPUT,RATED RATED OUTPUT RANGE THE MINIMUM TO MAXIMUM OUTPUT AT WHICH THE ITEM IS RATED. 1D AND 1F MODE REPLY12AG67 CJDZA 12QUANTITY,BLOWER BLOWER QUANTITY THE NUMBER OF BLOWERS PROVIDED. 1A MODE REPLY 0 CJFBD /D/ 07OUTLET,ROTATABLE,BLOWER BLOWER ROTATABLE OUTLET AN INDICATION OF WHETHER OR NOT A BLOWER ROTATABLE OUTLET IS INCLUDED. SELECT REPLY CODE 10AA49 CJFCA /D/ 12QUANTITY DUSTED SIMULTANEOUS,ROW ROW QUANTITY DUSTED SIMULTANEOUS THE NUMBER OF ROWS THAT CAN BE DUSTED AT ONE TIME. 1A MODE REPLY 0 CJFDD /D/ 09MATERIAL,HOPPER HOPPER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HOPPER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CJFFD /D/ 07REMOVABILITY,CONTAINER CONTAINER REMOVABILITY AN INDICATION OF WHETHER OR NOT THE CONTAINER IS REMOVABLE. SELECT REPLY CODE 10AB00 CJFGJ /D/ 04DIAMETER,MAXIMUM,PUMP PUMP MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PUMP,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CJFHJ /D/ 04LENGTH,PUMP PUMP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE PUMP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CJFJD /D/ 07ADJUSTABILITY,PATTERN,DUST DUST PATTERN ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE DUST PATTERN IS ADJUSTABLE. SELECT REPLY CODE 10AB00 CJFKD /D/ 19PATTERN,DUSTING DUSTING PATTERN AN INDICATION OF THE PATTERN PRODUCED BY DUSTING. SELECT REPLY CODE 10AK54 CJFLD /D/ 07PEDAL,HOLDING,FOOT FOOT HOLDING PEDAL AN INDICATION OF WHETHER OR NOT A FOOT HOLDING PEDAL IS INCLUDED. SELECT REPLY CODE 10AA49 CJFMD /D/ 07CLUTCH,PROPULSION PROPULSION CLUTCH AN INDICATION OF WHETHER OR NOT A PROPULSION CLUTCH IS INCLUDED. SELECT REPLY CODE 10AA49 CJFND 05DIRECTION,DRIVE,GEAR GEAR DRIVE DIRECTION THE DIRECTION IN WHICH THE DRIVE IS GEARED. SELECT REPLY CODE 10AA38 CJFPD 18TYPE,BAR,HANDLE HANDLE BAR TYPE INDICATES THE TYPE OF HANDLE BAR PROVIDED. SELECT REPLY CODE 10AC55 CJFQD 11METHOD,DRIVE,ATTACHMENT ATTACHMENT DRIVE METHOD THE MEANS BY WHICH THE ATTACHMENT(S) IS DRIVEN. SELECT REPLY CODE 10AL40 CJFRD 18TYPE,UNIT,CUTTING CUTTING UNIT TYPE INDICATES THE TYPE OF CUTTING UNIT. SELECT REPLY CODE 10AK95 CJFSJ T04HEIGHT RANGE,CUTTING CUTTING HEIGHT RANGE THE MINIMUM TO MAXIMUM CUTTING HEIGHT OF THE ITEM. 1D AND 1F MODE REPLY11AA05 CJFTA 12QUANTITY,UNIT,CUTTING CUTTING UNIT QUANTITY THE NUMBER OF CUTTING UNITS PROVIDED. 1A MODE REPLY 0 CJFWJ 04WIDTH,UNIT,CUTTING CUTTING UNIT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CUTTING UNIT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CJFXD 19ACCOMMODATION,OPERATOR OPERATOR ACCOMMODATION THE ACCOMMODATION PROVIDED FOR THE OPERATOR. SELECT REPLY CODE 10AK54 CJFYD /D/ 07TREAD,RUBBER,ROLLER ROLLER RUBBER TREAD AN INDICATION OF WHETHER OR NOT RUBBER TREAD IS INCLUDED ON THE ROLLER(S). SELECT REPLY CODE 10AA49 CJFZD /D/ 07TREAD,RUBBER,CASTER CASTER RUBBER TREAD AN INDICATION OF WHETHER OR NOT RUBBER TREAD IS INCLUDED ON THE CASTER(S). SELECT REPLY CODE 10AA49 CJGBD /D/ 07TRANSMISSION,SPEED,MULTIPLE MULTIPLE SPEED TRANSMISSION AN INDICATION OF WHETHER OR NOT A MULTIPLE SPEED TRANSMISSION IS INCLUDED. SELECT REPLY CODE 10AA49 CJGCJ 04WIDTH,CUTTING,OVERALL OVERALL CUTTING WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CUTTING AREA OF AN ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CJGDD 11METHOD,MOVING MOVING METHOD THE MEANS BY WHICH THE ITEM IS MOVED. SELECT REPLY CODE 10AD28 CJGFD 19SOURCE,POWER,CUTTING UNIT CUTTING UNIT POWER SOURCE THE SOURCE OF POWER OF THE CUTTING UNIT. SELECT REPLY CODE 10AG27 CJGGD /D/ 07FEATURE,WHEEL,RETRACTABLE RETRACTABLE WHEEL FEATURE AN INDICATION OF WHETHER OR NOT A RETRACTABLE WHEEL/S/ FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CJGHD 11METHOD,RAISING,CUTTING UNIT CUTTING UNIT RAISING METHOD THE MEANS USED TO RAISE THE CUTTING UNIT. SELECT REPLY CODE 10AH20 CJGJG 04ANGLE RANGE,CUTTING CUTTING ANGLE RANGE THE VARIATION OF THE CUTTING ANGLE OF THE ITEM. FULL TEXT WRITE-IN 0 CJGKD /D/ 08LOCATION FOR WHICH DESIGNED,CONNECTION CONNECTION LOCATION FOR WHICH DESIGNED INDICATES THE LOCATION FOR WHICH THE ITEM IS DESIGNED TO BE CONNECTED. PLEASE USE MRC BGRY IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AJ91 CJGLD /D/ 19DEGREE,ADJUSTMENT ADJUSTMENT DEGREE THE DEGREE OF ADJUSTMENT OF THE ITEM. SELECT REPLY CODE 10AC58 CJGMG 10AREA,SPRAY,MAXIMUM MAXIMUM SPRAY AREA THE MAXIMUM AREA THE ITEM WILL SPRAY. FULL TEXT WRITE-IN 0 CJGNJ 04DIAMETER,DRUM,LOAD LOAD DRUM DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR LOAD DRUM,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJGPJ 04LENGTH,DRUM,LOAD LOAD DRUM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE LOAD DRUM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CJGQG /D/ 04LENGTH AND SIZE ACCOMMODATED,CABLE,LOAD DRUM LOAD DRUM CABLE LENGTH AND SIZE ACCOMMODATED THE LENGTH OF A CABLE OF A GIVEN SIZE THAT THE LOAD DRUM WILL ACCOMMODATE. FULL TEXT WRITE-IN 0 CJGRD /D/ 09MATERIAL,OUTER OUTER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE OUTER MATERIAL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CJGSJ T04LENGTH,ADJUSTABLE,CLOSED CLOSED ADJUSTABLE LENGTH A MEASUREMENT OF THE MINIMUM TO MAXIMUM ADJUSTABLE LENGTH OF THE ITEM WHEN CLOSED. 1D AND 1F MODE REPLY11AA05 CJGTJ 04WIDTH,CLOSED CLOSED WIDTH A MEASUREMENT OF THE WIDTH OF THE ITEM WHEN IN A CLOSED POSITION. 2D AND 1B MODE REPLY21AA051AC20 CJGWJ T04DEPTH,ADJUSTABLE,CLOSED CLOSED ADJUSTABLE DEPTH A MEASUREMENT OF THE MINIMUM TO MAXIMUM ADJUSTABLE DEPTH OF THE ITEM WHEN CLOSED. 1D AND 1F MODE REPLY11AA05 CJGXD /D/ 07DEVICE,RELEASE,QUICK QUICK RELEASE DEVICE AN INDICATION OF WHETHER OR NOT A QUICK RELEASE DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 CJGYJ 04LENGTH ACCOMMODATED,OVERALL,AX HEAD AX HEAD OVERALL LENGTH ACCOMMODATED THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ACCOMMODATED AX HEAD. 1D AND 1B MODE REPLY11AA05 CJGZJ 04WIDTH ACCOMMODATED,BLADE BLADE WIDTH ACCOMMODATED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BLADE ACCOMMODATED,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CJHBJ 04WIDTH ACCOMMODATED,OVERALL,AX HEAD AX HEAD OVERALL WIDTH ACCOMMODATED AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE AX HEAD ACCOMMODATED,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CJHCJ 04THICKNESS ACCOMMODATED,OVERALL,AX HEAD AX HEAD OVERALL THICKNESS ACCOMMODATED AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF THE AX HEAD ACCOMMODATED,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 CJHDJ 04LENGTH ACCOMMODATED,BLADE BLADE LENGTH ACCOMMODATED A MEASUREMENT OF THE LONGEST DIMENSION OF THE BLADE ACCOMMODATED,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CJHFD /D/ 09MATERIAL,BINDING BINDING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BINDING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CJHGD /D/ 07CORD,TIE TIE CORD AN INDICATION OF WHETHER OR NOT A TIE CORD IS PROVIDED. SELECT REPLY CODE 10AB22 CJHHD /D/ 07STRAP/LINE,LOWERING LOWERING STRAP/LINE AN INDICATION OF WHETHER OR NOT A LOWERING STRAP AND/OR LINE IS PROVIDED. SELECT REPLY CODE 10AB22 CJHJG 19AGENCY,CONTROLLING,DETAILED DESIGN IDENTIFICATION DETAILED DESIGN IDENTIFICATION CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DETAILED DESIGN IDENTIFICATION OF THE ITEM. FULL TEXT WRITE-IN 0 CJHKD /D/ 09MATERIAL,EPAULET EPAULET MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE EPAULET IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CJHLD /D/ 19CONDITION,SURFACE,BODY BODY SURFACE CONDITION THE CONDITION OF THE BODY WITH RESPECT TO THE TEXTURE OF THE SURFACE. SELECT REPLY CODE 10AK39 CJHMD /D/ 19CONDITION,SURFACE,CAP CAP SURFACE CONDITION THE CONDITION OF THE CAP WITH RESPECT TO THE TEXTURE OF THE SURFACE. SELECT REPLY CODE 10AK39 CJHND /D/ 19CONDITION,SURFACE,EPAULET EPAULET SURFACE CONDITION THE CONDITION OF THE EPAULET WITH RESPECT TO THE TEXTURE OF THE SURFACE. SELECT REPLY CODE 10AK39 CJHPD /D/ 07EPAULET,REINFORCED,STEEL SPRING STEEL SPRING REINFORCED EPAULET AN INDICATION OF WHETHER OR NOT A STEEL SPRING REINFORCED EPAULET/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CJHQD /D/ 07FLAP,HIP HIP FLAP AN INDICATION OF WHETHER OR NOT A HIP FLAP/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CJHRD /D/ 07FEATURE W/ONE SIDE WHITE,REVERSIBLE,MATERIAL MATERIAL REVERSIBLE FEATURE W/ONE SIDE WHITE AN INDICATION OF WHETHER OR NOT A REVERSIBLE MATERIAL FEATURE WITH ONE SIDE WHITE IS INCLUDED. SELECT REPLY CODE 10AA49 CJHSJ /D/ 09MATERIAL AND PERCENTAGE,FILLING FILLING MATERIAL AND PERCENTAGE THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FILLING IS FABRICATED AND THE PERCENTAGE. 1D AND 1B MODE REPLY16AD09 CJHTD /D/ 07BAG,CARRYING CARRYING BAG AN INDICATION OF WHETHER OR NOT A CARRYING BAG IS INCLUDED. SELECT REPLY CODE 10AA49 CJHWA 19IDENTIFICATION,SHADE,BAG BAG SHADE IDENTIFICATION THE DESIGNATION ASSIGNED TO A PARTICULAR GRADATION OF A BAG COLOR FOR THE PURPOSE OF READY IDENTIFICATION. 1A MODE REPLY 0 CJHXD 19SOURCE,SHADE,BAG BAG SHADE SOURCE THE NAME OF THE REFERENCE SOURCE OF THE BAG SHADE IDENTIFICATION DESIGNATOR. SELECT REPLY CODE 10AF94 CJHYD /D/ 07MATTRESS,SEPARATE SEPARATE MATTRESS AN INDICATION OF WHETHER OR NOT A SEPARATE MATTRESS IS INCLUDED. SELECT REPLY CODE 10AA49 CJHZD /D/ 09MATERIAL,CASING,MATTRESS MATTRESS CASING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MATTRESS CASING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CJJBD /D/ 09MATERIAL,FILLING,MATTRESS MATTRESS FILLING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MATTRESS FILLING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CJJCJ 10FREQUENCY,FACTOR,QUALITY QUALITY FACTOR FREQUENCY THE FREQUENCY AT WHICH THE QUALITY FACTOR IS DETERMINED. 1D AND 1B MODE REPLY11AC32 CJJDA 19FACTOR,QUALITY,NUMERIC NUMERIC QUALITY FACTOR AN INDICATION OF THE NUMERIC QUALITY FACTOR OF AN ITEM. 1A MODE REPLY 0 CJJFD /D/ 07FEATURE FOR INSERTION IN AIRCRAFT EJECTION SEAT COVER,FOLDED/TUFTED FOLDED/TUFTED FEATURE FOR INSERTION IN AIRCRAFT EJECTION SEAT COVER AN INDICATION OF WHETHER OR NOT A FOLDED AND/OR TUFTED FEATURE FOR INSERTION IN AIRCRAFT EJECTION SEAT COVER IS INCLUDED. SELECT REPLY CODE 10AA49 CJJGD /D/ 11METHOD,FOLDING/TUFTING FOLDING/TUFTING METHOD THE MEANS USED IN FOLDING AND/OR TUFTING THE ITEM. SELECT REPLY CODE 10AM88 CJJHD /D/ 07COVER,CUSHION CUSHION COVER AN INDICATION OF WHETHER OR NOT A CUSHION COVER IS INCLUDED. SELECT REPLY CODE 10AA49 CJJJD /D/ 02DESIGN,COVER COVER DESIGN THE DESIGN OF THE COVER. SELECT REPLY CODE 10AH21 CJJKD /D/ 07TAG,ATTACHED ATTACHED TAG AN INDICATION OF WHETHER OR NOT AN ATTACHED TAG/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CJJLG /D/ 19MARKINGS,TAG TAG MARKINGS AN INDICATION OF THE MARKINGS ON THE TAG. FULL TEXT WRITE-IN 0 CJJMJ T10RANGE PER INDICATOR,MEASUREMENT MEASUREMENT RANGE PER INDICATOR THE MINIMUM TO MAXIMUM VALUE EACH INDICATOR IS CAPABLE OF MEASURING. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 2D AND 1F MODE REPLY22AJ203AJ91 CJJND 19SOURCE,POWER,PUMPING UNIT PUMPING UNIT POWER SOURCE THE SOURCE OF POWER WHICH DRIVES THE PUMPING UNIT. SELECT REPLY CODE 10AG27 CJJPD /D/ 07SUPPLY,POWER,PNEUMATIC PNEUMATIC POWER SUPPLY AN INDICATION OF WHETHER OR NOT A PNEUMATIC POWER SUPPLY IS INCLUDED. SELECT REPLY CODE 10AA49 CJJQG 10OUTPUT RATING IN CFM AT PSI OUTPUT RATING IN CFM AT PSI THE RATED CAPACITY OF THE AIR OUTPUT DELIVERED BY THE ITEM,EXPRESSED IN CUBIC FEET PER MINUTE AT POUNDS PER SQUARE INCH. FULL TEXT WRITE-IN 0 CJJRD 19SOURCE,POWER,PNEUMATIC PNEUMATIC POWER SOURCE THE SOURCE OF POWER WHICH SUPPLIES THE AIR. SELECT REPLY CODE 10AG27 CJJSJ 10PULL,DRAWBAR DRAWBAR PULL THE PULL LIMIT/S/ FOR WHICH THE DRAWBAR IS DESIGNED. 2D AND 1B MODE REPLY22AG671AC20 CJJTB /D/ 10CAPACITY RATING IN CFM,DISPLACEMENT,AIR AIR DISPLACEMENT CAPACITY RATING IN CFM THE RATED CAPACITY OF THE AIR VOLUME DISPLACED THROUGH THE ITEM,EXPRESSED IN CUBIC FEET PER MINUTE. 1B MODE REPLY 0 CJJWG 10HORSEPOWER AT SPECIFIED RPM,BRAKE,ENGINE ENGINE BRAKE HORSEPOWER AT SPECIFIED RPM THE POWER DELIVERED BY THE ENGINE AT SPECIFIED REVOLUTIONS PER MINUTE. FULL TEXT WRITE-IN 0 CJJXJ 10PULL,DRAWBAR,MINIMUM MINIMUM DRAWBAR PULL THE MINIMUM PULL FOR WHICH THE DRAWBAR IS DESIGNED. 1D AND 1B MODE REPLY12AG67 CJJYD /D/ 07FEATURE,SPARKPROOF,ENGINE ENGINE SPARKPROOF FEATURE AN INDICATION OF WHETHER OR NOT AN ENGINE SPARKPROOF FEATURE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CJJZJ 10PULL,DRAWBAR,MAXIMUM MAXIMUM DRAWBAR PULL THE MAXIMUM PULL FOR WHICH THE DRAWBAR IS DESIGNED. 1D AND 1B MODE REPLY12AG67 CJKBJ 10PULL,DRAWBAR,MINIMUM ACCEPTABLE MINIMUM ACCEPTABLE DRAWBAR PULL THE MINIMUM ACCEPTABLE PULL FOR WHICH THE DRAWBAR IS DESIGNED. 1D AND 1B MODE REPLY12AG67 CJKCG 03DESIGNATION,SIZE,TIRE,REAR WHEEL REAR WHEEL TIRE SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE REAR WHEEL TIRE IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. FULL TEXT WRITE-IN 0 CJKDD 11METHOD,OPERATION,COUPLER COUPLER OPERATION METHOD THE MEANS BY WHICH THE COUPLER IS OPERATED. SELECT REPLY CODE 10AH98 CJKFG 03DESIGNATION,SIZE,TIRE,FRONT WHEEL FRONT WHEEL TIRE SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE FRONT WHEEL TIRE IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. FULL TEXT WRITE-IN 0 CJKGD /D/ 07COMPARTMENT,AMMUNITION AMMUNITION COMPARTMENT AN INDICATION OF WHETHER OR NOT AN AMMUNITION COMPARTMENT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CJKHD 18TYPE,CARRIER,CARGO CARGO CARRIER TYPE INDICATES THE TYPE OF CARGO CARRIER PROVIDED. SELECT REPLY CODE 10AK54 CJKJD 11METHOD,DRIVE,TRANSMISSION TRANSMISSION DRIVE METHOD THE MEANS USED TO DRIVE THE TRANSMISSION. SELECT REPLY CODE 10AJ53 CJKKD /D/ 07COMPRESSOR,AIR AIR COMPRESSOR AN INDICATION OF WHETHER OR NOT AN AIR COMPRESSOR(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CJKLD /D/ 07GENERATOR,AUXILIARY AUXILIARY GENERATOR AN INDICATION OF WHETHER OR NOT AN AUXILIARY GENERATOR IS INCLUDED. SELECT REPLY CODE 10AA49 CJKMD /D/ 07PUMP,HYDRAULIC,DOZER ACCOMMODATED DOZER ACCOMMODATED HYDRAULIC PUMP AN INDICATION OF WHETHER OR NOT A DOZER ACCOMMODATED HYDRAULIC PUMP(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CJKNB 10VOLTAGE RATING,SYSTEM,ELECTRICAL ELECTRICAL SYSTEM VOLTAGE RATING THE RATED VOLTAGE OF THE ELECTRICAL SYSTEM FOR WHICH THE ITEM IS DESIGNED. 1B MODE REPLY 0 CJKPD 08LOCATION,ATTACHMENT,TOWING TOWING ATTACHMENT LOCATION INDICATES THE LOCATION OF THE TOWING ATTACHMENT(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 CJKQD 08LOCATION,MOUNTING,ENGINE ENGINE MOUNTING LOCATION INDICATES THE MOUNTING LOCATION OF THE ENGINE. SELECT REPLY CODE 10AJ91 CJKRJ 04WIDTH,TRACK TRACK WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE TRACK LENGTH ON THE GROUND,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CJKSD 19SYSTEM,POWER,ACCOMMODATED TOWED VEHICLE ACCOMMODATED TOWED VEHICLE POWER SYSTEM AN INDICATION OF THE POWER SYSTEM PROVIDED TO ACCOMMODATE A TOWED VEHICLE. SELECT REPLY CODE 10AG27 CJKTG 10TORQUE RATING AT SPECIFIED RPM,ENGINE ENGINE TORQUE RATING AT SPECIFIED RPM THE RATED TURNING FORCE,IN FOOT POUNDS,DELIVERED BY THE ENGINE AT SPECIFIED REVOLUTIONS PER MINUTE. FULL TEXT WRITE-IN 0 CJKWJ 10GAGE,TRACK,VEHICLE VEHICLE TRACK GAGE A MEASUREMENT OF THE CENTER TO CENTER DISTANCE BETWEEN THE DRIVE SPROCKETS OF THE VEHICLE. 1D AND 1B MODE REPLY11AA05 CJKXD 18TYPE,TRACK TRACK TYPE INDICATES THE TYPE OF TRACK PROVIDED. SELECT REPLY CODE 10AK54 CJKYD 18TYPE,SHOE,TRACK TRACK SHOE TYPE INDICATES THE TYPE OF SHOE PROVIDED ON THE TRACK. SELECT REPLY CODE 10AK54 CJKZD 18TYPE,GROUSER GROUSER TYPE INDICATES THE TYPE OF GROUSER PROVIDED. SELECT REPLY CODE 10AK54 CJLBA 12QUANTITY,RANGE,TRANSFER SPEED TRANSFER SPEED RANGE QUANTITY THE NUMBER OF TRANSFER SPEED RANGES PROVIDED. 1A MODE REPLY 0 CJLCD /D/ 07PLATE,ETCHED,DIOPTRIC VALUE DIOPTRIC VALUE ETCHED PLATE AN INDICATION OF WHETHER OR NOT A DIOPTRIC VALUE ETCHED PLATE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CJLDD /D/ 07SCALE,PLUS/MINUS PLUS/MINUS SCALE AN INDICATION OF WHETHER OR NOT A PLUS AND MINUS SCALE IS INCLUDED. SELECT REPLY CODE 10AA49 CJLFD 18TYPE,DISPLACEMENT,IMAGE IMAGE DISPLACEMENT TYPE INDICATES THE TYPE OF IMAGE DISPLACEMENT. SELECT REPLY CODE 10AK95 CJLGD /D/ 07MOUNTING,PLATE,CENTER/BACK CENTER/BACK PLATE MOUNTING AN INDICATION OF WHETHER OR NOT A CENTER AND BACK PLATE MOUNTING/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CJLHJ /D/ 04DIAMETER,PLATE,BACK BACK PLATE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR BACK PLATE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CJLJJ /D/ 04THICKNESS,FLANGE,BACK PLATE BACK PLATE FLANGE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A BACK PLATE FLANGE,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 CJLKA 12QUANTITY,APERTURE APERTURE QUANTITY THE NUMBER OF APERTURES INCLUDED. 1A MODE REPLY 0 CJLLD 08LOCATION,MARKING,SCALE SCALE MARKING LOCATION INDICATES THE LOCATION OF THE SCALE MARKINGS ON THE ITEM. SELECT REPLY CODE 10AJ91 CJLMF T10RANGE,SCALE,CIRCULAR,RIGHT RIGHT CIRCULAR SCALE RANGE THE MINIMUM AND MAXIMUM LIMITS OF THE RIGHT CIRCULAR SCALE. 1F MODE REPLY 0 CJLND /D/ 07KEEPER,STRIKE STRIKE KEEPER AN INDICATION OF WHETHER OR NOT A STRIKE KEEPER IS FURNISHED. SELECT REPLY CODE 10AA55 CJLPD 18TYPE,KEEPER,STRIKE STRIKE KEEPER TYPE INDICATES THE TYPE OF STRIKE KEEPER PROVIDED. SELECT REPLY CODE 10AK54 CJLQD /D/ 07ESCUTCHEON ESCUTCHEON AN INDICATION OF WHETHER OR NOT AN ESCUTCHEON IS FURNISHED. SELECT REPLY CODE 10AA55 CJLRA 12QUANTITY,CHANGE,KEY KEY CHANGE QUANTITY THE NUMBER OF KEY CHANGES PROVIDED. 1A MODE REPLY 0 CJLSD /D/ 07PROVISION,KEY,MASTER MASTER KEY PROVISION AN INDICATION OF WHETHER OR NOT A MASTER KEY PROVISION IS INCLUDED. SELECT REPLY CODE 10AA49 CJLTA /D/ 12QUANTITY,SETTING,DIAL DIAL SETTING QUANTITY THE NUMBER OF DIAL SETTINGS PROVIDED. 1A MODE REPLY 0 CJLWD /D/ 19HARDWARE,MOUNTING,FURNISHED FURNISHED MOUNTING HARDWARE AN INDICATION OF THE MOUNTING HARDWARE FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AE36 CJLXD 18TYPE,BOX BOX TYPE INDICATES THE TYPE OF BOX PROVIDED. SELECT REPLY CODE 10AK95 CJLYJ /D/ 04THICKNESS FOR WHICH DESIGNED,MAXIMUM,DOOR/GATE DOOR/GATE MAXIMUM THICKNESS FOR WHICH DESIGNED A MEASUREMENT OF THE MAXIMUM THICKNESS OF THE DOOR AND/OR GATE FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AA05 CJLZA 12QUANTITY,HANDLE,GRIP GRIP HANDLE QUANTITY THE NUMBER OF GRIP HANDLES PROVIDED. 1A MODE REPLY 0 CJMBJ /D/ 04LENGTH,OVERALL,GRIP HANDLE GRIP HANDLE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE GRIP HANDLE. 2D AND 1B MODE REPLY21AA051AC20 CJMCD /D/ 07PLATE,HANDLE,GRIP GRIP HANDLE PLATE AN INDICATION OF WHETHER OR NOT A GRIP HANDLE PLATE IS PROVIDED. SELECT REPLY CODE 10AB22 CJMDJ /D/ 04HEIGHT,PLATE PLATE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE PLATE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CJMFJ 04LENGTH,OVERALL,LATCH BAR LATCH BAR OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE LATCH BAR. 2D AND 1B MODE REPLY21AA051AC20 CJMGA /D/ 16STYLE,CATCH CATCH STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CATCH. 1A MODE REPLY 0 CJMHJ 04WIDTH,SURFACE,ENGAGING ENGAGING SURFACE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CJMJJ 04DIAMETER,SURFACE,ENGAGING ENGAGING SURFACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CJMKJ /D/ 04RADIUS,SURFACE,ENGAGING ENGAGING SURFACE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CJMLJ 04THICKNESS,SURFACE,ENGAGING ENGAGING SURFACE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CJMMJ 04WIDTH,CATCH CATCH WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CJMNJ 04WIDTH,NUT,WING WING NUT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CJMPJ 04WIDTH,SPRING,EXTENDED TENSION EXTENDED TENSION SPRING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CJMQD /D/ 07EYE,PADLOCK PADLOCK EYE AN INDICATION OF WHETHER OR NOT A PADLOCK EYE IS INCLUDED. SELECT REPLY CODE 10AA49 CJMRJ /D/ 10CAPACITY,MAXIMUM,PULL DOWN PULL DOWN MAXIMUM CAPACITY A MEASUREMENT OF THE MAXIMUM PULL DOWN CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 CJMSJ 10CAPACITY,MAXIMUM,LOAD CARRYING LOAD CARRYING MAXIMUM CAPACITY A MEASUREMENT OF THE MAXIMUM LOAD CARRYING CAPACITY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 CJMTD /D/ 09MATERIAL,BODY/ELEMENT BODY/ELEMENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BODY/ELEMENT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CJMWD /D/ 17SURFACE TREATMENT,BODY/ELEMENT BODY/ELEMENT SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE BODY/ELEMENT SURFACE. SELECT REPLY CODE 10AD09 CJMXA /D/ 16STYLE,STRIKE,CATCH CATCH STRIKE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CATCH STRIKE. 1A MODE REPLY 0 CJMYA 12QUANTITY,HOLE,FIRST SURFACE FIRST SURFACE HOLE QUANTITY NONE. 1A MODE REPLY 0 CJMZA 12QUANTITY,HOLE,SECOND SURFACE SECOND SURFACE HOLE QUANTITY NONE. 1A MODE REPLY 0 CJNBG /D/ 04SIZE,HOLE,FIRST SURFACE FIRST SURFACE HOLE SIZE NONE. FULL TEXT WRITE-IN 0 CJNCG /D/ 04SIZE,HOLE,SECOND SURFACE SECOND SURFACE HOLE SIZE NONE. FULL TEXT WRITE-IN 0 CJNDJ /D/ 04WIDTH,TONGUE,MOUNTING MOUNTING TONGUE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CJNFD /D/ 14SHAPE,PIN PIN SHAPE THE PHYSICAL CONFIGURATION OF THE PIN. SELECT REPLY CODE 10AD07 CJNGJ 10PRESSURE RATING,END END PRESSURE RATING THE PRESSURE AT WHICH THE END IS DESIGNED TO OPERATE. 2D AND 1B MODE REPLY22AG671AC20 CJNHD /D/ 18TYPE,PULLEY PULLEY TYPE INDICATES THE TYPE OF PULLEY PROVIDED. SELECT REPLY CODE 10AK54 CJNJJ /D/ 04HEIGHT,HOOK HOOK HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CJNKD /D/ 07STOP,SHOULDER SHOULDER STOP AN INDICATION OF WHETHER OR NOT A SHOULDER STOP IS INCLUDED. SELECT REPLY CODE 10AA49 CJNLD /D/ 07SHIELD,EXPANSION EXPANSION SHIELD AN INDICATION OF WHETHER OR NOT AN EXPANSION SHIELD/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 CJNMJ /D/ 04LENGTH,HOOK HOOK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE HOOK,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CJNND /D/ 07FEATURE,STYLE,OFFSET OFFSET STYLE FEATURE AN INDICATION OF WHETHER OR NOT AN OFFSET STYLE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CJNPJ 04DISTANCE BETWEEN DISKS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN DISKS THE CENTER TO CENTER DISTANCE BETWEEN THE DISKS. 2D AND 1B MODE REPLY21AA051AC20 CJNQD 14SHAPE,EDGE,CUTTING CUTTING EDGE SHAPE THE PHYSCIAL CONFIGURATION OF THE CUTTING EDGE. SELECT REPLY CODE 10AD07 CJNRD /D/ 07SNATH SNATH AN INDICATION OF WHETHER OR NOT A SNATH IS INCLUDED. SELECT REPLY CODE 10AA49 CJNSJ 04LENGTH,TINE TINE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TINE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CJNWD 18TYPE,AGENT,MEDICATED MEDICATED AGENT TYPE INDICATES THE TYPE OF MEDICATED AGENT ADDED. SELECT REPLY CODE 10AG62 CJNXD 18TYPE FOR WHICH DESIGNED,BLADE BLADE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF BLADE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AJ46 CJNYD /D/ 07FEATURE,TYPE,INJECTOR INJECTOR TYPE FEATURE AN INDICATION OF WHETHER OR NOT AN INJECTOR TYPE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CJNZJ 04LENGTH,PART,EXPOSED BRUSH EXPOSED BRUSH PART LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE EXPOSED BRUSH PART,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CJPBD /D/ 07REPELLENT,INSECT INSECT REPELLENT AN INDICATION OF WHETHER OR NOT AN INSECT REPELLENT IS INCLUDED. SELECT REPLY CODE 10AA49 CJPCD 19CLIMATE FOR WHICH DESIGNED CLIMATE FOR WHICH DESIGNED INDICATES THE CLIMATE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 CJPDD /D/ 07FEATURE,GROUND,HOLLOW HOLLOW GROUND FEATURE AN INDICATION OF WHETHER OR NOT A HOLLOW GROUND FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CJPGD /D/ 07DESIGNED FOR CLEANING NAILS,POINT POINT DESIGNED FOR CLEANING NAILS AN INDICATION OF WHETHER OR NOT A POINT DESIGNED FOR CLEANING NAILS IS PROVIDED. SELECT REPLY CODE 10AB22 CJPHG /D/ 19AGENCY,CONTROLLING,DESIGN DESIGNATION DESIGN DESIGNATION CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY,COMMERCIAL ORGANIZATION,OR MANUFACTURER CONTROLLING THE DESIGN DESIGNATION. FULL TEXT WRITE-IN 0 CJPJG /D/ 19AGENCY,CONTROLLING,SHADE/COLOR PATTERN DESIGNATION SHADE/COLOR PATTERN DESIGNATION CONTROLLING AGENCY THE NAME OF THE GOVERNMENT AGENCY,COMMERCIAL ORGANIZATION OR MANUFACTURER CONTROLLING THE SHADE AND/OR COLOR PATTERN DESIGNATION. FULL TEXT WRITE-IN 0 CJPKD /D/ 07FEATURE,REMOVAL W/WATER REMOVAL W/WATER FEATURE AN INDICATION OF WHETHER OR NOT A REMOVAL WITH WATER FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CJPLD 19RIGIDITY,BRISTLE BRISTLE RIGIDITY THE RELATIVE RIGIDITY OF THE BRISTLE. SELECT REPLY CODE 10AN25 CJPMA 12QUANTITY,TUFT TUFT QUANTITY THE NUMBER OF TUFTS PROVIDED. 1A MODE REPLY 0 CJPND 18TYPE FOR WHICH DESIGNED,RAZOR RAZOR TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF RAZOR FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AJ46 CJPPA 12QUANTITY PER UNIT,PLY PLY QUANTITY PER UNIT THE NUMBER OF PLIES PER UNIT. 1A MODE REPLY 0 CJPQD 18TYPE,OPERATION,HAND HAND OPERATION TYPE INDICATES THE TYPE OF HAND OPERATION PROVIDED. SELECT REPLY CODE 10AK54 CJPRD /D/ 07PLUG,ADAPTER ADAPTER PLUG AN INDICATION OF WHETHER OR NOT AN ADAPTER PLUG IS INCLUDED. SELECT REPLY CODE 10AA49 CJPSF /D/T10RANGE IN VOLTS,VOLTAGE VOLTAGE RANGE IN VOLTS THE MINIMUM TO MAXIMUM VOLTAGE,EXPRESSED IN VOLTS. 1F MODE REPLY 0 CJPTD /D/ 07CASE,TRAVEL TRAVEL CASE AN INDICATION OF WHETHER OR NOT A TRAVEL CASE IS PROVIDED. SELECT REPLY CODE 10AB22 CJPWD 19SPECIES,WOOD,STILE STILE WOOD SPECIES THE BOTANICAL VARIETY TO WHICH THE STILE WOOD BELONGS. SELECT REPLY CODE 10AM00 CJPXD 19SPECIES,WOOD,RAIL RAIL WOOD SPECIES THE BOTANICAL VARIETY TO WHICH THE RAIL WOOD BELONGS. SELECT REPLY CODE 10AM00 CJPYD 19SPECIES,WOOD,PANEL PANEL WOOD SPECIES THE BOTANICAL VARIETY TO WHICH THE PANEL WOOD BELONGS. SELECT REPLY CODE 10AM00 CJPZG 02DESIGN AND LOCATION,PANEL PANEL DESIGN AND LOCATION THE DESIGN OF THE PANEL AND THE LOCATION. FULL TEXT WRITE-IN 0 CJQBG /D/ 18TYPE AND LOCATION,MOLDING,INCLOSING PANEL INCLOSING PANEL MOLDING TYPE AND LOCATION INDICATES THE TYPE OF MOLDING FOR INCLOSING THE PANEL AND THE LOCATION. FULL TEXT WRITE-IN 0 CJQCG 19ARRANGEMENT,PANEL PANEL ARRANGEMENT AN INDICATION OF THE ARRANGEMENT OF THE PANEL(S). FULL TEXT WRITE-IN 0 CJQDD /D/ 07RAIL,DIAGONAL DIAGONAL RAIL AN INDICATION OF WHETHER OR NOT A DIAGONAL RAIL IS INCLUDED. SELECT REPLY CODE 10AA49 CJQFD 19SPECIES,WOOD,CORE CORE WOOD SPECIES THE BOTANICAL VARIETY TO WHICH THE CORE WOOD BELONGS. SELECT REPLY CODE 10AM00 CJQGH /D/ 19SPECIES AND LOCATION,WOOD,FACE FACE WOOD SPECIES AND LOCATION THE BOTANICAL VARIETY TO WHICH THE FACE WOOD BELONGS AND THE LOCATION. 2D MODE REPLY 22AM003AJ91 CJQHD /D/ 02DESIGN,EDGE,MATING,PAIRED DOORS PAIRED DOORS MATING EDGE DESIGN THE DESIGN OF THE MATING EDGE OF THE PAIRED DOORS. SELECT REPLY CODE 10AL25 CJQJJ 04WIDTH,RAIL,TOP TOP RAIL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TOP RAIL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CJQKJ 04WIDTH,RAIL,BOTTOM BOTTOM RAIL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BOTTOM RAIL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CJQLJ 04WIDTH,RAIL,LOCK LOCK RAIL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE LOCK RAIL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CJQMA 12QUANTITY,RAIL,INTERMEDIATE INTERMEDIATE RAIL QUANTITY THE NUMBER OF INTERMEDIATE RAILS PROVIDED. 1A MODE REPLY 0 CJQNJ 04WIDTH,INSIDE,CONNECTION CONNECTION INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CJQPJ 04LENGTH,INSIDE,CONNECTION CONNECTION INSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CJQQD /D/ 07ATTACHED TO HOOK EYE END,SCREW,EYE EYE SCREW ATTACHED TO HOOK EYE END AN INDICATION OF WHETHER OR NOT AN EYE SCREW ATTACHED TO EYE END OF HOOK IS INCLUDED. SELECT REPLY CODE 10AA49 CJQRJ 04DISTANCE TRANSVERSE TO STAPLE,PLATE PLATE DISTANCE TRANSVERSE TO STAPLE THE DISTANCE ALONG THE PLATE TRANSVERSE TO THE STAPLE. 2D AND 1B MODE REPLY21AA051AC20 CJQSJ 04DISTANCE PARALLEL TO STAPLE,PLATE PLATE DISTANCE PARALLEL TO STAPLE THE DISTANCE ALONG THE PLATE PARALLEL TO THE STAPLE. 2D AND 1B MODE REPLY21AA051AC20 CJQTA 12QUANTITY,HOLE,PLATE MOUNTING PLATE MOUNTING HOLE QUANTITY THE NUMBER OF MOUNTING HOLES PROVIDED IN THE PLATE. 1A MODE REPLY 0 CJQWJ 04HEIGHT,STAPLE STAPLE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A STAPLE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CJQXJ 04WIDTH,STAPLE STAPLE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE STAPLE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CJQYJ 04DIAMETER,STOCK,STAPLE STAPLE STOCK DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE STAPLE STOCK,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CJQZJ 04THICKNESS,STOCK,STAPLE STAPLE STOCK THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE STAPLE STOCK,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 CJRBD /D/ 09MATERIAL,SCREW,HOLLOW HOLLOW SCREW MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HOLLOW SCREW IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CJRCD /D/ 17SURFACE TREATMENT,SCREW,HOLLOW HOLLOW SCREW SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A SURFACE OF A HOLLOW SCREW. SELECT REPLY CODE 10AD09 CJRDJ 10SIZE FOR WHICH DESIGNED,HOLE HOLE SIZE FOR WHICH DESIGNED DESIGNATES THE HOLE SIZE FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 CJRFJ T04THICKNESS RANGE FOR WHICH DESIGNED,MATERIAL MATERIAL THICKNESS RANGE FOR WHICH DESIGNED THE MINIMUM AND MAXIMUM THICKNESS OF THE MATERIAL FOR WHICH THE ITEM IS DESIGNED. 1D AND 1F MODE REPLY11AA05 CJRGD /D/ 07PROVISION,THREADED,ATTACHING SCREW ATTACHING SCREW THREADED PROVISION AN INDICATION OF WHETHER OR NOT A THREADED PROVISION FOR AN ATTACHING SCREW IS PROVIDED. SELECT REPLY CODE 10AB22 CJRHJ 04LENGTH FOR WHICH DESIGNED,MINIMUM,SCREW SCREW MINIMUM LENGTH FOR WHICH DESIGNED THE MINIMUM LENGTH OF THE SCREW FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AA05 CJRJD 18TYPE,SLEEVE SLEEVE TYPE INDICATES THE TYPE OF SLEEVE PROVIDED. SELECT REPLY CODE 10AK54 CJRKD 18TYPE,END,ENGAGING ENGAGING END TYPE INDICATES THE TYPE OF ENGAGING END PROVIDED. SELECT REPLY CODE 10AK54 CJRLJ /D/ 04LENGTH,FREE,EFFECTIVE EFFECTIVE FREE LENGTH A MEASUREMENT OF THE LONGEST EFFECTIVE FREE DIMENSION OF THE ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CJRMJ /D/ 04LENGTH,EXTENDED,EFFECTIVE EFFECTIVE EXTENDED LENGTH A MEASUREMENT OF THE LONGEST EFFECTIVE EXTENDED DIMENSION OF THE ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CJRND 19POSITION FOR WHICH DESIGNED,MOUNTING MOUNTING POSITION FOR WHICH DESIGNED AN INDICATION OF THE MOUNTING POSITION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AM84 CJRPD /D/ 07CATCH CATCH AN INDICATION OF WHETHER OR NOT A CATCH IS INCLUDED. SELECT REPLY CODE 10AA49 CJRQD /D/ 07HANDLE,INTEGRAL INTEGRAL HANDLE AN INDICATION OF WHETHER OR NOT AN INTEGRAL HANDLE IS INCLUDED. SELECT REPLY CODE 10AA49 CJRRD /D/ 07RING,LOCK,INTEGRAL INTEGRAL LOCK RING AN INDICATION OF WHETHER OR NOT AN INTEGRAL LOCK RING IS INCLUDED. SELECT REPLY CODE 10AA49 CJRSD 18TYPE,DEVICE,ANTIRATTLE ANTIRATTLE DEVICE TYPE INDICATES THE TYPE OF ANTIRATTLE DEVICE PROVIDED. SELECT REPLY CODE 10AK54 CJRTD 18TYPE,PAWL PAWL TYPE INDICATES THE TYPE OF PAWL PROVIDED. SELECT REPLY CODE 10AK54 CJRWD /D/ 07ADJUSTABILITY,PAWL PAWL ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE PAWL IS ADJUSTABLE. SELECT REPLY CODE 10AB00 CJRXD 11METHOD,ACTUATION,PAWL PAWL ACTUATION METHOD THE MEANS BY WHICH THE PAWL IS ACTUATED. SELECT REPLY CODE 10AC58 CJRYJ /D/ 04HEIGHT,PLATE,MOUNTING MOUNTING PLATE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CJRZJ /D/ 04LENGTH FROM ACTUATING SHAFT CENTER TO PAWL END,PAWL PAWL LENGTH FROM ACTUATING SHAFT CENTER TO PAWL END NONE. 2D AND 1B MODE REPLY21AA051AC20 CJSBB /D/ 10SWING IN DEG,PAWL PAWL SWING IN DEG NONE. 1B MODE REPLY 0 CJSCJ 04LENGTH,KNOB KNOB LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CJSDJ /D/ 04LENGTH,LOCK,KEY KEY LOCK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CJSFJ /D/ 04DIAMETER,LOCK,KEY KEY LOCK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CJSGJ 04DISTANCE,MOUNTING PLATE TO PAWL MOUNTING PLATE TO PAWL DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CJSHJ /D/ 04DIAMETER,SHAFT,ACTUATING ACTUATING SHAFT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CJSJJ 04DEPTH,CUP,RECESS RECESS CUP DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CJSKJ /D/ 04LENGTH FROM MOUNTING HOLE,HANDLE,GRIP GRIP HANDLE LENGTH FROM MOUNTING HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 CJSLJ 04WIDTH,HANDLE,GRIP GRIP HANDLE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CJSMJ 04DIAMETER,SHAFT,KNOB KNOB SHAFT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CJSNJ 04DIAMETER ACCOMMODATED,BALL BALL DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BALL WHICH THE ITEM WILL ACCOMMODATE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJSPJ 04DEPTH,GROOVE,RING RING GROOVE DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF A RING GROOVE,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CJSQJ 04LENGTH,OVERALL,CAP END CAP END OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CAP END. 2D AND 1B MODE REPLY21AA051AC20 CJSRJ 04DIAMETER,END,CAP CAP END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR CAP END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJSSJ 04DEPTH,SLOT,CAP END CAP END SLOT DEPTH THE MEASUREMENT BETWEEN SPECIFIED POINTS OF THE SLOT,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CJSTJ 04LENGTH,END,SPANNER SPANNER END LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SPANNER END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CJSWJ 04DIAMETER,END,SPANNER SPANNER END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR SPANNER END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJSXJ 04DISTANCE FROM PIN TO END DISTANCE FROM PIN TO END THE DISTANCE FROM THE PIN TO THE END OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CJSYJ /D/ 04DIAMETER,INSIDE,STEM STEM INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE STEM,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJSZA /D/ 12QUANTITY,HOLE,STEM AIR INTAKE STEM AIR INTAKE HOLE QUANTITY THE NUMBER OF STEM AIR INTAKE HOLES PROVIDED. 1A MODE REPLY 0 CJTBJ /D/ 04DIAMETER,HOLE,AIR INTAKE AIR INTAKE HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR AIR INTAKE HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJTCJ /D/ 04DISTANCE FROM AIR INTAKE HOLE TO BASE DISTANCE FROM AIR INTAKE HOLE TO BASE THE DISTANCE FROM THE AIR INTAKE HOLE TO THE BASE OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CJTDJ 04DIAMETER,OUTSIDE,FEED TUBE FEED TUBE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FEED TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJTFJ 04THICKNESS,WALL,FEED TUBE FEED TUBE WALL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE FEED TUBE WALL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CJTGD 18TYPE,HUB,FEED TUBE FEED TUBE HUB TYPE INDICATES THE TYPE OF FEED TUBE HUB PROVIDED. SELECT REPLY CODE 10AJ88 CJTHJ 04DIAMETER,OUTSIDE,VENT TUBE VENT TUBE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE VENT TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJTJJ 04THICKNESS,WALL,VENT TUBE VENT TUBE WALL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE VENT TUBE WALL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CJTKD 18TYPE,HUB,VENT TUBE VENT TUBE HUB TYPE INDICATES THE TYPE OF VENT TUBE HUB PROVIDED. SELECT REPLY CODE 10AJ88 CJTLD /D/ 18TYPE,ADDITIVE ADDITIVE TYPE INDICATES THE TYPE OF ADDITIVE PROVIDED. SELECT REPLY CODE 10AH24 CJTMJ 04DIAMETER,OVERALL,TOP TOP OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF THE TOP OF AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 CJTNJ 04DIAMETER,OVERALL,BOTTOM BOTTOM OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF THE BOTTOM OF AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 CJTPJ /D/ 04LENGTH,OVERALL,STOPPER STOPPER OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE STOPPER. 2D AND 1B MODE REPLY21AA051AC20 CJTQD /D/ 07PLATE,COVER COVER PLATE AN INDICATION OF WHETHER OR NOT A COVER PLATE IS INCLUDED. SELECT REPLY CODE 10AA49 CJTRD /D/ 07RECESS,LUBRICATION,INTERNAL INTERNAL LUBRICATION RECESS AN INDICATION OF WHETHER OR NOT AN INTERNAL RECESS FOR LUBRICATION IS INCLUDED. SELECT REPLY CODE 10AA49 CJTSD /D/ 09MATERIAL,TUBE,REGULATING REGULATING TUBE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE REGULATING TUBE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CJTTD /D/ 07HANDLE,GRIP GRIP HANDLE AN INDICATION OF WHETHER OR NOT A GRIP HANDLE IS INCLUDED. SELECT REPLY CODE 10AA49 CJTWJ 04DIAMETER,OUTSIDE,SPIGOT SPIGOT OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SPIGOT,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJTXJ /D/ 04DEPTH,SPIGOT SPIGOT DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE SPIGOT,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CJTYD /D/ 18TYPE,BAND BAND TYPE INDICATES THE TYPE OF BAND PROVIDED. SELECT REPLY CODE 10AL63 CJTZJ /D/ 04DIAMETER,ROPE,WIRE WIRE ROPE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A WIRE ROPE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJWBD 19ATTACHMENT FOR WHICH DESIGNED,ANCHOR ANCHOR ATTACHMENT FOR WHICH DESIGNED THE ATTACHMENT THE ANCHOR IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AC52 CJWCA 12QUANTITY,HOLE,GRADUATED GRADUATED HOLE QUANTITY THE NUMBER OF GRADUATED HOLES PROVIDED. 1A MODE REPLY 0 CJWDD /D/ 07PUNCH,RIVETING RIVETING PUNCH AN INDICATION OF WHETHER OR NOT A RIVETING PUNCH IS INCLUDED. SELECT REPLY CODE 10AA49 CJWFD /D/ 07DEPRESSION,CONICAL,GEOMETRICALLY CENTERED GEOMETRICALLY CENTERED CONICAL DEPRESSION AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES A GEOMETRICALLY CENTERED CONICAL DEPRESSION. SELECT REPLY CODE 10AA49 CJWGJ /D/T10RANGE,CUT,SIZE,LENS LENS SIZE CUT RANGE THE MINIMUM AND MAXIMUM LENS SIZE THE ITEM IS DESIGNED TO CUT. 1D AND 1F MODE REPLY11AA05 CJWHA /D/ 12QUANTITY,FACE FACE QUANTITY THE NUMBER OF FACES ON THE ITEM. 1A MODE REPLY 0 CJWJD /D/ 07FEATURE,MOUNTED,HOLDER HOLDER MOUNTED FEATURE AN INDICATION OF WHETHER OR NOT A HOLDER MOUNTED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CJWKJ /D/ 04SIZE,EYE EYE SIZE DESIGNATES THE SIZE OF THE EYE. 1D AND 1B MODE REPLY11AA05 CJWLD 11METHOD,OPERATION,STAND STAND OPERATION METHOD THE MEANS BY WHICH THE STAND IS OPERATED. SELECT REPLY CODE 10AC58 CJWMD /D/ 07ATTACHMENT,CHAIR CHAIR ATTACHMENT AN INDICATION OF WHETHER OR NOT A CHAIR ATTACHMENT IS INCLUDED. SELECT REPLY CODE 10AA49 CJWNJ /D/ 10TEMP RATING,POINT,SOFTENING SOFTENING POINT TEMP RATING AN INDICATION OF THE RATED SOFTENING POINT TEMPERATURE. 1D AND 1B MODE REPLY13AJ40 CJWPJ /D/ 10TEMP RATING,MINIMUM,LIQUID POINT LIQUID POINT MINIMUM TEMP RATING THE LOWEST TEMPERATURE AT WHICH A SUBSTANCE BECOMES COMPLETELY LIQUID. 1D AND 1B MODE REPLY13AJ40 CJWQG 10VISCOSITY IN SAYBOLT UNIVERSAL SECONDS VISCOSITY IN SAYBOLT UNIVERSAL SECONDS THE KINEMATIC RATING AS MEASURED BY A SAYBOLT VISCOSIMETER. FULL TEXT WRITE-IN 0 CJWRG 10PERCENTAGE AT SPECIFIED TEMP,EVAPORATION EVAPORATION PERCENTAGE AT SPECIFIED TEMP THE TEMPERATURE AT WHICH A GIVEN PERCENTAGE OF A SUBSTANCE IS EVAPORATED. FULL TEXT WRITE-IN 0 CJWSD 19STIPULATION,ADDITIVE ADDITIVE STIPULATION AN INDICATION OF THE ADDITIVE REQUIREMENT OR RESTRICTION. SELECT REPLY CODE 10AA65 CJWTB 10NUMBER,EMULSION,STEAM,MAXIMUM MAXIMUM STEAM EMULSION NUMBER AN INDICATION OF THE HIGHEST STEAM EMULSION NUMBER. 1B MODE REPLY 0 CJWWG 19NUMBER,COLOR,MAXIMUM MAXIMUM COLOR NUMBER THE LUMINANCE TRANSMITTANCE RATING OF A SAMPLE TO A FIXED COLOR STANDARD. FULL TEXT WRITE-IN 0 CJWXD /D/ 09MATERIAL,WRAPPER,FOIL FOIL WRAPPER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FOIL WRAPPER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CJWYJ /D/ 04LENGTH,CAPSULE CAPSULE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CAPSULE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CJWZJ /D/ 04DIAMETER,CAPSULE CAPSULE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CAPSULE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJXBJ /D/ 04WIDTH,CAPSULE CAPSULE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A CAPSULE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CJXCD /D/ 03DESIGNATION,GRADE,WAX WAX GRADE DESIGNATION THE DESIGNATION OF THE GRADE BY WHICH THE WAX IS IDENTIFIED. SELECT REPLY CODE 10AL91 CJXDG /D/ 19SPEC/STD,WAX WAX SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE WAX. FULL TEXT WRITE-IN 0 CJXFJ /D/ 10WEIGHT PER CAPSULE,WAX WAX WEIGHT PER CAPSULE THE AMOUNT OF WAX CONTAINED IN A SINGLE CAPSULE. 2D AND 1B MODE REPLY23AJ401AC20 CJXGJ /D/ 13THREAD SIZE DESIGNATION,PIPE,NOMINAL NOMINAL PIPE THREAD SIZE DESIGNATION THE INDUSTRIAL DESIGNATION OR TERM BY WHICH THE STANDARD PIPE THREAD SIZE IS IDENTIFIED. 1D AND 1B MODE REPLY11AA05 CJXHJ 10TEMP AT SPECIFIC GRAVITY RATIO,SUBSTANCE/WATER SUBSTANCE/WATER TEMP AT SPECIFIC GRAVITY RATIO THE TEMPERATURES OF THE SUBSTANCE OR MASS AND THE WATER AT WHICH THE SPECIFIC GRAVITY RATIO IS DETERMINED. 1D AND 1B MODE REPLY13AJ40 CJXJD /D/ 19CONFIGURATION,TOOTH TOOTH CONFIGURATION AN INDICATION OF THE PHYSCIAL CONFIGURATION OF THE TOOTH. SELECT REPLY CODE 10AE98 CJXKD /D/ 08LOCATION,EDGE,BEVELED BEVELED EDGE LOCATION INDICATES THE LOCATION OF THE BEVELED EDGE(S) IN OR ON THE ITEM. SELECT REPLY CODE 10AJ91 CJXLA 12QUANTITY PER PAD,SHEET SHEET QUANTITY PER PAD THE NUMBER OF SHEETS IN EACH PAD. 1A MODE REPLY 0 CJXMJ 03DESIGNATION,WEIGHT,SUBSTANCE SUBSTANCE WEIGHT DESIGNATION A MEASUREMENT OF WEIGHT BASED ON THE SIZE AND NUMBER OF SHEETS. 3D AND 1B MODE REPLY32AG671AC202AH05 CJXND /D/ 07CAN,DISPENSER,PRESSURE PRESSURE DISPENSER CAN AN INDICATION OF WHETHER OR NOT A PRESSURE DISPENSER CAN IS PROVIDED. SELECT REPLY CODE 10AB22 CJXPA /D/ 12QUANTITY PER SECTION,CLIP CLIP QUANTITY PER SECTION THE NUMBER OF CLIPS IN EACH SECTION. 1A MODE REPLY 0 CJXQD /D/ 18TYPE,TAPE TAPE TYPE INDICATES THE TYPE OF TAPE PROVIDED. SELECT REPLY CODE 10AL63 CJXRG 03DESIGNATION,WEIGHT WEIGHT DESIGNATION THE WEIGHT BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND DESIGNATED. FULL TEXT WRITE-IN 0 CJXSJ 04HEIGHT,WALL,REAR REAR WALL HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE REAR WALL,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CJXTJ 04DIAMETER,INSIDE,WORKING END WORKING END INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WORKING END,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJXWJ 04DIAMETER,OUTLET,TUBE TUBE OUTLET DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBE OUTLET,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJXXJ /D/ 04LENGTH,SPRING,BASE TENSION BASE TENSION SPRING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BASE TENSION SPRING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CJXYD /D/ 07SPRING,GUARD GUARD SPRING AN INDICATION OF WHETHER OR NOT A GUARD SPRING IS INCLUDED. MRC DISCONTINUED AND REPLACED WITH MRC CBBL AND REPLY CODE CGS, SPRING GUARD ON 03/28/2024. SELECT REPLY CODE 10AA49 CJXZJ 10CAPACITY RATING,COMPRESSOR,MAXIMUM MAXIMUM COMPRESSOR CAPACITY RATING THE MAXIMUM CAPACITY FOR WHICH THE COMPRESSOR IS RATED. 1D AND 1B MODE REPLY12AB49 CJYBJ 10PRESSURE RATING,DEHYDRATOR,MAXIMUM MAXIMUM DEHYDRATOR PRESSURE RATING THE MAXIMUM PRESSURE FOR WHICH THE DEHYDRATOR IS RATED. 1D AND 1B MODE REPLY12AB49 CJYCD /D/ 07MIXER,MATERIAL,DIE DIE MATERIAL MIXER AN INDICATION OF WHETHER OR NOT A DIE MATERIAL MIXER IS PROVIDED. SELECT REPLY CODE 10AB22 CJYDA 12QUANTITY,MIXER MIXER QUANTITY THE NUMBER OF MIXERS PROVIDED. 1A MODE REPLY 0 CJYFD /D/ 11METHOD,OPERATION,COVER COVER OPERATION METHOD THE MEANS USED TO OPERATE THE COVER. SELECT REPLY CODE 10AC58 CJYGD 11METHOD,OPERATION,DOOR DOOR OPERATION METHOD THE MEANS USED TO OPERATE THE DOOR. SELECT REPLY CODE 10AC58 CJYHD /D/ 07RHEOSTAT,OPERATED,FOOT FOOT OPERATED RHEOSTAT AN INDICATION OF WHETHER OR NOT A FOOT OPERATED RHEOSTAT IS PROVIDED. SELECT REPLY CODE 10AB22 CJYJJ 04LENGTH AT OPENING,SURFACE,GRINDING GRINDING SURFACE LENGTH AT OPENING A MEASUREMENT OF THE LONGEST DIMENSION OF THE GRINDING SURFACE,MEASURED AT THE OPENING OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CJYKJ 04WIDTH AT OPENING,SURFACE,GRINDING GRINDING SURFACE WIDTH AT OPENING A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE GRINDING SURFACE,MEASURED AT THE OPENING OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CJYLJ 04DEPTH,INSIDE,CHAMBER,WORKING WORKING CHAMBER INSIDE DEPTH A MEASUREMENT BETWEEN SPECIFIED INSIDE POINTS OF THE WORKING CHAMBER,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CJYMJ 04DIAMETER,INSIDE,WORKING CHAMBER WORKING CHAMBER INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WORKING CHAMBER,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJYNJ /D/A12QUANTITY PER RANGE PER INDICATOR,STEP STEP QUANTITY PER RANGE PER INDICATOR THE NUMBER OF STEPS WITHIN A SPECIFIED RANGE PER INDIVIDUAL INDICATOR. 1D AND 1A MODE REPLY13AJ91 CJYPH /D/ 01COLOR PER INDICATOR,MARKING,DIAL SCALE DIAL SCALE MARKING COLOR PER INDICATOR THE HUE OR TINT OF THE DIAL SCALE MARKING/S/ PER INDIVIDUAL INDICATOR. 2D MODE REPLY 26AD063AJ91 CJYQH /D/ 01COLOR PER INDICATOR,BACKGROUND BACKGROUND COLOR PER INDICATOR THE HUE OR TINT OF THE BACKGROUND FOR EACH INDIVIDUAL INDICATOR. 2D MODE REPLY 26AD063AJ91 CJYRJ /D/ 04DISTANCE BETWEEN LOOP AND PRONG,CENTER TO CENTER,SMALLER SMALLER CENTER TO CENTER DISTANCE BETWEEN LOOP AND PRONG NONE. 2D AND 1B MODE REPLY21AA051AC20 CJYSJ 04DIMENSION,LOOP/HOLDING LOOP/HOLDING DIMENSION NONE. 2D AND 1B MODE REPLY21AA051AC20 CJYTJ 04HEIGHT,SMALLEST SMALLEST HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CJYWG /D/ 04SIZE,HOLE,SECOND SECOND HOLE SIZE NONE. FULL TEXT WRITE-IN 0 CJYXA /D/ 16STYLE,SPINDLE SPINDLE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SPINDLE. 1A MODE REPLY 0 CJYYD /D/ 09MATERIAL,ROSE ROSE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ROSE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CJYZJ /D/ 04DIAMETER,ROSE ROSE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A ROSE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJZBJ /D/ 04WIDTH,OVERALL,ROSE ROSE OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ROSE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CJZCJ /D/ 04LENGTH,OVERALL,ROSE ROSE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ROSE. 2D AND 1B MODE REPLY21AA051AC20 CJZDJ /D/ 10OFFSET,MAXIMUM,LEVER LEVER MAXIMUM OFFSET NONE. 1D AND 1B MODE REPLY11AA05 CJZFJ 10OFFSET,MAXIMUM,BOLT BOLT MAXIMUM OFFSET NONE. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 1D AND 1B MODE REPLY11AA05 CJZGJ 04HEIGHT ABOVE BEARING SURFACE HEIGHT ABOVE BEARING SURFACE NONE. 2D AND 1B MODE REPLY21AA051AC20 CJZHJ /D/ 04WIDTH,SURFACE,BASE BASE SURFACE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CJZJL 16STYLE,STRIKE STRIKE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE STRIKE. 1L MODE REPLY 0 CJZKD /D/ 09MATERIAL,PLATE,FLOOR FLOOR PLATE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FLOOR PLATE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CJZLD /D/ 09MATERIAL,BRACKET,MOUNTING MOUNTING BRACKET MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MOUNTING BRACKET IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CJZMD /D/ 07ATTACHMENT,BACK,HOLD HOLD BACK ATTACHMENT AN INDICATION OF WHETHER OR NOT A HOLD BACK ATTACHMENT IS INCLUDED. SELECT REPLY CODE 10AA49 CJZNB /D/ 04ANGLE IN DEG,HOLDING HOLDING ANGLE IN DEG THE NUMBER OF DEGREES THE ITEM IS HELD AWAY FROM ITS NORMAL POSITION. 1B MODE REPLY 0 CJZPD /D/ 18TYPE,DEVICE,FUSIBLE FUSIBLE DEVICE TYPE INDICATES THE TYPE OF FUSIBLE DEVICE PROVIDED. SELECT REPLY CODE 10AC52 CJZQD /D/ 07HOOK/KEEPER HOOK/KEEPER AN INDICATION OF WHETHER OR NOT A HOOK AND/OR KEEPER IS INCLUDED. SELECT REPLY CODE 10AA49 CJZRJ /D/ 04HEIGHT ABOVE FLOOR HEIGHT ABOVE FLOOR A MEASUREMENT FROM THE FLOOR SURFACE TO THE TOP OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CJZSJ /D/ 04DIAMETER,PLATE,BASE BASE PLATE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BASE PLATE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CJZTA 12QUANTITY,AXLE AXLE QUANTITY THE NUMBER OF AXLES PROVIDED. 1A MODE REPLY 0 CJZWD 18TYPE,TRUCK TRUCK TYPE INDICATES THE TYPE OF TRUCK PROVIDED. SELECT REPLY CODE 10AK54 CJZXA 12QUANTITY PER AXLE,WHEEL WHEEL QUANTITY PER AXLE THE NUMBER OF WHEELS INCLUDED ON EACH AXLE. 1A MODE REPLY 0 CJZYD /D/ 17SURFACE TREATMENT,WHEEL WHEEL SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF A WHEEL. SELECT REPLY CODE 10AD09 CJZZJ 04DIAMETER,OUTSIDE,WHEEL WHEEL OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WHEEL,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CKBBD /D/ 09MATERIAL,APRON APRON MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH AN APRON IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CKBCD /D/ 17SURFACE TREATMENT,APRON APRON SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE APRON SURFACE. SELECT REPLY CODE 10AD09 CKBDD /D/ 18TYPE,APRON APRON TYPE INDICATES THE TYPE OF APRON PROVIDED. SELECT REPLY CODE 10AK54 CKBFJ /D/T10RANGE,ADJUSTMENT,LATERAL LATERAL ADJUSTMENT RANGE THE MINIMUM AND MAXIMUM LIMITS TO WHICH THE ITEM MAY BE LATERALLY ADJUSTED. 1D AND 1F MODE REPLY11AA05 CKBGD /D/ 07FEATURE,ARRANGEMENT,APRON SWIVEL APRON SWIVEL ARRANGEMENT FEATURE AN INDICATION OF WHETHER OR NOT AN APRON SWIVEL ARRANGEMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CKBHJ /D/ 04WIDTH,OVERALL,APRON APRON OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE APRON,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CKBJJ /D/ 04THICKNESS,MATERIAL,APRON APRON MATERIAL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE APRON MATERIAL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CKBKJ /D/ 04LENGTH,OVERALL,APRON APRON OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE APRON. 2D AND 1B MODE REPLY21AA051AC20 CKBLD /D/ 07FEATURE,ADJUSTABILITY,VERTICAL VERTICAL ADJUSTABILITY FEATURE AN INDICATION OF WHETHER OR NOT A VERTICAL ADJUSTABILITY FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CKBMD /D/ 07FEATURE,SURFACE,RAISED RAISED SURFACE FEATURE AN INDICATION OF WHETHER OR NOT A RAISED SURFACE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CKBNJ 04LENGTH,SHAFT,KNOB KNOB SHAFT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CKBPJ 04LENGTH,KNOB,DUAL DUAL KNOB LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CKBQJ 04DIAMETER,KNOB,INNER INNER KNOB DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CKBRJ /D/ 04THICKNESS,KNOB,INNER INNER KNOB THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CKBSA /D/ 13THREAD SIZE,FACILITY,MOUNTING MOUNTING FACILITY THREAD SIZE NONE. 1A MODE REPLY 0 CKBTJ 04DIAMETER,INSIDE,RECESS RECESS INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A RECESS,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CKBWJ 04DIAMETER,INSIDE,MAJOR,RECESS RECESS MAJOR INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE RECESS,AND TERMINATES AT THE LARGEST INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CKBYG /D/ 19CONFIGURATION,HOLE,BOLT BOLT HOLE CONFIGURATION THE NARRATIVE EXPRESSION USED FOR INDICATING THE CONFIGURATION OF THE BOLT HOLE. FULL TEXT WRITE-IN 0 CKBZB /D/ 04ANGLE IN DEG,EDGE,FEATHER FEATHER EDGE ANGLE IN DEG THE ANGLE OF THE FEATHERED EDGE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CKCBJ 04THICKNESS,PAD PAD THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CKCCJ 04DISTANCE BETWEEN EYE CENTERLINE AND PAD BOTTOM DISTANCE BETWEEN EYE CENTERLINE AND PAD BOTTOM NONE. 2D AND 1B MODE REPLY21AA051AC20 CKCDJ 04LENGTH FROM PLATE END TO EYE CENTERLINE LENGTH FROM PLATE END TO EYE CENTERLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 CKCFJ 04DISTANCE BETWEEN PADS DISTANCE BETWEEN PADS NONE. 2D AND 1B MODE REPLY21AA051AC20 CKCGJ 04DISTANCE FROM EYE STOCK OUTER EDGE TO EYE DISTANCE FROM EYE STOCK OUTER EDGE TO EYE NONE. 2D AND 1B MODE REPLY21AA051AC20 CKCHJ 04DIAMETER,LONG,EYE INSIDE EYE INSIDE LONG DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CKCJJ 04DIAMETER,SHORT,EYE INSIDE EYE INSIDE SHORT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CKCKA 12QUANTITY,COMBINATION COMBINATION QUANTITY THE NUMBER OF COMBINATIONS PROVIDED. 1A MODE REPLY 0 CKCLD /D/ 07KEY,CHANGE CHANGE KEY AN INDICATION OF WHETHER OR NOT A CHANGE KEY IS INCLUDED. SELECT REPLY CODE 10AA49 CKCMA 12QUANTITY,PADLOCK PADLOCK QUANTITY THE NUMBER OF PADLOCKS PROVIDED. 1A MODE REPLY 0 CKCNA 12QUANTITY,GROUP,SEPARATE PADLOCK SEPARATE PADLOCK GROUP QUANTITY THE NUMBER OF SEPARATE PADLOCK GROUPS PROVIDED. 1A MODE REPLY 0 CKCPA 12QUANTITY PER GROUP,PADLOCK PADLOCK QUANTITY PER GROUP THE NUMBER OF PADLOCKS IN EACH GROUP. 1A MODE REPLY 0 CKCQD 18TYPE,KEYING,INDIVIDUAL GROUP INDIVIDUAL GROUP KEYING TYPE INDICATES THE TYPE OF KEYING PROVIDED WITH EACH INDIVIDUAL GROUP. SELECT REPLY CODE 10AK54 CKCRD /D/ 07FEATURE,DESIGN,INDIVIDUAL GROUP MASTER KEY INDIVIDUAL GROUP MASTER KEY DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A MASTER KEY DESIGN FEATURE IS PROVIDED FOR EACH INDIVIDUAL GROUP. SELECT REPLY CODE 10AB22 CKCSD /D/ 07FEATURE,DESIGN,GRAND MASTER KEY GRAND MASTER KEY DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A GRAND MASTER KEY DESIGN FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CKCTD /D/ 07FEATURE,PADLOCK,GROUPED GROUPED PADLOCK FEATURE AN INDICATION OF WHETHER OR NOT A GROUPED PADLOCK FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CKCWD 18TYPE,KEYING,INDIVIDUAL PADLOCK INDIVIDUAL PADLOCK KEYING TYPE INDICATES THE TYPE OF KEYING PROVIDED WITH EACH INDIVIDUAL PADLOCK. SELECT REPLY CODE 10AK54 CKCXD /D/ 07FEATURE,DESIGN,INDIVIDUAL PADLOCK MASTER KEY INDIVIDUAL PADLOCK MASTER KEY DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A MASTER KEY DESIGN FEATURE IS PROVIDED FOR EACH INDIVIDUAL PADLOCK. SELECT REPLY CODE 10AB22 CKCYJ A12QUANTITY,SETTING,DIAL DIAL SETTING QUANTITY THE NUMBER OF DIAL SETTINGS PROVIDED. 1D AND 1A MODE REPLY11AC20 CKCZA 12QUANTITY,KNOB,COMBINATION COMBINATION KNOB QUANTITY THE NUMBER OF COMBINATION KNOBS PROVIDED. 1A MODE REPLY 0 CKDBD /D/ 19CONSTRUCTION,CASE CASE CONSTRUCTION THE STRUCTURAL CHARACTERISTIC OF THE CASE. SELECT REPLY CODE 10AL59 CKDCD /D/ 07REMOVABILITY,CORE,CASE CASE CORE REMOVABILITY AN INDICATION OF WHETHER OR NOT THE CASE CORE IS REMOVABLE. SELECT REPLY CODE 10AC29 CKDDD /D/ 09MATERIAL,SHACKLE SHACKLE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHACKLE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CKDFD /D/ 07INDICATOR,CASEHARDENING,SHACKLE SHACKLE CASEHARDENING INDICATOR INDICATES WHETHER OR NOT A FERROUS ALLOY SHACKLE HAS BEEN SUBJECTED TO A PROCESS WHEREBY THE OUTER PORTION IS MADE SUBSTANTIALLY HARDER THAN THE INNER PORTION OR CORE. SELECT REPLY CODE 10AA70 CKDGD /D/ 17SURFACE TREATMENT,SHACKLE SHACKLE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A SHACKLE SURFACE. SELECT REPLY CODE 10AD09 CKDHD /D/ 07ADJUSTABILITY,SHACKLE SHACKLE ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE SHACKLE IS ADJUSTABLE. SELECT REPLY CODE 10AB00 CKDJJ 10CLEARANCE,SHACKLE SHACKLE CLEARANCE A MEASUREMENT OF THE DISTANCE BY WHICH THE SHACKLE CLEARS ANOTHER OBJECT. 2D AND 1B MODE REPLY21AA051AC20 CKDKJ 04DIAMETER,SHACKLE SHACKLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHACKLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CKDLJ 04LENGTH,PRONG/LIP PRONG/LIP LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CKDMB /D/ 04ANGLE IN DEG,CURVATURE CURVATURE ANGLE IN DEG THE RATE OF CHANGE OF A CURVATURE ANGLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CKDND /D/ 07ATTACHMENT,LEAKE LEAKE ATTACHMENT AN INDICATION OF WHETHER OR NOT A LEAKE ATTACHMENT IS INCLUDED. SELECT REPLY CODE 10AA49 CKDPD 07SHAPE,EYE,FRAME FRAME EYE SHAPE THE PHYSICAL CONFIGURATION OF THE FRAME EYE. SELECT REPLY CODE 10AD07 CKDQA /D/ 12QUANTITY,PARTITION,DRAWER DRAWER PARTITION QUANTITY THE NUMBER OF DRAWER PARTITIONS PROVIDED. 1A MODE REPLY 0 CKDRD /D/ 07SHELF,COMPARTMENT COMPARTMENT SHELF AN INDICATION OF WHETHER OR NOT A COMPARTMENT SHELF IS INCLUDED. SELECT REPLY CODE 10AA49 CKDSJ 04LENGTH,OVERALL,TOP TOP OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE TOP. 1D AND 1B MODE REPLY11AA05 CKDTJ T10RANGE,ADJUSTMENT,TOP VERTICAL TOP VERTICAL ADJUSTMENT RANGE THE MINIMUM AND MAXIMUM LIMITS TO WHICH THE TOP MAY BE VERTICALLY ADJUSTED. 1D AND 1F MODE REPLY11AA05 CKDWD /D/ 18TYPE ACCOMMODATED,LAP LAP TYPE ACCOMMODATED INDICATES THE TYPE OF LAP/S/ THE ITEM IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AK54 CKDXA /D/ 12QUANTITY ACCOMMODATED,LAP LAP QUANTITY ACCOMMODATED THE NUMBER OF LAPS THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 CKDYG /D/ 04SIZE ACCOMMODATED,LAP LAP SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE LAP THE ITEM IS DESIGNED TO ACCOMMODATE. FULL TEXT WRITE-IN 0 CKDZD /D/ 07RACK,GAGE,DETACHABLE DETACHABLE GAGE RACK AN INDICATION OF WHETHER OR NOT A DETACHABLE GAGE RACK IS INCLUDED. SELECT REPLY CODE 10AA49 CKFBD /D/ 07LEGS,BENCH,FOLDING FOLDING BENCH LEGS AN INDICATION OF WHETHER OR NOT FOLDING BENCH LEGS ARE INCLUDED. SELECT REPLY CODE 10AA49 CKFCD /D/ 07STOOL,RETRACTABLE RETRACTABLE STOOL AN INDICATION OF WHETHER OR NOT A RETRACTABLE STOOL IS INCLUDED. SELECT REPLY CODE 10AA49 CKFDD /D/ 07RECEPTACLE,POWER POWER RECEPTACLE AN INDICATION OF WHETHER OR NOT A POWER RECEPTACLE IS INCLUDED. SELECT REPLY CODE 10AA49 CKFFD 08LOCATION,SHELF SHELF LOCATION INDICATES THE LOCATION OF THE SHELF/VES/ ON THE ITEM. SELECT REPLY CODE 10AJ91 CKFGJ 04HEIGHT,SHELF SHELF HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE SHELF,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 CKFHD /D/ 07TRAY,WORK,SLIDING SLIDING WORK TRAY AN INDICATION OF WHETHER OR NOT A SLIDING WORK TRAY IS INCLUDED. SELECT REPLY CODE 10AA49 CKFJD /D/ 07HOLDER,LABEL LABEL HOLDER AN INDICATION OF WHETHER OR NOT A LABEL HOLDER IS INCLUDED. SELECT REPLY CODE 10AA49 CKFKJ /D/ 04LENGTH,OVERALL,SLIT SLIT OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE SLIT. 1D AND 1B MODE REPLY11AA05 CKFLJ 04WIDTH,OVERALL,SLIT SLIT OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A SLIT,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CKFMJ /D/ 04LENGTH,FRONT TO BACK FRONT TO BACK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION FROM THE FRONT TO THE BACK OF THE ITEM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CKFND /D/ 07AXLE AXLE AN INDICATION OF WHETHER OR NOT AN AXLE IS INCLUDED. SELECT REPLY CODE 10AA49 CKFPD /D/ 07DEVICE,CLAMPING CLAMPING DEVICE AN INDICATION OF WHETHER OR NOT A CLAMPING DEVICE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CKFQD 04SIZE,HANDLE HANDLE SIZE DESIGNATES THE SIZE OF THE HANDLE/S/. SELECT REPLY CODE 10AF81 CKFRB /D/ 10POWER RATING IN DIOPTERS,LENS,FLAT PRISM FLAT PRISM LENS POWER RATING IN DIOPTERS THE RATED POWER OF THE FLAT PRISM LENS,EXPRESSED IN DIOPTERS. 1B MODE REPLY 0 CKFSD /D/ 14SHAPE,WIRE,EYE EYE WIRE SHAPE THE PHYSICAL CONFIGURATION OF THE EYE WIRE. SELECT REPLY CODE 10AD07 CKFTJ /D/ 04LENGTH,WIRE,EYE EYE WIRE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE EYE WIRE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CKFWJ /D/ 04WIDTH,WIRE,EYE EYE WIRE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE EYE WIRE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CKFXJ /D/ 04THICKNESS,WIRE,EYE EYE WIRE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF AN EYE WIRE,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 CKFYD 14SHAPE,END,WORKING WORKING END SHAPE THE PHYSICAL CONFIGURATION OF THE WORKING END. SELECT REPLY CODE 10AD07 CKFZD 18TYPE,TIP,WORKING END WORKING END TIP TYPE INDICATES THE TYPE OF TIP PROVIDED ON THE WORKING END. SELECT REPLY CODE 10AK84 CKGBJ 10POWER RATING IN DIOPTERS POWER RATING IN DIOPTERS THE REFRACTIVE POWER OF A LENS OR PRISM NUMERICALLY EQUAL TO THE RECIPROCAL OF THE FOCAL LENGTH,EXPRESSED IN DIOPTERS. 2D AND 1B MODE REPLY21AH081AC20 CKGCB 10CURVE RATING IN DIOPTERS CURVE RATING IN DIOPTERS THE RATED CURVE OF THE ITEM,EXPRESSED IN DIOPTERS. 1B MODE REPLY 0 CKGDF T10RANGE,POWER,LENS NEGATIVE DIOPTER LENS NEGATIVE DIOPTER POWER RANGE THE MINIMUM AND MAXIMUM NEGATIVE POWER OF THE LENS,EXPRESSED IN DIOPTERS. 1F MODE REPLY 0 CKGFF T10RANGE,POWER,LENS POSITIVE DIOPTER LENS POSITIVE DIOPTER POWER RANGE THE MINIMUM AND MAXIMUM POSITIVE POWER OF THE LENS,EXPRESSED IN DIOPTERS. 1F MODE REPLY 0 CKGGB 10INTERVAL IN DIOPTERS,STEP,INDIVIDUAL INDIVIDUAL STEP INTERVAL IN DIOPTERS A MEASUREMENT OF THE INDIVIDUAL STEP INTERVAL ON THE ITEM,EXPRESSED IN DIOPTERS. 1B MODE REPLY 0 CKGHB 10POWER RATING,DIOPTER,PRISM PRISM DIOPTER POWER RATING A MEASUREMENT OF THE RATED PRISM POWER,EXPRESSED IN DIOPTERS. 1B MODE REPLY 0 CKGJA 12QUANTITY,PRISM,ADDITIONAL ADDITIONAL PRISM QUANTITY THE NUMBER OF ADDITIONAL PRISMS PROVIDED. 1A MODE REPLY 0 CKGKB 10POWER RATING,DIOPTER,ADDITIONAL PRISM ADDITIONAL PRISM DIOPTER POWER RATING THE RATED ADDITIONAL PRISM POWER,EXPRESSED IN DIOPTERS. 1B MODE REPLY 0 CKGLD /D/ 07APERTURE,ZERO,LENS LENS ZERO APERTURE AN INDICATION OF WHETHER OR NOT THE LENS INCLUDES A ZERO APERTURE. SELECT REPLY CODE 10AA49 CKGMD 19CONTOUR FOR WHICH DESIGNED,SURFACE,LENS LENS SURFACE CONTOUR FOR WHICH DESIGNED THE LENS SURFACE CONTOUR FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AD07 CKGNJ 04WIDTH,RAIL,INTERMEDIATE INTERMEDIATE RAIL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE INTERMEDIATE RAIL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CKGPA 12QUANTITY,MUNTIN MUNTIN QUANTITY THE NUMBER OF MUNTINS PROVIDED. 1A MODE REPLY 0 CKGQJ 04WIDTH,MUNTIN MUNTIN WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MUNTIN,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CKGRG /D/ 19ARRANGEMENT,SASH SASH ARRANGEMENT AN INDICATION OF THE ARRANGEMENT OF THE SASH. FULL TEXT WRITE-IN 0 CKGSJ /D/ 04WIDTH,SASH SASH WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SASH,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CKGTJ /D/ 04HEIGHT,SASH SASH HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE SASH,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CKGWD 18TYPE,MATERIAL,LIGHT LIGHT MATERIAL TYPE INDICATES THE TYPE OF LIGHT MATERIAL PROVIDED. SELECT REPLY CODE 10AN48 CKGXD 19SPECIES,WOOD,FRAME FRAME WOOD SPECIES THE BOTANICAL VARIETY TO WHICH THE FRAME WOOD BELONGS. SELECT REPLY CODE 10AM00 CKGYD /D/ 09MATERIAL,MESH,WIRE WIRE MESH MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WIRE MESH IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT AND USE OF ISAC IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 CKGZA 04SIZE,AWG,MESH WIRE MESH WIRE AWG SIZE THE AMERICAN WIRE GAGE SIZE OF MESH WIRE. 1A MODE REPLY 0 CKHBD /D/ 17SURFACE TREATMENT,MESH,WIRE WIRE MESH SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE WIRE MESH SURFACE. PLEASE USE MRC SFTT WITH USE OF ISAC IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 CKHCG 11METHOD,ATTACHMENT,WIRE MESH WIRE MESH ATTACHMENT METHOD THE MEANS USED TO ATTACH THE WIRE MESH. FULL TEXT WRITE-IN 0 CKHDD /D/ 07GUARD,ORNAMENTAL,WIRE PROTECTION WIRE PROTECTION ORNAMENTAL GUARD AN INDICATION OF WHETHER OR NOT A WIRE PROTECTION ORNAMENTAL GUARD IS PROVIDED. SELECT REPLY CODE 10AB22 CKHFG /D/ 19CONDITION AND LOCATION,DRESSED DRESSED CONDITION AND LOCATION INDICATES THE DRESSED CONDITION OF THE ITEM AND THE LOCATION. FULL TEXT WRITE-IN 0 CKHGD 19RELATIONSHIP,SURFACE,SIDE SIDE SURFACE RELATIONSHIP AN INDICATION OF THE RELATIONSHIP OF THE SIDE SURFACE/S/ OF THE ITEM. SELECT REPLY CODE 10AF63 CKHHD 19RELATIONSHIP,SURFACE,BUTT END TO FACE BUTT END TO FACE SURFACE RELATIONSHIP THE RELATIONSHIP OF THE BUTT END WITH RESPECT TO THE FACE SURFACE(S). SELECT REPLY CODE 10AF63 CKHJG /D/ 03DESIGNATION,THICKNESS,EDGE EDGE THICKNESS DESIGNATION A DESIGNATION INDICATING THE THICKNESS OF THE EDGE OF THE ITEM. FULL TEXT WRITE-IN 0 CKHKJ /D/ 04THICKNESS,END,BUTT BUTT END THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE BUTT END,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CKHLD /D/ 19PROCESS,SEASONING SEASONING PROCESS THE PROCESS BY WHICH THE ITEM IS SEASONED. SELECT REPLY CODE 10AJ05 CKHMG /D/ 19SPEC/STD,TREATMENT TREATMENT SPEC/STD THE SPECIFICATION AND/OR STANDARD GOVERNING THE TREATMENT ON THE ITEM. FULL TEXT WRITE-IN 0 CKHNG 19NAME,ASSOCIATION,GRADING GRADING ASSOCIATION NAME THE NAME OF THE GRADING ASSOCIATION. FULL TEXT WRITE-IN 0 CKHPD /D/ 19SPECIES,WOOD,FACE FACE WOOD SPECIES THE BOTANICAL VARIETY TO WHICH THE FACE WOOD BELONGS. SELECT REPLY CODE 10AM00 CKHQD /D/ 18TYPE,SERVICE,RATED RATED SERVICE TYPE INDICATES THE TYPE OF RATED SERVICE OF THE ITEM. SELECT REPLY CODE 10AK54 CKHRD /D/ 19GRADE,MATERIAL,RATED RATED MATERIAL GRADE THE RATED MATERIAL GRADE OF THE ITEM. SELECT REPLY CODE 10AN24 CKHSD /D/ 19SPECIES,WOOD,CROSSBAND CROSSBAND WOOD SPECIES THE BOTANICAL VARIETY TO WHICH THE CROSSBAND WOOD BELONGS. SELECT REPLY CODE 10AM00 CKHTA /D/ 19GROUP,SPECIES,WOOD WOOD SPECIES GROUP THE GROUP BY WHICH THE WOOD SPECIES IS IDENTIFIED. 1A MODE REPLY 0 CKHWG /D/ 04ANGLE IN DEG/D/,EVEN NUMBERED PLY OTHER THAN 90 DEG TO FACE PLY GRAIN EVEN NUMBERED PLY OTHER THAN 90 DEG TO FACE PLY GRAIN ANGLE IN DEG/D/ THE POSITION OF THE EVEN NUMBERED PLIES WHEN OTHER THAN 90 DEGREES FROM THE FACE PLY GRAINS(S),EXPRESSED IN DEGREES. FULL TEXT WRITE-IN 0 CKHXD /D/ 08LOCATION,SURFACE,SANDED SANDED SURFACE LOCATION INDICATES THE LOCATION OF THE SANDED SURFACE/S/ ON THE ITEM. SELECT REPLY CODE 10AJ91 CKHYD /D/ 08LOCATION,USAGE,SINGLE SASH SINGLE SASH USAGE LOCATION INDICATES THE LOCATION AT WHICH THE SINGLE SASH IS TO BE USED. SELECT REPLY CODE 10AJ91 CKHZD 02DESIGN,EDGE,STILE STILE EDGE DESIGN THE DESIGN OF THE STILE EDGE(S). SELECT REPLY CODE 10AL25 CKJBJ 04HEIGHT,RAIL,BOTTOM BOTTOM RAIL HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BOTTOM RAIL,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CKJCJ 04HEIGHT,RAIL,TOP TOP RAIL HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE TOP RAIL,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CKJDJ /D/ 04HEIGHT,RAIL,MEETING MEETING RAIL HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE MEETING RAIL,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CKJFJ /D/ 04THICKNESS,RAIL,MEETING MEETING RAIL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE MEETING RAIL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CKJGD 02DESIGN,EDGE,BOTTOM RAIL BOTTOM RAIL EDGE DESIGN THE DESIGN OF THE BOTTOM RAIL EDGE. SELECT REPLY CODE 10AL25 CKJHD /D/ 02DESIGN,EDGE,MEETING RAIL MEETING RAIL EDGE DESIGN THE DESIGN OF THE MEETING RAIL EDGE. SELECT REPLY CODE 10AL25 CKJJD 19ARRANGEMENT,LIGHT LIGHT ARRANGEMENT AN INDICATION OF THE WAY THE LIGHT(S) IS ARRANGED. SELECT REPLY CODE 10AH86 CKJKA /D/ 12QUANTITY,LIGHT,EXTRA EXTRA LIGHT QUANTITY THE NUMBER OF EXTRA LIGHTS PROVIDED. 1A MODE REPLY 0 CKJLG 03DESIGNATION,GRADE GRADE DESIGNATION A DESIGNATION OF THE GRADE BY WHICH THE ITEM IS IDENTIFIED. FULL TEXT WRITE-IN 0 CKJMB /D/ 10CONTENT IN PERCENT,MOISTURE MOISTURE CONTENT IN PERCENT THE MOISTURE CONTENT IN THE ITEM,EXPRESSED IN PERCENT. 1B MODE REPLY 0 CKJNF T10RANGE,SCALE,CIRCULAR,LEFT LEFT CIRCULAR SCALE RANGE THE MINIMUM AND MAXIMUM LIMITS OF THE LEFT CIRCULAR SCALE. 1F MODE REPLY 0 CKJPD /D/ 07NOSEPIECE,GRADUATED GRADUATED NOSEPIECE AN INDICATION OF WHETHER OR NOT A GRADUATED NOSEPIECE IS INCLUDED. SELECT REPLY CODE 10AA49 CKJQD /D/ 07DEVICE,SIGHTING,CORNEAL CORNEAL SIGHTING DEVICE AN INDICATION OF WHETHER OR NOT A CORNEAL SIGHTING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 CKJRJ T10RANGE,MEASUREMENT,OUTSIDE OUTSIDE MEASUREMENT RANGE THE MINIMUM AND MAXIMUM LIMITS OF THE OUTSIDE MEASUREMENT. 1D AND 1F MODE REPLY11AA05 CKJSJ T10RANGE,MEASUREMENT,INSIDE INSIDE MEASUREMENT RANGE THE MINIMUM AND MAXIMUM LIMITS OF THE INSIDE MEASUREMENT. 1D AND 1F MODE REPLY11AA05 CKJTJ /D/ 04DEPTH,JAW JAW DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE JAW,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 CKJWD 08LOCATION,USAGE,VERNIER SCALE VERNIER SCALE USAGE LOCATION INDICATES THE LOCATION AT WHICH THE VERNIER SCALE IS TO BE USED. SELECT REPLY CODE 10AJ91 CKJXD /D/ 08LOCATION,SCALE,VERNIER VERNIER SCALE LOCATION INDICATES THE LOCATION OF THE VERNIER SCALE ON THE ITEM. SELECT REPLY CODE 10AJ91 CKJYD /D/ 07FEATURE,ADJUSTMENT,FINE FINE ADJUSTMENT FEATURE AN INDICATION OF WHETHER OR NOT A FINE ADJUSTMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CKJZD /D/ 07SET,JAW,INTEGRAL,ADDITIONAL ADDITIONAL INTEGRAL JAW SET AN INDICATION OF WHETHER OR NOT AN ADDITIONAL INTEGRAL JAW SET IS INCLUDED. SELECT REPLY CODE 10AA49 CKKBG 03DESIGNATOR,AIRCRAFT AIRCRAFT DESIGNATOR THE DESIGNATION WHICH IDENTIFIES THE AIRCRAFT. FULL TEXT WRITE-IN 0 CKKCD /D/ 07GAGE,DEPTH,INTEGRAL INTEGRAL DEPTH GAGE AN INDICATION OF WHETHER OR NOT AN INTEGRAL DEPTH GAGE IS INCLUDED. SELECT REPLY CODE 10AA49 CKKDA 12QUANTITY,TABLE,BLOCKING BLOCKING TABLE QUANTITY THE NUMBER OF BLOCKING TABLES INCLUDED. 1A MODE REPLY 0 CKKFD 18TYPE,TABLE,BLOCKING BLOCKING TABLE TYPE INDICATES THE TYPE OF BLOCKING TABLE PROVIDED. SELECT REPLY CODE 10AK54 CKKGD /D/ 07PROTRACTOR,TABLE,BLOCKING BLOCKING TABLE PROTRACTOR AN INDICATION OF WHETHER OR NOT A BLOCKING TABLE PROTRACTOR IS INCLUDED. SELECT REPLY CODE 10AA49 CKKHD 18TYPE,CHUCK,LENS LENS CHUCK TYPE INDICATES THE TYPE OF LENS CHUCK PROVIDED. SELECT REPLY CODE 10AK95 CKKJD /D/ 18TYPE,TARGET,LENS CENTERING,SIGHT TUBE SIGHT TUBE LENS CENTERING TARGET TYPE INDICATES THE TYPE OF SIGHT TUBE LENS CENTERING TARGET PROVIDED. SELECT REPLY CODE 10AK95 CKKKD /D/ 07FEATURE,ILLUMINATION,SIGHT TUBE SIGHT TUBE ILLUMINATION FEATURE AN INDICATION OF WHETHER OR NOT A SIGHT TUBE ILLUMINATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CKKLJ 04WIDTH,POSITION,CLOSED,NIB NIB CLOSED POSITION WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE NIB IN A CLOSED POSITION,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CKKMD 18TYPE,UNIT,PREHEATING PREHEATING UNIT TYPE INDICATES THE TYPE OF PREHEATING UNIT PROVIDED. SELECT REPLY CODE 10AA93 CKKNA /D/ 12QUANTITY ACCOMMODATED,WAFER,BLOCK AND PITCH BLOCK AND PITCH WAFER QUANTITY ACCOMMODATED THE NUMBER OF BLOCKS AND PITCH WAFERS THE UNIT IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 CKKPD /D/ 07DEVICE,TIMING,AUDIBLE AUDIBLE TIMING DEVICE AN INDICATION OF WHETHER OR NOT AN AUDIBLE TIMING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 CKKQD /D/ 07CONTROL,THERMOSTATIC,PREHEATING UNIT PREHEATING UNIT THERMOSTATIC CONTROL AN INDICATION OF WHETHER OR NOT A PREHEATING UNIT THERMOSTATIC CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 CKKRA /D/ 12QUANTITY ACCOMMODATED,BLOCK,CHILLING CHAMBER LENS CHILLING CHAMBER LENS BLOCK QUANTITY ACCOMMODATED THE NUMBER OF LENS BLOCKS THE CHILLING CHAMBER IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 CKKSJ /D/ 04LENGTH,CHAMBER,CHILLING CHILLING CHAMBER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CHILLING CHAMBER,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CKKTJ /D/ 04WIDTH,CHAMBER,CHILLING CHILLING CHAMBER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CHILLING CHAMBER,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CKKWJ /D/ 04DEPTH,CHAMBER,CHILLING CHILLING CHAMBER DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE CHILLING CHAMBER,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 CKKXD /D/ 07STAND,METAL METAL STAND AN INDICATION OF WHETHER OR NOT A METAL STAND IS INCLUDED. SELECT REPLY CODE 10AA49 CKKYD /D/ 07PETCOCK PETCOCK AN INDICATION OF WHETHER OR NOT A PETCOCK IS INCLUDED. SELECT REPLY CODE 10AA49 CKKZD 18TYPE,HANDREST HANDREST TYPE INDICATES THE TYPE OF HANDREST PROVIDED. SELECT REPLY CODE 10AK54 CKLBJ 04DIAMETER,OUTSIDE,GRINDING WHEEL GRINDING WHEEL OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GRINDING WHEEL,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CKLCJ /D/ 04WIDTH,FACE,GRINDING WHEEL GRINDING WHEEL FACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE GRINDING WHEEL,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CKLDD /D/ 07HEAD,OPERATED,INDEPENDENTLY INDEPENDENTLY OPERATED HEAD AN INDICATION OF WHETHER OR NOT AN INDEPENDENTLY OPERATED HEAD/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CKLFJ T04SIZE ACCOMMODATED,LENS LENS SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE LENS THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1F MODE REPLY11AA05 CKLGF T10RANGE IN DIOPTERS,GENERATING,CURVE CURVE GENERATING RANGE IN DIOPTERS A MEASUREMENT OF THE CURVE GENERATING RANGE OF THE ITEM,EXPRESSED IN DIOPTERS. 1F MODE REPLY 0 CKLHD /D/ 07DEVICE,PLOTTING,PRECISION PRECISION PLOTTING DEVICE AN INDICATION OF WHETHER OR NOT A PRECISION PLOTTING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 CKLJD 18TYPE,WHEEL,ABRASIVE ABRASIVE WHEEL TYPE INDICATES THE TYPE OF ABRASIVE WHEEL PROVIDED. SELECT REPLY CODE 10AF67 CKLKJ 10SPEED RATING,SURFACE,ABRASIVE WHEEL ABRASIVE WHEEL SURFACE SPEED RATING THE RATED SURFACE SPEED OF THE ABRASIVE WHEEL. 1D AND 1B MODE REPLY12AG67 CKLLD /D/ 07COLMASCOPE COLMASCOPE AN INDICATION OF WHETHER OR NOT A COLMASCOPE IS INCLUDED. SELECT REPLY CODE 10AA49 CKLMD /D/ 07SCALE,WEIGHT,INTEGRAL INTEGRAL WEIGHT SCALE AN INDICATION OF WHETHER OR NOT AN INTEGRAL WEIGHT SCALE IS INCLUDED. SELECT REPLY CODE 10AA49 CKLQJ /D/ 04THICKNESS,DRESSED DRESSED THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A DRESSED ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CKLRJ /D/ 04WIDTH,DRESSED DRESSED WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A DRESSED ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CKLSJ /D/ 04THICKNESS,ROUGH ROUGH THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A ROUGH ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CKLTJ /D/ 04WIDTH,ROUGH ROUGH WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A ROUGH ITEM,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CKLWJ /D/ 04LENGTH,ROUGH ROUGH LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A ROUGH ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CKLXH /D/ 11METHOD AND LOCATION,CUTTING CUTTING METHOD AND LOCATION THE MEANS USED TO CUT THE ITEM AND THE LOCATION. 2D MODE REPLY 22AJ023AJ91 CKLYD /D/ 19CHARACTERISTIC,WOOD WOOD CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC OF THE WOOD. SELECT REPLY CODE 10AN24 CKLZA /D/ 04SIZE,MESH,SCREEN,USS USS SCREEN MESH SIZE THE SCREEN MESH SIZE AS ESTABLISHED BY UNITED STATES STANDARD. 1A MODE REPLY 0 CKMBD /D/ 07SCRAP,WOOD,SOLID SOLID WOOD SCRAP AN INDICATION OF WHETHER OR NOT A SOLID WOOD SCRAP/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CKMCA /D/ 12QUANTITY,SIDE,SURFACED SURFACED SIDE QUANTITY THE NUMBER OF SIDES OF THE ITEM THAT ARE SURFACED. 1A MODE REPLY 0 CKMDD /D/ 19DEGREE,PEELING PEELING DEGREE THE EXTENT TO WHICH THE ITEM IS PEELED. SELECT REPLY CODE 10AK39 CKMFD /D/ 19EXTENT,TREATMENT TREATMENT EXTENT AN INDICATION OF THE EXTENT OF THE TREATMENT PROVIDED. SELECT REPLY CODE 10AK95 CKMGJ /D/ 10CONTENT,RETENTION,TREATMENT TREATMENT RETENTION CONTENT THE TREATMENT RETENTION CONTENT OF THE ITEM. 1D AND 1B MODE REPLY12AG67 CKMHJ /D/T04DIAMETER RANGE,BUTT BUTT DIAMETER RANGE THE MINIMUM AND MAXIMUM RANGE OF MEASUREMENTS OF A STRAIGHT LINE PASSING THROUGH THE CENTER OF THE ITEM. 1D AND 1F MODE REPLY11AA05 CKMJJ /D/ 10CIRCUMFERENCE,TOP TOP CIRCUMFERENCE THE MEASURED DISTANCE AROUND THE OUTSIDE SURFACE AT THE TOP OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CKMKJ /D/ 10CIRCUMFERENCE,BUTT BUTT CIRCUMFERENCE THE MEASURED DISTANCE AROUND THE OUTSIDE SURFACE AT THE BUTT OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CKMLJ /D/ 04DISTANCE BETWEEN CENTER HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN CENTER HOLES THE CENTER TO CENTER DISTANCE BETWEEN THE CENTER HOLES. 2D AND 1B MODE REPLY21AA051AC20 CKMMJ /D/ 04DISTANCE BETWEEN SIDE HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SIDE HOLES THE CENTER TO CENTER DISTANCE BETWEEN THE SIDE HOLES. 2D AND 1B MODE REPLY21AA051AC20 CKMNJ /D/ 04DISTANCE FROM END HOLE TO END DISTANCE FROM END HOLE TO END THE DISTANCE FROM THE END HOLE TO THE END OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CKMPA /D/ 12QUANTITY,HOLE,BRACE BOLT BRACE BOLT HOLE QUANTITY THE NUMBER OF BRACE BOLT HOLES PROVIDED. 1A MODE REPLY 0 CKMQD /D/ 05DIRECTION,HOLE,BORED BORED HOLE DIRECTION AN INDICATION OF THE DIRECTION THE HOLE IS BORED. SELECT REPLY CODE 10AA38 CKMRD 18TYPE,ROOF,FRAME FRAME ROOF TYPE INDICATES THE TYPE OF FRAME ROOF PROVIDED. SELECT REPLY CODE 10AH28 CKMSD /D/ 07FEATURE,GAINED GAINED FEATURE AN INDICATION OF WHETHER OR NOT A GAINED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CKMTA /D/ 12QUANTITY,SIDE,GAINED GAINED SIDE QUANTITY THE NUMBER OF GAINED SIDES PROVIDED. 1A MODE REPLY 0 CKMWD /D/ 19POSITION,SIDE SIDE POSITION THE POSITION OF ONE SIDE IN RELATION TO THE OTHER. SELECT REPLY CODE 10AK54 CKMXD /D/ 18TYPE,GAIN GAIN TYPE INDICATES THE TYPE OF GAIN PROVIDED ON THE ITEM. SELECT REPLY CODE 10AK54 CKMYD /D/ 07HOLE,BOLT,THROUGH THROUGH BOLT HOLE AN INDICATION OF WHETHER OR NOT A THROUGH BOLT HOLE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CKMZJ /D/ 04DISTANCE BETWEEN BOLT HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES THE CENTER TO CENTER DISTANCE BETWEEN THE BOLT HOLES. 2D AND 1B MODE REPLY21AA051AC20 CKNBJ /D/ 04DISTANCE,ROOF APEX TO FIRST HOLE CENTER ROOF APEX TO FIRST HOLE CENTER DISTANCE THE DISTANCE FROM THE ROOF APEX TO FIRST HOLE CENTER. 2D AND 1B MODE REPLY21AA051AC20 CKNCD /D/ 07HOLE,BOLT,ADDITIONAL ADDITIONAL BOLT HOLE AN INDICATION OF WHETHER OR NOT AN ADDITIONAL BOLT HOLE IS INCLUDED. SELECT REPLY CODE 10AA49 CKNDJ /D/ 04DIAMETER,HOLE,BRACE BOLT BRACE BOLT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BRACE BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CKNFG /D/ 19PURPOSE,HOLE,DRILLED DRILLED HOLE PURPOSE THE FUNCTION FOR WHICH THE DRILLED HOLE IS INTENDED. FULL TEXT WRITE-IN 0 CKNGG /D/ 19CHARACTERISTIC,PORTION,RABBETED RABBETED PORTION CHARACTERISTIC THE CHARACTERISTIC OF THE RABBETED PORTION OF THE ITEM. FULL TEXT WRITE-IN 0 CKNHD /D/ 07KIT,REPAIR REPAIR KIT AN INDICATION OF WHETHER OR NOT A REPAIR KIT IS INCLUDED. SELECT REPLY CODE 10AA49 CKNJD /D/ 07CABINET CABINET AN INDICATION OF WHETHER OR NOT A CABINET IS INCLUDED. SELECT REPLY CODE 10AA49 CKNKD /D/ 07FEATURE,DESIGN,ANGLE ANGLE DESIGN FEATURE AN INDICATION OF WHETHER OR NOT AN ANGLE DESIGN FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CKNLD /D/ 18TYPE,COMPRESSION,RETAINING RETAINING COMPRESSION TYPE INDICATES THE TYPE OF RETAINING COMPRESSION. SELECT REPLY CODE 10AJ70 CKNND /D/ 07ADJUSTABILITY,STAND STAND ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE STAND IS ADJUSTABLE. SELECT REPLY CODE 10AB00 CKNPD /D/ 01COLOR,STAND STAND COLOR THE HUE OR TINT OF THE STAND. SELECT REPLY CODE 10AD06 CKNQD 11METHOD,OPERATION,CHAIR CHAIR OPERATION METHOD THE MEANS BY WHICH THE CHAIR IS OPERATED. SELECT REPLY CODE 10AC58 CKNRD 18TYPE,LENS,CYLINDRICAL CYLINDRICAL LENS TYPE INDICATES THE TYPE OF CYLINDRICAL LENS/ES/ PROVIDED. SELECT REPLY CODE 10AM04 CKNSD 18TYPE FOR WHICH DESIGNED,OPERATION,SURFACING SURFACING OPERATION TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF SURFACING OPERATION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK95 CKNTD 18TYPE FOR WHICH DESIGNED,LENS LENS TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF LENS FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AM04 CKNWF /D/T10RANGE IN DIOPTERS,SURFACING,LENS LENS SURFACING RANGE IN DIOPTERS A MEASUREMENT OF THE LENS SURFACING LIMITS,EXPRESSED IN DIOPTERS. 1F MODE REPLY 0 CKNXD /D/ 07REGULATOR,THICKNESS/CURVE THICKNESS/CURVE REGULATOR AN INDICATION OF WHETHER OR NOT A THICKNESS AND CURVE REGULATOR IS INCLUDED. SELECT REPLY CODE 10AA49 CKNYD /D/ 07CHUCK,MAGNETIC MAGNETIC CHUCK AN INDICATION OF WHETHER OR NOT A MAGNETIC CHUCK IS INCLUDED. SELECT REPLY CODE 10AA49 CKNZD /D/ 07SYSTEM,COOLANT COOLANT SYSTEM AN INDICATION OF WHETHER OR NOT A COOLANT SYSTEM IS INCLUDED. SELECT REPLY CODE 10AA49 CKPBD /D/ 07TIP,TAPER,REPLACEABLE STANDARD REPLACEABLE STANDARD TAPER TIP AN INDICATION OF WHETHER OR NOT A REPLACEABLE STANDARD TAPER TIP IS INCLUDED. SELECT REPLY CODE 10AA49 CKPCD /D/ 07HANDLE,OPERATING,ADJUSTABLE ADJUSTABLE OPERATING HANDLE AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE OPERATING HANDLE IS INCLUDED. SELECT REPLY CODE 10AA49 CKPDD /D/ 07ARM,POLISHING,ADJUSTABLE ADJUSTABLE POLISHING ARM AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE POLISHING ARM IS INCLUDED. SELECT REPLY CODE 10AA49 CKPFD /D/ 07PAN,SURFACING,REMOVABLE REMOVABLE SURFACING PAN AN INDICATION OF WHETHER OR NOT A REMOVABLE SURFACING PAN IS INCLUDED. SELECT REPLY CODE 10AA49 CKPGD /D/ 07SWITCH,CONTROL,HANDGRIP HANDGRIP CONTROL SWITCH AN INDICATION OF WHETHER OR NOT A HANDGRIP CONTROL SWITCH IS INCLUDED. SELECT REPLY CODE 10AA49 CKPHD /D/ 07LEVER,LATCH LATCH LEVER AN INDICATION OF WHETHER OR NOT A LATCH LEVER IS INCLUDED. SELECT REPLY CODE 10AA49 CKPJD /D/ 07CONTROL,TIMING,AUTOMATIC AUTOMATIC TIMING CONTROL AN INDICATION OF WHETHER OR NOT AN AUTOMATIC TIMING CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 CKPKD /D/ 07PAN,REMOVABLE REMOVABLE PAN AN INDICATION OF WHETHER OR NOT A REMOVABLE PAN IS INCLUDED. SELECT REPLY CODE 10AA49 CKPLD /D/ 07SPACE BETWEEN PAN AND OUTER WALL,AIR AIR SPACE BETWEEN PAN AND OUTER WALL AN INDICATION OF WHETHER OR NOT AIR SPACE IS INCLUDED BETWEEN THE PAN AND OUTER WALL/S/. SELECT REPLY CODE 10AA49 CKPMA 12QUANTITY,POSITION,TEMP CONTROL SWITCH TEMP CONTROL SWITCH POSITION QUANTITY THE NUMBER OF INDEXED POSITIONS TO WHICH THE TEMPERATURE CONTROL SWITCH MAY BE MOVED. 1A MODE REPLY 0 CKPND /D/ 07TRAY,STAND,ATTACHED ATTACHED STAND TRAY AN INDICATION OF WHETHER OR NOT AN ATTACHED TRAY IS INCLUDED WITH THE STAND. SELECT REPLY CODE 10AA49 CKPPD 03DESIGNATION,FORMULATION FORMULATION DESIGNATION THE NOMENCLATURE BY WHICH THE FORMULA/E/ IS KNOWN OR IDENTIFIED. SELECT REPLY CODE 10AJ50 CKPQD /D/ 09MATERIAL,RIM,LENS LENS RIM MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LENS RIM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CKPRD /D/ 17SURFACE TREATMENT,RIM,LENS LENS RIM SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE LENS RIM SURFACE. SELECT REPLY CODE 10AD09 CKPSD 01COLOR,FRONT FRONT COLOR THE HUE OR TINT OF THE FRONT. SELECT REPLY CODE 10AD06 CKPTJ 04WIDTH,BRIDGE BRIDGE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BRIDGE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CKPWJ /D/ 04DIAMETER,INSIDE,EYE WIRE EYE WIRE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE EYE WIRE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CKPXJ 04DIAMETER,INSIDE,HORIZONTAL,MAXIMUM,EYE WIRE EYE WIRE MAXIMUM HORIZONTAL INSIDE DIAMETER THE MAXIMUM HORIZONTAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE EYE WIRE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CKPYJ 04DIAMETER,INSIDE,VERTICAL,MAXIMUM,EYE WIRE EYE WIRE MAXIMUM VERTICAL INSIDE DIAMETER THE MAXIMUM VERTICAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE EYE WIRE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CKPZJ 04DIAMETER,OPENING,CENTRAL CENTRAL OPENING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CENTRAL OPENING OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CKQBJ /D/ 04SIZE,DIAMETER,HORIZONTAL HORIZONTAL DIAMETER SIZE DESIGNATES THE SIZE OF THE ITEM BY THE HORIZONTAL DIAMETER. 1D AND 1B MODE REPLY11AA05 CKQCD /D/ 07CONTROL,HEAT,VARIABLE VARIABLE HEAT CONTROL AN INDICATION OF WHETHER OR NOT A VARIABLE HEAT CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 CKQDD /D/ 14SHAPE,CONE CONE SHAPE THE PHYSICAL CONFIGURATION OF THE CONE. SELECT REPLY CODE 10AD07 CKQFD 18TYPE,PIECE,END END PIECE TYPE INDICATES THE TYPE OF END PIECE PROVIDED. SELECT REPLY CODE 10AK84 CKQGD /D/ 07FEATURE,MARKED,HORIZONTAL/VERTICAL AXES HORIZONTAL/VERTICAL AXES MARKED FEATURE AN INDICATION OF WHETHER OR NOT A HORIZONTAL AND VERTICAL AXES MARKED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CKQHD /D/ 07TAB,THUMB,MARKED MARKED THUMB TAB AN INDICATION OF WHETHER OR NOT A MARKED THUMB TAB IS INCLUDED. SELECT REPLY CODE 10AA49 CKQJJ /D/ 04DIAMETER,EXPOSED AREA,PLAQUE PLAQUE EXPOSED AREA DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE EXPOSED AREA OF THE PLAQUE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CKQKD /D/ 19FIGURE,DISPOSED,PLAQUE DIAL PLAQUE DIAL DISPOSED FIGURE AN INDICATION OF THE FIGURE DISPOSED ON THE PLAQUE DIAL. SELECT REPLY CODE 10AB44 CKQLD /D/ 09MATERIAL,CHART CHART MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CHART IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CKQMJ /D/ 04LENGTH,CHART CHART LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CHART,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CKQND 18TYPE,CLOSURE,NOSE NOSE CLOSURE TYPE INDICATES THE TYPE OF NOSE CLOSURE PROVIDED. SELECT REPLY CODE 10AF52 CKQPD 09MATERIAL,FILLER,PRIMARY PRIMARY FILLER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF THE PRIMARY FILLER MATERIAL. SELECT REPLY CODE 10AF45 CKQQD 01COLOR,BURST BURST COLOR THE COLOR OF THE SMOKE CLOUD PRODUCED BY THE ITEM WHEN EXPLODED. SELECT REPLY CODE 10AD06 CKQRD 01COLOR,DYE LOAD DYE LOAD COLOR THE HUE OR TINT OF THE DYE PRODUCED BY THE ITEM. SELECT REPLY CODE 10AD06 CKQSA 19NUMBER,MODEL,BURSTER BURSTER MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE BURSTER. 1A MODE REPLY 0 CKQTA 19NUMBER,MODEL,WARHEAD WARHEAD MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE WARHEAD. 1A MODE REPLY 0 CKQWA 19NUMBER,MODEL,ROCKET MOTOR ROCKET MOTOR MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE ROCKET MOTOR. 1A MODE REPLY 0 CKQXJ A19WEAPON AND MODEL NUMBER FOR WHICH DESIGNED WEAPON AND MODEL NUMBER FOR WHICH DESIGNED AN INDICATION OF THE WEAPON(S) AND MODEL NUMBER(S) WITH WHICH THE ITEM IS DESIGNED TO FUNCTION. 1D AND 1A MODE REPLY13AF49 CKQYH /D/ 19CAPABILITY,HANDLING,INTELLIGENCE DATA INTELLIGENCE DATA HANDLING CAPABILITY THE INTELLIGENCE DATA THE ITEM IS CAPABLE OF HANDLING. 3D MODE REPLY 33AJ412AK274AC58 CKQZH 11METHOD,INDICATION INDICATION METHOD THE MEANS PROVIDED TO INDICATE DATA. 2D MODE REPLY 22AK273AJ12 CKRBJ A18TYPE AND QUANTITY,CONNECTION,NONELECTRICAL NONELECTRICAL CONNECTION TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF NONELECTRICAL CONNECTIONS. 1D AND 1A MODE REPLY12AB76 CKRCJ 13THREAD LENGTH,MAXIMUM MAXIMUM THREAD LENGTH A MEASUREMENT OF THE THREADS ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS. 1D AND 1B MODE REPLY11AA05 CKRDH /D/ 18TYPE AND LOCATION,ELEMENT,SENSING SENSING ELEMENT TYPE AND LOCATION INDICATES THE TYPE AND LOCATION OF THE SENSING ELEMENT. 2D MODE REPLY 23AJ773AJ91 CKRFD /D/ 11METHOD,OPERATION,LOCKING DEVICE LOCKING DEVICE OPERATION METHOD THE MEANS PROVIDED TO OPERATE THE LOCKING DEVICE. SELECT REPLY CODE 10AC58 CKRGJ 10SUCTION RATING,AIR AIR SUCTION RATING THE AMOUNT OF AIR SUCTION REQUIRED. 1D AND 1B MODE REPLY11AC43 CKRHJ 10FREQUENCY,MAINTAINED MAINTAINED FREQUENCY AN INDICATION OF THE FREQUENCY THE ITEM IS DESIGNED TO MAINTAIN. 1D AND 1B MODE REPLY13AK09 CKRJD /D/ 18TYPE,DEVICE,FREQUENCY FREQUENCY DEVICE TYPE INDICATES THE TYPE OF FREQUENCY DEVICE PROVIDED. SELECT REPLY CODE 10AK54 CKRKJ 10DEVIATION,FREQUENCY,MAXIMUM MAINTAINED MAXIMUM MAINTAINED FREQUENCY DEVIATION THE GREATEST DEVIATION IN FREQUENCY PERMISSIBLE IN THE OPERATION OF THE ITEM. 1D AND 1B MODE REPLY13AK09 CKRLG /D/ 19AGENCY AND IDENTIFYING NUMBER,CONTROLLING,DOCUMENT DOCUMENT CONTROLLING AGENCY AND IDENTIFYING NUMBER THE NAME OF THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DOCUMENT AND THE DOCUMENT NUMBER/S/. FULL TEXT WRITE-IN 0 CKRMD 11METHOD,OPERATION,INTEGRAL VALVE INTEGRAL VALVE OPERATION METHOD THE MEANS USED TO OPERATE THE INTEGRAL VALVE. SELECT REPLY CODE 10AC58 CKRNH /D/ 19CURRENT PER SECTION FOR WHICH DESIGNED,CIRCUIT CIRCUIT CURRENT PER SECTION FOR WHICH DESIGNED THE TYPE ELECTRICAL CIRCUIT PER SECTION FOR WHICH THE ITEM IS DESIGNED. 3D MODE REPLY 33AJ911AB621AC81 CKRPJ 10VOLTAGE RATING PER SECTION IN VOLTS,CONTINUOUS,NONDERATED NONDERATED CONTINUOUS VOLTAGE RATING PER SECTION IN VOLTS THE HIGHEST POTENTIAL PER SECTION THAT MAY BE CONTINUOUSLY APPLIED TO THE ITEM AT THE HIGHEST TEMPERATURE WITHOUT VOLTAGE DERATING. 1D AND 1B MODE REPLY13AJ91 CKRQJ /D/ 10VOLTAGE RATING PER SECTION IN VOLTS,CONTINUOUS,DERATED DERATED CONTINUOUS VOLTAGE RATING PER SECTION IN VOLTS THE HIGHEST POTENTIAL PER SECTION THAT MAY BE CONTINUOUSLY APPLIED TO THE ITEM AT ITS MAXIMUM OPERATING TEMPERATURE. 1D AND 1B MODE REPLY13AJ91 CKRRJ /D/T10RANGE PER SECTION,TEMP,OPERATING,NONDERATED NONDERATED OPERATING TEMP RANGE PER SECTION THE MINIMUM AND MAXIMUM LIMITS OF TEMPERATURE PER SECTION WITHIN WHICH THE ITEM MAY BE OPERATED WITHOUT VOLTAGE DERATING. 2D AND 1F MODE REPLY21AB363AJ91 CKRSJ /D/ 10TEMP PER SECTION AT WHICH DERATED VOLTAGE RATINGS APPLY,MAX MAX TEMP PER SECTION AT WHICH DERATED VOLTAGE RATINGS APPLY THE HIGHEST TEMPERATURE PER SECTION AT WHICH THE ITEM MAY BE OPERATED AT REDUCED VOLTAGE RATING. 2D AND 1B MODE REPLY21AB363AJ91 CKRTJ /D/ 10CURRENT RATING PER SECTION IN AMPS,ALTERNATING ALTERNATING CURRENT RATING PER SECTION IN AMPS THE ALTERNATING CURRENT RATING PER SECTION,EXPRESSED IN AMPERES. 1D AND 1B MODE REPLY13AJ91 CKRWJ /D/ 10FREQUENCY PER SECTION IN HERTZ FREQUENCY PER SECTION IN HERTZ THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT PER SECTION. 1D AND 1B MODE REPLY13AJ91 CKRXJ /D/ 10COEFFICIENT OF CAPACITANCE PER SECTION IN PPM PER DEG CELSIUS,TEMP TEMP COEFFICIENT OF CAPACITANCE PER SECTION IN PPM PER DEG CELSIUS A CONSTANT THAT REPRESENTS THE PROPORTIONATE CHANGE IN CAPACITANCE PER SECTION CAUSED BY A CHANGE IN TEMPERATURE,EXPRESSED IN PARTS PER MILLION PER DEGREE CELSIUS. 1D AND 1B MODE REPLY13AJ91 CKRYJ /D/T10TOLERANCE OF TEMP COEFFICIENT PER SECTION IN PPM PER DEG CELSIUS TOLERANCE OF TEMP COEFFICIENT PER SECTION IN PPM PER DEG CELSIUS THE LIMITS OF PERMISSIBLE DEVIATION OF THE TEMPERATURE COEFFICIENT PER SECTION FROM THE RATED VALUE,EXPRESSED IN PARTS PER MILLION PER DEGREE CELSIUS. 1D AND 1F MODE REPLY13AJ91 CKRZJ /D/T10COEFFICIENT OF CAPACITANCE RANGE PER SECTION IN PPM PER DEG CELSIUS,TEMP TEMP COEFFICIENT OF CAPACITANCE RANGE PER SECTION IN PPM PER DEG CELSIUS THE MINIMUM AND MAXIMUM VALUES OF PERMISSIBLE CHANGE IN CAPACITANCE PER SECTION CAUSED BY A CHANGE IN TEMPERATURE,EXPRESSED IN PARTS PER MILLION PER DEGREE CELSIUS. 1D AND 1F MODE REPLY13AJ91 CKSBH /D/ 19CHARACTERISTIC PER SECTION,TUNING TUNING CHARACTERISTIC PER SECTION THE TUNING CHARACTERISTIC PER SECTION OF THE ITEM. 2D MODE REPLY 22AM523AJ91 CKSCJ 10FREQUENCY,SPECIFIED,FURNISHED CRYSTAL UNIT FURNISHED CRYSTAL UNIT SPECIFIED FREQUENCY THE FREQUENCY AT WHICH THE FURNISHED CRYSTAL UNIT IS DESIGNED TO OPERATE UNDER SPECIFIC CONDITIONS. 1D AND 1B MODE REPLY12AJ20 CKSDH 19CHARACTERISTICS,DESIGN DESIGN CHARACTERISTICS AN INDICATION OF THE DESIGN CHARACTERISTICS OF THE ITEM. 2D MODE REPLY 21AA793AK54 CKSFL 16STYLE,END,FIRST PISTON ROD FIRST PISTON ROD END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FIRST PISTON ROD END. 1L MODE REPLY 0 CKSGD 13THREAD SERIES DESIGNATOR,END,FIRST PISTON ROD FIRST PISTON ROD END THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER ON THE FIRST PISTON ROD END. SELECT REPLY CODE 10AH06 CKSHJ 04THREAD DIAMETER,END,FIRST PISTON ROD FIRST PISTON ROD END THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FIRST PISTON ROD END WHICH WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD. 2D AND 1B MODE REPLY21AA051AC20 CKSJA 13THREAD QUANTITY PER INCH,END,FIRST PISTON ROD FIRST PISTON ROD END THREAD QUANTITY PER INCH THE NUMBER OF SCREW THREADS ON THE FIRST PISTON ROD END PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CKSKA 13THREAD CLASS,END,FIRST PISTON ROD FIRST PISTON ROD END THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD OF THE FIRST PISTON ROD END. 1A MODE REPLY 0 CKSLD /D/ 13THREAD DIRECTION,END,FIRST PISTON ROD FIRST PISTON ROD END THREAD DIRECTION THE DIRECTION OF THE FIRST PISTON ROD END THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 CKSMJ 13THREAD SIZE,PIPE,NOMINAL,FIRST PISTON ROD END FIRST PISTON ROD END NOMINAL PIPE THREAD SIZE THE INDUSTRIAL SIZE DESIGNATION USED TO INDICATE THE DIAMETER OF THE FIRST PISTON ROD END PIPE THREAD. 1D AND 1B MODE REPLY11AA05 CKSNJ 04LENGTH,SURFACE,RAISED RAISED SURFACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE RAISED SURFACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CKSPJ 04DIAMETER,SURFACE,RAISED RAISED SURFACE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A RAISED SURFACE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CKSQJ 04WIDTH,SURFACE,RAISED RAISED SURFACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A RAISED SURFACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CKSRJ 04HEIGHT,SURFACE,RAISED RAISED SURFACE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A RAISED SURFACE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CKSSD /D/ 07FEATURE,SURFACE,RAISED,CENTRALLY LOCATED CENTRALLY LOCATED RAISED SURFACE FEATURE AN INDICATION OF WHETHER OR NOT A CENTRALLY LOCATED RAISED SURFACE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CKSTG /D/ 19DIMENSION,BEVEL,CORNER CORNER BEVEL DIMENSION A MEASUREMENT OF THE DIMENSION OF THE CORNER BEVEL. FULL TEXT WRITE-IN 0 CKSWD /D/ 07APERTURE APERTURE AN INDICATION OF WHETHER OR NOT AN APERTURE IS INCLUDED. SELECT REPLY CODE 10AA49 CKSXD 14SHAPE,APERTURE APERTURE SHAPE THE PHYSICAL CONFIGURATION OF THE APERTURE. SELECT REPLY CODE 10AD07 CKSYJ 04RADIUS,CORNER,APERTURE APERTURE CORNER RADIUS A MEASUREMENT OF THE DISTANCE FROM THE CENTERLINE TO THE AXIS OF THE APERTURE CORNER. 2D AND 1B MODE REPLY21AA051AC20 CKSZG /D/ 19DIMENSION,BEVEL,APERTURE CORNER APERTURE CORNER BEVEL DIMENSION A MEASUREMENT OF THE DIMENSION OF THE APERTURE CORNER BEVEL. FULL TEXT WRITE-IN 0 CKTBD 18TYPE,APERTURE APERTURE TYPE INDICATES THE TYPE OF APERTURE PROVIDED. SELECT REPLY CODE 10AG79 CKTCJ /D/ 10WEIGHT PER ROLL WEIGHT PER ROLL THE WEIGHT OF THE ITEM WHEN SUPPLIED IN ROLL FORM. 1D AND 1B MODE REPLY12AG67 CKTDD 18TYPE,CORRUGATION CORRUGATION TYPE INDICATES THE TYPE OF CORRUGATION PROVIDED. SELECT REPLY CODE 10AK95 CKTFA /D/ 12QUANTITY PER INCH,CORRUGATION CORRUGATION QUANTITY PER INCH THE NUMBER OF CORRUGATIONS PER INCH. 1A MODE REPLY 0 CKTGA /D/ 12QUANTITY PER PIECE,CORRUGATION CORRUGATION QUANTITY PER PIECE THE NUMBER OF CORRUGATIONS PER PIECE. 1A MODE REPLY 0 CKTHJ 04LENGTH,OFFSET OFFSET LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CKTJA 12QUANTITY,SECTION,VIEWING VIEWING SECTION QUANTITY THE NUMBER OF VIEWING SECTIONS PROVIDED. 1A MODE REPLY 0 CKTKD /D/ 09MATERIAL,WINDOW,VIEWING UNIT VIEWING UNIT WINDOW MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE VIEWING UNIT WINDOW IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CKTLJ 04HEIGHT,OVERALL,VIEWING UNIT VIEWING UNIT OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE VIEWING UNIT. 2D AND 1B MODE REPLY21AA051AC20 CKTMJ 04WIDTH,OVERALL,VIEWING UNIT VIEWING UNIT OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE VIEWING UNIT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CKTNB /D/ 10TRANSMISSION RATING IN FOOT-LAMBERTS,LIGHT,CENTER,VIEWING UNIT VIEWING UNIT CENTER LIGHT TRANSMISSION RATING IN FOOT-LAMBERTS THE RATED AMOUNT OF LIGHT TRANSMITTED AT THE CENTER OF THE VIEWING UNIT,EXPRESSED IN FOOT-LAMBERTS. 1B MODE REPLY 0 CKTPD /D/ 07TRAY,DRIP DRIP TRAY AN INDICATION OF WHETHER OR NOT A DRIP TRAY IS INCLUDED. SELECT REPLY CODE 10AA49 CKTQD 11METHOD,ATTACHMENT,FILM FILM ATTACHMENT METHOD THE MEANS BY WHICH THE FILM IS ATTACHED TO THE ITEM. SELECT REPLY CODE 10AB47 CKTRD /D/ 07ASSEMBLY,MIRROR MIRROR ASSEMBLY AN INDICATION OF WHETHER OR NOT A MIRROR ASSEMBLY IS INCLUDED. SELECT REPLY CODE 10AA49 CKTSD /D/ 07ASSEMBLY,TRACK TRACK ASSEMBLY AN INDICATION OF WHETHER OR NOT A TRACK ASSEMBLY IS INCLUDED. SELECT REPLY CODE 10AA49 CKTTA 12QUANTITY,PRISM PRISM QUANTITY THE NUMBER OF PRISMS PROVIDED. 1A MODE REPLY 0 CKTWA 04SIZE ACCOMMODATED,FILM,MAXIMUM MAXIMUM FILM SIZE ACCOMMODATED DESIGNATES THE MAXIMUM FILM SIZE THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 CKTXJ 04LENGTH,TAB TAB LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TAB,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CKTYD /D/ 18TYPE,DIFFUSION DIFFUSION TYPE INDICATES THE TYPE OF DIFFUSION PROVIDED. SELECT REPLY CODE 10AD35 CKTZA 12QUANTITY,CAPABILITY,TEST TEST CAPABILITY QUANTITY THE NUMBER OF TESTS WHICH THE ITEM IS CAPABLE OF PERFORMING. 1A MODE REPLY 0 CKWBD 18TYPE,CUT,CORNER CORNER CUT TYPE INDICATES THE TYPE OF CUT ON THE CORNER/S/. SELECT REPLY CODE 10AL18 CKWCJ T10RANGE,SPEED,EMULSION EMULSION SPEED RANGE THE MINIMUM AND MAXIMUM SPEED OF THE EMULSION. 1D AND 1F MODE REPLY12AG67 CKWDD /D/ 07FEATURE,END,DRILLED FLANGE DRILLED FLANGE END FEATURE AN INDICATION OF WHETHER OR NOT A DRILLED FLANGE END FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CKWFD /D/ 09MATERIAL,PANEL,FRONT FRONT PANEL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FRONT PANEL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CKWGJ 04DISTANCE BETWEEN ARMS DISTANCE BETWEEN ARMS THE DISTANCE BETWEEN THE ARMS ON AN ITEM. 1D AND 1B MODE REPLY11AA05 CKWHD /D/ 07ARM,CURVED,UPWARD UPWARD CURVED ARM AN INDICATION OF WHETHER OR NOT AN UPWARD CURVED ARM/S/ IS PROVIDED. SELECT REPLY CODE 10AB22 CKWJA /D/ 12QUANTITY,SCREW SCREW QUANTITY THE NUMBER OF SCREWS PROVIDED. 1A MODE REPLY 0 CKWKJ /D/ 04LENGTH,OVERALL,SCREW SCREW OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE SCREW. 1D AND 1B MODE REPLY11AA05 CKWLD 18TYPE FOR WHICH DESIGNED,FILM FILM TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF FILM FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AG37 CKWMJ 04LENGTH,OVERALL,CROSSBAR CROSSBAR OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CROSSBAR. 1D AND 1B MODE REPLY11AA05 CKWNJ /D/ 04WIDTH,CHART CHART WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CHART,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CKWPJ /D/ 04LENGTH,OVERALL,CHART VIEWING SECTION CHART VIEWING SECTION OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CHART VIEWING SECTION. 1D AND 1B MODE REPLY11AA05 CKWQG /D/ 19CHARACTERISTIC,BRIGHTNESS,SUSTAINED,PLAQUE PLAQUE SUSTAINED BRIGHTNESS CHARACTERISTIC AN INDICATION OF THE SUSTAINED BRIGHTNESS CHARACTERISTIC/S/ OF THE PLAQUE. FULL TEXT WRITE-IN 0 CKWRJ /D/ 04WIDTH,OVERALL,CHART VIEWING SECTION CHART VIEWING SECTION OVERALL WIDTH THE OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CHART VIEWING SECTION. 1D AND 1B MODE REPLY11AA05 CKWSD /D/ 07FEATURE,MOUNTED,CHART ROLLER CHART ROLLER MOUNTED FEATURE AN INDICATION OF WHETHER OR NOT A CHART ROLLER MOUNTED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CKWTD /D/ 18TYPE FOR WHICH DESIGNED,TEST,CHART CHART TEST TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF TEST/S/ FOR WHICH THE CHART IS DESIGNED. SELECT REPLY CODE 10AK54 CKWWA /D/ 12QUANTITY,COLOR,TESTED TESTED COLOR QUANTITY THE NUMBER OF COLORS THE ITEM IS CAPABLE OF TESTING. 1A MODE REPLY 0 CKWXJ /D/T10RANGE,ADJUSTMENT,IRIS DIAPHRAGM IRIS DIAPHRAGM ADJUSTMENT RANGE THE MINIMUM AND MAXIMUM LIMITS TO WHICH THE IRIS DIAPHRAGM MAY BE ADJUSTED. 1D AND 1F MODE REPLY11AA05 CKWYJ /D/ 10UNIT,GRADUATION,IRIS DIAPHRAGM IRIS DIAPHRAGM GRADUATION UNIT THE INCREMENT OF MEASURE REPRESENTED BY THE MARKING/S/ ON THE IRIS DIAPHRAGM. 1D AND 1B MODE REPLY13AJ40 CKWZD /D/ 07CROSS,GREEK GREEK CROSS AN INDICATION OF WHETHER OR NOT A GREEK CROSS IS INCLUDED. SELECT REPLY CODE 10AA49 CKXBA 12QUANTITY,SLIDE,PROJECTION PROJECTION SLIDE QUANTITY THE NUMBER OF PROJECTION SLIDES INCLUDED WITH THE ITEM. 1A MODE REPLY 0 CKXCD 11METHOD,CONTROL,LIGHT LIGHT CONTROL METHOD THE MEANS BY WHICH THE LIGHT IS CONTROLLED. SELECT REPLY CODE 10AL37 CKXDD 14SHAPE,SCREEN SCREEN SHAPE THE PHYSICAL CONFIGURATION OF THE SCREEN. SELECT REPLY CODE 10AD07 CKXFD /D/ 07SECTION IN MILLIMETERS,RULED,HORIZONTALLY/VERTICALLY HORIZONTALLY/VERTICALLY RULED SECTION IN MILLIMETERS AN INDICATION OF WHETHER OR NOT A HORIZONTALLY AND VERTICALLY RULED SECTION IS INCLUDED,EXPRESSED IN MILLIMETERS. SELECT REPLY CODE 10AA49 CKXGD /D/ 07POLARIZER,INTEGRAL INTEGRAL POLARIZER AN INDICATION OF WHETHER OR NOT AN INTEGRAL POLARIZER IS INCLUDED. SELECT REPLY CODE 10AA49 CKXHD /D/ 07ANALYZER,POLAROID,INTEGRAL INTEGRAL POLAROID ANALYZER AN INDICATION OF WHETHER OR NOT AN INTEGRAL POLAROID ANALYZER IS INCLUDED. SELECT REPLY CODE 10AA49 CKXJD /D/ 18TYPE,SEGMENT/MAGNIFIER SEGMENT/MAGNIFIER TYPE INDICATES THE TYPE OF SEGMENT AND MAGNIFIER PROVIDED. SELECT REPLY CODE 10AK54 CKXKB /D/ 10INCREMENT IN DEG,SMALLEST SMALLEST INCREMENT IN DEG THE SMALLEST VALUE BETWEEN MARKINGS ON AN ITEM,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CKXLD 03DESIGNATION,SOLUTE SOLUTE DESIGNATION THE NAME BY WHICH A DISSOLVED SUBSTANCE IS KNOWN OR IDENTIFIED. SELECT REPLY CODE 10AG54 CKXMD 19GRADE,SOLUTE SOLUTE GRADE THE RECOGNIZED DESIGNATION INDICATING THE GRADE OR QUALITY OF THE SOLUTE. SELECT REPLY CODE 10AJ08 CKXNJ 10WEIGHT,SOLUTE SOLUTE WEIGHT THE QUANTITY OF SOLUTE PRESENT IN A SPECIFIED AMOUNT OF SOLUTION. 3D AND 1B MODE REPLY32AG671AC205AG54 CKXPJ 10PERCENTAGE,SOLUTE SOLUTE PERCENTAGE THE AMOUNT OF SOLUTE PRESENT IN A SOLUTION,EXPRESSED IN PERCENT. 3D AND 1B MODE REPLY32AL151AC205AG54 CKXQJ 10EQUIVALENT IN PERCENT,SOLUTE SOLUTE EQUIVALENT IN PERCENT THE SOLUTE AS MEASURED BY THE PERCENTAGE OF ITS CHEMICAL EQUIVALENT. 1D AND 1B MODE REPLY15AG54 CKXRG 10EQUIVALENT,COMPOUND COMPOUND EQUIVALENT A MEASUREMENT OF THE COMPOUND EQUIVALENT WHICH REPRESENTS THE ASSAY VALUE OF THE SOLUTE. FULL TEXT WRITE-IN 0 CKXSG /D/ 10EQUIVALENT,RADICAL,NEGATIVE NEGATIVE RADICAL EQUIVALENT A MEASUREMENT OF THE NEGATIVE RADICAL EQUIVALENT WHICH REPRESENTS THE VALUE OF THE SOLUTE. FULL TEXT WRITE-IN 0 CKXTG /D/ 19SPEC/STD,SOLUTE SOLUTE SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,CHEMICAL,OR SUBSTANCE OF THE SOLUTE. FULL TEXT WRITE-IN 0 CKXWG 19NAME,STANDARDIZED,COLOR COLOR STANDARDIZED NAME THE STANDARDIZED NAME OF THE COLOR OF THE ITEM. FULL TEXT WRITE-IN 0 CKXXA 19NUMBER,INDEX,COLOR COLOR INDEX NUMBER THE NUMBER USED TO IDENTIFY THE COLOR IN ACCORDANCE WITH A STANDARD. 1A MODE REPLY 0 CKXYD 03DESIGNATION,SOLVENT SOLVENT DESIGNATION THE NAME BY WHICH A SUBSTANCE,IN WHICH ANOTHER SUBSTANCE IS DISSOLVED,IS KNOWN OR IDENTIFIED. SELECT REPLY CODE 10AG54 CKXZD 19GRADE,SOLVENT SOLVENT GRADE THE RECOGNIZED DESIGNATION INDICATING THE GRADE OR QUALITY OF THE SOLVENT. SELECT REPLY CODE 10AJ08 CKYBJ 10PERCENTAGE,CONCENTRATION,SOLVENT SOLVENT CONCENTRATION PERCENTAGE THE CONCENTRATION OF THE SOLVENT,EXPRESSED IN PERCENT. 2D AND 1B MODE REPLY22AL155AG54 CKYCF T10RANGE,VALUE,PH,SOLUTION SOLUTION PH VALUE RANGE THE MINIMUM AND MAXIMUM LIMITS OF PH VALUES OF THE SOLUTION. 1F MODE REPLY 0 CKYDJ 10RANGE,ADJUSTMENT,PH PH ADJUSTMENT RANGE THE MINIMUM AND MAXIMUM ADJUSTMENTS OF THE PH SCALE. 1D AND 1B MODE REPLY11AC20 CKYFF T10RANGE DETERMINATION BY SOLUTION,PH PH RANGE DETERMINATION BY SOLUTION THE MINIMUM TO MAXIMUM LIMITS OF PH VALUES DETERMINED BY THE SOLUTION. 1F MODE REPLY 0 CKYGG 10VISCOSITY IN CENTIPOISES AT REFERENCE TEMP VISCOSITY IN CENTIPOISES AT REFERENCE TEMP THE ABSOLUTE UNITS (CENTIPOISES) OF THE ITEM AT A REFERENCE TEMPERATURE. FULL TEXT WRITE-IN 0 CKYHD 09MATERIAL,STABILIZER STABILIZER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF THE STABILIZER. SELECT REPLY CODE 10AG54 CKYJD 19CONTENTS,PACKAGE,UNIT UNIT PACKAGE CONTENTS THE SUBSTANCE,COMPOUND,OR MIXTURE CONTAINED IN THE UNIT PACKAGE. SELECT REPLY CODE 10AG54 CKYKD 19CHARACTERISTIC,COLOR COLOR CHARACTERISTIC AN INDICATION OF WHETHER OR NOT THE ITEM IS COLORED. SELECT REPLY CODE 10AG38 CKYLJ 10VALUE,INGREDIENT,ACTIVE ACTIVE INGREDIENT VALUE A MEASUREMENT OF THE ACTIVE INGREDIENT(S) OF THE ITEM. 2D AND 1B MODE REPLY23AJ405AG54 CKYMD 19GRADE,CHEMICAL CHEMICAL GRADE THE RECOGNIZED DESIGNATION INDICATING THE GRADE OR QUALITY OF THE CHEMICAL. SELECT REPLY CODE 10AJ08 CKYNJ 04DIAMETER AT DISTAL END,CUP CUP DIAMETER AT DISTAL END THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE DISTAL END OF A CUP,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CKYQD /D/ 07CATHETER CATHETER AN INDICATION OF WHETHER OR NOT A CATHETER IS PROVIDED. SELECT REPLY CODE 10AB22 CKYRD /D/ 18TYPE,CATHETER CATHETER TYPE INDICATES THE TYPE OF CATHETER PROVIDED. SELECT REPLY CODE 10AG24 CKYSJ 10CAPACITY,BAG BAG CAPACITY THE MEASURED CAPACITY OF THE BAG. 1D AND 1B MODE REPLY12AG67 CKYTD /D/ 09MATERIAL,CATHETER CATHETER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CATHETER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CKYWA 04SIZE,FRENCH,CATHETER CATHETER FRENCH SIZE THE NUMERIC DESIGNATION FOR THE FRENCH SIZE OF THE CATHETER. 1A MODE REPLY 0 CKYXD /D/ 03DESIGNATION,DESIGN,CATHETER CATHETER DESIGN DESIGNATION THE DESIGN DESIGNATION OF THE CATHETER. SELECT REPLY CODE 10AJ50 CKYYJ 04LENGTH,OVERALL,CATHETER CATHETER OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CATHETER. 2D AND 1B MODE REPLY21AA051AC20 CKYZD /D/ 09MATERIAL,SYRINGE SYRINGE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SYRINGE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CKZBD /D/ 09MATERIAL,TUBE,DRAINAGE DRAINAGE TUBE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE DRAINAGE TUBE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CKZCJ 04LENGTH,TUBE,DRAINAGE DRAINAGE TUBE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE DRAINAGE TUBE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CKZDD /D/ 09MATERIAL,BAG,DRAINAGE DRAINAGE BAG MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE DRAINAGE BAG IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CKZFJ /D/T10RANGE,GRADUATION,DRAINAGE BAG DRAINAGE BAG GRADUATION RANGE AN INDICATION OF THE GRADUATION RANGE OF THE DRAINAGE BAG. 1D AND 1F MODE REPLY12AG67 CKZGD /D/ 07HANGER,BEDSIDE,DRAINAGE BAG DRAINAGE BAG BEDSIDE HANGER AN INDICATION OF WHETHER OR NOT A DRAINAGE BAG BEDSIDE HANGER IS INCLUDED. SELECT REPLY CODE 10AA49 CKZHA 12QUANTITY,COMPARTMENT,TRAY TRAY COMPARTMENT QUANTITY THE NUMBER OF COMPARTMENTS FORMED BY PARTITIONS IN THE TRAY. 1A MODE REPLY 0 CKZJD /D/ 09MATERIAL,TRAY TRAY MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH A TRAY IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CKZKJ /D/ 04LENGTH,TRAY TRAY LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A TRAY,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CKZLD /D/ 09MATERIAL,DRAPE DRAPE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE DRAPE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CKZMD /D/ 07FEATURE,FENESTRATED FENESTRATED FEATURE AN INDICATION OF WHETHER OR NOT A FENESTRATED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CKZNJ /D/ 04LENGTH,DRAPE DRAPE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE DRAPE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CKZPJ /D/ 04WIDTH,DRAPE DRAPE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A DRAPE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CKZQA /D/ 12QUANTITY,BAR,SLIDE SLIDE BAR QUANTITY THE NUMBER OF SLIDE BARS PROVIDED. 1A MODE REPLY 0 CKZRD /D/ 09MATERIAL,BAR,SLIDE SLIDE BAR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SLIDE BAR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CKZSD /D/ 07FEATURE,COVER,PLASTIC LAMINATED PLASTIC LAMINATED COVER FEATURE AN INDICATION OF WHETHER OR NOT A PLASTIC LAMINATED COVER FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CKZTD /D/ 17SURFACE TREATMENT,BAR,SLIDE SLIDE BAR SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS THAT PROTECTS THE SLIDE BAR SURFACE. SELECT REPLY CODE 10AD09 CKZWD /D/ 01COLOR,BAR,SLIDE SLIDE BAR COLOR THE HUE OR TINT OF THE SLIDE BAR. SELECT REPLY CODE 10AD06 CKZXJ A03DESIGNATION AND QUANTITY,SIZE SIZE DESIGNATION AND QUANTITY DESIGNATES THE SIZE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED AND THE NUMBER FURNISHED. 1D AND 1A MODE REPLY13AF81 CKZYD /D/ 17SURFACE TREATMENT,HUB HUB SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE HUB SURFACE. SELECT REPLY CODE 10AD09 CKZZA 12QUANTITY,SYRINGE SYRINGE QUANTITY THE NUMBER OF SYRINGES PROVIDED. 1A MODE REPLY 0 CLASD /D/ 19CODE,CLASSIFICATION,SECURITY SECURITY CLASSIFICATION CODE THE CODE THAT INDICATES THE SECURITY CLASSIFICATION OF THE DESCRIPTION OF AN ITEM. SELECT REPLY CODE 10AE43 CLBBD /D/ 07RING,FINGER FINGER RING AN INDICATION OF WHETHER OR NOT A FINGER RING(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CLBCJ 04LENGTH,NEEDLE NEEDLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE NEEDLE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CLBDD /D/ 07BOX,NEEDLE NEEDLE BOX AN INDICATION OF WHETHER OR NOT A NEEDLE BOX IS PROVIDED. SELECT REPLY CODE 10AB22 CLBFA 12QUANTITY PER SET,UNIT UNIT QUANTITY PER SET THE NUMBER OF UNITS INCLUDED IN EACH SET. 1A MODE REPLY 0 CLBGJ 04LENGTH,OVERALL,CANNULA CANNULA OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CANNULA. 1D AND 1B MODE REPLY11AA05 CLBHJ 04SIZE,CANNULA CANNULA SIZE THE DESIGNATED SIZE BY WHICH THE CANNULA IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1D AND 1B MODE REPLY11AF98 CLBJD /D/ 07TIP,WHISTLE WHISTLE TIP AN INDICATION OF WHETHER OR NOT A WHISTLE TIP IS INCLUDED. SELECT REPLY CODE 10AA49 CLBKD /D/ 09MATERIAL,OBTURATOR OBTURATOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE OBTURATOR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CLBLJ 04LENGTH,OBTURATOR OBTURATOR LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE OBTURATOR,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CLBMJ 04DIAMETER,END,OBTURATOR PROXIMAL OBTURATOR PROXIMAL END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OBTURATOR PROXIMAL END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CLBND /D/ 19FLEXIBILITY,END,DISTAL DISTAL END FLEXIBILITY AN INDICATION OF THE FLEXIBILITY OF THE DISTAL END. SELECT REPLY CODE 10AD03 CLBPD /D/ 08LOCATION,OPENING,DISTAL END DISTAL END OPENING LOCATION INDICATES THE LOCATION OF THE OPENING ON THE DISTAL END. SELECT REPLY CODE 10AJ91 CLBQD /D/ 07STYLET STYLET AN INDICATION OF WHETHER OR NOT A STYLET IS INCLUDED. SELECT REPLY CODE 10AA49 CLBRD /D/ 07GRIP,THUMB-FOREFINGER THUMB-FOREFINGER GRIP AN INDICATION OF WHETHER OR NOT A THUMB AND FOREFINGER GRIP IS INCLUDED. SELECT REPLY CODE 10AA49 CLBSD 18TYPE,COMPONENT COMPONENT TYPE INDICATES THE TYPE OF COMPONENT PROVIDED. SELECT REPLY CODE 10AK95 CLBTJ 04SIZE,POINT POINT SIZE THE DESIGNATED SIZE BY WHICH THE POINT IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1D AND 1B MODE REPLY11AF98 CLBWJ /D/ 04WIDTH,OVERALL,POINT POINT OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE POINT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CLBXJ /D/ 04DIAMETER,INSIDE,BLADE BLADE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BLADE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CLBYD /D/ 14SHAPE,SHEATH SHEATH SHAPE THE PHYSICAL CONFIGURATION OF THE SHEATH. SELECT REPLY CODE 10AD07 CLBZD /D/ 07STUD,SOLDER SOLDER STUD AN INDICATION OF WHETHER OR NOT A SOLDER STUD IS INCLUDED. SELECT REPLY CODE 10AA49 CLCBA 03DESIGNATOR,SIZE,MATRIX RETAINER MATRIX RETAINER SIZE DESIGNATOR THE NUMBER ASSIGNED TO DESIGNATE THE SIZE OF THE MATRIX RETAINER. 1A MODE REPLY 0 CLCCD /D/ 07TIP,AFFIXED,PERMANENTLY PERMANENTLY AFFIXED TIP AN INDICATION OF WHETHER OR NOT A PERMANENTLY FIXED TIP/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CLCDJ 04LENGTH EXCLUDING TIP LENGTH EXCLUDING TIP A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM EXCLUDING THE TIP(S),IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CLCFJ /D/ 04SIZE,TIP,PROBE PROBE TIP SIZE THE DESIGNATED SIZE BY WHICH THE PROBE TIP IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1D AND 1B MODE REPLY11AF98 CLCGJ /D/ 04SIZE,TIP,STRIPPER STRIPPER TIP SIZE THE DESIGNATED SIZE BY WHICH THE STRIPPER TIP IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1D AND 1B MODE REPLY11AF98 CLCHJ 04LENGTH,OVERALL,BAND BAND OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BAND. 2D AND 1B MODE REPLY21AA051AC20 CLCJF T04DIAMETER RANGE IN MILLIMETERS DIAMETER RANGE IN MILLIMETERS THE MINIMUM AND MAXIMUM DIAMETER LIMITS,EXPRESSED IN MILLIMETERS. 1F MODE REPLY 0 CLCKD /D/ 07ROLL,CANVAS CANVAS ROLL AN INDICATION OF WHETHER OR NOT A CANVAS ROLL IS PROVIDED. SELECT REPLY CODE 10AB22 CLCMD /D/ 07FEATURE,OPERATED,ELECTRICALLY ELECTRICALLY OPERATED FEATURE AN INDICATION OF WHETHER OR NOT AN ELECTRICALLY OPERATED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CLCNA /D/ 12QUANTITY,NEEDLE,DISPLAYED DISPLAYED NEEDLE QUANTITY THE NUMBER OF NEEDLES DISPLAYED. 1A MODE REPLY 0 CLCPB 10WATTAGE RATING IN WATTS,INPUT INPUT WATTAGE RATING IN WATTS THE RATED POWER OF THE INPUT,MEASURED IN WATTS. 1B MODE REPLY 0 CLCQB 10FREQUENCY RATING IN MEGAHERTZ FREQUENCY RATING IN MEGAHERTZ THE NUMBER OF CYCLES PER SECOND FOR WHICH THE ITEM IS RATED,EXPRESSED IN MEGAHERTZ. 1B MODE REPLY 0 CLCRD /D/ 07INSERT,INTERCHANGEABLE INTERCHANGEABLE INSERT AN INDICATION OF WHETHER OR NOT AN INTERCHANGEABLE INSERT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CLCSJ 04LENGTH,TANK TANK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A TANK,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CLCTJ 04WIDTH,TANK TANK WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A TANK,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CLCWJ 04DIAMETER,TANK TANK DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A TANK,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CLCXJ 04DEPTH,TANK TANK DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON A TANK,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 CLCYA 12QUANTITY,CONTROL CONTROL QUANTITY THE NUMBER OF CONTROLS PROVIDED. 1A MODE REPLY 0 CLCZG /D/ 10RANGE,CONTROL,TIME TIME CONTROL RANGE A MEASUREMENT INDICATING THE TIME CONTROL LIMITS ON THE ITEM. FULL TEXT WRITE-IN 0 CLDBJ T10RANGE,TEMP,CONTROL CONTROL TEMP RANGE THE TEMPERATURE LIMITS OF THE CONTROL. 1D AND 1F MODE REPLY12AG67 CLDCG /D/ 19NAME AND QUANTITY,CONTROL CONTROL NAME AND QUANTITY THE NAME OF THE CONTROL(S) AND THE NUMBER OF EACH. FULL TEXT WRITE-IN 0 CLDDG /D/ 19NAME AND QUANTITY,FITTING FITTING NAME AND QUANTITY THE NAME OF THE FITTING(S) AND THE NUMBER OF EACH. FULL TEXT WRITE-IN 0 CLDFA 12QUANTITY ACCOMMODATED,FLASK FLASK QUANTITY ACCOMMODATED THE NUMBER OF FLASKS ACCOMMODATED BY THE ITEM. 1A MODE REPLY 0 CLDGD 18TYPE,CHAMBER,BREATHING BREATHING CHAMBER TYPE INDICATES THE TYPE OF BREATHING CHAMBER PROVIDED. SELECT REPLY CODE 10AL05 CLDHJ 04DIAMETER,INSIDE,BREATHING TUBE BREATHING TUBE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BREATHING TUBE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CLDJJ 04LENGTH,TUBE,BREATHING BREATHING TUBE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BREATHING TUBE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CLDKD /D/ 07UNIT,CHAMBER,MEASURED LITER MEASURED LITER CHAMBER UNIT AN INDICATION OF WHETHER OR NOT A MEASURED LITER CHAMBER UNIT IS INCLUDED. SELECT REPLY CODE 10AA49 CLDLJ /D/ 10CAPACITY,CHAMBER,SODA LIME SODA LIME CHAMBER CAPACITY THE CAPACITY OF THE SODA LIME CHAMBER. 1D AND 1B MODE REPLY12AG67 CLDMA 12QUANTITY,TEST,ROLL CHART ROLL CHART TEST QUANTITY THE NUMBER OF ROLL CHART TESTS. 1A MODE REPLY 0 CLDND /D/ 18TYPE,HYDRATION HYDRATION TYPE INDICATES THE TYPE OF HYDRATION PROVIDED. SELECT REPLY CODE 10AG36 CLDPG /D/ 19SPEC/STD,CHEMICAL CHEMICAL SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE CHEMICAL. FULL TEXT WRITE-IN 0 CLDQD /D/ 09MATERIAL,SOLVENT SOLVENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF THE SOLVENT. SELECT REPLY CODE 10AG54 CLDRJ /D/ 10PERCENTAGE,CONCENTRATION,SOLUTION SOLUTION CONCENTRATION PERCENTAGE THE PERCENTAGE OF THE SOLUTION CONCENTRATION. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. 2D AND 1B MODE REPLY22AL151AC20 CLDSJ 10PERCENTAGE,COMPOSITION COMPOSITION PERCENTAGE THE PERCENTAGE OF THE ELEMENT(S) USED IN THE COMPOSITION OF THE ITEM. 1D AND 1B MODE REPLY15AG54 CLDTJ 10TEMP RATING,POINT,SOFTENING SOFTENING POINT TEMP RATING THE TEMPERATURE AT WHICH A SUBSTANCE WILL SOFTEN. 2D AND 1B MODE REPLY23AJ401AC20 CLDWB 10PERCENTAGE,ASSAY,MINIMUM MINIMUM ASSAY PERCENTAGE THE PERCENTAGE OF THE MINIMUM WEIGHT OF THE ACTIVE CONSTITUENT. 1B MODE REPLY 0 CLDXJ 10TEMP RATING,POINT,BOILING BOILING POINT TEMP RATING THE TEMPERATURE AT WHICH A LIQUID BOILS. 1D AND 1B MODE REPLY13AJ40 CLDYJ /D/ 10TEMP RATING,TITER TITER TEMP RATING THE RATED TEMPERATURE OF AN ITEM AT WHICH TITRATION OCCURS. 1D AND 1B MODE REPLY13AJ40 CLDZB 10PERCENTAGE,CONTENT,UNSAPONIFIABLE,MAXIMUM MAXIMUM UNSAPONIFIABLE CONTENT PERCENTAGE THE PERCENTAGE OF THE MAXIMUM UNSAPONIFIABLE MATERIAL. 1B MODE REPLY 0 CLFBJ /D/ 10TEMP,INDEX,REFRACTION REFRACTION INDEX TEMP THE TEMPERATURE AT WHICH THE REFRACTION INDEX IS DETERMINED. 1D AND 1B MODE REPLY13AJ40 CLFCD 18TYPE,COMPOUND,ION EXCHANGE ION EXCHANGE COMPOUND TYPE INDICATES THE TYPE OF ION EXCHANGE COMPOUND PROVIDED. SELECT REPLY CODE 10AF11 CLFDD 19STANDARD,RATING RATING STANDARD THE STANDARD BY WHICH THE ITEM IS RATED. SELECT REPLY CODE 10AK54 CLFFA 19NUMBER,SAMPLE SAMPLE NUMBER THE IDENTIFYING NUMBER OF THE SAMPLE. 1A MODE REPLY 0 CLFGA 10CAPACITY PER CUBIC FOOT,EXCHANGE,GRAIN GRAIN EXCHANGE CAPACITY PER CUBIC FOOT THE GRAIN EXCHANGE CAPACITY PER CUBIC FOOT FOR WHICH THE ITEM IS RATED. 1A MODE REPLY 0 CLFHJ /D/ 10ADSORPTION PER GRAM,AMMONIA AMMONIA ADSORPTION PER GRAM A MEASUREMENT OF THE AMOUNT OF AMMONIA ADSORBED PER GRAM. 1D AND 1B MODE REPLY12AG67 CLFJF T04SIZE RANGE,PARTICLE,USS SIEVE USS SIEVE PARTICLE SIZE RANGE THE MINIMUM AND MAXIMUM SIZES OF THE PARTICLES AS RATED BY A US STANDARD. 1F MODE REPLY 0 CLFKA 12QUANTITY PER PACKAGE,COMPOUND,ION EXCHANGE ION EXCHANGE COMPOUND QUANTITY PER PACKAGE THE AMOUNT OF ION EXCHANGE COMPOUND CONTAINED IN A SINGLE PACKAGE. 1A MODE REPLY 0 CLFLD 18TYPE,EXCHANGE,RESINOUS COMPOUND RESINOUS COMPOUND EXCHANGE TYPE INDICATES THE TYPE OF EXCHANGE IN A RESINOUS COMPOUND. SELECT REPLY CODE 10AF11 CLFMD 18TYPE FOR WHICH DESIGNED,PLATFORM,BODY BODY PLATFORM TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF BODY PLATFORM FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AH86 CLFNB /D/ 10PERCENTAGE RETAINED ON LARGEST SCREEN,WEIGHT,MINIMUM MINIMUM WEIGHT PERCENTAGE RETAINED ON LARGEST SCREEN THE PERCENTAGE OF THE MINIMUM WEIGHT THE LARGEST SCREEN WILL RETAIN. 1B MODE REPLY 0 CLFPB /D/ 10WEIGHT PERCENTAGE PASSED THROUGH SMALLEST SCREEN,MAXIMUM MAXIMUM WEIGHT PERCENTAGE PASSED THROUGH SMALLEST SCREEN THE PERCENTAGE OF THE MAXIMUM WEIGHT THE SMALLEST SCREEN WILL PASS. 1B MODE REPLY 0 CLFQJ /D/ 04SIZE,SCREEN,RETAINING RETAINING SCREEN SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE RETAINING SCREEN. 1D AND 1B MODE REPLY11AA05 CLFRJ /D/ 04SIZE,SCREEN,PASSING PASSING SCREEN SIZE DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE PASSING SCREEN. 1D AND 1B MODE REPLY11AA05 CLFSB /D/ 10PERCENTAGE,CONTENT,FIXED CARBON,MINIMUM MINIMUM FIXED CARBON CONTENT PERCENTAGE THE PERCENTAGE OF THE MINIMUM FIXED CARBON CONTENT OF THE ITEM. 1B MODE REPLY 0 CLFTB 10PERCENTAGE BY WEIGHT,CONTENT,SULPHUR,MAXIMUM MAXIMUM SULPHUR CONTENT PERCENTAGE BY WEIGHT THE PERCENTAGE BY WEIGHT OF THE MAXIMUM SULPHUR CONTENT OF THE ITEM. 1B MODE REPLY 0 CLFWB /D/ 10PERCENTAGE,CONTENT,VOLATILE MATTER,MAXIMUM MAXIMUM VOLATILE MATTER CONTENT PERCENTAGE THE PERCENTAGE OF THE MAXIMUM VOLATILE MATTER CONTENT OF THE ITEM. 1B MODE REPLY 0 CLFXJ 10TIME IN MINUTES,BURNING,RATED RATED BURNING TIME IN MINUTES A MEASUREMENT OF THE RATED BURNING TIME OF THE ITEM,EXPRESSED IN MINUTES. 1D AND 1B MODE REPLY11AC20 CLFYG 10GRAVITY RATING AT SPECIFIED TEMP,AMERICAN PETROLEUM INSTITUTE AMERICAN PETROLEUM INSTITUTE GRAVITY RATING AT SPECIFIED TEMP AN INDICATION OF THE AMERICAN PETROLEUM INSTITUTE GRAVITY RATING AT A SPECIFIED TEMPERATURE. FULL TEXT WRITE-IN 0 CLFZJ 10TEMP,MAXIMUM,FREEZING POINT FREEZING POINT MAXIMUM TEMP AN INDICATION OF THE MAXIMUM TEMPERATURE AT WHICH THE ITEM WILL FREEZE. 1D AND 1B MODE REPLY13AJ40 CLGBA 19NUMBER,CLASSIFICATION,MINIMUM CETANE MINIMUM CETANE CLASSIFICATION NUMBER AN INDICATION OF THE MINIMUM CETANE CLASSIFICATION NUMBER OF THE ITEM. 1A MODE REPLY 0 CLGCJ 10TEMP,POINT,CLOUD,MAXIMUM MAXIMUM CLOUD POINT TEMP AN INDICATION OF THE MAXIMUM TEMPERATURE OF THE ITEM AT WHICH A CLOUD OR HAZE OF WAX CRYSTALS APPEAR WHEN THE ITEM IS COOLED. 1D AND 1B MODE REPLY13AJ40 CLGDG 19COMPOSITION,GENERAL GENERAL COMPOSITION AN INDICATION OF THE GENERAL COMPOSITION OF THE ITEM. FULL TEXT WRITE-IN 0 CLGFJ /D/ 10TEMP,POUR POINT,UPPER UPPER POUR POINT TEMP AN INDICATION OF THE UPPER POINT TEMPERATURE AT WHICH THE ITEM WILL POUR. 1D AND 1B MODE REPLY13AJ40 CLGGB 10TIME IN HOURS,TEST,MINIMUM BURNING MINIMUM BURNING TEST TIME IN HOURS AN INDICATION OF THE MINIMUM BURNING TEST TIME,EXPRESSED IN HOURS. 1B MODE REPLY 0 CLGHJ /D/ 10TEMP,END POINT,MAXIMUM MAXIMUM END POINT TEMP AN INDICATION OF THE MAXIMUM END POINT TEMPERATURE OF THE ITEM. 1D AND 1B MODE REPLY13AJ40 CLGJG /D/ 03DESIGNATION,COLOR,SAYBOLT SAYBOLT COLOR DESIGNATION THE SAYBOLT DESIGNATION BY WHICH THE COLOR IS IDENTIFIED. FULL TEXT WRITE-IN 0 CLGKA 19SYMBOL,MILITARY MILITARY SYMBOL THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MILITARY NUMBER. 1A MODE REPLY 0 CLGLJ 10TEMP,END POINT,DISTILLATION,MAXIMUM MAXIMUM DISTILLATION END POINT TEMP AN INDICATION OF THE MAXIMUM DISTILLATION END POINT TEMPERATURE. 1D AND 1B MODE REPLY13AJ40 CLGMJ T10RANGE,TEMP,TEN PERCENT EVAPORATION TEN PERCENT EVAPORATION TEMP RANGE THE MINIMUM AND MAXIMUM TEMPERATURES OF THE ITEM AT WHICH A TEN PERCENT EVAPORATION OCCURS. 1D AND 1F MODE REPLY13AJ40 CLGNJ 04LENGTH,INSIDE,WORKING CHAMBER WORKING CHAMBER INSIDE LENGTH A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF THE WORKING CHAMBER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CLGPJ 04HEIGHT,INSIDE,WORKING CHAMBER WORKING CHAMBER INSIDE HEIGHT AN INSIDE MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE WORKING CHAMBER,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CLGQJ 04WIDTH,INSIDE,WORKING CHAMBER WORKING CHAMBER INSIDE WIDTH AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE WORKING CHAMBER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CLGRD /D/ 07LEVER,CONTROL,PRESSURE PRESSURE CONTROL LEVER AN INDICATION OF WHETHER OR NOT A PRESSURE CONTROL LEVER IS PROVIDED. SELECT REPLY CODE 10AB22 CLGSD /D/ 07RESERVOIR,RECEIVING,WASTE WASTE RECEIVING RESERVOIR AN INDICATION OF WHETHER OR NOT A WASTE RECEIVING RESERVOIR IS PROVIDED. SELECT REPLY CODE 10AB22 CLGTD /D/ 07PYROMETER PYROMETER AN INDICATION OF WHETHER OR NOT A PYROMETER IS PROVIDED. SELECT REPLY CODE 10AB22 CLGWD /D/ 07END,RETRACTOR RETRACTOR END AN INDICATION OF WHETHER OR NOT A RETRACTOR END IS PROVIDED. SELECT REPLY CODE 10AB22 CLGXJ /D/ 04LENGTH,PORTION,CURVED RETRACTOR,END END CURVED RETRACTOR PORTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CURVED PORTION OF THE RETRACTOR END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CLGYD 01COLOR,FORM,PHYSICAL PHYSICAL FORM COLOR THE HUE OR TINT OF THE PHYSICAL FORM. SELECT REPLY CODE 10AD06 CLGZB 10PERCENTAGE,BASE,MEDICAMENT MEDICAMENT BASE PERCENTAGE THE PERCENTAGE OF MEDICAMENT BASE USED IN THE FABRICATION OF THE ITEM. 1B MODE REPLY 0 CLHBB 10PERCENTAGE,ADDITIVE,ABRASIVE ABRASIVE ADDITIVE PERCENTAGE THE PERCENTAGE OF ABRASIVE ADDITIVE USED IN THE FABRICATION OF THE ITEM. 1B MODE REPLY 0 CLHCJ 10PERCENTAGE,GRADUATION,SIEVE ABRASIVE PARTICLE SIZE SIEVE ABRASIVE PARTICLE SIZE GRADUATION PERCENTAGE THE PERCENTAGE OF ABRASIVE MATERIAL PASSING THROUGH A STANDARD SIEVE. 1D AND 1B MODE REPLY13AF81 CLHDJ 10TEMP RATING,CONSISTENCY,WORKABLE WORKABLE CONSISTENCY TEMP RATING THE TEMPERATURE AT WHICH THE ITEM IS AT ITS WORKABLE CONSISTENCY. 2D AND 1B MODE REPLY21AB361AC20 CLHFD /D/ 07END FOR ATTACHMENT TO DENTURE BASE,SHAPED SHAPED END FOR ATTACHMENT TO DENTURE BASE AN INDICATION OF WHETHER OR NOT THE END/S/ PROVIDED IS SHAPED FOR ATTACHMENT TO THE DENTURE BASE. SELECT REPLY CODE 10AB22 CLHGD 19NAME,SHADE SHADE NAME THE NOMENCLATURE BY WHICH THE SHADE IS IDENTIFIED. SELECT REPLY CODE 10AH62 CLHHD /D/ 07LIQUID LIQUID AN INDICATION OF WHETHER OR NOT A LIQUID IS INCLUDED. SELECT REPLY CODE 10AA49 CLHJD 18TYPE,PROCESS,CURING CURING PROCESS TYPE INDICATES THE PROCESS TYPE USED IN CURING THE ITEM. SELECT REPLY CODE 10AG42 CLHKD 18TYPE,BASE,HYDROCOLLOID HYDROCOLLOID BASE TYPE INDICATES THE TYPE OF HYDROCOLLOID BASE PROVIDED. SELECT REPLY CODE 10AF12 CLHLA /D/ 12QUANTITY,COLOR,INDIVIDUAL INDIVIDUAL COLOR QUANTITY THE NUMBER OF INDIVIDUAL COLORS PROVIDED. 1A MODE REPLY 0 CLHMD /D/ 11METHOD,RETENTION,WEDGE WEDGE RETENTION METHOD THE MEANS USED TO HOLD THE WEDGE IN PLACE. SELECT REPLY CODE 10AE36 CLHNJ 04HEIGHT ACCOMMODATED,FLASK FLASK HEIGHT ACCOMMODATED A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE FLASK THE ITEM IS DESIGNED TO ACCOMMODATE. 2D AND 1B MODE REPLY21AA051AC20 CLHPA /D/ 12QUANTITY,BASIN,MIXING MIXING BASIN QUANTITY THE NUMBER OF MIXING BASINS PROVIDED. 1A MODE REPLY 0 CLHQA /D/ 12QUANTITY,SLOT,BRUSH HOLDING BRUSH HOLDING SLOT QUANTITY THE NUMBER OF BRUSH HOLDING SLOTS PROVIDED. 1A MODE REPLY 0 CLHRA /D/ 12QUANTITY,COMPARTMENT,INDENTED MIXING SURFACE INDENTED MIXING SURFACE COMPARTMENT QUANTITY THE NUMBER OF INDENTED MIXING SURFACE COMPARTMENTS PROVIDED. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. 1A MODE REPLY 0 CLHSJ 04DEPTH,RECEPTACLE RECEPTACLE DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON A RECEPTACLE,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CLHTJ 04DIAMETER,RECEPTACLE RECEPTACLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A RECEPTACLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CLHWD /D/ 07DEPRESSION DEPRESSION AN INDICATION OF WHETHER OR NOT A DEPRESSION IS INCLUDED. SELECT REPLY CODE 10AA49 CLHXA 03DESIGNATION,SIZE,MATRIX RETAINER MATRIX RETAINER SIZE DESIGNATION A DESIGNATION INDICATING THE MATRIX RETAINER SIZE. 1A MODE REPLY 0 CLHYD /D/ 07HOOP,LIFTING LIFTING HOOP AN INDICATION OF WHETHER OR NOT A LIFTING HOOP IS INCLUDED. SELECT REPLY CODE 10AA49 CLHZD 11METHOD,DISCHARGE,WATER WATER DISCHARGE METHOD THE MEANS PROVIDED TO DISCHARGE THE WATER. SELECT REPLY CODE 10AM39 CLJBD /D/ 07VALVE,INTAKE INTAKE VALVE AN INDICATION OF WHETHER OR NOT AN INTAKE VALVE IS INCLUDED . SELECT REPLY CODE 10AA49 CLJCA 12QUANTITY ACCOMMODATED,SPOOL SPOOL QUANTITY ACCOMMODATED THE NUMBER OF SPOOLS THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 CLJDD /D/ 07PAD,RUBBER,NONSKID NONSKID RUBBER PAD AN INDICATION OF WHETHER OR NOT A NONSKID RUBBER PAD IS INCLUDED. SELECT REPLY CODE 10AA49 CLJFA /D/ 12QUANTITY ACCOMMODATED,STOOL STOOL QUANTITY ACCOMMODATED THE NUMBER OF STOOLS THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 CLJGD /D/ 07KIT,MOUNTING MOUNTING KIT AN INDICATION OF WHETHER OR NOT A MOUNTING KIT IS INCLUDED. SELECT REPLY CODE 10AA49 CLJHD /D/ 07CONTROL,FINGER,DISPENSING PREDETERMINED AMOUNT DISPENSING PREDETERMINED AMOUNT FINGER CONTROL AN INDICATION OF WHETHER OR NOT A FINGER CONTROL FOR DISPENSING A PREDETERMINED AMOUNT IS INCLUDED. SELECT REPLY CODE 10AA49 CLJJJ 04LENGTH,OVERALL,TOOTH TOOTH OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE TOOTH. 2D AND 1B MODE REPLY21AA051AC20 CLJKJ 04WIDTH,OVERALL,TOOTH TOOTH OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A TOOTH,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CLJLJ /D/ 04WIDTH,OVERALL,SIDE STRAP SIDE STRAP OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A SIDE STRAP,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CLJMJ 04DISTANCE ACROSS HEEL DISTANCE ACROSS HEEL THE DISTANCE ACROSS THE HEEL. 2D AND 1B MODE REPLY21AA051AC20 CLJND /D/ 18TYPE,POWER,AUTOMOTIVE,TIMING/RECORDING DEVICE TIMING/RECORDING DEVICE AUTOMOTIVE POWER TYPE INDICATES THE TYPE OF AUTOMOTIVE POWER PROVIDED ON THE TIMING AND RECORDING DEVICE. SELECT REPLY CODE 10AJ13 CLJPD /D/ 07DEVICE,TEMPLATE/CALCULATING TEMPLATE/CALCULATING DEVICE AN INDICATION OF WHETHER OR NOT A TEMPLATE AND/OR CALCULATING DEVICE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CLJQD /D/ 07CYLINDER,OXYGEN OXYGEN CYLINDER AN INDICATION OF WHETHER OR NOT AN OXYGEN CYLINDER IS INCLUDED. SELECT REPLY CODE 10AA49 CLJRJ T10RANGE,DOSAGE DOSAGE RANGE AN INDICATION OF THE DOSAGE RANGE OF THE ITEM. 1D AND 1F MODE REPLY12AG67 CLJSD /D/ 09MATERIAL,TIP,NOZZLE NOZZLE TIP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE NOZZLE TIP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CLJTD /D/ 09MATERIAL,INSERT,TIP ORIFICE TIP ORIFICE INSERT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TIP ORIFICE INSERT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CLJWD 19FUNCTION,CONTROL CONTROL FUNCTION AN INDICATION OF THE CONTROL FUNCTION OF THE ITEM. SELECT REPLY CODE 10AE74 CLJXJ 10PRESSURE,OPERATING,PUMP PUMP OPERATING PRESSURE THE OPERATING PRESSURE OF THE PUMP. 1D AND 1B MODE REPLY12AG67 CLJYD /D/ 07CONNECTION,COUPLING,QUICK DISCONNECT HYDRAULIC HOSE QUICK DISCONNECT HYDRAULIC HOSE COUPLING CONNECTION AN INDICATION OF WHETHER OR NOT A QUICK DISCONNECT HYDRAULIC HOSE COUPLING CONNECTION/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CLJZD /D/ 07HOLDER,BOTTLE BOTTLE HOLDER AN INDICATION OF WHETHER OR NOT A BOTTLE HOLDER IS INCLUDED. SELECT REPLY CODE 10AA49 CLKBD /D/ 07OUTFIT,CAUTERY CAUTERY OUTFIT AN INDICATION OF WHETHER OR NOT A CAUTERY OUTFIT IS INCLUDED. SELECT REPLY CODE 10AA49 CLKCD /D/ 07TESTER,PULP PULP TESTER AN INDICATION OF WHETHER OR NOT A PULP TESTER IS INCLUDED. SELECT REPLY CODE 10AA49 CLKDD /D/ 07ASPIRATOR,PUMP,VACUUM VACUUM PUMP ASPIRATOR AN INDICATION OF WHETHER OR NOT A VACUUM PUMP ASPIRATOR IS INCLUDED. SELECT REPLY CODE 10AA49 CLKFD /D/ 07HEATER,WATER WATER HEATER AN INDICATION OF WHETHER OR NOT A WATER HEATER IS INCLUDED. SELECT REPLY CODE 10AA49 CLKGD /D/ 07STRAINER/CLEANOUT,SUPPLY,WATER WATER SUPPLY STRAINER/CLEANOUT AN INDICATION OF WHETHER OR NOT A WATER SUPPLY STRAINER AND CLEANOUT IS INCLUDED. SELECT REPLY CODE 10AA49 CLKHD /D/ 07EJECTOR,SALIVA SALIVA EJECTOR AN INDICATION OF WHETHER OR NOT A SALIVA EJECTOR IS INCLUDED. SELECT REPLY CODE 10AA49 CLKJD /D/ 07APPARATUS,ADMINISTRATION,ETHER ETHER ADMINISTRATION APPARATUS AN INDICATION OF WHETHER OR NOT ETHER ADMINISTRATION APPARATUS IS INCLUDED. SELECT REPLY CODE 10AA49 CLKKD /D/ 07SOURCE,SUCTION,CONTROLLED CONTROLLED SUCTION SOURCE AN INDICATION OF WHETHER OR NOT A CONTROLLED SOURCE OF SUCTION IS INCLUDED. SELECT REPLY CODE 10AA49 CLKLB 10SUCTION PRODUCED IN MILLIMETERS OF MERCURY SUCTION PRODUCED IN MILLIMETERS OF MERCURY THE SUCTION PRODUCED,EXPRESSED IN MILLIMETERS OF MERCURY. 1B MODE REPLY 0 CLKMD /D/ 07FEATURE,TYPE,THERMOTIC THERMOTIC TYPE FEATURE AN INDICATION OF WHETHER OR NOT A THERMOTIC TYPE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CLKND 19PROTECTION,ENVIRONMENTAL,LINING LINING ENVIRONMENTAL PROTECTION THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT THE LINING IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY. SELECT REPLY CODE 10AA65 CLKPD /D/ 14SHAPE,CANISTER CANISTER SHAPE THE PHYSICAL CONFIGURATION OF THE CANISTER. SELECT REPLY CODE 10AD07 CLKQD /D/ 07MASK,ORONASAL ORONASAL MASK AN INDICATION OF WHETHER OR NOT AN ORONASAL MASK IS INCLUDED. SELECT REPLY CODE 10AA49 CLKRA /D/ 12QUANTITY,MASK,ORONASAL ORONASAL MASK QUANTITY THE NUMBER OF ORONASAL MASKS PROVIDED. 1A MODE REPLY 0 CLKSD /D/ 03DESIGNATION,SIZE,ORONASAL MASK ORONASAL MASK SIZE DESIGNATION A DESIGNATION IDENTIFYING THE SIZE OF THE ORONASAL MASK. SELECT REPLY CODE 10AF81 CLKTB /D/ 10CAPACITY IN LITERS,BAG,REBREATHING REBREATHING BAG CAPACITY IN LITERS AN INDICATION OF THE REBREATHING BAG CAPACITY,EXPRESSED IN LITERS. 1B MODE REPLY 0 CLKWD /D/ 07SUPPORT,MOUNTING,ADJUSTABLE ADJUSTABLE MOUNTING SUPPORT AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE MOUNTING SUPPORT IS INCLUDED. SELECT REPLY CODE 10AA49 CLKXA 12QUANTITY,CLIP,SUTURE SUTURE CLIP QUANTITY THE NUMBER OF SUTURE CLIPS PROVIDED. 1A MODE REPLY 0 CLKYD /D/ 09MATERIAL,CLIP,SUTURE SUTURE CLIP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SUTURE CLIPS(S) IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CLKZD /D/ 17SURFACE TREATMENT,SHANK SHANK SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A SHANK SURFACE. SELECT REPLY CODE 10AD09 CLLBA /D/ 12QUANTITY,FORCEPS,JAW ANGLE JAW ANGLE FORCEPS QUANTITY THE NUMBER OF FORCEPS PROVIDED ON THE JAW ANGLE. 1A MODE REPLY 0 CLLCD /D/ 02DESIGN,ANGLE,JAW JAW ANGLE DESIGN THE DESIGN OF THE JAW ANGLE. SELECT REPLY CODE 10AG26 CLLDA 12QUANTITY,STOPCOCK STOPCOCK QUANTITY THE NUMBER OF STOPCOCKS PROVIDED. 1A MODE REPLY 0 CLLFD /D/ 09MATERIAL,STOPCOCK STOPCOCK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE STOPCOCK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CLLGD /D/ 17SURFACE TREATMENT,STOPCOCK STOPCOCK SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE STOPCOCK SURFACE. SELECT REPLY CODE 10AD09 CLLHJ 04LENGTH,TUBING TUBING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TUBING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CLLJA /D/ 12QUANTITY,PLUG,NEEDLE NEEDLE PLUG QUANTITY THE NUMBER OF NEEDLE PLUGS PROVIDED. 1A MODE REPLY 0 CLLKD /D/ 07CONNECTOR,NEEDLE NEEDLE CONNECTOR AN INDICATION OF WHETHER OR NOT A NEEDLE CONNECTOR IS PROVIDED. SELECT REPLY CODE 10AB22 CLLLJ 04DIAMETER,END,FIRST,FILIFORM FILIFORM FIRST END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FIRST END OF A FILIFORM,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CLLMJ 04DIAMETER,CENTER,FILIFORM FILIFORM CENTER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CENTRAL PART OF A FILIFORM,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CLLND /D/ 07FACILITY,LUBRICATION,FIRST PISTON ROD END FIRST PISTON ROD END LUBRICATION FACILITY AN INDICATION OF WHETHER OR NOT A LUBRICATION FACILITY IS INCLUDED ON THE FIRST PISTON ROD END. SELECT REPLY CODE 10AA49 CLLPD 19SIMILARITY,END,PISTON ROD PISTON ROD END SIMILARITY AN INDICATION OF THE SIMILARITY OF THE PISTON ROD ENDS. SELECT REPLY CODE 10AA37 CLLQL 16STYLE,END,SECOND PISTON ROD SECOND PISTON ROD END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SECOND PISTON ROD END. 1L MODE REPLY 0 CLLRD 13THREAD SERIES DESIGNATOR,END,SECOND PISTON ROD SECOND PISTON ROD END THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER ON THE SECOND PISTON ROD END. SELECT REPLY CODE 10AH06 CLLSJ 04THREAD DIAMETER,END,SECOND PISTON ROD SECOND PISTON ROD END THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SECOND PISTON ROD END AND WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD. 2D AND 1B MODE REPLY21AA051AC20 CLLTA 13THREAD QUANTITY PER INCH,END,SECOND PISTON ROD SECOND PISTON ROD END THREAD QUANTITY PER INCH THE NUMBER OF SCREW THREADS ON THE SECOND PISTON ROD END PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CLLWA 13THREAD CLASS,END,SECOND PISTON ROD SECOND PISTON ROD END THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD ON THE SECOND PISTON ROD END. 1A MODE REPLY 0 CLLXD /D/ 13THREAD DIRECTION,END,SECOND PISTON ROD SECOND PISTON ROD END THREAD DIRECTION THE DIRECTION OF THE SECOND PISTON ROD END THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION,WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 CLLYJ 13THREAD SIZE,PIPE,NOMINAL,SECOND PISTON ROD END SECOND PISTON ROD END NOMINAL PIPE THREAD SIZE THE INDUSTRIAL SIZE DESIGNATION USED TO INDICATE THE DIAMETER OF THE SECOND PISTON ROD END PIPE THREAD. 1D AND 1B MODE REPLY11AA05 CLLZD /D/ 07FACILITY,LUBRICATION,SECOND PISTON ROD END SECOND PISTON ROD END LUBRICATION FACILITY AN INDICATION OF WHETHER OR NOT A LUBRICATION FACILITY IS INCLUDED ON THE SECOND PISTON ROD END. SELECT REPLY CODE 10AA49 CLMBJ 04DIAMETER,INSIDE,LARGEST,FIRST END FIRST END LARGEST INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CLMCJ 04DIAMETER,INSIDE,LARGEST,SECOND END SECOND END LARGEST INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CLMDJ 04WIDTH,FORK,FIRST END FIRST END FORK WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLMFJ 04WIDTH,FORK,SECOND END SECOND END FORK WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLMGJ 04DEPTH,FORK,FIRST END FIRST END FORK DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLMHJ 04DEPTH,FORK,SECOND END SECOND END FORK DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLMJJ 04WIDTH,SPAN,FIRST END FORK FIRST END FORK SPAN WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLMKJ 04WIDTH,SPAN,SECOND END FORK SECOND END FORK SPAN WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLMLH 18TYPE AND LOCATION,MOUNTING MOUNTING TYPE AND LOCATION INDICATES THE TYPE OF MOUNTING AND THE LOCATION ON THE ITEM. 2D MODE REPLY 23AM393AJ91 CLMNJ /D/ 04THREAD LENGTH,FACILITY,MOUNTING MOUNTING FACILITY THREAD LENGTH THE LENGTH OF THE THREADED PORTION OF THE MOUNTING FACILITY. 2D AND 1B MODE REPLY21AA051AC20 CLMPJ 13THREAD SIZE,PIPE,NOMINAL,MOUNTING FACILITY MOUNTING FACILITY NOMINAL PIPE THREAD SIZE THE INDUSTRIAL SIZE DESIGNATION USED TO INDICATE THE DIAMETER OF THE MOUNTING FACILITY PIPE THREAD. 1D AND 1B MODE REPLY11AA05 CLMQJ 04DIAMETER,FACILITY,MOUNTING MOUNTING FACILITY DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MOUNTING FACILITY,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CLMRJ 04DISTANCE BETWEEN MOUNTING PROVISIONS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING PROVISIONS NONE. 2D AND 1B MODE REPLY21AA051AC20 CLMSJ /D/A08LOCATION AND QUANTITY,PORT PORT LOCATION AND QUANTITY INDICATES THE LOCATION AND NUMBER OF PORTS ON THE ITEM. 1D AND 1A MODE REPLY13AJ91 CLMTL 16STYLE,PORT PORT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PORT. 1L MODE REPLY 0 CLMWD 13THREAD SERIES DESIGNATOR,PORT PORT THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER ON THE PORT. SELECT REPLY CODE 10AH06 CLMXJ 04THREAD DIAMETER,PORT PORT THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PORT AND WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD. 2D AND 1B MODE REPLY21AA051AC20 CLMYA 13THREAD QUANTITY PER INCH,PORT PORT THREAD QUANTITY PER INCH A MEASUREMENT OF THE NUMBER OF SCREW THREADS ON THE PORT PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CLMZJ 13THREAD SIZE,PIPE,NOMINAL,PORT PORT NOMINAL PIPE THREAD SIZE THE INDUSTRIAL SIZE DESIGNATION USED TO INDICATE THE DIAMETER OF THE PORT PIPE THREAD. 1D AND 1B MODE REPLY11AA05 CLNBA 13THREAD CLASS,PORT PORT THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL PORT THREAD. 1A MODE REPLY 0 CLNCJ 10ADJUSTMENT,MAXIMUM,ROD END ROD END MAXIMUM ADJUSTMENT A MEASUREMENT OF THE MAXIMUM ROD END ADJUSTMENT. 1D AND 1B MODE REPLY11AA05 CLNDA 12QUANTITY,FEATURE,BLEEDING BLEEDING FEATURE QUANTITY THE NUMBER OF BLEEDING FEATURES INCLUDED. 1A MODE REPLY 0 CLNFD 05DIRECTION,EXTENSION,PEDAL SHAFT PEDAL SHAFT EXTENSION DIRECTION AN INDICATION OF THE DIRECTION IN WHICH THE PEDAL SHAFT EXTENDS. SELECT REPLY CODE 10AM84 CLNGD 13THREAD SERIES DESIGNATOR,SWITCH,STOPLIGHT STOPLIGHT SWITCH THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF STOPLIGHT SWITCH SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CLNHJ 04THREAD DIAMETER,SWITCH,STOPLIGHT STOPLIGHT SWITCH THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A STOPLIGHT SWITCH AND WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD. 2D AND 1B MODE REPLY21AA051AC20 CLNJA /D/ 13THREAD CLASS,SWITCH,STOPLIGHT STOPLIGHT SWITCH THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL STOPLIGHT SWITCH. 1A MODE REPLY 0 CLNKA 13THREAD QUANTITY PER INCH,SWITCH,STOPLIGHT STOPLIGHT SWITCH THREAD QUANTITY PER INCH A MEASUREMENT OF THE NUMBER OF SCREW THREADS ON THE STOPLIGHT SWITCH PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CLNLD 13THREAD DIRECTION,SWITCH,STOPLIGHT STOPLIGHT SWITCH THREAD DIRECTION THE DIRECTION OF THE STOPLIGHT SWITCH THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 CLNMJ 13THREAD SIZE,PIPE,NOMINAL,STOPLIGHT SWITCH STOPLIGHT SWITCH NOMINAL PIPE THREAD SIZE THE INDUSTRIAL SIZE DESIGNATION USED TO INDICATE THE DIAMETER OF THE STOPLIGHT SWITCH PIPE THREAD. 1D AND 1B MODE REPLY11AA05 CLNND 10SPEED,RATED RATED SPEED THE SPEED FOR WHICH THE ITEM IS RATED. SELECT REPLY CODE 10AK03 CLNPD /D/ 09MATERIAL,HOLDER,SPOOL SPOOL HOLDER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SPOOL HOLDER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CLNQD /D/ 18TYPE,HOLDER,SPOOL SPOOL HOLDER TYPE INDICATES THE TYPE OF SPOOL HOLDER PROVIDED. SELECT REPLY CODE 10AK54 CLNRA 12QUANTITY,SCREEN,INTENSIFYING INTENSIFYING SCREEN QUANTITY THE NUMBER OF INTENSIFYING SCREENS PROVIDED. 1A MODE REPLY 0 CLNSA 12QUANTITY ACCOMMODATED QUANTITY ACCOMMODATED THE NUMBER OF OBJECTS THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 CLNTJ /D/ 04LENGTH,OVERALL,RECEPTIVE END RECEPTIVE END OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE RECEPTIVE END. 1D AND 1B MODE REPLY11AA05 CLNWJ /D/ 04HEIGHT,OVERALL,RECEPTIVE END RECEPTIVE END OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE RECEPTIVE END. 1D AND 1B MODE REPLY11AA05 CLNXJ /D/ 04THICKNESS,OVERALL,RECEPTIVE END RECEPTIVE END OVERALL THICKNESS AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF THE RECEPTIVE END,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 CLNYD /D/ 18TYPE,SPOOL SPOOL TYPE INDICATES THE TYPE OF SPOOL PROVIDED. SELECT REPLY CODE 10AK54 CLNZJ /D/ 04WIDTH,MAXIMUM,SPOOL SPOOL MAXIMUM WIDTH A MEASUREMENT OF THE MAXIMUM WIDTH OF THE SPOOL. 1D AND 1B MODE REPLY11AA05 CLPBJ /D/ 04WIDTH,MINIMUM,SPOOL SPOOL MINIMUM WIDTH A MEASUREMENT OF THE MINIMUM WIDTH OF THE SPOOL. 1D AND 1B MODE REPLY11AA05 CLPCJ 04DIAMETER,OUTSIDE,SPOOL SPOOL OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SPOOL,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CLPDD /D/ 09MATERIAL,SURFACE,WIPER WIPER SURFACE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WIPER SURFACE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CLPFJ /D/ 04WIDTH,SURFACE,WIPING WIPING SURFACE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE WIPING SURFACE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CLPGD 11METHOD,COOLING,TUBE TUBE COOLING METHOD THE MEANS OF COOLING USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE TUBE. SELECT REPLY CODE 10AN05 CLPHD 18TYPE,MOUNTING,TUBE TUBE MOUNTING TYPE INDICATES THE TYPE OF MOUNT UTILIZED TO SUPPORT THE TUBE. SELECT REPLY CODE 10AM39 CLPJD 18TYPE,ANODE,TUBE INSERT TUBE INSERT ANODE TYPE INDICATES THE TYPE OF TUBE INSERT ANODE PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AK95 CLPKJ 10VOLTAGE RATING,PEAK,TUBE INSERT FLUOROSCOPIC TUBE INSERT FLUOROSCOPIC PEAK VOLTAGE RATING THE MAXIMUM INSTANTANEOUS VOLTAGE FOR WHICH THE FLUOROSCOPIC TUBE INSERT IS RATED. 1D AND 1B MODE REPLY11AB63 CLPLJ 10VOLTAGE RATING,PEAK,TUBE INSERT RADIOGRAPHIC TUBE INSERT RADIOGRAPHIC PEAK VOLTAGE RATING THE MAXIMUM INSTANTANEOUS VOLTAGE FOR WHICH THE RADIOGRAPHIC TUBE INSERT IS RATED. 1D AND 1B MODE REPLY11AB63 CLPMJ 10CURRENT RATING,PEAK,RADIOGRAPHIC RADIOGRAPHIC PEAK CURRENT RATING THE MAXIMUM INSTANTANEOUS CURRENT WHICH FLOWS IN THE ITEM DURING A COMPLETE CYCLE. 1D AND 1B MODE REPLY11AC30 CLPNJ 10TIME RATING,EXPOSURE,RADIOGRAPHIC RADIOGRAPHIC EXPOSURE TIME RATING THE RATED TIME TO PRODUCE A RADIOGRAPH. 1D AND 1B MODE REPLY12AH68 CLPPA 12QUANTITY,SPOT,FOCAL FOCAL SPOT QUANTITY THE NUMBER OF FOCAL SPOTS PROVIDED. 1A MODE REPLY 0 CLPQG 04SIZE,SPOT,FOCAL FOCAL SPOT SIZE DESIGNATES THE SIZE OF THE FOCAL SPOT. FULL TEXT WRITE-IN 0 CLPRD 18TYPE,MOUNTING,TUBE STAND TUBE STAND MOUNTING TYPE INDICATES THE TYPE OF MOUNT UTILIZED TO SUPPORT THE TUBE STAND. SELECT REPLY CODE 10AM39 CLPSJ T04HEIGHT RANGE,FLOOR TO CEILING FLOOR TO CEILING HEIGHT RANGE THE MINIMUM AND MAXIMUM MEASUREMENT FROM THE FLOOR TO THE CEILING. 1D AND 1F MODE REPLY11AA05 CLPTG /D/ 10RANGE,TILT TILT RANGE THE MINIMUM AND MAXIMUM LIMITS OF TILT FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 CLPWD /D/ 07DIAPHRAGM,BUCKY BUCKY DIAPHRAGM AN INDICATION OF WHETHER OR NOT A BUCKY DIAPHRAGM IS INCLUDED. SELECT REPLY CODE 10AA49 CLPXD 18TYPE,TIMER,RADIOGRAPHIC RADIOGRAPHIC TIMER TYPE INDICATES THE TYPE OF RADIOGRAPHIC TIMER PROVIDED. SELECT REPLY CODE 10AK74 CLPYD 18TYPE,TIMER,FLUOROSCOPIC FLUOROSCOPIC TIMER TYPE INDICATES THE TYPE OF FLUOROSCOPIC TIMER PROVIDED. SELECT REPLY CODE 10AK74 CLPZJ /D/ 04LENGTH,UNIT,CONTROL CONTROL UNIT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CONTROL UNIT,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CLQBJ /D/ 04WIDTH,UNIT,CONTROL CONTROL UNIT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CONTROL UNIT,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CLQCJ /D/ 04HEIGHT,UNIT,CONTROL CONTROL UNIT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE CONTROL UNIT,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 CLQDD 11METHOD,RECTIFICATION,TRANSFORMER TRANSFORMER RECTIFICATION METHOD THE MEANS USED FOR RECTIFYING THE TRANSFORMER. SELECT REPLY CODE 10AK80 CLQFG 10CAPACITY,OUTPUT,TRANSFORMER TRANSFORMER OUTPUT CAPACITY THE POWER OUTPUT FOR WHICH THE TRANSFORMER IS RATED. FULL TEXT WRITE-IN 0 CLQGJ /D/ 04LENGTH,TRANSFORMER TRANSFORMER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A TRANSFORMER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CLQHJ /D/ 04WIDTH,TRANSFORMER TRANSFORMER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TRANSFORMER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CLQJJ /D/ 04HEIGHT,TRANSFORMER TRANSFORMER HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE TRANSFORMER,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CLQKA /D/ 12QUANTITY,TUBE,RECITIFIER RECITIFIER TUBE QUANTITY THE NUMBER OF RECTIFIER TUBES PROVIDED. 1A MODE REPLY 0 CLQLG 19NAME,COLLOQUIAL COLLOQUIAL NAME A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN. FULL TEXT WRITE-IN 0 CLQMJ 04HEIGHT,LOOP LOOP HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CLQNJ 04DIAMETER,END,SECOND,FILIFORM FILIFORM SECOND END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SECOND END OF A FILIFORM,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CLQPD /D/ 07FEATURE,CURRENT,BLENDED OUTPUT BLENDED OUTPUT CURRENT FEATURE AN INDICATION OF WHETHER OR NOT A BLENDED OUTPUT CURRENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CLQQA 12QUANTITY ACCOMMODATED,CYLINDER,STAND STAND CYLINDER QUANTITY ACCOMMODATED THE NUMBER OF CYLINDERS ACCOMMODATED IN THE STAND. 1A MODE REPLY 0 CLQRA 04SIZE ACCOMMODATED,CYLINDER,MAXIMUM MAXIMUM CYLINDER SIZE ACCOMMODATED DESIGNATES THE MAXIMUM CYLINDER SIZE THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 CLQSA 12QUANTITY,CASTER,STAND STAND CASTER QUANTITY THE NUMBER OF CASTERS PROVIDED ON THE STAND. 1A MODE REPLY 0 CLQTA 12QUANTITY,WHEEL,STAND STAND WHEEL QUANTITY THE NUMBER OF WHEELS PROVIDED ON THE STAND. 1A MODE REPLY 0 CLQWD 11METHOD,MOUNTING,GAS HEAD TO STAND GAS HEAD TO STAND MOUNTING METHOD THE MEANS BY WHICH THE GAS HEAD IS MOUNTED TO THE STAND. SELECT REPLY CODE 10AM39 CLQXJ 10ADJUSTMENT,VERTICAL VERTICAL ADJUSTMENT A MEASUREMENT OF THE VERTICAL ADJUSTMENT FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AA05 CLQYB /D/ 10ROTATION IN DEG,ADJUSTMENT,ROTARY ROTARY ADJUSTMENT ROTATION IN DEG A MEASUREMENT OF THE ROTATION OF THE ROTARY ADJUSTMENT,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CLQZA 12QUANTITY,FLOWMETER FLOWMETER QUANTITY THE NUMBER OF FLOWMETERS PROVIDED ON THE ITEM. 1A MODE REPLY 0 CLRBA 12QUANTITY,CHAMBER,ABSORPTION,CARBON DIOXIDE CARBON DIOXIDE ABSORPTION CHAMBER QUANTITY THE NUMBER OF CARBON DIOXIDE ABSORPTION CHAMBERS PROVIDED. 1A MODE REPLY 0 CLRCA 12QUANTITY,GAGE,PRESSURE PRESSURE GAGE QUANTITY THE NUMBER OF PRESSURE GAGES PROVIDED. 1A MODE REPLY 0 CLRDA 12QUANTITY,YOKE,SINGLE SINGLE YOKE QUANTITY THE NUMBER OF SINGLE YOKES PROVIDED. 1A MODE REPLY 0 CLRFA 12QUANTITY,YOKE,DOUBLE DOUBLE YOKE QUANTITY THE NUMBER OF DOUBLE YOKES PROVIDED. 1A MODE REPLY 0 CLRGD /D/ 07MANOMETER MANOMETER AN INDICATION OF WHETHER OR NOT A MANOMETER IS INCLUDED. SELECT REPLY CODE 10AA49 CLRHJ 04HEIGHT,TABLE TABLE HEIGHT A MEASUREMENT FORM THE BOTTOM TO THE TOP OF A TABLE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CLRJJ /D/ 04LENGTH,SHELF,EXTENSION EXTENSION SHELF LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN EXTENSION SHELF,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CLRKD /D/ 07EDGE ON TABLE/EXTENSION SHELF,SIDE,RAISED RAISED SIDE EDGE ON TABLE/EXTENSION SHELF AN INDICATION OF WHETHER OR NOT A RAISED SIDE EDGE/S/ IS PROVIDED ON THE TABLE AND/OR EXTENSION SHELF. SELECT REPLY CODE 10AB22 CLRLD /D/ 07SHELF,LOWER LOWER SHELF AN INDICATION OF WHETHER OR NOT A LOWER SHELF IS INCLUDED. SELECT REPLY CODE 10AA49 CLRMA /D/ 12QUANTITY,LEG,TABLE TABLE LEG QUANTITY THE NUMBER OF TABLE LEGS PROVIDED. 1A MODE REPLY 0 CLRND /D/ 09MATERIAL,MATTRESS MATTRESS MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MATTRESS IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CLRPD /D/ 07COVER,PROOF,MOISTURE MOISTURE PROOF COVER AN INDICATION OF WHETHER OR NOT A MOISTURE PROOF COVER IS PROVIDED. SELECT REPLY CODE 10AB22 CLRQD /D/ 14SHAPE,HOOD HOOD SHAPE THE PHYSICAL CONFIGURATION OF THE HOOD. SELECT REPLY CODE 10AD07 CLRRD /D/ 18TYPE,MOUNTING,HOOD HOOD MOUNTING TYPE INDICATES THE TYPE OF MOUNT UTILIZED TO SUPPORT THE HOOD. SELECT REPLY CODE 10AM39 CLRSJ 04LENGTH,HOOD HOOD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE HOOD,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CLRTJ 04HEIGHT,HOOD HOOD HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE HOOD,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CLRWA 12QUANTITY,DUCT,HOOD AIR HOOD AIR DUCT QUANTITY THE NUMBER OF AIR DUCTS PROVIDED ON THE HOOD. 1A MODE REPLY 0 CLRXA /D/ 12QUANTITY,CURTAIN,HOOD HOOD CURTAIN QUANTITY THE NUMBER OF CURTAINS PROVIDED IN THE HOOD. 1A MODE REPLY 0 CLRYG /D/ 03DESIGNATOR,SIZE,CURTAIN CURTAIN SIZE DESIGNATOR A DESIGNATION INDICATING THE SIZE BY WHICH THE CURTAIN IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. FULL TEXT WRITE-IN 0 CLRZG /D/ 19NAME AND QUANTITY,CONTROL,HEATING/AIR CIRCULATING UNIT HEATING/AIR CIRCULATING UNIT CONTROL NAME AND QUANTITY THE NAME AND NUMBER OF HEATING AND/OR AIR CIRCULATING UNIT CONTROLS PROVIDED. FULL TEXT WRITE-IN 0 CLSBD /D/ 07DISK,SEALED,FILTER UNIT FILTER UNIT SEALED DISK AN INDICATION OF WHETHER OR NOT A FILTER UNIT SEALED DISK IS PROVIDED. SELECT REPLY CODE 10AB22 CLSCD /D/ 07COVER,UNIT,REMOVABLE FILTER REMOVABLE FILTER UNIT COVER AN INDICATION OF WHETHER OR NOT A REMOVABLE FILTER UNIT COVER IS PROVIDED. SELECT REPLY CODE 10AB22 CLSDD 18TYPE,ELEMENT,FILTER FILTER ELEMENT TYPE INDICATES THE TYPE OF FILTER ELEMENT PROVIDED. SELECT REPLY CODE 10AL67 CLSFD /D/ 07COVER,TANK,REMOVABLE REMOVABLE TANK COVER AN INDICATION OF WHETHER OR NOT A REMOVABLE TANK COVER IS PROVIDED. SELECT REPLY CODE 10AB22 CLSHD 18TYPE,MATERIAL,SLING SLING MATERIAL TYPE INDICATES THE MATERIAL TYPE OF THE SLING. SELECT REPLY CODE 10AN48 CLSJJ 04LENGTH,MESH,NET NET MESH LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A NET MESH SPACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CLSKJ 04WIDTH,MESH,NET NET MESH WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A NET MESH SPACE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CLSLA /D/ 12QUANTITY,BURNER,STOVE STOVE BURNER QUANTITY THE NUMBER OF STOVE BURNERS PROVIDED. 1A MODE REPLY 0 CLSMJ /D/ 10CAPACITY,TANK,FUEL FUEL TANK CAPACITY THE CAPACITY OF FUEL THE TANK WILL HOLD. 1D AND 1B MODE REPLY12AG67 CLSNJ /D/T10RANGE,TEMP,BOILING POINT BOILING POINT TEMP RANGE THE MINIMUM AND MAXIMUM TEMPERATURES WHICH INDICATE THE BOILING POINT OF THE ITEM. 1D AND 1F MODE REPLY13AJ40 CLSPD /D/ 07DIMENSIONS,SUPPLEMENTAL,SHAFT END SHAFT END SUPPLEMENTAL DIMENSIONS AN INDICATION OF WHETHER OR NOT THE SHAFT END INCLUDES SUPPLEMENTAL DIMENSIONS. SELECT REPLY CODE 10AA49 CLSQJ /D/ 04DIAMETER,COMPLEMENT,MAJOR MAJOR COMPLEMENT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CLSRJ /D/ 04DISTANCE FROM END TO FLAT,MAJOR COMPLEMENT MAJOR COMPLEMENT DISTANCE FROM END TO FLAT NONE. 2D AND 1B MODE REPLY21AA051AC20 CLSSB /D/ 04ANGLE IN DEG,TAPER,MAJOR COMPLEMENT MAJOR COMPLEMENT TAPER ANGLE IN DEG NONE. 1B MODE REPLY 0 CLSTJ /D/ 04LENGTH,TAPER,MAJOR COMPLEMENT MAJOR COMPLEMENT TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLSWJ /D/ 04DEPTH,FLAT,MAJOR COMPLEMENT MAJOR COMPLEMENT FLAT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLSXJ /D/ 04LENGTH,FLAT,MAJOR COMPLEMENT MAJOR COMPLEMENT FLAT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLSYJ /D/ 04WIDTH,FLAT,MAJOR COMPLEMENT MAJOR COMPLEMENT FLAT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLSZJ /D/ 04WIDTH,GROOVE,MAJOR COMPLEMENT MAJOR COMPLEMENT GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLTBJ /D/ 04DIAMETER,GROOVE,MAJOR COMPLEMENT MAJOR COMPLEMENT GROOVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CLTCJ /D/ 04DISTANCE FROM END TO GROOVE,COMPLEMENT,MAJOR MAJOR COMPLEMENT DISTANCE FROM END TO GROOVE NONE. 2D AND 1B MODE REPLY21AA051AC20 CLTDG /D/ 04SIZE ACCOMMODATED,KEY,MAJOR COMPLEMENT MAJOR COMPLEMENT KEY SIZE ACCOMMODATED NONE. FULL TEXT WRITE-IN 0 CLTFJ /D/ 04WIDTH,KEYWAY,MAJOR COMPLEMENT MAJOR COMPLEMENT KEYWAY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLTGJ /D/ 04LENGTH,KEYWAY,MAJOR COMPLEMENT MAJOR COMPLEMENT KEYWAY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLTHJ /D/ 04DEPTH,KEYWAY,MAJOR COMPLEMENT MAJOR COMPLEMENT KEYWAY DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLTJJ /D/ 04DISTANCE FROM KEYWAY CENTER TO END,MAJOR COMPLEMENT MAJOR COMPLEMENT DISTANCE FROM KEYWAY CENTER TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 CLTKJ /D/ 04THICKNESS,TONGUE,MAJOR COMPLEMENT MAJOR COMPLEMENT TONGUE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CLTLJ /D/ 04LENGTH,TONGUE,MAJOR COMPLEMENT MAJOR COMPLEMENT TONGUE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLTMJ /D/ 04WIDTH,TONGUE,MAJOR COMPLEMENT MAJOR COMPLEMENT TONGUE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLTNA /D/ 12QUANTITY,SPLINE,MAJOR COMPLEMENT MAJOR COMPLEMENT SPLINE QUANTITY NONE. 1A MODE REPLY 0 CLTPJ /D/ 04LENGTH,SPLINE,MAJOR COMPLEMENT MAJOR COMPLEMENT SPLINE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLTQJ /D/ 04DIAMETER,MINOR,MAJOR COMPLEMENT SPLINE MAJOR COMPLEMENT SPLINE MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CLTRJ /D/ 04DIAMETER,MAJOR,MAJOR COMPLEMENT SPLINE MAJOR COMPLEMENT SPLINE MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CLTSJ /D/ 19DIMENSION,END,SQUARE,MAJOR COMPLEMENT MAJOR COMPLEMENT SQUARE END DIMENSION NONE. 2D AND 1B MODE REPLY21AA051AC20 CLTTJ /D/ 04LENGTH,END,SQUARE,MAJOR COMPLEMENT MAJOR COMPLEMENT SQUARE END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLTWJ /D/ 04DEPTH,SLOT,MAJOR COMPLEMENT MAJOR COMPLEMENT SLOT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLTXJ /D/ 04WIDTH,SLOT,MAJOR COMPLEMENT MAJOR COMPLEMENT SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLTYJ /D/ 04DIAMETER,HOLE,MAJOR COMPLEMENT MAJOR COMPLEMENT HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CLTZJ /D/ 04DISTANCE FROM HOLE CENTER TO END,MAJOR COMPLEMENT MAJOR COMPLEMENT DISTANCE FROM HOLE CENTER TO END NONE. 2D AND 1B MODE REPLY21AA051AC20 CLWBJ /D/ 13THREAD LENGTH,COMPLEMENT,MAJOR MAJOR COMPLEMENT THREAD LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLWCJ /D/ 04DEPTH,HOLE,MAJOR COMPLEMENT MAJOR COMPLEMENT HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLWDG /D/ 13THREAD DESIGNATION,INTERNAL,MAJOR COMPLEMENT MAJOR COMPLEMENT INTERNAL THREAD DESIGNATION NONE. FULL TEXT WRITE-IN 0 CLWFG /D/ 13THREAD DESIGNATION,EXTERNAL,MAJOR COMPLEMENT MAJOR COMPLEMENT EXTERNAL THREAD DESIGNATION NONE. FULL TEXT WRITE-IN 0 CLWGJ T10TEMP,GRAVITY,SPECIFIC SPECIFIC GRAVITY TEMP THE TEMPERATURE AT WHICH THE SPECIFIC GRAVITY RATIO IS DETERMINED. 1D AND 1F MODE REPLY13AJ40 CLWHD 19CLASSIFICATION,GRADE,FUEL FUEL GRADE CLASSIFICATION A CLASSIFICATION INDICATING THE RATED GRADE OF THE FUEL. SELECT REPLY CODE 10AF80 CLWJJ 10PRESSURE RATING,VAPOR,REID REID VAPOR PRESSURE RATING AN INDICATION OF THE ABSOLUTE VAPOR PRESSURE OF VOLATILE PETROLEUM PRODUCTS. 2D AND 1B MODE REPLY22AG671AC20 CLWKJ 10PRESSURE RATING AT WHICH DISTILLATION IS DETERMINED PRESSURE RATING AT WHICH DISTILLATION IS DETERMINED THE RATED PRESSURE AT WHICH THE DISTILLATION IS DETERMINED. 2D AND 1B MODE REPLY21AA051AC20 CLWLB 19NUMBER,OCTANE,MINIMUM,ASTM MOTOR METHOD ASTM MOTOR METHOD MINIMUM OCTANE NUMBER THE MINIMUM OCTANE NUMBER AS DETERMINED BY THE AMERICAN SOCIETY FOR TESTING MATERIALS MOTOR METHOD. 1B MODE REPLY 0 CLWMB 19NUMBER,OCTANE,MINIMUM,ASTM RESEARCH METHOD ASTM RESEARCH METHOD MINIMUM OCTANE NUMBER THE MINIMUM OCTANE NUMBER AS DETERMINED BY THE AMERICAN SOCIETY FOR TESTING MATERIALS RESEARCH METHOD. 1B MODE REPLY 0 CLWND /D/ 07ADDITIVE,ODORANT ODORANT ADDITIVE AN INDICATION OF WHETHER OR NOT AN ODORANT ADDITIVE IS INCLUDED. SELECT REPLY CODE 10AA49 CLWPJ /D/ 10PRESSURE AT 100 DEG FAHRENHEIT,VAPOR,MAXIMUM MAXIMUM VAPOR PRESSURE AT 100 DEG FAHRENHEIT THE MAXIMUM VAPOR PRESSURE,AT 100 DEGREES FAHRENHEIT,AT WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY12AG67 CLWQD 18TYPE,PRODUCT,GASIFIED GASIFIED PRODUCT TYPE INDICATES THE TYPE OF GASIFIED PRODUCT. SELECT REPLY CODE 10AB75 CLWRB 10PERCENTAGE BY VOLUME,OXYGEN,MINIMUM MINIMUM OXYGEN PERCENTAGE BY VOLUME A MEASUREMENT OF THE MINIMUM OXYGEN PERCENTAGE BY VOLUME. 1B MODE REPLY 0 CLWSG /D/ 10CONTENT AT SPECIFIED TEMP,MOISTURE,MAXIMUM MAXIMUM MOISTURE CONTENT AT SPECIFIED TEMP THE MAXIMUM MOISTURE CONTENT OF THE ITEM AT A SPECIFIED TEMPERATURE. FULL TEXT WRITE-IN 0 CLWTJ 10AMOUNT,SUPPLIED SUPPLIED AMOUNT A VALUE THAT INDICATES THE AMOUNT BY WHICH THE ITEM IS NORMALLY SUPPLIED. 1D AND 1B MODE REPLY12AG67 CLWWA 19NUMBER,STOCK,NATIONAL,CYLINDER CYLINDER NATIONAL STOCK NUMBER THE NATIONAL STOCK NUMBER ASSIGNED TO THE CYLINDER. 1A MODE REPLY 0 CLWXD /D/ 19CYLINDER,SUPPLIED SUPPLIED CYLINDER AN INDICATION OF WHETHER THE CYLINDER IS PART OF THE ITEM OF SUPPLY. SELECT REPLY CODE 10AK54 CLWYD /D/ 18TYPE,MATERIAL,SEALING MEDIUM SEALING MEDIUM MATERIAL TYPE INDICATES THE TYPE OF MATERIAL COMPOSING THE SEALING MEDIUM. SELECT REPLY CODE 10AN48 CLWZD /D/ 09MATERIAL,CAPSULE CAPSULE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CAPSULE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CLXBA /D/ 12QUANTITY ALONG WIDTH,HOLE,BOLT BOLT HOLE QUANTITY ALONG WIDTH NONE. 1A MODE REPLY 0 CLXCD /D/ 18TYPE,MATERIAL,SCRAP SCRAP MATERIAL TYPE INDICATES THE TYPE OF SCRAP MATERIAL. SELECT REPLY CODE 10AN48 CLXDG /D/ 19NUMBER AND NAME,GRADE GRADE NUMBER AND NAME THE COMBINED NUMBER AND NAME USED TO IDENTIFY THE GRADE OF AN ITEM. FULL TEXT WRITE-IN 0 CLXFD /D/ 07FEATURE,CHILLED CHILLED FEATURE AN INDICATION OF WHETHER OR NOT A CHILLED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CLXGD 07CHARACTERISTIC,FLAMMABILITY FLAMMABILITY CHARACTERISTIC AN INDICATION OF THE FLAMMABILITY CHARACTERISTIC OF THE ITEM. SELECT REPLY CODE 10AD43 CLXHD /D/ 07DISPENSER,GUN,HAND SPRAY HAND SPRAY GUN DISPENSER AN INDICATION OF WHETHER OR NOT A HAND SPRAY GUN DISPENSER IS INCLUDED. SELECT REPLY CODE 10AA49 CLXJB /D/ 10PERCENTAGE,INGREDIENT,ACTIVE ACTIVE INGREDIENT PERCENTAGE THE PERCENTAGE OF THE ACTIVE INGREDIENT IN THE ITEM. 1B MODE REPLY 0 CLXKD /D/ 07LOOP,WIRE WIRE LOOP AN INDICATION OF WHETHER OR NOT A WIRE LOOP IS INCLUDED. SELECT REPLY CODE 10AA49 CLXLG 19CHARACTERISTICS,DRYING DRYING CHARACTERISTICS THE CHARACTERISTICS REQUIRED FOR DRYING AN ITEM. FULL TEXT WRITE-IN 0 CLXMD 19INGREDIENT,LETHAL LETHAL INGREDIENT AN INDICATION OF THE LETHAL INGREDIENT CONTAINED IN THE ITEM. SELECT REPLY CODE 10AJ08 CLXNJ 10PERCENTAGE,INGREDIENT,LETHAL LETHAL INGREDIENT PERCENTAGE THE PERCENTAGE OF THE LETHAL INGREDIENT IN THE ITEM. 1D AND 1B MODE REPLY11AC20 CLXPG /D/ 10VALUE AND DOCUMENT NUMBER,STRENGTH STRENGTH VALUE AND DOCUMENT NUMBER AN INDICATION OF THE POTENCY OF THE ITEM AND THE DOCUMENT NUMBER WHICH ESTABLISHES THE VALUE. FULL TEXT WRITE-IN 0 CLXQD 18TYPE,ORGANISM,TEST TEST ORGANISM TYPE INDICATES THE TYPE OF ORGANISM TESTED. SELECT REPLY CODE 10AN57 CLXRG 10DILUTION BY VOLUME FOR TESTING DILUTION BY VOLUME FOR TESTING AN INDICATION OF THE DILUTION OF THE ITEM BY VOLUME FOR TESTING. FULL TEXT WRITE-IN 0 CLXSJ 10LIMIT,TIME,TEST TEST TIME LIMIT AN INDICATION OF THE TIME LIMIT OF THE TEST. 2D AND 1B MODE REPLY22AG671AC20 CLXTJ 10TEMP,TEST TEST TEMP THE NUMERIC VALUE THAT INDICATES THE TEMPERATURE AT WHICH THE ITEM IS TESTED. 1D AND 1B MODE REPLY13AJ40 CLXWB /D/ 04ANGLE IN DEG,CHAMFER,RIGHT END RIGHT END CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 CLXXB /D/ 04ANGLE IN DEG,CHAMFER,LEFT END LEFT END CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 CLXYB /D/ 04ANGLE IN DEG,CHAMFER,RIGHT PROJECTION RIGHT PROJECTION CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 CLXZB /D/ 04ANGLE IN DEG,CHAMFER,LEFT PROJECTION LEFT PROJECTION CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 CLYBJ 04DEPTH,CHAMFER,RIGHT END RIGHT END CHAMFER DEPTH NONE. REPLACED BY MRC AGHG WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 CLYCJ 04DEPTH,CHAMFER,LEFT END LEFT END CHAMFER DEPTH NONE. REPLACED BY MRC AGHG WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 CLYDJ 04DEPTH,CHAMFER,RIGHT PROJECTION RIGHT PROJECTION CHAMFER DEPTH NONE. REPLACED BY MRC AGHG WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 CLYFJ 04DEPTH,CHAMFER,LEFT PROJECTION LEFT PROJECTION CHAMFER DEPTH NONE. REPLACED BY MRC AGHG WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 CLYGG /D/ 18TYPE FOR WHICH DESIGNED,PLATE PLATE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF PLATE FOR WHICH THE ITEM IS DESIGNED. PLEASE USE MRC ARGW IN PLACE OF THIS CANCELED MRC. FULL TEXT WRITE-IN 0 CLYHJ 04WIDTH,GROOVE,SMALLER SMALLER GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CLYJJ 04RADIUS,GROOVE,SMALLER SMALLER GROOVE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CLYKJ 04DIAMETER,GROOVE,SMALLER SMALLER GROOVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CLYLJ 04HEIGHT ACCOMMODATED,ENVELOPE,MAXIMUM MAXIMUM ENVELOPE HEIGHT ACCOMMODATED THE MAXIMUM MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE ENVELOPE ACCOMMODATED. 1D AND 1B MODE REPLY11AA05 CLYMJ 04DISTANCE FROM END TO SMALLER GROOVE DISTANCE FROM END TO SMALLER GROOVE NONE. 2D AND 1B MODE REPLY21AA051AC20 CLYNA /D/ 12QUANTITY,HANDLE,SHELL SHELL HANDLE QUANTITY THE NUMBER OF HANDLES PROVIDED ON THE SHELL. 1A MODE REPLY 0 CLYPD /D/ 07COVER,REMOVABLE REMOVABLE COVER AN INDICATION OF WHETHER OR NOT A REMOVABLE COVER IS PROVIDED. SELECT REPLY CODE 10AB22 CLYQA /D/ 12QUANTITY,HANDLE,COVER COVER HANDLE QUANTITY THE NUMBER OF HANDLES PROVIDED ON THE COVER. 1A MODE REPLY 0 CLYRJ /D/ 04DIAMETER AND LOCATION,OUTSIDE,HUB END HUB END OUTSIDE DIAMETER AND LOCATION THE OUTSIDE DIAMETER AND LOCATION OF THE HUB END. PLEASE USE MRC ALNC WITH ISAC TBL 0368 IN PLACE OF THIS CANCELED MRC. 3D AND 1B MODE REPLY31AA051AC203AJ91 CLYSJ /D/ 04DISTANCE FROM OUTSIDE FLANGE/RIM TO HUB END AND LOCATION DISTANCE FROM OUTSIDE FLANGE/RIM TO HUB END AND LOCATION THE DISTANCE FROM THE OUTSIDE FLANGE OR RIM TO THE HUB END, AND ITS LOCATION. 3D AND 1B MODE REPLY31AA051AC203AJ91 CLYTD /D/ 07COVER,SELF-SEALING SELF-SEALING COVER AN INDICATION OF WHETHER OR NOT A SELF-SEALING COVER IS PROVIDED. SELECT REPLY CODE 10AB22 CLYWJ /D/ 10PRESSURE,OPERATING,AIR AIR OPERATING PRESSURE THE AIR PRESSURE AT WHICH AN ITEM IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY12AG67 CLYXJ /D/ 10PRESSURE,OPERATING,INTERNAL INTERNAL OPERATING PRESSURE THE NOMINAL FORCE PER UNIT OF AREA EXERTED OUTWARD FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY12AG67 CLYYJ /D/T10RANGE,PRESSURE,ACTUATED ACTUATED PRESSURE RANGE THE MINIMUM TO MAXIMUM ACTUATING PRESSURE AT WHICH AN ITEM IS DESIGNED TO OPERATE. 1D AND 1F MODE REPLY12AG67 CLYZB /D/ 10CAPACITY IN CUBIC CENTIMETERS CAPACITY IN CUBIC CENTIMETERS THE AMOUNT OF LIQUID,GRANULES,AND THE LIKE,THE ITEM WILL HOLD IN CUBIC CENTIMETERS. 1B MODE REPLY 0 CLZBD /D/ 09MATERIAL,STAND,MOUNTING MOUNTING STAND MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MOUNTING STAND IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CLZCD /D/ 07HOSE,OUTPUT OUTPUT HOSE AN INDICATION OF WHETHER OR NOT AN OUTPUT HOSE IS INCLUDED. SELECT REPLY CODE 10AA49 CLZDA 12QUANTITY,HANDPIECE HANDPIECE QUANTITY THE NUMBER OF HANDPIECES PROVIDED. 1A MODE REPLY 0 CLZFB 10RPM,HANDPIECE HANDPIECE RPM THE SPEED OF THE HANDPIECE EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 CLZGA 12QUANTITY,SINK SINK QUANTITY THE NUMBER OF SINKS PROVIDED. 1A MODE REPLY 0 CLZHJ 04LENGTH,OVERALL,INDIVIDUAL SINK INDIVIDUAL SINK OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF EACH SINK. 1D AND 1B MODE REPLY11AA05 CLZJJ 04WIDTH,OVERALL,INDIVIDUAL SINK INDIVIDUAL SINK OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF EACH SINK,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CLZKJ 04DEPTH,OVERALL,INDIVIDUAL SINK INDIVIDUAL SINK OVERALL DEPTH AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS ON EACH SINK,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 CLZLD 18TYPE,CONTROL,SINK WATER FAUCET SINK WATER FAUCET CONTROL TYPE INDICATES THE TYPE OF WATER FAUCET CONTROL PROVIDED FOR THE SINK. SELECT REPLY CODE 10AL37 CLZMJ 10CAPACITY,TANK,COLD WATER COLD WATER TANK CAPACITY THE CAPACITY OF THE COLD WATER TANK. 1D AND 1B MODE REPLY12AG67 CLZNJ 10CAPACITY,BOILER,HOT WATER HOT WATER BOILER CAPACITY THE CAPACITY OF THE HOT WATER BOILER. 1D AND 1B MODE REPLY12AG67 CLZPD /D/ 07GROMMET,CENTER CENTER GROMMET AN INDICATION OF WHETHER OR NOT A CENTER GROMMET IS INCLUDED. SELECT REPLY CODE 10AA49 CLZQD /D/ 09MATERIAL,GROMMET GROMMET MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH A GROMMET IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CLZRJ 04DIAMETER,INSIDE,BAND BAND INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BAND,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CLZSJ 04LENGTH,STRIP STRIP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A STRIP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CLZWD /D/ 09MATERIAL,MANDREL MANDREL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MANDREL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CLZXD /D/ 17SURFACE TREATMENT,MANDREL MANDREL SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE MANDREL SURFACE. SELECT REPLY CODE 10AD09 CLZYA /D/ 12QUANTITY,MANDREL MANDREL QUANTITY THE NUMBER OF MANDRELS PROVIDED. 1A MODE REPLY 0 CLZZJ /D/ 04LENGTH,OVERALL,MANDREL MANDREL OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE MANDREL. 2D AND 1B MODE REPLY21AA051AC20 CMATD /D/ 09COMPOSITE MATERIAL COMPOSITE MATERIAL THE PARTICULAR COMBINATION OF BINDER AND REINFORCEMENT ELEMENTS, FIBERS, CHEMICAL COMPOUNDS OR MECHANICAL MIXTURES THAT MAKE UP THE FINAL MATERIAL. SELECT REPLY CODE 10AD09 CMBBJ /D/ 04LENGTH,SHANK,MANDREL MANDREL SHANK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A MANDREL SHANK,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CMBCJ /D/ 04DIAMETER,SHANK,MANDREL MANDREL SHANK DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MANDREL SHANK,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CMBDD /D/ 09MATERIAL,ARBOR ARBOR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ARBOR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMBFD /D/ 17SURFACE TREATMENT,ARBOR ARBOR SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE ARBOR SURFACE. SELECT REPLY CODE 10AD09 CMBGJ 04LENGTH,OVERALL,ARBOR ARBOR OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ARBOR. 2D AND 1B MODE REPLY21AA051AC20 CMBHJ 04DIAMETER,SHANK,ARBOR ARBOR SHANK DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ARBOR SHANK,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CMBJA 12QUANTITY,ARBOR ARBOR QUANTITY THE NUMBER OF ARBORS PROVIDED. 1A MODE REPLY 0 CMBKJ 04SIZE,ARBOR ARBOR SIZE DESIGNATES THE SIZE OF THE ARBOR. 1D AND 1B MODE REPLY11AA05 CMBLD /D/ 07SCREW,ARBOR ARBOR SCREW AN INDICATION OF WHETHER OR NOT AN ARBOR SCREW IS INCLUDED. SELECT REPLY CODE 10AA49 CMBMJ 04LENGTH,OVERALL,SLEEVE SLEEVE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE SLEEVE. 2D AND 1B MODE REPLY21AA051AC20 CMBNB /D/ 19NUMBER,OCTANE,LEAN MIXTURE LEAN MIXTURE OCTANE NUMBER AN INDICATION OF THE LEAN MIXTURE OCTANE NUMBER. 1B MODE REPLY 0 CMBPB /D/ 19NUMBER,OCTANE,RICH MIXTURE RICH MIXTURE OCTANE NUMBER AN INDICATION OF THE RICH MIXTURE OCTANE NUMBER. 1B MODE REPLY 0 CMBQJ /D/T10RANGE,TEMP,FIFTY PERCENT EVAPORATION FIFTY PERCENT EVAPORATION TEMP RANGE THE MINIMUM AND MAXIMUM TEMPERATURES OF THE ITEM AT WHICH A FIFTY PERCENT EVAPORATION OCCURS. 1D AND 1F MODE REPLY13AJ40 CMBRJ /D/T10RANGE,TEMP,NINETY PERCENT EVAPORATION NINETY PERCENT EVAPORATION TEMP RANGE THE MINIMUM AND MAXIMUM TEMPERATURES OF THE ITEM AT WHICH A NINETY PERCENT EVAPORATION OCCURS. 1D AND 1F MODE REPLY13AJ40 CMBSB /D/ 10TETRAETHYL LEAD ALLOWABLE IN MILLILITERS PER GALLON,MAXIMUM MAXIMUM TETRAETHYL LEAD ALLOWABLE IN MILLILITERS PER GALLON A MEASUREMENT OF THE MAXIMUM TETRAETHYL LEAD ALLOWABLE PER GALLON,EXPRESSED IN MILLILITERS. 1B MODE REPLY 0 CMBTG /D/ 19MISSILE FOR WHICH DESIGNED MISSILE FOR WHICH DESIGNED AN INDICATION OF THE MISSILE FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 CMBWD 19INGREDIENTS,COMPOSITION COMPOSITION INGREDIENTS THE ELEMENTS,COMPOUNDS,OR MIXTURES OF THE COMPOSITION. SELECT REPLY CODE 10AG54 CMBXJ 10INGREDIENTS PER UNIT,ACTIVE ACTIVE INGREDIENTS PER UNIT THE AMOUNT OF ACTIVE INGREDIENTS CONTAINED IN EACH UNIT. 2D AND 1B MODE REPLY22AG673AJ40 CMBYA 12QUANTITY,VALUED,SERUM CONSTITUENTS SERUM CONSTITUENTS VALUED QUANTITY AN INDICATION OF THE NUMBER OF SERUM CONSTITUENTS VALUED. 1A MODE REPLY 0 CMBZD /D/ 19INGREDIENT,ADDITIONAL ADDITIONAL INGREDIENT A CHEMICAL OR SUBSTANCE WHICH IS ADDED TO OR MIXED WITH THE BASIC INGREDIENT. SELECT REPLY CODE 10AG54 CMCBD 19AGENT,DILUTING DILUTING AGENT THE SUBSTANCE OF WHICH THE DILUENT IS COMPOSED. SELECT REPLY CODE 10AG54 CMCCB /D/ 10EQUIVALENT IN MILLIGRAMS PER CAPSULE,CHEMICAL CHEMICAL EQUIVALENT IN MILLIGRAMS PER CAPSULE A MEASUREMENT OF THE CHEMICAL EQUIVALENT,EXPRESSED IN MILLIGRAMS PER CAPSULE. 1B MODE REPLY 0 CMCDJ /D/ 10AMOUNT,DILUENT DILUENT AMOUNT AN INDICATION OF THE AMOUNT OF DILUTING AGENT PROVIDED. 1D AND 1B MODE REPLY12AG67 CMCFD /D/ 07DILUENT,BUFFERED BUFFERED DILUENT AN INDICATION OF WHETHER OR NOT A BUFFERED DILUENT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CMCGD /D/ 19CONDITION,VIRUS VIRUS CONDITION AN INDICATION OF THE STATE OF THE VIRUS. SELECT REPLY CODE 10AK54 CMCHD 03DESIGNATION,ORGANISM ORGANISM DESIGNATION THE TERMINOLOGY BY WHICH AN ORGANISM IS KNOWN OR IDENTIFIED. SELECT REPLY CODE 10AG54 CMCJA /D/ 03DESIGNATOR,SEROTYPE SEROTYPE DESIGNATOR A NUMERIC AND/OR ALPHA SYMBOL REPRESENTING THE SEROTYPE. 1A MODE REPLY 0 CMCKD /D/ 07DILUTION DILUTION AN INDICATION OF WHETHER OR NOT DILUTION IS REQUIRED. SELECT REPLY CODE 10AE40 CMCLD /D/ 18TYPE,VIRUS VIRUS TYPE INDICATES THE TYPE OF VIRUS. SELECT REPLY CODE 10AJ46 CMCMJ /D/ 10VOLUME DELIVERED PER DROP VOLUME DELIVERED PER DROP A MEASUREMENT OF THE VOLUME OF LIQUID DELIVERED PER DROP. 1D AND 1B MODE REPLY12AG67 CMCND /D/ 03DESIGNATION,CHEMICAL CHEMICAL DESIGNATION THE TERM BY WHICH THE CHEMICAL IS KNOWN OR IDENTIFIED. SELECT REPLY CODE 10AG54 CMCPJ /D/ 10TEMP AT WHICH RATED TEMP AT WHICH RATED THE TEMPERATURE AT WHICH A RATING IS ESTABLISHED. 1D AND 1B MODE REPLY13AJ40 CMCQJ /D/ 10AMOUNT PER AMPUL,CHEMICAL CHEMICAL AMOUNT PER AMPUL A MEASUREMENT OF THE AMOUNT OF CHEMICAL PER AMPUL. 1D AND 1B MODE REPLY12AG67 CMCRD /D/ 19STANDARD,RANGE,SERUM SERUM RANGE STANDARD AN INDICATION OF THE RANGE OF SERUM COVERED BY THE STANDARD. SELECT REPLY CODE 10AG52 CMCSJ /D/ 10VOLUME,WATER,DISTILLED DISTILLED WATER VOLUME A MEASUREMENT OF THE VOLUME OF DISTILLED WATER REQUIRED TO RECONSTITUTE THE ITEM. 1D AND 1B MODE REPLY12AG67 CMCTA /D/ 12QUANTITY,STANDARDIZED,SERUM CONSTITUENTS SERUM CONSTITUENTS STANDARDIZED QUANTITY THE NUMBER OF SERUM CONSTITUENTS STANDARDIZED. 1A MODE REPLY 0 CMCWD /D/ 19CONCENTRATION,USP USP CONCENTRATION THE CONCENTRATION OF THE ITEM AS RATED BY THE UNITED STATES PHARMACOPEIA. SELECT REPLY CODE 10AK54 CMCXG /D/ 10POTENCY POTENCY THE RATED CHEMICAL OR MEDICINAL STRENGTH OF A SUBSTANCE. FULL TEXT WRITE-IN 0 CMCYH /D/ 19CHEMICAL AND REACTION CHEMICAL AND REACTION AN INDICATION OF THE CHEMICAL AND THE REACTION IT INDUCES. 2D MODE REPLY 23AN375AG54 CMCZD /D/ 03DESIGNATION,SERUM,TYPING TYPING SERUM DESIGNATION A DESIGNATION USED TO IDENTIFY THE TYPING SERUM. SELECT REPLY CODE 10AG54 CMDBD /D/ 03DESIGNATION,SERUM,DIAGNOSTIC DIAGNOSTIC SERUM DESIGNATION THE TERMINOLOGY WHICH IDENTIFIES A SERUM DESIGNED TO DIAGNOSE A PARTICULAR ORGANISM. SELECT REPLY CODE 10AG54 CMDCD /D/ 18TYPE,ANTIGEN ANTIGEN TYPE INDICATES THE ANTIGEN TYPE. SELECT REPLY CODE 10AK55 CMDDG /D/ 19FACTOR,ANTIGEN ANTIGEN FACTOR THE INDIVIDUAL FORM(S) OR COMPONENT(S) OF THE ANTIGEN. FULL TEXT WRITE-IN 0 CMDFF /D/T10RANGE,PERCENTAGE,TEST PAPER TEST PAPER PERCENTAGE RANGE AN INDICATION OF THE PERCENTAGE RANGE OF THE TEST PAPER. 1F MODE REPLY 0 CMDGJ /D/ 04LENGTH,STRIP,TEST TEST STRIP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A TEST STRIP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CMDHD /D/ 07DEVICE,TEAR-OFF,DISPENSER DISPENSER TEAR-OFF DEVICE AN INDICATION OF WHETHER OR NOT A TEAR-OFF DEVICE IS INCLUDED WITH THE DISPENSER. SELECT REPLY CODE 10AA49 CMDJD /D/ 07CHART,COLOR,IMPRINTED,DISPENSER DISPENSER IMPRINTED COLOR CHART AN INDICATION OF WHETHER OR NOT AN IMPRINTED COLOR CHART IS INCLUDED WITH THE DISPENSER. SELECT REPLY CODE 10AA49 CMDKA /D/ 12QUANTITY ACCOMMODATED,ROLL,DISPENSER DISPENSER ROLL QUANTITY ACCOMMODATED THE NUMBER OF ROLLS ACCOMMODATED BY THE DISPENSER. 1A MODE REPLY 0 CMDLD 19VALENCE VALENCE THE DEGREE OF POWER WHICH EXISTS BETWEEN CERTAIN BODIES OR SUBSTANCES. SELECT REPLY CODE 10AH48 CMDMG 19STRAIN,VIRUS VIRUS STRAIN AN INDICATION OF THE VIRUS STRAIN. FULL TEXT WRITE-IN 0 CMDND /D/ 18TYPE,IMPRESSION IMPRESSION TYPE INDICATES THE TYPE OF IMPRESSION PROVIDED. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/17/2024. SELECT REPLY CODE 10AK54 CMDPG /D/ 03DESIGNATOR AND QUANTITY,SIZE,COMMERCIAL COMMERCIAL SIZE DESIGNATOR AND QUANTITY A DESIGNATION OF THE SIZE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED AND THE NUMBER FURNISHED. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. FULL TEXT WRITE-IN 0 CMDRD /D/ 07FEATURE,USAGE,ORTHODONTIC WORK ORTHODONTIC WORK USAGE FEATURE AN INDICATION OF WHETHER OR NOT AN ORTHODONTIC WORK USAGE FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CMDSD /D/ 07FEATURE,DESIGN,HYDROCOLLOIDS HYDROCOLLOIDS DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A HYDROCOLLOIDS DESIGN FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CMDTD /D/ 07FEATURE,LOCKING,RIM RIM LOCKING FEATURE AN INDICATION OF WHETHER OR NOT A RIM LOCKING FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CMDWD /D/ 07FEATURE,WATER-COOLED WATER-COOLED FEATURE AN INDICATION OF WHETHER OR NOT A WATER-COOLED FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CMDXD /D/ 07BRACKET,WALL WALL BRACKET AN INDICATION OF WHETHER OR NOT A WALL BRACKET IS PROVIDED. SELECT REPLY CODE 10AB22 CMDYD /D/ 18TYPE,TEETH,ANTERIOR ANTERIOR TEETH TYPE INDICATES THE TYPE OF THE ANTERIOR TEETH. SELECT REPLY CODE 10AK54 CMDZA 12QUANTITY,SET,ANTERIOR TEETH ANTERIOR TEETH SET QUANTITY THE NUMBER OF ANTERIOR TEETH SETS PROVIDED. 1A MODE REPLY 0 CMFBA 12QUANTITY PER SET,TEETH,ANTERIOR ANTERIOR TEETH QUANTITY PER SET THE NUMBER OF ANTERIOR TEETH PER SET. 1A MODE REPLY 0 CMFCD /D/ 18TYPE,TEETH,POSTERIOR POSTERIOR TEETH TYPE INDICATES THE TYPE OF THE POSTERIOR TEETH. SELECT REPLY CODE 10AK54 CMFDA 12QUANTITY,SET,POSTERIOR TEETH POSTERIOR TEETH SET QUANTITY THE NUMBER OF POSTERIOR TEETH SETS PROVIDED. 1A MODE REPLY 0 CMFFA 12QUANTITY PER SET,TEETH,POSTERIOR POSTERIOR TEETH QUANTITY PER SET THE NUMBER OF POSTERIOR TEETH PER SET. 1A MODE REPLY 0 CMFGD /D/ 07CURVATURE,CUTOUT FOR ADAPTING TO TOOTH CUTOUT FOR ADAPTING TO TOOTH CURVATURE AN INDICATION OF WHETHER OR NOT A CUTOUT FOR ADAPTING TO THE TOOTH CURVATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CMFHA 12QUANTITY,MATRIX,CROWN CROWN MATRIX QUANTITY THE NUMBER OF CROWN MATRIXES PROVIDED. 1A MODE REPLY 0 CMFJA 12QUANTITY,MATRIX,CERVICAL CERVICAL MATRIX QUANTITY THE NUMBER OF CERVICAL MATRIXES PROVIDED. 1A MODE REPLY 0 CMFKD /D/ 09MATERIAL,MAT MAT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE MAT/S/ IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMFLA 12QUANTITY,WIRE,ARCH ARCH WIRE QUANTITY THE NUMBER OF ARCH WIRES PROVIDED. 1A MODE REPLY 0 CMFMD /D/ 09MATERIAL,WIRE,ARCH ARCH WIRE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ARCH WIRE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMFND /D/ 17SURFACE TREATMENT,WIRE,ARCH ARCH WIRE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL, OR MILD MECHANICAL PROCESS WHICH PROTECTS AN ARCH WIRE SURFACE. SELECT REPLY CODE 10AD09 CMFPJ 04LENGTH,WIRE,ARCH ARCH WIRE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ARCH WIRE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CMFQD 18TYPE,WIRE,ARCH ARCH WIRE TYPE INDICATES THE TYPE OF ARCH WIRE PROVIDED. SELECT REPLY CODE 10AK54 CMFRA 12QUANTITY PER INCH QUANTITY PER INCH AN INDICATION OF THE NUMBER OF ITEMS PER INCH. 1A MODE REPLY 0 CMFSA 12QUANTITY,WIRE,LIGATURE LIGATURE WIRE QUANTITY THE NUMBER OF LIGATURE WIRES PROVIDED. 1A MODE REPLY 0 CMFTD /D/ 09MATERIAL,WIRE,LIGATURE LIGATURE WIRE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE LIGATURE WIRE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMFWD /D/ 17SURFACE TREATMENT,WIRE,LIGATURE LIGATURE WIRE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A LIGATURE WIRE SURFACE. SELECT REPLY CODE 10AD09 CMFXJ 04LENGTH,WIRE,LIGATURE LIGATURE WIRE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A LIGATURE WIRE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CMFYA 12QUANTITY,FLOSS,DENTAL DENTAL FLOSS QUANTITY THE NUMBER OF DENTAL FLOSS PROVIDED. 1A MODE REPLY 0 CMFZJ 04LENGTH,FLOSS,DENTAL DENTAL FLOSS LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A DENTAL FLOSS,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CMGBA 12QUANTITY,BAND,RUBBER RUBBER BAND QUANTITY THE NUMBER OF RUBBER BANDS PROVIDED. 1A MODE REPLY 0 CMGCJ 04DIAMETER,OUTSIDE,RUBBER BAND RUBBER BAND OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE RUBBER BAND,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CMGDD 01COLOR,TUBE TUBE COLOR THE HUE OR TINT OF THE TUBE. SELECT REPLY CODE 10AD06 CMGFD /D/ 09MATERIAL,CAP,BOTTLE BOTTLE CAP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BOTTLE CAP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMGGD 19PROTECTION,ENVIRONMENTAL,BOTTLE CAP BOTTLE CAP ENVIRONMENTAL PROTECTION THE ENVIRONMENTAL ELEMENTS WHICH A BOTTLE CAP IS DESIGNED TO WITHSTAND SATISFACTORILY. SELECT REPLY CODE 10AA65 CMGHD /D/ 09MATERIAL,BOTTLE BOTTLE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BOTTLE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMGJD 14SHAPE,BOTTLE BOTTLE SHAPE THE PHYSICAL CONFIGURATION OF THE BOTTLE. SELECT REPLY CODE 10AD07 CMGKA 12QUANTITY,WEDGE WEDGE QUANTITY THE NUMBER OF WEDGES PROVIDED. 1A MODE REPLY 0 CMGLA /D/ 12QUANTITY,DISK,SEPARATING SEPARATING DISK QUANTITY THE NUMBER OF SEPARATING DISKS PROVIDED. 1A MODE REPLY 0 CMGMD /D/ 09MATERIAL,DISK,SEPARATING SEPARATING DISK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SEPARATING DISK(S) IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMGNJ 04LENGTH,SCREEN SCREEN LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SCREEN,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CMGPJ 04WIDTH,SCREEN SCREEN WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SCREEN,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CMGQG 04SIZE,CASSETTE CASSETTE SIZE DESIGNATES THE SIZE OF THE CASSETTE. FULL TEXT WRITE-IN 0 CMGRA /D/ 10SPEED RATING,MAXIMUM,LENS LENS MAXIMUM SPEED RATING THE MAXIMUM RATED SPEED OF THE LENS. 1A MODE REPLY 0 CMGSG /D/ 10VALUE,PROTECTIVE,HOUSING X-RAY HOUSING X-RAY PROTECTIVE VALUE AN INDICATION OF THE X-RAY PROTECTIVE VALUE OF THE HOUSING,EXCLUDING PORT. FULL TEXT WRITE-IN 0 CMGTD 18TYPE,MOUNTING,HOUSING HOUSING MOUNTING TYPE INDICATES THE TYPE OF HOUSING MOUNT PROVIDED. SELECT REPLY CODE 10AM39 CMGWA /D/ 12QUANTITY,ASSEMBLY,CABLE CABLE ASSEMBLY QUANTITY THE NUMBER OF CABLE ASSEMBLIES PROVIDED. 1A MODE REPLY 0 CMGXJ 10BANDPASS,FREQUENCY,INTERMEDIATE INTERMEDIATE FREQUENCY BANDPASS THE NUMBER OF HERTZ /CYCLES PER SECOND/ EXPRESSING THE DIFFERENCE BETWEEN THE LIMITING FREQUENCIES AT WHICH THE DESIRED FRACTIONS /USUALLY HALF POWER/ OF THE MAXIMUM OUTPUT IS OBTAINED. 1D AND 1B MODE REPLY11AC32 CMGYD /D/ 07SET,CONE CONE SET AN INDICATION OF WHETHER OR NOT A CONE SET IS PROVIDED. SELECT REPLY CODE 10AB22 CMGZA /D/ 12QUANTITY,SET,CONE CONE SET QUANTITY THE NUMBER OF CONE SETS PROVIDED. 1A MODE REPLY 0 CMHBJ /D/ 04HEIGHT,CONE CONE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE CONE,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 CMHCJ /D/ 04LENGTH,CONE CONE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CMHDJ /D/ 04LENGTH,MAXIMUM,CONE EXTENDED CONE EXTENDED MAXIMUM LENGTH THE MAXIMUM MEASUREMENT OF THE LENGTH THAT THE CONE CAN BE EXTENDED. 1D AND 1B MODE REPLY11AA05 CMHFJ /D/ 04DIAMETER,INSIDE,CONE DISTAL END CONE DISTAL END INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR CONE AT THE DISTAL END,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CMHGG 10PROTECTION RATING,X-RAY X-RAY PROTECTION RATING THE AMOUNT OF X-RAY PROTECTION FOR WHICH THE ITEM IS RATED. FULL TEXT WRITE-IN 0 CMHHA 12QUANTITY,UNIT,HEATING HEATING UNIT QUANTITY THE NUMBER OF HEATING UNITS PROVIDED. 1A MODE REPLY 0 CMHJD 18TYPE,UNIT,HEATING HEATING UNIT TYPE INDICATES THE TYPE OF HEATING UNIT PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AN01 CMHKJ 10TEMP RATING,AMBIENT,MAXIMUM MAXIMUM AMBIENT TEMP RATING THE MAXIMUM TEMPERATURE OF THE MEDIUM SURROUNDING THE ITEM AT WHICH IT CAN BE OPERATED CONTINUOUSLY. 1D AND 1B MODE REPLY11AB36 CMHLD /D/ 07SHUT-OFF,AUTOMATIC,CONDENSER COOLING WATER CONDENSER COOLING WATER AUTOMATIC SHUT-OFF AN INDICATION OF WHETHER OR NOT AN AUTOMATIC SHUT-OFF FOR CONDENSER COOLING WATER IS PROVIDED. SELECT REPLY CODE 10AB22 CMHMD /D/ 07SHUT-OFF,OVERLOAD,THERMAL,MOTOR MOTOR THERMAL OVERLOAD SHUT-OFF AN INDICATION OF WHETHER OR NOT THE MOTOR IS PROVIDED WITH A THERMAL OVERLOAD SHUT-OFF. SELECT REPLY CODE 10AB22 CMHNA /D/ 12QUANTITY,CASSETTE CASSETTE QUANTITY THE NUMBER OF CASSETTES PROVIDED. 1A MODE REPLY 0 CMHPJ /D/ 04LENGTH ACCOMMODATED,MAXIMUM,PAPER PAPER MAXIMUM LENGTH ACCOMMODATED THE MAXIMUM MEASUREMENT OF THE PAPER LENGTH THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 CMHQJ 04WIDTH ACCOMMODATED,MAXIMUM,PAPER PAPER MAXIMUM WIDTH ACCOMMODATED THE MAXIMUM MEASUREMENT OF THE PAPER WIDTH THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 CMHRG 04SIZE FOR WHICH DESIGNED,CASSETTE CASSETTE SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE CASSETTE FOR WHICH THE ITEM IS DESIGNED. FULL TEXT WRITE-IN 0 CMHSA 10RATIO,GRID GRID RATIO THE MAXIMUM TO MINIMUM GRID RATIO,WITH THE LARGER RELATIVE PROPORTION GIVEN,THE LOWER VALUE HAVING AN IMPLIED(NOT GIVEN)VALUE OF ONE (UNITY). 1A MODE REPLY 0 CMHTJ 04THICKNESS,MAXIMUM,LEAD STRIP LEAD STRIP MAXIMUM THICKNESS A MEASUREMENT OF THE MAXIMUM THICKNESS OF THE LEAD STRIP. 1D AND 1B MODE REPLY11AA05 CMHWJ 04WIDTH,MINIMUM,LEAD STRIP LEAD STRIP MINIMUM WIDTH A MEASUREMENT OF THE MINIMUM WIDTH OF THE LEAD STRIP. 1D AND 1B MODE REPLY11AA05 CMHXA 12QUANTITY PER INCH,STRIP,LEAD LEAD STRIP QUANTITY PER INCH THE NUMBER OF LEAD STRIPS PER INCH. 1A MODE REPLY 0 CMHYD /D/ 07FRAME,SUPPORTING,ADJUSTABLE ADJUSTABLE SUPPORTING FRAME AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE SUPPORTING FRAME IS INCLUDED. SELECT REPLY CODE 10AA49 CMHZD /D/ 07TRAY,CASSETTE CASSETTE TRAY AN INDICATION OF WHETHER OR NOT A CASSETTE TRAY IS INCLUDED. SELECT REPLY CODE 10AA49 CMJBG /D/ 04SIZE,FIELD,RADIATION RADIATION FIELD SIZE DESIGNATES THE RADIATION FIELD SIZE. FULL TEXT WRITE-IN 0 CMJCD /D/ 07DEVICE,INDEXING,RADIATION FIELD SIZE RADIATION FIELD SIZE INDEXING DEVICE AN INDICATION OF WHETHER OR NOT AN INDEXING DEVICE TO INDICATE THE FIELD SIZE IS PROVIDED. SELECT REPLY CODE 10AB22 CMJDJ /D/ 04DISTANCE,TARGET TARGET DISTANCE A MEASUREMENT OF THE TARGET DISTANCE. 1D AND 1B MODE REPLY11AA05 CMJFD 05DIRECTION,SHIFT,MECHANICAL MECHANICAL SHIFT DIRECTION THE DIRECTION IN WHICH THE MECHANICAL SHIFT MOVES. SELECT REPLY CODE 10AA38 CMJGJ T10RANGE ABOVE FLOOR,ADJUSTMENT,CHIN REST CHIN REST ADJUSTMENT RANGE ABOVE FLOOR THE MINIMUM AND MAXIMUM LIMITS OF ADJUSTMENT THAT THE CHIN REST CAN BE POSITIONED ABOVE THE FLOOR. 1D AND 1F MODE REPLY11AA05 CMJHJ 04LENGTH ACCOMMODATED,CASSETTE CASSETTE LENGTH ACCOMMODATED A MEASUREMENT OF THE LONGEST DIMENSION OF THE CASSETTE THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CMJJJ 04WIDTH ACCOMMODATED,CASSETTE CASSETTE WIDTH ACCOMMODATED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CASSETTE THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CMJKD /D/ 07STEREO-SHIFTER,VERTICAL VERTICAL STEREO-SHIFTER AN INDICATION OF WHETHER OR NOT A VERTICAL STEREO-SHIFTER IS INCLUDED. SELECT REPLY CODE 10AA49 CMJLD /D/ 07BRACKET,ADAPTER,CONTROL CONTROL ADAPTER BRACKET AN INDICATION OF WHETHER OR NOT A CONTROL ADAPTER BRACKET IS INCLUDED. SELECT REPLY CODE 10AA49 CMJMD /D/ 01COLOR,RESPONSE,SCREEN SPECTRAL FLUOROGRAPHIC TUNNEL SCREEN SPECTRAL FLUOROGRAPHIC TUNNEL RESPONSE COLOR THE PEAK RESPONSE IN COLOR OF THE FLUOROGRAPHIC TUNNEL SPECTRAL REGION. SELECT REPLY CODE 10AD06 CMJNJ /D/ 04DIAMETER,DISK,SEPARATING SEPARATING DISK DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SEPARATING DISK/S/,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CMJPD /D/ 07GRIP,FINGER,SEPARATING DISK SEPARATING DISK FINGER GRIP AN INDICATION OF WHETHER OR NOT A FINGER GRIP IS PROVIDED ON THE SEPARATING DISK/S/. SELECT REPLY CODE 10AB22 CMJQD /D/ 09MATERIAL,SETTER,WEDGE WEDGE SETTER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE WEDGE SETTER IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMJRJ 04LENGTH,SETTER,WEDGE WEDGE SETTER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE WEDGE SETTER,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CMJSJ /D/ 04DIAMETER,SETTER,WEDGE WEDGE SETTER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A WEDGE SETTER,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CMJTD /D/ 17SURFACE TREATMENT EXCLUDING TIPS,PARTS,METAL METAL PARTS SURFACE TREATMENT EXCLUDING TIPS CONSISTS OF PLATING,DIP,AND/OR COATING APPLIED TO THE SURFACE OF THE METAL PARTS,EXCLUDING TIPS,THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A SURFACE. SELECT REPLY CODE 10AD09 CMJWA 12QUANTITY PER SET,ATOMIZER ATOMIZER QUANTITY PER SET THE NUMBER OF ATOMIZERS PROVIDED PER SET. 1A MODE REPLY 0 CMJXD /D/ 07SHOULDER FOR RACK,BOTTLE BOTTLE SHOULDER FOR RACK AN INDICATION OF WHETHER OR NOT A SHOULDER FOR RACK IS INCLUDED ON THE BOTTLE. SELECT REPLY CODE 10AA49 CMJYD /D/ 07COLLAR,METAL,BOTTLE BOTTLE METAL COLLAR AN INDICATION OF WHETHER OR NOT A METAL COLLAR IS INCLUDED ON THE BOTTLE. SELECT REPLY CODE 10AA49 CMJZG /D/ 18TYPE AND QUANTITY,UNIT,SPRAYING SPRAYING UNIT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF SPRAYING UNITS FURNISHED WITH THE ITEM. FULL TEXT WRITE-IN 0 CMKBD /D/ 09MATERIAL,RACK RACK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE RACK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMKCA 12QUANTITY,OPENING,LIGHT LIGHT OPENING QUANTITY THE NUMBER OF LIGHT OPENINGS PROVIDED. 1A MODE REPLY 0 CMKDD 14SHAPE,OPENING,LIGHT LIGHT OPENING SHAPE THE PHYSICAL CONFIGUATION OF THE LIGHT OPENING. SELECT REPLY CODE 10AD07 CMKFD 01COLOR,OPENING,LIGHT LIGHT OPENING COLOR THE HUE OR TINT OF THE LIGHT OPENING. SELECT REPLY CODE 10AD06 CMKGD 01COLOR,PAGE PAGE COLOR THE HUE OR TINT OF A PAGE. SELECT REPLY CODE 10AD06 CMKHD /D/ 09MATERIAL,PAGE PAGE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PAGE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMKJJ 04LENGTH,OVERALL,PAGE PAGE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE PAGE. 2D AND 1B MODE REPLY21AA051AC20 CMKKJ 04WIDTH,OVERALL,PAGE PAGE OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A PAGE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CMKLD 01COLOR,BACKGROUND,PLATE PLATE BACKGROUND COLOR THE HUE OR TINT OF THE PLATE BACKGROUND. SELECT REPLY CODE 10AD06 CMKMD 01COLOR VISION TEST,PLATE PLATE COLOR VISION TEST THE HUE OR TINT OF THE COLOR VISION TEST FOR WHICH THE PLATE IS DESIGNED. SELECT REPLY CODE 10AD06 CMKNA 12QUANTITY,PLATE,DEMONSTRATION DEMONSTRATION PLATE QUANTITY THE NUMBER OF DEMONSTRATION PLATES PROVIDED. 1A MODE REPLY 0 CMKPD 19ARRANGEMENT,FIGURE,OBVERSE SIDE OBVERSE SIDE FIGURE ARRANGEMENT THE ARRANGEMENT OF THE FIGURE(S) ON THE OBVERSE SIDE OF THE ITEM. SELECT REPLY CODE 10AH86 CMKQD 19ARRANGEMENT,FIGURE,REVERSE SIDE REVERSE SIDE FIGURE ARRANGEMENT THE ARRANGEMENT OF THE FIGURE(S) ON THE REVERSE SIDE OF THE ITEM. SELECT REPLY CODE 10AH86 CMKRD 08LOCATION,EYELET EYELET LOCATION INDICATES THE LOCATION OF THE EYELET(S) ON THE ITEM. SELECT REPLY CODE 10AJ91 CMKSD /D/ 07FEATURE,DIMPLE DIMPLE FEATURE AN INDICATION OF WHETHER OR NOT A DIMPLE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CMKTD 01COLOR,FIELD COLOR FIELD THE HUE OR TINT OF THE COLOR FIELD. SELECT REPLY CODE 10AD06 CMKWJ /D/A18TYPE AND QUANTITY,PACKAGE,THIOPENTAL SODIUM THIOPENTAL SODIUM PACKAGE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF CONTAINERS IN WHICH THE THIOPENTAL SODIUM IS PACKAGED. 1D AND 1A MODE REPLY14AE96 CMKXB 10CAPACITY IN CUBIC CENTIMETERS,INJECTION,SODIUM CHLORIDE SODIUM CHLORIDE INJECTION CAPACITY IN CUBIC CENTIMETERS THE VOLUME OF SODIUM CHLORIDE INJECTION,EXPRESSED IN CUBIC CENTIMETERS. 1B MODE REPLY 0 CMKYD /D/ 13THREAD SERIES DESIGNATOR,END,NUT NUT END THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GRUOP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIED DIAMETER OF A NUT END. SELECT REPLY CODE 10AH06 CMKZJ /D/ 13THREAD DIAMETER,END,NUT NUT END THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A NUT END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CMLBA /D/ 13THREAD QUANTITY PER INCH,END,NUT NUT END THREAD QUANTITY PER INCH THE NUMBER OF THREADS ON THE NUT END PER LINEAR INCH,MEASURED ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CMLCD /D/ 13THREAD CLASS,END,NUT NUT END THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE OF THE NUT END AND AN EXTERNAL OR INTERNAL THREAD. SELECT REPLY CODE 10AN53 CMLDD 13THREAD SERIES DESIGNATOR,END,STUD STUD END THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIED DIAMETER OF A STUD END. SELECT REPLY CODE 10AH06 CMLFJ /D/ 13THREAD DIAMETER,END,STUD STUD END THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A STUD END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CMLGA /D/ 13THREAD QUANTITY PER INCH,END,STUD STUD END THREAD QUANTITY PER INCH THE NUMBER OF THREADS ON THE STUD END PER LINEAR INCH,MEASURED ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CMLHD /D/ 13THREAD CLASS,END,STUD STUD END THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE OF THE STUD END AND AN EXTERNAL OR INTERNAL THREAD. SELECT REPLY CODE 10AN53 CMLJJ /D/ 04THREAD LENGTH,END,STUD STUD END THREAD LENGTH A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,OF A STUD END MEASURED ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS. 2D AND 1B MODE REPLY21AA051AC20 CMLKD 13THREAD SERIES DESIGNATOR,HOLE,MOUNTING MOUNTING HOLE THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR THE SPECIFIC DIAMETER OF A THREADED MOUNTING HOLE. SELECT REPLY CODE 10AH06 CMLLJ 04THREAD DIAMETER,HOLE,MOUNTING MOUNTING HOLE THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A THREADED MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CMLMA 13THREAD QUANTITY PER INCH,HOLE,MOUNTING MOUNTING HOLE THREAD QUANTITY PER INCH THE NUMBER OF MOUNTING HOLE THREADS PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CMLND 13THREAD CLASS,HOLE,MOUNTING MOUNTING HOLE THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL MOUNTING HOLE THREAD. SELECT REPLY CODE 10AN53 CMLPA 13THREAD QUANTITY PER INCH THREAD QUANTITY PER INCH THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CMLQD 18TYPE,SCALE,CONTAINER CONTAINER SCALE TYPE INDICATES THE TYPE OF SCALE PROVIDED ON THE CONTAINER. SELECT REPLY CODE 10AM12 CMLRD /D/ 09MATERIAL,CAP,DISPENSING DISPENSING CAP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE DISPENSING CAP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMLSD 18TYPE,CAP,DISPENSING DISPENSING CAP TYPE INDICATES THE TYPE OF DISPENSING CAP. SELECT REPLY CODE 10AK54 CMLTA /D/ 12QUANTITY,TEST TEST QUANTITY THE NUMBER OF TESTS PROVIDED. 1A MODE REPLY 0 CMLWA /D/ 12QUANTITY,TUBE,TEST TEST TUBE QUANTITY THE NUMBER OF TEST TUBES PROVIDED. 1A MODE REPLY 0 CMLXD /D/ 09MATERIAL,RACK,TEST TUBE TEST TUBE RACK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TEST TUBE RACK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMLYD /D/ 07FRAME,VIEWING VIEWING FRAME AN INDICATION OF WHETHER OR NOT A VIEWING FRAME/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CMLZD /D/ 19NAME,SOLUTION,REAGENT REAGENT SOLUTION NAME AN INDICATION OF THE REAGENT SOLUTION NAME. SELECT REPLY CODE 10AJ08 CMMBD /D/ 07CAPSULE,POWDER,REAGENT REAGENT POWDER CAPSULE AN INDICATION OF WHETHER OR NOT A REAGENT POWDER CAPSULE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CMMCJ /D/ 04DIAMETER AND LOCATION,OUTSIDE,CROSS SECTION CROSS SECTION OUTSIDE DIAMETER AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CMMDJ /D/ 04DIAMETER AND LOCATION,INSIDE,CROSS SECTION CROSS SECTION INSIDE DIAMETER AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CMMFJ /D/ 04HEIGHT AND LOCATION,CROSS-SECTIONAL CROSS-SECTIONAL HEIGHT AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CMMGJ /D/ 04WIDTH AND LOCATION,CROSS-SECTIONAL CROSS-SECTIONAL WIDTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CMMHJ /D/ 04THICKNESS AND LOCATION,CROSS-SECTIONAL CROSS-SECTIONAL THICKNESS AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CMMJD 18TYPE,POWER,OPERATING OPERATING POWER TYPE INDICATES THE TYPE OF POWER USED TO OPERATE THE ITEM. SELECT REPLY CODE 10AH83 CMMKB /D/ 10CAPACITY IN MILLIGRAMS CAPACITY IN MILLIGRAMS THE AMOUNT THE ITEM WILL HOLD,EXPRESSED IN MILLIGRAMS. 1B MODE REPLY 0 CMMLA /D/ 12QUANTITY,SLIDE,PLASMA COLLECTION PLASMA COLLECTION SLIDE QUANTITY THE NUMBER OF PLASMA COLLECTION SLIDES PROVIDED. 1A MODE REPLY 0 CMMMD /D/ 09MATERIAL,SLIDE,PLASMA COLLECTION PLASMA COLLECTION SLIDE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PLASMA COLLECTION SLIDE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMMNA /D/ 12QUANTITY,LANCET,BLOOD BLOOD LANCET QUANTITY THE NUMBER OF BLOOD LANCETS PROVIDED. 1A MODE REPLY 0 CMMPD /D/ 09MATERIAL,LANCET,BLOOD BLOOD LANCET MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BLOOD LANCET IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMMQA /D/ 12QUANTITY,CARD,DIAGNOSTIC DIAGNOSTIC CARD QUANTITY THE NUMBER OF DIAGNOSTIC CARDS PROVIDED. 1A MODE REPLY 0 CMMRA /D/ 12QUANTITY PER CARD,SPOT,TEST TEST SPOT QUANTITY PER CARD THE NUMBER OF TEST SPOTS PER CARD. 1A MODE REPLY 0 CMMSA /D/ 12QUANTITY IN AMPULS,ANTIGEN ANTIGEN QUANTITY IN AMPULS THE NUMBER OF AMPULS OF ANTIGEN PROVIDED. 1A MODE REPLY 0 CMMTA /D/ 12QUANTITY,TUBE,CAPILLARY CAPILLARY TUBE QUANTITY THE NUMBER OF CAPILLARY TUBES PROVIDED. 1A MODE REPLY 0 CMMWA /D/ 12QUANTITY,NIPPLE,RUBBER RUBBER NIPPLE QUANTITY THE NUMBER OF RUBBER NIPPLES PROVIDED. 1A MODE REPLY 0 CMMXD /D/ 07NEEDLE NEEDLE AN INDICATION OF WHETHER OR NOT A NEEDLE IS PROVIDED. SELECT REPLY CODE 10AB22 CMMYD /D/ 07BOTTLE,DRAINAGE DRAINAGE BOTTLE AN INDICATION OF WHETHER OR NOT A DRAINAGE BOTTLE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CMMZD /D/ 07VALVE,NEEDLE,TANK TANK NEEDLE VALVE AN INDICATION OF WHETHER OR NOT A NEEDLE VALVE IS PROVIDED ON THE TANK. SELECT REPLY CODE 10AB22 CMNBD /D/ 07GAGE,VACUUM VACUUM GAGE AN INDICATION OF WHETHER OR NOT A VACUUM GAGE IS PROVIDED. SELECT REPLY CODE 10AB22 CMNCD /D/ 07SOLUTION,ANTICOAGULANT ANTICOAGULANT SOLUTION AN INDICATION OF WHETHER OR NOT AN ANTICOAGULANT SOLUTION IS PROVIDED. SELECT REPLY CODE 10AB22 CMNDJ 10CAPACITY,SOLUTION,ANTICOAGULANT ANTICOAGULANT SOLUTION CAPACITY THE AMOUNT OF ANTICOAGULANT SOLUTION THE ITEM WILL HOLD. 1D AND 1B MODE REPLY12AG67 CMNFD 18TYPE,SET,DONOR DONOR SET TYPE INDICATES THE TYPE OF DONOR SET PROVIDED. SELECT REPLY CODE 10AK54 CMNGD /D/ 09MATERIAL,STIRRER STIRRER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE STIRRER/S/ IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMNHG 19TITLE,TEST TEST TITLE AN INDICATION OF THE TITLE OF THE TEST. FULL TEXT WRITE-IN 0 CMNJD /D/ 07PUMP,HAND HAND PUMP AN INDICATION OF WHETHER OR NOT A HAND PUMP IS INCLUDED. SELECT REPLY CODE 10AA49 CMNKG 19NAME,SPORE,BACTERIAL TEST BACTERIAL TEST SPORE NAME THE NOMENCLATURE BY WHICH THE BACTERIAL TEST SPORE IS IDENTIFIED. FULL TEXT WRITE-IN 0 CMNLA /D/ 10POPULATION PER STRIP POPULATION PER STRIP AN INDICATION OF THE AMOUNT OF ORGANISMS THAT INHABIT A STRIP. 1A MODE REPLY 0 CMNMD /D/ 18TYPE,TUBE,TRANSILLUMINATOR TRANSILLUMINATOR TUBE TYPE INDICATES THE TYPE OF TRANSILLUMINATOR TUBE PROVIDED. SELECT REPLY CODE 10AA62 CMNNJ 04DISTANCE FROM END TO FLATTED SECTION DISTANCE FROM END TO FLATTED SECTION NONE. 2D AND 1B MODE REPLY21AA051AC20 CMNPJ /D/ 04WIDTH,SLOT,FIRST DRIVE FIRST DRIVE SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CMNQJ /D/ 04WIDTH,SLOT,SECOND DRIVE SECOND DRIVE SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CMNRJ /D/ 04DEPTH,SLOT,DRIVE,FIRST FIRST DRIVE SLOT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CMNSJ /D/ 04DEPTH,SLOT,DRIVE,SECOND SECOND DRIVE SLOT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CMNTJ /D/ 04WIDTH,FOOT,MOUNTING MOUNTING FOOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CMNWJ /D/ 04LENGTH,FOOT,MOUNTING MOUNTING FOOT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CMNXJ /D/ 04THICKNESS,FOOT,MOUNTING MOUNTING FOOT THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CMNYJ /D/ 04LENGTH,PROJECTION,FIRST FIRST PROJECTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CMNZJ 04LENGTH,PROJECTION,SECOND SECOND PROJECTION LENGTH NONE. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 2D AND 1B MODE REPLY21AA051AC20 CMPBJ /D/ 04DIAMETER,PROJECTION,FIRST FIRST PROJECTION DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CMPCJ /D/ 04DIAMETER,PROJECTION,SECOND SECOND PROJECTION DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CMPDJ 04DISTANCE FROM CENTERLINE TO SECOND FLAT DISTANCE FROM CENTERLINE TO SECOND FLAT NONE. 2D AND 1B MODE REPLY21AA051AC20 CMPFA 12QUANTITY PERPENDICULAR TO AXIS,HOLE HOLE QUANTITY PERPENDICULAR TO AXIS NONE. 1A MODE REPLY 0 CMPGG /D/ 04SIZE PERPENDICULAR TO AXIS,HOLE,UNTHREADED UNTHREADED HOLE SIZE PERPENDICULAR TO AXIS NONE. FULL TEXT WRITE-IN 0 CMPHA 12QUANTITY,HOLE,FLANGE FLANGE HOLE QUANTITY NONE. 1A MODE REPLY 0 CMPJA /D/ 12QUANTITY,HOLE,MOUNTING FOOT MOUNTING FOOT HOLE QUANTITY NONE. 1A MODE REPLY 0 CMPKG /D/ 04SIZE,HOLE,FLANGE FLANGE HOLE SIZE NONE. FULL TEXT WRITE-IN 0 CMPLG /D/ 04SIZE,HOLE,MOUNTING FOOT MOUNTING FOOT HOLE SIZE NONE. FULL TEXT WRITE-IN 0 CMPMJ 04DISTANCE BETWEEN FLANGE HOLE CENTERS DISTANCE BETWEEN FLANGE HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 CMPNJ /D/ 04DIAMETER,CIRCLE,BOLT,FLANGE HOLE FLANGE HOLE BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CMPPJ /D/ 04DISTANCE BETWEEN MOUNTING FOOT HOLE CENTERS DISTANCE BETWEEN MOUNTING FOOT HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 CMPQJ /D/ 04DIAMETER,CIRCLE,BOLT,MOUNTING FOOT HOLE MOUNTING FOOT HOLE BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CMPRJ /D/ 13THREAD LENGTH,INTERNAL,FIRST FIRST INTERNAL THREAD LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CMPSJ /D/ 13THREAD LENGTH,INTERNAL,SECOND SECOND INTERNAL THREAD LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CMPTG /D/ 13THREAD CHARACTERISTICS,INTERNAL,FIRST FIRST INTERNAL THREAD CHARACTERISTICS NONE. FULL TEXT WRITE-IN 0 CMPWG /D/ 13THREAD CHARACTERISTICS,INTERNAL,SECOND SECOND INTERNAL THREAD CHARACTERISTICS NONE. FULL TEXT WRITE-IN 0 CMPXG /D/ 13THREAD CHARACTERISTICS,EXTERNAL EXTERNAL THREAD CHARACTERISTICS NONE. FULL TEXT WRITE-IN 0 CMPYD /D/ 07CLOTH,POLISHING POLISHING CLOTH AN INDICATION OF WHETHER OR NOT A POLISHING CLOTH IS INCLUDED. SELECT REPLY CODE 10AA49 CMPZB 10PERCENTAGE,MAXIMUM,INSOLUBLE MATTER INSOLUBLE MATTER MAXIMUM PERCENTAGE THE MAXIMUM PERCENTAGE OF INSOLUBLE MATTER CONTAINED IN THE ITEM. 1B MODE REPLY 0 CMQBD /D/ 07CHARACTERISTIC,BIODEGRADEABLE BIODEGRADEABLE CHARACTERISTIC AN INDICATION OF WHETHER OR NOT A BIODEGRADEABLE CHARACTERISTIC IS INCLUDED. SELECT REPLY CODE 10AA49 CMQCB 10PERCENTAGE,CONTENT,BIODEGRADEABLE,MINIMUM MINIMUM BIODEGRADEABLE CONTENT PERCENTAGE THE MINIMUM PERCENTAGE OF THE BIODEGRADEABLE CONTENT OF THE ITEM. 1B MODE REPLY 0 CMQDD /D/ 07CHARACTERISTIC,FOAMING FOAMING CHARACTERISTIC AN INDICATION OF WHETHER OR NOT A FOAMING CHARACTERISTIC IS INCLUDED. SELECT REPLY CODE 10AA49 CMQFD /D/ 07FEATURE,CASEHARDENING CASEHARDENING FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES A CASEHARDENING FEATURE. SELECT REPLY CODE 10AA49 CMQGB /D/ 10PERCENTAGE,ALKALINITY,TOTAL,SODIUM OXIDE SODIUM OXIDE TOTAL ALKALINITY PERCENTAGE THE PERCENTAGE OF TOTAL ALKALINITY AS SODIUM OXIDE CONTAINED IN THE ITEM. 1B MODE REPLY 0 CMQHB /D/ 10PERCENTAGE,ALKALINITY,FREE,SODIUM HYDROXIDE SODIUM HYDROXIDE FREE ALKALINITY PERCENTAGE THE PERCENTAGE OF FREE ALKALINITY AS SODIUM HYDROXIDE CONTAINED IN THE ITEM. 1B MODE REPLY 0 CMQJD /D/ 07AGENT,ACTIVE,SURFACE SURFACE ACTIVE AGENT AN INDICATION OF WHETHER OR NOT A SURFACE ACTIVE AGENT(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CMQKG /D/ 10RANGE AT SPECIFIED TEMP,PH,HYDROGEN ION HYDROGEN ION PH RANGE AT SPECIFIED TEMP THE MINIMUM TO MAXIMUM LIMITS OF THE HYDROGEN ION PH AT A SPECIFIED TEMPERATURE. FULL TEXT WRITE-IN 0 CMQLD /D/ 07FEATURE,GRADED,ARCTIC ARCTIC GRADED FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES AN ARCTIC GRADED FEATURE. SELECT REPLY CODE 10AA49 CMQMJ /D/ 10CONTENT,WAX,MINIMUM MINIMUM WAX CONTENT THE MINIMUM AMOUNT OF WAX CONTAINED IN THE ITEM. 1D AND 1B MODE REPLY12AB49 CMQNJ 04DISTANCE,FRONT TO BACK FRONT TO BACK DISTANCE THE DISTANCE FROM THE FRONT TO THE BACK OF AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 CMQPA 04SIZE,GAGE,STIPPLE SHEET STIPPLE SHEET GAGE SIZE DESIGNATES THE STIPPLE SHEET GAGE SIZE. 1A MODE REPLY 0 CMQQB /D/ 04ANGLE IN DEG FOR WHICH DESIGNED,TEETH,POSTERIOR POSTERIOR TEETH ANGLE IN DEG FOR WHICH DESIGNED THE POSTERIOR TEETH ANGLE FOR WHICH THE ITEM IS DESIGNED,EXPRESSED IN DEGREES. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 1B MODE REPLY 0 CMQRD /D/ 07BAND,MATRIX MATRIX BAND AN INDICATION OF WHETHER OR NOT A MATRIX BAND(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CMQSD /D/ 07BAR,PRY PRY BAR AN INDICATION OF WHETHER OR NOT A PRY BAR IS INCLUDED. SELECT REPLY CODE 10AA49 CMQTD /D/ 07CLAMP,CHIN CHIN CLAMP AN INDICATION OF WHETHER OR NOT A CHIN CLAMP IS INCLUDED. SELECT REPLY CODE 10AA49 CMQUA 12CREW MEMBER QUANTITY CREW MEMBER QUANTITY THE NUMBER OF CREW MEMBER NECESSARY FOR THE OPERATION OF THE ARTICLE. 1A MODE REPLY 0 CMQWD /D/ 07CLAMP,ADJUSTABLE ADJUSTABLE CLAMP AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE CLAMP IS INCLUDED. SELECT REPLY CODE 10AA49 CMQXD /D/ 07DEVICE,ANTIROTATING,HANDPIECE HANDPIECE ANTIROTATING DEVICE AN INDICATION OF WHETHER OR NOT A HANDPIECE ANTIROTATING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 CMQYD /D/ 07STOP,EXTENSION,ARM ARM EXTENSION STOP AN INDICATION OF WHETHER OR NOT AN ARM EXTENSION STOP IS INCLUDED. SELECT REPLY CODE 10AA49 CMQZA 12QUANTITY ACCOMMODATED,PELLET PELLET QUANTITY ACCOMMODATED AN INDICATION OF THE NUMBER OF PELLETS THE ITEM IS DESIGNED TO ACCOMMODATE. 1A MODE REPLY 0 CMRBD /D/ 07ADAPTER,CAPSULE,PRE-LOADING PRE-LOADING CAPSULE ADAPTER AN INDICATION OF WHETHER OR NOT A PRE-LOADING CAPSULE ADAPTER IS INCLUDED. SELECT REPLY CODE 10AA49 CMRCD /D/ 18TYPE,CLIP,MOUNTING,HANDPIECE HANDPIECE MOUNTING CLIP TYPE INDICATES THE TYPE OF HANDPIECE MOUNTING CLIP/S/ FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AK54 CMRDA 12QUANTITY PER GUIDE,SHADE SHADE QUANTITY PER GUIDE AN INDICATION OF THE NUMBER OF SHADES PER GUIDE. 1A MODE REPLY 0 CMRFD /D/ 07FEATURE,STERILIZABLE,TEETH TEETH STERILIZABLE FEATURE AN INDICATION OF WHETHER OR NOT A TEETH STERILIZABLE FEATURE IS INCLUDED. USE MRC CBBL SELECT REPLY CODE 10AA49 CMRGJ 10CAPACITY,RESERVOIR RESERVOIR CAPACITY THE AMOUNT OF FLUID THE RESERVOIR IS DESIGNED TO HOLD. 1D AND 1B MODE REPLY12AG67 CMRHD /D/ 07STOPPER,THREADED THREADED STOPPER AN INDICATION OF WHETHER OR NOT A THREADED STOPPER(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CMRJD /D/ 07DEVICE,PROPORTIONING PROPORTIONING DEVICE AN INDICATION OF WHETHER OR NOT A PROPORTIONING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 CMRKD /D/ 07ADJUSTABLE BY WEIGHT FEATURE,PROPORTIONS PROPORTIONS ADJUSTABLE BY WEIGHT FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE IS INCLUDED TO ADJUST THE PROPORTIONS BY WEIGHT. SELECT REPLY CODE 10AA49 CMRLJ 10TEMP,BURN OUT,PATTERN PATTERN BURN OUT TEMP THE TEMPERATURE AT WHICH THE PATTERN WILL BURN OUT. 1D AND 1B MODE REPLY12AG67 CMRMD 18TYPE,CLASP CLASP TYPE INDICATES THE TYPE OF CLASP PROVIDED. SELECT REPLY CODE 10AK54 CMRNJ /D/T18TYPE AND RANGE,SCALE SCALE TYPE AND RANGE INDICATES THE TYPE OF SCALE PROVIDED AND THE MINIMUM TO MAXIMUM VALVES RECORDED. 2D AND 1F MODE REPLY22AJ202AG67 CMRPD 11METHOD,ATTACHMENT,CHUCK TO HANDLE CHUCK TO HANDLE ATTACHMENT METHOD THE MEANS BY WHICH THE CHUCK IS ATTACHED TO THE HANDLE. SELECT REPLY CODE 10AF69 CMRQD /D/ 07SLIDE SLIDE AN INDICATION OF WHETHER OR NOT A SLIDE IS INCLUDED. SELECT REPLY CODE 10AA49 CMRRD /D/ 07HOLE,HANDLE HANDLE HOLE AN INDICATION OF WHETHER OR NOT A HOLE IS INCLUDED IN THE HANDLE. SELECT REPLY CODE 10AA49 CMRSD /D/ 07FEATURE,CONTROL,DISPENSER CAP DISPENSER CAP CONTROL FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE IS INCLUDED FOR CONTROLLING THE AMOUNT DISPENSED BY THE DISPENSER CAP. SELECT REPLY CODE 10AA49 CMRTJ 04HEIGHT,OVERALL,RESERVOIR RESERVOIR OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE RESERVOIR. 2D AND 1B MODE REPLY21AA051AC20 CMRWJ 04DIAMETER,OVERALL,RESERVOIR RESERVOIR OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF THE RESERVOIR. 2D AND 1B MODE REPLY21AA051AC20 CMRXJ /D/ 04WIDTH,OVERALL,RESERVOIR RESERVOIR OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT THE RIGHT ANGLES TO THE LENGTH OF A RESERVOIR,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CMRYD /D/ 09MATERIAL,COLLAR COLLAR MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE COLLAR IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMRZD /D/ 09MATERIAL,PESTLE PESTLE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PESTLE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMSBD /D/ 07CORE,METAL METAL CORE AN INDICATION OF WHETHER OR NOT A METAL CORE IS INCLUDED. SELECT REPLY CODE 10AA49 CMSCD /D/ 09MATERIAL,POST POST MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE POST IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMSDD /D/ 09MATERIAL,END,SHANK/WORKING SHANK/WORKING END MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SHANK AND WORKING END ARE FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMSFD /D/ 17SURFACE TREATMENT,COLLAR COLLAR SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE COLLAR SURFACE. SELECT REPLY CODE 10AD09 CMSGD /D/ 17SURFACE TREATMENT,FERRULE FERRULE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPEDOFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A FERRULE SURFACE. SELECT REPLY CODE 10AD09 CMSHD /D/ 17SURFACE TREATMENT,NOZZLE NOZZLE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A NOZZLE SURFACE. SELECT REPLY CODE 10AD09 CMSJD /D/ 17SURFACE TREATMENT,POINT POINT SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE POINT SURFACE. SELECT REPLY CODE 10AD09 CMSKD /D/ 17SURFACE TREATMENT,POST POST SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A POST SURFACE. SELECT REPLY CODE 10AD09 CMSLD /D/ 01COLOR,BOWL BOWL COLOR THE HUE OR TINT OF THE BOWL. SELECT REPLY CODE 10AD06 CMSMD /D/ 01COLOR,BRACKET BRACKET COLOR THE HUE OR TINT OF THE BRACKET. SELECT REPLY CODE 10AD06 CMSNA 10UNITS PER MILLILITER,AGGLUTINATION,TITER CHICK CELL TITER CHICK CELL AGGLUTINATION UNITS PER MILLILITER A MEASUREMENT OF THE TITER OF THE ITEM,EXPRESSED IN THE NUMBER OF CHICK CELL AGGLUTINATION UNITS PER MILLILITER. 1A MODE REPLY 0 CMSPD /D/ 07ADSORBENT ADSORBENT AN INDICATION OF WHETHER OR NOT AN ADSORBENT IS INCLUDED. SELECT REPLY CODE 10AA49 CMSQD 09MATERIAL,ADSORBENT ADSORBENT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ADSORBENT IS FABRICATED. SELECT REPLY CODE 10AG54 CMSRD /D/ 19SOURCE,TISSUE TISSUE SOURCE AN INDICATION OF THE SOURCE OR ORIGIN OF THE TISSUE. SELECT REPLY CODE 10AM85 CMSSD /D/ 07SOLUTION,CHLORIDE,CALCIUM CALCIUM CHLORIDE SOLUTION AN INDICATION OF WHETHER OR NOT CALCIUM CHLORIDE SOLUTION IS INCLUDED. SELECT REPLY CODE 10AA49 CMSTB /D/ 10MOLARITY PER LITER MOLARITY PER LITER AN INDICATION OF THE MOLARITY OF THE ITEM PER LITER. 1B MODE REPLY 0 CMSWD /D/ 18TYPE,CONTAINER,SOLUTION SOLUTION CONTAINER TYPE INDICATES THE TYPE OF CONTAINER PROVIDED FOR THE SOLUTION. SELECT REPLY CODE 10AE96 CMSXD /D/ 09MATERIAL,HEAD,SQUARE/MITER SQUARE/MITER HEAD MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SQUARE AND MITER HEAD ARE FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMSYD /D/ 03DESIGNATION,HARDNESS,SQUARE/MITER HEAD SQUARE/MITER HEAD HARDNESS DESIGNATION AN INDICATION OF THE RELATIVE HARDNESS OF THE SQUARE AND MITER HEAD. SELECT REPLY CODE 10AK55 CMSZD 03DESIGNATION,HARDNESS,BEAM BEAM HARDNESS DESIGNATION AN INDICATION OF THE RELATIVE HARDNESS OF THE BEAM. SELECT REPLY CODE 10AK55 CMTBD 03DESIGNATION,HARDNESS,BLADE BLADE HARDNESS DESIGNATION AN INDICATION OF THE RELATIVE HARDNESS OF THE BLADE. SELECT REPLY CODE 10AK55 CMTCJ A10UNIT,GRADUATION,SMALLEST,BLADE EDGE BLADE EDGE SMALLEST GRADUATION UNIT THE SMALLEST INCREMENT OF MEASURE ON THE BLADE EDGE/S/. 1D AND 1A MODE REPLY13AK09 CMTDD /D/ 07SCRIBER,HEAD,SQUARE/MITER SQUARE/MITER HEAD SCRIBER AN INDICATION OF WHETHER OR NOT A SCRIBER IS INCLUDED WITH THE SQUARE AND MITER HEAD. SELECT REPLY CODE 10AA49 CMTFA /D/ 12QUANTITY,LEVEL,SQUARE/MITER HEAD SQUARE/MITER HEAD LEVEL QUANTITY THE NUMBER OF LEVELS BUILT INTO THE SQUARE AND MITER HEAD. 1A MODE REPLY 0 CMTGD /D/ 07HEAD,CENTER CENTER HEAD AN INDICATION OF WHETHER OR NOT A CENTER HEAD IS INCLUDED. SELECT REPLY CODE 10AA49 CMTHD /D/ 07HEAD,PROTRACTOR PROTRACTOR HEAD AN INDICATION OF WHETHER OR NOT A PROTRACTOR HEAD IS INCLUDED. SELECT REPLY CODE 10AA49 CMTJD /D/ 07LEVEL LEVEL AN INDICATION OF WHETHER OR NOT A LEVEL IS INCLUDED. SELECT REPLY CODE 10AA49 CMTKJ 04LENGTH,BLADE FACE TO BEAM BLADE FACE TO BEAM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BLADE FACE FROM END TO BEAM. 2D AND 1B MODE REPLY21AA051AC20 CMTLD 07DETACHABILITY,BEAM BEAM DETACHABILITY AN INDICATION OF WHETHER OR NOT THE BEAM IS DETACHABLE. SELECT REPLY CODE 10AH97 CMTNG 19TABLE,REFERENCE,INSCRIBED INSCRIBED REFERENCE TABLE THE REFERENCE TABLE/S/ INSCRIBED ON THE ITEM. FULL TEXT WRITE-IN 0 CMTPJ /D/A10UNIT,GRADUATION,BODY BODY GRADUATION UNIT THE INCREMENT OF MEASURE REPRESENTED BY THE MARKING/S/ ON THE BODY. 1D AND 1A MODE REPLY13AK09 CMTQD /D/ 07FEATURE,FILLED,MERCURY MERCURY FILLED FEATURE AN INDICATION OF WHETHER OR NOT A MERCURY FILLED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CMTRD 07REMOVABILITY,TOP TOP REMOVABILITY AN INDICATION OF WHETHER OR NOT THE TOP IS REMOVABLE. SELECT REPLY CODE 10AB00 CMTSD 07ADJUSTABILITY,TOP TOP ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE TOP IS ADJUSTABLE. SELECT REPLY CODE 10AB00 CMTTD 03DESIGNATION,HARDNESS,POINT POINT HARDNESS DESIGNATION AN INDICATION OF THE RELATIVE HARDNESS OF THE POINT. SELECT REPLY CODE 10AK55 CMTWD 07REMOVABILITY,POINT POINT REMOVABILITY AN INDICATION OF WHETHER OR NOT THE POINT IS REMOVABLE. SELECT REPLY CODE 10AB00 CMTXJ A10UNIT,GRADUATION,EDGE SMALLEST EDGE SMALLEST GRADUATION UNIT THE SMALLEST INCREMENT OF MEASURE ON THE EDGE/S/ OF THE ITEM. 1D AND 1A MODE REPLY13AK09 CMTYJ /D/A10UNIT,GRADUATION,END END GRADUATION UNIT THE INCREMENT OF MEASURE REPRESENTED BY THE MARKING/S/ ON THE END/S/ OF THE ITEM. 1D AND 1A MODE REPLY13AK09 CMTZJ /D/A10UNIT,GRADUATION,CENTER CENTER GRADUATION UNIT THE INCREMENT OF MEASURE REPRESENTED BY THE MARKING/S/ ON THE CENTER OF THE ITEM. 1D AND 1A MODE REPLY13AK09 CMWBD /D/ 07EDGE,BEVELED BEVELED EDGE AN INDICATION OF WHETHER OR NOT A BEVELED EDGE IS INCLUDED ON THE ITEM. SELECT REPLY CODE 10AA49 CMWCD 05DIRECTION,READING READING DIRECTION AN INDICATION OF THE DIRECTION IN WHICH THE ITEM IS READ. SELECT REPLY CODE 10AA38 CMWDD 18TYPE,TABLE,CONVERSION CONVERSION TABLE TYPE INDICATES THE TYPE OF CONVERSION TABLE PROVIDED. SELECT REPLY CODE 10AJ40 CMWFD /D/ 07END,TAPERED TAPERED END AN INDICATION OF WHETHER OR NOT A TAPERED END/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CMWGG /D/ 10SCALE,SHRINKAGE SHRINKAGE SCALE THE AMOUNT OF SHRINKAGE FOR WHICH THE GRADUATIONS ARE ADJUSTED FOR A GIVEN MEASUREMENT SCALE. FULL TEXT WRITE-IN 0 CMWHD /D/ 07SCALE,SHRINK,DOUBLE DOUBLE SHRINK SCALE AN INDICATION OF WHETHER OR NOT A DOUBLE SHRINK SCALE IS INCLUDED. SELECT REPLY CODE 10AA49 CMWJD /D/ 07SCALE,STANDARD STANDARD SCALE AN INDICATION OF WHETHER OR NOT A STANDARD SCALE IS INCLUDED. SELECT REPLY CODE 10AA49 CMWKG /D/ 10UNIT,GRADUATION,STANDARD STANDARD GRADUATION UNIT AN INDICATION OF THE STANDARD UNIT/S/ OF GRADUATION ON THE ITEM. FULL TEXT WRITE-IN 0 CMWLG 10CAPACITY,MEASURING MEASURING CAPACITY THE MAXIMUM MEASURING CAPACITY OF THE ITEM. FULL TEXT WRITE-IN 0 CMWMG /D/ 10UNIT,GRADUATION,SMALLEST,TAPE TAPE SMALLEST GRADUATION UNIT AN INDICATION OF THE SMALLEST UNIT/S/ OF GRADUATION OF THE TAPE. FULL TEXT WRITE-IN 0 CMWND /D/ 14SHAPE,TUBE,TRANSILLUMINATOR TRANSILLUMINATOR TUBE SHAPE THE PHYSICAL CONFIGURATION OF THE TRANSILLUMINATOR TUBE(S). SELECT REPLY CODE 10AD07 CMWPD /D/ 18TYPE,HEAD,OTOSCOPE OTOSCOPE HEAD TYPE INDICATES THE TYPE OF OTOSCOPE HEAD PROVIDED. SELECT REPLY CODE 10AE98 CMWQD /D/ 07CORD,BATTERY BATTERY CORD AN INDICATION OF WHETHER OR NOT A BATTERY CORD(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CMWRD /D/ 07CORD,HANDLE/CONNECTING HANDLE/CONNECTING CORD AN INDICATION OF WHETHER OR NOT A HANDLE AND/OR CONNECTING CORD IS INCLUDED. SELECT REPLY CODE 10AA49 CMWSD /D/ 07HOOD,ANTRUM ANTRUM HOOD AN INDICATION OF WHETHER OR NOT AN ANTRUM HOOD(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CMWTA /D/ 12QUANTITY,HOOD,ANTRUM ANTRUM HOOD QUANTITY THE NUMBER OF ANTRUM HOODS PROVIDED. 1A MODE REPLY 0 CMWWD /D/ 07HOOD,SINUS,FRONTAL FRONTAL SINUS HOOD AN INDICATION OF WHETHER OR NOT A FRONTAL SINUS HOOD(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CMWXA /D/ 12QUANTITY,HOOD,FRONTAL SINUS FRONTAL SINUS HOOD QUANTITY THE NUMBER OF FRONTAL SINUS HOODS PROVIDED. 1A MODE REPLY 0 CMWYD 18TYPE,SPECULUM SPECULUM TYPE INDICATES THE TYPE OF SPECULUM PROVIDED. SELECT REPLY CODE 10AK54 CMWZD /D/ 09MATERIAL,SPECULUM SPECULUM MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SPECULUM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CMXBD 04SIZE,SPECULUM SPECULUM SIZE DESIGNATES THE SIZE OF THE SPECULUM. SELECT REPLY CODE 10AF81 CMXCD 03DESIGNATION,DESIGN,OPHTHALMOSCOPE HEAD OPHTHALMOSCOPE HEAD DESIGN DESIGNATION THE DESIGNATION DERIVED FROM THE NAME OF THE DESIGNER OR THE USE FOR WHICH THE OPHTHALMOSCOPE HEAD IS DESIGNED. SELECT REPLY CODE 10AJ50 CMXDA 12QUANTITY,LAMPHOLDER,OPHTHALMOSCOPE HEAD OPHTHALMOSCOPE HEAD LAMPHOLDER QUANTITY THE NUMBER OF LAMPHOLDERS INCLUDED ON THE OPHTHALMOSCOPE HEAD. 1A MODE REPLY 0 CMXFA 12QUANTITY,LAMP,HEAD,OPHTHALMOSCOPE OPHTHALMOSCOPE HEAD LAMP QUANTITY THE NUMBER OF LAMPS INCLUDED WITH THE OPHTHALMOSCOPE HEAD. 1A MODE REPLY 0 CMXGB 10VOLTAGE RATING IN VOLTS,LAMP,HEAD,OPHTHALMOSCOPE OPHTHALMOSCOPE HEAD LAMP VOLTAGE RATING IN VOLTS THE VOLTAGE FOR WHICH THE OPHTHALMOSCOPE HEAD LAMP IS RATED,EXPRESSED IN VOLTS. 1B MODE REPLY 0 CMXHB /D/ 10WATTAGE RATING IN WATTS,LAMP,HEAD,OPHTHALMOSCOPE OPHTHALMOSCOPE HEAD LAMP WATTAGE RATING IN WATTS THE RATED POWER THAT AN OPHTHALMOSCOPE HEAD LAMP CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS. 1B MODE REPLY 0 CMXJJ 10CURRENT RATING,LAMP,HEAD,OPHTHALMOSCOPE OPHTHALMOSCOPE HEAD LAMP CURRENT RATING THE AMOUNT OF CURRENT FOR WHICH THE OPHTHALMOSCOPE HEAD LAMP IS RATED. 1D AND 1B MODE REPLY11AC30 CMXKB 10CANDLEPOWER RATING IN FOOTCANDLES,LAMP,HEAD,OPHTHALMOSCOPE OPHTHALMOSCOPE HEAD LAMP CANDLEPOWER RATING IN FOOTCANDLES THE CANDLEPOWER OR MEASUREMENT OF LUMINOUS INTENSITY FOR WHICH THE OPHTHALMOSCOPE HEAD LAMP IS RATED,EXPRESSED IN FOOTCANDLES. 1B MODE REPLY 0 CMXLB /D/ 10LUMINOSITY IN LUMENS,LAMP,HEAD,OPHTHALMOSCOPE OPHTHALMOSCOPE HEAD LAMP LUMINOSITY IN LUMENS THE MEASUREMENT OF LUMINOUS FLUX FOR WHICH THE OPHTHALMOSCOPE HEAD LAMP IS RATED,EXPRESSED IN LUMENS. 1B MODE REPLY 0 CMXML /D/ 16STYLE,BULB,OPHTHALMOSCOPE HEAD LAMP OPHTHALMOSCOPE HEAD LAMP BULB STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE OPHTHALMOSCOPE HEAD LAMP BULB. 1L MODE REPLY 0 CMXNA 03DESIGNATOR,SIZE,OPHTALMOSCOPE HEAD LAMP BULB OPHTHALMOSCOPE HEAD LAMP BULB SIZE DESIGNATOR THE DESIGNATION THAT DESCRIBES THE SIZE OF AN OPHTHALMOSCOPE HEAD LAMP BULB. 1A MODE REPLY 0 CMXPL 16STYLE,BASE,OPHTHALMOSCOPE HEAD LAMP OPHTHALMOSCOPE HEAD LAMP BASE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE OPHTHALMOSCOPE HEAD LAMP BASE. 1L MODE REPLY 0 CMXQA /D/ 19NUMBER,INDUSTRY,OPHTHALMOSCOPE HEAD LAMP OPHTHALMOSCOPE HEAD LAMP INDUSTRY NUMBER THE MEANS ESTABLISHED TO IDENTIFY THE OPHTHALMOSCOPE HEAD LAMP BY AN INDUSTRY STANDARD NUMBER. 1A MODE REPLY 0 CMXRD 19TRANSPARENCY,LAMP,HEAD,OPHTHALMOSCOPE OPHTHALMOSCOPE HEAD LAMP TRANSPARENCY THE ABILITY OF THE OPHTHALMOSCOPE HEAD LAMP TO TRANSMIT LIGHT AND ALLOW VISUAL PERCEPTION. SELECT REPLY CODE 10AF93 CMXSF T10RANGE IN DIOPTERS,NEGATIVE,OPHTHALMOSCOPE HEAD LENS OPHTHALMOSCOPE HEAD LENS NEGATIVE RANGE IN DIOPTERS THE NEGATIVE RANGE FOR WHICH THE OPHTHALMOSCOPE HEAD LENS IS RATED,EXPRESSED IN DIOPTERS. 1F MODE REPLY 0 CMXTF T10RANGE IN DIOPTERS,POSITIVE,OPHTHALMOSCOPE HEAD LENS OPHTHALMOSCOPE HEAD LENS POSITIVE RANGE IN DIOPTERS THE POSITIVE RANGE FOR WHICH THE OPHTHALMOSCOPE HEAD LENS IS RATED,EXPRESSED IN DIOPTERS. 1F MODE REPLY 0 CMXWD /D/ 07APERTURE,ZERO,OPHTHALMOSCOPE HEAD LENS OPHTHALMOSCOPE HEAD LENS ZERO APERTURE AN INDICATION OF WHETHER OR NOT A ZERO APERTURE IS INCLUDED ON THE OPHTHALMOSCOPE HEAD LENS. SELECT REPLY CODE 10AA49 CMXXD /D/ 07FEATURE,COATED COATED FEATURE AN INDICATION OF WHETHER OR NOT A COATED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CMXYD /D/ 07FEATURE,CAPILLARY CAPILLARY FEATURE AN INDICATION OF WHETHER OR NOT A CAPILLARY FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CMXZA 12QUANTITY,SUTURE SUTURE QUANTITY THE NUMBER OF SUTURES PROVIDED. 1A MODE REPLY 0 CMYBJ 04LENGTH,SUTURE SUTURE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A SUTURE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CMYCG /D/ 19NAME,SPECIFICATION SPECIFICATION NAME THE NOMENCLATURE BY WHICH THE SPECIFICATION IS IDENTIFIED. FULL TEXT WRITE-IN 0 CMYDD /D/ 18TYPE,FLUID,TUBING TUBING FLUID TYPE INDICATES THE TYPE OF TUBING FLUID PROVIDED. SELECT REPLY CODE 10AB75 CMYFD /D/ 08LOCATION,RAIL,DIAGONAL DIAGONAL RAIL LOCATION INDICATES THE LOCATION OF THE DIAGONAL RAIL/S/ ON THE ITEM. SELECT REPLY CODE 10AJ91 CMYGJ 04HEIGHT,OVERALL,SECTION,MEDIAL MEDIAL SECTION OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE MEDIAL SECTION. 1D AND 1B MODE REPLY11AA05 CMYHD /D/ 07PLUG,BOTTOM BOTTOM PLUG AN INDICATION OF WHETHER OR NOT A BOTTOM PLUG IS INCLUDED. SELECT REPLY CODE 10AA49 CMYJJ 04DIAMETER,INSIDE,NECK NECK INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE NECK,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CMYKD /D/ 07FEATURE,POCKET POCKET FEATURE AN INDICATION OF WHETHER OR NOT A POCKET FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CMYLJ 04LENGTH,OPENING OPENING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE OPENING,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CMYMJ 04WIDTH,OPENING,MEDIAL MEDIAL OPENING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MEDIAL OPENING,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CMYND 01COLOR,BRUSH BRUSH COLOR THE HUE OR TINT OF THE BRUSH. SELECT REPLY CODE 10AD06 CMYPD 01COLOR,BRISTLE BRISTLE COLOR THE HUE OR TINT OF THE BRISTLE. SELECT REPLY CODE 10AD06 CMYQD /D/ 01COLOR,PEDESTAL PEDESTAL COLOR THE HUE OR TINT OF THE PEDESTAL. SELECT REPLY CODE 10AD06 CMYRA 12QUANTITY,PLATE,MICA MICA PLATE QUANTITY THE NUMBER OF MICA PLATES PROVIDED. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/16/2024. 1A MODE REPLY 0 CMYSD /D/ 11METHOD,RETENTION,DISC,INDIVIDUAL POST INDIVIDUAL POST DISC RETENTION METHOD THE MEANS USED TO RETAIN THE DISC/S/ ON THE INDIVIDUAL POST. SELECT REPLY CODE 10AE36 CMYTD /D/ 07ASPIRATOR ASPIRATOR AN INDICATION OF WHETHER OR NOT AN ASPIRATOR IS INCLUDED. SELECT REPLY CODE 10AA49 CMYWD /D/ 07FEATURE,MOUNTED,BOWL ADJUSTABLE ARM BOWL ADJUSTABLE ARM MOUNTED FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE IS INCLUDED FOR THE BOWL TO BE MOUNTED ON AN ADJUSTABLE ARM. SELECT REPLY CODE 10AA49 CMYXD /D/ 07SUPPORT,TUMBLER,DRINKING DRINKING TUMBLER SUPPORT AN INDICATION OF WHETHER OR NOT A DRINKING TUMBLER SUPPORT IS INCLUDED. SELECT REPLY CODE 10AA49 CMYZD /D/ 07SHIELD,POWDER POWDER SHIELD AN INDICATION OF WHETHER OR NOT A POWDER SHIELD IS INCLUDED. SELECT REPLY CODE 10AA49 CMZBD 08LOCATION,HOUSING,GEAR GEAR HOUSING LOCATION INDICATES THE LOCATION OF THE GEAR HOUSING/S/. SELECT REPLY CODE 10AJ91 CMZCD 08LOCATION,COVERING COVERING LOCATION INDICATES THE LOCATION OF AN ITEM TO WHICH THE COVERING HAS BEEN APPLIED. SELECT REPLY CODE 10AJ91 CMZDJ 04THICKNESS,TIP,BLADE BLADE TIP THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE BLADE TIP,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CMZFJ 04WIDTH,TIP,BLADE BLADE TIP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BLADE TIP,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CMZGJ 04HEIGHT,OVERALL,BOWL BOWL OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE BOWL. 2D AND 1B MODE REPLY21AA051AC20 CMZHJ 04DIAMETER,OVERALL,BOWL TOP BOWL TOP OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF THE BOWL TOP. 2D AND 1B MODE REPLY21AA051AC20 CMZJJ 04LENGTH,SURFACE,BRUSHING BRUSHING SURFACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BRUSHING SURFACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CMZKJ 04HEIGHT,BRISTLE,EXPOSED EXPOSED BRISTLE HEIGHT A MEASUREMENT FROM THE TOP TO THE BOTTOM OF THE EXPOSED BRISTLE,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CMZLJ /D/ 04DIAMETER,OUTSIDE,CAPSULE CAPSULE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CAPSULE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 2D AND 1B MODE REPLY21AA051AC20 CMZMJ /D/ 04LENGTH,OVERALL,CAPSULE CAPSULE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LOGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CAPSULE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/16/2024. 2D AND 1B MODE REPLY21AA051AC20 CMZNJ /D/ 04DIAMETER,PESTLE PESTLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PESTLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CMZPJ /D/ 04HEIGHT,OVERALL,PEDESTAL PEDESTAL OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE PEDESTAL. 2D AND 1B MODE REPLY21AA051AC20 CMZQJ /D/ 04LENGTH,OVERALL,PESTLE PESTLE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LOGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE PESTLE. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 2D AND 1B MODE REPLY21AA051AC20 CMZRJ /D/ 04DIAMETER,OVERALL,POST POST OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF THE POST. 2D AND 1B MODE REPLY21AA051AC20 CMZSJ /D/ 04HEIGHT,OVERALL,POST POST OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE POST. 2D AND 1B MODE REPLY21AA051AC20 CMZTJ 04LENGTH,BRUSH BRUSH LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A BRUSH,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CMZWJ 04DIAMETER,OUTSIDE,HOLDER HOLDER OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOLDER,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CMZXD /D/ 19INGREDIENT,REDUCING REDUCING INGREDIENT THE AGENT(S) THAT PRODUCES OR IS CAPABLE OF PRODUCING A REDUCING EFFECT. SELECT REPLY CODE 10AJ08 CMZYL 16STYLE,TIP,FIRST FIRST TIP STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FIRST TIP. 1L MODE REPLY 0 CMZZJ 04RADIUS,TIP,SECOND SECOND TIP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNBBJ 04RADIUS,TIP,THIRD THIRD TIP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNBCJ 04RADIUS,TIP,FOURTH FOURTH TIP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNBDJ 04RADIUS,INNER,FIRST TIP FIRST TIP INNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNBFJ 04RADIUS,INNER,SECOND TIP SECOND TIP INNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNBGJ 04RADIUS,INNER,THIRD TIP THIRD TIP INNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNBHJ 04RADIUS,INNER,FOURTH TIP FOURTH TIP INNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNBJJ 04RADIUS,OUTER,FIRST TIP FIRST TIP OUTER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNBKJ 04RADIUS,OUTER,SECOND TIP SECOND TIP OUTER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNBLJ 04RADIUS,OUTER,THIRD TIP THIRD TIP OUTER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNBMJ 04RADIUS,OUTER,FOURTH TIP FOURTH TIP OUTER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNBNJ 04DIMENSION,SMALLER,LOOP/HOLDING LOOP/HOLDING SMALLER DIMENSION NONE. 2D AND 1B MODE REPLY21AA051AC20 CNBPJ 04WIDTH,SMALLER,LOOP OPENING LOOP OPENING SMALLER WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CNBQF /D/T10RANGE IN DEG,ADJUSTMENT ADJUSTMENT RANGE IN DEG THE MINIMUM AND MAXIMUM LIMITS TO WHICH THE ITEM MAY BE ADJUSTED,EXPRESSED IN DEGREES. 1F MODE REPLY 0 CNBRA /D/ 12QUANTITY,DEVICE,POSITIONING POSITIONING DEVICE QUANTITY THE NUMBER OF POSITIONING DEVICES PROVIDED. 1A MODE REPLY 0 CNBSD /D/ 09MATERIAL,CRANK CRANK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CRANK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CNBTD /D/ 18TYPE,MOVEMENT,CRANK CRANK MOVEMENT TYPE INDICATES THE TYPE OF CRANK MOVEMENT PROVIDED. SELECT REPLY CODE 10AL03 CNBWJ 04LENGTH,SCREEN SCREEN LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SCREEN,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CNBXJ 04WIDTH,SCREEN SCREEN WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SCREEN,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CNBYJ /D/ 04DIAMETER,LENS,VIEWING VIEWING LENS DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE VIEWING LENS,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CNBZG /D/ 04SIZE ACCOMMODATED,CASSETTE,MAXIMUM FLUOROGRAPHIC TUNNEL MAXIMUM FLUOROGRAPHIC TUNNEL CASSETTE SIZE ACCOMMODATED THE MAXIMUM FLUOROGRAPHIC TUNNEL CASSETTE SIZE THE ITEM WILL ACCOMMODATE. FULL TEXT WRITE-IN 0 CNCBD /D/ 14SHAPE,GRID,FLUOROGRAPHIC TUNNEL FLUOROGRAPHIC TUNNEL GRID SHAPE THE PHYSICAL CONFIGURATION OF THE FLUOROGRAPHIC TUNNEL GRID. SELECT REPLY CODE 10AD07 CNCCA /D/ 12QUANTITY,COLUMN,STAND STAND COLUMN QUANTITY THE NUMBER OF STAND COLUMNS PROVIDED. 1A MODE REPLY 0 CNCDJ /D/T04HEIGHT RANGE,STAND STAND HEIGHT RANGE THE MINIMUM AND MAXIMUM HEIGHT RANGE OF THE STAND. 1D AND 1F MODE REPLY11AA05 CNCFJ /D/ 13THREAD LENGTH AND LOCATION THREAD LENGTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNCGJ /D/ 04DIAMETER AND LOCATION,HOLE HOLE DIAMETER AND LOCATION THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE AND THE LOCATION. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNCHJ /D/ 04DEPTH AND LOCATION,SLOT SLOT DEPTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNCJJ /D/ 04DIAMETER AND LOCATION,STEP STEP DIAMETER AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNCKJ /D/ 04LENGTH AND LOCATION,STEP STEP LENGTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNCLJ /D/ 04LENGTH AND LOCATION,TAPER TAPER LENGTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNCMJ /D/ 04DIAMETER AND LOCATION,HOLE,FIRST FIRST HOLE DIAMETER AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNCNJ /D/ 04DIAMETER AND LOCATION,HOLE,SECOND SECOND HOLE DIAMETER AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNCPJ /D/ 04WIDTH AND LOCATION,KEYWAY KEYWAY WIDTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNCQJ /D/ 04DEPTH AND LOCATION,KEYWAY KEYWAY DEPTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNCRJ /D/ 04DIAMETER AND LOCATION,SPLINE MINOR SPLINE MINOR DIAMETER AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNCSJ /D/ 04DIAMETER AND LOCATION,SHAFT SHAFT DIAMETER AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNCTJ /D/ 04LENGTH AND LOCATION,FLATTED PORTION FLATTED PORTION LENGTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNCWJ /D/ 04DIAMETER AND LOCATION,UNDERCUT UNDERCUT DIAMETER AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNCXJ /D/ 04LENGTH AND LOCATION,KEYWAY KEYWAY LENGTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNCYJ /D/ 04LENGTH AND LOCATION,UNDERCUT UNDERCUT LENGTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNCZJ /D/ 04DEPTH AND LOCATION,FLAT FLAT DEPTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNDBJ /D/ 04THICKNESS AND LOCATION,TONGUE TONGUE THICKNESS AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNDCJ /D/ 04DISTANCE AND LOCATION,HOLE CENTER TO SHAFT END HOLE CENTER TO SHAFT END DISTANCE AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNDDJ /D/ 04WIDTH ACROSS FLATS AND LOCATION WIDTH ACROSS FLATS AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNDFJ /D/ 04LENGTH AND LOCATION,SPLINE SPLINE LENGTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNDGJ /D/ 04LENGTH AND LOCATION,TONGUE TONGUE LENGTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNDHJ /D/ 04LENGTH AND LOCATION,KEYWAY,SECOND SECOND KEYWAY LENGTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNDJJ /D/ 04WIDTH AND LOCATION,KEYWAY,SECOND SECOND KEYWAY WIDTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNDKJ /D/ 04DISTANCE AND LOCATION,FLAT CENTER TO SHAFT END FLAT CENTER TO SHAFT END DISTANCE AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNDLJ /D/ 04DISTANCE AND LOCATION,KEYWAY CENTER TO SHAFT END KEYWAY CENTER TO SHAFT END DISTANCE AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNDMJ /D/ 04LENGTH AND LOCATION,TOOTH,FULL FULL TOOTH LENGTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNDNJ /D/ 19INGREDIENT AND PERCENTAGE,COLLOID COLLOID INGREDIENT AND PERCENTAGE THE VALUE/S/ OF THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE COLLOID IS FABRICATED. 3D AND 1B MODE REPLY31AC202AG555AG54 CNDPJ /D/ 19INGREDIENT AND PERCENTAGE,SENSITIZER SENSITIZER INGREDIENT AND PERCENTAGE THE VALUE/S/ OF THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SENSITIZER IS FABRICATED. 3D AND 1B MODE REPLY31AC202AG555AG54 CNDQB 10GRAVITY IN DEG BAUME,SPECIFIC SPECIFIC GRAVITY IN DEG BAUME THE SPECIFIC GRAVITY OF AN ITEM,EXPRESSED IN DEGREES BAUME. 1B MODE REPLY 0 CNDRJ 10TEMP RATING,MAXIMUM,FREEZE PROTECTION FREEZE PROTECTION MAXIMUM TEMP RATING THE MAXIMUM TEMPERATURE AT WHICH THE ITEM IS RATED TO PROTECT AGAINST FREEZING. 2D AND 1B MODE REPLY23AJ401AH08 CNDSD /D/ 07FEATURE,NONIRRITATING NONIRRITATING FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES A NONIRRITATING FEATURE. SELECT REPLY CODE 10AA49 CNDTD /D/ 07FEATURE,NONBLINDING NONBLINDING FEATURE AN INDICATION OF WHETHER OR NOT THE ITEM INCLUDES A NONBLINDING FEATURE. SELECT REPLY CODE 10AA49 CNDWB 10PERCENTAGE,CHLORINE,MINIMUM AVAILABLE MINIMUM AVAILABLE CHLORINE PERCENTAGE THE PERCENTAGE OF MINIMUM AVAILABLE CHLORINE CONTAINED IN THE ITEM. 1B MODE REPLY 0 CNDXD /D/ 07AGENT,CONDITIONING,WATER WATER CONDITIONING AGENT AN INDICATION OF WHETHER OR NOT A WATER CONDITIONING AGENT/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CNDYD /D/ 07IMPREGNATION,INDICATOR,MOISTURE MOISTURE INDICATOR IMPREGNATION AN INDICATION OF WHETHER OR NOT MOISTURE INDICATOR IMPREGNATION IS INCLUDED. SELECT REPLY CODE 10AA49 CNDZA 10RATIO,DILUTION DILUTION RATIO THE RATIO OF THE DILUENT TO THE CONCENTRATE. 1A MODE REPLY 0 CNFBD /D/ 09MATERIAL FOR WHICH DESIGNED,PLATE PLATE MATERIAL FOR WHICH DESIGNED THE MATERIAL OF THE PLATE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AD09 CNFCA 19NUMBER,COLOR,MAXIMUM SAYBOLT CHROMOMETER MAXIMUM SAYBOLT CHROMOMETER COLOR NUMBER THE MAXIMUM SAYBOLT CHROMOMETER COLOR NUMBER OF THE ITEM. 1A MODE REPLY 0 CNFDB /D/ 10TEMP IN DEG FAHRENHEIT,MINIMUM,ANILINE POINT ANILINE POINT MINIMUM TEMP IN DEG FAHRENHEIT THE LOWEST TEMPERATURE AT WHICH AN ITEM IS MISCIBLE WITH ANILINE,EXPRESSED IN DEGREES FAHRENHEIT. 1B MODE REPLY 0 CNFFA 19NUMBER,BROMINE,MAXIMUM MAXIMUM BROMINE NUMBER THE MAXIMUM BROMINE NUMBER OF THE ITEM. 1A MODE REPLY 0 CNFGG /D/ 19SPEC/STD,OIL,LUBRICATING,COMPATIBLE ENGINE COMPATIBLE ENGINE LUBRICATING OIL SPEC/STD THE SPECIFICATION AND/OR STANDARD USED TO LIMIT THE ELEMENT,COMPOUND,OR MIXTURE OF THE COMPATIBLE ENGINE LUBRICATING OIL. FULL TEXT WRITE-IN 0 CNFHD /D/ 07FEATURE,SWELLING,SYNTHETIC RUBBER SYNTHETIC RUBBER SWELLING FEATURE AN INDICATION OF WHETHER OR NOT A SYNTHETIC RUBBER SWELLING FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CNFJF T10RANGE,PERCENTAGE,VOLUME SWELL VOLUME SWELL PERCENTAGE RANGE THE MINIMUM AND MAXIMUM VOLUME SWELL PERCENTAGE OF THE ITEM. 1F MODE REPLY 0 CNFKD 19PHASE,LIQUID LIQUID PHASE AN INDICATION OF THE PHASE OF LIQUID PROVIDED. SELECT REPLY CODE 10AL77 CNFLD 07RINSING RINSING AN INDICATION OF WHETHER OR NOT RINSING IS REQUIRED. SELECT REPLY CODE 10AE40 CNFMD 19NAME,LIQUID,RINSE RINSE LIQUID NAME THE NOMENCLATURE BY WHICH THE RINSE LIQUID IS IDENTIFIED. SELECT REPLY CODE 10AB75 CNFND /D/ 07RECTIFIER RECTIFIER AN INDICATION OF WHETHER OR NOT A RECTIFIER IS INCLUDED. SELECT REPLY CODE 10AA49 CNFPG /D/ 10PERCENTAGE BY WEIGHT,INGREDIENT,RECTIFYING RECTIFYING INGREDIENT PERCENTAGE BY WEIGHT THE RECTIFYING INGREDIENT AND ITS PERCENTAGE BY WEIGHT. FULL TEXT WRITE-IN 0 CNFQD 18TYPE FOR WHICH DESIGNED,PENETRANT PENETRANT TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF PENETRANT/S/ FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AF93 CNFRB /D/ 10TEMP IN DEG CELSIUS,MINIMUM,SLUSH POINT SLUSH POINT MINIMUM TEMP IN DEG CELSIUS THE SLUSH POINT MINIMUM TEMPERATURE FOR WHICH THE ITEM IS RATED,EXPRESSED IN DEGREES CELSIUS. 1B MODE REPLY 0 CNFSD 19CHEMICAL,MAJOR MAJOR CHEMICAL THE MAJOR CHEMICAL OF WHICH THE ITEM IS COMPOSED. SELECT REPLY CODE 10AG54 CNFTD /D/ 19CHEMICAL,MINOR MINOR CHEMICAL THE MINOR CHEMICAL OF WHICH THE ITEM IS COMPOSED. SELECT REPLY CODE 10AG54 CNFWD /D/ 07INHIBITOR INHIBITOR AN INDICATION OF WHETHER OR NOT AN INHIBITOR IS INCLUDED. SELECT REPLY CODE 10AA49 CNFXD 19COMPOSITION,INHIBITOR INHIBITOR COMPOSITION THE COMPOSITION OF THE INHIBITOR. SELECT REPLY CODE 10AG54 CNFYD /D/ 07CONDITIONER CONDITIONER AN INDICATION OF WHETHER OR NOT A CONDITIONER IS INCLUDED. SELECT REPLY CODE 10AA49 CNFZB 10WEIGHT PER TABLET IN MILLIGRAMS WEIGHT PER TABLET IN MILLIGRAMS THE MEASURED WEIGHT PER TABLET,EXPRESSED IN MILLIGRAMS. 1B MODE REPLY 0 CNGBB /D/ 10MILLIGRAMS OF CHEMICAL REQUIRED PER GALLON MILLIGRAMS OF CHEMICAL REQUIRED PER GALLON THE MILLIGRAMS OF CHEMICAL REQUIRED PER GALLON. 1B MODE REPLY 0 CNGCH /D/ 19INGREDIENT AND LOCATION INGREDIENT AND LOCATION THE INGREDIENT(S) OF WHICH THE ITEM IS COMPOSED AND THE LOCATION. 2D MODE REPLY 22AF113AJ91 CNGDB /D/ 10YIELD IN GALLONS,AGENT,DECONTAMINATING DECONTAMINATING AGENT YIELD IN GALLONS THE AMOUNT OF DECONTAMINATING AGENT YIELDED,EXPRESSED IN GALLONS. 1B MODE REPLY 0 CNGFJ 04LENGTH ACCOMMODATED,MAXIMUM,ENVELOPE ENVELOPE MAXIMUM LENGTH ACCOMMODATED THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF AN ENVELOPE THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 CNGGJ /D/ 04DEPTH ACCOMMODATED,ENVELOPE,MAXIMUM MAXIMUM ENVELOPE DEPTH ACCOMMODATED THE MAXIMUM MEASUREMENT BETWEEN SPECIFIED POINTS ON THE ENVELOPE ACCOMMODATED,IN DISTINCTION FROM HEIGHT. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/16/2024. 1D AND 1B MODE REPLY11AA05 CNGHJ 04THICKNESS ACCOMMODATED,ENVELOPE,MAXIMUM MAXIMUM ENVELOPE THICKNESS ACCOMMODATED THE MAXIMUM THICKNESS OF THE ENVELOPE ACCOMMODATED BY THE ITEM. 1D AND 1B MODE REPLY11AA05 CNGJF /D/T10RANGE,ENTERING,DOLLAR VALUE DOLLAR VALUE ENTERING RANGE THE MINIMUM AND MAXIMUM DOLLAR VALUES THAT CAN BE ENTERED. 1F MODE REPLY 0 CNGKB /D/ 10CAPACITY,VALUE,DOLLAR,DAILY TRANSACTION DAILY TRANSACTION DOLLAR VALUE CAPACITY THE DAILY TRANSACTION DOLLAR VALUE THAT CAN BE ENTERED. 1B MODE REPLY 0 CNGLD 18TYPE,MECHANISM MECHANISM TYPE INDICATES THE TYPE OF MECHANISM PROVIDED. SELECT REPLY CODE 10AK95 CNGMA 12QUANTITY,COUNTER,TRANSACTION TRANSACTION COUNTER QUANTITY THE NUMBER OF TRANSACTION COUNTERS PROVIDED. 1A MODE REPLY 0 CNGND /D/ 07REINFORCEMENT,FABRIC FABRIC REINFORCEMENT AN INDICATION OF WHETHER OR NOT A FABRIC REINFORCEMENT IS INCLUDED. SELECT REPLY CODE 10AA49 CNGPD /D/ 07FEATURE,THICKNESS,DOUBLE DOUBLE THICKNESS FEATURE AN INDICATION OF WHETHER OR NOT A DOUBLE THICKNESS FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CNGQD /D/ 07PIECE,SIDE/END,PROTECTIVE ADJOINED PROTECTIVE ADJOINED SIDE/END PIECE AN INDICATION OF WHETHER OR NOT A PROTECTIVE ADJOINED SIDE AND/OR END PIECE/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CNGRD /D/ 07CORD,LACING LACING CORD AN INDICATION OF WHETHER OR NOT A LACING CORD IS INCLUDED. SELECT REPLY CODE 10AA49 CNGSJ /D/ 04WIDTH,OVERALL,TOP SECTION TOP SECTION OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A TOP SECTION,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CNGTJ /D/ 04WIDTH,OVERALL,SIDE SECTION SIDE SECTION OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A SIDE SECTION,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CNGWA /D/ 12QUANTITY,TAPE,TYING TYING TAPE QUANTITY THE NUMBER OF TYING TAPES PROVIDED. 1A MODE REPLY 0 CNGXD /D/ 09MATERIAL,RETAINING,HEAT HEAT RETAINING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HEAT RETAINING MATERIAL IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CNGYD /D/ 14SHAPE,CUSHION CUSHION SHAPE THE PHYSICAL CONFIGURATION OF THE CUSHION. SELECT REPLY CODE 10AD07 CNGZJ 04DIAMETER,OVERALL,INFLATED CUSHION INFLATED CUSHION OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF THE INFLATED CUSHION. 1D AND 1B MODE REPLY11AA05 CNHBJ /D/ 04WIDTH,OVERALL,INFLATED CUSHION INFLATED CUSHION OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN INFLATED CUSHION,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CNHCJ 04LENGTH,OVERALL,INFLATED CUSHION INFLATED CUSHION OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE INFLATED CUSHIONS. 1D AND 1B MODE REPLY11AA05 CNHDD /D/ 07BULB,INFLATING INFLATING BULB AN INDICATION OF WHETHER OR NOT AN INFLATING BULB IS INCLUDED. SELECT REPLY CODE 10AA49 CNHFD /D/ 18TYPE FOR WHICH DESIGNED,CRUTCH CRUTCH TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF CRUTCH FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 CNHGJ /D/ 04LENGTH,OVERALL,OPEN/FLAT OPEN/FLAT OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM WHEN OPEN AND FLAT. 2D AND 1B MODE REPLY21AA051AC20 CNHHJ /D/ 04WIDTH,OVERALL,OPEN/FLAT OPEN/FLAT OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH WHEN THE ITEM IS OPEN AND FLAT. 2D AND 1B MODE REPLY21AA051AC20 CNHJD 11METHOD,CLOSURE,LINER LINER CLOSURE METHOD THE MEANS BY WHICH THE LINER IS CLOSED. SELECT REPLY CODE 10AE35 CNHKD /D/ 07CAP,SCREW SCREW CAP AN INDICATION OF WHETHER OR NOT A SCREW CAP IS INCLUDED. SELECT REPLY CODE 10AA49 CNHLD /D/ 07CHAIN,HEAD HEAD CHAIN AN INDICATION OF WHETHER OR NOT A HEAD CHAIN IS INCLUDED. SELECT REPLY CODE 10AA49 CNHMG /D/ 19TITLE,CHART CHART TITLE THE NAME DESIGNATION OF THE CHART. FULL TEXT WRITE-IN 0 CNHNA /D/ 12QUANTITY PER SHEET,CHART CHART QUANTITY PER SHEET THE NUMBER OF CHARTS PROVIDED PER SHEET. 1A MODE REPLY 0 CNHPD 01COLOR,PRINT PRINT COLOR THE HUE OR TINT OF THE PRINT. SELECT REPLY CODE 10AD06 CNHQJ 04LENGTH,OVERALL,CENTER OPENING CENTER OPENING OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE CENTER OPENING. 2D AND 1B MODE REPLY21AA051AC20 CNHRJ 04WIDTH,OVERALL,CENTER OPENING CENTER OPENING OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CENTER OPENING. 2D AND 1B MODE REPLY21AA051AC20 CNHSJ 04DIAMETER,OVERALL,CENTER OPENING CENTER OPENING OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF THE CENTER OPENING. 2D AND 1B MODE REPLY21AA051AC20 CNHTD /D/ 07LEGGINGS LEGGINGS AN INDICATION OF WHETHER OR NOT LEGGINGS ARE INCLUDED. SELECT REPLY CODE 10AA49 CNHWD /D/ 07COT,FINGER FINGER COT AN INDICATION OF WHETHER OR NOT A FINGER COT IS INCLUDED. SELECT REPLY CODE 10AA49 CNHXD /D/ 07CABLE,HORN HORN CABLE AN INDICATION OF WHETHER OR NOT A HORN CABLE IS INCLUDED. SELECT REPLY CODE 10AA49 CNHYD /D/ 07BUTTON,HORN HORN BUTTON AN INDICATION OF WHETHER OR NOT A HORN BUTTON IS INCLUDED. SELECT REPLY CODE 10AA49 CNHZA 12QUANTITY,DRUM,BRAKE BRAKE DRUM QUANTITY THE NUMBER OF BRAKE DRUMS PROVIDED. 1A MODE REPLY 0 CNJBD /D/ 18TYPE,MATERIAL,RIM RIM MATERIAL TYPE INDICATES THE TYPE OF MATERIAL USED FOR THE RIM. SELECT REPLY CODE 10AN48 CNJCD /D/ 18TYPE,MATERIAL,SPOKE SPOKE MATERIAL TYPE INDICATES THE TYPE OF MATERIAL USED FOR THE SPOKE. SELECT REPLY CODE 10AN48 CNJDD /D/ 18TYPE,MATERIAL,HUB HUB MATERIAL TYPE INDICATES THE TYPE OF MATERIAL USED FOR THE HUB. SELECT REPLY CODE 10AN48 CNJFD 18TYPE,CLAMP,LOCKING LOCKING CLAMP TYPE INDICATES THE TYPE OF LOCKING CLAMP PROVIDED. SELECT REPLY CODE 10AE36 CNJGJ 04DIAMETER,SPOKE SPOKE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SPOKE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CNJHJ 04WIDTH,SPOKE SPOKE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A SPOKE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CNJJJ 04THICKNESS,SPOKE SPOKE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A SPOKE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CNJKA 12QUANTITY,HOLE,LIGHTENING LIGHTENING HOLE QUANTITY THE NUMBER OF LIGHTENING HOLES PROVIDED. 1A MODE REPLY 0 CNJLD /D/ 07FEATURE,MOUNTING,LIGHTENING HOLE HUB CAP LIGHTENING HOLE HUB CAP MOUNTING FEATURE AN INDICATION OF WHETHER OR NOT A LIGHTENING HOLE HUB CAP MOUNTING FEATURE IS INCLUDED. PLEASE USE MRC CBBL FOR NIINS WERE ANSWERED WITH "INCLUDED" IN PLACE OF THIS CANCELLED MRC. SELECT REPLY CODE 10AA49 CNJMJ 04DIAMETER,MOUNTING,HUB CAP HUB CAP MOUNTING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HUB CAP MOUNTING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CNJND /D/ 07PLUMB BOB PLUMB BOB AN INDICATION OF WHETHER OR NOT A PLUMB BOB IS INCLUDED. SELECT REPLY CODE 10AA49 CNJPD /D/ 07CHARACTERISTIC,TYPE,RULE RULE TYPE CHARACTERISTIC AN INDICATION OF WHETHER OR NOT A RULE TYPE CHARACTERISTIC IS INCLUDED. SELECT REPLY CODE 10AA49 CNJQD 18TYPE,MARKING MARKING TYPE INDICATES THE TYPE OF MARKING/S/ PROVIDED. SELECT REPLY CODE 10AK39 CNJRD 18TYPE,END,HINGED HINGED END TYPE INDICATES THE TYPE OF HINGED END PROVIDED. SELECT REPLY CODE 10AK54 CNJSF T13THREAD RANGE PER INCH THREAD RANGE PER INCH THE MINIMUM AND MAXIMUM THREADS PER INCH THE ITEM IS CAPABLE OF MEASURING. 1F MODE REPLY 0 CNJTD /D/ 07STOP,RATCHET RATCHET STOP AN INDICATION OF WHETHER OR NOT A RATCHET STOP IS INCLUDED. SELECT REPLY CODE 10AA49 CNJWD /D/ 07FEATURE,DESIGN,TRANSFER TRANSFER DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A TRANSFER DESIGN FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CNJXD /D/ 07CONTROL,PRESSURE,PUSHBUTTON PUSHBUTTON PRESSURE CONTROL AN INDICATION OF WHETHER OR NOT A PUSHBUTTON PRESSURE CONTROL IS INCLUDED. SELECT REPLY CODE 10AA49 CNJYD /D/ 07INDICATOR,DIAL DIAL INDICATOR AN INDICATION OF WHETHER OR NOT A DIAL INDICATOR IS INCLUDED. SELECT REPLY CODE 10AA49 CNJZJ /D/ 10UNIT,GRADUATION,DIAL DIAL GRADUATION UNIT THE INCREMENT OF MEASURE REPRESENTED BY THE MARKING/S/ ON THE DIAL. 1D AND 1B MODE REPLY13AK09 CNKBA 12QUANTITY PER SET QUANTITY PER SET THE NUMBER OF ITEMS INCLUDED IN A SET. 1A MODE REPLY 0 CNKCG /D/ 19SIZE AND NATIONAL STOCK NUMBER,CALIPER CALIPER SIZE AND NATIONAL STOCK NUMBER AN INDICATION OF THE SIZE AND NATIONAL STOCK NUMBER OF THE CALIPER/S/. FULL TEXT WRITE-IN 0 CNKDG /D/ 19SIZE AND NATIONAL STOCK NUMBER,ROD,MEASURING,STANDARD MASTER DISK/END STANDARD MASTER DISK/END MEASURING ROD SIZE AND NATIONAL STOCK NUMBER AN INDICATION OF THE SIZE AND NATIONAL STOCK NUMBER OF THE STANDARD MASTER DISK AND/OR END MEASURING ROD PROVIDED. FULL TEXT WRITE-IN 0 CNKFG /D/ 10RANGE,DIAL,INDICATOR INDICATOR DIAL RANGE THE RANGE OF THE INDICATOR DIAL. FULL TEXT WRITE-IN 0 CNKGJ 10UNIT,GRADUATION,INDICATOR DIAL INDICATOR DIAL GRADUATION UNIT THE INCREMENT OF MEASURE REPRESENTED BY THE MARKING/S/ ON THE INDICATOR DIAL. 1D AND 1B MODE REPLY13AK09 CNKHD 07ADJUSTABILITY,DIAL,INDICATOR INDICATOR DIAL ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE INDICATOR DIAL IS ADJUSTABLE. SELECT REPLY CODE 10AB00 CNKJA 12QUANTITY,POINT,CONTACT CONTACT POINT QUANTITY THE NUMBER OF CONTACT POINTS PROVIDED. 1A MODE REPLY 0 CNKKD 11METHOD,OPERATION,CONTACT POINT CONTACT POINT OPERATION METHOD THE MEANS PROVIDED TO OPERATE THE CONTACT POINT(S). SELECT REPLY CODE 10AC58 CNKLD 18TYPE,HEAD,MEASURING MEASURING HEAD TYPE INDICATES THE TYPE OF MEASURING HEAD PROVIDED. SELECT REPLY CODE 10AK95 CNKMD 07INTERCHANGEABILITY,HEAD,MEASURING MEASURING HEAD INTERCHANGEABILITY AN INDICATION OF WHETHER OR NOT THE MEASURING HEAD IS INTERCHANGEABLE. SELECT REPLY CODE 10AM12 CNKNJ T10RANGE,GAGING,MEASURING HEAD MEASURING HEAD GAGING RANGE AN INDICATION OF THE MINIMUM AND MAXIMUM GAGING CAPACITY OF THE MEASURING HEAD. 1D AND 1F MODE REPLY11AA05 CNKPD /D/ 07DEVICE,LOCKING,MEASURING HEAD MEASURING HEAD LOCKING DEVICE AN INDICATION OF WHETHER OR NOT A MEASURING HEAD LOCKING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 CNKQD /D/ 07FEATURE,HARDENED/GROUND,MEASURING HEAD SLED MEASURING HEAD SLED HARDENED/GROUND FEATURE AN INDICATION OF WHETHER OR NOT A HARDENED AND GROUND FEATURE IS INCLUDED ON THE MEASURING HEAD SLED. SELECT REPLY CODE 10AA49 CNKRJ 04LENGTH,GAGING,MEASURING HEAD MEASURING HEAD GAGING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION THE MEASURING HEAD IS CAPABLE OF GAGING. 2D AND 1B MODE REPLY21AA051AC20 CNKSJ /D/ 04DISTANCE FROM CONTACT POINT TO HEAD END/PLUG DISTANCE FROM CONTACT POINT TO HEAD END/PLUG THE DISTANCE FROM THE CONTACT POINT TO THE HEAD END AND/OR PLUG. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNKTA /D/ 13SCREW THREAD QUANTITY PER INCH,FACILITY,MOUNTING MOUNTING FACILITY SCREW THREAD QUANTITY PER INCH THE NUMBER OF SCREW THREADS ON THE MOUNTING FACILITY PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CNKWJ 04DIAMETER,FACE,DIAL DIAL FACE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DIAL FACE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CNKXJ 10UNIT,GRADUATION,DIAL MINIMUM DIAL MINIMUM GRADUATION UNIT THE SMALLEST INCREMENT OF MEASURE REPRESENTED BY THE MARKING/S/ ON THE DIAL. 1D AND 1B MODE REPLY13AK09 CNKYD 07ADJUSTABILITY,DIAL DIAL ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE DIAL IS ADJUSTABLE. SELECT REPLY CODE 10AB00 CNKZF T10RANGE,COUNTER,REVOLUTION REVOLUTION COUNTER RANGE THE MINIMUM AND MAXIMUM NUMBER OF REVOLUTIONS THE ITEM WILL COUNT. 1F MODE REPLY 0 CNLBD /D/ 07FEATURE,MOVEMENT,REVERSE REVERSE MOVEMENT FEATURE AN INDICATION OF WHETHER OR NOT A REVERSE MOVEMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CNLCD 18TYPE,POINT,CONTACT CONTACT POINT TYPE INDICATES THE TYPE OF CONTACT POINT(S) PROVIDED. SELECT REPLY CODE 10AK54 CNLDA 12QUANTITY,ROD ROD QUANTITY THE NUMBER OF RODS PROVIDED. 1A MODE REPLY 0 CNLFG 03DESIGNATION,SIZE,ROD ROD SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE RODS ARE IDENTIFIED. FULL TEXT WRITE-IN 0 CNLGA 12QUANTITY,GROUP,BLADE BLADE GROUP QUANTITY THE NUMBER OF BLADE GROUPS PROVIDED. 1A MODE REPLY 0 CNLHD /D/ 07LOCK,BLADE BLADE LOCK AN INDICATION OF WHETHER OR NOT A BLADE LOCK IS INCLUDED. SELECT REPLY CODE 10AA49 CNLJD 13THREAD SERIES FOR WHICH DESIGNED THREAD SERIES FOR WHICH DESIGNED AN INDICATION OF THE THREAD SERIES FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AH06 CNLKA 13THREAD SIZE FOR WHICH DESIGNED,MAXIMUM MAXIMUM THREAD SIZE FOR WHICH DESIGNED AN INDICATION OF THE LARGEST THREAD FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 CNLLJ /D/T10RANGE,MEASUREMENT,JAW OUTSIDE JAW OUTSIDE MEASUREMENT RANGE THE MINIMUM AND MAXIMUM LIMITS OF THE JAW OUTSIDE MEASUREMENT. 1D AND 1F MODE REPLY11AA05 CNLMD 11METHOD,READING,INSIDE MEASUREMENT INSIDE MEASUREMENT READING METHOD THE MEANS USED TO READ THE INSIDE MEASUREMENT. SELECT REPLY CODE 10AJ12 CNLNJ /D/ 04LENGTH AND LOCATION,KNURL KNURL LENGTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNLPJ /D/ 04DIAMETER AND LOCATION,COUPLING COUPLING DIAMETER AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNLQJ /D/ 04DISTANCE AND LOCATION,SECOND HOLE CENTER TO SHAFT END SECOND HOLE CENTER TO SHAFT END DISTANCE AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNLRJ /D/ 04DISTANCE AND LOCATION,FIRST HOLE CENTER TO SHAFT END FIRST HOLE CENTER TO SHAFT END DISTANCE AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNLSJ /D/ 04DEPTH AND LOCATION,HOLE,SECOND SECOND HOLE DEPTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNLTJ /D/ 04DEPTH AND LOCATION,HOLE,FIRST FIRST HOLE DEPTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNLWJ /D/ 04DISTANCE AND LOCATION,SECOND KEYWAY CENTER TO SHAFT END SECOND KEYWAY CENTER TO SHAFT END DISTANCE AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNLXJ /D/ 04DEPTH AND LOCATION,KEYWAY,SECOND SECOND KEYWAY DEPTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNLYJ /D/ 04DISTANCE AND LOCATION,UNDERCUT CENTER TO SHAFT END UNDERCUT CENTER TO SHAFT END DISTANCE AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNLZJ /D/ 04HEIGHT ABOVE SHAFT AND LOCATION,KEY KEY HEIGHT ABOVE SHAFT AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNMBJ /D/ 04DEPTH AND LOCATION,HOLE HOLE DEPTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNMCJ /D/ 04WIDTH AND LOCATION,SLOT SLOT WIDTH AND LOCATION NONE. 3D AND 1B MODE REPLY31AA051AC203AJ91 CNMDJ /D/ 04ANGLE BETWEEN EXTERNAL KEYS IN DEG AND LOCATION ANGLE BETWEEN EXTERNAL KEYS IN DEG AND LOCATION NONE. 1D AND 1B MODE REPLY13AJ91 CNMFJ /D/ 04TAPER PER FOOT IN INCHES AND LOCATION TAPER PER FOOT IN INCHES AND LOCATION NONE. 1D AND 1B MODE REPLY13AJ91 CNMGJ /D/ 04ANGLE BETWEEN CENTERLINE OF HOLES IN DEG AND LOCATION ANGLE BETWEEN CENTERLINE OF HOLES IN DEG AND LOCATION NONE. 1D AND 1B MODE REPLY13AJ91 CNMHB /D/ 10FREQUENCY RATING IN HERTZ,INPUT INPUT FREQUENCY RATING IN HERTZ THE CYCLES PER SECOND /HERTZ/ OF THE INPUT ALTERNATING CURRENT. 1B MODE REPLY 0 CNMJJ /D/A19CHARACTERISTIC,END,SHAFT SHAFT END CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC(S) OF THE SHAFT END. 2D AND 1A MODE REPLY23AJ913AK54 CNMKA 03DESIGNATION,SIZE,WOODRUFF KEY WOODRUFF KEY SIZE DESIGNATION A NUMBER OR LETTER REPRESENTING THE SIZE OF A WOODRUFF KEY. 1A MODE REPLY 0 CNMLD /D/ 18TYPE,TACHOMETER TACHOMETER TYPE INDICATES THE TYPE OF TACHOMETER USED WITH THE ITEM. SELECT REPLY CODE 10AK54 CNMMA 03DESIGNATION,SIZE,FRAME FRAME SIZE DESIGNATION A DESIGNATION INDICATING THE FRAME SIZE BY WHICH THE ITEM IS IDENTIFIED. 1A MODE REPLY 0 CNMNJ 04HEIGHT,OVERALL,INCLOSURE INCLOSURE OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE INCLOSURE. 1D AND 1B MODE REPLY11AA05 CNMPJ 04LENGTH,OVERALL,INCLOSURE INCLOSURE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE INCLOSURE. 1D AND 1B MODE REPLY11AA05 CNMQJ 04WIDTH,OVERALL,INCLOSURE INCLOSURE OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE INCLOSURE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CNMRJ /D/ 04RADIUS,CUT CUT RADIUS A MEASUREMENT OF THE DISTANCE FROM THE CENTERLINE TO THE AXIS OF THE CUT. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 1D AND 1B MODE REPLY11AA05 CNMSD /D/ 07RECEPTACLE,CUTTINGS CUTTINGS RECEPTACLE AN INDICATION OF WHETHER OR NOT A CUTTINGS RECEPTACLE IS INCLUDED. SELECT REPLY CODE 10AA49 CNMXD /D/ 07SHELF,EXTENSION EXTENSION SHELF AN INDICATION OF WHETHER OR NOT AN EXTENSION SHELF IS INCLUDED. SELECT REPLY CODE 10AA49 CNMYJ /D/ 04LENGTH,PLATE,SPRING SPRING PLATE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SPRING PLATE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CNMZJ /D/ 04WIDTH,PLATE,SPRING SPRING PLATE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SPRING PLATE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CNNBD /D/ 14SHAPE,CROSS-SECTIONAL,SPOOL HOLDER SPOOL HOLDER CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE SPOOL HOLDER WHEN VIEWED IN CROSS-SECTION. SELECT REPLY CODE 10AD07 CNNDJ /D/ 04DIAMETER,OUTSIDE,MAXIMUM,SPOOL SPOOL MAXIMUM OUTSIDE DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SPOOL,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CNNFJ /D/ 04DIAMETER,OUTSIDE,MINIMUM,SPOOL SPOOL MINIMUM OUTSIDE DIAMETER THE MINIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SPOOL,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CNNGD /D/ 07LOCK,SPOOL SPOOL LOCK AN INDICATION OF WHETHER OR NOT A SPOOL LOCK IS INCLUDED. SELECT REPLY CODE 10AA49 CNNHA 12QUANTITY,SECTION,TOP TOP SECTION QUANTITY THE NUMBER OF TOP SECTIONS PROVIDED. 1A MODE REPLY 0 CNNJG /D/ 10RANGE,TILT,TOP TOP TILT RANGE THE MINIMUM AND MAXIMUM LIMITS WHICH THE TOP WILL TILT. FULL TEXT WRITE-IN 0 CNNKD /D/ 14SHAPE,DIAPHRAGM,BUCKY BUCKY DIAPHRAGM SHAPE THE PHYSICAL CONFIGURATION OF THE BUCKY DIAPHRAGM. SELECT REPLY CODE 10AD07 CNNLF /D/T10RANGE IN SECONDS,TIMER TIMER RANGE IN SECONDS THE MINIMUM AND MAXIMUM LIMITS OF THE TIMER,EXPRESSED IN SECONDS. 1F MODE REPLY 0 CNNMG /D/ 04SIZE,MAXIMUM,CASSETTE CASSETTE MAXIMUM SIZE THE MAXIMUM MEASUREMENTS OF THE CASSETTE. FULL TEXT WRITE-IN 0 CNNNJ 04RADIUS,CORNER,FIRST TIP INNER FIRST TIP INNER CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNNPJ 04RADIUS,CORNER,SECOND TIP INNER SECOND TIP INNER CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNNQJ /D/ 04RADIUS,CORNER,THIRD TIP INNER THIRD TIP INNER CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNNRJ /D/ 04RADIUS,CORNER,FOURTH TIP INNER FOURTH TIP INNER CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNNSJ 04RADIUS,CORNER,FIRST TIP OUTER FIRST TIP OUTER CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNNTJ /D/ 04RADIUS,CORNER,SECOND TIP OUTER SECOND TIP OUTER CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNNWJ /D/ 04RADIUS,CORNER,THIRD TIP OUTER THIRD TIP OUTER CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNNXJ /D/ 04RADIUS,CORNER,FOURTH TIP OUTER FOURTH TIP OUTER CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNNYJ 04DIAMETER,TIP,FIRST FIRST TIP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CNNZJ 04DIAMETER,TIP,SECOND SECOND TIP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPBJ 04DIAMETER,TIP,THIRD THIRD TIP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPCJ 04DIAMETER,TIP,FOURTH FOURTH TIP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPDJ 04LENGTH,TAPER,FIRST TIP FIRST TIP TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPFJ 04LENGTH,TAPER,SECOND TIP SECOND TIP TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPGJ 04LENGTH,TAPER,THIRD TIP THIRD TIP TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPHJ 04LENGTH,TAPER,FOURTH TIP FOURTH TIP TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPJJ /D/ 04LENGTH,TAPER,FIRST TIP INNER FIRST TIP INNER TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPKJ /D/ 04LENGTH,TAPER,SECOND TIP INNER SECOND TIP INNER TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPLJ /D/ 04LENGTH,TAPER,THIRD TIP INNER THIRD TIP INNER TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPMJ /D/ 04LENGTH,TAPER,FOURTH TIP INNER FOURTH TIP INNER TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPNJ /D/ 04LENGTH,TAPER,FIRST TIP OUTER FIRST TIP OUTER TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPPJ /D/ 04LENGTH,TAPER,SECOND TIP OUTER SECOND TIP OUTER TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPQJ /D/ 04LENGTH,TAPER,THIRD TIP OUTER THIRD TIP OUTER TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPRJ /D/ 04LENGTH,TAPER,FOURTH TIP OUTER FOURTH TIP OUTER TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPSJ 04THICKNESS,TIP,FIRST FIRST TIP THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPTJ 04THICKNESS,TIP,SECOND SECOND TIP THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPWJ 04THICKNESS,TIP,THIRD THIRD TIP THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPXJ 04THICKNESS,TIP,FOURTH FOURTH TIP THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPYJ 04HEIGHT,FLANGE,FIRST TIP FIRST TIP FLANGE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CNPZJ 04HEIGHT,FLANGE,SECOND TIP SECOND TIP FLANGE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CNQBJ /D/ 04HEIGHT,FLANGE,THIRD TIP THIRD TIP FLANGE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CNQCJ /D/ 04HEIGHT,FLANGE,FOURTH TIP FOURTH TIP FLANGE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CNQDJ 04WIDTH,FLANGE,FIRST TIP FIRST TIP FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CNQFJ 04WIDTH,FLANGE,SECOND TIP SECOND TIP FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CNQGJ /D/ 04WIDTH,FLANGE,THIRD TIP THIRD TIP FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CNQHJ /D/ 04WIDTH,FLANGE,FOURTH TIP FOURTH TIP FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CNQJD 19RELATIONSHIP TO FIRST TIP,SECOND TIP SECOND TIP RELATIONSHIP TO FIRST TIP AN INDICATION OF WHETHER OR NOT THE SECOND TIP IS IDENTICAL TO THE FIRST TIP. SELECT REPLY CODE 10AF63 CNQKL 16STYLE,TIP,SECOND SECOND TIP STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SECOND TIP. 1L MODE REPLY 0 CNQLD 19RELATIONSHIP TO PRECEDING TIPS,THIRD TIP THIRD TIP RELATIONSHIP TO PRECEDING TIPS AN INDICATION OF WHETHER OR NOT THE THIRD TIP IS IDENTICAL TO THE PRECEDING TIPS. SELECT REPLY CODE 10AF63 CNQML 16STYLE,TIP,THIRD THIRD TIP STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THIRD TIP. 1L MODE REPLY 0 CNQND 19RELATIONSHIP TO PRECEDING TIPS,FOURTH TIP FOURTH TIP RELATIONSHIP TO PRECEDING TIPS AN INDICATION OF WHETHER OR NOT THE FOURTH TIP IS IDENTICAL TO THE PRECEDING TIPS. SELECT REPLY CODE 10AF63 CNQPL 16STYLE,TIP,FOURTH FOURTH TIP STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FOURTH TIP. 1L MODE REPLY 0 CNQQD /D/ 18TYPE ACCOMMODATED,TEETH TEETH TYPE ACCOMMODATED INDICATES THE TYPE OF TEETH THE ITEM IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AK95 CNQRJ 10VALUE PER FUNCTION,CAPACITANCE CAPACITANCE VALUE PER FUNCTION THE RELATIVE LEVEL OF THE QUANTITY OF ELECTRICAL CHARGE AT A GIVEN POTENTIAL WHICH THE CAPACITOR IS CAPABLE OF RECEIVING AND STORING PER FUNCTION. 2D AND 1B MODE REPLY21AC772AH19 CNQSJ T10TOLERANCE PER FUNCTION IN PERCENT,CAPACITANCE CAPACITANCE TOLERANCE PER FUNCTION IN PERCENT THE LIMITS OF PERMISSIBLE DEVIATION OF CAPACITANCE VALUE PER FUNCTION OF AN ITEM FROM ITS RATED VALUE,EXPRESSED IN PERCENT. 1D AND 1F MODE REPLY12AH19 CNQTJ 10VOLTAGE RATING PER FUNCTION IN VOLTS,DC DC VOLTAGE RATING PER FUNCTION IN VOLTS THE DIRECT CURRENT VOLTAGE PER FUNCTION FOR WHICH THE ITEM IS RATED,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY12AH19 CNQWJ 10VOLTAGE RATING PER FUNCTION IN VOLTS,AC AC VOLTAGE RATING PER FUNCTION IN VOLTS THE ALTERNATING CURRENT VOLTAGE PER FUNCTION FOR WHICH THE ITEM IS RATED,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY12AH19 CNQXJ 10RESISTANCE PER FUNCTION,ELECTRICAL ELECTRICAL RESISTANCE PER FUNCTION A MEASURE OF THE OPPOSITION TO THE FLOW OF ELECTRICAL CURRENT PER FUNCTION. 2D AND 1B MODE REPLY21AA572AH19 CNQYJ T10TOLERANCE PER FUNCTION IN PERCENT,RESISTANCE RESISTANCE TOLERANCE PER FUNCTION IN PERCENT THE PERMISSIBLE VARIATION IN THE ELECTRICAL RESISTANCE VALUE OF AN ITEM FROM ITS RATED VALUE PER FUNCTION,EXPRESSED IN PERCENT. 1D AND 1F MODE REPLY12AH19 CNQZJ 10DISSIPATION RATING PER FUNCTION IN WATTS,POWER,RESISTOR RESISTOR POWER DISSIPATION RATING PER FUNCTION IN WATTS THE MAXIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY A RESISTOR PER FUNCTION,EXPRESSED IN WATTS. 1D AND 1B MODE REPLY12AH19 CNRBG 19CONSTRUCTION CONSTRUCTION AN INDICATION OF THE STRUCTURAL CHARACTERISTICS OF THE ITEM. FULL TEXT WRITE-IN 0 CNRCD 18TYPE FOR WHICH DESIGNED,SHAFT SHAFT TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF SHAFT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AF58 CNRDD /D/ 07FEATURE,INTERCHANGEABILITY DURING OPERATION,CHUCK CHUCK INTERCHANGEABILITY DURING OPERATION FEATURE AN INDICATION OF WHETHER OR NOT A FEATURE IS INCLUDED FOR THE CHUCK TO BE INTERCHANGEABLE DURING OPERATION. SELECT REPLY CODE 10AA49 CNRFJ 04DIAMETER,BRISTLE BRISTLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BRISTLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CNRGJ 04LENGTH,PORTION,EXPOSED BRISTLE EXPOSED BRISTLE PORTION LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE EXPOSED BRISTLE PORTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CNRHJ /D/ 04DISTANCE BETWEEN DIVIDERS DISTANCE BETWEEN DIVIDERS THE DISTANCE MEASURED BETWEEN THE DIVIDERS ON AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 CNRJD /D/ 07SHIELD,TIP TIP SHIELD AN INDICATION OF WHETHER OR NOT A TIP SHIELD IS INCLUDED. SELECT REPLY CODE 10AA49 CNRKD /D/ 07REMOVABILITY,TRAY TRAY REMOVABILITY AN INDICATION OF WHETHER OR NOT THE TRAY IS REMOVABLE. SELECT REPLY CODE 10AC29 CNRLJ /D/ 10STRENGTH,BURSTING,WARP MATERIAL WARP MATERIAL BURSTING STRENGTH THE MINIMUM FORCE REQUIRED TO RUPTURE THE WARP MATERIAL. 1D AND 1B MODE REPLY12AG67 CNRMJ /D/ 10STRENGTH,BURSTING,FILLING MATERIAL FILLING MATERIAL BURSTING STRENGTH THE MINIMUM FORCE REQUIRED TO RUPTURE THE FILLING MATERIAL. 1D AND 1B MODE REPLY12AG67 CNRNA 12QUANTITY FOR WHICH DESIGNED,SEAT,MOUNTING POST MOUNTING POST SEAT QUANTITY FOR WHICH DESIGNED THE NUMBER OF SEATS FOR WHICH THE MOUNTING POST IS DESIGNED. 1A MODE REPLY 0 CNRPD /D/ 09MATERIAL,ARM,SEAT SUPPORT SEAT SUPPORT ARM MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SEAT SUPPORT ARM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CNRQD /D/ 17SURFACE TREATMENT,ARM,SEAT SUPPORT SEAT SUPPORT ARM SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SEAT SUPPORT ARM SURFACE. SELECT REPLY CODE 10AD09 CNRRA /D/ 12QUANTITY,SET,ANTERIOR LOWER TEETH ANTERIOR LOWER TEETH SET QUANTITY THE NUMBER OF ANTERIOR LOWER TEETH SETS PROVIDED. 1A MODE REPLY 0 CNRSA /D/ 12QUANTITY,SET,ANTERIOR UPPER TEETH ANTERIOR UPPER TEETH SET QUANTITY THE NUMBER OF ANTERIOR UPPER TEETH SETS PROVIDED. 1A MODE REPLY 0 CNRTA /D/ 12QUANTITY,SET,POSTERIOR UPPER TEETH POSTERIOR UPPER TEETH SET QUANTITY THE NUMBER OF POSTERIOR UPPER TEETH SETS PROVIDED. 1A MODE REPLY 0 CNRWA /D/ 12QUANTITY,SET,POSTERIOR LOWER TEETH POSTERIOR LOWER TEETH SET QUANTITY THE NUMBER OF POSTERIOR LOWER TEETH SETS PROVIDED. 1A MODE REPLY 0 CNRXD /D/ 07HOLDER,LABEL,INDIVIDUAL,DRAWER DRAWER INDIVIDUAL LABEL HOLDER AN INDICATION OF WHETHER OR NOT DRAWER INDIVIDUAL LABEL HOLDERS ARE INCLUDED. SELECT REPLY CODE 10AA49 CNRYJ /D/A18TYPE AND QUANTITY,LINER,DRAWER DRAWER LINER TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF DRAWER LINERS PROVIDED. 1D AND 1A MODE REPLY13AK95 CNRZA /D/ 12QUANTITY ACCOMMODATED,SET,TEETH,LINER LINER TEETH SET QUANTITY ACCOMMODATED THE NUMBER OF TEETH SETS ACCOMMODATED IN EACH LINER. 1A MODE REPLY 0 CNSBD /D/ 07COVERING,LAMINATE,PLASTIC,DOOR MATERIAL DOOR MATERIAL PLASTIC LAMINATE COVERING AN INDICATION OF WHETHER OR NOT A DOOR MATERIAL PLASTIC LAMINATE COVERING IS INCLUDED. SELECT REPLY CODE 10AA49 CNSCD /D/ 07DESIGN,SEPARATED BY RAISING COVER,TRAYS TRAYS SEPARATED BY RAISING COVER DESIGN AN INDICATION OF WHETHER OR NOT A DESIGN IS INCLUDED TO SEPARATE THE TRAYS BY RAISING THE COVER. SELECT REPLY CODE 10AA49 CNSDD /D/ 07FEATURE,COMPARTMENTAL COMPARTMENTAL FEATURE AN INDICATION OF WHETHER OR NOT A COMPARTMENTAL FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CNSFD /D/ 07CARD,REPLACEMENT REPLACEMENT CARD AN INDICATION OF WHETHER OR NOT A REPLACEMENT CARD(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CNSGD /D/ 07RACK,BOTTLE BOTTLE RACK AN INDICATION OF WHETHER OR NOT A BOTTLE RACK IS INCLUDED. SELECT REPLY CODE 10AA49 CNSHD /D/ 11METHOD,ATTACHMENT,LIGHT LIGHT ATTACHMENT METHOD THE MEANS USED TO ATTACH THE ITEM TO A LIGHT. SELECT REPLY CODE 10AB47 CNSJD /D/ 11METHOD,ATTACHMENT,TRIPOD TRIPOD ATTACHMENT METHOD THE MEANS USED TO ATTACH THE ITEM TO A TRIPOD. SELECT REPLY CODE 10AB47 CNSKJ 04LENGTH,OVERALL,BACKREST BACKREST OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BACKREST. 2D AND 1B MODE REPLY21AA051AC20 CNSLJ 04WIDTH,OVERALL,BACKREST BACKREST OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BACKREST,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CNSMJ 04DIAMETER,SEAT SEAT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR SEAT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CNSNA 12QUANTITY,FACILITY,RIM FASTENING RIM FASTENING FACILITY QUANTITY THE NUMBER OF FACILITIES FOR FASTENING THE RIM. 1A MODE REPLY 0 CNSPA /D/ 13THREAD SIZE,FACILITY,RIM FASTENING RIM FASTENING FACILITY THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A RIM FASTENING FACILITY. PLEASE USE MRC ABUJ IN PLACE OF THIS CANCELLED MRC. 1A MODE REPLY 0 CNSQD 13THREAD DIRECTION,FACILITY,RIM FASTENING RIM FASTENING FACILITY THREAD DIRECTION THE DIRECTION OF THE THREAD FOR A RIM FASTENING FACILITY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 CNSRJ 04LENGTH,STUD,RIM FASTENING RIM FASTENING STUD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE RIM FASTENING STUD,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CNSSJ 04DIAMETER,CIRCLE,BOLT,MOUNTING FACILITY MOUNTING FACILITY BOLT CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING FACILITY BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CNSTD /D/ 07MOTOR,SEALED SEALED MOTOR AN INDICATION OF WHETHER OR NOT A SEALED MOTOR IS PROVIDED. SELECT REPLY CODE 10AB22 CNSWD /D/ 07FEATURE,COMBINATION,MOTOR/PUMP HOUSING MOTOR/PUMP HOUSING COMBINATION FEATURE AN INDICATION OF WHETHER OR NOT A MOTOR AND/OR PUMP HOUSING COMBINATION FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CNSXH /D/ 09MATERIAL AND LOCATION,COATING COATING MATERIAL AND LOCATION THE COATING MATERIAL AND THE LOCATION OF THE ITEM TO WHICH A COATING HAS BEEN APPLIED,EXCLUDING ANY SURFACE TREATMENT. 2D MODE REPLY 26AD093AJ91 CNSYD 18TYPE,FABRIC,COVER COVER FABRIC TYPE INDICATES THE TYPE OF COVER FABRIC PROVIDED. SELECT REPLY CODE 10AF82 CNSZD /D/ 09MATERIAL,PADDING,INNER INNER PADDING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INNER PADDING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CNTBD /D/ 01COLOR,MARBLEIZED MARBLEIZED COLOR THE HUE OR TINT WHICH COMPRISES THE MARBLED EFFECT. SELECT REPLY CODE 10AD06 CNTCD /D/ 07FEATURE,DESIGN,POUCH POUCH DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A POUCH DESIGN FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CNTDD /D/ 18TYPE,BOTTOM,POUCH POUCH BOTTOM TYPE INDICATES THE TYPE OF BOTTOM ON THE POUCH. SELECT REPLY CODE 10AJ17 CNTFD /D/ 11METHOD,CLOSURE,OPEN BOTTOM POUCH OPEN BOTTOM POUCH CLOSURE METHOD THE MEANS PROVIDED TO CLOSE THE OPEN BOTTOM OF THE POUCH. SELECT REPLY CODE 10AE35 CNTGD 18TYPE,FACE,POUCH POUCH FACE TYPE INDICATES THE TYPE OF FACE ON THE POUCH. SELECT REPLY CODE 10AK54 CNTHJ 04DIAMETER,OPENING,CENTER CENTER OPENING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CENTER OPENING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CNTJJ 10CAPACITY,LOAD,RATED RATED LOAD CAPACITY THE LOAD CAPACITY OF THE ITEM AS RATED BY THE MANUFACTURER. 1D AND 1B MODE REPLY12AG67 CNTKD 08LOCATION,AXLE,DRIVE DRIVE AXLE LOCATION INDICATES THE LOCATION OF THE DRIVE AXLE ON THE ITEM. SELECT REPLY CODE 10AJ91 CNTLD /D/ 18TYPE,DRIVE,AXLE AXLE DRIVE TYPE INDICATES THE TYPE OF MECHANISM USED TO TRANSMIT POWER AT THE REAR WHEELS. SELECT REPLY CODE 10AG25 CNTMA 12QUANTITY,SPEED,AXLE AXLE SPEED QUANTITY THE NUMBER OF REAR AXLE SPEEDS. 1A MODE REPLY 0 CNTND /D/ 07UNIT,DIVIDER,POWER POWER DIVIDER UNIT AN INDICATION OF WHETHER OR NOT A POWER DIVIDER UNIT IS INCLUDED. SELECT REPLY CODE 10AA49 CNTPD /D/ 18TYPE,MECHANISM,ENGAGING,FRONT AXLE FRONT AXLE ENGAGING MECHANISM TYPE INDICATES THE TYPE OF FRONT AXLE ENGAGING MECHANISM. SELECT REPLY CODE 10AK54 CNTQD 18TYPE,MOUNTING,REAR WHEEL REAR WHEEL MOUNTING TYPE INDICATES THE TYPE OF REAR WHEEL MOUNTING PROVIDED. SELECT REPLY CODE 10AH86 CNTRJ 10WHEELBASE,NOMINAL NOMINAL WHEELBASE THE NOMINAL DISTANCE BETWEEN FRONT AND REAR AXLES OR BETWEEN THE FRONT AXLE AND CENTER POINT OF REAR MULTI-AXLE ASSEMBLIES/TANDEMS,TRIDEMS,ETC./. 1D AND 1B MODE REPLY11AA05 CNTSJ 04WIDTH,NOMINAL,FRONT WHEEL TREAD FRONT WHEEL TREAD NOMINAL WIDTH THE NOMINAL TREAD DISTANCE BETWEEN THE CENTERS OF THE FRONT WHEELS. 1D AND 1B MODE REPLY11AA05 CNTTJ 04WIDTH,NOMINAL,REAR WHEEL TREAD REAR WHEEL TREAD NOMINAL WIDTH THE NOMINAL TREAD DISTANCE BETWEEN THE CENTERS OF THE REAR WHEELS. 1D AND 1B MODE REPLY11AA05 CNTWD /D/ 07FEATURE,DESIGN,MULTIFUEL MULTIFUEL DESIGN FEATURE AN INDICATION OF WHETHER OR NOT A MULTIFUEL DESIGN FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC CBBL IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 CNTXA 12QUANTITY,RANGE,FORWARD SPEED FORWARD SPEED RANGE QUANTITY THE NUMBER OF FORWARD SPEED RANGES PROVIDED. 1A MODE REPLY 0 CNTYD 18TYPE,ADJUNCT,TRANSMISSION TRANSMISSION ADJUNCT TYPE INDICATES THE TYPE OF ADJUNCT TRANSMISSION PROVIDED. SELECT REPLY CODE 10AM54 CNTZA 12QUANTITY,SPEED,TRANSMISSION ADJUNCT TRANSMISSION ADJUNCT SPEED QUANTITY THE NUMBER OF SPEEDS PROVIDED IN THE TRANSMISSION ADJUNCT. 1A MODE REPLY 0 CNWBD 08LOCATION,WINCH WINCH LOCATION INDICATES THE LOCATION OF THE WINCH ON THE ITEM. SELECT REPLY CODE 10AJ91 CNWCD 18TYPE,WINCH WINCH TYPE INDICATES THE TYPE OF WINCH PROVIDED ON THE ITEM. SELECT REPLY CODE 10AK54 CNWDH 18TYPE,BOOM BOOM TYPE INDICATES THE TYPE OF BOOM PROVIDED ON THE ITEM. 2D MODE REPLY 23AK542AL76 CNWFJ 04LENGTH,MAXIMUM,BOOM BOOM MAXIMUM LENGTH A MEASUREMENT OF THE MAXIMUM LENGTH OF THE BOOM. 1D AND 1B MODE REPLY11AA05 CNWGD 05DIRECTION,OPERATIONAL,BOOM BOOM OPERATIONAL DIRECTION THE DIRECTION IN WHICH THE BOOM MOVES FOR OPERATION. SELECT REPLY CODE 10AA38 CNWHB 04ANGLE IN DEG,SWING,MINIMUM MINIMUM SWING ANGLE IN DEG THE MINIMUM ANGLE THE ITEM CAN SWING,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CNWJD 18TYPE,OPERATION,CRANE CRANE OPERATION TYPE INDICATES THE TYPE OF MECHANISM USED IN OPERATION OF THE CRANE. SELECT REPLY CODE 10AK54 CNWKA 12QUANTITY,HOIST HOIST QUANTITY THE NUMBER OF HOISTS PROVIDED ON THE ITEM. 1A MODE REPLY 0 CNWLJ 04HEIGHT,NOMINAL,HOIST MOUNTING HOIST MOUNTING NOMINAL HEIGHT THE NOMINAL HEIGHT FOR MOUNTING THE HOIST. 1D AND 1B MODE REPLY11AA05 CNWMD 11METHOD,MOUNTING,HOIST HOIST MOUNTING METHOD THE MEANS IN WHICH THE HOIST IS MOUNTED ON THE ITEM. SELECT REPLY CODE 10AM39 CNWNG /D/ 18TYPE,COUNTER,TRANSACTION TRANSACTION COUNTER TYPE INDICATES THE TYPE OF TRANSACTION COUNTER/S/ PROVIDED. FULL TEXT WRITE-IN 0 CNWPD /D/ 07SLIP,AUDIT,DETAILED DETAILED AUDIT SLIP AN INDICATION OF WHETHER OR NOT A DETAILED AUDIT SLIP IS PROVIDED. SELECT REPLY CODE 10AB22 CNWQA 12QUANTITY,DRAWER,MONEY MONEY DRAWER QUANTITY THE NUMBER OF MONEY DRAWERS PROVIDED. 1A MODE REPLY 0 CNWRA 12QUANTITY,COMPARTMENT,FIXED COIN FIXED COIN COMPARTMENT QUANTITY THE NUMBER OF FIXED COIN COMPARTMENTS PROVIDED. 1A MODE REPLY 0 CNWSA 12QUANTITY,COMPARTMENT,FIXED BILL FIXED BILL COMPARTMENT QUANTITY THE NUMBER OF FIXED BILL COMPARTMENTS PROVIDED. 1A MODE REPLY 0 CNWTA 12QUANTITY,COMPARTMENT,COIN,REMOVABLE TRAY REMOVABLE TRAY COIN COMPARTMENT QUANTITY THE NUMBER OF COIN COMPARTMENTS PROVIDED IN A REMOVABLE TRAY. 1A MODE REPLY 0 CNWWA 12QUANTITY,COMPARTMENT,BILL,REMOVABLE TRAY REMOVABLE TRAY BILL COMPARTMENT QUANTITY THE NUMBER OF BILL COMPARTMENTS PROVIDED IN A REMOVABLE TRAY. 1A MODE REPLY 0 CNWXB /D/ 10CAPACITY,VALUE,MAXIMUM DOLLAR MAXIMUM DOLLAR VALUE CAPACITY THE MAXIMUM DOLLAR VALUE THAT CAN BE ENTERED. 1B MODE REPLY 0 CNWYA 10CAPACITY,ENTERING,DIGIT DIGIT ENTERING CAPACITY THE NUMBER OF DIGITS THAT CAN BE ENTERED. 1A MODE REPLY 0 CNWZA /D/ 10CAPACITY,UNIT,MAXIMUM,INDICATING DIAL INDICATING DIAL MAXIMUM UNIT CAPACITY THE MAXIMUM NUMBER OF UNITS THAT CAN BE REGISTERED ON THE INDICATING DIAL. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/16/2024. 1A MODE REPLY 0 CNXBG 19LEGEND,PUNCHED PUNCHED LEGEND THE INFORMATION PUNCHED BY THE ITEM. FULL TEXT WRITE-IN 0 CNXCD 19CAPABILITY,SPACING SPACING CAPABILITY AN INDICATION OF THE SPACING CAPABILITY/IES/ OF THE ITEM. SELECT REPLY CODE 10AK54 CNXDD /D/ 07FEATURE,CALENDAR CALENDAR FEATURE AN INDICATION OF WHETHER OR NOT A CALENDAR FEATURE IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 CNXFD 07REMOVABILITY,REGISTER REGISTER REMOVABILITY AN INDICATION OF WHETHER OR NOT THE REGISTER(S) IS REMOVABLE. SELECT REPLY CODE 10AB00 CNXGB 10CAPACITY,TOTALING,REGISTER REGISTER TOTALING CAPACITY THE MAXIMUM TOTALING CAPACITY OF THE ITEM. 1B MODE REPLY 0 CNXHA 12QUANTITY,COLUMN COLUMN QUANTITY THE NUMBER OF COLUMNS PROVIDED. 1A MODE REPLY 0 CNXJD 18TYPE,FEED,CARRIAGE CARRIAGE FEED TYPE INDICATES THE TYPE OF CARRIAGE FEED PROVIDED. SELECT REPLY CODE 10AK54 CNXKD /D/ 07PLATEN,SPLIT SPLIT PLATEN AN INDICATION OF WHETHER OR NOT A SPLIT PLATEN IS PROVIDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AB22 CNXLG /D/ 08LOCATION,SPLIT SPLIT LOCATION INDICATES THE LOCATION OF THE SPLIT. FULL TEXT WRITE-IN 0 CNXMD /D/ 07STOP,TAB,ADJUSTABLE COLUMN SELECTING ADJUSTABLE COLUMN SELECTING TAB STOP AN INDICATION OF WHETHER OR NOT AN ADJUSTABLE TAB STOP/S/ FOR COLUMN SELECTION IS PROVIDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AB22 CNXND /D/ 07TABULATION,SKIP,SELECTIVE,AUTOMATIC AUTOMATIC SELECTIVE SKIP TABULATION AN INDICATION OF WHETHER OR NOT AUTOMATIC SELECTIVE SKIP TABULATION IS PROVIDED. IF INCLUDED PLEASE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AB22 CNXPD /D/ 07HOLDER,PAPER,ROLL ROLL PAPER HOLDER AN INDICATION OF WHETHER OR NOT A HOLDER FOR ROLL PAPER IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AA49 CNXQJ 04LENGTH,BOOM BOOM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BOOM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CNXRD 11METHOD,OPERATION,CARRIAGE FEED CARRIAGE FEED OPERATION METHOD THE MEANS USED TO OPERATE THE CARRIAGE FEED. SELECT REPLY CODE 10AC58 CNXSJ 10POWER RATING POWER RATING THE AMOUNT OF ELECTRICAL ENERGY THAT CAN BE DISSIPATED. 1D AND 1B MODE REPLY11AC33 CNXTD 18TYPE,STROKE,ACTUATOR ACTUATOR STROKE TYPE THE MOVEMENT OF THE ACTUATOR WHEN FORCE IS APPLIED. SELECT REPLY CODE 10AC82 CNXWJ 10FORCE DELIVERED,LINEAR LINEAR FORCE DELIVERED THE AMOUNT OF LINEAR FORCE DELIVERED. 1D AND 1B MODE REPLY12AG67 CNXXD 18TYPE,CONNECTION,POWER TAKEOFF POWER TAKEOFF CONNECTION TYPE INDICATES THE TYPE OF MEANS PROVIDED FOR CONNECTION OF THE POWER TAKEOFF. SELECT REPLY CODE 10AA78 CNXYJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,CONNECTION,POWER TAKEOFF POWER TAKEOFF CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE POWER TAKEOFF CONNECTION THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AH06 CNXZB /D/ 10STROKE IN ANGULAR DEG,ROTARY,ENERGIZING ENERGIZING ROTARY STROKE IN ANGULAR DEG THE ANGULAR ROTARY STROKE OF TRAVEL FROM THE DE-ENERGIZED TO THE ENERGIZED POSITION,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CNYBJ /D/ 10TORQUE,END END TORQUE THE ROTATIONAL FORCE MEASURED AT THE END OF ANGULAR TRAVEL. 1D AND 1B MODE REPLY11AA56 CNYCJ /D/ 10TORQUE,STARTING STARTING TORQUE THE ROTATIONAL FORCE MEASURED AT THE BEGINNING OF ANGULAR TRAVEL. 1D AND 1B MODE REPLY11AA56 CNYDJ 04LENGTH,MAXIMUM,ENERGIZING STROKE ENERGIZING STROKE MAXIMUM LENGTH THE MAXIMUM LINEAR TRAVEL FROM THE DE-ENERGIZED TO THE ENERGIZED POSITION. 1D AND 1B MODE REPLY11AA05 CNYFJ A19FACILITY AND QUANTITY,COUPLING,PLATE PLATE COUPLING FACILITY AND QUANTITY THE PLATE COUPLING FACILITY PROVIDED FOR ATTACHMENT,AND THE NUMBER OF EACH. 1D AND 1A MODE REPLY13AM39 CNYGJ 04DIAMETER,FACILITY,PLATE COUPLING PLATE COUPLING FACILITY DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PLATE COUPLING FACILITY,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CNYHJ 04DIAMETER,HOLE,POWER TAKEOFF CONNECTION POWER TAKEOFF CONNECTION HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A POWER TAKEOFF CONNECTION HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CNYJJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,FACILITY,PLATE COUPLING PLATE COUPLING FACILITY THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE PLATE COUPLING FACILITY THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AH06 CNYKJ /D/ 04LENGTH,STUD,PLATE COUPLING PLATE COUPLING STUD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE STUD PROVIDED ON THE PLATE COUPLING. 2D AND 1B MODE REPLY21AA051AC20 CNYLJ 04WIDTH,OVERALL,TOP TOP OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TOP,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CNYMJ 04RADIUS,FACILITY,PLATE COUPLING PLATE COUPLING FACILITY RADIUS THE DISTANCE FROM A CENTER POINT OF THE PLATE COUPLING FACILITY TO AN AXIS OF ROTATION. 2D AND 1B MODE REPLY21AA051AC20 CNYNJ /D/ 10SPAN,NOMINAL,RAIL RAIL NOMINAL SPAN THE NOMINAL DISTANCE BETWEEN THE RAILS. 1D AND 1B MODE REPLY11AA05 CNYPJ 04DISTANCE,TRAVEL,MAXIMUM,HOIST HOIST MAXIMUM TRAVEL DISTANCE THE MAXIMUM MEASURED DISTANCE THE HOIST TRAVELS. 1D AND 1B MODE REPLY11AA05 CNYQJ 10CAPACITY RATING,LIFTING,LOAD LOAD LIFTING CAPACITY RATING THE LOAD LIFTING CAPABILITY OF THE ITEM AS SPECIFIED BY THE MANUFACTURER. 1D AND 1B MODE REPLY12AG67 CNYRD 11METHOD,LIFTING,LOAD LOAD LIFTING METHOD THE MEANS BY WHICH THE LOAD IS LIFTED. SELECT REPLY CODE 10AD28 CNYSD 18TYPE,CAB CAB TYPE INDICATES THE TYPE OF CAB MOUNTED ON THE CHASSIS INDEPENDENT OF BODY AND/OR SPECIALIZED EQUIPMENT. SELECT REPLY CODE 10AK54 CNYTD 18TYPE,ROOF,CAB CAB ROOF TYPE INDICATES THE TYPE OF COVERING FURNISHED FOR THE CAB. SELECT REPLY CODE 10AK54 CNYWD 11METHOD,ACTUATION,BRAKE BRAKE ACTUATION METHOD THE MEANS BY WHICH THE BRAKES ARE ACTUATED. SELECT REPLY CODE 10AK88 CNYXD 18TYPE,COMPARTMENT,STORAGE STORAGE COMPARTMENT TYPE INDICATES THE TYPE OF STORAGE COMPARTMENT PROVIDED. SELECT REPLY CODE 10AK54 CNYYD 19ACCESSIBILITY,COMPARTMENT,STORAGE STORAGE COMPARTMENT ACCESSIBILITY AN INDICATION OF THE MEANS OF ACCESS TO THE STORAGE COMPARTMENT. SELECT REPLY CODE 10AM20 CNYZD 08LOCATION,COMPARTMENT,STORAGE STORAGE COMPARTMENT LOCATION INDICATES THE LOCATION OF THE STORAGE COMPARTMENT/S/. SELECT REPLY CODE 10AJ91 CNZBJ 04LENGTH,NOMINAL,CHUTE CHUTE NOMINAL LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE CHUTE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CNZCD 08LOCATION,DERRICK DERRICK LOCATION INDICATES THE LOCATION OF THE DERRICK. SELECT REPLY CODE 10AJ91 CNZDD 11METHOD,OPERATION,TAILGATE TAILGATE OPERATION METHOD THE MEANS BY WHICH THE TAILGATE IS OPERATED. SELECT REPLY CODE 10AC58 CNZFJ 10TEMP RATING,INSIDE,MAINTAINED MAINTAINED INSIDE TEMP RATING THE RATED INSIDE TEMPERATURE THAT IS MAINTAINED. 1D AND 1B MODE REPLY11AB36 CNZGJ 10TEMP AT WHICH INSIDE TEMP IS MAINTAINED,OUTSIDE OUTSIDE TEMP AT WHICH INSIDE TEMP IS MAINTAINED THE OUTSIDE TEMPERATURE AT WHICH THE INSIDE TEMPERATURE IS MAINTAINED. 1D AND 1B MODE REPLY11AB36 CNZHD 18TYPE,TURRET TURRET TYPE INDICATES THE TYPE OF TURRET PROVIDED. SELECT REPLY CODE 10AK54 CNZJD /D/ 18TYPE,A-FRAME A-FRAME TYPE INDICATES THE TYPE OF A-FRAME PROVIDED. SELECT REPLY CODE 10AK54 CNZKD 19CONSTRUCTION,DOOR DOOR CONSTRUCTION AN INDICATION OF THE CONSTRUCTION OF THE DOOR. SELECT REPLY CODE 10AL59 CNZLD 18TYPE,DOOR,PASSENGER PASSENGER DOOR TYPE INDICATES THE TYPE OF PASSENGER DOOR PROVIDED. SELECT REPLY CODE 10AD27 CNZMD 11METHOD,OPERATION,PASSENGER DOOR PASSENGER DOOR OPERATION METHOD THE MEANS BY WHICH THE PASSENGER DOOR IS OPERATED. SELECT REPLY CODE 10AC58 CNZNA 12QUANTITY,DOOR,EMERGENCY EMERGENCY DOOR QUANTITY THE NUMBER OF EMERGENCY DOORS PROVIDED. 1A MODE REPLY 0 CNZPJ 04LENGTH,NOMINAL,CARGO AREA CARGO AREA NOMINAL LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE CARGO AREA. 1D AND 1B MODE REPLY11AA05 CNZQJ 04WIDTH,NOMINAL,CARGO AREA CARGO AREA NOMINAL WIDTH A NOMINAL MEASUREMENT OF THE CARGO AREA TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE AREA. 1D AND 1B MODE REPLY11AA05 CNZRJ 04HEIGHT,NOMINAL,CARGO AREA CARGO AREA NOMINAL HEIGHT A NOMINAL MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE CARGO AREA. 1D AND 1B MODE REPLY11AA05 CNZSD 08LOCATION,DOOR,CARGO CARGO DOOR LOCATION INDICATES THE LOCATION OF THE CARGO DOOR/S/ ON THE ITEM. SELECT REPLY CODE 10AJ91 CNZTD 07REMOVABILITY,SIDE SIDE REMOVABILITY AN INDICATION OF WHETHER OR NOT THE SIDE(S) IS REMOVABLE. SELECT REPLY CODE 10AC29 CNZWA 12QUANTITY,PARTITION,BODY BODY PARTITION QUANTITY THE NUMBER OF BODY PARTITIONS PROVIDED. 1A MODE REPLY 0 CNZXD 08LOCATION,ENTRANCE,CENTER AISLE CENTER AISLE ENTRANCE LOCATION INDICATES THE LOCATION OF THE ENTRANCE TO THE CENTER AISLE. SELECT REPLY CODE 10AJ91 CNZYD 18TYPE,DEVICE,LOADING,POWER OPERATED POWER OPERATED LOADING DEVICE TYPE INDICATES THE TYPE OF POWER OPERATED LOADING DEVICE PROVIDED. SELECT REPLY CODE 10AK95 CNZZA 12QUANTITY,COMPARTMENT,TANK TANK COMPARTMENT QUANTITY THE NUMBER OF COMPARTMENTS IN A TANK. 1A MODE REPLY 0 CPBBD 11METHOD,HEATING,TANK TANK HEATING METHOD THE MEANS BY WHICH THE TANK IS HEATED. SELECT REPLY CODE 10AM63 CPBCD 18TYPE,LINING,TANK TANK LINING TYPE INDICATES THE TYPE OF LINING USED FOR THE TANK. SELECT REPLY CODE 10AK54 CPBDA /D/ 12QUANTITY ACCOMMODATED,TORPEDO TORPEDO QUANTITY ACCOMMODATED THE NUMBER OF TORPEDOES THE ITEM WILL ACCOMMODATE. 1A MODE REPLY 0 CPBFJ 04DISTANCE,NOMINAL,FIFTH WHEEL CENTER TO CAB FIFTH WHEEL CENTER TO CAB NOMINAL DISTANCE THE NOMINAL DISTANCE FROM THE BACK OF THE CAB TO THE FIFTH WHEEL CENTER. 1D AND 1B MODE REPLY11AA05 CPBGD 02DESIGN,CONTROL,OPERATOR OPERATOR CONTROL DESIGN THE DESIGN OF THE CONTROLS FOR THE OPERATOR. SELECT REPLY CODE 10AK54 CPBHD 07REMOVABILITY,SEAT SEAT REMOVABILITY AN INDICATION OF WHETHER OR NOT THE SEAT IS REMOVABLE. SELECT REPLY CODE 10AC29 CPBJD /D/ 07SEAT,AUXILIARY AUXILIARY SEAT AN INDICATION OF WHETHER OR NOT AN AUXILIARY SEAT IS INCLUDED. SELECT REPLY CODE 10AA49 CPBKJ 04LENGTH,OUTSIDE,NOMINAL,MAINTENANCE BODY MAINTENANCE BODY NOMINAL OUTSIDE LENGTH A MEASUREMENT OF THE LONGEST NOMINAL OUTSIDE DIMENSION OF THE MAINTENANCE BODY. 1D AND 1B MODE REPLY11AA05 CPBLJ 04WIDTH,OUTSIDE,NOMINAL,MAINTENANCE BODY MAINTENANCE BODY NOMINAL OUTSIDE WIDTH A NOMINAL OUTSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MAINTENANCE BODY OF THE ITEM. 1D AND 1B MODE REPLY11AA05 CPBMJ 04HEIGHT,OUTSIDE,NOMINAL,MAINTENANCE BODY MAINTENANCE BODY NOMINAL OUTSIDE HEIGHT A NOMINAL OUTSIDE MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE MAINTENANCE BODY. 1D AND 1B MODE REPLY11AA05 CPBNB /D/ 04SPACING IN DEG,CENTER TO CENTER,PLATE COUPLING FACILITY PLATE COUPLING FACILITY CENTER TO CENTER SPACING IN DEG THE CENTER TO CENTER SPACING OF THE FACILITIES ON THE PLATE COUPLING,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CPBPJ 04DIAMETER,OUTSIDE,RATCHET RATCHET OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A RATCHET,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPBQJ 04DIAMETER,INSIDE,RATCHET RATCHET INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A RATCHET,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPBRD /D/ 07DEVICE,TABLE-LOCKING,BASE BASE TABLE-LOCKING DEVICE AN INDICATION OF WHETHER OR NOT A BASE TABLE-LOCKING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 CPBSD /D/ 14SHAPE,TOP,TABLE TABLE TOP SHAPE THE PHYSICAL CONFIGURATION OF THE TABLE TOP. SELECT REPLY CODE 10AD07 CPBTD 02DESIGN,HANDPIECE HANDPIECE DESIGN THE DESIGN OF THE HANDPIECE PROVIDED. SELECT REPLY CODE 10AK54 CPBWD /D/ 07FEATURE,ATTACHED,WRIST JOINT WRIST JOINT ATTACHED FEATURE AN INDICATION OF WHETHER OR NOT A WRIST JOINT ATTACHED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CPBXD 14SHAPE,NOSE NOSE SHAPE THE PHYSICAL CONFIGURATION OF THE NOSE OF THE ITEM. SELECT REPLY CODE 10AD07 CPBYD /D/ 07DEVICE,LOCKING,HEXAGONAL SLEEVE HEXAGONAL SLEEVE LOCKING DEVICE AN INDICATION OF WHETHER OR NOT A HEXAGONAL SLEEVE LOCKING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 CPBZD /D/ 09MATERIAL,HANDPIECE HANDPIECE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HANDPIECE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CPCBD /D/ 17SURFACE TREATMENT,HANDPIECE HANDPIECE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A HANDPIECE SURFACE. SELECT REPLY CODE 10AD09 CPCCD /D/ 08LOCATION,JOINT,WALL,INNER/OUTER INNER/OUTER WALL JOINT LOCATION INDICATES THE LOCATION AT WHICH THE INNER AND/OR OUTER WALLS ARE JOINED. SELECT REPLY CODE 10AJ91 CPCDJ /D/ 04DISTANCE BETWEEN WALLS DISTANCE BETWEEN WALLS THE DISTANCE BETWEEN THE WALLS ON THE ITEM. MRC DISCONTINUED WITHOUT REPLACEMENT ON 01/19/2024. 2D AND 1B MODE REPLY21AA051AC20 CPCFJ 04HEIGHT,WALL WALL HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A WALL,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CPCGJ 04LENGTH,FRONT TO BACK FRONT TO BACK LENGTH A MEASUREMENT OF THE LONGEST DIMENSION FROM THE FRONT TO THE BACK OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CPCHD 19DENTURE FOR WHICH DESIGNED DENTURE FOR WHICH DESIGNED AN INDICATION OF THE DENTURE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 CPCJD 19JAW FOR WHICH DESIGNED JAW FOR WHICH DESIGNED AN INDICATION OF THE JAW FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 CPCKD /D/ 07FEATURE,USAGE,HYDROCOLLOID HYDROCOLLOID USAGE FEATURE AN INDICATION OF WHETHER OR NOT A HYDROCOLLOID USAGE FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CPCLJ 04LENGTH,INSIDE,UPPER SECTION UPPER SECTION INSIDE LENGTH A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF THE UPPER SECTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPCMJ 04WIDTH,INSIDE,UPPER SECTION UPPER SECTION INSIDE WIDTH THE INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE UPPER SECTION,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CPCNJ 04HEIGHT,SECTION,UPPER UPPER SECTION HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE UPPER SECTION,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CPCPD 18TYPE,BOTTOM,LOWER SECTION LOWER SECTION BOTTOM TYPE THE TYPE OF LOWER SECTION BOTTOM ON THE ITEM. SELECT REPLY CODE 10AK54 CPCQJ /D/ 04LENGTH,RACE,OUTER OUTER RACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE OUTER RACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPCRJ /D/ 04LENGTH,RACE,INNER INNER RACE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE INNER RACE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPCSG /D/ 19CHARACTERISTICS,MODIFICATION MODIFICATION CHARACTERISTICS AN INDICATION OF THE CHANGES OR ALTERATIONS MADE TO THE ITEM. FULL TEXT WRITE-IN 0 CPCTD /D/ 07TOLERANCES,BEARING,AFBMA JOURNAL AFBMA JOURNAL BEARING TOLERANCES AN INDICATION OF WHETHER OR NOT JOURNAL BEARING TOLERANCES ACCORDING TO ANTI-FRICTION BEARING MANUFACTURERS ASSOCIATION ARE PROVIDED. SELECT REPLY CODE 10AB22 CPCWJ 04DIAMETER,BORE,HOUSING HOUSING BORE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR HOUSING BORE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPCXA 12QUANTITY,HOLDER,COMPONENT COMPONENT HOLDER QUANTITY THE NUMBER OF COMPONENT HOLDERS PROVIDED. 1A MODE REPLY 0 CPCYG 03DESIGNATION,CHARACTER CHARACTER DESIGNATION A DESIGNATION INDICATING THE CHARACTERS PROVIDED. FULL TEXT WRITE-IN 0 CPCZD /D/ 09MATERIAL,CHARACTER CHARACTER MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CHARACTER(S) IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CPDBJ 04THICKNESS,HOLDER HOLDER THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE HOLDER,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPDCJ 04THICKNESS,CHARACTER CHARACTER THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE CHARACTER,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 CPDDJ 04LENGTH,STRIP,MOUNTING MOUNTING STRIP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING STRIP,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPDFJ 04WIDTH,STRIP,MOUNTING MOUNTING STRIP WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING STRIP,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CPDGJ 04THICKNESS,STRIP,MOUNTING MOUNTING STRIP THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE MOUNTING STRIP,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPDHD /D/ 09MATERIAL,MARKING,HOLDER HOLDER MARKING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HOLDER MARKING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CPDJD /D/ 07FEATURE,EJECTION EJECTION FEATURE AN INDICATION OF WHETHER OR NOT AN EJECTION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CPDKD /D/ 07TUBE,CONNECTING CONNECTING TUBE AN INDICATION OF WHETHER OR NOT A CONNECTING TUBE IS INCLUDED. SELECT REPLY CODE 10AA49 CPDLD /D/ 07HOOK,BELT BELT HOOK AN INDICATION OF WHETHER OR NOT A BELT HOOK IS INCLUDED. SELECT REPLY CODE 10AA49 CPDMD /D/ 09MATERIAL,PLATE,BASE BASE PLATE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BASE PLATE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CPDNJ 04HEIGHT,ADJUSTABLE,STOOL STOOL ADJUSTABLE HEIGHT AN ADJUSTABLE MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE STOOL,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CPDPJ 04DEPTH FOR WHICH DESIGNED,DRAWER DRAWER DEPTH FOR WHICH DESIGNED A MEASUREMENT BETWEEN SPECIFIED POINTS OF A DRAWER,IN DISTINCTION FROM HEIGHT,FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 CPDQJ 04HEIGHT FOR WHICH DESIGNED,DRAWER DRAWER HEIGHT FOR WHICH DESIGNED A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE DRAWER,IN DISTINCTION FROM DEPTH,FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 CPDRJ 04WIDTH FOR WHICH DESIGNED,DRAWER DRAWER WIDTH FOR WHICH DESIGNED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE DRAWER,IN DISTINCTION FROM THICKNESS,FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 CPDSJ 04DISTANCE,ROLL OUT ROLL OUT DISTANCE THE ROLL OUT DISTANCE OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CPDTG 19NAME,COMPONENT,UPHOLSTERED UPHOLSTERED COMPONENT NAME THE NAME OF THE UPHOLSTERED COMPONENT ASSIGNED BY THE CONTROLLING AGENCY. FULL TEXT WRITE-IN 0 CPDWD /D/ 09MATERIAL,UPHOLSTERY UPHOLSTERY MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE UPHOLSTERY IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CPDXD 01COLOR,UPHOLSTERY UPHOLSTERY COLOR THE HUE OR TINT OF THE UPHOLSTERY. SELECT REPLY CODE 10AD06 CPDYD /D/ 07COVERING,LAMINATE,PLASTIC PLASTIC LAMINATE COVERING AN INDICATION OF WHETHER OR NOT A PLASTIC LAMINATE COVERING IS INCLUDED. SELECT REPLY CODE 10AA49 CPDZA 12QUANTITY,SHELF,CABINET CABINET SHELF QUANTITY THE NUMBER OF SHELVES FURNISHED IN OR ON THE CABINET. 1A MODE REPLY 0 CPFBD /D/ 07DEVICE,LOCKING,MASTER MASTER LOCKING DEVICE AN INDICATION OF WHETHER OR NOT A MASTER LOCKING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 CPFCD /D/ 07DROP,TOWEL TOWEL DROP AN INDICATION OF WHETHER OR NOT A TOWEL DROP IS INCLUDED. SELECT REPLY CODE 10AA49 CPFDD 01COLOR,CABINET CABINET COLOR THE HUE OR TINT OF THE CABINET. SELECT REPLY CODE 10AD06 CPFFD 18TYPE,DOOR,CABINET CABINET DOOR TYPE INDICATES THE TYPE OF CABINET DOOR PROVIDED. SELECT REPLY CODE 10AD27 CPFGD /D/ 09MATERIAL,SINK SINK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE SINK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CPFHD 18TYPE,FAUCET FAUCET TYPE INDICATES THE TYPE OF FAUCET PROVIDED. SELECT REPLY CODE 10AK95 CPFJD /D/ 02DESIGN,INSTALLATION,TABLE TABLE INSTALLATION DESIGN THE TYPE OF INSTALLATION FOR WHICH THE TABLE IS DESIGNED. SELECT REPLY CODE 10AJ17 CPFKJ /D/A18TYPE AND QUANTITY,SECTION,TABLE TABLE SECTION TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF TABLE SECTIONS PROVIDED. 1D AND 1A MODE REPLY13AK54 CPFLA /D/ 12QUANTITY PER DRAWER,COMPARTMENT COMPARTMENT QUANTITY PER DRAWER THE NUMBER OF INDIVIDUAL COMPARTMENTS FORMED BY THE PARTITIONS PER DRAWER. 1A MODE REPLY 0 CPFMJ /D/ 04HEIGHT FROM FLOOR,OVERALL,TABLE TOP TABLE TOP OVERALL HEIGHT FROM FLOOR THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE FLOOR TO THE TABLE TOP. 2D AND 1B MODE REPLY21AA051AC20 CPFNJ /D/ 04DEPTH,OVERALL,TABLE TABLE OVERALL DEPTH AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS ON A TABLE,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CPFPD /D/ 07SINK,TABLE TABLE SINK AN INDICATION OF WHETHER OR NOT A TABLE SINK IS INCLUDED. SELECT REPLY CODE 10AA49 CPFQD /D/ 07VALVE,AIR,TABLE TABLE AIR VALVE AN INDICATION OF WHETHER OR NOT AN AIR VALVE IS INCLUDED IN OR ON THE TABLE. SELECT REPLY CODE 10AA49 CPFRD /D/ 07HOLE,WASTE,TABLE TABLE WASTE HOLE AN INDICATION OF WHETHER OR NOT A WASTE HOLE IS INCLUDED IN OR ON THE TABLE. SELECT REPLY CODE 10AA49 CPFSA /D/ 12QUANTITY,OUTLET,ELECTRICAL,TABLE TABLE ELECTRICAL OUTLET QUANTITY THE NUMBER OF ELECTRICAL OUTLETS IN OR ON THE TABLE. 1A MODE REPLY 0 CPFTD /D/ 19FACILITY,MOUNTING,BIN BIN MOUNTING FACILITY THE FACILITY FOR MOUNTING THE BIN. SELECT REPLY CODE 10AM39 CPFWJ /D/ 10CAPACITY RATING,BIN BIN CAPACITY RATING A MEASUREMENT OF THE RATED CAPACITY OF THE BIN. 1D AND 1B MODE REPLY12AG67 CPFXJ /D/ 04HEIGHT,OVERALL,BIN BIN OVERALL HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE BIN. 2D AND 1B MODE REPLY21AA051AC20 CPFYD /D/ 17SURFACE TREATMENT,LEG LEG SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE LEG SURFACE. SELECT REPLY CODE 10AD09 CPFZD /D/ 07STRAP,SECURING,LEG LEG SECURING STRAP AN INDICATION OF WHETHER OR NOT A LEG SECURING STRAP(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CPGBD /D/ 07FEATURE,TIPPED,LEG FOOT LEG FOOT TIPPED FEATURE AN INDICATION OF WHETHER OR NOT A LEG FOOT TIPPED FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CPGCA /D/ 12QUANTITY,SECTION,CENTER POST CENTER POST SECTION QUANTITY THE NUMBER OF CENTER POST SECTIONS PROVIDED. 1A MODE REPLY 0 CPGDD /D/ 07PROVISION,LOCKING,VERTICAL,HEAD HEAD VERTICAL LOCKING PROVISION AN INDICATION OF WHETHER OR NOT A HEAD VERTICAL LOCKING PROVISION IS INCLUDED. SELECT REPLY CODE 10AA49 CPGFD 02DESIGN,ELEMENT,HEATING HEATING ELEMENT DESIGN THE DESIGN OF THE HEATING ELEMENT. SELECT REPLY CODE 10AK54 CPGGA 12QUANTITY,POSITION,HEATING ELEMENT SWITCH HEATING ELEMENT SWITCH POSITION QUANTITY THE NUMBER OF HEATING ELEMENT SWITCH POSITIONS PROVIDED. 1A MODE REPLY 0 CPGHG /D/ 19GRADUATION,NUMBERED,THERMOMETER THERMOMETER NUMBERED GRADUATION AN INDICATION OF THE GRADUATIONS THAT ARE NUMBERED ON THE THERMOMETER. FULL TEXT WRITE-IN 0 CPGJD /D/ 17SURFACE TREATMENT,BASIN BASIN SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE BASIN. SELECT REPLY CODE 10AD09 CPGKD /D/ 01COLOR,BASIN BASIN COLOR THE HUE OR TINT OF THE BASIN. SELECT REPLY CODE 10AD06 CPGLJ 04DEPTH,OVERALL,BASIN BASIN OVERALL DEPTH AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS ON A BASIN,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CPGMJ 04LENGTH,OVERALL,BASIN BASIN OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BASIN. 2D AND 1B MODE REPLY21AA051AC20 CPGND 11METHOD,MOUNTING,TUBE STAND TUBE STAND MOUNTING METHOD THE MEANS USED IN MOUNTING THE TUBE STAND. SELECT REPLY CODE 10AM39 CPGPG 04SIZE ACCOMMODATED,CASSETTE,COMPARTMENT MAXIMUM COMPARTMENT MAXIMUM CASSETTE SIZE ACCOMMODATED THE MAXIMUM SIZE OF THE CASSETTE THAT THE COMPARTMENT IS DESIGNED TO ACCOMMODATE. FULL TEXT WRITE-IN 0 CPGQA 12QUANTITY,CASSETTE,COMPARTMENT MAXIMUM COMPARTMENT MAXIMUM CASSETTE QUANTITY THE MAXIMUM NUMBER OF CASSETTES THAT THE COMPARTMENT WILL ACCOMMODATE. 1A MODE REPLY 0 CPGRA 12QUANTITY,DOOR,COMPARTMENT COMPARTMENT DOOR QUANTITY THE NUMBER OF DOORS PROVIDED FOR EACH COMPARTMENT. 1A MODE REPLY 0 CPGSG /D/ 10CAPACITY,DRAWER,FILM STORAGE FILM STORAGE DRAWER CAPACITY THE RATED CAPACITY BY FILM SIZE,FILM PACKAGE QUANTITY,AND FILM QUANTITY PER PACKAGE OF THE FILM STORAGE DRAWER. FULL TEXT WRITE-IN 0 CPGTJ 04LENGTH,TRAVEL,CASSETTE MINIMUM CASSETTE MINIMUM TRAVEL LENGTH THE MINIMUM TRAVEL LENGTH OF THE CASSETTE. 1D AND 1B MODE REPLY11AA05 CPGWD /D/ 07HANDLE,CARRYING,SPRING LOADED SPRING LOADED CARRYING HANDLE AN INDICATION OF WHETHER OR NOT A SPRING LOADED CARRYING HANDLE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CPGXD /D/ 07SHELL,SHIPPING,REUSABLE REUSABLE SHIPPING SHELL AN INDICATION OF WHETHER OR NOT A REUSABLE SHIPPING SHELL IS INCLUDED. SELECT REPLY CODE 10AA49 CPGYD /D/ 07REST,CHIN CHIN REST AN INDICATION OF WHETHER OR NOT A CHIN REST IS PROVIDED. SELECT REPLY CODE 10AB22 CPGZD /D/ 07INDICATOR,HEIGHT HEIGHT INDICATOR AN INDICATION OF WHETHER OR NOT A HEIGHT INDICATOR IS PROVIDED. SELECT REPLY CODE 10AB22 CPHBD /D/ 19REGION,PEAK,SPECTRAL COLOR RESPONSE SPECTRAL COLOR RESPONSE PEAK REGION THE MAXIMUM WAVELENGTH OF LIGHT TO WHICH THE ITEM WILL RESPOND,EXPRESSED IN A COLOR OR A RANGE OF COLORS. SELECT REPLY CODE 10AD06 CPHCJ 10TEMP,WATER,DELIVERED WATER TEMP DELIVERED THE TEMPERATURE OF THE WATER DELIVERED BY THE ITEM. 1D AND 1B MODE REPLY11AB36 CPHDD 11METHOD TO PERSON,SECURING SECURING METHOD TO PERSON THE MEANS OF SECURING THE ITEM TO A PERSON. SELECT REPLY CODE 10AM39 CPHFD /D/ 19RELATIONSHIP,SUSPENSORY/URINAL SUSPENSORY/URINAL RELATIONSHIP THE RELATIONSHIP BETWEEN THE SUSPENSORY AND THE URINAL. SELECT REPLY CODE 10AL52 CPHGD 04SIZE,SUSPENSORY SUSPENSORY SIZE DESIGNATES THE SIZE OF THE SUSPENSORY. SELECT REPLY CODE 10AF81 CPHHD 18TYPE,OUTLET,TOP TOP OUTLET TYPE INDICATES THE TYPE OF TOP OUTLET PROVIDED. SELECT REPLY CODE 10AB76 CPHJJ 10CAPACITY,BOTTOM BOTTOM CAPACITY A MEASUREMENT OF THE CAPACITY OF THE BOTTOM. 1D AND 1B MODE REPLY12AG67 CPHKD 18TYPE,OUTLET,BOTTOM BOTTOM OUTLET TYPE INDICATES THE TYPE OF BOTTOM OUTLET PROVIDED. SELECT REPLY CODE 10AB76 CPHLD 11METHOD TO PERSON,SECURING,BOTTOM BOTTOM SECURING METHOD TO PERSON THE MEANS OF SECURING THE BOTTOM OF THE ITEM TO A PERSON. SELECT REPLY CODE 10AM39 CPHMD 02DESIGN,END,FORWARD FORWARD END DESIGN THE DESIGN OF THE FORWARD END. SELECT REPLY CODE 10AK54 CPHND 18TYPE,MANOMETER MANOMETER TYPE INDICATES THE TYPE OF MANOMETER PROVIDED. SELECT REPLY CODE 10AJ77 CPHPD /D/ 09MATERIAL,BRACKET BRACKET MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BRACKET IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CPHQJ 10CALIBRATION,MAXIMUM,SCALE SCALE MAXIMUM CALIBRATION THE NUMERIC VALUE OF THE MAXIMUM CALIBRATION OF A SCALE. 1D AND 1B MODE REPLY13AJ40 CPHRD 14SHAPE,CROSS-SECTIONAL,STEM STEM CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE STEM WHEN VIEWED IN CROSS SECTION. SELECT REPLY CODE 10AD07 CPHSD 19MARKING,TEMP,NORMAL NORMAL TEMP MARKING AN INDICATION OF THE MARKING(S) FOR NORMAL TEMPERATURE. SELECT REPLY CODE 10AJ65 CPHTJ 04DIAMETER FROM WRENCHING FEATURE,SIXTH SIXTH DIAMETER FROM WRENCHING FEATURE NONE. 2D AND 1B MODE REPLY21AA051AC20 CPHWJ 04LENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO END OF SIXTH DIAMETER LENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO END OF SIXTH DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CPHXJ 04DIAMETER,END,FORWARD FORWARD END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FORWARD END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPHYA /D/ 13THREAD QUANTITY PER INCH,END END THREAD QUANTITY PER INCH THE NUMBER OF THREADS ON THE END PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CPHZD /D/ 13THREAD CLASS,END END THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL END THREAD. SELECT REPLY CODE 10AN53 CPJBJ /D/ 13THREAD SIZE,PIPE,NOMINAL,END END NOMINAL PIPE THREAD SIZE THE INDUSTRIAL SIZE DESIGNATION USED TO INDICATE THE DIAMETER OF THE END PIPE THREAD. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1D AND 1B MODE REPLY11AA05 CPJCJ /D/ 13THREAD DIAMETER,END,WRENCHING FEATURE WRENCHING FEATURE END THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPJDA /D/ 13THREAD QUANTITY PER INCH,END,WRENCHING FEATURE WRENCHING FEATURE END THREAD QUANTITY PER INCH THE NUMBER OF THREADS ON THE WRENCHING FEATURE PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CPJFD /D/ 07KEYWAY,END,FORWARD FORWARD END KEYWAY AN INDICATION OF WHETHER OR NOT A FORWARD END KEYWAY IS PROVIDED. SELECT REPLY CODE 10AB22 CPJGD /D/ 07KEYWAY,END,AFTER AFTER END KEYWAY AN INDICATION OF WHETHER OR NOT AN AFTER END KEYWAY IS PROVIDED. SELECT REPLY CODE 10AB22 CPJHD 02DESIGN,COUPLING,FORWARD END FORWARD END COUPLING DESIGN THE DESIGN OF THE FORWARD END COUPLING. SELECT REPLY CODE 10AK54 CPJJD 18TYPE,COUPLING,FORWARD END FORWARD END COUPLING TYPE INDICATES THE TYPE OF FORWARD END COUPLING PROVIDED. SELECT REPLY CODE 10AH98 CPJKJ 04DIAMETER,OUTSIDE,COUPLING,FORWARD END FORWARD END COUPLING OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FORWARD END COUPLING,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPJLJ 04LENGTH,COUPLING,FORWARD END FORWARD END COUPLING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FORWARD END COUPLING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPJMJ 04THICKNESS,COUPLING,FORWARD END FORWARD END COUPLING THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE FORWARD END COUPLING,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPJND 18TYPE,HOIST,BODY BODY HOIST TYPE INDICATES THE TYPE OF BODY HOIST PROVIDED. SELECT REPLY CODE 10AK54 CPJPD 18TYPE,INCLOSURE,ENGINE ENGINE INCLOSURE TYPE INDICATES THE TYPE OF ENGINE INCLOSURE PROVIDED. SELECT REPLY CODE 10AJ95 CPJQD /D/ 08LOCATION WITHIN BODY,MOUNTING,ENGINE ENGINE MOUNTING LOCATION WITHIN BODY INDICATES THE LOCATION OF MOUNTING FOR THE ENGINE WITHIN THE BODY. SELECT REPLY CODE 10AJ91 CPJRA 10VOLTAGE,OUTLET,ELECTRICAL,INTERIOR INTERIOR ELECTRICAL OUTLET VOLTAGE THE VOLTAGE OF THE INTERIOR ELECTRICAL OUTLET/S/. 1A MODE REPLY 0 CPJSJ 10CAPACITY,CARRYING,RATED CUBIC RATED CUBIC CARRYING CAPACITY A MEASUREMENT OF THE CARRYING CAPACITY OF THE ITEM RENDERED IN CUBIC UNITS. 1D AND 1B MODE REPLY12AG67 CPJTG /D/ 19CODE AND MODEL NUMBER,MANUFACTURER,HOIST HOIST MANUFACTURER CODE AND MODEL NUMBER THE FIVE-POSITION CODE WHICH REPRESENTS THE MANUFACTURER OF THE HOIST FURNISHED WITH THE ITEM AND THE MODEL NUMBER. PLEASE USE MRC AMWN AND AZYA IN PLACE OF THIS CANCELED MRC WITH USE OF ISAC. FULL TEXT WRITE-IN 0 CPJWG /D/ 19CODE AND MODEL NUMBER,MANUFACTURER,BODY BODY MANUFACTURER CODE AND MODEL NUMBER THE FIVE-POSITION CODE WHICH REPRESENTS THE MANUFACTURER OF THE BODY FURNISHED WITH THE ITEM AND THE MODEL NUMBER. PLEASE USE MRC AMWN AND AZYA IN PLACE OF THIS CANCELED MRC WITH USE OF ISAC. FULL TEXT WRITE-IN 0 CPJXG /D/ 19CODE AND MODEL NUMBER,MANUFACTURER,CHASSIS CHASSIS MANUFACTURER CODE AND MODEL NUMBER THE FIVE-POSITION CODE WHICH REPRESENTS THE MANUFACTURER OF THE CHASSIS AND THE MODEL NUMBER. PLEASE USE MRC AMWN AND AZYA WITH USE OF ISAC IN PLACE OF THIS CANCELED MRC. FULL TEXT WRITE-IN 0 CPJYJ 04LENGTH,AREA,ADHESIVE ADHESIVE AREA LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ADHESIVE AREA,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPJZJ 04WIDTH,AREA,ADHESIVE ADHESIVE AREA WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ADHESIVE AREA,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CPKBJ 04DIAMETER,OPENING,CENTER,ADHESIVE AREA ADHESIVE AREA CENTER OPENING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CENTER OPENING OF THE ADHESIVE AREA,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPKCJ 10WEIGHT,CURB,VEHICLE VEHICLE CURB WEIGHT THE WEIGHT OF A FULLY EQUIPPED VEHICLE IN OPERATING CONDITION WITH A FULL COMPLEMENT OF FUEL,LUBRICANTS,AND COOLANT,BUT WITHOUT CREW OR PAYLOAD. 1D AND 1B MODE REPLY12AG67 CPKDJ 10WEIGHT,GROSS,MAXIMUM,VEHICLE VEHICLE MAXIMUM GROSS WEIGHT THE MAXIMUM WEIGHT OF A FULLY EQUIPPED VEHICLE AND ALLOWABLE PAYLOAD OF CARGO OR PASSENGERS. 1D AND 1B MODE REPLY12AG67 CPKFD /D/ 07FEATURE,AURAL AURAL FEATURE AN INDICATION OF WHETHER OR NOT AN AURAL FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CPKGJ 04DIAMETER,OPENING,FILLER FILLER OPENING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FILLER OPENING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPKHJ /D/ 04WIDTH,OPENING,FILLER FILLER OPENING WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FILLER OPENING,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CPKJD /D/ 07FEATURE,ATTACHMENT,SCREW CAP SCREW CAP ATTACHMENT FEATURE AN INDICATION OF WHETHER OR NOT A SCREW CAP ATTACHMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CPKKA /D/ 12QUANTITY,SLIT,HANDLE HANDLE SLIT QUANTITY THE NUMBER OF HANDLE SLITS IN THE ITEM. 1A MODE REPLY 0 CPKLD /D/ 07FEATURE,IMPERVIOUS IMPERVIOUS FEATURE AN INDICATION OF WHETHER OR NOT AN IMPERVIOUS FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CPKMD /D/ 09MATERIAL,CASE,INNER INNER CASE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INNER CASE IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CPKND 01COLOR,CASE,INNER INNER CASE COLOR THE HUE OR TINT OF THE INNER CASE. SELECT REPLY CODE 10AD06 CPKPD /D/ 07MIXTURE,HEATING,INNER CASE INNER CASE HEATING MIXTURE AN INDICATION OF WHETHER OR NOT AN INNER CASE HEATING MIXTURE IS INCLUDED. SELECT REPLY CODE 10AA49 CPKQD /D/ 07INSTRUCTIONS,PRINTED,INNER CASE INNER CASE PRINTED INSTRUCTIONS AN INDICATION OF WHETHER OR NOT INNER CASE PRINTED INSTRUCTIONS ARE INCLUDED. SELECT REPLY CODE 10AA49 CPKRD 01COLOR,CASE,OUTER OUTER CASE COLOR THE HUE OR TINT OF THE OUTER CASE. SELECT REPLY CODE 10AD06 CPKSD /D/ 08LOCATION,MATERIAL,OUTER CASE COATING OUTER CASE COATING MATERIAL LOCATION THE LOCATION OF THE OUTER CASE TO WHICH A COATING MATERIAL HAS BEEN APPLIED. SELECT REPLY CODE 10AJ91 CPKTJ 04LENGTH,CASE,OUTER OUTER CASE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE OUTER CASE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPKWJ 04WIDTH,CASE,OUTER OUTER CASE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE OUTER CASE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CPKXD /D/ 08LOCATION,FLAP,OUTER CASE OUTER CASE FLAP LOCATION INDICATES THE LOCATION OF THE FLAP ON THE OUTER CASE. SELECT REPLY CODE 10AJ91 CPKYD /D/ 07TAPE,ENCIRCLING,CASE,OUTER OUTER CASE ENCIRCLING TAPE AN INDICATION OF WHETHER OR NOT AN OUTER CASE ENCIRCLING TAPE IS INCLUDED. SELECT REPLY CODE 10AA49 CPKZG /D/ 19MARKING,CASE,OUTER OUTER CASE MARKING AN INDICATION OF THE MARKING(S) ON THE OUTER CASE. FULL TEXT WRITE-IN 0 CPLBA /D/ 12QUANTITY,COMPARTMENT,AIR AIR COMPARTMENT QUANTITY THE NUMBER OF AIR COMPARTMENTS PROVIDED. 1A MODE REPLY 0 CPLCA /D/ 12QUANTITY,VALVE,INFLATION INFLATION VALVE QUANTITY THE NUMBER OF INFLATION VALVES PROVIDED. 1A MODE REPLY 0 CPLDJ /D/ 04DIAMETER,OVERALL,ASSEMBLY ASSEMBLY OVERALL DIAMETER A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF AN ASSEMBLY. 2D AND 1B MODE REPLY21AA051AC20 CPLFJ A18TYPE AND QUANTITY,ENTRANCE ENTRANCE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF ENTRANCES PROVIDED. 1D AND 1A MODE REPLY13AK60 CPLGA 12QUANTITY,DOOR,CAB CAB DOOR QUANTITY THE NUMBER OF DOORS PROVIDED ON THE CAB. 1A MODE REPLY 0 CPLHD /D/ 11METHOD,LUBRICATION LUBRICATION METHOD THE MEANS BY WHICH THE ITEM IS LUBRICATED. PLEASE USE MRC AEAH IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AC75 CPLJD /D/ 08LOCATION,COUNTERBORE COUNTERBORE LOCATION INDICATES THE PRESENCE OR ABSENCE OF A COUNTERBORE PROVIDED IN THE BORE OF AN ITEM. SELECT REPLY CODE 10AJ91 CPLKJ /D/ 10PITCH IN INCHES PITCH IN INCHES THE DISTANCE BETWEEN IDENTICAL,EQUALLY SPACED SURFACES OF TWO ADJOINING TEETH OR THREADS ON A GEAR,RACK,OR WORM,MEASURED ALONG THE PITCH CIRCLE OR PITCH LINE. 1D AND 1B MODE REPLY12AL87 CPLLD /D/ 19CLASSIFICATION,PRECISION PRECISION CLASSIFICATION THE QUALITY DESIGNATION OF A GEAR AS DETERMINED BY INDUSTRY,ASSOCIATION,OR INDIVIDUAL GEAR MANUFACTURERS STANDARDS. SELECT REPLY CODE 10AE99 CPLMJ 10CURRENT RATING PER POLE,CONTINUOUS LOAD,MAXIMUM MAXIMUM CONTINUOUS LOAD CURRENT RATING PER POLE THE MAXIMUM CURRENT LOAD THAT EACH POLE IS RATED TO CARRY CONTINUOUSLY. 2D AND 1B MODE REPLY21AC301AB62 CPLND /D/ 09MATERIAL,BLOCK,HEEL HEEL BLOCK MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE HEEL BLOCK IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CPLPD /D/ 09MATERIAL,THREAD THREAD MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE THREAD IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CPLQD /D/ 09MATERIAL,STIRRUP STIRRUP MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE STIRRUP IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CPLRD 02DESIGN,UNIT UNIT DESIGN THE DESIGN OF THE UNIT. SELECT REPLY CODE 10AK54 CPLSD 18TYPE,STANDARD STANDARD TYPE A DESIGNATION INDICATING THE STANDARD TYPE. SELECT REPLY CODE 10AM64 CPLTG 04SIZE RANGE,GAGING GAGING SIZE RANGE THE RANGE OF DIFFERENT SIZES THE ITEM WILL GAGE. FULL TEXT WRITE-IN 0 CPLWD /D/ 07MARKINGS,EQUIVALENT,DECIMAL,BACK SIDE BACK SIDE DECIMAL EQUIVALENT MARKINGS AN INDICATION OF WHETHER OR NOT DECIMAL EQUIVALENT MARKINGS ON THE BACK SIDE ARE INCLUDED. SELECT REPLY CODE 10AA49 CPLXD 08LOCATION,ZERO,SCALE SCALE ZERO LOCATION INDICATES THE LOCATION OF THE ZERO ON THE SCALE. SELECT REPLY CODE 10AJ91 CPLYG /D/ 19INGREDIENT AND PERCENTAGE,ACTIVE ACTIVE INGREDIENT AND PERCENTAGE THE NAME AND PERCENTAGE OF THE ACTIVE INGREDIENT/S/ THAT COMPOSES THE ITEM. FULL TEXT WRITE-IN 0 CPLZJ 10AMOUNT,SOLUTION SOLUTION AMOUNT THE AMOUNT OF SOLUTION PROVIDED. 1D AND 1B MODE REPLY12AG67 CPMBD /D/ 07BAIL,SUSPENSION SUSPENSION BAIL AN INDICATION OF WHETHER OR NOT A SUSPENSION BAIL IS INCLUDED. SELECT REPLY CODE 10AA49 CPMCD /D/ 07TUBE,AIR AIR TUBE AN INDICATION OF WHETHER OR NOT AN AIR TUBE IS INCLUDED. SELECT REPLY CODE 10AA49 CPMDG /D/ 11METHOD,CLOSURE CLOSURE METHOD THE MEANS PROVIDED TO CLOSE THE OPENING OF THE ITEM. PLEASE USE MRC AFPP IN PLACE OF THIS CANCELED MRC. FULL TEXT WRITE-IN 0 CPMFD /D/ 07TRANSFORMER/RECTIFIER TRANSFORMER/RECTIFIER AN INDICATION OF WHETHER OR NOT A TRANSFORMER AND/OR RECTIFIER ARE INCLUDED. SELECT REPLY CODE 10AA49 CPMGA /D/ 12QUANTITY,PIECE,CHEST CHEST PIECE QUANTITY THE NUMBER OF CHEST PIECES INCLUDED. 1A MODE REPLY 0 CPMHJ /D/ 04DIAMETER,OVERALL,BASIN BASIN OVERALL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BASIN,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPMJD /D/ 07HAND,COUNTER,DIAL TELL-TALE REVOLUTION DIAL TELL-TALE REVOLUTION COUNTER HAND AN INDICATION OF WHETHER OR NOT A DIAL TELL-TALE REVOLUTION COUNTER HAND IS INCLUDED. SELECT REPLY CODE 10AA49 CPMKD /D/ 07HAND,TELL-TALE TELL-TALE HAND AN INDICATION OF WHETHER OR NOT A TELL-TALE HAND IS INCLUDED. SELECT REPLY CODE 10AA49 CPMLG /D/ 13THREAD PITCH THREAD PITCH AN INDICATION OF THE THREAD PITCH(ES) OF THE ITEM. FULL TEXT WRITE-IN 0 CPMMG /D/ 04ANGLE IN DEG,BLADE BLADE ANGLE IN DEG THE ANGLE OF BLADE PITCH MEASURED FROM THE PLANE AT A SPECIFIED LOCATION,EXPRESSED IN DEGREES. FULL TEXT WRITE-IN 0 CPMNG /D/ 04THICKNESS,BLADE BLADE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A BLADE,IN DISTINCTION FROM LENGTH OR WIDTH. FULL TEXT WRITE-IN 0 CPMPG /D/ 04DIAMETER,WIRE WIRE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WIRE,AND TERMINATES AT THE CIRCUMFERENCE. FULL TEXT WRITE-IN 0 CPMQD /D/ 07FEATURE,IMPERVIOUS,BLOOD/OIL BLOOD/OIL IMPERVIOUS FEATURE AN INDICATION OF WHETHER OR NOT A BLOOD AND/OR OIL IMPERVIOUS FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CPMRJ /D/ 04DIAMETER,THROAT THROAT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH INTERSECTS THE AXIS OF A WORM GEAR OR WORM WHEEL AT THE RADIAL CENTERS OF THE OPPOSED CONCAVE SURFACES OF THE THROAT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPMSJ /D/ 04DIAMETER FOR WHICH DESIGNED,OUTSIDE,HOSE/TUBE HOSE/TUBE OUTSIDE DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOSE OR TUBE FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPMTD /D/ 11METHOD,ADJUSTING,WRIST WRIST ADJUSTING METHOD THE MEANS USED TO REGULATE THE FIT OF THE GARMENT AT THE WRIST. SELECT REPLY CODE 10AF69 CPMWJ 04THICKNESS,BLADE BLADE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF A BLADE,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 CPMXD /D/ 07EDGE,BLADE,BEVELED BEVELED BLADE EDGE AN INDICATION OF WHETHER OR NOT A BEVELED BLADE EDGE IS INCLUDED. SELECT REPLY CODE 10AA49 CPMYD /D/ 07MATERIAL,STEEL,STAINLESS STAINLESS STEEL MATERIAL AN INDICATION OF WHETHER OR NOT STAINLESS STEEL MATERIAL IS INCLUDED. SELECT REPLY CODE 10AA49 CPMZJ 10UNIT,MEASUREMENT,SCALE SCALE MEASUREMENT UNIT AN INDICATION OF THE UNIT OF MEASURE FOR WHICH THE SCALE IS DESIGNED. 1D AND 1B MODE REPLY12AG67 CPNBJ /D/ 04TAPER PER FOOT,END,FORWARD FORWARD END TAPER PER FOOT THE AMOUNT OF TAPER OF THE FORWARD END,EXPRESSED PER FOOT. 2D AND 1B MODE REPLY21AA051AC20 CPNCJ 04LENGTH,TAPER,FORWARD END FORWARD END TAPER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TAPERED PORTION OF THE FORWARD END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPNDA /D/ 12QUANTITY,STRIPE STRIPE QUANTITY THE NUMBER OF STRIPES PROVIDED. 1A MODE REPLY 0 CPNFD /D/ 07END,FORWARD,THREADED THREADED FORWARD END AN INDICATION OF WHETHER OR NOT A THREADED FORWARD END IS INCLUDED. SELECT REPLY CODE 10AA49 CPNGJ 04DIAMETER,MAJOR,FORWARD END FORWARD END MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST SURFACE OF THE FORWARD END,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPNHJ A13THREAD QUANTITY,END,FORWARD FORWARD END THREAD QUANTITY THE NUMBER OF THREADS ON THE FORWARD END OF THE ITEM,MEASURED ON A LINE PARALLEL TO THE THREAD AXIS. 1D AND 1A MODE REPLY13AJ40 CPNJJ 13THREAD LENGTH,END,FORWARD FORWARD END THREAD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE THREADED PORTION OF THE FORWARD END. 1D AND 1B MODE REPLY11AA05 CPNKD 02DESIGN,COUPLING,AFTER END AFTER END COUPLING DESIGN THE DESIGN OF THE AFTER END COUPLING. SELECT REPLY CODE 10AK54 CPNLD /D/ 18TYPE,COUPLING COUPLING TYPE INDICATES THE TYPE OF COUPLING PROVIDED. SELECT REPLY CODE 10AH98 CPNMJ 04LENGTH,COUPLING COUPLING LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE COUPLING,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPNND /D/ 07CUP,PARAFFIN PARAFFIN CUP AN INDICATION OF WHETHER OR NOT A PARAFFIN CUP IS INCLUDED. SELECT REPLY CODE 10AA49 CPNPJ /D/ 04LENGTH,LIFTER,COMPOUND COMPOUND LIFTER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE COMPOUND LIFTER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPNQJ /D/ 04DIAMETER,LIFTER,COMPOUND COMPOUND LIFTER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COMPOUND LIFTER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPNRJ /D/ 04WIDTH,LIFTER,COMPOUND COMPOUND LIFTER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE COMPOUND LIFTER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CPNSD /D/ 07PLATFORM,REVERSIBLE REVERSIBLE PLATFORM AN INDICATION OF WHETHER OR NOT A REVERSIBLE PLATFORM IS INCLUDED. SELECT REPLY CODE 10AA49 CPNTD /D/ 07CONDITIONER,HYROCOLLOID HYROCOLLOID CONDITIONER AN INDICATION OF WHETHER OR NOT A HYDROCOLLOID CONDITIONER IS INCLUDED. SELECT REPLY CODE 10AA49 CPNWD /D/ 07SECTION,STORAGE,SYRINGE/TUBE SYRINGE/TUBE STORAGE SECTION AN INDICATION OF WHETHER OR NOT A SYRINGE AND/OR TUBE STORAGE SECTION/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CPNYG /D/ 10TOLERANCE,RANGE,GAGING GAGING RANGE TOLERANCE THE LIMITS OF PERMISSIBLE VARIATION IN THE GAGING RANGE OF THE ITEM. FULL TEXT WRITE-IN 0 CPNZA /D/ 12QUANTITY PER SET,BLOCK BLOCK QUANTITY PER SET THE NUMBER OF BLOCKS INCLUDED IN A SET. 1A MODE REPLY 0 CPPBG /D/ 04SIZE,GAGING,INDIVIDUAL BLOCK INDIVIDUAL BLOCK GAGING SIZE THE GAGING SIZE OF EACH BLOCK WITHIN THE ITEM. FULL TEXT WRITE-IN 0 CPPCJ 04SIZE,GAGING GAGING SIZE DESIGNATES THE GAGING SIZE OF THE ITEM. 1D AND 1B MODE REPLY11AA05 CPPDJ T04SIZE TOLERANCE,GAGING GAGING SIZE TOLERANCE THE LIMITS OF PERMISSIBLE VARIATION OF THE GAGING SIZE. 1D AND 1F MODE REPLY11AA05 CPPFD /D/ 05DIRECTION,ROTATION,HEAD HEAD ROTATION DIRECTION THE DIRECTION IN WHICH THE HEAD IS DESIGNED TO ROTATE,WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AA38 CPPGD /D/ 07MARKINGS,LINE/THICKNESS,INTERVAL INTERVAL LINE/THICKNESS MARKINGS AN INDICATION OF WHETHER OR NOT INTERVAL LINES AND/OR THICKNESS MARKINGS ARE INCLUDED. SELECT REPLY CODE 10AA49 CPPHJ A18TYPE AND QUANTITY,FEELER FEELER TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF FEELERS PROVIDED. 1D AND 1A MODE REPLY13AK54 CPPJD 19CONSTRUCTION,FEELER FEELER CONSTRUCTION THE CONSTRUCTION OF THE FEELER(S). SELECT REPLY CODE 10AL59 CPPKD /D/ 07DEVICE,TENSION,LOCKING LOCKING TENSION DEVICE AN INDICATION OF WHETHER OR NOT A LOCKING TENSION DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 CPPLD /D/ 07TOOL,ADJUSTING,GAP GAP ADJUSTING TOOL AN INDICATION OF WHETHER OR NOT A GAP ADJUSTING TOOL IS INCLUDED. SELECT REPLY CODE 10AA49 CPPMD /D/ 07BASE,V-SLOTTED V-SLOTTED BASE AN INDICATION OF WHETHER OR NOT A V-SLOTTED BASE IS INCLUDED. SELECT REPLY CODE 10AA49 CPPND 18TYPE,ALIGNMENT,BASE BASE ALIGNMENT TYPE INDICATES THE TYPE OF ALIGNMENT USED ON THE BASE. SELECT REPLY CODE 10AF16 CPPPJ 04WIDTH,OVERALL,BASIN BASIN OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BASIN,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CPPQD /D/ 09MATERIAL,END,BED BED END MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE BED END IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT WITH ISAC FROM TABLE 0013 IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10AD09 CPPRD /D/ 17SURFACE TREATMENT,END,BED BED END SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE BED END SURFACE. SELECT REPLY CODE 10AD09 CPPSD /D/ 07SOCKET,ACCESSORY,BED END BED END ACCESSORY SOCKET AN INDICATION OF WHETHER OR NOT A BED END ACCESSORY/IES/ SOCKET/S/ IS INCLUDED. SELECT REPLY CODE 10AA49 CPPTD /D/ 18TYPE,CASTER,BED END BED END CASTER TYPE INDICATES THE TYPE OF BED END CASTERS INCLUDED. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AL49 CPPWD /D/ 07LEGS,ADJUSTABLE,BED END BED END ADJUSTABLE LEGS AN INDICATION OF WHETHER OR NOT ADJUSTABLE LEGS ARE INCLUDED IN THE BED END/S/. SELECT REPLY CODE 10AA49 CPPXA 12QUANTITY,SECTION,SPRING SPRING SECTION QUANTITY THE NUMBER OF SPRING SECTIONS PROVIDED. 1A MODE REPLY 0 CPPYD /D/ 18TYPE,MECHANISM,SPRING ELEVATING SPRING ELEVATING MECHANISM TYPE INDICATES THE TYPE OF SPRING ELEVATING MECHANISM PROVIDED. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AK95 CPPZD 19SECTION,ELEVATED,SPRING SPRING ELEVATED SECTION AN INDICATION OF THE SPRING SECTION THAT CAN BE ELEVATED. SELECT REPLY CODE 10AJ91 CPQBD /D/ 08LOCATION,MECHANISM,SPRING SECTION SPRING SECTION MECHANISM LOCATION INDICATES THE LOCATION OF THE SPRING SECTION MECHANISM ON THE ITEM. SELECT REPLY CODE 10AJ91 CPQCJ 04DIAMETER,WHEEL,FRONT FRONT WHEEL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FRONT WHEEL/S/,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPQDD /D/ 18TYPE,MOUNTING,FRONT WHEEL FRONT WHEEL MOUNTING TYPE INDICATES THE TYPE OF MOUNTING USED TO SUPPORT THE FRONT WHEEL/S/. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AH86 CPQFD /D/ 18TYPE,WHEEL,REAR REAR WHEEL TYPE INDICATES THE TYPE OF REAR WHEEL/S/ PROVIDED. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AK54 CPQGJ 04DIAMETER,WHEEL,REAR REAR WHEEL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE REAR WHEEL/S/,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPQHD /D/ 18TYPE,MOUNTING,REAR WHEEL REAR WHEEL MOUNTING TYPE INDICATES THE TYPE OF MOUNTING USED TO SUPPORT THE REAR WHEEL/S/. SELECT REPLY CODE 10AH86 CPQJD 01COLOR,END,BED BED END COLOR THE HUE OR TINT OF THE BED END. SELECT REPLY CODE 10AD06 CPQKD /D/ 14SHAPE,END,TUBULAR BED TUBULAR BED END SHAPE THE PHYSICAL CONFIGURATION OF THE TUBULAR BED END. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AD07 CPQLD 19SECTION,ADJUSTABLE ADJUSTABLE SECTION AN INDICATION OF THE SECTION(S) THAT IS ADJUSTABLE. SELECT REPLY CODE 10AJ91 CPQMD /D/ 07RETAINER,MATTRESS,SPRING SPRING MATTRESS RETAINER AN INDICATION OF WHETHER OR NOT A SPRING MATTRESS RETAINER IS INCLUDED. SELECT REPLY CODE 10AA49 CPQND /D/ 07FEATURE BETWEEN JAWS,MEASUREMENT MEASUREMENT FEATURE BETWEEN JAWS AN INDICATION OF WHETHER OR NOT A MEASUREMENT FEATURE BETWEEN JAWS IS INCLUDED. SELECT REPLY CODE 10AA49 CPQPJ 04WIDTH,HEEL HEEL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE HEEL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CPQQD /D/ 07HOLE,END END HOLE AN INDICATION OF WHETHER OR NOT AN END HOLE(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CPQRJ 04DIAMETER,SURFACE,CLAMPING CLAMPING SURFACE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR CLAMPING SURFACE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPQSD /D/ 09MATERIAL,PLATING PLATING MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PLATING IS FABRICATED. SELECT REPLY CODE 10AD09 CPQTD /D/ 07FINISH,PLATED PLATED FINISH AN INDICATION OF WHETHER OR NOT A PLATED FINISH IS INCLUDED. SELECT REPLY CODE 10AA49 CPQWJ 04LENGTH AT ZERO MICROMETER SETTING,PROJECTION,SPINDLE SPINDLE PROJECTION LENGTH AT ZERO MICROMETER SETTING THE LENGTH OF THE SPINDLE PROJECTION WITH THE MICROMETER SET AT ZERO. 2D AND 1B MODE REPLY21AA051AC20 CPQXD 18TYPE,SETTING,DIAL DIAL SETTING TYPE INDICATES THE TYPE OF DIAL SETTING PROVIDED. SELECT REPLY CODE 10AK54 CPQYD 08LOCATION,POINT,CONTACT CONTACT POINT LOCATION INDICATES THE LOCATION OF THE CONTACT POINT/S/. SELECT REPLY CODE 10AJ91 CPQZD 18TYPE,ACTION,CONTACT POINT CONTACT POINT ACTION TYPE INDICATES THE TYPE OF CONTACT POINT/S/ ACTION. SELECT REPLY CODE 10AK95 CPRBL 16STYLE DESIGNATOR,POINT,CONTACT CONTACT POINT STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CONTACT POINT/S/. 1L MODE REPLY 0 CPRCD /D/ 07FEATURE,MOVEMENT,CUSHIONED CUSHIONED MOVEMENT FEATURE AN INDICATION OF WHETHER OR NOT A CUSHIONED MOVEMENT FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CPRDD /D/ 07LEVER,LIFTING LIFTING LEVER AN INDICATION OF WHETHER OR NOT A LIFTING LEVER IS INCLUDED. SELECT REPLY CODE 10AA49 CPRFJ 18TYPE AND RATING PER POLE IN VOLTS,VOLTAGE,OPERATING OPERATING VOLTAGE TYPE AND RATING PER POLE IN VOLTS INDICATES THE TYPE AND VALUE OF OPERATING VOLTAGE FOR WHICH EACH POLE IS DESIGNED TO OPERATE,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AB62 CPRGJ 18TYPE AND RATING PER POLE IN AMPS,CURRENT,MAXIMUM INTERRUPTING CAPACITY MAXIMUM INTERRUPTING CAPACITY CURRENT TYPE AND RATING PER POLE IN AMPS INDICATES THE TYPE AND VALUE OF THE MAXIMUM SHORT CIRCUIT CURRENT THAT THE ITEM WILL SUCCESSFULLY INTERRUPT,PER POLE,AT THE SPECIFIED RATED VOLTAGE,EXPRESSED IN AMPERES. 1D AND 1B MODE REPLY11AB62 CPRHD 18TYPE,PROTECTION,CIRCUIT CIRCUIT PROTECTION TYPE INDICATES THE TYPE OF ELECTRICAL CONDITION THAT WILL CAUSE THE DEVICE TO TRIP. SELECT REPLY CODE 10AJ49 CPRJD 11METHOD,TRIP RELEASE TRIP RELEASE METHOD THE MEANS BY WHICH THE TRIP MECHANISM IS RELEASED. SELECT REPLY CODE 10AK66 CPRKJ 18TYPE AND RATING IN VOLTS,TRIP COIL VOLTAGE,AUXILIARY AUXILIARY TRIP COIL VOLTAGE TYPE AND RATING IN VOLTS INDICATES THE TYPE AND VOLTAGE RATING REQUIRED TO OPERATE THE AUXILIARY /REMOTELY ACTUATED/ TRIP ACTUATOR,EXPRESSED IN VOLTS. 2D AND 1B MODE REPLY21AB621AC20 CPRLD 19CHARACTERISTIC,RELEASE,TRIP TRIP RELEASE CHARACTERISTIC DENOTES THE TYPE OF TRIP RELEASE ACTION. SELECT REPLY CODE 10AH83 CPRNB 10CURRENT RATING PER POLE IN PERCENT,TRIP RATING OF CONTINUOUS,ULTIMATE ULTIMATE TRIP RATING OF CONTINUOUS CURRENT RATING PER POLE IN PERCENT THE CONTINUOUS CURRENT RATING PER POLE AT WHICH THE DEVICE MUST TRIP IN A SPECIFIED TIME,EXPRESSED IN PERCENT. 1B MODE REPLY 0 CPRPJ 10TIME PER POLE IN SECONDS,TRIP,ULTIMATE ULTIMATE TRIP TIME PER POLE IN SECONDS THE ULTIMATE TIME PER POLE IN WHICH THE DEVICE MUST TRIP,EXPRESSED IN SECONDS. 1D AND 1B MODE REPLY11AC20 CPRQD 11METHOD,RESET RESET METHOD THE MEANS PROVIDED TO REPOSITION THE MECHANISM SO THAT THE DEVICE IS READY TO FUNCTION. SELECT REPLY CODE 10AC58 CPRRD 18TYPE,MECHANISM,TRIPPING,MAIN CONTACT MAIN CONTACT TRIPPING MECHANISM TYPE INDICATES THE TYPE OF MECHANISM PROVIDED FOR TRIPPING MAIN CONTACTS. SELECT REPLY CODE 10AC82 CPRSJ /D/ 18TYPE AND RATING IN VOLTS,ACTUATOR VOLTAGE,RESET RESET ACTUATOR VOLTAGE TYPE AND RATING IN VOLTS INDICATES THE TYPE AND VOLTAGE RATING REQUIRED TO OPERATE THE RESET ACTUATOR,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AB62 CPRTJ A18TYPE AND QUANTITY,ACTUATOR,MANUAL MANUAL ACTUATOR TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF ACTUATORS PROVIDED FOR MANUAL CONTROL. 1D AND 1A MODE REPLY14AC58 CPRWD 19FUNCTION,ACTUATOR ACTUATOR FUNCTION DENOTES THE ACTION IMPARTED BY ACTUATOR OPERATION. SELECT REPLY CODE 10AE74 CPRXD 19DESIGNATION,POSITION,ACTUATOR ACTUATOR POSITION DESIGNATION AN INDICATION OF THE DESIGNATED POSITION OF THE ACTUATOR. SELECT REPLY CODE 10AJ50 CPRYD 19ARRANGEMENT,LINKAGE,EXTERNAL ACTUATOR EXTERNAL ACTUATOR LINKAGE ARRANGEMENT INDICATES THE ARRANGEMENT OF THE EXTERNALLY CONNECTED ACTUATORS. SELECT REPLY CODE 10AH86 CPRZJ A19FUNCTION AND QUANTITY,AUXILIARY SWITCH AUXILIARY SWITCH FUNCTION AND QUANTITY THE FUNCTION FOR WHICH THE AUXILIARY SWITCH IS DESIGNED AND THE NUMBER PROVIDED. 1D AND 1A MODE REPLY12AE74 CPSBJ /D/ 18TYPE AND RATING IN AMPS,CURRENT,SWITCH SWITCH CURRENT TYPE AND RATING IN AMPS INDICATES THE TYPE AND AMOUNT OF ELECTRICAL FLOW WHICH THE SWITCH IS DESIGNATED TO OPERATE,EXPRESSED IN AMPERES. 1D AND 1B MODE REPLY11AB62 CPSCJ /D/ 18TYPE AND RATING IN VOLTS,VOLTAGE,SWITCH SWITCH VOLTAGE TYPE AND RATING IN VOLTS INDICATES THE TYPE AND AMOUNT OF VOLTAGE AT WHICH THE SWITCH IS RATED FOR NORMAL OPERATION,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY11AB62 CPSDD /D/ 18TYPE,TERMINAL,SWITCH SWITCH TERMINAL TYPE INDICATES THE TYPE OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE SWITCH. SELECT REPLY CODE 10AA58 CPSFJ T10CURRENT RANGE PER POLE IN AMPS,TRIP SETTING,ADJUSTABLE ADJUSTABLE TRIP SETTING CURRENT RANGE PER POLE IN AMPS THE MINIMUM AND MAXIMUM VALUES OF CURRENT TO WHICH AN ADJUSTABLE TRIP SETTING DEVICE MAY BE SET PER POLE,EXPRESSED IN AMPERES. 1D AND 1F MODE REPLY11AB62 CPSMD 19CONFIGURATION,TRIP RELEASE,INTERNAL INTERNAL TRIP RELEASE CONFIGURATION THE BASIC INTERNAL ELECTRICAL CONFIGURATION OF THE TRIP MECHANISM. SELECT REPLY CODE 10AE97 CPSND 19POSITION,ADJUSTMENT,SPECIAL,SPRING SPRING SPECIAL ADJUSTMENT POSITION THE SPECIAL POSITION(S) TO WHICH THE SPRING CAN BE ADJUSTED. SELECT REPLY CODE 10AF63 CPSPJ 04HEIGHT ABOVE FLOOR,TOP,SPRING SPRING TOP HEIGHT ABOVE FLOOR A MEASUREMENT FROM THE FLOOR SURFACE TO THE TOP OF THE SPRING. 2D AND 1B MODE REPLY21AA051AC20 CPSQJ 04LENGTH,SEAT SEAT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SEAT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPSRD /D/ 07FEATURE,NONALLERGENIC/NONTOXIC NONALLERGENIC/NONTOXIC FEATURE AN INDICATION OF WHETHER OR NOT A NONALLERGENIC AND/OR NONTOXIC FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CPSSD 11METHOD,SECURING TO MATTRESS SECURING TO MATTRESS METHOD THE MEANS OF SECURING THE ITEM TO THE MATTRESS. SELECT REPLY CODE 10AM39 CPSTD /D/ 07LEG,FOLDING FOLDING LEG AN INDICATION OF WHETHER OR NOT A FOLDING LEG(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CPSWD /D/ 07RAIL,GUARD,TABLE TOP TABLE TOP GUARD RAIL AN INDICATION OF WHETHER OR NOT A TABLE TOP GUARD RAIL IS INCLUDED. SELECT REPLY CODE 10AA49 CPSXD /D/ 07COATING BOTH SIDES,ADHESIVE ADHESIVE COATING BOTH SIDES AN INDICATION OF WHETHER OR NOT AN ADHESIVE COATING ON BOTH SIDES IS INCLUDED. SELECT REPLY CODE 10AA49 CPSYA 03DESIGNATION,SIZE,CORE CORE SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE CORE IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1A MODE REPLY 0 CPSZD /D/ 07DEVICE,CUTTING CUTTING DEVICE AN INDICATION OF WHETHER OR NOT A CUTTING DEVICE IS INCLUDED. SELECT REPLY CODE 10AA49 CPTBJ 04THICKNESS,COUPLING COUPLING THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE COUPLING,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPTCD 02DESIGN,END,AFTER AFTER END DESIGN THE DESIGN OF THE AFTER END. SELECT REPLY CODE 10AK54 CPTDD /D/ 07END,AFTER,THREADED THREADED AFTER END AN INDICATION OF WHETHER OR NOT A THREADED AFTER END IS INCLUDED. SELECT REPLY CODE 10AA49 CPTFJ 04DIAMETER,OUTSIDE,FORWARD BEARING SLEEVE FORWARD BEARING SLEEVE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FORWARD BEARING SLEEVE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPTGJ 04LENGTH,SLEEVE,FORWARD BEARING FORWARD BEARING SLEEVE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE FORWARD BEARING SLEEVE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPTHJ 04DIAMETER,OUTSIDE,AFTER BEARING SLEEVE AFTER BEARING SLEEVE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE AFTER BEARING SLEEVE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPTJJ 04DISTANCE BETWEEN HOLES ALONG FIRST STEM LENGTH,CENTER TO CENTER,LONGEST LONGEST CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG FIRST STEM LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CPTKJ 04DISTANCE BETWEEN HOLES ALONG SECOND STEM LENGTH,CENTER TO CENTER,SHORTEST SHORTEST CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG SECOND STEM LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CPTLJ 04DISTANCE TO FIRST HOLE ALONG FIRST STEM LENGTH,BASE STEM BASE STEM DISTANCE TO FIRST HOLE ALONG FIRST STEM LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CPTMJ 04DISTANCE TO FIRST HOLE ALONG SECOND STEM LENGTH,BASE STEM BASE STEM DISTANCE TO FIRST HOLE ALONG SECOND STEM LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CPTNJ /D/ 04DISTANCE BETWEEN HOLES ON STEM SOCKET,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN HOLES ON STEM SOCKET NONE. 2D AND 1B MODE REPLY21AA051AC20 CPTPJ 04LENGTH,SLEEVE,AFTER BEARING AFTER BEARING SLEEVE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE AFTER BEARING SLEEVE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPTQH /D/ 08LOCATION,SWITCH SWITCH LOCATION INDICATES THE LOCATION OF THE SWITCH ON THE ITEM. 2D MODE REPLY 23AJ913AJ50 CPTSG 08LOCATION,COVERING COVERING LOCATION INDICATES THE LOCATION ON AN ITEM TO WHICH A COVERING HAS BEEN APPLIED. FULL TEXT WRITE-IN 0 CPTTJ 04DIAMETER,MAJOR,FORWARD END TAPER FORWARD END TAPER MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CIRCULAR CROSS SECTION OF THE FORWARD END TAPERED PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPTWJ 04WIDTH,SLOT,MOUNTING FACILITY MOUNTING FACILITY SLOT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING FACILITY SLOT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CPTXJ 04LENGTH,SLOT,MOUNTING FACILITY MOUNTING FACILITY SLOT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING FACILITY SLOT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPTYD 19UNIT,GRADUATION GRADUATION UNIT THE INCREMENT OF MEASURE REPRESENTED BY THE MARKING(S) ON THE ITEM. SELECT REPLY CODE 10AJ40 CPTZD 19UNIT,GRADUATION,SMALLEST SMALLEST GRADUATION UNIT THE SMALLEST INCREMENT OF MEASURE ON THE ITEM. SELECT REPLY CODE 10AK09 CPWBD /D/ 11METHOD,DISTRIBUTION,SPARK SPARK DISTRIBUTION METHOD THE MEANS BY WHICH THE SPARK IS TRANSFERRED FROM THE ROTOR TO THE SPARK PLUG TERMINALS. SELECT REPLY CODE 10AF04 CPWCJ 13THREAD DIAMETER,ACCOMMODATION,SPARK PLUG TERMINAL SPARK PLUG TERMINAL ACCOMMODATION THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SPARK PLUG TERMINAL ACCOMMODATION WHICH WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD. 2D AND 1B MODE REPLY21AA051AC20 CPWDA /D/ 13THREAD QUANTITY PER INCH,ACCOMMODATION,SPARK PLUG TERMINAL SPARK PLUG TERMINAL ACCOMMODATION THREAD QUANTITY PER INCH THE NUMBER OF SCREW THREADS ON THE SPARK PLUG TERMINAL ACCOMMODATION PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CPWFA /D/ 13THREAD QUANTITY PER INCH,COIL TERMINAL ACCOMMODATION COIL TERMINAL ACCOMMODATION THREAD QUANTITY PER INCH THE NUMBER OF SCREW THREADS ON THE ITEM PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CPWGJ 10CAPACITY,MEASUREMENT MEASUREMENT CAPACITY THE VALUE WHICH THE ITEM IS CAPABLE OF MEASURING. 1D AND 1B MODE REPLY12AJ20 CPWHJ /D/ 13THREAD DIAMETER,ACCOMMODATION,PRIMARY TERMINAL PRIMARY TERMINAL ACCOMMODATION THREAD DIAMETER A MEASUREMENT OF THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COAXIAL CYLINDER IN PLAN VIEW WHICH WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD. 2D AND 1B MODE REPLY21AA051AC20 CPWJA /D/ 13THREAD QUANTITY PER INCH,ACCOMMODATION,PRIMARY TERMINAL PRIMARY TERMINAL ACCOMMODATION THREAD QUANTITY PER INCH THE NUMBER OF SCREW THREADS ON THE PRIMARY TERMINAL ACCOMMODATION PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CPWKA 19ARRANGEMENT,CONTACT CONTACT ARRANGEMENT THE DESIGNATION THAT IDENTIFIES THE SCHEMATIC DIAGRAM OF THE CONTACT CONFIGURATION. 1A MODE REPLY 0 CPWLA 12QUANTITY,WINDING,COIL COIL WINDING QUANTITY THE NUMBER OF COIL WINDING(S) PROVIDED. 1A MODE REPLY 0 CPWMD 19CHARACTERISTIC,WINDING WINDING CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC(S) OF A WINDING. SELECT REPLY CODE 10AC02 CPWND /D/ 13THREAD SERIES,FACILITY,MOUNTING MOUNTING FACILITY THREAD SERIES A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CPWPJ 10RESISTANCE RATING,DC,COIL PULL-IN COIL PULL-IN DC RESISTANCE RATING THE AMOUNT OF DIRECT CURRENT RESISTANCE REQUIRED TO ACTIVATE THE COIL PULL-IN. 2D AND 1B MODE REPLY21AA571AC20 CPWQJ 10RESISTANCE RATING,DC,COIL HOLD-IN COIL HOLD-IN DC RESISTANCE RATING THE AMOUNT OF DIRECT CURRENT RESISTANCE REQUIRED TO MAINTAIN OPERATION OF THE COIL HOLD-IN. 2D AND 1B MODE REPLY21AA571AC20 CPWRJ /D/ 13THREAD DIAMETER,FACILITY,MOUNTING MOUNTING FACILITY THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COAXIAL CYLINDER IN PLAN VIEW WHICH WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD. PLEASE USE MRC CDTF IN PLACE OF THIS CANCELED MRC. 2D AND 1B MODE REPLY21AA051AC20 CPWSA /D/ 13THREAD QUANTITY PER INCH,FACILITY,MOUNTING MOUNTING FACILITY THREAD QUANTITY PER INCH THE NUMBER OF SCREW THREADS ON THE MOUNTING FACILITY PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. PLEASE USE MRC CDTG IN PLACE OF THIS DISCONTINUED MRC. 1A MODE REPLY 0 CPWTB /D/ 10ROTATION IN DEG,SHAFT SHAFT ROTATION IN DEG THE MEASUREMENT OF THE SHAFT ROTATION,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CPWWJ 04LENGTH BEYOND WHEEL SIDE,PROJECTION,HUB HUB PROJECTION LENGTH BEYOND WHEEL SIDE A MEASUREMENT OF THE LONGEST DIMENSION OF THE HUB PROJECTION BEYOND THE WHEEL SIDE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPWXD 18TYPE,KEYWAY KEYWAY TYPE INDICATES THE TYPE OF KEYWAY PROVIDED. SELECT REPLY CODE 10AK54 CPWYA 12QUANTITY,SETSCREW SETSCREW QUANTITY THE NUMBER OF SETSCREW CONTAINED IN OR ON THE ITEM. 1A MODE REPLY 0 CPWZG 13THREAD SIZE AND LOCATION THREAD SIZE AND LOCATION DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE AND ITS LOCATION. FULL TEXT WRITE-IN 0 CPXBG /D/ 04SIZE AND LOCATION,STOCK STOCK SIZE AND LOCATION DESIGNATES THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE STOCK AND ITS LOCATION. FULL TEXT WRITE-IN 0 CPXCJ /D/ 10TIME IN SECONDS,TRIPPING TRIPPING TIME IN SECONDS THE LENGTH OF TIME THAT AN OVERLOAD MAY EXIST BEFORE THE DEVICE WILL TRIP,EXPRESSED IN SECONDS. 2D AND 1B MODE REPLY21AC201AE69 CPXDB /D/ 13SCREW THREAD PER UNIT OF MEASURE,MOUNTING FACILITY MOUNTING FACILITY SCREW THREAD PER UNIT OF MEASURE THE NUMBER OF SCREW THREADS ON THE ITEM MEASURED ON A LINE PARALLEL TO THE THREAD AXIS INCLUDING INCOMPLETE THREADS. 1B MODE REPLY 0 CPXFD /D/ 07INDICATOR,PROGRESS PROGRESS INDICATOR AN INDICATION OF WHETHER OR NOT A PROGRESS INDICATOR IS PROVIDED. SELECT REPLY CODE 10AB22 CPXGA 19CAPACITY,TOTALIZING,DIGIT DIGIT TOTALIZING CAPACITY THE NUMBER OF DIGITS THAT CAN BE TOTALED. 1A MODE REPLY 0 CPXHD /D/ 07FEATURE,MULTIPLICATION,AUTOMATIC AUTOMATIC MULTIPLICATION FEATURE AN INDICATION OF WHETHER OR NOT AN AUTOMATIC MULTIPLICATION FEATURE IS INCLUDED. SELECT REPLY CODE 10AA49 CPXJG /D/ 19COMPUTATION,UNIT,KEYBOARD SMALLEST FRACTIONAL KEYBOARD SMALLEST FRACTIONAL UNIT COMPUTATION THE SMALLEST FRACTIONAL UNIT THE KEYBOARD IS ARRANGED TO COMPUTE. FULL TEXT WRITE-IN 0 CPXKJ /D/ 04RADIUS,EDGE,ROUNDED ROUNDED EDGE RADIUS A MEASUREMENT OF A STRAIGHT LINE EXTENDING FROM THE CENTER OF A CIRCLE TO THE ROUNDED EDGE. 2D AND 1B MODE REPLY21AA051AC20 CPXLD /D/ 07FACILITIES,MOUNTING,DECK DECK MOUNTING FACILITIES AN INDICATION OF WHETHER OR NOT DECK MOUNTING FACILITIES ARE INCLUDED. SELECT REPLY CODE 10AA49 CPXMA /D/ 12QUANTITY,CRADLE CRADLE QUANTITY THE NUMBER OF CRADLES PROVIDED ON THE ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1A MODE REPLY 0 CPXNJ /D/ 04DEPTH,CRADLE CRADLE DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON A CRADLE,IN DISTINCTION FROM HEIGHT. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 CPXPJ /D/ 04WIDTH,CRADLE CRADLE WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CRADLE,IN DISTINCTION FROM THICKNESS. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 CPXQJ 04HEIGHT ACCOMMODATED,MAXIMUM RECORD FORM MAXIMUM RECORD FORM HEIGHT ACCOMMODATED THE MAXIMUM RECORD FORM HEIGHT THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 CPXRJ 04WIDTH ACCOMMODATED,MAXIMUM,RECORD FORM RECORD FORM MAXIMUM WIDTH ACCOMMODATED THE MAXIMUM WIDTH OF THE RECORD FORM THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 CPXSD /D/ 07BOARD,POSTING POSTING BOARD AN INDICATION OF WHETHER OR NOT A POSTING BOARD IS INCLUDED. SELECT REPLY CODE 10AA49 CPXTD 19POSITION,BOARD,POSTING POSTING BOARD POSITION AN INDICATION OF THE POSTING BOARD POSITION. SELECT REPLY CODE 10AK54 CPXWJ 04WIDTH,SURFACE,LOWER LOWER SURFACE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CPXXA 12QUANTITY,CONTROL,SELECTION SELECTION CONTROL QUANTITY THE NUMBER OF SELECTION CONTROLS PROVIDED. 1A MODE REPLY 0 CPXYJ /D/ 04DISTANCE BETWEEN DOUBLE FLANGES DISTANCE BETWEEN DOUBLE FLANGES THE DISTANCE MEASURED BETWEEN THE DOUBLE FLANGES ON AN ITEM. 2D AND 1B MODE REPLY21AA051AC20 CPXZD /D/ 07EJECTION,TRAY,AUTOMATIC AUTOMATIC TRAY EJECTION AN INDICATION OF WHETHER OR NOT AUTOMATIC TRAY EJECTION IS INCLUDED. SELECT REPLY CODE 10AA49 CPYBD /D/ 07BACKING,ADHESIVE,PRESSURE SENSITIVE PRESSURE SENSITIVE ADHESIVE BACKING AN INDICATION OF WHETHER OR NOT A PRESSURE SENSITIVE ADHESIVE BACKING IS INCLUDED. SELECT REPLY CODE 10AA49 CPYCG /D/ 12QUANTITY,TRAY,CRADLE CRADLE TRAY QUANTITY THE NUMBER OF CRADLE TRAYS PROVIDED. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. FULL TEXT WRITE-IN 0 CPYDJ /D/ 04HEIGHT,TRAY TRAY HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A TRAY,IN DISTINCTION FROM DEPTH. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 CPYFJ 04LENGTH,OUTSIDE,SMALL END SMALL END OUTSIDE LENGTH AN OUTSIDE MEASUREMENT OF THE LONGEST DIMENSION OF THE SMALL END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPYGJ 04DIAMETER,INSIDE,END END INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE END,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CPYHJ 04WIDTH,INSIDE,END END INSIDE WIDTH AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE END,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CPYJJ 04WIDTH,INSIDE,LARGE END LARGE END INSIDE WIDTH AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE LARGE END,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CPYKJ 04WIDTH,INSIDE,SMALL END SMALL END INSIDE WIDTH AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SMALL END,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CPYLJ 04LENGTH,INSIDE,END END INSIDE LENGTH A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF THE END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPYMJ 04LENGTH,INSIDE,LARGE END LARGE END INSIDE LENGTH A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF THE LARGE END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPYNJ 04LENGTH,NEUTRAL NEUTRAL LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM WHEN IT IS IN A NEUTRAL POSITION. 2D AND 1B MODE REPLY21AA051AC20 CPYPJ 04WIDTH,OUTSIDE,LARGE END LARGE END OUTSIDE WIDTH AN OUTSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE LARGE END,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CPYQJ 04WIDTH,OUTSIDE,SMALL END SMALL END OUTSIDE WIDTH AN OUTSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SMALL END,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CPYRJ 04LENGTH,OUTSIDE,END END OUTSIDE LENGTH A MEASUREMENT OF THE LONGEST OUTSIDE DIMENSION OF THE END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPYSJ 04LENGTH,OUTSIDE,LARGE END LARGE END OUTSIDE LENGTH A MEASUREMENT OF THE LONGEST OUTSIDE DIMENSION OF THE LARGE END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPYTJ 04LENGTH,INSIDE,SMALL END SMALL END INSIDE LENGTH A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF THE SMALL END,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPYWJ 04THICKNESS BETWEEN ENDS THICKNESS BETWEEN ENDS A MEASUREMENT OF THE SMALLEST DIMENSION BETWEEN THE ENDS OF THE ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPYXJ 04THICKNESS AT BOTH ENDS THICKNESS AT BOTH ENDS A MEASUREMENT OF THE SMALLEST DIMENSION OF BOTH ENDS OF THE ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CPYYG 10PRESSURE,DIFFENENTIAL,MAXIMUM MAXIMUM DIFFERENTIAL PRESSURE THE MAXIMUM DIFFERENTIAL PRESSURE WHICH THE ITEM IS CAPABLE OF WITHSTANDING WITHOUT EVIDENCE OF DEFORMATION OR OTHER DAMAGE. FULL TEXT WRITE-IN 0 CPYZG /D/ 10CAPACITY RATING CAPACITY RATING A MEASUREMENT OF THE CAPACITY OF AN ITEM. FULL TEXT WRITE-IN 0 CPZBD /D/ 07REGISTER,INTEGRATOR,TOTALIZING TOTALIZING INTEGRATOR REGISTER AN INDICATION OF WHETHER OR NOT A TOTALIZING INTEGRATOR REGISTER IS INCLUDED. SELECT REPLY CODE 10AA49 CPZCA 12QUANTITY,WHEEL,FIGURE FIGURE WHEEL QUANTITY THE NUMBER OF FIGURE WHEELS PROVIDED. 1A MODE REPLY 0 CPZDG 04SIZE,CONNECTION,INLET INLET CONNECTION SIZE DESIGNATES THE SIZE OF THE INLET CONNECTION INCLUDED ON THE ITEM. FULL TEXT WRITE-IN 0 CPZFA 12QUANTITY,TUBE,METERING METERING TUBE QUANTITY THE NUMBER OF METERING TUBES PROVIDED. 1A MODE REPLY 0 CPZGB 10CAPACITY IN GALLONS PER MINUTE,WATER,MAXIMUM MAXIMUM WATER CAPACITY IN GALLONS PER MINUTE THE MAXIMUM AMOUNT OF WATER FOR WHICH THE ITEM IS RATED,EXPRESSED IN GALLONS PER MINUTE. 1B MODE REPLY 0 CPZHB 10CAPACITY IN CUBIC FEET PER MINUTE,AIR,MAXIMUM MAXIMUM AIR CAPACITY IN CUBIC FEET PER MINUTE THE MAXIMUM AMOUNT OF AIR FOR WHICH THE ITEM IS RATED,EXPRESSED IN CUBIC FEET PER MINUTE. 1B MODE REPLY 0 CPZJG 10INCREMENT,SMALLEST,DIAL SCALE DIAL SCALE SMALLEST INCREMENT THE SMALLEST INCREMENT OF GRADUATION ON THE DIAL SCALE. FULL TEXT WRITE-IN 0 CPZKD /D/ 07POINTER,REFERENCE,DIAL SCALE DIAL SCALE REFERENCE POINTER AN INDICATION OF WHETHER OR NOT A DIAL SCALE REFERENCE POINTER IS INCLUDED. SELECT REPLY CODE 10AA49 CPZLA 12QUANTITY PER TUBE,FLOAT FLOAT QUANTITY PER TUBE THE NUMBER OF FLOATS IN EACH TUBE. 1A MODE REPLY 0 CPZMD /D/ 07FLOAT,SPINNING SPINNING FLOAT AN INDICATION OF WHETHER OR NOT A SPINNING FLOAT IS INCLUDED. SELECT REPLY CODE 10AA49 CPZND /D/ 07DAMPENER,PULSATION,INTEGRAL INTEGRAL PULSATION DAMPENER AN INDICATION OF WHETHER OR NOT AN INTEGRAL PULSATION DAMPENER IS INCLUDED. SELECT REPLY CODE 10AA49 CPZPD 19POSITION FOR WHICH DESIGNED,CONNECTION,INLET INLET CONNECTION POSITION FOR WHICH DESIGNED THE INLET CONNECTION POSITION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AM84 CPZQD 18TYPE,DEVICE,INLET CONNECTION INLET CONNECTION DEVICE TYPE INDICATES THE TYPE OF INLET CONNECTION DEVICE PROVIDED. SELECT REPLY CODE 10AK95 CPZRD 19POSITION FOR WHICH DESIGNED,CONNECTION,OUTLET OUTLET CONNECTION POSITION FOR WHICH DESIGNED THE OUTLET CONNECTION POSITION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AM84 CPZSD 18TYPE,DEVICE,OUTLET CONNECTION OUTLET CONNECTION DEVICE TYPE INDICATES THE TYPE OF OUTLET CONNECTION DEVICE PROVIDED. SELECT REPLY CODE 10AK95 CPZTD /D/ 07SIGNAL,ALARM ALARM SIGNAL AN INDICATION OF WHETHER OR NOT AN ALARM SIGNAL IS INCLUDED. SELECT REPLY CODE 10AA49 CPZWJ 10KILOVOLT-AMPERE RATING KILOVOLT-AMPERE RATING THE AMOUNT OF APPARENT POWER,AS DISTINGUISHED FROM TRUE POWER,FOR WHICH THE ITEM IS RATED,EXPRESSED IN KILOVOLT-AMPERES. 1D AND 1B MODE REPLY11AC20 CPZXJ 04LENGTH UNDER CAP HEAD LENGTH UNDER CAP HEAD NONE. 2D AND 1B MODE REPLY21AA051AC20 CPZYJ 04HEIGHT,HEAD,CAP CAP HEAD HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CPZZJ 04WIDTH,EAR EAR WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQBBD 19RELATIONSHIP WITH FIRST END,SECOND END SECOND END RELATIONSHIP WITH FIRST END INDICATES WHETHER OR NOT THE SECOND END IS IDENTICAL TO THE FIRST END. SELECT REPLY CODE 10AN69 CQBCJ A10STRENGTH,TENSILE,MINIMUM MINIMUM TENSILE STRENGTH THE MAXIMUM RATED LOAD IN TENSION APPLIED IN A LONGITUDINAL DIRECTION,PER UNIT OF CROSS-SECTIONAL AREA,THAT THE MATERIAL CAN WITHSTAND WITHOUT RUPTURE. 1D AND 1A MODE REPLY11AN71 CQBDJ 10PRESSURE,TEST,BURST BURST TEST PRESSURE THE MINIMUM INTERNAL PRESSURE RATING,DETERMINED BY DESTRUCTION TESTS,AT WHICH THE ITEM CAN BE EXPECTED TO RUPTURE. 1D AND 1B MODE REPLY11AN71 CQBFJ 10RESISTANCE AT MAXIMUM OPERATING TEMP,INSULATION INSULATION RESISTANCE AT MAXIMUM OPERATING TEMP DIRECT CURRENT RESISTANCE BETWEEN TWO CONDUCTORS THAT ARE SEPARATED BY AN INSULATING MATERIAL,MEASURED AT THE MAXIMUM OPERATING TEMPERATURE OF THE ITEM. 1D AND 1B MODE REPLY12AN86 CQBGD /D/ 07CAPABILITY,ACTION,FIRST END SWIVEL FIRST END SWIVEL ACTION CAPABILITY AN INDICATION OF WHETHER OR NOT THE END HAS THE CAPABILITY TO ROTATE. SELECT REPLY CODE 10AN90 CQBHJ 04RADIUS,END,FIRST FIRST END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CQBJJ 04THICKNESS,TOP TOP THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CQBKJ /D/ 04DISTANCE BETWEEN TERMINALS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN TERMINALS NONE. 2D AND 1B MODE REPLY21AA051AC20 CQBLJ /D/ 04SPACING,HOLE,FIFTH MOUNTING FIFTH MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 CQBMJ /D/ 04WIDTH,CLAMP,MOUNTING MOUNTING CLAMP WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQBNH 18TYPE AND TREAD DESIGN,SERVICE SERVICE TYPE AND TREAD DESIGN INDICATES THE PRIMARY TYPE OF SERVICE FOR WHICH THE ITEM IS DESIGNED AND THE DESIGN OF THE TREAD. 3D MODE REPLY 32AN782AN792AN80 CQBPH /D/ 13SCREW THREAD SERIES DESIGNATOR AND LOCATION SCREW THREAD SERIES DESIGNATOR AND LOCATION A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER,AND THE THREAD LOCATION. 2D MODE REPLY 23AN732AH06 CQBQJ 10CAPACITANCE VALUE PER SECTION CAPACITANCE VALUE PER SECTION THE RELATIVE LEVEL OF THE QUANTITY OF ELECTRIC CHARGE AT A GIVEN POTENTIAL WHICH THE CAPACITOR IS CAPABLE OF RECEIVING AND STORING PER SECTION. 2D AND 1B MODE REPLY22AN862AH19 CQBRJ 04LENGTH,SLOT,FIRST RELIEF FIRST RELIEF SLOT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQBSJ 04WIDTH,KEY,FIRST FIRST KEY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQBTJ 04DEPTH,HOLE,PIN PIN HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQBWJ 10SPACING,HOLE,SEVENTH SEVENTH HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 CQBXJ 04DISTANCE FROM CONDUCTOR SLOT TO OPPOSITE SURFACE,SECOND SECOND DISTANCE FROM CONDUCTOR SLOT TO OPPOSITE SURFACE NONE. 2D AND 1B MODE REPLY21AA051AC20 CQBYJ 04WIDTH,SHACKLE SHACKLE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQBZJ 04DEPTH,SLOT,SECOND SECOND SLOT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQCBH /D/ 17SURFACE TREATMENT AND LOCATION SURFACE TREATMENT AND LOCATION THE PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE ITEM,AND ITS LOCATION. 3D MODE REPLY 33AN731AN986AD09 CQCCJ 10RESISTANCE PER SECTION,ELECTRICAL ELECTRICAL RESISTANCE PER SECTION A MEASURE OF THE OPPOSITION TO THE FLOW OF DIRECT OR ALTERNATING CURRENT PER SECTION. 2D AND 1B MODE REPLY22AN862AH19 CQCDJ /D/ 10CURVE AT SPECIFIC PERCENT RESISTANCE CHANGE PER SECTION TAPER,NONSTANDARD NONSTANDARD CURVE AT SPECIFIC PERCENT RESISTANCE CHANGE PER SECTION TAPER THE RATE OF CHANGE AND DISTRIBUTION OF RESISTANCE,IN RELATION TO THE ROTATION OF THE CONTROL SHAFT OF A VARIABLE RESISTOR PER SECTION,THAT ESTABLISHES A CURVE THAT CANNOT BE IDENTIFIED TO A STANDARD TAPER CURVE. 3D AND 1B MODE REPLY31AC831AC842AH19 CQCFD 19CONSTRUCTION CONSTRUCTION THE STRUCTURAL CHARACTERISTIC OF THE ITEM. SELECT REPLY CODE 10AN70 CQCGJ 04DISTANCE FROM CENTERLINE OF HOLE TO STUD END DISTANCE FROM CENTERLINE OF HOLE TO STUD END NONE. 2D AND 1B MODE REPLY21AA051AC20 CQCHJ 08LOCATION FROM CCW TERMINAL PER SECTION IN DEG OF EFFECTIVE ELECTRICAL ROTATION,TAP TAP LOCATION FROM CCW TERMINAL PER SECTION IN DEG OF EFFECTIVE ELECTRICAL ROTATION THE LOCATION PER SECTION,IN DEGREES,OF EFFECTIVE ELECTRICAL ROTATION BETWEEN THE COUNTERCLOCKWISE TERMINAL OF A RESISTOR AND EACH TAP TERMINAL. 1D AND 1B MODE REPLY12AH19 CQCJJ 10PRESSURE AND MEDIA FOR WHICH DESIGNED,OPERATING,MAXIMUM MAXIMUM OPERATING PRESSURE AND MEDIA FOR WHICH DESIGNED THE MAXIMUM PRESSURE AT WHICH AN ITEM IS RATED TO OPERATE FOR EACH TYPE OF SERVICE WITH WHICH AN ITEM MAY BE USED. 2D AND 1B MODE REPLY21AN713AN91 CQCKJ 10TRAVEL IN ANGULAR DEG,ACTUATOR,ROTARY ROTARY ACTUATOR TRAVEL IN ANGULAR DEG THE MEASUREMENT OF THE ROTARY MECHANICAL MOTION OF THE ACTUATING SHAFT OF AN ITEM,EXPRESSED IN DEGREES. 1D AND 1B MODE REPLY11AC20 CQCLJ 04THICKNESS,FLANGE,INSERT INSERT FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CQCMJ 04DISTANCE BETWEEN CENTER TERMINAL AND OUTSIDE TERMINAL,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN CENTER TERMINAL AND OUTSIDE TERMINAL THE CENTER TO CENTER DISTANCE BETWEEN THE CENTER TERMINAL AND THE OUTSIDE TERMINAL. 2D AND 1B MODE REPLY21AA051AC20 CQCNJ 10PRESSURE,OPERATING,POWER DRIVE POWER DRIVE OPERATING PRESSURE THE PRESSURE REQUIRED TO ACTUATE THE POWER DRIVEN UNIT. 2D AND 1B MODE REPLY21AN711AC20 CQCPJ 10DIFFERENTIAL,PRESSURE,OPERATING,INLET/OUTLET INLET/OUTLET OPERATING PRESSURE DIFFERENTIAL THE DIFFERENCE,AT THE RATED TEMPERATURE,BETWEEN THE INLET AND OUTLET PRESSURE FOR POSITIVE OPERATION. 2D AND 1B MODE REPLY21AN711AC20 CQCQJ 04THICKNESS,TONGUE,FIRST FIRST TONGUE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CQCRD 13THREAD SERIES DESIGNATOR,END,FOURTH FOURTH END THREAD SERIES DESIGNATOR A DESIGNATOR DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CQCSH 19COMPOSITION AND LOCATION,LAYER LAYER COMPOSITION AND LOCATION THE MATERIAL AND FORMATION IDENTIFYING THE STRUCTURAL CHARACTERISTIC/S/ OF THE ITEM AND LOCATION. 2D MODE REPLY 21AN922AD14 CQCTD 18TYPE,CONTAINER,PRIMARY PRIMARY CONTAINER TYPE INDICATES THE TYPE OF CONTAINER/S/ OR SUPPORTING DEVICE/S/ WHICH IS IN DIRECT CONTACT WITH THE ITEM. SELECT REPLY CODE 10AN65 CQCWJ A18TYPE,END,FEEDTHRU CONNECTION FEEDTHRU CONNECTION END TYPE INDICATES THE TYPE OF CONDUCTOR CONNECTION FACILITY/IES/ FURNISHED ON EACH END OF A FEEDTHRU TERMINAL. 2D AND 1A MODE REPLY21AN951AN96 CQCXD 11METHOD,RETENTION,TIRE AIR TIRE AIR RETENTION METHOD THE MEANS USED TO RETAIN AIR INSIDE THE TIRE. SELECT REPLY CODE 10AA32 CQCYJ T10RANGE,PRESSURE,ADJUSTABLE ADJUSTABLE PRESSURE RANGE THE MINIMUM TO MAXIMUM PRESSURES AT WHICH THE ITEM MAY BE SET TO OPEN. 1D AND 1F MODE REPLY11AN71 CQCZJ A12QUANTITY,LINK,TERMINAL CONNECTING TERMINAL CONNECTING LINK QUANTITY THE NUMBER OF TERMINAL CONNECTING LINKS FURNISHED WITH THE ITEM. 1D AND 1A MODE REPLY12AK17 CQDBJ T10RANGE PER SECTION IN PERCENT,CHARACTERISTIC,RESISTANCE TEMP RESISTANCE TEMP CHARACTERISTIC RANGE PER SECTION IN PERCENT THE CHANGE IN TOTAL RESISTANCE OVER A SPECIFIED TEMPERATURE RANGE PER SECTION,EXPRESSED AS A PERCENT OF THE TOTAL RESISTANCE AT A SPECIFIED REFERENCE TEMPERATURE. 2D AND 1F MODE REPLY22AC902AH19 CQDCJ A12QUANTITY PER SET,RECEPTACLE,COMMON FEEDTHRU COMMON FEEDTHRU RECEPTACLE QUANTITY PER SET THE NUMBER OF TAPER PIN RECEPTACLES WHICH COMPRISES A SET OF COMMON FEEDTHRU RECEPTACLES IN AN ITEM. 1D AND 1A MODE REPLY11AN97 CQDDJ 10SPACING,HOLE,THIRD MOUNTING THIRD MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 CQDFA /D/ 13THREAD QUANTITY PER INCH,END,FOURTH FOURTH END THREAD QUANTITY PER INCH THE NUMBER OF THREADS PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CQDGJ 04LENGTH,SKIRT SKIRT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQDHJ 04RADIUS,SIDE,SECOND SECOND SIDE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CQDJJ /D/ 04DIAMETER,CIRCLE,INNER TERMINAL INNER TERMINAL CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQDKA 19ARRANGEMENT,FORM,PILE-UP CONTACT PILE-UP CONTACT FORM ARRANGEMENT THE BASIC CONTACT FORMS,IN THE ORDER OF ASSEMBLAGE,THAT COLLECTIVELY DESCRIBE THE SWITCHING STRUCTURE OF A PILE-UP CONTACT GROUP. 1A MODE REPLY 0 CQDLJ 10SPACING,HOLE,FOURTH FOURTH HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 CQDMJ /D/ 04SPACING,HOLE,SEVENTH MOUNTING SEVENTH MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 CQDNJ 04WIDTH,SLOT,FIRST FIRST SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQDPA /D/ 03DESIGNATOR,TYPE TYPE DESIGNATOR A CONTROLLED DESIGNATION WHICH GIVES,IN CODE FORM,THE PRINCIPLE MECHANICAL AND ELECTRICAL CHARACTERISTICS OF THE ITEM AFFECTING INTERCHANGEABILITY. 1A MODE REPLY 0 CQDQJ /D/T13THREAD PITCH DIAMETERS,INLET INLET THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 CQDRJ 10LOSS AT REFERENCE FREQUENCY PER FUNCTION IN DECIBELS,INSERTION INSERTION LOSS AT REFERENCE FREQUENCY PER FUNCTION IN DECIBELS THE RATIO PER FUNCTION OF THE POWER DELIVERED TO THE LOAD BEFORE INSERTION OF THE FILTER TO THE POWER DELIVERED TO THE LOAD AFTER INSERTION OF THE FILTER,EXPRESSED IN DECIBELS. 1D AND 1B MODE REPLY12AF15 CQDSJ /D/ 10STIMULUS RATING,POINT,CONTACT ACTUATION CONTACT ACTUATION POINT STIMULUS RATING THE VALUE OF THE STIMULUS AT WHICH THE CONTACTS ACTUATE. 2D AND 1B MODE REPLY22AG201AC20 CQDTD /D/ 13THREAD SERIES DESIGNATOR,BULKHEAD BULKHEAD THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CQDWJ A18TYPE AND QUANTITY,TERMINAL,FUNCTIONAL FUNCTIONAL TERMINAL TYPE AND QUANTITY INDICATES THE FUNCTIONAL TYPE AND NUMBER OF TERMINALS PROVIDING ELECTRICAL CONNECTION TO THE ITEM. 2D AND 1A MODE REPLY23AN891AC00 CQDXJ /D/ 10FREQUENCY RATING IN HERTZ PER VOLTAGE REFERENCE,CONTACT CONTACT FREQUENCY RATING IN HERTZ PER VOLTAGE REFERENCE THE FREQUENCY AT WHICH THE CONTACTS ARE RATED PER VOLTAGE REFERENCE. 1D AND 1B MODE REPLY12AD88 CQDYJ /D/ 10LIMITS PER FUNCTION,VOLTAGE,SIGNAL INPUT SIGNAL INPUT VOLTAGE LIMITS PER FUNCTION THE LOWER AND UPPER VALUES,PER FUNCTION,OF THE NOMINAL SIGNAL VOLTAGE WHICH THE ITEM MAY HAVE APPLIED TO ITS INPUT TERMINALS. 2D AND 1B MODE REPLY22AF151AB63 CQDZJ 10VOLTAGE,AC RMS,DIELECTRIC WITHSTANDING,MAXIMUM MAXIMUM DIELECTRIC WITHSTANDING AC RMS VOLTAGE THE MAXIMUM ALTERNATING CURRENT ROOT MEAN SQUARE VOLTAGE THAT THE INSULATING MATERIAL/S/ OF THE ITEM WILL WITHSTAND WITHOUT RESULTING IN DISRUPTIVE DISCHARGE OR DETERIORATION. 2D AND 1B MODE REPLY21AB631AD86 CQFBJ T10LIMITS PER SECTION IN PERCENT CAPACITANCE CHANGE,TEMP,VOLTAGE VOLTAGE TEMP LIMITS PER SECTION IN PERCENT CAPACITANCE CHANGE THE MAXIMUM PERMISSIBLE CAPACITANCE CHANGE PER SECTION WITH TEMPERATURE OVER THE OPERATING TEMPERATURE RANGE,MEASURED EITHER WITH OR WITHOUT RATED VOLTAGE APPLIED. 2D AND 1F MODE REPLY21AN882AH19 CQFCJ 10FREQUENCIES OF DISCRIMINATION PER FUNCTION,SPECIFIED SPECIFIED FREQUENCIES OF DISCRIMINATION PER FUNCTION THE SPECIFIED FREQUENCIES,PER FUNCTION,AT WHICH LOSSES IN SIGNAL STRENGTH ARE,BY DESIGN OR MEASUREMENT,ESTABLISHED IN A FILTER CIRCUIT. 2D AND 1B MODE REPLY21AE062AF15 CQFDJ 10RESISTANCE,NOMINAL,SECTION SECTION NOMINAL RESISTANCE A MEASURE OF THE NOMINAL OPPOSITION TO THE FLOW OF ELECTRIC CURRENT THROUGH THE SECTION. 1D AND 1B MODE REPLY11AA57 CQFFJ /D/ 04DIAMETER AND LOCATION,OUTSIDE OUTSIDE DIAMETER AND LOCATION THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE,AND ITS LOCATION. 3D AND 1B MODE REPLY31AA051AC203AN73 CQFGJ /D/ 04LENGTH,ENCLOSURE ENCLOSURE LENGTH NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 CQFHJ 13THREAD SIZE,NOMINAL,FOURTH END FOURTH END NOMINAL THREAD SIZE THE DESIGNATION WHICH IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE NOMINAL THREAD SIZE. 1D AND 1B MODE REPLY11AA05 CQFJJ 04DIAMETER,OUTSIDE,GAGING SURFACE GAGING SURFACE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GAGING SURFACE OF THE ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CQFKD 18TYPE,TERMINAL,FIXED TAP FIXED TAP TERMINAL TYPE INDICATES THE TYPE OF TERMINAL/S/ ON THE FIXED TAP/S/ THAT IS PROVIDED FOR ELECTRICAL CONNECTION. SELECT REPLY CODE 10AA58 CQFLJ T19TOLERANCE PER SECTION,CONFORMITY,FUNCTION FUNCTION CONFORMITY TOLERANCE PER SECTION THE PERMISSIBLE RANGE PER SECTION BY WHICH THE ACTUAL VALUE OF RESISTANCE OR VOLTAGE AT ANY SPECIFIED POINT MAY DEVIATE FROM THE THEORETICAL VALUE FOR THE LINEAR OR NONLINEAR FUNCTION,EXPRESSED AS A MINUS AND PLUS PERCENT. 1D AND 1F MODE REPLY12AH19 CQFMJ 10HARDNESS RATING HARDNESS RATING A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF AN ITEM WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE. 2D AND 1B MODE REPLY22AC261AC20 CQFNJ /D/ 04DIAMETER,COUNTERBORE,GEAR GEAR COUNTERBORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQFPJ 10SPACING,HOLE,TENTH TENTH HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 CQFQJ 04HEIGHT,OVERALL,PLATE PLATE OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CQFRJ /D/T10RANGE,ADJUSTMENT,CONTACT ACTUATION POINT CONTACT ACTUATION POINT ADJUSTMENT RANGE THE MINIMUM AND MAXIMUM LIMITS TO WHICH THE ACTUATION POINT OF THE CONTACTS MAY BE ADJUSTED. 1D AND 1F MODE REPLY12AG20 CQFSJ 04HEIGHT,CAP,FIRST FIRST CAP HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CQFTJ /D/ 13THREAD DIAMETER,TERMINAL,FUNCTIONAL FUNCTIONAL TERMINAL THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COAXIAL CYLINDER IN PLAN VIEW WHICH WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD ON A FUNCTIONAL TERMINAL. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC00 CQFWJ 04DISTANCE FROM KEY CENTER TO WIRE HOLE CENTER DISTANCE FROM KEY CENTER TO WIRE HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQFXJ 04DIAMETER,END,SMALL,PIN PIN SMALL END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALL END OF A CIRCULAR PIN,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CQFYJ 04LENGTH,HOLE,PLATE PLATE HOLE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQFZJ 04DEPTH,HOLE,STUD,CENTER CENTER STUD HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQGBD 19STIMULUS,ACTION,CONTACT CONTACT ACTION STIMULUS AN INDICATION OF WHETHER THE INITIAL ACTION OF THE CONTACTS OCCURS AS THE RESULT OF AN INCREASE OR DECREASE IN STIMULUS. SELECT REPLY CODE 10AG17 CQGCJ 10VOLTAGE RATING AND TYPE PER FUNCTION,OPERATING OPERATING VOLTAGE RATING AND TYPE PER FUNCTION THE LEVEL OF ELECTRICAL POTENTIAL AND TYPE OF CURRENT,PER FUNCTION,FOR WHICH THE ITEM IS DESIGNED. 3D AND 1B MODE REPLY31AB631AB622AF15 CQGDB /D/ 04TAPER PER FOOT IN INCHES TAPER PER FOOT IN INCHES NONE. 1B MODE REPLY 0 CQGFH /D/ 18TYPE AND LOCATION,ADJUSTMENT,CONTACT DEACTUATION POINT CONTACT DEACTUATION POINT ADJUSTMENT TYPE AND LOCATION INDICATES THE TYPE AND LOCATION OF THE DEVICE PROVIDED FOR MANUAL ADJUSTMENT OF THE CONTACT DEACTUATION POINT. 2D MODE REPLY 23AN732AG18 CQGGJ 04DISTANCE BETWEEN CONDUCTOR GROOVES,FIRST FIRST DISTANCE BETWEEN CONDUCTOR GROOVES NONE. 2D AND 1B MODE REPLY21AA051AC20 CQGHH /D/ 19FITTING/COMPONENT AND MATERIAL,END,FIRST FIRST END FITTING/COMPONENT AND MATERIAL THE NAME OF THE FITTING AND/OR COMPONENT AND THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH IT IS FABRICATED. 2D MODE REPLY 22AC426AD09 CQGJD 08LOCATION,INLET INLET LOCATION INDICATES THE LOCATION OF THE INLET ON THE ITEM. SELECT REPLY CODE 10AN73 CQGKD 18TYPE,CONTAINER,SECONDARY SECONDARY CONTAINER TYPE INDICATES THE TYPE OF CONTAINER(S) WHICH IS IN CONTACT WITH AND CONTAINS THE PRIMARY CONTAINER(S). SELECT REPLY CODE 10AN65 CQGLJ 04LENGTH,HOLE,FIRST FIRST HOLE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQGMJ 10PRESSURE,OPERATING,MAXIMUM MAXIMUM OPERATING PRESSURE THE MAXIMUM PRESSURE AT WHICH THE ITEM IS RATED FOR OPERATION. 1D AND 1B MODE REPLY11AN71 CQGNJ 10TEMP IN DEG CELSIUS PER SECTION AT ZERO PERCENT RATED POWER,AMBIENT AMBIENT TEMP IN DEG CELSIUS PER SECTION AT ZERO PERCENT RATED POWER THE AMBIENT TEMPERATURE AT WHICH THE POWER DISSIPATION OF EACH SECTION IS DERATED TO ZERO PERCENT OF THE FULL RATED POWER. 1D AND 1B MODE REPLY12AH19 CQGPH 19DENSITY AND LOCATION,OVERLAY OVERLAY DENSITY AND LOCATION THE DENSITY OF THE SURFACING MATERIAL AND ITS LOCATION ON THE ITEM. 2D MODE REPLY 22AG493AN73 CQGQJ /D/ 04WIDTH,KEYWAY,SEAT SEAT KEYWAY WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SEAT KEYWAY,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CQGRJ /D/ 04WIDTH,RING,OUTER,BEARING BEARING OUTER RING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQGSJ 04WIDTH,INSIDE,THIMBLE THIMBLE INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQGTL 16STYLE,FACE,CONTACT CONTACT FACE STYLE THE SYTLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CONTACT FACE. 1L MODE REPLY 0 CQGWJ 04ANGLE,SIDE SIDE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CQGXJ /D/ 04ANGLE BETWEEN CONDUCTOR ACCOMMODATIONS ANGLE BETWEEN CONDUCTOR ACCOMMODATIONS AN INDICATION OF THE ANGLE BETWEEN CONDUCTOR ACCOMMODATIONS. 2D AND 1B MODE REPLY21AP381AC20 CQGYJ /D/ 04DIAMETER,INSIDE,JOURNAL JOURNAL INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQGZJ /D/ 04LENGTH,CONNECTION,TOP TOP CONNECTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQHBJ /D/ 04DIAMETER,SHIELD SHIELD DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQHCD 08LOCATION,NAP NAP LOCATION INDICATES THE LOCATION OF AN ITEM WHICH IS NAPPED. SELECT REPLY CODE 10AN73 CQHDJ /D/ 04HEIGHT INCLUDING SEATING RING,BEARING BEARING HEIGHT INCLUDING SEATING RING NONE. 2D AND 1B MODE REPLY21AA051AC20 CQHFD 19SLOPE,GRAIN,MAXIMUM MAXIMUM GRAIN SLOPE INDICATES THE MAXMIUM SLOPE OF GRAIN IN RELATION TO THE LENGTH OF THE ITEM. SELECT REPLY CODE 10AP05 CQHGD 02DESIGN,FABRIC FABRIC DESIGN AN ARTISTIC OR MECHANICAL DESIGN THAT IS IMPRINTED ON,EMBODIED IN,OR OTHERWISE CAUSED TO BECOME AN INTEGRAL OR APPARENT PART OF THE FABRIC. SELECT REPLY CODE 10AF83 CQHHJ /D/ 04DISTANCE BETWEEN FIRST AND SECOND POSTS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FIRST AND SECOND POSTS NONE. 2D AND 1B MODE REPLY21AA051AC20 CQHJJ 04DIAMETER,INSIDE,WAVEGUIDE WAVEGUIDE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQHKD 02DESIGN,TRANSMISSION,LIGHT LIGHT TRANSMISSION DESIGN THE DESIGN CHARACTERISTIC WHICH CONTROLS THE EMERGENCE OF LIGHT. SELECT REPLY CODE 10AF93 CQHLJ /D/ 04RADIUS,RING,OUTER OUTER RING RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CQHMJ /D/ 04DISTANCE FROM MOUNTING HOLE CENTER TO MOUNTING END DISTANCE FROM MOUNTING HOLE CENTER TO MOUNTING END NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 CQHNJ 04WIDTH,OUTSIDE,WAVEGUIDE WAVEGUIDE OUTSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQHPJ 04ANGLE,INSIDE,LEFT LEFT INSIDE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CQHQJ A10STRENGTH,YIELD,MINIMUM MINIMUM YIELD STRENGTH THE STRESS AT WHICH A MATERIAL EXHIBITS A SPECIFIED LIMITING DEVIATION FROM THE PROPORTIONALITY OF STRESS OR STRAIN. 1D AND 1A MODE REPLY11AN71 CQHRJ /D/ 04LENGTH,TONGUE,MOUNTING CLAMP MOUNTING CLAMP TONGUE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQHSJ /D/ 04LENGTH,CLAMP,WIRE WIRE CLAMP LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQHTH 19CONDITION AND LOCATION,SURFACE SURFACE CONDITION AND LOCATION THE CONDITION OF THE ITEM WITH RESPECT TO THE TEXTURE OF THE SURFACE AND ITS LOCATION. 2D MODE REPLY 23AN732AN72 CQHWH /D/ 19FITTING/COMPONENT AND SURFACE TREATMENT,END,FIRST FIRST END FITTING/COMPONENT AND SURFACE TREATMENT THE NAME OF THE FITTING AND/OR COMPONENT AND THE PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE. 2D MODE REPLY 22AC426AD09 CQHXJ 04DISTANCE,CENTER,FIRST FIRST CENTER DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CQHYJ /D/ 04DISTANCE,CENTER TO CENTER,FASTENING FEATURE FASTENING FEATURE CENTER TO CENTER DISTANCE THE DISTANCE BETWEEN THE CENTER OF ONE FASTENING FEATURE AND THE CENTER OF THE ADJACENT FASTENING FEATURE. 2D AND 1B MODE REPLY21AA051AC20 CQHZJ /D/ 04WIDTH,RING,OUTER,NEEDLE BEARING NEEDLE BEARING OUTER RING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQJBJ 10PRESSURE,PROOF PROOF PRESSURE THE MAXIMUM PRESSURE THAT AN ITEM WILL WITHSTAND WITHOUT RESULTING IN ANY PERMANENT CHANGES IN THE STRUCTURAL,MECHANICAL,OR ELECTRICAL CHARACTERISTICS. 1D AND 1B MODE REPLY12AG20 CQJCJ /D/A04SIZE ACCOMMODATED AND QUANTITY,CONDUCTOR CONDUCTOR SIZE ACCOMMODATED AND QUANTITY THE SIZE AND NUMBER OF CONDUCTORS THE ITEM IS DESIGNED TO ACCOMMODATE. 2D AND 1A MODE REPLY21AA442AP07 CQJDJ 04DEPTH,KEY,FIRST FIRST KEY DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQJFJ /D/ 04DIAMETER,BORE,CONE CONE BORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQJGJ 04LENGTH,RECESS,BODY BODY RECESS LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQJHD 18TYPE,CONTAINER,TERTIARY TERTIARY CONTAINER TYPE INDICATES THE TYPE OF CONTAINER/S/ WHICH IS IN DIRECT CONTACT WITH AND CONTAINS THE SECONDARY CONTAINER/S/. SELECT REPLY CODE 10AN65 CQJJJ 10TEMP,OPERATING,NONDERATED NONDERATED OPERATING TEMP THE TEMPERATURE/S/ AT WHICH AN ITEM CAN FUNCTION WITHOUT VOLTAGE DERATING. 2D AND 1B MODE REPLY21AB361AC20 CQJKJ /D/ 04DISTANCE FROM LATERAL WATERPLUG CENTERLINE TO LONGITUDINAL WATERPLUG END DISTANCE FROM LATERAL WATERPLUG CENTERLINE TO LONGITUDINAL WATERPLUG END NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 CQJLB 10CARRYING RATING IN AMPS,CURRENT CURRENT CARRYING RATING IN AMPS THE AMOUNT OF ELECTRICAL CURRENT THE ITEM IS DESIGNED TO CARRY,EXPRESSED IN AMPERES. 1B MODE REPLY 0 CQJMJ /D/ 13THREAD LENGTH AND LOCATION THREAD LENGTH AND LOCATION A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL THREAD AXIS,AND THE LOCATION. PLEASE USE CCOMBINATION OF MRC AASA AND APJC IN PLACE OF THIS DISCONTINUED MRC. 3D AND 1B MODE REPLY33AN731AA051AC20 CQJND 19SIZE ACCOMMODATED,TIRE TIRE SIZE ACCOMMODATED THE TIRE SIZE/S/ THAT THE ITEM WILL ACCOMMODATE. SELECT REPLY CODE 10AA27 CQJPJ 04DISTANCE,OUTER EDGE TO NOTCH CENTER OUTER EDGE TO NOTCH CENTER DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CQJQJ 04LENGTH,BOLT BOLT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BOLT, IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CQJRJ 19PH,MEDIUM,CULTURE CULTURE MEDIUM PH THE DEGREE OF ACIDITY OR BASICITY OF THE PREPARED CULTURE MEDIUM DETERMINED AT ROOM TEMPERATURE /25 DEGREES CELSIUS/. 1D AND 1B MODE REPLY11AC20 CQJSJ 10POINT,DROPPING,MINIMUM MINIMUM DROPPING POINT THE LOWEST TEMPERATURE AT WHICH THE ITEM WILL DROP. 1D AND 1B MODE REPLY11AB36 CQJTD 19ADDITIVE,COLOR COLOR ADDITIVE SUBSTANCE EMPLOYED SOLELY FOR THE PURPOSE OF IMPARTING COLOR. SELECT REPLY CODE 10AP13 CQJWJ 04DIAMETER,RECESS,TOP TOP RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQJXJ 13THREAD SIZE,NOMINAL NOMINAL THREAD SIZE A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD. 1D AND 1B MODE REPLY11AA05 CQJYJ 18TYPE AND RATING IN AMPS,CURRENT CURRENT TYPE AND RATING IN AMPS INDICATES THE TYPE AND AMOUNT OF ELECTRICAL FLOW AT WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN AMPERES. 1D AND 1B MODE REPLY12AN87 CQJZJ 10CURRENT RATING AT MAXIMUM DC VOLTAGE RATING,CONTACT LOAD CONTACT LOAD CURRENT RATING AT MAXIMUM DC VOLTAGE RATING THE AMOUNT OF CURRENT THE CONTACTS ARE RATED TO MAKE OR BREAK AT MAXIMUM RATED DIRECT CURRENT VOLTAGE WITH A SPECIFIED LOAD. MRC DISCONTINUED FOR GENERAL USE,MRC MAINTAINED FOR DTRA USE ONLY. 2D AND 1B MODE REPLY21AC302AK53 CQKBH 18TYPE AND LOCATION,HOLE,SECURING SECURING HOLE TYPE AND LOCATION INDICATES THE TYPE OF SECURING HOLE AND THE LOCATION. 2D MODE REPLY 21AB683AN73 CQKCJ 04LENGTH,NOMINAL,POWER CABLE POWER CABLE NOMINAL LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE POWER CABLE. 1D AND 1B MODE REPLY11AA05 CQKDJ 04DISTANCE FROM FLANGE TO WIRE GROOVE EDGE DISTANCE FROM FLANGE TO WIRE GROOVE EDGE NONE. 2D AND 1B MODE REPLY21AA051AC20 CQKFA 19INSCRIPTION INSCRIPTION AN INDICATION OF THE INSCRIPTION ON THE ITEM,EXCLUDING PART NUMBER. 1A MODE REPLY 0 CQKGD 19CLASSIFICATION,FINENESS,PARTICLE PARTICLE FINENESS CLASSIFICATION THE FINENESS OF THE PARTICLES EXPRESSED IN DESCRIPTIVE TERMS AS RELATED TO A US STANDARD SIEVE. SELECT REPLY CODE 10AF67 CQKHJ 04DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO THE BASE OF AN ISOSCELES TRIANGLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO THE BASE OF AN ISOSCELES TRIANGLE THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE BASE OF AN ISOSCELES TRIANGLE. 2D AND 1B MODE REPLY21AA051AC20 CQKJG 04WIDTH,RANDOM RANDOM WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS. FULL TEXT WRITE-IN 0 CQKKA 13THREAD QUANTITY PER INCH,END,FIRST FIRST END THREAD QUANTITY PER INCH THE NUMBER OF THREADS PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CQKLH /D/ 11METHOD AND PUMP DESIGNATION,FLUID DRIVE,ROTARY ROTARY FLUID DRIVE METHOD AND PUMP DESIGNATION THE MEANS PROVIDED TO MOVE THE FLUID THROUGH THE ITEM,AND THE PUMP DESIGNATION. 2D MODE REPLY 23AK043AA96 CQKMD 14SHAPE,SURFACE,SEATING SEATING SURFACE SHAPE THE PHYSICAL CONFIGURATION OF THE SURFACE OF THE SEAT. SELECT REPLY CODE 10AP00 CQKNJ /D/ 04DEPTH,SWAGE SWAGE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQKPJ /D/ 04LENGTH,CONNECTION,BOTTOM BOTTOM CONNECTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQKQJ 04DISTANCE FROM BRUSH TOP TO HOLE CENTERLINE DISTANCE FROM BRUSH TOP TO HOLE CENTERLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 CQKRJ /D/ 04DIAMETER-LOCATION AND MEASURING METHOD DIAMETER-LOCATION AND MEASURING METHOD THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE,ITS LOCATION ON THE ITEM,AND THE MEASURING METHOD USED. 4D AND 1B MODE REPLY41AA051AC203AN732AN68 CQKSD 08LOCATION,FLANGE,MOUNTING MOUNTING FLANGE LOCATION INDICATES THE LOCATION OF THE MOUNTING FLANGE ON THE ITEM. SELECT REPLY CODE 10AN73 CQKTJ /D/ 10VOLTAGE IN VOLTS-CURRENT TYPE AND DESIGNATION,PRIME MOVER PRIME MOVER VOLTAGE IN VOLTS-CURRENT TYPE AND DESIGNATION THE TOTAL ELECTRICAL VOLTAGE,EXPRESSED IN VOLTS,AND THE TYPE OF CURRENT OF THE PRIME MOVER AND ITS DESIGNATION. 2D AND 1B MODE REPLY22AN871AP23 CQKWJ 04DIAMETER,INSIDE,STEPPED,BODY BODY STEPPED INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQKXJ 10FLOW RATE,AIR AIR FLOW RATE THE RATED CAPACITY OF AIR FLOW MOVED THROUGH THE ITEM. 2D AND 1B MODE REPLY22AG671AC20 CQKYJ 10SPACING,HOLE,FIRST MOUNTING FIRST MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 CQKZJ A18TYPE AND QUANTITY,PASSAGE,OIL OIL PASSAGE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF OIL PASSAGES INCLUDED ON THE ITEM. 1D AND 1A MODE REPLY11AB99 CQLBJ /D/ 04DISTANCE FROM LATERAL WATERPLUG END TO ENCLOSURE DISTANCE FROM LATERAL WATERPLUG END TO ENCLOSURE NONE. 2D AND 1B MODE REPLY21AA051AC20 CQLCD 08LOCATION,TAP,WINDING WINDING TAP LOCATION THE POINTS BETWEEN THE END TERMINALS OF A WINDING THAT PROVIDE ELECTRICAL CONNECTION TO INTERMEDIATE VALUES OF THE TOTAL WINDING. SELECT REPLY CODE 10AC05 CQLDJ 04LENGTH,NOMINAL,FLEXIBLE TUBE FLEXIBLE TUBE NOMINAL LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE FLEXIBLE TUBE. 1D AND 1B MODE REPLY11AA05 CQLFJ 04THICKNESS,GASKET GASKET THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CQLGD /D/ 13THREAD SERIES DESIGNATOR,INTERNAL,HEAD HEAD INTERNAL THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF HEAD INTERNAL THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A DIAMETER. SELECT REPLY CODE 10AH06 CQLHJ 10LEAKAGE AT MAXIMUM OPERATING TEMP,DC DC LEAKAGE AT MAXIMUM OPERATING TEMP STRAY DIRECT CURRENT OF RELATIVELY SMALL VALUE WHICH FLOWS THROUGH THE ITEM WHEN VOLTAGE IS IMPRESSED ACROSS IT,MEASURED AT MAXIMUM OPERATING TEMPERATURE. 1D AND 1B MODE REPLY12AN86 CQLJJ 04DIAMETER,GROOVE,MAJOR MAJOR GROOVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQLKJ /D/ 04DIAMETER,MAJOR,TAPERED MOUNTING TAPERED MOUNTING MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQLLJ 04DISTANCE BETWEEN CONDUCTOR GROOVES,SECOND SECOND DISTANCE BETWEEN CONDUCTOR GROOVES NONE. 2D AND 1B MODE REPLY21AA051AC20 CQLMJ 04RADIUS,END,SECOND SECOND END RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CQLNJ 04WIDTH,BEVEL BEVEL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQLPJ 04ANGLE,FIRST FIRST ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CQLQJ 10VISCOSITY AT RATED TEMP VISCOSITY AT RATED TEMP THE KINEMATIC UNITS (CENTISTOKES/MM 2/S) OF THE ITEM AT A RATED TEMPERATURE. 2D AND 1B MODE REPLY21AC202AP15 CQLRJ /D/ 10CONTENT IN PERCENT,ALCOHOL ALCOHOL CONTENT IN PERCENT THE VOLUME OF ALCOHOL AT 15.56 DEGREES CELSIUS,EXPRESSED IN PERCENT. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1D AND 1B MODE REPLY11AC20 CQLSD 19FORM,CONTENT,CAPSULE CAPSULE CONTENT FORM THE FORM OF THE DRUG ENCAPSULATED. SELECT REPLY CODE 10AE98 CQLTJ 13THREAD SIZE,NOMINAL,MOUNTING HOLE MOUNTING HOLE NOMINAL THREAD SIZE A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE MOUNTING HOLE THREAD. 1D AND 1B MODE REPLY11AA05 CQLWJ /D/ 10PRESSURE RATING AND PUMP DESIGNATION,DISCHARGE DISCHARGE PRESSURE RATING AND PUMP DESIGNATION THE DISCHARGE PRESSURE FOR WHICH AN ITEM IS RATED,AND THE PUMP DESIGNATION. 2D AND 1B MODE REPLY22AG203AA96 CQLXD 19CHARACTERISTIC,ABSORBING,HEAT HEAT ABSORBING CHARACTERISTIC THE ABILITY OF THE ITEM TO INTERCEPT APPRECIABLE PORTIONS OF RADIANT ENERGY (ESPECIALLY SOLAR ENERGY) BY VIRTUE OF ITS LIGHT TRANSMISSION CHARACTERISTICS. SELECT REPLY CODE 10AA06 CQLYJ 04DISTANCE BETWEEN CENTERLINES OF COVER PLATE MOUNTING FACILITIES PARALLEL TO LENGTH DISTANCE BETWEEN CENTERLINES OF COVER PLATE MOUNTING FACILITIES PARALLEL TO LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQLZJ 10COEFFICIENT OF CAPACITANCE PER SECTION IN PPM PER DEG CELSIUS,TEMP TEMP COEFFICIENT OF CAPACITANCE PER SECTION IN PPM PER DEG CELSIUS THE CONSTANT THAT REPRESENTS THE PROPORTIONATE CHANGE IN CAPACITANCE PER SECTION CAUSED BY A CHANGE IN TEMPERATURE,EXPRESSED IN PARTS PER MILLION PER DEGREE CELSIUS. 1D AND 1B MODE REPLY12AH19 CQMBJ /D/ 04DIAMETER,ELEMENT,ROLLING,PIVOT PIVOT ROLLING ELEMENT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQMCA /D/ 19SIZE FOR WHICH DESIGNED,BATTERY BATTERY SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE BATTERY/IES/ FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 CQMDJ 04WIDTH,HOLE,ACCOMMODATION ACCOMMODATION HOLE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQMFG 04SIZE SIZE A MEASUREMENT OF THE ITEMS LENGTH,WIDTH,HEIGHT,AND THE LIKE. FULL TEXT WRITE-IN 0 CQMGD 08LOCATION,GLAZE GLAZE LOCATION INDICATES THE LOCATION OF THE GLAZE ON THE ITEM. SELECT REPLY CODE 10AN73 CQMHJ 04WIDTH,HOLE,WIRE WIRE HOLE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQMJA 19NUMBER,GAGE,DRUM MATERIAL DRUM MATERIAL GAGE NUMBER THE STANDARD DESIGNATION USED TO INDICATE THE THICKNESS OF THE DRUM MATERIAL. 1A MODE REPLY 0 CQMKB 10VOLTAGE RATING IN VOLTS,CONTACT CONTACT VOLTAGE RATING IN VOLTS THE VOLTAGE FOR WHICH THE CONTACTS ARE RATED,EXPRESSED IN VOLTS. 1B MODE REPLY 0 CQMLJ 04HEIGHT,RECEPTACLE,POSITIVE LOCK POSITIVE LOCK RECEPTACLE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CQMMD 13THREAD SERIES DESIGNATOR,END,FIRST FIRST END THREAD SERIES DESIGNATOR A DESIGNATOR DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CQMNJ /D/ 04DISTANCE,OUTER EDGE TO BODY SLOT OUTER EDGE TO BODY SLOT DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CQMPD 18TYPE,SOLUTION,PRESERVATIVE PRESERVATIVE SOLUTION TYPE INDICATES THE TYPE OF SOLUTION USED TO PRESERVE THE ITEM. SELECT REPLY CODE 10AK89 CQMQJ 04DISTANCE,LEG END TO PLANE OF BEND LEG END TO PLANE OF BEND DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CQMRJ /D/ 10FREQUENCY RATING PER POWER SOURCE,AC AC FREQUENCY RATING PER POWER SOURCE THE NUMBER OF COMPLETE AC CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE POWER SOURCE/S/ OF THE ITEM IS RATED. 3D AND 1B MODE REPLY31AE061AC202AP27 CQMTJ 04THICKNESS,KEY,SECOND SECOND KEY THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CQMWH /D/ 19PROTECTION AND DESIGNATION,ENVIRONMENTAL,PRIME MOVER PRIME MOVER ENVIRONMENTAL PROTECTION AND DESIGNATION THE PROTECTION FROM ENVIRONMENTAL ELEMENTS,OR CONDITIONS THAT THE PRIME MOVER CAN WITHSTAND,AND ITS DESIGNATION. 2D MODE REPLY 23AJ951AP23 CQMXJ /D/A18TYPE AND QUANTITY,DEVICE,SECURING SECURING DEVICE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF MECHANICAL DEVICES PROVIDED FOR SECURING THE ITEM. 1D AND 1A MODE REPLY12AC52 CQMYJ /D/ 10PRESSURE AND DESIGNATION,STEAM,EXHAUST,PRIME MOVER PRIME MOVER EXHAUST STEAM PRESSURE AND DESIGNATION THE PRESSURE OF THE EXPANDED STEAM AFTER DRIVING A PRIME MOVER,AND ITS DESIGNATION. 2D AND 1B MODE REPLY22AG201AP23 CQMZB /D/ 04TAPER PER FOOT IN INCHES,RING,INNER INNER RING TAPER PER FOOT IN INCHES NONE. 1B MODE REPLY 0 CQNBJ /D/ 04LENGTH,TERMINAL,FIRST END FIRST END TERMINAL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQNCJ /D/ 04DIAMETER AND POSITION,OVERALL,LENS LENS OVERALL DIAMETER AND POSITION NONE. 3D AND 1B MODE REPLY31AA051AC202AK17 CQNDJ /D/ 10CURRENT RATING AND TYPE PER POLE,MAXIMUM,CONTINUOUS LOAD CONTINUOUS LOAD MAXIMUM CURRENT RATING AND TYPE PER POLE THE MAXIMUM CURRENT LOAD AND TYPE THAT EACH POLE IS RATED TO CARRY CONTINUOUSLY. 3D AND 1B MODE REPLY32AN862AN872AP31 CQNFJ /D/T13THREAD PITCH DIAMETER,INTERNAL,HEAD HEAD INTERNAL THREAD PITCH DIAMETER THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF THE HEAD INTERNAL STRAIGHT SCREW THREADS. 1D AND 1F MODE REPLY11AA05 CQNGJ 04DIAMETER,OUTSIDE,DISCHARGE CONNECTION FLANGE DISCHARGE CONNECTION FLANGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQNHJ /D/A13THREAD CLASS AND SEQUENCE DESIGNATION,MOUNTING MOUNTING THREAD CLASS AND SEQUENCE DESIGNATION A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE OF AN EXTERNAL OR INTERNAL THREAD AND THE MOUNTING SEQUENCE. 1D AND 1A MODE REPLY12AP26 CQNJB /D/ 08LOCATION IN TURNS,TAP TAP LOCATION IN TURNS THE NUMBER OF WIRE TURNS AT WHICH THE TAP/S/ IS LOCATED FROM AN END TERMINAL ON A WINDING. 1B MODE REPLY 0 CQNKA /D/ 12QUANTITY,SWITCH,CAM ACTUATED CAM ACTUATED SWITCH QUANTITY THE NUMBER OF SWITCHES ON THE CAM ACTUATED ITEM. 1A MODE REPLY 0 CQNLJ /D/ 04DIAMETER AND TYPE,HOLE HOLE DIAMETER AND TYPE THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE,AND THE TYPE OF HOLE. 3D AND 1B MODE REPLY31AA051AC202AH37 CQNMD 14SHAPE,FLANGE,COUPLING COUPLING FLANGE SHAPE THE PHYSICAL CONFIGURATION OF THE COUPLING FLANGE. SELECT REPLY CODE 10AP00 CQNNJ 04LENGTH,BODY,STUD STUD BODY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQNPJ /D/ 04DIAMETER,SHANK,FASTENER FASTENER SHANK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQNQJ /D/ 04DIAMETER,INSIDE,SHAFT SHAFT INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQNRD 01COLOR,GLASS GLASS COLOR THE HUE OR TINT OF THE GLASS. SELECT REPLY CODE 10AD06 CQNSJ A18TYPE AND QUANTITY,CUT CUT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF CUTS PROVIDED. 1D AND 1A MODE REPLY13AK95 CQNTJ /D/ 04HEIGHT,SEAT,RING RING SEAT HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CQNWJ /D/ 04WIDTH,FLANGE,RING RING FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQNXJ 04THICKNESS,BEAM BEAM THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CQNYJ 04ANGLE IN DEG AND LOCATION,HOLE,COUNTERSUNK COUNTERSUNK HOLE ANGLE IN DEG AND LOCATION THE COUNTERSUNK HOLE ANGLE,EXPRESSED IN DEGREES,AND THE LOCATION. 1D AND 1B MODE REPLY13AN73 CQNZJ /D/ 04WIDTH AND SEQUENCE DESIGNATION,SLOT,MOUNTING MOUNTING SLOT WIDTH AND SEQUENCE DESIGNATION NONE. 3D AND 1B MODE REPLY31AA051AC202AP26 CQPBJ 10TIME IN SECONDS,DELAY,INTERRUPTION,CIRCUIT OVER-CURRENT CIRCUIT OVER-CURRENT INTERRUPTION DELAY TIME IN SECONDS THE TIME ELAPSING BEFORE CIRCUIT INTERRUPTION OF AN ITEM OPERATED AT A SPECIFIED PERCENT OF ITS NORMAL CURRENT RATING,EXPRESSED IN SECONDS. 1D AND 1B MODE REPLY12AP37 CQPCJ /D/ 04WIDTH ACROSS FLATTED PORTION WIDTH ACROSS FLATTED PORTION NONE. 2D AND 1B MODE REPLY21AA051AC20 CQPDJ /D/ 04DIAMETER,RECESS,LOCKING LOCKING RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQPFB /D/ 04TAPER PER FOOT IN INCHES,RING,OUTER OUTER RING TAPER PER FOOT IN INCHES NONE. 1B MODE REPLY 0 CQPGH /D/ 18TYPE AND PUMP DESIGNATION,IMPELLER IMPELLER TYPE AND PUMP DESIGNATION INDICATES THE TYPE OF IMPELLER INCLUDED ON THE ITEM,AND THE PUMP DESIGNATION. 2D MODE REPLY 21AF093AA96 CQPHD 18TYPE,DESIGN,DEVICE DEVICE DESIGN TYPE INDICATES THE DESIGN TYPE OF THE DEVICE. SELECT REPLY CODE 10AL58 CQPJJ 04ANGLE,CHAMFER,PIN PIN CHAMFER ANGLE NONE. REPLACED BY MRC CSYT WITH ISAC 0368. 2D AND 1B MODE REPLY21AP381AC20 CQPKJ /D/ 10VOLTAGE RATING AND TYPE PER POLE IN VOLTS,OPERATING OPERATING VOLTAGE RATING AND TYPE PER POLE IN VOLTS THE VOLTAGE AND CURRENT TYPE FOR WHICH EACH POLE IS RATED TO OPERATE,EXPRESSED IN VOLTS. 2D AND 1B MODE REPLY22AN872AP31 CQPLD /D/ 03DESIGNATOR,SIZE,LAMP BULB LAMP BULB SIZE DESIGNATOR THE DESIGNATION THAT DESCRIBES THE SIZE AND CONFIGURATION OF A LAMP BULB. SELECT REPLY CODE 10AP17 CQPMH /D/ 09MATERIAL AND LOCATION,COVERING COVERING MATERIAL AND LOCATION THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE COVERING IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT,AND THE LOCATION. 2D MODE REPLY 23AN736AD09 CQPNJ 04DISTANCE FROM HOOK CENTER TO NEAREST OUTSIDE EDGE ALONG LENGTH DISTANCE FROM HOOK CENTER TO NEAREST OUTSIDE EDGE ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQPPJ /D/ 04DISTANCE FROM DOME HOLE CENTER TO DESIGNATED POINT DISTANCE FROM DOME HOLE CENTER TO DESIGNATED POINT NONE. 2D AND 1B MODE REPLY21AA051AC20 CQPQG 19STATEMENTS,WARNING AND CAUTION WARNING AND CAUTION STATEMENTS THE STATEMENTS REQUIRED TO BE INCLUDED ON THE LABEL OF DRUGS SUBJECT TO PROVISIONS OF THE FEDERAL FOOD,DRUG,AND COSMETIC ACT. FULL TEXT WRITE-IN 0 CQPRJ /D/ 04ANGLE,SEAT,FIRST END FIRST END SEAT ANGLE THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS. 2D AND 1B MODE REPLY21AP381AC20 CQPSD 08LOCATION,REINFORCEMENT REINFORCEMENT LOCATION INDICATES THE LOCATION OF THE REINFORCEMENT ON THE ITEM. SELECT REPLY CODE 10AN73 CQPTD /D/ 19SECTION ACTUATED,SWITCH SWITCH SECTION ACTUATED INDICATES THE SECTION OF THE SWITCH THAT IS ACTUATED. SELECT REPLY CODE 10AD76 CQPWJ 04ANGLE,DIFFERENTIAL,SWITCH ACTUATION SWITCH ACTUATION DIFFERENTIAL ANGLE THE AMOUNT OF SWITCH MOVEMENT REQUIRED TO EFFECT THE SWITCHING ACTION. 2D AND 1B MODE REPLY21AP381AC20 CQPXJ 10UNIT,GRADUATION,SCALE SCALE GRADUATION UNIT INDICATES THE INCREMENTS OF MEASURE ON THE SCALE. 1D AND 1B MODE REPLY12AG67 CQPYJ 04ANGLE,BEVEL BEVEL ANGLE THE ANGLE OF THE BEVEL. 2D AND 1B MODE REPLY21AP381AC20 CQPZJ 04SIZE,CONDUCTOR,WINDING WINDING CONDUCTOR SIZE THE SIZE OF THE CONDUCTOR WHICH FORMS THE WINDING ON THE ITEM. 2D AND 1B MODE REPLY21AA051AB96 CQQBJ 04LENGTH,END,TAPERED TAPERED END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQQCD 19CYCLE,DUTY,TRIP RELEASE TRIP RELEASE DUTY CYCLE THE WORKING PERIOD WHICH THE TRIP RELEASE IS DESIGNED TO OPERATE. SELECT REPLY CODE 10AD63 CQQDD 18TYPE,HOOD HOOD TYPE INDICATES THE TYPE OF HOOD INCLUDED ON THE ITEM. SELECT REPLY CODE 10AP40 CQQFJ 10PRESSURE,OPERATING OPERATING PRESSURE THE PRESSURE AT WHICH AN ITEM IS DESIGNED TO OPERATE. 2D AND 1B MODE REPLY22AG671AC20 CQQGH /D/ 11METHOD AND DESIGNATION,COOLING,PRIME MOVER PRIME MOVER COOLING METHOD AND DESIGNATION THE MEANS OF COOLING USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE PRIME MOVER AND ITS DESIGNATION. 2D MODE REPLY 23AN051AP23 CQQHJ 04DIAMETER,NOMINAL,CORE CORE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CORE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CQQJJ 04LENGTH,TIP,SEAL-OFF SEAL-OFF TIP LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQQKJ 04WIDTH,HOLE,PANEL ACCOMMODATION PANEL ACCOMMODATION HOLE WIDTH THE WIDTH OF THE PANEL OPENING FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 CQQLH 02DESIGN,TIRE TIRE DESIGN THE TIRE DESIGN AND THE TYPE OF BASE MOUNTING FACILITY. 2D MODE REPLY 21AN832AN84 CQQMJ /D/ 04WIDTH,RING,INNER,ROD END ROD END INNER RING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQQNH /D/ 18TYPE AND LOCATION,PROTECTION,EXTERNAL EXTERNAL PROTECTION TYPE AND LOCATION INDICATES THE TYPE OF EXTERNAL PROTECTION PROVIDED AND ITS LOCATION ON THE ITEM. 2D MODE REPLY 23AN732AF34 CQQPJ 04HEIGHT,OVERALL,TURNBUTTON TURNBUTTON OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CQQQH /D/ 01COLOR AND LOCATION COLOR AND LOCATION A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY,AND ITS LOCATION ON THE ITEM. 2D MODE REPLY 23AN736AD06 CQQRB 13THREAD PITCH IN MILLIMETERS THREAD PITCH IN MILLIMETERS A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CQQSJ A12QUANTITY,MESH MESH QUANTITY THE NUMBER OF MESH PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY11AB39 CQQTD 19POSITION,MOMENTARY,SWITCH ACTUATOR SWITCH ACTUATOR MOMENTARY POSITION THE POSITION OF THE ACTUATOR,WITH RELATION TO THE EXTREMITY OF ROTATION,THAT IS MOMENTARY (SPRING LOADED). SELECT REPLY CODE 10AC84 CQQWJ 04DIAMETER,INSIDE,SOCKET SOCKET INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQQXJ /D/ 04LENGTH,MAJOR,BUSHING BUSHING MAJOR LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQQYD /D/ 07ADJUSTABILITY,DIFFERENTIAL,ACTUATING,CONTACT CONTACT ACTUATING DIFFERENTIAL ADJUSTABILITY AN INDICATION OF WHETHER THE DIFFERENCE BETWEEN THE POINTS AT WHICH THE CONTACTS ACTUATE AND DEACTUATE IS ADJUSTABLE. SELECT REPLY CODE 10AC06 CQQZD /D/ 11METHOD,ATTACHMENT,LIGHTING CONDUCTOR LIGHTING CONDUCTOR ATTACHMENT METHOD THE MEANS OF ATTACHING THE LIGHTING CONDUCTORS TO THE ITEM. SELECT REPLY CODE 10AM39 CQRBJ 04ANGLE,SEAT SEAT ANGLE THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS. 1D AND 1B MODE REPLY11AP38 CQRCH /D/ 18TYPE AND PUMP DESIGNATION,ACTION,RECIPROCATING RECIPROCATING ACTION TYPE AND PUMP DESIGNATION INDICATES THE TYPE OF PUMPING ACTION PRODUCED BY THE ITEM,AND THE PUMP DESIGNATION. 2D MODE REPLY 21AF093AA96 CQRDA 12QUANTITY,RESISTOR,IDENTICAL VALUE IDENTICAL VALUE RESISTOR QUANTITY THE NUMBER OF RESISTORS OR RESISTOR ELEMENTS HAVING THE SAME RESISTANCE VALUE. 1A MODE REPLY 0 CQRFJ /D/ 04DIAMETER,MINOR,PLUG PLUG MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQRGD 09MATERIAL,BODY BODY MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE BODY IS FABRICATED. SELECT REPLY CODE 10MA01 CQRHJ A03DESIGNATOR,APPROVAL APPROVAL DESIGNATOR THE DESIGNATION WHICH IDENTIFIES THE REQUIRED APPROVAL OF THE ITEM. 1D AND 1A MODE REPLY11AP41 CQRJJ 04DIAMETER,OUTSIDE,NOMINAL TUBE NOMINAL TUBE OUTSIDE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CQRKD 19CAPABILITY,LOAD LOAD CAPABILITY THE LOAD WHICH THE ITEM IS CAPABLE OF HOLDING. SELECT REPLY CODE 10AJ87 CQRLJ /D/ 10OUTPUT AND FUNCTION,POWER POWER OUTPUT AND FUNCTION THE AMOUNT OF ELECTRICAL POWER THE ITEM IS CAPABLE OF PRODUCING AND ITS FUNCTION. 3D AND 1B MODE REPLY32AN861AC202AK27 CQRMJ 04DEPTH,HOLE,SHANK,STUD STUD SHANK HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQRNJ A13THREAD QUANTITY THREAD QUANTITY THE NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY11AB39 CQRPH /D/ 19PROVISION AND SEQUENCE DESIGNATION,MOUNTING MOUNTING PROVISION AND SEQUENCE DESIGNATION THE MEANS BY WHICH THE ITEM IS DESIGNED TO BE ATTACHED AND THE SEQUENCE DESIGNATION. 2D MODE REPLY 23AM392AP26 CQRQJ 08LOCATION,ANGULAR,SHAFT FLAT/SLOT SHAFT FLAT/SLOT ANGULAR LOCATION THE ANGULAR DISTANCE OF THE SHAFT FLAT OR SLOT FROM THE POINT OF REFERENCE. 2D AND 1B MODE REPLY21AP381AD94 CQRRJ 10TAPER TAPER THE AMOUNT OF TAPER MEASURED PARALLEL TO THE LONGITUDINAL AXIS OF THE ITEM PER SPECIFIC MEASUREMENT SCALE. 1D AND 1B MODE REPLY11AB39 CQRSJ /D/ 04DIAMETER,INSIDE,REDUCED PASSAGE REDUCED PASSAGE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE REDUCED PASSAGE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CQRTJ /D/ 04DISTANCE BETWEEN THIRD AND FOURTH TURRET DISTANCE BETWEEN THIRD AND FOURTH TURRET NONE. 2D AND 1B MODE REPLY21AA051AC20 CQRWB 10OUTPUT IN GALLONS PER MINUTE,WATER,MAXIMUM MAXIMUM WATER OUTPUT IN GALLONS PER MINUTE THE MAXIMUM DELIVERY OF WATER,EXPRESSED IN GALLONS PER MINUTE. 1B MODE REPLY 0 CQRXJ /D/ 04ANGLE,SEAT,FOURTH END FOURTH END SEAT ANGLE THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS. 2D AND 1B MODE REPLY21AP381AC20 CQRYH 14SHAPE AND LOCATION,DRIVE,SCREW PLUG SCREW PLUG DRIVE SHAPE AND LOCATION THE PHYSICAL CONFIGURATION OF THE SCREW PLUG DRIVE AND ITS LOCATION ON THE ITEM. 2D MODE REPLY 23AP003AN73 CQRZD /D/ 07CARD,RECORD RECORD CARD AN INDICATION OF WHETHER OR NOT A RECORD CARD IS INCLUDED. SELECT REPLY CODE 10AA49 CQSBL 16STYLE,CAP CAP STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CAP. 1L MODE REPLY 0 CQSCD 17SURFACE TREATMENT,HOLDER HOLDER SURFACE TREATMENT THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE HOLDER IS PLATED,DIPPED AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF. SELECT REPLY CODE 10SF01 CQSDJ 10LIFT RATING,MAGNET MAGNET LIFT RATING THE MAGNET LIFT RATING AS INDICATED BY THE WEIGHT THAT THE MAGNET WILL RETAIN. 1D AND 1B MODE REPLY12AN75 CQSFJ 04LENGTH,STUD,CENTER CENTER STUD LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQSGD 19PURPOSE,KNOB KNOB PURPOSE THE PURPOSE FOR WHICH THE KNOB IS INTENDED. SELECT REPLY CODE 10AJ41 CQSHJ 10SPACING,HOLE,FIRST FIRST HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 CQSJD 09MATERIAL,INCLOSURE INCLOSURE MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE INCLOSURE IS FABRICATED. SELECT REPLY CODE 10MA01 CQSKJ 04DIAMETER,BODY,STUD STUD BODY DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQSLJ /D/ 04DIAMETER ACCOMMODATED,DISH DISH DIAMETER ACCOMMODATED NONE. 2D AND 1B MODE REPLY21AA051AC20 CQSMH 08LOCATION AND POSITION DESIGNATION,SWITCH SWITCH LOCATION AND POSITION DESIGNATION INDICATES THE LOCATION OF THE SWITCH IN RELATION TO ITS DESIGNATED POSITION. 2D MODE REPLY 23AN733AJ50 CQSNJ /D/ 04DIAMETER,PIN,DOWEL DOWEL PIN DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQSPJ 04SIZE ACCOMMODATED,FITTING,NOMINAL NOMINAL FITTING SIZE ACCOMMODATED A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE FITTING SIZE ACCOMMODATED. 1D AND 1B MODE REPLY11AA05 CQSQJ 04ANGLE,OUTSIDE OUTSIDE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CQSRJ 04LENGTH,OVERALL,PLATE PLATE OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE PLATE. 2D AND 1B MODE REPLY21AA051AC20 CQSSJ /D/ 04DIAMETER,OUTSIDE,LARGEST,CUP CUP LARGEST OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQSTJ 04DIAMETER FOR WHICH DESIGNED,NECK,FILLER FILLER NECK DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FILLER NECK FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 CQSWD /D/ 07ADJUSTABILITY,STRAP,THIGH THIGH STRAP ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE THIGH STRAP IS ADJUSTABLE. SELECT REPLY CODE 10AB00 CQSXJ A10STRENGTH,SHEAR SHEAR STRENGTH THE MINIMUM LOAD,APPLIED PERPENDICULARLY TO THE LONGITUDINAL AXIS OF AN ITEM,AT WHICH POINT THE ITEM WILL FRACTURE WHEN SUBJECTED TO THE STANDARD SHEAR TEST METHOD. 2D AND 1A MODE REPLY21AF091AN71 CQSYJ 04THICKNESS,MATERIAL,RECEPTACLE RECEPTACLE MATERIAL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CQSZD 19CONFIGURATION,INCLOSURE INCLOSURE CONFIGURATION INDICATES THE PHYSICAL CONFIGURATION OF THE INCLOSURE. SELECT REPLY CODE 10AG85 CQTBA 12QUANTITY,MEMORY MEMORY QUANTITY THE NUMBER OF MEMORIES INCLUDED IN THE ITEM. 1A MODE REPLY 0 CQTCJ 04LENGTH,INSIDE,THIMBLE THIMBLE INSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQTDB /D/ 04TAPER PER METER IN MILLIMETERS,ROLLER ROLLER TAPER PER METER IN MILLIMETERS NONE. 1B MODE REPLY 0 CQTFA 12QUANTITY,UNIT,PRIMARY CONTAINER PRIMARY CONTAINER UNIT QUANTITY THE NUMBER OF ITEMS OF SUPPLY WITHIN EACH PRIMARY CONTAINER. 1A MODE REPLY 0 CQTGA 12QUANTITY,BALL BALL QUANTITY THE NUMBER OF BALLS INCLUDED ON THE ITEM. 1A MODE REPLY 0 CQTHA 12QUANTITY,ROTOR THROUGH CONNECTION ROTOR THROUGH CONNECTION QUANTITY INDICATES THE NUMBER OF CONNECTIONS ON A ROTOR SEGMENT THAT ARE FRONT TO REAR SURFACE CONNECTED. 1A MODE REPLY 0 CQTJH /D/ 19PHASE AND DESIGNATION,PRIME MOVER PRIME MOVER PHASE AND DESIGNATION THE NUMBER OF ALTERNATING CURRENT PHASES OF THE PRIME MOVER,AND ITS DESIGNATION. 2D MODE REPLY 21AD021AP23 CQTKD 19ARRANGEMENT,PLY,TIRE TIRE PLY ARRANGEMENT THE ANGLE AT WHICH THE PLIES ARE LAID IN RELATIONSHIP TO THE CIRCUMFERENTIAL CENTERLINE OF THE TIRE. SELECT REPLY CODE 10AA28 CQTLJ 10VOLTAGE RATING AND TYPE IN VOLTS,RESET ACTUATOR RESET ACTUATOR VOLTAGE RATING AND TYPE IN VOLTS THE VOLTAGE,EXPRESSED IN VOLTS,AND CURRENT TYPE FOR WHICH THE RESET ACTUATOR IS RATED. 1D AND 1B MODE REPLY12AN87 CQTMD 08LOCATION,TERMINAL TERMINAL LOCATION INDICATES THE LOCATION OF THE TERMINAL/S/ ON THE ITEM. SELECT REPLY CODE 10AN73 CQTNJ A18TYPE AND QUANTITY,JEWEL JEWEL TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF JEWELS PROVIDED. 1D AND 1A MODE REPLY16MA01 CQTPJ A13SCREW THREAD QUANTITY PER INCH AND LOCATION SCREW THREAD QUANTITY PER INCH AND LOCATION THE NUMBER OF SCREW THREADS ON THE ITEM PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS AND THE THREAD LOCATION. 1D AND 1A MODE REPLY13AN73 CQTQJ A18TYPE AND QUANTITY,DEVICE,ADJUSTMENT ADJUSTMENT DEVICE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF FACILITIES FOR ADJUSTING THE ITEM. 1D AND 1A MODE REPLY13AE10 CQTRJ 04DIAMETER,SHANK,SECOND SECOND SHANK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQTSB 04SIZE ACCOMMODATED,TRADE,CONDUIT CONDUIT TRADE SIZE ACCOMMODATED INDICATES THE INDUSTRIAL SIZE DESIGNATION OF THE CONDUIT WHICH THE ITEM WILL ACCOMMODATE. 1B MODE REPLY 0 CQTTD /D/ 09MATERIAL,BASE,TARGET TARGET BASE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TARGET BASE IS FABRICATED. SELECT REPLY CODE 10AD09 CQTWA 13THREAD QUANTITY PER INCH,HOLE HOLE THREAD QUANTITY PER INCH THE NUMBER OF HOLE THREADS PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CQTXD 18TYPE,END,TERMINAL TERMINAL END TYPE INDICATES THE TYPE OF TERMINAL END PROVIDED. SELECT REPLY CODE 10AF95 CQTYJ 10CONSUMPTION RATE PER HOUR,FUEL FUEL CONSUMPTION RATE PER HOUR THE AMOUNT OF FUEL THE ITEM IS RATED TO CONSUME PER HOUR. 1D AND 1B MODE REPLY12AG67 CQTZD 09MATERIAL,CONTACT CONTACT MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE CONTACT IS FABRICATED. SELECT REPLY CODE 10MA01 CQWBD 19APPLICATION,INTERLEAVING,PAPER PAPER INTERLEAVING APPLICATION INDICATES THE PAPER INTERLEAVING AS APPLIED TO THE ITEM. SELECT REPLY CODE 10AP51 CQWCJ 04HEIGHT,STEP,SECOND SECOND STEP HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CQWDJ 10RESISTANCE,POWER,ZERO ZERO POWER RESISTANCE THE DC RESISTANCE VALUE MEASURED WITH A POWER DISSIPATION LOW ENOUGH THAT ANY FURTHER DECREASE IN POWER WILL RESULT IN NOT MORE THAN 0.1 PERCENT CHANGE IN RESISTANCE. 1D AND 1B MODE REPLY12AN86 CQWFH /D/ 18TYPE-LOCATION AND PUMP DESIGNATION,CONTROL,VOLUME VOLUME CONTROL TYPE-LOCATION AND PUMP DESIGNATION INDICATES THE TYPE AND LOCATION OF THE DEVICE USED TO CONTROL THE OUTPUT OR CAPACITY OF AN ITEM AND THE PUMP DESIGNATION. 3D MODE REPLY 32AH833AN733AA96 CQWGJ 10LOAD RATING,VERTICAL VERTICAL LOAD RATING THE VERTICAL PULL FOR WHICH THE ITEM IS RATED,PER SPECIFIC MEASUREMENT SCALE. 1D AND 1B MODE REPLY12AN75 CQWHB 04ANGLE IN DEG,TARGET TARGET ANGLE IN DEG THE ANGLE OF THE TARGET IN RELATION TO THE PATH OF ELECTRON FLOW,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CQWJA 03DESIGNATOR,IDENTIFICATION,AWARD AWARD IDENTIFICATION DESIGNATOR A NUMERIC/ALPHA DESIGNATION WHICH IDENTIFIES AN ORGANIZATION,ELEMENT,RECEIPT OF AN AWARD,OR THE LIKE. 1A MODE REPLY 0 CQWKJ /D/ 04DEPTH,COUNTERBORE,GEAR GEAR COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQWLA /D/ 13THREAD CLASS,BULKHEAD BULKHEAD THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE OF AN EXTERNAL OR INTERNAL THREAD ON THE BULKHEAD. 1A MODE REPLY 0 CQWMJ 10VOLTAGE RATING AND TYPE PER SECTION,CONTINUOUS,NONDERATED NONDERATED CONTINUOUS VOLTAGE RATING AND TYPE PER SECTION THE HIGHEST VALUE AND TYPE OF POTENTIAL THAT MAY BE CONTINUOUSLY APPLIED TO THE ITEM PER SECTION AT THE HIGHEST OPERATING TEMPERATURE PERMISSIBLE WITHOUT VOLTAGE DERATING. 2D AND 1B MODE REPLY22AN872AH19 CQWNJ 10TIME IN SECONDS PER RATED CONTINUOUS CURRENT,DELAY,TRIP TRIP DELAY TIME IN SECONDS PER RATED CONTINUOUS CURRENT THE LENGTH OF TIME,EXPRESSED IN SECONDS,THAT AN OVERLOAD MAY EXIST BEFORE THE DEVICE WILL TRIP AT A SPECIFIED CONTINUOUS CURRENT. 2D AND 1B MODE REPLY21AC202AP32 CQWPA 19NUMBER,MOULDING,WOOD PRODUCER WOOD PRODUCERS MOULDING NUMBER THE WOOD PRODUCERS NUMERIC DESIGNATION WHICH IDENTIFIES THE WIDTH AND THICKNESS OF THE MOULDING. 1A MODE REPLY 0 CQWQJ 13THREAD LENGTH,SHAFT SHAFT THREAD LENGTH A MEASUREMENT OF THE EXTENT OF THE SHAFT THREADS MEASURED ON A LINE PARALLEL TO THE LONGITUDINAL AXIS. 2D AND 1B MODE REPLY21AA051AC20 CQWRA 13THREAD TOLERANCE CLASS,EXTERNAL EXTERNAL THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITIONS AND GRADES OF AN EXTERNAL THREAD. 1A MODE REPLY 0 CQWSJ 04DEPTH,KEYWAY,WASHER WASHER KEYWAY DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQWTH 10INTENSITY,LIGHT LIGHT INTENSITY THE INTENSITY OF LIGHT MEASURED AT A GIVEN DISTANCE FROM THE SOURCE,AND THE FIELD OF LIGHT PROJECTION. 3D MODE REPLY 31AE211AE201AE22 CQWWJ /D/A19DOCUMENT AND CLASSIFICATION,SURFACE TREATMENT,BODY BODY SURFACE TREATMENT DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE BODY SURFACE TREATMENT MATERIAL. 2D AND 1A MODE REPLY21AP331AP39 CQWXD 19FORM,LOGIC,OUTPUT OUTPUT LOGIC FORM AN INDICATION OF THE BASIC ELECTRONIC CIRCUIT ELEMENTS ASSEMBLED TO OUTPUT A LOGIC FUNCTION. SELECT REPLY CODE 10AP42 CQWYH 19SPECIES-GRADE AND GRADING ASSOCIATION SPECIES-GRADE AND GRADING ASSOCIATION AN INDICATION OF THE SPECIES AND GRADE OF THE ITEM,AND THE GRADING ASSOCIATION. 3D MODE REPLY 32AM002AP022AP03 CQWZJ /D/ 04LENGTH,CHAMFER,FIRST INSIDE CORNER FIRST INSIDE CORNER CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 CQXBJ /D/ 04DISTANCE BETWEEN DOWEL PIN AND MOUNTING FACILITY,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN DOWEL PIN AND MOUNTING FACILITY NONE. 2D AND 1B MODE REPLY21AA051AC20 CQXCD 08LOCATION,HUB HUB LOCATION INDICATES THE LOCATION OF THE HUB ON THE ITEM. SELECT REPLY CODE 10AN73 CQXDJ 10DELIVERY RATE,HEAT HEAT DELIVERY RATE THE RATE OF HEAT DELIVERY OF THE ITEM. 1D AND 1B MODE REPLY11AP36 CQXFD 18TYPE FOR WHICH DESIGNED,PROTECTION,INCLOSURE INCLOSURE PROTECTION TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF PROTECTION FOR WHICH THE INCLOSURE IS DESIGNED. SELECT REPLY CODE 10AP30 CQXGJ 04HEIGHT,LIP LIP HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CQXHJ /D/ 10HEAD RATING AND PUMP DESIGNATION,TOTAL TOTAL HEAD RATING AND PUMP DESIGNATION THE SUM OF THE TOTAL DISCHARGE HEAD AND SUCTION LIFT FOR WHICH AN ITEM IS RATED,AND THE PUMP DESIGNATION. 2D AND 1B MODE REPLY21AA053AA96 CQXJB /D/ 04ANGLE IN DEG,CHAMFER,FIRST INSIDE CORNER FIRST INSIDE CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 CQXKJ 04DIAMETER,INSIDE,FERRULE FERRULE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CQXLJ 04ANGLE,BEVEL,FACE FACE BEVEL ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CQXMJ /D/ 13THREAD LENGTH,HOLE,CONCENTRIC CONCENTRIC HOLE THREAD LENGTH A MEASUREMENT OF THE EXTENT OF THE CONCENTRIC HOLE THREADS MEASURED ON A LINE PARALLEL TO THE LONGITUDINAL AXIS. 2D AND 1B MODE REPLY21AA051AC20 CQXNJ /D/X19CODE AND IDENTIFYING NUMBER,MANUFACTURER,ACCESSORY ACCESSORY MANUFACTURER CODE AND IDENTIFYING NUMBER THE FIVE DIGIT CODE WHICH REPRESENTS THE MANUFACTURER OF THE ACCESSORY FURNISHED AND THE IDENTIFYING NUMBER. 1D AND 1A MODE REPLY15AN63 CQXPJ 04WIDTH,EYELET EYELET WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQXQJ 10REACTANCE IN OHMS,ZRO,PLUS J PLUS J ZRO REACTANCE IN OHMS THE REACTANCE (X) PART OF THE ROTOR IMPEDANCE WITH THE STATOR OPEN (ZRO). 1D AND 1B MODE REPLY11AC20 CQXRJ /D/ 04LENGTH,CHAMFER,THIRD OUTSIDE CORNER THIRD OUTSIDE CORNER CHAMFER LENGTH NONE. REPLACED BY MRC AAZP WITH ISAC 0368. 2D AND 1B MODE REPLY21AA051AC20 CQXSJ 04ANGLE,COUNTERSINK,SECOND END SECOND END COUNTERSINK ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CQXTJ /D/ 04ANGLE,SEAT,INLET INLET SEAT ANGLE THE ANGLE OF THE INLET SEAT SURFACE UPON WHICH THE MATED SURFACE SEATS. 2D AND 1B MODE REPLY21AP381AC20 CQXWD 07SECURITY,DEFENSE INFORMATION,CLASSIFIED CLASSIFIED DEFENSE INFORMATION SECURITY AN INDICATION OF WHETHER OR NOT THE ITEM IS AUTHORIZED FOR THE SECURITY OF CLASSIFIED DEFENSE INFORMATION. SELECT REPLY CODE 10AP48 CQXXJ 10VOLTAGE,OPERATING,AC,WINDING WINDING AC OPERATING VOLTAGE THE VALUE(S) OF ALTERNATING CURRENT OPERATING VOLTAGE APPLIED TO THE WINDING. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 2D AND 1B MODE REPLY21AB631AC20 CQXYJ /D/ 13THREAD SIZE AND SEQUENCE DESIGNATION,MOUNTING MOUNTING THREAD SIZE AND SEQUENCE DESIGNATION THE NOMINAL DIAMETER AND MOUNTING SEQUENCE WHICH IS USED TO IDENTIFY THE THREADED FACILITY. 2D AND 1B MODE REPLY21AA052AP26 CQXZJ 04WIDTH ACROSS FLATS,SOCKET SOCKET WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 CQYBJ /D/A13THREAD QUANTITY,FACILITY,MOUNTING MOUNTING FACILITY THREAD QUANTITY THE NUMBER OF THREADS ON THE MOUNTING FACILITY PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY11AB39 CQYCD /D/ 07PROCESSABILITY PROCESSABILITY INDICATES WHETHER THE ITEM MAY BE PROCESSED THROUGH DEVELOPING MACHINES AND SOLUTIONS WITHOUT BECOMING CONTAMINATED OR CONTAMINATING THE SOLUTION. SELECT REPLY CODE 10AP29 CQYDD /D/ 13THREAD SERIES DESIGNATOR,HOLE,CONCENTRIC CONCENTRIC HOLE THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THE THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC CONCENTRIC HOLE DIAMETER. SELECT REPLY CODE 10AH06 CQYFJ 04DISTANCE FROM SEWN SEAM TO NEAREST OUTSIDE EDGE ALONG LENGTH DISTANCE FROM SEWN SEAM TO NEAREST OUTSIDE EDGE ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQYGJ /D/ 04ANGLE,SEAT,CONE CONE SEAT ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CQYHD 17SURFACE TREATMENT,CONTACT CONTACT SURFACE TREATMENT THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE CONTACT SURFACE(S) AND CANNOT BE WIPED OFF. SELECT REPLY CODE 10SF01 CQYJD 19PATTERN,FACILITY,MOUNTING MOUNTING FACILITY PATTERN THE GENERAL CONFIGURATION AND RELATIVE POSITION OF THE FACILITIES PROVIDED FOR MOUNTING THE ITEM. SELECT REPLY CODE 10AD96 CQYKJ /D/ 10HARDNESS,TABLET TABLET HARDNESS THE COMPRESSED FORCE WHICH,WHEN APPLIED DIAMETRICALLY,FRACTURES THE TABLET. 2D AND 1B MODE REPLY22AN751AC20 CQYLJ 10LEVEL RATING,DRIVE DRIVE LEVEL RATING THE DRIVE LEVEL AT WHICH THE ITEM IS DESIGNED TO OPERATE. 2D AND 1B MODE REPLY22AN861AC20 CQYMJ 13THREAD SIZE,NOMINAL,FIRST END FIRST END NOMINAL THREAD SIZE THE DESIGNATION WHICH IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE NOMINAL THREAD SIZE. 1D AND 1B MODE REPLY11AA05 CQYNJ 04LENGTH,NECK,SHANK SHANK NECK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQYPJ /D/ 04WIDTH,CONE,INTERNAL INTERNAL CONE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQYQD 18TYPE,CLIP CLIP TYPE INDICATES THE TYPE OF CLIP PROVIDED. SELECT REPLY CODE 10AP01 CQYRJ 04SIZE,TRADE,ITEM ACCOMMODATED ITEM ACCOMMODATED TRADE SIZE THE NOMINAL SIZE THAT INDICATES THE ACTUAL INSIDE DIAMETER OF THE ITEM ACCOMMODATED. 1D AND 1B MODE REPLY11AA05 CQYSJ A19ARRANGEMENT,CONTACT,CAM ACTUATED SWITCH CAM ACTUATED SWITCH CONTACT ARRANGEMENT THE DESIGNATION INDICATING THE ELECTRICAL CONFIGURATION OF A CAM ACTUATED SWITCH INCLUDING THE NUMBER OF SWITCHING POLES OR FORMS. 1D AND 1A MODE REPLY12AG28 CQYTJ /D/ 04DISTANCE FROM END PIN HOLE CENTER TO END OF ITEM DISTANCE FROM END PIN HOLE CENTER TO END OF ITEM THE DISTANCE FROM THE END PIN HOLE CENTER TO THE NEAREST END OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CQYWH 19FUNCTION AND METHOD,OPERATING OPERATING FUNCTION AND METHOD THE FUNCTION OF AN ITEM AND THE MEANS BY WHICH IT IS OPERATED. 2D MODE REPLY 21AP253AC58 CQYXD 11METHOD,PROGRAMMING PROGRAMMING METHOD THE MEANS BY WHICH THE ITEM IS PROGRAMMED. SELECT REPLY CODE 10AC58 CQYYJ 04HEIGHT,HEAD,STUD STUD HEAD HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CQYZD /D/ 08LOCATION,HOLE HOLE LOCATION INDICATES THE LOCATION OF THE HOLE/S/ ON THE ITEM. SELECT REPLY CODE 10AN73 CQZBG /D/ 08LOCATION,VENT VENT LOCATION INDICATES THE LOCATION OF THE VENT ON THE ITEM. FULL TEXT WRITE-IN 0 CQZCD /D/ 13THREAD DIRECTION,INTERNAL,HEAD HEAD INTERNAL THREAD DIRECTION THE DIRECTION OF THE INTERNAL THREAD OF THE HEAD WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AA38 CQZDJ 04DEPTH AND LOCATION,COUNTERBORE COUNTERBORE DEPTH AND LOCATION A MEASUREMENT BETWEEN SPECIFIED POINTS OF A COUNTERBORE AND THE LOCATION. 3D AND 1B MODE REPLY31AA051AC203AN73 CQZFJ 10SPACING,ANGULAR,NUT NUT ANGULAR SPACING NONE. 2D AND 1B MODE REPLY21AP381AC20 CQZGD 09MATERIAL,INSERT INSERT MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE INSERT IS FABRICATED. SELECT REPLY CODE 10MA01 CQZHJ 04LENGTH,OVERALL,GROMMET GROMMET OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQZJJ /D/ 10VOLTAGE,OPERATING,DC,WINDING WINDING DC OPERATING VOLTAGE THE VALUE(S) OF DIRECT CURRENT OPERATING VOLTAGE APPLIED TO THE WINDING. 2D AND 1B MODE REPLY21AB631AC20 CQZKJ 04ANGLE,SECOND SECOND ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CQZLJ /D/ 04CIRCUMFERENCE AND LOCATION,NOMINAL NOMINAL CIRCUMFERENCE AND LOCATION THE NOMINAL DISTANCE AROUND THE OUTSIDE OF AN ITEM AND THE LOCATION. 2D AND 1B MODE REPLY21AA053AN73 CQZMA /D/ 13THREAD CLASS,COUNTERBORE COUNTERBORE THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE OF A COUNTERBORE THREAD. 1A MODE REPLY 0 CQZNJ 04LENGTH,LAYING,NOMINAL NOMINAL LAYING LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CQZPD 19PATTERN,CIRCUIT,INPUT INPUT CIRCUIT PATTERN THE ARRANGEMENT OR PATTERN WHICH DESCRIBES THE INPUT CIRCUITRY OF THE ITEM. SELECT REPLY CODE 10AP44 CQZQJ /D/ 10CONSUMPTION RATE AND DESIGNATION,STEAM,PRIME MOVER PRIME MOVER STEAM CONSUMPTION RATE AND DESIGNATION THE RATE AT WHICH STEAM IS CONSUMED BY A PRIME MOVER OPERATING AT FULL CAPACITY,AND ITS DESIGNATION. 2D AND 1B MODE REPLY22AJ861AP23 CQZRJ 04DISTANCE FROM INSIDE OF BEND TO SHANK END DISTANCE FROM INSIDE OF BEND TO SHANK END NONE. 2D AND 1B MODE REPLY21AA051AC20 CQZSJ 04DEPTH,SLOT,SHAFT SHAFT SLOT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQZTJ 04ANGLE,CHAMFER,LEFT CORNER,OUTSIDE OUTSIDE LEFT CORNER CHAMFER ANGLE NONE. REPLACED BY MRC CSYT WITH ISAC 0368. 2D AND 1B MODE REPLY21AP381AC20 CQZWJ /D/ 10AMOUNT,INGREDIENT,ACTIVE,MULTILAYER MULTILAYER ACTIVE INGREDIENT AMOUNT THE AMOUNT OF ACTIVE INGREDIENT/S/ CONTAINED IN EACH LAYER OF A MULTILAYERED ITEM. 3D AND 1B MODE REPLY32AG535AG541AN98 CQZXJ 04DISTANCE BETWEEN CENTERLINES OF COVER PLATE MOUNTING FACILITIES PARALLEL TO WIDTH DISTANCE BETWEEN CENTERLINES OF COVER PLATE MOUNTING FACILITIES PARALLEL TO WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CQZYJ 04DISTANCE FROM DISK TO TOP DISTANCE FROM DISK TO TOP NONE. 2D AND 1B MODE REPLY21AA051AC20 CQZZJ 04DISTANCE FROM OUTSIDE FLATTED PORTION TO OPPOSITE SURFACE DISTANCE FROM OUTSIDE FLATTED PORTION TO OPPOSITE SURFACE NONE. 2D AND 1B MODE REPLY21AA051AC20 CRBBJ 10WIDTH PER FUNCTION,BAND,FREQUENCY FREQUENCY BAND WIDTH PER FUNCTION THE DIFFERENCE,PER FUNCTION,BETWEEN THE LIMITING FREQUENCIES WITHIN WHICH PERFORMANCE,IN RESPECT TO SOME CHARACTERISTIC,FALLS WITHIN SPECIFIED LIMITS. 2D AND 1B MODE REPLY21AE062AF15 CRBCJ 10DISCRIMINATION AT SPECIFIED FREQUENCIES PER FUNCTION IN DECIBELS DISCRIMINATION AT SPECIFIED FREQUENCIES PER FUNCTION IN DECIBELS THE ALGEBRAIC DIFFERENCE BETWEEN THE INSERTION LOSS AT A SPECIFIED FREQUENCY AND THE INSERTION LOSS AT THE REFERENCE FREQUENCY PER FUNCTION,EXPRESSED IN DECIBELS. 2D AND 1B MODE REPLY21AC202AF15 CRBDJ /D/ 04WIDTH,FLANGE,BEARING BEARING FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRBFJ 04THICKNESS,KEY,FIRST FIRST KEY THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CRBGJ A19PROVISION AND QUANTITY,INSULATION,SHUNT SHUNT INSULATION PROVISION AND QUANTITY AN INDICATION OF WHETHER OR NOT A COVERING MATERIAL IS PROVIDED AND THE NUMBER OF SHUNTS INCLUDED. 1D AND 1A MODE REPLY11AA47 CRBHJ /D/ 04DIAMETER,MINOR,TAPERED MOUNTING TAPERED MOUNTING MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRBJJ A19DOCUMENT AND CLASSIFICATION,SURFACE TREATMENT,CONTACT CONTACT SURFACE TREATMENT DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE CONTACT SURFACE TREATMENT MATERIAL. 2D AND 1A MODE REPLY21AP331AP39 CRBKJ /D/ 13THREAD QUANTITY,TERMINAL,FUNCTIONAL FUNCTIONAL TERMINAL THREAD QUANTITY THE NUMBER OF THREADS ON A FUNCTIONAL TERMINAL,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AB391AC00 CRBLH /D/ 19FITTING/COMPONENT AND MATERIAL,END,SECOND SECOND END FITTING/COMPONENT AND MATERIAL THE NAME OF THE FITTING AND/OR COMPONENT AND THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH IT IS FABRICATED. 2D MODE REPLY 22AC426AD09 CRBMA 12QUANTITY,ACCOMMODATION,CONDUCTOR MECHANICAL CONDUCTOR MECHANICAL ACCOMMODATION QUANTITY THE NUMBER OF MECHANICAL ACCOMMODATIONS PROVIDED TO PHYSICALLY SPACE AND/OR SUPPORT ELECTRICAL CONDUCTORS. 1A MODE REPLY 0 CRBNJ 10LIMITS PER FUNCTION,FREQUENCY,VOLTAGE STANDING WAVE RATIO VOLTAGE STANDING WAVE RATIO FREQUENCY LIMITS PER FUNCTION THE MINIMUM AND MAXIMUM VALUES OF FREQUENCY,PER FUNCTION,BETWEEN WHICH THE VOLTAGE STANDING WAVE RATIO IS SPECIFIED. 2D AND 1B MODE REPLY21AE062AF15 CRBPB /D/ 04TAPER PER METER IN MILLIMETERS,RING,INNER INNER RING TAPER PER METER IN MILLIMETERS NONE. 1B MODE REPLY 0 CRBQD /D/ 13THREAD SERIES DESIGNATOR,CONDUCTOR ACCOMMODATION CONDUCTOR ACCOMMODATION THREAD SERIES DESIGNATOR A DESIGNATION INDICATING THE DIAMETER-PITCH AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO THE DIAMETER OF THE CONDUCTOR ACCOMMODATION. SELECT REPLY CODE 10AH06 CRBRJ /D/ 04DIAMETER,BORE,ROD END ROD END BORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRBSJ T10TOLERANCE,OUTSIDE DIAMETER,GAGING SURFACE GAGING SURFACE OUTSIDE DIAMETER TOLERANCE THE LIMITS OF PERMISSIBLE VARIATION ON THE OUTSIDE DIAMETER OF THE GAGING SURFACE. 1D AND 1F MODE REPLY11AA05 CRBTJ 04LENGTH,CANTILEVER CANTILEVER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRBWD 19STABILIZER STABILIZER ANY SUBSTANCE WHICH MAKES A DRUG PREPARATION MORE STABLE. SELECT REPLY CODE 10AP14 CRBXJ /D/ 04DIAMETER,OUTSIDE,SWAGE SWAGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRBYJ 10POUR POINT,MAXIMUM MAXIMUM POUR POINT THE LOWEST TEMPERATURE AT WHICH THE ITEM IS OBSERVED TO FLOW. 1D AND 1B MODE REPLY11AB36 CRBZJ 10CURRENT,OPERATING,WINDING WINDING OPERATING CURRENT THE AMOUNT OF OPERATING CURRENT FOR WHICH THE WINDING IS DESIGNED. 3D AND 1B MODE REPLY32AN862AN871AC20 CRCBJ /D/ 04DIAMETER,MINOR,TURRET TURRET MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRCCJ 04WIDTH,RECEPTACLE,POSITIVE LOCK POSITIVE LOCK RECEPTACLE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRCDH /D/ 05DIRECTION AND PUMP DESIGNATION,ROTATION,SHAFT SHAFT ROTATION DIRECTION AND PUMP DESIGNATION THE DIRECTION IN WHICH THE SHAFT OF AN ITEM ROTATES,AND THE PUMP DESIGNATION. 2D MODE REPLY 23AA383AA96 CRCFJ 10TEMP RATING,AMBIENT,TRIP RELEASE TRIP RELEASE AMBIENT TEMP RATING THE TEMPERATURE OF THE MEDIUM SURROUNDING THE TRIP RELEASE AT WHICH IT CAN BE OPERATED CONTINUOUSLY. 2D AND 1B MODE REPLY21AB361AC20 CRCGJ /D/A13THREAD QUANTITY PER INCH AND SEQUENCE DESIGNATION,MOUNTING MOUNTING THREAD QUANTITY PER INCH AND SEQUENCE DESIGNATION THE NUMBER OF THREADS PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS AND THE MOUNTING SEQUENCE OF THE THREADED FACILITY. 1D AND 1A MODE REPLY12AP26 CRCHJ 04DIAMETER,JOINT,SOCKET SOCKET JOINT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRCJA /D/ 16STYLE,SHAPE,CROSS-SECTIONAL,SEAL SEAL CROSS-SECTIONAL SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE CROSS-SECTIONAL SHAPE OF THE SEAL. 1A MODE REPLY 0 CRCKJ 13THREAD DIAMETER THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CRCLJ 10PERCENTAGE,RETENTION,MOISTURE CONTENT MOISTURE CONTENT RETENTION PERCENTAGE THE MOISTURE CONTENT RETAINED IN THE ITEM AFTER SEASONING,EXPRESSED IN PERCENT. 1D AND 1B MODE REPLY11AC20 CRCMJ 10VOLTAGE DROP IN MILLIVOLTS VOLTAGE DROP IN MILLIVOLTS THE LOSS OF POTENTIAL RESULTING FROM THE INHERENT OPPOSITION TO THE FLOW OF ELECTRICITY ACROSS THE ITEM,EXPRESSED IN MILLIVOLTS. 1D AND 1B MODE REPLY11AC20 CRCNJ /D/ 04ANGLE,SEAT,SECOND END SECOND END SEAT ANGLE THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS. 2D AND 1B MODE REPLY21AP381AC20 CRCPJ /D/ 10VOLTAGE RATING,PEAK PEAK VOLTAGE RATING THE MAXIMUM INSTANTANEOUS VOLTAGE FOR WHICH AN ITEM IS RATED. 1D AND 1B MODE REPLY12AN86 CRCQJ T10RANGE AND FUNCTION,INTENSITY,LIGHT LIGHT INTENSITY RANGE AND FUNCTION THE MINIMUM AND MAXIMUM VALUES OF THE LIGHT INTENSITY AND THE FUNCTION OF THE ITEM. 2D AND 1F MODE REPLY21AP251AE28 CRCRD /D/ 19ACTION,SWITCHING,CAM CAM SWITCHING ACTION AN INDICATION OF THE SWITCHING ACTION BY THE ROTATING CAM. SELECT REPLY CODE 10AD78 CRCSJ 04ANGLE,HEAD HEAD ANGLE THE ANGLE OF THE HEAD. 2D AND 1B MODE REPLY21AP381AC20 CRCTJ 10CURRENT RATING AND TYPE CURRENT RATING AND TYPE INDICATES THE TYPE OF CURRENT AND THE RATED VALUE FOR WHICH THE ITEM IS DESIGNED. 3D AND 1B MODE REPLY32AN861AC202AN87 CRCWD /D/ 19FORM,DISCHARGE,AEROSOL AEROSOL DISCHARGE FORM THE FORM OF THE CONTENTS EXPELLED FROM A PRESSURIZED CONTAINER. SELECT REPLY CODE 10AL82 CRCXJ 04DEPTH,HOLE,WIRE,TERMINAL TERMINAL WIRE HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRCYJ /D/ 04DISTANCE FROM BRUSH TOP TO SLOT DISTANCE FROM BRUSH TOP TO SLOT NONE. 2D AND 1B MODE REPLY21AA051AC20 CRCZJ /D/ 04DISTANCE BETWEEN MOUNTING FACILITY CENTER AND KEY END DISTANCE BETWEEN MOUNTING FACILITY CENTER AND KEY END NONE. 2D AND 1B MODE REPLY21AA051AC20 CRDBH /D/ 13THREAD SERIES DESIGNATOR,TERMINAL,FUNCTIONAL FUNCTIONAL TERMINAL THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF FUNCTIONAL TERMINAL THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D MODE REPLY 21AC002AH06 CRDCJ 10VOLTAGE,DC,MAXIMUM DIELECTRIC WITHSTANDING MAXIMUM DIELECTRIC WITHSTANDING DC VOLTAGE THE MAXIMUM DIRECT CURRENT VOLTAGE THAT THE INSULATING MATERIAL/S/ OF THE ITEM WILL WITHSTAND WITHOUT RESULTING IN DISRUPTIVE DISCHARGE OR DETERIORATION. 2D AND 1B MODE REPLY21AB631AD86 CRDDJ 10OUTPUT IN MICROWATTS,LIGHT LIGHT OUTPUT IN MICROWATTS THE AMOUNT OF LIGHT OUTPUT AT A GIVEN DISTANCE FROM THE SOURCE PER SPECIFIC MEASUREMENT SCALE,EXPRESSED IN MICROWATTS. 2D AND 1B MODE REPLY21AB391AE23 CRDFJ /D/ 04DIAMETER,BORE,NEEDLE BEARING NEEDLE BEARING BORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRDGJ 04WIDTH,LIP LIP WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRDHJ 04DEPTH,SLOT,RELIEF,FIRST FIRST RELIEF SLOT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRDJJ /D/ 04WIDTH,RING,INNER,BEARING BEARING INNER RING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRDKJ 04LENGTH,SHACKLE SHACKLE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRDLD 08LOCATION,JOINT,UNION UNION JOINT LOCATION INDICATES THE LOCATION OF THE UNION JOINT ON THE ITEM. SELECT REPLY CODE 10AN73 CRDMJ 04WIDTH,KEY,SECOND SECOND KEY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRDNJ T10COEFFICIENT OF CAPACITANCE RANGE PER SECTION IN PPM PER DEG CELSIUS,TEMP TEMP COEFFICIENT OF CAPACITANCE RANGE PER SECTION IN PPM PER DEG CELSIUS THE MINIMUM AND MAXIMUM VALUES OF THE PERMISSIBLE CHANGE IN CAPACITANCE PER SECTION CAUSED BY A CHANGE IN TEMPERATURE,EXPRESSED IN PARTS PER MILLION PER DEGREE CELSIUS. 1D AND 1F MODE REPLY12AH19 CRDPJ /D/ 04RADIUS,ROLLER ROLLER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CRDQB 04ANGLE IN DEG,COUNTERSINK,GROMMET GROMMET COUNTERSINK ANGLE IN DEG NONE. 1B MODE REPLY 0 CRDRD 18TYPE,GLUE GLUE TYPE INDICATES THE TYPE OF GLUE USED TO FABRICATE THE ITEM. SELECT REPLY CODE 10AN74 CRDSJ /D/ 04HEIGHT,STEP,MOUNTING CLAMP MOUNTING CLAMP STEP HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CRDTJ 04WIDTH,NOTCH,SHOULDER SHOULDER NOTCH WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRDWJ 10PRESSURE,TEST,HYDROSTATIC HYDROSTATIC TEST PRESSURE A STEADY,UNIFORM,INTERNAL,STATIC PRESSURE THAT THE ITEM MUST WITHSTAND WITHOUT LEAKAGE,ABNORMAL DISTORTION,OR DAMAGE. 1D AND 1B MODE REPLY11AN71 CRDXJ 10CAPACITY,MAXIMUM,TIRE LOAD TIRE LOAD MAXIMUM CAPACITY THE DETERMINATION OF THE MAXIMUM OPERATIONAL LOAD CARRYING CAPACITY FOR WHICH THE TIRE IS RATED. 2D AND 1B MODE REPLY21AN931AN82 CRDYD 08LOCATION,END,FIRST FIRST END LOCATION INDICATES THE LOCATION OF THE FIRST END. SELECT REPLY CODE 10AN73 CRDZJ /D/ 10HORSEPOWER RATING AND DESIGNATION,PRIME MOVER PRIME MOVER HORSEPOWER RATING AND DESIGNATION AN INDICATION OF THE RATED HORSEPOWER OF THE PRIME MOVER,AND ITS DESIGNATION. 1D AND 1B MODE REPLY11AP23 CRFBJ 04DISTANCE BETWEEN DOME HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN DOME HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 CRFCJ 04LENGTH,TONGUE,FIRST FIRST TONGUE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRFDH /D/ 18TYPE-LOCATION AND PUMP DESIGNATION,CONNECTION CONNECTION TYPE-LOCATION AND PUMP DESIGNATION INDICATES THE TYPE AND LOCATION OF THE CONNECTION ON THE ITEM AND THE PUMP DESIGNATION. 3D MODE REPLY 32AP223AN733AA96 CRFFJ /D/ 04DIAMETER,BORE,SMALLEST,BEARING BEARING SMALLEST BORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRFGD 18TYPE,CONNECTION,QUICK DISCONNECT END QUICK DISCONNECT END CONNECTION TYPE INDICATES THE TYPE OF END CONNECTION ON THE QUICK DISCONNECT. SELECT REPLY CODE 10AH46 CRFHJ 04WIDTH,INSIDE,WAVEGUIDE WAVEGUIDE INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRFJJ T10COEFFICIENT OF RESISTANCE PER SECTION IN PPM PER DEG CELSIUS,TEMP TEMP COEFFICIENT OF RESISTANCE PER SECTION IN PPM PER DEG CELSIUS A CONSTANT THAT REPRESENTS THE PROPORTIONATE CHANGE IN RESISTANCE CAUSED BY A CHANGE IN TEMPERATURE PER SECTION,EXPRESSED IN PARTS PER MILLION PER DEGREE CELSIUS. 1D AND 1F MODE REPLY12AH19 CRFKD /D/ 07SUPPRESSION,INTERFERENCE,ELECTROMAGNETIC ELECTROMAGNETIC INTERFERENCE SUPPRESSION AN INDICATION OF WHETHER OR NOT PROVISIONS TO SUPPRESS ELECTROMAGNETIC INTERFERENCE /EMI/ ARE PROVIDED. SELECT REPLY CODE 10AB22 CRFLJ 13SCREW THREAD DIAMETER AND LOCATION SCREW THREAD DIAMETER AND LOCATION THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COAXIAL CYLINDER WHICH WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD AND TERMINATES AT THE CIRCUMFERENCE,AND THE THREAD LOCATION. 3D AND 1B MODE REPLY33AN731AA051AC20 CRFMJ 10PULL RATING PULL RATING THE AMOUNT OF APPLIED FORCE OR EFFORT REQUIRED TO MOVE THE ITEM. 2D AND 1B MODE REPLY22AN751AC20 CRFNA /D/ 12QUANTITY,CONTACT,STATIONARY,INSULATED INSULATED STATIONARY CONTACT QUANTITY THE NUMBER OF STATIONARY CONTACTS ON ONE SURFACE THAT ARE ELECTRICALLY INSULATED FROM THE OPPOSITE SURFACE. 1A MODE REPLY 0 CRFPJ /D/ 04DISTANCE BETWEEN TURRETS DISTANCE BETWEEN TURRETS NONE. 2D AND 1B MODE REPLY21AA051AC20 CRFQJ /D/ 10FREQUENCY IN HERTZ PER POLE FREQUENCY IN HERTZ PER POLE THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT FOR EACH POLE. 2D AND 1B MODE REPLY21AC202AP31 CRFRJ /D/A12QUANTITY PER TERTIARY CONTAINER,SECONDARY CONTAINER SECONDARY CONTAINER QUANTITY PER TERTIARY CONTAINER THE NUMBER OF SECONDARY CONTAINERS WITHIN EACH TERTIARY CONTAINER. 1D AND 1A MODE REPLY13AN65 CRFSJ /D/ 04DISTANCE BETWEEN CENTERLINES OF BOSS AND MOUNTING FACILITY PARALLEL TO LENGTH DISTANCE BETWEEN CENTERLINES OF BOSS AND MOUNTING FACILITY PARALLEL TO LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRFTJ 04ANGLE,CHAMFER,RIGHT CORNER,OUTSIDE OUTSIDE RIGHT CORNER CHAMFER ANGLE NONE. REPLACED BY MRC CSYT WITH ISAC 0368. 2D AND 1B MODE REPLY21AP381AC20 CRFWJ 04WIDTH,GROOVE,FIRST RADIAL FIRST RADIAL GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRFXF T10TOLERANCE FOR OPERATING TEMP IN PERCENT,FREQUENCY FREQUENCY TOLERANCE FOR OPERATING TEMP IN PERCENT THE PERMISSIBLE FREQUENCY DEVIATION WITHIN THE OPERATING TEMPERATURE RANGE,EXPRESSED IN PERCENT. 1F MODE REPLY 0 CRFYJ 04ANGLE,FLOW FLOW ANGLE THE ANGLE THAT THE FLOW IS TURNED FROM THE STRAIGHT FLOW. 1D AND 1B MODE REPLY11AP38 CRFZA 10LENGTH OF SERVICE LENGTH OF SERVICE THE NUMBER OF YEARS REPRESENTED BY THE ITEM. 1A MODE REPLY 0 CRGBJ 10SPACING,HOLE,FOURTH MOUNTING FOURTH MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 CRGCH /D/ 18TYPE AND SERVICE USAGE,SOLUTION,PRESERVATIVE PRESERVATIVE SOLUTION TYPE AND SERVICE USAGE INDICATES THE TYPE OF SOLUTION USED FOR PRESERVATION AND THE SERVICE USAGE OF THE ITEM. 2D MODE REPLY 22AK892AN66 CRGDJ 10DISSIPATION RATING PER SECTION IN WATTS,POWER POWER DISSIPATION RATING PER SECTION IN WATTS THE MAXIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED PER SECTION,EXPRESSED IN WATTS. 2D AND 1B MODE REPLY21AC892AH19 CRGFL 16STYLE,THREAD,NONMACHINE NONMACHINE THREAD STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF A NONMACHINE THREAD. 1L MODE REPLY 0 CRGGD /D/ 19POSITION,LOCKING,SWITCH ACTUATOR SWITCH ACTUATOR LOCKING POSITION THE POSITION OF THE SWITCH ACTUATOR AT WHICH THE LOCKING METHOD IS EFFECTIVE. SELECT REPLY CODE 10AD91 CRGHJ /D/ 10PRESSURE AND DESIGNATION,OPERATING,POWER DRIVE,PRIME MOVER PRIME MOVER POWER DRIVE OPERATING PRESSURE AND DESIGNATION THE PRESSURE REQUIRED TO ACTUATE THE POWER DRIVE UNIT OF THE PRIME MOVER,AND ITS DESIGNATION. 2D AND 1B MODE REPLY22AG201AP23 CRGJJ /D/ 04DIAMETER,COUNTERBORE,END END COUNTERBORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRGKJ 04DEPTH,KEY,SECOND SECOND KEY DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRGLJ /D/ 04LENGTH,FLAT,MOUNTING CLAMP MOUNTING CLAMP FLAT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRGMH 19CONFORMITY PER SECTION,FUNCTION FUNCTION CONFORMITY PER SECTION THE FIDELITY OF THE RELATIONSHIP BETWEEN THE ACTUAL FUNCTION CHARACTERISTICS AND THE THEORETICAL FUNCTION PER SECTION. 2D MODE REPLY 22AH191AC86 CRGNJ /D/ 04DISTANCE BETWEEN SECOND AND THIRD POSTS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SECOND AND THIRD POSTS NONE. 2D AND 1B MODE REPLY21AA051AC20 CRGPH /D/ 19PHASE PER POWER SOURCE,INPUT INPUT PHASE PER POWER SOURCE THE NUMBER OF INPUT PHASES PER POWER SOURCE. 2D MODE REPLY 21AD022AP27 CRGQJ 04DISTANCE BETWEEN HOOKS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN HOOKS NONE. 2D AND 1B MODE REPLY21AA051AC20 CRGRH /D/ 18TYPE AND LOCATION,ADJUSTMENT,CONTACT ACTUATING DIFFERENTIAL CONTACT ACTUATING DIFFERENTIAL ADJUSTMENT TYPE AND LOCATION INDICATES THE TYPE AND LOCATION OF THE DEVICE PROVIDED FOR MANUAL ADJUSTMENT OF THE CONTACT ACTUATING DIFFERENTIAL. 2D MODE REPLY 23AN732AG18 CRGSB 10RESISTANCE RATING IN OHMS,DC DC RESISTANCE RATING IN OHMS THE OPPOSITION TO THE FLOW OF DIRECT CURRENT OFFERED BY AN ITEM,EXPRESSED IN OHMS. 1B MODE REPLY 0 CRGTJ 04DISTANCE FROM KINGPIN CENTER TO FRONT END DISTANCE FROM KINGPIN CENTER TO FRONT END THE DISTANCE FROM THE KINGPIN CENTER TO THE FRONT END. 2D AND 1B MODE REPLY21AA051AC20 CRGWB 10DEVIATION IN PPM PER DEG CELSIUS,TEMP COEFFICIENT,MAXIMUM MAXIMUM TEMP COEFFICIENT DEVIATION IN PPM PER DEG CELSIUS THE MAXIMUM DEVIATION BETWEEN TEMPERATURE COEFFICIENT OF THE INDIVIDUAL ELEMENTS OF THE ITEM,EXPRESSED IN PARTS PER MILLION PER DEGREE CELSIUS. 1B MODE REPLY 0 CRGXD 19RELATIONSHIP TO PRIMARY WASHER,SECONDARY WASHER SECONDARY WASHER RELATIONSHIP TO PRIMARY WASHER AN INDICATION OF WHETHER OR NOT THE SECONDARY IS IDENTICAL TO THE PRIMARY WASHER. SELECT REPLY CODE 10AF63 CRGYD /D/ 07HEATER,ELECTRIC ELECTRIC HEATER AN INDICATION OF WHETHER OR NOT AN ELECTRIC HEATER IS INCLUDED. SELECT REPLY CODE 10AA49 CRGZJ 10REACTANCE IN OHMS,ZSO,PLUS J PLUS J ZSO REACTANCE IN OHMS THE REACTANCE (X) PART OF THE STATOR IMPEDANCE WITH THE ROTOR OPEN (ZSO),EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 CRHBJ /D/X19IDENTIFICATION,TOOL,CRIMPING CRIMPING TOOL IDENTIFICATION THE CONTROLLING ACTIVITY AND IDENTIFYING NUMBER OF THE CRIMPING TOOL. 1D AND 1A MODE REPLY15AN63 CRHCL 16STYLE,CONFIGURATION,HOLE HOLE CONFIGURATION STYLE THE STYLE DESIGNATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HOLE CONFIGURATION. 1L MODE REPLY 0 CRHDJ T10TOLERANCE OF TEMP COEFFICIENT PER SECTION PPM PER DEG CELSIUS TOLERANCE OF TEMP COEFFICIENT PER SECTION IN PPM PER DEG CELSIUS THE LIMITS OF PERMISSIBLE DEVIATION OF THE TEMPERATURE COEFFICIENT PER SECTION FROM THE RATED VALUE,EXPRESSED IN PARTS PER MILLION PER DEGREE CELSIUS. 1D AND 1F MODE REPLY12AH19 CRHFA 10CAPACITY,DECIMAL,MAXIMUM MAXIMUM DECIMAL CAPACITY THE MAXIMUM NUMBER OF DECIMALS ACCOMMODATED. 1A MODE REPLY 0 CRHGJ 04DISTANCE FROM MOUNTING HOLE CENTER TO BASE EDGE,FIRST FIRST DISTANCE FROM MOUNTING HOLE CENTER TO BASE EDGE NONE. 2D AND 1B MODE REPLY21AA051AC20 CRHHJ /D/ 04DISTANCE BETWEEN SHAFT AND MOUNTING CENTERLINE,HORIZONTAL HORIZONTAL DISTANCE BETWEEN SHAFT AND MOUNTING CENTERLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 CRHJJ A19FACTOR,QUALITY QUALITY FACTOR THE QUALITY FACTOR OF AN ITEM WITH RESPECT TO A SPECIFIED FREQUENCY FOR THE RATED INDUCTANCE. 1D AND 1A MODE REPLY11AC20 CRHKJ /D/A12QUANTITY AND PUMP DESIGNATION,STAGE STAGE QUANTITY AND PUMP DESIGNATION THE NUMBER OF STAGES INCORPORATED IN THE ITEM,AND THE PUMP DESIGNATION. 1D AND 1A MODE REPLY13AA96 CRHLA 12QUANTITY,BIT BIT QUANTITY THE NUMBER OF BINARY DIGITS THE ITEM CAN GENERATE,PROCESS OR STORE. 1A MODE REPLY 0 CRHMJ /D/ 04ANGLE,SEAT,THIRD END THIRD END SEAT ANGLE THE ANGLE OF THE THIRD END SURFACE UPON WHICH THE MATED SURFACE SEATS. 2D AND 1B MODE REPLY21AP381AC20 CRHNJ 04WIDTH,SLOT,SHAFT SHAFT SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRHPJ /D/ 04LENGTH AND SEQUENCE DESIGNATION,SLOT,MOUNTING MOUNTING SLOT LENGTH AND SEQUENCE DESIGNATION NONE. 3D AND 1B MODE REPLY31AA051AC202AP26 CRHQD /D/ 11METHOD,JOINING JOINING METHOD THE MEANS BY WHICH MULTIPLE ITEMS ARE JOINED. SELECT REPLY CODE 10AP47 CRHRL 16STYLE,BRUSH,FIRST FIRST BRUSH STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FIRST BRUSH. 1L MODE REPLY 0 CRHSJ 13THREAD SIZE,NOMINAL,INLET INLET NOMINAL THREAD SIZE DESIGNATES THE NOMINAL THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF AN INLET THREADED HOLE. 1D AND 1B MODE REPLY11AA05 CRHTJ 04DISTANCE FROM CENTER OF EYE TO SHANK END DISTANCE FROM CENTER OF EYE TO SHANK END NONE. 2D AND 1B MODE REPLY21AA051AC20 CRHWJ /D/ 04DIAMETER,OUTSIDE,CLINCH PLATE CLINCH PLATE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRHXJ A18TYPE ACCOMMODATED AND QUANTITY,LAMP LAMP TYPE ACCOMMODATED AND QUANTITY INDICATES THE TYPE AND NUMBER OF LAMPS THAT THE ITEM CAN ACCOMMODATE. 1D AND 1A MODE REPLY12AD48 CRHYJ 04HEIGHT,RISE RISE HEIGHT THE VERTICAL MEASUREMENT FROM THE LINE OF END SUPPORTS TO THE CENTER OF THE INSIDE CURVE. 2D AND 1B MODE REPLY21AA051AC20 CRHZB 10FREQUENCY IN HERTZ,REED,RESONANT RESONANT REED FREQUENCY IN HERTZ THE NUMBER OF CYCLIC CHANGES PER SECOND (HERTZ) AT WHICH A RESONANT REED VIBRATES TO EFFECT THE CLOSING OR OPENING OF THE CONTACTS. 1B MODE REPLY 0 CRJBJ 04DIAMETER FROM HEAD,TENTH TENTH DIAMETER FROM HEAD NONE. 2D AND 1B MODE REPLY21AA051AC20 CRJCJ 04DISTANCE FROM CONDUCTOR GROOVE TO INSULATOR END,FIRST FIRST DISTANCE FROM CONDUCTOR GROOVE TO INSULATOR END NONE. 2D AND 1B MODE REPLY21AA051AC20 CRJDG 04LENGTH,RANDOM RANDOM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH. FULL TEXT WRITE-IN 0 CRJFD 08LOCATION,PLUG,DRAIN DRAIN PLUG LOCATION INDICATES THE LOCATION OF THE DRAIN PLUG ON THE ITEM. SELECT REPLY CODE 10AN73 CRJGA 13THREAD QUANTITY PER INCH,INLET INLET THREAD QUANTITY PER INCH THE NUMBER OF SCREW THREADS ON THE INLET PER LINEAR INCH,INCLUDING INCOMPLETE THREADS ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CRJHA 12QUANTITY,POSITION,SWITCH ACTUATOR INDEXING SWITCH ACTUATOR INDEXING POSITION QUANTITY THE NUMBER OF POSITIONS TO WHICH THE SWITCH ACTUATOR MAY BE INDEXED. 1A MODE REPLY 0 CRJJA /D/ 13THREAD QUANTITY PER INCH,BULKHEAD BULKHEAD THREAD QUANTITY PER INCH THE NUMBER OF BULKHEAD SCREW THREADS PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CRJKJ 04DIAMETER,HOLE,CENTER STUD CENTER STUD HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRJLJ 04HEIGHT,CAP,SECOND SECOND CAP HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CRJMD 19PROTECTION,ENVIRONMENTAL,OUTER COVERING OUTER COVERING ENVIRONMENTAL PROTECTION THE TYPE OF PROTECTION PROVIDED BY THE OUTER COVERING. SELECT REPLY CODE 10AA65 CRJNJ 10SPACING,HOLE,SECOND MOUNTING SECOND MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 CRJPA 19NUMBER,IDENTIFYING,CRIMPING TOOL CRIMPING TOOL IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE CRIMPING TOOL. 1A MODE REPLY 0 CRJQD 14SHAPE ACCOMMODATED,SURFACE SURFACE SHAPE ACCOMMODATED THE PHYSICAL CONFIGURATION OF THE SURFACE THAT THE ITEM WILL ACCOMMODATE. SELECT REPLY CODE 10AP00 CRJRJ /D/ 10FREQUENCY IN HERTZ AND DESIGNATION,PRIME MOVER PRIME MOVER FREQUENCY IN HERTZ AND DESIGNATION THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT OF THE PRIME MOVER,AND ITS DESIGNATION. 1D AND 1B MODE REPLY11AP23 CRJSJ A12QUANTITY PER SECTION,TAP,FIXED FIXED TAP QUANTITY PER SECTION THE NUMBER OF FIXED TERMINALS AT POINTS BETWEEN THE END TERMINALS THAT PROVIDE CONNECTION TO THE INTERMEDIATE VALUES OF THE TOTAL VALUE PER SECTION. 1D AND 1A MODE REPLY12AH19 CRJTJ 10CAPACITY,TANK,FUEL,INTEGRAL INTEGRAL FUEL TANK CAPACITY THE AMOUNT OF FUEL THAT THE INTEGRAL TANK WILL HOLD. 1D AND 1B MODE REPLY12AN64 CRJWJ 04DISTANCE,KNURL TO END KNURL TO END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CRJXJ 04DIAMETER,MINOR,TAPERED END,SHAFT SHAFT TAPERED END MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRJYJ 04ANGLE,CHAMFER,LEFT CORNER,INSIDE INSIDE LEFT CORNER CHAMFER ANGLE NONE. REPLACED BY MRC CSYT WITH ISAC 0368. 2D AND 1B MODE REPLY21AP381AC20 CRJZD 19RELATIONSHIP TO FIRST BRUSH,SECOND BRUSH SECOND BRUSH RELATIONSHIP TO FIRST BRUSH AN INDICATION OF WHETHER OR NOT THE SECOND BRUSH IS IDENTICAL TO THE FIRST BRUSH. SELECT REPLY CODE 10AA37 CRKBJ 04ANGLE,INCLUDED,RIB RIB INCLUDED ANGLE THE INCLUDED ANGLE BETWEEN THE RIBS. 2D AND 1B MODE REPLY21AP381AC20 CRKCJ 04LENGTH,CUT,CORNER CORNER CUT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRKDJ 04THICKNESS,SHACKLE SHACKLE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CRKFJ /D/ 13THREAD DIAMETER,ACCOMMODATION,CONDUCTOR CONDUCTOR ACCOMMODATION THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CONDUCTOR ACCOMMODATION,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CRKGJ 04ANGLE,RECESS,BOTTOM BOTTOM RECESS ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CRKHJ 04HEIGHT,STEP,THIRD THIRD STEP HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CRKJJ /D/A08LOCATION AND QUANTITY,PLY,TIRE TIRE PLY LOCATION AND QUANTITY THE ACTUAL NUMBER OF PLIES FROM ONE BEAD AROUND AND EXTENDING TO THE OTHER BEAD AND/OR THE ACTUAL NUMBER OF PLIES (BELTS AND BREAKERS) EXTENDING SHOULDER TO SHOULDER RUNNING CIRCUMFERENTIALLY AROUND THE TIRE. 1D AND 1A MODE REPLY13AN73 CRKKJ 04ANGLE,COUNTERSINK,MAJOR,HEAD HEAD MAJOR COUNTERSINK ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CRKLJ 10REACTANCE IN OHMS,ZRS,PLUS J PLUS J ZRS REACTANCE IN OHMS THE REACTANCE /X/ PART OF THE ROTOR IMPEDANCE WITH THE STATOR SHORTED /ZRS/,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 CRKMJ 04WIDTH,OVERALL,LATCH LATCH OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE LATCH, IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CRKNJ /D/ 10FREQUENCY PER SECTION IN HERTZ FREQUENCY PER SECTION IN HERTZ THE NUMBER OF COMPLETE CYCLES PER SECOND OF ALTERNATING CURRENT PER SECTION.MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1D AND 1B MODE REPLY12AH19 CRKPD 18TYPE,STEM STEM TYPE INDICATES THE TYPE OF STEM FURNISHED WITH THE ITEM. SELECT REPLY CODE 10AC61 CRKQJ /D/ 04HEIGHT,SHIELD SHIELD HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CRKRD /D/ 08LOCATION,JOINT,UNION UNION JOINT LOCATION INDICATES THE LOCATION OF THE UNION JOINT. SELECT REPLY CODE 10AN73 CRKSJ T10TOLERANCE PER SECTION,LOCATION,TAP TAP LOCATION TOLERANCE PER SECTION THE LIMITS OF PERMISSIBLE VARIATION FROM THE RATED VALUE OF THE LOCATION OF A TAP PER SECTION. 2D AND 1F MODE REPLY21AD002AH19 CRKTJ /D/ 04DISTANCE BETWEEN SHAFT AND MOUNTING CENTERLINE,VERTICAL VERTICAL DISTANCE BETWEEN SHAFT AND MOUNTING CENTERLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 CRKWJ /D/ 04DEPTH,COUNTERBORE,END END COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRKXJ 04DISTANCE ACROSS POINTS OF HEXAGONAL SHOULDER DISTANCE ACROSS POINTS OF HEXAGONAL SHOULDER THE DISTANCE ACROSS POINTS OF HEXAGONAL SHOULDER. 2D AND 1B MODE REPLY21AA051AC20 CRKYJ 10SPACING,HOLE,SECOND SECOND HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 CRKZH /D/ 13THREAD SERIES AND SEQUENCE DESIGNATION,MOUNTING MOUNTING THREAD SERIES AND SEQUENCE DESIGNATION A DESIGNATION INDICATING THE THREAD DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS FOR A SPECIFIC DIAMETER AND THE MOUNTING SEQUENCE. 2D MODE REPLY 22AH062AP26 CRLBJ 04HEIGHT,INSIDE,WAVEGUIDE WAVEGUIDE INSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CRLCJ 10FREQUENCY AT WHICH INDUCTANCE AND QUALITY FACTOR APPLIES FREQUENCY AT WHICH INDUCTANCE AND QUALITY FACTOR APPLIES THE SPECIFIED FREQUENCY AT WHICH THE INDUCTANCE AND QUALITY OF AN ITEM IS MEASURED. 1D AND 1B MODE REPLY11AE06 CRLDJ A19ARRANGEMENT,CONTACT,NONPILE-UP NONPILE-UP CONTACT ARRANGEMENT THE DESIGNATION THAT IDENTIFIES THE ELECTRICAL CONFIGURATION OF A NONPILE-UP CONTACT GROUP INCLUDING THE NUMBER OF SWITCHING POLES OR FORMS. 1D AND 1A MODE REPLY12AG28 CRLFJ 04WIDTH,SLOT,FIRST RELIEF FIRST RELIEF SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRLGJ /D/ 04DEPTH,KEYWAY,SEAT SEAT KEYWAY DEPTH THE DISTANCE MEASURED ALONG A STRAIGHT LINE FROM THE TOP TO THE INNERMOST POINT OF THE SEAT KEYWAY. 2D AND 1B MODE REPLY21AA051AC20 CRLHH /D/ 11METHOD AND LOCATION,CONNECTION,PRESSURE PRESSURE CONNECTION METHOD AND LOCATION THE MEANS PROVIDED FOR CONNECTING THE ITEM TO THE PRESSURE SOURCE AND THE LOCATION. 2D MODE REPLY 22AG223AN73 CRLJJ /D/ 10TIME IN SECONDS,OPERATING OPERATING TIME IN SECONDS THE PERIOD OF ELAPSED TIME BETWEEN THE OPENING AND CLOSING OF THE ITEM,EXPRESSED IN SECONDS. 1D AND 1B MODE REPLY11AC20 CRLKJ 12QUANTITY,CONTENT,PRIMARY CONTAINER PRIMARY CONTAINER CONTENT QUANTITY A NUMERIC VALUE OF THE VOLUME,FORM,OR DOSAGE WITHIN EACH PRIMARY CONTAINER. 1D AND 1B MODE REPLY12AN64 CRLLH /D/ 19FITTING/COMPONENT AND SURFACE TREATMENT,END,SECOND SECOND END FITTING/COMPONENT AND SURFACE TREATMENT THE NAME OF THE FITTING AND/OR COMPONENT AND THE PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF.PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE. 2D MODE REPLY 22AC426AD09 CRLMJ 04DISTANCE BETWEEN TERMINALS,CENTER TO CENTER,SECOND SECOND CENTER TO CENTER DISTANCE BETWEEN TERMINALS NONE. 2D AND 1B MODE REPLY21AA051AC20 CRLNJ /D/ 04DIAMETER,OUTSIDE,RING FLANGE RING FLANGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRLPJ A18TYPE AND QUANTITY,LENS LENS TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF LENSES INCLUDED IN THE ITEM. 1D AND 1A MODE REPLY12AP19 CRLQJ /D/ 04DIAMETER ACCOMMODATED,MAJOR,PLUG PLUG MAJOR DIAMETER ACCOMMODATED NONE. 2D AND 1B MODE REPLY21AA051AC20 CRLRJ 04DIAMETER AND LOCATION,COUNTERBORE COUNTERBORE DIAMETER AND LOCATION THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COUNTERBORE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE,AND THE LOCATION. 3D AND 1B MODE REPLY31AA051AC203AN73 CRLSD /D/ 19GRADE,DOUGLAS-FIR DOUGLAS-FIR GRADE AN INDICATION OF THE GRADE OF DOUGLAS-FIR. SELECT REPLY CODE 10AP02 CRLTJ 04DISTANCE,SEPARATION,CONDUCTOR CONDUCTOR SEPARATION DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CRLWJ 04LENGTH,SHANK,FASTENER STUD FASTENER STUD SHANK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRLXA 12QUANTITY,ACCOMMODATION,CONDUCTOR CONDUCTOR ACCOMMODATION QUANTITY THE NUMBER OF CONDUCTOR ACCOMMODATIONS INCLUDED ON THE ITEM. 1A MODE REPLY 0 CRLYD 11METHOD,MARKING,GRADUATION GRADUATION MARKING METHOD THE PROCESS USED IN MARKING THE GRADUATIONS ON THE ITEM. SELECT REPLY CODE 10AM12 CRLZJ /D/ 04THICKNESS,SHOULDER,PRIMARY WASHER PRIMARY WASHER SHOULDER THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CRMBJ /D/ 10CURRENT RATING PER VOLTAGE REFERENCE,LOAD,CONTACT CONTACT LOAD CURRENT RATING PER VOLTAGE REFERENCE THE AMOUNT OF CURRENT THAT THE CONTACTS ARE RATED TO MAKE OR BREAK WITH A SPECIFIED LOAD PER VOLTAGE REFERENCE. 3D AND 1B MODE REPLY32AN861AD922AD88 CRMCA /D/ 19IDENTIFICATION,MANUFACTURER AND CASE OUTLINE MANUFACTURER AND CASE OUTLINE IDENTIFICATION THE 5-POSITION COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE AND THE IDENTIFYING DESIGNATION OF THE CASE OUTLINE. 1A MODE REPLY 0 CRMDJ /D/ 13THREAD PITCH IN MILLIMETERS,INTERNAL,HEAD HEAD INTERNAL THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT HEAD INTERNAL THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1D AND 1B MODE REPLY11AC20 CRMFJ 13THREAD SIZE,NOMINAL,BRANCH BRANCH NOMINAL THREAD SIZE NONE. 1D AND 1B MODE REPLY11AA05 CRMGJ 04ANGLE,TAPER,FIRST END FIRST END TAPER ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CRMHJ /D/T10RANGE AND TYPE PER POLE IN AMPS,CURRENT,ADJUSTABLE TRIP SETTING ADJUSTABLE TRIP SETTING CURRENT RANGE AND TYPE PER POLE IN AMPS THE MINIMUM AND MAXIMUM VALUES AND THE CURRENT TYPE AT WHICH THE ADJUSTABLE TRIP CAN BE SET FOR EACH POLE,EXPRESSED IN AMPERES. 2D AND 1F MODE REPLY22AN872AP31 CRMJJ 10POWER RATING,WINDING WINDING POWER RATING THE MAXIMUM POWER FOR WHICH THE WINDING OF THE ITEM IS RATED. 1D AND 1B MODE REPLY12AN86 CRMKJ 04ANGLE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CRMLJ /D/ 04DIAMETER AND LOCATION,INSIDE INSIDE DIAMETER AND LOCATION THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ITEM,AND TERMINATES AT THE INSIDE CIRCUMFERENCE,AND THE LOCATION ON THE ITEM. 3D AND 1B MODE REPLY31AA051AC203AN73 CRMMJ 04LENGTH,TANGENT TANGENT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRMND 08LOCATION,DRIVE,INTERNAL INTERNAL DRIVE LOCATION INDICATES THE LOCATION OF THE INTERNAL DRIVE. SELECT REPLY CODE 10AN73 CRMPJ 10VALUE IN OHMS,RESISTANCE,EQUIVALENT EQUIVALENT RESISTANCE VALUE IN OHMS THE EQUIVALENT (EFFECTIVE) RESISTANCE FOR WHICH THE ITEM IS RATED,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 CRMQJ 04DIAMETER,NOMINAL,CONNECTION CONNECTION NOMINAL DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CONNECTION,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CRMRJ 04DIAMETER,THRU-HOLE,BODY BODY THRU-HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRMSD 19ARRANGEMENT,MATERIAL,INSULATING AIR SPACE INSULATING AIR SPACE MATERIAL ARRANGEMENT THE ARRANGEMENT OF MATERIAL SO AS TO PROVIDE AN INSULATING AIR SPACE. SELECT REPLY CODE 10AG85 CRMTJ 04LENGTH,OVERALL,SINGLE BRUSH SINGLE BRUSH OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRMWD 19SOURCE,MATERIAL,RAW RAW MATERIAL SOURCE THE ANIMAL ORGAN FROM WHICH THE MATERIAL IS MADE. SELECT REPLY CODE 10AM85 CRMXA 13THREAD QUANTITY PER INCH,END,SECOND SECOND END THREAD QUANTITY PER INCH THE NUMBER OF THREADS PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CRMYJ /D/ 19COMPOSITION PER LITER,MEDIUM,CULTURE CULTURE MEDIUM COMPOSITION PER LITER THE COMPOSITION OF THE INGREDIENTS PRESENT IN ONE LITER OF THE FINISHED MEDIUM. 2D AND 1B MODE REPLY22AG535AG54 CRMZD /D/ 07PAD,ABSORBENT ABSORBENT PAD AN INDICATION OF WHETHER OR NOT AN ABSORBENT PAD(S) IS INCLUDED. SELECT REPLY CODE 10AA49 CRNBJ 13THREAD SIZE,NOMINAL,SECOND END SECOND END NOMINAL THREAD SIZE THE DESIGNATION WHICH IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE NOMINAL THREAD SIZE. 1D AND 1B MODE REPLY11AA05 CRNCA /D/ 03DESIGNATOR,LOCATION,CONTACT TO CONTACT CONTACT TO CONTACT LOCATION DESIGNATOR A DESIGNATION WHICH IS USED TO INDICATE ONE FIXED CONTACT POSITION AND THE OPPOSITE FIXED CONTACT POSITION OF A POLARIZING KEY. 1A MODE REPLY 0 CRNDJ /D/ 04ANGLE,INCLUDED,INSIDE INSIDE INCLUDED ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CRNFB /D/ 04ANGLE IN DEG,CHAMFER,THIRD OUTSIDE CORNER THIRD OUTSIDE CORNER CHAMFER ANGLE IN DEG NONE. REPLACED BY MRC AATE WITH ISAC 0368. 1B MODE REPLY 0 CRNGJ A19ARRANGEMENT,CONTACT,MAIN,NONPILE-UP NONPILE-UP MAIN CONTACT ARRANGEMENT THE DESIGNATION THAT IDENTIFIES THE SCHEMATIC DIAGRAM OF THE ELECTRICAL CONFIGURATION OF THE MAIN NONPILE-UP CONTACTS INCLUDING THE NUMBER OF POLES OR FORMS. 1D AND 1A MODE REPLY12AG28 CRNHJ 04DISTANCE FROM INSIDE FLATTED PORTION TO OPPOSITE SURFACE DISTANCE FROM INSIDE FLATTED PORTION TO OPPOSITE SURFACE NONE. 2D AND 1B MODE REPLY21AA051AC20 CRNJD 19GRADE,CORE CORE GRADE AN INDICATION OF THE GRADE OF THE CORE. SELECT REPLY CODE 10AP02 CRNKJ 04DIAMETER,GROOVE,MINOR MINOR GROOVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRNLJ A18TYPE,TERMINAL,NONFEEDTHRU NONFEEDTHRU TERMINAL TYPE INDICATES THE TYPE OF NONFEEDTHRU TERMINAL FURNISHED WITH THE ITEM. 1D AND 1A MODE REPLY12AK17 CRNMJ 10RESISTANCE AT 25 DEG CELSIUS,INSULATION INSULATION RESISTANCE AT 25 DEG CELSIUS DIRECT CURRENT RESISTANCE BETWEEN TWO CONDUCTORS THAT ARE SEPARATED BY AN INSULATING MATERIAL,MEASURED AT 25 DEGREES CELSIUS. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 1D AND 1B MODE REPLY12AN86 CRNNJ 04DIAMETER,HOLE,EJECTOR SPRING EJECTOR SPRING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRNPD 19DEGREE,BLACKOUT BLACKOUT DEGREE AN INDICATION OF THE DEGREE OF BLACKOUT AFFORDED. SELECT REPLY CODE 10AD33 CRNQJ 04ANGLE IN DEG,BEVEL,CLIP CLIP BEVEL ANGLE IN DEG NONE. 1D AND 1B MODE REPLY11AC20 CRNRJ 04DISTANCE FROM PIN HOLE CENTER TO EDGE DISTANCE FROM PIN HOLE CENTER TO EDGE NONE. 2D AND 1B MODE REPLY21AA051AC20 CRNSJ /D/A13THREAD QUANTITY PER INCH-LOCATION AND PUMP DESIGNATION THREAD QUANTITY PER INCH-LOCATION AND PUMP DESIGNATION THE NUMBER OF THREADS ON THE ITEM PER INCH,ITS LOCATION,AND THE PUMP DESIGNATION. 2D AND 1A MODE REPLY23AN733AA96 CRNTA /D/ 13THREAD TOLERANCE CLASS,COUNTERBORE COUNTERBORE THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITIONS AND GRADES OF A COUNTERBORE THREAD. 1A MODE REPLY 0 CRNWJ 04LENGTH,OVERALL,FIRST BRUSH FIRST BRUSH OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRNXJ /D/ 04ANGLE,FLOW FLOW ANGLE THE ANGLE THE FLOW IS TURNED FROM THE STRAIGHT FLOW. 2D AND 1B MODE REPLY21AP381AC20 CRNYJ /D/A13THREAD QUANTITY,CONDUCTOR ACCOMMODATION CONDUCTOR ACCOMMODATION THREAD QUANTITY THE NUMBER OF THREADS ON THE CONDUCTOR ACCOMMODATION,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1D AND 1A MODE REPLY11AB39 CRNZB 13THREAD PITCH IN MILLIMETERS,HOLE,MOUNTING MOUNTING HOLE THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT MOUNTING HOLE THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CRPBJ /D/ 04WIDTH,SURFACE,RING BEARING RING BEARING SURFACE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRPCD /D/ 18TYPE,RECEPTACLE,CABLE CABLE RECEPTACLE TYPE INDICATES THE TYPE OF CABLE RECEPTACLES INCLUDED ON THE ITEM. SELECT REPLY CODE 10AC50 CRPDJ 04DIAMETER,HOLE,STUD MOUNTING STUD MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRPFD 13THREAD SERIES DESIGNATOR,END,SECOND SECOND END THREAD SERIES DESIGNATOR A DESIGNATOR DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CRPGJ A13THREAD CLASS AND LOCATION THREAD CLASS AND LOCATION A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD AND THE LOCATION. 1D AND 1A MODE REPLY13AN73 CRPHJ 04DISTANCE,OUTER EDGE TO SLOT EDGE OUTER EDGE TO SLOT EDGE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CRPJJ 04DIAMETER,OUTSIDE,SKIRT SKIRT OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRPKJ 10PRESSURE RATING AND SERVICE FOR WHICH DESIGNED,WORKING,MAXIMUM MAXIMUM WORKING PRESSURE RATING AND SERVICE FOR WHICH DESIGNED THE MAXIMUM RATED WORKING PRESSURE THE ITEM CAN WITHSTAND WITHOUT RUPTURE,AND THE SERVICE FOR WHICH DESIGNED. 2D AND 1B MODE REPLY22AG673AA94 CRPLJ /D/ 04DIAMETER,CIRCLE,OUTER TERMINAL OUTER TERMINAL CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRPMJ /D/ 04DIAMETER,INSIDE,THIMBLE THIMBLE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRPND /D/ 07WRAPPED,INDIVIDUALLY INDIVIDUALLY WRAPPED AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED INDIVIDUAL WRAPPING. SELECT REPLY CODE 10AB22 CRPPJ 10COMPOSITION IN PERCENT,CHEMICAL,FILLER METAL FILLER METAL CHEMICAL COMPOSITION IN PERCENT AN INDICATION OF THE PROPORTION OF THE ELEMENT(S) OF THE FILLER METAL,EXPRESSED IN PERCENT. 2D AND 1B MODE REPLY23AN411AC20 CRPQJ 10CURRENT RATING AND TYPE,OPERATING,NOMINAL NOMINAL OPERATING CURRENT RATING AND TYPE THE REQUIRED CURRENT VALUE,APPLIED TO THE ENERGIZING ELEMENT,AT WHICH THE SWITCHING MECHANISM OR ACTUATOR ELEMENT MUST HAVE ASSUMED A FULLY OPERATED POSITION. 2D AND 1B MODE REPLY22AN862AN87 CRPRJ 04DISTANCE,CENTER,SECOND SECOND CENTER DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CRPSL 16STYLE,BASE BASE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BASE. 1L MODE REPLY 0 CRPTJ 04LENGTH,SHANK,FASTENER FASTENER SHANK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRPWJ /D/ 04WIDTH-LOCATION AND MEASURING METHOD WIDTH-LOCATION AND MEASURING METHOD A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS,ITS LOCATION ON THE ITEM,AND THE MEASURING METHOD USED. PLEASE USE MRC CRXX WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC. 4D AND 1B MODE REPLY41AA051AC203AN732AN68 CRPXJ 04DIAMETER FROM HEAD,EIGHTH EIGHTH DIAMETER FROM HEAD NONE. 2D AND 1B MODE REPLY21AA051AC20 CRPYL 16STYLE,ARRANGEMENT,CONTACT POSITION CONTACT POSITION ARRANGEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE CONTACT POSITIONS. 1L MODE REPLY 0 CRPZD 19CONDITION,SURFACE,OVERALL OVERALL SURFACE CONDITION THE OVERALL CONDITION OF THE ITEM WITH RESPECT TO THE TEXTURE OF THE SURFACE. SELECT REPLY CODE 10AN72 CRQBJ 04LENGTH,OVERALL,SECOND BRUSH SECOND BRUSH OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRQCJ 04ANGLE,BEND,TERMINAL TERMINAL BEND ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CRQDJ 04DISTANCE,SHOULDER TO HEAD END SHOULDER TO HEAD END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CRQFD 02DESIGN,BODY,GARMENT GARMENT BODY DESIGN THE BODY DESIGN OF THE GARMENT. SELECT REPLY CODE 10AF68 CRQGD 18TYPE,LENS LENS TYPE INDICATES THE TYPE OF LENS PROVIDED. SELECT REPLY CODE 10AP19 CRQHJ /D/ 04SIZE,CROSS SECTION,LARGEST LARGEST CROSS SECTION SIZE NONE. 2D AND 1B MODE REPLY21AA051AC20 CRQJF T10TOLERANCE IN PERCENT AT REFERENCE TEMP,RESISTANCE,ZERO POWER ZERO POWER RESISTANCE TOLERANCE IN PERCENT AT REFERENCE TEMP THE LIMITS OF PERMISSIBLE VARIATION IN THE ELECTRICAL RESISTANCE VALUE OF AN ITEM FROM ITS RATED ZERO POWER RESISTANCE,EXPRESSED IN PERCENT AT REFERENCE TEMPERATURE. 1F MODE REPLY 0 CRQKA /D/ 13THREAD QUANTITY PER INCH,HOLE,CONCENTRIC CONCENTRIC HOLE THREAD QUANTITY PER INCH THE NUMBER OF CONCENTRIC HOLE THREADS PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CRQLJ /D/ 10TORQUE,BREAKAWAY,MECHANICAL MECHANICAL BREAKAWAY TORQUE THE AMOUNT OF ROTARY FORCE REQUIRED TO JUST TURN THE ROTOR FROM REST WHEN NOT ENERGIZED. 2D AND 1B MODE REPLY21AA561AC20 CRQMJ /D/ 04DISTANCE,CENTER TO CENTER,BEND BEND CENTER TO CENTER DISTANCE THE CENTER TO CENTER DISTANCE FROM THE OPENING AT ONE END TO THE OPENING AT THE OPPOSITE END. 2D AND 1B MODE REPLY21AA051AC20 CRQNJ 10LEAKAGE AT 25 DEG CELSIUS,DC DC LEAKAGE AT 25 DEG CELSIUS STRAY DIRECT CURRENT OF RELATIVELY SMALL VALUE WHICH FLOWS THROUGH THE CAPACITOR WHEN VOLTAGE IS IMPRESSED ACROSS IT,MEASURED AT 25 DEGREES CELSIUS. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 1D AND 1B MODE REPLY12AN86 CRQPJ /D/ 04LENGTH,SHANK,PUSH BUTTON SOCKET PUSH BUTTON SOCKET SHANK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRQQJ /D/ 04DIAMETER,BORE,BEARING BEARING BORE DIAMETER NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 CRQRJ A18TYPE ACCOMMODATED AND SIZE DESIGNATION,CLOSURE CLOSURE TYPE ACCOMMODATED AND SIZE DESIGNATION INDICATES THE TYPE OF CLOSURE THE ITEM WILL ACCOMMODATE AND THE SIZE DESIGNATION. 1D AND 1A MODE REPLY13AM35 CRQSA /D/ 03DESIGNATOR,CLASS,DISCHARGE LAMP DISCHARGE LAMP CLASS DESIGNATOR A DESIGNATION WHICH GIVES,IN CODE FORM,THE CLASSIFICATION OF A DISCHARGE LAMP. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1A MODE REPLY 0 CRQTJ 04DISTANCE BETWEEN CONDUCTOR GROOVE AND MOUNTING HOLE DISTANCE BETWEEN CONDUCTOR GROOVE AND MOUNTING HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 CRQWJ /D/ 04DIAMETER,OUTSIDE,SMALLEST,RING RING SMALLEST OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRQXJ A08LOCATION AND QUANTITY,HOLE,CLEANING CLEANING HOLE LOCATION AND QUANTITY INDICATES THE LOCATION AND NUMBER OF CLEANING HOLES INCLUDED IN THE ITEM. 1D AND 1A MODE REPLY13AN73 CRQYJ A18TYPE AND QUANTITY,FACILITY,MOUNTING,COMPONENT COMPONENT MOUNTING FACILITY TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF FACILITIES PROVIDED FOR MOUNTING THE COMPONENT/S/. 1D AND 1A MODE REPLY12AB21 CRQZJ A14SHAPE AND QUANTITY,OPENING,COVER COVER OPENING SHAPE AND QUANTITY THE PHYSICAL CONFIGURATION AND NUMBER OF OPENINGS INCLUDED IN THE COVER. 1D AND 1A MODE REPLY13AP00 CRRBJ 04ANGLE,SEAT SEAT ANGLE THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS. 2D AND 1B MODE REPLY21AP381AC20 CRRCD 18TYPE,STYLE STYLE TYPE INDICATES THE TYPE OF DESIGN THAT INDICATES THE STYLE OF THE ITEM. SELECT REPLY CODE 10AP54 CRRDJ /D/ 04DISTANCE FROM BRUSH TOP TO UNDERCUT DISTANCE FROM BRUSH TOP TO UNDERCUT NONE. 2D AND 1B MODE REPLY21AA051AC20 CRRFJ A18TYPE AND QUANTITY,WHEEL WHEEL TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF WHEELS INCLUDED ON THE ITEM. 1D AND 1A MODE REPLY12AH67 CRRGJ 04DIAMETER,HEAD,PIN PIN HEAD DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRRHJ 04WIDTH,NOMINAL,CUT CUT NOMINAL WIDTH A NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CUT,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CRRJD 18TYPE,CONSTRUCTION,TOE TOE CONSTRUCTION TYPE INDICATES THE TYPE OF CONSTRUCTION OF THE UPPER FORE PART OF THE ITEM. SELECT REPLY CODE 10AK55 CRRKJ /D/ 13THREAD SIZE,NOMINAL,HEEL INLET HEEL INLET NOMINAL THREAD SIZE NONE. 1D AND 1B MODE REPLY11AA05 CRRLD 18TYPE,MECHANISM,POSITIONING POSITIONING MECHANISM TYPE INDICATES THE TYPE OF MECHANISM USED FOR POSITIONING THE ITEM. SELECT REPLY CODE 10AJ12 CRRMJ 10FORCE,RELEASE,SWITCH SWITCH RELEASE FORCE THE AMOUNT TO WHICH THE ACTUATING FORCE MUST BE REDUCED TO PERMIT THE SWITCH TO BECOME UNACTUATED. 2D AND 1B MODE REPLY21AA561AC20 CRRNJ /D/ 10TEMPERATURE RATING AND DESIGNATION,STEAM,PRIME MOVER PRIME MOVER STEAM TEMPERATURE RATING AND DESIGNATION THE RATED TEMPERATURE OF THE STEAM NECESSARY TO OPERATE THE PRIME MOVER AT FULL CAPACITY,AND ITS DESIGNATION. 2D AND 1B MODE REPLY21AB361AP23 CRRPJ 04DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF SEVENTH DIAMETER DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF SEVENTH DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRRRH /D/ 09MATERIAL AND LOCATION,COATING COATING MATERIAL AND LOCATION THE COATING MATERIAL AND DESIGNATION OF THAT PART OF THE ITEM TO WHICH A COATING HAS BEEN APPLIED,EXCLUDING ANY SURFACE TREATMENT. 2D MODE REPLY 23AN736AD09 CRRSJ 04WIDTH,HOLE,SECOND SECOND HOLE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRRTJ /D/ 04WIDTH,FLANGE,SLEEVE SLEEVE FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRRWJ A18TYPE AND QUANTITY,GAIN GAIN TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF GAINS PROVIDED ON THE ITEM. 1D AND 1A MODE REPLY13AK54 CRRXJ /D/ 04LENGTH,TERMINAL,SECOND END SECOND END TERMINAL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRRYJ /D/ 04DIAMETER,OUTSIDE,BEARING SEATING RING BEARING SEATING RING OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRRZJ 04DIAMETER,HOLE,TERMINAL WIRE TERMINAL WIRE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRSBJ 04ANGLE,OUTSIDE,LEFT LEFT OUTSIDE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CRSCJ /D/ 10CURRENT RATING AND TYPE PER POLE IN AMPS,INTERRUPTING,MAXIMUM MAXIMUM INTERRUPTING CURRENT RATING AND TYPE PER POLE IN AMPS THE MAXIMUM RATED VALUE AND THE CURRENT TYPE THAT WILL CAUSE INTERRUPTION AT EACH POLE,EXPRESSED IN AMPERES. 2D AND 1B MODE REPLY22AN872AP31 CRSDJ 04ANGLE,RECESS,TOP TOP RECESS ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CRSFJ /D/ 04LENGTH,OVERALL,THIRD BRUSH THIRD BRUSH OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRSGJ 04HEIGHT,OVERALL,LOCKSPRING LOCKSPRING OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CRSHJ /D/ 04DISTANCE BETWEEN MOUNTING AND FIRST TURRET DISTANCE BETWEEN MOUNTING AND FIRST TURRET NONE. 2D AND 1B MODE REPLY21AA051AC20 CRSJD 18TYPE,SHAFT SHAFT TYPE INDICATES THE TYPE OF SHAFT INCLUDED ON THE ITEM. SELECT REPLY CODE 10AF58 CRSKL 16STYLE,BULB BULB STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BULB. 1L MODE REPLY 0 CRSLB /D/ 04TAPER PER METER IN MILLIMETERS,RING,OUTER OUTER RING TAPER PER METER IN MILLIMETERS NONE. 1B MODE REPLY 0 CRSMB 10VACUUM IN TORR VACUUM IN TORR THE ULTIMATE MAXIMUM VACUUM,EXPRESSED IN TERMS OF ABSOLUTE PRESSURE,THAT MAY BE PRODUCED BY OR APPLIED TO AN ITEM. 1B MODE REPLY 0 CRSNJ A18TYPE AND QUANTITY,WEAPON,ATTACHED ATTACHED WEAPON TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF INDIVIDUAL WEAPON/S/ ATTACHED TO THE ITEM. 1D AND 1A MODE REPLY13AF49 CRSPJ /D/ 10LIFT RATING AND PUMP DESIGNATION,SUCTION SUCTION LIFT RATING AND PUMP DESIGNATION THE VERTICAL DISTANCE AN ITEM IS RATED TO LIFT THE MEDIA,AND THE PUMP DESIGNATION. 2D AND 1B MODE REPLY21AA053AA96 CRSQJ 04ANGLE,COUNTERSINK COUNTERSINK ANGLE THE INCLUDED ANGLE OF THE COUNTERSINK. 2D AND 1B MODE REPLY21AP381AC20 CRSRJ /D/ 10VOLTAGE RATING IN KILOVOLTS,WITHSTANDING,DIELECTRIC DIELECTRIC WITHSTANDING VOLTAGE RATING IN KILOVOLTS THE MAXIMUM RATED VOLTAGE THAT THE ITEM WILL WITHSTAND WITHOUT ARCING,FLASHOVER,BREAKDOWN OF INSULATION,OR OTHER PHYSICAL DAMAGE,EXPRESSED IN KILOVOLTS. 1D AND 1B MODE REPLY11AB62 CRSSJ T10TOLERANCE PER SECTION IN PERCENT,RESISTANCE RESISTANCE TOLERANCE PER SECTION IN PERCENT THE LIMITS OF PERMISSIBLE VARIATION IN THE ELECTRICAL RESISTANCE VALUE PER SECTION OF AN ITEM FROM ITS RATED VALUE,EXPRESSED IN PERCENT. 1D AND 1F MODE REPLY12AH19 CRSTD 17SURFACE TREATMENT,BODY BODY SURFACE TREATMENT THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE BODY IS PLATED,DIPPED AND/OR COATED. THE TREATMENT IS DESIGNED TO PROTECT THE BODY SURFACE/S/ AND CANNOT BE WIPED OFF. SELECT REPLY CODE 10SF01 CRSWJ 04LENGTH,GRIP,PIN PIN GRIP LENGTH THE DISTANCE MEASURED ON A LINE PARALLEL TO THE LONGITUDINAL AXIS WHICH DETERMINES THE GRIPPING LENGTH OF THE PIN. 2D AND 1B MODE REPLY21AA051AC20 CRSXD 19FEATURE,CONTROL,ACTUATOR TRAVEL ACTUATOR TRAVEL CONTROL FEATURE THE FEATURE THAT CONTROLS THE ACTUATOR TRAVEL. SELECT REPLY CODE 10AN94 CRSYJ 04DEPTH,HOLE,ALIGNMENT ALIGNMENT HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRSZJ /D/ 04LENGTH AND POSITION,OVERALL,LENS LENS OVERALL LENGTH AND POSITION NONE. 3D AND 1B MODE REPLY31AA051AC202AK17 CRTBJ 10SPACING,HOLE,THIRD THIRD HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 CRTCA 02DESIGN,STRIP,TERMINAL TERMINAL STRIP DESIGN THE SHAPE AND ARRANGEMENT OF THE TERMINAL/S/ AND MOUNTING FOOT /FEET/ AND/OR HOLE/S/. 1A MODE REPLY 0 CRTDD 13THREAD SERIES DESIGNATOR,INLET INLET THREAD SERIES DESIGNATOR A DESIGNATOR DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CRTFD 19FUNCTION FOR WHICH DESIGNED,KEY KEY FUNCTION FOR WHICH DESIGNED THE PURPOSE FOR WHICH THE KEY IS DESIGNED. SELECT REPLY CODE 10AP43 CRTGD /D/ 07ADJUSTABILITY,POINT,CONTACT DEACTUATION CONTACT DEACTUATION POINT ADJUSTABILITY AN INDICATION OF THE ADJUSTABILITY OF THE CONTACT DEACTUATION POINT. SELECT REPLY CODE 10AC06 CRTHJ 10SPACING,HOLE,EIGHTH EIGHTH HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 CRTJD 19SUBSTANCE,IMPREGNATION IMPREGNATION SUBSTANCE THE SUBSTANCE USED TO SATURATE THE ITEM. SELECT REPLY CODE 10AG56 CRTKD 18TYPE,TERMINAL,SWITCH SWITCH TERMINAL TYPE INDICATES THE TYPE OF TERMINAL FOR PROVIDING ELECTRICAL CONNECTION TO THE SWITCH. SELECT REPLY CODE 10AN89 CRTLA 15CRITICALITY CODE JUSTIFICATION CRITICALITY CODE JUSTIFICATION THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM. 1A MODE REPLY 0 CRTMD 18TYPE,SURFACE,BEARING BEARING SURFACE TYPE INDICATES THE TYPE OF BEARING SURFACE. SELECT REPLY CODE 10AB80 CRTNJ A19STRENGTH,TIRE TIRE STRENGTH AN INDICATION OF THE STRENGTH /LOAD LIMITS/ OF A TIRE. 1D AND 1A MODE REPLY11AN81 CRTPJ T10RANGE PER SECTION,TOLERANCE TOLERANCE RANGE PER SECTION THE LIMITS OF PERMISSIBLE DEVIATION PER SECTION OF A MEASURED VALUE FROM A SPECIFIED VALUE. 2D AND 1F MODE REPLY22AN862AH19 CRTQJ /D/T13THREAD PITCH DIAMETERS,NONSTANDARD,CONCENTRIC HOLE CONCENTRIC HOLE NONSTANDARD THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A CONCENTRIC HOLE NONSTANDARD STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 CRTRJ /D/A10STRENGTH,TENSILE,PULLEY SURFACE PULLEY SURFACE TENSILE STRENGTH THE MAXIMUM LOAD IN TENSION APPLIED IN A LONGITUDINAL DIRECTION,PER UNIT OF CROSS-SECTIONAL AREA,THAT THE PULLEY SURFACE CAN WITHSTAND WITHOUT RUPTURE. 2D AND 1A MODE REPLY21AN711AC20 CRTSJ /D/ 04DIAMETER,CARTRIDGE CARTRIDGE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CARTRIDGE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CRTTJ 04DEPTH,SHOULDER SHOULDER DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRTWJ 04DISTANCE FROM INSIDE OF MOUNTING HOLE TO OUTSIDE SURFACE DISTANCE FROM INSIDE OF MOUNTING HOLE TO OUTSIDE SURFACE NONE. 2D AND 1B MODE REPLY21AA051AC20 CRTXJ /D/ 13THREAD SIZE-LOCATION AND PUMP DESIGNATION,NOMINAL NOMINAL THREAD SIZE-LOCATION AND PUMP DESIGNATION A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD,ITS LOCATION ON THE ITEM,AND THE PUMP DESIGNATION. 3D AND 1B MODE REPLY31AA053AN733AA96 CRTYJ 04SIZE,SHAFT,SQUARE SQUARE SHAFT SIZE NONE. 2D AND 1B MODE REPLY21AA051AC20 CRTZJ 04WIDTH,HOLE,PLATE PLATE HOLE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRWBJ 13THREAD SIZE AND LOCATION,NOMINAL NOMINAL THREAD SIZE AND LOCATION A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD AND THE LOCATION. 2D AND 1B MODE REPLY21AA053AN73 CRWCJ 04RADIUS,GROOVE,TOP WIRE TOP WIRE GROOVE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CRWDJ T10RANGE RATING,TEMP,EFFECTIVE EFFECTIVE TEMP RANGE RATING THE MINIMUM AND MAXIMUM EFFECTIVE TEMPERATURE RATING OF THE ITEM. 1D AND 1F MODE REPLY11AB36 CRWFJ A19DEVICE AND QUANTITY,PROTECTIVE,THREAD THREAD PROTECTIVE DEVICE AND QUANTITY AN ITEM APPLIED TO THE THREADED END OF AN ITEM TO GUARD AGAINST DAMAGE DURING SHIPPING,STORAGE,AND HANDLING,AND THE NUMBER PROVIDED. 1D AND 1A MODE REPLY11AN77 CRWGL 16STYLE,BRACKET,MOUNTING MOUNTING BRACKET STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE MOUNTING BRACKET. 1L MODE REPLY 0 CRWHJ 10TEMP AND MEDIA FOR WHICH DESIGNED,OPERATING,MAXIMUM MAXIMUM OPERATING TEMP AND MEDIA FOR WHICH DESIGNED A RATING WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AS APPLIED TO THE OPERATION,OR LIMITATION OF OPERATION,FOR EACH TYPE OF SERVICE WITH WHICH AN ITEM MAY BE USED. 2D AND 1B MODE REPLY21AB363AN91 CRWJD 08LOCATION,OUTLET OUTLET LOCATION INDICATES THE LOCATION OF THE OUTLET ON THE ITEM. SELECT REPLY CODE 10AN73 CRWKJ 04RADIUS,SIDE,FIRST FIRST SIDE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CRWLD 19CONDITION,SURFACE,INSIDE INSIDE SURFACE CONDITION THE CONDITION OF THE ITEM WITH RESPECT TO THE TEXTURE OF THE INNER SURFACE. SELECT REPLY CODE 10AN72 CRWMJ 04DIAMETER,OUTSIDE,CONNECTING ARM CONNECTING ARM OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRWNJ 04DISTANCE FROM CONDUCTOR SLOT TO OPPOSITE SURFACE,FIRST FIRST DISTANCE FROM CONDUCTOR SLOT TO OPPOSITE SURFACE NONE. 2D AND 1B MODE REPLY21AA051AC20 CRWPB /D/ 04TAPER PER METER IN MILLIMETERS,CONE CONE TAPER PER METER IN MILLIMETERS NONE. 1B MODE REPLY 0 CRWQJ A18TYPE AND QUANTITY,SPRING,PRESSURE PRESSURE SPRING TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF PRESSURE SPRINGS PROVIDED. 1D AND 1A MODE REPLY11AA21 CRWRJ /D/ 10STIMULUS RATING,POINT,CONTACT DEACTUATION CONTACT DEACTUATION POINT STIMULUS RATING THE VALUE OF THE STIMULUS AT WHICH THE CONTACTS DEACTUATE. 2D AND 1B MODE REPLY22AG201AC20 CRWSJ /D/ 04DISTANCE BETWEEN MOUNTING FACILITY BOTTOM AND CONDUCTOR ACCOMMODATION CENTERLINE,OFFSET OFFSET DISTANCE BETWEEN MOUNTING FACILITY BOTTOM AND CONDUCTOR ACCOMMODATION CENTERLINE NONE. 2D AND 1B MODE REPLY21AA051AC20 CRWTH /D/ 18TYPE,FUNCTION AND EMISSION FUNCTION AND EMISSION TYPE A FUNCTION OF THE ITEM,AND A CLASSIFICATION OF RADIO FREQUENCY EMISSIONS IN WHICH THE MODULATION,TRANSMISSION,AND/OR SUPPLEMENTARY CHARACTERISTICS ARE REPRESENTED BY SYMBOLS. 2D MODE REPLY 22AK273AP28 CRWWB 10PERCENTAGE BY VOLUME,AROMATICS,MAXIMUM MAXIMUM AROMATICS PERCENTAGE BY VOLUME A MEASUREMENT OF THE MAXIMUM AROMATICS OCCURING IN THE ITEM,EXPRESSED IN PERCENT BY VOLUME. 1B MODE REPLY 0 CRWXD 02DESIGN,SKIRT SKIRT DESIGN INDICATES WHETHER OR NOT THE SKIRT IS DESIGNED AS AN INTEGRAL PART OF THE ITEM. SELECT REPLY CODE 10AH97 CRWYD 14SHAPE,SURFACE,WRENCHING WRENCHING SURFACE SHAPE THE GEOMETRIC CONFIGURATION OF THE WRENCHING SURFACE OF THE ITEM. SELECT REPLY CODE 10AP00 CRWZA 10PERCENTAGE AT MAXIMUM TEMP,POINT,DISTILLATION DISTILLATION POINT PERCENTAGE AT MAXIMUM TEMP AN INDICATION OF THE MAXIMUM TEMPERATURE AT WHICH A CERTAIN DISTILLATION POINT IS REACHED,EXPRESSED IN PERCENT. 1A MODE REPLY 0 CRXBJ 04DIAMETER,HOLE,STUD SHANK STUD SHANK HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRXCJ /D/ 04WIDTH ACROSS FLATS,BUSHING,THREADED THREADED BUSHING WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 CRXDJ 04DIAMETER,MINOR,TAPERED BRUSH PART,SINGLE BRUSH SINGLE BRUSH TAPERED BRUSH PART MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRXFJ /D/ 04THICKNESS,SHOULDER,SECONDARY WASHER SECONDARY WASHER SHOULDER THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CRXGJ /D/ 04SPACING,HOLE,SIXTH MOUNTING SIXTH MOUNTING HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 CRXHJ 10DELAY,TIME TIME DELAY THE INTERVAL FOR WHICH THE ITEM,BY DESIGN,IS PURPOSELY DELAYED BETWEEN INTRODUCTION OF POWER INTO THE ENERGIZING ELEMENT AND COMPLETION OF TRAVEL OF THE CONTACT CARRIER,AND/OR BETWEEN INTERRUPTION OF THE ENERGIZING POWER AND RETURN OF THE CONTACT CARRIER TO ITS NORMAL DE-ENERGIZING POSITION. 2D AND 1B MODE REPLY22AH681AC20 CRXJJ 04RADIUS,TIP,FIRST END FIRST END TIP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CRXKB /D/ 13THREAD PITCH IN MILLIMETERS,COUNTERBORE COUNTERBORE THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE COUNTERBORE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CRXLJ A12QUANTITY PER SECONDARY CONTAINER,PRIMARY CONTAINER PRIMARY CONTAINER QUANTITY PER SECONDARY CONTAINER THE NUMBER OF PRIMARY CONTAINERS WITHIN EACH SECONDARY CONTAINER. 1D AND 1A MODE REPLY13AN65 CRXMJ /D/ 04DIAMETER,OUTSIDE,SMALLEST,CUP CUP SMALLEST OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRXPJ 04LENGTH,LEG,HORIZONTAL HORIZONTAL LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRXQJ 04DEPTH,HOLE,NONTURN FEATURE NONTURN FEATURE HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRXRJ A18TYPE AND QUANTITY,TERMINAL,GROUND GROUND TERMINAL TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF GROUND TERMINALS FOR PROVIDING ELECTRICAL CONNECTION. 1D AND 1A MODE REPLY13AN89 CRXSJ 04DEPTH,OVERALL,STUD STUD OVERALL DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRXTJ 04HEIGHT,HOLE,PANEL ACCOMMODATION PANEL ACCOMMODATION HOLE HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE PANEL OPENING FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 CRXWD 02DESIGN,MEDIA,FILTERING FILTERING MEDIA DESIGN AN INDICATION OF THE STRUCTURE OR CHARACTERISTIC OF THE FILTERING MEDIA. SELECT REPLY CODE 10AC48 CRXXJ 11METHOD AND LENGTH,MEASURING MEASURING METHOD AND LENGTH THE MEANS USED AND THE MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM. 3D AND 1B MODE REPLY31AA051AC202AN68 CRXYJ 10PERCENTAGE BY WEIGHT AND TEST METHOD,CONTENT,MAXIMUM CARBON RESIDUE MAXIMUM CARBON RESIDUE CONTENT PERCENTAGE BY WEIGHT AND TEST METHOD A MEASUREMENT OF THE MAXIMUM CARBON RESIDUE CONTENT,EXPRESSED IN PERCENT BY WEIGHT,AND THE TEST METHOD. 1D AND 1B MODE REPLY13AJ50 CRXZD 18TYPE,CONNECTION,FIRST INTAKE FIRST INTAKE CONNECTION TYPE INDICATES THE TYPE OF CONNECTION ON THE FIRST INTAKE. SELECT REPLY CODE 10AB76 CRYBD 07ADJUSTABILITY,STRAP,CHEST CHEST STRAP ADJUSTABILITY AN INDICATION OF WHETHER OR NOT THE CHEST STRAP IS ADJUSTABLE. SELECT REPLY CODE 10AB00 CRYCD 19CLASSIFICATION,SUBSTANCE,CONTROLLED CONTROLLED SUBSTANCE CLASSIFICATION DRUGS OR SUBSTANCES SUBJECT TO THE PROVISIONS OF THE COMPREHENSIVE DRUG ABUSE PREVENTION AND CONTROL ACT OF 1970. SELECT REPLY CODE 10AP11 CRYDA 10PERIOD IN MONTHS,DATING,EXPIRATION EXPIRATION DATING PERIOD IN MONTHS REPRESENTS THE PERIOD BEYOND WHICH THE POTENCY OF THE DRUG CANNOT BE EXPECTED,BEYOND REASONABLE DOUBT,TO REMAIN EFFECTIVE THERAPEUTICALLY,OR RETAIN ITS REQUIRED POTENCY,EXPRESSED IN MONTHS. 1A MODE REPLY 0 CRYFD 02DESIGN,PREPRINTED PREPRINTED DESIGN THE DESIGN OR SYMBOL PREPRINTED ON THE ITEM. SELECT REPLY CODE 10AH39 CRYGJ 04ANGLE BETWEEN FIFTH AND SIXTH KEY ANGLE BETWEEN FIFTH AND SIXTH KEY NONE. 2D AND 1B MODE REPLY21AP381AC20 CRYHJ /D/A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,FACILITY,MOUNTING COVER MOUNTING COVER FACILITY THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND THE NUMBER OF THREADS PER MEASUREMENT SCALE OF THE COVER MOUNTING FACILITY. 1D AND 1A MODE REPLY12AH06 CRYJH /D/ 19MEDIA FOR WHICH DESIGNED AND PUMP DESIGNATION MEDIA FOR WHICH DESIGNED AND PUMP DESIGNATION THE LIQUID OR GAS FOR WHICH AN ITEM IS DESIGNED,AND THE PUMP DESIGNATION. 2D MODE REPLY 23AN913AA96 CRYKD 18TYPE,HOLE,PANEL MOUNTING RAIL PANEL MOUNTING RAIL HOLE TYPE INDICATES THE TYPE OF HOLES PROVIDED IN THE PANEL MOUNTING RAIL. SELECT REPLY CODE 10AB68 CRYLJ /D/ 04LENGTH,MINOR,BUSHING BUSHING MINOR LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRYMD /D/ 07ADJUSTABILITY,POINT,CONTACT ACTUATION CONTACT ACTUATION POINT ADJUSTABILITY AN INDICATION OF THE ADJUSTABILITY OF THE CONTACT ACTUATION POINT. SELECT REPLY CODE 10AC06 CRYNJ 10SPACING,HOLE,FIFTH FIFTH HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 CRYPJ /D/ 04ANGLE,SECTOR,STUD STUD SECTOR ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CRYQD 19DEGREE,CONDITION,SURFACE SURFACE CONDITION DEGREE THE EXTENT OF SURFACE DRESSING OR ROUGHNESS OF THE ITEM. SELECT REPLY CODE 10AP06 CRYRJ /D/ 04DIAMETER,MAJOR,PLUG PLUG MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRYSJ /D/ 04DIAMETER,BORE,RING RING BORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CRYTL 16STYLE,WASHER,SECONDARY SECONDARY WASHER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SECONDARY WASHER. 1L MODE REPLY 0 CRYWJ 04DISTANCE FROM MOUNTING HOLE CENTER TO END DISTANCE FROM MOUNTING HOLE CENTER TO END THE DISTANCE FROM THE CENTER OF THE MOUNTING HOLE TO THE END OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CRYXJ 04ANGLE,INNER FACE TO OUTER FACE,LEFT TOP LEFT TOP INNER FACE TO OUTER FACE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CRYYJ 13SCREW THREAD DIAMETER,NOMINAL,MOUNTING FACILITY MOUNTING FACILITY NOMINAL SCREW THREAD DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COAXIAL CYLINDER WHICH WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD. 1D AND 1B MODE REPLY11AA05 CRYZJ 04DEPTH,SLOT,FIRST FIRST SLOT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRZBJ /D/ 04RADIUS,CORNER,INTERNAL CONE INTERNAL CONE CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CRZCJ 04ANGLE,INSIDE,RIGHT TOP RIGHT TOP INSIDE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CRZDD 19RELATIONSHIP TO FIRST INTAKE CONNECTION,CONNECTION,SECOND INTAKE SECOND INTAKE CONNECTION RELATIONSHIP TO FIRST INTAKE CONNECTION THE SECOND INTAKE CONNECTION RELATIONSHIP TO THE FIRST INTAKE CONNECTION. SELECT REPLY CODE 10AB78 CRZFJ 04DISTANCE FROM END OF STUD END THREADS TO NUT END DISTANCE FROM END OF STUD END THREADS TO NUT END NONE. 2D AND 1B MODE REPLY21AA051AC20 CRZGJ 04THICKNESS,OVERALL,NOMINAL NOMINAL OVERALL THICKNESS AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 CRZHD 18TYPE,CONNECTION,SECOND INTAKE SECOND INTAKE CONNECTION TYPE INDICATES THE TYPE OF CONNECTION ON THE SECOND INTAKE. SELECT REPLY CODE 10AB76 CRZJD /D/ 19POSITION RELATIVE TO THE MOUNTING POSITION,ACCOMMODATION,CONDUCTOR CONDUCTOR ACCOMMODATION POSITION RELATIVE TO THE MOUNTING POSITION THE POSITION OF THE CONDUCTOR ACCOMMODATION IN RELATION TO THE MOUNTING FACILITY. SELECT REPLY CODE 10AP08 CRZKJ /D/ 04DIAMETER,OUTSIDE,MINIMUM MINIMUM OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CRZLJ 04ANGLE BETWEEN FIRST AND SECOND KEY ANGLE BETWEEN FIRST AND SECOND KEY NONE. 2D AND 1B MODE REPLY21AP381AC20 CRZMJ 04ANGLE,HOLE,MOUNTING MOUNTING HOLE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CRZNH /D/ 18TYPE PER POLE,PROTECTION,CIRCUIT CIRCUIT PROTECTION TYPE PER POLE THE ELECTRICAL CONDITION THAT WILL CAUSE THE DEVICE FOR EACH POLE TO TRIP. 2D MODE REPLY 22AJ492AP31 CRZPJ 04WIDTH,RECESS,BODY BODY RECESS WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CRZQG 19ADDITIVE,MANDATORY MANDATORY ADDITIVE THE MANDATORY ADDITIVE(S) USED TO IMPART A DESIRED CHARACTERISTIC. FULL TEXT WRITE-IN 0 CRZRJ A12QUANTITY,TERMINAL,FEEDTHRU FEEDTHRU TERMINAL QUANTITY THE NUMBER OF TERMINALS FURNISHED WITH THE ITEM WHICH HAVE CONDUCTOR CONNECTIONS ON EACH END. 1D AND 1A MODE REPLY11AN96 CRZSJ 04DISTANCE FROM HEAD LARGEST BEARING SURFACE TO SHANK HOLE CENTER DISTANCE FROM HEAD LARGEST BEARING SURFACE TO SHANK HOLE CENTER THE DISTANCE FROM THE SHANK HOLE CENTERLINE TO THE LARGEST BEARING SURFACE OF THE HEAD. 2D AND 1B MODE REPLY21AA051AC20 CRZTH /D/ 18TYPE AND PUMP DESIGNATION,STROKE,RECIPROCATING RECIPROCATING STROKE TYPE AND PUMP DESIGNATION INDICATES THE TYPE OF RECIPROCATING MOVEMENT WITHIN THE ITEM,AND THE PUMP DESIGNATION. 2D MODE REPLY 21AC013AA96 CRZWJ 04DIAMETER AND LOCATION,HOLE HOLE DIAMETER AND LOCATION THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE,AND THE LOCATION. 3D AND 1B MODE REPLY31AA051AC203AN73 CRZXJ A08LOCATION AND QUANTITY,RESISTOR RESISTOR LOCATION AND QUANTITY INDICATES THE LOCATION AND NUMBER OF RESISTORS PROVIDED ON THE ITEM. 1D AND 1A MODE REPLY13AN73 CRZYD /D/ 07CAPABILITY,ACTION,SECOND END SWIVEL SECOND END SWIVEL ACTION CAPABILITY AN INDICATION OF WHETHER OR NOT THE END HAS THE CAPABILITY TO ROTATE. SELECT REPLY CODE 10AN90 CRZZJ 04DIAMETER,HOLE,WIRE WIRE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSBBJ 04DIAMETER,GROOVE,RADIAL RADIAL GROOVE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSBCJ /D/ 04RADIUS,CORNER,FIRST FIRST CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CSBDJ 04DISTANCE FROM CONDUCTOR HOLE TO INSULATOR END,FIRST FIRST DISTANCE FROM CONDUCTOR HOLE TO INSULATOR END NONE. 2D AND 1B MODE REPLY21AA051AC20 CSBFJ 04DEPTH,HOLE,TAPERED TAPERED HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSBGJ 04DEPTH BELOW SURFACE,REACH REACH DEPTH BELOW SURFACE NONE. 2D AND 1B MODE REPLY21AA051AC20 CSBHJ 10VOLTAGE IN VOLTS AND CURRENT TYPE VOLTAGE IN VOLTS AND CURRENT TYPE THE TOTAL ELECTRICAL VOLTAGE,EXPRESSED IN VOLTS,AND THE TYPE OF CURRENT WHETHER ALTERNATING OR DIRECT. 1D AND 1B MODE REPLY12AN87 CSBJJ /D/ 04DIAMETER,HOLE,CLINCH PLATE CLINCH PLATE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSBKH /D/ 18TYPE AND DESIGNATION,PRIME MOVER PRIME MOVER TYPE AND DESIGNATION INDICATES THE TYPE OF PRIME MOVER INCLUDED WITH THE ITEM,AND ITS DESIGNATION. 2D MODE REPLY 22AG271AP23 CSBLJ /D/ 04DIAMETER,BORE,LARGEST,BEARING BEARING LARGEST BORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSBMJ 04LENGTH,HOLE,SECOND SECOND HOLE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSBNJ 04WIDTH,CUT,CORNER CORNER CUT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSBPA 12QUANTITY,CONTAINER,TERTIARY,TOTAL TOTAL TERTIARY CONTAINER QUANTITY THE NUMBER OF TERTIARY CONTAINERS WITHIN THE UNIT PACKAGE. 1A MODE REPLY 0 CSBQJ A12QUANTITY,SET,COMMON FEEDTHRU RECEPTACLE COMMON FEEDTHRU RECEPTACLE SET QUANTITY THE NUMBER OF SETS OF COMMON TAPER PIN FEEDTHRU RECEPTACLES PROVIDED IN THE ITEM. 1D AND 1A MODE REPLY11AN97 CSBRJ 04WIDTH,SLOT,STUD STUD SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSBSJ /D/ 13THREAD SIZE,NOMINAL,BULKHEAD BULKHEAD NOMINAL THREAD SIZE THE NOMINAL SIZE USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE BULKHEAD THREAD. 1D AND 1B MODE REPLY11AA05 CSBTJ /D/T10RANGE,ADJUSTMENT,CONTACT DEACTUATION POINT CONTACT DEACTUATION POINT ADJUSTMENT RANGE THE MINIMUM AND MAXIMUM LIMITS TO WHICH THE DEACTUATION POINT OF THE CONTACTS MAY BE ADJUSTED. 1D AND 1F MODE REPLY12AG20 CSBWJ 08LOCATION FROM CCW TERMINAL PER SECTION IN OHMS,TAP TAP LOCATION FROM CCW TERMINAL PER SECTION IN OHMS INDICATES THE LOCATION OF A TAP RELATIVE TO THE COUNTERCLOCKWISE TERMINAL PER SECTION,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY12AH19 CSBXH 19CHARACTERISTIC PER SECTION,FUNCTION FUNCTION CHARACTERISTIC PER SECTION THE SPECIFIED MATHEMATICAL RELATION PER SECTION BETWEEN THE TERMINAL RESISTANCE,OR OUTPUT RATIO,AND THE ROTATION OF THE ACTUATOR. 2D MODE REPLY 22AH192AC85 CSBYJ 04LENGTH,HOLE,WIRE WIRE HOLE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSBZJ 04DEPTH,HOLE,TOP TOP HOLE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSCBJ /D/ 10STIMULUS RATING,DIFFERENTIAL,CONTACT ACTUATING CONTACT ACTUATING DIFFERENTIAL STIMULUS RATING THE DIFFERENCE IN THE STIMULUS REQUIRED TO ACTUATE AND DEACTUATE THE CONTACTS. 2D AND 1B MODE REPLY22AG201AC20 CSCCJ 10PRESSURE,BURST,SENSING ELEMENT SENSING ELEMENT BURST PRESSURE THE PRESSURE AT WHICH THE PRESSURE SENSING ELEMENT OF THE ITEM IS RENDERED INOPERATIVE BY RUPTURE OR OTHER PERMANENT PHYSICAL DAMAGE. 1D AND 1B MODE REPLY12AG20 CSCDH /D/ 18TYPE AND LOCATION,CONNECTOR,PRESSURE PRESSURE CONNECTOR TYPE AND LOCATION INDICATES THE TYPE AND LOCATION OF THE PRESSURE CONNECTOR. 2D MODE REPLY 23AJ573AN73 CSCFD 18TYPE,TERMINAL TERMINAL TYPE INDICATES THE TYPE OF TERMINAL FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. SELECT REPLY CODE 10AN89 CSCGJ 04DIAMETER,END,LARGE,PIN PIN LARGE END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGE END OF A PIN,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CSCHJ 04DIAMETER,OUTSIDE,OVERALL,BEARING BEARING OVERALL OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BEARING,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CSCJJ 04LENGTH,PORTION,MOUNTING MOUNTING PORTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSCKJ 04DIAMETER,HOLE,RECEPTACLE RECEPTACLE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSCLH /D/ 18TYPE AND LOCATION,ADJUSTMENT,CONTACT ACTUATION POINT CONTACT ACTUATION POINT ADJUSTMENT TYPE AND LOCATION INDICATES THE TYPE AND LOCATION OF THE DEVICE PROVIDED FOR MANUAL ADJUSTMENT OF THE CONTACT ACTUATION POINT. 2D MODE REPLY 23AN732AG18 CSCMJ 04WIDTH,GROOVE,SECOND RADIAL SECOND RADIAL GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSCNJ 13THREAD SIZE,NOMINAL,THIRD END THIRD END NOMINAL THREAD SIZE THE DESIGNATION WHICH IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE NOMINAL THREAD SIZE. 1D AND 1B MODE REPLY11AA05 CSCPJ /D/T13THREAD PITCH DIAMETERS,BULKHEAD BULKHEAD THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF THE BULKHEAD STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 CSCQJ 04ANGLE,POINTER POINTER ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSCRJ A18TYPE,LINK,TERMINAL CONNECTING TERMINAL CONNECTING LINK TYPE INDICATES THE TYPE OF TERMINAL CONNECTING LINK/S/ FURNISHED WITH THE ITEM. 1D AND 1A MODE REPLY12AK17 CSCSJ A12QUANTITY,TERMINAL,NONFEEDTHRU NONFEEDTHRU TERMINAL QUANTITY THE NUMBER OF NONFEEDTHRU TERMINALS FURNISHED WITH THE ITEM. 1D AND 1A MODE REPLY12AK17 CSCTJ 04WIDTH,HOLE,FIRST FIRST HOLE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSCWA 12QUANTITY,CONTAINER,PRIMARY,TOTAL TOTAL PRIMARY CONTAINER QUANTITY THE NUMBER OF PRIMARY CONTAINERS WITHIN THE ITEM OF SUPPLY. 1A MODE REPLY 0 CSCXA 12QUANTITY,CONTAINER,SECONDARY,TOTAL TOTAL SECONDARY CONTAINER QUANTITY THE NUMBER OF SECONDARY CONTAINERS WITHIN THE NEXT LEVEL OF PACKAGING. 1A MODE REPLY 0 CSCYJ T10COEFFICIENT OF RESISTANCE WIRE PER SECTION IN PPM PER DEG CELSIUS,TEMP TEMP COEFFICIENT OF RESISTANCE WIRE PER SECTION IN PPM PER DEG CELSIUS A CONSTANT THAT REPRESENTS THE PROPORTIONATE CHANGE IN RESISTANCE OF THE WIRE PER SECTION OF WHICH THE RESISTANCE ELEMENT OF A RESISTOR IS WOUND,EXPRESSED IN PARTS PER MILLION PER DEGREE CELSIUS. 1D AND 1F MODE REPLY12AH19 CSCZA /D/ 13THREAD QUANTITY PER INCH,END,THIRD THIRD END THREAD QUANTITY PER INCH THE NUMBER OF THREADS PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CSDBJ 04WIDTH,SLOT,SECOND SECOND SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSDCJ 10SETTING,PRESSURE,OPENING OPENING PRESSURE SETTING THE PREDETERMINED PRESSURE AT WHICH THE ITEM IS CALIBRATED TO OPEN. 1D AND 1B MODE REPLY11AN71 CSDDJ 10SPACING,HOLE,SIXTH SIXTH HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 CSDFD 13THREAD SERIES DESIGNATOR,END,THIRD THIRD END THREAD SERIES DESIGNATOR A DESIGNATOR DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CSDGJ /D/ 04LENGTH,OVERALL,GEAR CLUSTER GEAR CLUSTER OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSDHJ 10TEMP IN DEG CELSIUS PER SECTION AT FULL RATED POWER,AMBIENT AMBIENT TEMP IN DEG CELSIUS PER SECTION AT FULL RATED POWER THE AMBIENT TEMPERATURE,EXPRESSED IN DEGREES CELSIUS,OF THE MEDIUM SURROUNDING EACH SECTION AT WHICH IT CAN BE OPERATED CONTINUOUSLY AT FULL RATED POWER. 1D AND 1B MODE REPLY12AH19 CSDJJ 04DIAMETER,HOLE,SECOND WIRE SECOND WIRE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSDKJ 18TYPE AND RATING IN AMPS,CURRENT,SWITCH SWITCH CURRENT TYPE AND RATING IN AMPS INDICATES THE TYPE OF ELECTRICAL CURRENT AND THE CAPACITY FOR NORMAL OPERATION OF THE SWITCH,EXPRESSED IN AMPERES. 1D AND 1B MODE REPLY12AN87 CSDLJ A10CURVE PER SECTION,TAPER,STANDARD STANDARD TAPER CURVE PER SECTION THE RATE OF CHANGE AND DISTRIBUTION OF RESISTANCE PER SECTION,IN RELATION TO THE ROTATION OF THE CONTROL SHAFT,WHICH ESTABLISHES A STANDARD TAPER CURVE DESIGNATED BY AN ALPHABETIC CHARACTER AND ACCEPTED FOR COMMON USAGE. 1D AND 1A MODE REPLY12AH19 CSDMJ 10SPACING,HOLE,NINTH NINTH HOLE SPACING NONE. 2D AND 1B MODE REPLY21AA051AC20 CSDNJ 04DISTANCE,OUTER EDGE TO GROOVE EDGE OUTER EDGE TO GROOVE EDGE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CSDPD 18TYPE,PAD PAD TYPE INDICATES THE TYPE OF CUSHIONING DEVICE PROVIDED. SELECT REPLY CODE 10AP40 CSDQJ 04DIAMETER FROM HEAD,NINTH NINTH DIAMETER FROM HEAD NONE. 2D AND 1B MODE REPLY21AA051AC20 CSDRJ 12LENGTH AND QUANTITY PER SET,NOMINAL,TIE TIE NOMINAL LENGTH AND QUANTITY PER SET A MEASUREMENT OF THE LONGEST NOMINAL DIMENSION OF THE TIE,IN DISTINCTION FROM WIDTH,AND THE NUMBER OF TIES PER SET. 2D AND 1B MODE REPLY21AA053AF81 CSDSJ /D/ 04DIAMETER,OUTSIDE,OVERALL,ROD END ROD END OVERALL OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSDTJ 04DIAMETER,INSIDE,EYELET EYELET INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSDWD 19CONSTRUCTION,KNIT KNIT CONSTRUCTION THE PROCESS OF MANUFACTURING A FABRIC BY A SERIES OF INTERLOCKING LOOPS OF ONE OR MORE YARNS. SELECT REPLY CODE 10AP00 CSDXJ A19CONFIGURATION AND POLE QUANTITY,CIRCUIT,INTERNAL INTERNAL CIRCUIT CONFIGURATION AND POLE QUANTITY THE PATTERN OF CONDUCTORS AND CONNECTIONS WITHIN THE ITEM WHICH,WHEN FUSED,PROVIDES ELECTRICAL CONTINUITY TO MAINLINE CIRCUITS OR FROM MAINLINE TO BRANCH CIRCUITS,AS APPLICABLE,AND THE NUMBER OF POLES. 1D AND 1A MODE REPLY12AP09 CSDYJ /D/ 04DISTANCE BETWEEN FIRST AND SECOND TURRET DISTANCE BETWEEN FIRST AND SECOND TURRET NONE. 2D AND 1B MODE REPLY21AA051AC20 CSDZJ /D/ 04THICKNESS,SPACER SPACER THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CSFBJ 04DIAMETER AND LOCATION,MAJOR,COUNTERSINK COUNTERSINK MAJOR DIAMETER AND LOCATION THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST DIMENSION OF A COUNTERSINK,AND TERMINATES AT THE INNER CIRCUMFERENCE,AND THE LOCATION. 3D AND 1B MODE REPLY31AA051AC203AN73 CSFCJ 04HEIGHT,OUTSIDE,WAVEGUIDE WAVEGUIDE OUTSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CSFDD 19CHARACTERISTICS,DEFECT FREE DEFECT FREE CHARACTERISTICS THE DEFECT FREE CHARACTERISTICS OF THE ITEM. SELECT REPLY CODE 10AP04 CSFFJ /D/ 04DIAMETER,OUTSIDE,NEEDLE BEARING NEEDLE BEARING OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSFGJ 10REACTANCE IN OHMS,ZSS,PLUS J PLUS J ZSS REACTANCE IN OHMS THE REACTANCE /X/ PART OF THE STATOR IMPEDANCE WITH THE ROTOR SHORTED /ZSS/,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 CSFHJ 10TEMP RATING PER FUNCTION TEMP RATING PER FUNCTION THE DEGREE OF HEAT OR COLD AS APPLIED TO THE FUNCTION OF THE ITEM. 2D AND 1B MODE REPLY21AB361AA88 CSFJD 18TYPE,ACCOMMODATION,CONDUCTOR CONDUCTOR ACCOMMODATION TYPE INDICATES THE TYPE OF CONNECTOR OR CONDUCTOR ACCOMMODATION INCLUDED ON THE ITEM. SELECT REPLY CODE 10AP10 CSFKJ /D/ 04DISTANCE BETWEEN HOLES AND TYPE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN HOLES AND TYPE THE CENTER TO CENTER DISTANCE BETWEEN THE HOLES AND THE TYPE OF HOLE. 3D AND 1B MODE REPLY31AA051AC202AH37 CSFLJ 04ANGLE,HEAD,ASKEWED ASKEWED HEAD ANGLE THE ANGLE OF THE HEAD BEARING SURFACE IN RELATION TO THE LONGITUDINAL AXIS OF THE ITEM. 2D AND 1B MODE REPLY21AP381AC20 CSFMJ 04DEPTH,UNDERCUT UNDERCUT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSFNJ A19FINISH AND LOCATION,SURFACE SURFACE FINISH AND LOCATION DESIGNATES THE SPECIFIC ROUGHNESS RATING REPRESENTING THE ARITHMETIC AVERAGE DEVIATION OF THE SURFACE FROM THE MEANLINE IN PROFILE,AND ITS LOCATION ON THE ITEM. 2D AND 1A MODE REPLY21AE863AN73 CSFPJ /D/ 10AMPERES-CURRENT TYPE AND DESIGNATION,PRIME MOVER PRIME MOVER AMPERES-CURRENT TYPE AND DESIGNATION THE ELECTRICAL CURRENT,EXPRESSED IN AMPERES,AND THE CURRENT TYPE OF THE PRIME MOVER AND ITS DESIGNATION. 2D AND 1B MODE REPLY22AN871AP23 CSFQH /D/ 14SHAPE AND LOCATION,CORNER CORNER SHAPE AND LOCATION THE PREFORMED SHAPE OF THE CORNER(S) AND THE LOCATION ON THE ITEM. 2D MODE REPLY 23AP003AN73 CSFRJ /D/ 10TRIP RATING OF CONTINUOUS CURRENT PER POLE IN PERCENT,ULTIMATE ULTIMATE TRIP RATING OF CONTINUOUS CURRENT PER POLE IN PERCENT THE CONTINUOUS CURRENT AT WHICH EACH POLE OF THE DEVICE IS RATED TO TRIP WITHIN A SPECIFIED TIME,EXPRESSED IN PERCENT. 1D AND 1B MODE REPLY12AP31 CSFSD /D/ 19LIMITS,VARIATION,USP WEIGHT USP WEIGHT VARIATION LIMITS AN INDICATION THAT THE VARIATION IN THE WEIGHTS OF INDIVIDUAL DOSAGE UNITS,EXPRESSED IN TERMS OF THE ALLOWABLE DEVIATION FROM THE AVERAGE WEIGHT OF THE SAMPLE MEET THE REQUIREMENTS FOR THE USP WEIGHT VARIATION TEST. SELECT REPLY CODE 10AP12 CSFTD 13THREAD LOCATION,BASE BASE THREAD LOCATION INDICATES THE LOCATION OF THE THREAD ON THE BASE. SELECT REPLY CODE 10AN73 CSFWJ 04ANGLE BETWEEN EXTERNAL KEYS ANGLE BETWEEN EXTERNAL KEYS NONE. 2D AND 1B MODE REPLY21AP381AC20 CSFXD /D/ 11METHOD,LOCKING,SWITCH ACTUATOR SWITCH ACTUATOR LOCKING METHOD THE MEANS USED FOR LOCKING THE SWITCH ACTUATOR. SELECT REPLY CODE 10AD90 CSFYB /D/ 04TAPER PER FOOT IN INCHES,CONE CONE TAPER PER FOOT IN INCHES NONE. 1B MODE REPLY 0 CSFZJ 04DIAMETER OF BRUSH PART,SINGLE BRUSH SINGLE BRUSH DIAMETER OF BRUSH PART NONE. 2D AND 1B MODE REPLY21AA051AC20 CSGBJ 04DIAMETER,MAJOR,STUD SHANK STUD SHANK MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSGCD 11METHOD,FEED,FUEL FUEL FEED METHOD THE MEANS BY WHICH THE FUEL IS FED TO THE ITEM. SELECT REPLY CODE 10AL50 CSGDJ /D/ 04DIAMETER,MINOR,BUSHING BUSHING MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSGFJ A19DOCUMENT AND CLASSIFICATION,MATERIAL,CONTACT CONTACT MATERIAL DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS CLASS,CONDITION,TEMPER,AND THE LIKE,THAT IDENTIFIES THE CONTACT MATERIAL. 2D AND 1A MODE REPLY21AP331AP18 CSGGJ 10CURRENT RATING AT MAXIMUM AC VOLTAGE RATING,CONTACT LOAD CONTACT LOAD CURRENT RATING AT MAXIMUM AC VOLTAGE RATING THE AMOUNT OF CURRENT THE CONTACTS ARE RATED TO MAKE OR BREAK AT MAXIMUM RATED ALTERNATING CURRENT VOLTAGE WITH A SPECIFIED LOAD. MRC DISCONTINUED FOR GENERAL USE, MRC MAINTAINED FOR DTRA USE ONLY. 2D AND 1B MODE REPLY21AC302AK53 CSGHJ 10SPACING,ANGULAR,MOUNTING HOLE MOUNTING HOLE ANGULAR SPACING NONE. 2D AND 1B MODE REPLY21AP381AC20 CSGJA /D/ 13THREAD CLASS,INTERNAL,HEAD HEAD INTERNAL THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE OF THE INTERNAL THREAD. 1A MODE REPLY 0 CSGKL 16STYLE,BRUSH,SECOND SECOND BRUSH STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SECOND BRUSH. 1L MODE REPLY 0 CSGLJ 04RADIUS,TIP,SECOND END SECOND END TIP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CSGMJ 04DIAMETER,OUTSIDE,WAVEGUIDE WAVEGUIDE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSGNJ /D/ 04WIDTH,RING,INNER,NEEDLE BEARING NEEDLE BEARING INNER RING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSGPJ 04DISTANCE FROM BODY TOP TO UNDERCUT DISTANCE FROM BODY TOP TO UNDERCUT NONE. 2D AND 1B MODE REPLY21AA051AC20 CSGQJ /D/ 04LENGTH AND TYPE,GAIN,NOMINAL NOMINAL GAIN LENGTH AND TYPE A MEASUREMENT OF THE LONGEST NOMINAL DIMENSION OF THE GAIN AND THE TYPE OF GAIN ON THE ITEM. 2D AND 1B MODE REPLY21AA053AK54 CSGRJ /D/ 04LENGTH,INSULATOR INSULATOR LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE INSULATOR,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CSGSD 19ADMINISTRATION ADMINISTRATION AN INDICATION OF THE AREA,ORIFICE,OR TISSUE OF THE BODY TO WHICH THE MEDICATION IS ADMINISTERED OR APPLIED,BASED ON THE DRUG FORMULATION. SELECT REPLY CODE 10AG60 CSGTJ A18TYPE AND QUANTITY REQUIRED,BATTERY BATTERY TYPE AND QUANTITY REQUIRED INDICATES THE TYPE AND NUMBER OF BATTERIES REQUIRED FOR OPERATION. 1D AND 1A MODE REPLY12AD57 CSGWA 19NUMBER,CODE,NATO NATO CODE NUMBER THE DESIGNATOR WHICH IS ASSIGNED TO THE PRODUCT BY THE NATO MILITARY AGENCY FOR STANDARDIZATION(MAS). 1A MODE REPLY 0 CSGXD 01COLOR,SURFACE CONDITION SURFACE CONDITION COLOR THE HUE OR TINT OF THE SURFACE CONDITION. SELECT REPLY CODE 10AD06 CSGYJ 04LENGTH,LEG,VERTICAL VERTICAL LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSGZJ 04ANGLE BETWEEN PINS ANGLE BETWEEN PINS NONE. 2D AND 1B MODE REPLY21AP381AC20 CSHBG 04THICKNESS,RANDOM RANDOM THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. FULL TEXT WRITE-IN 0 CSHCJ /D/ 04WIDTH,BODY,ROD END ROD END BODY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSHDJ /D/ 13THREAD DIAMETER,NOMINAL,COUNTERBORE COUNTERBORE NOMINAL THREAD DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED COUNTERBORE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CSHFJ 04DIAMETER,NOMINAL,HOLE,PANEL MOUNTING RAIL PANEL MOUNTING RAIL HOLE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PANEL MOUNTING RAIL HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CSHGJ 04HEIGHT,HEEL HEEL HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE HEEL. 1D AND 1B MODE REPLY11AA05 CSHHJ /D/ 10FREQUENCY AND FUNCTION FREQUENCY AND FUNCTION THE FUNCTION AND THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE ITEM IS DESIGNED. 3D AND 1B MODE REPLY31AE061AC202AK27 CSHJD 19DEVICE,PROTECTION,LAMP LAMP PROTECTION DEVICE THE MEANS PROVIDED TO PROTECT THE LAMP FROM DAMAGE. SELECT REPLY CODE 10AD60 CSHKJ 04ANGLE BETWEEN SECOND AND THIRD KEY ANGLE BETWEEN SECOND AND THIRD KEY NONE. 2D AND 1B MODE REPLY21AP381AC20 CSHLJ /D/ 04WIDTH,RING RING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSHMJ /D/ 04RADIUS,RING RING RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CSHNJ /D/ 04DISTANCE BETWEEN SECOND AND THIRD TURRET DISTANCE BETWEEN SECOND AND THIRD TURRET NONE. 2D AND 1B MODE REPLY21AA051AC20 CSHPJ 04THICKNESS-LOCATION AND MEASURING METHOD THICKNESS-LOCATION AND MEASURING METHOD A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH,ITS LOCATION ON THE ITEM,AND THE MEASURING METHOD USED. 4D AND 1B MODE REPLY41AA051AC203AN732AN68 CSHQJ /D/ 10SPEED AT RATED CAPACITY AND PUMP DESIGNATION,OPERATING OPERATING SPEED AT RATED CAPACITY AND PUMP DESIGNATION THE SPEED AT WHICH AN ITEM OPERATES TO PRODUCE ITS RATED CAPACITY,AND THE PUMP DESIGNATION. 2D AND 1B MODE REPLY21AA223AA96 CSHRJ 04DISTANCE,CURVATURE CENTER TO BRUSH LONG SIDE CURVATURE CENTER TO BRUSH LONG SIDE DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CSHSJ /D/ 04DIAMETER,ROLLER ROLLER DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSHTJ 04DIAMETER,SHANK,FASTENER STUD FASTENER STUD SHANK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSHWD 19ACTION,SWITCHING,CONTACT CONTACT SWITCHING ACTION AN INDICATION OF THE SWITCHING ACTION BY THE CONTACTS OF THE ITEM. SELECT REPLY CODE 10AD78 CSHXB /D/ 04TAPER PER FOOT IN INCHES,ROLLER ROLLER TAPER PER FOOT IN INCHES NONE. 1B MODE REPLY 0 CSHYD /D/ 18TYPE,DEVICE,OVERLOAD PROTECTION OVERLOAD PROTECTION DEVICE TYPE INDICATES THE TYPE OF DEVICE PROVIDED TO PREVENT OVERLOAD TO THE WINDINGS OF AN ITEM. SELECT REPLY CODE 10AC08 CSHZJ A19DOCUMENT AND CLASSIFICATION,MATERIAL,BODY BODY MATERIAL DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS CLASS,CONDITION,TEMPER,AND THE LIKE,THAT IDENTIFIES THE BODY MATERIAL. 2D AND 1A MODE REPLY21AP331AP18 CSJBJ A08LOCATION AND QUANTITY,PROJECTION,WELDING WELDING PROJECTION LOCATION AND QUANTITY INDICATES THE LOCATION AND NUMBER OF WELDING PROJECTIONS ON THE ITEM. 1D AND 1A MODE REPLY13AN73 CSJCJ 13THREAD SIZE,NOMINAL,MOUNTING FACILITY MOUNTING FACILITY NOMINAL THREAD SIZE A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE MOUNTING FACILITY THREAD. 1D AND 1B MODE REPLY11AA05 CSJDJ 13THREAD SIZE,NOMINAL,OUTLET OUTLET NOMINAL THREAD SIZE A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE OUTLET THREAD. 1D AND 1B MODE REPLY11AA05 CSJFJ 04ANGLE,COUNTERSINK,FIRST END FIRST END COUNTERSINK ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSJGA /D/ 13THREAD QUANTITY PER INCH,COUNTERBORE COUNTERBORE THREAD QUANTITY PER INCH THE NUMBER OF COUNTERBORE THREADS PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CSJHJ 04ANGLE,DEFLECTION,TERMINAL END TERMINAL END DEFLECTION ANGLE THE ANGLE OF DEFLECTION BETWEEN TWO STRAIGHT LINES AT THE TERMINAL END. 2D AND 1B MODE REPLY21AP381AC20 CSJJH /D/ 11METHOD PER POLE,RELEASE,TRIP TRIP RELEASE METHOD PER POLE THE MEANS BY WHICH THE TRIP MECHANISM FOR EACH POLE IS RELEASED. 2D MODE REPLY 23AK662AP31 CSJKD 18TYPE,INPUT,AUXILIARY AUXILIARY INPUT TYPE INDICATES THE TYPE OF AUXILIARY INPUT. SELECT REPLY CODE 10AC58 CSJLD 18TYPE,MATERIAL,CORE CORE MATERIAL TYPE INDICATES THE TYPE OF MATERIAL COMPOSING THE CORE. SELECT REPLY CODE 10AN48 CSJMJ /D/ 04WIDTH,FLANGE,CUP CUP FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSJNJ 10FORCE,ACTUATING,SWITCH SWITCH ACTUATING FORCE THE AMOUNT OF FORCE REQUIRED TO ACTUATE THE SWITCH. 2D AND 1B MODE REPLY21AA561AC20 CSJPJ /D/A12QUANTITY AND PUMP DESIGNATION,CYLINDER CYLINDER QUANTITY AND PUMP DESIGNATION THE NUMBER OF CYLINDERS INCLUDED IN THE ITEM,AND THE PUMP DESIGNATION. 1D AND 1A MODE REPLY13AA96 CSJQD /D/ 09MATERIAL,FACE,TARGET TARGET FACE MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE TARGET FACE IS FABRICATED. SELECT REPLY CODE 10AD09 CSJRD 19RELATIONSHIP TO INTAKE CONNECTION,CONNECTION,FIRST DISCHARGE FIRST DISCHARGE CONNECTION RELATIONSHIP TO INTAKE CONNECTION INDICATES THE FIRST DISCHARGE CONNECTION RELATIONSHIP TO AN INTAKE CONNECTION. SELECT REPLY CODE 10AB78 CSJSJ 04DIAMETER OF BRUSH PART,FIRST BRUSH FIRST BRUSH DIAMETER OF BRUSH PART NONE. 2D AND 1B MODE REPLY21AA051AC20 CSJTJ /D/ 10RATIO,SPEED SPEED RATIO THE VALUES OF SPEEDS OF THE TRANSMITTER AND THE INDICATOR IN RELATION TO EACH OTHER. 1D AND 1B MODE REPLY13AK54 CSJWA 03DESIGNATOR,BULB BULB DESIGNATOR A DESIGNATION WHICH INDICATES THE SHAPE AND SIZE OF THE BULB. 1A MODE REPLY 0 CSJXD 08LOCATION,ADHESIVE ADHESIVE LOCATION INDICATES THE LOCATION OF THE ADHESIVE ON THE ITEM. SELECT REPLY CODE 10AN73 CSJYJ 10RATIO,TRANSFORMATION TRANSFORMATION RATIO THE RATIO OF THE OUTPUT VOLTAGE TO THE INPUT VOLTAGE AT MAXIMUM COUPLING. 2D AND 1B MODE REPLY22AG011AC20 CSJZJ 04LENGTH,SHANK,STUD END STUD END SHANK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSKBJ /D/ 13THREAD SIZE,NOMINAL,HEAD INTERNAL HEAD INTERNAL NOMINAL THREAD SIZE A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE HEAD INTERNAL THREAD. 1D AND 1B MODE REPLY11AA05 CSKCJ 04ANGLE,TAPER TAPER ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSKDJ 04HEIGHT OF FORKS,LIFT LIFT HEIGHT OF FORKS NONE. 2D AND 1B MODE REPLY21AA051AC20 CSKFJ /D/ 04HEIGHT,OVERALL,CLINCH PLATE CLINCH PLATE OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CSKGJ 04ANGLE,BEND BEND ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSKHD 19CHARACTERISTIC,TRANSMISSION,LENS LIGHT LENS LIGHT TRANSMISSION CHARACTERISTIC AN INDICATION OF THE LIGHT TRANSMISSION CHARACTERISTIC OF THE LENS. SELECT REPLY CODE 10AF93 CSKJJ 04ANGLE,CONE CONE ANGLE NONE. 1D AND 1B MODE REPLY11AP38 CSKKJ /D/ 04ANGLE BETWEEN MOUNTING FACILITY AND CONDUCTOR ACCOMMODATION CENTERLINES ANGLE BETWEEN MOUNTING FACILITY AND CONDUCTOR ACCOMMODATION CENTERLINES NONE. 2D AND 1B MODE REPLY21AP381AC20 CSKLJ 04DISTANCE FROM HOOK CENTER TO NEAREST OUTSIDE EDGE ALONG WIDTH DISTANCE FROM HOOK CENTER TO NEAREST OUTSIDE EDGE ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSKMJ 04RADIUS,OUTER,FIRST END FIRST END OUTER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CSKNJ 04ANGLE,KEY,PREBENT,EXTERNAL EXTERNAL PREBENT KEY ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSKPJ A19ARRANGEMENT,CONTACT,AUXILIARY,NONPILE-UP NONPILE-UP AUXILIARY CONTACT ARRANGEMENT THE DESIGNATION THAT IDENTIFIES THE SCHEMATIC DIAGRAM OF THE ELECTRICAL CONFIGURATION OF THE AUXILIARY NONPILE-UP CONTACTS INCLUDING THE NUMBER OF POLES OR FORMS. 1D AND 1A MODE REPLY12AG28 CSKQJ /D/ 13THREAD LENGTH,COUNTERBORE COUNTERBORE THREAD LENGTH A MEASUREMENT OF THE EXTENT OF THE COUNTERBORE THREAD MEASURED ON A LINE PARALLEL TO THE LONGITUDINAL AXIS. 2D AND 1B MODE REPLY21AA051AC20 CSKRJ 04ANGLE,POINT POINT ANGLE THE ANGLE TO WHICH THE POINT IS FORMED,PER SPECIFIC MEASUREMENT SCALE. 2D AND 1B MODE REPLY21AP381AC20 CSKSD 18TYPE,CONNECTION,FIRST DISCHARGE FIRST DISCHARGE CONNECTION TYPE INDICATES THE TYPE OF CONNECTION ON THE FIRST DISCHARGE. SELECT REPLY CODE 10AB76 CSKTD 02DESIGN,POINTER POINTER DESIGN INDICATES WHETHER OR NOT THE POINTER IS DESIGNED AS AN INTEGRAL PART OF THE ITEM. SELECT REPLY CODE 10AH97 CSKWJ 10VOLTAGE IN VOLTS AND CURRENT TYPE,MAXIMUM,CONTACT CONTACT MAXIMUM VOLTAGE IN VOLTS AND CURRENT TYPE THE MAXIMUM POTENTIAL,EXPRESSED IN VOLTS,AND THE CURRENT TYPE THAT MAY BE APPLIED CONTINUOUSLY TO THE CONTACTS WITHOUT DAMAGE. 1D AND 1B MODE REPLY12AN87 CSKXJ 04DEPTH,OVERALL,BODY BODY OVERALL DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSKYJ 04DISTANCE FROM BOTTOM OF BODY TO CENTER OF INLET DISTANCE FROM BOTTOM OF BODY TO CENTER OF INLET NONE. 2D AND 1B MODE REPLY21AA051AC20 CSKZJ 04DIAMETER,OUTSIDE,ELEMENT ELEMENT OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSLBH /D/ 13THREAD SERIES DESIGNATOR-LOCATION AND PUMP DESIGNATION THREAD SERIES DESIGNATOR-LOCATION AND PUMP DESIGNATION A DESIGNATION INDICATING THE DIAMETER-PITCH AND NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO THE DIAMETER OF A SPECIFIC LOCATION ON THE ITEM,AND THE PUMP DESIGNATION. 3D MODE REPLY 32AH063AN733AA96 CSLCJ 10POSITIONING INCREMENT,ACTUATOR,SWITCH SWITCH ACTUATOR POSITIONING INCREMENT THE INCREMENTS OF ANGULAR ROTATION THAT THE SWITCH ACTUATOR MOVES BETWEEN ADJACENT INDEX POSITIONS. 1D AND 1B MODE REPLY11AP38 CSLDJ 04DISTANCE FROM INSIDE OPENING TO BASE EDGE DISTANCE FROM INSIDE OPENING TO BASE EDGE NONE. 2D AND 1B MODE REPLY21AA051AC20 CSLFD /D/ 02DESIGN,INSTRUMENT,HARDNESS TESTER HARDNESS TESTER INSTRUMENT DESIGN THE DESIGN OF THE INSTRUMENT USED TO DETERMINE THE HARDNESS OF THE ITEM. SELECT REPLY CODE 10AJ50 CSLGJ /D/ 04DIAMETER,HOLE,DOWEL DOWEL HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSLHD 19CHARACTERISTIC,SCORING SCORING CHARACTERISTIC AN INDICATION OF WHETHER DISSECTING GROOVES ARE ON THE FACE/S/ OF THE ITEM TO FACILITATE BREAKING. SELECT REPLY CODE 10AG58 CSLJB 10PERCENTAGE,VOLUME,DISTILLATION RESIDUE,MAXIMUM MAXIMUM DISTILLATION RESIDUE VOLUME PERCENTAGE AN INDICATION OF THE MAXIMUM AMOUNT OF MATTER REMAINING AFTER DISTILLATION,EXPRESSED IN PERCENT. 1B MODE REPLY 0 CSLKD /D/ 11METHOD,PREPARATION,DOSAGE FORM DOSAGE FORM PREPARATION METHOD THE RECOGNIZED METHOD OR TECHNIQUE UTILIZED IN PREPARATION OF THE DOSAGE FORM. SELECT REPLY CODE 10AG58 CSLLF /D/T10RANGE IN DEG CELSIUS,TEMP,MELTING MELTING TEMP RANGE IN DEG CELSIUS THE MINIMUM AND MAXIMUM POINTS OF TEMPERATURE WITHIN WHICH THE SOLID IS OBSERVED TO COALESCE AND IS COMPLETELY MELTED. 1F MODE REPLY 0 CSLMJ 04ANGLE,COUNTERSINK,MINOR,HEAD HEAD MINOR COUNTERSINK ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSLND 19RELATIONSHIP TO PRECEDING CONNECTION,CONNECTION,SECOND DISCHARGE SECOND DISCHARGE CONNECTION RELATIONSHIP TO PRECEDING CONNECTION INDICATES THE SECOND DISCHARGE CONNECTION RELATIONSHIP TO THE PRECEDING CONNECTIONS. SELECT REPLY CODE 10AB78 CSLPJ /D/ 04LENGTH,SOCKET,PUSH BUTTON PUSH BUTTON SOCKET LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSLQJ 04DISTANCE BETWEEN CONNECTIONS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN CONNECTIONS NONE. 2D AND 1B MODE REPLY21AA051AC20 CSLRH 02DESIGN AND LOCATION,GUIDE GUIDE DESIGN AND LOCATION THE DESIGN OF THE POLARIZING GUIDE AND ITS LOCATION ON THE ITEM. 2D MODE REPLY 22AP523AN73 CSLSB /D/ 13THREAD PITCH IN MILLIMETERS,CONNECTION CONNECTION THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE CONNECTION THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CSLTB 04ANGLE IN DEG,TAPER,SHAFT SHAFT TAPER ANGLE IN DEG NONE. 1B MODE REPLY 0 CSLWJ /D/A16STYLE,ARRANGEMENT,CONTACT POSITION CONTACT POSITION ARRANGEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE CONTACT POSITION/S/. 1D AND 1A MODE REPLY11AP55 CSLXJ 04LENGTH,OVERALL,FITTING FITTING OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSLYJ 04DIAMETER,OUTSIDE,NOMINAL,FIRST INTAKE FIRST INTAKE NOMINAL OUTSIDE DIAMETER A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE OUTSIDE DIAMETER. 1D AND 1B MODE REPLY11AA05 CSLZG 19DOSE,USUAL USUAL DOSE THE DOSAGE OF A DRUG, FOLLOWING ITS APPLICATION, AT SUCH TIME INTERVALS AS MAY BE DESIGNATED. FULL TEXT WRITE-IN 0 CSMBJ 10TEMP RATING,MAXIMUM,VAPOR PRESSURE VAPOR PRESSURE MAXIMUM TEMP RATING THE MAXIMUM TEMPERATURE OF THE VAPOR PRESSURE FOR WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY11AB36 CSMCD 19CHARACTERISTIC,TRANSMISSION,BULB LIGHT BULB LIGHT TRANSMISSION CHARACTERISTIC AN INDICATION OF THE LIGHT TRANSMISSION CHARACTERISTIC OF THE BULB. SELECT REPLY CODE 10AF93 CSMDJ 04ANGLE BETWEEN CONNECTIONS ANGLE BETWEEN CONNECTIONS NONE. 2D AND 1B MODE REPLY21AP381AC20 CSMFJ /D/ 04DISTANCE BETWEEN DOWEL HOLE AND MOUNTING FACILITY,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN DOWEL HOLE AND MOUNTING FACILITY NONE. 2D AND 1B MODE REPLY21AA051AC20 CSMGB 10ARC IN DEG,VISIBILITY,NOMINAL NOMINAL VISIBILITY ARC IN DEG THE NOMINAL DEGREES OF ARC THE EMITTED LIGHT IS VISIBLE. 1B MODE REPLY 0 CSMHJ /D/ 13THREAD DIAMETER,NOMINAL,CONCENTRIC HOLE CONCENTRIC HOLE NOMINAL THREAD DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED CONCENTRIC HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CSMJH 04SIZE ACCOMMODATED AND LOCATION,PIN,TAPERED TAPERED PIN SIZE ACCOMMODATED AND LOCATION DESIGNATES THE SIZE OF THE TAPERED PIN THAT THE ITEM IS DESIGNED TO ACCOMMODATE AND THE LOCATION. 2D MODE REPLY 22AP163AN73 CSMKJ 04ANGLE BETWEEN INTERNAL KEY AND FIRST OFFSET KEY ANGLE BETWEEN INTERNAL KEY AND FIRST OFFSET KEY NONE. 2D AND 1B MODE REPLY21AP381AC20 CSMLJ 04DIAMETER,RECESS,BOTTOM BOTTOM RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSMMJ /D/ 04DISTANCE BETWEEN STUD MOUNTING HOLE CENTERS DISTANCE BETWEEN STUD MOUNTING HOLE CENTERS NONE. 2D AND 1B MODE REPLY21AA051AC20 CSMNJ /D/ 04DIAMETER OF BRUSH PART,SECOND BRUSH SECOND BRUSH DIAMETER OF BRUSH PART NONE. 2D AND 1B MODE REPLY21AA051AC20 CSMPJ 04DIAMETER,OUTSIDE,NOMINAL,FIRST DISCHARGE FIRST DISCHARGE NOMINAL OUTSIDE DIAMETER A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE OUTSIDE DIAMETER. 1D AND 1B MODE REPLY11AA05 CSMQJ 04DIAMETER,OUTSIDE,SCALE PORTION SCALE PORTION OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSMRJ /D/ 04DIAMETER,MAJOR,BUSHING BUSHING MAJOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSMSJ 10VALUE AT 15.56 DEG CELSIUS,GRAVITY,SPECIFIC SPECIFIC GRAVITY VALUE AT 15.56 DEG CELSIUS THE NUMERIC VALUE INDICATING THE RATIO OF THE MASS OF A BODY TO THE MASS OF AN EQUAL VOLUME OF WATER AT 15.56 DEGREES CELSIUS. 1D AND 1B MODE REPLY11AC20 CSMTD /D/ 09MATERIAL,SEAL SEAL MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE SEAL IS FABRICATED. SELECT REPLY CODE 10MA01 CSMWJ T10RANGE,TORQUE,ROTATIONAL,DETENT DETENT ROTATIONAL TORQUE RANGE THE MINIMUM AND MAXIMUM AMOUNT OF TURNING FORCE REQUIRED TO ROTATE AN ACTUATOR THROUGH THE DETENT POSITIONS. 1D AND 1F MODE REPLY11AA56 CSMXJ 10CAPACITY,WEIGHT,MAXIMUM MAXIMUM WEIGHT CAPACITY THE MAXIMUM WEIGHT THE ITEM IS DESIGNED TO SUPPORT. 1D AND 1B MODE REPLY12AN75 CSMYH /D/ 18TYPE AND PUMP DESIGNATION,DESIGN DESIGN TYPE AND PUMP DESIGNATION INDICATES THE DESIGN TYPE OF THE ITEM AND THE PUMP DESIGNATION. 2D MODE REPLY 21AA803AA96 CSMZJ 04ANGLE,INSIDE,LEFT TOP LEFT TOP INSIDE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSNBJ 10RATING IN MINUTES,SECURITY SECURITY RATING IN MINUTES A MEASUREMENT OF TIME OF THE ABILITY OF THE ITEM TO RESIST ENTRY BY UNAUTHORIZED PERSONNEL,EXPRESSED IN MINUTES. 1D AND 1B MODE REPLY12AA65 CSNCH /D/ 18TYPE AND DESIGNATION,INCLOSURE,PRIME MOVER PRIME MOVER INCLOSURE TYPE AND DESIGNATION INDICATES THE TYPE OF INCLOSURE PROVIDED TO COAT,COVER,PROTECT,OR ENCASE THE PRIME MOVER AND ITS DESIGNATION. 2D MODE REPLY 22AG851AP23 CSNDJ 18TYPE AND SIZE,DISK,FILTERING FILTERING DISK TYPE AND SIZE INDICATES THE TYPE AND SIZE OF THE FILTERING DISK PROVIDED. 2D AND 1B MODE REPLY22AG673AK95 CSNFD 18TYPE FOR WHICH DESIGNED,PROCESS PROCESS TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF PROCESS FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AL66 CSNGA 12QUANTITY,DIAMETER,EXTERNALLY RELIEVED BODY EXTERNALLY RELIEVED BODY DIAMETER QUANTITY THE NUMBER OF EXTERNALLY RELIEVED DIAMETERS ON THE BODY,ADJACENT TO THE HEAD. 1A MODE REPLY 0 CSNHJ /D/ 04WIDTH AND POSITION,OVERALL,LENS LENS OVERALL WIDTH AND POSITION NONE. 3D AND 1B MODE REPLY31AA051AC202AK17 CSNJG 19MARKING,REFERENCE REFERENCE MARKING A VISIBLE TRACING OR IMPRESSION,AND THE LIKE,OF ALPHA AND/OR NUMERIC CHARACTERS,SYMBOLS,AND THE LIKE. FULL TEXT WRITE-IN 0 CSNKJ /D/A10STRENGTH,TENSILE,TOP SURFACE TOP SURFACE TENSILE STRENGTH THE MAXIMUM LOAD IN TENSION APPLIED IN A LONGITUDINAL DIRECTION,PER UNIT OF CROSS-SECTIONAL AREA,THAT THE TOP SURFACE CAN WITHSTAND WITHOUT RUPTURE. 2D AND 1A MODE REPLY21AN711AC20 CSNLJ /D/ 04WIDTH ACCOMMODATED,TAB TAB WIDTH ACCOMMODATED NONE. 2D AND 1B MODE REPLY21AA051AC20 CSNMD 18TYPE ACCOMMODATED,TERMINAL,FUSE FUSE TERMINAL TYPE ACCOMMODATED INDICATES THE TYPE OF FUSE TERMINATIONS WHICH THE ITEM WILL ACCOMMODATE. SELECT REPLY CODE 10AN89 CSNNJ /D/ 04RADIUS,CIRCLE,BOLT,MOUNTING CENTER MOUNTING CENTER BOLT CIRCLE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CSNPJ 04ANGLE BETWEEN THIRD AND FOURTH KEY ANGLE BETWEEN THIRD AND FOURTH KEY NONE. 2D AND 1B MODE REPLY21AP381AC20 CSNQJ 04WIDTH,KEYWAY,MOUNTING MOUNTING KEYWAY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSNRJ 04ANGLE,TILT,FORWARD,BOOM BOOM FORWARD TILT ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSNSH /D/ 19CONFIGURATION PER POLE,TRIP RELEASE,INTERNAL INTERNAL TRIP RELEASE CONFIGURATION PER POLE THE BASIC INTERNAL ELECTRICAL CONFIGURATION OF THE TRIP MECHANISM PROVIDED FOR EACH POLE. 2D MODE REPLY 22AE972AP31 CSNTJ 04DIAMETER,OUTSIDE,NOMINAL,SECOND INTAKE SECOND INTAKE NOMINAL OUTSIDE DIAMETER A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE OUTSIDE DIAMETER. 1D AND 1B MODE REPLY11AA05 CSNWD /D/ 19RELATIONSHIP TO PRECEDING BRUSHES,THIRD BRUSH THIRD BRUSH RELATIONSHIP TO PRECEDING BRUSHES AN INDICATION OF WHETHER OR NOT THE THIRD BRUSH IS IDENTICAL TO THE PRECEDING BRUSHES. SELECT REPLY CODE 10AA37 CSNXD 19MEMBER FOR WHICH DESIGNED,BODY BODY MEMBER FOR WHICH DESIGNED AN INDICATION OF THE SPECIFIC PORTION OF THE BODY FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AK54 CSNYJ 04DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF NINTH DIAMETER DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF NINTH DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSNZJ 04ANGLE,CHAMFER,FIRST END FIRST END CHAMFER ANGLE NONE. REPLACED BY MRC CSYT WITH ISAC 0368. 2D AND 1B MODE REPLY21AP381AC20 CSPBB 10PERCENTAGE BY WEIGHT,CONTENT,ASPHALTENE,MAXIMUM MAXIMUM ASPHALTENE CONTENT PERCENTAGE BY WEIGHT A MEASUREMENT OF THE MAXIMUM ASPHALTENE CONTENT OF THE ITEM,EXPRESSED IN PERCENT BY WEIGHT. 1B MODE REPLY 0 CSPCJ 04DIAMETER,INSIDE,ACCOMMODATION HOLE ACCOMMODATION HOLE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSPDJ A19DOCUMENT AND CLASSIFICATION,SURFACE TREATMENT,HOLDER HOLDER SURFACE TREATMENT DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE HOLDER SURFACE TREATMENT MATERIAL. 2D AND 1A MODE REPLY21AP331AP39 CSPFJ 13THREAD DIAMETER,NOMINAL,HOLE HOLE NOMINAL THREAD DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CSPGJ 04DIAMETER,OUTSIDE,PRIMARY WASHER PRIMARY WASHER OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSPHJ /D/A12QUANTITY,CONTACT CONTACT QUANTITY THE NUMBER OF CONTACTS WHICH PROVIDE ELECTRICAL CONNECTION. 2D AND 1A MODE REPLY21AP551AP56 CSPJD 14SHAPE,EDGE,STARTING STARTING EDGE SHAPE THE PHYSICAL CONFIGURATION OF THE STARTING EDGE OF THE ITEM. SELECT REPLY CODE 10AP00 CSPKJ 10REACTANCE IN OHMS,ZCO,PLUS J PLUS J ZCO REACTANCE IN OHMS THE REACTANCE (X) OF THE COMPENSATOR IMPEDANCE WITH THE ROTOR OPEN (ZCO),EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 CSPLJ 04DISTANCE,OFFSET,LONGER,WAVEGUIDE WAVEGUIDE LONGER OFFSET DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CSPMH /D/ 18TYPE AND PUMP DESIGNATION,ELEMENT,PUMPING PUMPING ELEMENT TYPE AND PUMP DESIGNATION INDICATES THE TYPE OF PUMPING ELEMENT WHICH PRODUCES LOW PRESSURE WITHIN THE ITEM,AND THE PUMP DESIGNATION. 2D MODE REPLY 21AD043AA96 CSPNJ 04DIAMETER,INSIDE,NOMINAL,FIRST INTAKE FIRST INTAKE NOMINAL INSIDE DIAMETER A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE INSIDE DIAMETER. 1D AND 1B MODE REPLY11AA05 CSPPJ 04WIDTH,OVERALL,PLATE PLATE OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PLATE,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CSPQD 18TYPE,CONNECTION,SECOND DISCHARGE SECOND DISCHARGE CONNECTION TYPE INDICATES THE TYPE OF CONNECTION ON THE SECOND DISCHARGE. SELECT REPLY CODE 10AB76 CSPRJ 04WIDTH FOR WHICH DESIGNED,DRUM DRUM WIDTH FOR WHICH DESIGNED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE DRUM FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CSPSJ /D/ 10VOLTAGE IN VOLTS AND POLARITY,DC,POWER SOURCE POWER SOURCE DC VOLTAGE IN VOLTS AND POLARITY THE VALUE OF DIRECT CURRENT POTENTIAL FOR WHICH THE POWER SOURCE IS RATED,EXPRESSED IN VOLTS,AND ITS POLARITY. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AK221AC20 CSPTD 09MATERIAL,SHELL SHELL MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE SHELL IS FABRICATED. SELECT REPLY CODE 10MA01 CSPWJ 04ANGLE BETWEEN MOUNTING HOLE CENTERLINES ANGLE BETWEEN MOUNTING HOLE CENTERLINES NONE. 2D AND 1B MODE REPLY21AP381AC20 CSPXJ 04ANGLE,OFFSET,WRENCHING END WRENCHING END OFFSET ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSPYJ 04DIAMETER,STEP,LARGEST LARGEST STEP DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST STEP,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CSPZJ /D/ 04THICKNESS,OVERALL,ANGLE FASTENER ANGLE FASTENER OVERALL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CSQBJ 04DIAMETER,INSIDE,NOMINAL,FIRST DISCHARGE FIRST DISCHARGE NOMINAL INSIDE DIAMETER A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE INSIDE DIAMETER. 1D AND 1B MODE REPLY11AA05 CSQCJ 10VOLTAGE RATING IN VOLTS,MAXIMUM,AUXILIARY CONTACT AUXILIARY CONTACT MAXIMUM VOLTAGE RATING IN VOLTS THE HIGHEST VOLTAGE AT WHICH THE AUXILIARY CONTACTS ARE RATED FOR NORMAL OPERATION,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY12AN87 CSQDJ 04ANGLE,INSIDE,RIGHT RIGHT INSIDE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSQFD 11METHOD,INSTALLATION INSTALLATION METHOD THE MEANS BY WHICH THE ITEM IS INSTALLED. SELECT REPLY CODE 10AB89 CSQGD 19DATA,FURNISHED FURNISHED DATA INDICATES THE INFORMATION DESIGNED TO BE VISIBLY SHOWN. SELECT REPLY CODE 10AP58 CSQHB 13THREAD PITCH IN MILLIMETERS,END,FIRST FIRST END THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CSQJJ 04DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO THE ALTITUDE OF AN ISOSCELES TRIANGLE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO THE ALTITUDE OF AN ISOSCELES TRIANGLE THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE ALTITUDE OF AN ISOSCELES TRIANGLE. 2D AND 1B MODE REPLY21AA051AC20 CSQKJ 04WIDTH,SPAN SPAN WIDTH A LINEAR MEASUREMENT OF THE DISTANCE FROM ONE POINT TO THE OPPOSITE POINT OF THE SPAN. 2D AND 1B MODE REPLY21AA051AC20 CSQLJ 04ANGLE BETWEEN EXTERNAL KEY CENTERLINES ANGLE BETWEEN EXTERNAL KEY CENTERLINES NONE. 2D AND 1B MODE REPLY21AP381AC20 CSQMD 19ACCOMMODATION,MEMBER,MATING,ELECTRICAL CONNECTOR RECEPTACLE ELECTRICAL CONNECTOR RECEPTACLE MATING MEMBER ACCOMMODATION THE MATING MEMBER ACCOMMODATED BY THE ELECTRICAL CONNECTOR RECEPTACLE INCLUDED ON THE ITEM. SELECT REPLY CODE 10AN89 CSQNB /D/ 10CURRENT RATING IN AMPS,SHORT-CIRCUIT/INTERRUPT SHORT-CIRCUIT/INTERRUPT CURRENT RATING IN AMPS THE MAXIMUM RATED CURRENT AT WHICH THE ITEM WILL INTERRUPT OR SHORT CIRCUIT,EXPRESSED IN AMPERES. 1B MODE REPLY 0 CSQPJ 04DIAMETER,OUTSIDE,SECOND INTAKE FLANGE SECOND INTAKE FLANGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSQQJ /D/A12QUANTITY AND PUMP DESIGNATION,IMPELLER IMPELLER QUANTITY AND PUMP DESIGNATION THE NUMBER OF IMPELLERS INCLUDED ON THE ITEM,AND THE PUMP DESIGNATION. 1D AND 1A MODE REPLY13AA96 CSQRD 19FORM,ELEMENT,DIALYZER DIALYZER ELEMENT FORM THE SHAPE OR CONFIGURATION OF THE DIALYZER ELEMENT. SELECT REPLY CODE 10AC68 CSQSJ /D/ 10TIME PER POLE IN SECONDS,TRIP,ULTIMATE ULTIMATE TRIP TIME PER POLE IN SECONDS THE ULTIMATE TIME IN WHICH EACH POLE OF THE DEVICE MUST TRIP,EXPRESSED IN SECONDS. 2D AND 1B MODE REPLY21AC202AP31 CSQTJ A19FACILITY AND QUANTITY,CONNECTING,FLANGE FLANGE CONNECTING FACILITY AND QUANTITY THE TYPE AND NUMBER OF FACILITIES BY WHICH THE FLANGE IS CONNECTED. 1D AND 1A MODE REPLY13AM39 CSQWD 18TYPE FOR WHICH DESIGNED,OPERATION,TOOL TOOL OPERATION TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF TOOL OPERATION FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AN38 CSQXA 19CODE AND MODEL NUMBER,MANUFACTURER,PRIME MOVER PRIME MOVER MANUFACTURER CODE AND MODEL NUMBER THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE MANUFACTURER OF THE PRIME MOVER FURNISHED WITH THE ITEM AND THE MODEL NUMBER. 1A MODE REPLY 0 CSQYJ 05DIRECTION AND ENERGIZING STROKE IN ANGULAR DEG,ROTATION ROTATION DIRECTION AND ENERGIZING STROKE IN ANGULAR DEG THE DIRECTION IN WHICH AN ITEM IS DESIGNED TO ROTATE,WHEN VIEWED AXIALLY AND THE ANGULAR DEGREE OF TRAVEL FROM THE DE-ENERGIZED TO THE ENERGIZED POSITION. 1D AND 1B MODE REPLY13AA38 CSQZJ 04LENGTH,STEP,FIRST END FIRST END STEP LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSRBJ 04ANGLE,KEY,PREBENT,INTERNAL INTERNAL PREBENT KEY ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSRCJ 04ANGLE,BEVEL,BOSS BOSS BEVEL ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSRDJ 04DIAMETER,OUTSIDE,NOMINAL,SECOND DISCHARGE SECOND DISCHARGE NOMINAL OUTSIDE DIAMETER A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE OUTSIDE DIAMETER. 1D AND 1B MODE REPLY11AA05 CSRFJ 04DIAMETER,OUTSIDE,FASTENER FASTENER OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSRGJ 04WIDTH,MAJOR,FIRST END KEYWAY FIRST END KEYWAY MAJOR WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSRHJ 04DIAMETER,OUTSIDE,FIRST INTAKE FLANGE FIRST INTAKE FLANGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSRJD 19FEATURE,DISTRIBUTION,LIGHT INTENSITY LIGHT INTENSITY DISTRIBUTION FEATURE AN INDICATION OF THE LIGHT INTENSITY DISTRIBUTION FEATURE PROVIDED. SELECT REPLY CODE 10AE84 CSRKJ 04WIDTH,WAVEGUIDE WAVEGUIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSRLJ /D/ 13THREAD SIZE,NOMINAL,CLEANOUT CLEANOUT NOMINAL THREAD SIZE NONE. 1D AND 1B MODE REPLY11AA05 CSRMJ 04LENGTH,LEG,FIRST,WAVEGUIDE WAVEGUIDE FIRST LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSRNJ 04LENGTH,LEG,FIFTH,WAVEGUIDE WAVEGUIDE FIFTH LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSRPD 04SIZE,SECTION,TUBULAR POINT TUBULAR POINT SECTION SIZE DESIGNATES THE SIZE OF THE TUBULAR POINT SECTION. SELECT REPLY CODE 10AF81 CSRQJ 04DIAMETER,ADAPTER ADAPTER DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSRRJ 04THICKNESS,SEAL SEAL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CSRSJ /D/ 04WIDTH AND SHAFT DESIGNATION,SLOT SLOT WIDTH AND SHAFT DESIGNATION NONE. 3D AND 1B MODE REPLY31AA051AC202AD87 CSRTJ 10CAPACITY CAPACITY A MEASUREMENT OF THE CAPACITY OF AN ITEM. 2D AND 1B MODE REPLY22AG671AC20 CSRWJ /D/ 04DIAMETER AND MOUNTING FACILITY,BUSHING BUSHING DIAMETER AND MOUNTING FACILITY NONE. 3D AND 1B MODE REPLY31AA051AC202AP26 CSRXJ /D/ 10FLOW RATE AND PUMP DESIGNATION,DISCHARGE,MAXIMUM MAXIMUM DISCHARGE FLOW RATE AND PUMP DESIGNATION THE MAXIMUM DISCHARGE FLOW FOR WHICH AN ITEM IS RATED,AND THE PUMP DESIGNATION. 2D AND 1B MODE REPLY22AG203AA96 CSRYH /D/ 19REMOVABILITY,CONTACT CONTACT REMOVABILITY AN INDICATION OF WHETHER OR NOT THE CONTACT/S/ IS REMOVABLE. 3D MODE REPLY 31AP551AP561AC29 CSRZJ 04HEIGHT,INSIDE,SEAL SEAL INSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CSSBJ 04DISTANCE,PIN CENTER TO HANDLE END PIN CENTER TO HANDLE END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CSSCB /D/ 13THREAD PITCH IN MILLIMETERS,HOLE,CONCENTRIC CONCENTRIC HOLE THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE CONCENTRIC HOLE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CSSDJ 04DIAMETER,STEP,SHAFT SHAFT STEP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSSFJ 04WIDTH,OUTSIDE,VANE VANE OUTSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSSGJ 04DIAMETER,INSIDE,NOMINAL,SECOND INTAKE SECOND INTAKE NOMINAL INSIDE DIAMETER A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE INSIDE DIAMETER. 1D AND 1B MODE REPLY11AA05 CSSHJ /D/ 04DIAMETER,HOLE,MOUNTING,UNTHREADED UNTHREADED MOUNTING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CSSJH /D/ 13THREAD DIRECTION-LOCATION AND PUMP DESIGNATION THREAD DIRECTION-LOCATION AND PUMP DESIGNATION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY,ITS LOCATION ON THE ITEM,AND THE PUMP DESIGNATION. 3D MODE REPLY 33AA383AN733AA96 CSSKJ /D/ 04DIAMETER OF BRUSH PART,THIRD BRUSH THIRD BRUSH DIAMETER OF BRUSH PART NONE. 2D AND 1B MODE REPLY21AA051AC20 CSSLJ A19FUNCTION AND QUANTITY,DESIGN DESIGN FUNCTION AND QUANTITY THE BASIC PURPOSE AND NUMBER OF FUNCTIONS OF THE DEVICE,MODIFIED BY ITS INTENDED USE. 1D AND 1A MODE REPLY13AP43 CSSMJ 04ANGLE,COUNTERSINK,MOUNTING HOLE MOUNTING HOLE COUNTERSINK ANGLE THE INCLUDED ANGLE OF THE MOUNTING HOLE COUNTERSINK. 2D AND 1B MODE REPLY21AP381AC20 CSSNJ 10SETTING AND FUNCTION,INTENSITY,LIGHT LIGHT INTENSITY SETTING AND FUNCTION THE INTENSITY OF LIGHT AT WHICH THE ITEM IS SET AND ITS FUNCTION. 2D AND 1B MODE REPLY21AP251AE28 CSSPD 19RELATIONSHIP TO FIRST LEG,SECOND LEG SECOND LEG RELATIONSHIP TO FIRST LEG AN INDICATION OF WHETHER OR NOT THE SECOND LEG IS IDENTICAL TO THE FIRST LEG. SELECT REPLY CODE 10AF63 CSSQJ 04ANGLE,FIRST LEG FIRST LEG ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSSRJ 04ANGLE,SECOND LEG SECOND LEG ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSSSD 18TYPE,OUTPUT,AUXILIARY AUXILIARY OUTPUT TYPE INDICATES THE TYPE OF AUXILIARY OUTPUT. SELECT REPLY CODE 10AC58 CSSWJ 04WIDTH,MINOR,FIRST END KEYWAY FIRST END KEYWAY MINOR WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSSXJ 10CURRENT RATING AND TYPE IN AMPS,SWITCH SWITCH CURRENT RATING AND TYPE IN AMPS THE AMOUNT OF CURRENT,EXPRESSED IN AMPERES,AND THE TYPE FOR WHICH THE SWITCH IS RATED. 1D AND 1B MODE REPLY12AN87 CSSYJ 04ANGLE,OFFSET,FIRST LEG FIRST LEG OFFSET ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSSZJ 04ANGLE,OFFSET,SECOND LEG SECOND LEG OFFSET ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSTBD /D/ 07REVERSIBILITY,CHAIN,CROSS CROSS CHAIN REVERSIBILITY AN INDICATION OF WHETHER OR NOT THE CROSS CHAIN IS REVERSIBLE. SELECT REPLY CODE 10AF62 CSTCD 01COLOR,LEGEND,TRANSMITTED TRANSMITTED LEGEND COLOR THE HUE OR TINT OF THE TRANSMITTED LEGEND. SELECT REPLY CODE 10AD06 CSTDL 16STYLE,SHAPE,FIRST INTAKE FLANGE FIRST INTAKE FLANGE SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE FLANGE. 1L MODE REPLY 0 CSTFJ /D/ 04THICKNESS AT MOUNTING BOLT OPENING AND SEQUENCE DESIGNATION THICKNESS AT MOUNTING BOLT OPENING AND SEQUENCE DESIGNATION A MEASUREMENT THROUGH THE ITEM AT THE HOLE OR SLOT DESIGNED TO ACCOMMODATE A BOLT OR THE LIKE AND THE MOUNTING SEQUENCE. 3D AND 1B MODE REPLY31AA051AC202AP26 CSTGJ /D/ 04DISTANCE,CENTER TO CENTER,RIM RIM CENTER TO CENTER DISTANCE THE DISTANCE FROM RIM CENTER TO RIM CENTER. 2D AND 1B MODE REPLY21AA051AC20 CSTHJ 04DIAMETER,INSIDE,NOMINAL,SECOND DISCHARGE SECOND DISCHARGE NOMINAL INSIDE DIAMETER A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE INSIDE DIAMETER. 1D AND 1B MODE REPLY11AA05 CSTJD 05DIRECTION,READING,SCALE SCALE READING DIRECTION INDICATES THE READING DIRECTION OF THE SCALE. SELECT REPLY CODE 10AB50 CSTKA 19NUMBER,CLASSIFICATION,COPPER CORROSION COPPER CORROSION CLASSIFICATION NUMBER AN INDICATION OF THE ASTM COPPER CORROSION CLASSIFICATION IN ACCORDANCE WITH IP 154,ASTM D130 AT 100 DEG CELSIUS. 1A MODE REPLY 0 CSTLJ /D/A18TYPE AND LOCATION DESIGNATOR,BOSS BOSS TYPE AND LOCATION DESIGNATOR INDICATES THE TYPE OF BOSS INCLUDED ON THE ITEM AND ITS LOCATION. 1D AND 1A MODE REPLY12AP52 CSTMJ 04ANGLE,RECESS RECESS ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSTNJ 04LENGTH,OVERALL,EYELET EYELET OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSTPJ 04ANGLE,CHAMFER,SECOND END SECOND END CHAMFER ANGLE NONE. REPLACED BY MRC CSYT WITH ISAC 0368. 2D AND 1B MODE REPLY21AP381AC20 CSTQJ 04ANGLE,INNER FACE TO OUTER FACE,RIGHT TOP RIGHT TOP INNER FACE TO OUTER FACE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSTRB /D/ 10CONTENT IN PERCENT AT 20 DEG CELSIUS,ALCOHOL,EUROPEAN PHARMACOPEIA EUROPEAN PHARMACOPEIA ALCOHOL CONTENT IN PERCENT AT 20 DEG CELSIUS THE PERCENTAGE,BY VOLUME,OF ALCOHOL AS SPECIFIED BY THE EUROPEAN PHARMACOPEIA,EXPRESSED AT 20 DEGREES CELSIUS. 1B MODE REPLY 0 CSTSD 19USE,WOOD PRODUCTS,TYPICAL TYPICAL WOOD PRODUCTS USE THE REQUIRED PURPOSE OR APPLICATION OF THE TYPICAL WOOD PRODUCTS FOR WHICH THE ITEM IS INTENDED. SELECT REPLY CODE 10AP62 CSTTH 19SPECIES AND GRADE,PLYWOOD PLYWOOD SPECIES AND GRADE AN INDICATION OF THE PLYWOOD SPECIES AND GRADE OF THE ITEM. 2D MODE REPLY 22AM002AP63 CSTWJ A19GROUP AND LOCATION,SPECIES,WOOD WOOD SPECIES GROUP AND LOCATION THE GROUP BY WHICH THE WOOD SPECIES IS IDENTIFIED AND ITS LOCATION ON THE ITEM. 1D AND 1A MODE REPLY11AP64 CSTXJ 04DIAMETER AND LOCATION DIAMETER AND LOCATION THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE,AND THE LOCATION ON THE ITEM. 3D AND 1B MODE REPLY31AA051AC203AN73 CSTYJ 10CIRCUMFERENCE AND LOCATION,MINIMUM MINIMUM CIRCUMFERENCE AND LOCATION THE MINIMUM DISTANCE MEASURED AROUND THE OUTSIDE OF AN ITEM,AND THE LOCATION. 2D AND 1B MODE REPLY21AA053AN73 CSTZD 19USAGE,SERVICE SERVICE USAGE THE APPLICATION FOR WHICH THE ITEM IS INTENDED. SELECT REPLY CODE 10AN66 CSWBJ A18TYPE AND QUANTITY,COIL COIL TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF COILS PROVIDED. 1D AND 1A MODE REPLY13AK03 CSWCL 16STYLE,SHAPE,FIRST DISCHARGE FLANGE FIRST DISCHARGE FLANGE SHAPE STYLE THE STYLE DESIGNATION INDICATION THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE FLANGE. 1L MODE REPLY 0 CSWDJ 04ANGLE BETWEEN EDGE AND FIRST HOLE CENTER,LEG,FIRST FIRST LEG ANGLE BETWEEN EDGE AND FIRST HOLE CENTER NONE. 2D AND 1B MODE REPLY21AP381AC20 CSWFJ /D/ 04ANGLE BETWEEN EDGE AND SECOND HOLE CENTER,LEG,FIRST FIRST LEG ANGLE BETWEEN EDGE AND SECOND HOLE CENTER NONE. 2D AND 1B MODE REPLY21AP381AC20 CSWGJ /D/ 04ANGLE BETWEEN EDGE AND FIRST HOLE CENTER,LEG,SECOND SECOND LEG ANGLE BETWEEN EDGE AND FIRST HOLE CENTER NONE. 2D AND 1B MODE REPLY21AP381AC20 CSWHJ /D/ 04ANGLE BETWEEN EDGE AND SECOND HOLE CENTER,LEG,SECOND SECOND LEG ANGLE BETWEEN EDGE AND SECOND HOLE CENTER NONE. 2D AND 1B MODE REPLY21AP381AC20 CSWJA 12QUANTITY,WORD WORD QUANTITY THE NUMBER OF WORDS,CONSISTING OF ONE OR MORE BITS,FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 CSWKJ 10PRESSURE,BURST BURST PRESSURE THE MINIMUM INTERNAL PRESSURE AT WHICH THE ITEM CAN BE EXPECTED TO RUPTURE. 2D AND 1B MODE REPLY22AL152AG20 CSWLH 04SIZE,WIRE,CONDUCTOR CONDUCTOR WIRE SIZE THE SIZE WIRE USED IN THE CONDUCTOR. 2D MODE REPLY 21AA442AP07 CSWMD 17SURFACE TREATMENT,SHELL SHELL SURFACE TREATMENT THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SHELL SURFACE/S/ AND CANNOT BE WIPED OFF. SELECT REPLY CODE 10SF01 CSWNJ 04LENGTH,ACCOMMODATION,BODY MOUNTING HOLE,SHORTEST SHORTEST BODY MOUNTING HOLE ACCOMMODATION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSWPJ 10VOLTAGE RATING AND TYPE IN VOLTS,SWITCH SWITCH VOLTAGE RATING AND TYPE IN VOLTS THE VOLTAGE,EXPRESSED IN VOLTS,AND CURRENT TYPE FOR WHICH THE SWITCH IS RATED. 1D AND 1B MODE REPLY12AN87 CSWQJ 04DIAMETER,MINOR,TAPERED BRUSH PART,FIRST BRUSH FIRST BRUSH TAPERED BRUSH PART MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSWRJ 10VALUE,DENSITY DENSITY VALUE THE QUOTIENT OF THE PRODUCT MASS BY ITS VOLUME AT A SPECIFIED TEMPERATURE. 2D AND 1B MODE REPLY22AB491AC20 CSWSD 11METHOD,DISPLAY,NUMERAL NUMERAL DISPLAY METHOD THE MEANS BY WHICH THE DISPLAY OF THE NUMERAL IS PROVIDED. SELECT REPLY CODE 10AJ91 CSWTJ A19READOUT,NUMERAL NUMERAL READOUT THE READOUT OF THE NUMERALS DISPLAYED BY THE ITEM. 1D AND 1A MODE REPLY11AC20 CSWWJ 10ROTATION DIRECTION AND MAXIMUM SPEED IN RPM,SHAFT SHAFT ROTATION DIRECTION AND MAXIMUM SPEED IN RPM THE DIRECTION THE SHAFT TURNS AS VIEWED FROM THE DRIVE END AND THE MAXIMUM SPEED,EXPRESSED IN REVOLUTIONS PER MINUTE. 1D AND 1B MODE REPLY11AC84 CSWXA /D/ 13THREAD QUANTITY PER INCH,INTERNAL,HEAD HEAD INTERNAL THREAD QUANTITY PER INCH THE NUMBER OF INTERNAL THREADS ON THE HEAD PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CSWYJ /D/ 04DISTANCE,CENTER TO CENTER,HOLE,PISTON END PISTON END HOLE CENTER TO CENTER DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CSWZJ /D/ 04DISTANCE,CENTER TO CENTER,HOLE,CYLINDER END CYLINDER END HOLE CENTER TO CENTER DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CSXBJ 04ANGLE,CHAMFER,KEY KEY CHAMFER ANGLE THE INCLUDED ANGLE OF THE BEVELED EDGE OF THE KEY. REPLACED BY MRC CSYT WITH ISAC 0368. 2D AND 1B MODE REPLY21AP381AC20 CSXCD 18TYPE,RETRACTOR RETRACTOR TYPE INDICATES THE TYPE OF RETRACTOR PROVIDED. SELECT REPLY CODE 10AL19 CSXDB 04THICKNESS IN MICRONS,MEMBRANE MEMBRANE THICKNESS IN MICRONS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE MEMBRANE,IN DISTINCTION FROM LENGTH OR WIDTH,EXPRESSED IN MICRONS/MICROMETERS/. 1B MODE REPLY 0 CSXFJ 10VOLTAGE RATING AND TYPE AT SPECIFIED TEMP,OPERATING OPERATING VOLTAGE RATING AND TYPE AT SPECIFIED TEMP THE AMOUNT AND TYPE OF VOLTAGE REQUIRED AT DESIGNATED TEMPERATURE TO BE APPLIED TO THE INPUT OR ENERGIZING ELEMENT OF THE ITEM TO ENSURE NORMAL OPERATION OF THE SWITCHING ELEMENTS. 3D AND 1B MODE REPLY32AN862AN872AP15 CSXGJ 04ANGLE,OFFSET OFFSET ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSXHJ 04DIAMETER,SHANK,STUD END STUD END SHANK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSXJA /D/ 12QUANTITY,FAN-OUT FAN-OUT QUANTITY THE NUMBER OF PARALLEL LOADS THAT CAN BE DRIVEN FROM ONE OUTPUT NODE OF A LOGIC CIRCUIT. 1A MODE REPLY 0 CSXKJ 04THICKNESS ACCOMMODATED,NOMINAL,MATERIAL MATERIAL NOMINAL THICKNESS ACCOMMODATED THE NOMINAL THICKNESS OF THE MATERIAL THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 CSXLJ 19FINISH,SURFACE,BEARING BEARING SURFACE FINISH DESIGNATES THE SPECIFIC ROUGHNESS RATING OF THE BEARING SURFACE,REPRESENTING THE ARITHMETIC AVERAGE DEVIATION OF THE SURFACE FROM THE MEANLINE IN PROFILE. 1D AND 1B MODE REPLY11AE86 CSXML 16STYLE,SHAPE,SECOND INTAKE FLANGE SECOND INTAKE FLANGE SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE FLANGE. 1L MODE REPLY 0 CSXNB /D/ 10CAPACITY IN LITERS PER MINUTE,WATER,MAXIMUM MAXIMUM WATER CAPACITY IN LITERS PER MINUTE THE MAXIMUM AMOUNT OF WATER FOR WHICH THE ITEM IS RATED,EXPRESSED IN LITERS PER MINUTE. 1B MODE REPLY 0 CSXQB 10CAPACITY IN CUBIC METERS PER MINUTE,AIR,MAXIMUM MAXIMUM AIR CAPACITY IN CUBIC METERS PER MINUTE THE MAXIMUM AMOUNT OF AIR FOR WHICH THE ITEM IS RATED,EXPRESSED IN CUBIC METERS PER MINUTE. 1B MODE REPLY 0 CSXRJ 04ANGLE BETWEEN FOURTH AND FIFTH KEY ANGLE BETWEEN FOURTH AND FIFTH KEY NONE. 2D AND 1B MODE REPLY21AP381AC20 CSXSJ 04ANGLE ANGLE NONE. 1D AND 1B MODE REPLY11AA05 CSXTJ 04DISTANCE FROM MOUNTING HOLE CENTER TO MOUNTING END DISTANCE FROM MOUNTING HOLE CENTER TO MOUNTING END NONE. 1D AND 1B MODE REPLY11AA05 CSXWB /D/ 10CANDLEPOWER IN LUMEN,LAMP LAMP CANDLEPOWER IN LUMEN THE CANDLEPOWER,OR MEASUREMENT OF LUMINOUS INTENSITY FOR WHICH THE LAMP IS RATED,EXPRESSED IN LUMENS. 1B MODE REPLY 0 CSXYJ 04DIAMETER,OUTSIDE,CAP CAP OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CSXZJ /D/ 04ANGLE,BENT BENT ANGLE NONE. 1D AND 1B MODE REPLY11AA05 CSYBJ 04DIAMETER,HOLE,TURNLOCK MOUNTING TURNLOCK MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSYCA /D/ 12QUANTITY,CAP CAP QUANTITY THE NUMBER OF CAPS INCLUDED IN THE ITEM. 1A MODE REPLY 0 CSYDA /D/ 12QUANTITY PER CENTIMETER,CORRUGATION CORRUGATION QUANTITY PER CENTIMETER THE NUMBER OF CORRUGATIONS PER CENTIMETER. 1A MODE REPLY 0 CSYFJ A19CONFIGURATION AND QUANTITY,DESIGN DESIGN CONFIGURATION AND QUANTITY THE BASIC SHAPE,APPLICATION AND SURFACE FEATURES OF AN ITEM,AND THE NUMBER OF EACH. 1D AND 1A MODE REPLY12AA43 CSYGJ T10RANGE,MEASUREMENT,SCALE SCALE MEASUREMENT RANGE THE MINIMUM AND MAXIMUM NUMERIC VALUES REPRESENTING THE TYPE OF SCALE MEASUREMENT. 1D AND 1F MODE REPLY12AJ20 CSYHJ 04LENGTH,OVERALL,BULB BULB OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CSYJJ A18TYPE AND QUANTITY,POINTER/PEN POINTER/PEN TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF POINTER(S) OR PEN(S). 2D AND 1A MODE REPLY23AL973AJ44 CSYKJ 04DIAMETER,OUTSIDE,FIRST DISCHARGE FLANGE FIRST DISCHARGE FLANGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSYLJ 10POWER RATING,PRIME MOVER PRIME MOVER POWER RATING THE RATED POWER OF THE PRIME MOVER. 1D AND 1B MODE REPLY11AC33 CSYMJ 19FINISH,SURFACE SURFACE FINISH DESIGNATES THE SPECIFIC SURFACE ROUGHNESS RATING,REPRESENTING THE ARITHMETIC AVERAGE DEVIATION OF THE SURFACE FROM THE MEANLINE IN PROFILE. 1D AND 1B MODE REPLY11AE86 CSYNJ /D/ 04DIAMETER,MINOR,TAPERED END TAPERED END MINOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CSYPD 18TYPE FOR WHICH DESIGNED,LAST LAST TYPE FOR WHICH DESIGNED INDICATES THE LAST TYPE FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AD34 CSYQD /D/ 19ELASTICITY ELASTICITY AN INDICATION OF WHETHER OR NOT ELASTICITY IS INCLUDED IN THE ITEM. SELECT REPLY CODE 10AA49 CSYRL 16STYLE,SOCKET,SEPARABLE SEPARABLE SOCKET STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SEPARABLE SOCKET. 1L MODE REPLY 0 CSYSJ /D/ 04TAPER AND LOCATION TAPER AND LOCATION NONE. 2D AND 1B MODE REPLY21AB393AJ91 CSYTJ 04ANGLE,CHAMFER CHAMFER ANGLE THE INCLUDED ANGLE OF THE CHAMFER(S). 2D AND 1B MODE REPLY21AP381AC20 CSYWD 18TYPE,ELEMENT,CONNECTING CONNECTING ELEMENT TYPE INDICATES THE TYPE OF CONNECTING ELEMENT FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AC52 CSYXJ 12DIAMETER AND QUANTITY,HOLE,NOMINAL NOMINAL HOLE DIAMETER AND QUANTITY THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR HOLE,AND TERMINATES AT THE CIRCUMFERENCE,AND THE NUMBER OF HOLES. 2D AND 1B MODE REPLY21AA053AP65 CSYYL 16STYLE,SHAPE,SECOND DISCHARGE FLANGE SECOND DISCHARGE FLANGE SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE FLANGE. 1L MODE REPLY 0 CSYZJ /D/ 04DISTANCE BETWEEN HOLES,CENTER TO CENTER,NOMINAL NOMINAL CENTER TO CENTER DISTANCE BETWEEN HOLES THE NOMINAL CENTER TO CENTER DISTANCE BETWEEN HOLES ON THE ITEM. 1D AND 1B MODE REPLY11AA05 CSZBJ 04ANGLE,TAPER,STUD STUD TAPER ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSZCJ 04DIAMETER,INLET,MAIN TRUNK MAIN TRUNK INLET DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSZDA 19LOAD INDEX AND SPEED SYMBOL,TIRE TIRE LOAD INDEX AND SPEED SYMBOL A NUMERIC INDEX WHICH INDICATES THE MAXIMUM LOAD THE TIRE WILL CARRY AND THE ALPHA OR ALPHANUMERIC SPEED SYMBOL AT WHICH THE TIRE WILL CARRY THIS LOAD UNDER SERVICE CONDITIONS SPECIFIED BY THE TIRE MANUFACTURER. 1A MODE REPLY 0 CSZFJ 04DIAMETER,OUTSIDE,SECOND DISCHARGE FLANGE SECOND DISCHARGE FLANGE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CSZGJ 04LENGTH,TERMINAL,FIRST END FIRST END TERMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CSZHA /D/ 19CHARACTERISTIC,RENDITION,LEVEL OF COLOR LEVEL OF COLOR RENDITION CHARACTERISTIC THE RELATIONSHIP BETWEEN THE COLOR OF AN OBJECT EXPOSED TO A REFERENCE LIGHT AND THE COLOR OF AN OBJECT UNDER THE LIGHT TO BE DESCRIBED. 1A MODE REPLY 0 CSZJA /D/ 03DESIGNATION,SIZE,TAPER PIN,SECURING HOLE ACCOMMODATED SECURING HOLE ACCOMMODATED TAPER PIN SIZE DESIGNATION THE SIZE DESIGNATION FOR THE TAPER PIN ACCOMMODATED BY A SECURING HOLE. 1A MODE REPLY 0 CSZKJ /D/ 04DIAMETER,OVERALL OVERALL DIAMETER PLEASE USE MRC ADAV IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 CSZLJ 04TAPER,SLEEVE SLEEVE TAPER THE AMOUNT OF TAPER OF THE SLEEVE PER MEASUREMENT SCALE. 1D AND 1B MODE REPLY12AG20 CSZMJ 10CAPACITY FOR WHICH DESIGNED,CUP CUP CAPACITY FOR WHICH DESIGNED THE CAPACITY OF THE CUP FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY12AG67 CSZNJ /D/ 10VOLTAGE RATING AND TYPE PER POWDER SOURCE,EXTERNAL EXTERNAL VOLTAGE RATING AND TYPE PER POWDER SOURCE THE LEVEL OF EXTERNAL ELECTRICAL POTENTIAL AND TYPE OF CURRENT,PER POWER SOURCE,FOR WHICH THE ITEM IS DESIGNED. 4D AND 1B MODE REPLY41AB631AC202AN872AP27 CSZPJ 04LENGTH UNDER LOAD,SPRING SPRING LENGTH UNDER LOAD THE SPECIFIC EXTENDED OR COMPRESSED SPRING LENGTH UNDER MAXIMUM LOAD. 2D AND 1B MODE REPLY21AA051AC20 CSZQJ 04LENGTH,TERMINAL,SECOND END SECOND END TERMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CSZRJ 04WIDTH ACROSS FLATS,NUT NUT WIDTH ACROSS FLATS NONE. 1D AND 1B MODE REPLY11AA05 CSZSJ 04DIAMETER EXCLUDING COLLAR,OUTSIDE OUTSIDE DIAMETER EXCLUDING COLLAR NONE. 2D AND 1B MODE REPLY21AA051AC20 CSZTJ 04ANGLE,TILT,BACKWARD,BOOM BOOM BACKWARD TILT ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CSZWJ 04DIAMETER,FLANGE,MOUNTING MOUNTING FLANGE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CSZXJ 04TAPER,GRIP GRIP TAPER THE AMOUNT OF TAPER OF THE GRIP PER MEASUREMENT SCALE. 1D AND 1B MODE REPLY12AG20 CSZYJ 04DISTANCE ACROSS WRENCHING SURFACE FLATS DISTANCE ACROSS WRENCHING SURFACE FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 CSZZJ 04ANGLE,CHAMFER,RIGHT CORNER,INSIDE INSIDE RIGHT CORNER CHAMFER ANGLE NONE. REPLACED BY MRC CSYT WITH ISAC 0368. 2D AND 1B MODE REPLY21AP381AC20 CTBBD 19SUBSTANCE,COATING COATING SUBSTANCE INDICATES THE SUBSTANCE USED TO COAT THE ITEM. SELECT REPLY CODE 10AG56 CTBCJ A19DOCUMENT AND CLASSIFICATION,SURFACE TREATMENT,SHELL SHELL SURFACE TREATMENT DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE THAT IDENTIFIES THE SHELL SURFACE TREATMENT MATERIAL. 2D AND 1A MODE REPLY21AP331AP39 CTBDJ /D/ 10IMPEDANCE RATING PER FUNCTION IMPEDANCE RATING PER FUNCTION THE TOTAL OPPOSITION /RESISTIVE AND REACTIVE/ PER FUNCTION,WHICH THE ITEM OFFERS TO AN ALTERNATING CURRENT LOAD. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 3D AND 1B MODE REPLY32AN861AC202AH19 CTBFJ /D/ 04HEIGHT AND POSITION,OVERALL,LENS LENS OVERALL HEIGHT AND POSITION NONE. 3D AND 1B MODE REPLY31AA051AC202AK17 CTBGJ /D/ 04DIAMETER AND SEQUENCE DESIGNATION,HOLE,MOUNTING MOUNTING HOLE DIAMETER AND SEQUENCE DESIGNATION NONE. 3D AND 1B MODE REPLY31AA051AC202AP26 CTBHJ /D/ 10VOLTAGE RATING AND TYPE PER POLE IN VOLTS,TRIP COIL,AUXILIARY AUXILIARY TRIP COIL VOLTAGE RATING AND TYPE PER POLE IN VOLTS THE VOLTAGE,EXPRESSED IN VOLTS,AND CURRENT TYPE REQUIRED TO OPERATE EACH POLE OF THE AUXILIARY TRIP ACTUATOR. 3D AND 1B MODE REPLY32AN871AC202AP31 CTBJL 16STYLE,FACE,FIRST INTAKE FLANGE FIRST INTAKE FLANGE FACE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FLANGE FACE. 1L MODE REPLY 0 CTBKJ 04WIDTH OF BRUSH PART,BRUSH,SINGLE SINGLE BRUSH WIDTH OF BRUSH PART NONE. 2D AND 1B MODE REPLY21AA051AC20 CTBLJ T10RANGE,UNIT,SCALE GRADUATION SCALE GRADUATION UNIT RANGE INDICATES THE RANGE OF THE INCREMENTS OF MEASURE ON THE SCALE. 1D AND 1F MODE REPLY12AG67 CTBMJ 04LENGTH,STEP,SECOND END SECOND END STEP LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTBNB 04ANGLE IN DEG,PORT TO CABLE RECEPTACLE PORT TO CABLE RECEPTACLE ANGLE IN DEG THE ANGLE OF THE CABLE RECEPTACLE IN RELATION TO THE PORT,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CTBPJ 04LENGTH,TIP,SHAFT SHAFT TIP LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE SHAFT TIP, IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CTBQB 10PERCENTAGE BY VOLUME,CONTENT,OLEFINS,MAXIMUM MAXIMUM OLEFINS CONTENT PERCENTAGE BY VOLUME A MEASUREMENT OF THE MAXIMUM OLEFINS CONTENT OF THE ITEM,EXPRESSED IN PERCENT BY VOLUME. 1B MODE REPLY 0 CTBRJ 04ANGLE,INSIDE,LEFT BOTTOM LEFT BOTTOM INSIDE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CTBSA /D/ 13THREAD TOLERANCE CLASS,HOLE,CONCENTRIC CONCENTRIC HOLE THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITIONS AND GRADES OF A CONCENTRIC HOLE THREAD. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1A MODE REPLY 0 CTBTJ 04LENGTH,RECEPTACLE,POSITIVE LOCK POSITIVE LOCK RECEPTACLE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTBWJ T10RANGE,LOAD RATING,VIBRATION MOUNT VIBRATION MOUNT LOAD RATING RANGE THE RATED LOAD RANGE THE ITEM IS DESIGNED TO SUPPORT WHILE RETAINING ITS VIBRATION AND SHOCK ISOLATION CHARACTERISTICS. 1D AND 1F MODE REPLY12AN75 CTBYJ 04DIAMETER,COUNTERSINK,FIRST END FIRST END COUNTERSINK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTBZJ 04TAPER,REAMER REAMER TAPER THE AMOUNT OF TAPER OF THE REAMER PER SPECIFIC MEASUREMENT SCALE. 2D AND 1B MODE REPLY22AG201AC20 CTCBA 19LEGEND,LENS LENS LEGEND AN INDICATION OF THE LEGEND AFFIXED TO OR STAMPED ON THE LENS EXCLUDING PART NUMBER. 1A MODE REPLY 0 CTCCJ 04DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF SIXTH DIAMETER DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF SIXTH DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTCDJ /D/ 04SIZE,CROSS SECTION,SMALLEST SMALLEST CROSS SECTION SIZE NONE. 2D AND 1B MODE REPLY21AA051AC20 CTCFJ 10VALUE,HEAT OF COMBUSTION,MINIMUM MINIMUM HEAT OF COMBUSTION VALUE THE NUMBER OF THERMAL UNITS WHICH IS RELEASED BY COMBUSTION OF THE MASS UNIT OF THE FUEL (FORMED,UNCONDENSED WATER) IN OXYGEN. 1D AND 1B MODE REPLY12AG20 CTCGJ 04ANGLE,OUTSIDE,RIGHT RIGHT OUTSIDE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CTCHJ /D/ 04WIDTH OF BRUSH PART,BRUSH,FIRST FIRST BRUSH WIDTH OF BRUSH PART NONE. 2D AND 1B MODE REPLY21AA051AC20 CTCJL 16STYLE,FLANGE FLANGE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FLANGE. 1L MODE REPLY 0 CTCKJ 10COMPOSITION IN PERCENT,CHEMICAL,DEPOSITED FILLER METAL DEPOSITED FILLER METAL CHEMICAL COMPOSITION IN PERCENT AN INDICATION OF THE PROPORTION OF THE ELEMENT(S) OF THE DEPOSITED FILLER METAL,EXPRESSED IN PERCENT. 2D AND 1B MODE REPLY23AN411AC20 CTCLD /D/ 07FEATURE,ATTACHMENT,FLOOR FLOOR ATTACHMENT FEATURE AN INDICATION OF WHETHER OR NOT A FLOOR ATTACHMENT FEATURE IS PROVIDED. SELECT REPLY CODE 10AB22 CTCMJ 04LENGTH,KEYWAY,MOUNTING MOUNTING KEYWAY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTCNJ 10OPERATING RATING,ELECTRICAL,MINIMUM DIFFERENTIAL MINIMUM DIFFERENTIAL ELECTRICAL OPERATING RATING THE LOWEST NET AMOUNT OF THE SPECIFIED ENERGIZING ELECTRICAL CHARACTERISTIC NECESSARY FOR THE NORMAL FUNCTIONING OF THE RELAY. THE NET VALUE BEING THE DIFFERENCE BETWEEN MULTIPLE OR OPPOSED INPUT ELEMENTS DURING NORMAL OPERATION. 1D AND 1B MODE REPLY12AN86 CTCPB /D/ 10OUTPUT IN CUBIC INCHES OF AIR PER MINUTE,AERATOR,MAXIMUM MAXIMUM AERATOR OUTPUT IN CUBIC INCHES OF AIR PER MINUTE THE MAXIMUM AERATOR DELIVERY IN CUBIC INCHES OF AIR PER MINUTE. 1B MODE REPLY 0 CTCQH /D/ 18TYPE,CONTACT CONTACT TYPE INDICATES THE TYPE OF CONTACT/S/ INCLUDED ON THE ITEM. 3D MODE REPLY 31AP551AP562AG81 CTCRJ 04DIAMETER,NOMINAL,LINK PIN LINK PIN NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CTCSL 16STYLE,FACE,FIRST DISCHARGE FLANGE FIRST DISCHARGE FLANGE FACE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FLANGE FACE. 1L MODE REPLY 0 CTCTD 14SHAPE,END,DRIVE DRIVE END SHAPE THE PHYSICAL CONFIGURATION OF THE DRIVE END. SELECT REPLY CODE 10AP00 CTCWJ 04DIAMETER,CIRCLE,BOLT,ALIGNMENT HOLE ALIGNMENT HOLE BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTCXJ A18TYPE AND QUANTITY,HOLE,CIRCULAR PATTERN CIRCULAR PATTERN HOLE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF HOLES PROVIDED ON THE CIRCULAR PATTERN. 1D AND 1A MODE REPLY12AH37 CTCYD 11METHOD,FURNISHING,DATA DATA FURNISHING METHOD THE METHOD OR COMPONENT USED TO VISIBLY SHOW THE INFORMATION REQUIRED. SELECT REPLY CODE 10AP59 CTCZL 16STYLE,FACE,SECOND INTAKE FLANGE SECOND INTAKE FLANGE FACE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FLANGE FACE. 1L MODE REPLY 0 CTDBJ /D/ 04DIAMETER,HOLE,MOUNTING,ELEMENT ELEMENT MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTDCA 19STEPS ACCOMMODATED,PROGRAMMING PROGRAMMING STEPS ACCOMMODATED THE MAXIMUM NUMBER OF PROGRAMMING STEPS ACCOMMODATED. 1A MODE REPLY 0 CTDDB 13THREAD PITCH IN MILLIMETERS,HOLE HOLE THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE HOLE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CTDFJ /D/ 10CURRENT RATING IN AMPS,MAXIMUM,CONTACT CONTACT MAXIMUM CURRENT RATING IN AMPS THE MAXIMUM CURRENT WHICH THE CONTACT MAY CONTINUOUSLY CARRY WITHOUT DEGRADATION OR DESTRUCTION,EXPRESSED IN AMPERES. 2D AND 1B MODE REPLY21AP551AP56 CTDGD /D/ 08LOCATION,INSULATION INSULATION LOCATION INDICATES THE LOCATION OF THE INSULATION ON AN ITEM. SELECT REPLY CODE 10AN73 CTDHB 10PERCENTAGE,VOLUME,DISTILLATION LOSS,MAXIMUM MAXIMUM DISTILLATION LOSS VOLUME PERCENTAGE AN INDICATION OF THE MAXIMUM AMOUNT LOST BY DISTILLATION,EXPRESSED IN PERCENT. 1B MODE REPLY 0 CTDJD 18TYPE,ATTACHMENT,PIN PIN ATTACHMENT TYPE INDICATES THE TYPE OF DEVICE THAT IS ATTACHED TO THE PIN. SELECT REPLY CODE 10AJ74 CTDKL 16STYLE,FACE,SECOND DISCHARGE FLANGE SECOND DISCHARGE FLANGE FACE STYLE THE STYLE DESIGNATION INDICATION THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FLANGE FACE. 1L MODE REPLY 0 CTDLJ 10CURRENT RATING AT MAXIMUM RATED VOLTAGE,LOAD,MAIN CONTACT MAIN CONTACT LOAD CURRENT RATING AT MAXIMUM RATED VOLTAGE THE AMOUNT OF CURRENT THE MAIN CONTACTS ARE RATED TO MAKE OR BREAK AT MAXIMUM RATED VOLTAGE,WITH A SPECIFIED LOAD. 2D AND 1B MODE REPLY22AN862AN87 CTDMJ 04HEIGHT,OVERALL,STUD SHANK STUD SHANK OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CTDND 18TYPE,DEVICE,SWITCH ACTUATOR STOP SWITCH ACTUATOR STOP DEVICE TYPE INDICATES THE TYPE OF DEVICE INCLUDED IN THE SWITCH TO LIMIT THE ANGULAR ROTATION OF ITS ACTUATOR. SELECT REPLY CODE 10AD89 CTDPJ /D/ 04WIDTH OF BRUSH PART,BRUSH,SECOND SECOND BRUSH WIDTH OF BRUSH PART NONE. 2D AND 1B MODE REPLY21AA051AC20 CTDQJ 04DIAMETER,OUTSIDE,SECONDARY WASHER SECONDARY WASHER OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTDRJ 04DIAMETER,BRANCH,FIRST FIRST BRANCH DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTDSD 01COLOR,LIGHT,TRANSMITTED TRANSMITTED LIGHT COLOR THE HUE OR TINT OF THE TRANSMITTED LIGHT. SELECT REPLY CODE 10AD06 CTDTJ 04DIAMETER,SHANK,NUT END NUT END SHANK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTDWJ 10REACTANCE IN OHMS,ZSO-90,PLUS J PLUS J ZSO-90 REACTANCE IN OHMS THE REACTANCE (X) PART OF THE STATOR IMPEDANCE WITH THE ROTOR OPEN AND DISPLACED 90 DEGREES FROM ZERO (ZSO-90),EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 CTDXB 13THREAD PITCH IN MILLIMETERS,END,SECOND SECOND END THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CTDYD 13THREAD SERIES DESIGNATOR,INTAKE,FIRST FIRST INTAKE THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATION FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CTDZJ 10PERCENTAGE AT MAXIMUM TEMP,EVAPORATION EVAPORATION PERCENTAGE AT MAXIMUM TEMP AN INDICATION OF THE MAXIMUM TEMPERATURE AT WHICH A SPECIFIED EVAPORATION OF THE ITEM OCCURS,EXPRESSED IN PERCENT. 2D AND 1B MODE REPLY22AD213AJ40 CTFBD 17SURFACE TREATMENT,INCLOSURE INCLOSURE SURFACE TREATMENT THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE INCLOSURE IS PLATED,DIPPED,AND/OR COATED. THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF. SELECT REPLY CODE 10SF01 CTFCJ /D/ 04LENGTH,SLOT,STUD STUD SLOT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTFDJ 04LENGTH,WAVEGUIDE WAVEGUIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTFFD 13THREAD SERIES DESIGNATOR,DISCHARGE,FIRST FIRST DISCHARGE THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CTFGJ 04ANGLE,TIP,STEM STEM TIP ANGLE NONE. 1D AND 1B MODE REPLY11AP38 CTFHJ 04LENGTH,LEG,WAVEGUIDE WAVEGUIDE LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTFJD /D/ 13THREAD SERIES DESIGNATOR,COUNTERBORE COUNTERBORE THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATION FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC COUNTERBORE DIAMETER. SELECT REPLY CODE 10AH06 CTFKJ 04WIDTH,MAJOR,SECOND END KEYWAY SECOND END KEYWAY MAJOR WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTFLJ 04ANGLE,TILT,FORWARD,FORK FORK FORWARD TILT ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CTFMF T10DEVIATION IN PERCENT,TOLERANCE,MAXIMUM MAXIMUM TOLERANCE DEVIATION IN PERCENT THE MAXIMUM DEVIATION BETWEEN TOLERANCES OF THE INDIVIDUAL ELEMENTS OF THE ITEM,EXPRESSED IN PERCENT. 1F MODE REPLY 0 CTFND 13THREAD SERIES DESIGNATOR,INTAKE,SECOND SECOND INTAKE THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CTFPJ 04LENGTH,LEG,SECOND,WAVEGUIDE WAVEGUIDE SECOND LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTFQJ 04LENGTH,LEG,SIXTH,WAVEGUIDE WAVEGUIDE SIXTH LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTFRJ 04DEPTH,OVERALL,COUPLING COUPLING OVERALL DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTFSJ 04LENGTH,SEAL SEAL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTFTJ A19SOURCE AND DESIGNATOR,OUTLINE,CASE CASE OUTLINE SOURCE AND DESIGNATOR THE ALPHA-NUMERIC DESIGNATION,ASSIGNED BY THE CONTROLLING AGENCY,BY WHICH THE OUTLINE OF THE CASE IS IDENTIFIED. 1D AND 1A MODE REPLY12AF94 CTFWJ 04HEIGHT,OUTSIDE,SEAL SEAL OUTSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CTFXD /D/ 09MATERIAL,POINT,PEN PEN POINT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE PEN POINT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CTFYJ 04HEIGHT,OUTSIDE,VANE VANE OUTSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CTFZD 03DESIGNATION,TOLERANCE,STANDARD STANDARD TOLERANCE DESIGNATION THE STANDARD TOLERANCE DESIGNATION INDICATING THE MANUFACTURED LIMITATIONS OF THE ITEM AS ESTABLISHED BY THE VARIOUS SPECIFICATIONS AND STANDARDS. SELECT REPLY CODE 10AF01 CTGBD 13THREAD SERIES DESIGNATOR,DISCHARGE,SECOND SECOND DISCHARGE THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CTGCA 10CAPACITY RATING IN HEAT UNITS,HEAT,ANODE ANODE HEAT CAPACITY RATING IN HEAT UNITS THE HEAT CAPACITY,IN HEAT UNITS,FOR WHICH THE ANODE IS RATED. 1A MODE REPLY 0 CTGDJ /D/ 04SIZE ACCOMMODATED,CROSS-SECTION,WIRE WIRE CROSS-SECTION SIZE ACCOMMODATED THE CROSS-SECTION SIZE OF THE WIRE THE ITEM IS DESIGNED TO ACCOMMODATE. 2D AND 1B MODE REPLY21AA441AC20 CTGFD 18TYPE,GAS,FILLING FILLING GAS TYPE INDICATES THE TYPE OF GAS WITH WHICH THE ITEM IS FILLED. SELECT REPLY CODE 10AE50 CTGGJ 10IMPEDANCE RATING IN OHMS IMPEDANCE RATING IN OHMS THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) TO THE FLOW OF ALTERNATING CURRENT,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC00 CTGHG 19NAME,ITEM,APPROVED,PACKAGE,STOWAGE STOWAGE PACKAGE APPROVED ITEM NAME THE APPROVED ITEM NAME USED TO DESCRIBE THE PACKING MEANS IN WHICH THE ITEM IS TRANSPORTED OR STORED. IT CONSISTS OF A SINGLE OR COMPOUND NOUN OR A NOUN PHRASE AND MAY BE FOLLOWED BY MODIFIERS. FULL TEXT WRITE-IN 0 CTGJA /D/ 16STYLE,SHAPE,CROSS-SECTIONAL CROSS-SECTIONAL SHAPE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE CROSS-SECTIONAL SHAPE OF THE ITEM. 1A MODE REPLY 0 CTGKJ 13THREAD SIZE,NOMINAL,FIRST INTAKE FIRST INTAKE NOMINAL THREAD SIZE A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD. 1D AND 1B MODE REPLY11AA05 CTGLJ 04LENGTH,ACCOMMODATION,BODY MOUNTING HOLE,LONGEST LONGEST BODY MOUNTING HOLE ACCOMMODATION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTGMJ 04SIZE ACCOMMODATED,PIPE,NOMINAL,BRANCH BRANCH NOMINAL PIPE SIZE ACCOMMODATED NONE. 1D AND 1B MODE REPLY11AA05 CTGNF T10RANGE IN PICOFARADS,CAPACITANCE CAPACITANCE RANGE IN PICOFARADS THE MINIMUM AND MAXIMUM VALUES OF THE ELECTRICAL CAPACITANCE MEASURED BETWEEN TWO SPECIFIED POINTS ON THE ITEM,EXPRESSED IN PICOFARADS. 1F MODE REPLY 0 CTGPJ 10VOLTAGE RATING AND TYPE,NONDERATED NONDERATED VOLTAGE RATING AND TYPE THE HIGHEST POTENTIAL AND TYPE THAT MAY BE APPLIED TO THE ITEM,AT THE HIGHEST OPERATING TEMPERATURE PERMISSIBLE WITHOUT VOLTAGE DERATING. 2D AND 1B MODE REPLY21AB621AC81 CTGQJ T10CAPACITANCE CHANGE IN PERCENT AT OPERATING TEMP FROM 25 DEG CELSIUS CAPACITANCE CHANGE IN PERCENT AT OPERATING TEMP FROM 25 DEG CELSIUS THE LIMITS OF CAPACITANCE CHANGE IN PERCENT AT OPERATING TEMPERATURE FROM A STATED VALUE AT 25 DEGREES CELSIUS. 1D AND 1F MODE REPLY11AC20 CTGRJ A18TYPE AND QUANTITY,DRIVE,DEVICE,ADJUSTMENT ADJUSTMENT DEVICE DRIVE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF DRIVE(S) PROVIDED FOR THE ADJUSTMENT DEVICE. 1D AND 1A MODE REPLY13AE10 CTGSB 10CAPACITANCE DRIFT IN PICOFARADS CAPACITANCE DRIFT IN PICOFARADS THE DRIFT OF CAPACITANCE,EXPRESSED IN PICOFARADS. 1B MODE REPLY 0 CTGTB 10TEMP IN DEG CELSIUS,REFERENCE REFERENCE TEMP IN DEG CELSIUS THE TEMPERATURE AT WHICH NOMINAL ZERO POWER RESISTANCE IS SPECIFIED,EXPRESSED IN DEGREES CELSIUS. 1B MODE REPLY 0 CTGWB 10HUMIDITY PERCENTAGE,SPOT,DESICCANT DESICCANT SPOT HUMIDITY PERCENTAGE THE RELATIVE HUMIDITY PERCENTAGE LEVEL(S) AT WHICH A DESICCANT SPOT,OR A SERIES OF DESICCANT SPOTS,ON AN ITEM WILL CHANGE COLOR. 1B MODE REPLY 0 CTGXJ /D/ 04TAPER,SLOT,CROSS KEY CROSS KEY SLOT TAPER NONE. 2D AND 1B MODE REPLY21AB391AC20 CTHBJ 10STRENGTH,BREAKING BREAKING STRENGTH THE MEASURED LOAD REQUIRED TO BREAK THE ITEM IN TENSION. 2D AND 1B MODE REPLY22AG671AC20 CTHCJ 04ANGLE,TAPER,SECOND END SECOND END TAPER ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CTHDJ A11METHOD AND QUANTITY,ADJUSTMENT ADJUSTMENT METHOD AND QUANTITY THE MEANS PROVIDED AND NUMBER OF ADJUSTMENTS INCLUDED ON THE ITEM. 1D AND 1A MODE REPLY13AL41 CTHFJ 10CURRENT RATING,LOAD,CONTACT CONTACT LOAD CURRENT RATING THE AMOUNT OF CURRENT THAT THE CONTACTS ARE RATED TO MAKE OR BREAK WITH A SPECIFIED LOAD. 2D AND 1B MODE REPLY22AN861AD92 CTHGJ /D/A12QUANTITY PER UNIT OF MEASURE,LINE,HORIZONTAL HORIZONTAL LINE QUANTITY PER UNIT OF MEASURE THE NUMBER OF HORIZONTAL LINES PER SPECIFIC UNIT OF MEASURE. 1D AND 1A MODE REPLY11AB39 CTHHJ A19DOCUMENT AND CLASSIFICATION,MATERIAL,SHELL SHELL MATERIAL DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS CLASS,CONDITION,TEMPER,AND THE LIKE,THAT IDENTIFIES THE SHELL MATERIAL. 2D AND 1A MODE REPLY21AP331AP18 CTHJJ 04THICKNESS,FLANGE,FIRST INTAKE FIRST INTAKE FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTHKJ 04ANGLE,HEAD,SMALL END SMALL END HEAD ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CTHLJ 04ANGLE BETWEEN CENTERLINE OF HOLES ANGLE BETWEEN CENTERLINE OF HOLES NONE. 2D AND 1B MODE REPLY21AP381AC20 CTHMJ /D/ 10TIME IN NANOSECONDS,DELAY,PROPAGATION PROPAGATION DELAY TIME IN NANOSECONDS THE ELAPSED TIME INTERVAL REQUIRED FOR A CHANGE IN LOGIC LEVEL TO BE TRANSMITTED THROUGH AN ELEMENT OR A CHAIN OF ELEMENTS,EXPRESSED IN NANOSECONDS. 2D AND 1B MODE REPLY21AP451AC20 CTHNJ /D/ 10RESPONSE IN NANOMETER UNITS AT FIFTY PERCENT OF MAXIMUM LEVEL,SPECTRAL SPECTRAL RESPONSE IN NANOMETER UNITS AT FIFTY PERCENT OF MAXIMUM LEVEL THE VALUE(S) OF VISIBLE LIGHT UNIT(S) TO WHICH THE ITEM WILL RESPOND AT FIFTY PERCENT MAXIMUM RESPONSE LEVEL,EXPRESSED IN NANOMETER UNITS. 1D AND 1B MODE REPLY11AA05 CTHPJ /D/T10RANGE,ADJUSTMENT,CONTACT ACTUATING DIFFERENTIAL CONTACT ACTUATING DIFFERENTIAL ADJUSTMENT RANGE THE MINIMUM AND MAXIMUM LIMITS TO WHICH THE ACTUATING DIFFERENTIAL OF THE CONTACTS MAY BE ADJUSTED. 1D AND 1F MODE REPLY12AG20 CTHQJ 10PRELOAD RATING,BEARING BEARING PRELOAD RATING THE AMOUNT OF INTERNAL LOADING IN A BEARING WHICH IS INDEPENDENT OF ANY EXTERNAL RADIAL AND/OR AXIAL LOAD. 2D AND 1B MODE REPLY22AG671AC20 CTHRJ 04HEIGHT AND TYPE,OVERALL,NOMINAL,PACKAGE PACKAGE NOMINAL OVERALL HEIGHT AND TYPE THE NOMINAL DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP,AND THE TYPE OF PACKAGE. 2D AND 1B MODE REPLY21AA052AD28 CTHSJ /D/ 04DIAMETER,HOLE,FIRST PROJECTION FIRST PROJECTION HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTHTJ 04ANGLE,INCLUDED INCLUDED ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CTHWL 16STYLE,WASHER,PRIMARY PRIMARY WASHER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PRIMARY WASHER. 1L MODE REPLY 0 CTHXJ /D/ 04HEIGHT,OVERALL OVERALL HEIGHT PLEASE USE MRC ABKW IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 CTHYJ 04ANGLE,CONTACT CONTACT ANGLE THE SIZE OF THE ANGLE FORMED AT THE FORCE POINT OF CONTACT. 2D AND 1B MODE REPLY21AP381AC20 CTHZJ /D/ 10SENSITIVITY RATING SENSITIVITY RATING PLEASE USE MRC ANTG IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1B MODE REPLY13AK11 CTJBJ 04LENGTH,STEP,SHAFT SHAFT STEP LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTJCJ 10FLASH POINT AND TEST METHOD,MINIMUM MINIMUM FLASH POINT AND TEST METHOD A NUMERIC VALUE OF THE MINIMUM TEMPERATURE AT WHICH THE VAPOR WILL IGNITE,AND THE TEST METHOD. 2D AND 1B MODE REPLY21AB363AL43 CTJDA /D/ 12QUANTITY,ROW,DIMPLED PROJECTION DIMPLED PROJECTION ROW QUANTITY THE NUMBER OF ROWS OF DIMPLED PROJECTIONS ON THE ITEM. 1A MODE REPLY 0 CTJFJ 04LENGTH,SHANK,PUSH BUTTON PUSH BUTTON SHANK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTJGJ /D/ 10DELIVERY RATE,HEAT,COOLANT COOLANT HEAT DELIVERY RATE INDICATES THE RATE OF HEAT DELIVERY TO THE COOLANT OF THE ITEM. 1D AND 1B MODE REPLY11AP36 CTJHJ /D/ 10DELIVERY RATE,HEAT,DUCT DUCT HEAT DELIVERY RATE THE RATE OF HEAT DELIVERY TO THE DUCT OF THE ITEM. 1D AND 1B MODE REPLY11AP36 CTJJJ 04THICKNESS,MATERIAL,PRIMARY WASHER PRIMARY WASHER MATERIAL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTJKJ 04THICKNESS,PORTION,FLATTED,SHAFT SHAFT FLATTED PORTION THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTJLD 18TYPE,SCREEN,FLUOROSCOPIC FLUOROSCOPIC SCREEN TYPE INDICATES THE TYPE OF FLUOROSCOPIC SCREEN PROVIDED. SELECT REPLY CODE 10AG41 CTJMJ A18TYPE AND QUANTITY,ANTIROTATION/LUBRICATION ANTIROTATION/LUBRICATION TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF FEATURES USED FOR THE INTRODUCTION OF A LUBRICANT OR AN ANTIROTATIONAL DEVICE. 1D AND 1A MODE REPLY12AG25 CTJND 18TYPE,PLUG,AIR AIR PLUG TYPE INDICATES THE TYPE OF AIR PLUG. SELECT REPLY CODE 10AK12 CTJPB /D/ 10OUTPUT IN MILLIVOLTS,MAXIMUM,TOTAL NULL VOLTAGE TOTAL NULL VOLTAGE MAXIMUM OUTPUT IN MILLIVOLTS THE MAXIMUM FUNDAMENTAL NULL VOLTAGE PLUS HARMONICS,EXPRESSED IN MILLIVOLTS. 1B MODE REPLY 0 CTJQJ /D/ 10POWER RATING,OUTPUT,MOTOR,ELECTRIC ELECTRIC MOTOR OUTPUT POWER RATING THE AMOUNT OF OUTPUT POWER FOR WHICH THE ELECTRIC MOTOR IS RATED. 1D AND 1B MODE REPLY11AC33 CTJRJ 04THICKNESS,FLANGE,SECOND INTAKE SECOND INTAKE FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTJSJ 10WEIGHT,UNIT,UNPACKAGED UNPACKAGED UNIT WEIGHT THE MEASURED WEIGHT OF AN ITEM UNENCUMERED BY PACKAGING OR PACKING MATERIAL. 2D AND 1B MODE REPLY22AN751AC20 CTJTJ 04LENGTH AND TYPE,OVERALL,NOMINAL,PACKAGE PACKAGE NOMINAL OVERALL LENGTH AND TYPE THE NOMINAL DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS,AND THE TYPE OF PACKAGE. 2D AND 1B MODE REPLY21AA052AD28 CTJWJ /D/ 10STRENGTH,BREAKING,WARP DIRECTION WARP DIRECTION BREAKING STRENGTH THE GREATEST LONGITUDINAL STRESS AN ITEM CAN BEAR WITHOUT TEARING APART IN WARP DIRECTION PER UNIT OF MEASURE. 1D AND 1B MODE REPLY12AJ20 CTJXJ T10RATE PER HOUR,DOSE DOSE RATE PER HOUR THE MINIMUM AND MAXIMUM AMOUNT OF ABSORBED RADIATION DETECTED PER HOUR. 1D AND 1F MODE REPLY12AJ20 CTJYJ 04LENGTH,END,ATTACHMENT ATTACHMENT END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTJZJ 04LENGTH,OVERALL,STACK STACK OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS BETWEEN THE FIRST AND LAST PLATE WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE STACK(S). 2D AND 1B MODE REPLY21AA051AC20 CTKBJ /D/ 10VOLTAGE RATING IN VOLTS,AC,MAXIMUM,CONTACT CONTACT MAXIMUM AC VOLTAGE RATING IN VOLTS THE MAXIMUM ALTERNATING CURRENT POTENTIAL THAT MAY BE APPLIED CONTINUOUSLY TO THE CONTACT WITHOUT DAMAGE,EXPRESSED IN VOLTS. 3D AND 1B MODE REPLY31AP551AP562AN87 CTKCJ 04THICKNESS,FLANGE,FIRST DISCHARGE FIRST DISCHARGE FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTKDJ 04DEPTH,FLAP,ENVELOPE ENVELOPE FLAP DEPTH A MEASUREMENT OF AN ENVELOPE FLAP,IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CTKFJ 10TAPER TAPER THE AMOUNT OF TAPER OF THE ITEM. 2D AND 1B MODE REPLY21AB391AC20 CTKGJ 04WIDTH AND TYPE,OVERALL,NOMINAL,PACKAGE PACKAGE NOMINAL OVERALL WIDTH AND TYPE THE NOMINAL OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PACKAGE,IN DISTINCTION FROM THICKNESS,AND THE TYPE OF PACKAGE. 2D AND 1B MODE REPLY21AA052AD28 CTKHJ /D/ 10STRENGTH,TENSILE TENSILE STRENGTH THE GREATEST LONGITUDINAL STRESS AN ITEM CAN BEAR WITHOUT TEARING APART PER UNIT OF MEASURE. 1D AND 1B MODE REPLY12AJ20 CTKJA /D/ 10RATIO IN THOUSANDTHS,GOLD ALLOY GOLD ALLOY RATIO IN THOUSANDTHS THE RATIO OF PURE GOLD TO THE GOLD ALLOY WITH WHICH THE ITEM IS USED,EXPRESSED IN THOUSANDTHS. 1A MODE REPLY 0 CTKKJ 04DIAMETER,PLATE,CLINCH CLINCH PLATE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTKLJ A19DOCUMENT AND CLASSIFICATION,MATERIAL,INSERT INSERT MATERIAL DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS CLASS,CONDITION,TEMPER,AND THE LIKE,THAT IDENTIFIES THE INSERT MATERIAL. 2D AND 1A MODE REPLY21AP331AP18 CTKMH 11METHOD AND LOCATION,ACTUATION ACTUATION METHOD AND LOCATION THE MEANS BY WHICH THE ITEM IS ACTIVATED AND ITS LOCATION. 2D MODE REPLY 23AC583AN73 CTKND /D/ 18TYPE,RESERVOIR,INK INK RESERVOIR TYPE INDICATES THE TYPE OF INK RESERVOIR INCLUDED. SELECT REPLY CODE 10AP61 CTKPD 19FEATURE,DESIGN DESIGN FEATURE A FEATURE OF THE ITEM INDICATING WHETHER IT IS DESIGNED FOR OPTIONAL OR SPECIFIC MOUNTING OF EQUIPMENT. SELECT REPLY CODE 10AP53 CTKQJ 04ANGLE,SLOT SLOT ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CTKRJ /D/A12QUANTITY,HOOK HOOK QUANTITY THE NUMBER OF HOOKS PER UNIT OF MEASURE. 1D AND 1A MODE REPLY13AJ40 CTKSD /D/ 13THREAD SERIES DESIGNATOR,FACILITY,RIM FASTENING RIM FASTENING FACILITY THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER OF A RIM FASTENING FACILITY. SELECT REPLY CODE 10AH06 CTKTJ 04LENGTH,GROOVE,INNER INNER GROOVE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTKWJ 04RADIUS,SURFACE,LEFT,ELEMENT ELEMENT LEFT SURFACE RADIUS THE RADIUS OF THE LEFT SURFACE OF THE ELEMENT. 1D AND 1B MODE REPLY11AA05 CTKXJ 04RADIUS,SURFACE,RIGHT,ELEMENT ELEMENT RIGHT SURFACE RADIUS THE RADIUS OF THE RIGHT SURFACE OF THE ELEMENT. 1D AND 1B MODE REPLY11AA05 CTKYJ 04RADIUS,SURFACE,CONVEX CONVEX SURFACE RADIUS THE RADIUS OF THE CONVEX SURFACE OF THE ITEM. 1D AND 1B MODE REPLY11AA05 CTKZJ 04ANGLE ANGLE THE ANGLE BETWEEN DESIGNATED POINTS ON AN ITEM. 1D AND 1B MODE REPLY11AP38 CTLBJ /D/ 04WIDTH OF BRUSH PART,BRUSH,THIRD THIRD BRUSH WIDTH OF BRUSH PART NONE. 2D AND 1B MODE REPLY21AA051AC20 CTLCJ 04WIDTH,MINOR,SECOND END KEYWAY SECOND END KEYWAY MINOR WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTLDJ 10VOLTAGE RATING IN VOLTS AND CURRENT TYPE,STRIKING,GAS GAS STRIKING VOLTAGE RATING IN VOLTS AND CURRENT TYPE THE RATED VALUE OF THE VOLTAGE,EXPRESSED IN VOLTS,AND THE TYPE OF CURRENT WHICH WILL CAUSE THE GAS WITHIN THE ITEM TO IONIZE AND BECOME ELECTRICALLY CHARGED. 2D AND 1B MODE REPLY22AN871AC20 CTLFJ 04ANGLE,SPACING,HOLE HOLE SPACING ANGLE THE ANGLE FORMED BY THE CENTERLINE OF THE BEARING AND THE CENTERLINE OF TWO HOLES NOT IN THE SAME PLANE. 2D AND 1B MODE REPLY21AP381AC20 CTLGJ 13THREAD SIZE,NOMINAL,DISCHARGE,FIRST FIRST DISCHARGE NOMINAL THREAD SIZE A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD. 1D AND 1B MODE REPLY11AA05 CTLHJ 04TAPER,RING,OUTER OUTER RING TAPER NONE. 2D AND 1B MODE REPLY21AB391AC20 CTLJB 13THREAD PITCH IN MILLIMETERS,MOUNTING MOUNTING THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE MOUNTING THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CTLKJ 04ANGLE,SELF-ALIGNMENT SELF-ALIGNMENT ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CTLLJ 04ANGLE,INCLUDED,POINT SWIVEL POINT SWIVEL INCLUDED ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CTLMD 19FEATURE,LUBRICATION LUBRICATION FEATURE THE FEATURE INHERENT IN THE ITEM DESIGN TO EFFECT LUBRICATION. SELECT REPLY CODE 10AG25 CTLNJ 04ANGLE BETWEEN LUGS ANGLE BETWEEN LUGS NONE. 2D AND 1B MODE REPLY21AP381AC20 CTLPJ 04THICKNESS,FLANGE,SECOND DISCHARGE SECOND DISCHARGE FLANGE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTLQD 18TYPE,HOLE,GAGE GAGE HOLE TYPE INDICATES THE TYPE OF HOLE THE ITEM IS DESIGNED TO GAGE. SELECT REPLY CODE 10AH37 CTLRJ 10ECCENTRICITY ECCENTRICITY NONE. 2D AND 1B MODE REPLY21AA051AC20 CTLSJ 04ANGLE,BEAM WIDTH BEAM WIDTH ANGLE THE ANGLE BETWEEN TWO OPPOSITE HALF-POWER (THREE DECIBEL (3 DB)) POINTS OF THE BEAM. 2D AND 1B MODE REPLY21AP381AA99 CTLTJ 04DEPTH,RECESS,STUD STUD RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTLWJ /D/ 04SIZE,WIRE,PRIMARY WINDING PRIMARY WINDING WIRE SIZE DESIGNATES THE SIZE OF THE PRIMARY WINDING WIRE. 1D AND 1B MODE REPLY12AG67 CTLXJ /D/ 04SIZE,WIRE,SECONDARY WINDING SECONDARY WINDING WIRE SIZE DESIGNATES THE SIZE OF THE SECONDARY WINDING WIRE. 1D AND 1B MODE REPLY12AG67 CTLYJ 10STRENGTH AT 25 PCT DEFLECTION,COMPRESSION COMPRESSION STRENGTH AT 25 PCT DEFLECTION THE SQUEEZING LOAD AN ITEM CAN WITHSTAND WITHOUT BREAKING AT 25 PERCENT DEFLECTION. 2D AND 1B MODE REPLY22AG671AC20 CTLZJ /D/ 04LENGTH,BODY,BULB BULB BODY LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTMBJ A18TYPE AND LOCATION DESIGNATOR,GUIDE,SHELL SHELL GUIDE TYPE AND LOCATION DESIGNATOR INDICATES THE TYPE OF GUIDE INCLUDED ON THE SHELL AND ITS LOCATION. 1D AND 1A MODE REPLY12AP52 CTMCJ 13THREAD SIZE,NOMINAL,SECOND INTAKE SECOND INTAKE NOMINAL THREAD SIZE A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD. 1D AND 1B MODE REPLY11AA05 CTMDJ 04LENGTH,OVERALL,PUSH BUTTON SOCKET PUSH BUTTON SOCKET OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTMFJ 04LENGTH,ELEMENT,ROLLING ROLLING ELEMENT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTMGB 10KILOWATT RATING KILOWATT RATING AN INDICATION OF THE RATED KILOWATT OF THE ITEM. 1B MODE REPLY 0 CTMHB /D/ 10KILOWATT RATING,MOTOR,ELECTRIC ELECTRIC MOTOR KILOWATT RATING THE RATED KILOWATT OF THE ELECTRIC MOTOR. 1B MODE REPLY 0 CTMJB /D/ 10KILOWATT RATING,POWER SOURCE POWER SOURCE KILOWATT RATING THE RATED KILOWATT OF THE POWER SOURCE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1B MODE REPLY 0 CTMKB /D/ 10KILOWATT RATING,MOTOR,FAN FAN MOTOR KILOWATT RATING THE RATED KILOWATT OF THE FAN MOTOR. 1B MODE REPLY 0 CTMLJ 04DIAMETER,INSIDE,SECOND EYE SECOND EYE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTMMJ 04DIAMETER,BORE,WORKING WORKING BORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTMNB 10GAIN IN DECIBELS,POWER POWER GAIN IN DECIBELS THE RATIO OF THE SIGNAL INTENSITY OF AN ITEM RADIATED IN A SPECIFIC DIRECTION TO THE SIGNAL INTENSITY RADIATED IN THE SAME DIRECTION BY A STANDARD DEVICE,EXPRESSED IN DECIBELS. 1B MODE REPLY 0 CTMPJ 04LENGTH,FLANGE,FIRST INTAKE FIRST INTAKE FLANGE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTMQJ A08LOCATION AND QUANTITY,GROOVE,SURFACE SURFACE GROOVE LOCATION AND QUANTITY INDICATES THE LOCATION AND NUMBER OF GROOVES ON THE SURFACE OF THE ITEM. 1D AND 1A MODE REPLY13AJ91 CTMRJ 04DISTANCE BETWEEN RETAINING RINGS DISTANCE BETWEEN RETAINING RINGS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTMSJ 10TAPER,END,FORWARD FORWARD END TAPER THE AMOUNT OF TAPER OF THE FORWARD END OF THE ITEM. 2D AND 1B MODE REPLY21AB391AC20 CTMTB /D/ 13THREAD PITCH IN MILLIMETERS,STEM STEM THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CTMWL 16STYLE DESIGNATOR,TIP,CLEANING CLEANING TIP STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CLEANING TIP. 1L MODE REPLY 0 CTMXD /D/ 19FINENESS,PARTICLE,EUROPEAN PHARMACOPEIA EUROPEAN PHARMACOPEIA PARTICLE FINENESS THE FINENESS OF THE PARTICLES AS RELATED TO THE SIEVE SIZE NUMBER DEFINED IN THE EUROPEAN PHARMACOPEIA. SELECT REPLY CODE 10AP07 CTMYD 18TYPE,CONTAINER,DRAINAGE DRAINAGE CONTAINER TYPE INDICATES THE TYPE OF DRAINAGE CONTAINER. SELECT REPLY CODE 10AF72 CTMZD 09MATERIAL,SEMICONDUCTOR SEMICONDUCTOR MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE SEMICONDUCTOR IS FABRICATED. SELECT REPLY CODE 10MA01 CTNBJ 10RATING AND LOCATION,RESISTOR RESISTOR RATING AND LOCATION THE VALUE AND LOCATION OF THE RESISTOR REQUIRED TO CONTROL THE CURRENT. 2D AND 1B MODE REPLY22AN863AN73 CTNCJ /D/ 04DIAMETER,MINOR,TAPERED BRUSH PART,SECOND BRUSH SECOND BRUSH TAPERED BRUSH PART MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTNDJ 04LENGTH,FLANGE,FIRST DISCHARGE FIRST DISCHARGE FLANGE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTNFJ /D/ 04DISTANCE BETWEEN KNURLS DISTANCE BETWEEN KNURLS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTNGJ 04DIMENSION,KEYWAY KEYWAY DIMENSION THE MEASURED DISTANCES WHICH ARE CHARACTERISTIC OF THE KEYWAY. 2D AND 1B MODE REPLY21AA051AC20 CTNHB /D/ 13THREAD PITCH IN MILLIMETERS,END,THIRD THIRD END THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREADED AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CTNJD 08LOCATION,MATERIAL,ENVIRONMENTAL PROTECTION ENVIRONMENTAL PROTECTION MATERIAL LOCATION INDICATES THE LOCATION(S) AT WHICH THE ENVIRONMENTAL PROTECTION MATERIAL IS JOINED TO THE ELECTROMAGNETIC INTERFERENCE/RADIO FREQUENCY INTERFERENCE (EMI/RFI) MATERIAL. SELECT REPLY CODE 10AJ91 CTNKL 16STYLE,TIP,LEFT LEFT TIP STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LEFT TIP. 1L MODE REPLY 0 CTNLD 19RELATIONSHIP WITH LEFT TIP,RIGHT TIP RIGHT TIP RELATIONSHIP WITH LEFT TIP AN INDICATION OF WHETHER OR NOT THE RIGHT TIP IS IDENTICAL TO THE LEFT TIP. SELECT REPLY CODE 10AN69 CTNMJ 04DEPTH,HOLE MINIMUM,PLUG,AIR AIR PLUG MINIMUM HOLE DEPTH A MEASUREMENT OF THE MINIMUM HOLE DEPTH THE AIR PLUG IS DESIGNED TO GAGE,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 CTNNJ 04ANGLE,INNER FACE TO OUTER FACE,RIGHT BOTTOM RIGHT BOTTOM INNER FACE TO OUTER FACE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CTNPJ 04DIAMETER ACCOMMODATED,SHAFT,STANDARD STANDARD SHAFT DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE STANDARD SHAFT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CTNQJ /D/ 10TEMP RATING,SOLIDIFICATION POINT SOLIDIFICATION POINT TEMP RATING THE TEMPERATURE AT WHICH THE ITEM WILL BECOME SOLID OR HARD. 1D AND 1B MODE REPLY13AJ40 CTNRB /D/ 13THREAD PITCH IN MILLIMETERS,END,FOURTH FOURTH END THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREADED AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CTNSJ 04LENGTH,FLANGE,SECOND INTAKE SECOND INTAKE FLANGE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTNTJ 10TEMP RATING,MINIMUM,FLASH POINT FLASH POINT MINIMUM TEMP RATING THE LOWEST TEMPERATURE AT WHICH THE ITEM WILL IGNITE AND BURN. 1D AND 1B MODE REPLY13AJ40 CTNWJ 10TEMP RATING,MINIMUM,POUR POINT POUR POINT MINIMUM TEMP RATING THE LOWEST TEMPERATURE AT WHICH THE ITEM WILL POUR. 1D AND 1B MODE REPLY13AJ40 CTNXJ /D/A13THREAD TOLERANCE CLASS,END,THIRD THIRD END THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE. 1D AND 1A MODE REPLY13AN73 CTNYJ 10POWER RATING,BRAKE BRAKE POWER RATING THE BRAKE POWER DELIVERED BY THE ITEM FOR A SPECIFIC APPLICATION AT A SPECIFIC SPEED. 1D AND 1B MODE REPLY11AC33 CTNZJ /D/ 04DIAMETER,END,LARGE,TAPER PIN TAPER PIN LARGE END DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGE END OF THE TAPER PIN,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CTPBA 10POWER RATING SPECIFIED RPM,BRAKE BRAKE POWER RATING SPECIFIED RPM THE SPECIFIED REVOLUTIONS PER MINUTE AT WHICH THE BRAKE POWER RATING IS DETERMINED. 1A MODE REPLY 0 CTPCJ 04DISTANCE,BEND,OFFSET OFFSET BEND DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CTPDJ /D/ 04DIAMETER,UNIT,PACKAGED PACKAGED UNIT DIAMETER THE LENGTH OF A STRAIGHT LINE PASSING THROUGH THE CENTER OF A CIRCULAR ITEM ENCUMBERED BY PACKAGING OR PACKING,AND TERMINATING AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CTPFJ /D/A13THREAD TOLERANCE CLASS,END,FOURTH FOURTH END THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE. 1D AND 1A MODE REPLY13AN73 CTPGJ /D/ 10POWER RATING,BRAKE,COMMON OUTPUT SHAFT COMMON OUTPUT SHAFT BRAKE POWER RATING THE BRAKE POWER DELIVERED BY THE COMMON OUTPUT SHAFT FOR A SPECIFIC APPLICATION AT A SPECIFIC SPEED. 1D AND 1B MODE REPLY11AC33 CTPHJ A10RATE PER SECOND,FRAME FRAME RATE PER SECOND THE NUMBER OF FRAMES PER SECOND FOR WHICH THE ITEM IS RATED. 1D AND 1A MODE REPLY12AL36 CTPJD 11METHOD,ATTACHMENT ATTACHMENT METHOD THE MEANS BY WHICH THE ITEM IS ATTACHED. SELECT REPLY CODE 10AP50 CTPKB /D/ 13THREAD PITCH IN MILLIMETERS,INLET INLET THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREADED AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CTPLJ /D/T13THREAD PITCH DIAMETERS,NONSTANDARD,COUNTERBORE COUNTERBORE NONSTANDARD THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A COUNTERBORE NONSTANDARD STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 CTPMJ /D/A13THREAD TOLERANCE CLASS,INLET INLET THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE. 1D AND 1A MODE REPLY13AN73 CTPNJ 19NUMBER,MODULE MODULE NUMBER A NUMERIC VALUE THAT REPRESENTS THE PITCH DIAMETER FOR EACH TOOTH OF AN ITEM IN RELATION TO DIAMETRICAL AND CIRCULAR PITCHES. 1D AND 1B MODE REPLY11AA05 CTPPB 19NUMBER,OCTANE,AVIATION LEAN MIXTURE AVIATION LEAN MIXTURE OCTANE NUMBER AN INDICATION OF THE AVIATION LEAN MIXTURE OCTANE NUMBER. 1B MODE REPLY 0 CTPQB /D/ 13THREAD PITCH IN MILLIMETERS,BULKHEAD BULKHEAD THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREADED AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CTPRA /D/ 10POWER RATING SPECIFIED RPM,BRAKE,COMMON OUTPUT SHAFT COMMON OUTPUT SHAFT BRAKE POWER RATING SPECIFIED RPM THE SPECIFIED REVOLUTIONS PER MINUTE AT WHICH THE COMMON OUTPUT SHAFT BRAKE POWER RATING IS DETERMINED. 1A MODE REPLY 0 CTPSD 18TYPE,REPLACEMENT,METER METER REPLACEMENT TYPE INDICATES THE TYPE OF METER IN WHICH THE REPLACEMENT METER WILL BE USED. SELECT REPLY CODE 10AK13 CTPTA 10ACCURACY RATING ACCURACY RATING THE DEVIATION FROM A STANDARD OR TRUE VALUE FOR WHICH THE ITEM IS RATED. 1A MODE REPLY 0 CTPWJ 04ANGLE,COUNTERSINK,HEAD HEAD COUNTERSINK ANGLE THE INCLUDED ANGLE OF THE HEAD COUNTERSINK. 2D AND 1B MODE REPLY21AP381AC20 CTPXJ /D/ 10POWER RATING,SHAFT SHAFT POWER RATING THE SHAFT POWER DELIVERED BY THE ITEM FOR A SPECIFIC APPLICATION AT A SPECIFIC SPEED. 1D AND 1B MODE REPLY11AC33 CTPYL 16STYLE,TIP,RIGHT RIGHT TIP STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE RIGHT TIP. 1L MODE REPLY 0 CTPZJ 04THICKNESS,RING,PACKING PACKING RING THICKNESS A MEASUREMENT OF THE SMALLEST INSIDE DIMENSION OF THE PACKING RING. 2D AND 1B MODE REPLY21AA051AC20 CTQBA /D/ 10POWER RATING SPECIFIED RPM,SHAFT SHAFT POWER RATING SPECIFIED RPM THE SPECIFIED REVOLUTIONS PER MINUTE AT WHICH THE SHAFT POWER RATING IS DETERMINED. 1A MODE REPLY 0 CTQCL 16STYLE,ELEMENT,SEALING SEALING ELEMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SEALING ELEMENT. 1L MODE REPLY 0 CTQDJ 10AREA,HOLDING,OPEN POSITION OPEN POSITION HOLDING AREA A MEASUREMENT OF THE HOLDING AREA WHEN THE ITEM IS IN AN OPEN POSITION. 2D AND 1B MODE REPLY22AG671AC20 CTQFJ 13THREAD SIZE,NOMINAL,SECOND DISCHARGE SECOND DISCHARGE NOMINAL THREAD SIZE A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD. 1D AND 1B MODE REPLY11AA05 CTQGJ /D/ 10POWER RATING,AIR AIR POWER RATING THE RATED AIR POWER PRODUCED BY THE ITEM. 1D AND 1B MODE REPLY11AC33 CTQHD 01COLOR,DISPLAY DISPLAY COLOR THE HUE OR TINT OF THE DISPLAY. SELECT REPLY CODE 10AD06 CTQJJ 04LENGTH,OVERALL,FASTENER FASTENER OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTQKJ /D/ 10POWER RATING,AHEAD AHEAD POWER RATING THE POWER OF THE ITEM IN AHEAD (FORWARD) MOTION FOR A SPECIFIC APPLICATION AT A SPECIFIC SPEED. 1D AND 1B MODE REPLY11AC33 CTQLD 11METHOD,SUSPENSION,MOVEMENT MOVEMENT SUSPENSION METHOD THE MEANS EMPLOYED TO SUSPEND THE MOVEMENT OF THE ITEM. SELECT REPLY CODE 10AH72 CTQMJ 10CURRENT RATING FOR WHICH DESIGNED CURRENT RATING FOR WHICH DESIGNED THE AMOUNT OF CURRENT FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY22AN861AC20 CTQNJ 10VOLTAGE RATING IN VOLTS PER CHARACTERISTIC VOLTAGE RATING IN VOLTS PER CHARACTERISTIC THE VALUE OF THE VOLTAGE THAT MAY BE APPLIED,EXPRESSED IN VOLTS,AND THE SYMBOL USED TO IDENTIFY THE SPECIFIC ELECTRICAL CHARACTERISTIC. 2D AND 1B MODE REPLY21AC202AH15 CTQPA /D/ 10POWER RATING SPECIFIED RPM,AHEAD AHEAD POWER RATING SPECIFIED RPM THE SPECIFIED REVOLUTIONS PER MINUTE AT WHICH THE AHEAD (FORWARD) POWER RATING IS DETERMINED. 1A MODE REPLY 0 CTQQJ 04DISTANCE ALONG LENGTH,CENTER TO CENTER,ATTACHMENT FEATURE ATTACHMENT FEATURE CENTER TO CENTER DISTANCE ALONG LENGTH THE CENTER TO CENTER DISTANCE BETWEEN AN ATTACHMENT FEATURE AND THE ADJACENT ATTACHMENT FEATURE ALONG THE LENGTH. 2D AND 1B MODE REPLY21AA051AC20 CTQRJ 04DISTANCE ALONG WIDTH,CENTER TO CENTER,ATTACHMENT FEATURE ATTACHMENT FEATURE CENTER TO CENTER DISTANCE ALONG WIDTH THE CENTER TO CENTER DISTANCE BETWEEN AN ATTACHMENT FEATURE AND THE ADJACENT ATTACHMENT FEATURE ALONG THE WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CTQSF T10VOLTAGE TOLERANCE IN PERCENT VOLTAGE TOLERANCE IN PERCENT THE PERMISSIBLE VARIATION IN THE VOLTAGE VALUE OF AN ITEM FROM ITS RATED VALUE,EXPRESSED IN PERCENT. 1F MODE REPLY 0 CTQTD 19MEDIUM,OPERATING OPERATING MEDIUM THE ENVIRONMENT IN WHICH THE ITEM WILL FUNCTION. SELECT REPLY CODE 10AN91 CTQWJ 10PRESSURE RATING,MAXIMUM MAXIMUM PRESSURE RATING THE MAXIMUM PRESSURE AT WHICH AN ITEM IS RATED TO OPERATE. 1D AND 1B MODE REPLY12AG67 CTQXJ 10CURRENT RATING PER CHARACTERISTIC CURRENT RATING PER CHARACTERISTIC THE LEVEL OF ELECTRICAL FLOW AND THE SYMBOL USED TO IDENTIFY THE SPECIFIC ELECTRICAL CHARACTERISTIC. 3D AND 1B MODE REPLY32AB491AC202AH16 CTQYJ A18TYPE AND QUANTITY,HOLE,MOUNTING MOUNTING HOLE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF MOUNTING HOLES PROVIDED ON THE ITEM. 1D AND 1A MODE REPLY12AH37 CTQZJ /D/ 19UNDERSIZE,SHAFT SHAFT UNDERSIZE THE MEASUREMENT OF THE SHAFT UNDERSIZE THE ITEM IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 CTRBD /D/ 13THREAD DIRECTION,COUNTERBORE COUNTERBORE THREAD DIRECTION THE DIRECTION OF THE COUNTERBORE THREAD WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AA38 CTRCJ 10AREA,SURFACE,HEAT TRANSFER,EFFECTIVE EFFECTIVE HEAT TRANSFER SURFACE AREA A MEASUREMENT OF THE SURFACE OF THE ITEM THAT EFFECTS THE TRANSFER OF HEAT. 1D AND 1B MODE REPLY11AC51 CTRDJ 10POWER RATING PER CHARACTERISTIC POWER RATING PER CHARACTERISTIC THE AMOUNT OF ELECTRICAL POWER THAT CAN BE DISSIPATED AND THE SPECIFIC ELECTRICAL CHARACTERISTIC. 3D AND 1B MODE REPLY32AB491AC202AH63 CTRFJ 04TAPER,SHANK SHANK TAPER NONE. 2D AND 1B MODE REPLY22AG201AC20 CTRGJ 10CAPACITANCE RATING IN PICOFARADS CAPACITANCE RATING IN PICOFARADS THE RELATIVE LEVEL OF THE QUANTITY OF ELECTRICAL CHARGE AT A GIVEN POTENTIAL WHICH THE ITEM IS RECEIVING AND STORING,EXPRESSED IN PICOFARADS. 1D AND 1B MODE REPLY11AC20 CTRHJ 04DISTANCE ALONG WIDTH,SMALLEST,OUTSIDE EDGE TO INSIDE EDGE OUTSIDE EDGE TO INSIDE EDGE SMALLEST DISTANCE ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTRJD 11METHOD,HOLDING HOLDING METHOD THE MEANS UTILIZED TO HOLD AN ITEM. SELECT REPLY CODE 10AF39 CTRKJ 10TRANSFER RATIO TRANSFER RATIO THE RATIO OF THE INPUT ELECTRICAL SIGNAL TO THE OUTPUT ELECTRICAL SIGNAL AT SPECIFIED OPERATING CONDITIONS. 2D AND 1B MODE REPLY21AC202AP67 CTRLJ 10LEAD,TETRAETHYL,ALLOWABLE,MAXIMUM MAXIMUM ALLOWABLE TETRAETHYL LEAD A MEASUREMENT OF THE MAXIMUM TETRAETHYL LEAD ALLOWABLE IN THE ITEM. 1D AND 1B MODE REPLY12AG67 CTRMD 19CONDITION,SURFACE,LENS BACK LENS BACK SURFACE CONDITION INDICATES THE SURFACE CONDITION OF THE LENS BACK. SELECT REPLY CODE 10AN72 CTRNJ 04DISTANCE FROM SHOULDER END TO WRENCH OPENING CENTER DISTANCE FROM SHOULDER END TO WRENCH OPENING CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTRPJ 04LENGTH BEFORE WELDING,OVERALL OVERALL LENGTH BEFORE WELDING THE DIMENSION MEASURED,BEFORE WELDING,ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CTRQJ 04DISTANCE FROM LUG END TO END OF BEARING DISTANCE FROM LUG END TO END OF BEARING NONE. 2D AND 1B MODE REPLY21AA051AC20 CTRRJ 04ANGLE,OFFSET,DRIVE END DRIVE END OFFSET ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CTRSF /D/T10RANGE IN MILLIMETERS,PITCH PITCH RANGE IN MILLIMETERS THE MINIMUM AND MAXIMUM PITCHES IN MILLIMETERS THE ITEM IS CAPABLE OF MEASURING. 1F MODE REPLY 0 CTRTD 09MATERIAL,TOP,SHELF SHELF TOP MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE SHELF TOP IS FABRICATED. SELECT REPLY CODE 10MA01 CTRWJ /D/ 04LENGTH,FLANGE,SECOND DISCHARGE SECOND DISCHARGE FLANGE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTRXH 01COLOR TONE PRODUCED PER SOURCE COLOR TONE PRODUCED PER SOURCE THE HUE,TINT OR SHADING PRODUCED BY THE ITEM. 2D MODE REPLY 26AD062AM43 CTRYJ /D/ 10POWER RATING,ASTERN ASTERN POWER RATING THE POWER OF THE ITEM IN ASTERN (REVERSE) MOTION FOR A SPECIFIC APPLICATION AT A SPECIFIC SPEED. 1D AND 1B MODE REPLY11AC33 CTRZJ 04WIDTH,FLANGE,FIRST INTAKE FIRST INTAKE FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTSBJ 10LUMINOUS INTENSITY LUMINOUS INTENSITY THE MEASUREMENT OF LUMINOUS FLUX IN A GIVEN DIRECTION PER UNIT OF SOLID ANGLE. 2D AND 1B MODE REPLY23AK091AC20 CTSCJ 04DISTANCE ALONG LENGTH,SMALLEST,OUTSIDE EDGE TO INSIDE EDGE OUTSIDE EDGE TO INSIDE EDGE SMALLEST DISTANCE ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTSDJ 04DEPTH,SLOT SLOT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTSFD /D/ 19FEATURE,STORAGE,PROTECTIVE PROTECTIVE STORAGE FEATURE INDICATES THE STORAGE FEATURE/S/ REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS. SELECT REPLY CODE 10AD43 CTSGJ 10OPERATING TEMP PER MEASUREMENT POINT,MAXIMUM MAXIMUM OPERATING TEMP PER MEASUREMENT POINT THE MAXIMUM TEMPERATURE AT WHICH THE ITEM IS DESIGNED TO OPERATE AT EACH MEASUREMENT POINT. 2D AND 1B MODE REPLY21AB363AJ91 CTSHA /D/ 10POWER RATING SPECIFIED RPM,ASTERN ASTERN POWER RATING SPECIFIED RPM THE SPECIFIED REVOLUTIONS PER MINUTE AT WHICH THE ASTERN (REVERSE) POWER RATING IS DETERMINED. 1A MODE REPLY 0 CTSJL /D/ 16STYLE,BRUSH,THIRD THIRD BRUSH STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE THIRD BRUSH. 1L MODE REPLY 0 CTSKJ 04DISTANCE FROM LUG END TO INSIDE OF FLANGE DISTANCE FROM LUG END TO INSIDE OF FLANGE NONE. 2D AND 1B MODE REPLY21AA051AC20 CTSLJ 04WIDTH,FLANGE,FIRST DISCHARGE FIRST DISCHARGE FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTSNJ 04DIAMETER,BODY,END,LEFT LEFT END BODY DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTSPJ 10TEMP,MINIMUM,ANILINE POINT ANILINE POINT MINIMUM TEMP THE LOWEST TEMPERATURE AT WHICH AN ITEM IS MISCIBLE WITH ANILINE. 1D AND 1B MODE REPLY13AJ40 CTSQJ 10MILLIGRAMS OF CHEMICAL REQUIRED MILLIGRAMS OF CHEMICAL REQUIRED THE MILLIGRAMS OF CHEMICAL REQUIRED PER UNIT OF MEASURE. 1D AND 1B MODE REPLY13AJ40 CTSRJ /D/ 10YIELD,AGENT,DECONTAMINATING DECONTAMINATING AGENT YIELD THE AMOUNT OF DECONTAMINATING AGENT YIELDED PER UNIT OF MEASURE. 1D AND 1B MODE REPLY13AK09 CTSSJ 04DIAMETER FROM HEAD,SEVENTH SEVENTH DIAMETER FROM HEAD NONE. 2D AND 1B MODE REPLY21AA051AC20 CTSTJ 04RADIUS,CORNER,INSIDE INSIDE CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTSWJ /D/ 04RADIUS,CORNER,OUTSIDE OUTSIDE CORNER RADIUS PLEASE USE MRC ADPW IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 CTSXJ /D/ 04THICKNESS,WASHER,ACCOMMODATED ACCOMMODATED WASHER THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTSYJ /D/ 04DIAMETER,INSIDE,WASHER,ACCOMMODATED ACCOMMODATED WASHER INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTSZJ 04DIAMETER,OUTSIDE,WASHER,ACCOMMODATED ACCOMMODATED WASHER OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTTBJ /D/ 04RADIUS,FILLET,TIP,FIRST FIRST TIP FILLET RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTTCJ A13THREAD TOLERANCE CLASS THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE. 1D AND 1A MODE REPLY13AN73 CTTDJ A11METHOD AND QUANTITY,ATTACHMENT,CIRCUIT CIRCUIT ATTACHMENT METHOD AND QUANTITY THE MEANS PROVIDED FOR ELECTRICAL CONNECTION TO A CIRCUIT AND THE NUMBER OF EACH TYPE OF CONNECTION. 1D AND 1A MODE REPLY13AN89 CTTFJ 04RADIUS,OUTER,SECOND END SECOND END OUTER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTTGJ 04DIAMETER,BODY,END,RIGHT RIGHT END BODY DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTTHJ 04WIDTH ACROSS CORNERS,INSIDE INSIDE WIDTH ACROSS CORNERS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTTJJ 10VOLTAGE RATING IN VOLTS AND CURRENT TYPE,FORWARD FORWARD VOLTAGE RATING IN VOLTS AND CURRENT TYPE THE RATED VALUE OF THE FORWARD VOLTAGE,EXPRESSED IN VOLTS,AND THE CURRENT TYPE AT WHICH THE ITEM IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY12AN87 CTTKJ 04ANGLE,CUT,END END CUT ANGLE NONE. 1D AND 1B MODE REPLY11AP38 CTTLH /D/ 18TYPE AND LOCATION,JACKSCREW JACKSCREW TYPE AND LOCATION INDICATES THE TYPE OF POLARIZING JACKSCREW INCLUDED ON THE ITEM,AND ITS LOCATION. 2D MODE REPLY 21AB603AN73 CTTMJ /D/A10CLASSIFICATION AND TEST METHOD,RATING,HEAT HEAT RATING CLASSIFICATION AND TEST METHOD THE NUMERIC CLASSIFICATION OF THE THERMAL VALUE ASSIGNED TO THE ITEM AND THE TEST METHOD. 1D AND 1A MODE REPLY13AJ50 CTTNJ /D/ 10IMPEDANCE IN OHMS,CHARACTERISTIC,RADIO FREQUENCY TYPE CONTACT RADIO FREQUENCY TYPE CONTACT CHARACTERISTIC IMPEDANCE IN OHMS THE IMPEDANCE FOR WHICH THE ITEM IS DESIGNED FOR MAXIMUM POWER TRANSFER,EXPRESSED IN OHMS. 2D AND 1B MODE REPLY21AP551AP56 CTTPJ /D/ 04DIAMETER,TIP,LEFT LEFT TIP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTTQJ /D/ 04DIAMETER,TIP,RIGHT RIGHT TIP DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTTRJ 04HEIGHT,TIP,LEFT LEFT TIP HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CTTSJ 04HEIGHT,TIP,RIGHT RIGHT TIP HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CTTTJ /D/ 04DIAMETER,INSIDE,TIP,LEFT LEFT TIP INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTTWJ /D/ 04DIAMETER,INSIDE,TIP,RIGHT RIGHT TIP INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTTXJ 04RADIUS,TIP,LEFT LEFT TIP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTTYJ 04RADIUS,TIP,RIGHT RIGHT TIP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTTZD 01COLOR,COVERING,PROTECTIVE,CABLE/CORD CABLE/CORD PROTECTIVE COVERING COLOR THE HUE OR TINT OF THE CABLE/CORD PROTECTIVE COVERING. SELECT REPLY CODE 10AD06 CTWBA 03DESIGNATOR,SIZE,PREHEAT ORIFICE PREHEAT ORIFICE SIZE DESIGNATOR A DESIGNATION THAT IS USED TO INDICATE THE DRILL SIZE NUMBER OF THE PREHEAT ORIFICE. 1A MODE REPLY 0 CTWCJ 04ANGLE,EXTRUSION EXTRUSION ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CTWDJ 04ANGLE,PROTUBERANCE PROTUBERANCE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CTWFJ 04DISTANCE FROM THREADED END TO SHANK HOLE CENTER DISTANCE FROM THREADED END TO SHANK HOLE CENTER THE DISTANCE FROM THE SHANK HOLE CENTERLINE TO THE THREADED END. 2D AND 1B MODE REPLY21AA051AC20 CTWGJ 04WIDTH,FLANGE,SECOND INTAKE SECOND INTAKE FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTWHJ 04ANGLE,V GROOVE V GROOVE ANGLE THE ANGLE OF THE V GROOVE. 2D AND 1B MODE REPLY21AP381AC20 CTWJL 16STYLE,HEAD,CLOSURE CLOSURE HEAD STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CLOSURE HEAD. 1L MODE REPLY 0 CTWKJ 04WIDTH,TIP,SECOND SECOND TIP WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTWLJ 04RADIUS,FILLET,TIP,SECOND SECOND TIP FILLET RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTWMJ 04DISTANCE FROM MOUNTING HOLE CENTER TO BASE EDGE,SECOND SECOND DISTANCE FROM MOUNTING HOLE CENTER TO BASE EDGE NONE. 2D AND 1B MODE REPLY21AA051AC20 CTWNJ 10VOLTAGE RATING IN VOLTS,OPERATING OPERATING VOLTAGE RATING IN VOLTS THE VALUE(S) OF ROOT MEAN SQUARE OR DIRECT CURRENT POTENTIAL WHICH MUST BE APPLIED TO THE ITEM FOR OPERATION,EXPRESSED IN VOLTS. 2D AND 1B MODE REPLY21AB621AC20 CTWPJ /D/ 04RADIUS,INNER,TIP,LEFT LEFT TIP INNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTWQJ /D/ 04RADIUS,INNER,TIP,RIGHT RIGHT TIP INNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTWRJ 04WIDTH,TIP,LEFT LEFT TIP WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTWSJ 04WIDTH,TIP,RIGHT RIGHT TIP WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTWTJ /D/ 04RADIUS,FILLET,TIP,LEFT LEFT TIP FILLET RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTWWJ /D/ 04RADIUS,FILLET,TIP,RIGHT RIGHT TIP FILLET RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTWXJ 04RADIUS,OUTER,TIP,LEFT LEFT TIP OUTER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTWYJ /D/ 04RADIUS,OUTER,TIP,RIGHT RIGHT TIP OUTER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTWZD 19COMPATIBILITY,INTERFACE INTERFACE COMPATIBILITY THE TYPE AND/OR STANDARD INTERFACE SYSTEM WITH WHICH THE ITEM IS COMPATIBLE. SELECT REPLY CODE 10AK95 CTXBJ A18TYPE AND QUANTITY,CONTACT,ACCOMMODATED ACCOMMODATED CONTACT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF CONTACTS ACCOMMODATED BY THE ITEM. 1D AND 1A MODE REPLY12AG81 CTXCB 13THREAD PITCH IN MILLIMETERS,END,PISTON ROD,FIRST FIRST PISTON ROD END THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREADED AXIS OF THE FIRST PISTON ROD END,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CTXDB /D/ 13THREAD PITCH IN MILLIMETERS,END,PISTON ROD,SECOND SECOND PISTON ROD END THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREADED AXIS OF THE SECOND PISTON ROD END,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CTXFB 13THREAD PITCH IN MILLIMETERS,MOUNTING FACILITY MOUNTING FACILITY THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREADED AXIS OF THE MOUNTING FACILITY,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CTXGB 13THREAD PITCH IN MILLIMETERS,PORT PORT THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREADED AXIS OF THE PORT THREAD,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CTXHB 13THREAD PITCH IN MILLIMETERS,SWITCH,STOPLIGHT STOPLIGHT SWITCH THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREADED AXIS OF THE STOPLIGHT SWITCH,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CTXJD 19CONDITION,SURFACE,LENS LENS SURFACE CONDITION THE CONDITION OF THE LENS WITH RESPECT TO THE TEXTURE OF THE SURFACE. SELECT REPLY CODE 10AN72 CTXKJ 10LOAD RATING,OPERATING,SAFE SAFE OPERATING LOAD RATING THE SAFE OPERATING LOAD FOR WHICH THE ITEM IS DESIGNED TO ACCOMMODATE. 2D AND 1B MODE REPLY22AG671AC20 CTXLJ /D/A13THREAD TOLERANCE CLASS,BULKHEAD BULKHEAD THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE OF A BULKHEAD. 1D AND 1A MODE REPLY13AN73 CTXMJ /D/ 04SIZE ACCOMMODATED,CONDUCTOR CONDUCTOR SIZE ACCOMMODATED THE SIZE OF THE CONDUCTOR THE ITEM IS DESIGNED TO ACCOMMODATE. 2D AND 1B MODE REPLY21AA441AC20 CTXNJ 04DIAMETER,NOMINAL,PIN PIN NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PIN,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CTXPJ /D/ 04DISTANCE,SHOULDER TO HEAD END SHOULDER TO HEAD END DISTANCE PLEASE USE MRC CRQD IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 CTXRJ /D/ 04DEPTH,GROOVE,RELIEF RELIEF GROOVE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTXSA 12QUANTITY ACCOMMODATED,CONDUCTOR CONDUCTOR QUANTITY ACCOMMODATED THE NUMBER OF CONDUCTOR(S) ACCOMMODATED WITH THE ITEM. 1A MODE REPLY 0 CTXTJ 04DISTANCE,DETENT TO TAPERED END DETENT TO TAPERED END DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CTXWJ /D/ 04SIZE AND LOCATION,CONDUCTOR,STRANDED STRANDED CONDUCTOR SIZE AND LOCATION THE DESIGNATION USED TO DESCRIBE THE STRANDED CONDUCTOR SIZE AND ITS LOCATION. 2D AND 1B MODE REPLY21AA443AJ91 CTXXD 19CONSTRUCTION,CORE CORE CONSTRUCTION THE STRUCTURAL CHARACTERISTIC OF THE CORE. SELECT REPLY CODE 10AF37 CTXYD 19FORM,PREFABRICATION PREFABRICATION FORM THE PREFABRICATION FORM OF THE ITEM. SELECT REPLY CODE 10AC41 CTXZJ A12QUANTITY PER UNIT OF MEASURE QUANTITY PER UNIT OF MEASURE THE NUMBER OF ITEMS PER UNIT OF MEASURE. 1D AND 1A MODE REPLY13AJ40 CTYBD 11METHOD,CONDITIONING,END END CONDITIONING METHOD THE MEANS USED TO PREVENT UNRAVELING OF THE END(S) OF THE ITEM. SELECT REPLY CODE 10AA62 CTYCH 19ADJUSTABILITY,CONTACT CONTACT ADJUSTABILITY THE ADJUSTABILITY OF THE CONTACT. 2D MODE REPLY 22AG211AC06 CTYDJ 04LENGTH,ROD ROD LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTYFJ 13THREAD DIAMETER,NOMINAL,NONMACHINE NONMACHINE NOMINAL THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE NONMACHINE THREADED PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CTYGJ 10TEMP,DENSITY DENSITY TEMP THE TEMPERATURE AT WHICH THE DENSITY IS DETERMINED. 1D AND 1B MODE REPLY11AB36 CTYHJ /D/ 04WIDTH,GROOVE,RELIEF RELIEF GROOVE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTYJD 17SURFACE TREATMENT,BUCKLE BUCKLE SURFACE TREATMENT THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE BUCKLE SURFACE(S) AND CANNOT BE WIPED OFF. SELECT REPLY CODE 10SF01 CTYKJ 04ANGLE BETWEEN ADJACENT MOUNTING FACILITIES ANGLE BETWEEN ADJACENT MOUNTING FACILITIES A MEASUREMENT OF THE ANGLE BETWEEN ADJACENT MOUNTING FACILITIES. 2D AND 1B MODE REPLY21AP381AC20 CTYLJ /D/ 04SIZE AND LOCATION,CONDUCTOR,ROUND SOLID ROUND SOLID CONDUCTOR SIZE AND LOCATION THE DESIGNATION USED TO DESCRIBE THE ROUND SOLID CONDUCTOR SIZE AND ITS LOCATION. 2D AND 1B MODE REPLY21AA443AJ91 CTYMJ T10RANGE,ADJUSTMENT,CONTACT CONTACT ADJUSTMENT RANGE THE MINIMUM AND MAXIMUM LIMITS TO WHICH THE CONTACT(S) MAY BE ADJUSTED. 2D AND 1F MODE REPLY22AG212AG20 CTYNJ 04DIAMETER,CIRCLE,INSCRIBED INSCRIBED CIRCLE DIAMETER THE DIAMETER OF THE LARGEST CIRCLE THAT CAN BE DRAWN WITHIN THE CONFIGURATION. 1D AND 1B MODE REPLY11AA05 CTYPD /D/ 03DESIGNATION,LOAD,TIRE TIRE LOAD DESIGNATION DESIGNATES THE LOAD LIMITS OF A TIRE. SELECT REPLY CODE 10AE89 CTYQJ 04WIDTH ACROSS FLATS,STEP,FIRST FIRST STEP WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTYRJ /D/ 04WIDTH,FLANGE,SECOND DISCHARGE SECOND DISCHARGE FLANGE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CTYSH 18TYPE,ADJUSTMENT,CONTACT CONTACT ADJUSTMENT TYPE INDICATES THE TYPE OF DEVICE PROVIDED FOR MANUAL ADJUSTMENT OF THE CONTACT(S). 2D MODE REPLY 22AG212AG18 CTYTD 19CHARACTERISTIC,CODE,COMPOUND COMPOUND CODE CHARACTERISTIC THE CHARACTERISTIC OF THE ITEM THAT IS THE RESULT OF COMPOUNDING OF SPECIAL INGREDIENTS AS INDICATED BY THE MEDALLION BACKGROUND COLOR CODE. SELECT REPLY CODE 10AP69 CTYWJ 10MEASUREMENT AND TYPE,ANGULAR ANGULAR MEASUREMENT AND TYPE THE ANGULAR DIMENSION AND THE TYPE OF ANGLE. 2D AND 1B MODE REPLY21AP382AL23 CTYXJ 10STIMULUS RATING,CONTACT CONTACT STIMULUS RATING THE RATING OF THE STIMULUS REQUIRED TO ACTUATE AND/OR DEACTUATE THE CONTACT(S). 3D AND 1B MODE REPLY32AG211AC202AG20 CTYYJ 04RADIUS,POINT POINT RADIUS A MEASUREMENT OF THE DISTANCE FROM THE CENTER OF THE POINT TO THE CURVE. 1D AND 1B MODE REPLY11AA05 CTYZJ /D/ 04DIAMETER,MINOR,TAPERED BRUSH PART,THIRD BRUSH THIRD BRUSH TAPERED BRUSH PART MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTZBJ 10VOLTAGE RATING IN VOLTS,CONTACT CONTACT VOLTAGE RATING IN VOLTS THE VOLTAGE FOR WHICH THE CONTACT(S) IS RATED AT SEA LEVEL OR AT A SPECIFIED ALTITUDE,EXPRESSED IN VOLTS. 2D AND 1B MODE REPLY21AB621AD86 CTZCJ 10DISSIPATION RATING IN WATTS,POWER,OVEN HEATING ELEMENT OVEN HEATING ELEMENT POWER DISSIPATION RATING IN WATTS THE AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY THE OVEN HEATING ELEMENT(S),EXPRESSED IN WATTS. 1D AND 1B MODE REPLY11AC20 CTZDA /D/ 13THREAD TOLERANCE CLASS,CONNECTION,EXTERNAL EXTERNAL CONNECTION THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE. 1A MODE REPLY 0 CTZFA 19MARKING,INDICATOR,READOUT READOUT INDICATOR MARKING AN INDICATION OF THE MARKING ON THE READOUT INDICATOR. 1A MODE REPLY 0 CTZGJ A10STRENGTH,BREAKING,SHEAR SHEAR BREAKING STRENGTH THE LOAD APPLIED PERPENDICULARLY TO THE LONGITUDINAL AXIS OF AN ITEM AT WHICH POINT THE ITEM WILL FRACTURE WHEN SUBJECTED TO THE STANDARD SINGLE OR DOUBLE SHEAR TEST METHOD. 3D AND 1A MODE REPLY31AF091AC201AN71 CTZHB /D/ 13THREAD PITCH IN MILLIMETERS,PANEL BUSHING PANEL BUSHING THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CTZJD /D/ 13THREAD DIRECTION,HOLE,CONCENTRIC CONCENTRIC HOLE THREAD DIRECTION THE DIRECTION OF THE CONCENTRIC HOLE THREAD WHEN VIEWED AXIALLY. SELECT REPLY CODE 10AA38 CTZKJ 04DISTANCE BETWEEN UPPER CONNECTIONS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN UPPER CONNECTIONS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTZLD 18TYPE,CONNECTOR,PRESSURE PRESSURE CONNECTOR TYPE INDICATES THE TYPE OF PRESSURE CONNECTOR. SELECT REPLY CODE 10AJ57 CTZMJ 04DISTANCE BETWEEN LOWER CONNECTIONS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN LOWER CONNECTIONS NONE. 2D AND 1B MODE REPLY21AA051AC20 CTZNJ 10DISSIPATION RATING IN WATTS,POWER,SURFACE HEATING UNIT SURFACE HEATING UNIT POWER DISSIPATION RATING IN WATTS THE AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY THE SURFACE HEATING ELEMENT(S),EXPRESSED IN WATTS. 1D AND 1B MODE REPLY11AC20 CTZPJ 04DIAMETER,MATERIAL,END,ATTACHMENT ATTACHMENT END MATERIAL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTZQJ /D/ 10DISSIPATION RATING IN WATTS,POWER,HEATING ELEMENT,WARMING OVEN WARMING OVEN HEATING ELEMENT POWER DISSIPATION RATING IN WATTS THE AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY THE WARMING OVEN HEATING ELEMENT,EXPRESSED IN WATTS. 1D AND 1B MODE REPLY11AC20 CTZRJ 04DISTANCE FROM BAIL CENTER TO HOLE CENTER DISTANCE FROM BAIL CENTER TO HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 CTZSA /D/ 13THREAD QUANTITY PER INCH,PANEL BUSHING PANEL BUSHING THREAD QUANTITY PER INCH THE NUMBER OF PANEL BUSHING THREADS PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CTZTD 19TRUTH TABLE,CONTACT ARRANGEMENT CONTACT ARRANGEMENT TRUTH TABLE AN INDICATION OF THE CONFIGURATION OF THE CODED CONTACT SWITCHING STRUCTURE. SELECT REPLY CODE 10AP70 CTZWA /D/ 13THREAD TOLERANCE CLASS,CONNECTION,INTERNAL INTERNAL CONNECTION THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE. 1A MODE REPLY 0 CTZXJ /D/ 10DISSIPATION RATING IN WATTS,POWER,HEATING ELEMENT,BROILER BROILER HEATING ELEMENT POWER DISSIPATION RATING IN WATTS THE AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY THE BROILER HEATING ELEMENT(S),EXPRESSED IN WATTS. 1D AND 1B MODE REPLY11AC20 CTZYD 19FLASH RATING FLASH RATING THE RATED FLASH AS DETERMINED BY HOW RAPIDLY THE ITEM REACHES ITS PEAK LIGHT INTENSITY. SELECT REPLY CODE 10AE57 CTZZJ X19IDENTIFICATION,SPECIAL TRUTH TABLE SPECIAL TRUTH TABLE IDENTIFICATION THE CONTROLLING ACTIVITY AND IDENTIFICATION OF THE SPECIAL CODED CONTACT SWITCHING STRUCTURE. 1D AND 1A MODE REPLY15AN63 CUPMB 10CUTTING SPEED IN FEET PER MINUTE CUTTING SPEED IN FEET PER MINUTE THE SPEED OF THE CUTTER EXPRESSED IN FEET PER MINUTE. 1B MODE REPLY 0 CUTFJ 10FORCE,CUTTING CUTTING FORCE THE AMOUNT OF FORCE REQUIRED TO CUT. 2D AND 1B MODE REPLY22AB161AC20 CUTPJ 04OPENING,CUTTING CUTTING OPENING A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CUTTING OPENING. 2D AND 1B MODE REPLY21AA051AC20 CWABJ 10VOLTAGE RATING IN VOLTS,MAXIMUM,MAIN CONTACT MAIN CONTACT MAXIMUM VOLTAGE RATING IN VOLTS THE HIGHEST VOLTAGE AT WHICH THE MAIN CONTACTS ARE RATED FOR NORMAL OPERATION,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY12AN87 CWACJ 04LENGTH,TAPER,SHAFT SHAFT TAPER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWADD 18TYPE ACCOMMODATED,LAMP LAMP TYPE ACCOMMODATED THE FORM,CONSTRUCTION,OR TYPE OF LAMP WHICH DISTINGUISHES IT FROM OTHER LIKE ITEMS THAT THE ITEM WILL ACCOMMODATE. SELECT REPLY CODE 10AD48 CWAFJ 04DIAMETER FROM HEAD,SIXTH SIXTH DIAMETER FROM HEAD NONE. 2D AND 1B MODE REPLY21AA051AC20 CWAGJ 04LENGTH OF BRUSH PART,SINGLE BRUSH SINGLE BRUSH LENGTH OF BRUSH PART NONE. 2D AND 1B MODE REPLY21AA051AC20 CWAHJ 04DISTANCE,SPREAD,FORK FORK SPREAD DISTANCE THE OUTSIDE TO OUTSIDE DISTANCE BETWEEN FORKS. 2D AND 1B MODE REPLY21AA051AC20 CWAJA /D/ 03DESIGNATOR,LOCATION,INTER CONTACT INTER CONTACT LOCATION DESIGNATOR DESIGNATIONS WHICH ARE USED TO INDICATE THE POSITION BETWEEN TWO ADJACENT FIXED CONTACTS AND THE OPPOSITE TWO FIXED CONTACT POSITIONS OF A POLARIZING KEY. 1A MODE REPLY 0 CWAKB 19NUMBER,OCTANE,AVIATION RICH MIXTURE AVIATION RICH MIXTURE OCTANE NUMBER AN INDICATION OF THE AVIATION RICH MIXTURE OCTANE NUMBER. 1B MODE REPLY 0 CWALJ A14SHAPE AND QUANTITY,ORIFICE,PREHEAT PREHEAT ORIFICE SHAPE AND QUANTITY THE PHYSICAL CONFIGURATION AND NUMBER OF PREHEAT ORIFICES INCLUDED ON THE ITEM. 1D AND 1A MODE REPLY13AD07 CWAMA 10RATIO,GEAR GEAR RATIO INDICATES THE RATIO OF THE OUTPUT GEAR TO THE INPUT GEAR. 1A MODE REPLY 0 CWANJ /D/ 04DIAMETER,MINOR,TAPERED END,STUD STUD TAPERED END MINOR DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWAPJ /D/ 10VALUE,DENSITY DENSITY VALUE QUOTIENT OF THE PRODUCT MASS BY ITS VOLUME AT A SPECIFIED TEMPERATURE. 1D AND 1B MODE REPLY12AB49 CWAQJ 04DIAMETER,BRANCH,SECOND SECOND BRANCH DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWARA 13THREAD QUANTITY PER INCH,INTAKE,FIRST FIRST INTAKE THREAD QUANTITY PER INCH THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CWASJ 04LENGTH,SHANK,SECOND SECOND SHANK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWATJ 04ANGLE,INNER FACE TO OUTER FACE,LEFT BOTTOM LEFT BOTTOM INNER FACE TO OUTER FACE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CWAWJ 04DISTANCE,HOLE,REDUCER,UNTHREADED UNTHREADED REDUCER HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED REDUCER HOLE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CWAXJ 10CAPACITY,DESICCANT,MINIMUM MINIMUM DESICCANT CAPACITY THE MINIMUM AMOUNT OF HUMIDITY INDICATING AGENT THE ITEM IS DESIGNED TO HOLD. 1D AND 1B MODE REPLY12AN75 CWAYD 19CLASSIFICATION,SUPPLY SUPPLY CLASSIFICATION A CLASSIFICATION USED TO IDENTIFY THE SUPPLY FORM BY WHICH THE ITEM IS DELIVERED. SELECT REPLY CODE 10AM69 CWAZH /D/ 18TYPE,TERMINAL TERMINAL TYPE INDICATES THE TYPE OF TERMINAL FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. 3D MODE REPLY 31AP551AP563AN89 CWBBA 13THREAD QUANTITY PER INCH,DISCHARGE,FIRST FIRST DISCHARGE THREAD QUANTITY PER INCH THE NUMBER OF THREADS OF THE ITEM,PER LINEAR INCH,MEASURED ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CWBCB /D/ 10OUTPUT IN MILLIVOLTS,MAXIMUM,FUNDAMENTAL NULL VOLTAGE FUNDAMENTAL NULL VOLTAGE MAXIMUM OUTPUT IN MILLIVOLTS THE MAXIMUM FUNDAMENTAL COMPONENT OF THE NULL VOLTAGE,EXPRESSED IN MILLIVOLTS. 1B MODE REPLY 0 CWBDA /D/ 12QUANTITY,HOLDER,DRAWING POINT SECTION DRAWING POINT SECTION HOLDER QUANTITY THE NUMBER OF DRAWING POINT SECTION HOLDERS INCLUDED IN THE ITEM. 1A MODE REPLY 0 CWBFD 19LIFE,AVERAGE,RATED RATED AVERAGE LIFE A TERM DENOTING THE MEASUREMENT USED TO INDICATE THE AVERAGE LIFE OF THE ITEM. SELECT REPLY CODE 10AE52 CWBGJ 04DISTANCE,OFFSET,WAVEGUIDE WAVEGUIDE OFFSET DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CWBHJ 13THREAD SIZE,NOMINAL,SHAFT SHAFT NOMINAL THREAD SIZE THE LENGTH OF A STRAIGHT LINE PASSING THROUGH THE CENTER OF THE SHAFT THREADED PORTION,WITH TERMINATED POINTS AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWBJL 16STYLE,COLLAR COLLAR STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE COLLAR. 1L MODE REPLY 0 CWBKJ 04TAPER,END,FIRST FIRST END TAPER NONE. 1D AND 1B MODE REPLY11AB39 CWBLJ 04ANGLE,SECTOR SECTOR ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CWBMJ A13THREAD TOLERANCE CLASS,END,FIRST FIRST END THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE. 1D AND 1A MODE REPLY13AN73 CWBNJ 04LENGTH,LEG,LONGER,WAVEGUIDE WAVEGUIDE LONGER LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWBPJ 04LENGTH,LEG,THIRD,WAVEGUIDE WAVEGUIDE THIRD LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWBQJ 04HEIGHT,OVERALL,ADAPTER ADAPTER OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CWBRJ 04LENGTH OF BRUSH PART,FIRST BRUSH FIRST BRUSH LENGTH OF BRUSH PART NONE. 2D AND 1B MODE REPLY21AA051AC20 CWBSJ 04DIAMETER,INSIDE,SEAL SEAL INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWBTA 13THREAD QUANTITY PER INCH,INTAKE,SECOND SECOND INTAKE THREAD QUANTITY PER INCH THE NUMBER OF THREADS ON THE ITEM,PER LINEAR INCH,MEASURED ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CWBWJ 04THICKNESS,MATERIAL,SECONDARY WASHER SECONDARY WASHER MATERIAL THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CWBXJ 04WIDTH,INSIDE,SEAL SEAL INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWBYJ /D/ 04DIAMETER,OUTSIDE,VANE VANE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWBZJ 04RADIUS,NOMINAL,SEAT SEAT NOMINAL RADIUS THE NOMINAL RADIUS OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS. 1D AND 1B MODE REPLY11AA05 CWCBJ 04DIAMETER,CIRCLE,BOLT,SECURING HOLE SECURING HOLE BOLT CIRCLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWCCJ 04ANGLE,TILT,BACKWARD,FORK FORK BACKWARD TILT ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CWCDJ 04DIAMETER,OUTSIDE,NOMINAL NOMINAL OUTSIDE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWCFJ 04DISTANCE,FACE TO FACE FACE TO FACE DISTANCE THE FACE TO FACE DISTANCE. 1D AND 1B MODE REPLY11AA05 CWCGJ /D/ 13THREAD SIZE,NOMINAL,CORE TIP CORE TIP NOMINAL THREAD SIZE A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE NOMINAL THREAD SIZE. 1D AND 1B MODE REPLY11AA05 CWCHJ /D/ 04HEIGHT,OVERALL,HEAD HEAD OVERALL HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CWCJJ 04ANGLE,INSIDE INSIDE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CWCKJ 04THICKNESS,NOMINAL NOMINAL THICKNESS A NOMINAL MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 CWCLJ 04DISTANCE,FACE TO CENTERLINE,FIRST CONNECTION FIRST CONNECTION FACE TO CENTERLINE DISTANCE NONE. 1D AND 1B MODE REPLY11AA05 CWCMB /D/ 13THREAD PITCH IN MILLIMETERS,CORE TIP CORE TIP THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CWCNJ 04WIDTH ACROSS FLATS,NOMINAL NOMINAL WIDTH ACROSS FLATS THE SHORTEST NOMINAL STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT OF AN ITEM. 1D AND 1B MODE REPLY11AA05 CWCPA 13THREAD QUANTITY PER INCH,DISCHARGE,SECOND SECOND DISCHARGE THREAD QUANTITY PER INCH THE NUMBER OF THREADS ON THE ITEM,PER LINEAR INCH,MEASURED ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CWCQJ 04DIAMETER,NOMINAL,HOLE,BOLT BOLT HOLE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWCRJ 04DISTANCE,FACE TO CENTERLINE,SECOND CONNECTION SECOND CONNECTION FACE TO CENTERLINE DISTANCE NONE. 1D AND 1B MODE REPLY11AA05 CWCSJ 04LENGTH OF SHAFT FROM HOUSING LENGTH OF SHAFT FROM HOUSING A MEASUREMENT OF THE LONGEST DIMENSION OF THE SHAFT PROJECTION OF AN ITEM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CWCTJ 04DIAMETER,NOMINAL,CIRCLE,BOLT BOLT CIRCLE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWCWJ 04DISTANCE,FACE TO CENTERLINE,THIRD CONNECTION THIRD CONNECTION FACE TO CENTERLINE DISTANCE NONE. 1D AND 1B MODE REPLY11AA05 CWCXJ /D/ 04LENGTH,PORTION,SHANK SHANK PORTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWCYJ 04DISTANCE BETWEEN BOLT HOLES ALONG LENGTH,NOMINAL,CENTER TO CENTER CENTER TO CENTER NOMINAL DISTANCE BETWEEN BOLT HOLES ALONG LENGTH THE CENTER TO CENTER NOMINAL DISTANCE BETWEEN BOLT HOLES ALONG THE LENGTH OF AN ITEM. 1D AND 1B MODE REPLY11AA05 CWCZJ 04DISTANCE,FACE TO CENTERLINE,FOURTH CONNECTION FOURTH CONNECTION FACE TO CENTERLINE DISTANCE NONE. 1D AND 1B MODE REPLY11AA05 CWDBB 10AMOUNT OF EXISTENT GUM,MAXIMUM MAXIMUM AMOUNT OF EXISTENT GUM THE MASS,IN MILLIGRAMS,OF THE RESIDUE OBTAINED BY EVAPORATION OF 100 MILLILITERS OF THE PRODUCT. 1B MODE REPLY 0 CWDCJ 04DISTANCE BETWEEN BOLT HOLES ALONG WIDTH,NOMINAL,CENTER TO CENTER CENTER TO CENTER NOMINAL DISTANCE BETWEEN BOLT HOLES ALONG WIDTH THE CENTER TO CENTER NOMINAL DISTANCE BETWEEN BOLT HOLES ALONG THE WIDTH OF AN ITEM. 1D AND 1B MODE REPLY11AA05 CWDDJ 04DISTANCE,CENTER TO CENTER CENTER TO CENTER DISTANCE NONE. 1D AND 1B MODE REPLY11AA05 CWDFD 02DESIGN,FACE,FLANGE FLANGE FACE DESIGN THE DESIGN OF THE FLANGE FACE. SELECT REPLY CODE 10AH33 CWDGJ /D/A13THREAD TOLERANCE CLASS,CORE TIP CORE TIP THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE. 1D AND 1A MODE REPLY13AN73 CWDHJ 04HEIGHT,NOMINAL,FACE,RAISED RAISED FACE NOMINAL HEIGHT A NOMINAL MEASUREMENT FROM THE BOTTOM TO THE TOP SURFACE OF A RAISED FACE,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 CWDJB 13THREAD PITCH IN MILLIMETERS,INTAKE,FIRST FIRST INTAKE THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CWDKJ 04ANGLE,CHAMFER,POINT POINT CHAMFER ANGLE NONE. REPLACED BY MRC CSYT WITH ISAC 0368. 2D AND 1B MODE REPLY21AP381AC20 CWDLJ 04DIAMETER,NOMINAL,FACE,RAISED RAISED FACE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A RAISED FACE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWDMJ 04DISTANCE,SHAFT CENTER TO MOUNTING SURFACE SHAFT CENTER TO MOUNTING SURFACE DISTANCE THE DISTANCE BETWEEN THE CENTER OF THE SHAFT TO THE MOUNTING SURFACE. 1D AND 1B MODE REPLY11AA05 CWDNJ /D/ 04ANGLE,TIP,BLADE BLADE TIP ANGLE THE ANGLE OF THE TIP IN RELATION TO THE LONGITUDINAL AXIS OF THE BLADE. 2D AND 1B MODE REPLY21AP381AC20 CWDPJ 04DIAMETER,NOMINAL,RECESS RECESS NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE RECESS,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWDQA /D/ 13THREAD QUANTITY PER INCH,CORE TIP CORE TIP THREAD QUANTITY PER INCH THE NUMBER OF CORE TIP THREADS PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CWDRJ /D/ 04DISTANCE FROM CENTERLINE OF LIFTING SCREW HOLE TO NEAREST END OF KEY DISTANCE FROM CENTERLINE OF LIFTING SCREW HOLE TO NEAREST END OF KEY NONE. 2D AND 1B MODE REPLY21AA051AC20 CWDSJ 04DEPTH,NOMINAL,RECESS RECESS NOMINAL DEPTH A NOMINAL MEASUREMENT BETWEEN SPECIFIED POINTS ON THE RECESS,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 CWDTJ 04DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO LENGTH,CENTER TO CENTER,NOMINAL NOMINAL CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO LENGTH THE NOMINAL CENTER TO CENTER DISTANCE BETWEEN THE MOUNTING FACILITIES PARALLEL TO THE LENGTH. 1D AND 1B MODE REPLY11AA05 CWDWJ 04DIAMETER HOSE ACCOMMODATED,INSIDE,NOMINAL NOMINAL INSIDE DIAMETER HOSE ACCOMMODATED THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWDXJ /D/ 04DISTANCE BETWEEN LIFTING SCREW HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN LIFTING SCREW HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 CWDYJ 10TEMP RATING TEMP RATING THE TEMPERATURE AT WHICH THE ITEM IS DESIGNED TO OPERATE. 2D AND 1B MODE REPLY22AH001AB36 CWDZJ 04DIAMETER HOSE ACCOMMODATED,OUTSIDE,NOMINAL NOMINAL OUTSIDE DIAMETER HOSE ACCOMMODATED THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWFBJ 04ANGLE BETWEEN HOLES ANGLE BETWEEN HOLES NONE. 2D AND 1B MODE REPLY21AP381AC20 CWFCJ 04LENGTH AFTER WELDING,OVERALL OVERALL LENGTH AFTER WELDING THE DIMENSION MEASURED,AFTER WELDING,ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CWFDJ 04DIAMETER TUBE ACCOMMODATED,OUTSIDE,NOMINAL NOMINAL OUTSIDE DIAMETER TUBE ACCOMMODATED THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWFFJ 04LENGTH OF BRUSH PART,SECOND BRUSH SECOND BRUSH LENGTH OF BRUSH PART NONE. 2D AND 1B MODE REPLY21AA051AC20 CWFGD 03DESIGNATION FOR WHICH DESIGNED,THICKNESS,PIPE WALL PIPE WALL THICKNESS DESIGNATION FOR WHICH DESIGNED THE TERM USED TO DEFINE THE WALL THICKNESS CROSS-SECTIONAL DIMENSION OF PIPE OF VARIOUS MATERIAL AS PRESENTED BY A SCHEDULE,THICKNESS CLASS,CLASS STRENGTH,OR WEIGHT DESIGNATION. SELECT REPLY CODE 10AA35 CWFHD 18TYPE,DESIGN,CASE CASE DESIGN TYPE INDICATES THE TYPE OF DESIGN WHICH DESCRIBES THE CASE. SELECT REPLY CODE 10AP20 CWFJJ 04ANGLE BETWEEN HOLES,END,FIRST FIRST END ANGLE BETWEEN HOLES NONE. 2D AND 1B MODE REPLY21AF981AC20 CWFKJ 04THICKNESS FOR WHICH DESIGNED,NOMINAL,WALL,TUBING TUBING WALL NOMINAL THICKNESS FOR WHICH DESIGNED THE NOMINAL THICKNESS OF THE TUBING WALL FOR WHICH DESIGNED AS TAKEN FROM THE INSIDE SURFACE TO THE NEAREST OUTER SURFACE. 1D AND 1B MODE REPLY11AA05 CWFLJ 04DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF EIGHTH DIAMETER DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF EIGHTH DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWFMJ 04LENGTH,PORTION,FLATTED,SHAFT SHAFT FLATTED PORTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWFNJ 04DIAMETER,INSIDE,NOMINAL,REDUCED PASSAGE REDUCED PASSAGE NOMINAL INSIDE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE REDUCED PASSAGE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWFPJ 04DEPTH,BORE,FIRST END FIRST END BORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWFQJ 04DIAMETER,CIRCLE,MOUNTING FACILITY MOUNTING FACILITY CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING FACILITY CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWFRJ 04LENGTH,OVERALL,NOMINAL NOMINAL OVERALL LENGTH THE NOMINAL DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM. 1D AND 1B MODE REPLY11AA05 CWFSJ 04DEPTH,BORE,SECOND END SECOND END BORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWFTJ 04HEIGHT,FACE,RAISED,FIRST INTAKE FLANGE FIRST INTAKE FLANGE RAISED FACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CWFWJ 04DISTANCE,NOMINAL,CENTER TO CENTER,BEND BEND CENTER TO CENTER NOMINAL DISTANCE THE NOMINAL DISTANCE FROM THE CENTERLINE OF THE OPENING AT ONE END TO THE CENTERLINE OF THE OPENING AT THE OPPOSITE END. 1D AND 1B MODE REPLY11AA05 CWFXJ 10SPEED RATING IN RPM,ROTOR ROTOR SPEED RATING IN RPM THE SPEED RATING OF A ROTOR,EXPRESSED IN REVOLUTIONS PER MINUTE. 2D AND 1B MODE REPLY23AN283AN29 CWFYJ 04DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO WIDTH,CENTER TO CENTER,NOMINAL NOMINAL CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO WIDTH THE NOMINAL CENTER TO CENTER DISTANCE BETWEEN THE MOUNTING FACILITIES PARALLEL TO THE WIDTH. 1D AND 1B MODE REPLY11AA05 CWFZJ /D/ 04DIAMETER FOR WHICH DESIGNED,OUTSIDE,NOMINAL,TUBE TUBE NOMINAL OUTSIDE DIAMETER FOR WHICH DESIGNED THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWGBJ 04TAPER,PIN PIN TAPER THE AMOUNT OF TAPER MEASURED PARALLEL TO THE LONGITUDINAL AXIS OF THE PIN PER MEASUREMENT SCALE. 1D AND 1B MODE REPLY11AB39 CWGCA 13THREAD SIZE DESIGNATOR,BORE,FIRST END FIRST END BORE THREAD SIZE DESIGNATOR NONE. 1A MODE REPLY 0 CWGDJ 04DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO HEIGHT,CENTER TO CENTER,NOMINAL NOMINAL CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO HEIGHT THE NOMINAL CENTER TO CENTER DISTANCE BETWEEN THE MOUNTING FACILITIES PARALLEL TO THE HEIGHT. 1D AND 1B MODE REPLY11AA05 CWGFJ 04DIAMETER,COUNTERBORE COUNTERBORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWGGJ 04HEIGHT,FACE,RAISED,FIRST DISCHARGE FLANGE FIRST DISCHARGE FLANGE RAISED FACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CWGHJ 10CURRENT RATING,OUTPUT OUTPUT CURRENT RATING THE OUTPUT CURRENT RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE. 3D AND 1B MODE REPLY31AB621AC301AC20 CWGJA 12QUANTITY,HOLE,BOLT CIRCLE,FIRST FIRST BOLT CIRCLE HOLE QUANTITY NONE. 1A MODE REPLY 0 CWGKD 19POSITION,BURNING BURNING POSITION THE POSITION IN WHICH THE ITEM IS DESIGNED TO OPERATE. SELECT REPLY CODE 10AF63 CWGLJ 10CURRENT RATING IN AMPS CURRENT RATING IN AMPS THE AMOUNT OF CURRENT FOR WHICH AN ITEM IS RATED,EXPRESSED IN AMPERES. 1D AND 1B MODE REPLY13AN28 CWGMJ 10CURRENT RATING AT MAXIMUM RATED VOLTAGE,LOAD,AUXILIARY CONTACT AUXILIARY CONTACT LOAD CURRENT RATING AT MAXIMUM RATED VOLTAGE THE AMOUNT OF CURRENT THE AUXILIARY CONTACTS ARE RATED TO MAKE OR BREAK AT MAXIMUM RATED VOLTAGE,WITH A SPECIFIED LOAD. 2D AND 1B MODE REPLY22AN862AN87 CWGND 19PHASE,OUTPUT OUTPUT PHASE THE NUMBER OF OUTPUT ALTERNATING CURRENT PHASES. SELECT REPLY CODE 10AD02 CWGPJ 10OUTPUT RATING,POWER,MODULATOR MODULATOR POWER OUTPUT RATING THE RATED POWER OUTPUT FOR WHICH THE MODULATOR IS DESIGNED. 2D AND 1B MODE REPLY22AB491AC20 CWGQJ 18TYPE AND VOLTAGE RATING IN VOLTS,CONNECTION CONNECTION TYPE AND VOLTAGE RATING IN VOLTS INDICATES THE TYPE OF CONNECTION,RATING SEQUENCE,AND VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN VOLTS. 2D AND 1B MODE REPLY23AN993AN28 CWGRJ 04ANGLE FROM HORIZONTAL CENTERLINE,FITTING,LUBRICATION LUBRICATION FITTING ANGLE FROM HORIZONTAL CENTERLINE THE ANGLE OF THE LUBRICATION FITTING FROM THE HORIZONTAL CENTERLINE OF THE ITEM. 2D AND 1B MODE REPLY21AP381AC20 CWGSH 19WAVEFORM AND CURRENT TYPE,OUTPUT OUTPUT WAVEFORM AND CURRENT TYPE THE OUTPUT WAVEFORM OF THE CURRENT AT THE OUTPUT TERMINALS. 2D MODE REPLY 22AJ521AB62 CWGTJ 04ANGLE,HEAD,LARGE END LARGE END HEAD ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CWGWD 19CHARACTERISTICS,CURRENT/VOLTAGE,OUTPUT,POWER SUPPLY POWER SUPPLY OUTPUT CURRENT/VOLTAGE CHARACTERISTICS AN INDICATION OF WHETHER CURRENT OR VOLTAGE OR BOTH ARE CONTROLLED,STABILIZED,OR LIMITED TO OBTAIN THE REQUIRED OUTPUT POWER CHARACTERISTICS. SELECT REPLY CODE 10AL74 CWGXJ 04DISTANCE FROM HORIZONTAL CENTERLINE TO CENTER OF LOWER HOLE DISTANCE FROM HORIZONTAL CENTERLINE TO CENTER OF LOWER HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 CWGYD 11METHOD,LOCKING,ROTATING ELEMENT ROTATING ELEMENT LOCKING METHOD THE MEANS OF LOCKING THE ROTATING ELEMENT OF THE BEARING TO THE SHAFT. SELECT REPLY CODE 10AM39 CWGZJ 10VOLTAGE AT FULL LOAD,RIPPLE RIPPLE VOLTAGE AT FULL LOAD THE MAXIMUM ALTERNATING CURRENT VOLTAGE VARIATION WHICH MAY BE PRESENT ON THE DIRECT CURRENT OUTPUT VOLTAGE LEVEL. 2D AND 1B MODE REPLY21AB631AF65 CWHBJ 04DIAMETER,COUNTERSINK,SECOND END SECOND END COUNTERSINK DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWHCD 08LOCATION,CONTROL,OUTPUT OUTPUT CONTROL LOCATION INDICATES THE LOCATION OF THE OUTPUT CONTROL(S). SELECT REPLY CODE 10AJ91 CWHDJ /D/ 04HEIGHT,FACE,RAISED,SECOND INTAKE FLANGE SECOND INTAKE FLANGE RAISED FACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CWHFA 12QUANTITY,CONNECTION,OUTPUT OUTPUT CONNECTION QUANTITY THE NUMBER OF ELECTRICAL OUTPUT CONNECTIONS ON THE ITEM. 1A MODE REPLY 0 CWHGA 13THREAD SIZE DESIGNATOR,BORE,SECOND END SECOND END BORE THREAD SIZE DESIGNATOR NONE. 1A MODE REPLY 0 CWHHJ 04DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF TENTH DIAMETER DISTANCE FROM LARGEST BEARING SURFACE OF HEAD TO END OF TENTH DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWHJD 18TYPE,CONNECTION,OUTPUT OUTPUT CONNECTION TYPE INDICATES THE TYPE OF ELECTRICAL OUTPUT CONNECTION. SELECT REPLY CODE 10AN89 CWHKJ 10SPEED RATING,SHAFT,OUTPUT,GEARED HEAD GEARED HEAD OUTPUT SHAFT SPEED RATING THE SPEED RATING OF THE GEARED HEAD OUTPUT SHAFT(S). 2D AND 1B MODE REPLY23AN283AJ40 CWHMJ 10CURRENT RATING,INPUT INPUT CURRENT RATING THE AMOUNT OF INPUT CURRENT FOR WHICH THE ITEM IS RATED. 3D AND 1B MODE REPLY31AB621AC301AC20 CWHNJ 04WIDTH,OPENING,HOUSING HOUSING OPENING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWHPA 12QUANTITY,HOLE,BOLT CIRCLE,SECOND SECOND BOLT CIRCLE HOLE QUANTITY NONE. 1A MODE REPLY 0 CWHQD 18TYPE,CONNECTION,INPUT INPUT CONNECTION TYPE INDICATES THE TYPE OF ELECTRICAL INPUT CONNECTION. SELECT REPLY CODE 10AN89 CWHRJ 04ANGLE OF SHAFT TO MOUNTING BASE ANGLE OF SHAFT TO MOUNTING BASE THE ANGLE OF THE SHAFT IN RELATION TO THE MOUNTING BASE. 1D AND 1B MODE REPLY11AP38 CWHSJ 04DISTANCE BETWEEN GROOVES DISTANCE BETWEEN GROOVES NONE. 2D AND 1B MODE REPLY21AA051AC20 CWHTA 12QUANTITY,CONNECTION,INPUT INPUT CONNECTION QUANTITY THE NUMBER OF ELECTRICAL INPUT CONNECTIONS ON THE ITEM. 1A MODE REPLY 0 CWHWJ 04DISTANCE FROM VERTICAL CENTERLINE TO CENTER OF RIGHT HOLE DISTANCE FROM VERTICAL CENTERLINE TO CENTER OF RIGHT HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 CWHXJ 04DEPTH,COUNTERBORE COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWHYH 07FEATURE AND TYPE,BATTERY BATTERY FEATURE AND TYPE AN INDICATION OF WHETHER OR NOT THE BATTERY IS RECHARGEABLE AND THE TYPE OF BATTERY. 2D MODE REPLY 23AK952AP68 CWHZJ A19CHARACTERISTIC,END,SHAFT SHAFT END CHARACTERISTIC AN INDICATION OF THE CHARACTERISTIC(S) OF THE SHAFT END. 1D AND 1A MODE REPLY13AK54 CWJBJ 10POWER RATING,ELEMENT,ENERGIZING ENERGIZING ELEMENT POWER RATING THE AMOUNT OF ELECTRICAL ENERGY WHICH THE ENERGIZING ELEMENT IS CAPABLE OF DISSIPATING AT ITS RATED VOLTAGE AND/OR CURRENT DURING NORMAL OPERATION. 1D AND 1B MODE REPLY12AN86 CWJCB 10PERCENTAGE BY VOLUME,CONTENT,WATER,MAXIMUM MAXIMUM WATER CONTENT PERCENTAGE BY VOLUME A MEASUREMENT OF THE MAXIMUM WATER CONTENT OF THE ITEM,EXPRESSED IN PERCENT BY VOLUME. 1B MODE REPLY 0 CWJDJ 04DIAMETER,UNDERCUT,SHAFT SHAFT UNDERCUT DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWJFD 08LOCATION,BATTERY BATTERY LOCATION INDICATES THE LOCATION OF THE BATTERY. SELECT REPLY CODE 10AJ91 CWJGJ 04ANGLE BETWEEN EXTERNAL KEYS ANGLE BETWEEN EXTERNAL KEYS NONE. 1D AND 1B MODE REPLY11AP38 CWJHJ 04ANGLE,EDGE EDGE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CWJJD 19CONDITION,SURFACE,LENS FACE LENS FACE SURFACE CONDITION THE CONDITION OF THE LENS FACE WITH RESPECT TO THE TEXTURE OF THE SURFACE. SELECT REPLY CODE 10AN72 CWJKD 09MATERIAL,CASE CASE MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE CASE IS FABRICATED. PLEASE USE MRC MATT WITH ISAC TABLE 0326 IN PLACE OF THIS CANCELED MRC. SELECT REPLY CODE 10MA01 CWJLB /D/ 13THREAD PITCH IN MILLIMETERS,INTAKE,SECOND SECOND INTAKE THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CWJMJ 04DISTANCE FROM CENTER OF PLATE TO FLAT DISTANCE FROM CENTER OF PLATE TO FLAT NONE. 2D AND 1B MODE REPLY21AA051AC20 CWJNJ 04DISTANCE FROM HORIZONTAL CENTERLINE TO CENTER OF RIGHT HOLE DISTANCE FROM HORIZONTAL CENTERLINE TO CENTER OF RIGHT HOLE NONE. 2D AND 1B MODE REPLY21AA051AC20 CWJPJ /D/ 04DISTANCE FROM CENTER OF SECOND END TO EDGE OF FIRST MOUNTING END DISTANCE FROM CENTER OF SECOND END TO EDGE OF FIRST MOUNTING END NONE. 2D AND 1B MODE REPLY21AA051AC20 CWJQJ 04ANGLE,CUT,END END CUT ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CWJRJ 04RADIUS,FLUTE FLUTE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CWJSJ 10VOLTAGE,OPERATING,WINDING WINDING OPERATING VOLTAGE THE VALUE/S/ OF THE OPERATING VOLTAGE APPLIED TO THE WINDING. 3D AND 1B MODE REPLY31AB621AB631AC20 CWJTJ 10STRENGTH,YIELD,OFFSET OFFSET YIELD STRENGTH THE MAXIMUM LOAD WHICH CAN BE APPLIED TO THE MATERIAL IN LONGITUDINAL DIRECTION PER CROSS-SECTIONAL UNIT WITH A REMAINING PERMANENT ELONGATION OF 0.2 PERCENT OF THE MEASURED LENGTH. 1D AND 1B MODE REPLY11AB18 CWJWD 18TYPE,HOLE,MOUNTING MOUNTING HOLE TYPE INDICATES THE TYPE OF MOUNTING HOLE(S) PROVIDED ON THE ITEM. SELECT REPLY CODE 10AF58 CWJXJ 04LENGTH OF FLAT ALONG BASE LENGTH OF FLAT ALONG BASE NONE. 2D AND 1B MODE REPLY21AA051AC20 CWJYD 11METHOD,ATTACHMENT,OPTICAL FIBER OPTICAL FIBER ATTACHMENT METHOD THE MEANS FOR ATTACHING THE OPTICAL FIBER TO THE ITEM. SELECT REPLY CODE 10AM39 CWJZJ 04DIAMETER,CIRCLE,TERMINAL TERMINAL CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TERMINAL CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWKBJ 04DIAMETER,INSIDE,FIRST EYE FIRST EYE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWKCD 17SURFACE TREATMENT,CASE CASE SURFACE TREATMENT THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE CASE SURFACE(S) AND CANNOT BE WIPED OFF. SELECT REPLY CODE 10SF01 CWKDH 18TYPE AND LOCATION,GUIDE,ROUND ROUND GUIDE TYPE AND LOCATION INDICATES THE TYPE OF ROUND POLARIZING GUIDE INCLUDED ON THE ITEM AND ITS LOCATION. 2D MODE REPLY 22AP523AN73 CWKFD 17SURFACE TREATMENT,OVERALL OVERALL SURFACE TREATMENT THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE OVERALL ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF. SELECT REPLY CODE 10SF01 CWKGD 18TYPE,DESIGN,VENTILATION VENTILATION DESIGN TYPE INDICATES THE TYPE OF DESIGN PROVIDED FOR VENTILATION OF THE ITEM. SELECT REPLY CODE 10AN05 CWKHJ /D/ 04LENGTH OF BRUSH PART,THIRD BRUSH THIRD BRUSH LENGTH OF BRUSH PART NONE. 2D AND 1B MODE REPLY21AA051AC20 CWKJJ A13THREAD TOLERANCE CLASS,HOLE,MOUNTING MOUNTING HOLE THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITIONS AND GRADES OF A MOUNTING HOLE THREAD. 1D AND 1A MODE REPLY13AN73 CWKKJ 04ANGLE,INSIDE,RIGHT BOTTOM RIGHT BOTTOM INSIDE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CWKLJ 04ANGLE,INCLUDED,SERRATION SERRATION INCLUDED ANGLE THE ANGLE INCLUDED IN SERRATIONS. 2D AND 1B MODE REPLY21AP381AC20 CWKMA 10TIME IN MINUTES,WARM UP WARM UP TIME IN MINUTES THE TIME REQUIRED FOR A POWER SUPPLY(IES) TO REACH THE FULL OPERATING POTENTIAL FOR WHICH IT IS RATED,EXPRESSED IN MINUTES. 1A MODE REPLY 0 CWKNG 19ADDITIVE,PERMISSIBLE PERMISSIBLE ADDITIVE THOSE PERMISSIBLE ADDITIVES USED TO IMPART A DESIRED CHARACTERISTIC. FULL TEXT WRITE-IN 0 CWKPJ 04ANGLE BETWEEN CENTERLINE OF HOLES ANGLE BETWEEN CENTERLINE OF HOLES NONE. 1D AND 1B MODE REPLY11AP38 CWKQB 13THREAD PITCH IN MILLIMETERS,DISCHARGE,FIRST FIRST DISCHARGE THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CWKRJ 04DISTANCE BETWEEN HOLE CENTERS ALONG BASE DISTANCE BETWEEN HOLE CENTERS ALONG BASE NONE. 2D AND 1B MODE REPLY21AA051AC20 CWKSJ 10LOAD,TEST,PROOF PROOF TEST LOAD A SPECIFIED TEST LOAD WHICH THE ITEM MUST WITHSTAND WITHOUT DAMAGE. 1D AND 1B MODE REPLY12AN75 CWKTJ 04LENGTH OF FLAT ALONG SIDE LENGTH OF FLAT ALONG SIDE NONE. 2D AND 1B MODE REPLY21AA051AC20 CWKWJ 04DIAMETER,SURFACE,RAISED,INSIDE INSIDE RAISED SURFACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWKXJ /D/ 04DISTANCE FROM CENTER OF SECOND END TO EDGE OF SECOND MOUNTING END DISTANCE FROM CENTER OF SECOND END TO EDGE OF SECOND MOUNTING END NONE. 2D AND 1B MODE REPLY21AA051AC20 CWKYJ 04DIAMETER,CIRCLE,INNER TERMINAL INNER TERMINAL CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INNER TERMINAL CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWKZJ 04DIAMETER,THREAD,NOMINAL,MOUNTING FACILITY MOUNTING FACILITY NOMINAL THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE NOMINAL THREADED PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWLBJ /D/ 04HEIGHT,FACE,RAISED,SECOND DISCHARGE FLANGE SECOND DISCHARGE FLANGE RAISED FACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CWLCJ 04RADIUS FROM CENTER OF PLATE TO END OF LUG RADIUS FROM CENTER OF PLATE TO END OF LUG NONE. 2D AND 1B MODE REPLY21AA051AC20 CWLDJ 04DISTANCE BETWEEN HOLE CENTERS ALONG HEIGHT DISTANCE BETWEEN HOLE CENTERS ALONG HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CWLFJ A13THREAD TOLERANCE CLASS,MOUNTING FACILITY MOUNTING FACILITY THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE OF A MOUNTING FACILITY THREAD. 1D AND 1A MODE REPLY13AN73 CWLGD 19ARRANGEMENT,PATTERN,TERMINAL TERMINAL PATTERN ARRANGEMENT THE ARRANGEMENT OF TERMINAL POSITIONS ON THE ITEM. SELECT REPLY CODE 10AH86 CWLHJ /D/ 04LENGTH ACROSS LUGS LENGTH ACROSS LUGS NONE. 2D AND 1B MODE REPLY21AA051AC20 CWLJJ 04DIAMETER,MAJOR MAJOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CWLKJ 04DIAMETER,SURFACE,RAISED,OUTSIDE OUTSIDE RAISED SURFACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWLLJ 04DIAMETER,MINOR MINOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CWLMJ /D/ 04WIDTH ACROSS LUGS WIDTH ACROSS LUGS NONE. 2D AND 1B MODE REPLY21AA051AC20 CWLND 02DESIGN,TERMINAL TERMINAL DESIGN THE DESIGN OF THE TERMINAL. SELECT REPLY CODE 10AH21 CWLPA /D/ 03DESIGNATOR,SIZE,PIPE PIPE SIZE DESIGNATOR A DESIGNATION INDICATING THE SIZE OF THE PIPE. 1A MODE REPLY 0 CWLQJ 04ANGLE BETWEEN FLATS,END,FIRST FIRST END ANGLE BETWEEN FLATS NONE. 2D AND 1B MODE REPLY21AF981AC20 CWLRJ T10RANGE,TEMP,RATED EFFECTIVE RATED EFFECTIVE TEMP RANGE THE RATED EFFECTIVE TEMPERATURE RANGE OF THE ITEM. 1D AND 1F MODE REPLY11AB36 CWLSD 19CAPABILITY,SWITCHING SWITCHING CAPABILITY THE PROVISION FOR SINGLE OR MULTIPLE POINT SETTING(S) AT PREDETERMINED SHAFT SPEED(S) IN ORDER TO ACTIVATE AN ALARM OR CONTROL OR FOR SPEED VERIFICATION. SELECT REPLY CODE 10AK54 CWLTJ 04DIAMETER ACCOMMODATED,CONDUCTOR,OPTICAL OPTICAL CONDUCTOR DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE OPTICAL CONDUCTOR,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CWLWJ 10TEMP RATING,INPUT INPUT TEMP RATING THE INPUT TEMPERATURE RATING OF THE ITEM. 1D AND 1B MODE REPLY11AB36 CWLXJ 04DIAMETER,INSIDE,HOUSING HOUSING INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWLYD 18TYPE,BEARING,PRIME MOVER DRIVE SHAFT PRIME MOVER DRIVE SHAFT BEARING TYPE INDICATES THE TYPE OF BEARING/S/ PROVIDED ON THE PRIME MOVER DRIVE SHAFT. SELECT REPLY CODE 10AH96 CWLZJ 04SIZE ACCOMMODATED,CONDUCTOR,OPTIC FIBER OPTIC FIBER CONDUCTOR SIZE ACCOMMODATED DESIGNATES THE SIZE OF THE OPTIC FIBER CONDUCTOR ACCOMMODATED BY THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CWMBJ 04ANGLE,Y,END,FIRST FIRST END Y ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CWMCA /D/ 03DESIGNATOR,SIZE,HOSE HOSE SIZE DESIGNATOR A DESIGNATION INDICATING THE SIZE OF THE HOSE. 1A MODE REPLY 0 CWMDJ 10POWER RATING,COMPRESSOR COMPRESSOR POWER RATING THE VALUE OF THE ELECTRICAL INPUT POWER FOR WHICH THE COMPRESSOR IS RATED. 1D AND 1B MODE REPLY11AC33 CWMFJ 04DIAMETER,FACE,RAISED,FIRST INTAKE FLANGE FIRST INTAKE FLANGE RAISED FACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWMGJ /D/ 10VOLTAGE RATING IN VOLTS,DC,MAXIMUM,CONTACT CONTACT MAXIMUM DC VOLTAGE RATING IN VOLTS THE MAXIMUM DIRECT CURRENT POTENTIAL THAT MAY BE APPLIED CONTINUOUSLY TO THE CONTACT WITHOUT DAMAGE,EXPRESSED IN VOLTS. 2D AND 1B MODE REPLY21AP551AP56 CWMHJ /D/ 04THICKNESS,END,FIRST FIRST END THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CWMJJ /D/ 04DISTANCE BETWEEN LUGS,END,SECOND SECOND END DISTANCE BETWEEN LUGS THE DISTANCE BETWEEN THE LUGS OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CWMKJ 04DIAMETER,INSIDE,FITTING FITTING INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWMLJ 04LENGTH BEYOND BEAD,END END LENGTH BEYOND BEAD NONE. 2D AND 1B MODE REPLY21AA051AC20 CWMMJ /D/ 04DIAMETER,HOLE,BOLT,FIRST END FIRST END BOLT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CWMNJ /D/A13THREAD TOLERANCE CLASS,OUTLET OUTLET THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITIONS AND GRADES OF AN OUTLET THREAD. 1D AND 1A MODE REPLY13AN73 CWMPJ 10CAPACITY IN BTU PER HOUR,NOMINAL NOMINAL CAPACITY IN BTU PER HOUR THE NOMINAL CAPACITY OF THE ITEM TO COOL OR HEAT,EXPRESSED IN BRITISH THERMAL UNITS PER HOUR. 1D AND 1B MODE REPLY13AK95 CWMQB 10WATTAGE RATING IN KILOWATTS,HEATER HEATER WATTAGE RATING IN KILOWATTS THE RATED POWER THE HEATER CAN SAFELY CONSUME OR PROVIDE,MEASURED IN KILOWATTS. 1B MODE REPLY 0 CWMRJ 04DISTANCE BETWEEN FOURTH AND FIFTH HOLE CENTERS ALONG WIDTH,FIRST LEG FIRST LEG DISTANCE BETWEEN FOURTH AND FIFTH HOLE CENTERS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWMSJ A13THREAD TOLERANCE CLASS,MOUNTING MOUNTING THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE OF A MOUNTING THREAD. 1D AND 1A MODE REPLY13AN73 CWMTJ 10DIOPTER,INSIDE,SPHERE CURVE SPHERE CURVE INSIDE DIOPTER NONE. 2D AND 1B MODE REPLY21AH081AC20 CWMWD 18TYPE,TEETH TEETH TYPE INDICATES THE TYPE OF TEETH INCLUDED ON THE ITEM. SELECT REPLY CODE 10AL23 CWMXJ 04LENGTH,CUTOUT,FIRST LEG FIRST LEG CUTOUT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWMYJ 04HEIGHT,PITCH PITCH HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CWMZJ 04WIDTH,CUTOUT,FIRST LEG FIRST LEG CUTOUT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWNBJ /D/ 04DIAMETER,HOLE,BOLT,SECOND END SECOND END BOLT HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CWNCJ 04DISTANCE BETWEEN FOURTH AND FIFTH HOLE CENTERS ALONG WIDTH,SECOND LEG SECOND LEG DISTANCE BETWEEN FOURTH AND FIFTH HOLE CENTERS ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWNDJ 10DIOPTER,OUTSIDE,SPHERE CURVE SPHERE CURVE OUTSIDE DIOPTER NONE. 2D AND 1B MODE REPLY21AH081AC20 CWNFG /D/ 10RATING IN LITERS PER MINUTE AT SPECIFIED PRESSURE IN BAR,OUTPUT,FLUID FLUID OUTPUT RATING IN LITERS PER MINUTE AT SPECIFIED PRESSURE IN BAR THE RATED CAPACITY OF THE FLUID OUTPUT DELIVERED BY THE ITEM,EXPRESSED IN LITERS PER MINUTE AT A SPECIFIC PRESSURE IN BAR. FULL TEXT WRITE-IN 0 CWNGB 10SPEED IN RPM,KILOWATT RATING,ENGINE ENGINE KILOWATT RATING SPEED IN RPM THE ROTARY SPEED OF THE ENGINE AT WHICH THE KILOWATT RATING IS DETERMINED,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 CWNHD 19FORM,TOOTH TOOTH FORM AN INDICATION AS TO WHETHER THE TEETH ARE A STANDARD DEPTH OR MODIFIED TO A SHORTER DEPTH. SELECT REPLY CODE 10AK54 CWNJD 09MATERIAL,ELECTRODE,CAPACITIVE CAPACITIVE ELECTRODE MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE CAPACITIVE ELECTRODE IS FABRICATED. SELECT REPLY CODE 10MA01 CWNKJ 04DIAMETER,NOMINAL,FLANGE FLANGE NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CWNLJ 10MARKING,TEMP,PRECALIBRATED PRECALIBRATED TEMP MARKING THE PRECALIBRATED TEMPERATURE LEVEL(S) IN DEGREES,AT WHICH A SENSITIZED STICKER OR TAB,OR A SERIES OF STICKERS OR TABS,WILL CHANGE COLOR. 1D AND 1B MODE REPLY11AB36 CWNMD 05DIRECTION,TOOTH TOOTH DIRECTION THE DIRECTION THE TEETH CURVE WHEN VIEWED FROM THE EDGE OF THE ITEM. SELECT REPLY CODE 10AA38 CWNNJ 04LENGTH,CUTOUT,SECOND LEG SECOND LEG CUTOUT LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWNPJ 04RADIUS,NOMINAL,THROAT THROAT NOMINAL RADIUS A NOMINAL MEASUREMENT OF THE THROAT RADIUS ACROSS THE FACE OF THE ITEM. 1D AND 1B MODE REPLY11AA05 CWNQJ 10DIOPTER,INSIDE,CYLINDER CURVE CYLINDER CURVE INSIDE DIOPTER NONE. 2D AND 1B MODE REPLY21AH081AC20 CWNRB /D/ 13THREAD PITCH IN MILLIMETERS,DISCHARGE,SECOND SECOND DISCHARGE THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CWNSG /D/ 10RATING IN CUBIC METERS PER MINUTE AT SPECIFIED PRESSURE IN BAR,OUTPUT,AIR AIR OUTPUT RATING IN CUBIC METERS PER MINUTE AT SPECIFIED PRESSURE IN BAR THE RATED CAPACITY OF THE AIR OUTPUT DELIVERED BY THE ITEM,EXPRESSED IN CUBIC METERS PER MINUTE AT A SPECIFIC PRESSURE IN BAR. FULL TEXT WRITE-IN 0 CWNTJ 04DIAMETER,OUTSIDE,INNER WALL INNER WALL OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWNWJ 04DIAMETER,PITCH,MATING MATING PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF THE MATING ITEM. 2D AND 1B MODE REPLY21AA051AC20 CWNXJ 04WIDTH,CUTOUT,SECOND LEG SECOND LEG CUTOUT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWNYJ 04LENGTH,NOMINAL,PILOT PILOT NOMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CWNZA 13THREAD CLASS,INTAKE,FIRST FIRST INTAKE THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD. 1A MODE REPLY 0 CWPBJ /D/ 10CAPACITY IN WATTS,NOMINAL NOMINAL CAPACITY IN WATTS THE NOMINAL CAPACITY OF THE ITEM,EXPRESSED IN WATTS. 1D AND 1B MODE REPLY13AK95 CWPCA 12QUANTITY,THREAD FORM THREAD FORM QUANTITY THE NUMBER OF THREAD FORMS THAT PROGRESS HELICALLY AROUND THE AXIS. 1A MODE REPLY 0 CWPDJ 04ANGLE,CHAMFER,FIRST LEG FIRST LEG CHAMFER ANGLE NONE. REPLACED BY MRC CSYT WITH ISAC 0368. 2D AND 1B MODE REPLY21AP381AC20 CWPFJ 10DIOPTER,OUTSIDE,CYLINDER CURVE CYLINDER CURVE OUTSIDE DIOPTER NONE. 2D AND 1B MODE REPLY21AH081AC20 CWPGJ 04ANGLE,CHAMFER,SECOND LEG SECOND LEG CHAMFER ANGLE NONE. REPLACED BY MRC CSYT WITH ISAC 0368. 2D AND 1B MODE REPLY21AP381AC20 CWPHD 05DIRECTION,THREAD FORM THREAD FORM DIRECTION THE DIRECTION OF THE THREAD FORM WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD FORM WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD FORM WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 CWPJB /D/ 10CAPACITY RATING IN CUBIC METERS PER MINUTE,DISPLACEMENT,AIR AIR DISPLACEMENT CAPACITY RATING IN CUBIC METERS PER MINUTE THE RATED CAPACITY OF THE AIR VOLUME DISPLACED BY THE ITEM,EXPRESSED IN CUBIC METERS PER MINUTE. 1B MODE REPLY 0 CWPKJ 10RESISTANCE AT REFERENCE TEMP,INSULATION INSULATION RESISTANCE AT REFERENCE TEMP DIRECT CURRENT RESISTANCE BETWEEN TWO CONDUCTORS THAT ARE SEPARATED BY AN INSULATING MATERIAL,MEASURED AT REFERENCE TEMPERATURE. 1D AND 1B MODE REPLY12AN86 CWPLA 12QUANTITY,THREAD LEAD,MATING MATING THREAD LEAD QUANTITY THE NUMBER OF THREAD LEADS ON THE MATING ITEM. 1A MODE REPLY 0 CWPMB 10FACTOR AT REFERENCE TEMP IN PERCENT,DISSIPATION DISSIPATION FACTOR AT REFERENCE TEMP IN PERCENT THE RATIO OF RESISTANCE TO CAPACITIVE REACTANCE MEASURED AT REFERENCE TEMPERATURE. 1B MODE REPLY 0 CWPNB 10FACTOR AT REFERENCE TEMP IN PERCENT,POWER POWER FACTOR AT REFERENCE TEMP IN PERCENT THE RATIO OF RESISTANCE TO IMPEDANCE MEASURED AT REFERENCE TEMPERATURE. 1B MODE REPLY 0 CWPPJ 04ANGLE,PRESSURE PRESSURE ANGLE THE MEASUREMENT OF THE PRESSURE ANGLE ON THE ITEM. 1D AND 1B MODE REPLY11AP38 CWPQJ /D/ 10OUTPUT POWER RATING,RECOMMENDED,BOILER BOILER RECOMMENDED OUTPUT POWER RATING THE RECOMMENDED OUTPUT POWER AT WHICH THE BOILER IS RATED. 1D AND 1B MODE REPLY11AC33 CWPRJ 04DISTANCE FROM PIVOT PINHOLE CENTER TO BASE LINE OF ANGLED PART DISTANCE FROM PIVOT PINHOLE CENTER TO BASE LINE OF ANGLED PART NONE. 2D AND 1B MODE REPLY21AA051AC20 CWPSJ 04THICKNESS,NOMINAL,FLANGE FLANGE NOMINAL THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 CWPTA 12QUANTITY,ROW,TUBE TUBE ROW QUANTITY THE NUMBER OF ROWS OF TUBES. 1A MODE REPLY 0 CWPWD /D/ 09MATERIAL,FIN FIN MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE FIN IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CWPXJ 04WIDTH,COIL COIL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE COIL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CWPYJ T10RANGE,ENTERING,VALUE VALUE ENTERING RANGE THE MINIMUM AND MAXIMUM VALUES THAT CAN BE ENTERED. 1D AND 1F MODE REPLY12AP72 CWPZJ 04ANGLE,HELIX HELIX ANGLE THE MEASUREMENT OF THE HELIX ANGLE ON THE ITEM. 1D AND 1B MODE REPLY11AP38 CWQBJ 04ANGLE,COUNTERSINK,MATED SURFACE,FIRST END FIRST END MATED SURFACE COUNTERSINK ANGLE THE COUNTERSINK ANGLE OF THE FIRST END MATED SURFACE. 1D AND 1B MODE REPLY11AP38 CWQCB 10RESISTANCE AT REFERENCE TEMP IN OHMS,EQUIVALENT SERIES EQUIVALENT SERIES RESISTANCE AT REFERENCE TEMP IN OHMS ALL INTERNAL SERIES RESISTANCES CONCENTRATED OR LUMPED AT ONE POINT IN THE CIRCUIT AND TREATED AS ONE RESISTANCE,MEASURED AT REFERENCE TEMPERATURE IN OHMS. 1B MODE REPLY 0 CWQDJ 04ANGLE,PITCH PITCH ANGLE THE MEASUREMENT OF THE PITCH ANGLE ON THE ITEM. 1D AND 1B MODE REPLY11AP38 CWQFB 10FACTOR AT REFERENCE TEMP,QUALITY QUALITY FACTOR AT REFERENCE TEMP THE RATIO OF CAPACITIVE REACTANCE TO RESISTANCE,MEASURED AT REFERENCE TEMPERATURE. 1B MODE REPLY 0 CWQGJ 04ANGLE,SKEWED SKEWED ANGLE NONE. 1D AND 1B MODE REPLY11AP38 CWQHJ 10LEAKAGE AT REFERENCE TEMP,DC DC LEAKAGE AT REFERENCE TEMP STRAY DIRECT CURRENT OF RELATIVELY SMALL VALUE FLOWS THROUGH THE CAPACITOR WHEN VOLTAGE IS IMPRESSED ACROSS IT,MEASURED AT REFERENCE TEMPERATURE. 1D AND 1B MODE REPLY12AN86 CWQJA 13THREAD TOLERANCE CLASS,INTERNAL INTERNAL THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE OF AN INTERNAL THREAD. 1A MODE REPLY 0 CWQKJ 04DIAMETER,FACE,RAISED,FIRST DISCHARGE FLANGE FIRST DISCHARGE FLANGE RAISED FACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWQLJ 04DISTANCE BETWEEN BODY FACE AND PROTRUDING HUB END,NOMINAL NOMINAL DISTANCE BETWEEN BODY FACE AND PROTRUDING HUB END THE NOMINAL DISTANCE BETWEEN THE BODY FACE AND THE PROTRUDING HUB END. 1D AND 1B MODE REPLY11AA05 CWQMJ /D/ 04THICKNESS FOR WHICH DESIGNED,BLADE BLADE THICKNESS FOR WHICH DESIGNED THE THICKNESS OF THE BLADE FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY21AA051AC20 CWQNJ 04LENGTH,NOMINAL,HUB HUB NOMINAL LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE HUB,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CWQPA 12QUANTITY,BOLT HOLE,SMALLEST SMALLEST BOLT HOLE QUANTITY NONE. 1A MODE REPLY 0 CWQQJ 10TEMP AT WHICH RATED,REFERENCE REFERENCE TEMP AT WHICH RATED THE REFERENCE TEMPERATURE AT WHICH A RATING IS ESTABLISHED. 1D AND 1B MODE REPLY11AB36 CWQRJ 04DISTANCE BETWEEN BODY FACE AND RECESSED HUB END,NOMINAL NOMINAL DISTANCE BETWEEN BODY FACE AND RECESSED HUB END THE NOMINAL DISTANCE BETWEEN THE BODY FACE AND THE RECESSED HUB END. 1D AND 1B MODE REPLY11AA05 CWQSJ 04DIAMETER,INSIDE,NOMINAL,INLET INLET NOMINAL INSIDE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INLET,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWQTJ 04DIAMETER TUBE ACCOMMODATED,INSIDE,NOMINAL NOMINAL INSIDE DIAMETER TUBE ACCOMMODATED THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWQWJ /D/ 10CAPABILITY,CUTTING,MAXIMUM,SHEET STEEL SHEET STEEL MAXIMUM CUTTING CAPABILITY THE MAXIMUM SHEET STEEL THICKNESS THE ITEM IS CAPABLE OF CUTTING. 1D AND 1B MODE REPLY11AA05 CWQXJ /D/ 13THREAD PITCH,PERFORATION PERFORATION THREAD PITCH THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE PERFORATION THREAD AXIS. 1D AND 1B MODE REPLY11AA05 CWQYJ 04WIDTH,INSIDE,FITTING FITTING INSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWQZA 12QUANTITY,BOLT HOLE,LARGEST LARGEST BOLT HOLE QUANTITY NONE. 1A MODE REPLY 0 CWRBJ 04DEPTH,NOMINAL,RECESS,BODY BODY RECESS NOMINAL DEPTH A NOMINAL MEASUREMENT BETWEEN SPECIFIED POINTS ON THE RECESS OF THE BODY,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 CWRCJ 04DIAMETER,OUTSIDE,NOMINAL,INLET INLET NOMINAL OUTSIDE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INLET,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWRDJ 04ANGLE,COUNTERSINK,MATED SURFACE,SECOND END SECOND END MATED SURFACE COUNTERSINK ANGLE THE COUNTERSINK ANGLE OF THE SECOND END MATED SURFACE. 1D AND 1B MODE REPLY11AP38 CWRFJ 04DIAMETER,NOMINAL,RECESS,BODY BODY RECESS NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY RECESS,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWRGJ 10CAPACITY,VALUE,DAILY TRANSACTION DAILY TRANSACTION VALUE CAPACITY THE DAILY TRANSACTION VALUE THAT CAN BE ACCUMULATED. 1D AND 1B MODE REPLY12AP72 CWRHA 13THREAD CLASS,DISCHARGE,FIRST FIRST DISCHARGE THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD. 1A MODE REPLY 0 CWRJD 11METHOD,ACTIVATION,MARKING MARKING ACTIVATION METHOD THE MEANS WHICH ACTIVATES STERILITY INDICATOR MARKINGS. SELECT REPLY CODE 10AB75 CWRKJ 04LENGTH,NOMINAL,BOSS BOSS NOMINAL LENGTH THE NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF A BOSS,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CWRLJ 10CAPACITY,VALUE,MAXIMUM MAXIMUM VALUE CAPACITY THE MAXIMUM VALUE THAT CAN BE ENTERED. 1D AND 1B MODE REPLY12AP72 CWRMJ 04WIDTH,NOMINAL,FACE FACE NOMINAL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FACE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CWRNJ 04DIAMETER,INSIDE,NOMINAL,OUTLET OUTLET NOMINAL INSIDE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTLET,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWRPJ 04DIAMETER,NOMINAL,BOSS BOSS NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOSS,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWRQB /D/ 13THREAD PITCH IN MILLIMETERS,FORWARD END FORWARD END THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT FORWARD END THREADS MEASURED PARALLEL TO THE THREADED AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CWRRJ 10FLOW RATE AND FLUID TYPE FLOW RATE AND FLUID TYPE THE AMOUNT OF FLOW PER UNIT OF MEASURE AND THE FLUID TYPE FOR WHICH THE ITEM IS DESIGNED. 2D AND 1B MODE REPLY22AG673AN91 CWRSJ 04DIAMETER,NOMINAL,BORE BORE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BORE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWRTJ /D/T10RANGE,SCALE,COMPUTING COMPUTING SCALE RANGE THE RANGE OF THE COMPUTING SCALE. 1D AND 1F MODE REPLY12AP72 CWRWJ 04ANGLE,OFFSET,SLOT,FIRST LEG FIRST LEG SLOT OFFSET ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CWRXJ 04DEPTH,NOMINAL,BORE BORE NOMINAL DEPTH A NOMINAL MEASUREMENT BETWEEN SPECIFIED POINTS ON THE BORE,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 CWRYB /D/ 13THREAD PITCH IN MILLIMETERS,REAR END REAR END THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT REAR END THREADS MEASURED PARALLEL TO THE THREADED AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CWRZD 18TYPE,EXPANDER EXPANDER TYPE INDICATES THE TYPE OF EXPANDER. SELECT REPLY CODE 10AJ57 CWSBJ 04WIDTH,NOMINAL,BORE BORE NOMINAL WIDTH A NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BORE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CWSCJ 04ANGLE,OFFSET,SLOT,SECOND LEG SECOND LEG SLOT OFFSET ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CWSDJ 04DIAMETER,OUTSIDE,NOMINAL,OUTLET OUTLET NOMINAL OUTSIDE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTLET,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWSFJ 04RADIUS,NOMINAL NOMINAL RADIUS THE NOMINAL DISTANCE FROM THE CENTER OF A CIRCULAR FIGURE OR BODY TO THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWSGD 17SURFACE TREATMENT,TERMINAL TERMINAL SURFACE TREATMENT THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED. THE TREATMENT IS DESIGNED TO PROTECT THE TERMINAL SURFACE(S) AND CANNOT BE WIPED OFF. SELECT REPLY CODE 10SF01 CWSHJ 04DISTANCE BETWEEN OUTER BODY FACE AND INNER FLANGE FACE,NOMINAL NOMINAL DISTANCE BETWEEN OUTER BODY FACE AND INNER FLANGE FACE NONE. 1D AND 1B MODE REPLY11AA05 CWSJB 10TIME IN HOURS,BURNING BURNING TIME IN HOURS THE DURATION OF LIGHT EMISSION PER BATTERY CHARGE,RATED IN HOURS. 1B MODE REPLY 0 CWSKJ 04DISTANCE FROM FLAT TO RADIAL CENTER,NOMINAL NOMINAL DISTANCE FROM FLAT TO RADIAL CENTER THE NOMINAL DISTANCE FROM THE FLAT TO THE RADIAL CENTER OF AN ITEM. 1D AND 1B MODE REPLY11AA05 CWSLJ /D/ 10INTERVAL,SCALE,COMPUTING COMPUTING SCALE INTERVAL THE INTERVAL VALUE ON A COMPUTING SCALE. 1D AND 1B MODE REPLY12AP72 CWSMJ 10BACKLASH,NORMAL NORMAL BACKLASH THE SMALLEST DISTANCE BETWEEN THE NONWORKING FLANKS OF TWO WHEELS WHEN THE WORKING FLANKS ARE IN CONTACT. 2D AND 1B MODE REPLY21AA051AC20 CWSNJ 04WIDTH,NOMINAL,KEYWAY KEYWAY NOMINAL WIDTH A NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A KEYWAY,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CWSPJ /D/ 04DISTANCE,OFFSET,BOTTOM HOLE TO UPPER LEFT HOLE CENTERLINE BOTTOM HOLE TO UPPER LEFT HOLE CENTERLINE OFFSET DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CWSQJ /D/A10COUNT,THREAD,MATERIAL MATERIAL THREAD COUNT THE NUMBER OF WARP THREADS (LENGTHWISE) AND FILL THREADS (CROSSWISE) PER UNIT OF MEASURE OF MATERIAL. 1D AND 1A MODE REPLY13AJ40 CWSRJ 04DISTANCE FROM BORE CENTER TO KEYWAY BOTTOM,NOMINAL NOMINAL DISTANCE FROM BORE CENTER TO KEYWAY BOTTOM THE NOMINAL DISTANCE FROM THE CENTER OF THE BORE TO THE BOTTOM OF THE KEYWAY(S). 1D AND 1B MODE REPLY11AA05 CWSSD 09MATERIAL,DIELECTRIC DIELECTRIC MATERIAL THE KIND OF INSULATING MEDIUM USED TO SEPARATE THE CAPACITOR ELECTRODES. SELECT REPLY CODE 10MA01 CWSTD 19ITEM FOR WHICH DISPENSER IS DESIGNED ITEM FOR WHICH DISPENSER IS DESIGNED THE ITEM FOR WHICH THE DISPENSER IS DESIGNED. SELECT REPLY CODE 10AK54 CWSWJ 04DIAMETER,NOMINAL,MAJOR,TAPER TAPER MAJOR NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CIRCULAR CROSS SECTION OF THE TAPERED PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWSXA 13THREAD CLASS,INTAKE,SECOND SECOND INTAKE THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD. 1A MODE REPLY 0 CWSYJ 04DIAMETER DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWSZD 09MATERIAL,INSULATION,CASE CASE INSULATION MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE CASE INSULATION IS FABRICATED. SELECT REPLY CODE 10MA01 CWTBJ 04DEPTH,NOMINAL,COUNTERBORE COUNTERBORE NOMINAL DEPTH A NOMINAL MEASUREMENT BETWEEN SPECIFIED POINTS OF THE COUNTERBORE,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 CWTCJ /D/ 04DIAMETER,FACE,RAISED,SECOND INTAKE FLANGE SECOND INTAKE FLANGE RAISED FACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWTDA 12QUANTITY,HOLE,CLAMPING CLAMPING HOLE QUANTITY THE NUMBER OF CLAMPING HOLES PROVIDED. 1A MODE REPLY 0 CWTFJ 04THICKNESS,FLANGE FLANGE THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE FLANGE, IN DISTICTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CWTGJ 04DIAMETER,NOMINAL,COUNTERBORE COUNTERBORE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COUNTERBORE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWTHJ 04DIAMETER,BODY BODY DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWTJA 03DESIGNATION AND SIZE ACCOMMODATED,TRADE,ITEM ITEM TRADE DESIGNATION AND SIZE ACCOMMODATED THE ALPHA-NUMERIC TRADE DESIGNATION AND SIZE OF THE ITEM ACCOMMODATED. 1A MODE REPLY 0 CWTKJ 13THREAD LENGTH,NOMINAL NOMINAL THREAD LENGTH A NOMINAL MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL THREAD AXIS. 1D AND 1B MODE REPLY11AA05 CWTLD 19POSITIONS,FLOAT AND CONTACT FLOAT AND CONTACT POSITIONS THE RELATIONSHIP BETWEEN THE POSITION OF THE FLOAT AND THE POSITION OF THE CONTACTS. SELECT REPLY CODE 10AF63 CWTMJ 04SIZE ACCOMMODATED,COUPLING,NOMINAL NOMINAL COUPLING SIZE ACCOMMODATED THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL COUPLING SIZE THE ITEM WILL ACCOMMODATE. 1D AND 1B MODE REPLY11AA05 CWTNJ 04DISTANCE BETWEEN FACE EDGE AND BODY END,NOMINAL NOMINAL DISTANCE BETWEEN FACE EDGE AND BODY END NONE. 1D AND 1B MODE REPLY11AA05 CWTPJ /D/A19POSITION,CONTACT,THERMOCOUPLE THERMOCOUPLE CONTACT POSITION A DESIGNATION WHICH SERVES TO IDENTIFY THE POSITION OF THE THERMOCOUPLE CONTACT(S). 2D AND 1A MODE REPLY21AP551AP56 CWTQJ /D/ 04DIAMETER,BUTTON BUTTON DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BUTTON,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY23AJ401AC20 CWTRL 16STYLE DESIGNATOR,HUB HUB STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HUB. 1L MODE REPLY 0 CWTSJ 10FLOW RATE,WATER WATER FLOW RATE THE RATED CAPACITY OF WATER FLOW MOVED THROUGH THE ITEM. 1D AND 1B MODE REPLY12AG67 CWTTB /D/ 13THREAD PITCH IN MILLIMETERS,SCREW,FACILITY,CONNECTION CONNECTION FACILITY SCREW THREAD PITCH IN MILLIMETERS A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS OF THE CONNECTION FACILITY MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CWTWJ /D/A13THREAD TOLERANCE CLASS,SHAFT SHAFT THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND SHAFT GRADE. 1D AND 1A MODE REPLY13AN73 CWTXJ 04DIAMETER,NOMINAL,HUB HUB NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HUB,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWTYB /D/ 13THREAD PITCH IN MILLIMETERS,SHAFT SHAFT THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE SHAFT THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CWTZJ /D/A13THREAD TOLERANCE CLASS,INTERNAL,HEAD HEAD INTERNAL THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE. 1D AND 1A MODE REPLY13AN73 CWWBB 10TIME,RECOVERY,BATTERY BATTERY RECOVERY TIME THE TIME REQUIRED TO CHARGE A BATTERY(IES) TO ITS RATED CAPACITY AFTER A PERIOD OF DISCHARGE. 1B MODE REPLY 0 CWWCJ 04LENGTH,NOMINAL,SURFACE,CLAMPING CLAMPING SURFACE NOMINAL LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF A CLAMPING SURFACE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CWWDJ 04RADIUS,CORNER,SIDE SIDE CORNER RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CWWFJ 04RADIUS,OUTSIDE,NOMINAL NOMINAL OUTSIDE RADIUS NONE. 1D AND 1B MODE REPLY11AA05 CWWGJ /D/ 04HEIGHT HEIGHT PLEASE USE MRC HGTH IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 CWWHJ 04LENGTH,NOMINAL,END END NOMINAL LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE END OF THE ITEM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CWWJA 10COMPATIBILITY,PROGRAM PROGRAM COMPATIBILITY THE PROGRAM(S) FOR WHICH THE POWER SUPPLY IS DESIGN COMPATIBLE. 1A MODE REPLY 0 CWWKD 19CLASSIFICATION,PRECISION PRECISION CLASSIFICATION THE QUALITY DESIGNATION OF AN ITEM AS DETERMINED BY INDUSTRY,ASSOCIATION,OR MANUFACTURER STANDARDS. SELECT REPLY CODE 10AP71 CWWLB 13THREAD PITCH IN MILLIMETERS,INTERNAL INTERNAL THREAD PITCH IN MILLIMETERS A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT INTERNAL THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CWWMJ 04DIAMETER,HOLE,CLAMPING CLAMPING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CLAMPING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CWWNJ 04DIAMETER,NOMINAL,END END NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE END OF THE ITEM,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWWPJ 04RADIUS,SIDE SIDE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CWWQJ /D/ 04DEPTH,GROOVE,INTERNAL INTERNAL GROOVE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWWRA 13THREAD CLASS,INTERNAL INTERNAL THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE OF AN INTERNAL THREAD. 1A MODE REPLY 0 CWWSJ 04LENGTH,NOMINAL,STEP,FIRST FIRST STEP NOMINAL LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE FIRST STEP,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CWWTJ 04DIAMETER,GAGE GAGE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWWWJ /D/ 04DIAMETER,FACE,RAISED,SECOND DISCHARGE FLANGE SECOND DISCHARGE FLANGE RAISED FACE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWWXJ /D/ 04LENGTH,GAGE GAGE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWWYB 19LINE,EFFICIENCY,POWER SUPPLY POWER SUPPLY EFFICIENCY LINE THE POWER SUPPLY OPERATIONAL EFFICIENCY WHEN CONNECTED TO AN ALTERNATE CURRENT POWER LINE. 1B MODE REPLY 0 CWWZB 19BATTERY,EFFICIENCY,POWER SUPPLY POWER SUPPLY EFFICIENCY BATTERY THE POWER SUPPLY OPERATIONAL EFFICIENCY WHEN CONNECTED TO A BATTERY(IES). 1B MODE REPLY 0 CWXBJ 04DIAMETER,NOMINAL,STEP,FIRST FIRST STEP NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FIRST STEP,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWXCJ 04DISTANCE FROM END TO FIRST MOUNTING HOLE CENTER DISTANCE FROM END TO FIRST MOUNTING HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWXDJ 04LENGTH,NOMINAL,ARC ARC NOMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CWXFD /D/ 19WARRANTY,PERFORMANCE,EXTENDED EXTENDED PERFORMANCE WARRANTY AN INDICATION THAT AN EXTENDED PERFORMANCE WARRANTY HAS BEEN ESTABLISHED FOR AN ITEM OF SUPPLY BETWEEN THE UNITED STATES GOVERNMENT AND THE ORIGINAL EQUIPMENT MANUFACTURER AND/OR SUPPLIER. SELECT REPLY CODE 10AA61 CWXGJ 04LENGTH,NOMINAL,STEP,SECOND SECOND STEP NOMINAL LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE SECOND STEP,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CWXHJ /D/ 04WIDTH,OPENING,HOOK,UPPER UPPER HOOK OPENING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWXJA 12QUANTITY,SECTION SECTION QUANTITY THE NUMBER OF SECTIONS REQUIRED TO MAKE THE ITEM. 1A MODE REPLY 0 CWXKJ 10WEIGHT,DETERMINING,SHAFT RADIAL PLAY SHAFT RADIAL PLAY DETERMINING WEIGHT THE FORCE (LOAD) APPLIED PERPENDICULAR TO THE SHAFT AXIS TO DETERMINE RADIAL PLAY. 1D AND 1B MODE REPLY12AG67 CWXLJ 04DIAMETER,NOMINAL,STEP,SECOND SECOND STEP NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SECOND STEP,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWXMJ 04WIDTH,OUTSIDE,EYE EYE OUTSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWXNJ 04DISTANCE FROM END TO FIRST CLAMPING HOLE CENTER DISTANCE FROM END TO FIRST CLAMPING HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 CWXPJ 04LENGTH,NOMINAL,STEP,THIRD THIRD STEP NOMINAL LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE THIRD STEP,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CWXQJ 04WIDTH,NECK NECK WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE NECK,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CWXRJ /D/ 04WIDTH,OPENING,HOOK,LOWER LOWER HOOK OPENING WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWXSL 16STYLE,INSERT INSERT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE INSERT. 1L MODE REPLY 0 CWXTJ 04DIAMETER,NOMINAL,STEP,THIRD THIRD STEP NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THIRD STEP,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWXWJ A18TYPE AND QUANTITY ACCOMMODATED,CIRCUIT BREAKER CIRCUIT BREAKER TYPE AND QUANTITY ACCOMMODATED INDICATES THE TYPE AND NUMBER OF CIRCUIT BREAKERS THE ITEM CAN ACCOMMODATE 1D AND 1A MODE REPLY12AC82 CWXXJ 04DIAMETER,LARGEST,NECK NECK LARGEST DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST PORTION OF THE NECK,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CWXYJ 04WIDTH,NOMINAL,GROOVE,FIRST FIRST GROOVE NOMINAL WIDTH A NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FIRST GROOVE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CWXZJ 04DISTANCE BETWEEN FIRST AND SECOND CLAMPING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FIRST AND SECOND CLAMPING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 CWYBD 14SHAPE,SHOULDER SHOULDER SHAPE THE PHYSICAL CONFIGURATION OF THE UNTHREADED PORTION OF A BODY ADJACENT TO THE HEAD WHICH IS LARGER THAN THE DIAMETER OF THE SHANK. SELECT REPLY CODE 10AK54 CWYCJ 04DISTANCE BETWEEN FIRST AND THIRD CLAMPING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FIRST AND THIRD CLAMPING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 CWYDJ 04DIAMETER,NOMINAL,GROOVE,FIRST FIRST GROOVE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FIRST GROOVE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWYFJ 10WEIGHT,DETERMINING,SHAFT END PLAY SHAFT END PLAY DETERMINING WEIGHT THE FORCE (LOAD) APPLIED PARALLEL TO THE SHAFT AXIS TO DETERMINE END PLAY. 1D AND 1B MODE REPLY12AG67 CWYGJ T13THREAD PITCH DIAMETER,INTERNAL,NONSTANDARD NONSTANDARD INTERNAL THREAD PITCH DIAMETER THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A NONSTANDARD INTERNAL STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 CWYHJ 04DISTANCE BETWEEN FIRST AND FOURTH CLAMPING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FIRST AND FOURTH CLAMPING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 CWYJA 13THREAD CLASS,DISCHARGE,SECOND SECOND DISCHARGE THREAD CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD. 1A MODE REPLY 0 CWYKJ /D/A18TYPE AND QUANTITY,CONTACT,ACCOMMODATED ACCOMMODATED CONTACT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF CONTACTS ACCOMMODATED BY THE ITEM. 3D AND 1A MODE REPLY31AP551AP562AG81 CWYLJ 04DISTANCE FROM END TO FIRST GROOVE,NOMINAL NOMINAL DISTANCE FROM END TO FIRST GROOVE THE NOMINAL DISTANCE FROM THE END OF THE ITEM TO THE FIRST GROOVE. 1D AND 1B MODE REPLY11AA05 CWYMJ 04DISTANCE BETWEEN FIRST AND FIFTH CLAMPING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FIRST AND FIFTH CLAMPING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 CWYNJ 04DIAMETER,NOMINAL,PILOT PILOT NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CWYPJ 04DIAMETER,HOLE HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CWYQJ /D/A19NUMBER,TYPE,ITEM,TYPE DESIGNATION SYSTEM TYPE DESIGNATION SYSTEM ITEM TYPE NUMBER THE TYPE NUMBER ASSIGNED TO THE ITEM AND THE TYPE DESIGNATION SYSTEM. 1D AND 1A MODE REPLY13AJ50 CWYRJ 04WIDTH,NOMINAL,GROOVE,SECOND SECOND GROOVE NOMINAL WIDTH A NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SECOND GROOVE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CWYSJ 04DISTANCE BETWEEN FIRST AND SIXTH CLAMPING HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FIRST AND SIXTH CLAMPING HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 CWYTD 19STATE OF REFRIGERATION STATE OF REFRIGERATION A MECHANICALLY CONTROLLED ENVIRONMENT THAT CHILLS OR FREEZES ITEMS TO PRESERVE FRESHNESS. SELECT REPLY CODE 10AE98 CWYWJ 04DIAMETER,NOMINAL,GROOVE,SECOND SECOND GROOVE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SECOND GROOVE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWYXJ /D/ 10VOLTAGE RATING AND TYPE VOLTAGE RATING AND TYPE INDICATES THE TYPE OF VOLTAGE AND THE RATED VALUE FOR WHICH THE ITEM IS DESIGNED. 3D AND 1B MODE REPLY31AB631AC202AN87 CWYYJ 04DIAMETER,ENTRANCE ENTRANCE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ENTRANCE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWYZJ 04DISTANCE BETWEEN MOUNTING SUPPORT AND NEAREST TERMINAL,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING SUPPORT AND NEAREST TERMINAL NONE. 2D AND 1B MODE REPLY21AA051AC20 CWZBA 12QUANTITY,LINE,SAMPLING SAMPLING LINE QUANTITY THE NUMBER OF SAMPLING LINES PROVIDED. 1A MODE REPLY 0 CWZCJ 04DISTANCE FROM END TO SECOND GROOVE,NOMINAL NOMINAL DISTANCE FROM END TO SECOND GROOVE THE NOMINAL DISTANCE FROM THE END OF THE ITEM TO THE SECOND GROOVE. 1D AND 1B MODE REPLY11AA05 CWZDA /D/ 03DESIGNATION AND SIZE ACCOMMODATED,TRADE,CONDUIT CONDUIT TRADE DESIGNATION AND SIZE ACCOMMODATED THE ALPHA-NUMERIC DESIGNATION AND SIZE OF THE CONDUIT ACCOMMODATED. 1A MODE REPLY 0 CWZFD /D/ 18TYPE,PAINT PAINT TYPE INDICATES THE TYPE OF PAINT. SELECT REPLY CODE 10AJ06 CWZGJ 04WIDTH,KEY,PEENING PEENING KEY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CWZHD 11METHOD,TUNING,FREQUENCY FREQUENCY TUNING METHOD THE MEANS OF TUNING THE FREQUENCY OF THE ITEM. SELECT REPLY CODE 10AL41 CWZJA 12QUANTITY,ITEM,SUPPORTED SUPPORTED ITEM QUANTITY THE NUMBER OF ITEMS TO BE SUPPORTED. 1A MODE REPLY 0 CWZKJ 04DIAMETER,NOMINAL,HOLE,MOUNTING MOUNTING HOLE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWZLJ /D/ 04LENGTH,LINE,SAMPLING SAMPLING LINE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION FROM THE INPUT COUPLING TO THE OUTPUT COUPLING,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CWZMJ 10TIME,DRYING,RATED RATED DRYING TIME THE TIME REQUIRED FOR THE ITEM TO DRY. 2D AND 1B MODE REPLY22AG671AC20 CWZNJ 04DIAMETER,NOMINAL,CIRCLE,BOLT HOLE BOLT HOLE CIRCLE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT HOLE CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CWZPJ 04ANGLE FROM CENTER LINE TO CENTER OF FIRST KEYWAY ANGLE FROM CENTER LINE TO CENTER OF FIRST KEYWAY NONE. 2D AND 1B MODE REPLY21AP381AC20 CWZQJ 10RANGE,FREQUENCY,TUNABLE TUNABLE FREQUENCY RANGE THE MINIMUM AND MAXIMUM FREQUENCY TO WHICH THE ITEM CAN BE TUNED. 2D AND 1B MODE REPLY21AE061AB56 CWZRJ 04SIZE,VALVE,BUTTERFLY BUTTERFLY VALVE SIZE DESIGNATES THE SIZE OF THE BUTTERFLY VALVE. 1D AND 1B MODE REPLY11AA05 CWZSJ 04DISTANCE FROM END TO FIRST MOUNTING HOLE CENTER,NOMINAL NOMINAL DISTANCE FROM END TO FIRST MOUNTING HOLE CENTER THE NOMINAL DISTANCE FROM THE END OF THE ITEM TO THE CENTER OF THE FIRST MOUNTING HOLE. 1D AND 1B MODE REPLY11AA05 CWZTA 19NUMBER,CHIP,COLOR COLOR CHIP NUMBER A NUMBER ASSIGNED TO A PARTICULAR GRADATION OF A COLOR IN ACCORDANCE WITH FEDERAL STANDARD 595 FOR PURPOSES OF READY IDENTIFICATION. 1A MODE REPLY 0 CWZWJ /D/ 10MASS,SPECIFIC SPECIFIC MASS THE SPECIFIC MASS OF THE ITEM. 2D AND 1B MODE REPLY22AG671AC20 CWZXJ /D/ 04DIAMETER,INSIDE,END,LOOP LOOP END INSIDE DIAMETER THE LENGTH OF A STRIAGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LOOP END,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CWZYD 18TYPE,CHAMBER,ENVIRONMENTAL ENVIRONMENTAL CHAMBER TYPE INDICATES THE TYPE OF ENVIRONMENTAL CHAMBER. SELECT REPLY CODE 10AL05 CWZZJ 04DISTANCE BETWEEN MOUNTING HOLES,NOMINAL,CENTER TO CENTER CENTER TO CENTER NOMINAL DISTANCE BETWEEN MOUNTING HOLES THE NOMINAL DISTANCE BETWEEN THE CENTER OF A MOUNTING HOLE AND THE CENTER OF AN ADJACENT MOUNTING HOLE. 1D AND 1B MODE REPLY11AA05 CXBBJ 04DISTANCE,CENTER TO CENTER,WAVEGUIDE WAVEGUIDE CENTER TO CENTER DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CXBCJ /D/ 10FREQUENCY RATING,MAXIMUM,CONTACT CONTACT MAXIMUM FREQUENCY RATING THE MAXIMUM FREQUENCY AT WHICH THE CONTACT IS RATED. 3D AND 1B MODE REPLY31AP551AP561AE06 CXBDJ 04HEIGHT,WAVEGUIDE WAVEGUIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CXBFJ 04DIAMETER,OUTLET,MAIN TRUNK REDUCING MAIN TRUNK REDUCING OUTLET DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXBGJ 04LENGTH,LEG,FOURTH,WAVEGUIDE WAVEGUIDE FOURTH LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXBHJ 04WIDTH,OVERALL,ADAPTER ADAPTER OVERALL WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXBJJ 04DIAMETER,OUTSIDE,SEAL SEAL OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXBKJ 04WIDTH,OUTSIDE,SEAL SEAL OUTSIDE WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXBLJ 04THICKNESS,VANE VANE THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CXBMJ 04DIAMETER,RECESS,FIRST INTAKE FLANGE FIRST INTAKE FLANGE RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXBNJ 04DIAMETER,CIRCLE,OUTER TERMINAL OUTER TERMINAL CIRCLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTER TERMINAL CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXBPJ 04DISTANCE BETWEEN LUGS,END,FIRST FIRST END DISTANCE BETWEEN LUGS THE DISTANCE BETWEEN THE LUGS OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CXBQJ 04LENGTH,PROJECTION,END,INNER INNER END PROJECTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXBRB /D/ 13THREAD PITCH IN MILLIMETERS,OUTLET OUTLET THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT OUTLET THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CXBSJ 04DISTANCE FROM MOUNTING HOLE CENTER TO BOTTOM,NOMINAL NOMINAL DISTANCE FROM MOUNTING HOLE CENTER TO BOTTOM THE NOMINAL DISTANCE FROM THE CENTER OF A MOUNTING HOLE TO THE BOTTOM OF THE ITEM. 1D AND 1B MODE REPLY11AA05 CXBTB 10VOLTAGE RATING PER MILLIMETER THICKNESS IN KILOVOLTS,DIELECTRIC MATERIAL DIELECTRIC MATERIAL VOLTAGE RATING PER MILLIMETER THICKNESS IN KILOVOLTS THE MAXIMUM POTENTIAL GRADIENT THAT THE INSULATING MATERIAL CAN WITHSTAND PER MILLIMETER THICKNESS WITHOUT RUPTURE. 1B MODE REPLY 0 CXBWD 13THREAD SERIES DESIGNATOR,CONNECTION,INTAKE INTAKE CONNECTION THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CXBXJ 04SIZE FOR WHICH DESIGNED,VALVE VALVE SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE VALVE FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY11AA05 CXBYD 11METHOD,GENERATING,VACUUM VACUUM GENERATING METHOD THE MEANS BY WHICH THE VACUUM IS GENERATED. SELECT REPLY CODE 10AE36 CXBZJ /D/A13THREAD TOLERANCE CLASS,INTAKE,SECOND SECOND INTAKE THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE. 1D AND 1A MODE REPLY13AN73 CXCBD 05DIRECTION,DISCHARGE DISCHARGE DIRECTION THE DIRECTION IN WHICH THE ITEM DISCHARGES DURING OPERATION. SELECT REPLY CODE 10AJ69 CXCCJ A13THREAD TOLERANCE CLASS,INTAKE,FIRST FIRST INTAKE THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE. 1D AND 1A MODE REPLY13AN73 CXCDJ 13THREAD SIZE,NOMINAL,CONNECTION,INTAKE INTAKE CONNECTION NOMINAL THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE INTAKE CONNECTION. 1D AND 1B MODE REPLY11AA05 CXCFJ 04THICKNESS,END,SECOND SECOND END THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CXCGA 12QUANTITY,CONTACT,INCLUDED INCLUDED CONTACT QUANTITY THE NUMBER OF CONTACTS INCLUDED WITH THE ITEM WHICH PROVIDES ELECTRICAL CONNECTION. 1A MODE REPLY 0 CXCHJ /D/T13THREAD PITCH DIAMETERS,CONNECTION,INTAKE INTAKE CONNECTION THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 CXCJD 14SHAPE,HOLE,ACCOMMODATION,BUSHING BUSHING ACCOMMODATION HOLE SHAPE THE PHYSICAL CONFIGURATION OF THE HOLE DESIGNED TO ACCOMMODATE A BUSHING. SELECT REPLY CODE 10AK54 CXCKJ A18TYPE AND QUANTITY,COMPONENT COMPONENT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF COMPONENTS WHICH MAKE UP THE ASSEMBLY OR SUBASSEMBLY. 1D AND 1A MODE REPLY13AK95 CXCLD 18TYPE,CONTACT,INCLUDED INCLUDED CONTACT TYPE INDICATES THE TYPE OF CONTACT(S) INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AG81 CXCMB 13THREAD PITCH IN MILLIMETERS,CONNECTION,INTAKE INTAKE CONNECTION THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CXCNJ A19ITEM,SUPPLY SUPPLY ITEM A COMPONENT AS INDICATED BY AN ITEM AND A NATIONAL STOCK NUMBER. 1D AND 1A MODE REPLY13AK95 CXCPA /D/ 19POSITION,CONTACT,MISSING MISSING CONTACT POSITION AN INDICATION OF THE POSITION OF THE MISSING CONTACT(S). 1A MODE REPLY 0 CXCQD 19FIELD OF INDICATION FIELD OF INDICATION THE FIELD OF INDICATION WHICH APPLIES TO THE DIAGNOSIS. SELECT REPLY CODE 10AP73 CXCRD /D/ 13THREAD DIRECTION,CONNECTION,INTAKE INTAKE CONNECTION THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 CXCSJ A19ITEM,NONSUPPLY NONSUPPLY ITEM A COMPONENT,OUTSIDE THE SCOPE OF AN ITEM OF SUPPLY TO BE CATALOGED,AS INDICATED BY AN ITEM NAME,THE NAME OF THE MANUFACTURER AND THE PART NUMBER OF THE ITEM AS IDENTIFIED BY THE MANUFACTURER. 1D AND 1A MODE REPLY13AK95 CXCTJ 04DIAMETER ACCOMMODATED,OPTICAL FIBER OPTICAL FIBER DIAMETER ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE OPTICAL FIBER,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CXCWD 19FORM,CONDUCTOR CONDUCTOR FORM THE FABRICATED FORM OF THE CONDUCTOR. SELECT REPLY CODE 10AF31 CXCXJ 04DISTANCE BETWEEN MOUNTING HOLES ALONG SIDE OF A SQUARE,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES ALONG SIDE OF A SQUARE NONE. 2D AND 1B MODE REPLY21AA051AC20 CXCYG 19NAME ASSIGNED BY CONTROLLING AGENCY,PART PART NAME ASSIGNED BY CONTROLLING AGENCY THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM. FULL TEXT WRITE-IN 0 CXCZJ /D/A13THREAD TOLERANCE CLASS,CONNECTION,INTAKE INTAKE CONNECTION THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE. 1D AND 1A MODE REPLY13AN73 CXDBJ A18TYPE AND QUANTITY,CONTACT,MISSING MISSING CONTACT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF CONTACTS THAT CAN BE ACCOMMODATED BUT ARE NOT INCLUDED WITH THE ITEM. 1D AND 1A MODE REPLY12AG81 CXDCJ A04SIZE,CONDUCTOR,ROUND ROUND CONDUCTOR SIZE THE DESIGNATION USED TO DESCRIBE THE ROUND STRANDED OR ROUND SOLID CONDUCTOR SIZE. 1D AND 1A MODE REPLY11AA44 CXDDJ 04TAPER,END,SECOND SECOND END TAPER NONE. 1D AND 1B MODE REPLY11AB39 CXDFD 18TYPE,BEAM SPLITTER BEAM SPLITTER TYPE INDICATES THE TYPE OF BEAM SPLITTER. SELECT REPLY CODE 10AJ12 CXDGA 04SIZE PER CONDUCTOR,AWG,STRAND STRAND AWG SIZE PER CONDUCTOR THE AMERICAN WIRE GAGE SIZE OF THE INDIVIDUAL STRANDS OF WIRE USED IN EACH STRANDED CONDUCTOR. 1A MODE REPLY 0 CXDHD 13THREAD SERIES DESIGNATOR,CONNECTION,DISCHARGE DISCHARGE CONNECTION THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 CXDJD /D/ 09MATERIAL,LINING,FRICTION FRICTION LINING MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE FRICTION LINING IS FABRICATED. SELECT REPLY CODE 10MA01 CXDKJ 04DIAMETER,OUTSIDE,SURFACE,RAISED,FIRST FIRST RAISED SURFACE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXDLA 10PERCENTAGE RATIO,REFLECTANCE/TRANSMITTANCE REFLECTANCE/TRANSMITTANCE PERCENTAGE RATIO THE PERCENTAGE RATIO OF LIGHT REFLECTED AND TRANSMITTED. 1A MODE REPLY 0 CXDMD 14SHAPE,CROSS-SECTIONAL,CONDUCTOR CONDUCTOR CROSS-SECTIONAL SHAPE THE GEOMETRIC CONFIGURATION OF THE CONDUCTOR WHEN VIEWED IN CROSS-SECTION. SELECT REPLY CODE 10AL59 CXDNJ 04DIAMETER,RECESS,FIRST DISCHARGE FLANGE FIRST DISCHARGE FLANGE RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXDPJ 04HEIGHT,SURFACE TO FLANGE,RAISED RAISED SURFACE TO FLANGE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CXDQJ A19ARRANGEMENT AND QUANTITY,CONDUCTOR CONDUCTOR ARRANGEMENT AND QUANTITY THE ARRANGEMENT AND NUMBER OF ARRANGEMENTS OF THE CONDUCTORS. 1D AND 1A MODE REPLY12AK80 CXDRJ 13THREAD SIZE,NOMINAL,CONNECTION,DISCHARGE DISCHARGE CONNECTION NOMINAL THREAD SIZE DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE DISCHARGE CONNECTION. 1D AND 1B MODE REPLY11AA05 CXDSJ /D/ 04HEIGHT,SURFACE,RAISED,FIRST FIRST RAISED SURFACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CXDTA 12QUANTITY,GROUP GROUP QUANTITY THE NUMBER OF GROUPS INTO WHICH TWO OR MORE CONDUCTORS ARE ARRANGED. 1A MODE REPLY 0 CXDWJ /D/ 04HEIGHT,SURFACE,RAISED,SECOND SECOND RAISED SURFACE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CXDXJ /D/ 10AREA,EFFECTIVE,STROKE STROKE EFFECTIVE AREA A MEASUREMENT OF THE EFFECTIVE AREA OF THE STROKE. 1D AND 1B MODE REPLY12AG67 CXDYJ A18TYPE AND QUANTITY,ARRANGEMENT,CONDUCTOR GROUPING CONDUCTOR GROUPING ARRANGEMENT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF CONDUCTOR ARRANGEMENTS WITHIN GROUPS. 1D AND 1A MODE REPLY12AK80 CXDZJ 04LENGTH,EXTENDED,NOMINAL NOMINAL EXTENDED LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM WHEN IN AN EXTENDED POSITION,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CXFBJ /D/T13THREAD PITCH DIAMETERS,CONNECTION,DISCHARGE DISCHARGE CONNECTION THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 CXFCJ 04DIAMETER,OUTSIDE,SURFACE,RAISED,SECOND SECOND RAISED SURFACE OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXFDJ 04DIAMETER,COUNTERBORE,THIRD THIRD COUNTERBORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXFFH /D/ 09MATERIAL,CONTACT CONTACT MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE CONTACT(S) IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. 3D MODE REPLY 31AP551AP566AD09 CXFGD 19SEQUENCE WITHIN GROUPS,CONDUCTOR CONDUCTOR SEQUENCE WITHIN GROUPS THE IDENTIFICATION OF THE CONDUCTORS WITHIN A GROUP. SELECT REPLY CODE 10AJ91 CXFHJ /D/ 04DIAMETER,RECESS,SECOND INTAKE FLANGE SECOND INTAKE FLANGE RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXFJB 13THREAD PITCH IN MILLIMETERS,CONNECTION,DISCHARGE DISCHARGE CONNECTION THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CXFKJ 10VOLTAGE RATING VOLTAGE RATING THE MAXIMUM SUSTAINED VOLTAGE THAT CAN BE SAFELY APPLIED TO THE ITEM WITHOUT RISKING FAILURE OR DAMAGE. 1D AND 1B MODE REPLY12AH16 CXFLJ /D/ 04DEPTH,COUNTERBORE,THIRD THIRD COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXFMJ 04SIZE,APERTURE,LUG,TERMINAL TERMINAL LUG APERTURE SIZE DESIGNATES THE SIZE OF THE MOUNTING APERTURE PROVIDED IN THE TERMINAL LUG. 1D AND 1B MODE REPLY11AA05 CXFNJ 04LENGTH,COMPRESSED,NOMINAL NOMINAL COMPRESSED LENGTH A NOMINAL MEASUREMENT OF THE SMALLEST LENGTH TO WHICH THE ITEM MAY BE COMPRESSED,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CXFPJ 04ANGLE,SURFACE,RAISED RAISED SURFACE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CXFQJ /D/ 04DIAMETER,GROOVE,NOMINAL NOMINAL GROOVE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GROOVE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXFRJ /D/ 04WIDTH,GROOVE,NOMINAL NOMINAL GROOVE WIDTH A NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A GROOVE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CXFSA /D/ 10GRAVITY RATING AT 60 DEG FAHRENHEIT,AMERICAN PETROLEUM INSTITUTE AMERICAN PETROLEUM INSTITUTE GRAVITY RATING AT 60 DEG FAHRENHEIT AN INDICATION OF THE DENSITY OF THE ITEM AS SPECIFIED BY THE AMERICAN PETROLEUM INSTITUTE GRAVITY SCALE AT 60 DEGREES FAHRENHEIT. 1A MODE REPLY 0 CXFTD /D/ 07PLANE,MOUNTING SURFACE MOUNTING SURFACE PLANE AN INDICATION OF THE SURFACE PLANE ON WHICH AN ITEM IS DESIGNED TO BE MOUNTED. SELECT REPLY CODE 10AF63 CXFWD 18TYPE,SHIELD,PROTECTIVE PROTECTIVE SHIELD TYPE INDICATES THE TYPE OF SHIELD. SELECT REPLY CODE 10AG94 CXFXJ /D/A13THREAD TOLERANCE CLASS,DISCHARGE,FIRST FIRST DISCHARGE THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE. 1D AND 1A MODE REPLY13AN73 CXFYL 16STYLE,LUG,TERMINAL TERMINAL LUG STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TERMINAL LUG. 1L MODE REPLY 0 CXFZJ /D/ 04DEPTH,GROOVE,NOMINAL NOMINAL GROOVE DEPTH A NOMINAL MEASUREMENT BETWEEN SPECIFIED POINTS OF A GROOVE,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 CXGBD /D/ 13THREAD DIRECTION,CONNECTION,DISCHARGE DISCHARGE CONNECTION THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 CXGCD 19POLARITY,TERMINAL TERMINAL POLARITY THE POLARITY OF THE TERMINAL AS DETERMINED BY THE POLARITY OF THE ACCOMMODATED BATTERY POST. SELECT REPLY CODE 10AK22 CXGDJ /D/ 04DISTANCE TO RAISED SEAT WEAR SURFACE,CLOSED END,NOMINAL NOMINAL CLOSED END DISTANCE TO RAISED SEAT WEAR SURFACE THE NOMINAL CLOSED END DISTANCE TO THE RAISED SEAT WEAR SURFACE. 1D AND 1B MODE REPLY11AA05 CXGFJ /D/ 04WIDTH,SLOT,NOMINAL NOMINAL SLOT WIDTH A NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SLOT,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CXGGA 19NUMBER,REFERENCE,IDENTIFYING,MANUFACTURER,TERMINAL TERMINAL MANUFACTURER IDENTIFYING REFERENCE NUMBER THE IDENTIFYING REFERENCE NUMBER ASSIGNED TO THE TERMINAL(S) BY THE MANUFACTURER. 1A MODE REPLY 0 CXGHJ /D/ 04DEPTH,SOCKET SOCKET DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE SOCKET,IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 CXGJL 16STYLE,STRUT STRUT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE STRUT. 1L MODE REPLY 0 CXGKJ /D/ 04LENGTH,THRU-HOLE,NOMINAL NOMINAL THRU-HOLE LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE THRU-HOLE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CXGLJ /D/A13THREAD TOLERANCE CLASS,CONNECTION,DISCHARGE DISCHARGE CONNECTION THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE. 1D AND 1A MODE REPLY13AN73 CXGMD /D/ 14SHAPE,BLADE BLADE SHAPE THE PHYSICAL CONFIGURATION OF THE BLADE. PLEASE USE MRC CYMR IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AG26 CXGNA 19CODE,COMMERCIAL AND GOVERNMENT ENTITY,TERMINAL TERMINAL COMMERCIAL AND GOVERNMENT ENTITY CODE THE FIVE-POSITION COMMERCIAL AND GOVERNMENT ENTITY CODE FOR THE MANUFACTURER OF THE TERMINAL. 1A MODE REPLY 0 CXGPJ 04DIAMETER,HOLE,NOMINAL NOMINAL HOLE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXGQD /D/ 19MEDIUM,COOLING,BEARING BEARING COOLING MEDIUM THE COOLING MEDIUM USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE BEARINGS. USE MRC ACZV AND ISAC TO TABLE 0094 SELECT REPLY CODE 10AL57 CXGRL 16STYLE,STRAIN RELIEF STRAIN RELIEF STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE METHOD BY WHICH STRESS OR STRAIN IS RELIEVED. 1L MODE REPLY 0 CXGSJ 04LENGTH,BODY,STRUT,NOMINAL NOMINAL STRUT BODY LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE STRUT BODY,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CXGTJ /D/ 04DIAMETER,TAPERED HOLE,MAJOR,NOMINAL NOMINAL MAJOR TAPERED HOLE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST END OF A TAPERED HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXGWJ 04LENGTH,CONDUCTOR,INDIVIDUAL INDIVIDUAL CONDUCTOR LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN INDIVIDUAL CONDUCTOR,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CXGXJ /D/ 04DIAMETER,TAPERED,HOLE,MINOR,NOMINAL NOMINAL MINOR HOLE TAPERED DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST END OF A TAPERED HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXGYJ /D/A13THREAD TOLERANCE CLASS,DISCHARGE,SECOND SECOND DISCHARGE THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE. 1D AND 1A MODE REPLY13AN73 CXGZJ /D/ 04LENGTH,INSIDE PROJECTION,BASE,NOMINAL NOMINAL BASE INSIDE PROJECTION LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE BASE INSIDE PROJECTION,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CXHBJ 04DIAMETER ACCOMMODATED,INSIDE,NOMINAL,HOSE HOSE NOMINAL INSIDE DIAMETER ACCOMMODATED THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOSE THAT THE ITEM IS DESIGNED TO ACCOMMODATE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXHCJ 04LENGTH,BODY,CARTRIDGE,NOMINAL NOMINAL CARTRIDGE BODY LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE CARTRIDGE BODY,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CXHDJ /D/ 04DIAMETER,BASE,OUTSIDE,NOMINAL NOMINAL OUTSIDE BASE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BASE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXHFD 11METHOD,FABRICATION,HOUSING HOUSING FABRICATION METHOD THE PROCESS USED IN MANUFACTURING THE HOUSING. SELECT REPLY CODE 10AB47 CXHGJ /D/ 04THICKNESS,BASE,NOMINAL NOMINAL BASE THICKNESS A NOMINAL MEASUREMENT OF THE SMALLEST DIMENSION OF A BASE,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 CXHHJ 10STRENGTH,PULL,LEAD LEAD PULL STRENGTH THE PULLING FORCE WHICH THE ITEM IS CAPABLE OF WITHSTANDING WITHOUT ANY PERMANENT DEFORMATION OR DAMAGE. 1D AND 1B MODE REPLY12AN75 CXHJL 16STYLE,LEVER LEVER STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LEVER. 1L MODE REPLY 0 CXHKJ /D/T13THREAD PITCH DIAMETERS,INTAKE,FIRST FIRST INTAKE THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 CXHLJ /D/ 04DIAMETER,HOLE,PLAIN,NOMINAL NOMINAL PLAIN HOLE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PLAIN HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXHMJ /D/ 04WIDTH ACCOMMODATED,WHEEL,NOMINAL NOMINAL WHEEL WIDTH ACCOMMODATED A NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE ACCOMMODATION FOR A WHEEL,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CXHND 18TYPE,BEARING,SHAFT SHAFT BEARING TYPE INDICATES THE TYPE OF SHAFT BEARING/S/ FURNISHED. SELECT REPLY CODE 10AH96 CXHPJ 04WIDTH BETWEEN JACKET,INBOARD,FIRST CHAIN LINK FIRST CHAIN LINK INBOARD WIDTH BETWEEN JACKET NONE. 1D AND 1B MODE REPLY11AA05 CXHQJ /D/ 04DIAMETER ACCOMMODATED,WHEEL,NOMINAL NOMINAL WHEEL DIAMETER ACCOMMODATED THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR A WHEEL,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXHRJ /D/ 04WIDTH BETWEEN JACKET,INBOARD,SECOND CHAIN LINK SECOND CHAIN LINK INBOARD WIDTH BETWEEN JACKET NONE. 1D AND 1B MODE REPLY11AA05 CXHSJ /D/ 10AREA,SURFACE,BRAKING,NOMINAL NOMINAL BRAKING SURFACE AREA A NOMINAL MEASUREMENT OF THE AMOUNT OF BRAKING SURFACE AREA. 1D AND 1B MODE REPLY12AG67 CXHTJ 04WIDTH BETWEEN JACKET,INBOARD,LINK LINK INBOARD WIDTH BETWEEN JACKET NONE. 1D AND 1B MODE REPLY11AA05 CXHWD /D/ 09MATERIAL,DIAPHRAGM DIAPHRAGM MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE DIAPHRAGM IS FABRICATED. SELECT REPLY CODE 10MA01 CXHXJ 04HEIGHT,JACKET,FIRST CHAIN LINK FIRST CHAIN LINK JACKET HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 CXHYJ /D/ 04DIAMETER,HOLE,ARM ARM HOLE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXHZJ /D/ 04HEIGHT,JACKET,SECOND CHAIN LINK SECOND CHAIN LINK JACKET HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 CXJBJ /D/ 04DIAMETER,SPLINE,NOMINAL NOMINAL SPLINE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXJCJ 04HEIGHT,JACKET,LINK LINK JACKET HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 CXJDJ /D/T13THREAD PITCH DIAMETERS,DISCHARGE,FIRST FIRST DISCHARGE THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 CXJFJ 04DIAMETER,JACKET,FIRST CHAIN LINK FIRST CHAIN LINK JACKET DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXJGJ 04DISTANCE ALONG LENGTH,CENTER TO CENTER,PERFORATION PERFORATION CENTER TO CENTER DISTANCE ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXJHJ /D/ 04DIAMETER,JACKET,SECOND CHAIN LINK SECOND CHAIN LINK JACKET DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXJJL /D/ 16STYLE,CLEVIS CLEVIS STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CLEVIS. 1L MODE REPLY 0 CXJKJ 04DIAMETER,JACKET,LINK LINK JACKET DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXJLJ /D/ 04DISTANCE BETWEEN SPLINE HOLE AND FIRST CONNECTION HOLE,CENTER TO CENTER,ARM,CONNECTING CONNECTING ARM CENTER TO CENTER DISTANCE BETWEEN SPLINE HOLE AND FIRST CONNECTION HOLE NONE. 1D AND 1B MODE REPLY11AA05 CXJMJ /D/ 04DISTANCE BETWEEN SPLINE HOLE AND SECOND CONNECTION HOLE,CENTER TO CENTER,ARM,CONNECTING CONNECTING ARM CENTER TO CENTER DISTANCE BETWEEN SPLINE HOLE AND SECOND CONNECTION HOLE NONE. 1D AND 1B MODE REPLY11AA05 CXJNJ /D/ 04DISTANCE BETWEEN SPLINE HOLE AND THIRD CONNECTION HOLE,CENTER TO CENTER,ARM,CONNECTING CONNECTING ARM CENTER TO CENTER DISTANCE BETWEEN SPLINE HOLE AND THIRD CONNECTION HOLE NONE. 1D AND 1B MODE REPLY11AA05 CXJPJ 10UNIT,GRADUATION,INDICATOR INDICATOR GRADUATION UNIT THE INCREMENT OF MEASURE REPRESENTED BY THE MARKING(S) ON THE INDICATOR. 1D AND 1B MODE REPLY13AK09 CXJQJ 04HEIGHT,FLAT,SECOND SECOND FLAT HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CXJRJ /D/ 04DIAMETER,SURFACE,BRAKING,NOMINAL NOMINAL BRAKING SURFACE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXJSD 19PRIME MOVER FOR WHICH DESIGNED PRIME MOVER FOR WHICH DESIGNED THE PRIME MOVER THE HOUSING IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AG27 CXJTD 18TYPE,PROCESSING,FILM FILM PROCESSING TYPE INDICATES THE TYPE OF FILM PROCESSING. SELECT REPLY CODE 10AN35 CXJWJ /D/ 04WIDTH,SURFACE,BRAKING,NOMINAL NOMINAL BRAKING SURFACE WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CXJXJ 04DIAMETER,BUSHING,UNTHREADED UNTHREADED BUSHING DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE UNTHREADED BUSHING,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CXJYB 10VOLTAGE RATING PER MILLIMETER THICKNESS IN KILOVOLTS,DIELECTRIC MATERIAL,DRY DRY DIELECTRIC MATERIAL VOLTAGE RATING PER MILLIMETER THICKNESS IN KILOVOLTS THE MAXIMUM POTENTIAL GRADIENT THAT A DRY INSULATING MATERIAL CAN WITHSTAND PER MILLIMETER THICKNESS WITHOUT RUPTURE. 1B MODE REPLY 0 CXJZJ 04DIAMETER,HOLE,CENTER,NOMINAL NOMINAL CENTER HOLE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CENTER HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXKBJ /D/T13THREAD PITCH DIAMETERS,INTAKE,SECOND SECOND INTAKE THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 CXKCJ 13THREAD SIZE,CONNECTION,NOMINAL,PISTON END PISTON END NOMINAL CONNECTION THREAD SIZE NONE. 1D AND 1B MODE REPLY11AA05 CXKDJ /D/ 04DIAMETER,MAJOR,SPLINE SPLINE MAJOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXKFJ 04DISTANCE ALONG WIDTH,CENTER TO CENTER,PERFORATION PERFORATION CENTER TO CENTER DISTANCE ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXKGJ 04DISTANCE,CENTER TO CENTER,HOLE,NOMINAL,PISTON END PISTON END NOMINAL HOLE CENTER TO CENTER DISTANCE NONE. 1D AND 1B MODE REPLY11AA05 CXKHL 16STYLE DESIGNATOR,BUCKLE BUCKLE STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BUCKLE. 1L MODE REPLY 0 CXKJD 09MATERIAL,IMPREGNATION IMPREGNATION MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE WITH WHICH THE ITEM IS SATURATED. SELECT REPLY CODE 10AG62 CXKKJ 04LENGTH,OVERALL,NOMINAL,PISTON END PISTON END NOMINAL OVERALL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CXKLJ /D/ 04DIAMETER FOR WHICH DESIGNED,DRUM,NOMINAL NOMINAL DRUM DIAMETER FOR WHICH DESIGNED THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DRUM FOR WHICH THE ITEM IS DESIGNED,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXKMJ /D/ 04WIDTH,INSIDE,NOMINAL,END END NOMINAL INSIDE WIDTH A NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE INSIDE LENGTH OF THE END OF THE ITEM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CXKNJ 04DIAMETER,HOLE,BOLT,NOMINAL,PISTON END PISTON END NOMINAL BOLT HOLE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXKPJ /D/ 04DIAMETER,MINOR,SPLINE SPLINE MINOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXKQJ /D/ 04WIDTH FOR WHICH DESIGNED,DRUM,NOMINAL NOMINAL DRUM WIDTH FOR WHICH DESIGNED A NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE DRUM FOR WHICH THE ITEM IS DESIGNED,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CXKRJ A10RATE,SIGNAL SIGNAL RATE THE FREQUENCY OF AUDIBLE SIGNALS. 1D AND 1A MODE REPLY13AJ40 CXKSJ 04DIAMETER,INSIDE,NOMINAL,PISTON END PISTON END NOMINAL INSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXKTJ A12QUANTITY,HOLE HOLE QUANTITY NONE. 1D AND 1A MODE REPLY12AG67 CXKWJ /D/ 04LENGTH,INSIDE,NOMINAL,END END NOMINAL INSIDE LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE INSIDE OF THE END OF THE ITEM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CXKXL 16STYLE DESIGNATOR,CLIP,END END CLIP STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END CLIP. 1L MODE REPLY 0 CXKYJ 04DIAMETER,INSIDE,LARGEST,NOMINAL,PISTON END PISTON END NOMINAL LARGEST INSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXKZJ 04WIDTH,BODY BODY WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXLBJ 04DIAMETER,OUTSIDE,NOMINAL,PISTON END PISTON END NOMINAL OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXLCL 16STYLE DESIGNATOR,BARREL,GROMMET GROMMET BARREL STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE GROMMET BARREL. 1L MODE REPLY 0 CXLDJ /D/ 04WIDTH,KEYWAY KEYWAY WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CXLFJ 04THICKNESS,NOMINAL,PISTON END PISTON END NOMINAL THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 CXLGJ /D/ 04DIAMETER,INSIDE,NOMINAL,END END NOMINAL INSIDE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE INSIDE OF THE END OF THE ITEM,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXLHJ 04LENGTH,ROD,PUSH PUSH ROD LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE PUSH ROD, IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CXLJA /D/ 13THREAD QUANTITY PER INCH,COUPLING COUPLING THREAD QUANTITY PER INCH THE NUMBER OF COUPLING THREADS PER LINEAR INCH ON A LINE PARALLEL TO THE THREAD AXIS. 1A MODE REPLY 0 CXLKJ 04HEIGHT,INSIDE,FITTING FITTING INSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CXLLJ /D/ 04DIAMETER,RECESS,SECOND DISCHARGE FLANGE SECOND DISCHARGE FLANGE RECESS DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXLMJ 04WIDTH,NOMINAL,PISTON END PISTON END NOMINAL WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CXLNJ /D/ 04DIAMETER,NOMINAL,WIRE WIRE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A WIRE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXLPB /D/ 13THREAD PITCH IN MILLIMETERS,COUPLING COUPLING THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT COUPLING THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CXLQJ /D/ 04DISTANCE BETWEEN STUD CENTERS DISTANCE BETWEEN STUD CENTERS NONE. 1D AND 1B MODE REPLY11AA05 CXLRJ 04DEPTH,FORK,NOMINAL,PISTON END PISTON END NOMINAL FORK DEPTH NONE. 1D AND 1B MODE REPLY11AA05 CXLSL 16STYLE DESIGNATOR,FLANGE,GROMMET GROMMET FLANGE STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE GROMMET FLANGE. 1L MODE REPLY 0 CXLTJ /D/ 04LENGTH,FACILITY,MOUNTING MOUNTING FACILITY LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CXLWJ /D/ 04DIAMETER,NOMINAL,PERFORATION PERFORATION NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PERFORATION,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXLXJ 04THICKNESS,ARM,FORK,NOMINAL,PISTON END PISTON END NOMINAL FORK ARM THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 CXLYJ /D/ 13THREAD DIAMETER,STEM SOCKET STEM SOCKET THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF A STEM SOCKET,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CXLZJ /D/A13THREAD TOLERANCE CLASS,COUPLING COUPLING THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE OF A COUPLING THREAD. 1D AND 1A MODE REPLY13AN73 CXMBJ 04THICKNESS,ARM,FORK,RIGHT,NOMINAL,PISTON END PISTON END NOMINAL RIGHT FORK ARM THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 CXMCL 16STYLE DESIGNATOR,WASHER,GROMMET GROMMET WASHER STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE GROMMET WASHER. 1L MODE REPLY 0 CXMDJ /D/ 04WIDTH,SPAN,FORK FORK SPAN WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CXMFJ 04WIDTH,SPAN,FORK,NOMINAL,PISTON END PISTON END NOMINAL FORK SPAN WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CXMGL 16STYLE,COUPLING COUPLING STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE COUPLING. 1L MODE REPLY 0 CXMHJ /D/ 04DISTANCE FROM PINHOLE CENTER TO ROD CONNECTION END DISTANCE FROM PINHOLE CENTER TO ROD CONNECTION END NONE. 1D AND 1B MODE REPLY11AA05 CXMJA 12QUANTITY,DEVICE,LOCKING,COUPLING COUPLING LOCKING DEVICE QUANTITY THE NUMBER OF LOCKING DEVICES ON THE COUPLING. 1A MODE REPLY 0 CXMKJ 04LENGTH,SHANK,NOMINAL,PISTON END PISTON END NOMINAL SHANK LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CXMLJ /D/T13THREAD PITCH DIAMETERS,COUPLING COUPLING THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A COUPLING STRAIGHT SCREW THREAD. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1D AND 1F MODE REPLY11AA05 CXMMJ /D/T13THREAD PITCH DIAMETERS,DISCHARGE,SECOND SECOND DISCHARGE THREAD PITCH DIAMETERS THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD. 1D AND 1F MODE REPLY11AA05 CXMNA 10TIME,SWITCHING,BATTERY BATTERY SWITCHING TIME THE TIME REQUIRED FOR A BATTERY POWER SUPPLY TO SWITCH FROM STANDBY MODE TO FULL RATED OUTPUT POWER. 1A MODE REPLY 0 CXMPB /D/ 13THREAD PITCH IN MILLIMETERS,STEM SOCKET STEM SOCKET THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CXMQD /D/ 13THREAD SERIES DESIGNATOR,COUPLING COUPLING THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR THE SPECIFIC DIAMETER OF A COUPLING. SELECT REPLY CODE 10AH06 CXMRJ 04DIAMETER,SHANK,NOMINAL,PISTON END PISTON END NOMINAL SHANK DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXMSD 18TYPE,PLATE,MOUNTING MOUNTING PLATE TYPE INDICATES THE TYPE OF MOUNTING PLATE. SELECT REPLY CODE 10AK41 CXMTJ 10PRESSURE,OPERATING,EXTERNAL EXTERNAL OPERATING PRESSURE THE NOMINAL FORCE PER UNIT OF AREA EXERTED INWARD FOR WHICH THE ITEM IS DESIGNED. 1D AND 1B MODE REPLY12AG67 CXMWJ /D/ 04DIAMETER,HOLE,PIVOT PIN PIVOT PIN HOLE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXMXB 10TIME,OPERATING,EMERGENCY,POWER SUPPLY,BATTERY BATTERY POWER SUPPLY EMERGENCY OPERATING TIME THE EMERGENCY OPERATING TIME A BATTERY POWER SUPPLY CAN DELIVER FULL RATED OUTPUT VOLTAGE/CURRENT BEFORE THE OUTPUT DROPS BELOW A SPECIFIED VALUE. 1B MODE REPLY 0 CXMYJ 04LENGTH,UNTHREADED,SHANK,NOMINAL,PISTON END PISTON END NOMINAL SHANK UNTHREADED LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CXMZJ /D/ 13THREAD SIZE,NOMINAL,COUPLING COUPLING NOMINAL THREAD SIZE A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE COUPLING THREAD. 1D AND 1B MODE REPLY11AA05 CXNBJ /D/ 04DIAMETER,OUTSIDE,SMALLEST,SLEEVE SLEEVE SMALLEST OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXNCJ A13THREAD TOLERANCE CLASS,END,SECOND SECOND END THREAD TOLERANCE CLASS A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE. 1D AND 1A MODE REPLY13AN73 CXNDJ 13THREAD SIZE,CONNECTION,NOMINAL,CYLINDER END CYLINDER END NOMINAL CONNECTION THREAD SIZE NONE. 1D AND 1B MODE REPLY11AA05 CXNFJ /D/ 04DIAMETER,MAJOR,NOMINAL NOMINAL MAJOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXNGJ /D/ 04LENGTH,INSIDE,NOMINAL NOMINAL INSIDE LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CXNHJ 04DISTANCE,CENTER TO CENTER,HOLE,NOMINAL,CYLINDER END CYLINDER END NOMINAL HOLE CENTER TO CENTER DISTANCE NONE. 1D AND 1B MODE REPLY11AA05 CXNJA 19SUPPLIES PROGRAMMED PER SYSTEM,POWER POWER SUPPLIES PROGRAMMED PER SYSTEM THE NUMBER OF POWER SUPPLIES CONTROLLED BY A PROGRAMMABLE POWER SUPPLY. 1A MODE REPLY 0 CXNKA 04SIZE,FACILITY,MOUNTING MOUNTING FACILITY SIZE DESIGNATES THE SIZE OF THE MOUNTING FACILITY. 1A MODE REPLY 0 CXNLJ 04LENGTH,OVERALL,NOMINAL,CYLINDER END CYLINDER END NOMINAL OVERALL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CXNMJ /D/ 04THICKNESS,MINOR,NOMINAL NOMINAL MINOR THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 CXNND /D/ 13THREAD DIRECTION,MOUNTING FACILITY MOUNTING FACILITY THREAD DIRECTION THE DIRECTION OF THE THREAD OF THE MOUNTING FACILITY WHEN VIEWED AXIALLY.A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 CXNPJ T10RANGE,PRESSURE,OUTLET,REGULATOR REGULATOR OUTLET PRESSURE RANGE THE REGULATOR OUTLET PRESSURE RANGE OF THE ITEM. 1D AND 1F MODE REPLY13AJ40 CXNQJ 04DEPTH,RECESS,FIRST INTAKE FLANGE FIRST INTAKE FLANGE RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXNRJ 04DIAMETER,HOLE,BOLT,NOMINAL,CYLINDER END CYLINDER END NOMINAL BOLT HOLE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXNSJ /D/ 04THICKNESS,MAJOR,NOMINAL NOMINAL MAJOR THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 CXNTJ 10POWER REQUIRED,BRAKE BRAKE POWER REQUIRED THE BRAKE POWER REQUIRED TO START AND OPERATE THE ITEM INCLUDING ALL ACCESSORIES AT THE ACTUAL RATED CAPACITY,EXPRESSED IN UNIT OF POWER. 1D AND 1B MODE REPLY11AC33 CXNWJ 04DIAMETER,INSIDE,NOMINAL,CYLINDER END CYLINDER END NOMINAL INSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXNXJ 04DIAMETER,INSIDE,CLOSED CLOSED INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXNYJ /D/ 04WIDTH,MINOR,NOMINAL NOMINAL MINOR WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CXNZB 10DISSIPATION RATING IN WATTS,POWER POWER DISSIPATION RATING IN WATTS THE MAXIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY AN ITEM,EXPRESSED IN WATTS. 1B MODE REPLY 0 CXPBJ 04DIAMETER,INSIDE,LARGEST,NOMINAL,CYLINDER END CYLINDER END NOMINAL LARGEST INSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXPCJ /D/ 04DIAMETER,MINOR,NOMINAL NOMINAL MINOR DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXPDA /D/ 10TIME ACCORDING TO DIN,FLOW FLOW TIME ACCORDING TO DIN THE FLOW TIME MEASURED WITH THE FLOW CUP ACCORDING TO DIN FOR THE DETERMINATION OF THE VISCOSITY. 1A MODE REPLY 0 CXPFD 13THREAD DIRECTION,INTAKE,FIRST FIRST INTAKE THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY.A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 CXPGJ 04DIAMETER,OUTSIDE,NOMINAL,CYLINDER END CYLINDER END NOMINAL OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXPHJ /D/ 04LENGTH,LUG,NOMINAL NOMINAL LUG LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CXPJB 10CAPACITY IN NEGATIVE KILO CALORIE PER HOUR,REFRIGERATION REFRIGERATION CAPACITY IN NEGATIVE KILO CALORIE PER HOUR THE REFRIGERATION CAPACITY OF THE ITEM AS RATED BY INDUSTRY,EXPRESSED IN NEGATIVE KILO CALORIE PER HOUR. 1B MODE REPLY 0 CXPKJ 04HEIGHT,DIAL DIAL HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE DIAL,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 CXPLJ 04LENGTH,ADAPTER,COUPLING COUPLING ADAPTER LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A COUPLING ADAPTER,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CXPMJ 04THICKNESS,NOMINAL,CYLINDER END CYLINDER END NOMINAL THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 CXPNJ 19PATTERN,ANGLE,SPRAY SPRAY ANGLE PATTERN THE ANGLE PATTERN OF THE SPRAY. 1D AND 1B MODE REPLY11AP38 CXPPJ /D/ 04LENGTH BETWEEN LUG CENTER,ARC,NOMINAL NOMINAL ARC LENGTH BETWEEN LUG CENTER NONE. 1D AND 1B MODE REPLY11AA05 CXPQJ 04WIDTH,NOMINAL,CYLINDER END CYLINDER END NOMINAL WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CXPRD 12QUANTITY,LEAD THREAD LEAD THREAD QUANTITY THE NUMBER OF LEAD THREADS (HELIXES) THAT START AT THE END OF THE SCREW. SELECT REPLY CODE 10AP74 CXPSA /D/ 04SIZE,HOLE,MOUNTING,FLANGE FLANGE MOUNTING HOLE SIZE NONE. 1A MODE REPLY 0 CXPTJ 04DEPTH,FORK,NOMINAL,CYLINDER END CYLINDER END NOMINAL FORK DEPTH NONE. 1D AND 1B MODE REPLY11AA05 CXPWJ 04WIDTH,DIAL DIAL WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE DIAL,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CXPXJ /D/ 04DIAMETER,LUG,NOMINAL NOMINAL LUG DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXPYJ 04RADIUS,INSIDE,EDGE,BEARING BEARING EDGE INSIDE RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CXPZJ 04THICKNESS,ARM,FORK,NOMINAL,CYLINDER END CYLINDER END NOMINAL FORK ARM THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 CXQBJ /D/ 04DISTANCE,LUG CENTER TO LINING END,NOMINAL NOMINAL LUG CENTER TO LINING END DISTANCE NONE. 1D AND 1B MODE REPLY11AA05 CXQCJ /D/ 04THICKNESS,INSCRIPTION INSCRIPTION THICKNESS A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE HEIGHT OF THE INSCRIPTION,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CXQDJ 04DIAMETER,OUTSIDE,CLOSED CLOSED OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXQFJ 04THICKNESS,ARM,FORK,RIGHT,NOMINAL,CYLINDER END CYLINDER END NOMINAL RIGHT FORK ARM THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 CXQGJ /D/ 04LENGTH,MINOR,ARC,NOMINAL NOMINAL ARC MINOR LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CXQHJ 04DIAMETER,OUTSIDE,DIAL DIAL OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE DIAL,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CXQJA 12QUANTITY,BRANCH BRANCH QUANTITY THE NUMBER OF INDIVIDUAL BRANCHES EXTENDING FROM THE MAIN BODY OF THE ITEM. 1A MODE REPLY 0 CXQKJ 04WIDTH,SPAN,FORK,NOMINAL,CYLINDER END CYLINDER END NOMINAL FORK SPAN WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CXQLJ /D/ 04RADIUS,MINOR,NOMINAL NOMINAL MINOR RADIUS NONE. 1D AND 1B MODE REPLY11AA05 CXQMJ 04HEIGHT WITH BOOM EXTENDED,MAXIMUM,LIFT LIFT MAXIMUM HEIGHT WITH BOOM EXTENDED THE MAXIMUM MEASUREMENT FROM GROUND LEVEL TO THE UPPERMOST PORTION OF THE LIFT WITH THE BOOM EXTENDED. 1D AND 1B MODE REPLY11AA05 CXQNJ /D/ 10REACH,HORIZONTAL,MAXIMUM.LIFT MAXIMUM.LIFT HORIZONTAL REACH A MEASUREMENT OF THE MAXIMUM HORIZONTAL DISTANCE THE LIFT CAN REACH. 1D AND 1B MODE REPLY11AA05 CXQPJ 04LENGTH,SHANK,NOMINAL,CYLINDER END CYLINDER END NOMINAL SHANK LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CXQQJ 10MOVEMENT,ACTUATOR ACTUATOR MOVEMENT THE MOVEMENT OF THE SWITCH ACTUATOR. 3D AND 1B MODE REPLY32AL771AA051AC20 CXQRJ 10CURRENT RATING AT MAXIMUM RATED VOLTAGE,CONTACT LOAD CONTACT LOAD CURRENT RATING AT MAXIMUM RATED VOLTAGE THE AMOUNT OF CURRENT THE CONTACTS ARE RATED TO MAKE OR BREAK AT MAXIMUM RATED VOLTAGE,WITH A SPECIFIED LOAD. 3D AND 1B MODE REPLY31AC302AK531AE16 CXQSJ 10POWER RATING,ENGINE ENGINE POWER RATING THE POWER PRODUCED BY THE ENGINE UNDER STANDARD OPERATING CONDITIONS. 1D AND 1B MODE REPLY12AJ20 CXQTJ 04DIAMETER,SHANK,NOMINAL,CYLINDER END CYLINDER END NOMINAL SHANK DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXQWL 16STYLE,HUB HUB STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HUB. 1L MODE REPLY 0 CXQXJ 04LENGTH,UNTHREADED,SHANK,NOMINAL,CYLINDER END CYLINDER END NOMINAL SHANK UNTHREADED LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CXQYJ /D/ 04WIDTH,MAJOR,NOMINAL NOMINAL MAJOR WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CXQZD 18TYPE,BAND,WRIST WRIST BAND TYPE INDICATES THE TYPE OF WRIST BAND. SELECT REPLY CODE 10AC55 CXRBJ 04DISTANCE BETWEEN HOLE/STUD CENTERS,HORIZONTAL,NOMINAL NOMINAL HORIZONTAL DISTANCE BETWEEN HOLE/STUD CENTERS NONE. 1D AND 1B MODE REPLY11AA05 CXRCJ /D/ 04DIAMETER,OUTSIDE,NOMINAL,CONNECTION CONNECTION NOMINAL OUTSIDE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CONNECTION,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXRDJ /D/ 04DIAMETER,THRU-HOLE,NOMINAL NOMINAL THRU-HOLE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXRFJ 04DIMENSION,MESH MESH DIMENSION A MEASUREMENT OF THE MESH OPENING. 1D AND 1B MODE REPLY11AA05 CXRGJ /D/ 04DIAMETER,SPLINE,EXTERNAL EXTERNAL SPLINE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXRHJ /D/ 04DISTANCE BETWEEN HOLE/STUD CENTERS,VERTICAL,NOMINAL NOMINAL VERTICAL DISTANCE BETWEEN HOLE/STUD CENTERS NONE. 1D AND 1B MODE REPLY11AA05 CXRJD /D/ 19CONFIGURATION,FLANGE FLANGE CONFIGURATION THE PHYSICAL CONFIGURATION OF THE FLANGE. SELECT REPLY CODE 10AE88 CXRKJ /D/ 04DIAMETER,INSIDE,NOMINAL,CONNECTION CONNECTION NOMINAL INSIDE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CONNECTION,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXRLJ 04THICKNESS,END,CONNECTION CONNECTION END THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 CXRMJ /D/ 04DIAMETER,OUTSIDE,NOMINAL,FLANGE FLANGE NOMINAL OUTSIDE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FLANGE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXRND /D/ 07ACCURACY,DEGREE DEGREE ACCURACY AN INDICATION OF THE DEGREE OF ACCURACY OF THE ITEM CORRESPONDING TO A SPECIFICATION. SELECT REPLY CODE 10AP71 CXRPJ /D/ 04DIAMETER,LARGEST,SHAFT SHAFT LARGEST DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXRQJ 04WIDTH,OVERALL,NOMINAL NOMINAL OVERALL WIDTH THE NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CXRSD 13THREAD DIRECTION,INTAKE,SECOND SECOND INTAKE THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY.A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 CXRTJ /D/ 04DIAMETER,OVERALL,NOMINAL NOMINAL OVERALL DIAMETER THE NOMINAL MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE. 1D AND 1B MODE REPLY11AA05 CXRWJ /D/ 04DISTANCE FROM BEND TO CENTERLINE DISTANCE FROM BEND TO CENTERLINE NONE. 1D AND 1B MODE REPLY11AA05 CXRXA 12QUANTITY,SPLINE,HUB HUB SPLINE QUANTITY THE NUMBER OF SPLINES ON THE HUB OF THE ITEM. 1A MODE REPLY 0 CXRYJ 04DIAMETER,MAJOR,NOMINAL,SPLINE,HUB HUB SPLINE NOMINAL MAJOR DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CIRCULAR CROSS SECTION OF THE HUB SPLINE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXRZJ 04DIAMETER,PITCH,SPLINE,HUB HUB SPLINE PITCH DIAMETER A MEASUREMENT OF THE HUB SPLINE PITCH DIAMETER. 2D AND 1B MODE REPLY21AA051AC20 CXSBD /D/ 18TYPE FOR WHICH DESIGNED,BRAKE BRAKE TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF BRAKE FOR WHICH DESIGNED. SELECT REPLY CODE 10AJ68 CXSCJ /D/ 04DIAMETER,INSIDE,MAJOR,NOMINAL NOMINAL MAJOR INSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXSDB /D/ 03DESIGNATION,SIZE SIZE DESIGNATION A DESIGNATION INDICATING THE SIZE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1B MODE REPLY 0 CXSFJ /D/ 04DIAMETER,OUTSIDE,MAJOR,NOMINAL NOMINAL MAJOR OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXSGJ 04LENGTH,BEAM BEAM LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE BEAM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CXSHJ /D/ 04DIAMETER,INSIDE,MINOR,NOMINAL NOMINAL MINOR INSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXSJA 04SPACING,FACILITY,MOUNTING MOUNTING FACILITY SPACING THE SPACING BETWEEN THE MOUNTING FACILITIES. 1A MODE REPLY 0 CXSKJ /D/ 04DIAMETER,OUTSIDE,MINOR,NOMINAL NOMINAL MINOR OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXSLJ /D/ 04LENGTH,CENTER,TANGENT TANGENT CENTER LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXSMJ /D/ 04DIAMETER,SPLINE,INTERNAL INTERNAL SPLINE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXSNJ /D/ 04DIAMETER,OUTSIDE,NOMINAL,BODY BODY NOMINAL OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CXSPL 16STYLE,SLOT,SKIRT SKIRT SLOT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SKIRT SLOT. 1L MODE REPLY 0 CXSQJ /D/ 04DISTANCE FROM BOTTOM OF BODY TO CENTER OF INLET,NOMINAL NOMINAL DISTANCE FROM BOTTOM OF BODY TO CENTER OF INLET NONE. 1D AND 1B MODE REPLY11AA05 CXSRJ 04DEPTH,RECESS,FIRST DISCHARGE FLANGE FIRST DISCHARGE FLANGE RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXSSD /D/ 19POSITION,GUIDE,POLARIZING POLARIZING GUIDE POSITION THE SPECIFIC POSITION OF THE POLARIZING GUIDE. SELECT REPLY CODE 10AC95 CXSTJ /D/ 04LENGTH,NOMINAL,BODY BODY NOMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CXSWJ /D/ 04DISTANCE FROM END OF NOZZLE TO CENTER OF INLET,NOMINAL NOMINAL DISTANCE FROM END OF NOZZLE TO CENTER OF INLET NONE. 1D AND 1B MODE REPLY11AA05 CXSXL 16STYLE,DISCONNECT,QUICK,DISCHARGE CONNECTION DISCHARGE CONNECTION QUICK DISCONNECT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE DISCHARGE QUICK DISCONNET. 1L MODE REPLY 0 CXSYJ /D/ 04DISTANCE BETWEEN CONNECTIONS,CENTER TO CENTER,NOMINAL NOMINAL CENTER TO CENTER DISTANCE BETWEEN CONNECTIONS NONE. 1D AND 1B MODE REPLY11AA05 CXSZJ /D/ 04LENGTH,LEG,TUBE TUBE LEG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE TUBE LEG,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CXTBJ 10SIZE,HUB HUB SIZE NONE. 2D AND 1B MODE REPLY21AA051AC20 CXTCJ 10SIZE,END,HUB HUB END SIZE NONE. 2D AND 1B MODE REPLY21AA051AC20 CXTDJ 04LENGTH,SPUR,END,HUB HUB END SPUR LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXTFJ /D/ 04DIAMETER,HOLE HOLE DIAMETER PLEASE USE MRC AAUB IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 CXTGJ /D/ 04WIDTH,OPENING,HOOK HOOK OPENING WIDTH PLEASE USE MRC AAUF IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 CXTHJ 04LENGTH,END END LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXTJJ 04LENGTH,INSIDE,COIL TO HOOK COIL TO HOOK INSIDE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXTKJ 04WIDTH,HOOK HOOK WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXTLJ 04LENGTH,HOOK,END END HOOK LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXTMJ 04LENGTH FROM COIL AXIS TO FIRST BEND,END END LENGTH FROM COIL AXIS TO FIRST BEND NONE. 2D AND 1B MODE REPLY21AA051AC20 CXTNJ 04LENGTH FROM FIRST BEND TO SECOND BEND OR END,END END LENGTH FROM FIRST BEND TO SECOND BEND OR END NONE. 2D AND 1B MODE REPLY21AA051AC20 CXTPJ 04LENGTH FROM SECOND BEND TO THIRD BEND OR END,END END LENGTH FROM SECOND BEND TO THIRD BEND OR END NONE. 2D AND 1B MODE REPLY21AA051AC20 CXTQJ 04LENGTH FROM THIRD BEND OR END,END END LENGTH FROM THIRD BEND OR END NONE. 2D AND 1B MODE REPLY21AA051AC20 CXTRJ 04LENGTH,LEG,HOOK HOOK LEG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXTSJ 04ANGLE,TANGENT,END END TANGENT ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CXTTD 13THREAD DIRECTION,DISCHARGE,SECOND SECOND DISCHARGE THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY.A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 CXTWJ 04DIAMETER WITHOUT BUSHING,INSIDE,EYE EYE INSIDE DIAMETER WITHOUT BUSHING NONE. 2D AND 1B MODE REPLY21AA051AC20 CXTXJ 04DIAMETER WITH BUSHING,INSIDE,EYE EYE INSIDE DIAMETER WITH BUSHING NONE. 2D AND 1B MODE REPLY21AA051AC20 CXTYJ 04RADIUS,WRAP WRAP RADIUS NONE. 2D AND 1B MODE REPLY21AA051AC20 CXTZJ 04HEIGHT,WRAP/BEND WRAP/BEND HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CXWBJ 04HEIGHT,CLAMP CLAMP HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CXWCJ 04DIAMETER,HOLE,BOLT,CLAMP CLAMP BOLT HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXWDJ 04ANGLE,TANGENT,CENTER CENTER TANGENT ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CXWFL 16STYLE,CENTER CENTER STYLE THE PREFORMED SHAPE OF THE MIDDLE SECTION OF THE ITEM. 1L MODE REPLY 0 CXWGD 03DESIGNATION,LEAF TYPE,INDIVIDUAL INDIVIDUAL LEAF TYPE DESIGNATION THE INDIVIDUAL LEAF TYPE DESIGNATION. SELECT REPLY CODE 10AG12 CXWHD /D/ 03DESIGNATION,LEAF STYLE,INDIVIDUAL INDIVIDUAL LEAF STYLE DESIGNATION THE INDIVIDUAL LEAF STYLE DESIGNATION. SELECT REPLY CODE 10AM40 CXWJD 18TYPE,CONTAINER,IMMEDIATE IMMEDIATE CONTAINER TYPE INDICATES THE TYPE OF CONTAINER WITH WHICH THE ITEM IS IN DIRECT CONTACT. SELECT REPLY CODE 10AN65 CXWKJ /D/ 04ANGLE BETWEEN CONNECTIONS,NOMINAL NOMINAL ANGLE BETWEEN CONNECTIONS HONE. 1D AND 1B MODE REPLY11AP38 CXWLJ /D/ 04DEPTH,OVERALL,NOMINAL NOMINAL OVERALL DEPTH NONE. 1D AND 1B MODE REPLY11AA05 CXWMD /D/ 18TYPE,CONNECTION,PIPE PIPE CONNECTION TYPE INDICATES THE TYPE OF PIPE CONNECTION. SELECT REPLY CODE 10AB76 CXWNJ /D/ 04LENGTH,SPOOL,NOMINAL NOMINAL SPOOL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CXWPL /D/ 16STYLE,CONNECTION,PIPE PIPE CONNECTION STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PIPE CONNECTION. 1L MODE REPLY 0 CXWQD /D/ 18TYPE,CONNECTION,TUBE TUBE CONNECTION TYPE INDICATES THE TYPE OF TUBE CONNECTION. SELECT REPLY CODE 10AB76 CXWRL /D/ 16STYLE,CONNECTION,TUBE TUBE CONNECTION STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE TUBE CONNECTION. 1L MODE REPLY 0 CXWSJ /D/ 13THREAD SIZE,PIPE,NOMINAL NOMINAL PIPE THREAD SIZE DESIGNATES THE NOMINAL THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE PIPE. 1D AND 1B MODE REPLY11AA05 CXWTJ /D/ 13THREAD SIZE,TUBE,NOMINAL NOMINAL TUBE THREAD SIZE DESIGNATES THE NOMINAL THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE TUBE. 1D AND 1B MODE REPLY11AA05 CXWWJ /D/ 04LENGTH,LEG,PIPE PIPE LEG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE PIPE LEG,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CXWXJ /D/ 04DEPTH,RECESS,SECOND INTAKE FLANGE SECOND INTAKE FLANGE RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXWYL 16STYLE,STRIKE,CATCH CATCH STRIKE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CATCH STRIKE. 1L MODE REPLY 0 CXWZJ /D/ 04THICKNESS,OVERALL OVERALL THICKNESS AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM, IN DISTINCTION FROM LENGTH OR WIDTH. PLEASE USE MRC ADUM IN PLACE OF THIS DISCONTINUED MRC. 2D AND 1B MODE REPLY21AA051AC20 CXXBJ 04ANGLE,EDGE,FEATHER FEATHER EDGE ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CXXCJ 04DISTANCE FROM END TO PIVOT POINT DISTANCE FROM END TO PIVOT POINT NONE. 2D AND 1B MODE REPLY21AA051AC20 CXXDJ 04DIAMETER,HOLE,SURFACE SURFACE HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXXFA 12QUANTITY,HOLE,SURFACE SURFACE HOLE QUANTITY NONE. 1A MODE REPLY 0 CXXGJ 04ANGLE,COUNTERSINK COUNTERSINK ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CXXHJ 04WIDTH,SLOT,LEFT LEFT SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXXJJ 10CAPACITY,LOAD LOAD CAPACITY THE RATED LOAD THE ITEM CAN ACCOMMODATE. 2D AND 1B MODE REPLY22AG671AC20 CXXKJ 04DEPTH,SLOT,LEFT LEFT SLOT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXXLJ 04WIDTH,SLOT,RIGHT RIGHT SLOT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXXMJ 04DEPTH,SLOT,RIGHT RIGHT SLOT DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXXNJ 04DEPTH,COUNTERBORE,LEFT LEFT COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXXPJ 04DIAMETER,COUNTERBORE,LEFT LEFT COUNTERBORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXXQJ 04DEPTH,COUNTERBORE,RIGHT RIGHT COUNTERBORE DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXXRJ 04DIAMETER,COUNTERBORE,RIGHT RIGHT COUNTERBORE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXXSJ 04DIAMETER,PROJECTION.LEFT LEFT PROJECTION DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXXTJ 04LENGTH,PROJECTION.LEFT LEFT PROJECTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXXWJ 04DIAMETER,PROJECTION.RIGHT RIGHT PROJECTION DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXXXJ 04LENGTH,PROJECTION,RIGHT RIGHT PROJECTION LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXXYJ 04WIDTH ACROSS FLATS,SHOULDER,SECOND SECOND SHOULDER WIDTH ACROSS FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 CXXZJ 04ANGLE,COUNTERSINK,LEFT LEFT COUNTERSINK ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CXYBJ 04ANGLE,COUNTERSINK,RIGHT RIGHT COUNTERSINK ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CXYCJ 04ANGLE,CHAMFER,END,LEFT LEFT END CHAMFER ANGLE NONE. REPLACED BY MRC CSYT WITH ISAC 0368. 2D AND 1B MODE REPLY21AP381AC20 CXYDJ 04ANGLE,CHAMFER,END,RIGHT RIGHT END CHAMFER ANGLE NONE. REPLACED BY MRC CSYT WITH ISAC 0368. 2D AND 1B MODE REPLY21AP381AC20 CXYFJ 04ANGLE,CHAMFER,PROJECTION.LEFT PROJECTION.LEFT CHAMFER ANGLE NONE. REPLACED BY MRC CSYT WITH ISAC 0368. 2D AND 1B MODE REPLY21AP381AC20 CXYGD 13THREAD DIRECTION,DISCHARGE,FIRST FIRST DISCHARGE THREAD DIRECTION THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY.A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. SELECT REPLY CODE 10AA38 CXYHJ 04ANGLE,CHAMFER,PROJECTION,RIGHT RIGHT PROJECTION CHAMFER ANGLE NONE. REPLACED BY MRC CSYT WITH ISAC 0368. 2D AND 1B MODE REPLY21AP381AC20 CXYJH /D/ 17SURFACE TREATMENT,CONTACT CONTACT SURFACE TREATMENT THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE CONTACT IS PLATED,DIPPED,AND/OR COATED. THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE/S/ AND CANNOT BE WIPED OFF. 3D MODE REPLY 31AP551AP566AD09 CXYKL /D/ 16STYLE DESIGNATOR,END END STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END. 1L MODE REPLY 0 CXYLJ /D/ 04DIAMETER,NOMINAL,HOLE,FORK CROSS FORK CROSS HOLE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FORK CROSS HOLE AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXYMJ /D/ 04HEIGHT,NOMINAL,FORK FORK NOMINAL HEIGHT A NOMINAL MEASUREMENT FROM THE BOTTOM TO THE TOP OF A FORK,IN DISTINCTION FROM DEPTH. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1D AND 1B MODE REPLY11AA05 CXYNJ /D/ 04DISTANCE BETWEEN FORK HOLES,NOMINAL NOMINAL DISTANCE BETWEEN FORK HOLES THE NOMINAL DISTANCE BETWEEN FORK HOLES. 1D AND 1B MODE REPLY11AA05 CXYPJ /D/ 04DISTANCE BETWEEN MOUNTING HOLES ALONG WIDTH,CENTER TO CENTER,NOMINAL NOMINAL CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES ALONG WIDTH A NOMINAL MEASUREMENT OF THE CENTER TO CENTER DISTANCE BETWEEN THE MOUNTING HOLES ALONG THE WIDTH. 1D AND 1B MODE REPLY11AA05 CXYQJ /D/ 04DISTANCE BETWEEN MOUNTING HOLES ALONG LENGTH,CENTER TO CENTER,NOMINAL NOMINAL CENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES ALONG LENGTH A NOMINAL MEASUREMENT OF THE CENTER TO CENTER DISTANCE BETWEEN THE MOUNTING HOLES ALONG THE LENGTH. 1D AND 1B MODE REPLY11AA05 CXYRJ 04ANGLE BETWEEN FLATS,END,SECOND SECOND END ANGLE BETWEEN FLATS NONE. 2D AND 1B MODE REPLY21AF981AC20 CXYSJ /D/ 04DISTANCE FROM CENTERLINE TO KEYING FACILITY DISTANCE FROM CENTERLINE TO KEYING FACILITY THE DISTANCE BETWEEN THE CENTERLINE AND THE KEYING FACILITY. 1D AND 1B MODE REPLY11AA05 CXYTJ /D/ 04WIDTH,NOMINAL,FACILITY,KEYING KEYING FACILITY NOMINAL WIDTH A NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A KEYING FACILITY,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CXYWJ /D/ 04DISTANCE ACROSS CORNERS,NOMINAL NOMINAL DISTANCE ACROSS CORNERS THE NOMINAL DISTANCE BETWEEN ONE CORNER TO THE OPPOSITE CORNER. 1D AND 1B MODE REPLY11AA05 CXYXJ /D/ 04DIAMETER,MAXIMUM,BORE BORE MAXIMUM DIAMETER THE MAXIMUM LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BORE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXYYJ /D/ 04DIAMETER,OUTSIDE,NOMINAL,HUB HUB NOMINAL OUTSIDE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HUB,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXYZJ /D/ 04LENGTH,NOMINAL,BORE BORE NOMINAL LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF A BORE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CXZBB /D/ 13THREAD PITCH IN MILLIMETERS,ACCOMMODATION,TERMINAL,SPARK PLUG SPARK PLUG TERMINAL ACCOMMODATION THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREADED AXIS OF THE SPARK PLUG TERMINAL ACCOMMODATION,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CXZCB /D/ 13THREAD PITCH IN MILLIMETERS,ACCOMMODATION,TERMINAL,COIL COIL TERMINAL ACCOMMODATION THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREADED AXIS OF THE COIL TERMINAL ACCOMMODATION,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CXZDB /D/ 13THREAD PITCH IN MILLIMETERS,ACCOMMODATION,TERMINAL,PRIMARY PRIMARY TERMINAL ACCOMMODATION THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREADED AXIS OF THE PRIMARY TERMINAL ACCOMMODATION,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CXZFL 16STYLE,END,EYE EYE END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE EYE END. 1L MODE REPLY 0 CXZGD 14SHAPE,STRIP,ADHESIVE ADHESIVE STRIP SHAPE THE PHYSICAL CONFIGURATION OF THE ADHESIVE STRIP. SELECT REPLY CODE 10AD07 CXZHJ 04WIDTH ACCOMMODATED,BEAM BEAM WIDTH ACCOMMODATED A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BEAM ACCOMMODATED,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CXZJJ /D/ 04DEPTH,RECESS,SECOND DISCHARGE FLANGE SECOND DISCHARGE FLANGE RECESS DEPTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXZKJ /D/ 04DISTANCE FROM HOLE CENTER TO RADIUS ORIGINATING POINT DISTANCE FROM HOLE CENTER TO RADIUS ORIGINATING POINT NONE. 2D AND 1B MODE REPLY21AA051AC20 CXZLJ /D/ 04DISTANCE FROM APERTURE CENTER TO HOLE CENTER DISTANCE FROM APERTURE CENTER TO HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXZMJ 04LENGTH,ADJUSTING MECHANISM ADJUSTING MECHANISM LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CXZNJ 04DISTANCE FROM CENTERLINE TO HOLE CENTER DISTANCE FROM CENTERLINE TO HOLE CENTER NONE. 2D AND 1B MODE REPLY21AA051AC20 CXZPJ 04DISTANCE BETWEEN CLAMP HALVES DISTANCE BETWEEN CLAMP HALVES NONE. 2D AND 1B MODE REPLY21AA051AC20 CXZQJ 04DISTANCE FROM HOLE CENTER TO MOUNTING SURFACE DISTANCE FROM HOLE CENTER TO MOUNTING SURFACE NONE. 2D AND 1B MODE REPLY21AA051AC20 CXZRJ 04HEIGHT,INSIDE,JAW JAW INSIDE HEIGHT NONE. 2D AND 1B MODE REPLY21AA051AC20 CXZSD /D/ 18TYPE,INSTALLATION,CONNECTION,HUB HUB CONNECTION INSTALLATION TYPE INDICATES THE TYPE OF AXIAL MOVEMENT IN THE HUB CONNECTION INSTALLATION. SELECT REPLY CODE 10AK95 CXZTJ /D/ 08LOCATION IN RELATION TO KEYING FACILITY,HOLE HOLE LOCATION IN RELATION TO KEYING FACILITY THE DISTANCE BETWEEN THE HOLE AND THE KEYING FACILITY. 1D AND 1B MODE REPLY11AA05 CXZWJ /D/ 04LENGTH,NOMINAL,SPLINE SPLINE NOMINAL LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF A SPLINE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CXZXD 19SYSTEM FOR WHICH DESIGNED,FILTERING FILTERING SYSTEM FOR WHICH DESIGNED THE FILTERING SYSTEM FOR WHICH THE ITEM IS DESIGNED TO BE USED. SELECT REPLY CODE 10AL92 CXZYJ /D/ 04DIAMETER,OUTSIDE,NOMINAL,SHAFT SHAFT NOMINAL OUTSIDE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SHAFT,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CXZZJ /D/ 04DIAMETER,PITCH PITCH DIAMETER A MEASUREMENT INDICATING THE DIAMETER-PITCH PER SPECIFIC MEASUREMENT SCALE OF THE ITEM. 1D AND 1B MODE REPLY11AA05 CYAAJ A18TYPE AND QUANTITY,CONTACT CONTACT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF CONTACTS WHICH MAKEUP THE ASSORTMENT OF THE ITEM. 1D AND 1A MODE REPLY12AG81 CYABJ /D/A19ITEMS,SUPPLY,CONTACT CONTACT SUPPLY ITEMS A LISTING OF THOSE CONTACTS AS INDICATED BY AN ITEM NAME AND A NATIONAL STOCK NUMBER. 1D AND 1A MODE REPLY12AG81 CYACJ /D/ 19ITEMS,NONSUPPLY,CONTACT CONTACT NONSUPPLY ITEMS A LISTING OF THOSE CONTACTS WITHOUT A NATIONAL STOCK NUMBER. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1D AND 1B MODE REPLY12AG81 CYADJ 04SIZE FOR WHICH DESIGNED,CYLINDER,GUIDE,NOMINAL NOMINAL GUIDE CYLINDER SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE GUIDE CYLINDER FOR WHICH THE ITEM IS DESIGNED,EXPRESSED IN NOMINAL TERMS. 1D AND 1B MODE REPLY11AA05 CYAEA 19SOURCE,COMPRESSOR COMPRESSOR SOURCE THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE GOVERNMENT AGENCY,INDUSTRIAL ORGANIZATION,OR OTHER SOURCE,WHICH CONTROLS OR MANUFACTURES THE COMPRESSOR. 1A MODE REPLY 0 CYAFA 19NUMBER FOR WHICH DESIGNED,MODEL,COMPRESSOR COMPRESSOR MODEL NUMBER FOR WHICH DESIGNED THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE COMPRESSOR FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 CYAGJ 04HEIGHT,OVERALL,NOMINAL NOMINAL OVERALL HEIGHT THE NOMINAL DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM. 1D AND 1B MODE REPLY11AA05 CYAHJ 04HEIGHT ABOVE FLOOR,PLATFORM,NOMINAL NOMINAL PLATFORM HEIGHT ABOVE FLOOR A NOMINAL MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE PLATFORM ABOVE THE FLOOR,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 CYAJD 09MATERIAL,BOX BOX MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE BOX IS FABRICATED. SELECT REPLY CODE 10MA01 CYAKJ 04LENGTH,PLATFORM,NOMINAL NOMINAL PLATFORM LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE PLATFORM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CYALJ 04WIDTH,PLATFORM,NOMINAL NOMINAL PLATFORM WIDTH A NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PLATFORM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CYAMJ 04LENGTH,SHELF,NOMINAL NOMINAL SHELF LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE SHELF,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CYANJ 04WIDTH,SHELF,NOMINAL NOMINAL SHELF WIDTH A NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SHELF,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CYAPJ 04HEIGHT,STAKE,NOMINAL NOMINAL STAKE HEIGHT A NOMINAL MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE STAKE,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 CYAQJ 04DIAMETER,ELEMENT,ROLLING,NOMINAL NOMINAL ROLLING ELEMENT DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A ROLLING ELEMENT,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CYARD 09MATERIAL,FRAME FRAME MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE FRAME IS FABRICATED. SELECT REPLY CODE 10MA01 CYASD 09MATERIAL,HANDLE HANDLE MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE HANDLE IS FABRICATED. SELECT REPLY CODE 10MA01 CYATD 09MATERIAL,SHELF SHELF MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE SHELF IS FABRICATED. SELECT REPLY CODE 10MA01 CYAUD 09MATERIAL,SCREW SCREW MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE SCREW IS FABRICATED. SELECT REPLY CODE 10MA01 CYAVD 09MATERIAL,LOCKING FEATURE LOCKING FEATURE MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE LOCKING FEATURE IS FABRICATED. SELECT REPLY CODE 10MA01 CYAWJ A19DOCUMENT AND CLASSIFICATION,MATERIAL,SCREW SCREW MATERIAL DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS CLASS,CONDITION,TEMPER,AND THE LIKE,THAT IDENTIFIES THE SCREW MATERIAL. 2D AND 1A MODE REPLY21AP331AP18 CYAXJ A19DOCUMENT AND CLASSIFICATION,MATERIAL,LOCKING FEATURE LOCKING FEATURE MATERIAL DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS CLASS,CONDITION,TEMPER,AND THE LIKE,THAT IDENTIFIES THE LOCKING FEATURE MATERIAL. 2D AND 1A MODE REPLY21AP331AP18 CYAYD 17SURFACE TREATMENT,BEARING SURFACE OF HEAD BEARING SURFACE OF HEAD SURFACE TREATMENT THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE BEARING SURFACE OF HEAD IS PLATED,DIPPED AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF. SELECT REPLY CODE 10SF01 CYAZD 17SURFACE TREATMENT,HEAD HEAD SURFACE TREATMENT THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE HEAD IS PLATED,DIPPED AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF. SELECT REPLY CODE 10SF01 CYBAD 17SURFACE TREATMENT,SCREW SCREW SURFACE TREATMENT THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE SCREW IS PLATED,DIPPED AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF. SELECT REPLY CODE 10SF01 CYBBD 17SURFACE TREATMENT,SHANK SHANK SURFACE TREATMENT THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE SHANK IS PLATED,DIPPED AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF. SELECT REPLY CODE 10SF01 CYBCJ A19DOCUMENT AND CLASSIFICATION,SURFACE TREATMENT,BEARING SURFACE OF HEAD BEARING SURFACE OF HEAD SURFACE TREATMENT DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL OF THE BEARING SURFACE OF HEAD. 2D AND 1A MODE REPLY21AP331AP39 CYBDJ A19DOCUMENT AND CLASSIFICATION,SURFACE TREATMENT,HEAD HEAD SURFACE TREATMENT DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL OF THE HEAD. 2D AND 1A MODE REPLY21AP331AP39 CYBEJ A19DOCUMENT AND CLASSIFICATION,SURFACE TREATMENT,SCREW SCREW SURFACE TREATMENT DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL OF THE SCREW. 2D AND 1A MODE REPLY21AP331AP39 CYBFJ A19DOCUMENT AND CLASSIFICATION,SURFACE TREATMENT,SHANK SHANK SURFACE TREATMENT DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL OF THE SHANK. 2D AND 1A MODE REPLY21AP331AP39 CYBGL 16STYLE,CONFIGURATION,HOLE,HEAD HEAD HOLE CONFIGURATION STYLE THE STYLE DESIGNATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HOLE CONFIGURATION IN THE HEAD. 1L MODE REPLY 0 CYBHJ 19FINISH,SURFACE,BEARING SURFACE OF HEAD BEARING SURFACE OF HEAD SURFACE FINISH DESIGNATES THE SPECIFIC SURFACE ROUGHNESS RATING,REPRESENTING THE ARITHMETIC AVERAGE DEVIATION OF THE BEARING SURFACE OF HEAD FROM THE MEANLINE IN PROFILE. 1D AND 1B MODE REPLY11AE86 CYBJD 09MATERIAL,DISK DISK MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED. SELECT REPLY CODE 10MA01 CYBKJ 19FINISH,SURFACE,SHANK SHANK SURFACE FINISH DESIGNATES THE SPECIFIC SURFACE ROUGHNESS RATING,REPRESENTING THE ARITHMETIC AVERAGE DEVIATION OF THE SHANK SURFACE FROM THE MEANLINE IN PROFILE. 1D AND 1B MODE REPLY11AE86 CYBLJ 19FINISH,SURFACE,THREAD THREAD SURFACE FINISH DESIGNATES THE SPECIFIC SURFACE ROUGHNESS RATING,REPRESENTING THE ARITHMETIC AVERAGE DEVIATION OF THE THREAD SURFACE FROM THE MEANLINE IN PROFILE. 1D AND 1B MODE REPLY11AE86 CYBMD 09MATERIAL,SEAT SEAT MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED. SELECT REPLY CODE 10MA01 CYBND 09MATERIAL,STEM STEM MATERIAL THE CHEMCIAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED. SELECT REPLY CODE 10MA01 CYBPJ A19DOCUMENT AND CLASSIFICATION,MATERIAL,DISK DISK MATERIAL DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS CLASS,CONDITION,TEMPER,AND THE LIKE,THAT IDENTIFIES THE MATERIAL. 2D AND 1A MODE REPLY21AP331AP18 CYBQJ A19DOCUMENT AND CLASSIFICATION,MATERIAL,SEAT SEAT MATERIAL DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS CLASS CONDITION,TEMPER,AND THE LIKE,THAT IDENTIFIES THE MATERIAL. 2D AND 1A MODE REPLY21AP331AP18 CYBRJ A19DOCUMENT AND CLASSIFICATION,MATERIAL,STEM STEM MATERIAL DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS CLASS,CONDITION,TEMPER,AND THE LIKE,THAT IDENTIFIES THE MATERIAL. 2D AND 1A MODE REPLY21AP331AP18 CYBSJ /D/ 04DIAMETER TUBE ACCOMMODATED,INSIDE,FIRST END FIRST END INSIDE DIAMETER TUBE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CYBTJ /D/ 04DIAMETER TUBE ACCOMMODATED,INSIDE,SECOND END SECOND END INSIDE DIAMETER TUBE ACCOMMODATED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CYBUL /D/ 16STYLE,FLANGE FACE,END,FIRST FIRST END FLANGE FACE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FLANGE FACE. 1L MODE REPLY 0 CYBVL /D/ 16STYLE,FLANGE FACE,END,SECOND SECOND END FLANGE FACE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FLANGE FACE. 1L MODE REPLY 0 CYBWD /D/ 18TYPE,SEGMENT,CUTTING CUTTING SEGMENT TYPE INDICATES THE TYPE OF CUTTING SEGMENT WHICH THE ITEM IS EQUIPPED. SELECT REPLY CODE 10AK54 CYBXJ 04WIDTH,SEGMENT,CUTTING CUTTING SEGMENT WIDTH A MEASUREMENT OF THE CUTTING SEGMENT WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CYBYD 19GRADE,BLADE BLADE GRADE INDICATES THE GRADE WHICH IDENTIFIES THE QUALITY OF THE BLADE. SELECT REPLY CODE 10AK54 CYBZD 19RELATIONSHIP WITH OUTLET,INLET INLET RELATIONSHIP WITH OUTLET INDICATES WHETHER OR NOT THE INLET IS IDENTICAL TO THE OUTLET. SELECT REPLY CODE 10AN69 CYCAJ 19CLASS,PRESSURE PRESSURE CLASS THE PRESSURE CLASS DESIGNATION AT WHICH THE ITEM IS RATED FOR OPERATION. 1D AND 1B MODE REPLY11AB18 CYCBD 18TYPE,END,ACTUATING,STEM STEM ACTUATING END TYPE INDICATES THE TYPE OF ACTUATING END ON THE ITEM. SELECT REPLY CODE 10AK84 CYCCD 18TYPE,END,CONTROL,FLOW FLOW CONTROL END TYPE INDICATES THE TYPE OF FLOW CONTROL END ON THE ITEM. SELECT REPLY CODE 10AK84 CYCDL 16STYLE, DISK DISK STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE DISK. 1L MODE REPLY 0 CYCEJ 04DIAMETER,PLUG PLUG DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PLUG,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CYCFJ 04DIAMETER,PLUG,MAJOR MAJOR PLUG DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CIRCULAR CROSS SECTION OF THE TAPERED PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CYCGJ 04DIAMETER,PLUG,MINOR MINOR PLUG DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST CIRCULAR CROSS SECTION OF THE TAPERED PORTION,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CYCHJ 04LENGTH,PLUG PLUG LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE PLUG,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CYCJA 12QUANTITY,PORT PORT QUANTITY THE NUMBER OF PORTS PROVIDED ON THE ITEM. 1A MODE REPLY 0 CYCKD 14SHAPE,PORT PORT SHAPE THE PHYSICAL CONFIGURATION OF THE PORT. SELECT REPLY CODE 10AD07 CYCLJ 04DIAMETER,PORT PORT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PORT,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CYCMJ 04LENGTH,PORT PORT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A PORT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CYCNJ 04WIDTH,PORT PORT WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A PORT,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CYCPD 18TYPE,DISPLAY DISPLAY TYPE THE TYPE DESIGNATION INDICATING THE DISPLAY THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM. SELECT REPLY CODE 10AP20 CYCQH 01COLOR,DISPLAY,ILLUMINATED ILLUMINATED DISPLAY COLOR THE HUE OR TINT OF THE DISPLAY WHEN ILLUMINATED BY A LIGHT SOURCE. 3D MODE REPLY 32AP202AK176AD06 CYCRH 01COLOR,INSCRIPTION,ILLUMINATED ILLUMINATED INSCRIPTION COLOR THE HUE OR TINT OF THE INSCRIPTION WHEN ILLUMINATED BY A LIGHT SOURCE. 3D MODE REPLY 32AP202AK176AD06 CYCSJ 10VOLTAGE RATING IN VOLTS,MAXIMUM,CONTACT CONTACT MAXIMUM VOLTAGE RATING IN VOLTS THE HIGHEST VOLTAGE AT WHICH THE CONTACTS ARE RATED FOR NORMAL OPERATING,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY12AN87 CYCTJ 10CURRENT RATING IN AMPS,MAXIMUM,CONTACT CONTACT MAXIMUM CURRENT RATING IN AMPS THE HIGHEST CURRENT AT WHICH THE CONTACTS ARE RATED FOR NORMAL OPERATION,EXPRESSED IN AMPS. 1D AND 1B MODE REPLY12AN87 CYCUB 10VOLTAGE RATING IN VOLTS,HEATER HEATER VOLTAGE RATING IN VOLTS THE AMOUNT OF VOLTAGE FOR WHICH THE HEATER IS DESIGNED,EXPRESSED IN VOLTS. 1B MODE REPLY 0 CYCVB 10POWER RATING IN WATTS,HEATER HEATER POWER RATING IN WATTS THE RATED POWER THAT THE HEATER CAN SAFELY CONSUME,MEASURED IN WATTS. 1B MODE REPLY 0 CYCWJ 10TIME IN SECONDS,DELAY DELAY TIME IN SECONDS A NUMERIC VALUE INDICATING THE ELAPSED TIME INTERVAL OF THE ITEM,EXPRESSED IN SECONDS. 2D AND 1B MODE REPLY22AJ271AC20 CYCXG 19NAME,PROGRAM,MANUFACTURERS MANUFACTURERS PROGRAM NAME THE MANUFACTURERS NAME OF THE PROGRAM THAT IS STORED ON THE ITEM. FULL TEXT WRITE-IN 0 CYCYA 12QUANTITY,POINT,TEST TEST POINT QUANTITY THE NUMBER OF TEST POINTS PROVIDED. 1A MODE REPLY 0 CYCZA 12QUANTITY,ACCOMMODATION,STEM STEM ACCOMMODATION QUANTITY THE NUMBER OF STEMS ACCOMMODATED ON THE ITEM. 1A MODE REPLY 0 CYDAD 19CONFIGURATION,PORT PORT CONFIGURATION THE CONFIGURATION OF THE PORTS ON THE ITEM VIEWED WITH THE STEM ACCOMMODATION AT THE TOP. SELECT REPLY CODE 10AD07 CYDBJ 04LENGTH,END,ENLARGED ENLARGED END LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE ENLARGED END OF THE ITEM,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CYDCJ 04DIAMETER,INSIDE,END,ENLARGED ENLARGED END INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ENLARGED END OF THE ITEM,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CYDDJ 04LENGTH,END,REDUCED REDUCED END LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE REDUCED END OF THE ITEM IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CYDEJ 04DIAMETER,OUTSIDE,END,REDUCED REDUCED END OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE REDUCED END OF THE ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CYDFB /D/ 10ERROR IN PERCENT,POSITION POSITION ERROR IN PERCENT THE ERROR OF THE PLOTTING SYSTEM IN FINAL POSITION AS COMPUTED AND EXPRESSED IN PERCENT. 1B MODE REPLY 0 CYDGJ 04HEIGHT,NOMINAL NOMINAL HEIGHT A NOMINAL MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN OBJECT,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 CYDHD /D/ 09MATERIAL,VENT VENT MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE VENT IS FABRICATED. SELECT REPLY CODE 10MA01 CYDJD /D/ 09MATERIAL,VALVE VALVE MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE VALVE IS FABRICATED. SELECT REPLY CODE 10MA01 CYDKD 10DENSITY RATING,DISK DISK DENSITY RATING THE MANUFACTURERS RATING FOR THE DENSITY OF THE DISK. SELECT REPLY CODE 10AL59 CYDLA 10TRACKS PER INCH TRACKS PER INCH THE NUMBER OF INFORMATION STORAGE TRACKS ON THE ITEM PER INCH. 1A MODE REPLY 0 CYDMD 08LOCATION,CABLE CABLE LOCATION INDICATES THE LOCATION OF THE CABLE. SELECT REPLY CODE 10AJ91 CYDNA 19MAKE/MODEL/YEAR MAKE/MODEL/YEAR THE ALPHA-NUMERIC USED TO IDENTIFY THE MAKE/MODEL/YEAR OF THE ITEM. 1A MODE REPLY 0 CYDPB 10RATING IN JOULES,ENERGY DISSIPATION,MAXIMUM MAXIMUM ENERGY DISSIPATION RATING IN JOULES THE MAXIMUM ENERGY,EXPRESSED IN JOULES,THAT CAN BE DISSIPATED FROM THE ITEM. 1B MODE REPLY 0 CYDQD 03DESIGNATION,PITCH,FACE FACE PITCH DESIGNATION THE PITCH DESIGNATION BY WHICH THE FACE OF THE ITEM IS IDENTIFIED. SELECT REPLY CODE 10AP76 CYDRA 12QUANTITY,FACE GROOVE/TOOTH FACE GROOVE/TOOTH QUANTITY THE NUMBER OF GROOVES OR TEETH INCLUDED ON THE FACE OF THE ITEM. 1A MODE REPLY 0 CYDSA 19ACTIVITY,CONTROL,DESIGN,ENGINE ENGINE DESIGN CONTROL ACTIVITY THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE GOVERNMENT AGENCY, INDUSTRIAL ORGANIZATION, OR OTHER ENTITY, WHICH CONTROLS THE DESIGN OF THE ENGINE. 1A MODE REPLY 0 CYDTA 19MODEL NUMBER FOR WHICH DESIGNED,ENGINE ENGINE MODEL NUMBER FOR WHICH DESIGNED THE COMBINED GROUPS OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE ENGINE FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 CYDUD 09MATERIAL,SHELL,OUTSIDE OUTSIDE SHELL MATERIAL THE CHEMICAL OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE OUTSIDE SHELL IS FABRICATED. SELECT REPLY CODE 10MA01 CYDVA 19ACTIVITY,CONTROL,DESIGN,PUMP PUMP DESIGN CONTROL ACTIVITY THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE GOVERNMENT AGENCY,INDUSTRIAL ORGANIZATION,OR OTHER ENTITY,WHICH CONTROLS THE DESIGN OF THE PUMP FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 CYDWA 19MODEL NUMBER FOR WHICH DESIGNED,PUMP PUMP MODEL NUMBER FOR WHICH DESIGNED THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE PUMP FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 CYDXA 19ACTIVITY,CONTROL,DESIGN,VALVE VALVE DESIGN CONTROL ACTIVITY THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE GOVERNMENT AGENCY,INDUSTRIAL ORGANIZATION,OR OTHER ENTITY,WHICH CONTROLS THE DESIGN OF THE VALVE. 1A MODE REPLY 0 CYDYA 19MODEL NUMBER FOR WHICH DESIGNED,VALVE VALVE MODEL NUMBER FOR WHICH DESIGNED THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE VALVE FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 CYDZD 09MATERIAL,SLIDE SLIDE MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE SLIDE IS FABRICATED. SELECT REPLY CODE 10MA01 CYEAD 09MATERIAL,SLEEVE SLEEVE MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE SLEEVE IS FABRICATED. SELECT REPLY CODE 10MA01 CYEBD 04SIZE,REEL,ACCOMMODATED ACCOMMODATED REEL SIZE DESIGNATES THE SIZE OF THE REEL THAT THE ITEM WILL ACCOMMODATE. SELECT REPLY CODE 10AF81 CYECD 18TYPE,INTERFACE INTERFACE TYPE INDICATES THE TYPE OF INTERFACE(S) AVAILABLE FOR INPUT/OUTPUT COMMUNICATIONS. SELECT REPLY CODE 10AE79 CYEDJ 04SIZE,MEMORY MEMORY SIZE DESIGNATES THE SIZE OF TEMPORARY DATA STORAGE AVAILABLE WITHIN THE ITEM. 1D AND 1B MODE REPLY12AG67 CYEEJ 10EXPANSION,MEMORY MEMORY EXPANSION THE TOTAL EXPANDABLE MEMORY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 CYEFA 12QUANTITY ACCOMMODATED,CARTRIDGE CARTRIDGE QUANTITY ACCOMMODATED THE NUMBER OF CARTRIDGE(S) THAT THE ITEM CAN ACCOMMODATE. 1A MODE REPLY 0 CYEGH 18TYPE PER SECTION,ELEMENT,RESISTANCE RESISTANCE ELEMENT TYPE PER SECTION INDICATES THE TYPE OF RESISTANCE ELEMENT AS DETERMINED BY ITS CONSTRUCTION PER SECTION. 2D MODE REPLY 22AH191AE09 CYEHJ 18TYPE AND RATING IN VOLTS,VOLTAGE,MOTOR MOTOR VOLTAGE TYPE AND RATING IN VOLTS INDICATES THE TYPE OF ELECTRICAL VOLTAGE AND RATING FOR WHICH THE MOTOR WAS DESIGNED,EXPRESSED IN VOLTS. 1D AND 1B MODE REPLY12AN87 CYEJH 10CURVE PER SECTION,TAPER,STANDARD STANDARD TAPER CURVE PER SECTION THE RATE OF CHANGE AND DISTRIBUTION OF RESISTANCE PER SECTION,IN RELATION TO THE ROTATION OF THE CONTROL SHAFT,WHICH ESTABLISHES A STANDARD TAPER CURVE DESIGNATED BY AN ALPHABETIC CHARACTER AND ACCEPTED FOR COMMON USAGE. 2D MODE REPLY 22AH192AF63 CYEKB 10RATIO,GEAR GEAR RATIO INDICATES THE RATIO OF THE OUTPUT GEAR TO THE INPUT GEAR. 1B MODE REPLY 0 CYELB 10TRAVEL,ANGULAR ANGULAR TRAVEL THE AMOUNT OF ANGULAR TRAVEL,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CYEMD 09MATERIAL,BLADE BLADE MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE BLADE IS FABRICATED. SELECT REPLY CODE 10MA01 CYEND 09MATERIAL,BASIC BASIC MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE BASIC MATERIAL IS FABRICATED. SELECT REPLY CODE 10MA01 CYEPA 19NUMBER,MODEL,AIRCRAFT AIRCRAFT MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE AIRCRAFT. 1A MODE REPLY 0 CYEQD 09MATERIAL,SHAFT SHAFT MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE SHAFT IS FABRICATED. SELECT REPLY CODE 10MA01 CYERD 09MATERIAL,GEAR GEAR MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE GEAR IS FABRICATED. SELECT REPLY CODE 10MA01 CYESJ 10RATING AND LOCATION,HARDNESS HARDNESS RATING AND LOCATION THE NUMERIC VALUE THAT REFLECTS THE HARDNESS OF AN ITEM WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE AND ITS LOCATION. 3D AND 1B MODE REPLY32AC261AC203AJ91 CYETJ 04DIAMETER,LARGEST,SHAFT SHAFT LARGEST DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHAFT,AND TERMINATES AT THE LARGEST CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CYEUD 08LOCATION ON SHAFT,GEAR GEAR LOCATION ON SHAFT INDICATES THE LOCATION OF THE GEAR ON THE SHAFT. SELECT REPLY CODE 10AJ91 CYEVJ 04LENGTH,SEGMENT,SHAFT,LONGER LONGER SHAFT SEGMENT LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE LONGER OF TWO SHAFT SEGMENTS. 2D AND 1B MODE REPLY21AA051AC20 CYEWJ 04SIZE,END,SHAFT SHAFT END SIZE DESIGNATES THE SIZE OF THE SHAFT END INCLUDED ON THE ITEM. 1D AND 1B MODE REPLY11AA05 CYEXD /D/ 09MATERIAL,AREA,VIEWING VIEWING AREA MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE VIEWING AREA IS FABRICATED. SELECT REPLY CODE 10MA01 CYEYA 12QUANTITY,GEAR GEAR QUANTITY THE NUMBER OF GEARS INCLUDED ON THE ITEM. 1A MODE REPLY 0 CYEZG 18TYPE,TUBE,ADSORPTION ADSORPTION TUBE TYPE INDICATES THE TYPE OF AIRBORNE CONTAMINATES/VAPORS(ADSORBATE)THE ADSORPTION TUBE IS DESIGNED TO TRAP. FULL TEXT WRITE-IN 0 CYFAJ 19DOCUMENT CONTROLLING AGENCY AND ANALYTICAL METHOD NUMBER DOCUMENT CONTROLLING AGENCY AND ANALYTICAL METHOD NUMBER THE DOCUMENT CONTROLLING AGENCY AND THE ANALYTICAL METHOD NUMBER THAT CONTAINS THE SPECIFICATIONS,STANDARDS,AND TECHNIQUES FOR PERFORMING AIR SAMPLING/MONITORING OF CONTAMINATES/VAPORS USING ADSORPTION TUBES. 1D AND 1B MODE REPLY13AP41 CYFBG 10WEIGHT AND TYPE,MATERIAL,ADSORBENT,LAYER/AREA,SAMPLE SAMPLE LAYER/AREA ADSORBENT MATERIAL WEIGHT AND TYPE THE MEASURED WEIGHT,EXPRESSED IN MILLIGRAMS,AND THE TYPE OF SAMPLE LAYER/AREA ADSORBENT MATERIAL. FULL TEXT WRITE-IN 0 CYFCG 10WEIGHT AND TYPE,MATERIAL,ADSORBENT,LAYER,REFERENCE/BLANK REFERENCE/BLANK LAYER ADSORBENT MATERIAL WEIGHT AND TYPE THE MEASURED WEIGHT,EXPRESSED IN MILLIGRAMS,AND THE TYPE OF REFERENCE/BLANK LAYER ADSORBENT MATERIAL. FULL TEXT WRITE-IN 0 CYFDJ A18TYPE AND QUANTITY,MATERIAL,PLUG,RETAINING RETAINING PLUG MATERIAL TYPE AND QUANTITY INDICATES THE TYPE(S) OF RETAINING PLUG MATERIAL AND NUMBER OF EACH TYPE INDICATED. 1D AND 1A MODE REPLY12AN27 CYFEA 19NUMBER,IDENTIFYING,HULL,SHIPS SHIPS HULL IDENTIFYING NUMBER AN IDENTIFYING NUMBER ASSIGNED BY THE CONTROLLING GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION AND USED BY THE MANUFACTURER TO IDENTIFY THE SHIPS HULL. 1A MODE REPLY 0 CYFFD /D/ 09MATERIAL,CUSHIONING CUSHIONING MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE CUSHIONING IS FABRICATED. SELECT REPLY CODE 10MA01 CYFGD 09MATERIAL,GRID GRID MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE GRID IS FABRICATED. SELECT REPLY CODE 10MA01 CYFHD 09MATERIAL,LINER LINER MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE LINER IS FABRICATED. SELECT REPLY CODE 10MA01 CYFJD 18TYPE,TESTED,OPTICAL FIBER OPTICAL FIBER TESTED TYPE INDICATES THE TYPE OF OPTICAL FIBER TO BE TESTED. SELECT REPLY CODE 10AK75 CYFKD 10WAVELENGTH IN NANOMETERS,OPTICAL PULSE OPTICAL PULSE WAVELENGTH IN NANOMETERS THE PULSE WAVELENGTH USED FOR THE MEASUREMENT OF FAULTS,OPTICAL LOSSES,SPLICING POSITION AND LOSSES,EXPRESSED IN NANOMETERS. SELECT REPLY CODE 10AP07 CYFLJ 04DISTANCE IN METERS,MAXIMUM MAXIMUM DISTANCE IN METERS THE MAXIMUM DISTANCE THAT CAN BE MEASURED WITH ACCURACY,EXPRESSED IN METERS. 1D AND 1B MODE REPLY11AA05 CYFMJ A19DESIGNATION,TIRE AND SIZE TIRE AND SIZE DESIGNATION THE COMMERCIAL DESIGNATION OF A TIRE BASED ON DIFFERENTIATED CHARACTERISTICS AND THE DIMENSIONS BY WHICH A TIRE IS IDENTIFIED. 1D AND 1A MODE REPLY12AN78 CYFNA 12QUANTITY,DRIVE DRIVE QUANTITY THE NUMBER OF DRIVES INCLUDED WITH THE ITEM. 1A MODE REPLY 0 CYFPJ 10CAPACITY,STORAGE,DATA DATA STORAGE CAPACITY THE LONG-TERM DATA STORAGE CAPABILITY OF THE ITEM SUCH AS HARD DRIVE, SSD, AND THE LIKE. 1D AND 1B MODE REPLY12AG67 CYFQD 04HEIGHT,DRIVE DRIVE HEIGHT THE HEIGHT OF THE DRIVE UNIT. SELECT REPLY CODE 10AK54 CYFRB 10TIME IN MILLISECONDS,ACCESS ACCESS TIME IN MILLISECONDS THE TIME REQUIRED TO POSITION THE ACCESS MECHANISM AT A SPECIFIED POSITION IN MILLISECONDS. 1B MODE REPLY 0 CYFSD /D/ 18TYPE AND QUANTITY,SECTOR SECTOR TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF SECTORING USED BY THE ITEM. SELECT REPLY CODE 10AJ55 CYFTB 10RATIO,RATE,INTERLEAVE INTERLEAVE RATE RATIO THE RATIO AT WHICH THE UNIT CAN SIMULTANEOUSLY PROCESS INCOMING/OUTGOING DATA.THE LARGER RELATIVE PORTION IS GIVEN.THE LOWER VALUE HAVING AN IMPLIED(NOT GIVEN)VALUE OF ONE. 1B MODE REPLY 0 CYFUB 10TRACKS PER INCH TRACKS PER INCH THE NUMBER OF RECORDING TRACKS PRODUCED PER INCH OF RADIAL MOVEMEMT OF A RECORDING HEAD ON THE ITEM. 1B MODE REPLY 0 CYFVD 11METHOD OF ANALYSIS METHOD OF ANALYSIS THE METHOD BY WHICH AN INSTRUMENT PERFORMS THE ACTUAL ASSAY(S) OF A SAMPLE/SPECIMEN. SELECT REPLY CODE 10AP77 CYFWD 19DATA NON-AVAILABILITY,RANGE,WAVELENGTH WAVELENGTH RANGE DATA NON-AVAILABILITY THE REASON FOR OMITTING THE WAVELENGTH RANGE DATA. SELECT REPLY CODE 10AP78 CYFXD 18TYPE,ELECTRODE ELECTRODE TYPE INDICATES THE TYPE OF ELECTRODE(S) EMPLOYED IN THE ITEM TO PRODUCE A SPECIFIC ION ASSAY OF A SAMPLE/SPECIMEN. SELECT REPLY CODE 10AF45 CYFYG 10RANGE,TEST/MEASUREMENT,ANALYSIS ANALYSIS TEST/MEASUREMENT RANGE THE BUILT IN TESTING RANGE FOR EACH TYPE OF TEST/ASSAY THAT THE ANALYTICAL INSTRUMENT IS CAPABLE OF PERFORMING. FULL TEXT WRITE-IN 0 CYFZG 04SIZE,TEST SAMPLE/SPECIMEN TEST SAMPLE/SPECIMEN SIZE THE AMOUNT,MASS,VOLUME,ETC.,OF A SAMPLE/SPECIMEN NEEDED BY THE ITEM TO RUN A COMPLETE ASSAY/TEST. FULL TEXT WRITE-IN 0 CYGAD /D/ 18TYPE,TEST SAMPLE/SPECIMEN TEST SAMPLE/SPECIMEN TYPE INDICATES THE TYPE OF SAMPLE/SPECIMEN THE ITEM IS CAPABLE OF ASCERTAINING QUALITATIVE ASSAY DETERMINATIONS. SELECT REPLY CODE 10AG63 CYGBD 19DEVICE,HOLDING,TEST SAMPLE/SPECIMEN TEST SAMPLE/SPECIMEN HOLDING DEVICE A DESIGNATED ITEM OR CONTAINER WHERE THE TEST SAMPLES/SPECIMENS ARE HELD IN OR ON THE ITEM. SELECT REPLY CODE 10AP80 CYGCD 19DEVICE,HOLDING,REAGENT/DILUENT REAGENT/DILUENT HOLDING DEVICE A DESIGNATED ITEM OR CONTAINER WHERE THE REAGENTS/DILUENTS ARE HELD IN OR ON THE ITEM. SELECT REPLY CODE 10AP80 CYGDJ A10THROUGHPUT PER HOUR THROUGHPUT PER HOUR THE NUMBER OF SAMPLES/SPECIMENS OR ASSAYS (TEST RESULTS) THAT THE ITEM IS CAPABLE OF PROCESSING IN ONE HOUR. 1D AND 1A MODE REPLY13AP79 CYGED 19DEVICE,DELIVERY,TEST SAMPLE/SPECIMEN TEST SAMPLE/SPECIMEN DELIVERY DEVICE A MEANS BY WHICH A SAMPLE/SPECIMEN IS INTRODUCED INTO THE ANALYTICAL AREA OF AN ITEM. SELECT REPLY CODE 10AP81 CYGFA 10CAPACITY,WAFFLE,UNIT UNIT WAFFLE CAPACITY THE NUMBER OF WAFFLES EACH BAKING UNIT IS CAPABLE OF PRODUCING HOURLY. 1A MODE REPLY 0 CYGGD 09MATERIAL,CABINET CABINET MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE CABINET IS FABRICATED. SELECT REPLY CODE 10MA01 CYGHG 19ORDERING,REPLACEMENT REPLACEMENT ORDERING A LISTING OF THOSE COMPONENTS WHICH HAVE A NATIONAL STOCK NUMBER AND MAY BE ORDERED SEPARATELY FOR REPLACEMENT. FULL TEXT WRITE-IN 0 CYGJD 09MATERIAL,COVERING COVERING MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE COVERING IS FABRICATED. SELECT REPLY CODE 10MA01 CYGKJ 10RATING,CURRENT,CLAMP CLAMP CURRENT RATING THE AMOUNT OF CURRENT FOR WHICH THE CLAMPS ARE RATED. 1D AND 1B MODE REPLY11AC30 CYGLD 01COLOR,INSULATION,CLAMP CLAMP INSULATION COLOR THE HUE OR TINT OF THE INSULATION ON THE CLAMP. SELECT REPLY CODE 10AD06 CYGMD 09MATERIAL,ROTOR,WIND SPEED WIND SPEED ROTOR MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE WIND SPEED ROTOR IS FABRICATED. SELECT REPLY CODE 10MA01 CYGND 09MATERIAL,TUBE TUBE MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE TUBE IS FABRICATED. SELECT REPLY CODE 10MA01 CYGPA 19ACTIVITY,CONTROL,DESIGN,MOTOR-PUMP MOTOR-PUMP DESIGN CONTROL ACTIVITY THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE GOVERNMENT AGENCY,INDUSTRIAL ORGANIZATION,OR OTHER ENTITY,WHICH CONTROLS THE DESIGN OF THE MOTOR-PUMP. 1A MODE REPLY 0 CYGQA 19MODEL NUMBER FOR WHICH DESIGNED,MOTOR-PUMP MOTOR-PUMP MODEL NUMBER FOR WHICH DESIGNED THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE MOTOR-PUMP FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 CYGRA 19LEGEND/INFORMATION,PUNCHED PUNCHED LEGEND/INFORMATION THE INFORMATION/LEGEND PUNCHED BY THE ITEM. 1A MODE REPLY 0 CYGSD /D/ 18TYPE,FORMAT FORMAT TYPE INDICATES THE TYPE OF FORMAT USED BY THE ITEM. SELECT REPLY CODE 10AN47 CYGTD 18TYPE,VANE VANE TYPE INDICATES THE TYPE OF VANE. SELECT REPLY CODE 10AK84 CYGUD 09MATERIAL,SHANK SHANK MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE SHANK IS FABRICATED. SELECT REPLY CODE 10MA01 CYGVJ 04THICKNESS ACCOMMODATED,SLIDE SLIDE THICKNESS ACCOMMODATED A MEASUREMENT OF THE SMALLEST DIMENSION OF THE SLIDE THE ITEM IS DESIGNED TO ACCOMMODATE,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CYGWJ 04SIZE,BUFFER BUFFER SIZE DESIGNATES THE MAXIMUM SIZE OF THE TEMPORARY DATA STORAGE CAPABILITY OF THE ITEM. 1D AND 1B MODE REPLY12AG67 CYGXD 18TYPE,PRINTING PRINTING TYPE INDICATES THE TYPE OF PRINT THAT IS AVAILABLE. SELECT REPLY CODE 10AK54 CYGYA 12QUANTITY,PATTERN,FLOW FLOW PATTERN QUANTITY THE NUMBER OF FL0W PATTERNS PROVIDED. 1A MODE REPLY 0 CYGZA 12QUANTITY,POSITION,SPOOL SPOOL POSITION QUANTITY THE NUMBER OF SPOOL POSITIONS PROVIDED. 1A MODE REPLY 0 CYHAD 18TYPE FOR WHICH DESIGNED,INSTRUMENT INSTRUMENT TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF INSTRUMENT THAT THE ITEM WILL BE USED WITH,AS SUGGESTED BY EITHER GOVERNMENT SPECIFICATION OR MANUFACTURER. SELECT REPLY CODE 10AP81 CYHBA 12QUANTITY,SPOOL SPOOL QUANTITY THE NUMBER OF SPOOLS PROVIDED. 1A MODE REPLY 0 CYHCG 19NAME,DESIGNATED,INDUSTRY INDUSTRY DESIGNATED NAME THE NAME OF THE ITEM,OTHER THAN A FUNCTIONAL OR APPLICATION NAME,THAT INDUSTRY HAS ASSIGNED. FULL TEXT WRITE-IN 0 CYHDF T10RANGE,MEASUREMENT,PH PH MEASUREMENT RANGE AN INDICATION OF THE PH MINIMUM AND MAXIMUM TESTING/MEASURING LIMITS OF THE ITEM. 1F MODE REPLY 0 CYHEJ 10RANGE,TEMPERATURE,OPERATING OPERATING TEMPERATURE RANGE THE MINUS AND/OR PLUS DEGREES OF TEMPERATURE THE ITEM CAN WITHSTAND WITHOUT GIVING ERRONEOUS ASSAY DATA. 2D AND 1B MODE REPLY21AB391AH08 CYHFJ /D/ 10RANGE,MEASUREMENT,CONCENTRATION CONCENTRATION MEASUREMENT RANGE INDICATES THE RANGE THAT THE ITEM CAN ACCURATELY MEASURE,A SPECIFIC ION CONCENTRATION THAT IT IS DESIGNED TO DETECT. 2D AND 1B MODE REPLY22AH141AC20 CYHGD 18TYPE,JUNCTION,REFERENCE REFERENCE JUNCTION TYPE INDICATES THE TYPE OF JUNCTION EMPLOYED IN THE ITEM,TO PREVENT UNWANTED ION INTERFERENCE. SELECT REPLY CODE 10AK95 CYHHD 18TYPE,ELEMENT,REFERENCE,INTERNAL INTERNAL REFERENCE ELEMENT TYPE INDICATES THE TYPE OF INTERNAL ELECTRODE ELEMENT EMPLOYED TO READ A SPECIFIC ION CONCENTRATION IN A SAMPLE/SPECIMEN OR SOLUTION. SELECT REPLY CODE 10AE98 CYHJD 18TYPE,CONNECTOR,ELECTRICAL ELECTRICAL CONNECTOR TYPE INDICATES THE TYPE OF ELECTRICAL LEAD CONNECTOR INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AE79 CYHKG 18TYPE AND MOLAR CONCENTRATION,SOLUTION,FILL FILL SOLUTION TYPE AND MOLAR CONCENTRATION INDICATES THE TYPE AND CONCENTRATION OF A SOLUTION NEEDED TO ACTIVATE THE ITEM. FULL TEXT WRITE-IN 0 CYHLD 09MATERIAL,POINT POINT MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE POINT IS FABRICATED. SELECT REPLY CODE 10MA01 CYHMG 18TYPE,TEST SAMPLE/SPECIMEN TEST SAMPLE/SPECIMEN TYPE INDICATES THE TYPE OF SAMPLE/SPECIMEN THE ITEM IS CAPABLE OF ASCERTAINING QUALITATIVE AND/OR QUANTITATIVE ASSAY DETERMINATIONS. FULL TEXT WRITE-IN 0 CYHND 04SIZE,DRIVE DRIVE SIZE DESIGNATES THE DRIVE SIZE INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AP82 CYHPD 04SIZE,DISK DISK SIZE DESIGNATES THE DISK SIZE INCLUDED WITH THE ITEM. SELECT REPLY CODE 10AP82 CYHQB 10RATE IN MEGABYTES PER SECOND,TRANSFER TRANSFER RATE IN MEGABYTES PER SECOND THE RATE THAT INFORMATION IS TRANSFERRED FROM ONE SOURCE TO ANOTHER,EXPRESSED IN MEGABYTES PER SECOND. 1B MODE REPLY 0 CYHRD 19CAPABILITY,DISPLAY,HIGHEST HIGHEST DISPLAY CAPABILITY INDICATES THE HIGHEST MONITOR DISPLAY CAPABILITY. SELECT REPLY CODE 10AE79 CYHSB 04SIZE IN INCHES,DISPLAY,DIAGONAL DIAGONAL DISPLAY SIZE IN INCHES THE LENGTH OF A STRAIGHT LINE THAT RUNS FROM ONE CORNER OF THE DISPLAY SCREEN TO THE OTHER CORNER,EXPRESSED IN INCHES. 1B MODE REPLY 0 CYHTD 18TYPE,FORMAT,TAPE,PHYSICAL PHYSICAL TAPE FORMAT TYPE INDICATES THE TYPE OF PHYSICAL TAPE FORMAT USED. SELECT REPLY CODE 10AJ79 CYHUD 18TYPE,DEVICE,INPUT INPUT DEVICE TYPE INDICATES THE TYPE OF DEVICE USED FOR ENTERING INFORMATION INTO THE COMPUTER. SELECT REPLY CODE 10AN47 CYHVD 18TYPE,DEVICE,OUTPUT OUTPUT DEVICE TYPE INDICATES THE TYPE OF DEVICE USED FOR DISPLAYING INFORMATION ON THE COMPUTER. SELECT REPLY CODE 10AK54 CYHWJ X19NUMBER,MANUFACTURER AND PART,JUNCTION BOX JUNCTION BOX MANUFACTURER AND PART NUMBER THE 5-POSITION COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE AND PART NUMBER FOR EACH DIFFERENT TYPE OF JUNCTION BOX COMPRISING THE ASSEMBLY. 1D AND 1A MODE REPLY15AB08 CYHXA 19ACTIVITY,CONTROL,DESIGN,VEHICLE VEHICLE DESIGN CONTROL ACTIVITY THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE GOVERNMENT AGENCY,INDUSTRIAL ORGANIZATION,OR OTHER ENTITY,WHICH CONTROLS THE DESIGN OF THE VEHICLE. 1A MODE REPLY 0 CYHYA 03DESIGNATOR,IDENTIFICATION,VEHICLE VEHICLE IDENTIFICATION DESIGNATOR THE NAME OR COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH IDENTIFY THE SPECIFIC VEHICLE. 1A MODE REPLY 0 CYHZA 19YEAR(S),VEHICLE VEHICLE YEAR(S) THE FOUR (4) DIGIT NUMBER INDICATING THE PRODUCTION YEAR(S) OF THE VEHICLE. 1A MODE REPLY 0 CYJAJ 04DISTANCE BETWEEN TERMINAL BOARDS,MOUNTING MOUNTING DISTANCE BETWEEN TERMINAL BOARDS THE DISTANCE THE TERMINAL BOARDS ARE MOUNTED APART(HORIZONTAL OR VERTICAL). 1D AND 1B MODE REPLY11AA05 CYJBA 19ACTIVITY,CONTROL,DESIGN,END ITEM END ITEM DESIGN CONTROL ACTIVITY THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE GOVERNMENT AGENCY,INDUSTRIAL ORGANIZATION,OR OTHER ENTITY,WHICH CONTROLS THE DESIGN OF THE END ITEM. 1A MODE REPLY 0 CYJCA 19YEAR(S),END ITEM END ITEM YEAR(S) THE FOUR (4) DIGIT NUMBER INDICATING THE PRODUCTION YEAR(S) OF THE END ITEM. 1A MODE REPLY 0 CYJDA 03DESIGNATOR,IDENTIFICATION,END ITEM END ITEM IDENTIFICATION DESIGNATOR THE NAME OR COMBINED GROUP OF LETTERS,AND/OR SYMBOLS WHICH IDENTIFY THE SPECIFIC END ITEM. 1A MODE REPLY 0 CYJEJ 10CAPACITY IN BTU PER HOUR,COOLING COOLING CAPACITY IN BTU PER HOUR THE CAPACITY OF THE ITEM TO COOL,EXPRESSED IN BRITISH THERMAL UNITS PER HOUR. 1D AND 1B MODE REPLY11AC20 CYJFA 10CAPACITY,CADAVER CADAVER CAPACITY THE NUMBER OF CADAVERS THE UNIT WILL HOLD. 1A MODE REPLY 0 CYJGD 18TYPE,PATTERN,COVERAGE COVERAGE PATTERN TYPE INDICATES THE CONFIGURATION OF THE COVERAGE PATTERN. SELECT REPLY CODE 10AD07 CYJHD 07CONNECTION(S),CABLE,GROUNDING GROUNDING CABLE CONNECTION(S) THE FREE END CONNECTION ON THE CABLE BY WHICH IT IS GROUNDED. SELECT REPLY CODE 10AN89 CYJJA 10TRACKS PER HEAD,RECORDING RECORDING TRACKS PER HEAD THE NUMBER OF TRACKS USED FOR RECORDING AND PLAYBACK. 1A MODE REPLY 0 CYJKJ 04WIDTH IN INCHES,TAPE,ACCOMMODATED ACCOMMODATED TAPE WIDTH IN INCHES DESIGNATES THE WIDTH OF THE TAPE THAT THE ITEM CAN ACCOMMODATE,EXPRESSED IN INCHES. 1D AND 1B MODE REPLY13AJ79 CYJLJ 10SPEED IN INCHES PER SECOND,READ/WRITE READ/WRITE SPEED IN INCHES PER SECOND THE SPEED THAT INFORMATION CAN BE WRITTEN ON OR READ OFF THE ITEM,EXPRESSED IN INCHES PER SECOND. 1D AND 1B MODE REPLY13AB44 CYJMA 19YEAR(S),ENGINE ENGINE YEAR(S) THE FOUR (4) DIGIT NUMBER INDICATING THE PRODUCTION YEAR(S) OF THE ENGINE. 1A MODE REPLY 0 CYJND 19COMPONENTS,FURNISHED FURNISHED COMPONENTS THE PRINCIPAL PARTS SUPPLIED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE. SELECT REPLY CODE 10AB28 CYJPJ /D/ 10IMPEDANCE RATING IN OHMS,INPUT INPUT IMPEDANCE RATING IN OHMS THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) WHICH THE ITEM OFFERS TO THE ADMITTANCE OF AN ENTERING FLOW OF ALTERNATING CURRENT,EXPRESSED IN OHMS. 1D AND 1B MODE REPLY11AC20 CYJQA 19NUMBER,MODEL,PUMP PUMP MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE PUMP. 1A MODE REPLY 0 CYJRD /D/ 18TYPE,DIAPHRAGM,HORN HORN DIAPHRAGM TYPE INDICATES THE TYPE OF HORN USED WITH THE DIAPHRAGM. SELECT REPLY CODE 10AB75 CYJSD 09MATERIAL,PANEL PANEL MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE PANEL IS FABRICATED. SELECT REPLY CODE 10MA01 CYJTA /D/ 04SIZE,NEMA NEMA SIZE DESIGNATES THE NATIONAL ELECTRICAL MANUFASTURERS ASSOCIATION SIZE. 1A MODE REPLY 0 CYJUD 09MATERIAL,O-RING O-RING MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE O-RING IS FABRICATED. SELECT REPLY CODE 10MA01 CYJVJ 10PRESSURE,SUPPLY SUPPLY PRESSURE THE PRESSURE AT WHICH THE ITEM OPERATES. 1D AND 1B MODE REPLY11AN71 CYJWD 18TYPE,CONFIGURATION,COIL COIL CONFIGURATION TYPE INDICATES THE TYPE OF COIL CONFIGURATION. SELECT REPLY CODE 10AK33 CYJXB 10RATING IN MA,CURRENT,RATED RATED CURRENT RATING IN MA THE ELECTRICAL RATED CURRENT RATING,EXPRESSED IN MILLIAMPERES. 1B MODE REPLY 0 CYJYA 10DOSAGE IN NANOSECONDS,X-RAY X-RAY DOSAGE IN NANOSECONDS THE AVERAGE X-RAY DOSAGE,EXPRESSED IN NANOSECONDS. 1A MODE REPLY 0 CYJZD /D/ 09MATERIAL,COMPONENT,WIND DIRECTION WIND DIRECTION COMPONENT MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE WIND DIRECTION COMPONENT IS FABRICATED. SELECT REPLY CODE 10MA01 CYKAJ 04WIDTH,OVERALL,ASSEMBLY,CABLE CABLE ASSEMBLY OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CABLE ASSEMBLY,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CYKBG 10RATING,ACCURACY ACCURACY RATING A MEASUREMENT OF ARC TIME AND DEGREES OF SPECIFIC LATITUDE. FULL TEXT WRITE-IN 0 CYKCJ A18TYPE AND QUANTITY,SECTOR SECTOR TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF SECTORING USED BY THE ITEM. 1D AND 1A MODE REPLY13AJ55 CYKDJ /D/ 04LENGTH OF THE CABLE DISPENSER,NOMINAL NOMINAL LENGTH OF THE CABLE DISPENSER A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE CABLE DISPENSER,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CYKED /D/ 18TYPE,HEAD,SCREW SCREW HEAD TYPE INDICATES THE TYPE OF HEAD ON THE SCREW PROVIDED. SELECT REPLY CODE 10AE98 CYKFD 18TYPE,JEWEL JEWEL TYPE INDICATES THE TYPE OF JEWEL PROVIDED. SELECT REPLY CODE 10AK39 CYKGD 18TYPE,KEY KEY TYPE INDICATES THE TYPE OF KEYS USED. SELECT REPLY CODE 10AC58 CYKHJ /D/ 04LENGTH OF THE MINE SWEEPING CABLE,NOMINAL NOMINAL LENGTH OF THE MINE SWEEPING CABLE A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE MINE SWEEPING CABLE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CYKJD 16STYLE,BOX BOX STYLE THE STYLE INDICATING THE CONFIGURATION OF THE BOX. SELECT REPLY CODE 10AK54 CYKKJ /D/ 04DIAMETER OF THE MINE SWEEPING CABLE,NOMINAL NOMINAL DIAMETER OF THE MINE SWEEPING CABLE THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MINE SWEEPING CABLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CYKLJ /D/ 04DIAMETER OF THE CABLE DISPENSER,EXTERNAL,NOMINAL NOMINAL EXTERNAL DIAMETER OF THE CABLE DISPENSER THE NOMINAL EXTERNAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CABLE DISPENSER,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CYKMJ 10CAPACITY IN BTU PER HOUR,HEATING HEATING CAPACITY IN BTU PER HOUR THE CAPACITY OF THE ITEM TO HEAT,EXPRESSED IN BRITISH THERMAL UNITS PER HOUR. 1D AND 1B MODE REPLY11AC20 CYKNA 04SIZE FOR WHICH DESIGNED,REEL REEL SIZE FOR WHICH DESIGNED DESIGNATES THE SIZE OF THE REEL FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 CYKPA 19DESIGN CONTROL ACTIVITY,FAUCET FAUCET DESIGN CONTROL ACTIVITY THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE GOVERNMENT AGENCY,INDUSTRIAL ORGANIZATION,OR OTHER ENTITY,WHICH CONTROLS THE DESIGN OF THE FAUCET. 1A MODE REPLY 0 CYKQA 19NUMBER FOR WHICH DESIGNED,MODEL,FAUCET FAUCET MODEL NUMBER FOR WHICH DESIGNED THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE FAUCET FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 CYKRJ 04RADIUS,TOP TOP RADIUS A MEASUREMENT OF THE BEND DISTANCE OF THE ITEM FROM THE TOP TO THE AXIS. 2D AND 1B MODE REPLY21AA051AC20 CYKSB 04ANGLE IN DEG,TOP TOP ANGLE IN DEG THE ANGLE FORMED BY THE ANGULAR PORTION OF THE ITEM,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CYKTA 19NUMBER,SERIAL,ENGINE ENGINE SERIAL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED SERIAL NUMBER OF THE ENGINE. 1A MODE REPLY 0 CYKUJ /D/ 04DIAMETER,STUD,LOCATING LOCATING STUD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A LOCATING STUD,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CYKVJ /D/ 04DIAMETER,HOLE,BUSHING,DRILL DRILL BUSHING HOLE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A DRILL BUSHING HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CYKWD 18TYPE,CONSTRUCTION,ROTOR ROTOR CONSTRUCTION TYPE INDICATES THE TYPE OF ROTOR CONSTRUCTION. SELECT REPLY CODE 10AC69 CYKXB 04ANGLE IN DEG,STEP STEP ANGLE IN DEG THE STEP ANGLE,EXPRESSED IN DEGREES. 1B MODE REPLY 0 CYKYA 10STEPS PER REVOLUTION STEPS PER REVOLUTION THE NUMBER OF STEPS PER MOTOR REVOLUTION. 1A MODE REPLY 0 CYKZB /D/ 19INERTIA,ROTOR ROTOR INERTIA THE AMOUNT OF FORCE REQUIRED TO START,STOP OR CHANGE ROTOR DIRECTION,EXPRESSED IN INCH-OUNCE PER SQUARE SECOND. 1B MODE REPLY 0 CYLAJ 04LENGTH,AREA,VIEWING VIEWING AREA LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE VIEWING AREA,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CYLBJ 04WIDTH,AREA,VIEWING VIEWING AREA WIDTH A MEASUREMENT OF THE WIDTH OF THE VIEWING AREA,IN DISTINCTION FROM LENGTH. 2D AND 1B MODE REPLY21AA051AC20 CYLCA 10BRIGHTNESS AT RATED VOLTAGE,CHARACTER CHARACTER BRIGHTNESS AT RATED VOLTAGE THE BRIGHTNESS OF THE PROJECTED CHARACTERS,EXPRESSED IN FOOTLAMBERTS. 1A MODE REPLY 0 CYLDJ 04DISTANCE,VIEWING VIEWING DISTANCE THE DISTANCE FROM THE DISPLAY AREA THE MESSAGE MAY BE CLEARLY VIEWED. 2D AND 1B MODE REPLY21AA051AC20 CYLED 09MATERIAL,FIN FIN MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE FIN IS FABRICATED. SELECT REPLY CODE 10MA01 CYLFD 18TYPE FOR WHICH DESIGNED,REFRIGERANT,COIL COIL REFRIGERANT TYPE FOR WHICH DESIGNED INDICATES THE TYPE REFRIGERANT THE COIL IS DESIGNED TO USE. SELECT REPLY CODE 10AB75 CYLGD 18TYPE,ARRANGEMENT,FIN FIN ARRANGEMENT TYPE INDICATES THE TYPE ARRANGEMENT OF THE FINS ON THE ITEM. SELECT REPLY CODE 10AK33 CYLHD 18TYPE,CONSTRUCTION/ARRANGEMENT,COIL COIL CONSTRUCTION/ARRANGEMENT TYPE INDICATES THE TYPE CONSTRUCTION AND/OR ARRANGEMENT OF THE COIL. SELECT REPLY CODE 10AC66 CYLJD 18TYPE,SYSTEM,CLEANING CLEANING SYSTEM TYPE INDICATES THE TYPE OF CLEANING SYSTEM PROVIDED. SELECT REPLY CODE 10AM54 CYLKJ /D/ 04WIDTH,BLANKET,INSIDE INSIDE BLANKET WIDTH THE INSIDE BLANKET MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 CYLLJ /D/ 04DEPTH,BLANKET,INSIDE INSIDE BLANKET DEPTH THE INSIDE BLANKET MEASUREMENT BETWEEN SPECIFIED POINTS OF AN ITEM,IN DISTINCTION FROM HEIGHT. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 CYLMJ /D/ 04WIDTH,OVERALL,CONVEYOR CONVEYOR OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CONVEYOR,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CYLNA /D/ 12QUANTITY PER HOUR,BUN,RATE RATE BUN QUANTITY PER HOUR THE RATED NUMBER OF BUNS(ROLLS)HEATED PER HOUR. 1A MODE REPLY 0 CYLPA /D/ 10CAPACITY PER HOUR,BROILING,HAMBURGER HAMBURGER BROILING CAPACITY PER HOUR THE CAPACITY OF HAMBURGERS(4 OZ)THE UNIT WILL BROIL PER HOUR. 1A MODE REPLY 0 CYLQJ /D/ 04LENGTH,BRIDLE BRIDLE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A BRIDLE,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CYLRJ 04LENGTH,ANCHOR ANCHOR LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ANCHOR,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CYLSJ /D/ 04SIZE,SWIVEL SWIVEL SIZE DESIGNATES THE SIZE OF THE SWIVEL. 1D AND 1B MODE REPLY11AA05 CYLTA 12QUANTITY,DOOR,STORAGE STORAGE DOOR QUANTITY THE NUMBER OF STORAGE DOORS PROVIDED. 1A MODE REPLY 0 CYLUA 10CAPACITY,PAN,STORAGE,FOOD FOOD STORAGE PAN CAPACITY THE NUMBER OF FOOD PANS THE ITEM WILL HOLD. 1A MODE REPLY 0 CYLVJ 04LENGTH,CONDUIT CONDUIT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE CONDUIT,IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CYLWJ 13THREAD DIAMETER,NOMINAL,CONNECTION,SUPPLY,FUEL FUEL SUPPLY CONNECTION NOMINAL THREAD DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE FUEL SUPPLY CONNECTION IN PLAIN VIEW WHICH WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD. 1D AND 1B MODE REPLY11AA05 CYLXB /D/ 10RATING IN DECIBELS,SUPPRESSION,NOISE NOISE SUPPRESSION RATING IN DECIBELS THE NOISE QUIETING ABILITY OF THE ITEM,EXPRESSED IN DECIBELS. 1B MODE REPLY 0 CYLYD 04SIZE ACCOMMODATED,TIE,CABLE CABLE TIE SIZE ACCOMMODATED THE PHYSICAL BULK(BIGNESS)OF THE CABLE TIE THE ITEM IS DESIGNED TO ACCOMMODATE. SELECT REPLY CODE 10AN47 CYLZB 12QUANTITY,CONTENT,CONTAINER,PRIMARY,CAPSULE CAPSULE PRIMARY CONTAINER CONTENT QUANTITY A NUMERIC VALUE OF THE VOLUME,FORM,OR DOSAGE WITHIN EACH CAPSULE PRIMARY CONTAINER. 1B MODE REPLY 0 CYMAJ 10CAPACITY PER HOUR,DISPENSING,MINIMUM MINIMUM DISPENSING CAPACITY PER HOUR THE MINIMUM DISPENSING AMOUNT PER HOUR OF THE ITEM. 1D AND 1B MODE REPLY12AG67 CYMBJ A18TYPE AND QUANTITY,ELEMENT,ROLLING ROLLING ELEMENT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF ROLLING ELEMENTS FOR MOVING THE ITEM. 1D AND 1A MODE REPLY13AA78 CYMCJ A10RESOLUTION,DISPLAY DISPLAY RESOLUTION INDICATES THE DISPLAY RESOLUTION,EXPRESSED IN THE NUMBER OF PIXELS PER HORIZONTAL LINE BY THE NUMBER OF LINES ON A VERTICAL PLANE. 1D AND 1A MODE REPLY13AA38 CYMDJ 04THICKNESS,WALL,TUBE,MAIN BODY MAIN BODY TUBE WALL THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE MAIN BODY TUBE WALL,IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CYMEJ 04DIAMETER,OUTSIDE,TUBE,MAIN BODY MAIN BODY TUBE OUTSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MAIN BODY TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CYMFH 19FINISH AND LOCATION,SURFACE SURFACE FINISH AND LOCATION AN ADDITIONAL FINISHING PROCESS BY WHICH THE SURFACE OF AN ITEM IS ALTERED IN RESPECT TO POLISHING,GRINDING,DIPPING AND THE LIKE,AND ITS LOCATION. 2D MODE REPLY 23AK393AJ91 CYMGJ 10INGREDIENT AND STRENGTH,ACTIVE ACTIVE INGREDIENT AND STRENGTH THE ACTIVE INDREDIENT(S) AND STRENGTH IN A PHARMACEUTICAL PREPARATION RECOGNIZED AS HAVING THERAPEUTIC VALUE(S). 2D AND 1B MODE REPLY25AG542AG53 CYMHJ 04HEIGHT,CROSS CROSS HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE CROSS,IN DISTINCTION FROM DEPTH. 1D AND 1B MODE REPLY11AA05 CYMJG /D/ 12QUANTITY AND COMPONENTS,TEST KIT TEST KIT QUANTITY AND COMPONENTS THE NUMBER OF EACH COMPONENT AND THE NAME. FULL TEXT WRITE-IN 0 CYMKJ 04WIDTH,RUDDER RUDDER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A RUDDER,IN DISTINCTION FROM THICKNESS. 2D AND 1B MODE REPLY21AA051AC20 CYMLJ 04HEIGHT,RUDDER RUDDER HEIGHT THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF A RUDDER. 2D AND 1B MODE REPLY21AA051AC20 CYMMJ 04THICKNESS AT LEADING EDGE,RUDDER RUDDER THICKNESS AT LEADING EDGE A MEASUREMENT OF THE SMALLEST DIMENSION OF A RUDDER AT THE LEADING EDGE,IN DISTINCTION FROM WIDTH OR HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CYMNJ 04THICKNESS AT TRAILING EDGE,RUDDER RUDDER THICKNESS AT TRAILING EDGE A MEASUREMENT OF THE SMALLEST DIMENSION OF A RUDDER AT THE TRAILING EDGE,IN DISTINCTION FROM WIDTH OR HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CYMPD 19MEDIA,TEST TEST MEDIA THE MEDIA IN WHICH THE TEST IS PERFORMED. SELECT REPLY CODE 10AN91 CYMQH /D/ 17SURFACE TREATMENT AND LOCATION SURFACE TREATMENT AND LOCATION THE METALLIC, NONMETALLIC, AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED, DIPPED, AND/OR COATED, AND ITS LOCATION.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACES AND CANNOT BE WIPED OFF. PLEASE USE MRC SFTT WITH ISAC CODING IN PLACE OF THIS DISCONTINUED MRC. 2D MODE REPLY 26SF013AN73 CYMRD 14SHAPE,BLADE BLADE SHAPE THE PHYSICAL CONFIGURATION OF THE BLADE. SELECT REPLY CODE 10AD07 CYMSG 19BREAKDOWN WITHIN EACH TEST KIT,COMPONENT COMPONENT BREAKDOWN WITHIN EACH TEST KIT THE NUMBER AND NAME OF EACH COMPONENT WITHIN THE TEST KIT. FULL TEXT WRITE-IN 0 CYMTG 19STRENGTH IN SYSTEM,OVERALL OVERALL STRENGTH IN SYSTEM THE OVERALL STRENGTH OF THE ACTIVE INGREDIENT CONTAINED IN THE SYSTEM. FULL TEXT WRITE-IN 0 CYMUG 04SIZE,SYSTEM SYSTEM SIZE DESIGNATES THE OVERALL SYSTEM SIZE. FULL TEXT WRITE-IN 0 CYMVJ 10SHIFT IN DEG,PHASE PHASE SHIFT IN DEG THE PHASE SHIFT OF THE INPUT SIGNAL, WITH RESPECT TO THE OUTPUT SIGNAL, OF THE ITEM, EXPRESSED IN DEGREES. 2D AND 1B MODE REPLY22AG041AC20 CYMWJ 04WIDTH,PULSE PULSE WIDTH THE DURATION OF THE FORMED PULSE, EXPRESSED IN MICROSECONDS. 1D AND 1B MODE REPLY11AC20 CYMXJ 10REPETITION,PULSE PULSE REPETITION THE RATE (REPETITION) AT WHICH THE PULSE REPEATS ITSELF, EXPRESSED IN PULSES PER SECOND (PPS). 1D AND 1B MODE REPLY11AC20 CYMYJ 10TIME,RISE,PULSE PULSE RISE TIME THE RATE AT WHICH THE PULSE REACHES ITS PEAK, EXPRESSED IN MICROSECONDS. 1D AND 1B MODE REPLY11AC20 CYMZJ 10TIME,FALL,PULSE PULSE FALL TIME THE RATE AT WHICH THE PULSE DECREASES FROM ITS PEAK, EXPRESSED IN MICROSECONDS. 1D AND 1B MODE REPLY11AC20 CYNAJ 10RATED AT IDLE,RANGE,SPEED SPEED RANGE RATED AT IDLE THE RATED SPEED AT IDLE FOR WHICH THE ITEM HAS BEEN TESTED FOR PERFORMANCE. 1D AND 1B MODE REPLY11AA34 CYNBJ 10RATING FULL LOAD,RANGE,SPEED SPEED RANGE RATING FULL LOAD THE MINIMUM AND/OR MAXIMUM SPEED RANGE LIMITS/FULL LOAD FOR WHICH THE ITEM HAS BEEN TESTED FOR PERFORMANCE. 1D AND 1B MODE REPLY11AA34 CYNCD 09MATERIAL,BOWL BOWL MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE BOWL IS FABRICATED. SELECT REPLY CODE 10MA01 CYNDA /D/ 04SIZE,BURNER BURNER SIZE THE ALPHA/NUMERIC OR SYMBOL USED TO DENOTE THE BURNER SIZE. 1A MODE REPLY 0 CYNED 09MATERIAL,HEAD HEAD MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE HEAD IS FABRICATED. SELECT REPLY CODE 10MA01 CYNFB 10RATING,HORSEPOWER,MOTOR MOTOR HORSEPOWER RATING AN INDICATION OF THE RATED HORSEPOWER OF THE MOTOR. 1B MODE REPLY 0 CYNGD /D/ 18TYPE,SEQUENCE,CONTROL CONTROL SEQUENCE TYPE INDICATES THE TYPE OF CONTROL SEQUENCE PROVIDED. SELECT REPLY CODE 10AC58 CYNHJ 04DIAMETER,INSIDE,NOMINAL,FIRST END,PIPE/TUBE PIPE/TUBE FIRST END NOMINAL INSIDE DIAMETER A FIRST END DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE NOMINAL INSIDE DIAMETER OF THE PIPE/TUBE. 1D AND 1B MODE REPLY11AA05 CYNJD 18TYPE,TECHNOLOGY TECHNOLOGY TYPE INDICATES THE TYPE OF TECHNOLOGY USED WITH THE ITEM. SELECT REPLY CODE 10AJ21 CYNKJ 04DIAMETER,OUTSIDE,NOMINAL,FIRST END,PIPE/TUBE PIPE/TUBE FIRST END NOMINAL OUTSIDE DIAMETER A FIRST END DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE NOMINAL OUTSIDE DIAMETER OF THE PIPE/TUBE. 1D AND 1B MODE REPLY11AA05 CYNLJ 04DIAMETER,INSIDE,NOMINAL,SECOND END,PIPE/TUBE PIPE/TUBE SECOND END NOMINAL INSIDE DIAMETER A SECOND END DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE NOMINAL INSIDE DIAMETER OF THE PIPE/TUBE. 1D AND 1B MODE REPLY11AA05 CYNMJ 04DIAMETER,OUTSIDE,NOMINAL,SECOND END,PIPE/TUBE PIPE/TUBE SECOND END NOMINAL OUTSIDE DIAMETER A SECOND END DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE NOMINAL OUTSIDE DIAMETER OF THE PIPE/TUBE. 1D AND 1B MODE REPLY11AA05 CYNNJ 04LENGTH,LEG,NOMINAL NOMINAL LEG LENGTH A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE LEG, IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CYNPJ 10TEMPERATURE,BURST BURST TEMPERATURE A RATING WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AT WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY11AB36 CYNQJ 04SIZE,DISK DISK SIZE DESIGNATES THE SIZE OF THE DISK. 1D AND 1B MODE REPLY11AA05 CYNRD 18TYPE,PLOTTER PLOTTER TYPE INDICATES THE TYPE OF PLOTTING METHOD OF THE UNIT. SELECT REPLY CODE 10AK54 CYNSA 19NAME,FONT FONT NAME THE NAME OF THE PRINT TYPE (FONT) DESIGNATED BY THE MANUFACTURER. 1A MODE REPLY 0 CYNTD 05DIRECTION,PRINT PRINT DIRECTION THE DIRECTION IN WHICH THE PRINT IS PLACED ON THE MEDIAN. SELECT REPLY CODE 10AJ91 CYNUJ 04SIZE,ENGINE ENGINE SIZE DESIGNATES THE SIZE OF THE ENGINE. 1D AND 1B MODE REPLY13AJ40 CYNVD /D/ 18TYPE ELECTRICAL INTERFERENCE SHIELDING PROVIDED TYPE ELECTRICAL INTERFERENCE SHIELDING PROVIDED INDICATES THE TYPE OF ELECTRICAL INTERFERENCE THE SHIELD WILL SUPPRESS. SELECT REPLY CODE 10AE41 CYNWJ /D/ 10SPEED,PRINT PRINT SPEED DESIGNATES THE PRINTING RATE OF THE ITEM. 1D AND 1B MODE REPLY13AB44 CYNXA 19ACTIVITY,CONTROL,DESIGN,ENGINE/COMPRESSOR ENGINE/COMPRESSOR DESIGN CONTROL ACTIVITY THE COMMERCIAL AND GOVERNMENT (CAGE) CODE OF THE GOVERNMENT AGENCY, INDUSTRIAL ORGANIZATION, OR OTHER ENTITY, WHICH CONTROLS THE DESIGN OF THE ENGINE/COMPRESSOR. 1A MODE REPLY 0 CYNYA 19NUMBER FOR WHICH DESIGNED,MODEL,ENGINE/COMPRESSOR ENGINE/COMPRESSOR MODEL NUMBER FOR WHICH DESIGNED THE COMBINED GROUP OF LETTERS, NUMERALS, AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE ENGINE/COMPRESSOR FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 CYNZA 19NUMBER FOR WHICH DESIGNED,SERIES AND/OR SERIAL,TYPE,CODE CODE TYPE SERIES AND/OR SERIAL NUMBER FOR WHICH DESIGNED THE DESIGNATION WHICH DIFFERENTIATES BETWEEN ITEMS OF THE SAME MODEL NUMBER. 1A MODE REPLY 0 CYPAJ 04DIAMETER,ROTOR ROTOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A ROTOR, AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CYPBA 19COUPLING FOR WHICH DESIGNED,MODEL OR SIZE MODEL OR SIZE COUPLING FOR WHICH DESIGNED THE COMBINED GROUP OF LETTERS, NUMBERS, AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED NUMBER MODEL OR SIZE COUPLING FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 CYPCJ /D/ 04LENGTH OF THE GUIDANCE CABLE,NOMINAL NOMINAL LENGTH OF THE GUIDANCE CABLE A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE GUIDANCE CABLE, IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 CYPDJ /D/ 04DIAMETER OF THE GUIDANCE CABLE,NOMINAL NOMINAL DIAMETER OF THE GUIDANCE CABLE THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GUIDANCE CABLE, AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CYPEJ 04DIAMETER ACCOMMODATED,OUTSIDE,PIPE PIPE OUTSIDE DIAMETER ACCOMMODATED A MEASUREMENT OF THE OUTSIDE DIAMETER OF THE PIPE ACCOMMODATED. 1D AND 1B MODE REPLY11AA05 CYPFD 18TYPE,PRESSURE,DELIVERY DELIVERY PRESSURE TYPE INDICATES THE TYPE OF DELIVERY PRESSURE. SELECT REPLY CODE 10AC58 CYPGJ 10PRESSURE,DELIVERY,PRESET PRESET DELIVERY PRESSURE THE PREDETERMINED SETTING AT WHICH AN ITEM IS DESIGNED TO OPERATE. 1D AND 1B MODE REPLY12AG20 CYPHJ 13THREAD SIZE,NOMINAL,FITTING,INLET INLET FITTING NOMINAL THREAD SIZE A NOMINAL DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE INLET FITTING THREAD SIZE. 1D AND 1B MODE REPLY11AA05 CYPJA 19NUMBER,CGA,CONNECTION,FITTING,INLET INLET FITTING CONNECTION CGA NUMBER A DESIGNATION NUMBER ASSIGNED TO THE INLET FITTING CONNECTION, IN ACCORDANCE WITH THE COMPRESSED GAS ASSOCIATION. 1A MODE REPLY 0 CYPKD 18TYPE,CONNECTION,FITTING,OUTLET OUTLET FITTING CONNECTION TYPE INDICATES THE TYPE OF OUTLET FITTING CONNECTION PROVIDED. SELECT REPLY CODE 10AB76 CYPLJ 13THREAD SIZE,NOMINAL,FITTING,OUTLET OUTLET FITTING NOMINAL THREAD SIZE A NOMINAL DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE OUTLET FITTING THREAD SIZE. 1D AND 1B MODE REPLY11AA05 CYPMA 19NUMBER,CGA,CONNECTION,FITTING,OUTLET OUTLET FITTING CONNECTION CGA NUMBER A DESIGNATION NUMBER ASSIGNED TO THE OUTLET FITTING CONNECTION, IN ACCORDANCE WITH THE COMPRESSED GAS ASSOCIATION. 1A MODE REPLY 0 CYPND 18TYPE,INDICATOR,INLET INLET INDICATOR TYPE INDICATES THE TYPE OF INLET INDICATOR PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AJ89 CYPPD 18TYPE,INDICATOR,OUTLET OUTLET INDICATOR TYPE INDICATES THE TYPE OF OUTLET INDICATOR PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AJ89 CYPQD 02DESIGN,ROTOR ROTOR DESIGN THE DESIGN OF THE ROTOR. SELECT REPLY CODE 10AK54 CYPRJ 04DIAMETER,PIN,GUIDE,ACCOMMODATED ACCOMMODATED GUIDE PIN DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATION FOR THE GUIDE PIN MOUNTING HOLE, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CYPSJ 04DEPTH,PIN,GUIDE,ACCOMMODATED ACCOMMODATED GUIDE PIN DEPTH A MEASURENENT TAKEN FROM THE SURFACE OF THE GUIDE PIN RECEPTACLE TO A SPECIFIED INNER POINT ON THE ITEM, IN DISTINCTION FROM HEIGHT. 2D AND 1B MODE REPLY21AA051AC20 CYPTA 19NUMBER FOR WHICH DESIGNED,SERIES AND/OR SERIAL SERIES AND/OR SERIAL NUMBER FOR WHICH DESIGNED THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED SERIES/SERIAL NUMBER OF THE UNIT FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 CYPUD 09MATERIAL,FERRULE FERRULE MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE FERRULE IS FABRICATED. SELECT REPLY CODE 10MA01 CYPVD 09MATERIAL,BRUSH PART BRUSH PART MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE BRUSH PART IS FABRICATED. SELECT REPLY CODE 10MA01 CYPWD 14SHAPE,BRUSH BRUSH SHAPE THE PHYSICAL CONFIGURATION OF THE BRUSH. SELECT REPLY CODE 10AD07 CYPXJ 04THICKNESS,BRUSH PART BRUSH PART THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF THE BRUSH PART, IN DISTINCTION FROM LENGTH OR WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CYPYD 18TYPE,BRUSH EDGE BRUSH EDGE TYPE INDICATES THE TYPE OF BRUSH EDGE. SELECT REPLY CODE 10AN25 CYPZA 19NUMBER,MANUFACTURER AND PART/MODEL,CAMERA CAMERA MANUFACTURER AND PART/MODEL NUMBER THE 5-POSITION COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE AND PART/MODEL NUMBER OF THE CAMERA. 1A MODE REPLY 0 CYQAJ 10RATE,TRANSFER,TRANSMISSION,DATA DATA TRANSMISSION TRANSFER RATE THE RATE AT WHICH DATA CAN BE TRANSFERRED FROM ONE SOURCE TO ANOTHER, EXPRESSED IN BYTES PER SECOND (B/S. 2D AND 1B MODE REPLY23AN472AG67 CYQBD 19LANGUAGE,PROGRAMMING PROGRAMMING LANGUAGE AN ARTIFICIAL LANGUAGE FOR EXPRESSING THE PROGRAM. SELECT REPLY CODE 10AP83 CYQCD 18TYPE/NAME,SYSTEM,OPERATING OPERATING SYSTEM TYPE/NAME THE DESIGNATION FOR A SYSTEM PROGRAM WHICH ENABLES THE USER TO HAVE ACCESS TO AND USE THE COMPUTER ARCHITECTURE AND PERIPHERY. SELECT REPLY CODE 10AP84 CYZZG /D/ 19COMPONENTS,FURNISHED FURNISHED COMPONENTS THE PRINCIPAL PARTS SUPPLIED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. FULL TEXT WRITE-IN 0 CZAAD /D/ 18TYPE,JOINT,UNIVERSAL UNIVERSAL JOINT TYPE INDICATES THE TYPE OF UNIVERSAL JOINT. SELECT REPLY CODE 10AF58 CZABJ /D/ 04DIAMETER,OUTSIDE,NOMINAL,BEARING BEARING NOMINAL OUTSIDE DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CZACJ /D/ 04DISTANCE FROM END OF BEARING CAP TO BEARING CAP,NOMINAL NOMINAL DISTANCE FROM END OF BEARING CAP TO BEARING CAP THE NOMINAL DISTANCE BETWEEN BEARING CAP ENDS. 1D AND 1B MODE REPLY11AA05 CZADJ /D/ 04DISTANCE BETWEEN SNAP RING GROOVE TO GROOVE,OUTSIDE,NOMINAL NOMINAL OUTSIDE DISTANCE BETWEEN SNAP RING GROOVE TO GROOVE THE NOMINAL OUTSIDE DISTANCE BETWEEN SNAP RING GROOVES. 1D AND 1B MODE REPLY11AA05 CZAEJ /D/ 04DISTANCE BETWEEN BOLT HOLES FROM WING TO WING,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES FROM WING TO WING THE CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES FROM WING TO WING. 1D AND 1B MODE REPLY11AA05 CZAFJ /D/ 04DISTANCE BETWEEN BOLT HOLES ON THE WING,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ON THE WING THE CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ON THE WING. 1D AND 1B MODE REPLY11AA05 CZAGJ /D/ 04DISTANCE FROM UNIVERSAL JOINT SPIDER OR BLOCK CENTERLINE TO HUB END,NOMINAL NOMINAL DISTANCE FROM UNIVERSAL JOINT SPIDER OR BLOCK CENTERLINE TO HUB END THE NOMINAL DISTANCE BETWEEN THE CENTERLINE OF THE UNIVERSAL JOINT SPIDER OR BLOCK TO THE HUB END. 1D AND 1B MODE REPLY11AA05 CZAHJ /D/ 04DISTANCE FROM UNIVERSAL JOINT SPIDER OR BLOCK CENTERLINE TO THE FLANGE OUTER FACE,NOMINAL NOMINAL DISTANCE FROM UNIVERSAL JOINT SPIDER OR BLOCK CENTERLINE TO THE FLANGE OUTER FACE THE NOMINAL DISTANCE BETWEEN THE CENTERLINE OF THE UNIVERSAL JOINT SPIDER OR BLOCK TO THE FLANGE OUTER FACE. 1D AND 1B MODE REPLY11AA05 CZAJD /D/ 18TYPE/DESIGNATION,MOUNTING,SAE STANDARD SAE STANDARD MOUNTING TYPE/DESIGNATION THE TYPE OR GROUP DESIGNATION OF THE SOCIETY OF AUTOMOTIVE ENGINEERS (SAE) STANDARD MOUNTING. SELECT REPLY CODE 10AM39 CZAKJ /D/ 04DIAMETER,NOMINAL,COUNTERBORE,COUPLING COUPLING COUNTERBORE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COUNTERBORED PORTION OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CZALJ /D/ 04DIAMETER,TUBE TUBE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CZAMJ /D/A18TYPE AND QUANTITY,JOINT JOINT TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF JOINTS PROVIDED. 1D AND 1A MODE REPLY13AM39 CZANJ /D/ 04DISTANCE FROM UNIVERSAL JOINT SPIDER OR BLOCK CENTERLINE TO SHAFT END,NOMINAL NOMINAL DISTANCE FROM UNIVERSAL JOINT SPIDER OR BLOCK CENTERLINE TO SHAFT END THE NOMINAL DISTANCE BETWEEN THE CENTERLINE OF THE UNIVERSAL JOINT SPIDER OR BLOCK TO THE SHAFT END. 1D AND 1B MODE REPLY11AA05 CZAPJ /D/ 04DISTANCE BETWEEN SPRING SEAT CENTERS,NOMINAL NOMINAL DISTANCE BETWEEN SPRING SEAT CENTERS THE NOMINAL DISTANCE BETWEEN THE SPRING SEAT CENTERS. 1D AND 1B MODE REPLY11AA05 CZAQJ /D/ 10AREA,SURFACE,FRICTION,NOMINAL NOMINAL FRICTION SURFACE AREA A NOMINAL MEASUREMENT OF THE FRICTION SURFACE AREA OF THE ITEM. 1D AND 1B MODE REPLY12AG67 CZARJ /D/ 04DIAMETER,NOMINAL,BORE,HUB,FIELD FIELD HUB BORE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE FIELD HUB BORE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CZASJ /D/ 04DIAMETER,NOMINAL,BORE HUB,ARMATURE ARMATURE BORE HUB NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ARMATURE HUB BORE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CZATA /D/ 12QUANTITY,SPEED,FORWARD,TRANSMISSION,TRANSFER TRANSFER TRANSMISSION FORWARD SPEED QUANTITY THE NUMBER OF TRANSFER TRANSMISSION FORWARD SPEED RANGES PROVIDED. 1A MODE REPLY 0 CZAUA /D/ 12QUANTITY,SPEED,REVERSE,TRANSMISSION,TRANSFER TRANSFER TRANSMISSION REVERSE SPEED QUANTITY THE NUMBER OF TRANSFER TRANSMISSION REVERSE SPEED RANGES PROVIDED. 1A MODE REPLY 0 CZAVJ /D/ 04DIAMETER,NOMINAL,RACE,FORK FORK RACE NOMINAL DIAMETER THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FORK RACE,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CZAWJ /D/ 04WIDTH,NOMINAL,RACE,FORK FORK RACE NOMINAL WIDTH A NOMINAL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FORK RACE,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 CZAXA /D/ 10RATIO,FORWARD,FIXED GEAR FIXED GEAR FORWARD RATIO THE RATIO BETWEEN FIXED GEARS FOR FORWARD ACTION. 1A MODE REPLY 0 CZAYA /D/ 10RATIO,REVERSE,FIXED GEAR FIXED GEAR REVERSE RATIO THE RATIO BETWEEN FIXED GEARS FOR REVERSE ACTION. 1A MODE REPLY 0 CZAZJ /D/ 04LENGTH,OVERALL,NOMINAL NOMINAL OVERALL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CZBAJ /D/ 04DIAMETER,OUTSIDE,NOMINAL,FLANGE FLANGE NOMINAL OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZBBJ /D/ 04THICKNESS,NOMINAL,FLANGE,SECOND SECOND FLANGE NOMINAL THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 CZBCJ /D/ 04DIAMETER,OUTSIDE,NOMINAL,JAW CIRCLE JAW CIRCLE NOMINAL OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZBDJ /D/ 04LENGTH,NOMINAL,PROJECTION,JAW JAW PROJECTION NOMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CZBEJ /D/ 04DIAMETER,INSIDE,NOMINAL,JAW CIRCLE JAW CIRCLE NOMINAL INSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZBFJ /D/ 04LENGTH,OVERALL,NOMINAL NOMINAL OVERALL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CZBGJ /D/ 04DIAMETER,OVERALL,NOMINAL NOMINAL OVERALL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZBHJ /D/ 04THICKNESS,NOMINAL,FLANGE FLANGE NOMINAL THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 CZBJD 08LOCATION,SECTION,ENGINE ENGINE SECTION LOCATION INDICATES THE LOCATION OF THE ITEM ON THE ENGINE SECTION. SELECT REPLY CODE 10AJ54 CZBKJ /D/ 04DIAMETER,NOMINAL,RECESS RECESS NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZBLJ /D/ 04DIAMETER,NOMINAL,FACE,RAISED RAISED FACE NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZBMJ /D/ 04LENGTH,NOMINAL,PIN PIN NOMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CZBNJ /D/ 04WIDTH,NOMINAL,FACILITY,KEYING,BODY BODY KEYING FACILITY NOMINAL WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CZBPJ /D/ 04DEPTH,NOMINAL,FACILITY,KEYING,BODY BODY KEYING FACILITY NOMINAL DEPTH NONE. 1D AND 1B MODE REPLY11AA05 CZBQJ /D/ 04DISTANCE FROM BORE CENTERLINE TO BODY KEYING FACILITY BOTTOM,NOMINAL NOMINAL DISTANCE FROM BORE CENTERLINE TO BODY KEYING FACILITY BOTTOM NONE. 1D AND 1B MODE REPLY11AA05 CZBRJ /D/ 04DISTANCE BETWEEN CENTERLINES OF BORE AND BODY KEYING FACILITY,OFFSET,NOMINAL NOMINAL OFFSET DISTANCE BETWEEN CENTERLINES OF BORE AND BODY KEYING FACILITY NONE. 1D AND 1B MODE REPLY11AA05 CZBSJ /D/ 04DIAMETER,NOMINAL,CIRCLE,BOLT,FACILITY,POSITIONING POSITIONING FACILITY BOLT CIRCLE NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZBTJ /D/ 04THICKNESS,NOMINAL,FACE,RAISED RAISED FACE NOMINAL THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 CZBUJ /D/ 04DIAMETER,OVERALL,NOMINAL NOMINAL OVERALL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZBVJ 04WIDTH,OVERALL,NOMINAL NOMINAL OVERALL WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CZBWJ /D/ 04THICKNESS,NOMINAL,RUNG RUNG NOMINAL THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 CZBXJ /D/ 04WIDTH,NOMINAL,RUNG RUNG NOMINAL WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CZBYJ /D/ 04DIAMETER,NOMINAL,COUNTERBORE COUNTERBORE NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZBZJ /D/ 04DEPTH,NOMINAL,COUNTERBORE COUNTERBORE NOMINAL DEPTH NONE. 1D AND 1B MODE REPLY11AA05 CZCAJ /D/ 04DIAMETER,NOMINAL,CIRCLE,BOLT BOLT CIRCLE NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZCBJ /D/ 04DEPTH,NOMINAL,KEYWAY KEYWAY NOMINAL DEPTH NONE. 1D AND 1B MODE REPLY11AA05 CZCCJ /D/ 04WIDTH,NOMINAL,KEY KEY NOMINAL WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CZCDJ /D/ 04DIAMETER,NOMINAL,BORE BORE NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZCEJ /D/ 04DIAMETER,OVERALL,NOMINAL NOMINAL OVERALL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZCFJ /D/ 04HEIGHT,NOMINAL,KEY KEY NOMINAL HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 CZCGJ /D/ 04THICKNESS,NOMINAL,HUB HUB NOMINAL THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 CZCHJ /D/ 04WIDTH,NOMINAL,KEY,DIFFERENTIATING DIFFERENTIATING KEY NOMINAL WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CZCJA 19NUMBER,STAGE STAGE NUMBER THE NUMBER VALUE THAT REFLECTS THE STAGE WHERE THE ITEM IS USED. 1A MODE REPLY 0 CZCKJ /D/ 04WIDTH,NOMINAL,KEYWAY,DIFFERENTIATING DIFFERENTIATING KEYWAY NOMINAL WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CZCLJ /D/ 04HEIGHT,NOMINAL,KEY,DIFFERENTIATING DIFFERENTIATING KEY NOMINAL HEIGHT NONE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1D AND 1B MODE REPLY11AA05 CZCMJ /D/ 04DEPTH,NOMINAL,KEYWAY,DIFFERENTIATING DIFFERENTIATING KEYWAY NOMINAL DEPTH NONE. 1D AND 1B MODE REPLY11AA05 CZCNJ /D/ 04DISTANCE FROM BORE CENTERLINE TO BOTTOM OF KEYING FACILITY,NOMINAL NOMINAL DISTANCE FROM BORE CENTERLINE TO BOTTOM OF KEYING FACILITY NONE. 1D AND 1B MODE REPLY11AA05 CZCPJ /D/ 04LENGTH,OVERALL,NOMINAL NOMINAL OVERALL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CZCQJ /D/ 04LENGTH,NOMINAL,SHANK SHANK NOMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CZCRJ /D/ 04DIAMETER,NOMINAL,SHANK SHANK NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZCSJ /D/ 04HEIGHT,OVERALL,NOMINAL NOMINAL OVERALL HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 CZCTJ /D/ 04WIDTH,OVERALL,NOMINAL NOMINAL OVERALL WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CZCUJ /D/ 04WIDTH,NOMINAL,SLOT,MOUNTING MOUNTING SLOT NOMINAL WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CZCVJ /D/ 04DISTANCE,OFFSET,NOMINAL NOMINAL OFFSET DISTANCE NONE. 1D AND 1B MODE REPLY11AA05 CZCWJ /D/ 04LENGTH,NOMINAL,BORE BORE NOMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CZCXJ /D/ 04WIDTH,NOMINAL,FORK FORK NOMINAL WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CZCYJ /D/ 04DISTANCE FROM MOUNTING FACILITY CENTERLINE TO ARCH CENTERLINE,NOMINAL NOMINAL DISTANCE FROM MOUNTING FACILITY CENTERLINE TO ARCH CENTERLINE NONE. 1D AND 1B MODE REPLY11AA05 CZCZJ /D/ 04WIDTH,NOMINAL,END,FORK FORK END NOMINAL WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CZDAJ /D/ 04RADIUS,INSIDE,NOMINAL,ARCH ARCH NOMINAL INSIDE RADIUS NONE. 1D AND 1B MODE REPLY11AA05 CZDBJ /D/ 04WIDTH,OPENING,NOMINAL,FORK END FORK END NOMINAL OPENING WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CZDCJ /D/ 04HEIGHT,OPENING,NOMINAL,FORK END FORK END NOMINAL OPENING HEIGHT NONE. 1D AND 1B MODE REPLY11AA05 CZDDJ /D/ 04THICKNESS,NOMINAL,PROJECTION,FORK END FORK END PROJECTION NOMINAL THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 CZDEJ /D/ 04LENGTH,NOMINAL,PROJECTION,FORK END FORK END PROJECTION NOMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CZDFJ /D/ 04SIZE,NOMINAL,HOLE,MOUNTING MOUNTING HOLE NOMINAL SIZE NONE. 1D AND 1B MODE REPLY11AA05 CZDGJ /D/ 04LENGTH,OVERALL,NOMINAL NOMINAL OVERALL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CZDHJ 04DIAMETER,OVERALL,NOMINAL NOMINAL OVERALL DIAMETER A NOMINAL MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE. 1D AND 1B MODE REPLY11AA05 CZDJA 08LOCATION,AIRCRAFT AIRCRAFT LOCATION INDICATES THE LOCATION AT WHICH THE ITEM IS USED IN THE AIRCRAFT. 1A MODE REPLY 0 CZDKJ /D/ 04DIAMETER,NOMINAL,CIRCLE,BOLT BOLT CIRCLE NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZDLJ /D/ 04DIAMETER,NOMINAL,HUB HUB NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZDMJ /D/ 04THICKNESS,NOMINAL,FLANGE FLANGE NOMINAL THICKNESS NONE. 1D AND 1B MODE REPLY11AA05 CZDNJ /D/ 04DIAMETER,OUTSIDE,NOMINAL,BEARING BEARING NOMINAL OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZDPJ /D/ 04DISTANCE FROM END OF BEARING CAP TO BEARING CAP,OVERALL,NOMINAL NOMINAL OVERALL DISTANCE FROM END OF BEARING CAP TO BEARING CAP NONE. 1D AND 1B MODE REPLY11AA05 CZDQJ /D/ 04DISTANCE BETWEEN SNAP RING GROOVE TO GROOVE,OUTSIDE,OVERALL,NOMINAL NOMINAL OVERALL OUTSIDE DISTANCE BETWEEN SNAP RING GROOVE TO GROOVE NONE. 1D AND 1B MODE REPLY11AA05 CZDRJ /D/ 04DISTANCE BETWEEN BOLT HOLES FROM WING TO WING,OVERALL,NOMINAL,CENTER TO CENTER CENTER TO CENTER NOMINAL OVERALL DISTANCE BETWEEN BOLT HOLES FROM WING TO WING NONE. 1D AND 1B MODE REPLY11AA05 CZDSJ /D/ 04DISTANCE BETWEEN BOLT HOLES ON THE WING,OVERALL,NOMINAL,CENTER TO CENTER CENTER TO CENTER NOMINAL OVERALL DISTANCE BETWEEN BOLT HOLES ON THE WING NONE. 1D AND 1B MODE REPLY11AA05 CZDTJ /D/ 04LENGTH,OVERALL,NOMINAL NOMINAL OVERALL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CZDUJ /D/ 04WIDTH,NOMINAL,HOUSING HOUSING NOMINAL WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CZDVJ /D/ 04DISTANCE FROM CENTERLINE OF SHAFT TO COLLAR FACE,NOMINAL NOMINAL DISTANCE FROM CENTERLINE OF SHAFT TO COLLAR FACE NONE. 1D AND 1B MODE REPLY11AA05 CZDWJ /D/ 04DIAMETER,NOMINAL,SHAFT,FIRST FIRST SHAFT NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZDXJ /D/ 04DIAMETER,NOMINAL,SHAFT,SECOND SECOND SHAFT NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZDYJ /D/ 04LENGTH,NOMINAL,SHAFT,FIRST FIRST SHAFT NOMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CZDZJ /D/ 04LENGTH,NOMINAL,SHAFT,SECOND SECOND SHAFT NOMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CZEAJ /D/ 04DIAMETER,OUTSIDE,NOMINAL,HUB,FIRST FIRST HUB NOMINAL OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZEBJ /D/ 04DIAMETER,OUTSIDE,NOMINAL,HUB,SECOND SECOND HUB NOMINAL OUTSIDE DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZECJ /D/ 04LENGTH,NOMINAL,HUB,FIRST FIRST HUB NOMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CZEDJ /D/ 04LENGTH,NOMINAL,HUB,SECOND SECOND HUB NOMINAL LENGTH NONE. 1D AND 1B MODE REPLY11AA05 CZEEJ /D/ 04DIAMETER,NOMINAL,HOLE,POSITIONING POSITIONING HOLE NOMINAL DIAMETER NONE. 1D AND 1B MODE REPLY11AA05 CZEFJ 04LENGTH,CASE,CARTRIDGE CARTRIDGE CASE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF A CARTRIDGE CASE,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AF47 CZEGJ /D/ 04LENGTH,CHARGE,PROPELLANT,CARTRIDGE,CASELESS CASELESS CARTRIDGE PROPELLANT CHARGE LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE PROPELLANT CHARGE OF THE CASELESS CARTRIDGE. 1D AND 1B MODE REPLY11AF47 CZEHJ A18TYPE AND QUANTITY ACCOMMODATED,COMPONENT COMPONENT TYPE AND QUANTITY ACCOMMODATED INDICATES THE TYPE AND NUMBER OF COMPONENTS ACCOMMODATED BY THE ITEM. 1D AND 1A MODE REPLY13AK95 CZEJA 19NUMBER,STATION,AIRCRAFT AIRCRAFT STATION NUMBER THE STATION NUMBER REFERENCE POINT ON AN AIRCRAFT. 1A MODE REPLY 0 CZEKA 19SERIES,DESIGN,MISSION,AIRCRAFT AIRCRAFT MISSION DESIGN SERIES THE SERIES OF LETTERS AND NUMBERS WHICH IDENTIFY THE BASIC AIRCRAFT MISSION AND ANY ADDITIONAL MODIFICATION OR DESIGN CHANGES. 1A MODE REPLY 0 CZELA /D/ 08LOCATION,FINISH,MICROMETER MICROMETER FINISH LOCATION INDICATES THE LOCATION OF THE MICROMETER FINISH ON THE ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1A MODE REPLY 0 CZEMJ A18TYPE AND QUANTITY,DEVICE,MICROCIRCUIT MICROCIRCUIT DEVICE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF MICROCIRCUIT DEVICES PROVIDED. 1D AND 1A MODE REPLY13AJ12 CZENJ 10VOLTAGE RATING AND TYPE PER CHARACTERISTIC VOLTAGE RATING AND TYPE PER CHARACTERISTIC THE VALUE OF THE VOLTAGE APPLIED AND TYPE OF SPECIFIC ELECTRICAL CHARACTERISTIC FOR WHICH THE ITEM IS DESIGNED. 3D AND 1B MODE REPLY31AB631AC203AP75 CZEPJ 10CAPITANCE RATING PER CHARACTERISTIC CAPITANCE RATING PER CHARACTERISTIC THE RELATIVE LEVEL OF THE QUANTITY OF ELECTRICAL CHARGE AT A GIVEN POTENTIAL WHICH THE ITEM IS RECEIVING AND STORING PER CHARACTERISTIC. 3D AND 1B MODE REPLY31AC002AN861AC20 CZEQJ 10TIME RATING PER CHARACTERISTIC TIME RATING PER CHACTERISTIC THE ACCEPTABLE TIME LIMITATION FOR THE ITEM PER CHARACTERISTIC. 3D AND 1B MODE REPLY32AH681AC203AP75 CZERD 18TYPE,DEVICE,MEMORY MEMORY DEVICE TYPE INDICATES THE TYPE OF MEMORY DEVICE USED ON THE ITEM. SELECT REPLY CODE 10AN47 CZESD 18TYPE,TECHNOLOGY,HYBRID HYBRID TECHNOLOGY TYPE INDICATES THE TYPE OF HYBRID TECHNOLOGY USED IN THE ITEM. SELECT REPLY CODE 10AJ21 CZETJ 04DIAMETER,BEVEL,INTERNAL,END END INTERNAL BEVEL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CZEUJ 04DIAMETER,TAPER,MINOR,BODY BODY MINOR TAPER DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CZEVJ 04ANGLE,BEVEL,INTERNAL,END END INTERNAL BEVEL ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CZEWJ 04ANGLE,BEVEL,INTERNAL,END,SMALLEST SMALLEST END INTERNAL BEVEL ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CZEXJ 04TAPER,BODY BODY TAPER NONE. 2D AND 1B MODE REPLY21AP381AC20 CZEYJ 04DIAMETER,INSIDE,FIRST LEFT COUNTERBORE FIRST LEFT COUNTERBORE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CZEZJ 04DIAMETER,OUTSIDE,STEP,FIRST LEFT FIRST LEFT STEP OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CZFAJ 04DIAMETER,INSIDE,SECOND LEFT COUNTERBORE SECOND LEFT COUNTERBORE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CZFBJ 04DIAMETER,OUTSIDE,STEP,SECOND LEFT SECOND LEFT STEP OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CZFCJ 04DIAMETER,INSIDE,FIRST RIGHT COUNTERBORE FIRST RIGHT COUNTERBORE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CZFDJ 04DIAMETER,OUTSIDE,STEP,FIRST RIGHT FIRST RIGHT STEP OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CZFEJ 04DIAMETER,INSIDE,SECOND RIGHT COUNTERBORE SECOND RIGHT COUNTERBORE INSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CZFFJ 04DIAMETER,OUTSIDE,STEP,SECOND RIGHT SECOND RIGHT STEP OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CZFGJ 04DISTANCE FROM END TO LEG ALONG LENGTH DISTANCE FROM END TO LEG ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CZFHJ /D/ 04DIAMETER,CHAMBER CHAMBER DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CZFJB 10COMPOUND IN GRAMS PER LITER,ORGANIC,VOLATILE VOLATILE ORGANIC COMPOUND IN GRAMS PER LITER THE VOLATILE ORGANIC COMPOUND OF THE ITEM AS RATED BY INDUSTRY,EXPRESSED IN GRAMS PER LITER. 1B MODE REPLY 0 CZFKJ 10CONTENT,COMPOUND,VOLATILE VOLATILE COMPOUND CONTENT THE AMOUNT OF VOLATILE COMPOUND INCLUDED IN THE ITEM. 1D AND 1B MODE REPLY12AB49 CZFLJ 04WIDTH WIDTH A MEASUREMENT OF THE SHORTEST DIMENSION OF THE ITEM,IN DISTINCTION FROM LENGTH. 2D AND 1B MODE REPLY21AA051AC20 CZFMJ 04DISTANCE,ADJUSTMENT,LATERAL LATERAL ADJUSTMENT DISTANCE THE DISTANCE THE ITEM CAN BE ADJUSTED TO EITHER SIDE. 2D AND 1B MODE REPLY21AA051AC20 CZFNJ /D/ 04DISTANCE BETWEEN DOOR TO FLOOR DISTANCE BETWEEN DOOR TO FLOOR THE DISTANCE BETWEEN THE BOTTOM OF THE DOOR AND THE SURFACE OF THE FLOOR. 2D AND 1B MODE REPLY21AA051AC20 CZFPJ 04THICKNESS THICKNESS NONE. 2D AND 1B MODE REPLY21AA051AC20 CZFQJ 10SIZE,HOLE,FIRST SURFACE FIRST SURFACE HOLE SIZE NONE. 2D AND 1B MODE REPLY21AA051AC20 CZFRJ 10SIZE,HOLE,SECOND SURFACE SECOND SURFACE HOLE SIZE NONE. 2D AND 1B MODE REPLY21AA051AC20 CZFSJ 04DISTANCE,OFFSET,LEVER LEVER OFFSET DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CZFTJ 04DISTANCE,OFFSET,BOLT BOLT OFFSET DISTANCE NONE. 2D AND 1B MODE REPLY21AA051AC20 CZFUJ 04ANGLE,SWING,PAWL PAWL SWING ANGLE NONE. 2D AND 1B MODE REPLY21AP381AC20 CZFVB /D/ 10PRESSURE IN HECTOPASCALS,GAS,MAXIMUM MAXIMUM GAS PRESSURE IN HECTOPASCALS THE MAXIMUM GAS PRESSURE THE ITEM IS DESIGNED TO ACCOMMODATE,EXPRESSED IN HECTOPASCALS. 1B MODE REPLY 0 CZFWJ 04DISTANCE BETWEEN SMALLEST BOLT HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN SMALLEST BOLT HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 CZFXJ 04DISTANCE BETWEEN LARGEST BOLT HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN LARGEST BOLT HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 CZFYJ 04DISTANCE ALONG WIDTH,OUTSIDE EDGE TO SMALLEST BOLT HOLE CENTER OUTSIDE EDGE TO SMALLEST BOLT HOLE CENTER DISTANCE ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CZFZJ 04DISTANCE ALONG LENGTH,OUTSIDE EDGE TO SMALLEST BOLT HOLE CENTER OUTSIDE EDGE TO SMALLEST BOLT HOLE CENTER DISTANCE ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CZGAJ 04DISTANCE ALONG WIDTH,OUTSIDE EDGE TO LARGEST BOLT HOLE CENTER OUTSIDE EDGE TO LARGEST BOLT HOLE CENTER DISTANCE ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CZGBJ 04DISTANCE ALONG LENGTH,OUTSIDE EDGE TO LARGEST BOLT HOLE CENTER OUTSIDE EDGE TO LARGEST BOLT HOLE CENTER DISTANCE ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CZGCJ 09DURATION DURATION AN INDICATION OF THE DURATION. 1D AND 1B MODE REPLY12AB49 CZGDA /D/ 12QUANTITY,POSITION,SLOT SLOT POSITION QUANTITY THE NUMBER OF SLOT POSITIONS IN THE ITEM. 1A MODE REPLY 0 CZGED /D/ 19MODE,TRANSMISSION TRANSMISSION MODE THE TRANSMISSION MODE USED ON THE ITEM. SELECT REPLY CODE 10AJ71 CZGFD 18TYPE,LINK LINK TYPE INDICATES THE TYPE OF LINK. SELECT REPLY CODE 10AK41 CZGGD /D/ 18TYPE,BAIT BAIT TYPE INDICATES THE TYPE OF BAIT PROVIDED WITH THE ITEM. SELECT REPLY CODE 10AK54 CZGHJ 04WIDTH,FLOATING,MAXIMUM,NUT NUT MAXIMUM FLOATING WIDTH NONE. 1D AND 1B MODE REPLY11AA05 CZGJD 08LOCATION,PLACEMENT,BOLT BOLT PLACEMENT LOCATION INDICATES THE LOCATION ON THE BOLT WHERE THE ITEM IS TO BE PLACED. SELECT REPLY CODE 10AJ91 CZGKD /D/ 13THREAD SERIES DESIGNATOR,BOLT BOLT THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER OF A BOLT. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AH06 CZGLJ A10STRENGTH,TENSIL,MINIMUM,BOLT BOLT MINIMUM TENSIL STRENGTH THE MAXIMUM RATED LOAD IN TENSION,APPLIED IN A LONGITUDAL DIRECTION,PER UNIT OF CROSS-SECTIONAL AREA,THAT THE BOLT CAN WITHSTAND WITHOUT RUPTURE. 1D AND 1A MODE REPLY11AN71 CZGMA /D/ 10STRENGTH PERCENTAGE,YIELD,BOLT BOLT YIELD STRENGTH PERCENTAGE THE INDUCED PRELOAD PERCENTAGE OF A BOLT YIELD STRENGTH FOR WHICH THE ITEM IS DESIGNED. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1A MODE REPLY 0 CZGNJ /D/ 13THREAD DIAMETER,BOLT BOLT THREAD DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE BOLT,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CZGPJ 04LENGTH,UNLOADED UNLOADED LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CZGQJ 10SIZE,NECK NECK SIZE DESIGNATES THE SIZE OF THE NECK. 2D AND 1B MODE REPLY21AA051AC20 CZGRA 12QUANTITY,PORT,VALVE VALVE PORT QUANTITY THE NUMBER OF VALVE PORTS PROVIDED ON THE ITEM. 1A MODE REPLY 0 CZGSD 03DESIGNATOR OF THE MALE OR FEMALE CONNECTOR,TRADE TRADE DESIGNATOR OF THE MALE OR FEMALE CONNECTOR THE DESIGNATION BY WHICH THE MALE OR FEMALE CONNECTOR IS IDENTIFIED THROUGHOUT INDUSTRY. SELECT REPLY CODE 10AK54 CZGTB /D/ 10TEMP IN DEG CELSIUS,FREEZING FREEZING TEMP IN DEG CELSIUS THE TEMPERATURE AT WHICH THE ITEM WILL FREEZE,EXPRESSED IN DEGREES CELSIUS. 1B MODE REPLY 0 CZGUJ /D/ 10PITCH,PERFORATION PERFORATION PITCH THE DISTANCE BETWEEN ADJACENT HOLES OF A PERFORATED ITEM. 1D AND 1B MODE REPLY11AA05 CZGVL /D/ 16STYLE,PROFILE,TOOTH TOOTH PROFILE STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE PROFILE OF THE TOOTH. 1L MODE REPLY 0 CZGWJ 04WIDTH,SHAFT,LARGEST LARGEST SHAFT WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CZGXL 16STYLE,PATTERN,HOLE,MOUNTING,DEVICE,ACCOMMODATED ACCOMMODATED DEVICE MOUNTING HOLE PATTERN STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE PATTERN OF THE FACILITY BY WHICH THE DEVICE CAN BE MOUNTED. 1L MODE REPLY 0 CZGYA 12QUANTITY,HOLE,MOUNTING,DEVICE,ACCOMMODATED ACCOMMODATED DEVICE MOUNTING HOLE QUANTITY THE NUMBER OF MOUNTING HOLES ACCOMMODATED ON THE DEVICE. 1A MODE REPLY 0 CZGZJ /D/A10REDUCTION REDUCTION THE POWER AND/OR AMOUNT OF APPARENT REDUCTION BY THE ITEM. 1D AND 1A MODE REPLY11AC20 CZHAD /D/ 09MATERIAL,POINT,CONTACT CONTACT POINT MATERIAL THE ELEMENT,COMPOUND OR MIXTURE OF WHICH THE CONTACT POINT IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. SELECT REPLY CODE 10AD09 CZHBA 12QUANTITY IN 360 DEGREES,TOOTH TOOTH QUANTITY IN 360 DEGREES THE NUMBER OF TEETH CONTAINED ON A SIMILAR 360 DEGREE GEAR. 1A MODE REPLY 0 CZHCJ 10ARC,COMPLEMENT,TOOTHED TOOTHED COMPLEMENT ARC THE ANGULAR PORTION OF A FULL GEAR CONTAINED IN THE TOOTHED COMPLEMENT. 1D AND 1B MODE REPLY11AP38 CZHDJ /D/ 04SIZE,THREAD,HOLE,SECURING SECURING HOLE THREAD SIZE DESIGNATES THE THREAD DIAMETER OF THE SECURING HOLE. 1D AND 1B MODE REPLY11AA05 CZHED /D/ 13THREAD SERIES DESIGNATOR,HOLE,SECURING SECURING HOLE THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF SECURING HOLE THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE. SELECT REPLY CODE 10AH06 CZHFJ /D/ 04SIZE,THREAD,NOMINAL,BUSHING,PANEL PANEL BUSHING NOMINAL THREAD SIZE DESIGNATES THE NOMINAL THREAD DIAMETER OF THE PANEL BUSHING. 1D AND 1B MODE REPLY11AA05 CZHGD /D/ 13THREAD SERIES DESIGNATOR,BUSHING,PANEL PANEL BUSHING THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF PANEL BUSHING THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE. SELECT REPLY CODE 10AH06 CZHHJ 04DIAMETER,HOLE,MATERIAL,FASTENER FASTENER MATERIAL HOLE DIAMETER THE DIAMETER OF THE MATERIAL HOLE THAT THE FASTENER WAS DESIGNED TO BE PRESSED IN. 2D AND 1B MODE REPLY21AA051AC20 CZHJD /D/ 18TYPE,INDICATOR,TENSION,DIRECT DIRECT TENSION INDICATOR TYPE THE DIRECT TENSION INDICATOR TYPE THAT INDICATES WHAT ASTM BOLT STANDARD TO USE WITH THE ITEM. SELECT REPLY CODE 10AJ46 CZHKJ 04LENGTH,OVERALL,BUTTON,PUSH PUSH BUTTON OVERALL LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CZHLJ 04LENGTH,GRIP,BUTTON,PUSH PUSH BUTTON GRIP LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CZHMJ /D/ 04LENGTH,RECEPTACLE,STUD STUD RECEPTACLE LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CZHNJ /D/ 04DISTANCE BETWEEN HEXAGONAL BORE FLATS DISTANCE BETWEEN HEXAGONAL BORE FLATS NONE. 2D AND 1B MODE REPLY21AA051AC20 CZHPJ 04DIAMETER FOR WHICH DESIGNED,THREAD,BOLT BOLT THREAD DIAMETER FOR WHICH DESIGNED THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION OF THE BOLT,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 CZHQL 16STYLE,WHEEL WHEEL STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE WHEEL. 1L MODE REPLY 0 CZHRL 16STYLE,FRAME FRAME STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FRAME. 1L MODE REPLY 0 CZHSL 16STYLE,SEGMENT SEGMENT STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SEGMENT. 1L MODE REPLY 0 CZHTA 19NUMBER,STOCK,NATIONAL,GASES/CYLINDERS,RELATED RELATED GASES/CYLINDERS NATIONAL STOCK NUMBER THE NATIONAL STOCK NUMBER DESIGNATION OF FILLED OR RELATED GASES OR CYLINDERS IN THE SUPPLY SYSTEM. 1A MODE REPLY 0 CZHUA 12QUANTITY,ARM ARM QUANTITY THE NUMBER OF ARMS PROVIDED. 1A MODE REPLY 0 CZHVJ /D/ 04DISTANCE BETWEEN ARMS,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN ARMS NONE. 2D AND 1B MODE REPLY21AA051AC20 CZHWJ /D/ 10LOAD ACCOMMODATED,ARM ARM LOAD ACCOMMODATED A MEASUREMENT OF THE WEIGHT THE ARM IS DESIGNED TO ACCOMMODATE. 1D AND 1B MODE REPLY12AN75 CZHXD /D/ 18TYPE,GROUPING,CARTRIDGE,BLANK BLANK CARTRIDGE GROUPING TYPE INDICATES THE PARTICULAR KIND OF GROUPING IN WHICH THE BLANK CARTRIDGE IS SUPPLIED. SELECT REPLY CODE 10AF44 CZHYA /D/ 12QUANTITY,CARTRIDGE,BLANK BLANK CARTRIDGE QUANTITY THE TOTAL NUMBER OF BLANK CARTRIDGES OF WHICH THE GROUPING IS COMPOSED. 1A MODE REPLY 0 CZHZA /D/ 19NUMBER,MODEL,CARTRIDGE,SHOTGUN SHOTGUN CARTRIDGE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE SHOTGUN CARTRIDGE. 1A MODE REPLY 0 CZJAD /D/ 18TYPE,DESIGN,CARTRIDGE,SHOTGUN SHOTGUN CARTRIDGE DESIGN TYPE INDICATES THE DESIGN TYPE CHARACTERISTIC OF THE SHOTGUN CARTRIDGE. SELECT REPLY CODE 10AF43 CZJBD /D/ 18TYPE,DESIGN,BOMB,MORTAR MORTAR BOMB DESIGN TYPE INDICATES THE DESIGN TYPE CHARACTERISTIC OF THE MORTAR BOMB. SELECT REPLY CODE 10AF43 CZJCA /D/ 19NUMBER,MODEL,BOMB,MORTAR MORTAR BOMB MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE MORTAR BOMB. 1A MODE REPLY 0 CZJDA /D/ 19CODE,HAZARD HAZARD CODE A THREE(3) CHARACTER SIGNIFICANT NUMBER (COMPOSED OF TWO DIGITS AND ONE LETTER, THE TWO DIGITS BEING SEPARATED BY FULL STOP) ASSIGNED BY THE EXPLOSIVES STORAGE AND TRANSPORT COMMITTEE TO CLASSIFY THE UN HAZARD DIVISION AND THE UN AND NATO COMPATIBILITY GROUP OF MILITARY EXPLOSIVES. 1A MODE REPLY 0 CZJED /D/ 18TYPE,FILLER,BOMB,MORTAR MORTAR BOMB FILLER TYPE INDICATES THE TYPE OF FILLER WHICH IS CONTAINED WITHIN THE MORTAR BOMB. SELECT REPLY CODE 10AF45 CZJFA /D/ 19NUMBER,MODEL,PRIMER,ELECTRIC ELECTRIC PRIMER MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE ELECTRIC PRIMER. 1A MODE REPLY 0 CZJGA /D/ 19NUMBER,MODEL,CARTRIDGE,BLANK BLANK CARTRIDGE MODEL NUMBER THE COMBINED GROUP OF LETTERS,NUMERALS AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE BLANK CARTRIDGE. 1A MODE REPLY 0 CZJHL /D/ 03DESIGNATOR,LINK,CHAIN CHAIN LINK DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CHAIN LINK. 1L MODE REPLY 0 CZJJL /D/ 16STYLE,END,PERIPHERAL PERIPHERAL END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE EXTERNAL OR PERIPHERAL END. 1L MODE REPLY 0 CZJKJ /D/ 04DISTANCE BETWEEN THREADED HOLES,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN THREADED HOLES NONE. 2D AND 1B MODE REPLY21AA051AC20 CZJLJ /D/A10STRESS,LOAD,PROOF,NUT NUT PROOF LOAD STRESS THE TENSILE STRESS TO WHICH A NUT IS TESTED AND CAN WITHSTAND WITHOUT FAILING BY STRIPPING OR RUPTURE AND WITHOUT DISTORTION TO THE THREADS. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1D AND 1A MODE REPLY11AB18 CZJML /D/ 16STYLE,END,HUB HUB END STYLE THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE INTERNAL OR HUB END. 1L MODE REPLY 0 CZJNJ /D/ 04DISTANCE BETWEEN BOLT HOLE AND MOUNTING SLOT ALONG LENGTH,MINOR,CENTER TO CENTER CENTER TO CENTER MINOR DISTANCE BETWEEN BOLT HOLE AND MOUNTING SLOT ALONG LENGTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CZJPJ /D/ 04DISTANCE BETWEEN BOLT HOLE AND MOUNTING SLOT ALONG WIDTH,MINOR,CENTER TO CENTER CENTER TO CENTER MINOR DISTANCE BETWEEN BOLT HOLE AND MOUNTING SLOT ALONG WIDTH NONE. 2D AND 1B MODE REPLY21AA051AC20 CZJQJ 10INGREDIENTS PER UNIT,ACTIVE ACTIVE INGREDIENTS PER UNIT THE AMOUNT OF ACTIVE INGREDIENTS CONTAINED IN EACH UNIT. 2D AND 1B MODE REPLY22AN643AJ40 CZJRJ 04DIAMETER,HOLE,MOUNTING,PLATE PLATE MOUNTING HOLE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CZJSJ 04LENGTH AND WIDTH,FORMED FORMED LENGTH AND WIDTH A MEASUREMENT OF THE LONGEST FORMED DIMENSION,FOLLOWED BY THE WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CZJTJ /D/ 04LENGTH AND WIDTH,STRAP STRAP LENGTH AND WIDTH A MEASUREMENT OF THE LONGEST STRAP DIMENSION,FOLLOWED BY THE WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CZJUJ /D/ 04LENGTH AND WIDTH,TIE TIE LENGTH AND WIDTH A MEASUREMENT OF THE LONGEST TIE DIMENSION,FOLLOWED THE THE WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CZJVJ 04LENGTH AND WIDTH,BANDAGE BANDAGE LENGTH AND WIDTH A MEASUREMENT OF THE LONGEST BANDAGE DIMENSION,FOLLOWED BY THE WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CZJWJ 04LENGTH AND WIDTH,COMPRESS COMPRESS LENGTH AND WIDTH A MEASUREMENT OF THE LONGEST COMPRESS DIMENSION,FOLLOWED BY THE WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CZJXJ /D/ 04LENGTH AND WIDTH,PAD PAD LENGTH AND WIDTH A MEASUREMENT OF THE LONGEST PAD DIMENSION,FOLLOWED BY THE WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CZJYJ /D/ 04LENGTH AND WIDTH,SKULLCAP,SURGICAL SURGICAL SKULLCAP LENGTH AND WIDTH A MEASUREMENT OF THE LONGEST SURGICAL SKULLCAP DIMENSION,FOLLOWED BY THE WIDTH. 2D AND 1B MODE REPLY21AA051AC20 CZJZJ A18TYPE AND QUANTITY,DEVICE,SECURING SECURING DEVICE TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF DEVICES USED TO FASTEN THE ITEM. 1D AND 1A MODE REPLY12AC52 CZKAJ A19NUMBER,REFERENCE,PACKAGE PACKAGE REFERENCE NUMBER AN ALPHA-NUMERIC CODE IDENTIFYING THE DRAWING AND/OR SPECIFICATION WHICH CONTROLS THE LOADING OF THE PACKAGE. 1D AND 1A MODE REPLY12AF94 CZKBA 19NSN OF CABLE/CORD/LEAD NSN OF CABLE/CORD/LEAD THE THIRTEEN(13)DIGIT NATO STOCK NUMBER ASSIGNED TO THE CABLE CORD OR CONDUCTOR. 1A MODE REPLY 0 CZKCA /D/ 19NSN OF TERMINATION/END FITTINGS NSN OF TERMINATION/END FITTINGS THE THIRTEEN(13)DIGIT NATO STOCK NUMBER ASSIGNED TO THE TERMINATION/END FITTINGS. 1A MODE REPLY 0 CZKDH /D/ 19RELATIONSHIP,POSITION-ACTION-LOCKING,ACTUATOR ACTUATOR POSITION-ACTION-LOCKING RELATIONSHIP THE RELATIONSHIP BETWEEN THE ACTUATOR POSITION, THE ACTUATOR ACTION, AND THE INTEGRAL FACILITY PROVIDED TO PREVENT ACTUATOR MOVEMENT. 3D MODE REPLY 31AE601AE611AE62 CZKEA 12QUANTITY,SPRING SPRING QUANTITY THE NUMBER OF SPRINGS PROVIDED. 1A MODE REPLY 0 CZKFB /D/ 13THREAD PITCH IN MILLIMETERS,HOLE,SECURING SECURING HOLE THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE AXIS, EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 CZKGA 03DESIGNATOR,TYPE,NEEDLE NEEDLE TYPE DESIGNATOR A DESIGNATION INDICATING THE NEEDLE TYPE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED. 1A MODE REPLY 0 CZKHJ 10STRENGTH,COMPRESSION COMPRESSION STRENGTH THE MAXIMUM SQUEEZING LOAD AN ITEM CAN WITHSTAND WITHOUT BREAKING. 2D AND 1B MODE REPLY22AJ201AC20 CZKJA /D/ 12QUANTITY PER CENTIMETER QUANTITY PER CENTIMETER AN INDICATION OF THE NUMBER OF ITEMS PER CENTIMETER 1A MODE REPLY 0 CZKKJ /D/ 10OUTPUT,WATER,MAXIMUM MAXIMUM WATER OUTPUT INDICATES THE MAXIMUM WATER OUTPUT OF THE ITEM 1D AND 1B MODE REPLY12AG67 CZKLJ /D/ 10OUTPUT,AERATOR AIR,MAXIMUM MAXIMUM AERATOR AIR OUTPUT INDICATES THE MAXIMUM AERATOR AIR OUTPUT OF THE ITEM 2D AND 1B MODE REPLY21AD422AG67 CZKMA /D/ 19CHARACTERISTIC FOR A NEW NSN,JUSTIFICATION JUSTIFICATION CHARACTERISTIC FOR A NEW NSN THE DIFFERENTIATING CHARACTERISTICS OF THE ITEM OF SUPPLY WHICH JUSTIFY THE ASSIGNMENT OF A NEW NSN DESPITE AN APPARENT MATCH OF A DIFFERENT ITEM OF SUPPLY. 1A MODE REPLY 0 CZKNJ 10FREQUENCY,SPECIFIED SPECIFIED FREQUENCY THE FREQUENCY AT WHICH THE ITEM IS DESIGNED TO OPERATE UNDER SPECIFIED CONDITIONS. 2D AND 1B MODE REPLY21AC321AC20 CZKPJ /D/ 10RATE,FLOW,REFRIGERATION REFRIGERATION FLOW RATE THE REFRIGERATION CAPACITY OF THE ITEM AS RATED BY INDUSTRY. 1D AND 1B MODE REPLY12AG20 CZKQD /D/ 18TYPE,DESIGN,PERIPHERY,OUTER OUTER PERIPHERY DESIGN TYPE INDICATES THE DESIGN TYPE OF THE OUTER PERIPHERY OF THE ITEM. SELECT REPLY CODE 10AK54 CZKRD 09MATERIAL,FACING FACING MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE FACING IS FABRICATED. SELECT REPLY CODE 10MA01 CZKSJ 04DIAMETER,MAJOR,BORE,TAPERED,HUB HUB TAPERED BORE MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CROSS SECTION OF A TAPERED BORE, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CZKTJ 04DIAMETER,MAJOR,SPLINE,HUB,INTERNAL INTERNAL HUB SPLINE MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CROSS SECTION OF AN INTERNAL SPLINE, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CZKUA 12QUANTITY,SPLINE,SHAFT SHAFT SPLINE QUANTITY THE NUMBER OF SPLINES ON THE SHAFT. 1A MODE REPLY 0 CZKVJ 04WIDTH ACROSS FLATS,BORE,HUB HUB BORE WIDTH ACROSS FLATS THE DISTANCE FROM ONE FLAT TO THE OPPOSITE FLAT OF A HEX OR SQUARE BORE. 2D AND 1B MODE REPLY21AA051AC20 CZKWJ 04DIAMETER,MAJOR,SPLINE,SHAFT,EXTERNAL EXTERNAL SHAFT SPLINE MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CROSS SECTION OF AN EXTERNAL SPLINE, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CZKXD 18TYPE,RETAINER,BEARING BEARING RETAINER TYPE INDICATES THE TYPE OF DEVICE USED TO RETAIN THE BEARINGS IN THE YOKE. SELECT REPLY CODE 10AB28 CZKYJ 10CAPACITY,TANK,WASTE WASTE TANK CAPACITY THE CAPACITY THAT THE WASTE TANK WILL HOLD. 1D AND 1B MODE REPLY12AB49 CZKZJ 10CAPACITY,TANK,WATER WATER TANK CAPACITY THE CAPACITY THAT THE WATER TANK WILL HOLD. 1D AND 1B MODE REPLY12AB49 CZLAD 09MATERIAL,HOUSING HOUSING MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE HOUSING IS FABRICATED. SELECT REPLY CODE 10MA01 CZLBA 19NUMBER OF VARIABLE GUIDE VANES NUMBER OF VARIABLE GUIDE VANES THE NUMBER OF VARIABLE GUIDE VANES INCLUDED AS PART OF THE STRUT. 1A MODE REPLY 0 CZLCH /D/ 02DESIGN,TIRE TIRE DESIGN THE TIRE DESIGN AND THE TYPE OF BASE MOUNTING FACILITY. 3D MODE REPLY 31AN832AN843AB67 CZLDA 19MODEL NUMBER FOR WHICH DESIGNED,STRAINER STRAINER MODEL NUMBER FOR WHICH DESIGNED THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE STRAINER FOR WHICH THE ITEM IS DESIGNED. 1A MODE REPLY 0 CZLEJ A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,BALL END BALL END THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE BALL END. 1D AND 1A MODE REPLY12AH06 CZLFJ A13THREAD SIZE AND SERIES/TYPE DESIGNATOR,SOCKET END SOCKET END THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE SOCKET END. 1D AND 1A MODE REPLY12AH06 CZLGJ 04DIAMETER,OUTSIDE,HUB,FIRST END FIRST END HUB OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CZLHJ 04DIAMETER,OUTSIDE,HUB,SECOND END SECOND END HUB OUTSIDE DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CZLJJ 04DISTANCE FROM FIRST END HUB TO SHOULDER DISTANCE FROM FIRST END HUB TO SHOULDER NONE. 2D AND 1B MODE REPLY21AA051AC20 CZLKJ 04DISTANCE FROM SECOND END HUB TO SHOULDER DISTANCE FROM SECOND END HUB TO SHOULDER NONE. 2D AND 1B MODE REPLY21AA051AC20 CZLLD 14SHAPE,BORE,FULCRUM FULCRUM BORE SHAPE THE PHYSICAL CONFIGURATION OF THE FULCRUM BORE. SELECT REPLY CODE 10AD07 CZLMJ 04DISTANCE BETWEEN FULCRUM AND ARM END HOLE/SLOT/BALL,CENTER TO CENTER CENTER TO CENTER DISTANCE BETWEEN FULCRUM AND ARM END HOLE/SLOT/BALL NONE. 2D AND 1B MODE REPLY21AA051AC20 CZLNJ 04DIAMETER,HOLE/BALL,END END HOLE/BALL DIAMETER NONE. 2D AND 1B MODE REPLY21AA051AC20 CZLPD 11METHOD,SECURING,SHAFT SHAFT SECURING METHOD THE MEANS BY WHICH THE SHAFT IS SECURED. SELECT REPLY CODE 10AM39 CZLQJ 10SIZE,BORE,FULCRUM FULCRUM BORE SIZE DESIGNATES THE SIZE OF THE FULCRUM BORE. 2D AND 1B MODE REPLY21AA051AC20 CZLRD 09MATERIAL,CORE CORE MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE CORE IS FABRICATED. SELECT REPLY CODE 10MA01 CZLSA 19RATIO,PILOT PILOT RATIO INDICATES THE PILOT RATIO REQUIRED TO REMOTELY OPERATE THE VALVE. 1A MODE REPLY 0 CZLTB /D/ 10CUBIC MILLIMETERS,RATING OF NOZZLE IN,INJECTION INJECTION RATING OF NOZZLE IN CUBIC MILLIMETERS THE RATED CAPACITY OF FUEL RELEASED WITH EACH STROKE OF THE INJECTION PUMP, IN THE DIRECTION OF THE ENGINE COMBUSTION CHAMBER, EXPRESSED IN CUBIC MILLIMETERS. 1B MODE REPLY 0 CZLUJ /D/ 10HEAD,TOTAL,FUELING FUELING TOTAL HEAD THE SUM OF THE FUELING TOTAL DISCHARGE HEAD AND THE TOTAL SUCTION LIFT. 1D AND 1B MODE REPLY12AG20 CZLVJ T10RANGE,PRESSURE,ACTUATING FLUID ACTUATING FLUID PRESSURE RANGE THE MINIMUM TO MAXIMUM ACTUATING FLUID PRESSURE AT WHICH AN ITEM IS DESIGNED TO OPERATE. 1D AND 1F MODE REPLY12AG20 CZLWJ 10CAPACITY RATING,PRESSURE,MAXIMUM DRIVING MAXIMUM DRIVING PRESSURE CAPACITY RATING THE MAXIMUM DRIVING PRESSURE CAPACITY FOR WHICH AN ITEM IS RATED. 1D AND 1B MODE REPLY12AG20 CZLXJ /D/ 10PRESSURE RATING,CUTOUT,TANK TANK CUTOUT PRESSURE RATING THE RATED PRESSURE AT WHICH THE TANK CUTOUT IS SET. 2D AND 1B MODE REPLY22AG201AC20 CZLYJ /D/ 10PRESSURE RATING,CUT-IN,TANK TANK CUT-IN PRESSURE RATING THE RATED PRESSURE AT WHICH THE TANK CUT-IN IS SET. 2D AND 1B MODE REPLY22AG201AC20 CZLZL 16STYLE,TIP,FLANGE,RIGHT-SIDE RIGHT-SIDE FLANGE TIP STYLE THE STYLE DESIGNATION CORRESPONDING TO THE SHAPE OF THE RIGHT-SIDE FLANGE TIP. 1L MODE REPLY 0 CZMAD 18DISK MEDIA TYPE DISK MEDIA TYPE THE TYPE OF OPTICAL MEDIA FORMAT. SELECT REPLY CODE 10AP91 CZMBA 18MAX SPEED SUPPORTED MAX SPEED SUPPORTED THE NUMBER INDICATING THE WRITE OR RECORD SPEED "X". 1A MODE REPLY 0 CZMCD /D/ 18SHOWER TYPE SHOWER TYPE INDICATES THE TYPE OF SHOWER SELECT REPLY CODE 10AK54 CZMDJ /D/ 04WIDTH,TAPER TAPER WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LONGEST DIMENSION OF THE TAPERED PORTION OF AN ITEM, IN DISTINCTION FROM LENGTH 2D AND 1B MODE REPLY21AA051AC20 CZMED 18STYLE,ADJUSTER ADJUSTER STYLE INDICATES THE TYPE OF ADJUSTER STYLE SELECT REPLY CODE 10AB28 CZMFD /D/ 18TYPE,SUBSYSTEM SUBSYSTEM TYPE INDICATES THE TYPE OF SUBSYSTEM. USE MRC SSTP SELECT REPLY CODE 10AK54 CZMGL 16STYLE,TYPE,ACCOMMODATION,CONDUCTOR CONDUCTOR ACCOMMODATION TYPE STYLE THE STYLE DESIGNATION INDICATING THE TYPE OF CONNECTOR OR CONDUCTOR ACCOMMODATION INCLUDED ON THE ITEM. 1L MODE REPLY 0 CZMHH 18TYPE,SERVICE SERVICE TYPE INDICATES THE PRIMARY TYPE OF SERVICE FOR WHICH THE ITEM IS DESIGNED. 2D MODE REPLY 22AN782AN79 CZMJG 19CLASSIFICATION,LASER LASER CLASSIFICATION INDICATE THE TYPE OF LASER CLASSIFICATION. FULL TEXT WRITE-IN 0 CZMKG 19GRADE RANGE,X-AXIS X-AXIS GRADE RANGE INDICATE THE X-AXIS GRADE RANGE. FULL TEXT WRITE-IN 0 CZMLG 10GRADE RANGE,Y-AXIS Y-AXIS GRADE RANGE INDICATE GRADE RANGE Y-AXIS. FULL TEXT WRITE-IN 0 CZMMJ /D/ 10REACH,HORIZONTAL HORIZONTAL REACH PLEASE USE MRC BCKT IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1B MODE REPLY11AA05 CZMND 18CONNECTIVITY,WIRELESS WIRELESS CONNECTIVITY INDICATES THE TYPE OF WIRELESS CONNECTIVITIES AVAILABLE FOR INPUT/OUTPUT COMMUNICATIONS. SELECT REPLY CODE 10AE79 CZMPA /D/ 12QUANTITY,SUPPORT BAR SUPPORT BAR QUANTITY THE NUMBER OF SUPPORT BARS INCLUDED. 1A MODE REPLY 0 CZMQD 05LOCATION,AXLE AXLE LOCATION INDICATES THE LOCATION OF THE AXLE(S) IN RELATION TO THE ITEM. SELECT REPLY CODE 10AJ91 CZMRJ 04DIAMETER,DRUM PILOT DRUM PILOT DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A DRUM PILOT, AND TERMINATES AT THE CIRCUMFERENCE. 2D AND 1B MODE REPLY21AA051AC20 CZMSJ 10RATING,HUB HUB RATING A MEASUREMENT OF THE LOAD SUPPORTED BY THE HUB. 2D AND 1B MODE REPLY21AA051AC20 CZMTJ 10STANDOUT,WHEEL STUD WHEEL STUD STANDOUT THE DISTANCE MEASURED FROM THE AXLE END MOUNTING SURFACE TO THE FIRST COMPLETE THREAD AT THE OUTSIDE END OF THE STUD. 2D AND 1B MODE REPLY21AA051AC20 CZMUD /D/ 18TYPE FOR WHICH DESIGNED,TARGET TARGET TYPE FOR WHICH DESIGNED INDICATES THE TYPE OF TARGET FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AP85 CZMVJ /D/ 04LENGTH,OVERALL,SLAT SLAT OVERALL LENGTH THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS OF THE SLAT, WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM. 2D AND 1B MODE REPLY21AA051AC20 CZMWJ /D/ 04WIDTH,OVERALL,SLAT SLAT OVERALL WIDTH AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SLAT. 2D AND 1B MODE REPLY21AA051AC20 CZMXA /D/ 12QUANTITY,SLAT SLAT QUANTITY THE NUMBER OF SLATS INCLUDED ON THE ITEM. 1A MODE REPLY 0 CZMYD 05TWIST DIRECTION,WIRE WIRE TWIST DIRECTION THE DIRECTION OF WIRE TWIST SELECT REPLY CODE 10AA38 CZMZJ 04DIAMETER CAPACITY,WIRE WIRE DIAMETER CAPACITY THE DIAMETER OF WIRE ACCOMMODATED. 2D AND 1B MODE REPLY21AA051AC20 CZNAA /D/ 19STANDARD,FLAMMABILITY FLAMMABILITY STANDARD FEDERAL MOTOR VEHICLE SAFETY STANDARDS (FMVSS) FOR THE ITEM. 1A MODE REPLY 0 CZNBJ 10CUTTING SPEED IN STROKES PER MINUTE CUTTING SPEED IN STROKES PER MINUTE THE SPEED OF THE CUTTER EXPRESSED IN STROKES PER MINUTE. 1D AND 1B MODE REPLY11AC20 CZNCJ 04MINIMUM CUTTING RADIUS MINIMUM CUTTING RADIUS THE SMALLEST RADIUS THAT THE ITEM CAN CUT. 1D AND 1B MODE REPLY11AA05 CZNDA 12SETTINGS,HEAT HEAT SETTINGS THE NUMBER OF HEAT SETTINGS PROVIDED WITH THE ITEM. 1A MODE REPLY 0 CZNEJ /D/ 04LENGTH,PLATE,MOUNTING MOUNTING PLATE LENGTH THE MAXIMUM MEASUREMENT OF THE LONGEST DIMENSION OF A MOUNTING PLATE,IN DISTINCTION FROM WIDTH. USE MRC AAXE - WITH ISAC CODING FROM TABLE 0315. 2D AND 1B MODE REPLY21AA051AC20 CZNFA 19NUMBER,COLOR CHIP COLOR CHIP NUMBER THE IDENTIFYING NUMBER FOR THE COLOR CHIP. 1A MODE REPLY 0 CZNGJ A12QUANTITY PER UNIT OF MEASURE,FIN FIN QUANTITY PER UNIT OF MEASURE THE SIZE FIN THE COMB IS CAPABLE OF HANDLING 1D AND 1A MODE REPLY11AB39 CZNHJ 10POINT SPREAD POINT SPREAD THE DISTANCE THE POINT IS CAPABLE OF SPREADING. 2D AND 1B MODE REPLY21AA051AC20 CZNJA 12QUANTITY,LEAF LEAF QUANTITY THE NUMBER OF LEAFS. 1A MODE REPLY 0 CZNKA /D/ 10DEPTH,TREAD TREAD DEPTH MEASUREMENT OF THE DEPTH OF THE TREAD 1A MODE REPLY 0 CZZCA 19BLOCK IDENTIFIER,TERMINAL TERMINAL BLOCK IDENTIFIER A COMBINATION OF LETTERS AND/OR NUMBERS THAT IDENTIFY THE TERMINAL BLOCK LOCATION. 1A MODE REPLY 0 CZZZA 19CAPACITY,MEMORY MEMORY CAPACITY THE AMOUNT OF SPACE AVAILABLE FOR STORAGE OF INFORMATION. 1A MODE REPLY 0 DAAAA 19NATIONAL STOCK NUMBER,WHEEL ASSEMBLY WHEEL ASSEMBLY NATIONAL STOCK NUMBER THE NATIONAL STOCK NUMBER THAT DESIGNATES THE WHEEL ASSEMBLY. 1A MODE REPLY 0 DAABA 19NATIONAL STOCK NUMBER,ONE PIECE RIM ONE PIECE RIM NATIONAL STOCK NUMBER THE NATIONAL STOCK NUMBER THAT DESIGNATES THE ONE PIECE RIM. 1A MODE REPLY 0 DAACA 19NATIONAL STOCK NUMBER,INNER RIM INNER RIM NATIONAL STOCK NUMBER THE NATIONAL STOCK NUMBER THAT DESIGNATES THE INNER RIM. 1A MODE REPLY 0 DAADA 19NATIONAL STOCK NUMBER,OUTER RIM OUTER RIM NATIONAL STOCK NUMBER THE NATIONAL STOCK NUMBER THAT DESIGNATES THE OUTER RIM. 1A MODE REPLY 0 DAAEA 19NATIONAL STOCK NUMBER,TIRE TIRE NATIONAL STOCK NUMBER THE NATIONAL STOCK NUMBER THAT DESIGNATES THE TIRE. 1A MODE REPLY 0 DAAFA /D/ 19ASSEMBLY SIZE,WHEEL,TIRE TIRE WHEEL ASSEMBLY SIZE THE NATIONAL STOCK NUMBER THAT DESIGNATES THE TIRE/WHEEL ASSEMBLY. 1A MODE REPLY 0 DAAGA 03DESIGNATION,TIRE VALVE TIRE VALVE DESIGNATION THE SIZE DESIGNATION OF THE TIRE VALVE. 1A MODE REPLY 0 DAAHD 18CATEGORY,ITEM TYPE ITEM TYPE CATEGORY THE CATEGORY THAT IDENTIFIES THE TYPE OF ITEM. SELECT REPLY CODE 10TC01 DAAJD 18TYPE,ACCESSORY ACCESSORY TYPE THE CATEGORY THAT IDENTIFIES THE TYPE OF ACCESSORY. SELECT REPLY CODE 10AC47 DBBBD /D/ 16TYPE,POINTER POINTER TYPE INDICATES THE TYPE OF POINTER TYPE SELECT REPLY CODE 10AB87 DBBCA /D/ 15INSERT DESIGNATION AND RATING STANDARD INSERT DESIGNATION AND RATING STANDARD INDICATES THE TYPE OF INSERT DESIGNATION AND RATING STANDARD 1A MODE REPLY 0 DDACA 19CODE,AMMUNITION,DOD DOD AMMUNITION CODE A NINE /9/ CHARACTER SEMISIGNIFICANT NUMBER DIVIDED INTO TWO PARTS BY A HYPHEN CENTRALLY ASSIGNED TO GENERIC DESCRIPTIONS APPLICABLE TO ITEMS OF SUPPLY IN FSG 13 AND 14. 1A MODE REPLY 0 DDDDD /D/ 18TYPE,UNDERGARMENT,UPPER UPPER UNDERGARMENT TYPE INDICATES THE TYPE OF UNDERGARMENT OUTFIT FOR WOMEN. USE MRC APGF ISAC TO TABLE 0209 USE REPLY UPPER UNDERGARMENT SELECT REPLY CODE 10AK54 DDDED /D/ 18TYPE,UNDERGARMENT,LOWER LOWER UNDERGARMENT TYPE INDICATES THE TYPE OF UNDERGARMENT OUTFIT FOR WOMEN. USE MRC APGF ISAC TO TABLE 0209 USE REPLY LOWER UNDERGARMENT SELECT REPLY CODE 10AK54 DDDFD /D/ 19SUPRESSION AGENT,FIRE FIRE SUPRESSION AGENT INDICATES THE TYPE OF FIRE SUPPRESSION AGENT SELECT REPLY CODE 10AG54 DENNA 19NUMBER,IDENTIFICATION,DOT DOT IDENTIFICATION NUMBER THE IDENTIFICATION NUMBER ASSIGNED BY THE DEPARTMENT OF TRANSPORTATION (DOT) TO EACH PROPER SHIPPING NAME. IDENTIFICATION NUMBERS PRECEDED BY THE LETTERS "UN" ARE ASSOCIATED WITH INTERNATIONAL AS WELL AS DOMESTIC TRANSPORTATION AND THOSE PRECEDED BY THE LETTERS "NA" ARE NOT RECOGNIZED FOR INTERNATIONAL TRANSPORTATION OF HAZARDOUS MATERIALS (DANGEROUS GOODS) EXCEPT TO AND FROM THE UNITED STATES AND CANADA. 1A MODE REPLY 0 DERMD 19POTENTIAL,LEVEL OF DERMAL IRRITATION LEVEL OF DERMAL IRRITATION POTENTIAL AN INDICATION OF THE LEVEL OF POTENTIAL FOR ADVERSE SKIN REACTIONS FROM DERMAL EXPOSURE TO A PRODUCT. SELECT REPLY CODE 10DE01 DESTJ 10STRENGTH,DIELECTRIC DIELECTRIC STRENGTH THE VALUE,OR RANGE OF VALUES OF THE ELECTRICAL FIELD(S) THAT THE MATERIAL CAN WITHSTAND UNDER IDEAL CONDITIONS WITHOUT UNDERGOING ELECTRICAL BREAKDOWN AND BECOMING ELECTRICALLY CONDUCTIVE. 2D AND 1B MODE REPLY21AB631AC20 DLUMJ /D/ 04DISTANCE,ILLUMINATION ILLUMINATION DISTANCE INDICATES THE DISTANCE AT WHICH THE ITEM IS VISIBLE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 DMTRJ 04DIAMETER DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 DPTHJ 04DEPTH DEPTH A MEASUREMENT BETWEEN SPECIFIED POINTS ON AN ITEM, IN DISTINCTION FROM HEIGHT. 1D AND 1B MODE REPLY11AA05 DPTSJ 10PENETRATION PER STEP,DEPTH DEPTH PENETRATION PER STEP THE DISTANCE IN DEPTH THE CUTTER PENERTRATES PER STEP 2D AND 1B MODE REPLY21AA051AC20 DTFRJ /D/ 10RATE,TRANSFER,DATA DATA TRANSFER RATE THE RATE AT WHICH DATA CAN BE TRANSFERRED FROM ONE SOURCE TO ANOTHER. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1D AND 1B MODE REPLY12AG20 DTRCA 19CODE,REGISTRATION,DOT DOT REGISTRATION CODE AN ALPHA-NUMERIC CODE ASSIGNED BY THE DEPARTMENT OF TRANSPORTATION IDENTIFYING THE FINAL HAZARD CLASSIFICATION. 1A MODE REPLY 0 DTRGJ 10RANGE,DETECTION DETECTION RANGE THE MINIMUM AND THE MAXIMUM VALUES REPRESENTING THE DETECTION RATE OF THE ITEM 2D AND 1B MODE REPLY21AA051AC20 ECATD 03ENVIRONMENTAL ATTRIBUTE CATEGORY ENVIRONMENTAL ATTRIBUTE CATEGORY THE CATEGORY THAT DEFINES THIS ITEM'S ENVIRONMENTAL ATTRIBUTE. SELECT REPLY CODE 10EN02 ECPGD /D/ 19ITEM,COMPREHENSIVE PROCUREMENT GUIDELINE,EPA EPA COMPREHENSIVE PROCUREMENT GUIDELINE ITEM INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE ENVIRONMENTAL PROTECTION AGENCY (EPA) COMPREHENSIVE PROCUREMENT GUIDELINES (CPG) - RECOVERED MATERIALS ADVISORY NOTICES (RMAN. SELECT REPLY CODE 10EP00 ECWTJ /D/ 10WEIGHT,CONTAINER,EXTERIOR EXTERIOR CONTAINER WEIGHT THE MEASURED WEIGHT OF THE EXTERIOR CONTAINER. PLEASE USE MRC AJWK WITH ISAC CODING OF OUTER CONTAINER IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1B MODE REPLY12AN75 EEPGD /D/ 18TYPE,PRODUCT,ENERGY EFFICIENT ENERGY EFFICIENT PRODUCT TYPE INDICATES THE TYPE OF ENERGY EFFICIENT PRODUCT FOR WHICH THE DEPARTMENT OF ENERGY (DOE) HAS PUBLISHED A PRODUCT ENERGY EFFICIENCY RECOMMENDATION AND WHICH MEETS OR EXCEEDS THE RECOMMENDED DOE EFFICIENCY. SELECT REPLY CODE 10EE00 ELCDD 15EXTRA LONG CHARACTERISTIC DESCRIPTION EXTRA LONG CHARACTERISTIC DESCRIPTION A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS. SELECT REPLY CODE 10AN58 ELECB 10VOLTAGE IN VOLTS VOLTAGE IN VOLTS THE TOTAL ELECTRICAL VOLTAGE. 1B MODE REPLY 0 ELRNG 15EXTRA LONG REFERENCE NUMBER EXTRA LONG REFERENCE NUMBER A REFERENCE NUMBER EXCEEDING 32 POSITIONS. FULL TEXT WRITE-IN 0 ENACD 07CODE,ATTRIBUTE,ENVIRONMENTAL ENVIRONMENTAL ATTRIBUTE CODE INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS. SELECT REPLY CODE 10EN02 ENVAD /D/ 19ATTRIBUTE,ENVIRONMENTAL ENVIRONMENTAL ATTRIBUTE THE SPECIFIC ATTRIBUTE OF THE ITEM THAT QUALIFIES IT AS AN ENVIRONMENTALLY PREFERABLE PRODUCT. SELECT REPLY CODE 10EN00 EPDGD /D/ 18TYPE,DESIGNATED GUIDELINE ITEM,EPA EPA DESIGNATED GUIDELINE ITEM TYPE INDICATES THE TYPE OF ENVIRONMENTAL PROTECTION AGENCY (EPA) DESIGNATED GUIDELINE ITEM. SELECT REPLY CODE 10EP00 EPPCD /D/ 18TYPE,CERTIFICATION,ENVIRONMENTALLY PREFERRED PRODUCT ENVIRONMENTALLY PREFERRED PRODUCT CERTIFICATION TYPE INDICATES THE TYPE OF CERTIFICATION INDICATING THE ITEM IS AN ENVIRONMENTALLY PREFERRED PRODUCT. SELECT REPLY CODE 10EN01 EXDEJ /D/ 04DEPTH,EXTENDED EXTENDED DEPTH A LINEAR MEASUREMENT FROM THE SURFACE TO A SPECIFIED INNER POINT ON AN ITEM WHEN IT IS IN AN EXTENDED POSITION, IN DISTINCTION FROM HEIGHT. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 EXMEJ /D/ 10MEASURE,CUBIC,CONTAINER,EXTERIOR EXTERIOR CONTAINER CUBIC MEASURE A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF THE EXTERIOR CONTAINER AND RENDERED IN CUBIC UNITS. 1D AND 1B MODE REPLY12AN76 EXQTA /D/ 12QUANTITY,CONTAINER,EXTERIOR EXTERIOR CONTAINER QUANTITY THE NUMBER OF UNITS OF ISSUE PLACED INSIDE THE EXTERIOR CONTAINER. PLEASE USE MRC NMBR WITH ISAC CODING OF OUTER CONTAINER IN PLACE OF THIS DISCONTINUED MRC. 1A MODE REPLY 0 EXWTJ 10WEIGHT,EXPLOSIVE,NET NET EXPLOSIVE WEIGHT THE NET WEIGHT OF THE EXPLOSIVE CONTENT OF THE ITEM FOR TRANSPORTATION AND/OR STORAGE. 2D AND 1B MODE REPLY23AH212AG67 FAAZD 10PHASE PHASE THE NUMBER OF ALTERNATING CURRENT PHASES. SELECT REPLY CODE 10AD02 FAMEJ 10MAXIMUM FATTY ACID METHYL ESTER (FAME) CONTENT IN MILLIGRAMS PER KILOGRAM MAXIMUM FATTY ACID METHYL ESTER (FAME) CONTENT IN MILLIGRAMS PER KILOGRAM DEFINES THE FATTY ACID METHYL ESTER CONTENT FOR JET FUEL. 2D AND 1B MODE REPLY22AN751AC20 FCLSA 19CLASSIFICATION,FUNCTIONAL FUNCTIONAL CLASSIFICATION THE ALPHA-NUMERIC DESIGNATION THAT IDENTIFIES THE CLASSIFICATION OF THE ITEM ACCORDING TO THE CATEGORY OF FUNCTIONS PERFORMED. 1A MODE REPLY 0 FCRAJ T10RANGE,FOCUSING FOCUSING RANGE THE MINIMUM AND MAXIMUM DISTANCE THE ITEM CAN BE FOCUSED. 1D AND 1F MODE REPLY11AA05 FEATG 15SPECIAL FEATURES SPECIAL FEATURES THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS. FULL TEXT WRITE-IN 0 FFWDD /D/ 19FOOD FOR WHICH DESIGNED FOOD FOR WHICH DESIGNED THE FOOD FOR WHICH THE ITEM IS DESIGNED. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AE92 FGRAD /D/ 19GOVERNMENT/AGENCY,FOREIGN,CONTROLLING CONTROLLING FOREIGN GOVERNMENT/AGENCY THE NAME OF THE FOREIGN COUNTRY OR AGENCY CONTROLLING THE ITEM. SELECT REPLY CODE 10AN85 FLEXD 07FLEXIBILITY FLEXIBILITY FLEXIBLE,CAPABLE OF BEING BENT,TURNED OR TWISTED,WITHIN LIMITS,WITHOUT BREAKING,OR RIGID,RESISTING CHANGE OF FORM,INFLEXIBLE. SELECT REPLY CODE 10AD03 FMATD 09MATERIAL,FIBER FIBER MATERIAL THE ELEMENT,CHEMICAL COMPOUND,OR MECHANICAL MIXTURE PROPERTIES OF THE FIBER,OR THE GENERIC NAME BY WHICH THE MANUFACTURED FIBER IS KNOWN AND/OR IDENTIFIED. SELECT REPLY CODE 10MA02 FMDCJ A19DOCUMENT AND CLASSIFICATION,MATERIAL,FIBER FIBER MATERIAL DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS CLASS,CONDITION,TEMPER,AND THE LIKE,THAT IDENTIFIES THE FIBER MATERIAL. 2D AND 1A MODE REPLY21AP331AP18 FRAAG /D/ 19PARTS,AUXILIARY AUXILIARY PARTS SUCH PARTS AS NUTS,WASHERS,PINS,AND THE LIKE,WHICH ARE COMPONENTS OF THE ITEM OF SUPPLY AND ARE INTENDED TO BE USED WITH THE MAIN COMPONENT ITEM. FULL TEXT WRITE-IN 0 FREQB 10FREQUENCY IN HERTZ FREQUENCY IN HERTZ THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT. 1B MODE REPLY 0 FTLDG 19DESCRIPTION,FUNCTIONAL FUNCTIONAL DESCRIPTION DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED. FULL TEXT WRITE-IN 0 FUELD 18TYPE,FUEL FUEL TYPE INDICATES THE TYPE OF FUEL(S) FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AF80 FUSED /D/ 07FUSE,PROTECTION,CIRCUIT CIRCUIT PROTECTION FUSE INDICATES WHETHER THE ITEM IS FUSED OR UNFUSED. SELECT REPLY CODE 10AB22 FVPCD /D/ 10VOLUME PER CYCLE,FLUID FLUID VOLUME PER CYCLE THE MEASUREMENT OF THE VOLUME OF FLUID USED PWE EACH CYCLE OF THE ITEM. SELECT REPLY CODE 10AD42 GRAAD /D/ 09MATERIAL,FILM,CONDUCTIVE CONDUCTIVE FILM MATERIAL AN INDICATION OF THE MATERIAL APPLIED TO THE ITEM AS A CONDUCTIVE FILM. SELECT REPLY CODE 10AD09 GRABB 10TEMP IN DEG CELSIUS,SURFACE,MAXIMUM MAXIMUM SURFACE TEMP IN DEG CELSIUS THE MAXIMUM PERMISSIBLE TEMPERATURE AT THE SURFACE OF THE ITEM,EXPRESSED IN DEGREES CELSIUS. 1B MODE REPLY 0 GRACB 10VOLTAGE IN VOLTS,PERMANENT,MAXIMUM MAXIMUM PERMANENT VOLTAGE IN VOLTS THE MAXIMUM DIRECT OR ROOT MEAN SQUARE ALTERNATING CURRENT VOLTAGE THAT CAN BE PERMANENTLY APPLIED TO THE TERMINALS OF THE ITEM,EXPRESSED IN VOLTS. 1B MODE REPLY 0 GRADB /D/ 10VOLTAGE IN KILOVOLTS,BREAKDOWN BREAKDOWN VOLTAGE IN KILOVOLTS THE VOLTAGE AT WHICH THE INSULATION MATERIAL OF THE ITEM WILL FAIL TO WITHSTAND AND AT WHICH AN ELECTRIC BREAKDOWN MAY OCCUR,EXPRESSED IN KILOVOLTS. 1B MODE REPLY 0 GRAEJ 10RESISTANCE,INSULATION INSULATION RESISTANCE THE ELECTRICAL RESISTANCE VALUE MEASURED AT NORMAL ENVIRONMENTAL CONDITIONS BETWEEN THE INTERCONNECTER TERMINALS AND THE PERIPHERAL METALLIC PARTS OF A RESISTOR. 2D AND 1B MODE REPLY22AN861AC20 GRAFB 10VOLTAGE IN MICROVOLTS PER VOLT,CURR ENT NOISE,MAXIMUM MAXIMUM CURR ENT NOISE VOLTAGE IN MICROVOLTS PER VOLT THE PORTION OF THE NOISE VOLTAGE CAUSED AT THE TERMINALS BY THE FLOW OF DIRECT CURRENT PASSING THROUGH THE ITEM,EXPRESSED IN MICROVOLTS PER VOLT. 1B MODE REPLY 0 GRAGB /D/ 10RATIO IN DECIBELS,HARMONIC DISTORTION,MINIMUM MINIMUM HARMONIC DISTORTION RATIO IN DECIBELS THE PORTION OF THE DOMINANT WAVE VOLTAGE HAVING THE FREQUENCY OF A SINUSOIDAL CURRENT IN RELATION TO THE ELECTROMOTIVE FORCE HAVING THE THREEFOLD FREQUENCY OF THE SINUSOIDAL CURRENT,EXPRESSED IN DECIBELS. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1B MODE REPLY 0 GRAHB 10STRENGTH IN NEWTONS,TENSILE,TERMINAL TERMINAL TENSILE STRENGTH IN NEWTONS THE MAXIMUM LOAD IN TENSION THAT CAN BE APPLIED TO THE TERMINALS OF THE ITEM,EXPRESSED IN NEWTONS. 1B MODE REPLY 0 GRAJD 19MARKINGS MARKINGS THE HUE,TINT,LETTERS,NUMBERS,AND/OR SYMBOLS INCLUDED ON THE ITEM FOR IDENTIFICATION. SELECT REPLY CODE 10AP34 GRAKB /D/ 04SPACING IN MILLIMETERS,GRID,STANDARD STANDARD GRID SPACING IN MILLIMETERS AN INDICATION OF THE STANDARD GRID SPACING FOR WHICH THE ITEM IS DESIGNED,EXPRESSED IN MILLIMETERS. 1B MODE REPLY 0 GRALJ /D/ 10VOLTAGE PER SECTION IN VOLTS,PERMANENT,MAXIMUM MAXIMUM PERMANENT VOLTAGE PER SECTION IN VOLTS THE MAXIMUM VOLTAGE THAT MAY BE PERMANENTLY APPLIED BETWEEN THE TERMINALS OF EACH SECTION,EXPRESSED IN VOLTS. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1D AND 1B MODE REPLY12AH19 GRAMB /D/ 10VOLTAGE IN VOLTS,INSULATION,PERMANENT,MAXIMUM MAXIMUM PERMANENT INSULATION VOLTAGE IN VOLTS THE MAXIMUM PERMISSIBLE PERMANENT VOLTAGE THAT CAN BE APPLIED BETWEEN THE INTERCONNECTED TERMINALS OF THE RESISTOR AND THE METALLIC MOUNTING FACILITIES WITHOUT THE RISK OF ELECTRIC FLASHOVER,EXPRESSED IN VOLTS. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1B MODE REPLY 0 GRANJ 10RESISTANCE,INSULATION INSULATION RESISTANCE THE ELECTRICAL RESISTANCE VALUE MEASURED BETWEEN THE INTERCONNECTED TERMINALS OF THE RESISTOR AND THE METALLIC MOUNTING FACILITIES. 2D AND 1B MODE REPLY22AN861AC20 GRAPB /D/ 10RESISTANCE IN OHMS,NOISE,EQUIVALENT EQUIVALENT NOISE RESISTANCE IN OHMS THE TRANSIENT RESISTANCE APPEARING BETWEEN THE CONTACT AND THE RESISTANCE ELEMENT WHEN THE SHAFT IS ROTATED OR TRANSLATED,EXPRESSED IN OHMS. 1B MODE REPLY 0 GRAQB /D/ 10VOLTAGE IN MILLIVOLTS,NOISE,DYNAMIC DYNAMIC NOISE VOLTAGE IN MILLIVOLTS THE VOLTAGE APPEARING BETWEEN THE CONTACT AND THE RESISTANCE ELEMENT WHEN THE SHAFT IS ROTATED OR TRANSLATED,EXPRESSED IN MILLIVOLTS. 1B MODE REPLY 0 GRARA 19CLASS,APPLICABILITY APPLICABILITY CLASS AN INDICATION OF THE MINIMUM AND MAXIMUM OPERATING TEMPERATURES AND THE HUMIDITY LOAD OF AN ELECTRICAL COMPONENT. 1A MODE REPLY 0 GRASA /D/ 10WEIGHT IN GRAMS PER SQUARE METER,BACKING,PAPER PAPER BACKING WEIGHT IN GRAMS PER SQUARE METER THE MEASURED WEIGHT OF THE PAPER BACKING; I.E.,ITS WEIGHT WITH REFERENCE TO SURFACE,EXPRESSED IN GRAMS PER SQUARE METER. 1A MODE REPLY 0 GRSQA /D/ 12QUANTITY,SURFACE,GRATING GRATING SURFACE QUANTITY THE NUMBER OF GRATING SURFACES INCLUDED ON THE ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1A MODE REPLY 0 GRWTJ 10WEIGHT,GROSS GROSS WEIGHT THE COMBINED WEIGHT OF THE ITEM AND ITS LOADED CONTENTS. 2D AND 1B MODE REPLY22AD282AG67 HAZDA 19CLASS/DIVISION,HAZARD,DOT DOT HAZARD CLASS/DIVISION A DESIGNATION OF THE HAZARD CLASS OR DIVISION CORRESPONDING TO EACH PROPER SHIPPING NAME FOR HAZARDOUS MATERIAL AS IDENTIFIED BY THE DEPARTMENT OF TRANSPORTATION (DOT) AND LISTED IN THE TITLE 49 CODE OF FEDERAL REGULATIONS (CFR), PART 172, HAZARDOUS MATERIALS TABLE. 1A MODE REPLY 0 HDCLJ A19DOCUMENT AND CLASSIFICATION,COLOR COLOR DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,MANUFACTURERS REFERENCE,OR INDEX SYSTEM AND THE CLASIFICATION DESIGNATION, USED TO IDENTIFY COLOR, COLOR SELECTION, COLOR MATCHING AND QUALITY CONTROL OF A SPECIFIC COLOR. 2D AND 1A MODE REPLY21AP331AP93 HEATD 06HEAT TREATMENT HEAT TREATMENT A COMBINATION OF TIMED HEATING AND COOLING OPERATIONS APPLIED FOR THE PURPOSE OF ANNEALING OR HARDENING THE ITEM. SELECT REPLY CODE 10AD05 HGTHJ 04HEIGHT HEIGHT A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN OBJECT,IN DISTINCTION FROM DEPTH. 2D AND 1B MODE REPLY21AA051AC20 HHHHJ 10BANDPASS,FREQUENCY FREQUENCY BANDPASS WIDTH OF THE BANDPASS BETWEEN THE LOW CUTOFF FREQUENCY AND THE HIGH CUTOFF FREQUENCY OF THE FILTER. 1D AND 1B MODE REPLY11AC32 HMCCJ A19CODE,CLASSIFICATION,MATERIAL,HAZARDOUS HAZARDOUS MATERIAL CLASSIFICATION CODE AN ALPHA-NUMERIC CODE IDENTIFYING A GROUP OR CLASSIFICATION OF VARIOUS MATERIALS AS TO THEIR POTENTIAL TO CAUSE EXPLOSIONS,FIRES OR DAMAGE BY CHEMICAL ACTION. 1D AND 1A MODE REPLY12AP66 HRLCJ /D/ 10HARDNESS RATING AND LOCATION HARDNESS RATING AND LOCATION A NUMERIC VALUE,USED IN CONJUNCTION WITH A HARDNESS RATING SCALE,DESIGNATING THE SPECIFIC HARDNESS OF AN ITEM AND THE LOCATION. 3D AND 1B MODE REPLY32AC261AC203AN73 HUESD 01COLOR COLOR A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY. SELECT REPLY CODE 10AD06 HYSTG /D/ 19DATA,CHARACTERISTICS,ARCHIVED ARCHIVED CHARACTERISTICS DATA IDENTIFICATION AND RETENTION OF CHARACTERISTICS DATA NO LONGER USED IN THE CURRENT DESCRIPTION OF AN ITEM OF SUPPLY. MRC IS RESTRICTED TO INTERNAL DLSC CHARACTERISTICS MASS CHANGE PROCESSING. FULL TEXT WRITE-IN 0 HZRDD 19SUBSTANCES,HAZARDOUS HAZARDOUS SUBSTANCES THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY. SELECT REPLY CODE 10HZ00 KRLCH 01COLOR AND LOCATION COLOR AND LOCATION A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY,AND ITS LOCATION ON THE ITEM. 2D MODE REPLY 26AD063AN73 KZTSD 19SERVICE,COGNIZANT COGNIZANT SERVICE THE MILITARY SERVICE THAT INITIALLY PROCURED THE ITEM FROM THE CONTRACTOR. SELECT REPLY CODE 10AP57 LAAAJ /D/ 04DISTANCE BETWEEN SHOCK CENTERS DISTANCE BETWEEN SHOCK CENTERS INDICATES THE DISTANCE BETWEEN SHOCK CENTERS. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 LAABJ /D/ 04DISTANCE BETWEEN KING PIN CENTERS DISTANCE BETWEEN KING PIN CENTERS INDICATES THE DISTANCE BETWEEN KING PIN CENTERS. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 LAACJ 04DISTANCE BETWEEN HUB FACE TO HUB FACE DISTANCE BETWEEN HUB FACE TO HUB FACE INDICATES THE DISTANCE BETWEEN HUB FACE TO HUB FACE. 2D AND 1B MODE REPLY21AA051AC20 LABMD 11METHOD,LABELING LABELING METHOD THE MEANS OF LABELING THE ITEM. SELECT REPLY CODE 10AN32 LAQSJ 12LENGTH AND QUANTITY,SLOT SLOT LENGTH AND QUANTITY THE DISTANCE MEASURED ALONG A STRAIGHT LINE PERPENDICULAR TO THE LONGITUDINAL AXIS OF THE SLOT FROM ONE EDGE TO THE OTHER. 3D AND 1B MODE REPLY31AA051AC203AP65 LBLCA /D/ 03CODE,DOT LABEL DOT LABEL CODE AN ALPHA-NUMERIC CODE IDENTIFYING THE TYPE OF LABEL REQUIRED BY THE DEPARTMENT OF TRANSPORTATION. CANCLED WITH NO REPLACEMENT - THIS INFORMATION IS NOT CHARACTERISTIC INFORMATION, THIS INFORMATION NEEDS TO BE INPUT IN SEG G OF THE TIR. 1A MODE REPLY 0 LBMAD 09MATERIAL,LUBRICATION LUBRICATION MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES WITH WHICH THE ITEM IS LUBRICATED. SELECT REPLY CODE 10MA01 LDWTJ 10LANDING WEIGHT LANDING WEIGHT THE MAXIMUM AIRCRAFT WEIGHT PERMITTED FOR LANDING. 2D AND 1B MODE REPLY22AG671AC20 LENLJ 04LENGTH,LEDGE NUT LEDGE NUT LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF THE NUT FROM THE FLANGE TO THE END IN DISTINCTION FROM WIDTH. 2D AND 1B MODE REPLY21AA051AC20 LGTHJ 04LENGTH LENGTH A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH. 1D AND 1B MODE REPLY11AA05 LMDCJ A19DOCUMENT AND CLASSIFICATION,MATERIAL,LUBRICATION LUBRICATION MATERIAL DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS CLASS,CONDITION,TEMPER,AND THE LIKE,THAT IDENTIFIES THE LUBRICATION MATERIAL. 2D AND 1A MODE REPLY21AP331AP18 MALCH /D/ 09MATERIAL AND LOCATION MATERIAL AND LOCATION THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED,AND ITS LOCATION. PLEASE USE MRC MATT WITH ISAC CODING IN REPLACE OF THIS DISCONTINUED MRC. 2D MODE REPLY 26MA013AN73 MARKG 19MARKINGS,SPECIAL SPECIAL MARKINGS MARKINGS INCLUDED ON AN ITEM FOR THE PURPOSE OF OFFERING INSTRUCTIONS OR WARNINGS OR TO INDICATE THE PURPOSE,FUNCTION,OR APPLICATION OF THE ITEM.EXCLUDES MANUFACTURERS PART NUMBERS,SYMBOLS,OR THE LIKE. FULL TEXT WRITE-IN 0 MASUD 09MATERIAL,INSULATION INSULATION MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE INSULATION IS FABRICATED. SELECT REPLY CODE 10MA01 MATLD /D/ 09MATERIAL MATERIAL THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH AN ITEM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT. PLEASE USE MRC MATT IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 MATTD 09MATERIAL MATERIAL THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED. SELECT REPLY CODE 10MA01 MDAPH /D/ 09MATERIAL/DOCUMENT AND PRECEDENCE MATERIAL/DOCUMENT AND PRECEDENCE THE GENERIC NOUN OF THE MATERIAL OF WHICH THE ITEM IS FABRICATED,THE GOVERNING DOCUMENT AND THE ORDER OF PRECEDENCE. 2D MODE REPLY 21AP186AD09 MDCDJ /D/A03DESIGNATION,CLASSIFICATION,MATERIAL DOCUMENT MATERIAL DOCUMENT CLASSIFICATION DESIGNATION THE DESIGNATION THAT IDENTIFIES THE PHYSICAL PRIORITIES,CONDITIONS,ETC,OF THE MATERIAL AS EXPRESSED BY THE GOVERNING DOCUMENT. 2D AND 1A MODE REPLY21AP182AD08 MDCLJ A19DOCUMENT AND CLASSIFICATION,MATERIAL MATERIAL DOCUMENT AND CLASSIFICATION THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL. 2D AND 1A MODE REPLY21AP331AP18 MDCPH /D/ 09MATERIAL/DOCUMENT/COMPOSITION AND PRECEDENCE MATERIAL/DOCUMENT/COMPOSITION AND PRECEDENCE THE GENERIC NOUN OF THE BASIC MATERIAL OF WHICH THE ITEM IS FABRICATED,THE GOVERNING DOCUMENT,THE CHEMICAL ANALYSIS DESIGNATOR,SUCH AS ALLOY,CLASS,COMPOSITION,GRADE OR TYPE,AND THE ORDER OF PRECEDENCE. 2D MODE REPLY 21AP186AD09 MDESD 03DESIGNATION AND GRADE,MEDICAL MEDICAL DESIGNATION AND GRADE MEDICAL DESIGNATION AND GRADE OR QUALITY OF THE SOLUTE SELECT REPLY CODE 10AP92 MEDAD 19MEDIA FOR WHICH DESIGNED MEDIA FOR WHICH DESIGNED THE TYPE OF MEDIA FOR WHICH THE ITEM IS DESIGNED. SELECT REPLY CODE 10AN91 MERDD 11METHOD READER METHOD READER INDICATES THE TYPE OF METHOD READER. SELECT REPLY CODE 10AJ42 MLLCH /D/ 09MATERIAL AND LOCATION MATERIAL AND LOCATION THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ITEM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT,AND ITS LOCATION. 2D MODE REPLY 26AD093AN73 MPCTJ /D/ 09MATERIAL AND PERCENTAGE,ADDITIVE ADDITIVE MATERIAL AND PERCENTAGE INDICATES THE MATERIAL AND ITS PERCENTAGE. 1D AND 1B MODE REPLY16MA01 MRKCA /D/ 03CODE,DOT MARKING DOT MARKING CODE AN ALPHA CODE IDENTIFYING THE MARKINGS FOR TRANSPORTATION AND/OR STORAGE OF HAZARDOUS MATERIALS APPROVED BY THE DEPARTMENT OF TRANSPORTATION. 1A MODE REPLY 0 MTLCH /D/ 09MATERIAL AND LOCATION MATERIAL AND LOCATION THE ELEMENT,COMPOUND,OR MIXTURE OF WHICH THE ITEM IS FABRICATED,EXCLUDING ANY SURFACE TREATMENT,AND ITS LOCATION. PLEASE USE MRC MALC IN PLACE OF THIS DISCONTINUED MRC. 2D MODE REPLY 23AN736AD09 NAACA 19CODE,AMMUNITION AMMUNITION CODE A SIGNIFICANT CODE CONSISTING OF A COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS ASSIGNED TO ITEMS OF SUPPLY IN FSG 13 AND 14. IDENTICAL CODES SIGNIFY FUNCTIONALLY INTERCHANGEABLE ITEMS FOR ISSUE AND USE. 1A MODE REPLY 0 NAMED /D/ 15ITEM NAME ITEM NAME A NOUN,WITH OR WITHOUT MODIFIERS,BY WHICH AN ITEM OF SUPPLY IS KNOWN. SELECT REPLY CODE 10AD11 NBUSJ A12USES,NUMBER OF NUMBER OF USES THE MANUFACTURES STATED NUMBER OF TIMES AN ITEM CAN BE USED. 1D AND 1A MODE REPLY11AC20 NHCFD 07FEATURE,CRITICAL,NUCLEAR HARDNESS NUCLEAR HARDNESS CRITICAL FEATURE AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM. SELECT REPLY CODE 10AD05 NMBRA 12QUANTITY QUANTITY A NUMERIC VALUE WHICH REPRESENTS A POSITIVE WHOLE VALUE WITHOUT REGARD TO ANY UNIT OF MEASURE. 1A MODE REPLY 0 NRAAJ 04DISTANCE FROM CENTERLINE TO END OF LONGEST KEY DISTANCE FROM CENTERLINE TO END OF LONGEST KEY NONE. 2D AND 1B MODE REPLY21AA051AC20 NRABJ 04DISTANCE FROM CENTERLINE TO END OF SHORTEST KEY DISTANCE FROM CENTERLINE TO END OF SHORTEST KEY NONE. 2D AND 1B MODE REPLY21AA051AC20 NRACJ 04DISTANCE FROM CENTERLINE TO END OF KEY DISTANCE FROM CENTERLINE TO END OF KEY NONE. 2D AND 1B MODE REPLY21AA051AC20 NTAAB /D/ 10CAPACITY IN MILLILITERS,FLUID FLUID CAPACITY IN MILLILITERS THE AMOUNT OF FLUID THE ITEM IS DESIGNED TO HOLD,EXPRESSED IN MILLILITERS. 1B MODE REPLY 0 NTRDA 19DATE,ENTRY ENTRY DATE INDICATES THE DATE THE ITEM WAS ENTERED INTO MIL-HDBK-300. 1A MODE REPLY 0 PEPSD 15PERSONAL EQUIPMENT PERFORMANCE STANDARD PERSONAL EQUIPMENT PERFORMANCE STANDARD INFORMATION SUCH AS TYPE OF MASK, COUNTRY, STANDARD DOCUMENT, PERCENTAGE OF PARTICULATE FILTERED SELECT REPLY CODE 10AJ50 PESPJ 10SPEED,OPERATIONAL OPERATIONAL SPEED THE NARRATIVE EXPRESSION INDICATION THE SPEED AT WHICH THE ITEM OPERATES. 1D AND 1B MODE REPLY11AA34 PGCDA 19PROCUREMENT GROUP CODE PROCUREMENT GROUP CODE A FIVE DIGIT NUMERIC CODE USED TO GROUP INDIVIDUAL SIZES OF A STANDARD GENERIC ITEM. 1A MODE REPLY 0 PJNGJ T04RANGE,PROJECTION PROJECTION RANGE THE MINIMUM AND THE MAXIMUM DISTANCES REPRESENTING THE PROJECTION RATE OF THE ITEM. 1D AND 1F MODE REPLY11AA05 PKDWJ /D/ 10WEIGHT,UNIT,PACKAGED PACKAGED UNIT WEIGHT THE MEASURED WEIGHT OF AN ITEM OF SUPPLY AND ITS CONTAINER. 1D AND 1B MODE REPLY12AN75 PKNDJ /D/ 04DIAMETER,OVERALL,NOMINAL,PACKAGE PACKAGE NOMINAL OVERALL DIAMETER THE NOMINAL MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS THE CIRCULAR CROSS-SECTIONAL PLANE OF THE PACKAGE. CANCLED WITH NO REPLACEMENT - THIS INFORMATION IS NOT CHARACTERIATION NEEDS STIC INFORMATION, THIS INFORMATION NEEDS TO BE INPUT IN SEG W OF THE TIR. 1D AND 1B MODE REPLY11AA05 PKNHJ /D/ 04HEIGHT,OVERALL,NOMINAL,PACKAGE PACKAGE NOMINAL OVERALL HEIGHT THE NOMINAL DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE PACKAGE. CANCLED WITH NO REPLACEMENT - THIS INFORMATION IS NOT CHARACTERISTIC INFORMATION, THIS INFORMATION NEEDS TO BE INPUT IN SEG W OF THE TIR. 1D AND 1B MODE REPLY11AA05 PKNLJ /D/ 04LENGTH,OVERALL,NOMINAL,PACKAGE PACKAGE NOMINAL OVERALL LENGTH THE NOMINAL DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE PACKAGE. CANCLED WITH NO REPLACEMENT - THIS INFORMATION IS NOT CHARACTERISTIC INFORMATION, THIS INFORMATION NEEDS TO BE INPUT IN SEG W OF THE TIR. 1D AND 1B MODE REPLY11AA05 PKNWJ /D/ 04WIDTH,OVERALL,NOMINAL,PACKAGE PACKAGE NOMINAL OVERALL WIDTH THE NOMINAL OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PACKAGE,IN DISTINCTION FROM THICKNESS. CANCLED WITH NO REPLACEMENT - THIS INFORMATION IS NOT CHARACTERISTIC INFORMATION, THIS INFORMATION NEEDS TO BE INPUT IN SEG W OF THE TIR. 1D AND 1B MODE REPLY11AA05 PKQTA /D/ 12QUANTITY,PACKAGE,INTERMEDIATE INTERMEDIATE PACKAGE QUANTITY THE NUMBER OF WRAPS,BOXES,OR BUNDLES,WHICH CONTAINS TWO OR MORE UNITS OF ISSUE,PLACED INSIDE AN EXTERIOR CONTAINER. 1A MODE REPLY 0 PKRNA 19NUMBER,REFERENCE,PACKAGE PACKAGE REFERENCE NUMBER AN ALPHA-NUMERIC CODE IDENTIFYING THE DRAWING AND/OR SPECIFICATION WHICH CONTROLS THE LOADING OF THE PACKAGE. 1A MODE REPLY 0 PKTYD /D/ 18TYPE,PACKAGE,UNIT UNIT PACKAGE TYPE INDICATES THE TYPE OF CONTAINER IN WHICH THE ITEM OF SUPPLY IS PACKAGED. PLEASE USE MRC ALQG IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AN65 PKWTJ /D/ 10WEIGHT,UNIT,UNPACKAGED UNPACKAGED UNIT WEIGHT THE MEASURED WEIGHT OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING MATERIAL. PLEASE USE MRC CTJS IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1B MODE REPLY12AN75 PMLCJ A09MATERIAL AND LOCATION,PRECIOUS PRECIOUS MATERIAL AND LOCATION AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM. 1D AND 1A MODE REPLY16MA01 PMWTJ 09MATERIAL AND WEIGHT,PRECIOUS PRECIOUS MATERIAL AND WEIGHT AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE. 2D AND 1B MODE REPLY26MA011AG14 PPRMB 10PERCENTAGE,MATERIALS,RECOVERED,POST-CONSUMER POST-CONSUMER RECOVERED MATERIALS PERCENTAGE THE PERCENTAGE OF THE POST-CONSUMER RECOVERED OR RECYCLED MATERIAL INCLUDED IN THE ITEM. 1B MODE REPLY 0 PRMTD 09MATERIAL,PRECIOUS PRECIOUS MATERIAL IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM. SELECT REPLY CODE 10MA01 PRNGD 19INGREDIENT,PRIMARY PRIMARY INGREDIENT THE PRIMARY INGREDIENT OF WHICH THE FOOD ITEM IS MADE OF. SELECT REPLY CODE 10AH50 PRPYA 15CHARACTERISTICS,PROPRIETARY PROPRIETARY CHARACTERISTICS IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA. 1A MODE REPLY 0 PTDCJ /D/A19DOCUMENT AND CLASSIFICATION,PRETREATMENT PRETREATMENT DOCUMENT AND CLASSIFICATION THE SPECIFICATION, STANDARD, OR MANUFACTURERS REFERENCE, AND THE CLASSIFICATION DESIGNATION, SUCH AS TYPE, CLASS, GRADE AND THE LIKE, THAT IDENTIFIES THE PRETREATMENT MATERIAL. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1A MODE REPLY21AP331AP39 PTMCD /D/ 09MATERIAL,COATING COATING MATERIAL THE ELEMENT, COMPOUND, OR MIXTURE WITH WHICH THE ITEM IS COATED, EXCLUDING ANY SURFACE TREATMENT. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10SF01 PTPMG /D/ 11METHOD,PREPARATION,PRETREATMENT PRETREATMENT PREPARATION METHOD THE MEANS BY WHICH THE SURFACE IS PREPARED FOR THE SURFACE TREATMENT APLICATION. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. FULL TEXT WRITE-IN 0 PTRMB 10PERCENTAGE,MATERIALS,RECOVERED,TOTAL TOTAL RECOVERED MATERIALS PERCENTAGE THE PERCENTAGE OF THE TOTAL RECOVERED OR RECYCLED MATERIAL, FROM MANUFACTURING PROCESSES OR CONSUMER, INCLUDED IN THE ITEM. 1B MODE REPLY 0 PTRNA 03PART NUMBER,CONDUCTOR CONDUCTOR PART NUMBER THE IDENTIFYING PART NUMBER OF THE WIRE OR CABLE AS ASSIGNED BY THE MANUFACTURER. 1A MODE REPLY 0 PTRPA 03CAGE COMMERCIAL AND GOVERNMENT ENTITY CODE,CONDUCTOR CONDUCTOR CAGE COMMERCIAL AND GOVERNMENT ENTITY CODE THE IDENTIFYING CAGE CODE FOR THE MANUFACTURER OF THE WIRE OR CABLE. 1A MODE REPLY 0 PTRQA 03NATIONAL STOCK NUMBER,CONDUCTOR CONDUCTOR NATIONAL STOCK NUMBER THE IDENTIFYING NATIONAL STOCK NUMBER OF THE WIRE OR CABLE. 1A MODE REPLY 0 QRSTA /D/ 12QUANTITY,TEST MRC TEST MRC QUANTITY TEST MRC 1A MODE REPLY 0 QTSCA /D/ 12QUANTITY PER SHIPPING CONTAINER QUANTITY PER SHIPPING CONTAINER THE NUMBER OF ITEMS PER SHIPPING CONTAINER. CANCLED WITH NO REPLACEMENT - THIS INFORMATION IS NOT CHARACTERISTIC INFORMATION, THIS INFORMATION NEEDS TO BE INPUT IN SEG W OF THE TIR. 1A MODE REPLY 0 RADCD 07CONTENT,RADIOACTIVE RADIOACTIVE CONTENT AN INDICATION OF WHETHER OR NOT THE ITEM CONTAINS RADIOACTIVE MATERIALS. SELECT REPLY CODE 10AN54 RADDJ 19DATA,RADIONUCLIDES RADIONUCLIDES DATA THE NAME AND AMOUNT OF THE RADIONUCLIDE. 2D AND 1B MODE REPLY22AG674AN55 RAMSJ 10SIZE,MEMORY,RANDOM ACCESS RANDOM ACCESS MEMORY SIZE DESIGNATES THE SIZE OF THE WORKING DATA STORAGE AVAILABLE WITHIN THE ITEM. 1D AND 1B MODE REPLY12AG67 RAVLJ 19LIFE,AVERAGE,RATED RATED AVERAGE LIFE A TERM DENOTING THE MEASUREMENT USED TO INDICATE THE AVERAGE RANGE OF LIFE OF AN ITEM. 2D AND 1B MODE REPLY21AE521AC20 RBPPB /D/ 10PERCENTAGE,CONTENT,REBUILT PARTS REBUILT PARTS CONTENT PERCENTAGE THE PERCENTAGE OF REBUILT PARTS CONTAINED IN THE ITEM. 1B MODE REPLY 0 RDALG 19DATA AND LITERATURE,REFERENCE REFERENCE DATA AND LITERATURE LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM. FULL TEXT WRITE-IN 0 RDSPJ 10READING SPEED READING SPEED THE RATE AT WHICH DATA IS TRANSFERRED FROM A STORAGE MEDIUM. 1D AND 1B MODE REPLY12AG20 REGUD 15REGULATORY ORGANIZATION REGULATORY ORGANIZATION AN INDICATION OF WHETHER THE ITEM HAS BEEN APPROVED BY A REGULATORY ORGANIZATION OR AGENCY SELECT REPLY CODE 10AJ50 RFDTJ 04DISTANCE,REFLECTIVE REFLECTIVE DISTANCE THE DISTANCE AT WHICH THE LIGHT EMITTED BY THE MIROR CANTHE MAXIMUM BE SEEN. 2D AND 1B MODE REPLY21AA051AC20 RLDDJ 10REQUIRED LANDING DISTANCE REQUIRED LANDING DISTANCE THE HORIZONTAL DISTANCE THAT AN AIRCRAFT NEEDS TO MAKE A NORMAL APPROACH FROM THE POINT OF LANDING TO THE POINT WHEN IT COMES TO A HALT. 1D AND 1B MODE REPLY11AA05 RTKDJ 10REQUIRED TAKE OFF DISTANCE REQUIRED TAKE OFF DISTANCE THE HORIZONTAL DISTANCE REQUIRED BY AN AIRCRAFT FROM A STANDING START WITH ALL ENGINES OPERATING TO ACHIEVE A TAKE OFF. 1D AND 1B MODE REPLY11AA05 RTSEG 19RELATIONSHIP TO SIMILAR EQUIPMENT RELATIONSHIP TO SIMILAR EQUIPMENT INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM. FULL TEXT WRITE-IN 0 SCLGD /D/ 19GROUP,CLASSIFICATION,SECURITY SECURITY CLASSIFICATION GROUP THE GROUP ASSIGNED TO DESIGNATE THE STATUS OF THE CLASSIFIED INFORMATION IN THE TIME-PHASED DOWNGRADING AND DECLASSIFICATION SYSTEM. SELECT REPLY CODE 10AE42 SCQPA /D/ 12QUANTITY PER PALLET,CONTAINER,SHIPPING SHIPPING CONTAINER QUANTITY PER PALLET THE NUMBER OF SHIPPING CONTAINER(S) PER PALLET. CANCLED WITH NO REPLACEMENT - THIS INFORMATION IS NOT CHARACTERISTIC INFORMATION THIS INFORMATION NEEDS TO BE INPUT IN SEG W OF THE TIR. 1A MODE REPLY 0 SDCPH /D/ 17SURFACE TREATMENT/DOCUMENT/CLASSIFICATION AND PRECEDANCE SURFACE TREATMENT/DOCUMENT/CLASSIFICATION AND PRECEDANCE THE GENERIC NOUN OF THE PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF,THE GOVERNING DOCUMENT,THE CLASSIFICATION WHICH SPECIFIES ADDITIONAL AND/OR SUPPLEMENTARY ADDITIVES,SUCH AS CLASS,GRADE,OR TYPE,AND THE ORDER OF PRECEDANCE. 2D MODE REPLY 21AP186AD09 SECLD 19CLASSIFICATION,SECURITY SECURITY CLASSIFICATION A CATEGORY ASSIGNED TO CLASSIFIED INFORMATION OR MATERIAL TO SHOW THE DEGREE OF DAMAGE TO THE INTERESTS OF NATIONAL DEFENSE WHICH COULD RESULT FROM ITS UNAUTHORIZED DISCLOSURE AND TO SHOW THE STANDARD OF PROTECTION REQUIRED TO GUARD AGAINST UNAUTHORIZED DISCLOSURE. SELECT REPLY CODE 10AE43 SENSD /D/ 18TYPE,SENSOR SENSOR TYPE INDICATES THE TYPE OF SENSOR USED BY THE ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10AK95 SERNA 19NUMBER,SERIAL,UN ORGANIZATION UN ORGANIZATION SERIAL NUMBER AN INTERNATIONAL CODE ASSIGNED WITHIN THE UNITED NATION ORGANIZATION TO DESIGNATE THE ITEM. 1A MODE REPLY 0 SFCDD 19CONDITION,SURFACE SURFACE CONDITION THE CONDITION OF THE ITEM WITH RESPECT TO THE TEXTURE OF THE SURFACE. SELECT REPLY CODE 10AN72 SFTTD 17SURFACE TREATMENT SURFACE TREATMENT THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF. SELECT REPLY CODE 10SF01 SFTUD /D/ 17SURFACE TREATMENT,INSIDE,HOUSING HOUSING INSIDE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A HOUSING INSIDE SURFACE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10SF01 SFTVD /D/ 17SURFACE TREATMENT,OUTSIDE,HOUSING HOUSING OUTSIDE SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A HOUSING OUTSIDE SURFACE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. SELECT REPLY CODE 10SF01 SHPED 14SHAPE SHAPE THE PHYSICAL CONFIGURATION OF THE ITEM. SELECT REPLY CODE 10AD07 SHPNA 19NAME,SHIPPING,PROPER,DOT DOT PROPER SHIPPING NAME THE PROPER SHIPPING NAME AS IDENTIFIED BY THE DEPARTMENT OF TRANSPORTATION (DOT) AND LISTED IN THE TITLE 49 CODE OF FEDERAL REGULATIONS (CFR), PART 172, HAZARDOUS MATERIALS TABLE. 1A MODE REPLY 0 SMPRB 10POWER RATING IN WATTS,SLEEP MODE SLEEP MODE POWER RATING IN WATTS THE RATED POWER THAT THE ITEM CONSUMES WHILE IN SLEEP MODE, MEASURED IN WATTS. 1B MODE REPLY 0 SPCLG 15SPECIAL TEST FEATURES SPECIAL TEST FEATURES TEST CONDITIONS AND RATINGS,OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT,MORE CRITICAL,OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT. FULL TEXT WRITE-IN 0 SPDSJ 04DISTANCE,SPREADING SPREADING DISTANCE THE DISTANCE OF SPREADING. 2D AND 1B MODE REPLY21AA051AC20 SPFRJ 10FORCE,SPREADING SPREADING FORCE THE AMOUNT OF FORCE REQUIRED TO SPREAD. 2D AND 1B MODE REPLY22AB161AC20 SRCEB /D/ 10SPEED AT RATED CAPACITY IN RPM,ENGAGEMENT ENGAGEMENT SPEED AT RATED CAPACITY IN RPM THE SPEED OF THE DRIVE SHAFT REQUIRED TO PRODUCE THE RATED CAPACITY OF AN ITEM,EXPRESSED IN REVOLUTIONS PER MINUTE. 1B MODE REPLY 0 SRSZA 12SIZE,SERVING SERVING SIZE NUMBER OF INDIVIDUAL PORTIONS PER CONTAINER. 1A MODE REPLY 0 SSEQA /D/ 03SIZE SEQUENCE INDICATOR SIZE SEQUENCE INDICATOR A THREE DIGIT NUMERIC CODE USED FOR SEQUENCING ITEMS IN ASCENDING SIZE ORDER FROM SMALLEST TO LARGEST SIZE. - MRC WAS CANCELED BECAUSE THE MRC DOES NOT MAKE SENSE, IT WAS NOT REPLACED AS NO ONE UNDERSTANDS THIS MRC AND WHAT THE CODED REPLIES EQUATE TO. 1A MODE REPLY 0 SSTPG /D/ 18TYPE,SUBSYSTEM SUBSYSTEM TYPE INDICATES THE TYPE OF SUBSYSTEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. FULL TEXT WRITE-IN 0 STBYJ 10POWER RATING,STANDBY STANDBY POWER RATING THE STANDBY POWER RATING AT WHICH THE ITEM IS RATED. 1D AND 1B MODE REPLY11AC33 STCDJ /D/A03DESIGNATION,CLASSIFICATION,SURFACE TREATMENT DOCUMENT SURFACE TREATMENT DOCUMENT CLASSIFICATION DESIGNATION THE DESIGNATION THAT IDENTIFIES THE PHYSICAL PRIORITIES,CONDITIONS,ETC,OF THE SURFACE TREATMENT AS EXPRESSED BY THE GOVERNING DOCUMENT. 2D AND 1A MODE REPLY21AP182AD08 STDCJ A19DOCUMENT AND CLASSIFICATION,SURFACE TREATMENT SURFACE TREATMENT DOCUMENT AND CLASSIFICATION THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL. 2D AND 1A MODE REPLY21AP331AP39 STDPH /D/ 17SURFACE TREATMENT/DOCUMENT AND PRECEDENCE SURFACE TREATMENT/DOCUMENT AND PRECEDENCE THE GENERIC NOUN OF THE PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF,THE GOVERNING DOCUMENT AND THE ORDER OF PRECEDENCE. 2D MODE REPLY 21AP186AD09 STLCH /D/ 17SURFACE TREATMENT AND LOCATION SURFACE TREATMENT AND LOCATION THE PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE ITEM AND ITS LOCATION. PLEASE USE MRC SFTT WITH ISAC CODING IN PLACE OF THIS DISCONTINUED MRC. 2D MODE REPLY 23AN736AD09 STLNH /D/ 17SURFACE TREATMENT AND LOCATION SURFACE TREATMENT AND LOCATION THE PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF. PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS THE SURFACE OF THE ITEM AND ITS LOCATION. 2D MODE REPLY 26AD093AN73 STYLL 16STYLE DESIGNATOR STYLE DESIGNATOR THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM. 1L MODE REPLY 0 SUCBJ /D/ 10CUBE,UNIT OF ISSUE UNIT OF ISSUE CUBE A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF THE UNIT OF ISSUE AND RENDERED IN CUBIC UNITS. 1D AND 1B MODE REPLY12AN76 SUPPG 15SUPPLEMENTARY FEATURES SUPPLEMENTARY FEATURES CHARACTERISTICS OR QUALITIES OF AN ITEM,NOT COVERED IN ANY OTHER REQUIREMENT,WHICH ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS EXCLUDING NSN ASSIGNMENT. FULL TEXT WRITE-IN 0 SURFD /D/ 17SURFACE TREATMENT SURFACE TREATMENT CONSISTS OF PLATING,DIP,AND/OR COATING THAT CANNOT BE WIPED OFF.PLATING AND/OR COATING IS ANY CHEMICAL AND/OR METALLIC ADDITIVE,ELECTROCHEMICAL,OR MILD MECHANICAL PROCESS WHICH PROTECTS A SURFACE. PLEASE USE MRC SFTT IN PLACE OF THIS DISCONTINUED MRC. SELECT REPLY CODE 10AD09 SUWTJ /D/ 10WEIGHT,UNIT OF ISSUE UNIT OF ISSUE WEIGHT THE MEASURED WEIGHT OF THE ACTUAL CONTAINER(S) OR SUPPORTING DEVICE(S) WHICH IS IN DIRECT CONTACT WITH THE ITEM AND ITS CONTENTS. 1D AND 1B MODE REPLY12AN75 SWALD 08LOCATION,ACTUATOR,SWITCH SWITCH ACTUATOR LOCATION INDICATES THE POSITION OF THE SWITCH ACTUATOR ON THE ITEM. SELECT REPLY CODE 10AJ91 SWBTD 18TYPE,BODY,SWITCH SWITCH BODY TYPE INDICATES THE TYPE OF SWITCH FOR WHICH THE BODY IS DESIGNED. SELECT REPLY CODE 10AC82 TADMJ /D/ 04DIAMETER,TAPERED TAPERED DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CIRCULAR CROSS SECTION OF THE TAPERED PORTION AND TERMINATES AT THE CIRCUMFERENCE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 TAQTA /D/ 12QUANTITY,ATTACHMENT ATTACHMENT QUANTITY INDICATES THE NUMBER OF ATTACHMENT(S). MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1A MODE REPLY 0 TESTJ A15TEST DATA DOCUMENT TEST DATA DOCUMENT THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT. 1D AND 1A MODE REPLY11AC28 TEXTG 19DESCRIPTION,ITEM,GENERAL CHARACTERISTICS GENERAL CHARACTERISTICS ITEM DESCRIPTION A RECORDING OF THE PHYSICAL,FUNCTIONAL,AND PERFORMANCE CHARACTERISTICS FOR AN ITEM OF SUPPLY. FULL TEXT WRITE-IN 0 THDSJ A13THREAD SIZE AND SERIES/TYPE DESIGNATOR THREAD SIZE AND SERIES/TYPE DESIGNATOR DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE. 1D AND 1A MODE REPLY12AH06 THKSJ 04THICKNESS THICKNESS A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH. 1D AND 1B MODE REPLY11AA05 THLCH /D/ 13THREAD SERIES DESIGNATOR AND LOCATION THREAD SERIES DESIGNATOR AND LOCATION A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER AND THE THREAD LOCATION. 2D MODE REPLY 22AH063AN73 THPEA 07THERAPEUTIC EQUIVALENT THERAPEUTIC EQUIVALENT AN INDICATION OF THE SAME PREDICTABLE THERAPEUTIC EFFECT AS DETERMINED BY THE FOOD AND DRUG ADMINISTRATION (FDA) FOR AN ITEM OF SUPPLY WHEN ADMINISTERED UNDER THE CONDITIONS AS SPECIFIED IN THE LABELING. 1A MODE REPLY 0 THSDD 13THREAD SERIES DESIGNATOR THREAD SERIES DESIGNATOR A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER. SELECT REPLY CODE 10AH06 THTHJ /D/ 10TOOTH,THICKNESS THICKNESS TOOTH THE TANGENTIAL THICKNESS OF A CIRCULAR-GEAR TOOTH MEASURED ALONG A CHORD OF OF THE PITCH CIRCLE. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 2D AND 1B MODE REPLY21AA051AC20 TKWTJ 10TAKE OFF WEIGHT TAKE OFF WEIGHT THE MAXIMUM AIRCRAFT WEIGHT PERMITTED FOR TAKE OFF. 2D AND 1B MODE REPLY22AG671AC20 TLLCJ /D/ 13THREAD LENGTH AND LOCATION THREAD LENGTH AND LOCATION A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS AND THE LOCATION. 3D AND 1B MODE REPLY31AA051AC203AN73 TMDNA 19DESIGNATION,TYPE/MODEL TYPE/MODEL DESIGNATION THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM. 1A MODE REPLY 0 TMQYJ A19ITEMS AND QUANTITY,FURNISHED FURNISHED ITEMS AND QUANTITY THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE. 1D AND 1A MODE REPLY13AB28 TPLCJ /D/T13THREAD PITCH DIAMETERS IN INCHES AND LOCATION THREAD PITCH DIAMETERS IN INCHES AND LOCATION THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT THREAD,EXPRESSED IN INCHES,AND THE LOCATION. 1D AND 1F MODE REPLY13AN73 TPLNF /D/T13THREAD PITCH DIAMETERS IN INCHES THREAD PITCH DIAMETERS IN INCHES THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT THREAD,EXPRESSED IN INCHES. 1F MODE REPLY 0 TPMMJ 13THREAD PITCH IN MILLIMETERS THREAD PITCH IN MILLIMETERS THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS. 1D AND 1B MODE REPLY11AC20 TQLCJ /D/A13THREAD QUANTITY PER INCH AND LOCATION THREAD QUANTITY PER INCH AND LOCATION THE NUMBER OF THREADS PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS,AND THE LOCATION. 1D AND 1A MODE REPLY13AN73 TTQYJ A18TYPE AND QUANTITY,TERMINAL TERMINAL TYPE AND QUANTITY INDICATES THE TYPE AND NUMBER OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION. 1D AND 1A MODE REPLY13AN89 TYCCD 18TYPE,COMPATIBLE CONNECTOR COMPATIBLE CONNECTOR TYPE INDICATES THE TYPE OF CONNECTOR THAT CAN BE USED WITH THE ITEM. SELECT REPLY CODE 10AF42 TYCHH 18TYPE,CHANNEL CHANNEL TYPE INDICATES THE TYPE OF CHANNEL AND WHEN IT IS USED. 2D MODE REPLY 22AL992AD48 UKAAD 15SR-1 SPECIFICATION AND/OR STANDARD DATA SR-1 SPECIFICATION AND/OR STANDARD DATA THE KIND OF SPECIFICATION AND/OR STANDARD DOCUMENT OR MANUFACTURERS CONTROL DRAWING USED TO ESTABLISH THE CONCEPT OF THE ITEM BEING DESCRIBED. SELECT REPLY CODE 10AN59 UKABG /D/ 15SR-1 IDENTIFYING TITLE OF THE DOCUMENT SR-1 IDENTIFYING TITLE OF THE DOCUMENT THE IDENTIFYING TITLE OF THE SPECIFICATION AND/OR STANDARD DOCUMENT USED TO ESTABLISH THE CONCEPT OF THE ITEM BEING DESCRIBED. /THIS INFORMATION WAS FORMERLY REQUIRED TO BE GIVEN IN REPLY TO SUBREQUIREMENT A OF SR-1. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. FULL TEXT WRITE-IN 0 UKACA 15SR-1 SOURCE OR SPECIFICATION CONTROL MANUFACTURER SR-1 SOURCE OR SPECIFICATION CONTROL MANUFACTURER THE MANUFACTURER NAME AND ADDRESS IDENTIFYING THE SPECIFICATION OR SOURCE CONTROL DRAWING USED TO ESTABLISH THE CONCEPT OF THE ITEM BEING DESCRIBED. (THIS INFORMATION WAS FORMERLY REQUIRED TO BE GIVEN IN REPLY TO SUBREQUIREMENT A OF SR-1.) 1A MODE REPLY 0 UKADG 15SR-1 LATEST APPLICABLE SYMBOL AND/OR NUMBER SR-1 LATEST APPLICABLE SYMBOL AND/OR NUMBER THE CURRENT NUMBER/S/,LETTER/S/,AND/OR SYMBOL/S/ IDENTIFYING THE SPECIFICATION AND/OR STANDARD DOCUMENT OR THE MANUFACTURERS SPECIFICATION OR SOURCE CONTROL DRAWING USED TO ESTABLISH THE CONCEPT OF THE ITEM BEING DESCRIBED. /THIS INFORMATION WAS FORMERLY REQUIRED TO BE GIVEN IN REPLY TO SUBREQUIREMENT B OF SR-1./ FULL TEXT WRITE-IN 0 UKAEG /D/ 15SR-1 SPECIFIC REVISION OR AMENDMENT SR-1 SPECIFIC REVISION OR AMENDMENT THE NUMBER/S/,LETTER/S/,AND/OR SYMBOL/S/ IDENTIFYING A SPECIFIC ISSUE OF A SPECIFICATION AND/OR STANDARD DOCUMENT OR MANUFACTURERS SPECIFICATION OR SOURCE CONTROL DRAWING USED TO ESTABLISH THE CONCEPT OF THE ITEM BEING DESCRIBED. /THIS INFORMATION WAS FORMERLY REQUIRED TO BE GIVEN IN REPLY TO SUBREQUIREMENT /1/B OF SR-1. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. FULL TEXT WRITE-IN 0 UKAFG 15SR-1 TYPE DESIGNATOR SR-1 TYPE DESIGNATOR THE NUMBER(S),LETTER(S),AND/OR SYMBOL(S) IDENTIFYING THE TYPE DESIGNATOR (SUCH AS STYLE,CLASS,GRADE,SIZE,TABLE,REFERENCE,ETC) CONTAINED IN THE DOCUMENT OR DRAWING USED TO ESTABLISH THE CONCEPT OF THE ITEM BEING DESCRIBED. FULL TEXT WRITE-IN 0 UKAGA /D/ 15SR-5 MANUFACTURERS DATA SR-5 MANUFACTURERS DATA THE NAME OF THE MANUFACTURER RESPONSIBLE FOR THE DATA USED TO ESTABLISH THE CONCEPT OF THE ITEM BEING DESCRIBED. (APPLICABLE ONLY TO TYPES 1A,1B,4A,OR 4B ITEM IDENTIFICATION.) MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1A MODE REPLY 0 UKAHG 15SR-5 MANUFACTURERS NUMBER SR-5 MANUFACTURERS NUMBER THE NUMBER (SUCH AS SYMBOL(S) AND/OR TRADE NAME OF THE ITEM) BY WHICH THE DATA USED TO ESTABLISH THE CONCEPT OF THE ITEM BEING DESCRIBED IS KNOWN TO THE MANUFACTURER. FULL TEXT WRITE-IN 0 UKAJG /D/ 15SR-5 TECHNICAL DIFFERENTIATING CHARACTERISTICS SR-5 TECHNICAL DIFFERENTIATING CHARACTERISTICS THE RECORDING OF AN ITEM OF SUPPLY FEATURE NOT INHERENT IN THE MANUFACTURERS NUMBER OR WHEN THE MANUFACTURERS NUMBER DOES NOT FULLY IDENTIFY THE ITEM OF SUPPLY BECAUSE IT COVERS A RANGE OF ITEMS. FULL TEXT WRITE-IN 0 UKAKG /D/ 10VISCOSITY IN DEG CELSIUS VISCOSITY IN DEG CELSIUS THE KINEMATIC UNITS /CENTISTOKES/ OF THE ITEM AT A SPECIFIED TEMPERATURE,EXPRESSED IN DEGREES CELSIUS. FULL TEXT WRITE-IN 0 UKALG /D/ 10VISCOSITY IN DEG CELSIUS,MAXIMUM MAXIMUM VISCOSITY IN DEG CELSIUS THE MAXIMUM KINEMATIC UNITS /CENTISTOKES/ OF THE ITEM AT A SPECIFIED TEMPERATURE,EXPRESSED IN DEGREES CELSIUS. FULL TEXT WRITE-IN 0 UKAMB /D/ 10POUR POINT IN DEG CELSIUS POUR POINT IN DEG CELSIUS THE LOWEST TEMPERATURE AT WHICH THE ITEM WILL POUR,EXPRESSED IN DEGREES CELSIUS. 1B MODE REPLY 0 UKANB /D/ 10TETRAETHYL LEAD ALLOWABLE IN GRAMS PER LITER,MAXIMUM MAXIMUM TETRAETHYL LEAD ALLOWABLE IN GRAMS PER LITER A MEASUREMENT OF THE MAXIMUM TETRAETHYL LEAD ALLOWABLE,EXPRESSED IN GRAMS PER LITER. 1B MODE REPLY 0 UKAPJ /D/ 04WIDTH AT THREADED END,FLAT FLAT WIDTH AT THREADED END NONE. 2D AND 1B MODE REPLY21AA051AC20 UKAQD /D/ 08LOCATION,DRIVE,INTERNAL INTERNAL DRIVE LOCATION INDICATES THE INTERNAL DRIVE LOCATION ON AN ITEM. SELECT REPLY CODE 10AJ91 UKARH /D/ 06HEAT TREATMENT AND LOCATION HEAT TREATMENT AND LOCATION A PROCESS IN WHICH THE METAL IN THE SOLID STATE IS SUBJECTED TO ONE OR MORE TEMPERATURE CYCLES TO CONFER CERTAIN DESIRED PROPERTIES AND THE LOCATION OF AN ITEM TO WHICH A SPECIFIC HEAT TREATMENT IS APPLIED. /NOTE-HEATING FOR THE SOLE PURPOSE OF HOT WORKING IS EXCLUDED FROM THE MEANING OF THE DEFINITION./ 2D MODE REPLY 22AD053AJ91 UKASD 03DESIGNATION,GRADE,STRENGTH STRENGTH GRADE DESIGNATION A NUMERIC AND/OR ALPHA-NUMERIC DESIGNATOR WHICH INDICATES THE STRENGTH RATING OF A THREADED FASTENER. THE CODE IS COMPRISED OF TWO NUMBERS SEPARATED BY A DOT. THE CODE TO THE LEFT OF THE DOT REPRESNETS THE ULTIMATE STRENGTH IN MEGA PASCALS (MPA) WHILE THE NUMBER TO THE RIGHT OF THE DOT REPRESENTS THE YEILD STRENGTH (MEGA PASCALS - MPA) OR STRESS AT 0,2 PERMANENT SET (MPA) DEPENDING ON THE PROPERTY CLASS. SELECT REPLY CODE 10AN67 UKATD /D/ 18TYPE,MATERIAL,RESISTOR ELEMENT RESISTOR ELEMENT MATERIAL TYPE INDICATES THE MATERIAL TYPE OF WHICH THE RESISTOR ELEMENT IS MADE. SELECT REPLY CODE 10AN48 UKAWB /D/ 10TEMP,SURFACE,MAXIMUM MAXIMUM SURFACE TEMP THE PERMISSIBLE MAXIMUM TEMPERATURE AT THE OUTER SURFACE OF THE ITEM. 1B MODE REPLY 0 UKAXB /D/ 10PERCENT AFTER ENDURANCE TEST,DRIFT,RESISTANCE RESISTANCE DRIFT PERCENT AFTER ENDURANCE TEST THE PERCENT OF ALLOWABLE RESISTANCE DRIFT AFTER AN ENDURANCE TEST. 1B MODE REPLY 0 UKAYA /D/ 10TIME IN HOURS,TEST,ENDURANCE ENDURANCE TEST TIME IN HOURS THE TIME EXPENDED FOR AN ENDURANCE TEST,EXPRESSED IN HOURS. 1A MODE REPLY 0 UKAZB /D/ 10TEMP,AMBIENT,ENDURANCE TEST ENDURANCE TEST AMBIENT TEMP THE AMBIENT TEMPERATURE AT WHICH THE ENDURANCE TEST/S/ WAS CARRIED OUT. 1B MODE REPLY 0 UKBAB /D/ 10VOLTAGE,ISOLATION ISOLATION VOLTAGE THE VOLTAGE THAT MAY BE APPLIED BETWEEN TERMINALS OF THE ITEM AND A METAL PLATE ONTO WHICH THE ITEM IS CLAMPED WITHOUT INSULATION BREAKDOWN OCCURRING. 1B MODE REPLY 0 UKBBB /D/ 10VOLTAGE,ELEMENT,LIMITING LIMITING ELEMENT VOLTAGE THE MAXIMUM WORKING VOLTAGE THAT MAY BE APPLIED BETWEEN THE TERMINALS ON AN ITEM. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1B MODE REPLY 0 UKBCA /D/ 19CATEGORY,CLIMATIC CLIMATIC CATEGORY THE CLIMATIC CONDITIONS UNDER WHICH THE ITEM WILL PERFORM SATISFACTORILY. 1A MODE REPLY 0 UKBDJ /D/ 04DIAMETER,MAJOR,MOUNTING HOLE,COUNTERSUNK COUNTERSUNK MOUNTING HOLE MAJOR DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MAJOR PORTION OF THE MOUNTING HOLE. 2D AND 1B MODE REPLY21AA051AC20 UKBFJ /D/ 04DIAMETER,INSIDE,TUBE,NOMINAL NOMINAL TUBE INSIDE DIAMETER THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TUBE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 UKBGJ 10VOLTAGE RATING PER UNIT THICKNESS,MATERIAL,DIELECTRIC DIELECTRIC MATERIAL VOLTAGE RATING PER UNIT THICKNESS THE MAXIMUM POTENTIAL GRADIENT THE INSULATING MATERIAL CAN WITHSTAND,PER UNIT THICKNESS,WITHOUT RUPTURE. 1D AND 1B MODE REPLY12AP24 UKBHB /D/ 10VOLTAGE DROP IN VOLTS VOLTAGE DROP IN VOLTS THE VOLTAGE MEASURED AT THE TERMINALS OF THE FUSE LINK WHEN THE MAXIMUM RATED CURRENT IS BEING CARRIED,EXPRESSED IN VOLTS. 1B MODE REPLY 0 UKBJJ /D/ 10TIME IN SECONDS,DELAY,CIRCUIT OVER-CURRENT PRE-ARCING CIRCUIT OVER-CURRENT PRE-ARCING DELAY TIME IN SECONDS THE TIME BETWEEN THE COMMENCEMENT OF A CURRENT LARGE ENOUGH TO CAUSE A BREAK IN THE FUSE ELEMENT AND THE INSTANT WHEN THE ARC IS INITIATED AT A SPECIFIED PERCENTAGE OF ITS NORMAL CURRENT RATING,EXPRESSED IN SECONDS. 1D AND 1B MODE REPLY12AP37 UKBKB /D/ 10CURRENT IN AMPS,INTERRUPTING,MAXIMUM MAXIMUM INTERRUPTING CURRENT IN AMPS THE MAXIMUM CURRENT THAT A PROTECTIVE DEVICE WILL INTERRUPT OR SHORT CIRCUIT WITHOUT ABNORMAL SELF OR ENVIRONMENTAL DETERIORATION,EXPRESSED IN AMPERES. MRC DISCONTINUED WITH NO REPLACEMENT ON 01/12/2024. 1B MODE REPLY 0 UKBLJ /D/ 10TOLERANCE PER UNIT CONTAINER,DIAMETER DIAMETER TOLERANCE PER UNIT CONTAINER THE PERMISSABLE DIFFERENCE OF THE AVERAGE DIAMETER OF THE INDIVIDUAL BALLS WITHIN ANY ONE UNIT CONTAINER. 1D AND 1B MODE REPLY11AA05 UKBMJ /D/ 10TOLERANCE PER BALL,SPHERICITY SPHERICITY TOLERANCE PER BALL THE MAXIMUM PERMISSABLE DEVIATION FROM A TRUE SPHERE DETERMINED BY TAKING A NUMBER OF MEASUREMENTS IN DIFFERENT PLANES AROUND THE BALL CIRCUMFERENCE. 1D AND 1B MODE REPLY11AA05 UKBNJ /D/ 04SIZE,TRADE,NOMINAL NOMINAL TRADE SIZE THE SINGLE NOMINAL SIZE DESIGNATION THAT REPRESENTS MORE SPECIFIC CROSS-SECTIONAL DIMENSIONS OF THE ITEM. 1D AND 1B MODE REPLY11AA05 UKBPD /D/ 19CATEGORY,DESIGN DESIGN CATEGORY AN INDICATION OF THE TEST REQUIREMENTS TO WHICH A SPRING CONFORMS. SELECT REPLY CODE 10AP46 UKBQJ /D/ 10LOAD,TEST,PROOF PROOF TEST LOAD A SPECIFIED TEST LOAD WHICH THE ITEM MUST WITHSTAND WITHOUT DAMAGE. 1D AND 1B MODE REPLY12AG67 UKBRJ /D/ 10VOLTAGE RATING IN VOLTS AND CURRENT TYPE PER SECTION,CONTINUOUS,NONDERATED NONDERATED CONTINUOUS VOLTAGE RATING IN VOLTS AND CURRENT TYPE PER SECTION THE HIGHEST POTENTIAL AND TYPE OF CURRENT THAT MAY BE CONTINUOUSLY APPLIED TO THE ITEM PER SECTION AT THE HIGHEST OPERATING TEMPERATURE PERMISSIBLE WITHOUT VOLTAGE DERATING,EXPRESSED IN VOLTS. 2D AND 1B MODE REPLY23AJ912AN87 UKBSJ /D/ 10RESISTANCE AT 20 DEG CELSIUS,DC,INSULATION INSULATION DC RESISTANCE AT 20 DEG CELSIUS DIRECT CURRENT RESISTANCE BETWEEN TWO CONDUCTORS THAT ARE SEPARATED BY AN INSULATING MATERIAL,MEASURED AT 20 DEGREES CELSIUS. 1D AND 1B MODE REPLY11AA57 UKBTD /D/ 19CONFIGURATION,DEVICE,INFLATION INFLATION DEVICE CONFIGURATION AN INDICATION OF THE VALUE CONFIGURATION. SELECT REPLY CODE 10AP49 UKBWA /D/ 19POSITION,POLARIZATION POLARIZATION POSITION THE SPECIFIC POSITION OF THE POLARIZATION DEVICE. 1A MODE REPLY 0 UKBXJ /D/ 04DISTANCE,CENTER TO CENTER,CONTACT CONTACT CENTER TO CENTER DISTANCE THE DISTANCE FROM THE CENTER OF ONE CONTACT TO THE CENTER OF THE NEXT CONTACT. 1D AND 1B MODE REPLY11AA05 UKBYD /D/ 11METHOD,ORIENTATION ORIENTATION METHOD THE SPECIFIC METHOD USED TO PREVENT MISMATING OF ITEMS HAVING THE SAME SHELL SIZE AND CONTACT ARRANGEMENT. SELECT REPLY CODE 10AP35 UKBZA /D/ 19POSITION,ORIENTATION ORIENTATION POSITION THE DESIGNATOR THAT IDENTIFIES THE ANGULAR POSITION OF THE ORIENTATION METHOD. 1A MODE REPLY 0 UKCAB 10STRESS,LOAD,PROOF PROOF LOAD STRESS THE DESIGNATION NUMBER IS EQUAL TO ONE-HUNDREDTH OF THE SPECIFIED PROOF LOAD STRESS IN NEWTON PER SQUARE MILLIMETERS. THIS PROOF LOAD STRESS CORRESPONDS TO THE MINIMUM TENSILE STRENGTH OF A BOLT OR SCREW WITH WHICH THE NUT SHOULD BE ASSEMBLED SO AS TO ENSURE THE LOADING CAPACITY OF THE BOLTED CONNECTION UP TO THE MINIMUM YIELD STRENGTH OF THE BOLT. 1B MODE REPLY 0 UKCBJ /D/ 04SIZE ACCOMMODATED,CONDUIT,NOMINAL NOMINAL CONDUIT SIZE ACCOMMODATED THE NOMINAL SIZE THAT INDICATES THE ACTUAL OUTSIDE DIAMETER OF THE ITEM ACCOMMODATED. 1D AND 1B MODE REPLY11AA05 UKCCG /D/ 15SR-5 MANUFACTURERS SPECIFIC REVISION OR AMENDMENT SR-5 MANUFACTURERS SPECIFIC REVISION OR AMENDMENT THE NUMBER(S), LETTER(S), AND/OR SYMBOLS IDENTIFYING A SPECIFIC ISSUE OF A MANUFACTURERS NUMBER WHICH WHEN ADDED TO THE SR-5 MANUFACTURERS NUMBER REPLY UNIQUELY IDENTIFIES THE DRAWING/FACSIMILE USED TO ESTABLISH THE CONCEPT OF THE ITEM BEING DESCRIBED. FULL TEXT WRITE-IN 0 VANGJ A10VIEW,ANGLE ANGLE VIEW THE ANGLE OF VIEW. 3D AND 1A MODE REPLY31AP383AK331AC20 WAQSJ 12WIDTH AND QUANTITY,SLOT SLOT WIDTH AND QUANTITY A MEASUREMENT OF THE LONGEST DIMENSION OF THE SLOT, IN DISTINCTION FROM WIDTH. 3D AND 1B MODE REPLY31AA051AC203AP65 WDTHJ 04WIDTH WIDTH A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS. 1D AND 1B MODE REPLY11AA05 WGAAJ 10WING AREA WING AREA SUM OF WINGS AREAS PROJECTED HORIZONTALLY. 1D AND 1B MODE REPLY12AG67 WGHTJ /D/ 10WEIGHT WEIGHT A RELATIVE MEASURE OF THE MASS OF AN ITEM WITH RESPECT TO ITS DENSITY. PLEASE USE MRC ASHR IN PLACE OF THIS DISCONTINUED MRC. 1D AND 1B MODE REPLY11AB10 WKLGJ 04LENGTH,WORKING WORKING LENGTH NONE 2D AND 1B MODE REPLY21AA051AC20 WLBLA /D/ 19CODE,LABEL,WARNING,DOT DOT WARNING LABEL CODE THE WARNING LABEL CODE ASSIGNED BY THE DEPARTMENT OF TRANSPORTATION (DOT) TO EACH PACKAGE OR CONTAINMENT DEVICE OFFERED FOR TRANSPORTATION OF A HAZARDOUS MATERIAL WHICH MEETS ONE OR MORE HAZARD CLASS DEFINITIONS IN ACCORDANCE WITH THE TITLE 49 CODE OF FEDERAL REGULATIONS (CFR), PART 172, HAZARDOUS MATERIALS TABLE. CANCLED WITH NO REPLACEMENT - THIS INFORMATION IS NOT CHARACTERISTIC INFORMATION, THIS INFORMATION NEEDS TO BE INPUT IN SEG G OF THE TIR 1A MODE REPLY 0 WPNSA /D/ 19IDENTIFICATION,SYSTEM,WEAPON WEAPON SYSTEM IDENTIFICATION THE DSA REGISTRATION NUMBER ASSIGNED TO EACH SYSTEM TO IDENTIFY SUPPORTING ITEMS FOR SPECIAL MANAGEMENT AND TO OPTIMIZE AVAILABILITY AND DELIVERY OF ITEMS FROM STOCK. 1A MODE REPLY 0 WPNTA /D/ 12QUANTITY,FIRING LINE FIRING LINE QUANTITY THE NUMBER OF FIRING LINE(S) WHICH COULD BE CONNECTED TO THE ITEM. 1A MODE REPLY 0 WPNUA /D/ 12CAPACITY,FIRING FIRING CAPACITY THE NUMBER OF ELECTRIC BLASTING CAP(S) WHICH COULD BE INITIATED BY THE ITEM. 1A MODE REPLY 0 WRSPJ 10WRITING SPEED WRITING SPEED THE RATE AT WHICH DATA IS TRANSFERRED TO A STORAGE MEDIUM. 1D AND 1B MODE REPLY12AG20 ZZZKJ A15SPECIFICATION/STANDARD DATA SPECIFICATION/STANDARD DATA THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY. 1D AND 1A MODE REPLY11AN62 ZZZPJ X15PURCHASE DESCRIPTION IDENTIFICATION PURCHASE DESCRIPTION IDENTIFICATION THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY. 1D AND 1A MODE REPLY15AN63 ZZZSG /D/ 15NONGOVERNMENT DOCUMENT DATA NONGOVERNMENT DOCUMENT DATA THE PROFESSIONAL GROUP,INDUSTRIAL ASSOCIATION,OR MANUFACTURER,S SPECIFICATION OR STANDARD WHICH ESTABLISHES THE ITEM OF SUPPLY BEING DESCRIBED. INCLUDES THE FEDERAL SUPPLY CODE FOR MANUFACTURER /FSCM/ OF THE ENTITY CONTROLLING THE DOCUMENT. (THIS INFORMATION WAS FORMERLY PROVIDED IN PART BY RESPONSES TO SR-1 FOR OTHER THAN GOVERNMENT CONTROLLED DOCUMENTS.) FULL TEXT WRITE-IN 0 ZZZTJ A15NONDEFINITIVE SPEC/STD DATA NONDEFINITIVE SPEC/STD DATA THE NUMBER,LETTER,OR SYMBOL THAT INDICATES THE TYPE,STYLE,GRADE,CLASS,AND THE LIKE,OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD. 1D AND 1A MODE REPLY12AD08 ZZZVG 15FSC APPLICATION DATA FSC APPLICATION DATA THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY. FULL TEXT WRITE-IN 0 ZZZWG 15DEPARTURE FROM CITED DOCUMENT DEPARTURE FROM CITED DOCUMENT THE TECHNICAL DIFFERENTIATING CHARACTERISTIC/S/ OF AN ITEM OF SUPPLY WHICH DEPART/S/ FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL,OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS,OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD. FULL TEXT WRITE-IN 0 ZZZXG 15DEPARTURE FROM CITED DESIGNATOR DEPARTURE FROM CITED DESIGNATOR THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD,EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS. FULL TEXT WRITE-IN 0 ZZZYG 15REFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS REFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS. FULL TEXT WRITE-IN 0 9000A /D/ 15DATE OF PRECEDING RECORD DATE OF PRECEDING RECORD /ENTERED AS YEAR-MONTH-DAY IN NUMERICS//DATE OF PRECEDING RECORD NOT TO BE ENTERED IN THE INITIALLY SUBMITTED ILDT FOR AN UPGRADED ITEM IDENTIFICATION IT MUST BE ENTERED IN ALL SUBSEQUENT ILDTS/. 1A MODE REPLY 0 9001A /D/ 15NONDUPLICATION OF NSN NONDUPLICATION OF NSN INDICATES THAT, THOUGH CHARACTERISTICS SEEM SIMILAR, RESEARCH REVEALED DIFFERENCES REQUIRING ASSIGNMENT OF DIFFERENT NSN. 1A MODE REPLY 0 9002A /D/ 15FORMER TYPE CODE FORMER TYPE CODE /INDICATES TYPE OF DESCRIPTION HAS BEEN CHANGED,AS FROM TYPE 1A/K/ TO TYPE 1/. 1A MODE REPLY 0 9003G /D/ 15PREVIOUS ITEM NAME PREVIOUS ITEM NAME /ENTER THE PREVIOUS ITEM NAME IN FULL TEXT/. FULL TEXT WRITE-IN 0 9004A /D/ 15PREVIOUS FEDERAL SUPPLY CLASSIFICATION PREVIOUS FEDERAL SUPPLY CLASSIFICATION /THE FSC PREVIOUSLY ASSIGNED TO THE ITEM BEING DESCRIBED/. 1A MODE REPLY 0 9005G /D/ 15DECLASSIFICATION OF ITEM DECLASSIFICATION OF ITEM /THE DIRECTIVE AUTHORIZING DOWNGRADING OF A PREVIOUSLY SECURITY CLASSIFIED ITEM TO UNCLASSIFIED STATUS/. FULL TEXT WRITE-IN 0 9006D /D/ 15CONCURRENCE CONCURRENCE NONE. SELECT REPLY CODE 10AM72 9007D /D/ 15PREVIOUS CLASSIFICATION PREVIOUS CLASSIFICATION THE PREVIOUS SECURITY CLASSIFICATION OF AN ITEM. SELECT REPLY CODE 10AM68